This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

In view of the problem that the output thrust of solenoid actuator is affected by various factors and is difficult to calculate in actual working conditions, this paper proposes a semi-analytical model constructed by magnetic field subdomain method with internal and external boundary conditions in cylindrical coordinate system for calculation, and the general solution equations of magnetic vector potential for each subdomain are derived and solved by MATLAB. Taking a push-pull electromagnet as an example, the finite element simulation and experimental comparative analysis are carried out. The correctness and applicable conditions of the subdomain method are illustrated by comparing the gradient plot of magnetic vector potential, inductance curve and electromagnetic force. By calculating the output thrust after considering the core gravity, spring force and electromagnetic force, it is shown that this method has the advantage of computational flexibility compared with the finite element method, and it is easier to write special algorithms according to various working conditions to calculate the important parameters in engineering applications.

Cloud computing refers to applications delivered as services over the Internet. Cloud systems employ policies that are inherently dynamic in nature and that depend on temporal conditions defined in terms of external events, such as the measurement of bandwidth, use of hosts, intrusion detection or specific time events. In this paper, we investigate an optimized resource management scheme named v-Mapper. The basic premise of v-Mapper is to exploit application-awareness concepts using software-defined networking (SDN) features. This paper makes three key contributions to the field: (1) We propose a virtual machine (VM) placement scheme that can effectively mitigate the VM placement issues for data-intensive applications; (2) We propose a validation scheme that will ensure that a service is entertained only if there are sufficient resources available for its execution and (3) We present a scheduling policy that aims to eliminate network load constraints. An evaluation was carried out with various benchmarks and demonstrated that v-Mapper shows improved performance over other state-of-the-art approaches in terms of average task completion time, service delay time and bandwidth utilization. Given the growing importance of supporting large-scale data processing and analysis in datacentres, the v-Mapper system has the potential to make a positive impact in improving datacentre performance in the future.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

By introducing environmental mediator, for avoiding randomness in selecting indicators and subjectivity in deciding interaction path coefficients to reveal interaction mechanism among forest industry, ecology and environmental capacity, structural Pressure–State–Impact–Response (PSIR) and quantitative Structural Equation Modeling (SEM) are utilized with data on thirty–one provinces of China. We can find that: (i) forest industry has a negative influence on ecology, whereas ecology has a positive influence on industry; (ii) the destructive influence that industry has on ecology is much greater than the positive effect ecology has on industry; and (iii) environmental capacity plays a partial mediating role between industry and ecology. According to these results we can conclude that: (i) forest industry and ecology are not in a symbiotic relationship and have not reached a level of ecological security; (ii) the interaction between industry and ecology is in a period of transition from antagonistic to beneficial; and (iii) industry dominates ecology. However, we prospect the following advice: (i) methods of forest industry should be changed; (ii) new modes of industrial integration and circular economy should be developed; and (iii) the ability of the environment to sustain itself should be enhanced. The level of forest ecological security to discuss the symbiotic mechanism of industry and ecology will propose to be measured in future.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Taiwan’s auditors have suffered from processing excessive audit data, including drawing audit evidence. This study advances sampling techniques by integrating machine learning with sampling. This machine learning integration helps avoid sampling bias, keep randomness and variability, and target the risker samples. We first apply a Naive Bayes classifier to classify data into some classes. Next, a user-based, item-based, or hybrid approach is employed to draw audit evidence. The representativeness index is the primary metric for measuring the representativeness of audit evidence. The user-based approach denotes the selection of samples between two percentiles in a class as audit evidence. It may be equivalent to a combination of monetary and variable sampling methods. The item-based approach represents the choice of risky samples as audit evidence. It may be identical to a combination of non-statistical and monetary sampling methods. Auditors can hybridize those user-based and item-based approaches to balance representativeness and riskiness in selecting audit evidence. Three experiments show that sampling using machine learning integration has the benefits of drawing unbiased samples, handling complex patterns, correlations, and unstructured data, and improving efficiency in sampling big data. However, the limitations are the classification accuracy output by machine learning algorithms and the range of prior probabilities.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

In the dynamic landscape of the telecommunications industry, understanding and mitigating customer churn is paramount for maintaining competitive advantage and sustaining revenue streams. This comprehensive literature review delves into the intricacies of customer churn prediction, a crucial aspect in fortifying the bond between telecom businesses and their customers. The review methodically analyzes 11 articles published between 2000 and March 2024, spotlighting the strategic role of Customer Relationship Management and the prevalence of high churn rates that necessitate a shift from customer acquisition to retention strategies. Furthermore, the review navigates through the challenges inherent in churn prediction, including the complexities of managing large, imbalanced, and noisy datasets and the intricacies involved in model selection and optimization. Despite these challenges, the paper highlights the superior capability of machine learning techniques in handling complex datasets to provide accurate predictions, albeit acknowledging their practical complexities. The main aim of the study is to provide an overview, serving as a knowledge base for researchers interested in machine learning techniques within the realm of telecommunications.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

Herein, we present the design technique of a resonant rectifier for piezoelectric (PE) energy harvesting. We propose two diode equivalents to reduce the voltage drop in the rectifier operation, a minuscule-drop-diode equivalent (MDDE) and a low-drop-diode equivalent (LDDE). The diode equivalents are embedded in resonant rectifier integrated circuits (ICs), which use symmetric bias-flip to reduce the power wasted for charging and discharging the internal capacitance of a PE transducer. The self-startup function is supported by synchronously generating control pulses for the bias-flip from the PE transducer. Two resonant rectifier ICs, using both MDDE and LDDE, are fabricated in a 0.18 μm CMOS process and their performances are characterized under external and self-power conditions. Under the external-power condition, the rectifier using LDDE delivers an output power POUT of 564 μW and a rectifier output voltage VRECT of 3.36 V with a power conversion efficiency (PCE) of 90.1%. Under self-power conditions, the rectifier using MDDE delivers a POUT of 288 μW and a VRECT of 2.4 V with a corresponding PCE of 74.6%. The result shows that the power extraction capability of the proposed rectifier is 5.9 and 3.0 times higher than that of a conventional full-bridge rectifier.

This article proposes a measurement solution designed to monitor instantaneous frequency in power systems. It uses a data acquisition module and a GPS receiver for time stamping. A program in Python takes care of receiving the data, calculating the frequency, and finally transferring the measurement results to a database. The frequency is calculated with two different methods, which are compared in the article. The stored data is visualized using the Grafana platform, thus demonstrating its potential for comparing scientific data. The system as a whole constitutes an efficient low cost solution as a data acquisition system.

