A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

The conformity assessment of products or a measured value with the given standards is carried out based on the global risk of producers and consumers calculation. A product may conform to specifications but be falsely rejected as non-conforming. This is about the producer's risk. If a product doesn't meet the requirements but is falsely accepted as conforming, that poses a risk to the consumer. The conventional approach to risk assessment, which yields only a single numerical value for the global risk of producers and consumers, is naturally extended, and utilized for assessing risk in measurement models with linear regression. The outcomes of the two-dimensional extension, along a moderate scale, are the parabolas with an opening upwards. Risk surfaces were obtained through three-dimensional extension over the area limited by the moderate scale and guard band axes. Four models with different ranges of tolerance intervals were used to test this innovative method of risk assessment in linear regression. The corresponding standard measurement uncertainties are determined by applying a simplified measurement model with the use of comprehensive data on the measurement performance and by determining measurement uncertainty derived from consideration of the functional relationship obtained by linear regression analysis. Models that utilize information from linear regression analysis to determine measurement uncertainty are biased towards risks at the edges of the moderate scale. Testing the model's performances with metrics related to the confusion matrix, such as the F1 score, further substantiated this assertion. The diagnostic odds ratio has been proven to be extremely effective in identifying the curve along the guard band axis, along which the global risks of producers and consumers are at their lowest.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Two new dimacrolide sesquiterpene pyridine alkaloids (DMSPAs), dimacroregelines A (1) and B (2), were isolated from the stems of Tripterygium regelii. The structures of both compounds were characterized by extensive 1D and 2D NMR spectroscopic analyses, as well as HRESIMS data. Compounds 1 and 2 are two rare DMSPAs possessing unique 2-(3′-carboxybutyl)-3-furanoic acid units forming the second macrocyclic ring, representing the first example of DMSPAs bearing an extra furan ring in their second macrocyclic ring system. Compound 2 showed inhibitory effects on the proliferation of human rheumatoid arthritis synovial fibroblast cell (MH7A) at a concentration of 20 μM.

The ongoing challenge to ensure a sustainable and affordable energy supply forces industrial companies to implement appropriate measures. These measures typically lead to an increased system complexity, which has to be addressed during operation. Whereas existing approaches from the field of supervisory and optimal control appear to be capable of mastering this issue, these are still not adopted in industry. Therefore, this work presents a procedure model for the systematic development of application-oriented operating strategies for industrial energy supply systems. The procedure model combines research approaches from the fields of sequencing control and approximate MPC to extract rule-based operating strategies. By splitting the procedure model into five phases, expert knowledge can be integrated in a target-oriented manner. Subsequently to the description, the procedure model is exemplary applied to the example of an industrial heating supply system. Throughout an optimization study, the developed operating strategy is compared to a MPC strategy as well as a baseline strategy. Whereas the conventional MPC approach is the upper bound with regard to optimality, the developed operating strategy is able to generate comparable results. Compared to the baseline strategy, a relative reduction in operating expenses of 5.4 % to 37.0 % are achieved in this specific use case.

Background/Objectives: PEMF therapy has gained significant attention due to its potential benefits in promoting tissue repair and improving overall well-being. Recent publications in the field of exercise physiology, showed that pulsed electromagnetic fields (PEMFs) enhanced the velocity and the quantity of muscle O2 available and the rate of muscle oxygen extraction and utilization, in semi-professional cyclists, during a heavy constant-load exercise. In this paper, we investigate the effect of stimulation on muscular activation, in sedentary young people, during a constant-load exercise, performed at moderate intensity. Methods: Nine male sedentary young people, partic-ipated in this study. The response of the muscle activity, was recorded by surface EMG and assessed measuring the root mean square (RMS) normalized to the peak of the maximum voluntary con-traction. Data were collected in the right vastus Medialis (RVM) and right Biceps Femoris (RBF) at the baseline (standstill sitting), on warm-up (unloaded cycling) and during 30 minutes of con-stant-load exercise, in two experimental conditions (PEMF ON vs PEMF OFF). Results: The mul-tivariate analysis of variance performed on RVM showed a significant effect of PEMF in both warmup and exercise, while on RBF showed a significant effect of PEMF and warmup. Conclusions: PEMF strongly enhanced the amplitude of muscle activity in young sedentary people. The increase in the amplitude of the muscular response may lead to a higher oxygen consumption and release.

Induction heating is a fast, reproducible, and efficient heating method used in various manufacturing processes. However, there is no established additive manufacturing (AM) process based on induction heating using wire as feedstock. This study investigates a novel approach to AM based on inductive heating, where a steel wire is melted and droplets are detached periodically using a two-winding induction coil. The process parameters and energy input into the droplets are characterized. The induction generator exhibits sluggish response to the excitation voltage, resulting in a lag in the coil current. The process is captured using a high-speed camera, revealing regular droplet formation and uniform size and shape when operated within an appropriate process window. Larger drops and increased spatter formation occur outside this window. The proposed method allows for the production of droplets with almost spherical shapes. Further analysis and characterization of droplet formation and energy input provide insights into process optimization and overall efficiency.

Bacteriophages (phages) are potential alternatives to chemical antimicrobials against pathogens of public health significance. Understanding the diversity and host specificity of phages is important for developing effective phage biocontrol approaches. Here, we assessed the host range, morphology, and genetic diversity of eight Salmonella enterica phages isolated from a wastewater treatment plant. The host range analysis revealed that six out of eight phages lysed more than 81% of the 43 Salmonella enterica isolates tested. The genomic sequences of all phages were determined. Whole genome sequencing data (WGS) data revealed that phage genome sizes ranged from 41 to 114 kb with GC contents be-tween 39.9 and 50.0 %. Two of the phages SB13 and SB28 represent new species Epsep-timavirus SB13 and genera Macdonaldcampvirus, respectively as designated by the In-ternational Committee for the Taxonomy of Viruses (ICTV) as per genome based taxonomic classification. One phage (SB18) belonged to the Myoviridae morphotype while the re-maining phages belonged to the Siphoviridae morphotype. The gene content analyses showed that none of the phages possessed virulence, toxin, antibiotic resistance, type I-VI toxin-antitoxin modules or lysogeny genes. Three (SB3, SB15 and SB18) out of the eight phages possessed tailspike proteins. Whole genome-based phylogeny of the eight phages with their 113 homologs revealed three clusters A, B, C and seven subclusters (A1, A2, A3, B1, B2, C1 and C2). While cluster C1 phages were predominantly isolated from animal sources, cluster B contained phages from both wastewater and animal sources. The broad host range of these phages highlights their potential use to control the presence of S. enterica in foods.

Properties of time domain parameters of the vibration signal have been extensively studied for the fault diagnosis of rolling element bearings (REB). Parameters like kurtosis and Envelope Harmonic-to-Noise Ratio are most widely applied in this field and some important progress has been made. However, since only one-sided information is contained in these parameters respectively, problems still exist in practice when the signals collected are of complicated structure and/or contaminated by strong background noises. A new parameter, named Shock pulse index (SPI), is proposed in this paper. It integrates the mutual advantage of both parameters above and can help effectively identify fault related impulse components under the interference of strong background noises, unrelated harmonic components and random impulses. The SPI optimizes the parameters of Maximum Correlated Kurtosis Deconvolution (MCKD), which is used to filter the signals under consideration. Finally, the interested transient information contained in the filtered signal can be highlighted through demodulation with Teager Energy Operator (TEO). Fault related impulse components can therefore be extracted accurately. Simulations and experiment analyses verify the effectiveness and correctness of the SPI.

In this paper we describe a method which combines sentiment analysis with machine learning techniques and/or multivariate statistical analysis. By applying this methodology it is possible to classify a collection of texts into two or more groups or clusters. On the basis of a number of previously defined clusters, the novelty of the outlined approach is the use of the sentiment analysis results as input to the machine learning model or multivariate statistical analysis. Once the classifier has been obtained, we can assign a given text into one of the pre-established clusters. The groups or clusters can represent different time periods, classes of texts transcribed from different conversations, etc. The method is illustrated through an example taken from one of the two studies in which we have applied this methodology. In one of the studies, the method was used to classify press news of a volcanic eruption, while in the other study it was used to classify the conversations recorded between a chatbot with different kinds of speakers (humans or chatbots). This last study was the seminal work in which we introduced this methodology.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

Pardosa pseudoannulata is one of the most common wandering spiders in agricultural fields and a potentially good bioindicator for heavy metal contamination. However, little is known about the mechanism by which spiders respond to heavy metals at the molecular level. In this study, high-throughput transcriptome sequencing was employed to characterize the de novo transcriptome of the spiders and to identify differentially expressed genes (DEGs) after cadmium exposure. We obtained 60,489 assembled unigenes, 18,773 of which were annotated in the public databases. Ultimately, 3450 cDNA simple sequence repeats were identified and validated as potential molecular markers in the unigenes. A total of 2939, 2491 and 3759 DEGs were detected among the three libraries of two Cd-treated groups and the control. Functional enrichment analysis revealed that metabolism processes and digestive system function were predominately enriched in response to Cd stress. At the cellular and molecular levels, significantly enriched pathways in lysosomes and phagosomes as well as replication, recombination and repair demonstrated that oxidative damage resulted from Cd exposure. Based on the selected DEGs, certain critical genes involved in defence and detoxification were analysed. These results may elucidate the molecular mechanism underlying spiders' responses to heavy metal stress.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

Grain quality, cooking quality and nutritional quality traits are some of the major attributes that enhance uptake and utilisation of improved cowpea varieties. Therefore, there is need for a better understanding of the genetic variation and inter-relationships among these quality traits in cowpea to integrate them in cowpea breeding programs. The study was conducted to determine genetic variability among 306 cowpea genotypes for grain quality, cooking quality and nutritional quality traits and to understand the interrelationships among these traits for exploitation in breeding programs. The results showed highly significant differences (P

The dynamic behaviour of a machine tool (MT) directly influences the machining performances. The adoption of lightweight structures may reduce the effects of undesired vibrations and increasing the workpiece quality. This paper aims to present and compare a set of hybrid materials that may be excellent candidate to fabricate the MT moving parts. The selected materials have high dynamic characteristics and capacity to damp mechanical vibrations. In this way, starting by the kinematic model of a milling machine that highlights the main critical factors, this study paper evaluates a number of prototypes made of Al Foam sandwiches (AFS), Al Corrugated sandwiches (ACS) and materials reinforced by carbon fibres (CFRP). A set of prototypes has been fabricated, represented the Z-axis ram of a commercial milling machine. The static and dynamical properties have been evaluated by using both FE simulations and experimental tests. The obtained results show that the proposed structures may be a valid alternative to the conventional materials of MT moving parts, increasing machining performances. In particular, the AFS prototype highlighted a damping coefficient that is 20 times greater than a conventional ram (e.g. steel). The CFRP structure is able to satisfy the machining requirements with a reduced weight of 48.5%, while the ACS prototype showed a good trade-off between stiffness and damping.

