Accurate power curve modelling is essential to continuously evaluate the performance of a wind turbine (WT). In this work, we characterize the wind power curves using SCADA data acquired at a frequency of 5 minutes in a wind farm (WF) consisting of 5 WTs. Regarding the non-parametric methods, we select artificial neural networks (ANNs) to make curve estimations. Given that, we have the curves provided by the manufacturer of the WTs given by some very precisely measured pair of wind speed and power points. We can evaluate the difference between the manufacturer characterization and the ones estimated with the data provided by the SCADA system. Before the estimation, we propose a method of filtering the anomalies based on the characteristics provided by the manufacturer. We use three-quarters of the available data for curve estimation and one-quarter for the test. One WT suffered a break in the test part, so we can check how the test estimates reflect this problem in its wind-power curve compared to the estimations obtained in the WTs that worked adequately.

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

In order to correct attenuated millimeter-wavelength (Ka-band) radar data and address the problem of instability, an attenuation correction methodology (attenuation correction with variation trend constraint; VTC) was developed. Using synchronous observation conditions and multi-band radars, the VTC method adopts the variation trends of reflectivity in X-band radar data captured with wavelet transform as a constraint to adjust reflectivity factors of millimeter-wavelength radar. The correction was evaluated by comparing reflectivities obtained by millimeter-wavelength cloud radar and X-band weather radar. Experiments showed that attenuation was a major contributory factor in the different reflectivities of the two radars when relatively intense echoes exist, and the attenuation correction developed in this study significantly improved data quality for millimeter-wavelength radar. Reflectivity differences between the two radars were reduced and reflectivity correlations were enhanced. Errors caused by attenuation were eliminated, while variation details in the reflectivity factors were retained. The VTC method is superior to the bin-by-bin method in terms of correction amplitude and can be used for attenuation correction of shorter wavelength radar assisted by longer wavelength radar data.

Salt stress is a major limiting factor for alfalfa yield due to its relatively low salt tolerance. High soil salinity adversely impacts alfalfa growth and development, leading to reduced yield. Melatonin (MT) is known to play a significant role in enhancing plant resistance to abiotic stresses. However, the mechanisms underlying melatonin-mediated abiotic stress responses, particularly salt stress, are not well understood. To address this gap, we conducted a study focusing on germinating alfalfa seeds under salt stress. Physiological indexes and transcriptomics analyses were carried out on the germinated seeds to investigate the effects of melatonin on alfalfa seedlings under salt stress conditions. Our results revealed that the application of melatonin led to an increase in shoot length and fresh weight of alfalfa seedlings under salt stress. Moreover, key physiological indexes such as peroxidase (POD) activity and glutathione (GSH) content were enhanced, while levels of malondialdehyde and superoxide anions decreased. Transcriptomic analysis identified a total of 2,131 differentially expressed genes in the salt-treated group, with 726 up-regulated and 1,405 down-regulated genes, while the MT-treated group showed 2896 differentially expressed genes, of which 1,097 were up-regulated and 1,799 were down-regulated. Further, KEGG enrichment analysis highlighted the enrichment of differentially expressed genes in pathways including flavonoid biosynthesis, ABC transporter, glutathione metabolism, and the MAPK signaling pathway, with these pathways more significantly enriched in the MT-treated group. These findings collectively suggest that melatonin plays a crucial role in alfalfa's response to salt stress and offer new insights into the genomic mechanisms underlying melatonin-mediated salt tolerance in alfalfa.

The key links of face recognition are digital image preprocessing, facial feature extraction and pattern recognition, this article aimed at the current problem of slow speed and low recognition accuracy of face recognition , from the above three key links, on the basic of analyzing the therories of Fractional Differential Masks Operator (FDMO), Principal Component Analysis (PCA) and Support Vector Machine (SVM), design a kind of FDMO+PVA+SVM coupling algorithm that applies to face recognition to improve the speed and accuracy of it. To realize FDMO+PCA+SVM coupling algorithm, first, we should apply FDMO to face image processing binary marginalization, the purpose is getting face contour; Then, we apply PCA to get the feature of face image which is disposed by binary marainalization. At last, we can apply One-Against All of the SVM classifier and LibSVM software package to realize face recognition. Beside, the article with nine different coupling algorithm design four groups of experimental reaults on the ORL face database verified by comparative analysic FDMO+PCA+SVM coupling algorithm in the superiority of face recognition accuracy and speed.

Salt stress is one of the major abiotic stresses that lead to crop yield reduction worldwide. Melatonin (MT), an endogenous hormone synthesized in plants, plays an important role in responding to abiotic stimuli such as drought, salinity, heat, cold, etc. However, the molecular mechanisms of MT-mediated abiotic stresses remain to be better understood. In order to explore the key genes and pathways of melatonin in alleviating salt stress, physiological and biochemical indicators as well as transcriptomics profile were conducted in alfalfa seedlings. The results showed that the germination rate, bud length and fresh weight of alfalfa seedlings added with melatonin were higher than those treated with salt alone. In addition, Malondialdehyde (MDA) and Superoxide anion (O2-) contents also displayed a decreasing trend. The activity and content of Superoxide dismutase (SOD)、peroxidase (POD) and Glutathione (GSH) increased to varying degrees. In order to further reveal the molecular mechanism of MT-mediated salt tolerance of alfalfa, transcriptome analysis was performed on alfalfa seedlings. 2,181 differentially expressed genes (DEGs) were obtained in the salt-treated group, including 780 upregulated genes and 1,401 down-regulated genes, while 4,422 DEGs were obtained in the MT group, among which 1,438 were upregulated and 2,984 were downregulated. By using GO functional annotation and KEGG pathway enrichment, we found that DEGs were mainly enriched in the biosynthesis of flavonoids, isoflavones, plant hormones, Glutathione (GSH), soluble sugars and other substances, as well as in the ABC transporter and MAPK signaling pathways. Among them, the DEGs in the MT group was more enriched in these pathways, suggesting that MT can combat salt stress by regulating the expression of genes related to phytohormone and antioxidant capacity, which has important reference value for the breeding of salt-tolerant alfalfa and other crops.

Over the past couple of decades, Global positioning system (GPS) technology has been utilized to collect large-scale data from travel surveys. As the precise spatiotemporal characteristics of travel could be provided by GPS devices, the issues of traditional travel survey, such as misreporting and non-response, could be addressed. Considering the defects of dedicated GPS devices (e.g., need much money to buy devices, forget to take devices to collect data, limit the simple size because of the number of devices, etc.), and the phenomenon that the smartphone is becoming one of necessities of life, there is a great chance for the smartphone to replace dedicated GPS devices. Although, several general reviews have been done about smartphone-based GPS travel survey in the literature review section in some articles, a systematic review from smartphone-based GPS data collection to travel mode detection has none. The included studies were searched from six databases. The purpose of this review is to critically assess the current literature on the existing methodologies of travel mode detection based on GPS raw data collected by smartphones. Meanwhile, according to the systematic comparison among different methods from data-preprocessing to travel mode detection, this paper could carefully provide the Strengths and Weaknesses of existing methods. Furthermore, it is the crucial step to develop the methodologies and applications of GPS raw data collected by smartphones.

A low-cost bio-mass-derived carbon substrate has been employed to synthesize MoS₂@carbon composites through a hydrothermal method. Carbon fibers derived from natural cotton provide a three-dimensional and open framework for the uniform growth of MoS₂ nanosheets, thus constructing hierarchically coaxial architecture. The unique structure could synergistically benefit fast Li-ion and electron transport from the conductive carbon scaffold and porous MoS₂ nanostructures. As a result, the MoS₂@carbon composites, when served as anodes for Li-ion batteries, exhibit a high reversible specific capacity of 820 mAh g^-1, high-rate capability (457 mAh g^-1 at 2 A g^-1), and excellent cycling stability. The superior electrochemical performance makes the MoS₂@carbon composites to be low-cost and promising anode materials for Li-ion batteries.

In this study, we successfully synthesized a novel branched polyamide 6 with ε-caprolactam(CPL) and α-Amino-ε-caprolactam(ACL) through hydrolytic ring-open co-polymerization. The NMR characterization and rheological test result proved the existence of branched chain structure additionally. The branched chain structure caused a remarkable enhancement in the rheological properties. The met index(MFR),zero shear rate viscosity and storage modulus at low frequency region had a remarkable increase.The shear thinning phenomenon became more obvious. The thermal properties test determined by differential scanning calorimetry(DSC) showed that the melting point and crystallinity of co-polymers decreased with the increase of ACL addition.However, the crystal structure of the samples remained unchanged. The appropriate addition amount of ACL can improve the tensile mechanical properties of the co-polymers. When the amount of ACL was 1%, the tensile strength and fracture elongation rate of the co-polymers had the most significant increase.

In this paper, we first discuss the research status and application progress of the finite element method and the smoothed particle method. By analyzing the advantages of the smoothed particle method and the finite element method, a new coupling algorithm, namely FEM-SPH algorithm, is proposed. By the method of comparison, it shows that finite element method and SPH method in the simulation of large deformation problems each have advantages and disadvantages, the finite element method smoothed particle coupling algorithm is effective to achieve the performance of high computational efficiency and can naturally simulate large deformation problems across. In the process of calculation, the large deformation unit can be freely into an algorithm to facilitate the calculation accuracy and efficiency of three methods of numerical simulation. Through the study found, FEM-SPH algorithm not only overcome the defect of smooth particle tensile instability, but also overcomes the problem of low efficiency of finite element computation. To further test the FEM-SPH algorithm has advantages in the practical engineering, we have carried out the actual test to the example of the super high speed collision, concluded that, since the target of most of the computational domain is always finite element, smoothed particle focused only in contact with the projectile and target of local area, particle number is not much, the whole calculation process just ten minutes, computational efficiency has been greatly improved, at the same time in the simulation of large deformation, the advantage is very obvious .This provides a criterion for the actual project, depending on the specific material deformation mode and choose a more appropriate conversion algorithm.