The article presents several innovative systems developed through student laboratory projects, including two autonomous vehicles, a four-legged walking robot, an active ankle-foot orthosis, a ball on beam balancing mechanism, a ball on plate system, and a manipulator arm—all powered by pneumatic artificial muscles (PAMs). Fluidic muscles offer significant potential in various mechatronic systems, robots, and manipulators due to their flexible, lightweight nature and compliance. Their ability to produce smooth and adaptable motions is particularly beneficial in applications requiring natural and human-like movement, such as rehabilitation and assistive devices. Although PAMs powered control systems face challenges with nonlinear phenomena, their biologically inspired design holds promise for future applications across various industries. These may include innovative applicability in industrial, automotive, and aerospace sectors, as well as use in sports, medical aids, entertainment, and animatronics. Incorporating self-made laboratory systems actuated by PAMs into control systems education offers a comprehensive learning opportunity that combines theoretical concepts with hands-on experience. This approach develops the necessary skills of future engineers, expanding their understanding of technical principles and preparing them for future challenges in engineering practice.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Intelligent fault diagnosis techniques have replaced the time-consuming and unreliable human analysis, increasing the efficiency of fault diagnosis. Deep learning model can improve the accuracy of intelligent fault diagnosis with the help of its multilayer nonlinear mapping ability. This paper has proposed a novel method named Deep Convolutional Neural Networks with Wide First-layer Kernels (WDCNN). The proposed method uses raw vibration signals as input (data augmentation is used to generate more inputs), and uses the wide kernels in first convolutional layer for extracting feature and suppressing high frequency noise. Small convolutional kernels in the preceding layers are used for multilayer nonlinear mapping. AdaBN is implemented to improve the domain adaptation ability of the model. The proposed model addresses the problem that currently, the accuracy of CNN applied to fault diagnosis is not very high. WDCNN can not only achieve 100% classification accuracy on normal signals, but also outperform state of the art DNN model which is based on frequency features under different working load and noisy environment.

Methane is the main cause of sewer explosion accidents, and the available monitoring methods mainly use portable gas sensors for on-site detection. However, these methods cannot grasp the dynamic changes in methane in a sewer in real time or make better predictions of methane explosion accidents. Here, we present a low-power online monitoring system for sewer methane in order to ensure the safety of urban sewers. A low-power ultrasonic gas sensor was used to monitor the methane content in biogas. Due to the impacts of changes in CO2, temperature, and humidity in the sewer on the ultrasonic methane measurement results, a corresponding compensation method was proposed. The effectiveness of the compensation method was verified through experiments, which measured the methane concentration under different influences, and the methane values measured before and after compensation were compared. The power consumption was only 1.28 mW if the system worked in intermittent operation mode, and it could operate for about 1.5 years by selecting a lithium battery with a capacity of 5 A · H. The experimental results showed that the gas detection accuracy could meet the commercial requirements and had a high compensation for the impacts of carbon dioxide, temperature, and humidity.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

The insufficient flexibility of the hybrid renewable integrated energy system (HRIES) makes it difficult to accommodate renewable energy with a high proportion. It is thus necessary to excavate its potential flexibility to improve its operational performance and consume renewable energy. This paper unlocks the adjustment potential of flexible buildings and builds a flexible thermal load regulation model according to the dynamic thermal characteristics and thermal comfort elastic interval of the buildings and a regulation model of the flexible electrical load based on its transferability, resectability, and rigidity. An operation optimization model, which incorporates multiple flexible load regulations and the variable load of devices, is then developed. A case study is presented to analyze the regulation and synergy mechanism in different types of flexible loads. Its results show a saturation effect between the flexible thermal and electrical loads in increasing renewable energy consumption and a synergy effect in decreasing the total cost. This synergy can reduce the total cost by 0.73%. Besides, the total cost can be reduced by 15.13%, and the renewable energy curtailment rate can decrease by 12.08% if the flexible electric and thermal loads are integrated into the operation optimization of HRIES.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

The increased adoption of information and communication technology for smart grid applications will require innovative cyber-physical system (CPS) testbeds to support research and education in the field. The groundbreaking CPS testbeds with realistic and scalable platforms have progressively gained interest in recent years, with electric power flowing in the physical layer and information flowing in the network layer. However, CPSs are critical infrastructures and not designed for testing or direct training, as any misbehaving in an actual system operation could cause a catastrophic impact on its operation. Based on that, it is not easy to efficiently train professionals in CPSs. Aiming to support the advancement and encourage the training of industry professionals, this paper proposes and develops a complete testbed with commercial tools. The testbed can reliably replicate the performance of smart grid systems and the main potential cyber threats that electric grids may face. The complex interdependencies between the cyber and physical domains are discussed in detail, and different case scenarios are presented, providing insightful guidelines for key features and design decisions for future smart grid testbeds.

This paper aims to develop a hierarchical risk assessment model using the newly-developed evidential reasoning (ER) rule, which constitutes a generic conjunctive probabilistic reasoning process. In this paper, we first provide a brief introduction to the basics of the ER rule and emphasize the strengths for representing and aggregating uncertain information from multiple experts and sources. Further, we discuss the key steps of developing the hierarchical risk assessment framework systematically, including (1) formulation of risk assessment hierarchy, (2) representation of both qualitative and quantitative information, (3) elicitation of attribute weights and information reliabilities, (4) aggregation of assessment information using the ER rule and (5) quantification and ranking of risks using utility-based transformation. The proposed hierarchical risk assessment framework can potentially be implemented to various complex and uncertain systems. A case study on the fire/explosion risk assessment of marine vessels demonstrates the applicability of the proposed risk assessment model.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

This study investigates the long-term stability of the Suomi National Polar-orbiting Partnership (S-NPP) Visible Infrared Imaging Radiometer Suite (VIIRS) moderate-resolution Thermal Emissive Bands (M TEBs; M12 – M16) covering a period from February 2012 to August 2020. It also assesses inter-sensor consistency of the VIIRS M TEBs among three satellites-S-NPP, NOAA-20, and NOAA-21 over eight months spanning from March 18 to November 30, 2023. The field of interesting is limited to the ocean surface between 60°S and 60°N, specifically under clear-sky conditions. Taking radiative transfer modeling (RTM) as the transfer reference, we employed the Community Radiative Transfer Model (CRTM) to simulate VIIRS TEB brightness temperature (BTs), incorporating European Centre for Medium-range Weather Forecasts (ECMWF) reanalysis data as inputs. Our results reveal two key findings. Firstly, the reprocessed S-NPP VIIRS TEBs exhibit a robust long-term stability, as demonstrated through analyses of the observation minus background BT differences (O-B ∆BTs) between VIIRS measurements (O) and CRTM simulations (B). The drifts of the O-B BT differences are consistently less than 0.105 K/Decade across all S-NPP VIIRS M TEB bands. Notably, observations from VIIRS M14 and M16 stand out with drifts well within 0.04 K/Decade, reinforcing their exceptional reliability for climate change studies. Secondly, excellent inter-sensor consistency among these three VIIRS instruments is confirmed through the double-difference analysis method (O-O). This method relies on the O-B BT differences obtained from daily data. The mean inter-VIIRS O-O BT differences remain within 0.08 K for all M TEBs, except for M13. Even in the case of M13, the O-O BT differences between NOAA-21 and NOAA-20/S-NPP have values of 0.312 K and 0.234 K, respectively, which are comparable to the 0.2 K difference between some TEBs among VIIRS and MODIS. These disparities are primarily attributed to the significant differences in the Spectral Response Function (SRF) of NOAA-21 compared to NOAA-20 and S-NPP. Our study confirms the RTM-based TEB quality evaluation method’s versatility and effectiveness in assessing long-term sensor stability and inter-sensor consistency. The double-difference approach effectively mitigates uncertainties and biases inherent to CRTM simulations, establishing itself a robust mechanism for assessing inter-sensor consistency. In addition, we’ve observed that, except for M13, M12 always exhibits larger spatial variations of O-O BT differences with greater uncertainties compared to the other M TEBs. The influence of solar contribution through sea surface reflection on the Top of Atmosphere (TOA) radiance measurements during daytime in M12 should not be underestimated.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

