Mountain fire can become more complex than fires at lower elevation due to the complex interaction of fire, topography, and weather. The Gell River Fire in Tasmania, Australia occurred in rugged terrain where there are abundant fire sensitive vegetation communities, as well as the presence of infrastructure including high-voltage transmission lines. The fire began at the end of December 2018 and lasted a few months, with a final burnt area of approximately 350km² despite significant fire suppression effort. The fire was investigated by employing wind vector maps, numerical weather model vertical sounding charts (NWMVS) and Prototype 2, which is an integrated fire simulator and can detect lateral fire channeling (LFC). Our analysis of the fire found its spread was likely to be introduced into a valley by forced channeling (FC), which is modified synoptic wind, and showed rapid spread in the valley. The simulated fire also showed wider spread than the observed data in the valley, with the simulated fire impacting highly sensitive vegetation communities on the fringes of the valley. This alludes to some potential conclusions: (1) The loss of fire sensitive vegetation would have increased if fire suppression activity had not been conducted. (2) Spotting fires could be produced by LFC because these spotting fire would allow spreading fire in a shorter period. (3) Heterogeneity of vegetation, such as combination of buttongrass and forest, could help carry fire rapidly in the valley with LFC. Fire can propagate faster in buttongrass than in forests while the forests allow the spotting fire.

Earth’s land surface area is raised from conventionally flat 15 to 64 Gha to account for hilly undulation and soil relief detail. Three main aspects are: topography, rugosity/tortuosity and micro-relief/porosity of vegetation-free ground. Recalibration is arrived at from four approaches: first, direct empirical estimates from the few compiled satellite or LiDAR data with means of +2.5–26% progressively overlain by +94% at cm² scale for soil ruggedness then +108% for mm² micro-relief; second, from digital elevation models with 1.6–2.0 times flat areas; third, by ‘reverse engineering’ global soil bulk densities and carbon reserves requiring x 2–6 land. Finally, a Fermi estimation conveniently sets the World’s new surface area – that exposed to Sun, air and rain – at 100 Gha (with 36 Gha flat ocean). Soil organic carbon (SOC) is thence raised to 8,580 Gt mainly in SOM/humus with its biotic complexity plus roots, VAM-fungi and leaf-litter, that itself = 17,800 Gt. Although four to six times IPCC’s or NASA/NOAA’s calculations of just 1,500–2,300 Gt SOC, this is likely an underestimation. Global biomass and biodiversity are at least doubled (x 2–3.5) and net primary productivity (NPP) similarly increased on land to >270 Gt C yr^-1 due to terrain.

Although mountain areas account for approximately one fifth of the terrestrial surface, there has been less research focused on fire in these areas compared to lowlands. Mountain fires have distinct behavior due to dynamic winds interacting with the terrain, which can influence the fireline intensity and propagation. For the sake of fire safety of fire crews, it is essential to know how difficult to control the fire is in the mountain regions, with fireline intensity providing a useful indicator of risk and suppressibility. We studied one of the major disasters, wildfire, in Australia in such a highland by using the Great Pine Tier Fire, which occurred 15^th January in 2019, ending up burning approximately 511.86km². Weather and fire intensity at pseudo weather stations located at key points of fire progression were analyzed by wind vector maps and numerical weather model vertical sounding (NWMVS). Fire propagation was then simulated in Prototype 2, a fire simulator capable of detecting the potential for lateral fire channeling (LFC), and simulating fireline intensity using Australian vegetation sub-models. We found that the synoptic wind appeared to be modified by the interaction with the terrain in windward and the fire intensified the most in its leeward. In practice, the fire moved out of the valley axis and up its sidehill by following the wind which had been modified by local vertex of the curved valley axis before reaching this location.

The challenging terrain and deep ravines characteristic of mountainous regions often result in slower path planning and suboptimal flight paths for Unmanned Aerial Vehicles (UAVs) when traditional meta-heuristic optimization algorithms are employed. This study investigates the application of an Improved Enhanced Snake Optimizer (IESO) for three-dimensional path planning in a simulated rugged mountainous terrain. The initialization process in the enhanced snake optimizer is refined by integrating the Chebyshev chaotic map. Additionally, a non-monotonic factor is introduced to modulate the "temperature," and a boundary condition is incorporated into the dynamic opposition learning mechanism. These modifications collectively reduce the likelihood of population convergence to local optima during optimization. The feasibility of IESO is validated through time complexity and global convergence analyses. Comparative simulation experiments benchmarked IESO against five state-of-the-art optimization algorithms across test functions and path-planning simulated scenarios. The experimental results indicate that the enhanced algorithm achieves superior optimization precision, faster convergence speeds, and improved quality in the planned trajectories by 30%.

Electron Channeling Contrast Imaging (ECCI) is becoming a powerful tool in Materials Science for characterizing deformation defects. Dislocations observed by ECCI in Scanning Electron Microscope, exhibit several features depending on the crystal orientation relative to the incident beam (white/black line on a dark/bright background). In order to bring new insights concerning these contrasts, we report an original theoretical approach based on the dynamical diffraction theory. Our calculations led, for the first time, to an explicit formulation of the backscattered intensity as a function of various physical and practical parameters governing the experiment. Intensity profiles are modeled for dislocations parallel to the sample surface for different channeling conditions. All theoretical predictions are consistent with experimental results.

Fires constitute a significant threat due to the pollutants emitted and the destruction they cause. People who take part in fire-fighting operations must be equipped with appropriate tools, including special clothing that will allow them to work and guarantee safety. One of the threats are compounds from the PAH group, which are characterized by high toxicity and carcinogenicity. Therefore, it is important that the materials used constitute a barrier to contamination. Various materials from which individual elements of special firefighter's clothing are made were tested. Additionally, the importance of height on the possibility of sorption of PAH compounds on a given type of material was analyzed. Based on the results obtained, it was found that the type of material and the zone in which the clothing items are used are important in the sorption processes of pollutants. Data in this area may be important for taking further actions regarding the modification of materials used in special fire brigade clothing and in their cleaning processes.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

This concept paper explores possible collective identities for a future wildland fire workforce. Taking inspiration from the work of futurists who foresee an end to the dominant fire exclusion/suppression paradigm, and assuming an emerging fire restoration/resilience paradigm shift replaces it, the paper engages in speculative explorations of the process and product of this paradigm shift on future collective identities for a workforce doing ecological fire management. Social constructionist assumptions from symbolic interactionist sociological theory, Gramscian political theory's concept of hegemony, and New-Social-Movement theory's concept of collective identity all provide the intellectual foundations for the discussion. This concept paper argues that in order to actualize a paradigm shift, more than advances in scientific research or reforms of government policies will be required--the wildland fire community will need to become (or join) a social movement engaged in collective actions. An imaginary social movement, the "Greenfire revolution," is invented to help illustrate how the selected theories and concepts might apply in the social construction of ecological fire management and the collective identities of its future workforce.

Abstract Several studies have been conducted to strengthen weak road layers, regardless of whether they are un-der construction or are undergoing maintenance. Using substrates filled with different materials has proven effective for increasing the strength of these layers. In this study, I evaluated the coefficient of lateral soil pressure under various conditions when using reinforced and unreinforced piles filled with in-expensive material and the extent of their contribution to strengthening road layers. The results con-firmed that there was a difference in the coefficient of lateral soil pressure when the sand-filled piles were reinforced. The sand-filled piles were divided into several parts by arming. The maximum coeffi-cient of lateral soil pressure was 0.38 in the case of sand (1 mm) with reinforcement, whereas it was 0.29 in the same case without reinforcement as shown in Figure 1. The maximum coefficient of lateral soil pressure was 0.27 in the case of granite grain (2 mm) with reinforcement, whereas it was 0.17 in the same case without reinforcement. Moreover, the maximum lateral pressure coefficient was 0.26 in the case of granite grain (3 mm) with reinforcement, and it was 0.30 in the same case without reinforce-ment.

The fast decoding of low-density parity-check (LDPC) is crucial for its future applications. In this paper, we propose to use Early Termination (ET) and Force Convergence (FC) techniques to accelerate the decoding of two new local/global two-phases decoding algorithms to reduce the Globally Coupled (GC) LDPC codes. Specifically, ET is applied in the local decoding phase of two- phases decoding of GC-LDPC codes to skip the local decoding which is highly likely to fail and avoid the unnecessary iterations. FC is applied in global decoding phase where converged variable nodes are identified and removed from Tanner graph and the decoding can be speed up shrinking parity check matrices. Two variants are proposed for the ET operation in local decoding phase. ET-1 merely stops iteration if it meets the stopping criterion while in ET-1, the iteration number saved in local decoding is added up in global decoding to improve the decoding performance. The simulation results show that the ET-1-FC scheme can save up to 42% decoding time complexity in the low SNR region while keeping the error rate performance nearly unchanged, the ET-2-FC can improve the error rate performance by 0.18dB at bit error rate 0.001 or 0.23dB at frame error rate 0.1. In the waterfalling region of BER/FER curves, both schemes can save about 25% decoding time complexity.

In this study, unlike conventional methods for producing vanadium (3.5+) electrolyte by VOSO4 and V2O5, a batch-type hydrothermal reactor was used to produce a vanadium (3.5+) electrolyte for vanadium redox flow batteries through a reduction reaction. The starting material, V2O5, was mixed with different concentrations of citric acid (0.8M, 1.2M, 1.6M, 2.0M) as reducing agent and stirred using a hot plate at 90°C for 60 minutes to achieve complete dispersion in the solution. The resulting solution was then subjected to a hydrothermal reduction reaction in a furnace at 150°C for 24 hours to produce vanadium (3.5+). The mixed state of the produced vanadium (3+) and vanadium (4+) was confirmed using UV-vis spectroscopy. Electrochemical properties were investigated through CV analysis, confirming that the optimal concentration was 1.6M. Charge and discharge experiments were conducted to compare the current efficiency, energy efficiency, and voltage efficiency of the electrolyte prepared by the hydrothermal reduction process and the electrolyte prepared by VOSO4. As a result, the electrolyte produced through the hydrothermal reduction process showed improved performance in all efficiencies. The results shows that vanadium (3.5+) electrolyte could be easily produced through a reaction process using citric acid.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

The shift towards autonomous excavators in construction and mining is a significant leap towards enhancing operational efficiency and ensuring worker safety. However, it presents challenges such as the need for sophisticated decision-making and environmental perception due to complex terrains and diverse conditions. Our study introduces the E-GTN framework, a novel approach tailored for autonomous excavation that leverages advanced multisensor fusion and a custom-designed convolutional neural network to address these challenges. Results demonstrate that GridNet effectively processes grid data, enabling the reinforcement learning algorithm to make informed decisions, thereby ensuring efficient and intelligent autonomous excavator performance. The study concludes that the E-GTN framework offers a robust solution for the challenges in unmanned excavator operations, providing a valuable platform for future advancements in the field.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

Prescribed fire is increasingly utilized for conservation and restoration goals, yet there is limited empirical evidence supporting its effectiveness in reducing wildfire-induced damages to valued resources of significant worth—whether natural, cultural, or economic. This study evaluates the efficacy of prescribed fire in reducing wildfire severity to LANDFIRE-defined vegetation classes and valued resources impacted by the 2017 West Mims event. Wildfire severity, measured using the differenced normalized burn ratio (dNBR) index, was highly heterogeneous both within and between vegetation classes; however, profound differences between treated and untreated areas were evident. The beneficial effects of prescribed fire were most pronounced within ca. two-years post-treatment but remained evident beyond three-years relative to untreated areas. For example, actively managed areas that were treated with prescribed fire just one month prior to the West Mims event exhibited an 88% reduction in mean wildfire severity relative to unmanaged areas. When post-treatment duration reached 38 months, mean wildfire severity remained 17% lower than untreated areas. Findings from this study reveal significant reductions in both average and peak wildfire severities in areas treated with frequent fire, supporting burn rotations of one to two years to balance fuel reduction and ecological conservation.

Chaotic systems are systems whose results are sensitive to the initial conditions. Chaotic systems generally have nonlinearities that can be difficult to model. One example of a chaotic system with nonlinearities is the Lorenz system. The Lorenz system can be used to model weather, wind disturbances, and electronic circuit design, among other applications. In this manuscript, the Lorenz system is modeled and various control methods are applied in an effort to dictate the system’s state and rate trajectories. The combination of the linear feedback and nonlinear feedforward controllers can show over an 80% improvement in state trajectory errors when compared to the baseline run. However, the improved state trajectory performance comes at a cost of as much as 1800% error in the rate trajectories.