Three-dimensional V₂O₅ hollow structures have been prepared through a simple synthesis strategy combining solvothermal treatment and a subsequent thermal annealing. The V₂O₅ materials are composed of microspheres 2–3 μm in diameter and with a distinct hollow interior. The as-synthesized V₂O₅ hollow microspheres, when evaluated as a cathode material for lithium-ion batteries, can deliver a specific capacity as high as 273 mAh·g⁻¹ at 0.2 C. Benefiting from the hollow structures that afford fast electrolyte transport and volume accommodation, the V₂O₅ cathode also exhibits a superior rate capability and excellent cycling stability. The good Li-ion storage performance demonstrates the great potential of this unique V₂O₅ hollow material as a high-performance cathode for lithium-ion batteries.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

MIMO (multiple-input multiple-output) radar provides much more flexibility than the traditional radar for its ability to realize far more observation channels than the actual number of T/R (transmit and receive) elements. Designing the array of MIMO imaging radar, the commonly used virtual array theory generally assumes that all elements are placed on the same line. However, due to the physical size of the antennas and coupling effect between T/R elements, a certain height difference between T/R arrays is essential, resulting in the defocusing of edge points of the scene. On the other hand, the virtual array theory implies far-field approximation, leading to inevitable high grating lobes in the imaging result of near-field edge points of the scene observed by common MIMO array. To tackle these problems, this paper derives the relationship between target’s PSF (point spread function) and pattern of T/R arrays, by which the design criterion of near-field imaging MIMO array is presented. Firstly, the proper height between T/R arrays is designed to focus the near-field edge points well. Secondly, the far-field array is modified to suppress the grating lobes in the near-field area. Finally, the validity of the proposed methods is verified by simulations and an experiment.

Timely and accurate information on tree species is crucial for the sustainable management of natural resources, forest inventory, biodiversity detection, and carbon stock calculation. The advancement of remote sensing technology and artificial intelligence has facilitated the acquisition and analysis of remote sensing data, resulting in more precise and effective classification of tree species. Multimodal remote sensing data and deep learning seem to be the current tree species classification research mainstream, whether or not. The current review on the remote sensing data and deep learning tree species classification methods perspectives to analyze the unimodal and multimodal remote sensing data and classification methods in this realm is missing. To bridge the gap, we search for major trends in the remote sensing data and tree species classification methods, provide a detailed overview of classic deep learning-based methods for tree species classification, and discuss the limitations.

Accurate diagnosis for the 400 million people with rare diseases is critical for healthcare decisions, prognosis, understanding disease mechanisms, and identification of treatments. Despite advances in genome sequencing, barriers such as high interpretation costs, diagnostic expertise, throughput associated delays, and uncertain variant classifications persist, with demand exceeding capacity. Many variant classification methods focus narrowly on specific consequences, leading to the use of complex integrative pipelines that often overlook transcript variability and lack prediction transparency. To overcome these limitations, we introduce DITTO. This transparent, transcript-aware machine-learning method demonstrates superior overall performance in accuracy, recall, and precision when compared to existing tools. DITTO is publicly available at https://github.com/uab-cgds-worthey/DITTO

Gene regulation is vital for cellular function and homeostasis, involving diverse mechanisms controlling specific gene products and contributing to tissue-specific gene expression. Dysregulation leads to diseases, emphasizing the need for understanding these mechanisms. Non-coding regions, notably enhancers and super-enhancers (SEs), act as crucial gene regulators, orchestrating transcriptional activity via transcription factors (TFs). SEs, with high activity, are pivotal in cell identity and disease progression. Current computational approaches focus on individual regulators like TFs and miRNAs, neglecting SE interactions. We emphasize incorporating SEs into models to enhance understanding. Experimental studies have recently linked miRNAs and TFs to SEs. Chromatin immunoprecipitation followed by sequencing (ChIP-Seq) provides valuable SE information. In this review, we categorize computational methods leveraging TF and miRNA data into three areas and explore challenges integrating enhancers/SEs. These include unraveling indirect regulatory networks, identifying network motifs, and enriching pathway identification by dissecting gene regulators, including SEs. We hypothesize that addressing these challenges will enhance our understanding of gene regulation, aiding in identifying therapeutic targets and disease biomarkers. We believe that understanding the role of ChIP-Seq data in predicting the effect of miRNA on gene regulation is crucial to construct statistical/computational model that would tackle these challenges.

Proteomics research has become one of the most important topics in the fields of life science and natural science. At present, research on protein–protein interaction networks (PPINs) mainly focuses on detecting protein complexes or function modules. However, existing approaches are either ineffective or incomplete. In this paper, we investigate function module detection mechanisms in PPIN, including open databases, existing detection algorithms and recent solutions. After that, we describe the proposed solution based on simplified swarm optimization (SSO) algorithm and gene ontology knowledge. The proposed solution implements SSO algorithm for clustering proteins with similar function, and imports biological gene ontology knowledge for further identifying function complexes and improving detection accuracy. Furthermore, we use four different categories of species dataset for experiment: Fruitfly, Mouse, Scere, and Human. The testing and analysis result show that the proposed solution is feasible, efficient and could achieve a higher accuracy of prediction than existing approaches.

Modern scientific research particularly radio astronomi- cal spectroscopic observations cannot be imagined without appropriate software suite. That is necessary because of two reasons 1) data are in digital form and 2) data processing is a complex multi-step process. In this paper created in VIRAC data processing suite for a single radio telescope, space maser observations are presented. Software Defined Radio (SDR) backend data processing is described. Implementation of the frequency switching algorithm, acquisition of observation data and their format for storing are discussed. Multiple ways to display the observation results are highlighted.

Green manure could improve soil nutrients and crop production, playing a significant role in sustainable agriculture. However, the impacts of green manure on crop health and the roles soil microbial communities play in the process haven’t been clarified clearly yet. In this study, we investigated soil microbial community composition and structure in four tobacco farmlands, which were treated with different green manure (control, ryegrass, pea and rape), using 16S rRNA gene amplicons sequencing. Results showed that green manure had significant impacts on soil properties, microbial communities and tobacco health. First, soil total C, N and Ca content increased significantly in groups treated with green manure than control. Second, soil community diversity was significantly higher in groups treated with green manure. Third, green manure especially ryegrass, decreased tobacco disease (bacterial wilt) rate dramatically, and the process might be mediated by soil microbial communities. On the one hand, several microbial populations were found to be potentially disease inducible or suppressive. For example, the abundances of Dokdonella and Rhodanobacter were positively correlated to tobacco disease rate, while Acidobacteira_Gp4 and Gp6 had negative correlations with tobacco disease. On the other hand, soil microbial communities were shaped by soil properties (e.g., pH, C and N content). In conclusion, our research showed that green manure could increase soil nutrients directly, and further improve tobacco health mediated by soil microorganisms, which may shed light on revealing interactions among soil properties, microorganisms and plants.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

Despite the development of technologies, modern methods of disposal of end-of-life tires most often represent either the incineration in cement kilns or the destruction of tires in special landfills, showing a lack of sustainable recycling of this valuable material. The fundamental role of recycling is evident, and the development of high-efficiency processes represents a priority for the European market. Therefore, investigation of end-of-life rubber processing methods is of high importance for manufacturers and recyclers of rubber materials. In this paper, methods of processing of end-of-life tires are reviewed in order to obtain rubber crumb, which can later be used in the production of new industrial rubber goods and composite The processes of separation end-of-life tire into fractions by type of materials using mechanical processing methods along with mechanochemical and mechanical processes of processing the materials of used tires in order to obtain crumb rubber of various fractions and chemical reactivity are considered.

Intrinsically Disordered Proteins (IDPs) play crucial roles in signal transduction, cell differentiation, and transcriptional regulation. Many disrupted genes associated with mental disorders are identified as IDPs, and emerging evidence suggests the functional role of IDPs in neuropsychiatric disorders. However, few studies comprehensively explore the functional association between protein disorder properties and different mental diseases. To address this gap, we collected disrupted gene sets for seven mental diseases (MDD, SCZ, BP, ID, AD, ADHD, ASD) and a control gene set from normal brains using DisGeNET and GeneCards databases. The state-of-the-art predictor IUPred2A was then utilized to calculate the disorder properties , followed by a thorough comparison between the disordered proteins in mental diseases and healthy controls. Functional enrichment analysis and protein-protein interaction networks were conducted to investigate the IDPs’ functional roles in psychiatric diseases. Additionally, we demonstrated the role of IDPs in protein binding formations through a case study of alpha-synuclein using protein docking. Our findings reveal that differentially expressed proteins in mental disorders, especially in ASD and ADHD, exhibit more IDPs than those in healthy controls. IDPs in psychiatric disorders are significantly enriched in neurodevelopmental pathways and play an important role in in gene expression regulation. Our results indicate distinct functional patterns of disorder proteins among mental diseases and healthy controls. When comparing the IDPs between ASD and ADHD, we observed that IDPs in ADHD are more likely linked to the synaptic signaling and regulation, while IDPs in ASD are more tendentiously related to diverse and complex biological processes. Our work offers valuable insights into the important functions of IDPs in psychiatric disorders, enhancing our understanding of the molecular mechanisms involved in psychiatric disorders.

The traditional practice of harvesting and processing raw date palm sap is not only culturally significant but also an essential nutritional source in South Asia. Yet, the potential for bacterial or viral contamination from animals and environmental sources during its collection remains a real and insufficiently studied risk. Implementing improved food safety measures and collection techniques could mitigate the risk of these infections. Additionally, the adoption of advanced food analytical methods has the potential to identify pathogens and uncover the natural bacterial diversity of these products. The advancement of NGS technologies, particularly nanopore sequencing, offers rapid and highly mobile capabilities. In this study, we employed nanopore sequencing for bacterial metabarcoding of a set of raw date palm sap samples collected without protective coverage against animals in Bangladesh in 2021. We identified several bacterial species with importance in the natural fermentation of the product and demonstrated the feasibility of this NGS method in the surveillance of raw palm sap products. We revealed two fermentation directions dominated by either Leuconostoc species or Lactococcus species in these products at the first 6 hours from harvest along with opportunistic human pathogens in the background, represented with low abundance. Plant pathogens, bacteria with the potential for opportunistic human infections and the sequences of the Exiguobacterium genus were also described and their potential role is discussed.

Knowledge processing is an important feature of intelligence in general and artificial intelligence in particular. To develop computing systems working with knowledge, it is necessary to elaborate means of working with knowledge representations (as opposed to data) because knowledge is an abstract structure. There are different forms of knowledge representations derived from data. One of the basic forms is called a schema. The goal of this paper is the development of theoretical and practical tools for processing schemas. To achieve this goal, we use schema representations elaborated in the mathematical theory of schemas and use structural machine as a powerful theoretical tool for modeling parallel and concurrent computational processes. We describe the schema of autopoietic machines as physical realizations of structural machines. An autopoietic Machine is a technical system capable of regenerating, reproducing and maintaining itself by production, transformation and destruction of its components and the networks of processes downstream contained in them. We present the theory and practice of designing and implementing autopoietic machines as information processing structures integrating both symbolic computing and neural networks. Autopoietic machines use knowledge structures containing the behavioral evolution of the system and its interactions with the environment to maintain stability by counteracting fluctuations.

