The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Abstract: Peptide pools composed of short amino acid sequences have proven to be versatile tools in various research areas and clinical applications. They are powerful tools for epitope mapping, immunotherapy, and vaccine development. Their importance lies in their ability to map complex protein structures, enabling a comprehensive understanding of immune responses and facilitating the identification of potential therapeutic agents. The application of peptide pools also extends to the field of personalized medicine, offering tailored solutions for diseases such as cancer and infectious diseases. Peptide pools are complex mixtures of immunostimulatory antigens primarily intended for T-cell stimulation. They are commercially available in many different compositions and variants. However, unlike other reagents that consist of only one or a few compounds, peptide pools are highly complex products with limited stability. This makes their quality control a major challenge. Quantitative peptide analysis usually requires sophisticated methods, in most cases isotope-labeled standards and reference materials. None of these are routinely available for these products. Synthesis and purification of all labeled peptides might be required. Usually, this approach would be prohibitively laborious and expensive. Therefore, an approach is needed to provide a practical and feasible method for quality control of peptide pools. With insufficient quality control, the use of such products could lead to incorrect experimental results, which would worsen the well-known reproducibility crisis in the biomedical sciences. Here we propose the use of ultra-high performance liquid chromatography (UHPLC) with two detectors, a standard UV detector (at 214 nm) for quantitative analysis and a high-resolution mass spectrometer (HRMS) for identity confirmation. To be cost-efficient and fast, quantification and identification are performed in one chromatographic run. An optimized protocol is shown, and different peak integration methods are compared and discussed. This work was performed using a peptide pool known as CEF, which consists of 32 peptides derived from cytomegalovirus (CMV), Epstein-Barr virus (EBV) and influenza virus, ranging from 8 to 12 amino acids in length.

Autism spectrum disorder (ASD) is a neurodevelopmental disorder characterized by impairments in social interaction and communication, anxiety, hyperactivity, and restricted interest for specific subjects. In addition to the genetic factors, multiple environmental factors have been related to the development of ASD. Animal models can serve as crucial tools for understanding the complexity of ASD and identifying potential therapeutic strategies. In this study, a chemical model of ASD has been developed in zebrafish by exposing embryos to valproic acid (VPA) from 4 to 48 hours post-fertilization. After the exposure, embryos were transferred to fish water and the effects on behavior and neurotransmitters profile were analyzed at both larval and adult stages. Larvae from VPA-treated embryos showed hyperactivity and decreased visual and vibrational escape responses, as well as an altered neurotransmitters profile, with increased glutamate and decreased acetylcholine and norepinephrine levels. Adults from VPA-treated embryos exhibited impaired social behavior characterized by larger shoal sizes and a decreased interest for their conspecifics. Neurotransmitter analysis revealed a significant decrease in dopamine and GABA levels in the brain. These results support the interest of this model in the study of ASD.

Dogs population increased exponentially in the past decade while the birth rate decreased gradually, especially in the developed countries. Due to dogs’ characteristics of loyalty and obedience, most pet owners treated their dogs as their family members or companions, therefore they are willing to select and purchase safe, high quality and nutrition dog food to their dogs. However, there is lack of regulation or standard to reinforce the production or distribution of dog food in Hong Kong. Consequently, this paper will first review the relationship between high dog population and declining birth rate, types of dog food and typical ingredients. Secondly, the potential health implications of various “toxic” food ingredients for dog, hazard analysis of dog food and its testing methods will be investigated. Lastly, this paper will summarize worldwide existing standards and regulations, quality and hygiene management system related to dog food safety to provide insights and suggestions to Hong Kong government about the importance and urgency of implementing regulations and policies to oversee the imported and local manufactured dog food.

The recent availability of commercial platforms for behavioral analysis in zebrafish larvae based on video-tracking technologies has exponentially increased the number of studies analyzing different behaviors in this model organism to assess neurotoxicity. Among the most commonly used assays in zebrafish larvae are basal locomotor activity (BLA) and visual motor response (VMR). However, the effect of different intrinsic and extrinsic factors that can significantly alter the outcome of these assays is still not well understood. In this work we have analyzed in 143 larvae the influence of age (5-8 days post-fertilization), time of day (8:00, 10:00, 12:00, 14:00; 16:00, 18:00, and 20:00 h), and experiment (three experiments performed at different days) on BLA and VMR results (4,004 analyses for each behavior). Results from both behaviors were adjusted to a Random-Effects linear regression model using generalized least squares (GLS), including in the model the effect of the three variables, the second-way interactions between them and the three-way interaction. The results presented in this manuscript show a specific effect of all three intrinsic factors and their interactions on both behaviors, supporting the view that the most stable time period for performing these behavioral assays is from 10:00 am to 04:00 pm, with some differences depending on age of the larva and the behavioral test.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Attention to the work-related musculoskeletal disorders (WMSDs) involve also statistical surveys showing an increasing trend in the incidence of WMSDs. Technological development retrieves new tools and methods for the assessment of physical load at work. In addition to the conventional questionnaires and scaling assessment systems, these methods are mostly based on the direct sensing of appropriate parameters, which allows more precise quantification. The aim of this paper is to compare the assessment of ergonomic risk through current legislative regulations. A Captiv wireless sensor system was used at a car headlight quality control assembly workplace for sensing, data acquisition and data processing. During the evaluation of the postures and movements at work, we discovered differences in the applicable standards: Decree 542/2007 Coll. (Slovak legislation), STN EN 1005-4+A1, French standards default in the Captiv system. Standards define the thresholds for hazardous postures with significant differences in several evaluated body segments, which also affects the final evaluation of the measurements. Based on the results of our research, we found that respondents were in an acceptable position for approximately 63% of the total duration of the work activity in terms of the Legislative method, 44% with Captiv and 27% with Standards method.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Soil naturally contains fluorine, but concerns arise when its levels or bioavailability are increased by human activities or specific compounds. South Korea faces challenges in regulating soil fluorine pollution despite implementing stricter total fluorine standards than many developed countries. Moreover, these regulations can be economically unfeasible because of the naturally high background levels of fluorine in the soil in Korea. This review explores the global landscape of soil fluorine management strategies and examines potential solutions that reconcile environmental protection with economic concerns. We recommend a shift towards regulating specific and hazardous fluorine compounds rather than total content, and prioritizing remediation efforts based on assessments of bioavailable fluorine. This approach may help Korea establish a more effective and sustainable strategy for managing soil fluorine pollution.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

The role of foods is shifting from focusing on the provision of energy and basic nutrients to also include bioactive compounds that prevent the development of chronic age-related diseases. Mi-croalgae offer a source of nutritional compounds with important health effects, and have the po-tential for production of health-promoting products, without increasing agricultural land use and negatively impacting the environment. Here we investigate the health effects of microalgal ex-tracts with high levels of the colourless carotenoid phytoene. Phytoene is widely available from dietary sources and can be detected across different tissues in the human body. However, it is usually regarded as a precursor for the synthesis of other carotenoids, rather than a bioactive molecule. We utilised the model organism C. elegans to show that phytoene-rich extracts from Chlorella sorokiniana and Dunaliella bardawil have anti-ageing properties. The extracts protect against oxidative damage and amyloid-β42 proteotoxicity (a major pathology of Alzheimer's disease), and extends lifespan. We show that pure phytoene also has these anti-ageing effects, suggesting that phytoene is a bioactive molecule with positive effects on ageing and longevity.

The circular economy is one of the main strategies for mitigating the environmental impacts of civil construction, due to the generation of construction and demolition waste (CDW). In this transition, evaluating alternatives for using buildings as material banks is a way to make the process of reusing construction components more efficient. Thus, the article aimed to evaluate the state of the art of publications on the relationship between the circular economy in civil construction and the conceptual model of buildings as material banks, to mitigate the environmental impacts of CDW. The authors chose the methodological design of Systematic Literature Review, using the Scopus and Web of Science databases for research, with the following search strings: ("construction" or "civil construction" or "built environment" or "construction industry" ) and ("circular economy" or "circular construction") and ("material banks" or "BAMB" or "buildings as material banks" or "building stocks" or "building materials") and ("construction waste" or "demolition waste" or "CDW" or "construction and demolition waste" or "environmental impacts"). After a screening in which only articles published in journals were selected, from 2013 to 2023, inclusion and exclusion criteria were applied, to evaluate only those that had a direct relationship with CDW management through circular economy strategies and buildings such as banks of material. As a result, 93 articles remained, which were analyzed using quantitative and qualitative approach. The quantitative results showed an increase in publications since 2020, which are concentrated in European countries and China. The predominance of applied studies was also noted, through case studies that evaluate the management of materials and waste in the urban environment. The qualitative analysis, carried out using a SWOT Matrix, highlighted the strengths of the buildings, such as material banks, the potential reduction of resource extraction and urban mining, promoting the circulation of construction products. However, the recycling of waste, such as aggregates, still stands out as the main end-of-life strategy adopted, even without occupying the top of the waste hierarchy.

Background/Objectives: PEMF therapy has gained significant attention due to its potential benefits in promoting tissue repair and improving overall well-being. Recent publications in the field of exercise physiology, showed that pulsed electromagnetic fields (PEMFs) enhanced the velocity and the quantity of muscle O2 available and the rate of muscle oxygen extraction and utilization, in semi-professional cyclists, during a heavy constant-load exercise. In this paper, we investigate the effect of stimulation on muscular activation, in sedentary young people, during a constant-load exercise, performed at moderate intensity. Methods: Nine male sedentary young people, partic-ipated in this study. The response of the muscle activity, was recorded by surface EMG and assessed measuring the root mean square (RMS) normalized to the peak of the maximum voluntary con-traction. Data were collected in the right vastus Medialis (RVM) and right Biceps Femoris (RBF) at the baseline (standstill sitting), on warm-up (unloaded cycling) and during 30 minutes of con-stant-load exercise, in two experimental conditions (PEMF ON vs PEMF OFF). Results: The mul-tivariate analysis of variance performed on RVM showed a significant effect of PEMF in both warmup and exercise, while on RBF showed a significant effect of PEMF and warmup. Conclusions: PEMF strongly enhanced the amplitude of muscle activity in young sedentary people. The increase in the amplitude of the muscular response may lead to a higher oxygen consumption and release.

In recent years there has been an increasing interest in developing novel materials based on natural biopolymers as a renewable alternative of petroleum-based plastics. The availability of proteins derived from agricultural by-products, along with their favourable properties, has fostered a renewed interest in protein-based materials, promoting research in innovative technologies. In this study we propose the use of rapeseed protein-rich meal as main ingredient for the preparation of novel sustainable materials combining excellent environmental properties such as biodegradability and renewable origin. Application as sustainable products in the present high-tech society needs modification of basic native properties of these natural compounds. The original route proposed in this paper consists in the preparation via compression moulding of flexible biomaterials stabilized by crosslinkers/chain extenders. Investigation of the effects of different denaturing and disulfide bond reducing agents, crosslinkers, and preparation conditions on the material mechanical behaviour demonstrated that the novel materials have appreciable strength and stiffness. The results show the potential of utilizing full meal from vegetable by-products to prepare protein-based materials with granted ecofriendly characteristics and mechanical properties adequate to specific structural applications.

Virus taxonomy uses a Linnaean-like subsumption hierarchy to classify viruses into taxonomic units at species and higher rank levels. Virus species are considered monophyletic groups of mobile genetic elements (MGEs) often delimited by phylogenetic analysis of aligned genomic or metagenomic sequences. Taxonomic units are assumed independent organizational, functional and evolutionary units that follow a ‘natural’ historical rationale. Here, I use phylogenomic and other arguments to show that viruses are not self-standing genetically-driven biological systems. Instead, they are crucial components of holobionts, units of biological organization that dynamically integrate the genetics, epigenetic, physiological and functional properties of their co-evolving members. Remarkably, phylogenomic analyses show viruses share protein domain and loop structures with cells throughout history via massive processes of reticulate evolution, helping spread evolutionary innovations across a wider taxonomic spectrum. Thus, viruses are not merely MGEs or microbes. Instead, their genomes and proteomes conduct cellularly integrated processes akin to those cataloged by the GO Consortium. This prompts the generation of compositional hierarchies that replace the ‘is-a-kind-of’ by a ‘is-a-part-of’ logic to better describe the mereology of integrated cellular and viral makeup. My analysis demands a new paradigm that integrates virus taxonomy into a modern evolutionarily centered taxonomy of organisms.