The increasing frequency and intensity of wildfires necessitate innovative solutions to enhance firefighting capabilities. This review provides a comprehensive evaluation of vehicles specifically designed for direct forest fire suppression, focusing on their speed of fire response, and encompasses both ground and aerial units. The study explores the functionality and speed capacity of various fire suppression vehicles, including fire trucks, firefighting aircrafts and helicopters, robotic firefighting vehicles and uncrewed aerial vehicles (UAVs). Key features such as mobility, water capacity, and advanced technologies including Artificial Intelligence (AI)-driven navigation and remote sensing capabilities are evaluated. The review also addresses the operational challenges these vehicles face in wildland environments. Additionally, it identifies emerging trends and innovations in fire suppression vehicle technology, offering insights into future developments that aim to enhance the effectiveness and safety of firefighting operations in forest fires. This overview aims to serve as a valuable resource for researchers, fire departments, and emergency response planners focused on advancing fire suppression strategies in forest.

Fires in houses are inevitable and they cause loss of life and major repair costs for the damage structure and contents. There is a clear need to prevent its ignition and spread to adjacent areas. This article presents the steps taken, namely: contacts, data collection, tests, analysis and conclusions regarding the accident resulting from the outbreak and spread of a fire, on December 25, 2020, in a traditional Portuguese house in Arganil, Portugal. The owners and the court requested to carry out an expert opinion by a person with specialized technical-scientific knowledge, which led to this work as an expert. the work consists of carrying out observations and data analysis. Then, the observed and analysed data were laboratory tested in order to consistently identify characteristics that lead to the ignition and propagation of the fire. This work identified construction problems, materials used and heat sources that are responsible for the accident. The conclusions may be used to avoid future incidents or accidents with houses of same construction type.

Keywords: Vascular Malformation, Diode Laser, Angioma, Blue light, Conservative

The aim of our study was a comprehensive comparative assessment of the effect of consumption of 1 and 2% cholesterol as part of a standard diet with and without regular moderate physical activity on the main biomarkers of lipid and cholesterol metabolism, as well as the intestinal microbiota of male Wistar rats. The animals were randomly divided into 5 groups according to body weight and Open Field test results: Control (n=10), 1% Chol (n=10), 2% Chol (n=10), 1% Chol + RUN (n=10) and 2% Chol + RUN. The cholesterol was additionally added in the amount of 1g or 2g/100g, respectively, to the diet of animals. The rats of experimental groups 1% Chol + RUN and 2% Chol + RUN were subjected to regular (2 days a week) physical activity on a Treadmill. In rats of four experimental groups, when compared to the Control, a response of 39 indicators was revealed. The largest number of changes in biomarkers - 29 (statistically significant, p

While laminar flow heat transfer and mixing in microfluidic geometries has been investigated experimentally, as has the effect of geometry-induced turbulence in microfluidic flow (it is well documented that turbulence increases convective heat transfer in macrofluidic flow), little literature exists investigating the effect of electrokinetically-induced turbulence on heat transfer at the micro scale. Using recently observed experimental data, this work employed computational fluid dynamics coupled with electromagnetic simulations to determine if electrokinetically-forced, low-Reynolds number turbulence could be observed in a rectangular microchannel with using Newtonian fluids. Analysis of the results was done via comparison to the experimental criteria defined for turbulent flow. This work shows that, even with a simplified simulation setup, computational fluid dynamics (CFD) software can produce results comparable to experimental observations of low-Reynolds turbulence in microchannels using Newtonian fluids. In addition to comparing simulated velocities and turbulent energies to experimental data this work also presents initial data on the effects of electrokinetic forcing on microfluidic flow based on entropy generation rates.

Quadruped robots possess significant mobility in complex and uneven terrains due to their outstanding stability and flexibility, making them highly suitable in rescue missions, environmental monitoring, and smart agriculture. With the increasing use of quadruped robots in more demanding scenarios, ensuring accurate and stable state estimation in complex environments has become particularly important. Existing state estimation algorithms relying on multi-sensor fusion, such as those using IMU, LiDAR, and visual data, often face challenges on non-stationary terrains due to issues like foot-end slippage or unstable contact, leading to significant state drift. To tackle this problem, this paper introduces a state estimation algorithm that integrates an Invariant Extended Kalman Filter (InEKF) with a disturbance observer, aiming at estimating the motion state of quadruped robots on non-stationary terrains. Firstly, foot-end slippage is modeled as a deviation in body velocity and explicitly included in the state equations, allowing for a more precise representation of how slippage affects the state. Secondly, the state update process integrates both foot-end velocity and position observations to improve the overall accuracy and comprehensiveness of the estimation. Lastly, a foot-end contact probability model, coupled with an adaptive covariance adjustment strategy, is employed to dynamically modulate the influence of the observations. These enhancements significantly improve the filter's robustness and the accuracy of state estimation in non-stationary terrain scenarios. Experiments conducted with the Jueying Mini quadruped robot on various non-stationary terrains show that the enhanced InEKF method offers notable advantages over traditional filters in compensating for foot-end slippage and adapting to different terrains.

As Li-ion batteries use is spreading, incidents in large energy storage systems (stationary storage containers, …) or in large-scale cell and battery storages (warehouse, recyclers, …), often leading to fire, are occurring on regular basis. Water remains one of the most efficient fire extinguishing agents for tackling those battery incidents and large quantities are usually necessary. Since bat-teries contains various potentially harmful components (metals and their oxides or salts, sol-vents…) and that thermal runway induced battery incidents are accompanied with complex and potentially multistage fume emissions (containing both gas and particles) the potential impact of fire run-off water on the environment should be considered and assessed carefully. The tests presented in this paper focus on the analysis of the composition of run-off waters used to spray NMC Li-ion modules under thermal runaway. It highlights that waters used for fire-fighting are susceptible to contain many metals, including Ni, Mn, Co, Li and Al mixed with other carbonaceous species (soot, tarballs) and sometimes undecomposed solvents used in the elec-trolyte. Extra-polation of pollutant concentrations compared with PNEC values showed that, for large scale incidents, run-off water could be potentially hazardous to the environment.

Background: Chronic lateral epicondylitis challenges the therapeutical approach; underlying mechanisms are incompletely understood; neuropathic pain and central and peripheral sensitization may explain the fact that botulinum toxin was found to play a role in pain and function management. Methods: We searched the literature for MeSH terms: lateral epicondylitis or synonyms and botulinum toxin. Results: We found 14 papers containing trials on botulinum toxin injection into the tendon or into the extensor muscles (particularly extensor carpi radialis brevis and extensor communis digitorum). We followed the administration pathways, doses, timing and side effects. Conclusion: With chronic course, the focus of the therapy shifts from the afflicted tendon to the inserting muscles, as muscle contracture may create a vicious loop to perpetuate and aggravate the disease. Doses, timing and side effects are discussed.

Nanocellulose (CNC) seems to be a promising surfactant, which, together with expandable graphite (EG), forms the essence of an effective natural-based fire retardant wood coating. In our research, the most suitable composition of the mixture was tested concerning good solubility, dispersion, and consistency. Favorable results were achieved with the formulation composed of a 4% CNC alkaline solution with 80 wt.% of selected EG. Subsequently, six different EG were used to prepare these wood fire retardant coatings. The effectiveness of treatments was verified using a test with a radiant heat source, where the test samples' relative weight loss, relative burning rate, and surface temperature during 600 sec were evaluated. All prepared formulations can be characterized as more or less equally effective. However, the best results were obtained with EG of GG 200 – 100 N, where the mass loss of the sample was 8.10 ± 1.24%. Very good results were also achieved by graphite 25 E + 180 HPH (8.70 ± 0.89%), which is similar to the previous one, even according to the microscopic assessment of the coating as well as the expanded layer. Graphite type 25 K + 180 (8.86 ± 0.65 %) shows the expanded layer's best cohesion, coating uniformity, and ease of application. The results of this work confirmed that the CNC coating itself has significant retardation effects.

In the present study, field observation wind data from the time of the wind turbine blade damage accident on Shiratakiyama Wind Farm were analyzed in detail. In parallel, high-resolution LES turbulence simulations were performed in order to examine the model’s ability to numerically reproduce terrain-induced turbulence. The comparison of the observed and simulated time series (1 second average values) from a 10 minute period from the time of the accident led to the conclusion that the settings of the horizontal grid resolution and time increment are important to numerically reproduce the terrain-induced turbulence that caused the wind turbine blade damage accident on Shiratakiyama Wind Farm. A spectral analysis of the same set of observed and simulated data revealed that the simulated data reproduced the energy cascade of the actual terrain-induced turbulence well.

Background:Caregiving for individuals with neurological disease involves providing physical, emotional, and social support, which can be a challenging and stressful experience. This study aims to compare the caregivers' burden, including the impact on mental and physical health, social support, and quality of life, in different neurodegenerative disorders. Methods:Fifty-five primary caregivers (F=41;mean age=53.07±12.29) of patients with Parkinson's Disease (PD=26), Multiple System Atrophy (MSA=16), and Amyotrophic Lateral Sclerosis (ALS=13), took part in the study. Standardized screening scales for the quality of life (EQ-5D/EQ-VAS and PQoL), levels of the caregiving burden (CBI and FSQ), and the assessment of the anxiety-depressive axis (HADS) were administered. Results: The mean CBI score was higher for caregivers of MSA patients (28.81±21.90) and ALS (25.15±16.23) than for caregivers of PD patients (16.08±10.34; p=0.036). Critical burden (cut-off>36) was present in the caregivers of MSA (31.3%), ALS (23.1%), and PD (19.2%) patients. Caregivers of patients with ALS had a worse perception of quality of life (EQ-5D total score) than caregivers of patients with MSA and PD (p

This paper explores Ghana's two-decade journey in developing a digital land information system (LIS), exemplified by Ghana Enterprise Land Information System (GELIS) and Enterprise Land Information System (ELIS). Despite advancements by Ghana’s Lands Commission, manual processes persist and coexist with digital ones. Our study uses a qualitative approach to assess the effectiveness of the LIS implemented in Accra. The study found that Accra’s LIS is highly aligned with clear institutional mandates, roles, and responsibilities as well as the availability of laws and policies to support analogue to digital conversion. Furthermore, a robust approach for protecting data, operating system and software underpins the system. Subsequently, the integration of a digital LIS has enhanced service delivery and accountability. Nonetheless, Accra’s LIS is still at the beginning of a comprehensive learning and development curve. To sustain the LIS requires furtherance in the implementation plan, funding, law implementation, ICT strategy, divisional integration, work processes, data quality, and communication strategy. These findings will inform the next steps of improvement for Accra's LIS and guide its nationwide scaling, contributing to discussions on technology acceptance dynamics in predominantly analogue environments.

Visualizing geo-spatial data embedded into a three-dimensional terrain is challenging. The problem becomes even more complex when uncertainty information needs to be presented as well. This paper addresses the question of how to visually communicate all three aspects: the 3D terrain, the geo-spatial data, and the data-associated uncertainty. We argue that visualizing all aspects with a high degree of detail will likely exceed the visual budget. Therefore, we propose a visualization strategy based on prioritizing a selected aspect and presenting the remaining two with less detail. We discuss various design options that allow us to obtain differently prioritized visual representations. Our approach has been implemented as a tool for rapid visualization prototyping in the context of avionics applications. Practical solutions are described for a use case related to the visualization of 3D terrain and uncertain weather data.