To live in the information society means to be surrounded by billions of electronic devices full of sensors that constantly acquire data. This enormous amount of data must be processed and classified. A solution commonly adopted is to send these data to server farms to be remotely elaborated. The drawback is a huge battery drain due to high amount of information that must be exchanged. To compensate this problem data must be processed locally, near the sensor itself. But this solution requires huge computational capabilities. While microprocessors, even mobile ones, nowadays have enough computational power, their performance are severely limited by the Memory Wall problem. Memories are too slow, so microprocessors cannot fetch enough data from them, greatly limiting their performance. A solution is the Processing-In-Memory (PIM) approach. New memories are designed that are able to elaborate data inside them eliminating the Memory Wall problem. In this work we present an example of such system, using as a case of study the Bitmap Indexing algorithm. Such algorithm is used to classify data coming from many sources in parallel. We propose an hardware accelerator designed around the Processing-In-Memory approach, that is capable of implementing this algorithm and that can also be reconfigured to do other tasks or to work as standard memory. The architecture has been synthesized using CMOS technology. The results that we have obtained highlights that, not only it is possible to process and classify huge amount of data locally, but also that it is possible to obtain this result with a very low power consumption.

Precise monitoring of individual crop growth and health status is crucial for precision agriculture practices. However, traditional manual inspection methods are time-consuming, labor-intensive, and often lack the spatial resolution required for detailed analysis. This research addresses the need for efficient and high-resolution crop monitoring by leveraging Unmanned Aerial Vehicle (UAV) imagery and advanced computational techniques. The primary objective was to develop a methodology for precise identification, extraction, and monitoring of individual corn crops throughout their growth cycle. This was achieved by integrating UAV-derived data with image processing, computational geometry, and machine learning techniques. UAV imagery was ac-quired bi-weekly at altitudes of 40m and 70m, capturing the entire growth cycle of a corn crop from planting to harvest. A time-series Canopy Height Model (CHM) was generated by analyzing the differences between the Digital Terrain Model (DTM) and the Digital Surface Model (DSM) derived from the UAV data. Local spatial analysis and image processing techniques were em-ployed to determine the local maximum height of each crop. Subsequently, a Voronoi data model was developed to delineate individual crop canopies, successfully identifying 13,000 out of 13,050 corn crops in the study area. For enhanced accuracy in canopy size delineation, vegetation indices were incorporated into the Voronoi model segmentation, refining the initial canopy area esti-mates by eliminating interference from soil and shadows. The proposed methodology enables precise estimation and monitoring of crop canopy size, height, biomass reduction, lodging, and stunted growth over time, providing valuable insights for precision agriculture practices. This work contributes to the scientific community by demonstrating the potential of integrating UAV technology, computational geometry, and machine learning for accurate and efficient crop mon-itoring at the individual plant level.

Kamchatka berries (Lonicera caerulea L.) are known for their high content of phenolic compounds or vitamins, which is reflected in their antibacterial, detoxifying and anti-inflammatory properties. They are used in the production of jams, juices, wines and as natural dye. A bioferment was prepared from the pomace of the Kamchatka berry varieties Aurora and Indigo Gem and the strains Saccharomyces cerevisiae and Lacticaseibacillus paracasei, which was used to prepare a cosmetic preparation with a concentration of 5% in accordance with the guidelines of the COSMOS certification body. Conducted physico-chemical and organoleptic analyses and bioactive profile characterisation (UHPLC-DAD and UHPLC-ESI-MS/MS). The results showed that the presence of caffeic acid 4.47 ± 0.07 mg/100g was detected after fermentation of Kamchatka berry pomace. Vitamin C content increased by 141% after fermentation of Kamchatka berry pomace. The results of stability tests showed that in the process of physicochemical analysis of cosmetic preparation with bioferment of Kamchatka berry pomace the pH should oscillate in the range of 4.38-4.76 ± 0.01. Stability tests showed that the cosmetic should be protected from high temperatures and UV radiation and proved that the product is stable under changing conditions, resulting in lower transport and storage costs.

A new Mg-Zn-Zr-Ca alloy in powder state was obtained via mechanical alloying method, from pure elemental powder. Further, the obtained powder-alloy was processed by selective laser melting (SLM) procedure to obtain 3D printed samples for small biodegradable implants. A series of microstructural, mechanical and corrosion analysis were performed. The SEM analysis of powder-alloy reveal a good dimensional homogeneity, with uniform colored, no agglutinated and almost rounded particles, suitable for selective laser melting procedure. Further, the SLM samples reveal a robust and unbreakable morphology, with a suitable porosity and without undesirable balling effect. The tested Young’s modulus of the SLM samples, of 42 GPa, is close to cortical bone one, of 30 GPa. The corrosion tests performed in PBS (Phosphate-buffered saline) solution show that the corrosion parameters have a satisfactory evolution.

Transportation systems through the ages have seen drastic evolutions in terms of transportation methods, speed of transport, infrastructure, technology, connectivity, influence on the environment, and accessibility. The massive transformation seen in the transportation sector has been fueled by the industrial revolutions which have continued expansion and progress into the fourth industrial revolution. However, the methodologies of data collection and processing used by the many drivers of this progress differ. The significance of standardized data and its mode of collection cannot be overstated as it has a major impact on the process outcomes. In order to achieve a better understanding of the impact of this, this study methodically reviewed the literature on the subject of the data collection and processing mechanism of 4IR technologies in the context of the transport industry with an emphasis on the areas of accomplishment of several studies and drawing attention to their limitations. Although the industry has advanced significantly as a result of the adoption and application of various research studies in this field, considerable focus needs to be placed in the areas of standardized data collection and computational approaches, which will ultimately assist in achieving various benefits in the transportation industry.

In ref. [1], we pointed out that certain anomalies observed in the published data for ac magnetic susceptibility of a room temperature superconductor reported in Nature 586, 373 (2020) [2] would be cleared up once the measured raw data were made available. Part of the measured raw data were recently posted in arXiv:2111.15017 [3]. Here we report the results of our analysis of these raw data and our conclusion that they are incompatible with the published data. Implications of these results to the claim that the material is a room temperature superconductor are discussed.

Next-generation sequencing is now a mature technology, allowing partial animal genomes to be produced for many clades. Though many software exist for genome assembly and annotation, a simple pipeline that allows researchers to input raw sequencing reads in fastq format and allow the retrieval of a completely assembled and annotated mitochondrial genome is still missing. mitoMaker 1.0 is a pipeline developed in python that implements (i) recursive de novo assembly of mitochondrial genomes using a set of increasing k-mers; (ii) search for the best matching result to a target mitogenome and; (iii) performs iterative reference-based strategies to optimize the assembly. After (iv) checking for circularization and (v) positioning tRNA-Phe at the beginning, (vi) geneChecker.py module performs a complete annotation of the mitochondrial genome and provides a GenBank formatted file as output.

Aflatoxin M1 (AFM1), a carcinogenic toxin, mainly contaminates cow milk and poses significant challenges to the dairy industry and, thereby, public health in most tropical countries, including Ethiopia. This study aimed to investigate the prevalence and level of AFM1 in raw cow milk collected from Specialized Dairy Farms and Milk Vendors in three Urban Centers: Chiro town, Dire Dawa, and Harar cities in Eastern Ethiopia. 180 milk samples were collected from two major Milk Sources: Specialized Dairy Farms (N=90) and Milk Vendors (N=90) using a simple random sampling technique. AFM1 was analyzed using high-performance liquid chromatography. The study revealed that, 63.9% (115/810) prevalence and 0.179±0.48µg/L mean of AFM1 level in milk, which 39.13% and 26.08% exceed the tolerable limits of EU and FDA respectively. A 40.0% prevalence and 0.344±0.72µg/L average of AFM1 in the milk from Dire Dawa city was significantly higher than the samples from other Urban Centers. However, 30.43% and 29.57% prevalence as well as 0.055±±0.13µg/L and 0.140±0.33µg/L average of AFM1 in milk from Chiro town and Harar city, respectively were not significant. Furthermore, milk samples from Dairy Farms revealed a higher prevalence (57.39%) and level (0.252±0.64µg/L) of AFM1 than Milk Vendors, with a prevalence of 42.61% and an average of 0.107±0.21µg/L. Therefore, this study concludes that substantial milk samples were contaminated by AFM1 and urges the need to enhance farmers' awareness on mitigation.

In higher education, the cultivation of research competency is pivotal for students’ critical thinking development and their subsequent transition into the professional workforce. While statistics plays a fundamental role in supporting the completion of a research project, it is often perceived as challenging, particularly by students in majors outside mathematics or statistics. The connection between students’ statistical proficiency and their research competency remains unexplored despite its significance. To address this gap, we utilized the supervised machine learning approach to predict students’ research competency, as represented by their performance in a research methods class, with predictors of students’ proficiency in statistical topics. Predictors relating to students’ learning behavior in a statistics course such as assignment completion and academic dishonesty are also included as auxiliary variables. Results indicate that the three primary categories of statistical skills—namely, understanding of statistical concepts, proficiency in selecting appropriate statistical methods, and statistics interpretation skills— can be used to predict students’ research competency, as demonstrated by their final course scores and letter grades. This study advocates for strategic emphasis on the identified influential topics to enhance efficiency in developing students’ research competency. Findings could inform instructors in adopting a strategic approach to teaching the statistical component of research for enhanced efficiency.

The accumulation of brown algae from the genus Sargassum has been increasing over the years in coastal regions of the Caribbean, Africa, Brazil, and Mexico. This causes harmful effects to the ecosystem, health, economy, and climate due to gas emissions from its decomposition process. There is the possibility of this biomass being reused in civil construction, and few studies have been carried out on its application to common Portland cement mortar. As such, the objective of this study is to evaluate the potential of sargassum ash as a mineral addition to partial replacement of fine aggregates in Portland cement mortar. Characterizations of the raw materials were carried out through X-ray fluorescence spectroscopy, loss on ignition, particle size distribution, Brunauer–Emmett–Teller (BET), real density, X-ray diffraction, scanning electron microscopy, and dispersion spectroscopy of electrons. The mortars were prepared by partially replacing the fine aggregate (sand) with sargassum ash, at 0%, 5%, 10% and 20%. Mortar performance was evaluated through water absorption, apparent porosity, apparent specific mass, compressive strength after 7, 28, and 63 days after curing. Lastly, a life cycle assessment in accordance with ISO standards 14040:2006 and 14044:2006. The results showed that replacing sand with sargassum ash increases water absorption, apparent porosity, and decreases the apparent specific mass and compressive strength as replacement increases. Nevertheless, the compressive strength results after 63 days, for 5 and 10% replacement did not differ statistically from reference values. The life cycle assessment indicates that mortars with partial replacement of sand by sargassum ash showed positive environmental impacts when compared to reference values for most categories regardless of the scenario analyzed, especially for mortar with 10% replacement. As such, the use of sargassum ash at 10% does not alter compressive strength values after 63 days while reducing its environmental impact. The application of this biomass in civil construction materials provides a destination for this algae that has been causing several social, environmental, and economic problems.

