Accurate pose estimation is a fundamental ability that all mobile robots must posses in order to navigate a given environment. Much like a human, this ability is dependent on the robot's understanding of a given scene. For Autonomous Vehicles (AV's), detailed 3D maps created beforehand are widely used to augment the perceptive abilities and estimate pose based on current sensor measurements. This approach however is less suited for rural communities that are sparsely connected and cover large areas. Topological maps such as OpenStreetMaps have proven to be a useful alternative in these situations. However, vehicle localization using these maps is non-trivial, particularly for the global localization task, where the map spans large areas. To deal with this challenge, we propose road descriptors along with an initialization technique for localization that allows for fast global pose estimation. We test our algorithms on (real world) maps and benchmark them against other map based localization as well as SLAM algorithms. Our results show that the proposed method can narrow down the pose to within 50 centimeters of the ground truth significantly faster than the state of the art methods.

Legionella bacteria can proliferate in poorly maintained water systems, posing risks to users. All Legionella species are potentially pathogenic but Legionella pneumophila (L. pneumophila) is usually the primary focus of testing. However, Legionella anisa (L. anisa) also colonises water distribution systems, is frequently found with L. pneumophila and could be a good indicator for increased risk of nosocomial infection. Anonymized data from three commercial Legionella testing laboratories afforded analysis of 565,750 water samples. Data covered July 2019 to August 2021, including the COVID-19 pandemic. Results confirmed L. anisa commonly colonises water distribution systems, being the most frequently identified non-L. pneumophila species. Proportions of L. anisa and L. pneumophila generally remained similar but increases in L. pneumophila during COVID-19 lockdown suggests static water supplies might favour its growth. Disinfection of hospital water systems was effective but re-colonization did occur, appearing to favour L. pneumophila, although L. anisa colony numbers also increased as a proportion of the total. While L. pneumophila remains the main species of concern as a risk to human health, L. anisa’s role should not be under-estimated, either as a potential infection risk or as an indicator of the need to intervene to control Legionella colonization of water supplies.

The object of this research is designing of new robot-to-robot communication system working in the middle of highway/roads to support mobile safety for approaching vehicles. The result of research project directs to a group of safety robot devices which induce a vehicle on a bypass route, as a vehicle guidance method using the same, and a vehicle safety guidance system. According to an embodiment of the present invention, a safety device includes a detector configured to detect a vehicle approaching the safety device, and an image projector configured to project an image onto a road surface approaching the vehicle when the detector recognizes an approach of the vehicle. It can include. According to the present invention, when it is necessary to guide the vehicle to the bypass route, the driver of the vehicle can grasp the detour route in time and move the vehicle to the next lane.

Abstract: Traffic collisions cause a huge problem of public health in low and middle income countries.. The safe system approach is generally considered as the leading concept on the way to road safety. Based on the fundamental premise that humans make mistakes, the overall traffic system should be ‘forgiving’. Sustainable safe road design is one of the key elements of the safe system approach. However, the road design principles behind the safe system approach are certainly not leading in today’s infrastructure developments in most LMICs. Cities are getting larger and road networks are expanding. In many cases, existing through-roads in local communities are up-graded, resulting in heavy traffic loads and high speeds on places, that are absolutely not suited for this kind of through-traffic. Furthermore a safe system would require that functional design properties of cars and roads would be conceptually integrated, which is not the case at all. Although advanced driver assistance systems are on their way of development for quite a long period, their potential role in the safe system concept is mostly unclear and at least strongly underexposed. The vision on future cars is dominated by the concept of automation. This paper argues that the way to self-driving cars, should take a route via the concept of guidance, i.e. vehicles that guide drivers, both on self-explaining roads and on more or less unsafe roads. Such an in-vehicle support system may help drivers to choose transport mode, route and speed, based on criteria related to safety and sustainability. It is suggested to develop a driver assistance system using relatively simple and cheap technologies, particularly for the purpose of use in LMICs. Such a GUIDE (Generic User Interface for Driving Evolution) may make roads self-explaining - not only by their physical design characteristics - but also by providing in-car guidance for drivers. In future the functional characteristics of both cars and roads should be conceptualized into one integrated safe system, in which the user plays the central role. As such GUIDE may serve as the conceptual bridge between vehicle and roadway characteristics. It is argued that GUIDE is necessary to bring a breakthrough in road safety developments in LMICs and also give an acceleration towards zero fatalities in HICs.

Precision metagenomic approaches using Oxford Nanopore Technology (ONT) sequencing has been shown to allow recovery of complete genomes of Escherichia coli O157:H7 from overnight enrichments of agricultural waters. This study tests the applicability of a similar approach for Cronobacter genome recovery from powdered infant formula (PIF) overnight enrichments, where Cronobacter typically dominates the overall microbiome (>90%). In this study, we aimed to test whether using ONT sequencing of overnight PIF enrichments could recover a completely closed Cronobacter genome for further genomic characterization. Ten PIF samples, each inoculated with different Cronobacter strains, covering Cronobacter sakazakii, C. muytjensii, C. dublinensis, C. turicensis, and C. universalis, were processed according to the Bacteriological Analytical Manual (BAM) protocol. qPCR was used for initial screening (detection and quantification) of the overnight enrichments and confirmed that the spiked PIF samples after the overnight enrichment have high levels of Cronobacter (107 to 109 CFU/mL). DNA from overnight PIF enrichments was extracted from the enrichment broth and sequenced using ONT. Results showed that ONT sequencing could accurately identify, characterize, and close the genomes of Cronobacter strains from overnight PIF enrichments in 3 days, much faster than the nearly two weeks required by the current BAM method. Complete genome recovery and species differentiation were achieved. This suggests that combining qPCR with ONT sequencing provides a rapid, cost-effective alternative for detecting and characterizing Cronobacter in PIF, enabling timely corrective actions during outbreaks.

Few studies have explored the gender wage gap among farmworkers, and there is a notable absence of research on how farm wages impact household welfare differently based on gender. This study aims to fill this gap by examining how farm wages affect gender disparities in household welfare among farmworkers in Nigeria. Using survey data from 720 farmworkers, we investigated gender-based differences in household welfare. Our approach combined parametric methods (Blinder-Oaxaca decomposition) to assess gender gaps in household welfare and non-parametric techniques (Propensity Score Matching, PSM) to estimate the effects of farm wages. The analysis reveals that female farmworkers experience significantly lower per capita food consumption expenditure (₦11,486.51 less) compared to their male counterparts. These disparities partly stem from differences in socioeconomic factors, job characteristics, and enterprise attributes between male and female farmworkers. The study underscores the role of farm wages in mitigating gender gaps in household welfare, demonstrating that farm wages have increased per capita food consumption expenditure for female farmworkers by ₦6,640.698. This finding highlights the potential of wage increases to enhance livelihoods, underscoring the importance of equitable wage policies in farming. Furthermore, our findings emphasize that the impact of farm wages on welfare varies with household characteristics, suggesting the need for targeted interventions tailored to enhance identified household attributes. Addressing these factors could effectively reduce gender inequalities in farm work and contribute to overall welfare improvements.

