A programmable DC power supply with Real-time Digital Simulator (RTDS)-based photovoltaic (PV) Power Hardware-In-the-Loop (PHIL) simulators have been used to improve the control algorithm and reliability of PV Inverter. This paper proposes a supervisory control algorithm for PV PHIL simulator with non-RTDS device that is an alternative solution of high cost PHIL simulator. However, when such a simulator with conventional algorithm which is used in RTDS is connected to a PV inverter, the output is in the transient state and it makes it impossible to evaluate the performance of the PV Inverter. Therefore proposed algorithm controls the voltage and current target values according to the constant voltage (CV) and constant current (CC) modes to overcome the limitation of the Computing Unit, DC power supply and also uses a multi-rate system to account for the characteristics of each component of simulator. A mathematical models of a PV system, programmable DC power supply, isolated DC measurement device and Computing Unit are integrated to form a real-time processing simulator. Performance tests using a PV PHIL simulator which is applied proposed algorithm connected a PV inverter are carried out and proved superiority and utility of this method against conventional methods.

Nowadays, unmanned vehicles are widely used in various fields. However, the safety of unmanned vehicles is directly determined by the autopilot systems, and sensor faults are a very critical factor that affects the normal operation of the autopilot systems. To efficiently and comprehensively test unmanned systems for sensor faults, this paper proposes a chip-level testing platform for unmanned vehicle autopilot systems based on FPGA hardware-in-the-loop simulation. Unlike existing testing platforms, the introduction of FPGA technology allows us to achieve nanosecond real-time simulation frequency, thus realizing chip-level simulation of sensors and black-box automated testing. Firstly, we propose a set of general platform and modeling methods, and the paper presents a detailed application of the four most common necessary sensors in autopilot systems as examples. Secondly, we propose for the first time a chip-level fault testing method for unmanned systems, and build a test platform with a quadrotor vehicle, the PX4 software platform, and the Pixhawk4 hardware platform as examples. Finally, the experimental results verify that the testing platform proposed in this paper can adapt to various autopilot systems and has high simulation test reliability.

Heating systems such as heat pump and combined heat and power cycle systems (CHP) are representing a key component in the future smart grid. Their capability to couple the electricity and heat sector promises a massive potential to the energy transition. Hence, these systems are continuously studied numerical and experimental to quantify their potential and develop optimal control methods. Although numerical simulations provide time and cost-effective solution for system development and optimization, they are exposed to several uncertainties. Hardware in the loop (HiL) system enables system validation and evaluation under different real-life dynamic constraints and boundary conditions. In this paper, a HiL system of heat pump testbed is presented. This system is used to present two case studies. In the first case, the conventional heat pump testbed operation method is compared to the HiL operation method. Energetic and dynamic analyses are performed to quantify the added value of the HiL and its necessity for dynamics analysis. The second case, the HiL testbed is used to validate the heat pump operation in a single family house participating in a local energy market. It enables not only the dynamics of the heat pump and the space heating circuit to be validated but also the building room temperature. The energetic analysis indicated a deviation of 2% and 5% for heat generation and electricity consumption of the heat pump, respectively. The model dynamics emphasized the model capability to present the dynamics of a real system with a temporal distortion of 3%.

Based on the dynamic strength variation mechanism of concrete under complex loading conditions, two approaches were devised: numerical testing and CT scanning, guided by the principle of minimizing energy dissipation. A methodology for calculating concrete's failure area and measuring its strength was developed. The analysis delves into the mechanisms behind failure patterns and variations in concrete specimen strength, focusing on crack initiation, development, and the resultant failure surface formed by crack propagation, along with the stress distribution in concrete specimens subjected to diverse loading conditions. Through evaluating the strength and computed failure area of concrete specimens, it is evident that the loading method influences both the strength and failure area of concrete specimens. In general, a larger failure area correlates with a higher measured strength.

In the last decade, robotic-mediated rehabilitation has emerged as a potential solution to improve repetitive task training. Each device in this field has a unique development history shaped by engineers’ expertise in specific programming languages or platforms. In this work we adopt an approach that tries to abstract from the final implementation with the aim to make control logic more shareable and understandable. The authors will present the outcomes of the application of a Rapid Control Prototyping strategy to an upper-limb robotic exoskeleton. A model-based design approach implemented on a real-time target machine is presented. This modern design approach was explored with several control strategies and was used to test the exoskeleton’s performances. The proposed method highlights how it is possible to develop the entire control architecture in a single programming environment.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

As the adoption of renewable energy sources grows, ensuring a stable power balance across various time frames has become a central challenge for modern power systems. In line with the "dual carbon" objectives and the seamless integration of renewable energy sources, harnessing the advantages of various energy storage resources and coordinating the operation of long-term and short-term storage have become pivotal directions for future energy storage deployment. To address the complexities arising from the coupling of different time scales in optimizing energy storage capacity, this paper proposes a method for energy storage planning that accounts for power imbalance risks across multiple time scales. Initially, the Seasonal and Trend decomposition using the Loess (STL) decomposition method is utilized to temporally decouple actual operational data. Subsequently, power balance computations are performed based on the obtained data at various time scales to optimize the allocation of different types of energy storage capacities and assess the associated imbalance risks. Finally, the effectiveness of the proposed approach is validated through hourly applications using real-world data from a province in China over recent years.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

Tail-sitters aim to combine the advantages of fixed-wing and rotor-craft, but demand a robust and fast stabilization strategy to perform vertical maneuvers and transitions to and from aerodynamic flight. The research conducted in this work intends to assess the performance of nonlinear control strategies to stabilize the attitude of a X-Vert VTOL aircraft when hovering, comparing existing solutions to applications of Nonlinear Dynamics Inversion (NDI) and its incremental version, INDI. Such controllers are implemented and tuned in simulation in order to stabilize a model of the tail-sitter , complemented by estimation methods that allow to feed back the necessary variables. These estimators and controllers are then implemented in a microcontroller, validating them in a Hardware-in-the-Loop (HITL) scenario, with simple maneuvers in vertical flight. Lastly, the developed control solutions are used to stabilize the aircraft in experimental flight, being monitored by a motion capture system. The experimental results allow to validate the model of the X-Vert and compare the effectiveness of the different control solutions in stabilizing it, with the INDI presenting itself as a more robust control strategy, with better tracking capabilities and less actuator demands.

Wireless communications are gaining massive demand for faster video streaming, virtual reality, and 5G-based IoT (Internet of Things) applications. Due to this network congestion increases hastily. The demand for user-specific services, machine learning, forcing the radio access network (RAN) to provide improvement in utilization of spectrum efficiency, minimizing power consumption, and improving data rate. For LTE/LTE-A network specifications provided by third-generation partnership project (3GPP), guarantees to provide qualitative of service (QoS). Release 15/16 utilizes two-dimensional (2D) active antenna array systems (AAS). This kind of AAS provides beam forming in both azimuth and elevation also termed as Full Dimensional MIMO (FD-MIMO). It enhances the radiation pattern of the antenna array element by adjusting the angular power spectra at the base station (BS), it also allows selecting the minimum number of antennas for effective beam forming toward specific user equipment’s (UEs). Spectrum allocation challenge can be dealt with at mm wave band having FR2 (>6GHz) frequency band specified by International Telecommunication Union (ITU-R) in line with IMT-2020 specifications. The spectrum is free at mm Wave for communication of 5G. However, the main challenge is, it faces path loss and atmospheric loss electromagnetic energy absorbed by gases like oxygen. In this work, the 5G new RAN power spectrum and power delay profile at 10GHz carrier frequency with 20MHz to 100MHz channel bandwidth is observed for line of sight (LOS) and non-line of sight (NLOS) communication for guaranteed QoS. To demonstrate the path loss and power delay profile (PDP) in directional and Omni-directional antennas NYUSIM channel simulator is utilized.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Natural gas hydrate, also known as combustible ice and mainly composed of methane, it is identified as the potential clean energy in the 21th century. Due to its large reserves, gas hydrate can ease problems caused by energy resource shortage and has gained attention around the world. In this paper, we focus on the exploration and development of gas hydrate as well as discussing its status and future development trend in China and abroad, then we analyze its opportunities and challenges in China from four aspects: resource, technology, economy and police with five forces model and PEST method. The results show, China has abundance gas hydrate resource; however the backward technologies and inadequate investment has seriously hindered the future development of gas hydrate, so China should establish relevant cooperation framework and intuitional arrangement to attract more investment as well as breaking through technical difficulties to make gas hydrate commercialization as soon as possible.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Reasonable allocation of production plans and saving the overall electricity cost are crucial for large manufacturing conglomerates, which is an effective way for conglomerates to realize open-source and cost-saving. This paper develops an optimization model of off-site industrial production scheduling for enterprises in response to the problems of high electricity costs due to the irrational allocation of production schedules on the demand side of China's electric power and the difficulty of promoting industrial and commercial distributed photovoltaic (PV) projects in China. The model makes full use of the conditions of different PV resources and different electricity prices in different places to optimize the scheduling of industrial production in different places. The model is embedded with two sub-models of the electricity price prediction model and distributed photovoltaic kWh cost model to complete the model parameters, in which the electricity price prediction model utilizes the LSTM neural network. The integrated model is then solved by the particle swarm algorithm. To verify the effectiveness of the model in solving the problem of off-site production scheduling on the demand side of electricity, the research team researched two off-site pharmaceutical factories belonging to the same large pharmaceutical company. Finally, the research data were substituted into the model for solving, and it was concluded that the optimization model could significantly reduce the cost of electricity consumption of the enterprise by about 7.9 %.