Properties of time domain parameters of the vibration signal have been extensively studied for the fault diagnosis of rolling element bearings (REB). Parameters like kurtosis and Envelope Harmonic-to-Noise Ratio are most widely applied in this field and some important progress has been made. However, since only one-sided information is contained in these parameters respectively, problems still exist in practice when the signals collected are of complicated structure and/or contaminated by strong background noises. A new parameter, named Shock pulse index (SPI), is proposed in this paper. It integrates the mutual advantage of both parameters above and can help effectively identify fault related impulse components under the interference of strong background noises, unrelated harmonic components and random impulses. The SPI optimizes the parameters of Maximum Correlated Kurtosis Deconvolution (MCKD), which is used to filter the signals under consideration. Finally, the interested transient information contained in the filtered signal can be highlighted through demodulation with Teager Energy Operator (TEO). Fault related impulse components can therefore be extracted accurately. Simulations and experiment analyses verify the effectiveness and correctness of the SPI.

Bacteriophages (phages) are potential alternatives to chemical antimicrobials against pathogens of public health significance. Understanding the diversity and host specificity of phages is important for developing effective phage biocontrol approaches. Here, we assessed the host range, morphology, and genetic diversity of eight Salmonella enterica phages isolated from a wastewater treatment plant. The host range analysis revealed that six out of eight phages lysed more than 81% of the 43 Salmonella enterica isolates tested. The genomic sequences of all phages were determined. Whole genome sequencing data (WGS) data revealed that phage genome sizes ranged from 41 to 114 kb with GC contents be-tween 39.9 and 50.0 %. Two of the phages SB13 and SB28 represent new species Epsep-timavirus SB13 and genera Macdonaldcampvirus, respectively as designated by the In-ternational Committee for the Taxonomy of Viruses (ICTV) as per genome based taxonomic classification. One phage (SB18) belonged to the Myoviridae morphotype while the re-maining phages belonged to the Siphoviridae morphotype. The gene content analyses showed that none of the phages possessed virulence, toxin, antibiotic resistance, type I-VI toxin-antitoxin modules or lysogeny genes. Three (SB3, SB15 and SB18) out of the eight phages possessed tailspike proteins. Whole genome-based phylogeny of the eight phages with their 113 homologs revealed three clusters A, B, C and seven subclusters (A1, A2, A3, B1, B2, C1 and C2). While cluster C1 phages were predominantly isolated from animal sources, cluster B contained phages from both wastewater and animal sources. The broad host range of these phages highlights their potential use to control the presence of S. enterica in foods.

Rett syndrome (RTT) is an X-linked neurodevelopment disorder associated with the single monogenic mutation in methyl-CpG binding protein 2 (MeCP2) in up to 95% of cases. The growing number of genome-wide association studies and incomplete concordance for autoimmune diseases in monozygotic twins concur to support the involvement of environmental factors, like infectious agents or chemicals, in the breakdown of tolerance leading to autoimmunity. In fact, the coexistence of a perturbation of the immune system in RTT patients has been previously hypothesized. We herein explored the hypothesis that an autoimmune component derived from environmental bacterial infection of non typeable Haemophilus influenzae may coexist in RTT. At this purpose we screened sera from RTT syndrome patients, non-RTT pervasive developmental disorders patients and healthy controls with the hyperglucosylated adhesin protein HMW1ct(Glc) used as a precise antigen in ELISA in order to identify specific antibodies to N-glucosylation sites. Results showed that HMW1ct(Glc) is able to significantly discriminate antibodies among RTT sera and controls. Competitive ELISA confirmed the specific interaction between antibodies characteristic of RTT syndrome and the N-glucosylation motifs of the bacterial adhesin protein HMW1ct(Glc).

Background: The pandemic caused by the SARS-CoV-2 virus demonstrated the importance of prevention through a healthy diet and lifestyle, the most vulnerable people being those with severe chronic conditions, those who are overweight, and those with an unbalanced immune system. Methods: The evaluation of the eating habits and lifestyle of the Romanian population in the post-pandemic period was carried out based on a cross-sectional observational study with the help of a questionnaire. Results: 4704 valid answers were registered (3136 female and 1568 male respondents). Among the respondents, most of them belong to the young population, 2892 between the ages of 18 and 40, i.e., 61.5%. Most male respondents are overweight (1400) and obese (780). Most respondents indicated a tendency to consume 1-2 meals per day irregularly (p=0.6167). Only 974 respondents adopted a healthy diet, and 578 a healthy lifestyle. Conclusion: The present study reports low adherence to a healthy diet (20.7%) and healthy lifestyle (12.28%), especially among the young population (< 30 years). In the current context, it reports a reduced tendency to consume vegetables and fruits among the population, below the daily average recommended by the nutrition guidelines, a tendency towards sedentary behavior, and even deficient hydration of some of the respondents; these negative aspects can create a long term a series of nutritional and psycho-emotional imbalances. Our results evidence that complex surveys among the population are regularly required to investigate nutritional or lifestyle deficiencies; moreover, it could be helpful in further educational measures in nutrition, food, and environmental safety.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

L-gulonolactone oxidase enzyme (GULO) catalyzes the last step of L-ascorbic acid (vitamin C) biosynthesis. This enzymatic activity is lost in primates. The full-length rat GULO has been previously produced in plants and demonstrated to be active. In this study, we compare activity of two variants of GULO produced in Escheriachia coli cells, full-length rat GULO (fGULO) and its C-terminal catalytic domain (cGULO). The expression and purification of the recombinant proteins were optimised and their biological activity was confirmed by two methods, the GULO activity assay in the protein extracts and the ‘in-gel’ staining for GULO activity. Both variants of recombinant GULO were biologically active in both assays. However, cGULO is more promising than fGULO for ascorbic acid production because it is more efficiently produced by bacteria.

Obesity is a highly prevalent chronic disease characterized by excessive weight gain and fat accumulation. There is growing evidence that Lactiplantibacillus plantarum strains with bile salt hydrolase (BSH) activity are effective in preventing and alleviating obesity. However, few of them has confirmed the anti-obesity effect of BSH by gene deletion. In this study, 23 BSH-positive Lp. plantarum strains were screened by bile salt precipitation halo assay. Among these strains, Lp. plantarum Lp20 showed the highest BSH activity with a hydrolysis rate to glycodeoxycholic acid (GDCA) by 91.62%. Genomic sequencing and bioinformatics analysis indicated that gene bsh1 was associated with BSH activity of Lp. plantarum Lp20 and gene deletion of bsh1 confirmed the role of Bsh1 in GDCA hydrolysis. To investigate if the Bsh1 from Lp. plantarum Lp20 could alleviate obesity, the wild type and bsh1 deletion mutant strains were administered daily for 8 weeks to diet-induced obese mice, respectively. Compared with mutant strain, the wild type strain Lp20 significantly reduced body weight gain, inguinal white adipose tissue and mesenteric fat mass in obese mice. In addition, Lp20 also reduced serum total cholesterol levels and LDL-C by 20.8% and 33.3%, respectively. Furthermore, the recovered liver steatosis was only observed in Lp. plantarum Lp20 treated mice. Taken together, the bile salt hydrolase Bsh1 from Lp. plantarum Lp20 was a key functional factor on ameliorating HFD-induced obesity by reducing cholesterol levels and suppressing adipogenesis in mice.

The quality of healthcare services is a very important indicator of social welfare in developed and emerging countries. Good quality levels are critical to ensuring patient safety, improving health outcomes, increasing patient satisfaction, optimizing resource utilization, and meeting regulatory requirements. The stable and sustainable operation of medical institutions urgently requires the establishment of a reliable and effective medical quality performance evaluation platform. However, the complexity of the evaluation process, involving numerous evaluators and the consideration of different subjective and objective criteria, poses significant challenges and essentially constitutes a group multi-criteria decision-making problem. This article uses the overall medical environment of the institution, medical service attitude, medical security, administrative service measures, etc. as measurement standards to deal with this challenge. It proposes a medical service quality measurement model suitable for both qualitative and quantitative analysis. In view of the heterogeneity of information, the two-tuple fuzzy language calculation method is introduced to enable evaluators to skillfully manage diverse information and effectively avoid potential information omission problems in the subjective evaluation integration process. The effectiveness and feasibility of the model were demonstrated by applying it to the operational framework of a medical institution in central Taiwan.

The importance of frailty in older people is getting constant recognition as an important aspect both in terms of public health, as well in personal level for the appropriate management of an older person health condition. This is reflected by the continuously increasing number of research studies carried out in several settings across different countries. Sometimes this is very solid, but in other cases there is a considerable gap in terms of accurate and well grounded documentation of frailty status. This is the case in Greece, where we are missing clinically validated tools to approach frailty. We are missing frailty screening tools, such as for instance PRISMA 7, the gold standard tool of Fried criteria is somehow problematic since the question referring to physical activity originates from a questionnaire that has not been translated and validated, while Clinical Frailty Scale has been validated for the translation but not for the capacity to detect frailty. Aim of this study is to validate these tools for their accuracy to detect frailty by using a measurable index of frailty, previously proposed for use in clinical studies: the Short Physical Performance Battery (SPPB). 74 male and female participants have been evaluated for their frailty status using different tools. We observed that PRISMA 7 translation detects frailty only when one question is removed at a cut-off of ≥ 2 and indicated a sensitivity of 88.1%, and specificity of 99.9% with a good correlation with SPPB measurements (r = 0.858; p < 0.001). When CFS was validated using SPPB it demonstrated a very good correlation (r = -0.838; p < 0.001 respectively) as it was the case for the modified Fried Criteria (r = -0.725; p < 0.001). All items demonstrated a good correlation between them. We can here propose that we can accurately assess frailty status in the community setting by using a modified version of Fried criteria, Clinical Frailty Scale translation in Greek and we can screen for frailty by using the Greek translation of PRISMA 7 only after removing the item 6 of the questionnaire.

Silver ion (Ag+) are recognized for their potent antibacterial properties; however, their utilization in food preservation is restricted by factors such as inadequate stability, a transient antibacterial impact, and the potential for human absorption. Hydrogel-based antibacterial agents are capable of exerting their antibacterial effects by establishing appropriate microenvironments, which facilitate the efficient delivery of antimicrobial molecules to the contaminated regions of food. In previous studies, we observed that chitosan (CS) and silver nitrate (AgNO3) were able to reduce Ag+ to silver nanoparticles (AgNPs) with enhanced antibacterial properties. This not only significantly extended the stability of the antibacterial agent but also demonstrated exceptional inhibitory capabilities against pathogenic bacteria, including common grape contaminants such as P. expansum, A. niger, and B. cinerea. Utilizing ultrasound-induced complexation technology, this study has successfully synthesized a chitosan-silver (CS-AgNPs) hydrogel. The efficacy of this hydrogel against the pathogenic fungus responsible for jujube black spot disease has been thoroughly investigated. The morphology structures of CS-AgNPs hydrogels were characterized by TEM, FTIR and UV-vis. The results indicated that AgNPs ranging from 80 to 110 nm were uniformly dispersed within the gel matrix and remained stable for extended periods at room temperature. In vitro antibacterial assays and fractional inhibitory concentration index (FICI) studies revealed that the pronounced antibacterial efficacy of the CS-AgNPs hydrogel was primarily attributed to the additive antibacterial effect of CS and AgNPs. These insights underscore the significant potential of CS-AgNPs hydrogels in combating fungal diseases of jujube, offering innovative strategies and materials for the management of agricultural pathogens.

Graphene quality for use in biosensors was assessed in fabricated chips by a set of methods that includes atomic force microscopy (AFM), Raman spectroscopy, and low-frequency noise. It is shown that local areas of residues on the graphene surface, which arisen due to the interaction of graphene with a photoresist at the initial stage of chips development, leads to a spread of chips resistance (R) within 1-10 kΩ and to an increase in the root mean square (RMS) roughness up to 10 times that can significantly impair reproducibility of graphene parameters in biosensors chips. It was observed that the control of the photoresist residues after photolithography (PLG) by AFM and subsequent additional cleaning allow reducing the spread of R values in chips to 1–1.6 kΩ and obtaining RMS roughness similar to the roughness in pristine graphene before PLG. Monitoring of the spectral density of low-frequency voltage fluctuation (SU), which provides integral information about the defect system and quality of the material, makes it possible to identify chips with low graphene quality and with inhomogeneously distributed compressive stresses areas by the type of frequency dependence SU (f).