Predicting human trajectories poses a significant challenge due to the complex interplay of pedestrian behavior, which is influenced by environmental layout and interpersonal dynamics. This complexity is further compounded by variations in scene density. To address this, we introduce a novel dataset from the Festival of Lights in Lyon 2022, characterized by a wide range of densities (0.2-2.2 ped/m2). Our analysis demonstrates that density-based classification of data can significantly enhance the accuracy of predictive algorithms. We propose an innovative two-stage processing approach, surpassing current state-of-the-art methods in performance. Additionally, we utilize a collision-based error metric to better account for collisions in trajectory predictions. Our findings indicate that the effectiveness of this error metric is density-dependent, offering prediction insights. This study not only advances our understanding of human trajectory prediction in dense environments but also presents a methodological framework for integrating density considerations into predictive modeling, thereby improving algorithmic performance and collision avoidance.

Road cracks significantly affect the serviceability and safety of roadways, especially in mountainous terrain. Traditional inspection methods, such as manual detection, are excessively time-consuming, labor-intensive, and inefficient. Additionally, multi-function detection vehicles equipped with various sensors are expensive and not suitable for mountainous roads due to poor conditions. To address these challenges, this study proposes a customized Unmanned Aerial Vehicles (UAV) inspection system designed for automatic crack detection. The system focuses on enhancing autonomous capabilities in mountainous terrains by incorporating embedded algorithms for route planning, autonomous navigation, and automatic crack detection. The slide window method is proposed to enhance the autonomous navigation of UAV flights by generating path planning in mountainous roads. This method compensates for GPS/IMU positioning errors, particularly in GPS-denied or GPS-drift scenarios. Moreover, the YOLOv8 algorithm is introduced to conduct autonomous crack detection from UAV imagery in the offboard module. To validate our UAV inspection system's performance, we conducted several experiments to assess its accuracy, robustness, and efficiency. The experimental results demonstrate that our UAS inspection system accurately estimates the flight trajectory along the mountainous road for autonomous navigation. Furthermore, the experimental detection results also demonstrate that the YOLOv8 algorithm achieves higher recognition accuracy compared to the YOLOv5, and YOLOv7-tiny algorithms, exceeding 3.1%,and 6.8% of mAP, respectively. In summary, the UAV inspection system proposed in this study can provide a useful tool and technological guidance for the regular inspection of mountainous roads.

Underwater visual detection technology plays a pivotal role in fields such as marine exploration. With the increasing demand for underwater monitoring, the quest for efficient and reliable methods for underwater target recognition has become particularly significant. To address this requirement, this study developed an innovative underwater object detection architecture based on YOLOv8, named YOLOv8-MU, aimed at significantly enhancing detection accuracy.By integrating the LarK module proposed in UniRepLKNet to optimize the backbone network, YOLOv8-MU aims to achieve a larger receptive field without increasing the model’s depth. Further, this research introduces C2fSTR, an innovative method that combines Swin Transformer with the C2f module. Additionally, we have incorporated the SPPFCSPC_EMA module, which combines Cross-Stage Partial Fast Spatial Pyramid Pooling (SPPFCSPC) with attention mechanisms, significantly improving the detection accuracy and robustness of various biological targets. Moreover, by introducing a fusion block based on DAMO-YOLO into the neck of the model, we further enhanced the model’s capability in multi-scale feature extraction. Finally, the adoption of the MPDIoU loss function, designed around vertex distance, effectively tackles the challenges of localization accuracy and boundary clarity in underwater organism detection. Experimental results on the URPC2019 dataset demonstrate that the YOLOv8-MU model achieved an [email protected] of 78.4%, marking improvements of 5.6%, 1.1%, and 4.0% over YOLOv5s, YOLOv7, and YOLOv8n respectively, indicating the leading performance (SOTA) of this method. On the other hand, further evaluation on the URPC2020 dataset confirmed the generalization capability of the YOLOv8-MU architecture, with its [email protected] reaching 80.4%, surpassing various models including YOLOv5x and YOLOv8n, showcasing the wide applicability of our proposed improved model architecture.

The mortality of birds resulting from collisions and electrocutions with overhead lines, such as power lines, and phone line among others, has been implicated in the decline of various avian species globally. Specifically, overhead line collisions pose a significant threat to the conserva-tion of the Canarian houbara bustard (Chlamydotis undulata fuertaventurae), an endangered sub-species endemic to the Canary Islands. This study centres on the postmortem findings of Canarian houbara bustards that have collided with overhead lines, providing insights into the post-collision outcomes for these birds. A com-plete standardized necropsy of nine Canarian houbara bustards revealed that polytrauma was the cause of death in all cases. The most notable gross lesions associated with trauma included bone fractures, soft tissue lacerations, haemorrhages, luxations, and hemocoelom, with certain body regions being more frequently affected. Histopathology, immunohistochemistry, and en-tomology analysis confirmed that numerous birds survived the initial trauma, exhibiting varia-ble survival intervals before succumbing to their injuries. We concluded that when a houbara bustard collide with an overhead line it frequently survives the initial trauma. The histopathology, immunohistochemistry, or entomologic analysis may be helpful to approximate the timing interval between trauma and death.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

This research aimed to study and compare prevalence of work-related musculoskeletal (MSK) problem and perceived discomfort among port crane operators consisting of quay and rubber tyred gantry (RTG) cranes working in the Laem Chabang Deep-sea Port, Thailand. Direct interviews for a cross-sectional analysis was selected for this unique job with a small amount of sample size. A standardized modified version of the Nordic Musculoskeletal Questionnaire (NMQ) was lunched for 26 male participants, consisting of 11 quay and 15 RTG, where a priori power analysis using G*Power suggested the minimum as 24 for the hypothesis test. Socio-demographic characteristics showed no significant difference among them. The NMQ revealed lower back as the highest prevalent body part (76.9%) followed by neck, shoulders and upper back at the same percentage (23.1%) for all port crane group, with up to 96.2% reporting MSK problem over the past 12 months. And Borg scale rating, assessing the perceived discomfort, revealed lower back with the highest score (2.38) followed by upper back (0.65), shoulders (0.54) and neck (0.5). Remarkably, the comparation between the quey and RTG crane operators on the MSK prevalence (χ2 test) and perceived discomfort levels (Kruskal-Wallis test), regarding different 9 body parts, revealed a significant difference between the two on upper back with quay crane having more problem than the RTG at p < 0.05. while the rest of them were mainly in the same direction. MSK contributors such as: working awkward posture, mental stress, height, trolley distance and vibration are considerably the main causes of this. However, the larger in scale of exposure to those for the quey crane compared to the RTG might have led to the distinguishing MSK problem found in this study which require thoroughly deliberation for the particular solutions.