Forest fires can occur suddenly and have significant environmental, economic, and social consequences. Timely and accurate evaluation and prediction of their progression, particularly the spread speed in difficult-to-access areas, are essential for emergency management departments to proactively implement prevention strategies and scientifically extinguish fires. This paper provides a comprehensive analysis of advanced technologies for predicting forest fire spread in China and globally. Incorporating remote sensing (RS) technology and forest fire science as the theoretical foundation, and utilizing the Wang Zhengfei forest fire spread model as the technical framework, this study constructs a forest fire spread model based on remote sensing interpretation. The model optimizes the method for acquiring parameters and enhances algorithm accuracy. By considering regional landforms (ridge lines, valley lines, slopes) and vegetation coverage, this paper establishes visual interpretation markers for identifying hotspots within the spread model. Utilizing statistical data from pixels within the fire line zone transforms the methodology for predicting forest fire spread speed, resulting in greater accuracy compared to conventional fixed-point predictions. Finally, the model was applied to the case of a forest fire in Mianning County, Sichuan Province, China and verified using high-time resolution mid-infrared image data and previous research findings. The results demonstrate that the predicted fire spread area from this RS-enabled model is consistent with both high-time resolution geostationary satellite data and previous research outcomes, indicating high reliability. This model can provide crucial fire spread information to relevant emergency departments, enabling effective preemptive measures and scientific firefighting strategies.

Tunnel fires are generally detected using various sensors, including measuring temperature, CO concentration, and smoke concentration. To address the ambiguity and inconsistency in multi-sensor data, this paper proposes a tunnel fire detection method based on an improved Dempster-Shafer (DS) evidence theory for multi-sensor data fusion. To solve the problem of evidence conflict in DS theory, a two-level multi-sensor data fusion framework is adopted. The first level of fusion involves feature fusion of the same type of sensor data, removing ambiguous data to obtain characteristic data, and calculating the basic probability assignment (BPA) function through the feature interval. The second level fusion derives basic probability numbers from the BPA, calculates the degree of evidence conflict, normalizes to obtain the relative conflict degree, and optimizes the BPA using the trust coefficient. The classical DS evidence theory is then used to integrate and obtain the probability of tunnel fire occurrence. Different heat release rates, tunnel wind speeds, and fire locations are set, forming four fire scenarios. Sensor monitoring data under each simulation condition are extracted and fused using the improved DS evidence theory. The results show that the proposed improved DS evidence theory method detects the probability of fire occurrence in the four scenarios as 67.5%, 71.0%, 82.8%, and 83.5%, respectively, and identifies fire occurrence in approximately 2.4 seconds, an improvement of 64.7% to 70% over traditional methods. This demonstrates the feasibility and superiority of the proposed method, highlighting its significant importance in ensuring personnel safety.

Fire detection is crucial for ensuring human safety and minimizing property damage. By utilizing advanced technologies, we can identify fires early, before they escalate. Autonomous fire detection systems are particularly vital in high-risk areas with minimal human presence. To address this need, we propose an automated fire-detection model based on YOLOv8. We modified the architecture of YOLOv8 and achieved impressive performances. Through comprehensive analysis of different YOLO models and their predecessors, we identified and addressed substantial gaps in this field. Also, by augmenting the framework with additional capabilities, we surpassed previous models, enabling real-time fire detection. Our proposed model achieves impressive performances, with 98% accuracy in fire detection and 97.8% in smoke detection. Moreover, recall rates for fire and smoke are 97.1% and 97.4%, respectively, with a mean average precision (mAP) accuracy of 99.1% for both cases. Finally, we applied an explainable artificial intelligence technique to interpret our proposed model and its results. This study lays the foundation for future research aimed at enhancing fire detection efficiency. The reliability of our modified model presents promising opportunities for future advancements, ensuring increased effectiveness and precision in efficient fire detection.

Wildfires have always been a part of the history of Mediterranean forests. However, forest regeneration after a wildfire is not certain. It depends on many factors, some of which may be influenced by land management activities. Failure of regeneration will cause a regime shift in the ecosystem, reducing the provision of ecosystem services and ultimately leading to desertification. How can we increase Mediterranean forests’ resilience to fire? To answer this question, we did a literature review, investigating chains of processes that allow forests to regenerate (which we label “regeneration mechanisms”), and assessed the impact of selected management practices documented in the WOCAT database on the regeneration mechanisms. We identified three distinct regeneration mechanisms that enable Mediterranean forests to recover, as well as the time frame before and after a fire in which they are at work, and factors that can hinder or support resilience. The three regeneration mechanisms enabling a forest to regenerate after a fire consist of regeneration (1) from a seed bank; (2) from resprouting individuals; and (3) from unburned plants that escaped the fire. Management practices were grouped into four categories: (1) fuel breaks, (2) fuel management, (3) afforestation, and (4) mulching. We assessed how and under what conditions land management modifies the ecosystem’s resilience. The results show that land management influences resilience by interacting with resilience mechanisms before and after the fire, and not just by modifying the fire regime. Our analysis demonstrates a need for adaptive – i.e. context- and time-specific – management strategies.

Fire is a serious security threat that can lead to casualties, property damage, and environmental damage. However, despite the availability of object detection algorithms, challenges persist in detecting fires and smoke. These challenges include slow convergence speed, poor performance in detecting small targets, and high computational cost limiting deployments. In this paper, Fire smoke and human detection based on ConvNeXt and Mixed encoder (FCM-DETR), an end-to-end object detection algorithm based on Deformable DETR, is proposed. Firstly, we introduce ConvNeXt to take the place of Resnet, which greatly reduces the amount of computation and improves the ability to extract irregular flame features. Secondly, to effectively process multi-scale features, the original encoder is decoupled into two modules. Then Mixed encoder, an innovative encoder structure, is proposed, resulting in excellent performance of multi-scale fire and smoke features fusion. What can’t be overlooked is that the encoder block is compatible with any DETR-based models. Finally, the convergence speed is accelerated and the mean of average precision is improved by applying a novel loss function called Powerful IoU v2. The experimental results indicate that our model achieves the best detection accuracy compared to other models, with mAP reaching 66.7%, mAPs and Accuracyfire achieving impressive 50.2% and 98.05%, respectively.

The growing requirements regarding the safety of using polymers and their composites are related to the emergence of more effective, sustainable, and hazardous-limited fire retardants (FR). Significant amounts of FR are usually required to effectively affect the polymer burning behavior, while the knowledge of their recycling potential is still insufficient. At the same time, concerns are related not only to the reduced effectiveness of flame retardancy but, above all, to the potential deterioration of mechanical properties caused by the degradation of temperature-affected additives under processing conditions. This study describes the impact of four-time reprocessing of bio-based polyamide 11 (PA11) modified with an intumescent flame retardant (IFR) system composed of ammonium polyphosphate (APP), melamine cyanurate (MC) and pentaerythritol (PER) and its composites containing additionally short basalt fibers (BF). Composites manufactured by twin-screw extrusion were subjected to four reprocessing cycles by injection molding, comprehensively analyzing structural, mechanical, and fire behavior changes in each cycle. The obtained results confirmed the safety of using the proposed flame-retardant system for polyamide, processed under the recommended process parameters, without the risk of significant changes in the structure despite the partial increase in flammability caused mainly by the degradation of the polymer.

Background: This study stands as a pioneer in the histological evaluation of the biological behavior of a novel implant design featuring decompressive cervical blades. Hence, the aim of the present study was to evaluate the healing outcome in cortical regions at where decompressive protocols were adopted using implants equipped with blades. Materials and methods: Blades with varying diameters were integrated into the coronal portion of the implant to prepare the cortical region of rabbit tibiae. The blade diameters differed from the implant collar by the following amounts: control group (0 µm), +50 µm, and +200 µm. Results: No marginal bone loss was detected. Instead, all implants exhibited new bone formation in the coronal region. Complete closure was observed in the CG-0 group, as well as in the TG-50 and TG-200 groups, despite the presence of marginal gaps without primary bone contact at installation. In the apical region, most implants breached the cortical layer. Nevertheless, new bone formation in this region completely closed the osteotomy, effectively isolating the internal environment of the tibia from the external. Conclusions: The use of a blade attached to the implant body enabled precise preparation of the cortical layer, allowing for controlled decompression in the targeted area. This technique resulted in optimal osseointegration with no loss of marginal bone, and complete restoration of marginal gaps ranging from 0 µm to 200 µm.

There is an important complementarity between experimental methods for the study of high-temperature viscoelasticity in the time and frequency domains, that has not always been fully exploited. Here we show that parallel processing of forced-oscillation data and microcreep records, involving consistent use of either Andrade or extended Burgers creep-function models, yields a robust composite modulus-dissipation dataset spanning a broader range of periods than either technique alone. In fitting this dataset, the alternative Andrade and extended Burgers models differ in their partitioning of strain between the anelastic and viscous contributions. The extended Burgers model is preferred because it involves a finite range of anelastic relaxation times, and accordingly a well-defined anelastic relaxation strength. The new strategy offers the prospect of better constraining the transition between transient and steady-state creep, or equivalently, between anelastic and viscous behaviour.

Visualization of the seabed terrain is one of the key functions of marine geographic information system. The major challenge here is that the obtained data for seabed terrain usually consists of elevation and sediment only but does not include remote sensing images, which is important for ground terrain visualization, as they can be used as textures to reveal detailed information and achieve realistic visual results. Existing seabed terrain visualizing methods (including annotations, color-mapping, and texture-mapping) have limitations in reality and intuition, as they are inadequate to express the physical characteristics of sediment accurately. This paper presents a novel and advanced 3D visualization method of seabed terrain, which introduces the Physically Based Rendering (PBR) theory into the field of geographic visualization. We analyze the main categories of seabed sediments and their optical features respectively, then develop a procedural method to generate physically based rendering materials for different sediments. Then an enhanced bidirectional reflectance distribution function is employed to achieve accurate and intuitive terrain rendering. We also refine the texture sampling method and propose a procedural seabed objects generation method to construct a more natural and realistic undersea environment. Experimental results reveal our method can make good use of the limited seabed terrain data and get significant improvements in visual effect, which can help users to cognize and analyze the seabed geographic environment more accurately and intuitively.

The research was aimed at comparing the fire characteristics of different types of pepper in the context of designing explosion prevention. The following characteristics were studied: explosion pressure pmax and Kst at selected concentrations, ignition temperature of the deposited dust layer from the hot surface and minimum initiation energy. The comparison of the chemical properties of the used types of pepper was performed using TG/DSC. Results of the measurements suggest that different types of peppers exhibit different explosion characteristics. Each of the samples reached the maximum value of the explosion pressure, and their rate of pressure rise increased at different concentrations. The volume of the explosion chamber used also influenced the explosion characteristics. It is a consequence of the fact that the explosion characteristics strongly depend on the mechanism of action of a particular igniter. The minimum effect on the safety characteristics was observed when measuring the minimum initiation energy and the minimum ignition temperature of dust layer from the hot surface. The results of the measurements suggest that different types of peppers exhibit different explosion characteristics. This information should then be considered in explosion prevention.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

Grasping the spatial and temporal patterns of forest fires, along with the key factors that drive them and the ability to forecast such events accurately, is essential for the successful management of forests. In China's southern region, forest fires significantly endanger the ecological system, public safety, and economic well-being. Through the application of Geographic Information Systems (GIS) and LightGBM (Light Gradient Boosting Machine) model, this study investigates the determinants of fire incidents and formulates a predictive model for forest fire occurrences, alongside a zoning strategy, within the Central-South area. The results indicate: (i) Spatially, fire points exhibit significant clustering and autocorrelation characteristics; (ii) The Central-South Forest Fire Prediction Model shows exceptional accuracy, reliability, and predictive power, with high performance metrics across training and validation sets, including over 85% accuracy, precision, recall, and F1 scores, along with AUC values above 89%, underscoring its efficacy in forecasting forest fires and distinguishing between fire events; (iii) Throughout the year, forest fire risks in the Central-South region of China vary by region and season, with risk spikes from March to May in Guangdong, Guangxi, Hunan, Hubei, and Hainan. From June to August, localized risks are observed in Heyuan and Huangshi, while from September to November, an increase in risk is noted in Guangdong (Meizhou, Heyuan, Shaoguan), Guangxi (Nanning, Hezhou, Yulin), and Hunan (Binzhou, Yongzhou, Hengyang) due to cooler, drier conditions and leaf litter accumulation. From December to February, the risk continues in specific areas across Guangdong, Guangxi, Hunan, and Hubei.