Keenjhar Lake is the main source of drinking water for the metropolitan city of Karachi. The release of untreated wastewater from Kotri industrial area and other sources have made the lake water polluted. This study was subjected to determine the impacts of such pollutant sources on the water quality of Keenjhar Lake. The study involves the analysis of water quality parameters of Keenjhar Lake and its Feeding source (KB Feeder). The sampling sites were selected based on the sources of contamination. The water samples are tested for physical, chemical and microbiological parameters. The result of water analysis indicates the contamination level of the lake is quite alarming for the sites of Kotri effluent and WAPDA colony where Total Dissolved Solids (TDS), Chloride and other ionic metals were quite higher in concentration than other sites. These sites are also contaminated with Fluoride and Arsenic which are carcinogenic elements. The study reveals that the contamination level of feeding source is causing big non-reversible damage to the lake if continued to be uncontrolled. This contamination is mainly due to the release of toxic metals and ions in the KB feeder caused by human carelessness.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

Porins are crucial proteins located in the outer membrane that directly influence antimicrobial resistance mechanisms and virulence in bacteria. In this study, a porin gene (Vp-porin) was cloned in V. parahaemolyticus, and the function of Vp-porin on biological characteristics and virulence was investigated. The results of sequence analysis showed that Vp-porin is highly conserved in Vibrio spp. and the predicted 3D structure showed it could form a transmembrane channel with 20 β barrel. Membrane permeabilization provides evidence that membrane integrity of ∆Vp-porin was damaged and the sensitivity to tetracycline, polymyxin B, rifampicin and cephalothin of ∆Vp-porin obvious increased. In addition, loss of Vp-porin damaged motility due to down-regulated flagellar synthesis. Besides, ∆Vp-porin exhibited attenuated cytotoxicity to Tetra-hymena. The relative survival rate of Tetrahymena infection with ∆Vp-porin was 86%, which is much high than that with WT (49%). Take together, Vp-porin in V. parahaemolyticus plays various roles in biological characteristics in membrane integrity, antimicrobial resistance and motility, and contributes to virulence.

Pardosa pseudoannulata is one of the most common wandering spiders in agricultural fields and a potentially good bioindicator for heavy metal contamination. However, little is known about the mechanism by which spiders respond to heavy metals at the molecular level. In this study, high-throughput transcriptome sequencing was employed to characterize the de novo transcriptome of the spiders and to identify differentially expressed genes (DEGs) after cadmium exposure. We obtained 60,489 assembled unigenes, 18,773 of which were annotated in the public databases. Ultimately, 3450 cDNA simple sequence repeats were identified and validated as potential molecular markers in the unigenes. A total of 2939, 2491 and 3759 DEGs were detected among the three libraries of two Cd-treated groups and the control. Functional enrichment analysis revealed that metabolism processes and digestive system function were predominately enriched in response to Cd stress. At the cellular and molecular levels, significantly enriched pathways in lysosomes and phagosomes as well as replication, recombination and repair demonstrated that oxidative damage resulted from Cd exposure. Based on the selected DEGs, certain critical genes involved in defence and detoxification were analysed. These results may elucidate the molecular mechanism underlying spiders' responses to heavy metal stress.

Bicyclic peptides have attracted the interest of pharmaceutical companies because of their remarkable properties putting them on a new path in medicine. Their conformational rigidity that improves proteolytic stability, leads to rapid penetration into tissues via any possible route of administration and elimination, occurring by renal metabolism, is of great importance for people with a history of liver diseases. In addition, each ring can function independently, making them extremely versatile molecules for further optimization. In this paper we compared the potentiometric and spectroscopic properties studied by UV-Vis, MCD, and EPR, of four synthetic analogues of the bi-cyclic peptide c(PKKHP-c(CFWKTC)-PKKH). In particular we correlated the structural and spectral properties of complexes with coordinating abilities toward Cu(II) ions of MCL (Ac-PKKHPc(CFWKTC)PKKH-NH2) that contains the unbinding cycle and N- and C-terminal linear parts, with two histidine residues, one per part; two monocyclic ligands containing one histidine residue, both in the N-terminal position i.e., MCL2 (Ac-PKKHPc(CFWKTC)PKKS-NH2) and in the C-terminal position i.e., MCL3 (Ac-PKKSPc(CFWKTC)PKKH-NH2), respectively, and the linear structure LNL (Ac-PKKHPSFWKTSPKKH-NH2).

The water quality index (WQI) and irrigational index for groundwater were studied in the northeastern section of the Manipur Valley in northeast India. Water samples were collected in 2022 during the pre-monsoon season. To compute the water quality index for drinking water, the basic chemical parameters of total hardness, pH, electrical conductivity, total dissolved solids, Ca2+, Na+, Fe, Mg2+, Mn, Cl-, and HCO3, were used. The assessment of bacteriological quality is also done, which is crucial for overall water quality evaluation, alongside physical and chemical analyze. For determining irrigation suitability, irrigational indices such as sodium absorption ratio, sodium percentage, and magnesium hazard were calculated. WQI, %Na+, SAR, magnesium hazard, permeability Index and total hardness indicate that most water samples are harmless for irrigation and drinking purpose. They have affirmative relationships indicating that these characteristics are interdependent. Approximately 25% of the Piedmont zone groundwater is found to be unfit for agricultural and drinking usage. The encrustation of gypsum, halite, and evaporation into the Disang shares accelerate the dissolution of ions in Piedmont water, resulting in quality degradation. According to Gibbs plots, Durov Scatter Plot, and Hill Piper Trilinear Diagram of water dominated the rock-weathering process, while hydro chemical facies progressed from the beginning to the intermediate stage of Chadha's graphical representation illustrates the progression of hydro chemical processes in surface water. Therefore, proper integrated water resource management and development are required for effective water resource utilization, particularly around the Piedmont zone. To prevent a water crisis, groundwater resources must be managed sustainably. The current study also concentrated on a bibliometric examination of groundwater management and access to gauge the state of the field.

The European Union Water Framework Directive (2000/60/EC; WFD) aims to achieve a good ecological and chemical status of all bodies of surface water by 2027. The development of an integrated guidance on surface water chemical monitoring (e.g. WFD Guidance Document No. 7/19) has been transferred into national German law (Ordinance for the Protection of Surface Waters, OGewV). For the majority of compounds, this act requires a monthly sampling frequency to assess the chemical water quality status of a surface water body. To evaluate the representativeness of the sampling strategy under the OGewV, high-frequency online monitoring data is investigated under different sampling scenarios and compared with current, monthly grab sampling strategy. About 23 million data points were analyzed for this study, three chemical parameters (dissolved oxygen, nitrate-nitrogen, chloride concentration) and discharge data were selected from four catchment of different sizes ranging from 51391 km² to 84 km² (Elbe, Vereinigte Mulde, Neiße and two stations at Lockwitzbach). In this paper we proposed short-term online-monitoring (STOM) as a sampling alternative. STOM considers the placement of online sensors over a limited duration and return interval. In general we: (I) compare the results of conventional grab sampling with STOM, (II) investigate the different performance of STOM and grab sampling using discharge data as proxy for analyzing event-mobilized pollutants and (III) investigate the related uncertainties and costs of both sampling methods. Results show, that STOM outperforms grab sampling for parameters where minimum/maximum concentrations are required by law as the probability to catch a single extreme value is higher with STOM. Furthermore, parameters showing a pronounced diurnal pattern, like dissolved oxygen, are also captured considerably better. The performance of STOM showed no substantial improvements for parameters with small concentration variability, as nitrogen-nitrate The analysis of discharge events as a proxy parameter for event-mobilized pollutants proved that the probability of capturing samples during events is significantly increased by STOM.

Objective Image Quality Assessment (IQA) measures are playing an increasingly important role in the evaluation of digital image quality. New IQA indices are expected to be strongly correlated with subjective observer evaluations expressed by MOS/DMOS scores. One such recently proposed index is the SuperPixel-based SIMilarity (SPSIM) index, which uses superpixel patches instead of the rectangular pixel grid.The authors in this paper have been proposed three modifications of SPSIM index. For this purpose, the color space used by SPSIM was changed and the way SPSIM determines similarity maps was modified using methods derived from the algorithm for computing the MDSI index. The third modification was a combination of the first two. These three new quality indices were used in the assessment process. The experimental results obtained on many color images from five image databases demonstrated the advantages of the proposed SPSIM modifications.

Video quality assessment (VQA) plays an important role in video applications for quality evaluation and resource allocation. It aims to evaluate the video quality consistent with the human perception. In this letter, a hierarchical gradient similarity based VQA metric is proposed inspired by the structure of the primate visual cortex, in which visual information is processed through sequential visual areas. These areas are modeled with the corresponding measures to evaluate the overall perceptual quality. Experimental results on the LIVE database show that the proposed VQA metric significantly outperforms the state-of-the-art VQA metrics.

The combination of immunoPET—where an antibody (Ab) is labeled with an isotope for PET imaging—and radioimmunotherapy (RIT), using the same antibody with a therapeutic isotope, offers significant advantages in cancer management. ImmunoPET allows non-invasive imaging of antigen expression, which aids in patient selection for a subsequent radioimmunotherapy. It also facilitates the assessment of tumor response to therapy, allowing for treatment adjustments if necessary. In addition, immunoPET provides critical pharmacokinetic data, including antibody biodistribution and clearance rates, which are essential for dosimetry calculations and treatment protocol optimization. There are still challenges to overcome. Identifying appropriate target antigens that are selectively expressed on cancer cells while minimally expressed on normal tissues remains a major hurdle to reduce off-target toxicity. In addition, it is critical to optimize the pharmacokinetics of radio-labeled antibodies to maximize tumor uptake and minimize normal tissue uptake, particularly in vital organs such as the liver and kidney. This approach offers the potential for targeted and personalized cancer therapy with reduced systemic toxicity by exploiting the specificity of monoclonal antibodies and the cytotoxic effects of radiation. However, further research is needed to address remaining challenges and to optimize these technologies for clinical use.

Quality of life (QoL) assessments are integral to cancer care, yet their effectiveness in providing essential information for supporting survivors varies. This study aimed to elucidate key indicators of QoL among colorectal cancer survivors from the perspective of healthcare professionals, and to evaluate existing QoL questionnaires in relation to these indicators. Two studies were conducted: a Delphi study to identify key QoL indicators and a scoping review of questionnaires suitable for colorectal cancer survivors. Fifty-four healthcare professionals participated in the Delphi study's first round, with 25 in the second. The study identified two primary QoL domains (Physical and Psychological) and 17 subdomains deemed most critical. Additionally, a review of 12 questionnaires revealed two instruments assessing the most important general domains. Findings underscored a misalignment between existing assessment tools and healthcare professionals' clinical priorities in working with colorectal cancer survivors. To enhance support for survivors' QoL, efforts are needed to develop instruments that better align with the demands of routine QoL assessment in clinical practice.

Alzheimer’s disease (AD) is an age-associated neurodegenerative disorder. A wealth of evidence indicates that the amyloid β (Aβ) aggregates result from dyshomeostasis between Aβ production and clearance, which plays a pivotal role in the pathogenesis of AD. Consequently, therapies targeting Aβ reduction represent a promising strategy of AD intervention. Tetramethylpyrazine nitrone (TBN) is a novel tetramethylpyrazine derivative with the potential for the treatment of AD. Previously, we demonstrated that TBN markedly improved cognitive functions and reduced Aβ, APP, BACE 1 and hyperphosphorylated tau levels in 3 × Tg-AD mice. However, the mechanism by which TBN inhibits Aβ deposition still unclear. In this study, we employed the APP/PS1 mice treated with TBN (60 mg/kg, ig, bid) for six months and N2a/APP695swe cells treated with TBN (300 μM) to explore the mechanism of TBN on the Aβ reduction. Our results indicated that TBN significantly alleviated cognitive impairment and reduced Aβ depositions in APP/PS1 mice. Further investigation of the underlying mechanisms revealed that TBN decreased the expression of APP and BACE1, activated the AMPK/mTOR/ULK1 autophagy pathway and inhibited the PI3K/AKT/mTOR/ULK1 autophagy pathway, as well as decreased the phosphorylation levels of JNK and ERK in APP/PS1 mice. Moreover, TBN was found to significantly reduce the mRNA levels of APP and BACE1, as well as those of SP1, CTCF, TGF-β, and NF-κB, transcription factors involved in regulating gene expression. Additionally, TBN was observed to decrease the level of miR-346 and increase the levels of miR-147 and miR-106a in the N2a/APP695swe cells. These findings indicate that TBN may reduce Aβ levels likely via reducing APP expression by regulating APP gene transcriptional factors and miRNAs, reducing BACE1 expression, and promoting autophagy activities.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

The aim of the study was to test the significance of the EPT index in the water quality assessment of three types of water bodies in hilly and mountainous region of Serbia. The aquatic macroinvertebrate community was dominated by the group of insects, of which 95 taxa represent the EPT group. We compared the obtained values of biological indices used for the assessment of water quality according to the national legislation with the overall status assessment represented by the ecological quality classes (EQC). The results of the Spearman correlation test showed a negative correlation of EQC with the EPT index, BMWP score, H', total number of taxa and number of sensitive taxa, while a positive correlation was observed for the values of SI and Tubificinae %. The values of EQC and biological indices were subjected to principal component analysis (PCA). The results showed that the parameters that contributed most to the differences were the EPT index, the BMWP score and the number of sensitive taxa. The results indicate that the EPT index is an excellent indicator of changes in water quality and an important tool for the ecological categorization of water bodies in mountain regions.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

IT auditing quality has been defined by results obtained in the process. Meanwhile, multiple studies have been done to enhance it therefore, it continues to be a topic interest and research so it is worth mentioning that its quality relies on trained competent auditors and experts able to develop a process correctly, adapting to clients and to manage auditing inherent risks According to results from the IT audit, low quality and security levels have been identified in terms of the human, technical and contextual factors, affecting audit quality. The objective of this investigation is to identify metrics and to determine their own corresponding factor applying an exploratory type of research. In order to achieve such aim, a targeted survey was designed and implemented at the Institute of Internal Auditors of Ecuador since they have the knowledge and expertise in the field. A factor analysis statistics technique was applied to data gathered to verify that it relates to the identified factors as dimensions are reduced, thus the most impacting metrics may assess the quality of IT audits. Analysis results yielded a mean score for each one of the assessed metrics, concluding that the technical factor is the most significative since it relates roles and task performance during the auditing process as well as control proce-dures. Finally, most auditing quality-related issues are mainly the outcome of an inferior management auditing process, therefore it is crucial that collegiate groups and professionals in the field validate the auditing process.