In multi-objective optimization problems, the optimization target is to obtain a set of non-dominated solutions. Comparing solution sets is crucial in evaluating the performances of different optimization algorithms. The use of performance indicators is common in comparing those sets and, subsequently, optimization algorithms. A good solution set must be close to the Pareto-optimal front, well-distributed, maximally extended and fully filled. Therefore, an effective performance indicator must encompass these features as a whole and must be Pareto dominance compliant. Unfortunately, some of the known indicators often fail to properly reflect the quality of a solution set or cost a lot to compute. This paper demonstrates that the Degree of Approximation (DOA) quality indicator, is a weakly Pareto compliant unary indicator that gives a good estimation of the match between the approximated front and the Pareto-optimal front. Moreover, DOA computation is easy and fast.

MzSTools is a plugin for QGIS developed by the Institute of Environmental Geology and Geoengineering of the National Research Council (CNR-IGAG). The plugin has been designed as a set of practical and easy-to-use tools to carry out seismic microzonation (SM) studies, by producing standard compliant geographic database and maps, thus making them accurate, homogeneous and uniform for all municipalities in Italy. A geodatabase based on SQLite/SpatiaLite Relational Database Management System (RDBMS) has been designed to collect and store data related to elements such as: geognostic surveys; bedrocks and cover terrains; superficial and buried geomorphological elements; tectonic-structural elements; elements of geological instability such as landslide zones, liquefaction zones and zones affected by active and capable faults; homogeneous microzones in seismic perspective, microzones characterized by a seismic amplification factor. MzSTools assembles in a single software environment a set of useful tools in a configurable QGIS project template, comprising layers, symbol libraries, cartographic styles and print layouts for the SM maps. The plugin is open source and hosted on the GitHub platform, and available via the official QGIS plugins repository (https://plugins.qgis.org/plugins/MzSTools/).

Predictive numerical models in the study of ground-borne vibrations generated by railway sys-tems have traditionally relied on the segmented approach of subsystems. In this approach, loads are individually applied, and the cumulative effect of rolling stock is obtained through superposi-tion. While this method serves to mitigate computational costs, it may not fully capture the com-plex interactions involved in ground-borne vibrations. Recent advancements in computational and software tools have enabled the development of more sophisticated vibrational pollution models. These advanced models encompass the entire dynamic system, from the rolling stock to the terrain, allowing for continuous simulations with a defined time step. Furthermore, the incorporation of computational contact tools between various ele-ments not only ensures temporal accuracy but also extends the analysis to the frequency domain. This paper explores the evolution of predictive numerical models in the context of ground-borne vibrations generated by trains on ballasted tracks. It highlights the shift from segmented models to continuous simulations, demonstrating the progressive advancement towards more comprehen-sive and accurate representations of railway-induced and generated vibrations in the track sur-roundings as an additional way of evaluate sustainability of infrastructures. In particular, this development of a numerical model from its inception aimed to expand upon ex-isting emission - prediction models by enriching the data with frequency-domain information. This approach has been driven by the aspiration to bridge the gap between numerical predictions and measured signals, striving for a higher level of accuracy in our obtained results. This model can predict the impact of a high-speed rail (HSR) vehicle passing on its own track. It possesses sufficient information in both the time and frequency domains to precisely characterize vibrations. This initiative marks a pivotal advancement, enabling us to more effectively capture the intricacies of ground-borne vibrations and their impact on the surrounding environment due to a deeper comprehension of the occurrences in the frequency domain, there's a heightened ca-pability to accurately characterize vibrations.

Structural deformations are one of the most significant factor that affects machine tool (MT) positioning accuracy. These induced errors are complex to be represented by a model, nevertheless they need to be evaluated and predicted in order to increase the machining performance. This paper presents a novel approach to calibrate a machine tool in real-time, analyzing the thermo-mechanical errors through Fibre Bragg Grating (FBG) sensors embedded in the MT frame. The proposed configuration consists of an adaptronic structure of passive materials, Carbon Fibre Reinforced Polymers (CFRP), equipped by FBG sensors that are able to measure in real-time the deformed conditions of the frame. By using a proper thermo-mechanical kinematic model, the displacement of the end effector may be predicted and corrected when it is subjected to external undesired factors. By starting from a set of FE simulations to develop a model able to describe the MT structure stresses, a prototype has been fabricated and tested. The scope was to compare the numerical model with the experimental tests using FBG sensors. The experimental campaign has been performed varying the structure temperature over time and measuring the tool tip point (TTP) positions. The obtained results showed a substantial matching between the real and the predicted position of TTP confirming the effectiveness of the proposed calibration system.

As the most serious of the many worse new pathological changes caused by diabetes, there are many risk factors for the occurrence and development of DR. It mainly includes hyperglycemia, hypertension, hyperlipidemia and so on. Among them, hyperglycemia is the most critical cause, which plays a key role in the pathological changes of DR.High-sucrose diets(HSDs) lead to elevated blood glucose levels in vivo, which, through oxidative stress, inflammation, the production of AGEs and VEGF, causes plenty of pathological damages to the retina and ultimately bring about loss of vision. The existing therapies for DR primarily target the terminal stage of the disease, when irreversible visual impairment has appeared. Therefore, early prevention is particularly critical. Early prevention of DR-related vision loss requires adjustments to dietary habits, mainly by reducing sugar intake. This article primarily discusses the risk factors, pathophysiological processes, and molecular mechanisms associated with the development of DR caused by HSDs. It aims to raise awareness of the crucial role of diet in the occurrence and progression of DR, promote timely changes in dietary habits, prevent vision loss, and improve the quality of life. The aim is to make people aware of the importance of diet in the occurrence and progression of DR. According to the dietary modification strategies we give, patients can change their poor eating habits timely, avoid the retinopathy that can be avoided theoretically, and obtain a excellent outcome.

Mitochondria are semiautonomous organelles, which are pivotal for the energy metabolism of eukaryotic cells. These organelles contain their own genetic system (mtDNA, mitogenome) that encodes to some structural RNAs and organellar proteins. The biogenesis and function of mitochondria is tightly regulated by nuclear-encoded protein cofactors. The mtDNAs of land plants are characteristically large, with a complex mode of gene organization and expression, in particularly at the post-transcriptional level. To become functional, the primary organellar transcripts undergo extensive maturation steps, which include endo- and exo-nucleolytic cleavage, RNA-base editing, and both ‘cis’- and ‘trans’-splicing events. These essential processing steps rely on the activities of a large set of nuclear-encoded factors. Among these, the RNA helicases serve as key players in organellar (mt-)RNA metabolism. This review summarizes the important roles played by these factors in regulating the highly dynamic processes of transcription, RNA processing, and translation within the mitochondria of land plants. We further discuss recent advancements in understanding how dysregulation of mitochondrial RNA helicases affects the organellar gene expression, respiratory functions, and hence the growth, development and physiology of land plants.

A PLS-based quality prediction method is proposed for batch processes using two-dimensional extended windows. To realize the adoption of information in the direction of sampling time and batch, a new definition region of support (ROS), k-i-back-extended region of support (KIBROS), is proposed to establish the extended window, which including the data of the previous sampling times in the same batch, the data of the same sampling time in the historical batches, the data of the previous sampling times in the historical batches and the data of the later sampling times in the historical batches. According to these regions of support, extended windows are established, and different models are proposed based on the extended windows for batch processes quality prediction. Further, using a typical batch process as an example, the injection molding process, the proposed quality prediction method is experimentally verified, proving that the proposed methods have higher prediction accuracy than the traditional method and the prediction stability is also improved.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

The vast array of interconnected microbes across earth’s ecosystems and within holobionts has been called the “Internet of Microbes.” Research into the fundamental microbial properties has demonstrated that bacteria and archaea are masters of energy and information collection, storage, transformation, and dissemination using both “wired” and wireless (at a distance) capacities. These features suggest that microbes are quantum entangled within and between earth’s holobionts, and that specific tools affecting energy and information functions could provide an effective strategy for managing microbial populations. Microbes use four critically important microbial networking functions (sound, light, electricity, and magnetism). This narrative review focuses on microbial management based on two of the four: sound and light (as well as related vibrations). These are examined as: 1) tools for managing microbial populations, 2) tools to support new technologies, and 3) tools for healing humans and other holobionts. Given microbial sensitivity to sound, light, and vibrations, it is critical that microbial populations and microbe-laden holobionts are protected from potentially damaging exposures. We conclude that sound, light, and vibrations are useful therapeutic tools that can help support useful microbial populations and help to address ongoing challenges of holobiont disease.

Many farms are replacing the lighting with light emitting diode (LED) bulbs because of the technological modernization. We aimed to investigate the effects of incandescent light (IL) and LED lighting on Cobb500 broiler chickens for six weeks. Production parameters (body weight, feed consumption, feed conversion ratio), calculated slaughter values (yield%, relative breast%, thigh%) and breast meat quality parameters (pH at 45 min and 24 h postmortem, color, drip loss, kitchen equipment losses, shear force, meat composition) were recorded. Non-stop recordings were used to analyze the behavior of the birds in several periods of the rearing. LED group was significantly better in body weigh parameter between week 1-5 and feed conversion ratio between week 2-3. The most significant difference in behavior was observed in the middle of the rearing period. The chickens in the LED group spent more eating time, drinking time, interacting, and resting less. There was no difference in the meat quality parameters, only shear force was significantly lower in the LED group (1781.95±0.33 g/s vs. 2098.82±0.42 g/s). Based on our results, LED lighting can bring positive changes in animal production efficiency, behavior, and important characteristics for meat consumers.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

This review aims to consolidate varied information regarding Port Scanning, and examine the tools, techniques, and detection algorithms used. It explores TCP SYN, Full TCP, UDP, and stealth scans, and shows their functions and abilities. Paired with these techniques, it also shows the tools that they can be used by, such as NMap, Zmap, and MASSCAN. It discusses the various detection techniques such as Signature and Anomaly based detection, and discusses the real world impact of this technology, while commenting on the legal and ethical issues posed.