Natural polluted insulator surfaces are always coated with various kinds of soluble constituents, and those constituents affect flashover performance differentially. Currently this fact is not considered either in laboratory experiments or field pollution degree measurements, causing the existing insulation selection method to be deficient. In this paper a systematical research on insulator flashover voltage gradient correction involving types of soluble pollution constituents was presented. Taking typical type glass insulator as the sample, its flashover tests polluted by typical soluble chemicals NaCl, NaNO₃, KNO₃, NH₄NO₃, MgSO₄, Ca(NO₃)₂ and CaSO₄ were carried out. Then the flashover gradient correction was made combining the flashover performance of each soluble constituent, the ESDD contribution of the seven constituents, as well as the saturation performance of CaSO₄. The correction was well verified with the flashover test results of insulator polluted by three types of soluble mixture. Research results indicate that the flashover gradient correction method proposed by this paper performs well in reducing the calculating error. It is recommended to carry out component measurements and flashover gradient correction to better select outdoor insulation configuration.

Accurate forecasting of icing thickness has a great significance for ensuring the security and stability of power grid. In order to improve the forecasting accuracy, this paper proposes an icing forecasting system based on fireworks algorithm and weighted least square support vector machine (W-LSSVM). The method of fireworks algorithm is employed to select the proper input features with the purpose of eliminating the redundant influence. In addition, the aim of W-LSSVM model is to train and test the historical data-set with the selected features. The capability of this proposed icing forecasting model and framework is tested through the simulation experiments using real-world icing data from monitoring center of key laboratory of anti-ice disaster, Hunan, South China. The results show that the proposed W-LSSVM-FA method has a higher prediction accuracy and it may be a promising alternative for icing thickness forecasting.

Single-phase-to-ground fault in non-effectively grounded systems poses serious public safety concern. Along with increasing deployment of low-voltage (LV) sensors, new opportunities and ways are created for solving this traditional problem in distribution systems. A new approach, identifying primary single-phase-to-ground line fault and locating it through measurement data from smart sensors deployed in the secondary side of distribution transformers, is proposed in this paper. When a fault occurs in primary distribution feeder, the transient aerial mode voltage (AMV) of each LV smart sensor is calculated. The fault line can be identified by an abrupt change value of AMV at LV side. Next, by finding the position of the maximum value of this AMV from LV sensors on the fault line, the fault location can be pinpointed to two neighboring distribution transformers. The proposed method has been proven to be efficient and reliable by simulation studies.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

The Active Distribution Networks (ADNs) are Multi-Input Multi-Output (MIMO) systems with coupled dynamics which cause interactions among the control loops of the Distributed Energy Resources (DERs). This undesired effect lead to performance degradation in the voltage control. To mitigate the effects of these unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In details, each DER is equipped with a double loop PI to control the active and reactive powers output by the Voltage Source Converter (VSC) which connects the DER to the network's node. Furthermore, to guarantee Ancillary Services (ASs), the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a two sequential steps procedure based on the (Internal Model Control) IMC technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in presence of model parameter uncertainty in the MIMO model.

With the development of higher voltage power grid, the high and low voltage parallel loops are emerging, which lead to energy losses, even threaten the security and stability of power system. The multi-infeed HVDC configurations widely appearing in AC/DC interconnected power system make this situation even worse. Aimed at energy saving and system security, a decision optimization method for power grid operating condition with high and low voltage parallel loops is proposed in this paper. Firstly, considering hub substation distribution and power grid structure, parallel loop opening schemes are generated with GN algorithm. Then, candidate opening schemes are preliminarily selected from all these generated schemes based on a filtering index. Finally, with the influence on power system security, stability and operation economy in consideration, an evaluation model for candidate opening schemes is founded based on analytic hierarchy process (AHP). And a fuzzy evaluation algorithm is used to find the optimal scheme. Simulation results of New England 39-bus system and an actual power system validate the effectiveness and superiority of this proposed method.

This paper analyzes and compares models for predicting average magnet losses in interior permanent-magnet motors with fractional-slot concentrated windings due to harmonics in the armature reaction (assuming sinusoidal phase currents). Particularly, loss models adopting different formulations and solutions to the Helmholtz equation to solve for the eddy currents are compared to a simpler model relying on an assumed eddy-current distribution. Boundaries in terms of magnet dimensions and angular frequency are identified (numerically and using an identified approximate analytical expression) to aid the machine designer whether the more simple loss model is applicable or not. The assumption of a uniform flux-density variation (used in the loss models) is also investigated for the case of V-shaped and straight interior permanent magnets. Finally, predicted volumetric loss densities are exemplified for combinations of slot and pole numbers common in automotive applications.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

We present an open-source Star Tracker (ST) for Attitude Determination. Our implementation makes use of open source software of common usage in astronomy running on a Raspberry Pi 2 platform. The developed platform is open and available for parties interested in further development. Evaluation of the system showed that the ST is suitable for Cubesats of 2U or larger. The ST platform is capable of solving the Lost-In-Space (LIS) problem. Currently, the average accuracy reached of the algorithm is close to 5 seconds of arc with an average processing time of 75 seconds. However, a average accuracy of about 3 minutes of arc can be reached with 35 seconds in average processing time. We also describe the evaluation procedure, the found conclusions of this procedure, in particular the section of the algorithm where most of the processing time is spent and other possible source of errors not included in this study.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

We suppose that a Cooper pair (CP) will experience a damping force exerted by the condensed matter. A Langevin equation of a CP in two dimensional condensed matter is established. Following a method similar to Nelson's stochastic mechanics, generalized Schr\"{o}dinger equation of a CP in condensed matter is derived. If the CPs move with a constant velocity, then the corresponding direct current (DC) electrical conductivity can be calculated. Therefore, a Drude like formula of resistivity of CPs is derived. We suppose that the damping coefficient of CPs in two dimensional cuprate superconductors is a linear function of temperature. Then the resistivity and scattering rate of CPs turn out to be also linear-in-temperature. The origin of linear-in-temperature resistivity and Planckian dissipation in cuprate superconductors may be the linear temperature dependence of the damping coefficient of CPs.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x104 – 2x107 CFU per ml and has a sensitivity of S = 1.655x105 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10-9 grams (g) which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

The new unique technology for granulation of metals and nonmetallic melts is presented in the paper. It was created on the newly developed controlled film flow disintegration with rapid cooling of the droplets and solidified granules in amorphous state. Three new phenomena discovered by us created the base for 3 different methods for granulation of metals and nonmetallic melts in a wide range of granules’ sizes. Electromagnetic resonance method allows producing granules of metals in the range of 1 mm and over. The soliton-like vibrational regime is available for production of any granulation material in the range 0.1-1 mm. Moreover, the shockwave regime is applicable for producing particles from 10 micrometers by size. All methods produce particles of the stated size with a narrow distribution by size: deviation from the average size no more than 50%. The other known methods do not produce granules with such high cooling rate, which can realize the amorphous state and cannot regulate size of particles in such bright but narrow range from 10 micrometers to 1-2 mm.