This study presents a cost-effective IoT-based remote monitoring system for solar PV energy systems, along with a machine learning-based PV power estimator. Remote access is crucial for tracking PV systems installed in remote areas. In this system, an open-source and IoT-compatible data logger is employed. The data logger collects important performance data of the PV system and transfers it to a server. Real-time visualization of this data is displayed in the designed web and mobile monitoring interfaces. The measured data includes the current, voltage, and temperature information of the PV generator and battery, as well as environmental parameters such as temperature, radiation, humidity, and pressure. Subsequently, this data is used for PV power estimation using machine learning methods. This enables the identification of maintenance requirements and the prediction of potential issues in the PV system. When a problem occurs in the PV system, the user is alerted through the mobile application. Early detection and intervention prevent power loss and damage to system components. When comparing the results of linear regression, SVM, decision trees, random forests, and KNN machine learning methods for power estimation based on performance evaluation criteria, it was observed that the random forests algorithm provided the best results. In conclusion, the developed monitoring and estimation system, along with web and mobile interfaces, is suitable for large-scale PV energy systems.

Utilization of wasted heat instead of fuel combustion is effective to reduce primary energy consumption for mitigating global warming problem. Because wasted heat sources are not necessarily located close to areas of heat demand, one of the difficulties is that wasted heat has to be transferred from heat source side to heat demand side, which may require heat transportation over long distance. From this point we proposed and have examined new idea of heat transportation using ammonia-water as the working fluid which system is named Solution Transportation Absorption chiller, in short STA. Our previous studies of STA were mainly the experimental investigation with STA facility which cooling power was 25RT (90kW). As a result, the COP of STA was found almost same value 0.65 with the conventional absorption chiller without depending on the transportation distances. The simulation using AspenHYSYS also examined with same experimental condition. The experimental data showed good agreement with the simulation calculation. In this study, we examined the large-scale cooling power STA on simulation. The examination cooling powers were from 90 kW(25RT) to 3517 kW(1000RT). All cooling power achieved around COP 0.64 including pump power consumptions. In addition, we performed the dynamic simulation. As the results, there was no effect of pipeline size on the cooling capacities and mass flow rates. Furthermore, the stability time of the cooling capacities and mass flow rates were almost same regardless of the pipeline size and cooling capacity. In other words, STA may be achieved the same COP even though having various complex conditions compared with the conventional absorption chiller.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

The real systems are often complex, nonlinear, and noisy in various areas including mathematics, natural science, and social science. We present the symplectic entropy (SymEn) measure as well as an analysis method based on SymEn to estimate the nonlinearity of the complex system by analyzing the given time series. The SymEn estimation is a kind of entropy based on symplectic principal component analysis (SPCA) which represent organized but unpredictable behaviors of systems. The key to SPCA is to preserve the global submanifold geometrical properties of the systems through symplectic transform in the phase space, which is a kind of the measure-preserving transforms. The capability of preserving the global geometrical characteristics makes the SymEn a test statistic to detect the nonlinear characteristics in several typical chaotic time series and the stochastic characteristic in the Gaussian white noise. The results are in agreement with findings in the approximate entropy (ApEn), the sample entropy (SampEn) and the fuzzy entropy (FuzzyEn). Moreover, the SymEn method is also used to analyze the nonlinearities of the real signals (including the EEG signals for ASD and healthy subjects, and the sound and vibration signals for the mechanical systems). The results indicate that the SymEn estimation can be taken as a measure for describing the nonlinear characteristics in the data collected from the natural complex systems.

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

An off-grid solar energy storage system (ESS) in National Pingtung University of Science and Technology (NPUST) was built and officially operated on Jun. 16th 2022. The system is installed in a 40' general container with PV panels of solar power 8250 W_p on top of the container. The ESS is made by repurposed lithium iron phosphate (LFP) batteries of 20 kWh capacity, where a battery management system (BMS) is adopted to ensured the safety of the battery system. An energy management system (EMS) is built to receive, process, analyse, store, and output the energy information. In this manuscript, a brief engineering report about the system is given.

This study explores optimizing Synthetic Aperture Radar (SAR) satellite constellation scheduling for multi-imaging missions in densely targeted areas using an in-house developed Modified Dynamic Programming (MDP) algorithm. By employing Mixed-Integer Linear Programming (MILP) to define the mission planning problem, the research aims to maximize observation of high-value targets within restricted planning horizons. Numerical simulations, covering a wide range of target numbers and satellite configurations, reveal the MDP algorithm’s superior mission allocation efficiency, enhanced success rates, and reduced revisit times, compared to the Greedy algorithm. The findings underscore the MDP algorithm’s improved operational efficiency and planning robustness for complex imaging tasks, demonstrating significant advancements over traditional approaches.

Aiming at the limitations of single-functionality, limited applicability, and complex designs prevalent in current metasurfaces, we propose a terahertz multifunctional and multiband tunable metasurface utilizing a VO2-metal hybrid structure. This metasurface structure comprises a top VO2-metal resonance layer, a middle polyimide dielectric layer, and a gold film reflective layer at the bottom. This metasurface exhibits multifunctionality, operating independently of polarization and incident angle. The varying conductivity states of the VO2 layers, enable the metasurface to achieve various terahertz functionalities, including single-band absorption, broadband THz absorption, and multiband perfect polarization conversion for linear (LP) and circularly polarized (CP) incident waves. Finally, we believe that the functional adaptability of the proposed metasurface expands the repertoire of options available for future terahertz device designs.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

The availability of current land cover and land use (LCLU) information for monitoring the status of land resources has considerable value in ensuring sustainable land use planning. Similarly, the need to provide updated information on the extent of LCLU change in West Africa has become apparent, given the increasing demand for land resources driven by the rapid population growth in the sub-region. SERVIR West Africa, a regional consortium jointly supported by USAID and NASA to foster the use of geospatial and earth observation data and science for decision-making on critical environmental and food security challenges, in collaboration with the Food and Agriculture Organization of the United Nations (FAO), is building technical capacity in the sub-region to develop and implement harmonized regional land cover classification system for LULC change monitoring in West Africa, based on the Land Cover Meta Language (LCML-ISO 19144-2). This article focuses on the process, potential opportunities, outputs of this collaboration, exemplary use cases, and recommendations for the next steps.