Molecular visualisation is fundamental in the current scientific literature, textbooks and dissemination materials, forming an essential support for presenting results, reasoning on and formulating hypotheses related to molecular structure. Visual exploration has become easily accessible on a broad variety of platforms thanks to advanced software tools that render a great service to the scientific community. These tools are often developed across disciplines bridging computer science, biology and chemistry. Here we first describe a few Swiss Army knives geared towards protein visualisation for everyday use with an existing large user base, then focus on more specialised tools for peculiar needs that are not yet as broadly known. Our selection is by no means exhaustive, but reflects a diverse snapshot of scenarios that we consider informative for the reader. We end with an account of future trends and perspectives.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

In recent decades, as eutrophication in inland and coastal waters (ICWs) has increased due to anthropogenic activities and global warming, so has the need for timely monitoring. Compared with traditional sampling and laboratory analysis methods, satellite remote sensing technology can provide macro-scale, low-cost, and near real-time water quality monitoring services. The Geostationary Ocean Color Imager (GOCI), integrated onboard the Communication Ocean and Meteorological Satellite (COMS) from the Republic of Korea, was the first geostationary ocean color observation satellite and was operational from April 1, 2011 to March 31, 2021. Over ten years, GOCI has observed oceans, coastal waters, and inland waters within its 2,500 km×2,500 km target area centered on the Korean Peninsula. The most attractive feature of GOCI, compared with other commonly used watercolor sensors, was its high temporal resolution (1h, eight times daily from 0 UTC to 7 UTC), providing the opportunity to monitor the quality of ICWs, where optical properties can change rapidly throughout the day. This systematic review aims to comprehensively review GOCI features and applications in ICWs, analyzing progress in atmospheric correction algorithms and water quality monitoring. Analyzing 123 articles from the Web of Science and China National Knowledge Infrastructure (CNKI) through a bibliometric quantitative approach, we examined GOCI’s strength and performance with different processing methods. These articles reveal that GOCI played an essential role in monitoring the ecological health of ICWs in its observation area in East Asia. GOCI has led the way to a new era of geostationary ocean satellites, providing new technical means for monitoring water quality in oceans, coastal zones, and inland lakes. We also discuss the challenges encountered by geostationary satellites in monitoring water quality and provide suggestions for improvements.

Cell-culture meat is a novel concept to replace traditional meat produced from animals, and to satisfy rising food demands due to the world population growth. It is still a young field and requires to solve technical issues including cell sources and types, efficient culture for large scale production, taste and texture for customer satisfaction. The current review summarized traditional beef meat production and evaluation methods for customer satisfaction. In particular, serum biomarkers for beef meat evaluation are discussed, which can be applicated for cell-culture meat production.

Tea (Camellia sinenesis) is a health beneficial beverage and is also a source for extracting bioactive components such as theanine, tea polyphenols (TPP) and tea polysaccharides (TPS). TPS is a group of hetero-polysaccharides bounded with proteins. There were tests showing that TPS had various bioactivities, such as antioxidant, antitumors, antihyperglycemia, anti-inflammation and improving immunity. However, inconsistent results concerning chemical composition and bioactivity of TPS were published in recent years. The advances in chemical composition and bioactivities of TPS were reviewed in the present paper. The inconsistent and controversial results regarding composition and bioactivities of TPS were also discussed.

The paper delineates the developed vision system of the UR5 cobot and the operating algorithm of the robotic quality control station. The hardware-software architecture of the developed robotic station was shown, consisting of a UR5 cobot equipped with a web camera and a stationary industrial camera with a lighting system. Image processing and analysis algorithms were described, the method of control and communication between the station components was discussed, and two operating scenarios were presented as a single robotic station and a robotic line. Based on the results obtained, the level of measurement noise, accuracy, and repeatability of the developed vision system were estimated.

In the last five years, European research and innovation programmes have prioritised the development of online catalogues and tools (handbooks, models, etc.) to facilitate the implementation and monitoring of Nature Based Solutions (NBS). However, only a few catalogues and toolkits within European programmes are directly related to mainstreaming of NBS for food production (i.e., edible NBS). Therefore, the main aim of this paper is to present existing NBS tools through the eyes of productive urban landscapes. We reviewed 32 projects related to NBS and 50 tools were identified and characterised. Then, the 6 tools already available, and providing indicators, were further analysed in terms of their format and knowledge domains. Our main conclusion demonstrates that there is a lack of tools capable of supporting users for planning and implementing edible NBS, calculating the food potential of the city and/or of individual edible NBS, including the needed resources for implementation and operation (water, nutrients, energy), and assessing their urban design value, environmental and socio-economic impacts. And when they do exist, there is a resistance to share the models and equations behind the tools to allow other projects to reuse or validate them, fact which is contrary to Open Science principles stood up by many research public agencies.

Environmental monitoring programs rely on periodic spot sampling at specific locations, followed by laboratory analysis, aiming at the evaluation of water quality at a catchment scale. For this purpose, automatic telemetric stations for specific parameters have been installed by the Institute of Marine Biological Resources and Inland Waters of Hellenic Centre for Marine Research (IMBRIW-HCMR) within several Greek rivers and lakes, providing continuous and temporal monitoring possibilities. Nevertheless, the employment of unmanned surface vehicles (USV) equipped with integrated sensors represents a tool valuable to several monitoring strategies, offering enhanced temporal and spatial coverage over specific timeframes, allowing for targeted examination of sites or events of interest. The USVs have been deployed by Athens Water and Sewerage Company (EYDAP) as a cost-effective tool for the environmental monitoring of surface water bodies of interest, with emphasis on the spatial fluctuations of chlorophyllα, electrical conductivity, dissolved oxygen and pH, observed in Koumoundourou Lake and rivers Acheloos, Asopos and Kifissos. The effectiveness of an innovative heavy metal (HM) system installed in the USV for thein situ determination of copper and lead was also evaluated herewith. The results obtained demonstrate that both the timely detection of potential pollution from both anthropogenic activities and natural processes as well as the monitoring of inland waters are made feasible through the employment of USV.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

The supply chain has incorporated products by putting them into hair scarfs. This study introduces the use of mini chips in health and beauty products and can reduce fatigue through enhanced sleep patterns. The mini chip could be placed in the scarf and used as a prototype. RFID technology provides the supply chain with specific information that is used to identify products and make communication easier. (Muhammad, et. al. 2013) This paper presents a new tool herein referred to as a scarf prototype which is developed to analyse EMG (electromyogram), ECG (electrocardiography), EEG (electroencephalogram), and EOG (electro-oculogram) signals that focuses in the area of sleep disorders. The mini chips used can be used to determine a solution for sleep disruption by using automated analytics. This could lead to improvement in our understanding of sleep disruption and overall sleep physiology. Automated technology allows repeated measurements, evaluation of sleep patterns, and provide suggestions to improve a person’s quality of sleep. This analysis compares the use of polysomnography and the scarf prototype. The analytics provide models and shows correlation between variables, such as EMG, ECG, EEG, and EOG. This study shows that the results from the scarf prototype is just as reliable as the original method, polysomnography.

Honey is a sweet substance extensively consumed in the world for its nutritional and healthy properties. However, residues of pesticides and environmental contaminants can compromise its quality. For this reason, the physicochemical parameters, and the organic contamination of monofloral and multifloral honeys from three regions of Algeria (Tiaret, Laghouat and Tindouf) were monitored to evaluate the quality of honey and the safety for consumers. In general, the results obtained from the physicochemical analyses were in line with the EU standards. In terms of contamination, pesticides authorised and used in Algerian agriculture (matalaxyl-M and cyromazine), as well as banned pesticide (carbaryl), were found in almost all the samples. However, only the concentration of cyromazine was higher than the relative EU maximum residue levels. PCB 180, PCB 189, anthracene, fluorene and phenanthrene were mainly detected. All the honeys show traces of DiBP, DBP, DEHP and DEHT, but no traces of bisphenols were found. Moreover, the dietary exposure assessment shows that a small amount of Algerian honey can be safely consumed. Overall, data from this study should motivate the Algerian government to enhance their monitoring activities in beekeeping and to find solutions for implementing more sustainable agricultural practices harmonizing with the international legislation.

Metabolomics is now considered to be a wide-ranging, sensitive and practical approach to acquire useful information on the composition of a metabolite pool present in any organism, including plants. Investigating metabolomic regulation in plants is essential to understand their adaptation, acclimation and defense response to environmental stresses through the production of numerous metabolites. Moreover, metabolomics can be easily applied for the phenotyping of plants; and thus, it has great potential to be used in molecular breeding and genome editing programs to develop superior next generation crops. This review describes the recent analytical tools and techniques available to study plants metabolome, along with their significance of sample preparation using targeted and non-targeted method. Advanced analytical tools, like gas chromatography-mass spectrometry (GC-MS), liquid chromatography mass-spectroscopy (LC-MS), capillary electrophoresis-mass spectrometry (CE-MS), fourier transform ion cyclotron resonance-mass spectrometry (FTICR-MS) and matrix-assisted laser desorption/ionization (MALDI) have speed up metabolic profiling in plants. Further, we deliver a complete overview of bioinformatics tools and plant metabolome database that can be utilized to advance our knowledge to plant biology.

Wireless communication has proliferated due to the colossal augmentation of smart phones, mobile phones, tablets and laptops etc. Multimedia applications such as live videos, audios, still images, animated graphics and live communications all requires accompaniments of quality of service (QoS) as well as reliable end-to-end transfer of data. Information about the availability of resources in channel is must in order to improve the QoS. QoS can be determined in terms of capacity of channel, available bandwidth (ABW), and bulk transfer capacity (BTC). Bandwidth availability is a key check for improving the QoS in a network. The performance of a multimedia application is directly affected by the bandwidth availability. One of the most important QoS characteristic is ABW at a wireless route and it can be demarcated as least unused capacity of links instituting a network route. Since now there have been many bandwidth estimation techniques are available in the literature to increase the network performance. Bandwidth estimation techniques have been arranged into three leading classifications: i) Active probing bandwidth estimation techniques, ii) Passive bandwidth estimation technique and iii) Model based bandwidth estimation techniques. Each of these techniques are briefly discussed in this paper.

The concept of economic self-reliance, widely known by Thai people as the philosophy of sufficiency economy, has been widely promoted in rural Thai societies. By practicing this philosophy, it is expected that the citizens’ quality of life and local environments could be sustainably improved. This study aims to explore the contribution of the community practices of the sufficiency economy philosophy to rural villagers’ quality of life improvement, and to investigate potential factors that determine the trust of villagers in the philosophy. With the purpose to propose strategies which could enhance trust and promote villagers’ practices of the philosophy, the study investigated influences of three relevant factors on trust towards the philosophy. Those factors included factors related to cognitive-based trust, factors related to emotional-based trust, and factors related to demographic characteristics. Questionnaire surveys and in-depth interviews with community leaders and local villagers were conducted in the Ban Jamrung community, in Thailand’s Rayong province. The results of the statistical analysis revealed that the residents who applied the sufficiency economy philosophy in their daily lives experienced a relatively better quality of life. Additionally, it was found that trust in the philosophy could be predicted more by rational factors than by emotional factors. These findings could be utilized to develop strategies to maintain and enhance the trust of the people in the philosophy of sufficiency economy.