Water footprint has been widely used to illustrate the consumption of water in many situations; for instance, in products, processes or regions of interest. In this work, we analyzed – using a sensitivity analysis approach – the effect of some variables in the calculation of the water footprint in the viticulture in Brazilian Serra Gaúcha (the major producing region of Brazilian Wine).The classical Penman-Monteith model for evapotransporation was considered, with uncertainties in some parameters (dead mulch covering fraction in the vineyard, maximum temperatures for some months, altitudes and latitudes of the site). The sensitivity analysis was conducted using the SAFE toolbox under Octave framework. The results indicated that the the portion of the water footprint corresponding to the evapotranspiration is more sensitive to the values of mulch covering fraction and the altitude of the site in comparison with the latitude and the maximum temperatures.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

Solar photovoltaic (PV) generation suffers from multiple serious issues, for example shading effects directly affect the performance of installed PV arrays. By studying these issues, it can play a key role in improving the limitations and performance of PV panels. The study of PV arrays under partial shading conditions is mentioned in many papers as a part of other studies and as an independent phenomenon. Therefore, it is essential to improve these studies and update them with new research and study this problem in detail to know how to limit the effects of partial shading irradiance conditions on PV arrays performances, including economical aspects. This paper proposes to study the effects of different partial shading irradiance conditions for a PV array in various configurations. The analysis is proved in detail through the simulation of the proposed PV array in the Matlab/Simulink environment. The obtained results show the performances of interconnected PV arrays under different partial shading irradiance and temperature conditions, including the solar array I-V and P-V characteristics. In addition, different PV array configurations with and without bypass and blocking protection diodes improve and minimize the effect of partial shading conditions and avoid the reductions in output power.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Probiotic feed additives have attracted considerable research interest in recent years because the effectiveness of probiotics can differ across microbial strains and the supplemented macroorganisms. The present study was conducted on 16 lambs divided into two groups (C - control and E - experimental). The examined lambs were aged 11 days at the beginning of the experiment and 40 days at the end of the experiment. The diet of group E lambs was supplemented with a multi-strain probiotic formulation (Lactobacillus plantarum AMT14, Lactobacillus plantarum AMT4, Lactobacillus rhamnosus AMT15, and Bifidobacterium animalis AMT30), whereas group C lambs did not receive the probiotic additive. At the beginning of the experiment (day 0) and on experimental days 15 and 30, blood was sampled from the jugular vein to determine and compare: phagocytic activity (PHAGOTEST) and oxidative metabolism (PHAGOBURST) of peripheral blood granulocytes and monocytes by flow cytometry. An analysis of the phagocytic activity of granulocytes and monocytes revealed significantly higher levels of phagocytic activity (expressed as the percentage of phagocytic cells and mean fluorescence intensity) in lambs administered the multi-strain probiotic formulation than in the control group. The probiotic feed additive also exerted a positive effect on the oxidative metabolism of both granulocytes and monocytes (expressed as the percentage of oxidative metabolism and mean fluorescence intensity) after stimulation with Escherichia coli bacteria and with PMA (4-phorbol-12-β-myristate-13-acetate).

In order to realize the tram's low-floor structure, most of the trams that have been recently introduced adopt an independently rotating wheelset. In the case of trains driving in two regions with different gauges, an independently rotating wheelset may be applied to utilize the variable track technology. Since the independent rotation type wheelset has no rotational restraint of the left and right wheels, the difference in rotational speed between the outer and inner wheels occurs naturally during curved driving, and it is applied to railroad vehicles traveling in steep curve sections because it smoothly drives curved driving. However, the longitudinal creep force and the lateral restoring force are weakened as the left and right rotational constraints disappear. Lack of transverse direction restoring force weakens stability while causing continuous flange contact driving or zigzag phenomenon against disturbance. Under the conditions of driving in a steep curve, these railway vehicles generate excessive wear, noise, and lateral pressure, as well as deterioration of ride comfort and derailment. In order to overcome these drawbacks, a method has been proposed in which the torque of a motor mounted on each wheel is individually controlled to generate lateral restoring force or to improve driving performance through lateral displacement control using a yaw moment. In this paper, development using HILs was performed to check the performance and stability of the individual motor torque control technology before verifying by applying the individual motor torque control to the actual vehicle. HILs were constructed by combining a real-time dynamic analysis model of a railway vehicle with a drive motor to which real individual motor control was applied. Under the conditions of driving the test track where the actual test vehicle was tested, the analysis of the driving characteristics and the control characteristics of the disturbance was performed to confirm the proposed individual motor torque control performance.

Members of the genus Armillaria are widespread forest pathogens against which effective protection has not yet been developed. Due to their longevity and the creation of large-scale cloning of Armillaria individuals, the use of mycoviruses as biocontrol agents (BCAs) against these pathogens could be an effective alternative. This work describes the screening of double-stranded RNA banding patterns as a first approach for potential virus discovery and the use of stranded total RNA-seq for viral detection and characterization in Armillaria spp. collected in the Czech Republic. A total of five single-stranded RNA viruses were detected in Armillaria ostoyae and A. cepistipes, including the first virus of the family Tymoviridae found infecting a member the genus Armillaria and four viruses belonging to the recently described virus group "ambiviruses" with circular ambisense genome organization. Both hammerhead (HHRz) and hairpin (HpRz) ribozymes were detected in all the ambiviricot sequences. Armillaria viruses were compared by phylogenetic analysis and confirmed their specific host by direct RT-PCR, which showed the occurrence of interspecies transmission.

More and more works are using machine learning techniques while adopting supervisory control and data acquisition (SCADA) system for wind turbine anomaly or failure detection. While parameter selection is important for modelling a wind turbine’s health condition, only a few papers have been published focusing on this issue and in those papers interconnections among sub-components in a wind turbine are used to address this problem. However, merely the interconnections for decision making sometimes is too general to provide a parameter list considering the differences of each SCADA dataset. In this paper, a method is proposed to provide more detailed suggestions on parameter selection based on mutual information. Moreover, after proving that Copula, a multivariate probability distribution for which the marginal probability distribution of each variable is uniform is capable of simplifying the estimation of mutual information, an empirical copula based mutual information estimation method (ECMI) is introduced for an application. After that, a real SCADA dataset is adopted to test the method, and the results show the effectiveness of the ECMI in providing parameter selection suggestions when physical knowledge is not accurate enough.

For offshore wind power generation, accessibility is one of the main factors that has great impact on operation and maintenance due to constraints on weather conditions for marine transportation. This paper presents a framework to explore the accessibility of an offshore site. At first, several maintenance types are defined and taken into account. Next, a data visualization procedure is introduced to provide an insight into the distribution of access periods over time. Then, a rigorous mathematical method based on finite state Markov chain is proposed to assess the accessibility of an offshore site from the maintenance perspective. A five-year weather data of a marine site is used to demonstrate the applicability and the outcomes of the proposed method. The main findings show that the proposed framework is effective in investigating the accessibility for different time scales and is able to catch the patterns of the distribution of the access periods. Moreover, based on the developed Markov chain, the average waiting time for a certain access period can be estimated. With more information on the maintenance of an offshore wind farm, the expected production loss due to time delay can be calculated.

In Brazil, Brazilian borreliosis (BB), characterized molecularly, exhibits symptoms akin to Lyme disease (LD) but presents unique epidemiological, clinical, and morphological features. This study explores the incidence, diagnostic challenges, and awareness initiatives regarding this disease in Brazil. Employing a narrative review methodology, data were sourced from Pubmed, Ebsco, Google Scholar, and Web of Science without temporal constraints. Results reveal diagnostic complexities in Brazil due to the low sensitivity of conventional tests and the use of North American B. burgdorferi antigens. Despite challenges, epidemiological studies indicate an upswing in cases in humans and animals. Therefore, there is an urgent need to define new biomarkers, molecular strategies, or new antigenic targets to advance the development of vaccines and diagnostics. Early and accurate pathogen identification is crucial for active surveillance to comprehend and manage this zoonosis.