Nuclear Magnetic Resonance (NMR) and its various forms are extensively utilized in both research and clinical settings to analyse molecules. NMR data pre-processing, while essential to NMR data analysis, can be uniquely complex. Despite the availability of software tools, understanding these processes can be challenging, complicating the selection of appropriate pre-processing steps. In this review, we elucidate pre-processing steps in the time domain from a mathematical and statistical perspective, explaining direct current offset removal, eddy current correction, shift and linear prediction, weighting, zero filling, and domain transformation using plain language and fundamental mathematical formulas. Our objective is to clarify these processes in simple terms and provide general guidance.

Magnetic Resonance Imaging (MRI) is widely used in clinics and research due to its accurate disease identification and non-invasive nature. MRI is based on Nuclear Magnetic Resonance (NMR), which is also extensively employed in various fields. NMR and its modern versions involve intricate pre-processing steps before data analysis. These steps are initially processed in the time domain and subsequently in the frequency domain. While our previous review focused on time domain pre-processing (https://www.preprints.org/manuscript/202310.2032/v1), this review delves into the mathematical and statistical aspects of frequency domain pre-processing. We discuss essential pre-processing steps like phase error correction, baseline correction, solvent filtering, calibration and alignment, reference deconvolution, binning/bucketing and peak picking, peak fitting/deconvolution and compound identification, integration and quantification, normalization and transformation. Furthermore, we offer practical recommendations for each step.

This paper proposes a novel data processing framework dedicated to bedload monitoring in underwater environments. After calibration, by integration the total energy in the nominal bandwidth, the proposed experimental setup is able to accurately measure the mass of individual sediments hitting the aluminum plate. This require a priori knowledge of the vibration trasients in order to match a predefined dictionary. Based on unsupervised hierarchical agglomeration of complex vibration spectra, the proposed algorithms allow to accurately localize the transients corresponding to the shocks created by sediment impacts on a steel plate.

At present, medical institutes generally use EMR to record patient's condition, including diagnostic information, procedures performed and treatment results. EMR has been recognized as a valuable resource for large scale analysis. However, EMR has the characteristics of diversity, incompleteness, redundancy and privacy, which make it difficult to carry out data mining and analysis directly. Therefore, it is necessary to preprocess the source data in order to improve data quality and improve the data mining results. Different types of data require different processing technologies. Most structured data commonly needs classic preprocessing technologies, including data cleansing, data integration, data transformation and data reduction. For semi-structured or unstructured data, such as medical text, containing more health information, it requires more complex and challenging processing methods. The task of information extraction for medical texts mainly includes NER (Named Entity Recognition) and RE (Relation Extraction). In this paper, we introduce the process of EMR processing, including data collection, data preprocessing, data mining, evaluation and knowledge application, analyze the current status of the key technologies, such as data preprocessing and data mining, and provide an overview of the application domains and prospects of EMR mining technologies. Finally, we summarize the existing problems in the research of EMR mining, and review the development trends.

Room temperature superconductivity has recently been reported for a carbonaceous sulfur hydride (CSH) under high pressure by Snider et al [1]. The paper reports sharp drops in magnetic susceptibility as a function of temperature for five different pressures, that are interpreted as signaling a superconducting transition. Here I question the validity and faithfulness of the magnetic susceptibility data presented in the paper by comparison with the measured raw data reported by two of the authors of ref. [2]. This invalidates the assertion of the paper [1] that the susceptibility measurements support the case for superconductivity in this compound.

Analysis of immediate effects of the COVID-19 pandemic on SMEs in Rwanda aims to assess and quantify the economic and financial impacts of the pandemic during the lockdown and presents options adopted by SMEs to reopen their business opera-tions. It also seeks to recommend options for sustainable and resilient economic recovery from the scars of COVID-19. This analysis used data collected from nearly 220 SMEs located across the country and applied an Exploratory Data Analysis (EDA) and multivariate linear regression models to measure the pandemic effects. The study revealed that firms downsized employment by 36.4 per cent, but data depict significant deviation within SMEs by their size. The COVID-19 pandemic has had a greater magni-tude of negative effects on sales levels among small businesses. Tax amounts were reduced amidst the crisis however, data do not show any significant variations among SMEs. Additionally, SMEs owners applied various coping mechanisms during re-opening. The study used firm-level data, providing detailed and reliable effects of the shocks on business performance. This analysis recommends establishing the medium-term financing and technical support for SMEs to ensure steady and sustainable recovery from pandemic effects as well as strengthening their resilience to any other socio-economics shocks.

Nowadays, inquiries are one of the most important tasks to be executed in order to get valued information. When an inquiry is done to gather information about a human behavior there are some problems inherent to it. One of the main problems is how the information about many different persons can be processed to give good information about their environment. Most of the information gathered by these inquiries is used to analyze the behavior of the respondents. It can be used to estimate the success of a certain product on the market or just to validate the satisfaction of current costumers. The veracity of this information can be critical to model environments with some acceptable level of precision. Modelling environments through Artificial Neural Networks (ANN) is highly common because ANN’s are excellent to model predictable environments using a set of data. ANN’s are good in deal with sets of data with some noise, but they are fundamentally surjective mathematical functions and they aren’t able to give different results for the same input. So if an ANN is trained using data where the same input has different images which can be the case of survey data, this can be a problem for the success of modelling the environment. Therefore is necessary to process the data in order to adjust and eliminate invalid data.

This article discusses the potential advantages of a data processing technique for continuous gravitational wave signals searches in the data measured by ground-based gravitational wave interferometers. Its main advantage over other techniques is that it does not need to search over the signal’s direction of propagation. Although it is a “ coherent method” (i.e. it coherently processes year-long data), it is applied to a data set obtained by multiplying the original time-series with a (half-year) time-shifted copy of it. As a result, the phase modulation due to the interferometer motion around the Sun is automatically canceled in the signal of the synthesized time-series. Although the resulting signal-to-noise ratio is not as high as that of a coherent search, it equals that of current hierarchical methods. In addition, since the signal search is performed over a parameters space of smaller dimensionality, the associated false-alarm probability should be smaller than those characterizing hierarchical methods and result in an improved likelihood of detection.

Machine fault diagnosis systems need to collect and transmit dynamic monitoring signals, like vibration and current signals, at high-speed. However, industrial wireless sensor networks (IWSNs) and Industrial Internet of Things (IIoT) are generally based on low-speed wireless protocols, such as ZigBee and IEEE802.15.4. To address this tension when implementing machine fault diagnosis applications in IIoT, this paper proposes a novel IWSN with on-sensor data processing. On-sensor wavelet transforms using four popular mother wavelets are explored for fault feature extraction, while an on-sensor support vector machine classifier is investigated for fault diagnosis. The effectiveness of the presented approach is evaluated by a set of experiments using motor bearing vibration data. The experimental results show that compared with raw data transmission, the proposed on-sensor fault diagnosis method can reduce the payload transmission data by 99.95%, and reduce the node energy consumption by about 10%, while the fault diagnosis accuracy of the proposed approach reaches 98%.

This review highlights the potential and limitations of mRNA vaccines with a particular focus on mucosal delivery as an alternative to parenteral administration. The strengths of mRNA vaccines are: a) Versatility: they can be adapted to target a wide range of pathogens; b) Faster development: designed and produced more quickly than traditional vaccines; c) High efficacy: effective in preventing severe disease, as demonstrated during the COVID-19 pandemic. Current challenges: a) Delivery: current methods (mainly intramuscular injection) may not be optimal for inducing mucosal immunity; b) Stability: mRNA is fragile and needs to be protected from degradation; c) Safety: potential side effects, including myocarditis, blood clotting, allergic reactions need further investigation. Mucosal delivery could be more effective in preventing the transmission of pathogens and is generally better accepted by the population. Pros: offers the potential to induce local immunity at the site of pathogen entry, potentially providing broader protection; Cons: developing effective delivery systems and adjuvants for mucosal delivery is difficult. Extracellular vesicles as a mucosal delivery system are promising and offer a potentially safe, scalable, and needle-free approach. Future directions: a) Optimizing mRNA constructs: strategies like codon optimization and self-amplifying RNA can improve stability and translation efficiency; b) Rigorous pre-clinical studies are essential before human trials.

The informational synthesis of neural structures, processes, parameters and characteristics that allow a unified description and modeling as neural machines of natural and artificial neural systems is presented. The general informational parameters as the global quantitative measure of the neural systems computing potential as absolute and relative neural power were proposed. Neural information organizing and processing follows the way in which nature manages neural information by developing functions, functionalities and circuits related to different internal or peripheral components and also to the whole system through a non-deterministic memorization, fragmentation and aggregation of afferent and efferent information, deep neural information processing representing multiple alternations of fragmentation and aggregation stages. The relevant neural characteristics were integrated into a neural machine type model that incorporates unitary also peripheral or interface components as the central ones. The proposed approach allows overcoming the technical constraints in artificial computational implementations of neural information processes and also provides a more relevant description of natural ones.

The timely diagnosis of defects at their incipient stage of formation is crucial to extend the life-cycle of technical appliances. This is the case of mechanical-related stress, either due to long aging degradation processes (e.g., corrosion) or in-operation forces (e.g., impact events), which might provoke detrimental damages, such as cracks, disbonding or delaminations, most commonly followed by the release of acoustic energy. The localization of these sources can be successfully fulfilled via adoption of Acoustic Emission (AE)-based inspection techniques through the computation of the Time of Arrival (ToA), namely the time at which the induced mechanical wave released at the occurrence of the acoustic event arrives to the acquisition unit. However, the accurate estimation of the ToA may be hampered by poor Signal-to-Noise ratios (SNRs). In these conditions, standard statistical methods typically fail. In this work, two alternative Deep Learning methods are proposed for ToA retrieval, namely a Dilated Convolutional Neural Network (DilCNN) and a Capsule Neural Network for ToA (CapsToA). These methods have the additional benefit of being portable on resource-constrained microprocessors. Their performance has been extensively studied on both synthetic and experimental data, focusing on the problem of ToA identification for the case of a metallic plate. Results show that the two novel methods can achieve localization errors which are up to 70% more precise than those yielded by conventional strategies, even when the SNR is severely compromised (i.e., down to 2 dB). Moreover, DilCNN and CapsNet have been implemented in a tiny machine learning environment and then deployed on microcontroller units, showing a negligible loss of performance with respect to offline realizations.