The recent advancement of Artificial Intelligence (AI) and Machine Learning (ML) tools has had a pervasive effect on every sphere of human existence. Libraries and information centres are not immune to these technological advances. These disruptive technologies have transformed the traditional face of libraries and their operations. There are many available AI tools, for example, chatbots, literature review tools, plagiarism detection tools, and several other developments in the field that have perhaps made the functioning of libraries easier. However, there is growing concern and uncertainty among both traditional library and modern professionals regarding the possible job loss and security issues related to these new technologies, which the professionals must deal with. Librarians and information professionals must be ready to handle the unforeseen situation. However, it is to be observed how libraries cope with these uncertainties, and threats to the integrity, availability of data, and normal library housekeeping functions.

Targeted Protein Silencing (TPS) is an elegant approach to investigate protein function and its role in the cellular landscape, overcoming limitations of genetic perturbation strategies. In contrast to CRISPR/Cas9 and RNA interference, these systems act in a reversible manner and reduce off-target effects. Several TPS have been developed and wisely improved, including compartment delocalization tools and protein degradation systems. In this review, we focus on Anchor-Away, deGradFP, auxin inducible degron (AID) and dTAG technologies, and discuss their recent applications and advances. Finally, we propose Nano-Grad, a novel nanobody-based protein degradation tool to specifically proteolyze endogenous tag-free target protein.

Emulsifiers like egg yolk (EY) are necessary for the formation of mayonnaise, which is an oil-in-water type colloid. This study aimed to assess the potential of defatted soybean powder treated with supercritical carbon dioxide (DSF-SC) in enhancing the quality of plant-based may-onnaise as plant-based alternatives gain popularity. This study involved producing DSF-SC and comparing its quality attributes to those of mayonnaise made with varying amounts of control soy flour (CSF), DSF-SC, and EY. It was found that mayonnaise made with DSF-SC, with increased emulsifier quantity, showed better emulsion stability, viscosity, and smaller, more uniform particle size compared with CSF mayonnaise. Additionally, DSF-SC mayonnaise was overall rated higher in sensory evaluation. The addition of approximately 2% DSF-SC positively influenced the emul-sion and sensory properties of the vegan mayonnaise, making DSF-SC a promising plant-based alternative emulsifier for replacing animal ingredients.

Electric torque wrenches play a crucial role in the assembly of high-strength bolts. This study focuses on three assembly processes for high-strength bolts and introduces a statistical analysis method to assess the quality of the bolt assembly. To enhance the performance, a novel, fully digital, Internet of Things (IoT) electric torque wrench is designed, incorporating a smart meter chip. This wrench achieves integration between the current sensor control method and the torque sensor control method using a simplified hardware circuit, ensuring high precision and stability. Additionally, this study employs the AC voltage self-stabilization method and Savitzky–Golay filtering method to enhance the accuracy and robustness of the wrench. Simulation experiments using Simulink and Matlab validate the effectiveness of these two methods. Furthermore, a cloud platform is utilized to enable rapid IoT access for the wrench, facilitating seamless connectivity and data transmission.

Contamination in coastal regions attributed to fluoride and nitrate cannot be disregarded, given the substantial environmental and public health issues they present worldwide. Maintaining water quality is crucial for environmental well-being. This comprehensive study was performed to assess the spatial as well as indexical water quality, identify contamination sources, and evaluate associated health risks pertaining to nitrate and flouride in AlHassa region, KSA. The physiochemical results revealed a pervasive pollution of the overall groundwater. The dominant water type was Na-Cl, indicating saltwater intrusion and reverse ion exchange impact. Spatiotemporal variations in physicochemical properties suggest diverse hydrochemical mechanisms, with geogenic factors primarily influencing groundwater chemistry. The groundwater pollution index varied between 0.8426 and 4.7172, classifying samples as moderately to very highly polluted. Similarly, the synthetic pollution index (in the range of 0.5021-4.0715) revealed that none of the samples had excellent water quality, with various degrees of pollution categories. Nitrate Health Quotient (HQ) values indicated chronic human health risks ranging from low to severe, with newborns being the most vulnerable. Household use of nitrate-rich groundwater for showering and cleaning did not pose significant health risks. Fluoride HQ decreased with age, and children faced the highest risk of fluorosis. The Hazard Index (HI) yielded moderate to high-risk values. Nitrate risks were 1.21 times higher than fluoride risks, as per average HI assessment. All samples fell into the vulnerable category based on the Total Hazard Index (THI), with 88.89% classified as very high risk. This research provides valuable insights into groundwater quality, guiding water authorities, inhabitants, and researchers in identifying safe water sources and vulnerable human populations. The results highlight the need for appropriate treatment techniques and long-term coastal groundwater management plans.

Background: the nature of alpha-D-mannose - natural aldohexose sugar, C-2 glucose epimer, whose intended use is for preventing urinary tract infections - in the interaction with E. coli is addressed in order to drive the issue of its regulatory classification as a medicinal product or medical device. Methods: PRISMA systematic review approach was applied; Delphi Panel method used to target consensus on statements retrieved from evidence. Results: Based of regulatory definitions and research evidences, the mechanism of D-mannose does not involve a metabolic or immunological action while there is an uncertainty regarding the pharmacological action. Specific interaction between the product and the bacteria within the body occurs, but its nature is inert: it does not induce a direct response activating or inhibiting body processes. Moreover, the action of D-mannose takes place, even if inside the bladder, outside the epithelium on bacteria that have not yet invaded the urothelial tissue. Therefore, its mechanism of action is not directed to host structures but to structures (bacteria) external to the host's tissues. Conclusions: From a regulatory perspective, D-mannose maintains the current medical device classification: new regulations and legal judgments can add further considerations. From a pharmacological perspective, research is driven versus synthetic mannosides: no further considerations are expected on alpha-D-mannose.

The importance of frailty in older people is getting constant recognition as an important aspect both in terms of public health, as well in personal level for the appropriate management of an older person health condition. This is reflected by the continuously increasing number of research studies carried out in several settings across different countries. Sometimes this is very solid, but in other cases there is a considerable gap in terms of accurate and well grounded documentation of frailty status. This is the case in Greece, where we are missing clinically validated tools to approach frailty. We are missing frailty screening tools, such as for instance PRISMA 7, the gold standard tool of Fried criteria is somehow problematic since the question referring to physical activity originates from a questionnaire that has not been translated and validated, while Clinical Frailty Scale has been validated for the translation but not for the capacity to detect frailty. Aim of this study is to validate these tools for their accuracy to detect frailty by using a measurable index of frailty, previously proposed for use in clinical studies: the Short Physical Performance Battery (SPPB). 74 male and female participants have been evaluated for their frailty status using different tools. We observed that PRISMA 7 translation detects frailty only when one question is removed at a cut-off of ≥ 2 and indicated a sensitivity of 88.1%, and specificity of 99.9% with a good correlation with SPPB measurements (r = 0.858; p < 0.001). When CFS was validated using SPPB it demonstrated a very good correlation (r = -0.838; p < 0.001 respectively) as it was the case for the modified Fried Criteria (r = -0.725; p < 0.001). All items demonstrated a good correlation between them. We can here propose that we can accurately assess frailty status in the community setting by using a modified version of Fried criteria, Clinical Frailty Scale translation in Greek and we can screen for frailty by using the Greek translation of PRISMA 7 only after removing the item 6 of the questionnaire.

The analysis and simulation of water quality in distribution networks is a complex issue of great concern today. The analysis of the evolution of water age, as a simple indicator of water quality in the network, is of great interest in both design and operation phases. Understanding the factors that have the strongest influence on water quality is key to developing adequate strategies aimed at preserving it. This paper firstly analyses the factors with biggest influence in the tanks water age, to support the selection of the most appropriate configuration from the point of view of water quality during design phases. Then, the main considerations when modelling tanks following the different mixing models considered in Epanet have been presented. Also, a real tank behaviour has been characterised through field measurements and Epanet simulations in order to determine the best fitted mixing model.

The European Union Water Framework Directive (2000/60/EC; WFD) aims to achieve a good ecological and chemical status of all bodies of surface water by 2027. The development of an integrated guidance on surface water chemical monitoring (e.g. WFD Guidance Document No. 7/19) has been transferred into national German law (Ordinance for the Protection of Surface Waters, OGewV). For the majority of compounds, this act requires a monthly sampling frequency to assess the chemical water quality status of a surface water body. To evaluate the representativeness of the sampling strategy under the OGewV, high-frequency online monitoring data is investigated under different sampling scenarios and compared with current, monthly grab sampling strategy. About 23 million data points were analyzed for this study, three chemical parameters (dissolved oxygen, nitrate-nitrogen, chloride concentration) and discharge data were selected from four catchment of different sizes ranging from 51391 km² to 84 km² (Elbe, Vereinigte Mulde, Neiße and two stations at Lockwitzbach). In this paper we proposed short-term online-monitoring (STOM) as a sampling alternative. STOM considers the placement of online sensors over a limited duration and return interval. In general we: (I) compare the results of conventional grab sampling with STOM, (II) investigate the different performance of STOM and grab sampling using discharge data as proxy for analyzing event-mobilized pollutants and (III) investigate the related uncertainties and costs of both sampling methods. Results show, that STOM outperforms grab sampling for parameters where minimum/maximum concentrations are required by law as the probability to catch a single extreme value is higher with STOM. Furthermore, parameters showing a pronounced diurnal pattern, like dissolved oxygen, are also captured considerably better. The performance of STOM showed no substantial improvements for parameters with small concentration variability, as nitrogen-nitrate The analysis of discharge events as a proxy parameter for event-mobilized pollutants proved that the probability of capturing samples during events is significantly increased by STOM.

Lactoperoxidase system (LPS) effect on quality of raw and pasteurized milk under real conditions along the dairy value chain in Ethiopia was evaluated. A total of 250 milk samples were collected from farmers, collectors, and factories. Experimental samples were LPS-activated of morning and overnight milk. The samples were tested with several chemical and microbiological tests such as total bacterial count (TBC), total coliform count (TCC) and Escherichia coli count (EC). Results indicated that all LPS-activated milk samples had a higher quality than all the control samples. For instance, both the morning and overnight farm milk samples had a mean TBCs of 5.79 log and 6.55 log cfu/ml which is significantly (p

Streptococcus pneumoniae is the causative agent of a multitude of diseases and further study into its pathogenies is vital. The pneumococcus is genetically malleable and several tools are available to manipulate this pathogen. In this study, we attempted to utilize one such tool, the Sweet Janus cassette, to replace the capsule locus with other capsule loci in our strain background and found that the efficiency of allelic replacement was low and the number of revertant false-positive colonies was high. We determined that the capacity to recombine capsule varied by the initial isolated colony, suggesting that frequency of reversion is dependent on the bacterial cell line. Alternative selection markers may further expand the application of Sweet Janus. We created novel cassettes that utilized chlorinated phenylalanine as an alternative counter-selection agent in conjunction with the Janus or Sweet Janus cassette, providing a new dual or triple selection marker. Moreover, we created cassettes that do not require engineered resistance in the background strain, including both single and dual selection markers. We were able to utilize all constructs in allelic replacement of the capsule loci. These novel constructs provide a new means for generating gene deletions in S. pneumoniae that expand experimental applications.