Populational aging is marked by chronic non-communicable diseases, such as metabolic syndrome (MetS). IL-10 and IL-1β are pleiotropic cytokines with multiple biological effects linked to metabolic disorders. This cross-sectional study assessed 193 participants' IL-10 and IL-1β serum levels regarding their role in developing MetS, clinical characteristics, and their IL1B rs1143627 and IL10 rs1800890 variants' genotype frequencies in a population over 60. IL-10 levels correlated weakly with HDL levels and fat mass and inversely with triglycerides, glucose, glycated hemoglobin, and estimated average blood glucose levels. IL-10 levels were also indirectly influenced by the patient's T2DM duration, lean mass amount, and bone mineral content. Participants with altered HDL, elevated serum glucose, raised HbA1c levels, or those over 80 had reduced serum IL-10 levels compared to those with normal levels or other age groups, respectively. Women also had higher serum IL-10 levels than men. Dissimilarity, IL-1β levels correlated directly only with the number of total leukocytes and segmented neutrophils, showing only significant variations with self-reported alcohol consumption. Our study also found that those with the IL10 AA genotype (lower IL-10 levels) had a significantly higher risk of developing MetS. These findings may help direct future research and more targeted therapeutic approaches in older adults.

Cancer treatment is a significant focus in medicine owing to the increasing global incidence. Patients with advanced cancers that do not respond to conventional therapies have limited options and an unfavorable prognosis. Consequently, researchers are investigating complementary approaches to conventional treatments. One such approach is alkalization therapy, which aims to neutralize the acidic tumor microenvironment (TME) by increasing its pH level. The acidic TME promotes inflammation, tumor progression, and drug resistance. Alkalization therapy has been demonstrated to be effective for various cancers. In addition, natural products, such as triterpenoids, parthenolides, fulvic acid, Taxus yunnanensis, and apple pectin have the potential to alleviate symptoms, maintain physical fitness, and improve treatment outcomes of cancer patients through their anti-inflammatory, antioxidant, and anticancer properties. In this review, we focus on the effects of alkalization therapy and natural products on cancer. Furthermore, we present a case series of advanced cancer patients who received alkalization therapy and natural products alongside standard treatments, resulting in long-term survival. We posit that alkalization therapy together with the supplementation of natural products may confer benefits to cancer patients by mitigating the side effects of chemotherapy and complementing standard treatments. However, further research is warranted to validate these clinical findings.

Polymer inclusion membranes (PIMs), which contained cellulose tri-acetate used as a polymer base, a plasticizer in the form of o-NPOE, and meso-tetra methyl tetrakis-[methyl-2-(4-acetlphenoxy)] calix[4]pyrrole (KP) used as a carrier, were prepared and tested for the effective purification of aqueous solutions of methylene blue dye. The scanning electron microscope (SEM), thermogravimetric analysis (TGA), and attenuated total reflection Fourier transform infrared (ATR-FTIR) were used to define the microstructure and surface of PIMs. Experimental results showed that with the increased concentration of methylene blue in an aqueous solution, the removal percentage also increased. Further observation also showed that the flux increased with the rise of the source phase pH values from 3 to 10. The carrier and plasticizer content in the membrane significantly influenced the membrane’s transport properties. The optimal composition of the membrane in per cent by weight was for KP: 74% plasticizer; 18% support; 8% carrier. It was shown that the membrane with optimal composition showed good reusability and enabled the easy and spontaneous separation of methylene blue from aqueous solutions.

IgE-mediated wheat allergy is a gluten-related disorder. Wheat is one of the five most common food allergens in children. However, the natural history of IgE-mediated wheat allergy has seldom been described in the research literature. This study presents the current state of knowledge about the IgE-mediated wheat allergy in children.

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

In this paper, we proposed the fusion of two projection based face recognition algorithms: local binary Patterns in DCT domain and singular value decomposition (SVD) characterized by its simplicity and efficiently. Standard databases ORL are used to test the experimental results which prove that proposed system achieves more accurate face recognition as compared to individual method.

With the ongoing amendment of the EU legislation on the treatment of urban wastewater, stricter requirements for the removal of pollutants are expected, which calls for the need for innovative wastewater treatment technologies. Biological systems are still the first choice. The survey of typical bioreactors applied in wastewater treatment is presented. Wastewater treatment objective, bio-chemical environment and microbial growth are selected as a main criterion for classification of these bioreactors. Hydraulic and kinetic aspects are considered, advantages and drawbacks of these bioreactors regarding the selection of appropriate type of the reactor as well as regarding operation of reactors are mentioned. The aim of this paper is to provide operators and designers with a brief overview of selected traditional and advanced processes, reactors, and technologies for nutrient removal from municipal wastewater. Another goal is to discuss the possibilities and limitations to comply with more strict effluent standards. From the evaluation of the published papers, it follows that the currently applied traditional methods of nutrients removal have the potential to convey also with the expected stricter limits.

Despite the recognized influence of maximum or acceleration strength on combat techniques and countermovement jump (CMJ) performance, the relationship between body segment weights and combat techniques remains unexplored. This study aimed to examine the impact of body segment weights, including striking arm weight (SAW), kicking leg weight (KLW), and trunk weight (TW), on the dynamics of direct punches (DP), palm strikes (PS), elbow strikes (ES), front kicks (FK), and CMJ performance. Sixteen male military cadets (22.3±1.8 years, 181.4±7.0 cm, 83.0±8.1 kg) performed combat techniques, with performance measured by using a force plate and body segment weights assessed by Dual-energy X-ray absorptiometry. Spearman's correlation analysis was applied. Results indicated a strong correlation between KLW and FK impulse (r = 0.64, p ≤ 0.01) and CMJ impact force (r = 0.80, p ≤ 0.01). SAW showed moderate correlations with DP impulse (r = 0.53, p ≤ 0.05) and ES impulse (r = 0.54, p ≤ 0.05). Additionally, FK peak and impact forces were strongly correlated with CMJ jump height (r = 0.74, p ≤ 0.01; r = 0.77, p ≤ 0.01), and FK peak force moderately correlated with CMJ peak velocity (r = 0.63, p ≤ 0.05). These findings suggest targeted arm strength training could enhance striking abilities, while improvements in leg acceleration strength may directly boost kicking performance and vertical jump capabilities, which are crucial in combat scenarios.

Although a growing number of evidence emphasizes superior of VATS over conventional thoracotomy, still is little known about early postoperative diaphragm muscle function after lobectomy via these two approahces. To fill the gap in existing literature, we conducted comparative study between VATS and conventional thoracotomy in terms of postoperative diaphragm muscle function, assessing its contractility, strength, magnitude of effort and potential risk of dysfunction such as: atrophy and paralysis. A total of 59 patients (30 after VATS), who underwent anatomical pulmonary resection at our institution, were enrolled into this study. The control group was consisted of 28 health subjects without medical condition could contribute to diaphragm dysfunction. Diaphragm muscle was assessed before and after surgery using ultrasonography. We found that both surgical approaches were associated with postoperative impairment of diaphragm muscle function - compared to baseline data. Postoperative reduction of diaphragm contraction was demonstrated in all of 59 patients. In case of control group, the differences between measurements were no observed. We noted that lobectomy via thoracotomy was linked with greater percentage of patients with diaphragm paralysis or/and atrophy that VATS. Similar findings were observed in refer to diaphragm magnitude effort, as well as, diaphragm contraction strength, where minimal invasive surgery was associated with better diaphragm function parameters - in comparison to thoracotomy. Disturbance of diaphragm work was reported both at operated and non-operated side. Upper right and left lobectomy was connected with greater diaphragm function impairment than other segments. In conclusion, VATS technique seems to be less invasive than conventional thoracotomy providing a better postoperative function of a main respiratory muscle.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

In the modern power grid, characterized by the increased penetration of power electronics and extensive utilization of renewable energy, inverters-based power plants play a pivotal role as the principal interface of renewable energy sources (RESs) and the grid. Considering the stability characteristics of grid-following (GFL) inverters when the grid is relatively weak, the application of grid-forming (GFM) controls becomes imperative to enhance the stability of the entire power plant. Thus, there is an urgent need for suitable and effective models to study the interaction and stability of the paralleled inverters employing GFL and GFM controls. Thus, the small-signal modeling with full-order state space model and eigenvalues analysis is presented in this paper. First, the small-signal state-space model of the individual GFL and GFM inverters is obtained considering the control loop, interaction, reference frame, transmissions, and time delays. Then, the models of the individual inverter are extended to the hybrid inverters to study the effects of the GFM inverters on the small- signal stability of the entire system. And, the impacts of the inertia and damping are analyzed by the eigenvalues of the state-transition matrix. Case comprising three parallel GFL inverters and two GFL inverters with one GFM inverter, respectively, are studied to examine the effectiveness and accuracy of the model. Finally, the stability margin obtained from the eigenvalue analysis of the entire system is verified by time-domain simulations.