The Saudi Vision 2030 is critical to boosting national development, notably in the construction industry. The construction industry is getting a lot of attention in a variety of ways, the most visible of which is the promotion of best practices, including project management office (PMO) applications. Hail province, like others, is experiencing project delivery issues. Thus, the purpose of this research is to explore the suitable PMO model for Hail public construction projects. A literature review included the drive factors for establishing PMO in construction firms, as well as PMO models and typologies that describe functions. Therefore, those drive factors and PMO models were subjected to a focus group to explore their suitability in the context of Hail. The research findings reveal that the Enterprise PMO is the main for Hail public construction pro-jects, followed respectively by the Program Management Office model and the Project Management Center of Excellence (PMCOE). This method of selection a PMO model is driving construction companies and related businesses to change in order to improve the sector while also ad-dressing construction project delivery challenges in Hail province.

Grain quality, cooking quality and nutritional quality traits are some of the major attributes that enhance uptake and utilisation of improved cowpea varieties. Therefore, there is need for a better understanding of the genetic variation and inter-relationships among these quality traits in cowpea to integrate them in cowpea breeding programs. The study was conducted to determine genetic variability among 306 cowpea genotypes for grain quality, cooking quality and nutritional quality traits and to understand the interrelationships among these traits for exploitation in breeding programs. The results showed highly significant differences (P

Air quality has been a major concern throughout the world, Nigeria inclusive. The monitoring of air quality involves indoor and outdoor air quality. In this study, our concern was on indoor air quality. The aim of this study was to assess the air quality of residential homes (17), classrooms (3), hospitals (2), offices (5), Shops (2), and laboratories (5) in Akure, Nigeria in terms of formaldehyde (HCHO), total volatile organic compound (TVOC), Particulate matter (PM_1.0; PM_2.5, and PM₁₀). A Multifunction Air Detector was used for the assessment using the manufacturers’ procedures and the locations were identified using a Mini GPS. The results revealed as follows: HCHO (0.001-0.030 mg/m³), TVOC (0.003-362 mg/m³), PM_1.0 (004-014 µg/m³), PM_2.5 (006-020 µg/m³), and PM₁₀ (006-022 µg/m³). The results obtained were below the 24 h pollution recommended standards (0.1 mg/m³- HCHO; TVOC; 10-20 μ/m³ PM) of EPA and WHO. Statistically, there were correlations within the pollutants and weather. The Indoor air quality (IAQ) depicted the areas as ‘good,’ and toxicity potential (TP) were below unity. Although the locations looked safe, it is recommended that constant monitoring of the indoors should be ensured and proper ventilation should be provided.

With an increased interest in applications that require a clean background image, such as video surveillance, object tracking, street view imaging and location-based services on web-based maps, multiple algorithms have been developed to reconstruct a background image from cluttered scenes. Traditionally, statistical measures and existing image quality techniques have been applied for evaluating the quality of the reconstructed background images. Though these quality assessment methods have been widely used in the past, their performance in evaluating the perceived quality of the reconstructed background image has not been verified. In this work, we discuss the shortcomings in existing metrics and propose a full reference Reconstructed Background image Quality Index (RBQI) that combines color and structural information at multiple scales using a probability summation model to predict the perceived quality in the reconstructed background image given a reference image. To compare the performance of the proposed quality index with existing image quality assessment measures, we construct two different datasets consisting of reconstructed background images and corresponding subjective scores. The quality assessment measures are evaluated by correlating their objective scores with human subjective ratings. The correlation results show that the proposed RBQI outperforms all the existing approaches. Additionally, the constructed datasets and the corresponding subjective scores provide a benchmark to evaluate the performance of future metrics that are developed to evaluate the perceived quality of reconstructed background images.

Quite a number of cottonseed varieties are existed. The seeds of each variety produce a different amount of gossypol as a natural toxic compound. The increased interest in this natural product and its toxic effects were enhanced the demand for establishing simple silica-gel-based methods for its isolation, purification, and characterization. Historically, silica gel plays a significant role in isolation and purification of many different natural products. Silica gel is variants and can intro-duce a lab, simple tool for tracking a compound in certain plants during its purification process. In this study, gossypol was isolated and purified in the form of yellow crystals as gossypol acetic ac-id. Several methods and tools were used for its characterization including TLC, preparative TLC, silica gel column, UV/IR spectrophotometer and HPLC (Robust spherical silica gel). A compara-tive study between its amounts in both Egyptian and Chinese varieties were performed. Under the experimental condition, the Egyptian cottonseeds contain 8.705 gm/kg, while the Chinese contains 5.395 gm/kg. Thin Layer Chromatography (TLC) had been flourished the science of the phytochemistry and still popular till nowadays and is recommended for fast, accurate, and inex-pensive evaluation and quantification of gossypol. It is recommended to isolate and purify gossy-pol as gossypol acetic acid using optimized combined methods used in this study. Using Silica gel different protocols will assist and facilitate the parallel comparison and save the compact column from any unexpected contaminants during the purification steps. During each step the silica gel itself could be simply removed by paper filtration.

The decline of fossil fuels, the increase of greenhouse gases and the global demand for energy are driving the search for alternative energy sources. Anaerobic digestion is a promising technology because it can convert organic biomass into biogas. As the climate warms, there is an increase in biomass of plant origin in water bodies, and ecosystems are unable to clean themselves. This work aims to show that macroalgae and aquatic plants can be an excellent raw material for biogas production. By mixing them with co-substrates such as cattle manure, higher biogas and methane yields can be obtained. When Cladophora glomerata and Zostera marina macroalgae are mixed with cattle manure, the biogas yield is up to 458.8 mL/gVS and 397.9 mL/gVS, respectively. Methane concentration remained high and reached 62.4%–64.1%. The obtained research results show the high energy value of biogas and the energy potential of biomass. Macroalgae increased the energy potential of biogas to 22.9 MJ/m3, and the energy potential of biomass reached 2.40 MJ/Kg. Due to its high energy value, biogas produced from the considered substrates can be an excellent alter-native to fossil fuels. Integrating aquatic macroalgae into anaerobic digestion is a promising approach for a waste-free marine and freshwater system.

This work evaluates the surface water quality in terms of physico-chemical parameters of the Brahmani River, Odisha using statistical analysis involving the calculation of correlation coefficient and regression equation. Besides this, the work also highlights and draws attention towards the “Water Quality Index” in a simplified format which may be used at large and could represent the reliable picture of water quality. Surface water quality data is taken from OSPCB of various location i.e. Panposh D/S, Rourkela D/S, Rengali, Talcher U/S, Kamalanga D/S, Bhuban, Pattamundai and was assessed for summer, monsoon, winter for the years 2011, 2012, 2013, 2014 and 2015. Average of values, minimum of values and maximum of values of water quality parameters were obtained seasonally over the above mentioned years. Besides this, the standard deviation for the water quality parameters was also obtained for water quality parameters namely pH, Temperature, DO, TDS, Alkalinity, EC, Na+, Ca2+, Mg2+, K+, F-, Cl-, NO3-, SO42- and PO42-. Seasonal changes in various physical and chemical parameters were analysed.The values obtained were compared with the guideline values for drinking water by Bureau of Indian Standard (BIS). A systematic correlation and regression study is carried out for three seasons, showed linear relationship among different water quality parameters. This provides an easy and rapid method of monitoring water quality. Highly significant (0.8< r <1.0), moderately significant (0.6< r <0.8) and significant (0.5< r <0.6) correlations between the parameters have been worked out. High correlation coefficient has been observed between TDS,EC-Na+, Ca2+, Cl-, SO42- ; Na+- Cl-. From the collected quantities, certain parameters were selected to derive WQI for the variations in water quality of each designated sampling site. WQI of Brahmani River ranged from 36.7 to 44.1 which falls in the range of good quality of water.Panposh D/S and Rourkela D/S showed poor water quality in summer and winter season. It is shown that WQI may be a useful tool for assessing water quality and predicting trend of variation in water quality at differentlocations in the Brahmani River.

The key goal of the current study was to determine suitable areas of water pumping for drinking and agricultural harvest in Tabriz aquifer, located in East Azerbaijan province, northwest Iran. In the study area, groundwater is the key foundation of water for drinking and farming requirements. Groundwater compatibility study was conducted by analyzing Electrical conductivity (EC), Total dissolved solids (TDS), Chloride (Cl), Calcium (Ca), Magnesium (Mg), Sodium (Na), Potassium (K), Sulfate (SO4), Total hardness (TH), Bicarbonate (HCO3), pH, carbonate (CO3) and Sodium Adsorption Ratio (SAR) obtained from 39 wells in the period of 2003 to 2014. For this purpose, the Water Quality Index (WQI) and irrigation water quality (IWQ) index were utilized. The WQI index zoning exposed that the groundwater of the study area for drinking purposes is categorized as excellent, good and poor water. Most drinking water harvested for urban and rural areas are in the class of 'excellent water'. The results revealed that about 37 percent (296 km2) of groundwater has high compatibility, and 63 percent of the study area (495 km2) has average compatibility for agricultural purposes. The trend of IWQ and WQI indexes demonstrates that the groundwater is getting worse over the time.

Infrared thermography is a contactless imaging technique, useful to measure surface temperature at distance which has been widely applied in animal production. The possible applications within the pig husbandry include sow heat detection, reduction of the incidence of neonatal mortality, recognition of febrile state caused by pathogens, study of metabolic efficiency, evaluation of stress caused by heat, by constraints, or by aggressive interaction and meat quality prediction. Even if this technique could be easily influenced by environmental factors, the continuous improvement in the procedures and the decrease in the cost of the equipment will allow in the next future new and more applications in swine farming.

Pancreatic ductal adenocarcinoma (PDAC) represents an extremely aggressive type of cancer due in part to early invasion and metastasis, which in turn involves epithelial-mesenchymal transition (EMT) of the tumor cells. Prompted by the discovery that two PDAC-derived tumor cell lines of the quasi-mesenchymal subtype (PANC-1, MIA PaCa-2) exhibit neuroendocrine differentiation (NED), we asked whether NED is associated with EMT. Using quantitative real-time PCR and immunoblot analysis, we initially verified endogenous expression of various NED markers, i.e., chromogranin A (CHGA), synaptophysin (SYP), somatostatin receptor 2 (SSTR2) and SSTR5 in PANC-1 and MIA PaCa-2 cells. In HPDE6c7 normal pancreatic duct epithelial cells and in BxPC-3, another PDAC cell line with an epithelial phenotype, the expression of CHGA, SYP and neuron-specific enolase 2 (NSE) was either undetectable or much lower than in PANC-1 and MIA PaCa-2 cells. Parental cultures of PANC-1 cells exhibit EM plasticity (EMP) and harbor clonal subpopulations with different EMT phenotypes [Ungefroren et al 2022]. Monitoring the NED state of mesenchymal and epithelial PANC-1 subclones showed that the NE phenotype is more pronounced in M-type clones when compared to E-type ones. Inducing EMT in parental cultures of PANC-1 cells by treatment with transforming growth factor (TGF)-β1 repressed epithelial genes and co-induced mesenchymal and NED genes, except for SSTR5. Surprisingly, treatment with bone morphogenetic protein (BMP)-7 differentially affected gene expression in PANC-1 and MIA PaCa-2 cells. It synergised with TGF-β1 in the induction of vimentin, SNAIL, SSTR2 and NSE but antagonised it in the regulation of CHGA and SSTR5. From these data, we conclude that in EMT of PDAC cells mesenchymal and NED markers are co-regulated, and that mesenchymal-epithelial transition (MET) is associated with a loss of both the mesenchymal and NED phenotypes. Analysing NED in another tumor type, small cell carcinoma of the ovary hypercalcemic type (SCCOHT), revealed that two model cell lines of this disease (SCCOHT-1, BIN-67) do express CDH1, SNAI1, VIM, CHGA, SYP, ENO2 and SSTR2, but that in contrast to BMP-7 none of these genes was transcriptionally regulated by TGF-β1. We conclude that in PDAC-derived tumor cells, NED is closely linked to EMT and TGF-β signaling, which may have implications for the therapeutic use of TGF-β inhibitors in PDAC management.