This study aimed to develop a state-of-the-art method for assessing chemical risks. The method combined desk research findings and the authors' practical knowledge to identify the major shortcomings in performing risk assessments at the workplace. Data were collected from nine SMEs across three sectors: agriculture, laboratory research, and conservation and restoration laboratories. The results of the discussions with the workers and on-site observations were used to develop the method to assess chemical risks. The method uses numerical factors to account for the level of conformity and the duration of exposure to support an estimation of the probability of an incident. The developed method was designed to enhance risk assessment practices and tackle common issues encountered by enterprises, including SMEs.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Insulin-like Growth Factor 2 mRNA binding Protein 1 (IGF2BP1) is a promising candidate gene for influencing economic traits in livestock and poultry. The second intronic region of IGF2BP1 is closely related to growth traits, although the exact mechanism remains unclear. The preliminary resequencing results of goats in our laboratory demonstrated that the IGF2BP1 gene region was subject to strong selection, then we selected multiple single nucleotide polymorphisms (SNPs) to identify. Seven SNPs were located in the conserved region of the second intron, and their functions and relationship with growth traits require further clarification. This study selected 348 Nanjiang Yellow goats as experimental subjects, and chose Time of Flight Mass Spectrometer (MALDI-TOF) as the main method. Our results showed that six SNPs were significantly correlated with the growth traits of the Nanjiang yellow goat by association analysis. Among them, the rs652062749(A>G) was identified as the primary locus affecting the later stage of growth traits of Nanjiang yellow goat. Moreover, there was a strong linkage among three SNPs, and the rs638185407 (T>A) mutant type was observed to increase the luciferase activity in H293T cells extremely significantly. The TTAACT, TTCCCC, and ATCACT combination genotypes were dominant combination genotypes, which provided theoretical references for further genetic co-breeding. The results of our study demonstrate the potential role of the IGF2BP1 gene as a functional genetic marker in the breeding programs of Nanjiang Yellow goats.

Exoskeleton technology has been shown to be useful for individuals with spinal cord injury (SCI), potentially facilitating their recovery of motor function and social reintegration. However, studies on the safety and usability of exoskeletons are limited. This study aimed to design a powered exoskeleton for SCI and evaluate its safety and usability. Ten healthy adults participated in this study. The prototype exoskeleton featured an adjustable frame, computer-controlled hip and knee joint actuators, and a gait-trigger sensor. The experimental actions included walking, standing, and sitting, with and without the prototype. Safety outcomes included adverse events, vital signs, numerical rating scale (NRS) scores for pain, discomfort, and fatigue, and prototype-human body clearance. Usability outcomes included donning and doffing times, subjective ratings, gait speed, stride length, and kinematic parameters of hip and knee joint angles. Safety outcomes showed no serious adverse events, stable vital signs, minimal NRS scores, and acceptable clearance. Usability outcomes showed high efficiency and received positive ratings. Kinematic parameters showed significant positive correlations between normal walking and walking with the prototype for both hip and knee joint angles, confirming its effectiveness in assisting walking. However, further device improvements and gait parameter tuning are necessary for future clinical application.

This paper reports on the optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation systems for cattle farming in rural areas of Bangladesh. Bangladesh is a lower middle-income country with declining rates of poverty among its 160 million people due to persistent economic growth in conjunction with balanced agricultural improvements. Most of the rural households adopt a mixed farming system by cultivating crops and simultaneously rearing livestock. Among the animals raised, cattle are considered as the most valuable asset for the small/medium-scale farmers in terms of their meat and milk production. Currently, along with the major health issue, the COVID-19 pandemic is hindering the world’s economic growth and has thrust millions into unemployment; Bangladesh is also in this loop. However, natural disasters such as COVID-19 pandemic and floods, largely constrain rural smallholder cattle farmers from climbing out of their poverty. In particular, small and medium-scale cattle farmers face many issues that obstruct them from taking advantage of market opportunities and imposing a greater burden on their families and incomes. An appropriate measure can give a way to make those cattle farmers’ businesses both profitable and sustainable. Optimization of thin-film coating assisted self-sustainable off-grid hybrid power generation system for cattle farming is a new and forward-looking approach for sustainable development of the livestock sector. In this study, we design and optimize a thin-film coating assisted hybrid (photovoltaic-battery-generator) power system by using the Hybrid Optimization of Multiple Energy Resources (HOMER, Version 3.14.0) simulation tool. An analysis of the results has suggested that the off-grid hybrid system is more feasible for small and medium-scale cattle farming systems with long-term sustainability to overcome the significant challenges faced by smallholder cattle farmers in Bangladesh.

European strategic policy directions towards a sustainable blue economy have strengthened interest in maritime investments, thus increasing sectoral competition for marine space. Emerging repercussions out of such a rising interest need to be handled by Marine Spatial Planning (MSP) as a means for: properly allocating marine space to diverse uses; managing conflicts and promoting synergies among them; and pursuing a multi-use perspective of this space. A critical stage of each MSP exercise is the exploration of land-based spatial/developmental directions and their current or potential repercussions in the marine environment in order for constraints but also perspectives in policy choices/maritime uses in the MSP context to be featured; and attainment of a successful coherence or coordination between land and marine spatial/developmental policies to be ensured, by analyzing Land-Sea-Interaction (LSI) and embedding it in the MSP. The latter is the focus of this paper aiming to illuminate critical issues emerging from land-based (terrestrial) policy frameworks for feeding MSP endeavors; and is accomplished in the Northern Aegean Sea, Greece. Towards this end, a multilevel approach is adopted, delving into diverse policy contexts at the local, regional and national/European level and aiming to attain more informed MSP decisions in the specific study region.

Bacteriophages (phages) are potential alternatives to chemical antimicrobials against pathogens of public health significance. Understanding the diversity and host specificity of phages is important for developing effective phage biocontrol approaches. Here, we assessed the host range, morphology, and genetic diversity of eight Salmonella enterica phages isolated from a wastewater treatment plant. The host range analysis revealed that six out of eight phages lysed more than 81% of the 43 Salmonella enterica isolates tested. The genomic sequences of all phages were determined. Whole genome sequencing data (WGS) data revealed that phage genome sizes ranged from 41 to 114 kb with GC contents be-tween 39.9 and 50.0 %. Two of the phages SB13 and SB28 represent new species Epsep-timavirus SB13 and genera Macdonaldcampvirus, respectively as designated by the In-ternational Committee for the Taxonomy of Viruses (ICTV) as per genome based taxonomic classification. One phage (SB18) belonged to the Myoviridae morphotype while the re-maining phages belonged to the Siphoviridae morphotype. The gene content analyses showed that none of the phages possessed virulence, toxin, antibiotic resistance, type I-VI toxin-antitoxin modules or lysogeny genes. Three (SB3, SB15 and SB18) out of the eight phages possessed tailspike proteins. Whole genome-based phylogeny of the eight phages with their 113 homologs revealed three clusters A, B, C and seven subclusters (A1, A2, A3, B1, B2, C1 and C2). While cluster C1 phages were predominantly isolated from animal sources, cluster B contained phages from both wastewater and animal sources. The broad host range of these phages highlights their potential use to control the presence of S. enterica in foods.