Pulmonary hypertension (PH) is a progressive and potentially fatal complication of sickle cell disease (SCD) affecting 6-10% of adult SCD patients. Various mechanisms and theories have been evaluated to explain the pathophysiology of the disease. However, questions remain, particularly regarding the clinical heterogeneity of the disease in terms of symptoms, complications, and survival. Beyond the classical mechanisms that have been thoroughly investigated and include hemolysis, nitric oxide availability, endothelial disorders, thrombosis, and left heart failure, attention is focused nowadays on the potential role of the genes involved in such processes. Potential candidate genes are investigated through next-generation sequencing, with the TGF-β pathway being the initial target. This field of research may also provide novel targets for pharmacologic agents in the future as is already the case with idiopathic PH. The collection and processing of data and samples from multiple centers can yield safe results that will allow a better understanding of SCD-related PH as a part of the disease’s clinical spectrum. The following review attempts to capture the most recent findings of studies on gene polymorphisms that have been associated with PH in SCD patients.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

In Germany, the phloem sucking planthopper Pentastiridius leporinus (Hemiptera: Cixiidae) currently represents the epidemiological driver for the spread of the syndrome “Basses Richesses” in sugar beet, which results in a reduced sugar content and an economic loss for the farmers. This disease is associated with the γ-proteobacterium ‘Candidatus Arsenophonus phytopathogenicus’ and the Stolbur phytoplasma ‘Candidatus Phytoplasma solani’. Recently, P. leporinus was found in potato fields in Germany associated with Stolbur-like symptoms in this crop. In this study, we confirmed that the vector completes its lifecycle on sugar beet as well as on potato when reared under controlled conditions. Transmission experiments with adults of this vector combined with molecular analyses showed for the first time that both pathogens are transmitted by this vector to potato. For an accurate assessment of the Ca. P. solani and Ca. A. phytopathogenicus titers in the vector and host plants, gBlocks derived from the hsp20- and 16S rRNA gene were employed, respectively. For Ca. P. solani the limit of detection was determined in potato and sugar beet material. The results of this study will further research on the epidemiology of the syndrome “Basses Richesses” and “Stolbur” diseases and the response of host plants and vector insects to both pathogens.

Fingerprints are essential for human identification and are valuable tools in criminal investigations. The pursuit of new materials for digital printing is expanding, with increasing interest in natural compounds such as bixin, sourced from annatto seeds. Despite its traditional use as a natural dye with medicinal properties, the potential of bixin in papilloscopy remains largely untapped. In this study, we meticulously extracted bixin from annatto seeds and meticulously developed composites incorporating zinc carbonate (bixin/ZnCO3) and kaolinite (bixin/kaolinite). UV-visible spectroscopy was used for characterization, and the extracted bixin showed absorption peaks at 429, 453, and 481 nm, which were very similar to standard peaks at 429, 457, and 487 nm. The two samples also had the same retention times (7.07 min) according to further liquid chromatography analysis. Sweat pores were easier to detect thanks to the effectiveness of the bixin/ZnCO3 and bixin/kaolinite composites in creating high contrast sebaceous and natural latent fingerprints. These results highlight the composites’ potential as novel and fascinating instruments for papilloscopy applications, which might also improve forensic investigations.

Latin America and the Caribbean offer the most favorable natural and social conditions for the emergence of cattle ranching that regenerate and maintains the ecosystem services on which life on Earth depends, that is energy efficient and that contributes to meeting fundamental human food needs. Unlike other major global producers, cattle farming in Latin America and the Caribbean is fundamentally based on pasture. Therein lies both its strength (due to the regenerative potential of well-managed pastures) and its vulnerability (due to the pervasive link between deforestation and pasture formation, especially in the Amazon, where 40% of the Brazilian herd is concentrated). The diversification of pastures (today marked by impressive monotony, with brachiaria accounting for 85% of the species in Brazil), the introduction of legumes and tree plantations within them, and the proper management of herds, open the way to the possibility of drastically reducing the area currently occupied by the activity (especially in the Amazon) while maintaining the supply of its products. Agricultural research has disseminated forms of moderate intensification of cattle ranching, which represent a low opportunity cost of animal feed and, at the same time, regeneration of ecosystem services that have so far been destroyed by the prevailing methods of farming.

The effects of CO₂-water-rock interactions on the mechanical properties of shale are essential for estimating the possibility of sequestrating CO₂ in shale reservoirs. In this study, uniaxial compressive strength (UCS) tests together with an acoustic emission (AE) system and SEM & EDS analysis were performed to investigate the mechanical properties and microstructural changes of black shales with different saturation times (10 days, 20 days and 30 days) in water dissoluted with sub-/super-critical CO₂. According to the experimental results, the values of UCS, Young’s modulus and brittleness index decrease gradually with increasing saturation time in water with sub-/super-critical CO₂. Compared to intact samples, 30-days’ saturation causes reductions of 56.43% in UCS and 54.21% in Young’s modulus for sub-critical saturated samples, and 66.05% in UCS and 56.32% in Young’s modulus for super-critical saturated samples, respectively. The brittleness index also decreases drastically from 84.3% for intact samples to 50.9% for samples saturated in water with sub-critical CO₂, to 47.9% for samples saturated in water with super-critical carbon dioxide (SC-CO₂). SC-CO₂ causes a greater reduction of shale’s mechanical properties. The crack propagation results obtained from the AE system show that longer saturation time produces higher peak cumulative AE energy. SEM images show that many pores occur when shale samples are saturated in water with sub-/super-critical CO₂. The EDS results show that CO₂-water-rock interactions increase the percentages of C and Fe and decrease the percentages of Al and K on the surface of saturated samples when compared to intact samples.

Merkel cell carcinoma (MCC) is a rare, highly aggressive skin cancer characterized by two etiologies: the first one, observed in most cases, is attributed to Merkel cell polyomavirus (MCPyV), a DNA tumor virus, while the second one is due to ultraviolet (UV) radiation exposure. Currently, there are limited diagnostic, prognostic, and therapeutic biomarkers available for MCC. MicroRNAs (miRNAs) are small RNA molecules that do not code for proteins but regulate various cellular processes, including cell cycle progression, proliferation, differentiation, and apoptosis. The dysregulation of miRNAs has been associated with a wide range of cancers since they can act as either tumor suppressors or oncogenes. This paper aims to collect, summarize and re-organize the recent discoveries concerning miRNAs, whose dysregulation in the pathogenesis and progression of MCC is slowly emerging. Furthermore, the potential clinical applications of miRNAs as diagnostic biomarkers, possible differentiation between MCPyV-related and unrelated MCC, predictors of response to therapy and prognostics are also discussed. From this review, it emerges that miRNAs may have, in the near future, the potential to become clinically significant in improving the diagnostic accuracy, prognostic evaluation, and therapeutic options of MCCs. Finally, the new perspectives on the poorly explored field of artificial intelligence in MCC are provided.

This paper investigates pseudo-polymorphism in 2-pyridylmethoxy derivatives of p-tert-butylcalix[4]arene (PyC4), p-tert-butyldihomooxa-calix[4]arenes (PyHOC4), and p-tert-butylhexahomotrioxacalix[3]arenes (PyHO3C3), presenting 11 crystal structures with 15 crystallographically independent molecules. The macrocycle of PyC4 is smaller and less flexible with respect to those of PyHOC4 and PyHO3C3 and in solution, the cone conformation of these three molecules exhibit different point symmetries: C4, Cs and C3, respectively. A correlation is observed between the macrocycle's structural rigidity and the number of pseudo-polymorphs formed. The more rigid PyC4 displays a higher number (6) of pseudo-polymorphs compared to PyHOC4 and PyHO3C3, which exhibit a smaller number of crystalline forms (3 and 2, respectively). The X-ray structures obtained show that the conformation of the macrorings is primarily influenced by the presence of an acetonitrile guest molecule within the cavity, with limited impact from crystal packing and intermolecular cocrystallized solvent molecules. Notably, both calix[4]arene derivatives produce host-guest complex with acetonitrile, while the most flexible and less aromatic PyHO3C3 do not give crystals with acetonitrile as guest. Intertwined 1D and 2D solvent channel networks were observed in the PyHOC4-hexane and in the PyHO3C3-H2O-MeOH crystal structures, respectively, while the other pseudopolymorphs of PyHOC4 and PyHO3C3 and all PyC4 crystal forms exhibit a closely packed crystal structures without open channels.