Abstract: Currently, antibodies are major therapeutic modalities in biopharmaceutical research and development. Because of required high dose for certain clinical applications, antibodies are formulated at high protein concentration for convenience of administration, shipping and storage. We will describe the inter-molecular interactions that can occur in such a crowded environment of high protein concentration. Two types of repulsive interactions, i.e., electrostatic and excluded volume effects, and three types of attractive interactions, i.e., hydrophobic, electrostatic and cross-linking, need to be considered in such a crowded environments. We then show consequences of such inter-molecular interactions, leading to high viscosity, opalescence and phase separation of antibody solutions. Co-solvents are used to control the stability, structure and molecular interactions and thereby to alleviate these solution problems. Among various co-solvents, arginine has been extensively used to suppress protein-protein interactions at high protein concentration. Arginine weakly but extensively interacts with aromatic/hydrophobic groups as well as charged groups on proteins, leading to effective suppression of viscosity, opalescence and phase separation of antibody solution.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

The main purpose of our research is the evaluation of the efficacity of solvent polarity on phenolic composition, as well as the antibacterial, and antioxidant activities of extract of Moroccan Mentha aquatica L., leaves. To attempt these objectives, the HPLC-DAD was used to identify the biomolecules. The total amount of phenolic and flavonoid content was determined using the Folin-Ciocalteu and aluminum trichloride processes as well as the DPPH, RP, and TAC tests were used to evaluate the antioxidant capabilities. In addition, by employing both in vitro and in silico analysis through the microdilution method, the minimum inhibitory concentration (MIC) and minimum bactericidal concentration (MBC) of the extracts were assessed against multidrug-resistant bacteria. Furthermore, the High-Performance Liquid Chromatography (HPLC) analysis indicated that all extracts of M. aquatica were abundant in noteworthy phytochemical compounds, especially gallic acid, vanillic acid, chlorobenzoic acid, quercetin, and kaempferol. Furthermore, the results indicated that the total phenolic content was higher in hydroethanolic extract (62.19 ± 1.19 mg GAE/g DW) in contrast to the acetonic and aqueous extracts (22.22 ± 0.64, and 22.44± 0.57 mg GAE/g DW) respectively. Similarly, the aqueous ethanol extract contained the greatest flavonoid concentration, with values of 29.15± 0.09 mg QE/g DW when compared with the other extracts. The seam extract poses excellent antioxidant power with an IC50 of 0.06 ± 0.00 mg/mL for the DPPH test, and lower RP with EC50 of 80± 0.00 µg/ml when compared with acetonic and aqueous extract (370± 0.00 and 460± 0.01 µg/mL) respectively. Moreover, the hydroethanolic extract has a high level of TAC 75.09± 2.00 mg EAA/g DW, followed by aqueous extract carrying a value of 28.53 ± 1.36 mg EAA/g DW. The antibacterial capacity is ranged between 0.78 ± 0.05 mg/mL and 12.60 ± 0.00 mg/L. The results of the in-silico study demonstrated that quercetin, vanillic acid, and naringenin components contribute to the antioxidant capability. While gallic acid, kaempferol, and quercetin components are attributed to the antibacterial capacity.

The increasing demand for water resources in urban areas, such as Bangladesh, due to population growth is a significant concern. One potential solution under consideration is the use of air conditioning (AC) condensate water. A study conducted at the European University of Bangladesh (EUB) focused on assessing the quality and quantity of AC condensate water from various systems. The results indicate that the collected water generally adhered to the quality standards established for drinking and household use in Bangladesh. Parameters such as pH (averaging 6.8), turbidity (1.08 NTU), total dissolved solids (TDS) (averaging 219 mg/L), iron content (0 mg/L), alkalinity (averaging 41.67 mg/L), arsenic (0 mg/L), chemical oxygen demand (COD) (averaging 3.67 mg/L), biochemical oxygen demand (BOD) (averaging 1.33 mg/L), chloride content (averaging 30.77 mg/L), and other factors were evaluated. Moreover, the AC units at EUB, varying in cooling capacity (1 ton, 2 tons, and 4 tons), produced substantial monthly volumes of 96, 177, and 354 liters of condensate water, respectively. This underscores the potential of AC condensate water as a valuable resource for addressing urban water scarcity. As a result, there is a pressing need for local decision-makers and policymakers to establish well-defined guidelines for the effective utilization of AC condensate water to mitigate water scarcity issues in urban areas.

Ukraine is an associate member of the European Union and in the coming years it is expected that all the data and services already used by European Union countries will become available for Ukraine. An important program, which is the basis for building European monitoring services for Smart Cities, is the Copernicus program. The two most important services of this program are Copernicus Land Monitoring Service (CLMS) and Copernicus Atmosphere Monitoring Service (CAMS). CLMS provides important information on Land Use in Europe. In the context of Smart Cities, the most valuable one is the Urban Atlas service, which is related to local CLMS services and provides a detailed digital city plan in vector form, which is segmented into small functional areas classified by the CORIN nomenclature. The Urban Atlas is a geospatial layer with high-resolution, which is built for all European cities with a population of more than 100,000 that combines high-resolution sat-ellite data, city segmentation by blocks and functional areas, important city infrastructure, etc. This product is used as a basis for city planning and obtaining analytics on the most important indicators of city development including air quality monitoring. For Ukraine, such geospatial products are not provided under the Copernicus program. It is important to start work on its development and implementation as early as possible, so that when the first city atlas appears, Ukraine will be ready to work with it together with the European community. This requires preparing the basis for na-tional research and training national stakeholders and users to use this product. To make this happen it’s necessary to have national geospatial product, which can be used as an analogue of the city atlas. In this article authors analyzed the existing methods of air quality assessment and assessment of the SDG indicator 11.6.2 achieving for European cities, based on which the indicator 11.6.2 for Ukraine for 5 years was evaluated for the first time. The obtained results are analyzed and the values of indicator 11.6.2 for Ukraine are compared with European countries.

Ultramafic rocks become promising candidates for carbon sequestration by enhanced carbon dioxide (CO2) mineralization strategies due to their highly CO2-reactive mineral composition and its abundant availability. This study reports a mineralogy and microtextures of a representative ultramafic rock from the Ma-Hin Creek in northern Thailand and observes evidence of CO2 mineralization occurring through the interaction between CO2 and the rock with the existence of water under ambient conditions. After sample collection, rock description was determined by optical petrographic analysis. The rock petrography reveals a cumulated wehrlite comprising over 50% olivine and minor amounts of clinopyroxene, plagioclase, and chromian spinel. Approximately 25% of the wehrlite has altered to serpentine and chlorite. A series of CO2 batch experiments were conducted on six different rock sizes at a temperature of 40°C and pressure of 1 atm over five consecutive days. The post-experimental products were dried, weighed, and geochemically analyzed to detect changes in mineral species. Experimental results showed that product weight and the presence of calcite increased with reducing grain size. Additionally, the modal mineralogy of the wehrlite theoretically suggests a potential CO2 uptake of up to 53%, which is higher than the average uptake values of mafic rocks. These findings support the suitable rock investigation approach and the preliminary assessment of carbon mineralization potential, contributing to enhanced rock weathering techniques for CO2 removal that could be adopted by mining and rock supplier industries.

Prediction of protein-ligand binding affinities is crucial for computational drug discovery. A number of deep learning approaches have been developed in recent years to improve the accuracy of such affinity prediction. While the predicting power of these systems have advanced to some degrees depending on the dataset used for model training and testing, the effects of the quality and quantity of the underlying data have not been thoroughly examined. In this study, we employed erroneous datasets and data subsets of different sizes, created from one of the largest databases of experimental binding affinities, to train and evaluate a deep learning system based on convolutional neural networks. Our results show that data quality and quantity do have significant impacts on the prediction performance of trained models. Depending on the variations in data quality and quantity, the performance discrepancies could be comparable to or even larger than those observed among different deep learning approaches. In particular, the presence of proteins during model training leads to a dramatic increase in prediction accuracy. This implies that continued accumulation of high-quality affinity data, especially for new protein targets, is indispensable for improving deep learning models to better predict protein-ligand binding affinities.

A very important role in determining the quality of water is the assessment of its microbiological quality. Water quality control, which could pose a direct threat to human health and life, is performed in the case of water produced at the water treatment plants, tap water or water in swimming pools. However, these traditional methods used to assess its quality are laborious and time consuming. In emergency and incidental situations, in the era of terrorist threats, the need for quick, reliable and reproducible microbiological determinations seems to be essential. In this study, an attempt was made to compare various methods of assessing the microbiological quality of water. The assessment was carried out for waters with different microbiological characteristics: surface waters, rainwater, groundwater, and water supply. The evaluation was carried out using traditional culture methods and high-speed methods: flow cytometry and luminometry. The analysis of microbiological parameters were the basis for the statistical analysis. The conducted microbiological analysis of various types of water, along with their statistical evaluation, showed different dependencies for each of the analysed waters.

A Water demand per capita will rise in the Arab world as a result of climate change and population expansion. One of the most important aims in coping with population increase around the world is to conserve water supplies. As a result, the Kingdom of Saudi Arabia constructed Al Wajeed Water Treatment System to meet the demands of the southern population. This research aims to assess the drinking water quality produced from the AlWajeed Water Treatment System. Monthly water samples were collected (January 2018 to January 2021) from the Al Wajeed Water Treatment Framework (4sites), extending to governorates; Bishah`s distribution system (5sites) and Tathleeth`s distribution system (7sites). Water quality criteria, such as physical, chemical, and microbiological parameters, revealed that the majority of water samples collected from the Al Wajeed Water Framework and its environs are of a good quality matched the national and international standards. Few sites showed water quality criteria, such turbidity, fluoride and total coliform did not comply with national and global standards. The obtained results explained the importance of monitoring and follow-up programs for drinking water criteria. In addition, they can help the authorities and stakeholders in the sustainable development.

In Wikipedia, articles about various topics can be created and edited independently in each language version. Therefore, quality of information about the same topic depends on language. Any interested user can improve an article and that improvement may depend on popularity of the article. The goal of this study is to show what topics are best represented in different language versions of Wikipedia using results of quality assessment for over 39 million articles in 55 languages. In this paper, we also analyze how popular are selected topics among readers and authors in various languages. We used two approaches to assign articles to various topics. First, we selected 27 main multilingual categories and analyzed all their connections with sub-categories based on information extracted from over 10 million categories in 55 language versions. To classify the articles to one of the 27 main categories we took into account over 400 million links from articles to over 10 million categories and over 26 million links between categories. In the second approach we used data from DBpedia and Wikidata. We also showed how the results of the study can be used to build local and global rankings of the Wikipedia content.

In multi-objective optimization problems, the optimization target is to obtain a set of non-dominated solutions. Comparing solution sets is crucial in evaluating the performances of different optimization algorithms. The use of performance indicators is common in comparing those sets and, subsequently, optimization algorithms. A good solution set must be close to the Pareto-optimal front, well-distributed, maximally extended and fully filled. Therefore, an effective performance indicator must encompass these features as a whole and must be Pareto dominance compliant. Unfortunately, some of the known indicators often fail to properly reflect the quality of a solution set or cost a lot to compute. This paper demonstrates that the Degree of Approximation (DOA) quality indicator, is a weakly Pareto compliant unary indicator that gives a good estimation of the match between the approximated front and the Pareto-optimal front. Moreover, DOA computation is easy and fast.

Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. Methods: Fours different processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a mechanical test. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded (figure 4), as well as the breaking energy, Conclusions: The best results were obtained in the case of the thermoplastic injection system and, surprisingly and contrary to those in the specialized literature, the worst results were recorded in the case of 3D printed samples.