Scedosporium species are human pathogenic fungi, responsible for chronic, localised, and life-threatening disseminated infections in both immunocompetent and immunocompromised individuals. Diagnosis of Scedosporium infections currently relies on non-specific CT, lengthy and insensitive culture from invasive biopsy, and time-consuming histopathology of tissue samples. At present, there are no rapid antigen tests that detect Scedosporium-specific biomarkers. Here we report the development of a rapid (30 min) and sensitive (pmol/L sensitivity) lateral-flow device (LFD) test, incorporating a Scedosporium-specific IgG1 monoclonal antibody (mAb), HG12, which binds to extracellular polysaccharide (EPS) antigens of between ~15 kDa and 250 kDa secreted during hyphal growth of the pathogens. The test is compatible with human serum, and allows the detection of the Scedosporium species most-frequently reported as agents of human disease (Scedosporium apiospermum, Scedosporium aurantiacum, and Scedosporium boydii), with limits of detection (LOD) of the EPS biomarkers in human serum of ~0.81 ng/mL (S. apiospermum), ~0.94 ng/mL (S. aurantiacum), and ~1.95 ng/mL (S. boydii). The Scedosporium-specific LFD (ScedLFD) test therefore provides a potential novel opportunity for the detection of infections caused by different Scedosporium species.

The Leave-One-Out (LOO) Green Fluorescent Protein (GFP) approach to biosensor design com-bines computational protein design with split protein reconstitution. LOO-GFPs reversibly fold and gain fluorescence upon encountering its target peptide, which can be redefined by computa-tional design of the LOO site. Such an approach can be used to create reusable biosensors for the early detection of emerging biological threats. Enlightening biophysical inferences for nine LOO-GFP biosensor libraries are presented, with target sequences from dengue, influenza, or HIV, replacing beta strands 7, 8 or 11. An initially low hit rate was traced to components of the energy function, manifesting in the over-rewarding of over-tight side chain packing. Also, screening by colony picking required a low library complexity, but designing a biosensor against a peptide of at least 12 residues requires a high complexity library. This double-bind was solved using a "piecemeal" iterative design strategy. Also, designed LOO-GFPs fluoresced in the unbound state due to unwanted dimerization, but this was solved by fusing a fully functional prototype LOO-GFP to a fiber-forming protein, Drosophila ultrabithorax, creating a biosensor fiber. One in-fluenza hemagglutinin biosensor is characterized here in detail, showing a shifted excita-tion/emission spectrum, a micromolar affinity for the target peptide, and an unexpected pho-to-switching ability.

Abstract: Wildfires in forest ecosystems exert substantial ecological, economic, and social impacts. The effectiveness of fire management hinges on precise pre‐fire risk assessments to inform mitigation efforts. This study aims to investigate the relationship between predictions from pre‐fire risk assessments and outcomes observed through post‐fire burn severity analyses. In this study, forest fire risk was assessed with the Fuzzy Analytical Hierarchy Process, in which fire behavior factors were used as input. The degree of burn was determined using the Random Forest method using 11519 training points and 400 test points on Sentinel‐2 satellite images in three different classes. According to the results obtained from 266 selected test points located within the forest boundaries, all primary factors showed an increased effect in areas with high burn severity. Climate, in particular, emerged as the most influential factor, accounting for 52% of the overall impact. However, in cases of high fire severity, climate proved to be the most effective risk factor, ac‐counting for 67%. It followed by topography with 50% accuracy at high fire intensity. In the risk assessment is based on the FAHP method, climate was assigned the highest weight value among other factors with 32.2%. Topography emerged as the second most effective risk factor with 27 %. To evaluate the results more comprehensively both visually and statistically, two regions with different stand canopy characteristics were selected within the study area. While high burn severity had the highest accuracy in Case 1 area, moderate burn severity had the highest in Case 2 area. During the days when the fire continued, the direction of spread was obtained from MODIS images. In this way, the fire severity depending on the direction of fire progression was also interpreted. Through an analysis of various case studies and existing literature, the research underscores both the strengths and limitations inherent in predicting forest fire behavior‐based pre‐fire risk assessments. Furthermore, it emphasizes the necessity of continuous improvement to increase the success of forest fire management.

In this paper is proposed an analytical technique which can be used to obtain the forced response of a cantilevered tube conveying fluid. Considering the pipe subjected to an arbitrary harmonic force either distributed or concentrated, an analytical solution is found using Green’s function method. The solution obtained of the closed form satisfies the differential equations in a classical sense. The presented method giving the exact solutions is more precise than the classical eigenfunction expansion or Galerkin’s method with no need to the eigenfunctions or eigenvalues.

Using lightweight fire-rated board (LFRB) presents cost-effective opportunities for various passive fire protection measures. The aim of the project is to develop a LFRB with enhanced fire resistance, acoustic properties, and mechanical properties. These properties were determined using the Bunsen burner, furnace, energy dispersive X-Ray, impedance tube instrument, and Instron universal testing machine. To fabricate the LFRBs, vermiculite and perlite were blended with flame-retardant bind-ers, and four types of LFRBs were produced. A fire test was conducted to compare the fire-resistance performance of the LFRBs with a commercially available flame retardant board. The B2 prototype showed exceptional fire-resistant properties, with a temperature reduction of up to 73.0 °C as compared to the commercially available fire-rated magnesium board. Incorporating nano chicken eggshell into the specially formulated flame-retardant binder preserved the LFRBs’ structural integrity, enabling them to withstand fire for up to 120 minutes with an equilibrium temperature of 92.6 °C. This approach also provided an absorption coefficient of α = 2.0, a high flexural strength of 3.54 MPa, and effective flame retardancy properties with a low oxygen/carbon ratio of 2.60. These results make the LFRBs valuable for passive fire protection applications in the construction and building materials industry.

Digital elevation models (DEMs) have a wide range of applications and play a crucial role in many studies. Numerous public DEMs, frequently acquired using radar and optical satellite imagery, are currently available; however, DEM datasets tend to exhibit elevation values influenced by vegetation height and coverage, which can compromise the accuracy of models in representing terrain elevation. In this study, we developed a digital terrain model for South America using a novel methodology to remove vegetation bias in the Copernicus DEM GLO-30 (COPDEM) model using machine learning, Global Ecosystem Dynamics Investigation (GEDI) elevation data, and multispectral remote sensing products. Our results indicate considerable improvements compared to COPDEM in representing terrain elevation, reducing average errors (BIAS) from 9.6 m to 1.5 m. Furthermore, we evaluated our product (ANADEM) by comparison with other global DEMs, obtaining more accurate results for different conditions of vegetation fraction cover and land use. As a publicly available and open-source dataset, ANADEM will play a crucial role in advancing studies that demand accurate terrain elevation representations at large scales.

The retrieval of tree height percentiles with satellite lidar waveforms over the mountainous ar-eas is greatly challenged due to slanted and rugged topographic relief of underlying ground. A novel algorithm is proposed to extract the height percentiles based on the target response waveform (TRW) that is resolved by using a Richardson–Lucy deconvolution algorithm with an adaptive iterative time. The height metrics of the energy percentiles of 25%, 50%, 75% and 95% for the cumulative TRW distribution are determined by their vertical distances relative to the ground elevation in this study. To validate the proposed algorithm, we select the received waveforms of the Global Ecosystem Dynamics Investigation (GEDI) lidar over the Pahvant Mountains of central Utah, USA. The results reveal that the resolved TRWs resemble closely to the actual target response waveforms from the coincident airborne lidar data, with the mean values of the coefficient of correlation, total bias and root mean square error (RMSE) taking val-ue of 0.92, 0.0813 and 0.0016. In addition, the accuracies of the derived height percentiles from the proposed algorithm have been greatly improved compared with the conventional Gaussian de-composition method and the slope-adaptive waveform metrics method. The RMSE values de-crease by the mean values of 1.96 m and 2.72 m, respectively. It demonstrates that the proposed algorithm has good potential in the extraction of forest structure parameter over rugged moun-tainous areas.

It is commonly recognized that a ship’s ability to maintain stability is dependent upon the way its loads are distributed. This means making sure the center of gravity is sufficiently low and evenly distributed. Yet when a ship encounters turbulent water with extremely large wave amplitudes, load distribution is a critical factor in determining how stressed the ship becomes. In particular, this article examines several methods for increasing the ship's longitudinal strength to prevent ship structural damage during hogging and sagging. This research presents a number of proposed techniques to enhance the longitudinal strength of cargo ships in order to guarantee minimal stress and deformation during sagging and hogging. The first method is the stern-to-bow use of curved support structures to increase the longitudinal strength of a cargo ship. And another way to stiffen the lateral plate is the proposed use of different designs of the side plate, such as wavy curves, stars, etc. To further boost the strength, the lateral plate upper part is suggested to curve upward. A numerical simulation using ANSYS of the stiffened plate when subjected to uniform load distribution and fixed support on either end shows that there is a decrease in deformation of the plate when we use wavy curved plates compared with those of the other plate stiffening methods used, and furthermore, curving the plate on top increases its strength during sagging as well as hogging. Finally, the use of a curved support structure further enhanced the overall longitudinal strength of the vessel.

Weather surveillance radars routinely detect smoke of various origin. Of particular significance to the meteorological community are wildfires in forests and/or prairies. For example, one responsibility of the National Weather Service in the USA is to forecast fire outlooks as well as to monitor wild fire evolution. Polarimetric variables have enabled relatively easy recognitions of smoke plumes in data fields of weather radars. Presented here are the fields of these variables from smoke plumes caused by grass fire, brush fire, and forest fire. Histograms of polarimetric data from plumes contrast these three cases. Most of the data are from the polarimetric Weather Surveillance Radar 1988 Doppler (WSR-88D aka Nexrad, 10 cm wavelength) hence the wavelength does not influence these comparisons. Nevertheless, in one case simultaneous observations of a plume by the operational Terminal Doppler Weather Radar (TDWR, 5 cm wavelength) and a WSR-88D is used to infer backscattering characteristic and hence sizes of dominant contributors to the returns. In addition, comparisons with observations by other investigators of plumes from urban area but at a 5 cm wavelength are made. To interpret some measurements Computational Electromagnetics (CEM) tools are applied.

The decay of the low-mode internal tide due to the superharmonic energy cascade is investigated in a realistically forced global Hybrid Coordinate Ocean Model (HYCOM) simulation with 1/25 degrees (4 km) horizontal grid spacing. Time-mean and depth-integrated supertidal kinetic energy is found to be largest near low-latitude internal tide generation sites, such as the Bay of Bengal, Amazon Shelf, and Mascarene Ridge. The supertidal kinetic energy can make up to 50% of the total internal tide kinetic energy several hundred kilometers from the generation sites. As opposed to the tidal flux divergence, the supertidal flux divergence does not correlate with the barotropic to baroclinic energy conversion. Instead, the time-mean and depth-integrated supertidal flux divergence correlates with the nonlinear kinetic energy transfers from (sub)tidal to supertidal frequency bands as estimated with a novel coarse-graining approach. The regular spaced banding patterns of the surface-intensified nonlinear energy transfers are attributed to semidiurnal mode 1 and mode 2 internal waves that interfere constructively at the surface. This causes patches where both surface tidal KE and nonlinear energy transfers are elevated. The simulated internal tide off the Amazon shelf steepens significantly near these patches, generating solitary-like waves in good agreement with Synthetic Aperture Radar (SAR) imagery. Globally, we find that regions of high supertidal energy flux also show a high correlation with observed instances of solitary nonlinear internal waves.

Coating a suitable material on substrate in thickness of nano to micro metres is a great interest for the scientific community. Hard coatings develop under the significant composition of suitable gaseous and solid atoms, where their energy and forced behaviors under certain transition states favour the binding. In the binding mechanism of gaseous and solid atoms, electron belonging to outer ring (filled state) of gaseous atom undertakes another clamp of energy knot belonging to outer ring (unfilled state) of solid atom. The set process conditions develop the coating of gaseous and solid atoms when energy of non-conservation is involved. Different natured atoms develop the structure in the form of hard coating by locating a common ground point, which is in their central ground points. Here, gaseous atoms increase the potential energy of electrons by decreasing levitational force (at electron level) in a controlled orientating manner, whereas solid atoms decrease the potential energy of electrons by decreasing gravitational force (at electron level) in a controlled orientating manner. Thus, hard coating is deposited under the oppositely switched energy and forced behaviors of different natured atoms. In TiN coating, Ti–Ti atoms bind due to the difference of expansion in their lattices when one atom is deposited and one is being deposited. So, one Ti atom just lands on the already landed Ti atom. While adhering N atom to Ti atom, it occupies the interstitial position in the Ti atoms. The rate of ejecting solid atoms depends on the type of source, parameters and a processing technique. In random arc-based vapor deposition system, depositing coating at substrate depends on several parameters. As per set conditions of the process, different natured atoms deposit at substrate surface to develop the structure of coating. In addition to intrinsic behavior of atoms, different properties of coatings materialised as per the nature of forces engaged under the involved energy. In developing hard coating of gaseous and solid atoms, an involved energy of non-conservation engages force of non-conservation, too. Hence, this study opens new avenues not only in the fields of hard coatings but also in the fields of functional coatings, medical and surgical implant coatings, protective and sensitive coatings, etc.