Nowadays, network simulators are very useful to model a communications system. In this technical note we will focus in the creation of a new error model in NS-3 network simulator. This note describes the main steps to create or modify an Wi-Fi error model in this network simulator. In our case, we have created a new error model to included the approach of [1] to compute PER (Packet Error Rate) for vehicular environments.

Mass customization, small batch sizes, high variability of product types and a changing product portfolio during the life cycle of an industrial plant are current trends in the industry. Due to an increasing decoupling of the development of software and hardware components in an industrial context, compatibility problems within industrial control systems arise more and more frequently. In this publication, a strategy concept for compatibility testing is derived and discussed by means of literature review and applied research. This 4-phased strategy concept identifies incompatibilities between software and hardware components in the industrial control environment and enables test engineers to detect problems at an early stage. By automating the compatibility test on an external I-PC, the test can be run both when new software is installed on the industrial controller and when the controller is restarted. Thus, changes to the components are constantly detected and incompatibilities are avoided. Furthermore, early incompatibility detection can ensure that a system remains permanently operational. Based on a discussion, additionally strategies are identified to consolidate the robustness and applicability of the presented concept.

In this paper, a new approach to retrieve semantic images based on shape and geometric features of image in conjunction with multi-class support vector machine is proposed. Zernike moment as shape feature is to verify the invariance of objects for silhouette image. In addition, a set of geometrical features is to explore the objects shape using two features of rectangularity and circularity. Then the extracted features are normalized and employed for multi-class support vector machine either for learning or retrieving processes. The retrieving process relies on three main tasks which namely Query Engine, Matching Module and Ontology Manger, respectively. Query Engine is to build the input text or image query using SPARQL language. The matching module extracts the shape and geometric features of image’s objects and employ them to Ontology Manger which in turn inserts them in ontology knowledge base. Benchmark mammals have been conducted to empirically conclude the outcome of proposed approach. Our experiment on text and image retrieval yields efficient results to problematic phenomena than previously reported.

In the early decades of the 19th century, the deaf population in the eastern US and Canada was distributed across a vast area. After the 1817 founding of the American School for the Deaf (ASD) in Hartford, CT and the subsequent establishment of schools for the deaf in New York City (NYSD), Philadelphia, and many other US states, hundreds of deaf students called these schools home for several years. After leaving school, the early American Deaf community faced a challenge: How would the community maintain its social and linguistic ties across a vast geographical area once community members had dispersed to their hometowns? In this paper we analyze the attendance registries of two large gatherings of deaf individuals in Hartford in the years 1850 and 1854. These were among the largest and earliest known gatherings of deaf adults. The demographic data included in these registries open a window onto the evolving American Deaf community of the mid-19th century. Our analyses of the attendees’ school affiliations, ages, and marital status show that the signing community that had taken root among students at schools in Hartford and New York persisted among the adult graduates of those schools in towns across the northeastern US. We compare the places of residence of ASD and NYSD alumni in 1850 and 1854 to their hometowns when they first enrolled at school. Our comparisons suggest the mid-19th-century signing community had become more urban; it was centered to a greater extent in populous cities such as New York, Boston, and Hartford than had been true when the attendees had enrolled in school. We consider how the geography of deafness in the 19th century might inform our understanding of the sources of regional variation in ASL. We also consider how early cross-regional interactions may have inhibited such regional variation.

Free and open source hardware (FOSH) development has been shown to increase innovation and reduce economic costs. This article reviews the opportunity to use FOSH like a sanction to undercut imports and exports from a target criminal country. A formal methodology is presented for selecting strategic national investments in FOSH development to improve both national security and global safety. In this methodology, first the target country that is threatening national security or safety is identified. Next, the top imports from the target country as well as potentially other importing countries (allies) are quantified. Hardware is identified that could undercut imports/exports from the target country. Finally, methods to support the FOSH development are enumerated to support production in a commons-based peer production strategy. To demonstrate how this theoretical method works in practice it is applied as a case study to the current criminal military aggressor nation, who is also a fossil fuel exporter. The results show there are numerous existing FOSH and opportunities to develop new FOSH for energy conservation and renewable energy to reduce fossil fuel energy demand. Widespread deployment would reduce the concomitant pollution, human health impacts, and environmental desecration as well as cut financing of military operations.

Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

Software analysis, debugging, and reverse engineering have a crucial impact in today’s software industry. Efficient and stealthy debuggers are especially relevant for malware analysis. However, existing debugging platforms fail to address a transparent, effective, and high-performance low-level debugger due to their detectable fingerprints, complexity, and implementation restrictions. In this paper, we present HyperDbg, a new hypervisor-assisted debugger for high-performance and stealthy debugging of user and kernel applications. To accomplish this, HyperDbg relies on state-of-the-art hardware features available in today’s CPUs, such as VT-x and extended page tables. In contrast to other widely used existing debuggers, we design HyperDbg using a custom hypervisor, making it independent of OS functionality or API. We propose hardware-based instruction-level emulation and OS-level API hooking via extended page tables to increase the stealthiness. Our results of the dynamic analysis of 10,853 malware samples show that HyperDbg’s stealthiness allows debugging on average 22% and 26% more samples than WinDbg and x64dbg, respectively. Moreover, in contrast to existing debuggers, HyperDbg is not detected by any of the 13 tested packers and protectors. We improve the performance over other debuggers by deploying a VMX-compatible script engine, eliminating unnecessary context switches. Our experiment on three concrete debugging scenarios shows that compared to WinDbg as the only kernel debugger, HyperDbg performs step-in, conditional breaks, and syscall recording, 2.98x, 1319x, and 2018x faster, respectively. We finally show real-world applications, such as a 0-day analysis, structure reconstruction for reverse engineering, software performance analysis, and code-coverage analysis.

The Internet of Things (IoT) is a concept based on the integration of various devices and methods of communication to exchange information in order to contribute to the improvement of everyday life, business and environment. This paper focuses on the establishment of a modern Internet of Things platform to ensure secure collection, processing and storage of data, under unexpected events. This platform establishes reliable connectivity which enhance system uptime; the key to success when implementing an IoT strategy. For this purpose, we proposed a hybrid approach combining different connectivity technologies to ensure the availability and smooth operation of the system and the prevention of data loss in unforeseen cases.

Background and Objectives: ARNE score was developed for the prediction of difficult airway for both general and ENT surgery with a universal cut-off value. We tested the accuracy of this score in the case of laryngeal surgery and provided an insight of its combination with flexible laryngoscopy. Materials and Methods: This prospective pilot clinical study included 100 patients who were being scheduled for microscopic laryngeal surgery. We have calculated ARNE score for every patient and flexible laryngoscopy was provided preoperative. Difficult intubation was assessed according to intubation difficulty score (IDS). Results: A total of 33% patients had difficult intubation according to IDS. ARNE score showed to be accurate for prediction of difficult intubation in laryngology with P<0.0001 and AUC 0.784. Flexible laryngoscopy showed to be an independent parameter with P<0.0001 and AUC 0.766. We have defined a new cut-off value of 15.50 for laryngology, according to AUC curve. After the patients were divided in two groups, according to the new cut-off value and provided cut-off value, AUC improved to 0.707 from 0.619 respectively. Flexible laryngoscopy improved the prediction model of ARNE score to AUC 0.882 and of new cut-off value to AUC 0.833. Conclusions: It is recommended to use flexible laryngoscopy together with ARNE score in difficult airway prediction in patients with laryngeal pathology. Also, universally recommended cut-off value of 11 can not be effectively used in laryngology and a new cut-off value of 15.50 is recommended.