Woodland strawberry (Fragaria vesca L.) is an underutilized plant species, appreciated by consumers for its qualitative features. Utilizing technical means of production, such as plant biostimulants, that can increase crop productivity and quality could be highly important in woodland strawberry cultivation. The scope of the present study was to appraise the influence of two biostimulants (Trichoderma atroviride and plant protein hydrolysate) - used either alone or combined - on plant performance and economic profitability of two woodland strawberry genotypes (‘Alpine’ and ‘Regina delle Valli’). Overall, data showed that ‘Alpine’ had the highest productive performances, whereas ‘Regina delle Valli’ revealed the highest fruit qualitative traits. T. atroviride inoculation and V-PH application significantly boosted plant marketable yield (+20.5% for T. atroviride and +12.9% for V-PH), total sugars (+1.9% for Trichoderma and +1.4% for V-PH) and anthocyanins (+14.1% for T. atroviride and +9.8% for V-PH) compared to non-treated plants. Plants supplied with both biostimulants had higher marketable yield (+34.8%), mean fruit weight (+6.0%), fruit dry matter (+13.8%), total sugars (+3.5%), ascorbic acid (+12.7%), flavonoid (+26.3%) and anthocyanins (+29.9%) compared to non-treated plants. Furthermore, our study revealed that the highest fruit polyphenols concentration was recorded in both genotypes treated with the combination of biostimulants and in ‘Regina delle Valli’ sprayed with V-PH, whereas the highest antioxidant activity was found in ‘Regina delle Valli’ fruit when plants were supplied with both biostimulants. Our study pointed out that the application of microbial and non-microbial biostimulants, especially in combination, might be an useful strategy for improving performances of underutilized species and, therefore, encourage its cultivation, valorisation and economic profitability (+10195.3 €/ha when plants were exposed to both biostimulants).

Agriculture is the main economic activity of Mozambique and there is lack of information about the quality of agricultural soils. In this paper, five soils from the Manica and Sussudenga districts (Manica province) were sampled in the years 2021/2022 and 2022/2023 (before and after the rainy seasons), were subjected to an agronomical and environmental chemical analysis to assess its quality, either from the fertility and environmental contamination point of view. Standard analytical methodologies from external certified laboratories and local X-ray fluorescence measurements were used. All the studied soils are acidic (pH ranging from 4.5 and 5.4), have no salinity problems (conductivity ranging from 4.2 to 11.8 mS/m), have low amount of soil organic matter (0.90% to 1.81%), and soils from the Sussudenga district have a very low cation exchange capacity (CEC) (average of 3.33 cmolc/kg), while those from Manica district ranges from very low to average CEC (3.59 to 13.11 cmolc/kg). Also, Sussudenga soils have a phosphorous deficiency (values ranging from &lt;20 to 38.5 mg/kg) and there are deficiencies and/or excesses of some macro and micronutrients in all soil samples. Manica soils are contaminated, apparently from geogenic origin, with Cr (280 to 1400 mg/kg), Co (80 mg/kg), Ni (78 to 680 mg/kg) and V (86 mg/kg). Agricultural soils monitoring must be fostered in Mozambique in order to improve food quality and quantity to assure economic and environmental sustainability.

Sea surface salinity (SSS) is one of the Essential Climate Variables (ECVs) as defined by the Global Climate Observing System (GCOS). Acquiring high-quality SSS datasets with high spatial-temporal resolution is cruicial for research on the hydrological cycle and earth climate. This study assessed the quality of SSS data provided by four high-resolution ocean reanalysis products, including the Hybrid Coordinate Ocean Model (HYCOM) 1/12° global reanalysis, the The Copernicus Global 1/12° Oceanic and Sea Ice GLORYS12 Reanal-ysis, the Simple Ocean Data Assimilation (SODA) reanalysis, the ECMWF Oceanic Reanalysis System 5 (ORAS5) product and the Estimating the Circulation and Climate of the Ocean Phase II (ECCO2) reanalysis. Regional comparison in the Mediterranean Sea shows that reanalysis largely depicts the accurate spatial SSS structure away from river mouths and coastal areas but slightly underestimates the mean SSS values. Better SSS reanalysis performance is found in the Levantine Sea while larger SSS uncertainties are found in the Adriatic Sea and the Aegean Sea. The global comparison with CMEMS level-4 (L4) SSS show generally con-sistent large-scale structures. The mean ΔSSS between monthly gridded reanalysis data and in situ analyzed data is -0.1 PSU in the open seas between 40°S and 40°N with the mean Root Mean Square Deviation (RMSD) generally smaller than 0.3 PSU and the majority of correlation coefficients higher than 0.5. Comparison with collocated buoy salinity shows that reanalysis products well captures the SSS variations at the locations of tropical moored buoy arrays at weekly scale. Among all the four products, the data quality of HYCOM re-analysis SSS is highest in marginal sea, GLORYS12 has the best performance in the global ocean especially in tropical regions. Comparatively, ECCO2 has the overall worst performance to reproduce SSS states and variations by showing the largest discrepancies with CMEMS L4 SSS.

Swimming pools are examples of water-intensive facilities, where solutions for reducing economic and environmental costs are increasingly frequently searched. One of the solutions is the recovery of water from wastewater, including from washings obtained through the process of rinsing filter bed. The study objective was the qualitative and quantitative assessment of post-coagulation sludges, the main pollutant found in the washings. During the analyses, assessment of the sedimentation capabilities of the sludges was performed (gravitationally), particle size distribution was assessed (particle size distribution analyzer) and assessment of phytotoxicity with the use of plant indicators in short-term tests was performed (Lemna minor, Lepidium sativum, Sinapis alba, Raphanus sativus). The samples were collected from two independent circulations, which differed in terms of capacity and type of coagulant used. The tested post-coagulation sludges were characterized by high content of total suspended solids: in samples from Circulation 1 from 251 to 128 mg/l, in Circulation 2 from 489 to 228 mg/l. However, the sedimentation processes enabled significant separation of sludges. The hydrolyzed coagulant contributed to the improvement of sedimentation capabilities of sludges. Despite the fact that in many samples low sludge concentrations favored stimulation of plant growth, the post-coagulation sludges can constitute a hazard to plant growth, particularly in the long-term perspective.

It was once thought that high QoS (Quality of Service) performance solves recurrent problems of low-quality multimedia services. Since then, solutions have been proposed to ensure a high level of QoE (Quality of Experience). In this document, the authors attempt to outline their understanding of an accurate meaning of quality of multimedia services. Starting from QoS and passing through generalised QoE, the authors focus on aspects of subjective and objective quality modelling and optimisation of visual performance for TRV (Target Recognition Video) applications (such as video surveillance), outlining the path of ITU-T standardisation in this area. The authors revised the ITU-T Recommendation P.912 to reflect improved subjective test techniques developed since this Recommendation was approved. The authors also attempt to predict at least some existing errors of reasoning, which are likely to become evident for the industry in the next decade.

The effects of climate change on yield and quality for different climate regions had high uncertainty. Risk assessment is an effective measure to assess the seriousness of the projected impacts for decision-makers. The modified quality model was used to simulate integrated impacts of climate change, environment and management on wheat yield and quality. Then, the Canadian Earth System Model (CanESM2) was used to forecast the daily meteorological data, and Statistical Down Scaling Model was used for downscaling. CERES-Wheat was combined with the forecasted meteorological data to simulate the future wheat yield and grain protein concentration (GPC). The risk of wheat yield and quality in three climatic regions of Shaanxi combined with two climate change scenarios of CanESM2 were assessed. Temperature increased 0.22-3.34 °C and precipitation increased 10-60 mm for RCP4.5 and RCP8.5. Elevated temperature and precipitation had positive effects on yield in all regions. The yield risk of most regions with climate change decreased 3.8%-25.1%. The GPC risk of all regions with climate change decreased 7.3%-27.2%. Irrigation decreased yield risk greatly in all regions, while had totally different effects for the three climatic regions. Yield risk with irrigation decreased 37.7%-52.1% in different climate. In contrast to previous studies, GPC risk with irrigation increased greatly 25.8%-28.9% in humid region, 3.9%-8.8% in sub-humid region, and decreased 37.7%-52.1% in semi-arid region. Climate change decreased yield risk and GPC risk together. While irrigation decreased yield risk greatly in all regions, had totally different effects for the three climatic regions.

A superior variant of dried jujube in China is ‘Huizao’ (HZ) jujube. Nonetheless, detailed evaluations of the texture quality of HZ fruits have been the subject of few studies. Texture is a significant indicator of the sensory and processed quality of a fruit. Here, we differentiate and characterize the texture quality of HZ fruits from the four primary producing regions in southern Xinjiang, as well as develop a system for assessing the texture quality of HZ fruits. Furthermore, five texture indices of HZ fruits from 109 plantations were exhaustively evaluated utilizing principal component analysis, Pearson correlation analysis, and hierarchical clustering analysis. Consequently, by the 10th, 30th, 70th, and 90th percentiles, each index was classified into five grades—lower, medium, high, and higher. Correlation investigation indicated strong relationships between the springiness, chewiness, cohesiveness, gumminess, and hardness of HZ fruits. Springiness, hardness, and adhesiveness are essential indicators that influence the texture of HZ fruits. We used clustering analysis to separate the six texture indices into three major categories (hard factor, stick-elastic factor, and adhesive factor), with indices representing hardness, springiness, and adhesiveness, respectively. Furthermore, according to the factor molecules, the texture quality of HZ fruits in the four production areas was evaluated as Bazhou (1.24) > Hotan (0.773) > Kashi (-0.577) > Aksu (-0.852). RDA analysis of six texture quality parameters and 24 climate conditions identified higher mean temperature (TEM) and lower relative humidity (RHU) as the primary factors contributing to the improved texture quality of HZ fruits in Xinjiang. This study identified the texture quality characteristics of HZ fruits in four major producing areas of Southern Xinjiang, and it offered a theoretical foundation for optimizing the dominant producing areas and regional production of HZ varieties in Xinjiang.

Crowdsourced Data (CSD) generated by citizens is becoming more popular as its potential utilisation in many applications is increasing due to its currency and availability. However, the quality of CSD, including its relevance, is often questioned as the data is not generated by professionals nor follows standard data collection procedures. The quality of CSD can be assessed according to a range of attributes including its relevance. Information relevance has been explored through using in Geographic Information Retrieval (GIR) techniques to identify relevant information. This research tested a relevance assessment approach for CSD by adapting relevance assessment techniques available in the GIR domain. The thematic and geographic relevance were assessed using the Term Frequency-Inverse Document Frequency (TF-IDF), Vector Space Model (VSM) and Natural Language Processing (NLP) techniques. The thematic and geographic specificities of the queries were calculated as 0.44 and 0.67 respectively, which indicates the queries used were more geographically specific than thematically specific. The Spearman's rho value of 0.62 indicated that the final ranked relevance lists showed reasonable agreement with a manually classified list and confirmed the potential of the approach for CSD relevance assessment for other possible crowdsourced data analysis.

Although, promotion of urbanization culture in recent decades has made inevitable development of cities in the world, however, the development can be guided in a direction that leave, to the extent possible, minimum socioeconomic and environmental impacts. For this, it is required to first forecast auto-spreading orientation of cities and suburbs in rural areas over time and then avoid shapeless growth of cities. This paper is an attempt to develop a dynamic hybrid model based on logistic regression (LR), Markov chain (MC), and cellular automata (CA) for prediction of future urban sprawl in fast-growing cities. The model was developed using 12 widely-used urban development criteria, whose significant coefficient was determined by logistic regression, and validated by relative operating characteristic (ROC) analysis. The validated model was run in Guilan, a tourist province in northern Iran with a very high rate of urban development. For this, changes in the area of urban land use were detected over the period of 1989 to 2013 and then, future sprawl of the province was forecasted by the years 2025 and 2037. The analysis results revealed that the area of urban land use was increased by more than 1.7 % from 36012.5 ha in 1989 to 59754.8 ha in 2013, and the area of Caspian Hyrcanian forestland was reduced by 31628 ha. The results also predicted an alarming increase in the rate of urban development in the province by the years 2025 and 2037, during which urban land use is predicted to develop 0.9 % and 1.38 %, respectively. The development pattern is expected to be uneven and scattered, without following any particular direction. The development will occur close to the existing or newly-formed urban basements as well as around major roads and commercial areas. This development, if not controlled, will lead to the loss of 13863 ha of Hyrcanian forests and if the trend continues, 21013 ha of Hyrcanian forests and 20208 ha of Barren/open lands are expected to be destroyed by the year 2037. In general, the proposed model is an efficient tool for the support of urban planning decisions and facilitates the process of sustainable development of cities by providing decision-makers with an overview on future development of cities where the growth rate is very fast.

We previously reported how the loss of CHIP expression (Carboxyl terminus of Hsc70-Interacting Protein) during pressure overload resulted in robust cardiac dysfunction, accompanied by a failure to maintain ATP levels in the face of increased energy demand. In this study, we analyzed the cardiac metabolome after seven days of pressure overload and found an increase in long- and medium-chain fatty acid metabolites in wild-type hearts, a response that was attenuated in mice that lack expression of CHIP (CHIP^-/-). These findings suggest that CHIP may play an essential role in regulating oxidative metabolism, pathways that are regulated in part by the nuclear receptor PPARα (Peroxisome Proliferator-Activated Receptor alpha). Next, we challenged CHIP^-/- mice with the PPARα agonist, fenofibrate. Surprisingly, treating CHIP^-/- mice with fenofibrate for five weeks under non-pressure overload conditions resulted in a loss of skeletal muscle mass and a marked increase in cardiac fibrosis, accompanied by a decrease in cardiac function. Isolated CHIP^-/- cardiac fibroblasts treated with fenofibrate did not increase synthesis of collagen or TGFβ, suggesting that the fibrosis observed in CHIP^-/- hearts likely depends on signaling from other cell types or circulating factors. In conclusion, in the absence of functional CHIP expression, fenofibrate results in unexpected cardiac pathologies. These findings are particularly relevant to patients harboring loss-of-function mutations in CHIP and are consistent with a prominent role for CHIP in regulating cardiac metabolism.