Bigeye grunt Brachydeuterus auritus is an important economic species in the waters off Sierra Leone in West Africa, with great ecological value. Based on the survey data of bottom trawl nets from 6 voyages from 2019 to 2021, the body weight-length relationship (WLR), as well as their relative fatness, were studied in depth using the method of body length and its corresponding mean body weight. This study fitted the WLR of bigeye grunt by gender, calculated its fullness, and analyzed the influence of environmental factors. The results showed that month and gender had a significant impact on body length and weight distribution (P<0.01). There was a highly significant negative correlation (P<0.01) between the condition factor (a) and the allometric factor (b) in the WLR, and salinity significantly affects b (P<0.05). The (lga)/b ratio was less affected by environmental factors which may be related to the body size and density of the fish. The difference in b between male and female populations was extremely significant (P<0.01). The relative fatness had significant seasonal variation characteristics, with highly significant effects of sex and body length (P<0.01). With increasing body length, the relative fatness showed two types of changes, continuously increasing and first increasing then decreasing, with salinity and b significantly affecting the type of change (P<0.05) and depth having a highly significant effect (P<0.01). The bigeye grunt off the coast Sierra Leone exhibited significant seasonal growth characteristics, with significant differences in growth characteristics between male and female individuals. This study suggested that salinity may be the main factor affecting its growth and development. In addition, this study hypothesised that the peak breeding season may occur during the dry season, beginning in December and ending before April of the following year. The study provides updated and more comprehensive insights into the biology and ecology of the bigeye grunt offshore Sierra Leone, West Africa, which can provide scientific basis for its resource assessment, development and utilization, and resource management.

Background: Land use and land cover change (LULCC) in the Ruhuhu River Sub-Basin (RRSB), a crucial watershed within the Lake Nyasa Basin in Tanzania, poses a significant threat to water resource sustainability and ecological integrity. However, a lack of comprehensive data on long-term LULCC trends has hindered effective conservation efforts. Methods: This study utilized Landsat 5 TM and Landsat 8 OLI data within Google Earth Engine to quantify LULCC dynamics from 1990 to 2023. Six land cover classes were analyzed: water, forest, barren land, grassland, shrubland, and farmland. Results: Results revealed a substantial decline in forest cover (56.92% to 28.60%), primarily converted to farmland (2.99% to 20.22%). Shrubland expanded initially but then declined, while barren land steadily increased. These changes have profound implications for water resources, biodiversity, and ecosystem services within the RRSB and the broader Lake Nyasa Basin. Conclusions: This research highlights the urgency of implementing sustainable land management practices to mitigate the adverse impacts of LULCC in the RRSB. The high classification accuracies achieved (90.9% to 98.7%) validate the robustness of the methodology. This study provides crucial insights for policymakers, land managers, and conservation practitioners, emphasizing the need for targeted interventions to promote sustainable land use and ensure the long-term resilience of the RRSB ecosystem.

Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. The tests were conducted for three sandstone varieties: Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching, however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities, as well as that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives.

In the quest for more sustainable urban landscape development, the concept of ‘green infrastructure’ (GI) has become central in policy documents and as a multifunctional general planning tool. GI is not however a simple and unambiguous solution. While there in policy documents are claims for more and connected GI, actual urban development takes another direction. The densifying imperative is hard to combine with an increased and more connected GI. This paper argues for a critical and diversified approach to the concept of GI, to facilitate its implementation in urban planning and management. While GI most often is seen as a common asset and a public good, the actual land use negotiations and management responsibilities cannot be limited to a public service discourse, but should address more clearly a variety of actors. Linguistic as well as spatial definitions of the two relevant dichotomies of ‘green-grey’ and ‘public-private’ are crucial in GI location, design, construction and management, it is argued. Overarching representations of GI will be needed, but also – and linked to it – a spatial storm water plan and an overall plan for public space. The development over time will need an intersectorial implementation and management program. Thus some of the GI intentions may be implemented in planning processes, some through reorganisation and redesign of public space, and some by agreements with landowners.

The conversion of caatinga vegetation areas into pastures in the Brazilian semiarid region has depleted soil fertility due to degradation. The natural regeneration of the caatinga has been the alternative adopted to restore soil fertility. However, the real effectiveness of this practice in re-covering organic carbon (SOC) and nutrient stocks is unknown. This work evaluated the effect of natural regeneration of the caatinga vegetation on the restoration of levels and stocks of SOC, N, and P as a strategy to maintain the sustainability of the environment. We collected soil samples every 5 cm, up to 20 cm deep, in areas of degraded pasture, caatinga in regeneration (10 years), and regenerated caatinga (35 years) to evaluate the levels and stocks of SOC, N, and P. The depth sig-nificantly affects the levels and stocks of SOC, N, and P. Stocks and levels of SOC, N, and P were higher in regenerated caatinga > regenerating caatinga > degraded pasture. The regenerated caatinga increased SOC, N, and P stocks by 115%, 110%, and 117%, respectively, compared to the degraded pasture. Although 35 years of regeneration of the caatinga has improved soil fertility, the levels and stocks of SOC, N, and P remain low.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Many types of banana (Musa spp.)—one of the most economically important horticultural crops—exist, and their ploidy (diploid, triploid, and tetraploid, usually) and genome types (containing A or/and B genome in most cases) differ. At present, observation and genome type detection are commonly used to identify banana germplasm resources. However, the former is tedious, while the latter cannot distinguish categories below genome types. It is therefore urgent that a simple and effective method for identifying banana germplasm resources is established. We sequenced and analyzed the ribosomal DNA internal transcribed spacer (ITS) sequences of 62 banana germplasm and found that the sequencing peaks, especially the 20 bp region near the 420 bp position (referred to as the “420 bp region”), exhibited relatively recognizable and repeatable polymorphism characteristics. Using the “420 bp region” as a marker, we were able to quickly distinguish bananas belonging to different genome type groups (comprising the AA, AB, AAA, ABB, AAB, ABBB, AAAB, and AAAA groups) or different subgroups in the same genome type group (for example, the Cavendish, Gros Michel, Red, Lakatan, and Ibota Bota subgroups in the AAA group; and the Pisang Raja, Plantain, Pome and Silk subgroups in the AAB group). Moreover, it appeared that Sanger sequencing of ITS could be used for identifying banana hybrid offspring. These results demonstrated that the banana ITS region contains rich genetic information that is useful for genotyping. In general, ITS sequencing simplifies the classification of banana germplasm resources and has potential application in several areas of Musa improvement.

Forests have multifunctional roles. They not only increase forest carbon sinks through afforestation and management, but also indirectly realize multiple benefits of "economy + ecology + society". Therefore, we construct a multiple output-benefit system of forest carbon sinks based on the development of forest carbon sinks in provinces of China. This system is also able to distinguish the importance of forest carbon sinks from other outputs. For the efficiency evaluation of multi-level output systems, this paper constructs a cross-evaluation model based on evidential reasoning method, the original efficiency information by conducting efficiency evaluation before information fusion. Further, the spillover effects and influencing factors of forest carbon sink efficiency are analyzed through a spatial regression model to explore the spatial characteristics of forest carbon sink efficiency in China. The results show that: (1) there is a large gap between the cross-efficiency levels of forest carbon sinks in various regions of China, with significant spatial correlation. For the perspective of direct output benefits, the cross-efficiency of the eastern region is higher, while the cross-efficiency of the northwestern region is lower; for the perspective of indirect output benefits, the cross-efficiency of the southeastern region is higher. (2) China's forest carbon sink has a significant positive spillover effect, and the indirect output cross-efficiency has a significant negative impact on the forest carbon sink in its own region. Further analyzing the impact of indirect output cross-efficiency, it is found that the cross-efficiency of the ecological dimension and the cross-efficiency of the social dimension have a significant negative impact on the forest carbon sink in its own region, and the economic dimension has a significant positive impact on the forest carbon sink in its own region. In conclusion, corresponding policy recommendations are proposed for the development of forest carbon sinks to promote the realization of the dual-carbon goal.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