In the smart city, information and communications technologies (ICTs) are proposed as solutions to urban challenges, including sustainability concerns. While sustainability commonly refers to economic and environmental dimensions, the concept also contains a social component. Our study asked how smartphone applications (apps) address social sustainability challenges in urban transport, if at all. We focused on transport disadvantages experienced due to low income, physical disability, and language barriers. A review of 60 apps showed that transport apps respond to these equity and inclusion issues in two ways: (a) by employing universal design in general-use apps; including cost-conscious features; and providing language options (b) by specifically developing smartphone apps for persons with disabilities. The article discusses the study by positioning it in the literature of smart cities as well as socially sustainable transport.

In recent years the number of available chemical pesticides has been significantly reduced and there have been an urgent need for discovery of alternative to chemical pesticides products, as among others the natural zeolites (zeolitic rocks). We determined the mineralogical and chemical composition of a specific and continuous layers of zeolitic rock sample (ZeotP) from Petrota, Ev-ros, Greece and evaluated its oviposition deterrent effect for the olive fruit fly Bactrocera oleae (Diptera: Terphritidae). The tested natural zeolite contained 70 wt. % Clinoptilolite, 18 wt. % Amorphous material, 7 wt. % Feldspars, 4 wt. % Cristobalite and 1 wt. % Quartz. We tested the oviposition deterrent effect of ZeotP mixed or not with an emulsifier adjuvant NU-FILM-P® in water and applied on the surface of olive fruits. The ZeotP oviposition deterrent effect for the ol-ive fly was very high under a series of tested temperatures (17°C, 20°C, 25°C and 30°C) and RHs (23%, 33%, 55%, 75%, 94%). In addition, the ZeotP residual deterrent effect after equable water spraying was high and similar to the respective effect of a pyrethroid insecticide (Decis®). Our results may contribute to an effective control of the olive fruit fly using an alternative to chemical pesticides natural zeolite (zeolitic rocks) product.

An influenza A virus (H3N2) with an envelope with the same structure as COVID-19 was used for antiviral testing of material surfaces, in comparison with some results of feline calicivirus. The evaluation method used was the film adhesion method, in which the virus solution is placed on the material and adhered to it using a film. The evaluation method was based on the film adhesion method, in which the virus solution is placed on the material and adhered with a film, and the plaque method, in which the cell virus is allowed to infect the material and form plaques, but the appropriate virus concentration must be adjusted to observe the plaques. When not under that restriction, the plaques are often incomplete; this is observed. For this reason, this study applied an area measurement method that can reflect viral activity even when plaques are not obtained. This study revealed that different types of metallic materials have different antiviral properties. Specifically, the antiviral activity of iron, carbon steel, and nickel was relatively high, while that of stainless steel and titanium was relatively low. The order of antiviral activity was as follows: Fe, SS400, Ni, SUS316L, SUS304, and Ti.

In this world that we share with them, they became unintended sentinels for the consequences of pollutant exposure, developing similar conditions to humans, and even earlier. This review focuses on the human-pet interaction and on the effects of the environment pets share with us. Alongside other species, canine and feline companions are veritable models in human medical research. The latency period for showing chronic exposure effects to pollutants is just a few years in them, compared to considerably more, decades in humans. Comparing the serum values of man's best friends to ours can indicate the degree of poisonous lead-load we are exposed to, for example, and of other substances as well. We can find 2.4 times higher perfluorochemicals from stain- and grease-proof coatings in canine companions, 23 times higher values for PBDEs in cats, and five times more mercury compared to the average levels obtained in humans. All these represent early warning signals. Taking into account all these, and the animal welfare orientation of today’s society, finding non-invasive methods to detect the degree of environmental pollution in our animals becomes paramount, alongside with the need to raise awareness on the risks carried by certain chemicals we knowingly use.

A growing body of evidences is showing that dysbiotic gut microbiota may correlate with a wide range of disorders; hence, the clinical use of microbiota maps and fecal microbiota transplantation (FMT) can be exploited in the clinic of some infectious diseases. Through direct or indirect ecological and functional competition, FMT may stimulate decolonization of pathogens or opportunistic pathogens, modulating immune response and colonic inflammation, and restoring intestinal homeostasis, with reduction of host damage. Herein, we discuss how diagnostic parasitology may contribute to design clinical metagenomics pipelines and FMT programs, especially in pediatric subjects. The consequences of a more specialized diagnostics in the context of gut microbiota communities may improve the clinical parasitology and extend its applications to the prevention and treatment of several communicable and even noncommunicable disorders.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Until recently, no disease-specific health-related quality of life (HRQoL) instrument existed for pediatric traumatic brain injury (TBI). In this revalidation study, the psychometric properties and the validity of the final German version of the 35-item QOLIBRI-KID/ADO questionnaire were examined in 300 children and adolescents. It is the first self-reported TBI-specific instrument for measuring pediatric HRQoL in individuals aged 8–17 years. The six-factor model fits the data adequately. Internal consistencies were excellent for the total score and satisfactory to excellent for the scale scores. Intraclass correlations indicated good test-retest reliability. Construct validity was supported by overlaps between the QOLBRI-KID/ADO and the PedsQL, which measures generic HRQoL. Discriminant validity indicated that HRQoL was significantly lower in older children and girls, and in those with anxiety, depression, and post-concussion symptoms than in comparison groups, replicating the results of the questionnaire’s first development study. Our results suggest that the QOLIBRI-KID/ADO is a valid and reliable multidimensional instrument for assessing disease-specific HRQoL after pediatric TBI in clinical and research settings, which can additionally be used across the lifespan in combination with the adult version. This may help to improve care, treatment, daily functioning and HRQoL after TBI.

The fish supply chain (FSC) industry faces a significant challenge in terms of maintaining fish quality and authenticity throughout the chain. The main goal of modern FSC systems is tracking and tracing the fish product at each stage, from harvester to end customer, as well as assessing its quality and authenticity. Integrating FSC with new technologies, such as Blockchain (BC), Big Data, Artificial intelligence (AI), and Internet of Things (IoT), enhances fish product traceability, authenticity, visibility, and security. We propose a BC-based FSC framework that follows a layered architecture consisting of a SC layer, an IoT layer, and a BC layer. We integrate a new AI-based hand-held device, a Quality, Adulteration & Traceability (QAT) device, that can identify fish species and assess fish quality. We leverage the key features of BC and smart contracts, deployed over the Ethereum platform for the proposed framework integrated with QAT technology. Extensive validation of smart contracts is conducted to prove its practical feasibility.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

This paper presents a case study on using Emacs and Org-mode for literate programming in undergraduate data science courses. Over three academic terms, the author mandated these tools across courses in R, Python, C++, SQL, and more. Onboarding relied on simplified Emacs tutorials and starter configurations. Students gained proficiency after initial practice. Live coding sessions demonstrated the flexible instruction enabled by literate notebooks. Assignments and projects required documentation alongside functional code. Student feedback showed enthusiasm for learning a versatile IDE, despite some frustration with the learning curve. Skilled students highlighted efficiency gains in a unified environment. However, uneven adoption of documentation practices pointed to a need for better incorporation into grading. Additionally, some students found Emacs unintuitive, desiring more accessible options. This highlights a need to match tools to skills levels, potentially starting novices with graphical IDEs before introducing Emacs. Key takeaways include literate programming aids comprehension but requires rigorous onboarding and reinforcement; Emacs excels for advanced workflows but has a steep initial curve. With proper support, these tools show promise for data science education.

Ecological corridors function as a viable way to mitigate the environmental impact arising from forest fragmentation by interconnecting forest fragments through various techniques. In this context, the objective of this study is to propose a route for the implementation of an ecological corridor in the Itapemirim river watershed. The specific objectives were: (i) to delimit the permanent preservation areas (APP) of the Itapemirim river watershed and compare land use and land cover in the delimited areas; (ii) to calculate landscape ecology indices and select the forest fragments with the highest potential for ecological corridor implementation using Fuzzy logic; (iii) to assess costs and trace the best route for ecological corridor implementation, considering distance and physical impediments; (iv) to assess land costs and expropriation costs to delimit the ecological corridor in the study area. To map land use and land cover, the MapBiomas platform was used, based on Landsat 8 satellite images. The permanent preservation areas were delimited according to criteria established by Law No. 12.651 of May 25, 2012, which establishes parameters, definitions, and limits for APP. The characterization and structural quantification of some landscape ecology indices were performed using the QGIS 3.26 computational application, through the LecoS 3.0.1 plugin and Fragstats 4.2. The connected forest fragments were the Caparaó National Park, the Serra das Torres State Natural Monument, and the fragments selected through the application of Fuzzy logic to the landscape ecology indices. The corridor was delimited according to the lowest cost route, considering land use and land cover, APP, fragment potential, slope, and subnormal clusters. For each cost raster image, its respective statistical weights were calculated using the Analytic Hierarchy Process (AHP) hierarchical method, as well as for the analysis of priority areas for forest restoration, considering land use and land cover, APP, pedology, lithology, and biological importance. The interconnection between protected areas and fragments with the ecological corridor followed the orientation described by CONAMA nº 09/96. Based on the development of the work, the following results were identified: the highest land use and land cover class is pasture. Of the area designated for permanent preservation, 68.58% is in conflicting use with the legislation. The bare land value per hectare of the pasture class is the second highest among the bare land value per LULC values, representing 64.28% of the total. The priority area map showed that 31.86% of the area was classified as of very high or high importance and 42.97% as low or very low priority for forest restoration. Thus, it is concluded that the least cost path algorithm associated with the result generated by the multi-criteria decision method (AHP) constitutes an important tool for planning and implementing an ecological network by taking into account the primary factors for decision-making regarding the location of the best route.