Researchers are exploring solutions to meet the growing demand for protein due to the expected increase in global population by 2050. Interest in alternative protein sources like insects has risen, driven by concerns about environmental impact and the need for sustainable food production. This study aimed to develop and evaluate the physicochemical properties of soy protein-based burger enriched with insect protein from Alphitobius diaperinus. Three formulations were developed: a control (B0), and burgers with 5% (B5) and 10% (B10) insect protein - Whole Buffalo Powder (WBP). Results showed that adding insect protein decreased the burger analogue's pH. There was observed a clear trend of increasing total lipids and SFA, and decreasing MUFA and PUFA, as the WBP concentration increases from 0% to 10%. No significant differences with increasing WBP concentration in the protein content of the burger analogue, as well as the cooking yield, were noted. The WBP addition had a notable effect on the color change, especially decrease in brightness (L*). It was shown that as the WBP concentration increased, there were no significant differences in the texture profile of the burger analogues. The formulation with 5% WBP concentration was the most acceptable in sensory analysis.

The Simultaneous Localization And Mapping (SLAM) scanner is an easy and portable Light Detection And Ranging (LiDAR) data acquisition device. Its main output is a 3D point cloud covering the scanned scene. Regarding the importance of accuracy in the survey domain, this paper aims to assess the accuracy of two SLAM scanners: the NavVis VLX and the BLK2GO Scanner. This assessment is conducted for both outdoor and indoor environments. In this context, two types of reference data are used: the Total Station (TS) and the static scanner Z+F Imager 5016. To carry out the assessment, four comparisons are tested: cloud to cloud, cloud to mesh, mesh to mesh, and edge detection board assessment. However, the results of the assessments confirm that the accuracy of indoor SLAM scanner measurements (5 mm) is greater than that of outdoor ones (between 10 mm and 60 mm). Moreover, the comparison of cloud to cloud provides the best accuracy regarding direct accuracy measurement without manipulations. Finally, based on the high accuracy, scanning speed, flexibility, and the accuracy differences between tested cases, it is confirmed that SLAM scanners are effective tools for data acquisition.

The objective of this study was to assess the ability of producing laminated edible films manufactured using the following proteins; gelatin (G), whey protein isolate (WPI), and polysaccharide; sodium alginate (SA), and to evaluate their physical properties. Additionally, films’ preparation employing these ingredients was optimized through the addition of corn oil (O), Overall, 8-types of laminated films (G-SA, G-WPI, SA-WPI, SA-G-WPI, GO-SAO, GO-WPIO, SAO-WPIO, SAO-GO-WPIO were developed in this study. The properties of the prepared films were characterized through the measurement of; tensile strength (TS), elongation at break point (EB), puncture resistance (PR), tear strength (TT), water vapour permeability (WVP) and oxygen permeability (OP). The microstructure of cross-sections of laminated films was investigated by scanning electron microscopy (SEM). Mechanical properties of films were dramatically enhanced through the addition of film layers. GO-SAO laminate showed the best barrier properties to water vapour (22.6 ± 4.04 g mm/kPa d m2) and oxygen (18.2 ± 8.70 cm3 mm/kPa d m2). SAO-GO-WPIO laminate film was the strongest of all laminated films tested, having the highest TS of 55.77 MPa, PR of 41.36 N and TT of 27.32 N. SA-G-WPI film possessed the highest elasticity with an EB value of 17.4%.

When the image quality is evaluated, the human visual system (HVS) infers the details in the image through its internal generative mechanism. In this process, the HVS integrates both local and global information of the image, utilizes contextual information to restore the original image information, and compares it with the distorted image information for image quality evaluation. Inspired by this mechanism, a no-reference image quality assessment method is proposed based on a multitask image restoration network. The multitask image restoration network generates a pseudo-reference image as the main task and produces structural similarity index measure map as an auxiliary task. By mutually promoting the two tasks, a higher quality pseudo-reference image is generated. In addition, when predicting the image quality score, both the quality restoration features and the difference features between the distorted and reference images are used, thereby fully utilizing the information from the pseudo-reference image. To enable the model to focus on both global and local features, a multi-scale feature fusion module is proposed. Experimental results demonstrate that the proposed method achieves excellent performance on both synthetically and authentically distorted databases.

Water is an essential commodity to sustain life. The condition of water in Tiruchirappalli was measured using different Physicochemical parameters like Temperature, pH, TDS, Total Solids, Salinity, Total Hardness, and Electrical Conductivity. Water samples were collected from different places in Tiruchirappalli city, Tamil Nadu. Water samples were examined by different chemical methods. According to the results, Thiruvarambur-1 showed comparatively higher results in the case of every parameter compared to other sampling stations. Obtained results were further interpreted using statistical tools. Considering ECs as a principal component for the regression and correlation analysis with other parameters significant correlation was found. A strong correlation was observed between ECs and TDS, Total Hardness, Turbidity, and Salinity.

Since people spend most of their time in indoor environments, the objective of this work was to study indoor air quality perception and its effects on users’ thermal comfort. Based on previous data from a building with a central air-conditioning system and two mixed-mode buildings located in the humid subtropical climate of Florianópolis, southern Brazil, statistical analyses were performed. Each user subjective answer obtained through a questionnaire was combined with the corresponding environmental conditions – measured using microclimate stations, a portable thermo-anemometer and a CO2 analyser. Results showed that improvement in air quality was associated with the reduction of air temperature and humidity ratio. Also, there was a significant influence of thermal, air movement and humidity sensation and acceptability of air quality perception. Users felt more satisfied or neutral with air quality for being in thermal comfort, and not because of the CO2 level – which means that air quality perception is influenced by factors other than CO2. This study recommends the implementation of an air exchange device in split air-conditioners with air recirculation used in mixed-mode buildings in Brazil. It is important to provide suitable indoor ventilation to reduce pollutants concentration, ensure good air quality and prevent respiratory diseases.

Summary Genome assembly projects have grown exponentially due to breakthroughs in sequencing technologies and assembly algorithms. Evaluating the quality of genome assemblies is critical to ensure the reliability of downstream analysis and interpretation. To fulfil this task, we have developed the AssemblyQC pipeline that performs file-format validation, contaminant checking, contiguity measurement, gene- and repeat-space completeness quantification, telomere inspection, taxonomic assignment, synteny alignment, scaffold examination through Hi-C contact-map visualisation, and assessments of completeness, consensus quality and phasing through K-mer analysis. It produces a comprehensive HTML report with method descriptions, tables, and visualisations. Availability and Implementation The pipeline uses NextFlow for workflow orchestration and adheres to the best-practice established by the nf-core community. This pipeline offers a reproducible, scalable, and portable method to assess the quality of genome assemblies – the code is available online.GitHub: https://github.com/Plant-Food-Research-Open/assemblyqc Supplementary information Pipeline usage documentation, parameter descriptions and example outputs are available on GitHub: https://github.com/Plant-Food-Research-Open/assemblyqc/tree/main/docs. A preview report is also hosted online: https://plant-food-research-open.github.io/assemblyqc

The digital transformation in Industry 4.0 has revolutionized quality control paradigms, integrating advanced technologies such as augmented reality, deep learning, and computer vision systems into a new era called "Quality 4.0". This study systematically reviews how these technologies are shaping new practices in continuous quality supervision and improvement, adapting to increasingly automated and connected production environments. Through a comprehensive analysis of the literature, practical applications in various industrial sectors, from manufacturing and agriculture to the production of sweets and snacks, are highlighted. Additionally, the conceptual and detailed design of a quality control system using artificial intelligence tools is presented, focusing on the inspection of dimensions, color, weight, and labeling of MDF boxes. The proposed system demonstrates an effective integration of sensors, high-definition cameras, and deep learning algorithms, validated through tests with boxes of different sizes. The results suggest that the adoption of these technologies not only improves the accuracy and efficiency of inspections but is also essential to maintaining high-quality standards in a dynamic and competitive industrial environment.

Anthropogenic development can strongly influence natural river processes, leading to environmental changes that negatively affect important habitats and biodiversity, and consequently reduce economically important natural resources. This study investigated the effects of salinity intrusion on the habitat of the clam Corbicula japonica in the Seomjin River estuarine zone. We employed the Environmental Fluid Dynamics Code (EFDC) model, which incorporates topographic data and hydrological changes, to simulate salinity concentrations. Two salinity measurement facilities were installed in Seomjin River estuarine and operated to optimize the EFDC model. The results show that reduced flow rates due to intake have a negligible impact on the increased salinity. Maintaining optimal salinity (15–20 psu) during neap tides at the Seomjin River Bridge requires constant high flow rates, which poses significant challenges. Saltwater stratification is identified as the primary cause of pronounced salinity stratification, particularly during neap tides. Addressing this issue through river discharge and intake facility operation is challenging. Structural measures, including riverbed restoration and underwater barriers, are recommended to improve resistance to seawater intrusion. Future research should aim to develop scenarios to reduce salinity concentrations, quantify the reduction efficiency, and propose region-specific measures.

This study used Dutch potatoes at the end of dormancy as the material to explore the impact of menthol (0.2 and 0.5 g/kg based on potato mass) treatment on sprouting inhibition and potato quality. The findings revealed that a menthol concentration of 0.5 g/kg effectively inhibited potato tuber sprouting and significantly reduced glucoside alkaloids production. After a storage period of 15 days, the sprouting percentage and glucoside alkaloids content of potatoes treated with 0.5 g/kg menthol were observed to be significantly lower at 4.17% and 68.63 mg/kg, respectively, compared to the control group which exhibited values of 100% and 282.01 mg/kg, respectively (P < 0.05). Throughout the storage period, 0.5 g/kg of menthol promoted respiration, reduced malondialdehyde production in potatoes, inhibited polyphenol oxidase activity, and slowed down tissue browning. Additionally, it mitigated the decline in starch and soluble protein content, inhibiting the accumulation of reducing sugars.

ITRF input data which are integrated by GNSS, SLR, VLBI, DORIS combination centers are considered to be relatively high-quality and accurate solutions. However, when utilizing these inputs, one still needs to identify outliers, rescale inaccurate covariance matrix and evaluate the precision of the observed datum information. To achieve the above-mentioned objectives, we propose a terrestrial reference frame (TRF) stacking approach to establish the single technical reference frameworks for the ITRF2014 and ITRF2020 datasets of all four technologies. As a result, roughly 0.5% or less of the SLR observations are identified as outliers, while the ratio of DORIS, GNSS, and VLBI observations are below 1%, around 2%, and ranging from 1% to 1.2%, respectively. The post-rescaling covariance scale factors are 25.07, 27.25, 18.84, 6.98 for GNSS, SLR, VLBI, and DORIS in ITRF2014 datasets, and 8.95, 14.9, 16.8, 7.78 in ITRF2020 datasets, respectively. It is shown that the consistency between the SLR scale and ITRF has improved, increasing from around -5mm in ITRF2014 datasets to approximately -1mm in ITRF2020 datasets. The scale velocity derived from fitting the VLBI scale parameter series with all epochs in ITRF2020 datasets differs by approximately 0.21mm/year from the velocity obtained by fitting the data up to 2013.75 because of the scale drift of VLBI at around 2013. The decreasing standard deviations of the Polar motion parameter (XPO, YPO) offsets between Stacking TRFs and 14C04 (20C04) indicating an improvement in the precision of polar motion observations for all of the four techniques. From the perspective of the Weighted Root Mean Square in station coordinates, the measurement precision of GNSS, SLR, and DORIS techniques has improved, while VLBI shows no significant change.

With proper processing and utilization, biofortified cassava may contribute to the nutritional status of the consumers, thus, the need for this study. High-quality cassava flour from white- (TME 419) and biofortified (TMS 01/1368) cassava varieties were produced at a commercial processing factory, after which the flour is composite with wheat flour to produce bread. The nutritional composition, physical properties and sensory quality of the composite bread were analyzed using standard methods. Results showed that composite bread from 20% biofortified cassava flour (20-YCF) had a higher value of total β-carotene (0.74 μg/g), moisture (37.83%) and ash (2.29%) contents. The fat (3.72%) and protein (12.83%) contents were higher in 20% white cassava flour (20-WCF) composite bread. The 20-YCF composite bread had the highest loaf volume (3286.2 cm3), elasticity (6.32), chewiness (40.51 N) and gumminess (6.41), 20-WCF composite bread had higher specific volume (3.59 cm3/g) and hardness (176.50 N). The 100% wheat bread had higher cohesiveness (0.10) and loaf weight (932.35 g). A significant negative correlation (r = - 0.98, p≤0.05) exist between bread hardness and protein content. The composite bread compared favourably with the 100% wheat bread in terms of weight and aroma, but, the 100% wheat bread was more acceptable.