The purpose of this study was to investigate the relationship between clinical outcomes and lateral thrust before and after unicompartmental knee arthroplasty (UKA) using inertial measurement sensor units. Eleven knees were evaluated with gait analysis. The varus angular velocity was used to evaluate lateral thrust. The femoro-tibial angle (FTA) and hip-knee-ankle angle (HKA) were used to evaluate lower limb alignment, and Oxford Knee Score (OKS) and Japanese Orthopaedic Association Score (JOA) were used to evaluate clinical outcomes. The mean pre-UKA peak varus velocity was 37.1 ± 9.8°/sec, and that of post-UKA was 28.8 ± 9.1°/sec (p=0.00003). Assuming the definition of lateral thrust is when varus angular velocity is more than 28.1°/sec, 81.8% of patients had lateral thrust preoperatively, but this decreased to 55.6% postoperatively. Both OKS and JOA improved after surgery. In addition, HKA was -7.9° preoperatively and -5.8° postoperatively (p=0.024), and FTA was 181.4° preoperatively and 178.4° postoperatively (p=0.012). There was a positive correlation between postoperative JOA and FTA, indicating that changes in postoperative alignment affected clinical outcomes. This study quantitatively evaluated the disappearance of lateral thrust by UKA, and it found that the stability can be achieved by UKA for unstable knees with lateral thrust.

Background and objectives: As the oblique lateral interbody fusion at L5/S1 (OLIF51) and lateral corridor approach (LCA) have gained popularity, the understanding of precise vascular structure at L5/S1 level is indispensable. The objectives of this study were to investigate the vascular anatomy at L5/S1 level, and to compare the movement of vascular tissue between supine and lateral decubitus position using the intraoperative enhanced CT and MRI. Materials and Methods: A total of 43 patients who underwent either OLIF51 or LCA were investigated with the average age at surgery of 60.4 (37-80) years old. The preoperative MRI was taken to observe axial and sagittal anatomy of vascular position under supine position. The intraoperative vein-enhanced CT was taken just before incision in the right decubitus position, and compared to supine MRI anatomy. The iliolumbar vein appearance and its types were also classified. Results: The average vascular window allowed for OLIF51 was 22.8 mm and 34.1 mm at either L5 caudal endplate or S1 cephalad endplate level, respectively. It allowed for LCA was 14.2 mm and 12.6 mm at either level, respectively. The left common iliac vein moved 3.8 mm and 6.9 mm to right direction at either level from supine to right decubitus position, respectively. The bifurcation moved 6.3 mm to caudal direction from supine to right decubitus. The iliolumbar vein was located at 31 mm lateral from midline, and MRI detection rate was 52%. Conclusions: The precise measurement of vascular anatomy indicated that OLIF51 approach was the standard minimally invasive anterior approach for L5/S1 disc level compared to LCA, however, there were many variations in quantitative anatomy as well as significant vascular movements between supine and right decubitus position. In the clinical setting of OLIF51 and LCA surgeries, the careful preoperative evaluation and intraoperative 3D imaging are recommended for the safe and accurate surgery.

We present a near real-time solution for 3D reconstruction from aerial images captured by consumer UAVs. Our core idea is to simplify the multi-view stereo problem into a series of two-view stereo matching problems. Our method applies to UAVs equipped with only one camera and does not require special stereo-capturing setups. We found that the neighboring two video frames taken by UAVs flying at a mid-to-high cruising altitude can be approximated as left and right views from a virtual stereo camera. Leveraging GPU-accelerated real-time stereo estimation, efficient PnP correspondence solving algorithms and extended Kalman filter, our system simultaneously predicts scene geometry and camera position/orientation from the virtual stereo cameras. Also, this method allows user selection of varying baseline lengths, which provides more flexibility given the trade-off between camera resolution, effective measuring distance, flight altitude, and mapping accuracy. Our method outputs dense point clouds at a constant speed of 25 frames per second and is validated on a variety of real-world datasets with satisfactory results.

We describe an efficient approach to radiometrically flatten geocoded stacks of calibrated synthetic aperture radar (SAR) data for terrain-related effects. We use simulation to demonstrate that, for the Sentinel-1 mission, one static radiometric terrain flattening factor derived from actual SAR imaging metadata per imaging geometry is sufficient for flattening interferometrically compliant stacks of SAR data. We quantify the loss of precision due to application of static flattening factors, and show that these are well below stated requirements of change detection algorithms. Finally, we discuss the implications of applying radiometric terrain flattening to geocoded SAR data instead of the traditional approach of flattening data provided in the original SAR image geometry. The proposed approach allows for efficient and consistent generation of five different Committee of Earth Observation Satellites (CEOS) Analysis Ready Dataset (ARD) families - Geocoded Single Look Complex (GSLC), Interferometric Radar (InSAR), Normalized Radar Backscatter (NRB), Polarimetric Radar (POL) and Ocean Radar Backscatter (ORB) from SAR missions in a common framework.

Most real-time terrain point cloud rendering techniques do not address the empty space between the points but rather try to minimize it by changing the way how the points are rendered by either rendering them bigger or with more appropriate shapes such as paraboloids. In this work, we propose an alternative approach to point cloud rendering, which addresses the empty space between the points and tries to fill it with appropriate values to achieve the best possible output. The proposed approach runs in real time and outperforms several existing point cloud rendering techniques in terms of speed and render quality.

Objectives: To investigate the etiology of amyotrophic lateral sclerosis (ALS) in an adult female patient. Methods: We conducted trio genome sequencing on a 35-year-old woman with progressive weakness in her left upper limb, as well as on her parents. Prior to sequencing, we performed a comprehensive neurological work-up on the patient, including neurological exam, electrophysiology, biomarker assessment, and brain and spinal cord MRI. Results : The propositus experienced weakness and atrophy in her left hand 6 months before the evaluation. This was associated with brisk reflexes and Hoffman sign in the same arm. Electroneuromyography revealed lower motor neuron involvement in three body regions. Neurofilament light chains were elevated in her cerebrospinal fluid. Brain imaging showed asymmetrical T2 hyperintensity of the corticospinal tracts and T2 linear hypointensity of the precentral gyri. Genome trio sequencing identified a likely pathogenic de novo variant in the propositus’s KIF1A gene (NM_001244008.2): c.574A>G, p.(Ile192Val). Discussion: Pathogenic variants in the KIF1A gene have been associated with a wide range of neurological manifestations called KIF1A-associated neurological diseases (KAND). The present report describe a likely pathogenic de novo variant in KIF1A associated with ALS, expanding the phenotypic spectrum of KAND and our understanding of the pathophysiology of ALS.

Background. Amyotrophic Lateral Sclerosis (ALS) is a devastating disease involving motor neuron degeneration. The few drugs approved for treatment have at most a marginal benefit, and death usually occurs 2-5 years after diagnosis. Methods. A thorough manual examination of the relevant literature, covering over 35,000 papers. Results. Two major phenomena that are generally not known to clinicians were found. First, insulin signaling is impaired in ALS even in patients not diagnosed with diabetes (DB). Almost all studies that have explicitly tested insulin function in non-DB ALS patients using glucose tolerance tests (18 out of 20, 1964-2022, different groups) have found it to be impaired. Second, there is strong evidence for excessive insulin-independent glucose uptake (IIGU) in ALS. In addition, (i) early/late diabetes are associated with increased/decreased risk, respectively; (ii) insulin-based diabetes drugs are protective in ALS in large retrospective human studies; and (iii) strong animal and human evidence shows that insulin opposes all of the major pathological processes in ALS. Conclusion. Most ALS patients have insulin impairment, yet this is commonly not diagnosed, likely because excessive IIGU normalizes glucose levels. The impairment promotes disease progression. Late diabetes is associated with decreased risk because high glucose levels indicate non-excessive IIGU, and because diabetes drugs are protective. Insulin-based treatment (e.g., GLP1 agonists, insulin) is beneficial and can be disease-modifying in ALS and in frontotemporal dementia variants comorbid with ALS. ALS patients should be routinely tested for insulin function and treated if test results are positive.

Intense thermoacoustic oscillations may lead to severe deterioration due to the induced intolerable damage to combustors. A better understanding of unstable behaviors is important to prevent or suppress these oscillations. Active thermoacoustic coupling in practical combustors is caused primarily by two approaches: inherent turbulent fluctuations and the flame response to acoustic waves. Turbulent fluctuations are generally characterized by random noise. This paper experimentally expands on previous analytic studies regarding the influence of colored disturbances on the thermoacoustic response near the supercritical bifurcation point. Therein, a laboratory-scale Rijke-type thermoacoustic system is established, and both supercritical and subcritical bifurcations are observed. Then, Ornstein–Uhlenbeck (OU)-type external colored noise is introduced near the supercritical bifurcation point, and the effects of the corresponding correlation time τc and noise intensity D are studied. The experimental results show that these variables of the colored noise significantly influence the dynamics of thermoacoustic oscillations in terms of the most probable amplitude, autocorrelation, and correlation time. A resonance-like behavior is observed as the noise intensity or the autocorrelation time of the colored noise is continuously varied, which means that the coherent resonance occurs in the thermoacoustic system. Finally, when the system is configured closer to the stability boundary, the extent of the coherence motion is intensified in the stochastic system response. Meanwhile, the Signal to Noise Ratios (SNRs) of the colored-noise-induced response are found to become more distinguished, the optimal colored noise intensity decreases, and the optimal autocorrelation time increases. This provides valuable guidance to predict the onset of thermoacoustic instabilities.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

3D city models integrate heterogeneous urban data from multiple sources in a unified geospatial representation, combining both semantics and geometry. Although in the last decades, they are predominantly used for visualization, today they are used in a large range of tasks related to exploration, analysis, and management across multiple domains. The complexity of urban processes and the diversity of urban environment bring challenges to the implementation of 3D city models. To address such challenges, this paper presents the development process of a 3D city model of a single neighborhood in Sofia city based on CityGML 2.0 standard. The model represents the buildings in LOD1 with a focus on CityGML features of related to the buildings like building part, terrain intersection curve and address. Similar building models of 18 cities provided as open datasets are explored and compared in order to extract good modeling practices. As a result, workflows for generation of 3D building models in LOD1 are elaborated and improvements in the feature modeling are proposed. Two options of building model are examined: modeling of a building as a single solid and modeling of a building with separate building parts. Finally, the possibilities for visualization of the model in popular platforms such as ArcGIS Pro and Cesium Ion are explored.

In order to achieve the dual carbon goal and simplify the decarbonization process, a CO2 recovery process of the fire-flooding exhaust was designed. The process adopted the two-stage membrane separation method to recover CO2 and obtain high purity CO2 rich flow, and then through the mixed refrigerant liquefaction and rectification column, food grade liquid CO2 was obtained. HYSYS process simulation shows that for the fire-flooding exhaust with a flow rate of 1000 kg/h and a given composition, the process can achieve a CO2 recovery of 69.02%, total product sales S=2086.8 yuan/h, and specific power consumption of 2.818 kW∙h/kg. On this basis, a hybrid simulation platform of HYSYS & Matlab was established. Taking the specific power consumption of the product as the objective function, sequential quadratic programming (SQP) algorithm was adopted to optimize the process, and the optimized specific power consumption was reduced by 18.8%. Finally, by adjusting N2/CO2 components, the adaptability of the optimization condition was analyzed.