The development of Imaging Atmospheric Cherenkov Telescopes (IACTs) unveiled the sky in the teraelectronvolt regime, initiating the so-called “TeV revolution” at the beginning of the new millennium. This revolution was also facilitated by the implementation and adaptation of statistical tools for analyzing the shower images collected by these telescopes and inferring the properties of the astrophysical sources that produce such events. The image reconstruction techniques, the background discrimination and the signal-detection analyses are just a few of the pioneering studies applied in the last decades in the analysis of IACTs data. This (succinct) review has the intent of summarizing the most common statistical tools that are used for analyzing data collected with IACTs, focusing on their application in the full analysis chain, giving references to the past literature for a deepened examination.

Enzymes are in high demand for very diverse biotechnological applications. However, natural biocatalysts often need to be engineered for fine-tuning their properties towards the end applications, such as the activity, selectivity, stability to temperature or co-solvents, and solubility. Computational methods are increasingly used in this task, providing predictions that narrow down the space of possible mutations significantly and can enormously reduce the experimental burden. Many computational tools are available as web-based platforms, making them accessible to non-expert users. These platforms are typically user-friendly, contain walk-throughs, and do not require deep expertise and installations. Here we describe some of the most recent outstanding web-tools for enzyme engineering and formulate future perspectives in this field.

Gender-based violence is considered a serious social and public health problem. Overcoming this situation implies a process that results in the favorable biopsychosocial rehabilitation, the resilient of women. The objective of this study was to analyze the tools, resources and personal and psychosocial mechanisms used by women survivors of gender-based violence. The design was an interpretative phenomenology. It carried out with 22 women who have overcome gender-based violence. Data was collected through personal interviews and narration. The results were grouped into four themes: "Process of violence", "Social resources for coping and overcoming GBV", "Personal tools for coping and overcoming GBV", and "Feelings identified, from the abuse stage to the survival stage". Several studies concluded that overcoming abuse is influenced by the women social network, and it can be the action of these people determining their survival to gender violence. Despite the recognized usefulness of these available resources, it would be desirable to strengthen them in order to be able to drive more women toward survival, assuming a strengthening of coping and overcoming, without forgetting the importance of other support mechanisms such as their family and group therapies.

The paper summarizes in a step by step ‘recipe’ format a model of developing new ideas (Ideation) that can be used to form a new venture or develop a new product. The proposed ‘recipes’ are widely used and can be applied in tandem with other prevalently available models or tools. The intention of the paper is also to serve as a resource for entrepreneurs and innovators, and the links and references munificently used in the paper are serving this purpose. The author has used the outline and the tools described here in numerous Ideation classes taught for over a decade in several countries around the world. The paper’s intention is not to conduct a systematic review on the subject of new venture creation or propose new research agenda (for that, see for example Shepherd et al., 2021). The purpose is to provide an effective and efficient set of tools, models and techniques that can assist the entrepreneur in her journey to create and achieve her dreams. One such tool is the matrix of Reasonings-Outcomes introduced here for the first time.

Many manufacturing sectors require high surface finishing. After machining operations such as milling or drilling, undesirable burrs or insufficient edge finishing may be generated. For decades, many finishing processes have been handmade-basis; this fact is accentuated when dealing with complex geometries especially for high value-added parts. In recent years, it’s a tendency of trying to automate as far as possible this kind of processes, repeatability and time/money savings are main purposes. Based on that idea, the aim of this work is to check new tools and strategies for finishing aeronautical parts, especially critical engine parts made on Inconel 718, a very ductile nickel alloy. Automating edge finishing of chamfered holes is a complicated but really important goal. In this paper, flexible abrasive tools were used for this purpose. A complete study of different abrasive possibilities was carried out, mainly focusing on roughness analysis and final edge results obtained.

Malassezia species are part of human commensal microbiota and is also related to diseases. Little is known about the interaction of these microorganisms with their host. Here we established two standard culture conditions for Malassezia spp. to perform infection assays using C. elegans and T. molitor. Invertebrate hosts infected by Malassezia spp. cultured in M9M resulted in higher death rate on survival assays when compared to yeasts cultured in standard Dixon medium indicating that M9M cultured Malassezia species have increased virulence. The culture and infection conditions established in this work, using invertebrate alternative models, are valuable tools to understand Malassezia-host interaction.

The quality of healthcare services is a very important indicator of social welfare in developed and emerging countries. Good quality levels are critical to ensuring patient safety, improving health outcomes, increasing patient satisfaction, optimizing resource utilization, and meeting regulatory requirements. The stable and sustainable operation of medical institutions urgently requires the establishment of a reliable and effective medical quality performance evaluation platform. However, the complexity of the evaluation process, involving numerous evaluators and the consideration of different subjective and objective criteria, poses significant challenges and essentially constitutes a group multi-criteria decision-making problem. This article uses the overall medical environment of the institution, medical service attitude, medical security, administrative service measures, etc. as measurement standards to deal with this challenge. It proposes a medical service quality measurement model suitable for both qualitative and quantitative analysis. In view of the heterogeneity of information, the two-tuple fuzzy language calculation method is introduced to enable evaluators to skillfully manage diverse information and effectively avoid potential information omission problems in the subjective evaluation integration process. The effectiveness and feasibility of the model were demonstrated by applying it to the operational framework of a medical institution in central Taiwan.

The aim of this research work is to study the influence of temperature, solar irradiation and wind dust on the production of solar energy. In addition, it aims to study the assessment of water quality, in particular groundwater used for cooling and cleaning photovoltaic panels (quality analysis). it's an important source, stable and sustainable can be used entirely for cooling and cleaning PV modules from the sales dust, in order to improve their performance. To date, all research studies carried out in this context of cooling and cleaning using water have not taken account of the nature of this water. We have taken a sample of water from a well in a rural area in the Darra Tafilalet region of Morocco. This region has an arid and semi-arid climate, with very high temperatures and dust-laden winds, particularly in summer. These meteorological characteristics influence the efficiency of cells, particularly photovoltaic (PV) panels, reducing their performance. Next, the water sample was analysed in the laboratory. The results obtained show that the groundwater in this area is very sensitive to cooling and cleaning photovoltaic panels. Moreover, these results indicate that the temperature, solar irradiation and wind-blown dust have a significant influence on energy production.

Stream chemistry effectively integrates watershed ecosystem processes on both spatial and temporal scales. Streams of coastal areas integrate a more homogeneous, flat topography wherein there can be interactions between the stream and the body of water into which it drains, especially where tidal fluxes occur. The present study assessed water quality of Thompson Bayou, which comes to the campus of the University of West Florida in a wetland after flowing through 4 km of commercial and private property with associated impacts on water quality. Sampling was carried out for one year at eight discrete sites along Thompson Bayou from the UWF campus to the Escambia River. We used a portable field meter to measure temperature, pH, dissolved O2 (DO), and specific conductivity (SC). Except for temperature, all variables exhibited a spatial pattern of significant variation with distance, with consistent increases in DO and SC as the stream approached the river. These variables also exhibited a temporal pattern of significant seasonal variation, including—and especially—temperature. Data suggest that spatial and temporal patterns of water quality of Thompson Bayou are determined by (1) processing of water by the wetland, (2) interactions of the stream channel with upland forest stands, and (3) the tidal hydrology of the Escambia River.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

In recent years, unmanned aerial vehicles (UAVs) have become a valuable platform for many applications, including communication networks. UAV-enabled wireless communication faces challenges in complex urban and dynamic environments. UAVs can suffer from power limitations and path losses caused by non-line-of-sight connections, which may hamper better communication performance. To address these issues, reconfigurable intelligent surfaces (RIS) have been proposed as a helpful tool to enhance UAV communication networks. However, due to the high mobility of UAV, complex channel environments, and dynamic RIS configurations, it is challenging to estimate the link quality of ground users. In this paper, we propose a link quality estimation model using a gated recurrent unit (GRU) to assess the link quality of ground users for a multi-user RIS-assisted UAV-enabled wireless communication system. Our proposed framework uses a time series of user channel data and RIS phase shift information to estimate the quality of the link for each ground user. Simulation results showed that the proposed GRU model effectively and accurately estimates the link quality of the ground users in the RIS-assisted UAV-enabled wireless communication network.

China is experiencing rapid urbanization. The focus on health issues has shifted from the treatment of diseases to passive or active prevention. Diseases caused by the deterioration of the urban environment, such as cardiovascular disease, diabetes, obesity and other chronic diseases and mental illness, have gradually become the main threat to public health. Studies have confirmed that urban green spaces (UGS) can help residents relieve mental stress, improve mood, reduce mental fatigue and restore attention, which has a positive effect on people's physical and mental health. In this study, the relationship between the quantity and quality factors of UGS and the physical and mental health of urban residents in Xihu District of Hangzhou is examined, and on this basis, UGS design strategies are proposed to promote the physical and mental health of residents. This study is of great significance for the future construction of UGS that are beneficial to the health of residents and the promotion of a healthy China and healthy city construction.

Rangelands are a key resource present all over the world as it covers half of emerged lands. They are even more important in drylands, where they cover 48% of the total area. Intensification and the additional pressure added by climate change push these systems towards desertification. Over the last two decades, we have developed and applied System Dynamics (SD) models for the study of Mediterranean grasslands. In addition, we have developed procedures and analysis tools, such as global sensitivity analysis, stability analysis condition, or risk analysis, in order to detect the main drivers of these socio-ecological systems and provide indicators about their long-term sustainability. This paper reviews these works, their scientific background, and the most relevant conclusions, including purely technical and rangeland-related ones as well as our experience as systemic modelers in a world driven by field specialists.

Nickel-based superalloys are attractive to many industrial sectors (automotive, military, energy, aerospace etc.). However, their physical properties make them difficult to machining using traditional tools. Therefore, the new materials for the machining of Ni-based alloys are required. Ceramic-based composites could act as a tool to replace the current materials. The incentives for this paper are to provide an overview of existing ceramic composites and draw some conclusions that will help in solving the problem of choosing materials for processing of Ni-based superalloys. Despite the diversity of ceramic composites in this work the focus was on the SiAlON ceramic.

The diagnosis and treatment of autoimmune diseases are major challenges. Their signs, symptoms, and their clinical severity change throughout the course of the disease. The available treatments for these conditions do not result in complete remission, and their long-term use generates several side effects. The main challenges in this field are the development of more sensitive diagnostic tools, and effective treatments. Studies in patients and animal models reported alterations in monocyte phenotype, activation, and function. These cells play an essential role in the pathogenesis of chronic inflammatory states and have become a target for extracorporeal monitoring and specific intervention. Nanoparticles (NPs) are ultrafine particles that can be used as contrast agents in diagnostic imaging techniques to detect specific cells in inflammatory infiltrates in tissues that are not easily accessible by biopsy. In addition, NPs can be designed to deliver drugs to a cell population or tissue. This review describes several experimental pieces of evidence demonstrating that monocytes and macrophages can specifically uptake various types of NPs, thus becoming detectable in vivo by magnetic resonance imaging and susceptible to be modulated by therapeutic agents. Hence, nanoparticles targeting mononuclear phagocytes represent promising tools for diagnosing and treatment.