This paper explores the capability of various machine learning algorithms, including Random Forests and advanced gradient boosting techniques such as XGBoost, LightGBM, and CatBoost, to predict customer churn in the telecommunications sector. For this analysis, a dataset available to the public was employed. The performance of these algorithms was assessed using recognized metrics, including Accuracy, Precision, Recall, F1-score, and the Receiver Operating Characteristic Area Under Curve (ROC AUC). These metrics were evaluated at different phases: subsequent to data preprocessing and feature selection; following the application of SMOTE and ADASYN sampling methods; and after conducting hyperparameter tuning on the data that had been adjusted by SMOTE and ADASYN. The outcomes underscore the notable efficiency of upsampling techniques such as SMOTE and ADASYN in addressing the imbalance inherent in customer churn prediction. Notably, the application of random grid search for hyperparameter optimization did not significantly alter the results, which remained comparatively unchanged. The algorithms' performance post- ADASYN application marginally surpassed that observed after SMOTE application. Remarkably, LightGBM achieved an exceptional F1-score of 89% and an ROC AUC of 95% subsequent to the ADASYN sampling technique. This underlines the effectiveness of advanced boosting algorithms and upsampling methods like SMOTE and ADASYN in navigating the complexities of imbalanced datasets and intricate feature interdependencies.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

There is currently no cure for HIV infection although adherence to effective antiretroviral therapy (ART) suppresses replication of the virus in blood, increases CD4+ T-cell counts, reverses immunodeficiency, and increases life expectancy. Despite these substantial advances, ART is a lifelong treatment for people with HIV (PWH) and upon cessation or interruption, the virus quickly rebounds in plasma and anatomic sites including the central nervous system (CNS), resulting in disease progression. With recent advances in quantifying viral burden, detection of genetically intact viral genomes, and isolation of replication-competent virus from brain tissues of PWH receiving ART, it has become apparent that the CNS viral reservoir (largely comprised of macrophage type cells) poses a substantial challenge for HIV cure strategies. Other obstacles impacting the cure of HIV include ageing populations, substance use, comorbidities, limited antiretroviral drug efficacy in CNS cells and ART-associated neurotoxicity. Herein, we review recent findings including studies of the proviral integration sites, reservoir decay rates, and new treatment/prevention strategies in the context of the CNS, together with highlighting the next steps for investigations of the CNS as a viral reservoir.

One of the most crucial elements in deeply understanding humans on a psychological level is manifested through facial expressions. The analysis of a human behavior can be informed by their facial expressions, making it essential to employ indicators such as expression (Expr), valence-arousal (VA), and action units (AU). In this paper, we introduce the method proposed in the Challenge of the 6th Workshop and Competition on Affective Behavior Analysis in-the-wild (ABAW) at CVPR 2024. Our proposed method utilizes the multi-modal Aff-wild2 dataset, which is splitted into spatial and audio modalities. For the spatial data, we extract features using a SimMiM model that was pre-trained on a diverse set of facial expression data. For the audio data, we extract features using a WAV2VEC model. To fusion the extracted spatial and audio features, we employed the cascaded cross-attention mechanism of a transformer.

We are living in a world where people always strive for the luxuries they can get with less hard work and for these smart systems are developed and established all over the world to make life easier for the people. However, in Pakistan being a third-world country we are unable to achieve better results due to the lack of proper transit from one area to another. Sometimes the roads are not in their optimum conditions and hence people have to face a lot of problems while traveling. In urban areas, people cannot reach their destination in time, in some cases, they damage their vehicles due to the cracks on the roads, in medical emergency patient dies most of the time in their transit from rescuing point to the hospital. Similarly, in rural areas where farmers face countless problems while bringing their yield of the season towards the markets. Therefore, having described the severe damage the bad quality of roads is making. A solution is proposed to solve the problems of both the rural and urban population in our project. The project aims to provide the solution to their problem to a certain extent by monitoring the conditions of the roads. The sensors in the system will calculate the values and send them to the cloud server. The cloud server used is the blynk platform where the data will be stored. Moreover, data can be provided to the government in the future for the timely maintenance of the roads, and hence the citizens and lifestyle of the people will be changed. It is expected that the problems of both urban and rural population will be solved to a greater percentage.

Abstract: This study investigates the transition to sustainable shipping industry within the framework of the IMO's 2050 carbon neutrality objective, focusing on socio-technical systems analysis. The research delves into the sustainable paradigm shift towards alternative marine fuels such as LNG, methanol, ammonia, and hydrogen from a socio-technical transition perspective, analyzing the multi-level per-spective challenges and opportunities. Specifically, it scrutinizes the implications of adopting these al-ternative fuels for global shipping, identifying technical uncertainties, financial constraints, and infra-structure needs. Through a comprehensive review of existing literature on ship emissions and alterna-tive fuels, coupled with socio-technical transition theory, the study addresses the multifaceted chal-lenges and opportunities in meeting the IMO's environmental objectives. It emphasizes the necessity of collaborative governance, innovative niche strategies, and a holistic approach to leverage the current window of opportunity in facilitating the maritime industry's transition to sustainable fuel options. Fi-nally, this research enhances our understanding of the intricate interplay between technological, social, industrial, and cultural dynamics in the greening of shipping and offers insights into the strategic adop-tion of environmentally friendly marine fuels for a sustainable future.

Sarcopenia is associated with clinical complications, which increase mortality. Effective sarcopenia risk screening in the elderly should be grounded in a comprehensive assessment, encompassing both nutritional status and medication use. Current screening tools, while emphasizing muscular per-formance, exhibit limited sensitivity in identifying elderly individuals at risk of sarcopenia. This cross-sectional study aimed to develop a sarcopenia risk screening tool, named Sarc-Global, with enhanced sensitivity, incorporating factors pertinent to the overall health of the elderly. Utilizing the criteria established by EWGSOP2 for diagnosing sarcopenia, we evaluated 395 communi-ty-dwelling elderly individuals. This evaluation served as a reference for assessing the efficacy of two validated questionnaires, Sarc-F and Sarc-CalF, and our newly developed Sarc-Global. Con-structed through multiple logistic regression, Sarc-Global integrates variables such as sex, age, medication use, body mass index, arm circumference, and handgrip strength – all significantly associated with sarcopenia (p

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Prostate cancer is the second leading cause of death in males in America, with advanced prostate cancers exhibiting a 5-year survival rate of only 32%. Castration-resistance is often developed during the course of treatment, though its influences require further understanding. This study explores the human microbiome for its implications in castration-resistance and metastasis in prostate cancer. RNA sequencing data was downloaded for bone and soft tissue biopsies of patients with metastatic castration-resistant prostate cancer. These sequences were mapped to bacterial sequences to yield species-level abundance approximations. Numerous species were found to correlate to the expression of known markers of castration-resistance, including AR, PI3K, and AKT. Castration-resistance-associated signaling pathways were also enriched with these species, including PI3K-AKT signaling and endocrine resistance. For their implications in cancer aggression and metastasis, cancer stem cell markers were further explored for relation to these species. EGFR and SLC3A2 were widely downregulated with greater abundance of most species. Our results suggest that the microbiome is heavily associated with castration-resistance and stemness in prostate cancer. By considering the microbiome’s importance in these factors, we may better understand the highly aggressive and highly invasive nature of prostate cancer, allowing for needed improvement in the treatment of this disease.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

Manual traffic surveillance can be a daunting task as Traffic Management Centers operate a myriad of cameras installed over a network. Injecting some level of automation could help lighten the workload of human operators performing manual surveillance and facilitate making proactive decisions which would reduce the impact of incidents and recurring congestion on roadways. This article presents a novel approach to automatically monitor real time traffic footage using deep convolutional neural networks and a stand-alone graphical user interface. The authors describe the results of research received in the process of developing models that serve as an integrated framework for an artificial intelligence enabled traffic monitoring system. The proposed system deploys several state-of-the-art deep learning algorithms to automate different traffic monitoring needs. Taking advantage of a large database of annotated video surveillance data, deep learning-based models are trained to detect queues, track stationary vehicles, and tabulate vehicle counts. A pixel-level segmentation approach is applied to detect traffic queues and predict severity. Real-time object detection algorithms coupled with different tracking systems are deployed to automatically detect stranded vehicles as well as perform vehicular counts. At each stages of development, interesting experimental results are presented to demonstrate the effectiveness of the proposed system. Overall, the results demonstrate that the proposed framework performs satisfactorily under varied conditions without being immensely impacted by environmental hazards such as blurry camera views, low illumination, rain, or snow.