“Pecorino” is a typical semi-hard cheese obtained with raw or heat-treated sheep milk using procedures to valorize the raw material's chemical and microbiological properties. In the present study, using a high throughput method of 16S rRNA gene sequencing, we assessed the evolution of the microbiome composition from milk to Pecorino cheese in artisanal processes using milk from Comisana and Lacaune sheep breeds. The comparative analysis of the bacterial com-munity composition revealed significant differences in the presence and abundance of specific taxa in the milk microbiome of the Comisana and Lacaune breeds. NGS analysis also revealed differences in the curd microbiome related to dairy farming practices, which have a relevant effect on the final structure of the Pecorino-cheese microbiome.

In wireless sensor networks (WSNs), each sensor node can estimate the global parameter from the local data in distributed manner. This paper proposed a robust diffusion estimation algorithm based on minimum error entropy criterion with self-adjusting step-size, which are referred to as diffusion MEE-SAS (DMEE-SAS) algorithm. The DMEE-SAS algorithm has fast speed of convergence and is robust against non-Gaussian noise in the measurements. The detailed performance analysis of the DMEE-SAS algorithm is performed. By combining the DMEE-SAS with diffusion minimum error entropy (DMEE) algorithms, an Improving DMEE-SAS algorithm is proposed, in non-stationary environment where tracking is very important. The Improving DMEE-SAS algorithm can avoid insensitivity of the DMEE-SAS algorithm due to the small effective step-size near the optimal estimator, and obtain a fast convergence speed. Numerical simulations are given to verify the effectiveness and advantages of these proposed algorithms.

Intelligent fault diagnosis techniques have replaced the time-consuming and unreliable human analysis, increasing the efficiency of fault diagnosis. Deep learning model can improve the accuracy of intelligent fault diagnosis with the help of its multilayer nonlinear mapping ability. This paper has proposed a novel method named Deep Convolutional Neural Networks with Wide First-layer Kernels (WDCNN). The proposed method uses raw vibration signals as input (data augmentation is used to generate more inputs), and uses the wide kernels in first convolutional layer for extracting feature and suppressing high frequency noise. Small convolutional kernels in the preceding layers are used for multilayer nonlinear mapping. AdaBN is implemented to improve the domain adaptation ability of the model. The proposed model addresses the problem that currently, the accuracy of CNN applied to fault diagnosis is not very high. WDCNN can not only achieve 100% classification accuracy on normal signals, but also outperform state of the art DNN model which is based on frequency features under different working load and noisy environment.

It is essential to deal with data scattered among heterogeneous information sources, which can be structured, semi-structured, or unstructured, to give consumers a cohesive perspective of the data. Information gathering is challenging as a result, and one of the major causes of this is that data sources are developed to support specific applications. A method to simplify this procedure is to use ontology representation as an intermediate step. An ontology represents a knowledge structure that reasonably reflects the real world's complexity and is ideally used in many industries today. This research aims to enhance the functionality of a global ontology system by implementing and integrating a natural language query system. Leveraging NLP-based approaches, we constructed SPARQL queries for our ontologies to facilitate natural language translation into a well-structured query format. A dedicated query component was developed to transform natural language questions into SPARQL queries, with the selection of the optimal query graph to generate the final queries. In the subsequent phase, we explored the integration of distinct sentence encoders to improve latent sentence representations during query construction. The generated SPARQL queries were executed on the global ontology output and then translated into source-specific questions. This innovative approach enables unified access to heterogeneous data sources through a user-friendly natural language querying interface.

The holy town of Joshimath, gateway to the India-China border and religious places like Badrinath, Hemkunt Sahab, Valley of flowers in the Uttarakhand state of India experienced cracks in many of the residential and commercial buildings in the month of November-December 2022 which created panic and relocation of people. The reason(s) for the subsidence is still not known but using the InSAR technology and data from Sentinel-1, SAR data for the region was processed using HyP3 and MintPy for January-December 2022 to understand when the phenomenon started and how much uplift/subsidence the area has underwent in the last one year, as no such study is available till today. The entire town can be classified into two zones with respect to the annual subsidence values. Severe subsidence has been observed in the North and East regions whereas most of the southern region experienced moderate to low subsidence. Since the town is built on the debris of an old landslide, the subsidence may be attributed to the change in the course of the underground water channels due to heavy and continuous construction happening in the region and also due to drop in the water table. The results shows that the subsidence in the region was ongoing since June (from January till May, almost negligible vertical movement was recorded) which accelerated after September (when an uplift was recorded which lasted till October), while the subsidence peaked in the month of December with recorded subsidence of as much as 10 cm in some areas located around the Joshimath town, where most of the residential and commercial buildings are located.

Over the past 30 years, the use of field spectroscopy has risen in importance in remote sensing studies for the characterization of the surface reflectance of materials in situ within a broad range of applications. Potential uses range from measurements of individual targets of interest (e.g. vegetation, soils, validation targets etc.), to characterizing the contributions of different materials within larger spatially-mixed areas as would be representative of the spatial resolution captured by a sensor pixel (UAV to satellite scale). As such, it is essential that a complete and rigorous assessment of both the data-acquisition procedures, and the suitability of the derived data product be carried out. The measured energy from solar-reflected range spectroradiometers is influenced by the viewing and illumination geometries and the illumination conditions which vary due to changes in solar position and atmospheric conditions. By applying corrections, the estimated absolute reflectance (Rabs) of targets can be calculated. This property is independent of illumination intensity or conditions and is the metric commonly suggested to be used to compare spectra even when data are collected by different sensors or acquired under different conditions. By standardizing the process of estimated Rabs, as is provided in the described toolkit, consistency and repeatability in processing are ensured and the otherwise labor intensive and error-prone processing steps are streamlined. The resultant end data product (Rabs) represents our best current effort to generate consistent and comparable ground spectra which have been corrected for viewing and illumination geometries as well as other factors such as the individual characteristics of the reference panel used during acquisition.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

A set of polymer composite bolted T-joints with novel configuration consisting of internal skeleton and external skin was fabricated using a prepreg-RTM co-curing molding process. Experiments were conducted to study their mechanical properties under bending load. A finite element model with a polymer resin area between the skin and skeleton was established and verified by the experimental results. Then, the damage propagation process and failure mechanism of the joint and the influence of three factors related to the layer characteristics of the skin and skeleton were investigated by the validated models. The results show that the bending stiffness and the yield limit load of the novel composite T-joint are 0.81 times and 1.65 times that of the 2A12 aluminum T-joint respectively, while at only 55.4% of its weight. The damage of the joint initiates within the resin area and leads to a degradation of the joint bending performances. The preferred stacking sequence of the skeleton is [0/+45/90/-45]ns when primarily subjected to bending loads. The decrease in bending performances is within 5% with the inclining angle of the skeleton less than 12 degrees. The more layers of 90° in the skin, the better bending performances of the joints, while the more layer of 0°, the poorer bending performances.

In the era of large data, the cloud is increasingly used as a computing environment, necessitating the development of cloud-compatible pipelines that can provide uniform analysis across disparate biological datasets. The WDL Analysis Research Pipelines (WARP) repository is a GitHub repository of open-source, cloud-optimized WDL workflows for biological data processing that are semantically versioned, tested, and documented. A companion repository, WARP-Tools, hosts Docker containers and custom tools used in WARP workflows.

With continuous increase in integration of the semiconductor devices, the requirements on size accuracy and surface quality of the etched lead frame are higher. The etchant is a key factor on etching process and etched surface quality, while effects of the difference in etchants on microscopic etched surface morphology of the Cu alloy have not been directly studied. In this study, the aqua regia, acidic FeCl3 and CuCl2 solutions were used as etchants, and the CuCrSn alloy specimens with different microstructure were etched and characterized. The results show that the etching rate in aqua regia is high, and the grain orientation, grain boundary (GB) and dislocation have significant influence on the local etching rate. The preferential etching of some atomic planes forms steps between grains with different orientations, and the preferential etching around the GB and dislocation group forms grooves, resulting in high surface roughness. For etching of the FeCl3 and CuCl2 etchants, the steps and grooves become blurred, and almost invisible on the surface etched by the CuCl2 etchant, thus the surface roughness is much lower. The CuCrSn alloy surface etched by the aqua regia is clean, with little Cr-rich particles, while high density Cr-rich particles are remained on the surfaces etched with the FeCl3 and CuCl2 etchants. For the same kind of etchant, the ion concentration can affect the etching mechanism and etching surface morphology.

Lactoperoxidase system (LPS) effect on quality of raw and pasteurized milk under real conditions along the dairy value chain in Ethiopia was evaluated. A total of 250 milk samples were collected from farmers, collectors, and factories. Experimental samples were LPS-activated of morning and overnight milk. The samples were tested with several chemical and microbiological tests such as total bacterial count (TBC), total coliform count (TCC) and Escherichia coli count (EC). Results indicated that all LPS-activated milk samples had a higher quality than all the control samples. For instance, both the morning and overnight farm milk samples had a mean TBCs of 5.79 log and 6.55 log cfu/ml which is significantly (p

With the increasing interest in CM as a potential source of nutrients and bioactive compounds, there arises a necessity to delve into methods for its processing and drying. Over recent decades, a significant amount of research has been conducted on the chemical composition of CM and its potential health benefits. Consequently, this study is directed towards examining CM drying technology, including an analysis of the influence of different drying methods on its chemical composition and nutri-tional properties. The objective of this review is to systematically summarize the available literature on CM drying processes and their impact on its chemical composition. Special attention is devoted to comparing various drying methods such as freeze-drying, spray drying, and freeze-drying, as well as investigating factors affecting the quality of dried CM. To achieve this goal, we scrutinize a series of studies published between 2003 and 2022 to identify optimal drying methods that promote the maximum preservation of CM's nutritional components and bioactive compounds. Additionally, we explore possibilities for reducing drying time to enhance production efficiency. This research is grounded in the analysis of data from diverse scientific research databases, including Scopus and Google Scholar, encompassing a systematic review of scientific literature and a comparative analysis of the obtained results.

Two algorithms of data processing are proposed to shorten the unmeasurable dead-zone close to the zero-position of measurement, i.e., the minimum working distance of a dispersive interferometer using optical frequency comb, which is a critical issue in millimeter-order short-range absolute distance measurement. After demonstrating the limitation of the conventional data processing algorithm, the principles of the proposed algorithms, namely the spectral fringe algorithm, and the combined algorithm that combines the spectral fringe algorithm with the excess fraction method, are presented, together with simulation results for demonstrating the possibility of the proposed algorithms for shortening the dead-zone with a high accuracy. An experimental setup of dispersive interferometer is also constructed for implementing the proposed data processing algorithms over spectral interference signals. Experimental results demonstrate that the dead-zone by the proposed algorithms can be as small as half of that by the conventional algorithm while the measurement accuracy can be further improved with the combined algorithm.