Despite the successful introduction of oral cholera vaccines, Zambia continues to experience multiple, sporadic, and protracted cholera outbreaks in various parts of the country. While vaccines have been useful in staying the cholera outbreaks, the ideal window for re-vaccinating individual’s resident in cholera hotspot areas remains unclear. Using a prospective cohort study design, 225 individuals were enrolled, re-vaccinated with two doses of Shanchol™ regardless of previous vaccination and followed-up for 90 days. Bloods collected at baseline before re-vaccination, at day 14 prior to second dosing and subsequently on days 28, 60, and 90. Vibriocidal assay was performed on samples collected at all five time points. Our results showed that anti-LPS and vibriocidal antibody titers increased at day 14 after re-vaccination and decreased gradually at 28, 60 and 90 across all the groups. Seroconversion rates were generally comparable in all treatment arms. We therefore conclude that vibriocidal antibody titers generated in response to re-vaccination still wane quickly irrespective of previous vaccination status. However, despite the observed decline, the levels of vibriocidal antibodies remained elevated over baseline values across all groups, an important aspect for Zambia where there is no empirical evidence as to the ideal time for re-vaccination.

Currently, the textile industry is a poorly automated sector, due in part to problems in the handling of deformable leather and textile parts during production operations. In this work, several problems in the handling process of leather and textile parts are addressed, introducing methods to increase the automation of the process. A pneumatic actuator designed to pick up textile or leather parts avoiding their deformation during transport has been developed. This actuator maximizes the number of gripping points to improve handling, making it more stable and efficient. Additionally, a vision system has been implemented in the part picking task which, in conjunction with the CAD information of the part, sends the modified gripping position of the part to the robot. This allows customized handling of each textile or leather part. Finally, validation tests have been carried out on this development, both in simulations and in laboratory conditions, demonstrating its viability and direct applicability in the production line.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

The abundant mechanical vibration energy in bridge road environment can be converted into electric energy by using the piezoelectric energy harvest technology, which could be an efficient way to provide energy required by the wireless sensor network in the bridge condition monitoring system. An autonomous energy harvesting system has been designed based on cantilever beams for sensing and acquiring the bridge vibration energy. After the analysis of the dynamic properties of the piezoelectric cantilever beam in the energy conversion, three kinds of interface circuits were compared through simulation and experimental results. It was shown that the VD interface circuit has less power loss. Furthermore, the proposed closed loop control method based on the VD circuit was simple, adaptive, and self-powered, which is suitable for the road energy harvesting application. Finally, the energy harvesting system based on VD circuit was realized with harvested power of around 0.8mW.

As the automotive industry undergoes a transformative phase driven by technological advancements, the integration of driving simulators stands out as an important tool for research and development. These simulators offer a controlled environment for studying driver behavior; however, the alignment of data remains a complex aspect that warrants thorough investigation. This research investigates driver state classification using a dataset obtained from real-road and simulated conditions, recorded through JINS MEME ES_R smart glasses. The data set encompasses electrooculography signals, with a focus on standardizing and processing the data for subsequent analysis. For this purpose, we used a recurrent neural network model, which yielded 95.21% accuracy on testing dataset. The findings of this study indicate the plausible use of proposed methodology in practical scenarios, providing possibility for developments in intelligent transportation systems and driver monitoring technology.

Hip joint surgeries, including total hip replacement or resurfacing, have increased tremendously in the last decades. Number of patients of all ages, replace their hip, due to severe injuries or trauma problems, so as to have a better life. According to these factors, new material and processes in implants manufacturing are imported to medicine, through research programs, every year. In the scope of one of these programs, that has to do with ceramic coatings on metallic resurfacing implants, a new 3axis Hip simulator was designed and manufactured in the Laboratory of Manufacturing Technology of the National Technical University of Athens. The scope of this paper is to present the main parts, materials and process used to manufacture the simulator as well as the way the simulator is working and how its movement in 3axis is accomplished. Furthermore, the evaluation of the machine and its use to examine resurfacing implants is presented.

TomoSim comes as part of project ATMOS, a miniaturised DOAS tomographic atmospheric evaluation device, designed to fit a small drone. During the development of the project, it became necessary to write a simulation tool for system validation. TomoSim is the answer to this problem. The software has two main goals: to mathematically validate the tomographic acquisition method; and to allow some adjustments to the system before reaching final product stages. This measurement strategy was based on a drone performing a sequential trajectory and gathering projections arranged in fan beams, before using some classical tomographic methods to reconstruct a spectral image. The team tested three different reconstruction algorithms, all of which were able to produce an image, validating the team’s initial assumptions regarding the trajectory and acquisition strategy. All algorithms were assessed on their computational performance and their ability for reconstructing spectral "images", using two phantoms, one of which custom made for this purpose. In the end, the team was also able to uncover certain limitations of the TomoSim approach that should be addressed before the final stages of the system.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

Depressions containing partially molten rocks were investigated in Quaternary pebbly sedi-ments in Alpine foreland in Bavaria, Germany. Ruins of limekilns from 18-19th centuries are abundant around Seeshaupt. They are usually associated with earthworks for fuel feeding and protection from wind. Depressions contain partially molten stones from furnace walls, with lime and burnt loam remnants. On the surface of pebbles (typically gneisses), green glass formed with chemical composition possibly affected by moderately volatile components of wood biomass, mainly K and Cu. Thermoplastic deformation of pebbles is limited and the sur-face melt deformation points to slow flow. At Emmerting, on the other hand, two walled circu-lar depressions which lack additional earthworks have been identified as possible impact cra-ters. Thermally affected pebbles show much more intense deformation. Colorless to greenish glass, also K and Cu enriched, usually forms only thin surface coatings, in places covered by younger melt extruded from pebble interior. Burnt loam is missing. At Grabenstätt-Kaltenbach, a depression of unclear origin was investigated. Morphologically, it matches craters rather than limekilns, but anthropogenic contamination (brick-like material) is probable. The rare molten samples do not display extreme deformation features. The thermally affected stones, mainly those from Emmerting, have elevated magnetic susceptibility.

The suspended test masses of gravitational-wave (GW) detectors require precise alignment to be able to operate the detector stably and with high sensitivity. This includes the continuous counter-acting of seismic disturbances, which, below a few Hertz, are not sufficiently reduced by the seismic isolation system. The residual angular motion of suspended test masses is further suppressed by the Angular Sensing and Control (ASC) system. However, in doing so, the angular motion can be enhanced by the ASC at higher frequencies where the seismic isolation system is very effective. This has led to sensitivity limitations between about 10 Hz and 25 Hz of the LIGO detectors in past observation runs. The observed ASC noise was larger than simple models predict, which means that more accurate detector models and new simulation tools are required. We present Lightsaber, a new time-domain simulator of the ASC in LIGO. The simulation is a nonlinear simulation of the optomechanical system consisting of the high-power cavity laser beam and the last two stages of suspension in LIGO including the ASC. The main noise inputs are power fluctuations of the laser beam at the input of the arm cavities, read-out noise of sensors used for the ASC, displacement noise from the suspension platforms, and noise introduced by the suspension damping loops. While the plant simulation uses local degrees of freedom of individual suspension systems, the control is applied on a global angular basis, which requires a conversion between the local and global bases for sensing and actuation. Some of the studies that can be done with this simulation concern mis-centering of the beam-spot (BS) position on the test masses, the role of laser power fluctuations for angular dynamics, and the role of the various nonlinear dynamics.

Interstitial lung disease (ILD) is one of the most serious extra-articular complications of rheu-matoid arthritis (RA), which increases the mortality of RA. Because the pathogenesis of RA-ILD remains poorly understood, appropriate therapeutic strategies and biomarkers have not yet been identified. Thus, the goal of this review was to summarize and analyze the reported data on the etiology and pathogenesis of RA-ILD. The incidence of RA-ILD increases with age, and is also generally higher in men than in women and in patients with specific genetic variations and eth-nicity. Lifestyle factors associated with an increased risk of RA-ILD include smoking and exposure to pollutants. The presence of an anti-cyclic citrullinated peptide antibody, high RA disease activity, and rheumatoid factor positivity also increase the risk of RA-ILD. We also explored the roles of biological processes (e.g., fibroblast–myofibroblast transition, epithelial–mesenchymal transition, and immunological processes), signaling pathways (e.g., JAK/STAT and PI3K/Akt), and the his-topathology of RA involved in RA-ILD pathogenesis based on published preclinical and clinical models of RA-ILD in animal and human studies.