This research investigates the complex transformation of the Baltic Clean and Dirty Tankers markets from 1998 to 2023. Our study quantifies the market multifractality in two distinct periods, from 1998 to 2010 and 2010 to 2023. We compare multifractal measures of the original, surrogated, and shuffled data, which indicate high multifractality and a complex market structure influenced by temporal organization and inherent volatility. Shuffled data analysis emphasizes the critical role of temporal sequences within market behaviour. Additionally, the study delves into external factors such as regulatory changes, economic disturbances, technological innovation, and environmental concerns contributing to market complexity. A distinct shift in multifractal values between the two periods suggests an evolution from crisis-induced complexities to a market influenced by diversified and modern dynamics. Our findings offer a concise understanding of the multifractal nature of the tanker markets and how global crises can impact the markets, emphasizing the importance of considering systemic risks in freight market analysis.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Background and Objectives: In this current state, Type 2 Diabetes Mellitus (T2DM) is more prevalent in the population, and metformin is used as a first-line medication for treating it. There was up surge in the utilization of alternative therapies in the management of diabetes. Especially in diabetes, Herbal medicines are considered safe and reliable by majority of the population. Aim: The purpose of this research is aimed to estimate the safety and efficacy of Polyherbal Metabolite Compounds (PHMC) capsules in adults with T2DM. Materials and Methods: In this study, 60 T2DM patients aged 18-60 years were randomly assigned to Groups A (30) receiving Metformin 500 mg twice a day after food and Group B (30) receiving PHMC capsule 500 mg twice a day after food in a prospective, randomized and open-label clinical study. The in-silico simulation study was performed to selected plants major compounds on target protein Insulin-like Growth Factor-1 (1K3A). Result: The PHMC is found to be safe and effective in the management of T2DM. The FBS, PPBS and HbA1c were significantly lowered (p

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

Multi-view stereo (MVS) employs multi-point photography for image point positioning and three-dimensional reconstruction technology. Recently, this technology has been introduced into the monitoring of road slopes due to advances in photography and computing technology. In general, the various phases of post-image processing procedures are applied to various photographic data. In this study a novel, automated image-monitoring system is proposed to improve the ability of automatic processing. First, an Internet of things (IoT)-based digital photography system architecture was constructed to provide automatic control of camera photography and real-time transmission of image data. In addition, a visual SfM-MVS 3D reconstruction technique was used to develop related software and hardware interfaces based on the built-in Python computing framework of Photoscan Pro. The software integrates fully automatic photography, image transmission, monitoring of data processing and product release programs. The experimental results show that the system architecture can be applied to fully automatic three-dimensional monitoring of road slopes.

Since the creation of the first parallel electrical power systems around the world, the rotor angle stability of synchronously operating generators has been one of the most crucial and challenging problems. In modern electricity networks, involving Kazakhstani, where the renewable energy technologies are rapidly penetrating, and the issue of stability takes on even greater importance due to the technical shortcomings of inverter-based generation. In this framework, an analysis of rotor angle transient stability was carried out when replacing existing synchronous generators with doubly fed induction generators under a certain pre-emergency mode. A critical proportion of active power generation by DFIG units was identified at which transient stability can still be maintained due to the sufficient stored kinetic energy of the synchronous machines remaining in operation. In addition, 2 simple solutions were investigated to improve transient stability, such as an increased time of the automatic reclosure operation and the use of special load shedding automation. For the analysis, a real power system of Mangystau region in Kazakhstan was considered, and the PowerWorld software was used.

The growing integration of renewable energy sources (RES) into the power system causes congestion to occur more frequently. In order to reduce congestion in the short term and to make the utilization of the power system more efficient in the long term, power flow control (PFC) in the transmission system has been proposed. However, exemplary studies show that congestion will increase also in the distribution system if the transmission system is expanded. For this reason, the potential of PFC to reduce congestion in a model of a real 110 kV distribution system is investigated. Several Unified Power Flow Controller (UPFC) devices are optimized in terms of their number and placement in the power system, their size, control parameters, and costs, by using a Parallel Tempering approach as well as a greedy algorithm. Two optimization variants are considered, one reducing the number of degrees of freedom by integrating system knowledge while the other is not. We find that near a critical grid state and disregarding costs, PFC can reduce congestion significantly (99.13 %). When costs of the UPFCs are taken into account, PFC can reduce congestion by 73.2 %. A basic economic analysis of the costs reveals that the usage of UPFCs is profitable. Furthermore, it is found that the reduction of the solution space of the optimization problem leads to better results faster and that, contrary to expectations, the optimization problem is simple to solve. The developed methods allow not only for the determination of the optimal use of UPFCs to minimize congestion, but also to estimate their profitability.

Large power transformers are generally associated with a maximum capacity rating of 100 MVA or higher. These large liquid dielectric power transformers are a custom-built piece of equipment, thus very expensive, and a backbone element of the power grid. In extreme cases as, for example, severe geomagnetic disturbances, permanently monitoring their condition will enhance their electrical reliability and resilience to guarantee efficient management of its life cycle. However, some traditional monitoring/diagnosis techniques have singular features when applied to large power transformers and their interlinked subsystems. In this context, and since that information is hardly put in evidence and compiled in the literature, this paper reviews the particularities of monitoring and diagnosing those assets.

One of the tools for optimal crop production is regular monitoring and assessment of crops. During the growing season of fruit trees, the bloom period has increased photosynthetic rates that correlate with the fruiting process. This paper presents the development of an image processing algorithm to detect peach blossoms on trees. Images of an experimental peach orchard were acquired from the Parma Research and Extension Center of the University of Idaho using an off-the-shelf unmanned aerial system (UAS), equipped with a multispectral camera (Near-infrared, Green, Blue). The orchard has different stone fruit varieties and different plant training system. Individual tree images (high-resolution) and arrays of trees images (low-resolution) were acquired to evaluate the detection capability. The image processing algorithm was based on different vegetation indices. Initial results showed that the image processing algorithm could detect peach blossoms and demonstrate good potential as a monitoring tool for orchard management.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

Food systems will need to undergo considerable transformation. To be better prepared for and resilient to uncertainty and disturbances in the future, resource users and managers need to further develop knowledge about the food and farming system, with its dominating feedback structures and complexities, and to test robust and integrated system-based solutions. This paper investigates how participatory system dynamics modeling can be adapted to groups at the community level with low or no formal educational background. The paper also analyzes the refinement of workshop participants’ mental models as a consequence of a participatory system dynamics intervention. For this purpose, we ran two workshops with small-scale farmers in Zambia. Analysis of workshop data and post-workshop interviews shows that participatory system dynamics is well adaptable to support an audience-specific learning-by-doing approach. The use of pictures, objects and water glasses in combination with the basic aspects of causal loop diagramming makes for a well-balanced toolbox. Participants acquire understanding that is also relevant beyond systems thinking in that is offers a range of practical insights such as a critical evaluation of common food security strategies.