Annually, the oak forests of the Zagros Mountain chains, in western Iran and northeastern Iraq, face recurring challenges posed by forest fires, particularly in the Kurdo-Zagrosian forests situated in western Iran and northeastern Iraq. Assessing fire susceptibility relies significantly on vegetation condition. Integrating in situ data, Remote Sensing (RS) data, alongside the integration of Geographical Information Systems (GIS), presents a cost-effective and precise approach to capturing environmental conditions before, during, and after fire events, minimizing the need for extensive fieldwork. This study refines and applies the Zagros Grass Index (ZGI), a local vegetation index tailored to discern between grass-covered surfaces from tree canopies in Zagros forests, identifying the grass masses as the most flammable fuel type. Utilizing Moderate Resolution Imaging Spectroradiometer (MODIS) Normalized Difference Vegetation Index (NDVI) product as input, from 2013 to 2022, the ZGI aims to mitigate the influence of tree canopies, isolating NDVI values solely attributable to grass cover. By incorporating phenological characteristics of forest trees and grass species, the ZGI outperforms NDVI in mapping grass-covered areas that are crucial for fire susceptibility assessment in the study region. Results demonstrate a strong overlap between ZGI-based maps and recorded fire occurrences, validating the efficacy of the index in fire susceptibility estimation.

We study the enhancement of the elastocaloric effect in natural rubber by using forced air convection in order to favour heat extraction during the elongation stage of an stretching-unstretching cycle. Elastocaloric performance is quantified by means of the adiabatic undercooling that occurs after a fast removal of the stress, measured by infrared thermography. To ensure accurate measurements, spatial averages on thermal maps of the sample surface are performed since undercooled samples display heterogeneities caused by various factors. The influence of the stretching velocity and the air velocity is analysed. The results show that, given the fact that the stretching velocities should be high enough to improve the cooling power, there is an optimal air velocity that provides maximum adiabatic undercooling. Our experiments have also allowed us to characterise the dependence of the Newton heat transfer coefficient on the air convection velocity. We have shown that this coefficient may show an enhancement up to 600% for air velocities around 4 m/s.

This work focuses on forced combustion with regards to the relationship between vent mixer models and several injection locations in unheated supersonic flow. A plasma jet torch was used to ignite the hydrogen–air mixture in a laboratory-scaled combustor duct. The flow field of the combustion was visualized with pressure and gas-sampling measurements. The vent mixers indicate good dispersion characteristics of the mixture for both parallel and normal 1 injections. However, forced combustion is dominantly governed by the injection rate toward the plasma jet (hot source) because the combustible region is restricted under the cold main flow. For this reason, the parallel injection, which provides the hydrogen–air mixture directly toward the plasma jet, shows good combustion performance. The normal 1 injection interacted with the vent mixers and shows slightly good combustion performance. Lastly, the normal 2 injection is little affected by the vent mixers and has poor combustion performance.

Polyurethane is used extensively in the furniture industry, primarily in beds and sofas. There is a significant volume of research pertaining to the flammability of polyurethane materials, but very little regarding smoke toxicity. Given toxic fire effluents are a primary cause of injury and fatalities, more work needs to be done to test the toxicity of polyurethane materials and the fire retardants they are coated/bound with. The aim of the review is to provide a comprehensive analysis of the decomposition of polyurethane and discuss the development and application of modern fire retardants and their effect on smoke toxicity. This work then provides discussion on the challenges faced when attempting to quantify the toxicity of the effluent produced during combustion. Future work should aim to reduce the toxicity and flammability of polyurethane simultaneously by; reducing the pyrolysis of the polymer, preventing the escape of volatile products, reducing radicals within the system and lowering the temperature of the system. Before this can be achieved, a better understanding of smoke toxicity and the ability to test materials is needed.

Fires pose a significant threat to human life and property. An autonomous fire detection and fighting robot has the potential to mitigate the challenges associated with firefighting. This paper presents the implementation of an autonomous fire detection and fighting robot equipped with sensors, algorithms, and actuators to detect, locate, and suppress fires autonomously. The robot's mechanical and electrical components were designed, prototyped, and tested in a controlled environment to evaluate its ability to navigate through obstacles, detect fires, and suppress them autonomously. The results show that the robot effectively detects and suppresses fires, making it a promising solution for firefighting applications. The study contributes to the development of autonomous robots for firefighting, enhancing the safety of firefighters and the effectiveness of firefighting operations.

We developed a protein to rapidly and accurately diagnose Chagas disease, a life-threatening illness identified by the WHO as a critical worldwide public health risk. Complicating the current health situation are serological test limitations that contribute to most infected persons being unaware of their condition and therefore untreated. To improve diagnostic testing, we developed an immunological mimic of the etiological agent, Trypanosoma cruzi, by combining ten pathogen specific epitopes within the beta-barrel protein structure of Thermal Green Protein. The resulting multi-epitope protein, DxCruziV3, displayed high specificity and sensitivity as the antibody capture reagent in an ELISA platform with an analytical sensitivity that exceeds WHO recommendations. Within an immunochromatographic platform, DxCruziV3 showed excellent performance for the point of application diagnosis in a region endemic for multiple diseases, the municipality of Barcelos in the state of Amazonas, Brazil. In total, 167 individuals were rapidly tested using whole blood from a finger stick. As recommended by the Brazilian Ministry of Health, venous blood samples were laboratory tested by conventional assays for comparison. Test results suggest utilizing DxCruziV3 in different assay platforms can confidently diagnosis chronic infections by T. cruzi. Rapid and more accurate results will benefit everyone but will have the most noticeable impact in resource-limited rural areas where the disease is endemic.

Continual learning, a crucial facet of machine learning, involves the perpetual acquisition of valuable insights from incoming data, sans the necessity for full dataset access. Esteemed as a fundamental goal in artificial intelligence, continual learning grapples with an enduring challenge—catastrophic forgetting. A proficient model must exhibit adaptability for new data assimilation and robustness to retain existing knowledge. Class-incremental learning (CIL) aids the gradual integration of knowledge from newly introduced classes, forming a universal classifier. However, directly training the model with fresh class instances triggers a problem—forgetting distinguishing features of prior classes, causing a performance decline. Addressing such issues in machine learning, this survey aims to delineate significant challenges, outcomes, and recent advancements, including our contributions to CIL techniques, especially in image classification.

This research presents a comprehensive framework for efficiently generating forest fire datasets from Google Earth Engine data sources. The primary contribution of this work lies in providing a methodology to swiftly extract forest fire factors without the need for permissions or access to private datasets, rendering the dataset openly accessible and shared without barriers. Furthermore, given that the remote sensing data used is a global dataset, it can be applied in any region without restrictions. In this study, Peninsular Malaysia is chosen as a case study to demonstrate the framework's effectiveness. The generated dataset includes essential variables including the climate and environment, landcover, topography, and anthropogenic factors facilitating the analysis of fire occurrences. The methodology empowers data scientists, enabling them to leverage their analytical skills on the extracted dataset without requiring specialized remote sensing knowledge. Additionally, this study also showcases the adoption of large language models, specifically GPT-4 with the Noteable plugin, as a tool for conducting preliminary analyses on the generated dataset. Sample analyses reveal that several key features, including the KBDI, LST, PDSI, climate water deficit, and precipitation, significantly impact forest fire occurrences in Peninsular Malaysia. Despite the successful application of the GPT-4 with Noteable plugin, certain limitations and challenges are identified, highlighting the necessity for further validation of the tool's applicability and limitations. This study encourages future research to (1) adopt the proposed framework in other regions, (2) explore more detailed analyses encompassing all variables, and (3) leverage machine learning for advanced forecasting.

The development of synthetic biology has enabled us to make massive progress on biotechnology and to approach research questions from a brand new perspective. In particular, the design and study of gene regulatory networks in vitro, in vivo and in silico, have played an increasingly indispensable role in understanding and controlling biological phenomena. Among them, it is of great interest to understand how associative learning is formed at the molecular circuit level. Noticeably, mathematical models have been increasingly used to predict the behaviors of molecular circuits. The Fernando’s model, which is thought to be one of the first works in this line of research using the Hill equation, attempted to design a synthetic circuit that mimics Hebbian learning in the neural network architecture. In this article, we carry out in-depth computational analysis of the model and demonstrate that the reinforcement effect can be achieved by choosing the proper parameter values. We also construct a novel circuit that can demonstrate forced dissociation, which was not observed in the Fernando’s model. Our work can be readily used as reference for synthetic biologists who consider implementing the circuits of this kind in biological systems.

This article traces the origination, distribution, kinematics, function, and nature of alternative lateral horse gaits, i.e. intermediate speed lateral-sequence gaits involving the synchronization of ipsilateral limbs in the swing phase. Such alternative lateral horse gaits (namely, the running walk, rack, broken pace, hard pace, and broken trot) have been prized by equestrians for their comfort, and have been found in select horse breeds for hundreds of years and even exhibited in fossil equid trackways. After exploring the evolution and development of alternative lateral gaits via fossil equid trackways, human art and historical writings, and the genetics and history of modern horse breeds, functional and biomechanical reasons are offered for the genesis of these gaits. The article concludes by tracing similarities and differences between and within the expression of these alternative lateral gaits by various horse breeds. Fast and low-swinging hard pacing gaits are common in several horse breeds of East and North Asia, high-stepping rack and running walk gaits are often displayed in European and North and South American breeds, the broken pace is found in breeds of Central Asia, Southeast Asia, West Asia, Western North America, and Brazil in South American, and the broken trot occurs in breeds of North Asia, South Asia, and the Southern United States, and Brazil South America.

Motivated by important applications to the analysis of complex noise-induced phenomena, a problem of the constructive description of randomly forced equilibria for nonlinear systems with multiplicative noise is considered. Using apparatus of the first approximation systems, we construct an approximation of mean square deviations that explicitly takes into account the presence of multiplicative noise. This approximation is compared with the widely used approximation based on the stochastic sensitivity technique. The general mathematical results are illustrated with the example of the van der Pol oscillator with hard excitement.

Starting with a hypothetical geostrophic zonal current in an unbounded ocean, the investigation points out the response of this simple system to a thermal forcing, applied to the free surface and consistent with the maintenance of the geostrophic balance. The main result is the formation of a meridional component of the current, according to the Sverdrup relation, such that the full velocity vector rotates clockwise for heating and anticlockwise for cooling to adjust eventually in the initial zonal direction for large depths.

Amyotrophic lateral sclerosis (ALS) is a progressive neurodegenerative disease that affects both the upper and lower motor neurons in the nervous system, causing muscle weakness and severe disability. The progressive course of the disease reduces the functional capacity in the affected patients, limits daily activities and leads to complete dependence on caregivers, ultimately resulting in a fatal outcome. Respiratory dysfunction mostly occurs later in the disease and is associated with a worse prognosis. 46 participans were included in our study, with 23 patients in ALS group and 23 individuals in the control group. The ultrasound examination of the phrenic nerve (PN) was performed by two authors using a high-resolution "Philips EPIQ 7" ultrasound machine with a linear 4-18 MHz transducer. Our study revealed that the phrenic nerve is significantly smaller on both sides in ALS patients compared to the control group arba controls (p < 0.001). Only one significant study on PN ultrasound in ALS, conducted in Japan, also showed significant results (p < 0.00001). These small studies are particularly promising, as they suggest that ultrasound findings could serve as a additinioal diagnostic tool for ALS

This work attempts to answer in a clear way the following key questions regarding the optimal initialization of the Sysmon tool, towards the identification of Lateral Movement in the MS Windows ecosystem. First, from an expert’s standpoint and with reference to the relevant literature, what are the criteria of determining the possibly optimal initialization features of the Sysmon’s event monitoring tool, which are also applicable as custom rules within the config.xml configuration file? Second, based on the identified features, how can a functional configuration file, able to identify as many LM variants as possible, be generated? To answer these questions, we relied on the MITRE ATT&amp;CK knowledge base of adversary tactics and techniques, and focused on the execution of the nine commonest LM methods. The conducted experiments, performed on a properly configured testbed, suggested a great number of interrelated networking features, that were implemented as custom rules in the Sysmon’s config.xml file. Moreover, by capitalizing on the rich corpus of the 870K Sysmon logs collected, we create and evaluate in terms of TP and FP rates an extensible Python .evtx file analyzer, dubbed PeX, which can be used towards automatizing the parsing and scrutiny of such voluminous files. Both the .evtx logs dataset and the developed PeX tool are provided publicly for further propelling future research in this interesting and rapidly evolving field.