Social media data is heavily used to analyze and evaluate situations in times of disasters, and derive decisions for action from it. A cruicial part of the analysis is to avoid unnecessary data retention during that process, in order to prevent subsequent abuse, theft or public exposure of collected datasets and thus, protect the privacy of social media users. There are a number of technical approaches out to face the problem. One of them is using a cardinality estimation algorithm called HyperLogLog to store data in a privacy-aware structure, that can not be used for purposes other than the originally intended. In this case study, we developed and conducted a focus group discussion with teams of social media analysts, in which we identified challenges and opportunities of working with such a privacy-enhanced social media data structure in place of conventional techniques. Our findings show that, with the exception of training scenarios, deploying HyperLogLog in the data acquisiton process will not distract the data analysis process. Instead, it will improve working with huge datasets due to the improved characteristics of the resulting data structure.

The Independent Component Analysis (ICA) has been recently introduced as a reliable alternative to identify canonical scattering mechanisms within Polarimetric Synthetic Aperture Radar (PolSAR) images. This manuscript addresses two important aspects when applying such methods on real data, namely speckle filtering and statistical classification with ICA. A novel PolSAR data processing framework is introduced by adjusting the Lee's sigma filter to the particular nature of the Touzi's polarimetric decomposition. In its current form, it allows the use of the ICA mixing matrix in the derived speckle filter. An extension of the Fromont at al. iterative segmentation is introduced, equally. This proposed framework is tested using P band airborne PolSAR data acquired for the ESA campaign TropiSAR campaign.

In this paper we describe a method which combines sentiment analysis with machine learning techniques and/or multivariate statistical analysis. By applying this methodology it is possible to classify a collection of texts into two or more groups or clusters. On the basis of a number of previously defined clusters, the novelty of the outlined approach is the use of the sentiment analysis results as input to the machine learning model or multivariate statistical analysis. Once the classifier has been obtained, we can assign a given text into one of the pre-established clusters. The groups or clusters can represent different time periods, classes of texts transcribed from different conversations, etc. The method is illustrated through an example taken from one of the two studies in which we have applied this methodology. In one of the studies, the method was used to classify press news of a volcanic eruption, while in the other study it was used to classify the conversations recorded between a chatbot with different kinds of speakers (humans or chatbots). This last study was the seminal work in which we introduced this methodology.

Real-time data processing and decision-making are increasingly crucial in various applications, driven by the continuous influx of data streams. Event-driven AI workflows within serverless computing environments offer a promising approach to handle these real-time demands efficiently. This paper presents a framework for simulating and analyzing the performance characteristics of such workflows. Our proposed approach utilizes simulated data with varying event rates and durations to investigate the impact on key performance metrics like latency, throughput, and resource utilization. This enables a comprehensive evaluation of the inherent trade-offs within event-driven AI systems. The key findings reveal a trade-off between latency and throughput. As the event rate increases, average processing latency generally increases while average throughput increases. Resource utilization remains relatively stable across different event rates in the simulated scenarios (e.g., 75.55\% at 2 events/second, 74.51\% at 10 events/second). This framework provides a valuable tool for understanding the performance characteristics of event-driven AI workflows and optimizing resource allocation strategies.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

The essence of cross-modal generation and retrieval modeling for image-text interactions lies in semantic consistency. Among these, cross-modal representation alignment serves as the foundational requirement for achieving cross-modal semantic consistency. The crux of our proposed method entails the collaborative training of an image captioning model(referred to as the ’captioner’) and a pair of contrastive encoders for image-text matching(referred to as the ’concoder’). This synergistic approach yields concurrent enhancements in concoder’s performance, captioner’s proficiency, and cross-modal semantic coherence. We coin the proposed method as ‘ReCap’. To begin, we initialize the concoder through knowledge distillation from a pre-trained model. During the training process, we use the output of the initialized concoder as input to a residual attention network, jointly training it with the captioner to achieve semantic consistency. Subsequently, we iteratively update the concoder during the image-text momentum encoding phase using the residual attention network, creating a closed-loop for semantic consistency resolution. Upon completion of training, the concoder and captioner modules can be used independently to perform tasks related to cross-modal retrieval and cross-modal generation of text and images. In order to substantiate the efficacy of our proposed method, we initially conducted empirical experiments encompassing image-text retrieval and image captioning tasks, employing a widely recognized benchmark dataset, MSCOCO. Subsequently, we assessed the fine-grained cross-modal alignment performance of the concoder through an image classification task on the iNaturalist 2018 dataset. The achieved performance metrics notably surpassed those achieved by several incumbent state-of-the-art models, thus validating the proficiency of our method. Finally, motivated by the practical requirements of handling the nature conservation image data, we performed caption annotation for the iNaturalist 2018 dataset. Subsequently, we trained the ReCap on this annotated data. Experimental results demonstrate that our proposed method can maintain semantic consistency between cross-modal retrieval and image caption generation for species with similar visual features but distinct semantics. This achievement signifies a meaningful exploration in the field of cross-modal semantic consistency representation, holding significant practical value in the domain of biological research.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

The dual-station Interferometric Synthetic Aperture Radar (InSAR) system can overcome the physical limitations imposed by the baseline of single-station dual-antenna InSAR. It provides greater flexibility and can enhance elevation measurement accuracy through a well-designed baseline configuration.Unmanned aerial vehicles (UAV) equipped with dual-station InSAR, with relatively low cost and high flexibility, are useful for mapping and land resource exploration. However, due to challenges including spatiotemporal synchronization and motion errors, there are limited reports on UAV-borne dual-station InSAR. This paper proposes a comprehensive method for processing data from small UAV-borne dual-station InSAR by integrating two-way synchronization chain signals. The proposed method includes compensation for time and phase synchronization errors, trajectory refinement with synchronized chain and Position and Orientation System (POS) data, high-precision dual-station InSAR imaging and interferometric processing. Height inversion results based on the proposed method is also provided, demonstrating the effectiveness of the proposed method and improving interferometric accuracy at calibration points from 0.66 meters to 0.42 meters.

Exploration geochemistry is an essential method for discover new mineral areas. However, with the increase of exploration degree, relying solely on "strong, broad and multiple" anomalies to guide exploration work has become increasingly challenging. How to effectively identify valuable geochemical information remains a hot and frontier topic in the field. Thus we proposed a geological connotation method (GCM) that provides an objective geological connotation to big geochemical data based on regional geological and geochemical characteristics of known typical deposits. There are mainly two types of geochemical anomalies expression: (1) the metallogenic intensity anomaly map (MIAM) obtained by accumulating specific anomalous elements, which directly reflects the degree of material exchange and superposition modification during mineralization; (2) the metallogenic type anomaly map (MTAM) obtained by accumulating the mineralization concentration coefficients of elements related to a certain genetic type, which can highlight the anomalies caused by a specific genetic type of deposit. These have been tried and applied in the exploration of the Gangdese, North Himalayas, Nyenchen Tanglha and other metallogenic belts in Tibet, and have made a series of breakthroughs in mineral resources exploration represented by Qulong, Zhunuo and Zhaxikang. The advantage of GCM is that it not only solves the problem of missing ore in the verification of "strong, broad and multiple" anomalies, but also can quickly and preferably delineate the strongest mineralized areas, and better overcome the influence of numerous factors on the anomalies, such as the chemical nature of elements, redox environment, geomorphic landscape and weathering and stripping, so that the anomaly evaluation becomes simple, objective and highlights the regularity.

In the neuroscience research field, specific for medical imaging analysis, how to mining more latent medical information from big medical data is significant for us to find the solution of diseases. In this review, we focus on neuroimaging data that is functional Magnetic Resonance Imaging (fMRI) which non-invasive techniques, it already becomes popular tools in the clinical neuroscience and functional cognitive science research. After we get fMRI data, we actually have various software and computer programming that including open source and commercial, it's very hard to choose the best software to analyze data. What's worse, it would cause final result imbalance and unstable when we combine more than software together, so that's why we want to make a pipeline to analyze data. On the other hand, with the growing of machine learning, Python has already become one of very hot and popular computer programming. In addition, it is an open source and dynamic computer programming, the communities, libraries and contributors fast increase in the recent year. Through this review, we hope that can make neuroimaging data analysis more easy, stable and uniform base the one platform system.

Time-series analysis is a widely used technique across various fields and industries, as it helps in understanding, predicting, and forecasting the behavior of data points over time. These fields include but are not limited to finance, economics, healthcare, transportation, etc. In the case of this paper, we have focused on finance. Predicting future values of financial time series offers several benefits. Accurate forecasts can help investors make better decisions about their investments. To predict future values, deep learning algorithms are commonly used since it is an effective method with complex data. In this study, we conduct a study that investigates the use of different data pre-processing techniques on deep learning algorithms in predicting the time series values. To conduct this experimental study, we utilize an open source software, which using long short-term memory technique as the representative deep learning technique, published in github software code repository platform. With this study, we investigate the effects of autoencoder and discrete wavelet transform data pre-processing techniques in time-series prediction. We discuss the details of the experimental study and report our results. The results show that time series prediction (using backtesting methodology) without any data pre-processing leads to 12.6% for mean absolute percentage error. The results also show that, time series prediction with the data preprocessing techniques (Wavelet Transform and Stacked Autoencoder) lead to 3.4%

In recent years, since flood disasters have brought immeasurable losses to the city, it is urgent to prevent and solve the flood of stagnant water. Considering the shortage of real-time and accuracy of hydrological analysis, Opencv technology is used in this paper to process the obtained data in real time. For improved Yolov5, BoTNet and GAMAttention Transformer are used to improve Yolov5 to enhance its ability of recognition and prediction to better identify surface gathered water. The prediction rate of the improved Yolov5 is 7.1% higher than that of Yolov7 and 1.7% higher than that of Yolov5.After that, contour preprocessing of the image is carried out through the cropping technology of the identification frame to eliminate relatively unstable factors. The principle of binocular distance measurement is used to measure the three-dimensional coordinates of the actual distance, better constrain the contour proportion of the picture, and then the Opencv technology is used to get the outline of the water, and HSV is combined with better color processing pictures for the identification of the water and contour generation, and the area is obtained to correspond to the corresponding parameters of flood to provide important help in flood prevention and storm drainage.