Aiming at the difficult problem of broadband oscillation localization in power systems, the intel-ligent localization method of oscillation source based on the digital twin is proposed and the os-cillation source localization system based on the digital twin is constructed. Firstly, a digital twin-based oscillation source localization method and system architecture are proposed. Fur-thermore, an intelligent positioning method of oscillation source based on data-driven and mechanism fusion is proposed. It includes three steps: oscillation signal preprocessing, oscillation modal analysis and oscillation source localization. For the oscillation signal preprocessing, the generative adversarial imputation network is used to repair the missing samples, and the su-per-resolution technique is used to realize the super-resolution measurement of broadband os-cillation. In the oscillation modal analysis, the spectrum of the oscillation signal is extracted using the fast Fourier transform. To accurately locate the oscillation source, the branch potential energy is used as input to the data-driven model, such as LSTM and CNN. Finally, an oscillation source localization system is developed based on the digital twin workshop CloudPSS-XStudio, which can locate the oscillation source quickly and accurately.

In the early decades of the 19th century, the deaf population in the eastern US and Canada was distributed across a vast area. After the 1817 founding of the American School for the Deaf (ASD) in Hartford, CT and the subsequent establishment of schools for the deaf in New York City (NYSD), Philadelphia, and many other US states, hundreds of deaf students called these schools home for several years. After leaving school, the early American Deaf community faced a challenge: How would the community maintain its social and linguistic ties across a vast geographical area once community members had dispersed to their hometowns? In this paper we analyze the attendance registries of two large gatherings of deaf individuals in Hartford in the years 1850 and 1854. These were among the largest and earliest known gatherings of deaf adults. The demographic data included in these registries open a window onto the evolving American Deaf community of the mid-19th century. Our analyses of the attendees’ school affiliations, ages, and marital status show that the signing community that had taken root among students at schools in Hartford and New York persisted among the adult graduates of those schools in towns across the northeastern US. We compare the places of residence of ASD and NYSD alumni in 1850 and 1854 to their hometowns when they first enrolled at school. Our comparisons suggest the mid-19th-century signing community had become more urban; it was centered to a greater extent in populous cities such as New York, Boston, and Hartford than had been true when the attendees had enrolled in school. We consider how the geography of deafness in the 19th century might inform our understanding of the sources of regional variation in ASL. We also consider how early cross-regional interactions may have inhibited such regional variation.

The hump feature is one of the major instabilities in pump-turbines. When pump-turbines operate in the hump region, strong noise and serious fluctuations can be observed, which are harmful to their safe and stable operation and can even destroy the whole unit as well as water conveyance system. In this paper, a low specific speed (n_q = 36.1 min⁻¹) pump-turbine model was experimentally investigated. Firstly, the hump characteristic was obtained under 19 mm guide vane opening conditions. More interestingly, when the hump characteristic was measured in two directions (increasing and decreasing the discharge), characteristic hysteresis was found in the hump region. The analysis of performance characteristics reveals that the hump instability is the result of Euler momentum and hydraulic losses, and different Euler momentum and hydraulic losses in the two development processes lead to the hysteresis phenomenon. Then, 12 pressure sensors were mounted in the different parts of the pump-turbine model to obtain the time and frequency characteristics. The analysis of the corresponding fast Fourier transform confirms that the hump characteristic is related to low-frequency (0.04–0.15 times rotational frequency) vortices. The occurrence and cessation of vortices depend on the operating condition and measurement direction, which contribute to the hysteresis feature. Finally, the type of the low-frequency vortices was analyzed through the cross power spectrum.

This chapter aims to construct a relatively complete, universal, and highly reliable road surface state monitoring and perception system through the research of the A1 contact road reconstruction project of an international airport (hereinafter referred to as the “airport”). The system design is based on on-the-spot investigation, theoretical analysis, and engineering practice, using vibrating string type and resistive strain sensors as sensing means, real-time high-frequency signal acquisition technology as the guide, 4G router for wireless communication technology as the media, and storage technology for monitoring system based on server storage terminals. In combination with engineering background, aircraft motion state, main landing gear configuration, sensor selection and evaluation, and other major factors, the actual monitoring information needs of the plane are fully taken into account, as well as the difference in sensor information types, and the system design is carried out by stratification and classification.

Severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) persists throughout the world with over 65 million registered cases of survivors with post-COVID-19 sequelae, also known as LongCOVID-19 (LongC). LongC survivors exhibit various symptoms that span multiple organ systems, including the nervous system. To search for neurological biomarkers of LongC, we investigated the soluble proteins present in the plasma and the proteins associated with plasma neuronal-enriched extracellular vesicles (nEVs) in 33 LongC patients with neurological impairment (nLongC), 12 COVID-19 survivors without any LongC symptoms (Cov), and 28 pre-COVID-19 healthy controls (HC). COVID-19 positive participants were infected from 2020-2022, not hospitalized, and were vaccinated or unvaccinated before infection. IL-1b was significantly increased in both nLongC and Cov and IL-8 elevated in only nLongC. Both brain-derived neurotropic factor and cortisol were significantly elevated in nLongC and Cov compared to HC. nEVs from people with nLongC had significantly elevated protein markers of neuronal dysfunction, including amyloid beta 42, pTau181 and TDP-43. This study shows chronic peripheral inflammation with increased stress after COVID-19 infection. Additionally, differentially expressed nEV neurodegenerative proteins were identified in people recovering from COVID-19 regardless of persistent symptoms.

Malaria is a long-standing disease and one of the top life-threatening diseases, yet its treatment has not changed, while the world has already embraced the Fourth Industrial Revolution (4IR). A wave of research on digitizing monitoring mechanisms of such a deadly disease has surfaced. Automated malaria screening is one of the detection processes which are gaining popularity in the research domain. However, the process needs to be coupled with other processes aiming a nationally or regionally contextualised malaria monitoring system. This paper proposes a digital malaria monitoring system in the context of an African country or region. One advantage of such a digital system is that is enables a novel disease spread forecasting model based on the dynamics of different malaria types. The architecture of the diagnosis system is described, and the disease spread model is mathematically modelled in terms of a SPITR (Susceptible- Protected- Infected-Treated- Recovered) epidemic model which is further analysed. The forecasting model is expressed and analysed whereas experiments are conducted using a Monte Carlo simulation method. The design of the monitoring system has inspired how predictions can be made in the complex cases such as mixed infections. Results show that reinforcing the model parameter makes a significant improvement on the disease prediction.

This paper introduces both a hardware and a software system designed to allow low-cost electronic monitoring of social insects using RFID tags. Data formats for individual insect identification and their associated experiment are proposed to facilitate data sharing from experiments conducted with this system. The antenna's configuration and their duty cycle ensure a high degree of detection rates. Other advantages and limitations of this system are discussed in detail in the paper.