The concept of a Social License to Operate (SLO) has become increasingly important in the sustainability literature in recent years. Having its origins in the business discourse of the mining industry with respect to limiting opposition to mining projects, the notion of a social contract above and beyond legal requirements has since become applied across a number of different industries. Despite the concepts adoption confusion exists over the practices and outcomes of SLO, and particularly the nature of engagement. Given this situation it is surprising that not more attention to the role of marketing, and social marketing in particular, in operationalizing the concept. The paper discusses the potential of social marketing to contribute to SLO. Economic, political and social relations are complex in SLO and exchange is intricate in such relational environments. A community-based social marketing orientation is proposed as a means to improve exchange relations and enhance engagement. Seven models of SLO related social marketing models are discussed with community-based social marketing and adaptive co-marketing models being regarded as the most positive for the achievement of an SLO. Potential barriers to adoption of these approaches are noted.

Chronic kidney disease patients treated by hemodialysis present a high cardio-vascular morbidity and mortality. There is an imperative need for novel biomarkers in identifying and to offer possible therapeutically intervention in these patients. We performed a prospective observational cohort study on 77 patients in the period October 2021 – October 2023. We measured serum plasma levels of Interleukin 1-Beta, Galectin 3, human suppression of tumorigenicity factor 2, bone morphogenetic protein 2 and fibroblastic growth factor 23 at the inclusion. We evaluated the correlations of these biomarkers with cardiac function and structure evaluated by echocardiography. Mean age was 61.02 (±11.81) years, 45 (56.2%) males and with a dialysis vintage of 4.95 (2.4-7.8) years. Median ejection fraction was 51 (43-54 %) and more than two thirds of the patients presented valvular calcifications. Overall mortality was 22%. Interleukin 1-Beta correlated positively with ejection fraction and global longitudinal strain and negatively with left atrium diameter and left ventricle tele systolic diameter. Galectin 3 values negatively correlated with aortic valve fibrosis and mitral valve calcifications and human suppression tumorigenity factor 2 negatively correlated with mitral valve calcifications. Some of these novel biomarkers could be used to better asses the cardio-vascular disease in patients on maintenance hemodialysis.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

This study considers an application of the first-order Grey Markov Model to foresee the values of Italian power generation in relation to the available energy sources. The model is used to fit data from the Italian energy system from 2000 to 2022. The integration of Markovian error introduces a random element to the model, which is able now to capture inherent uncertainties and misalignments between the Grey model predictions and the real data. This application provides valuable insights for strategic planning in the energy sector and future developments. The results show good accuracy of the predictions, which provides powerful information for the effective implementation of energy policies concerning the evolution of energy demand in the country. Despite advancements, Italy’s 2032 energy mix will still significantly rely on fossil fuels, emphasizing the need for sustained efforts beyond 2032 to enhance sustainability.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

Multiferroics, showing both ferroelectric and magnetic order, are promising candidates for future electronic devices. Especially, the fundamental understanding of ferroelectric switching is of key relevance for further improvements, which however is rarely reported in literature. On a prime example for a spin-driven multiferroic, LiCuVO₄, we present an extensive study of the ferroelectric order and the switching behavior as function of external electric and magnetic fields. From frequency-dependent polarization switching and using the Ishibashi-Orihara theory, we deduce the existence of ferroelectric domains and domain-walls. These have to be related to counterclockwise and clockwise spin-spirals leading to the formation of multiferroic domains. A novel measurement – multiferroic hysteresis loop – is established to analyze the electrical polarization simultaneously as a function of electrical and magnetic fields. This technique allows characterizing the complex coupling between ferroelectric and magnetic order in multiferroic LiCuVO₄.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

The classification of Trojans in modern analog microcircuits is considered. Using high-speed operational amplifiers (Op-Amps) as an example, the relationship between Op-Amp circuit design and the formation of undesirable states in typical switching circuits is shown. Circuit solutions are proposed to minimize the Trojan states of high-speed Op-Amps. These include limiting the maximum output currents of the input stages of the Op-Amp during the transient process and the use of differentiating transient correction circuits in the Op-Amp.

Artificial intelligence (AI) has emerged as a powerful tool for addressing the challenges posed by climate change and their impact on public health. By leveraging its capacity to analyze and predict climatic patterns, AI offers opportunities to enhance resource management and develop effective strategies for climate change mitigation. Moreover, AI can contribute to generating sustainable solutions that address the complex and interconnected nature of climate change. For example, AI can enable the optimization of energy consumption and facilitate the integration of renewable energy sources into existing systems. It can also support the development of climate models that provide timely and accurate predictions, enabling policymakers to implement proactive measures for disaster preparedness and response. Furthermore, AI-powered disease surveillance and mitigation techniques can improve public health outcomes by identifying patterns and trends in the spread of diseases in relation to climatic factors.However, the widespread adoption of AI-based solutions is not without challenges. Ethical concerns surrounding privacy and data ownership must be addressed, as the use of AI requires access to large datasets, raising potential privacy risks. Technical constraints, such as limited computational power and the need for sophisticated algorithms, also pose obstacles to the implementation of AI in climate change mitigation strategies. Furthermore, issues related to the accessibility and affordability of AI technologies must be resolved to ensure equitable distribution and maximize its potential impact on public health.To fully harness the power of AI in addressing climate change and improving public health outcomes, it is crucial to promote innovation, multidisciplinary collaboration, and open data science. Innovation can drive the development of new AI algorithms and technologies specifically tailored to address climate change challenges. Multidisciplinary approaches that bring together experts from diverse fields, including climate science, public health, and computer science, can foster a holistic understanding of complex systems and enable the design of comprehensive solutions. Finally, open data science practices, such as sharing data and algorithms, can facilitate collaboration and accelerate progress in mitigating climate change and its public health impacts.In conclusion, AI offers promising opportunities for effectively addressing climate change and its impact on public health. However, to fully realize its potential, it is essential to tackle ethical and privacy concerns, overcome technical constraints, and ensure accessibility and affordability. By promoting innovation, multidisciplinary collaboration, and open data science, we can unlock the transformative power of AI in mitigating climate change and improving public health outcomes.

Gas and power networks are tightly coupled and interact with each other due to physically interconnected facilities. In an integrated gas and power network, a contingency observed in one system may cause iterative cascading failures, resulting in network wide disruptions. Therefore, understanding the impacts of the interactions in both systems is crucial for governments, system operators, regulators and operational planners, particularly, to ensure security of supply for the overall energy system. Although simulation has been widely used in the assessment of gas systems as well as power systems, there is a significant gap in simulation models that are able to address the coupling of both systems. In this paper, a simulation framework that models and simulates the gas and power network in an integrated manner is proposed. The framework consist of a transient model for the gas system and a steady state model for the power system based on AC-Optimal Power Flow. The gas and power system model are coupled through an interface which uses the coupling equations to establish the data exchange and coordination between the individual models. The bidirectional interlink between both systems considered in this studies are the fuel gas offtake of gas fired power plants for power generation and the power supply to LNG terminals and electric drivers installed in gas compressor stations and underground gas storage facilities. The simulation framework is implemented into an innovative simulation tool named SAInt (Scenario Analysis Interface for Energy Systems) and the capabilities of the tool are demonstrated by performing a contingency analysis for a real world example. Results indicate how a disruption triggered in one system propagates to the other system and affects the operation of critical facilities. In addition, the studies show the importance of using transient gas models for security of supply studies instead of successions of steady state models, where the time evolution of the line pack is not captured correctly.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Metal nanoparticles are used to modify/enhance the properties of a polymer matrix for a broad range of applications in bio-nanotechnology. Here, we study the properties of polymer/gold nanoparticle (NP) nanocomposites through atomistic molecular dynamics, MD, simulations. We probe the structural, conformational and dynamical properties of polymer chains at the vicinity of a gold (Au) NP and a functionalized (core/shell) Au NP, and compare them against the behavior of bulk PE. The bare Au NPs were constructed via a systematic methodology starting from ab-initio calculations and an atomistic Wulff construction algorithm resulting in the crystal shape with the minimum surface energy. For the functionalized NPs the interactions between gold atoms and chemically adsorbed functional groups change their shape. As a model polymer matrix we consider polyethylene of different molecular lengths, from the oligomer to unentangled Rouse like systems. By computing the different properties the concept of the interface, and the interphase as well, in polymer nanocomposites with metal NPs are critically examined. Results concerning polymer density profiles, bond order parameter, segmental and terminal dynamics show clearly that the size of the interface / interphase, depends on the actual property under study. In addition, the anchored polymeric chains change the behavior/properties, and especially the chain density profile and the dynamics, of the polymer chain at the vicinity of the Au NP.