The multidisciplinary nature of the work required for research in the Covid-19 pandemic has created new challenges for health professionals in the battle against the virus. They need to be equipped with novel tools and resources ---that have emerged during the pandemic--- to gain access to breakthrough findings, know the latest developments, and to address their specific needs for rapid data acquisition, analysis, evaluation, and reporting. Because of the complex nature of the virus, the healthcare systems worldwide are severely impacted as the treatment and the vaccine for Covid-19 disease are not yet discovered. This leads to frequent changes in regulations and policies by governments and international organizations. Our analysis suggests that given the abundance of information sources, finding the most suitable tool for a given task is one of such challenges. But health professionals and policymakers need access to the most relevant, reliable, trusted, and latest information and tools that can be used in their day-to-day tasks of Covid-19 research and analysis. In this article, we present our analysis of various novel and important tools that have been specifically developed during the Covid-19 pandemic and that can be used by the health professionals community to help in advancing their analysis and research. These tools comprise of search engines, information repositories for literature and clinical trials, data sources, dashboards, and forecasting models. We present list of the minimally essential tools to serve a multitude of purposes, from hundreds of those developed since the beginning of the pandemic. A critical analysis is provided for the selected tools based on 17 parameters that can be useful for researchers and analysts for their evaluations. These parameters make up our evaluation framework and have not been used previously for analysis and evaluation. Hence, knowledge of the tools will not only increase the productivity but will also allow to explore new dimensions for using existing tools with more control, better management, and greater outcome of their research. In addition, the parameters used in our framework can be applied for future evaluations of similar tools and health professionals can adapt them for evaluation of other tools not covered in this analysis.

The objective of this study is to examine different types of bias present in assessment tools and techniques, identify and eliminate any forms of favoritism, and suggest effective approaches for advancing equity and objectivity in assessment procedures. The research utilizes a qualitative methodology, incorporating surveys and focus group discussions with educators and students to collect data. Thematic analysis is a method employed for the purpose of analyzing qualitative data. The results suggest that students hailing from diverse cultural backgrounds perceive partiality in the language and cultural context of evaluations, leading to diminished scores. According to academic professionals, standardized tests are subject to bias, and offering accommodations that cater to linguistic and cultural diversity may improve the academic achievement of students from diverse cultural backgrounds. The findings of this research are of great importance to professionals in the domains of education, policy development, and academia who seek to improve assessment practices and promote equitable educational opportunities for all learners.

Rapid advances in the screening, diagnosis, and treatment of genetic disorders has increased the number of conditions that could be detected through universal newborn screening (NBS). However, addition of conditions to the Recommended Uniform Screening Panel (RUSP) and implementation of nationwide screening has been a slow process taking several years to accomplish for individual conditions. Here we describe web-based tools and resources developed and implemented by the newborn screening translational research network (NBSTRN) to advance newborn screening research and support NBS stakeholders. NBSTRN’s tools include the Longitudinal Pediatric Data Resource (LPDR), the NBS Condition Resource (NBS-CR), the NBS Virtual Repository (NBS-VR), and the Ethical, Legal, and Social Issues (ELSI) Advantage. Research programs including the Inborn Errors of Metabolism Information System (IBEM-IS), BabySeq, EarlyCheck, and Family Narratives Use Cases have utilized NBSTRN’s tools, and in turn contributed research data to further expand and refine these this resource. Additionally, we discuss ongoing tool development to facilitate expansion of genetic disease screening in increasingly diverse populations. In conclusion, NBSTRN’s tools and resources provide a trusted platform to enable NBS stakeholders to advance NBS research and improve clinical care for patients and their families.

In the context of growing global political tension and introduction of world trade barriers, the urgent task is to develop new tools for assessing their consequences. In the paper we present the agent-based model of trade wars, considering organizations, states and residents generated using initial statistical data. Simulation determines changes in output and supplies of organizations under trade restrictions. Results of calculations on the developed model and comparison of various model complexes forecasts with real consequences of trade wars between the USA and China in 2018 and Western countries against Russia in 2022 are presented. Within calculations four scenarios were considered: (1) baseline, (2) new restrictions between China and the USA, (3) more serious sanctions against China and Russia by the USA and the EU, (4) a global trade war. In the second scenario deviation GDP of the USA and China from the baseline scenario does not exceed 0.5%. In the third scenario, the range of countries involved is expanding, and the fall in GDP in them is expected at the level of 0.7-1%. In the fourth scenario, the entire world economy experiences a serious slowdown, and the EU are facing the most severe consequences, going into recession.

Measuring bias is important as it helps identify flaws in quantitative forecasting methods or judgmental forecasts. It can, therefore, potentially help improve forecasts. Despite this, bias tends to be under-represented in the literature: many studies focus solely on measuring accuracy. Methods for assessing bias in single series are relatively well-known and well-researched, but for datasets containing thousands of observations for multiple series, the methodology for measuring and reporting bias is less obvious. We compare alternative approaches against a number of criteria when rolling-origin point forecasts are available for different forecasting methods and for multiple horizons over multiple series. We focus on relatively simple, yet interpretable and easy-to-implement metrics and visualization tools that are likely to be applicable in practice. To study the statistical properties of alternative measures we use theoretical concepts and simulation experiments based on artificial data with predetermined features. We describe the difference between mean and median bias, describe the connection between metrics for accuracy and bias, provide suitable bias measures depending on the loss function used to optimise forecasts, and suggest which measures for accuracy should be used to accompany bias indicators. We propose several new measures and provide our recommendations on how to evaluate forecast bias across multiple series.

Faba bean (Vicia faba L.), a member of the Fabaceae family, is one of the important food legumes cultivated in cool temperate regions. It holds great importance for human consumption and livestock feed because of its high protein content, dietary fibre, and nutritional value. Major faba bean breeding challenges include its mixed breeding system, unknown wild progenitor, and genome size of ~13 Gb, which is the largest among diploid field crops. The key breeding objectives in faba bean include improved resistance to biotic and abiotic stress and enhanced seed quality traits. Major progress on reduction of vicine-convicine and seed coat tannins, the main anti-nutritional factors limiting faba bean seed usage, have been recently achieved through gene discovery. Genomic resources are relatively less advanced compared to other grain legume species, but significant improvements are underway due to a recent significant increase in research activities. A number of bi-parental populations have been constructed and mapped for targeted traits in the last decade. Faba bean now benefits from saturated synteny‐based genetic maps, along with next-generation sequencing and high-throughput genotyping technologies that are paving the way for marker-assisted selection. Developing a reference genome, and ultimately a pan-genome, will provide a foundational resource for molecular breeding. In this review, we cover the recent development and deployment of genomic tools for faba bean breeding.

There is increasing use of wood-based composites in industry not only because of the shortage of solid wood, but above all for their better properties such as: strength, aesthetic appearance, etc. compared to wood. Medium density fibreboard (MDF) is a wood-based composite that is widely used in the furniture industry. The goal of the research conducted was to determine the effect of the type of coating on the drill cutting blades on the value of thrust force (F_t), cutting torque (M_c), cutting tool temperature (T) and surface roughness of the hole in drilling MDF panels. In the tests three types of carbide drills (HW) were used: not coated, TiAlN coated and ZrN coated. The measurement of both the thrust force and the cutting torque was carried out using an industrial piezoelectric sensor. The temperature of the cutting tool in the drilling process was measured using an industrial temperature measurement system using a K-type thermocouple. It was found that the value of the maximum temperature of the tool in the drilling process depends not only on the cutting speed and feed rate, but also on the type of coating of the cutting tool. The value of both the cutting torque and the thrust force is significantly influenced by the value of the feed rate and the type of drill coating. The effect of varying plate density on the surface roughness of the hole and the variation of the value of the thrust force is also discussed. The results of the investigations were statistically analysed using a multi-factorial analysis of variance (ANOVA).

Traditional methods for discovery and development of new drugs can be a very time-consuming and expensive process because it includes several stages such as compound identification, pre-clinical and clinical trials before the drug is approved by the US Food and Drug Administration (FDA). Therefore, drug repurposing, namely using currently FDA-approved drugs as therapeutics for other diseases than what they are originally prescribed for, is emerging to be a faster and more cost-effective alternative to current drug discovery methods. In this paper, we have described a three-step in silico protocol for analyzing transcriptomics data using online databases and bioinformatics tools for identifying potentially repurposable drugs. The efficacy of this protocol was evaluated by comparing its predictions with the findings of two case studies of recently reported repurposed drugs: HIV treating drug Zidovudine for the treatment of Dry Age-Related Macular Degeneration and the antidepressant Imipramine for Small-Cell Lung Carcinoma. The proposed protocol successfully identified the published findings, thus demonstrating the efficacy of this method. In addition, it also yielded several novel predictions that have not yet been published, including the finding that Imipramine could potentially treat Severe Acute Respiratory Syndrome (SARS), a disease that currently does not have any treatment or vaccine. Since this in-silico protocol is simple to use and does not require advanced computer skills, we believe any motivated participant with access to these databases and tools would be able to apply it to large datasets to identify other potentially repurposable drugs in the future.

There are many modern and traditional methods in valuing the performance of the company among them EVA, CVA are modern methods where as EPS, ROI, ROE etc. are some of the traditional methods. modern and traditional methods are not only used to check the performance of a company but it also used in investment decisions by the investors. Stern Stewart, managing partner of M/s Stern Stewart & Co. introduced a modified concept of economic profit in 1990 in the name of Economic Value Added (EVA) as measure of business performance and CVA is only a cash consideration in EVA. In this paper an attempt is made to study which method is used by the investors while taking the investment decisions i.e. traditional methods are modern methods. 100 respondents (Investors) are questioned and collected their views, we are assuming that there is no impact of traditional or modern methods while taking investment decisions by the investors.

A global approach towards quality management highlights the need for constructing a new body of knowledge that views the field of global quality from a systems perspective. Based on the results of field experiments, and in light of the need to develop new global quality management terminology, the current article presents several key concepts in this field, with emphasis on a systems-oriented rationale and perspective. As such, the article is an important stage in building this body of knowledge, and towards the conceptualization of key variables used in global quality management, from a systems approach that interacts with the fields of international management and strategic management.