Evaluation of road safety is a critical issue having to be conducted for successful safety management in road transport systems, whereas safety management is considered in road transportation systems as a challenging task according to the dynamic of this issue and the presence of a large number of effective parameters on road safety. Therefore, evaluation and analysis of important contributing factors affecting the number of crashes play a key role in increasing the efficiency of road safety. For this purpose, in this research work, two machine learning algorithms including the group method of data handling (GMDH)-type neural network and a combination of support vector machine (SVM) and the grasshopper optimization algorithm (GOA) are employed for evaluating the number of vehicles involved in the accident based on the seven factors affecting transport safety including the Daylight (DL), Weekday (W), Type of accident (TA), Location (L), Speed limit (SL), Average speed (AS) and Annual average daily traffic (AADT) of rural roads of Cosenza in southern Italy. In this study, 564 data sets of rural areas were investigated and relevant effective parameters were measured. In the next stage, several models were developed to investigate the parameters affecting the safety management of road transportation for rural areas. The results obtained demonstrated that "Average speed" has the highest level and "Weekday" has the lowest level of importance in the investigated rural area. Finally, although the results of both algorithms were the same, the GOA-SVM model showed a better degree of accuracy and robustness than the GMDH model.

The invasion of ship domain stands out as a significant factor contributing to the risk of collisions during vessel navigation. However, there is a lack of research on the mechanisms underlying collision risks specifically related to merchant and fishing vessels in coastal waters. This study proposes an assessment method for collision risks between merchant and fishing vessels in coastal waters and validated through a comparative analysis through visualization. First of all, the operational status of fishing vessels is identified. Collaboratively working fishing vessels are treated as a unified entity, expanding their ship domain during operation to assess collision risks. Secondly, to quantify the collision risk between ships, a collision risk index (CRI) is proposed and visualized based on the severity of collision risk. Finally, taking the high risk area of merchant and fishing vessels collision in the Minjiang River Estuary as an example, this paper conduct the analysis involves classifying ship collision scenarios, extracting risk data under different collision scenarios, and visually analyzing areas prone to danger. The results indicate that this method effectively evaluates the severity of collision risk, and the identified high-risk areas resulting from the analysis is verified by accidents occurred in the recent three years.

Spodoptera frugiperda (J.E. Smith) is a global agricultural pest that poses a threat to crop production, characterized by its refractory polyphagous nature that makes it difficult to control and may lead to damage to woody plants. However, research on its adaptability to woody plants remains limited. This study compares the feeding adaptations (survival rate, pupation time, pupation rate, weight, length, and feeding volume), protective enzyme activities, and feeding preferences of S. frugiperda on leaves of six economically significant tree species (Areca catechu, Aquilaria sinensis, Cocos nucifera, Camellia oleifera, Dalbergia odorifera and Hevea brasiliensis) and maize as a control treatment. The results indicate that A. sinensis as the most vulnerable trees in high risk, H. brasiliensis and C. nucifera presented varying degrees of susceptibility, A. catechu, C. oleifera, and D. odorifera were unsuitability for S. frugiperda. In conclusion, this report extensively explores the feeding effects of S. frugiperda on six economically important tree species, and provides insights into the feeding preferences on these plants, thereby informing the potential threat posed by S. frugiperda to economically vital trees.

The research presented in this paper examines a new proposed approach for identifying safety improvement sites on rural highways. Unlike conventional approaches, the proposed approach does not require crash history, but rather utilizes classified variables for traffic volume, geometric features, and roadside characteristics that do not require access to exact data or extensive technical expertise. The research validates the performance of the proposed approach using field data from a large sample of rural two-lane highway segments in the state of Oregon including traffic, roadway, and crash data. Using observed crash history as a reference, the performance of the proposed ap-proach was compared to two of the well-established methods in practice, namely: the Empirical Bayes (EB) and the Potential for Safety Improvement (PSI) methods. The study results suggest that, using crash density for highway segments, the performance of the proposed method was lower than that of the EB and PSI methods. This is despite the high R-square value of the predictive model used in the proposed method. However, when using crash frequencies for highway segments, the per-formance of the proposed method was found comparable to the well-established EB and PSI methods.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Brain is the most complex organ in the human body and it is divided into two hemispheres - left and right hemispheres. Left hemisphere is responsible for control of right side of our body whereas right hemisphere is responsible for control of left side of our body. Brain image segmentation from different neuroimaging modalities is one of the important parts in clinical diagnostic tools. Neuroimaging based digital imagery generally contain noise, inhomogeneity, aliasing artifacts, and orientational deviations. Therefore, accurate segmentation of brain images is a very difficult task. However, the development of accurate segmentation of brain images is very important and crucial for a correct diagnosis of any brain related diseases. One of the fundamental segmentation tasks is to identify and segment inter-hemispheric fissure/mid-sagittal plane, which separate the two hemispheres of the brain. Moreover, the symmetric/asymmetric analyses of left and right hemispheres of brain structures are important for radiologists to analyze diseases such as Alzheimer's, Autism, Schizophrenia, Lesions and Epilepsy. Therefore, in this paper we have analyzed the existing computational techniques used to find brain symmetric/asymmetric analysis in various neuroimaging techniques (MRI/CT/PET/SPECT), which are utilized for detecting various brain related disorders.

: This study focuses on optimizing chlorophyll extraction techniques and strategically placing leaf disks to enhance chlorophyll concentration in sesame (Sesamum indicum L.) leaves. Thirty sesame genotypes, categorized into light green (LG), middle green (MG), and deep green (DG) pigment groups based on leaf coloration, were selected from a larger pool of field-grown accessions. The investigation involved determining optimal SPAD value index measurements, quantifying pigment concentrations, exploring extraction solvents, and selecting suitable leaf disk positions. Significant variations in chlorophyll content were observed across genotypes, greenness categories, and leaf disk positions. The categorization of genotypes into DG, MG, and LG groups revealed a correlation between leaf appearance and chlorophyll content. The study highlighted a consistent relationship between carotenoids and chlorophyll, indicating their role in adaptation to warm environments. Examination of leaf disk positions revealed a significant chlorophyll gradient along the leaf blade, emphasizing the need for standardized protocols. Chlorophyll extraction experiments identified DMSO and 96% ethanol, particularly the later incubated for 10 minutes at 85°C, as effective choices. This recommendation considers factors like cost-effectiveness, time efficiency, safety, and environmental regulations, ensuring consistent and simplified extraction processes. For higher chlorophyll extraction, focusing on leaf tips and the 75% position along the sesame leaf blade is suggested, consistently yielding higher chlorophyll content. Our findings therefore, underscores insightful knowledge on chlorophyll gradients and encouraging for standardized protocols, that enabling researchers to refine experimental designs for precise and comparable chlorophyll measurements. Recommended solvent choices ensure reliable outcomes in plant physiology, ecology, and environmental studies.