Overhead power transmission line icing (PTLI) disasters are one of the most severe dangers to power grid safety. Automatic iced transmission line identification is critical in various fields. However, existing methods primarily focus on the linear characteristics of transmission lines, employing a two-step process involving edge and line detection for PTLI identification. Nonetheless, these traditional methods are often difficult when confronted with challenges such as background noise or variations in illumination, leading to incomplete identification of the target area, missed target regions, or misclassification of background pixels as foreground. We propose a new iced transmission line identification scheme to overcome this limitation. In the initial stage, we integrate the image restoration method with image filter enhancement to restore the image's color information. This combined approach effectively retains valuable information and preserves the original image quality, thereby mitigating noise presented during the image acquisition. Subsequently, in the second stage, we introduce an enhanced multi-threshold algorithm to separate background and target pixels. After image segmentation, we enhance the image and obtain the region of interest (ROI) through connected component labeling modification and mathematical morphology operations, eliminating background regions. Our proposed scheme achieves an accuracy value of 97.72%, a precision value of 96.24%, a recall value of 86.22%, and the specificity value of 99.48% based on the average value of test images. Through object segmentation and location, the proposed method can avoid background interference, effectively solve the problem of transmission line icing identification, and achieve 90% measurement accuracy compared to manual measurement on the collected PTLI dataset.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

Recently, there has been growing interest in using smart eHealth systems to manage asthma. However, limitations still exist in providing smart services and accurate predictions tailored to individual patients’ needs. This study aims to develop an adaptive ubiquitous computing framework that leverages different bio-signals and spatial data to provide personalized asthma attack prediction and safe route recommendations. We proposed a smart eHealth framework consisting of multiple layers that employ telemonitoring application, environmental sensors, and advanced machine-learning algorithms to deliver smart services to the user. The proposed smart eHealth system predicts asthma attacks and uses spatial data to provide a safe route that drives the patient away from any asthma trigger. Additionally, the framework incorporates an adaptation layer that continuously updates the system based on real-time environmental data and daily bio-signals reported by the user. The developed telemonitoring application collected a dataset containing 665 records used to train the prediction models. The testing result demonstrates a remarkable 98% accuracy in predicting asthma attacks with a recall of 96%. The eHealth system was tested online by ten asthma patients, and its accuracy achieved 94% of accuracy and a recall of 95.2% in generating safe routes for asthma patients, ensuring a safer and asthma-trigger-free experience. The test shows that 89% of patients were satisfied with the safer recommended route than their usual one. This research contributes to enhancing the capabilities of smart healthcare systems in managing asthma and improving patient outcomes. The adaptive feature of the proposed eHealth system ensures that the predictions and recommendations remain relevant and personalized to the current conditions and needs of the individual.

Urea cycle disorders (UCDs) are common inborn errors of metabolism, with an incidence of one in 30,000 births. They are caused by deficiencies in any of six enzymes and two carrier proteins, the most common being Ornithine Transcarbamylase Deficiency (OTCD). OTCD results in impairment to excrete nitrogen, causing toxic buildup of ammonia with resultant encephalopathy. Hyperammonemia (HA) induces the conversion of glutamate to glutamine in the brain. Excess glutamine in the brain causes osmotic changes cerebral edema, changes in astrocyte morphology, and cell death. Acute symptoms of HA include vomiting, hyperventilation, seizures, and irritability. Long-term neurological changes include deficits in working memory and executive function. To date, there are no predictors of prognosis of infants with neonatal onset OTCD outside of plasma ammonia level at presentation and duration of hyperammonemic coma. We provide a comprehensive analysis of a 16-year-old male with neonatal onset of OTCD as an example of how brain biomarkers may be useful to monitor disease course and outcome. This male presented at 8 days post natal with plasma ammonia and glutamine of 677 and 4024 micromol/L and had a missense mutation in Exon 4 (p.R129H). Treatment included protein restriction, sodium benzoate, and citrulline, arginine, and iron. He suffered recurrent acute hyperammonemic episodes despite compliance, triggered by infections or catabolic stressors. We discuss the long-term effects of the hyperammonemic episodes by following MRI based disease biomarkers.

Turbidity stands as a crucial indicator for assessing water quality, and while turbidity sensors exist their high cost prohibit their extensive use. In this paper, we introduce an innovative turbidity sensor, and it is the first low-cost turbidity sensor which is designed specifically for long-term stormwater in-field monitoring. Its low cost ($23.50 USD), enables the implementation of high spatial resolution monitoring schemes. The sensor design is available under open hardware and open-source licences, and the 3D-printed sensor housing is free to modify based on different monitoring purposes and ambient conditions. The sensor was tested both in the laboratory and in the field. The laboratory results show a strong linear relationship (R2 > 0.99) between the sensor readings and the commercial hand-held turbidimeter (Thermo Scientific AQ4500) results of the solution. In the field, the low-cost sensor measurements were statistically significantly correlated (p < 0.01) to a standard high-cost commercial turbidity sensor (GreenSpan TS-1000). Biofouling and drifting issues were also analysed after the sensors were deployed in the field for more than 6 months, showing both biofouling and drift occur during monitoring. Nonetheless, in terms of maintenance requirements, the low-cost sensor exhibited similar needs compared to the Green-Span sensor.

We present a custom platform that integrates data from several sensors measuring synchronously different variables of the beehive and wirelessly transmits all measurements to a cloud server. There is a rich literature on beehive monitoring. The choice of our work is not to use ready platforms such as Arduino and Raspberry Pi and to present a low cost and power solution for long term monitoring. We integrate sensors that are not limited to the typical toolbox of beehive monitoring such as gas, vibrations and bee counters. The synchronous sampling of all sensors every 5 minutes allows us to form a multivariable timeseries that serves two-ways: a) it provides immediate alerting in case a measurement exceeds predefined boundaries that are known to characterize a healthy beehive, and b) based on historical data predict future levels that are correlated with hive’s health. Finally, we demonstrate the benefit of using additional regressors in the prediction of the variables of interest. The database, the code and a video of the vibrational activity of two months are made open to the interested readers.

Foundational and state-of-the-art anomaly detection methods through power system state estimation are reviewed. The traditional components for bad data detection such as chi-square testing, residual-based methods, and hypothesis testing are discussed to explain the motivations for recent anomaly detection methods given the increasing complexity of power grids, energy management systems, and cyber-threats. In particular, state estimation anomaly detection based on data-driven quickest change detection and artificial intelligence are discussed and directions for research are suggested with particular emphasis on considerations of the future smart grid.

Using flexible AC transmission system (FACTS) devices in power systems while adhering to some equality and inequality constraints, researchers around the world sought to address this issue with the objectives of improving the voltage profile, reducing power losses in transmission lines, and increasing system reliability and safety. The recent development of FACTS controllers opens up new perspectives for safer and more efficient operation of electrical power networks by continuous and rapid action on power systems parameters, such as phase angle shifting, voltage injection and line impedance compensation. Thus, an improvement on voltage profile and enhancement of power transfer capability can be obtained. It is for that, the idea behind the FACTS concept is to enable the transmission system to be an active element in increasing the flexibility of power transfer requirements and in securing stability of integrated power system. It may also be effective in transient stability improvement, power oscillations damping and balancing power flow in parallel lines. The primary issue that has significantly piqued the interest of a number of researchers working in this field is the FACTS optimization problem, which involves determining the optimal type, location, and size of FACTS devices in electrical power systems. For solving this mixed integer, nonlinear and non-convex optimization problem, this paper provides an in-depth and comprehensive review of the various optimization techniques covered in published works in the field. In this review, a classification of optimization techniques in five main groups that are widely used, such as classical optimization techniques or conventional optimization approaches, Meta heuristic methods, analytic methods or sensitive index methods and mixed or hybrid methods, is summarized. In addition, a performance descriptions and comparison of these different optimization techniques are discussed in this study. Finally, some advice is offered for future research in this field.