The 5-hydroxymethylfurfural (HMF) is a six-carbon heterocyclic organic compound with two substituents an aldehyde group and an alcohol group. It is formed from saccharides as a result of two reactions: the Maillard reaction and the caramelization of saccharides. It has both a negative and a positive effect on the human body, which makes it, even more, an attractive research object. The objective of the study was to determine HMF content in honey samples available on the Polish market using three varied methods and compare the results obtained. The methodology used included: two spectrophotometric methods (by White and Winkler) and the HMF determination method based on the LC-MS/MS technique developed uniquely for this study. The determined HMF content in all tested honey samples did not exceed the applicable standard. All results are within the scope of the European Council Directive 2001/110/EC of 20 December 2001, i.e. they do not exceed HMF content in honey, which is 40 mg/kg.

The most relevant fungal disease of the olive tree in Portugal is anthracnose, which has negative effects on fruit destruction and consequently on the yield and quality of the olive oil. Moreover, the loss of quality caused by olive fruit fly is associated with the presence of fungi in the galleries made by the larvae. The present study focuses on the effect of olive anthracnose and olive fly on the content of bioactive compounds, namely on hydroxytyrosol (HYT) and its derivatives (health claim) in olive oils extracted from 'Galega Vulgar' and 'Cobrançosa' cultivars. The olives, with different damage levels (olive fly and anthracnose disease), were harvested in Castelo Branco (Center of Portugal) in organic rainfed orchards, at four harvest times during 2019, 2020 and 2021 harvest years. The fruits were immediately submitted to olive oil extraction. The results of the quality criteria show that Galega olive oils extracted from olives with a higher anthracnose incidence show no conformity for the Extra Virgin Olive Oil (EVOO) and Virgin Olive Oil (VOO) categories, with high acidity values and negative sensory notes accompanied by the disappearance of oleacein (the main phenolic compound of both monovarietal olive oils). Conversely, no sensory defects were observed in Cobrançosa olive oils extracted from fruit with high anthracnose and olive fly incidence. Moreover, despite a decrease in all the positive attributes associated with the cultivar, namely in oleacein and oleocanthal contents, quality criteria were still in accordance with the EVOO category. The total HYT and tyrosol (TYR) content (> 5 mg/20g) allows the use of the health claim on the label of all the analysed Cobrançosa olive oils.

Quality of life (QoL) assessments are integral to cancer care, yet their effectiveness in providing essential information for supporting survivors varies. This study aimed to elucidate key indicators of QoL among colorectal cancer survivors from the perspective of healthcare professionals, and to evaluate existing QoL questionnaires in relation to these indicators. Two studies were conducted: a Delphi study to identify key QoL indicators and a scoping review of questionnaires suitable for colorectal cancer survivors. Fifty-four healthcare professionals participated in the Delphi study's first round, with 25 in the second. The study identified two primary QoL domains (Physical and Psychological) and 17 subdomains deemed most critical. Additionally, a review of 12 questionnaires revealed two instruments assessing the most important general domains. Findings underscored a misalignment between existing assessment tools and healthcare professionals' clinical priorities in working with colorectal cancer survivors. To enhance support for survivors' QoL, efforts are needed to develop instruments that better align with the demands of routine QoL assessment in clinical practice.

(1) Background: Grapes and their associated by-products (as grape pomace, GP) stand out for their polyphenol content, which makes them a source of bioactive compounds with antioxidant capacity. The aim of this research was to determine if the inclusion of 50 g/kg of GP in the diet of hens could enrich egg with antioxidants and to study its effect on internal and external egg quality parameters. (2) Methods: A trial was conducted with two genetic lines of hens, which were fed either a control diet or a diet containing 50 g/kg of GP. Performance, internal and external egg quality, and egg yolk content of vitamins E and A, and gallic acid were determined; (3) Results: In eggs laid by hens fed GP diet, Haugh units and yolk colour score were enhanced, and eggshell became thinner, but without affecting the breaking strength. No dietary effect was observed on vitamin contents in yolk. Higher gallic acid content was observed in yolk of eggs laid by hens fed the GP diet, suggesting that some dietary phenolic compounds could be transferred to the eggs. Hen genetics influenced egg weight, albumen Haugh units, shell thickness and α- and γ-tocopherol concentration in yolks; (4) Conclusions: Dietary inclusion of GP improved the internal quality of eggs, enriching yolks with a phenolic compound, but reduced shell thickness.

The aim of the study was to test the significance of the EPT index in the water quality assessment of three types of water bodies in hilly and mountainous region of Serbia. The aquatic macroinvertebrate community was dominated by the group of insects, of which 95 taxa represent the EPT group. We compared the obtained values of biological indices used for the assessment of water quality according to the national legislation with the overall status assessment represented by the ecological quality classes (EQC). The results of the Spearman correlation test showed a negative correlation of EQC with the EPT index, BMWP score, H', total number of taxa and number of sensitive taxa, while a positive correlation was observed for the values of SI and Tubificinae %. The values of EQC and biological indices were subjected to principal component analysis (PCA). The results showed that the parameters that contributed most to the differences were the EPT index, the BMWP score and the number of sensitive taxa. The results indicate that the EPT index is an excellent indicator of changes in water quality and an important tool for the ecological categorization of water bodies in mountain regions.

In this communication the concept of functional materials is understood such as real modified substrates for nanomedicine applications. Functional and modified substrates focused on microcapsules and devices for new nanomedicine diagnosis and treatments. Cases of different materials are shown to support the functionality strategy, as in particular chemicals, pharmacophores, and controlled nano-chemistry for the design of nanoplatforms. Recent studies have reported hybrid inorganic/organic compositions for biocompatible, biodegradable, and support materials added to particular physical properties such as conductive, semiconductive, and high electromagnetic fields from the near field within the nanoscale to far-field applications and new nano-pharmacophores and nanomedicine therapeutics. New approaches are shown from the nano-scale to the micro- and higher sizes of substrates for improved therapeutic strategies. Micro-capsules for biosensing and drug delivery applications were developed. In addition, we report recent and novel research centered on implantable, portable, and wearable devices applied to future treatments.

Biodiversity conservation questions human practices towards biodiversity and, therefore, largely conflicts with ordinary societal aspirations. Decisions on the location of protected areas, one of the most convincing conservation tools, reflect such a competitive endeavor. Operations Research (OR) brings a set of analytical models and tools capable of resolving the conflicting interests between ecology and economy. Recent technological advances have boosted the size and variety of data available to planners, thus challenging conventional approaches bounded on optimized solutions. New models and methods are requested to use such a massive amount of data in integrative schemes addressing a large variety of concerns. Here, we provide an overview on the past, present and future challenges that characterize spatial conservation models supported by OR. By enlarging the spatial, temporal, taxonomic and societal horizons of biodiversity conservation planners navigate around multiple bio-socioeconomic equilibria and are able to decide on cost-effective strategies to improve biodiversity persistence.

Analytics have become increasingly popular among sports in recent years, providing valuable information regarding physical and mental health. Many athletes have found that analytics during training can help to improve their performance, reduce the risk of injury, and enhance their overall well-being. This paper aims to improve the results of handball players by applying a method for measuring the influence of different trials on aggregate performance calculated per each athlete in order to qualify for the Olympic Games. By separating the isolated action of each trial, the result is an additional influence caused by the interaction of factors or the simultaneous action. That might explain why the neuromuscular feedback loop is utterly necessary to perform handball motor actions. Further on, the ML analysis can help identify areas for improvement, optimize training programs, and enhance overall team performance.

Background Total serum bile acids (TSBA), liver-spleen scan and dynamic liver functional tests, in our case the antipyrine clearance (Ap Cl), have been long adopted. The aim of our study was that of assessing whether some diagnostic tests, scarcely performed due to the novel techniques implementation, were reliable diagnostic tools. Methods Data extracted from records of two well-matched for age and gender populations was retrospectively analysed. Specifically, 17 patients with biopsy-proven chronic hepatitis were confronted with 17 subjects suffering from liver cirrhosis. Clinical, laboratory and instrumental findings, such as the Child-Pugh classification, the number connection test for evaluating hepatic encephalopathy, prothrombin time, serum albumin levels, TSBA concentration, Ap Cl determination, abdominal ultrasound and liver-spleen scan imaging as well as endoscopy features were evaluated. Results Cirrhotics showed a median concentration of TSBA increased respect to that of patients with chronic hepatitis, independently from gender, 20.1 versus 12.24 micromol/L, P= 0.0054. The median AP Cl value of the patients with liver cirrhosis was reduced confronted with that of patients with chronic hepatitis, specifically, 13.92 opposed to 18.3 mcg Ap/dL, P= 0.045. Furthermore, the median liver-spleen scan score was higher in cirrhotics than in chronic hepatitis patients, i.e., 3.47 versus 1.47, P= 0.000. The AUROCs of TSBA levels and of the liver-spleen scan scores for differentiating patients with liver cirrhosis from those with chronic hepatitis were 0.82 and 0.96, respectively. When was applied a new predictive model, combining the previous ones, the AUROC to discriminate patients belonging to the two populations was 0.98. The best cut-off of the new index was 26, with a sensitivity and specificity of 100.00% and 82.35%, respectively, correctly classifying 91.18% of the patients. Discussion Both TSBA and liver-spleen scan were high discriminant as well as their combination, while Ap Cl showed some limitations as reliable diagnostic tool. TSBA and liver-spleen scan have been too soon and unnecessarily overlooked.

If one considers chemical-biology toolsets that have had the greatest impact on numerous fields of life sciences over the most recent years, proximity-labeling tools, such as APEX, and Bio-ID arguably lead the way. This article reflects upon the current state-of-the-art and discusses key limitations underlying these emerging approaches, in particular, the limited functional knowledge they provide in understanding local proteomes / interactomes. This limitation is directly linked to the use of non-biologically- or non-pharmaceutically-relevant reactive intermediates in the course of covalently labeling the local proteomes. As such, these methods cannot report on specific functions of localized protein players, nor can they scrutinize whether the specific functions of such proteins/interactomes can be directly manipulated by pharmacologically-relevant small-molecule ligands. The latest data hint that precision localized electrophile delivery concept ushers a means to address this limitation with high spatiotemporal resolution, and ultimately, in relevant live animals.

Zoos are increasingly putting in place formalized animal welfare assessment programs to allow monitoring of welfare over time, as well as to aid in resource prioritization. These programs tend to rely on assessment tools that incorporate resource-based and observational animal- focused measures since it is rarely feasible to obtain measures of physiology in zoo-housed animals. A range of assessment tools are available which commonly have a basis in the Five Domains framework. A comprehensive review of the literature was conducted to bring together recent studies examining welfare assessment methods in zoo animals. A summary of these methods is provided with advantages and limitations of the approach es presented. We then highlight practical considerations with respect to implementation of these tools into practice, for example scoring schemes, weighting of criteria, and innate animal factors for consideration. It is concluded that would be value in standardizing guidelines for development of welfare assessment tools since zoo accreditation bodies rarely prescribe these. There is also a need to develop taxon or species- specific assessment tools to inform welfare management.