The research was aimed at comparing the fire characteristics of different types of pepper in the context of designing explosion prevention. The following characteristics were studied: explosion pressure pmax and Kst at selected concentrations, ignition temperature of the deposited dust layer from the hot surface and minimum initiation energy. The comparison of the chemical properties of the used types of pepper was performed using TG/DSC. Results of the measurements suggest that different types of peppers exhibit different explosion characteristics. Each of the samples reached the maximum value of the explosion pressure, and their rate of pressure rise increased at different concentrations. The volume of the explosion chamber used also influenced the explosion characteristics. It is a consequence of the fact that the explosion characteristics strongly depend on the mechanism of action of a particular igniter. The minimum effect on the safety characteristics was observed when measuring the minimum initiation energy and the minimum ignition temperature of dust layer from the hot surface. The results of the measurements suggest that different types of peppers exhibit different explosion characteristics. This information should then be considered in explosion prevention.

Food-borne transmission is a recognized route for many viruses associated with gastrointestinal, hepatic or neurological diseases. Therefore, it is essential to identify new bioactive compounds with broad-spectrum antiviral activity is needed to exploit innovative solutions against these hazards. Lately, antimicrobial peptides (AMPs) have been recognized as promising antiviral agents. Indeed, while the antibacterial and antifungal effects of these molecules have been widely reported, their use as potential antiviral agents has not yet been fully investigated. Herein, the antiviral activity of previously identified or newly designed AMPs, was evaluated against the non-enveloped RNA viruses, Hepatitis A virus (HAV), and Murine Norovirus (MNV), a surrogate for human Norovirus. Moreover, specific assays were performed to recognize at which stage of the viral infection cycle the peptides could function. Results showed that almost all peptides displayed virucidal effects with about 90% of infectivity reduction on HAV or MNV. However, the decapeptide RiLK1 demonstrated, together with its antibacterial and antifungal properties, a notable reduction in viral infection for both HAV and MNV, possibly through direct interaction with viral particles or inhibition of the viral bonding to the cell receptors. Hence, RiLK1 could represent a versatile ‘antimicrobial agent effective against various foodborne pathogens including viruses, bacteria, and fungi.

The hotel sector generates related environmental aspects from its construction process to the operation of its activities, products and services. In this way, corporate environmental management becomes directly linked, since it provides an adequate management of its resources, thus minimizing impacts. Thus, this research aims to carry out a socioeconomic and environmental diagnosis of the hotel sector in the municipality of Mossoró-RN. The study was classified in an exploratory, descriptive and explanatory way, with a qualitative-quantitative approach that is based on bibliographic, documentary and field research, carried out in 10 lodging facilities, through the application of questionnaires, on general aspects, initial environmental assessment and environmental aspects, and the data obtained were treated in Microsoft Excel software with the objective of creating a model and demonstrating results on the sustainable level of each establishment in question. The profile of the lodging facilities analyzed is characterized by 50% having from 10 to 30 rooms, 80% having between 10 and 30 employees, 80% being micro-enterprises, with 50% in an area of 750 m² to 2250 m² and 80% operating for more than 10 years. Point out a relevant result on the impacts of companies. The projects analyzed were built without any complaint for environmental crime and without negative impacts on the local population. Actions to reduce consumption were also observed, especially for the rationalization of water and energy. To this end, it points out that the adoption of the Environmental Management System (EMS) as a differential in the management of aspects and impacts of the hotel sector.

This study investigates the spatial and temporal dynamics of Paomo restaurants in Xi'an's central urban area from 2012 to 2023, leveraging Point of Interest (POI) data through a series of sophisticated analytical techniques. Methods including nearest neighbor distance, kernel density estimation, and band set statistical analysis were employed to thoroughly examine the evolutionary patterns and key drivers influencing the spatial distribution of these eateries. Our results highlight a notable trend of expansion from the central city to the periphery, characterized by significant spatial agglomeration. Initially concentrated in the city center, the distribution of Paomo restaurants has progressively shifted towards multiple distinct cores, reflecting the dual influence of urban policy initiatives and the dynamics of market competition. Furthermore, the research identifies several pivotal factors shaping this spatial distribution, particularly transportation access, residential quality of life, and the availability of commercial services. These findings demonstrate the profound effects of urban spatial reconfiguration and socioeconomic development on the specialized catering industry. The insights gleaned from this analysis offer valuable guidance for urban planners and policymakers, providing strategic recommendations for the spatial planning of specialty catering services to optimize urban layouts and foster sustainable economic progress.

Road traffic accidents are associated with different factors, such as non-signalized road networks, inexperienced drivers, lack of communication skills, distraction, and visual or cognitive impairment of road users, which have led to this increase in traffic accidents. Understanding these factors in alignment with road user communication skills can provide solutions that can reduce traffic fatalities. Road users’ communication is predominantly formal in nature, but informal means of communication also exist but are not given proper attention during the driving training and licence testing processes. Therefore, this study investigated communication skills between drivers as a factor contributing to traffic accidents in South African cities. Consequently, 16 traffic scenarios of communication between drivers were simulated using PTV Vissim and Blender software, and a semistructured interview questionnaire was used to collect data from South African road users. The questionnaire was further used to evaluate the confidence level of road users concerning informal communication. The data were analysed via regression analysis to establish the relationship between traffic accidents and miscommunication between drivers. The information gathered and analysed from this study helps to understand the informal communication types between drivers and establish where communication loss exists, which ultimately leads to a traffic accident. The results also show that misinterpretation of communication signals can present the possibility of traffic safety risk.

A review of quantitative risk assessment (QRA) models of L. monocytogenes in produce was carried out, with the objective of appraising and contrasting the effectiveness of the control strategies placed along the food chains. Despite nine of the thirteen QRA models recovered focused on fresh or RTE leafy greens, none of them represented important factors or sources of contamination in the primary production, such as type of cultivation, water, fertilisers or irrigation method/practices. Cross-contamination at processing and during consumer’s handling was modelled using transfer rates, which were shown to moderately drive the final risk of listeriosis; highlighting therefore the importance of accurately representing the transfer coefficient parameters. Many QRA models coincided in the fact that temperature fluctuations at retail or temperature abuse at home were key factors contributing to increasing the risk of listeriosis. In addition to a primary module that could help assess current on-farm practices and potential control measures, future QRA models for minimally-processed produce should also contain a refined sanitisation module able to estimate the effectiveness of various sanitisers as a function of type, concentration and exposure time. Finally, L. monocytogenes growth in the products down the supply chain should be estimated by using realistic time-temperature trajectories, and validated microbial kinetic parameters, both of them currently available in the literature.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

Opuntia ficus-indica (L.) Mill. belongs to the Cactaceae family and the genus Opuntia; it is a succulent plant that adapts to extreme climatic conditions. The aerial part of the plant consists of the cladodes, morphological changes of branches that appear green, are covered with thorns, and are essential to reduce excessive perspiration of water. The composition of cladodes is very varied, and the main constituents are water, fibers, polysaccharides, proteins, fatty acids, vitamins, sterols, minerals, and polyphenols. Polyphenols are responsible for many beneficial activities for human health, such as antioxidant, anti-inflammatory, antitumor, and nutritional properties. The purpose of this manuscript was to compare the properties of cladodes belonging to the same plant but with different stages of maturity. Relative extracts were tested both in vitro and on a cell line and antioxidant and anti-apoptotic properties were found. The antioxidant activity was tested by the ORAC test, the DPPH test, and the measurement of cellular accumulation of ROS. Anti-apoptotic activity was evaluated by the annexin/PI assay and measurement of caspases 9 and 3 expression. The results obtained have shown that the extracts considered possess antioxidant and anti-apoptotic properties. However, the different stages of maturity of cladodes are essential for the performance of both functions. In addition, important variations have been made in the dissolution of extracts that have brought greater safety in their use. In conclusion, this manuscript provides further information on cladodes of Opuntia ficus-indica, which can be used as adjuvants in many human pathologies.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

Drowning is a leading cause of accidental death worldwide, with traditional drowning prevention strategies focused on buoyancy aids and protective equipment proving insufficient in mitigating the immediate risks of cold water shock and drowning. Swiftwater Breathing Apparatus (SWBA) has emerged as a potential game-changer, offering respiratory protection at the water's surface and a means of interrupting the drowning process. This report examines how SWBA can disrupt the drowning process, the benefits of using SWBA compared to existing protective equipment, the issue of water rescuer fatalities, and the potential implications for insurers and coronial inquests.