Atlantic salmon (Salmo Salar) is one of the fish species that rich in omega-3 fatty acids. Consumption of omega-3 fatty acids can lower down the risk of cardiovascular disease and coronary heart disease. The extraction of omega-3 fish oil from Atlantic salmon by using hexane and isopropanol was conducted in this research. Response Surface Methodology (RSM) was used to study the impact of parameters which were temperature (50-90°C), centrifuge speed (1000-3000rpm) and solvent ratio of hexane to isopropanol (0.5-1.5) to the percentage of oil yield. The results obtained shows that 15.23%± 0.61 of oil yield from Atlantic salmon under an optimum condition of 70°C, 3000 rpm and solvent ratio of hexane to isopropanol of 1.5. The acid value, peroxide value and p-anisidine value of the fish oil obtained were 7.48 mg KOH/g, 1.94 meq/kg and 5.56 respectively which were all within the acceptable limit which stipulated by Global Organization for EPA and DHA (GOED) and Food and Agricultural Organization of the United Nations (FAO). The FTIR analysis proved the presence of alkane and carboxylic acid in the fish oil. Furthermore, GC-MS analysis showed that the fish oil contains higher monounsaturated fatty acids (MUFA) contents followed by polyunsaturated fatty acids (PUFA) and 4.5525% of total omega-3 fatty acids.

This work aimed to develop an easy-to-use smartphone-based electrochemical biosensor to quickly assess coffee blend's total polyphenol (Phs) content at industrial and individual level. The device is based on a commercial carbon-based screen-printed electrode (SPE) modified with multi-walled carbon nanotubes (CNTs) and gold nanoparticles (GNPs). At the same time, the biotransducer, Laccase from Trametes versicolor, TvLac, was immobilized on the sensor surface by using glutaraldehyde (GA) as cross-linking agent. The platform was electrochemically characterized to ascertain the influence of the SPE surface modification on its performance. The working electrode (WE) surface morphology characterization was obtained by scanning electron microscopy (SEM) and Fourier-transform infrared (FT-IR) imaging. All the measurements were carried out with a micro-potentiostat Sensit Smart by PalmSens connected to a smartphone. The developed biosensor provided a sensitivity of 0.12 μA/μM, a linear response ranging from 5 to 70 μM, and a lower detection limit (LOD) of 2.99 μM. Afterwards, the biosensor was tested for quantifying the total Phs content in coffee blends, evaluating the influence of both the variety and the roasting degree. The smartphone-based electrochemical biosensor performance has been validated though the Folin-Ciocâlteu standard method.

To date, most people prefer softer and stickier rice with high glycaemic index, which has led to the study of the association between the dietary fibre profile and the textural properties to balance between the eating quality, and health benefits. A slight variation was observed in the dietary fibre composition among rice varieties with different amylose content. The percentage of insoluble dietary fibre (IDF) in whole grain rice varied from 1.65–4.32 while the percentage of soluble dietary fibre (SDF) ranged from 0.26–1.37. We demonstrated that the SDF/IDF ratio was higher in soft texture rice with low amylose and it shared a negative correlation with hardness and chewiness of cooked whole grain rice determined by a texture analyser, which suggested that the distribution of SDF throughout the rice endosperm influences the reduction of the hardness of cooked rice. According to the importance of dietary fibre, we proposed a simple linear regression method to estimate the amount of IDF and total dietary fibre with r = 0.97 and 0.92, respectively, of whole grain rice based on its bran layer, determined by the alternative alkaline method. Furthermore, low amylose rice has higher content of -glucan and pectin, which are classified as soluble dietary fibre, than high amylose rice. The percentage of -glucan and pectin in whole grain rice ranged from 0.03 and 0.07 respectively, for high amylose rice to 0.14 and 0.27 respectively for low amylose rice,

Superior fiber quality is one of the most important objectives in cotton breeding. To detect the genetic basis underlying fiber quality, an F2 population containing 413 plants was constructed by crossing Jifeng 914 and Jifeng 173, both of which have superior fiber quality, with Jifeng 173 being better. Five fiber quality traits were investigated in the F2, F2:3, F2:4, and F2:5 populations. Quantitative trait loci (QTL) mapping was conducted based on a high-density genetic map containing 11,488 single nucleotide polymorphisms (SNPs) and spanning 4,202.12 cM in length. Transgressive segregation patterns and complex correlations in the five tested traits were observed. A total of 108 QTLs were found, including 27 for fiber length (FL), 16 for fiber strength (FS), 24 for micronaire (MC), 17 for fiber uniformity (FU), and 24 for fiber elongation rate (FE). Chromosome A7 contained 12 QTL, ranking the first. No QTL was found on chromosome D1 and D11. Each QTL contributed 1.98%–21.45% to the phenotypic variation (PV), including 13 major effect QTLs that contributed more than 10% toward PV. Two QTLs could be repeatedly detected in three populations, including qFL-D3-2 in F2, F2:4, and F2:5 with 9.18%–21.45% of PV, qFS-A11-1 in F2:3, F2:4 and F2:5 with 6.05%–10.41% of PV. Another seven stable QTLs could be detected in two populations, including four major effect QTLs: qFL-A12-3, qFS-D10-2, qMC-D6-2, and qMC-D8-1. Fourteen QTL-overlapping regions were found, which might explain the complex correlations among the five phenotypic traits. Four regions on chromosome A11, D3, D6, and D10 covered by both stable and major effect QTLs are promising for further fine mapping. The genomic regions of the two QTLs detected in three populations and the four major effect QTLs contain 810 genes. Gene functional analysis revealed that the annotated genes are mainly involved in protein binding and metabolic pathways. Fifteen candidate genes in the qFL-D3-2 region are highly expressed in fiber or ovules during fiber initiation, elongation, secondary cell wall thickening, or maturation stages. qRT-PCR revealed that Ghir_D03G005440.1 and Ghir_D03G011310.1 may play a role in promoting fiber initiation, Ghir_D03G006470.1 may be beneficial for promoting fiber elongation. This study provides more information for revealing the molecular genetic basis underlying cotton fiber quality.

As the most serious of the many worse new pathological changes caused by diabetes, there are many risk factors for the occurrence and development of DR. It mainly includes hyperglycemia, hypertension, hyperlipidemia and so on. Among them, hyperglycemia is the most critical cause, which plays a key role in the pathological changes of DR.High-sucrose diets(HSDs) lead to elevated blood glucose levels in vivo, which, through oxidative stress, inflammation, the production of AGEs and VEGF, causes plenty of pathological damages to the retina and ultimately bring about loss of vision. The existing therapies for DR primarily target the terminal stage of the disease, when irreversible visual impairment has appeared. Therefore, early prevention is particularly critical. Early prevention of DR-related vision loss requires adjustments to dietary habits, mainly by reducing sugar intake. This article primarily discusses the risk factors, pathophysiological processes, and molecular mechanisms associated with the development of DR caused by HSDs. It aims to raise awareness of the crucial role of diet in the occurrence and progression of DR, promote timely changes in dietary habits, prevent vision loss, and improve the quality of life. The aim is to make people aware of the importance of diet in the occurrence and progression of DR. According to the dietary modification strategies we give, patients can change their poor eating habits timely, avoid the retinopathy that can be avoided theoretically, and obtain a excellent outcome.

The p53 tumor suppressor protein shows antiviral activity. The replication of viruses is also antagonized by interferons (IFNs) – cytokines, which control immunity genes by the STAT transcription factors. The best studied interferons belong to type I (e.g. IFNα) and type II (IFNγ) groups. IFNα and IFNγ both induce activating phosphorylation of STAT1 on Tyr701. Previously, we noticed that p53 activates SOCS1, which is a negative regulator of STAT1 phosphorylation. Thus, we hypothesized that p53 by activating SOCS1 expression reduces phosphorylation of STAT1 and attenuates activation of genes stimulated either by IFNα or IFNγ. To test this hypothesis, we exposed p53-proficient and p53-deficient cells to strong p53 activators, and either to IFNα or IFNγ. Subsequently, we estimated the phosphorylation status of STAT1 and the expression of genes regulated by either of these cytokines. Strong activation of p53 reduced the phosphorylation of STAT1 on Tyr701, however surprisingly it did not lead to reduced expression of most tested interferon-stimulated genes. On contrary, p53 and IFNγ synergized in the activation of CASP1, IFIT1 and IFIT3 genes. We conclude that the interactions between p53 and interferon-activated pathways are more complicated than initially expected, but the apparent cooperation between p53 and IFNγ deserves further studies.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

Abstract: In Australia adoption of reduced tillage and stubble retention cropping systems to conserve soil moisture by growers has seen an increase in the prevalence of the disease Fusarium crown rot (FCR) caused by the stubble-borne fungal pathogen Fusarium pseudograminearum. Durum wheat is particularly susceptible to FCR expressing significant yield and quality losses in the presence of infection. Increasing rates of nitrogen (N) application at sowing exacerbates FCR. However, to achieve the desired grain protein and quality suited to pasta manufacture, N application is necessary and this creates a dilemma for growers. The purpose of this study was to investigate the effects of FCR infection in the presence of different N fertiliser application rates in durum wheat varieties on yield and technological quality. Two durum varieties were evaluated at the same location over two seasons (2020 and 2021). These seasons were characterised by being wetter than normal and showed different responses to FCR and N application. In general, the 2021 season showed better responses to applied N with no impact of FCR. The FCR inoculation while it resulted in significant infection, it had no impacts on yield or grain quality in 2021 while in 2020 yield was reduced and only gluten index was reduced. Jandaroi was found to hold its kernel vitreosity at all protein levels obtaining the premium grade while DBA Lillaroi did not and would suffer downgrade if N application was insufficient. However, higher N application rates needed to achieve 12% + protein saw a reduction in dough strength with Jandaroi holding its dough strength much better than DBA Lillaroi. This was related to the lower glutenin/gliadin (Gli/Glu) ratio in response to applied N at sowing in Jandaroi which helped retain kernels with high vitreousness. This suggests genetics plays an important role in a genotype response to N fertilisation and should be considered when selecting a variety where higher premium grades are desirable.

The aim of this study was to research the quality parameters of honeys directly from Iraqi Kurdistan beekeepers and to compare with European Union law and Central European honeys. In total 30 honey samples directly from Kurdish, Czech and Slovak beekeepers were collected from the year of production 2018. The analyzed physicochemical parameters and bioactive compounds (moisture content, electrical conductivity, diastase activity, hydroxymethylfurfural content, pH, free acidity, total phenolic content, color, color intensity) varied depending on the botanical and geographical origin of honeys. Comparing Kurdistan honeys with a directive relating to honey, only two honey samples had diastase activity lower than limit and one sample had free acidity value at the legislative limit. Based on the results, it was found that the properties of Kurdistan honeys were very similar to the properties of Czech and Slovak honeys, as indicated by the detected statistically non-significant differences (p > 0.05) between the moisture content, electrical conductivity, diastase activity and color. On the contrary, the most significant differences (p < 0.01) were detected in hydroxymethylfurfural content, total phenolic content, and color intensity. Our results indicated the specific properties and the uniqueness of honeys from Iraqi Kurdistan and pointed to the possibility of trading this honey in Europe.

The emergence of the coronavirus 19 (COVID-19) has posed a major challenge to healthcare systems worldwide, especially as COVID-19 mutations complicate the development of vaccines and antiviral drugs. Therefore, the search for natural products with broad anti-COVID-19 capabilities is an important option for the prevention and treatment of infectious diseases. Lectins, which are widely recognized as antiviral agents, could contribute to the development of anti-COVID-19 drugs. In this study, we evaluated the binding ability of a total of six lectins, including MVL from Microcystis viridis NIES-102, to the spike protein RBD of the original (wild) COVID-19 and it’s three mutants: alpha, delta, and omicron. As a result, two lectins, MVL from Microcystis viridis NIES-102 and jacalin from Artocarpus altilis, showed distinct binding ability to the RBDs of the four COVID-19 strains. The other lectins (DB1, ConA, PHA-M and CSL3) did not show any binding ability. Although the glycan specificities of the two lectins, MVL and Jacalin, were different, they showed the same affinity for the RBDs of the four COVID-19 strains, i.e., alpha &gt; delta &gt; original &gt; omicron. The verification of glycan-specific inhibition revealed that jacalin binds to RBDs by glycan-specific recognition, whereas MVL binds to RBDs by protein-protein interactions in addition to glycan-specific recognition.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.