Using a three-dimensional, hydrostatic, primitive-equation ocean model, this study investigates the dynamics of lateral circulation in a partially stratified tidal inlet, the Barataria Pass in the Gulf of Mexico, over a 25.6-hour diurnal tidal cycle. Model performance is assessed against observational data. During flood tide, the lateral circulation exhibits the characteristics similar to that induced by differential advection, i.e., lateral flow consists of two counter-rotating cells and is convergent at the surface. The analysis of momentum balance indicates that, in addition to the pressure gradient and vertical stress divergence, nonlinear advection and horizontal stress divergence are also important contributors. During ebb phase, the lateral circulation is mostly eastward for the whole water column and persisting for almost the whole period. The surface divergence suggested by the differential advection mechanism lasts for a very short period, if it ever exists. The main momentum balance across most of the transect during ebb is between the along-channel advection of cross-channel momentum and pressure gradient. The sectional averaged lateral velocity magnitude during ebb is comparable to that during flood, which is different from the idealized numerical experiment result.

The terrain of Changbai Mountain has great influence on the distribution of atmospheric flows and the occurrence and development of precipitation. This study quantitatively analyzes the regional characteristic of topographic perturbations and the relationship between terrain, wind and precipitation in Changbai Mountain region, by using a spectral analysis of the two-dimensional discrete cosine transform. Three domains with relatively heavy summer precipitation are selected as the study region. The results indicate that the overall terrain of Changbai Mountain region exhibits anisotropic characteristics. The terrain spectra of domain B are less than those of domain A and C across the whole wavelength (λ) bands, indicating that the large-scale topographic perturbations of domain B are relatively weak. The largest topographic spectral peak of domain C shows the most pronounced undulation of terrain among the three domains. The dominant wavelengths of terrain height variance for domain A and C, both close to the respective maximum wavelengths, indicate more prominent large-scale topographic perturbations. For domain A, the variation of the precipitation spectra is consistent with that of the wind spectra at the wavelength bands of λ < 390 km, showing a high correlation between wind field and the occurrence of rainfall. The inverse relationship at larger wavelengths indicates that multiple factors contribute to the occurrence of rainfall. For domain B, there is consistency in the fluctuations of terrain spectra, precipitation spectra, and wind spectra at the wavelength bands of λ < 278.3 km, implying that the smaller-scale terrain has an important effect on the occurrence of summer precipitation. For domain C, the variations of terrain spectra, precipitation spectra, and wind spectra are almost consistent across the whole wavelength bands, indicating that the large-scale terrain and minor terrain both play a crucial role in atmospheric uplift and the occurrence and development of summer rainfall.

Water mist fire suppression technology has attracted an increasing interest from the field of fire protection services such as fire safety for buildings, ships, spacecraft, libraries and museums due to its non-toxic and high efficiency in the suppression of a wide variety of fires. To support the technological development of water mist fire suppression system and its application areas, this review introduces the concept of water mist system and discusses its suppression mechanisms in comparison with other fire protection systems. The recent application areas of water mist system are surveyed for class A fires involving combustible solid materials such as wood, paper and textiles; class B fires involving flammable liquids such as petrol, oils, lubricants, paints and waxes; class C fires involving flammable gasses such as natural gas and liquefied petroleum gas; fires involving electrical (class E) equipment such as computers and information technology facilities; and the class F fires involving flammable cooking oils and fats. Finally, the paper concludes the review by identifying the current research trends, and providing the future direction for water mist technology and applications.

Based on Chinese CDCP report on COVID-19, 14% of patients presented severe disease and 5% critical conditions. The average case-fatality rate was 2.3%, but mortality was as high as 49% in patients with critical illness. Serious life threatening thromboembolic complications have been found in 71·4% of non-survivors and micro/macro angiopathic coagulopathy has been found, also at autopsy, with highly increased neutrophil number, fibrinogen, concentrations of D-dimer and FDPs and NETs, ATIII decrease and normal number of platelets. A cytokine storm and interaction between inflammation and coagulation has been advocated as explanation of hypercoagulability. In this paper, it’s hypothesised that SARS-CoV-2 infection of alveolar cells induces recruitment of innate responder neutrophils, which release proteases and NETs inducing endothelial damage/endotheliopathy and imbalance of the four major proteolytic cascades (coagulation, complement, fibrinolysis and kallikrein) with prevalence of activators over inhibitors and consequent thrombotic complications. Platelets adhesion to damaged endothelium and the presence of ULVWF multimers, due to decreased ADAMTS13, contributes to the state of hypercoagulability. Neutrophil innate “unfriendly fire” response can be identified as the trigger of a “proteolytic storm”, responsible for subsequent well known prothrombotic condition and “cytokine storm”. The hypothesis explains also the pathology of recently described systemic “Kawasaki Disease like” vasculitis cases in Covid-19 young ill patients.

This article presents a combined route and path planning strategy to guide Skid-Steer Mobile Robots (SSMRs) in scheduled harvest tasks within expansive crop rows with complex terrain conditions. The proposed strategy integrates: i) a global planning algorithm based on the Traveling Salesman Problem under the Capacitated Vehicle Routing approach and Optimization Routing (OR-tools from Google) to prioritize harvesting positions by minimum path length, unexplored harvest points, and vehicle payload capacity, and ii) a local planning strategy using Informed Rapidly-exploring Random Tree (IRRT*) to coordinate scheduled harvesting points while avoiding low-traction terrain obstacles. The global approach generates an ordered queue of harvesting locations, maximizing the crop yield in a workspace map. In the second stage, the IRRT* planner avoids potential obstacles, including farm layout and slippery terrain. The path planning scheme incorporates a traversability model and a motion model of SSMRs to meet kinematic constraints. Experimental results in a generic fruit orchard demonstrated the effectiveness of the proposed strategy. In particular, the IRRT* algorithm outperformed RRT and RRT* with 96.1% and 97.6% smoother paths, respectively. The IRRT* also showed improved navigation efficiency, avoiding obstacles and slippage zones, making it suitable for precision agriculture.

Floods are one of the most wide-spread, frequent, and devastating natural disasters that continue to increase in frequency and intensity. Remote sensing, specifically synthetic aperture radar (SAR), has been widely used to detect surface water inundation to provide retrospective and near-real time (NRT) information due to its high-spatial resolution, self-illumination, and low atmospheric attenuation. However, the efficacy of flood inundation mapping with SAR is susceptible to reflections and scattering from a variety of factors including dense vegetation and urban areas. In this study, the topographic dataset height above nearest drainage (HAND) was investigated as a potential supplement to Sentinel-1A C-Band SAR along with supervised machine learning to improve the detection of inundation in heterogeneous areas. Three machine learning classifiers were trained on two sets of features SAR only (VV & VH) and VV, VH & HAND to map inundated areas. Three study sites along the Neuse River in North Carolina, USA during the record flood of Hurricane Matthew in October 2016 were selected. The binary classification analysis (inundated as positive vs. non-inundated as negative) revealed significant improvements when incorporating HAND in several metrics including classification accuracy (ACC) (+37.1%), true positive rate (TPR) (+51.2%), and negative predictive value (NPV) (+23.7%), A marginal improvement of +1.4% was seen for positive predictive value (PPV), but true negative rate (TNR) fell -15.1%. By incorporating HAND, a significant number of areas with high SAR backscatter but low HAND values were detected as inundated which increased true positives. This in turn also increased the false positives detected but to a lesser extent as evident in the metrics. This study demonstrates that HAND could be considered a valuable feature to enhance SAR flood inundation mapping especially in areas with heterogeneous land covers with dense vegetation that interfere with SAR.

The development of straddle-type monorail tour-transit systems (MTTSs) has received keen attention, raising the need for revisions on related design codes. This work presents a comprehensive assessment of the lateral stiffness limit of steel substructures in MTTSs. Firstly, a wind‒vehicle‒bridge coupling model was established, integrating multibody dynamics and finite element methods. This model was then validated against field test results, considering measured track irregularities as the excitation. Afterwards, a trend analysis and a variance-based sensitivity analysis was performed to investigate the effect of various factors on the dynamic response of MTTS. Referring to existing specifications, an evaluation index for the lateral stiffness of pier columns and track beams was proposed. Results indicate that the pier height significantly impacts the lateral displacement of the pier top, accounting for 87% of the first-order sensitivity index and 75% of the total sensitivity index. In comparison, the lateral stiffness of track beams contributes over 70% to the maximum lateral acceleration and displacement at the mid-span. Finally, the lateral limited values for the displacement at the pier top and the deflection–span ratio of the track beam were determined as 8.04 mm and L/4200, respectively. These findings can serve as valuable references for future research and designs in this field.

The Victorian Government Inquiry into wildfires that killed 173 people in 2009 has driven an Australian policy shift from self-evacuation or staying and defending a well-prepared property (‘go or stay’) to self-evacuation under catastrophic fire weather (‘leave early’). The Inquiry also led to the establishment of national ‘performance standards’ for Private Fire Shelters (PFS, that also known as bunkers). Nonetheless, incorporation of PFS into national bushfire policy remains embryonic with only Victoria having streamlined accreditation and planning approval processes. Arguments against PFS include potentially engendering complacency about preparing dwellings to survive fire and encourage risky behavior in response to a fire threat. Counteracting these arguments is research that shows that residents without PFS have low engagement with bushfire preparation and typically delay evacuation. In any case, because wildfire is unpredictable it is accepted that self-evacuation plans must have fallback positions that include sheltering ‘in place’ from the bushfire, making properly used and well maintained PFS an important element of bushfire safety. A less discussed barrier to PFS uptake outside Victoria appears to hinge on a lack of clarity about obligations for their design, certification, and consistency with planning approvals. The escalating Australian fire crisis demands much greater research and development in legal frameworks, policy and planning processes for PFS, as well as design and construction standards.

Kyrgyzstan, a landlocked nation in Central Asia, is characterized by its rugged mountainous terrain, which covers approximately 90% of its land area. This unique geography poses specific challenges related to climate vulnerability. To address these challenges, we propose a comprehensive approach that involves gathering meteorological data and making it accessible to decision-makers. By leveraging LoRaWAN communication technology, which efficiently transmits sparse and low-speed data over long distances while minimizing power consumption, we can enhance climate resilience. The Internet Society Kyrgyz Chapter, in collaboration with the International Centre for Theoretical Physics (ICTP) and the Central Asia Institute for Applied Geosciences (CAIAG), has initiated the installation of meteorological sensors and disaster mitigation devices, including river water level sensors, terrain moisture sensors, and tilt detectors. These sensors collect critical data, which is stored within the country on an ad hoc server. Stakeholders can access this data according to their specific requirements. This paper outlines the criteria for selecting the deployed equipment and provides details on the installation process at pilot sites, along with the challenges encountered during project execution.

Wind energy is a rapidly expanding renewable energy technique. Wind farm developers need to understand the interaction between wind farms and the atmospheric flow over complex terrain. Large-eddy simulations provide valuable data for gaining further insight into the impact of rough topography on wind-farm performance. In this research, we investigate the influence of spatial heterogeneity on wind turbine performance. We conducted numerical simulations of a 12×5 wind-turbine array on various rough topographies. First, we evaluated our LES method through mesh convergence analysis, using mean vertical profiles, vertical friction velocity, and resolved and subgrid-scale kinetic energy. Next, we analyze the effects of surface roughness and dispersive stresses on the performance of fully developed large wind farms. Our results demonstrate that the ground roughness element’s flow resistance boosts large wind-farm power production by almost 68% in fully aerodynamic rough surface compared to flat terrain. Dispersive stress analysis revealed that the primary degree of spatial heterogeneity in the wind farm is in the streamwise direction, which is the “wake-occupied” region, and the relative contribution of dispersive shear stress is almost 45% to the overall drag. We also observed that the power performance of the wind farm in complex terrain outperforms the drag. Our study has implications for improving the design of wind turbines and wind farms in complex terrain to increase their efficiency and energy output.