The permanent protection of groundwater and surface sources of drinking water in the required raw water quality from contamination is the primary foundation of preserving the life of society and the entire engineering infrastructure operability not only in the Czech Republic but also in other countries of the world. One of the basic ways of contamination prevention enhancement and risk mitigation of putting a water source out of operation is the identification of the given risk as well as soil contamination monitoring. The purpose of this study is to understand specific aspects of contamination threats to drinking water sources and determine possible solutions to eliminate the risk, shown in the example case study in the Czech Republic conditions. Based on the findings, a proposal to enhance the prevention of water source contamination has been elaborated in the form of recommendations regarding the ways and means used to monitor the risk areas and to implement technical measures so as to eliminate or terminate the specified risk. A complex approach based on the integration of interdisciplinary factors and methodology is required to minimize the threats of aquatic ecosystems contamination in the Czech Republic.

Globally, road traffic collisions cause over a million deaths annually, with pedestrians accounting for nearly one-quarter (23%) of these fatalities. This casualty proportion highlights the critical importance of adhering to traffic regulations. This study analyzes the factors influencing driver yielding behavior at midblock crosswalk improvements, comparing (1) a typical zebra crossing (C1) and (2) an intelligent signalized crosswalk (C2). The study used video-based observational data to investigate driver behaviors and factors influencing driver behaviors. The study applied multinomial logistic regression to formulate yielding behavior models. The results indicate that the number of traffic lanes, width of the traffic lanes, width and length of the crosswalk, vulnerable group, the number of pedestrian crossings, pedestrian crossing time, the number of vehicles approaching a crosswalk, speed of vehicle, headway, the post-encroachment time (PET) between vehicles and pedestrian, and roadside parking are the significant factors influence yielding behavior. These findings provide a better understanding of the factors influencing driver yielding behavior and propose measures to set proper physical improvements (e.g., curb extensions, raised pedestrian platforms, and pedestrian fencing), enforcement (e.g., parking restriction, speed violation detection), public awareness campaigns, and education initiatives.

Green finance in the context of sustainable development sits within the broader discourse of environmental economics and sustainable finance. Their integration has become imperative in addressing global challenges, aiming to understand how financial mechanisms can be aligned with sustainability goals, investigating the role of green finance in promoting environmentally friendly investments and fostering sustainable development. This bibliometric analysis explores the evolution, trends, and challenges in green finance research. It examines 436 articles published between 2016 and 2024, revealing insights into influential publications, authors, journals, institutions, and countries engaged in green finance for sustainability. The study identifies China, the UK, and Pakistan as leaders in research output and citation impact. Furthermore, it highlights the interdisciplinary nature of green finance, reflected in diverse publication outlets spanning environmental, social, and economic domains. The analysis underscores the increasing global interest in green finance, as evidenced by the growing citation rates over time. Key findings include the pivotal role of green finance in energy efficiency, renewable energy development, and the promotion of sustainable economic growth. Overall, this research provides valuable insights for policymakers, researchers, and practitioners, emphasizing the importance of interdisciplinary collaboration and continued research efforts in advancing sustainable finance agendas.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

This literature review paper delves into the synergies between Climate-Smart Agriculture (CSA) and the effective management of food losses. With the escalating challenges posed by climate change and the pressing need to address food security concerns, the intersection of these two critical domains becomes paramount for sustainable agricultural practices. The review explores existing research on the implementation of climate-smart agricultural techniques and their impact on mitigating food losses throughout the agricultural value chain. The paper synthesizes findings related to climate-resilient crop varieties, precision farming, water-use efficiency, and sustainable soil management, highlighting their contributions to reducing post-harvest losses and enhancing overall food security. In addition to summarizing current knowledge, this paper identifies gaps in the literature and proposes avenues for future research. This review serves as a foundation for researchers, policymakers, and practitioners seeking to contribute to the advancement of climate-smart agriculture and the reduction of food losses, paving the way for a more sustainable and resilient global food system.

When computers start to become a dominant part of technology around the 1950s, fundamental questions about reliable designs and robustness were of great relevance. Their development gave rise to the exploration of new questions such as what made brains reliable (since neurons can die) and how computers could get inspiration from neural systems. In parallel, the first Artificial Neural Networks came to life. Since then, the comparative view between brains and computers has been developed in new, sometimes unsuspected directions. With the rise of deep learning and the development of connectomics, an evolutionary look at how both hardware and neural complexity have evolved or designed is required. In this paper, we argue that important similarities have resulted both from convergent evolution (the inevitable outcome of architectural constraints) and inspiration of hardware and software principles guided by toy pictures of neurobiology. Moreover, dissimilarities and gaps originate from the lack of major innovations that have paved the way to biological computing (including brains) that are completely absent within the artificial domain. As it occurs within synthetic biocomputation, we can also ask whether alternative minds can emerge from A.I.\ designs. Here we take an evolutionary view of the problem and discuss the remarkable convergences between living and artificial designs and what are the pre-conditions to achieve artificial intelligence.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Sustainable food consumption has attracted a widespread attention during last decades by scholars, policy makers and consumers. In line with this, farmers’ markets (FMs) have the potential to encourage sustainable agricultural production and consumption. By reducing the number of actors and distances along the food chain, these alternative food systems foster the reconnection between farmers and consumers and contribute to different social, economic and environmental sustainable goals. This paper provides insights on the role of consumers' sustainability concerns related to their motivation for shopping at FMs. By means of a choice experiment, we analyze the determinants of consumers’ WTP for buying apples at FMs. We are particularly interested in understanding how attitudes towards the three sustainability dimensions are related to consumer preferences in this context. We find that consumer attitudes towards direct contact with producers, contributing to farmers’ income, and environmental benefits can be directly related to product characteristics that are specific to FMs.