Geomagnetic induced current (GIC) is a ground end manifestation associated with the space weather perturbations that should be greatly taken into account by the society. Although the GICs implication to the power system is not regular, it can cause large scale of system failure. In equatorial, the power system is considered safe since the most intense of geomagnetic storm happened in high latitude. However, the internal damage due to GICs which finally led to the South African power system failure has totally changed the normal perception. Therefore, a preliminary investigation on the GICs activity in equatorial region is performed to understand the space weather impact to the power system. Time derivative of the horizontal magnetic field component (dB/dt) is done to indicate the GICs activity value based on Faraday’s law. All the reported power failures are compiled to produce the threshold value of dB/dt, which possibly cause the harmful effect to the system. Then, dB/dt analysis is extended to show the pattern of GICs activity in function of magnetic latitude and local time. The results reveal that power network in equatorial region has possibly suffered by GIC. Plus, high number of intense GIC activity in this region occurred during dayside.

The energy transition towards renewable and more decentral power production triggers the need for grid and storage expansion on all voltage levels. Today's power system planning focuses on certain voltage levels or spatial resolutions. In this work we present an open source software tool eGo which is able to optimize grid and storage expansion throughout all voltage levels in a developed top-down approach. System costs are minimized by applying a linear optimal power flow considering the grid infrastructure of the extra-high and high-voltage (380 to 110 kV) level. Hence, the common differentiation of transmission and distribution grid is partly dissolved, integrating the high-voltage level into the optimization problem. Consecutively, optimized curtailment and storage units are allocated in the medium voltage grid in order to lower medium and low voltage grid expansion needs, that are consequently determined. Here, heuristic optimization methods using the non-linear power flow were developed. Applying the tool on future scenarios we derived cost-efficient grid and storage expansion for all voltage levels in Germany. Due to the integrated approach storage expansion and curtailment can significantly lower grid expansion costs in medium and low voltage grids and at the same time serve the optimal functioning of the overall system. Nevertheless, the cost-reducing effect for the whole of Germany was marginal. Instead, the consideration of realistic, spatially differentiated time series lead to substantial overall savings.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Battery electric vehicles provide an opportunity to balance supply and demand in future power systems with high shares of fluctuating renewable energy. Compared to other storage systems such as pumped-storage hydroelectricity, electric vehicle energy demand is highly dependent on charging and connection choices of vehicle users. We present a model framework of a utility-based stock and flow model, a utility-based microsimulation of charging decisions, and an energy system model including respective interfaces to assess how the representation of battery electric vehicle charging affects energy system optimization results. We then apply the framework to a scenario study for controlled charging of nine million electric vehicles in Germany in 2030. Assuming a respective fleet power demand of 27 TWh, we analyze the difference between power-system-based and vehicle user-based charging decisions in two respective scenarios. Our results show that taking into account vehicle users’ charging and connection decisions significantly decreases the load shifting potential of controlled charging. The analysis of marginal values of equations and variables of the optimization problem yields valuable insights on the importance of specific constraints and optimization variables. In particular, state-of-charge assumptions and representing fast charging drive curtailment of renewable energy feed-in and required gas power plant flexibility. A detailed representation of fleet charge connection is less important. Peak load can be significantly reduced by 5% and 3% in both scenarios, respectively. Shifted load is very robust across sensitivity analyses while other model results such as curtailment are more sensitive to factors such as underlying data years. Analyzing the importance of increased BEV fleet battery availability for power systems with different weather and electricity demand characteristics should be further scrutinized.

With the emergence of Advance Logistics, the logistics industry has witnessed significant advancements, leading to a greater reliance on intelligent technologies. These technologies play a crucial role in gathering and transmitting logistics data, but they also introduce security and privacy risks to logistics management systems. The sharing of customer-sensitive information among stakeholders for efficient operations becomes vulnerable to unauthorized access, thus compromising privacy. This, amongst others, is a critical problem that needs to be addressed. The unique features of a cryptographic hash function, including immutability, efficient verification, and anonymity, make it a transformative technology that has the potential to address the mentioned challenges in various sectors. This disruptive technology offers solutions by ensuring data integrity, enabling quick verification, and preserving privacy. The findings suggest that employing Cryptographic Hash Functions to share customer data among logistics partners offers robust protection against cyber-attacks. The proposed system guarantees asset security, and as demonstrated by the case study evaluation, exhibits strong resilience in safeguarding against various security and privacy threats. Although this study is significant, it does have limitations. One of these limitations is the considerable overlap between logistics research and supply chain management (SCM). While our focus was on logistics tasks, we did not extensively delve into the broader context of SCM

Dolichandrone spathacea is a rare and endangered semi-mangrove plant species with an extremely small population, naturally distributed only in Zhanjiang City and the east coast of Hainan Island, China. Regrettably, the present situation of the D. spathacea population in China has not yet been carefully investigated. In this study, we aim to evaluate the current resource status and population dynamic characteristics of D. spathacea on Hainan Island, China, in order to propose sustainable conservation and management strategies for future ecological restoration of its natural population. Our results show that D. spathacea on Hainan Island can be divided into four populations. All the D. spathacea populations present a state of overall dispersion, local concentration, and occasionally sporadic existence, and they exist in geographical isolation. The young, middle, and old D. spathacea plants account for 20.42%, 66.20%, and 13.38%, respectively, indicating that the overall age class of the D. spathacea population on Hainan Island belongs to a declining type. Furthermore, instead of temporal structure, we chose diameter at breast height (DBH) to establish a static life table, draw a population survival curve, and quantify the future development trend through population dynamic analysis and time-series prediction. These results directly point out that the D. spathacea population on Hainan Island is sensitive to external disturbances and possesses two main increases in mortality rate—namely, in its juvenile and mature stages—due to weak vitality, competition, and anthropogenic interferences, which are the most important reasons for its endangered status. Depending on the current conditions of the D. spathacea population, we should conserve and expand mature trees in situ, preserve their germplasm resources, rehabilitate their habitats to promote provenance restoration, and conduct artificial cultivation and spreading planting in order to realize the sustainable conservation and management of D. spathacea.

Ultralight power generation equipment has high requirements for the power density, continuous operation, and transient stability of the whole machine, and there is a direct conflict between high power density design and substantial stability control in the power unit design. In order to meet the power density requirements of ultra-light power stations, three main problems need to be solved, namely engine speed oscillation and flameout in the process of load power mutation, matching of the generator and engine torque, and stabilizing the voltage waveform of the AC output end. In this paper, we proposed an exquisite control strategy for ultralight power generation systems in engines, generators, and inverters. The effectiveness and practicability of the proposed strategy are verified by both simulation and experiment. The results show that the proposed control strategy can effectively solve the instability problem of the ultralights generator set and improve the stability of the system, where the response recovery can be achieved within 0.9 seconds under the condition of total load increase or decrease, and the mismatching degree of the generator following the engine is reduced by 90%. The strategy could also guarantee long-term stable operation with high-quality electrical energy output.