Accurate and prompt determination of fire types is essential for effective firefighting and reducing damages. However, traditional methods such as smoke detection, visual analysis, and wireless signals pose unavailability in identifying fire types. This paper introduces FireSonic, an acoustic sensing system that leverages commercial speakers and microphones to actively probe the fire using acoustic signals, effectively identifying indoor fire types. By incorporating beamforming technology, FireSonic first enhances signal clarity and reliability, thus mitigating signal attenuation and distortion. To establish a reliable correlation between fire types and sound propagation, FireSonic quantifies the Heat Release Rate (HRR) of flames by analyzing the relationship between fire heated areas and sound wave propagation delays. Furthermore, the system extracts spatiotemporal features related to fire from channel measurements. Experimental results demonstrate that FireSonic attains an average fire type classification accuracy of 95.5% and a detection latency of less than 400 ms, satisfying the requirements for real-time monitoring. This system significantly enhances the formulation of targeted firefighting strategies, boosting fire response effectiveness and public safety.

The rate of fires, and particularly residential-fires, is a serious concern in industrialized countries. However, there is considerable uncertainty regarding the reported numbers of residential-fire incidents as official figures are based on fires reported to fire response agencies only. This population-based study aims to quantify the total number of residential-fire incidents regardless of reporting status. The cohort comprised linked person-level data from Fire and Rescue New South Wales (FRNSW) and health system and death records. It includes all persons residing at a residential address in New South Wales, Australia, that experienced a fire between 1 January 2005 – 31 December 2014. Capture-Recapture method was used to estimate the underreporting number of residential fire-related incidents. Over the study period, 43,707 residential-fire incidents were reported to FRNSW and there were 2,795 residential fire-related health service utilization of which 2,380 were not reported. Using Capture-Recapture method, the total number of residential-fire incidents was estimated at 267,815 to 319,719 which is more than six times the official records. This study found that 15% of residential-fire incidents that were identified in health administrative dataset were reported. The residential-fire incidents that were not reported occurred mainly in socio-economically disadvantaged areas among the males and adults.

As broiler farming facilities have become larger and more concentrated in response to external environmental changes, there is a possibility of increased concentrations of fine dust and aerosols inside these facilities due to enclosure. In particular, workers are exposed to high concentrations of organic particulate matter and harmful gases while performing their tasks, and as they age, they become more vulnerable to respiratory diseases. It is essential to directly monitor the concen-trations to which workers are exposed, along with the spatial distribution of aerosols inside broiler house. In this study, we analyzed the regional aerosol concentrations using passive samplers in commercial tunnel-ventilated broiler farms. Simultaneously, we employed active samplers at the height of the workers' breathing zones to monitor real-time aerosol concentrations by particle size along their work routes. Spatial aerosol concentrations generally increased from the inlet to the exhaust in the breathing zone. The average aerosol concentrations were TSP -1,042 µg/m³, PM-10 718 µg/m³, and PM-2.5 137 µg/m³. To analyze the workers' exposure environments, we categorized the tasks in the barn into Static work period (SWP) and Moving work period (MWP) based on video analysis. The results showed that during MWP, fine dust concentrations exceeded the standards by up to 214%. Particularly, during MWP, the concentrations were 1.74 times higher for TSP, 1.40 times higher for PM-10, and 1.22 times higher for PM-2.5 compared to SWP. It was observed that during the movement of workers, physical generation of particles around 10 µm, such as feces, feed, and bedding, occurred due to the movement of chicken, which influenced the aerosol concentration.

Background: The lateral antebrachial cutaneous nerve (LACN) is the terminal sensory branch of musculocutaneous nerve and is rarely entrapped or injured. This study describes the electrodiagnostic (EDX) findings and etiologies of LACN neuropathy. Methods: This is a review of 49 patients with pain and/or paresthesia of the forearm who underwent EDX studies. The diagnosis of LACN neuropathy was based on clinical and sensory conduction abnormalities. Results: The most common etiology of LACN neuropathy was iatrogenic injury in 30 (61.2%) patients, primarily due to biceps tendon repair at the elbow (11 [36.7%]) and phlebotomy (5 [16.7%]. Fifteen (30.6%) patients sustained a non-iatrogenic injury at the proximal forearm/elbow, consisting of 6 (60%) laceration injuries and 5 (33.3%) stretch injuries. Four (8.2%) patients comprised the “other” etiology category, including 2 mass lesions causing LACN compression. Pain, paresthesia, and/or numbness in the LACN distribution were reported in 33 (67.3%), 27 (55.1%), and 23 (46.9%) patients, respectively. Hypoesthesia was detected in 45 (91.8%) patients, and dysesthesia in 7 (14.3%). The sensory nerve action potentials (SNAPs) of the LACN on the symptomatic side were absent in 44 (89.8%) patients. Of the 5 patients whose SNAPs of the LACN were detected, all had a decreased amplitude and 2 had increased sensory latency. Conclusion: The most common etiology for LACN neuropathy in this series was iatrogenic injury; repair of biceps tendon at the elbow was the most frequent provoking cause. Protection of the LACN during surgical procedures at the elbow and forearm is vital to prevent iatrogenic injury.

Amyotrophic lateral sclerosis (ALS) is a severe and incurable neurodegenerative disease, char-acterized by the progressive death of motor neurons, leading to paralysis and death. It is a rare disease distinguished by high patient-to-patient heterogeneity, making its study arduous and complex. Extracellular vesicles (EVs) emerged as an important player in ALS development. Thus, ALS phenotype-expressing cells can spread their abnormal bioactive cargos through the secretion of EVs, even at far distant tissues. Importantly, due to their nature and composition, EVs’ formation and cargo can be exploited for the better comprehension of this elusive disease and identification of novel biomarkers, as well as for potential therapeutic applications, such as those based on stem cell-derived exosomes. This review highlights the recent advances in the identification of the role of EVs in ALS etiopathology and how EVs can be promising new approaches for therapeutic strategies.

The gut microbiota has been suggested as an important factor in the pathogenic mechanisms of amyotrophic lateral sclerosis (ALS). This study aimed to investigate whether the intake of different kinds of dietary fiber was related to the disease progression rate (∆FS) and survival time. In total, 272 sporadic ALS patients diagnosed according to the revised EI Escorial criteria were recruited from March 2011 and were followed-up until the occurrence of events or the end of September 2020. The events included percutaneous endoscopic gastrostomy, tracheostomy, and death. Dietary fiber intake was calculated based on a 24-hour dietary recall and classified according to five major fiber-rich foods: vegetables, fruits, grains, legumes, and nuts/seeds. Among the total participants, the group with ∆FS values lower than the mean ∆FS (0.75) was noted in the highest tertiles of total and vegetable fiber intake. Participants with the highest tertile of vegetable fiber intake showed longer survival in the Kaplan–Meier analysis (p = 0.033). Notably, vegetable fiber intake was negatively correlated with pro-inflammatory cytokine (interleukin [IL]-1β, IL-6, and monocyte chemoattractant protein-1) levels in the cerebrospinal fluid. This study showed that vegetable fiber intake could influence the disease progression rate and survival time. Further clinical trials are needed to confirm whether dietary fiber supplementation improves the prognosis of ALS.

Beginning with navigation system design, this paper presents a comprehensive strategy for enhancing the search and rescue capabilities of agile mobile robots. Towards this, the autonomous ground vehicle (AGV) utilizes surface classification to determine and prioritize the terrain it is traversing. Our developed system design incorporates real-time terrain data with task objectives at a high level, ensuring that the robot can effectively navigate complex and ever-changing environments. This design, in conjunction with the introduction of a novel lightweight surface classification model, forms the basis of our adaptive terrain perception and decision-making systems, enabling robots such as Jackal to adapt rapidly and make the decisions necessary to complete the task. Subsequently, we exhaustively validated these systems through a series of extensive experiments in a variety of terrains, including normal and mixed terrains, demonstrating their robustness and efficacy in real-life situations.

The incidence of radiculopathy due to lumbar spinal stenosis has been on the increase in the aging population. However, patients aged 80 years hesitate to undergo conventional open surgery under general anesthesia because of the risk of postoperative morbidity and adverse events. Therefore, less invasive surgical alternatives are required for the elderly or medically handicapped patients. Transforaminal endoscopic lumbar lateral recess decompression (TELLRD) may be helpful for those patients. This study aimed to demonstrate the efficacy of TELLRD for treating radiculopathy in octogenarian patients. A total of 21 consecutive octogenarian patients with lumbar foraminal stenosis underwent TELLRD between January 2017 and January 2021. The inclusion criterion was unilateral radiculopathy, which stemmed from lumbar lateral recess stenosis. The pain source was verified using imaging studies and selective nerve blocks. Full-scale lateral canal decompression was performed using a percutaneous transforaminal endoscopic approach under local anesthesia. We found the pain scores and functional status improved significantly during the 24-month follow-up period. The clinical improvement rate was 95.24% (20 of 21 patients) with no systemic complication. In conclusion, endoscopic lateral recess decompression via the transforaminal approach is practical for octogenarian patients while reducing the medical risks of aggressive open surgery.

Rapid, accurate, and convenient diagnosis is essential for effective disease management. Various detection methods, such as enzyme-linked immunosorbent assay, have been extensively used, with lateral flow immunoassay (LFIA) recently emerging as a major diagnostic tool. Nanoparticles (NPs) with characteristic optical properties are used as probes for LFIA, and researchers have presented various types of optical NPs with modified optical properties. Herein, we review literature on LFIA with optical NPs for the detection of specific targets in the context of diagnostics.

Amyotrophic lateral sclerosis (ALS) is a fatal neuromuscular disease, characterized by progressive degeneration of upper and lower motor neurons in the cortex and spinal cord. Although the pathogenesis of ALS remains unclear, evidence on the role of the clonotypic immune system is growing. Adaptive immunity cells often appear changed in number or activation profile peripherally and centrally. However, their role in ALS appears conflicting. Data, from human and animal model studies, currently reported in literature show that each subset of lymphocytes and their mediators may mediate a protective or toxic mechanism in ALS, affecting both its progression and risk of death. In the present review article and attempt is made to shed light on the actual role of the cellular clonotypic immunity in ALS by integrating recent clinical studies and experimental observations.

Tracked vehicles play a vital role in accessing challenging terrains, offering stability, traction, and versatility for various applications, including deep-sea exploration. However, the seafloor and sediment contain valuable but poorly understood resources, making it a significant challenge for tracked vehicles during exploration. Consequently, it is imperative to conduct comprehensive studies before considering these terrains for off-road purposes. In this study, we developed a rigid, flexible track vehicle equipped with various sensors, focusing on monitoring pressure sinkage. Cohesive soils like Bentonite and Diatom soil, particularly when combined with sand and gravel mixtures, were used for the investigation and assessed for ground pressure, bearing capacity, and sinkage in rigid-flexible tracked vehicles on these characterized terrains under varying moisture conditions. Our findings indicated that increased moisture content in bentonite soil resulted in significantly higher track slippage and sinkage compared to diatomaceous earth soil. Regarding soil behavior, diatom soil exhibited notable compaction and sinkage characteristics compared to bentonite soil. These significant variations between these two soil types under changing moisture conditions highlight the complexity of such terrains. Therefore, understanding the soil and its physical properties is crucial before applying them to natural terrains. Furthermore, this study emphasizes the importance of precision in assessing the physical properties of natural terrains for the development of tracked vehicles for off-road exploration. This knowledge contributes to better vehicle design and a deeper comprehension of terrain mechanics.

This study examines the activities conducted at the archaeological site of Aptera in Crete, Greece. The research was part of the DIACHRONIC LANDSCAPES International Design Workshop, organized by the CAM (Center for Mediterranean Architecture), TUC (Technological University of Crete School of Architecture), and UNIFE (University of Ferrara Department of Architecture). This article outlines the methods used for data acquisition and processing on a territorial scale, which generated digital outputs necessary for the analysis and design phases of the workshop, as well as for further examination of the results. The collected data, obtained through low-cost aerial photogrammetric surveying and GNSS terrestrial coordinate detection, were integrated in a Structure from Motion workflow that led to the creation and exportation of various digital outputs, such as point clouds, DTM, DSM, orthophotos, and contour lines. An accuracy analysis was performed to evaluate the effectiveness and efficiency of the digital models compared to the implemented surveying strategies, including the Ground Control Point and Quality Check Point marker positioning strategy. The resulting digital models proved to be valuable assets for analysis and design within the workshop and provided insightful prospects for future research and territorial-scale projects.