Untargeted metabolomics is a powerful tool for measuring and understanding complex biological chemistries. However, employment, bioinformatics and downstream analysis of mass spectrometry (MS) data can be daunting for inexperienced users. Numerous open-source and free-to-use data processing and analysis tools exist for various untargeted MS approaches, including liquid chro-matography (LC), but choosing the ‘correct’ pipeline isn’t straight-forward. This tutorial, in con-junction with a user-friendly online guide presents a workflow for connecting these tools to process, analyse and annotate various untargeted MS datasets. The workflow is intended to guide explor-atory analysis in order to inform decision-making regarding costly and time-consuming down-stream targeted MS approaches. We provide practical advice concerning experimental design, organisation of data and downstream analysis, and offer details on sharing and storing valuable MS data for posterity. The workflow is editable and modular, allowing flexibility for updated/ changing methodologies and increased clarity and detail as user participation becomes more common. Hence, the authors welcome contributions and improvements to the workflow via the online repository. We believe that this workflow will streamline and condense complex mass-spectrometry approaches into easier, more manageable, analyses thereby generating opportunities for researchers previously discouraged by inaccessible and overly complicated software.

The main contribution of this paper is to develop a graphical tool to evaluate the suitability of a candidate parametric model to fit a data set. The practical motivation is to check the adequacy of the so called SAINT model proposed in Jarner and Kryger (2011). This model has been implemented in practice by an important European pension fund concerned with setting annuity reserves for all current or former employees of Denmark. So, one particular relevant question is whether this mortality model is actually fitting old-age. Our graphical test can be described as follows. First we transform the data by means of the parametric model which is being evaluated. Should the model be correct, the transformed data will be in accordance with an Exponential distribution with rate 1. Then we construct a family of local linear hazard estimates based on the data on the transformed scale. Finally we use the statistical tool SiZer to assess the goodness-of-fit of the Exponential distribution to the data on the transformed scale. If the model is correct the SiZer map should not reveal any significant feature in the family of kernel estimates. Our method allow us to establish a diagnostic regarding the validity of the SAINT model when describing mortality patterns in four different countries.

Quantum computing (QC) has opened the door to advancements in machine learning (ML) tasks that are currently implemented in the classical domain. Convolutional neural networks (CNNs) are classical ML architectures that exploit data locality and possess a simpler structure than fully-connected multi-layer perceptrons (MLPs) without compromising the accuracy of classification. However, the concept of preserving data locality is usually overlooked in the existing quantum counterparts of CNNs, particularly for extracting multi-features in multidimensional data. In this paper, we present a multidimensional quantum convolutional classifier (MQCC) that performs multidimensional and multi-feature quantum convolution with average and Euclidean pooling and thus adapting the CNN structure to a variational quantum algorithm (VQA). Average pooling is based on the quantum Haar transform (QHT) and Euclidean pooling is based on partial quantum measurement. The experimental work was conducted using multidimensional data to validate the correctness and demonstrate the scalability of the proposed method utilizing both noisy and noise-free quantum simulations. We evaluated the MQCC model with reference to reported work on state-of-the-art quantum simulators from IBM Quantum and Xanadu using a variety of standard ML datasets. The experimental results showed favorable characteristics of our proposed techniques compared to existing work with respect to a number of quantitative metrics such as the number of training parameters, cross-entropy loss, classification accuracy, circuit depth, and quantum gate count.

Specific climate adaptation and resilience measures can be efficiently designed and implemented at the regional and local level. Climate and environmental databases are of critical importance to achieving sustainability goals (SDGs) and for the efficient planning and implementation of suitable mitigation measures: Available databases can serve municipalities as a vital starting points to determine requirements, prioritize resources and allocate investments under consideration of commonly tight budget restrictions. High-quality geo, climate and environmental data are now available – data from remote sensing, i.e. Copernicus services will be of crucial importance. Forward-looking approaches exist to using such data to derive forecasts for urban planning process optimization for municipal administrations. On municipal level, however, the existing data have so far only been used to a limited extent, since there are no practical tools for urban planning that can be used to merge and meaningfully combine remote sensing data with local data and to further process and apply in municipal planning processes. Therefore, our project CoKLIMAx aims at the development of new digital products, advanced urban services and procedures, such as the development of practice-oriented technical tools that acquire various remote sensing and in-situ data sets for validation and further processing.

Surfaces of additively manufactured metal parts from powder-based processes typically show powder particle agglomerations and other features, resulting in high surface roughness. Proper characterization of those surfaces is necessary in order to assess part quality with respect to coatability, mechanical performance or corrosion resistance for use in aerospace, automotive, medical and more industrial applications. Optical surface texture measurement allows for collection of areal surface data, while the established contact stylus method only captures line profile data. When applying optical methods for surface topography measurements, proper data acquisition and post-processing in order to assess surface texture may be complex. A number of variables can be adjusted, such as different measurement settings, approaches to outlier removal, evaluated area size or form removal. This work shows the influence of selected z-range prior to measurement and the influence of choosing pre-defined outlier removal settings in MountainsMap 9.2 on selected ISO 25178-2:2022 parameters calculated from data obtained from confocal microscopy for as-built Ti6Al4V from laser powder bed fusion. The aim is to show the influence of variation in measurement and post-processing on calculated surface texture parameters and stress the importance of proper documentation in order to achieve reproducibility of data for quality management.

The application of 3D LiDAR technology has become increasingly extensive in tunnel monitoring due to the large density and high accuracy of the acquired spatial data. The proposed processing method aims at circle tunnels and provides a clear workflow to automatically process raw point data and easily interpretable results to analyze tunnel health state. The proposed automatic processing method employs a series of algorithms to extract point cloud of a single tunnel segment without obvious noise from entire raw tunnel point cloud mainly by three steps: axis acquisition, segments extraction and denoising. Tunnel axis is extracted by fitting boundaries of the tunnel point cloud rejection in plane with RANSAC algorithm. With guidance of axis, the entire preprocessed tunnel point cloud is segmented by equal division to get a section of tunnel point cloud which corresponds to a single tunnel segment. Then the noise in every single point cloud segment is removed by clustering algorithm twice, based on distance and intensity. Finally, clean point clouds of tunnel segments are processed by effective deformation extraction processor to get ovality and three-dimensional deformation nephogram.

For a wide field of view (FoV) wavefront coding athermalized infrared imaging system with a single decoding kernel, the off-axis aberration tends to cause artefacts. In order to correct off-axis aberration, many pieces of lenses will reduce the transmission efficiency and increase the weight and cost. To meet requirements for wide FoV, wide operating temperature and low weight of infrared imaging systems, this paper reports a wide-FoV wavefront coding athermalized infrared imaging system with a two-piece lens. Its principle, design, manufacture, measurement and performance validation are successively discussed. This paper constructs an optimization problem which maximizes the weighted mean of PSF consistency for both the FoV and operating temperature range. The two-piece lens contains four surfaces, where three aspheric surfaces are introduced to reduce optical off-axis aberrations and a cubic surface is introduced to achieve athermalization. The optical phase mask containing an aspheric surface and a cubic surface is manufactured by nano-metric machining of ion implanted material(NiIM). Experimental results validate that our wide-FoV wavefront coding athermalized infrared imaging system has a full FoV of 26.10° and an operating temperature over -20°C to +70°C.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

In a dynamic production processes, mechanical degradation poses a significant challenge, impacting product quality and process efficiency. This paper explores a novel approach for monitoring degradation in the context of viscose fiber production, a highly dynamic manufacturing process. Using causal discovery techniques, our method allows domain experts to incorporate background knowledge into the creation of causal graphs. Further, it enhances the interpretability and increases the ability to identify potential problems via changes in causal relations over time. The case study employs a comprehensive analysis of the viscose fiber production process within a prominent textile industry, emphasizing the advantages of causal discovery for monitoring degradation. The results are compared with state-of-the-art methods, which are not considered to be interpretable, specifically LSTM-based autoencoders, showcasing the alignment and validation of our approach. This paper provides valuable information on degradation monitoring strategies, demonstrating the efficacy of causal discovery in dynamic manufacturing environments. The findings contribute to the evolving landscape of process optimization and quality control.

In recent years, demand for consumption of marine foods, and especially fish, has substantially increased worldwide. The majority of collagen available is sourced from mammalian-derived products. Although fish derived gelatine is a viable alternative to mammalian sourced gelatine, there are some challenges related to the use of fish gelatine including odour, colour, gelling and film forming properties as well as consistency in gelatine amino acid composition. Chemicals used for pre-treatment, as well as extraction conditions such as temperature and time, can influence the length of polypeptide chains that result and the functional properties of the gelatine. Compared to mammalian sources, gelatines derived from fish show notable differences in physical and chemical properties, and great care should be paid to optimization of the production process in order to obtain a product with the best properties for intended applications. The focus of this review is to explore the feasibility of producing gelatine sourced from marine processing by-products using different pre-treatment and extraction strategies with the aim of improving the techno-functional properties of the final product and improving the clean-label status of gelatines. The bioactivities of gelatine hydrolysates are also discussed.

In recent years, demand for consumption of marine foods, and especially fish, has substantially increased worldwide. The majority of collagen available is sourced from mammalian-derived products. Although fish derived gelatine is a viable alternative to mammalian sourced gelatine, there are some challenges related to the use of fish gelatine including odour, colour, gelling and film forming properties as well as consistency in gelatine amino acid composition. Chemicals used for pre-treatment, as well as extraction conditions such as temperature and time, can influence the length of polypeptide chains that result and the functional properties of the gelatine. Compared to mammalian sources, gelatines derived from fish show notable differences in physical and chemical properties, and great care should be paid to optimization of the production process in order to obtain a product with the best properties for intended applications. The focus of this review is to explore the feasibility of producing gelatine sourced from marine processing by-products using different pre-treatment and extraction strategies with the aim of improving the techno-functional properties of the final product and improving the clean-label status of gelatines. The bioactivities of gelatine hydrolysates are also discussed.

The healthcare domain is increasingly adopting IoT and Electronic Health Record (EHR) systems, generating vast volumes of healthcare data. This shift is driven by the growing need of delivering the right information to the right individuals, at the right time. The latter underscores the importance of adopting a comprehensive strategy for efficiently collecting, utilizing, and analyzing health-related data to not only enhance overall healthcare management but also for the provision of timely and personalized prevention strategies. The latter is of highest importance especially in scenarios where lack of effective treatments or poor survival rates (such in pancreatic cancer) renders typical healthcare strategies ineffective. In this article, we introduce an innovative and integrated platform that is specifically designed and developed for accessing, processing, and analyzing data in challenging healthcare scenarios, such as dealing with pancreatic cancer. This platform, called iHelp, combines multidisciplinary technologies and provides healthcare professionals reliable risk modelling, analysis, and prediction techniques so that individuals (at risk of developing pancreatic cancer) can be provided with timely, reliable, and personalized prevention and intervention measures. A key innovation in the iHelp platform is the standardized data management approach called Holistic Health Records (HHRs) that facilitate the capturing of all health determinants in a standardized and well-structured way for processing towards the provision of health risk detection and personalized healthcare decision support. In the development of iHelp platform, the HHRs are evaluated through different real-world healthcare datasets, including datasets coming from hospital systems, data from wearables, questionnaires, and mobile applications.

High level of noise is a disturbance to the human environment. Noise in industries is also an occupational hazard because of its attendant effects on workers’ health. Noise presents health and social problems in industrial operations, and the source is related to the machineries used in the industries. One of the unique features of the noise associated with wood machinery is the level of exposure and duration. Equipment used in a factory can be extremely loud. They can produce noise at decibels high enough to cause environmental health and safety concerns. The mechanically driven transport and handling equipment, cutting, milling, shaping and dust extractor installations in the wood industry generate noise. The sources of noise pollution have increased due to non-compliance with basic safety practices. The increased use of locally fabricated machine in the industry has increased the level of noise and vibration. The effects of industrial noise pollution as discussed include: increase in blood pressure; increased stress; fatigue; vertigo; headaches; sleep disturbance; annoyance; speech problems; dysgraphia, which means reading/learning impairment; aggression; anxiety and withdrawal. As presented in this paper, noise control techniques include; sound insulation, sound absorption, vibration damping and Vibration isolation.

Online food delivery services are rapidly growing in popularity, making customer satisfaction critical for company success in a competitive market. Accurate delivery time predictions are key to ensuring high customer satisfaction. While various methods for travel time estimation exist, effective data analysis and processing are often overlooked. This paper addresses this gap by leveraging spatial data analysis and preprocessing techniques to enhance the data quality used in Bayesian models for predicting food delivery times. We utilized the OSRM API to generate routes that accurately reflect real-world conditions. Next, we visualized these routes using various techniques to identify and examine suspicious results. Our analysis of route distribution identified two groups of outliers, leading us to establish an appropriate boundary for maximum route distance to be used in future Bayesian modelling. The spatial analysis revealed that these outliers were primarily deliveries to the outskirts or beyond the city limits. By refining the data quality through these methods, we aim to improve the accuracy of delivery time predictions, ultimately enhancing customer satisfaction.

Robot Operating System 2 (ROS 2) is a robotic software that uses a set of Quality of Service (QoS) policies to manage the quality of robot data transmissions in a network, such as the RELIABLE and KEEP_LAST options. In ROS 2 node communication, the RELIABLE connection guarantees that all message data can be properly sent from the publisher to the subscriber. However, strict reliability is not guaranteed if the RELIABLE connection uses the KEEP_LAST option to transmit the robot data in the publish-subscribe communication. This study aims to analyze the efficiency of local cache, cache control, and QoS balancing optimization to improve ROS 2 node communication when using the RELIABLE and KEEP_LAST options to transmit multi-robot data in Aggregated Robot Processing (ARP) architecture. Our idea in local cache and cache control is to streamline the sensor data output before processing it when the sensor device produces the data with the same value in a row. Furthermore, QoS balancing optimization aims to balance the DEPTH and DEADLINE QoS configuration to determine the rates and buffer size in ROS 2 node communication. This study shows that combining local cache and QoS balancing optimization improves multi-robot data transmission and cooperation in ARP architecture.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

The cosmetics industry is currently looking for innovative ingredients with higher bioactivity and bioavailability for the masses of natural and organic cosmetics. Bioferments are innovative ingredients extracted from natural raw materials by carrying out a fermentation process with appropriate strains of microorganisms. The review was conducted using the SciFinder database with the keywords fermented plant, cosmetics, fermentation. Mainly bioferments are made from plant-based raw materials. The review covers a wide range of fermented raw materials from waste materials (whey with beet pulp) to plant oils (F-Shiunko, F-Artemisia, F-Glycyrrhiza). The spectrum of applications for bioferments is broad and includes properties such as skin whitening, antioxidant properties (blackberry, soybean, goji berry), anti-ageing, anti-aging (red ginseng, black ginseng, Citrus unshiu peel), hydrating and anti-allergic (aloe vera, skimmed milk). Fermentation increases the biochemical and physiological activity of the substrate by converting high-molecular compounds into low-molecular structures, this makes fermented raw materials more compatible compared to unfermented raw materials.

In this paper, we studied the problem of early detection of natural phenomena associated with the formation of severe floods and the possibility of constant monitoring of their occurrence. The test object for the study was severe floods on the Crimean Peninsula, which occurred due to heavy rainfall in the summer of 2021. Based on the selected satellite and other data related to this period, an analysis carried out and key atmospheric objects identified, according to the proposed algorithm for their identification and grouping. Based on the results of the work, a positive conclusion made on the issue of their use to identify the likelihood of natural disasters that could lead to floods. In addition, the authors proposed to develop a portal for collecting and processing a large amount of satellite data related to flood prevention and monitoring the development of such processes, and stressed the need to create it.

The raw material purchasing (RMP) problem is to determine the purchasing quantities of raw materials in given periods or cycles. Raw material purchasing optimization is crucial for large-scale steel plants because it is closely related to the supply of raw materials and cost savings. The raw material purchasing of large-scale steel enterprises is characterized by many varieties, large quantities, and high costs. The RMP objective is to minimize the total purchasing cost consisting of the price of raw materials, purchasing set-up costs, and inventory costs and meet product demand. We present a mixed integer linear programming (MILP) model and a column generation (CG) solution for the resulting optimization problem. The column generation algorithm is the generalization of the branch & bound algorithm with solving the linear programming (LP) relaxation of MILP using column generation (CG), and its advantage is to handle large-sized MILPs. Experimental results show the effectiveness and efficiency of the solution.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

Attribute reduction is a core technique in the rough set domain and an important step in data preprocessing. Researchers have proposed numerous innovative methods to enhance the capability of attribute reduction, such as the emergence of multi-granularity rough set models, which can effectively process distributed and multi-granularity data. However, these innovative methods still have many shortcomings, such as how to deal with complex constraints and how to perform multi-angle effectiveness evaluations. Based on the multi-granularity model, this study proposes a new method of attribute reduction, namely using multi-granularity neighborhood information gain ratio as the measurement criterion. This method combines both supervised and unsupervised perspectives, and by integrating multi-granularity technology with neighborhood rough set theory, constructs a model that can adapt to multi-level data features. This model can select the optimal granularity level or attribute set according to the requirements. Finally, the proposed method is experimented with on 15 UCI datasets against six other attribute reduction algorithms. The experimental outcomes, upon analysis and comparative review, substantiate the reliability and consistency of the attribute reduction approach introduced in this study.

Quaking aspen (Populus tremuloides Michx.) is an important deciduous species in western U.S. forests. Existing maps of aspen distribution are based on Landsat imagery and often miss small stands (<0.09 ha or 30 m²), which rapidly regrow when managed or following disturbance. In this study, we present methods for deriving a new regional map of aspen forests using one year of Sentinel-1 (S1) and Sentinel-2 (S2) imagery in Google Earth Engine. We assessed the annual phenology of aspen in the Southern Rockies and leveraged the frequent temporal resolution of S1 and S2 to create ecologically relevant seasonal composites. Additionally, we derived spectral indices and radar textural features targeting the canopy structure, moisture, and chlorophyll content. Using spatial block cross-validation and Random Forests, we assessed the accuracy of different scenarios and selected the best performing set of features for classification. Comparisons were then made with existing landcover products across the study region. The resulting map improves on existing landcover products in both accuracy (average F1-score = 93.1%) and detection of smaller forest patches. These methods enable accurate mapping at spatial and temporal scales relevant to forest management for one of the most widely distributed tree species in North America.

This paper proposes several LabVIEW applications to accomplish the data acquisition, processing, features extraction and real-time classification of the electroencephalographic (EEG) signal detected by the embedded sensor of the NeuroSky Mindwave Mobile headset. The LabVIEW applications are aimed at the implementation of a Brain-Computer Interface system, which is necessary to people with neuromotor disabilities. It is analyzed a novel approach regarding the preparation and automatic generation of the EEG dataset by identifying the most relevant multiple mixtures between selected EEG rhythms (both time and frequency domains of raw signal, delta, theta, alpha, beta, gamma) and extracted statistical features (mean, median, standard deviation, route mean square, Kurtosis coefficient and others). The acquired raw EEG signal is processed and segmented into temporal sequences corresponding to the detection of the multiple voluntary eye-blinks EEG patterns. The main LabVIEW application accomplished the optimal real-time artificial neural networks techniques for the classification of the EEG temporal sequences corresponding to the four states: 0 - No Eye-Blink Detected; 1 - One Eye-Blink Detected; 2 – Two Eye-Blinks Detected and 3 – Three Eye-Blinks Detected. Nevertheless, the application can be used to classify other EEG patterns corresponding to different cognitive tasks, since the whole functionality and working principle could estimate the labels associated with various classes.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

Educational institutions must identify students who are academically struggling to provide them with necessary support to improve their performance. In this context, recommendation systems powered by deep learning techniques are vital for detecting and categorizing such students. These systems help students plan their future by uncovering patterns in their historical academic data. This study introduces a new deep learning model designed to classify academically underperforming students in educational settings. The model incorporates a Gated Recurrent Neural Network (GRU) and includes specific neural network features like a dense layer, max-pooling layer, and the ADAM optimization algorithm. The model's training and evaluation were conducted using a dataset comprising 15,165 student assessment records from various academic institutions. The performance of the developed GRU model was benchmarked against other educational recommendation systems, including Recurrent Neural Network models, AdaBoost, and the Artificial Immune Recognition System v2. The proposed GRU model demonstrated remarkable accuracy, achieving an overall rate of 99.70%.

Flow field based methods are becoming increasingly popular for the analysis of interfacial shear rheology data. Such methods take properly into account the subphase drag by solving the Navier-Stokes equations for the bulk phases flows, together with the Boussinesq-Scriven boundary condition at the fluid-fluid interface, and the probe equation of motion. Such methods have been successfully implemented at the double wall-ring (DWR), the magnetic rod (MR), and the bicone interfacial shear rheometers. However, a study of the errors introduced directly by the numerical processing is still lacking. Here we report on a study of the errors introduced exclusively by the numerical procedure corresponding to the bicone geometry at an air-water interface. In our study we directly input a preset the value of the complex interfacial viscosity and we numerically obtain the corresponding flow field and the complex amplitude ratio for the probe motion. Then we use the standard iterative procedure to obtain the calculated complex viscosity value. A detailed comparison of the set and calculated complex viscosity values is made upon changing different parameters such as real and imaginary parts of the complex interfacial viscosity and frequency. The observed discrepancies yield a detailed landscape of the numerically introduced errors.