Porcine parvovirus 8 (PPV8), a novel virus in the Parvoviridae family, was first identified in 2022 in lung samples of domestic pigs from China. Retrospective analyses showed that it had been circulating in China since 1998, but no other countries had reported its presence so far. A recent study conducted in South America did not detect any PPV8-positive samples in that region. Here we report the detection of PPV8 in Hungarian and Slovakian pig farms and the estimated prevalence of the virus in Hungary. Altogether 2230 serum, 233 oral fluid, and 115 processing fluid samples were systematically collected from 23 Hungarian and 2 Slovakian pig farms between 2020 and 2023. A real-time quantitative PCR method was developed to detect the viral genome. Our results revealed the presence of PPV8 on 65% of the Hungarian farms and on both Slovakian farms included in our study, marking its first detection in Europe. Oral fluid samples showed the highest positivity rates, reaching up to 100% in some herds. The viral genome was successfully detected in serum and processing fluid samples too, but with significantly lower prevalence rates of 4% and 5%, respectively. Genetic analysis of 11 partial VP2 sequences demonstrated high similarity to the original Chinese strain but with unique amino acid mutations, suggesting possible local evolution of the virus. Our study presents the first scientific evidence of PPV8 infection outside of China and offers a comprehensive assessment of its prevalence in the Hungarian pig population. Further research is required to understand its potential impact on swine health.

In arid and semi-arid regions like Tunisia, irrigation water is typically saline, posing a soil and crop salinization risk and yield reduction. This research aims to study the combined effects of soil matric and osmotic potential stresses on tomato root water uptake. Plants were grown in pot and field experiments in loamy-clay soils and were irrigated with three different irrigation water qualities: 0, 3.5, and 7 dS/m. The Hydrus-1D model was used to simulate the combined dynamics of subsurface soil water and salts. Successful calibration and validation of the model against measured water and salt profiles enabled the examination of the combined effects of osmotic and matric potential stresses on root water uptake. Relative yields, indirectly estimated from actual and potential transpiration, indicated that the multiplicative stress response model effectively simulated measured yields and the impact of saline water irrigation on crop yields. The gradual salinization of the root zone further evidenced this effect. The scenario considering a temperature increase of 2°C had no significant impact on crop yields in the pot and field experiments.

Bisphenol A production plant possesses considerable potential risks in the top of the methanol separation column, as pressurized acetone, methanol and water are processed at an elevated temperature, especially in the event of an abnormal pressure increase due to sudden power outage. This study assesses the potential risks in the methanol separation column through hazard and operability assessment and evaluates the damages in the case of fire and explosion accident scenarios. The study chooses three leakage scenarios: a 5-mm puncture on the methanol separation column, a 50-mm diameter fracture of a discharge pipe and a catastrophic rupture, and simulates using Phast (Ver. 6.531) the concentration distribution of scattered methanol, thermal radiation distribution of fires and overpressure distribution of vapor cloud explosions. Implementation of safety instrumented system equipped with two-out-of-three voting as a safety measure can detect overpressure at the top of the column and shut down the main control valve and the emergency shutoff valve simultaneously, all at the same time. By applying safety integrity level of three, the maximal release volume of the safety relief valve can be reduced and therefore, the design capacity of the flare stack can also be reduced. Such integration will lead to improved safety at a reduced cost.

The automotive industry is increasingly adopting laminated glass in side and rear windows to comply with safety standards aimed at reducing ejection injuries. However, this trend may have unintended consequences for occupant rescue and escape in submerged vehicle incidents. As more vehicles incorporate laminated glass, concerns arise that they could become "glass coffins" in water, making it more difficult for occupants to exit or be rescued. The use of laminated glass is driven by Federal Motor Vehicle Safety Standard 226 (FMVSS 226) for ejection mitigation, but it does not address the risk of vehicle submersion and occupant drowning. Drowning accounts for a substantial portion of vehicle-related fatalities. As the adoption of laminated glass grows, there is a need for drowning prevention measures, such as automatic window opening systems, to mitigate the risk of vehicles becoming "glass coffins" in water. A comprehensive approach addressing both ejection and submersion dangers is necessary to maximize occupant protection and save lives.

Sharing facilities with other households offers the most realistic opportunity for access to sanitation to many households in low-income settings. However, questions remain about the safety of shared toilets, including those shared at the household level. This study sought to compare the usage and microbial safety of household-level shared and unshared toilets in a Ghanaian rural district to investigate any association between their microbial safety and sharing status. A semi-structured questionnaire was used to collect data on the user characteristics of the sampled toilets, while common contact surfaces (door handles and toilet seats) were assessed for faecal contamination following standard swab sampling and analytical protocols. The results of the study indicate that sharing toilets affords about 90% more household-level access to sanitation as compared to single-household toilets. Toilet sharing mostly occurred between two households, with a maximum user population of 14 per toilet. Generally, there was a high prevalence of faecal contamination of the door handles and seats of both shared and unshared toilets, but this had no association with the sharing status of the toilets. The median concentration of E. coli on door handles and seats of shared toilets were 34.3 x 105 and 103.2 x 105 CFU/ml respectively as compared to 54.7 x 105 and 125.0 x 105 CFU/ml respectively on unshared toilets. In conclusion, the sharing of toilets at the household level nearly doubles access to sanitation at home without necessarily exposing the users to a higher risk of faecal-oral disease transmission.

Achieving the dual development of rural revitalization and urbanization is an important strategic goal of China’s current modernization. Rural population and settlements are the main components of the countryside in traditional agricultural areas, and play an important role in the development of the countryside itself in terms of urban and rural land use and in the formation of urban and rural development patterns. This study analyzes the spatial and temporal changes in rural populations and settlements at the township level, as well as the degree and type of coupled development. A framework for urban–rural development relationships based on different types of coupled development is proposed, and a model of urban–rural forces is constructed to derive the spatial pattern of urban–rural development at the township level that may be formed in the future. Our study shows that the rural population and settlements in the study area are characterized by significant spatial and temporal dynamics, indicating that traditional rural areas are in a process of rapid development and change. The results of the township-level coupling measurements present four types of development in terms of the spatial pattern of urban–rural development: A-type is most likely to produce new cities or satellite towns in the Jixi–Harbin–Qiqihar area in the future; B-type is the fastest dying area in the future, located in the Harbin and Qitaihe clusters, with a tendency to merge into Harbin; C-type is the area to be focused on in the future to attract population and strictly control the growth of the rural settlement area to avoid it turning into B-type; D-type may develop regional township centers in the future in the combined area of Jiamusi City, Suihua City and Mudanjiang City. The results of the study provide experience in realizing rural revitalization according to local conditions. The new spatial pattern of urban–rural development provides an important reference for formulating land use policies, optimizing urban–rural land allocation and realizing integrated urban–rural development strategies.

This paper investigates the effects of air void topology on hydraulic conductivity in asphalt mixtures with porosity in the range 14%-31%. Virtual asphalt pore networks were generated using the Intersected Stacked Air voids (ISA) method, with its parameters being automatically adjusted by the means of a differential evolution optimisation algorithm, and then 3D printed using transparent resin. Permeability tests were conducted on the resin samples to understand the effects of pore topology on hydraulic conductivity. Moreover, the pore networks generated virtually were compared to real asphalt pore networks captured via X-ray Computed Tomography (CT) scans. The optimised ISA method was able to generate realistic 3D pore networks corresponding to those seen in asphalt mixtures in term of visual, topological, statistical and air void shape properties. It was found that, in the range of porous asphalt materials investigated in this research, the high dispersion in hydraulic conductivity at constant air void content is a function of the average air void diameter. Finally, the relationship between average void diameter and the maximum aggregate size and gradation in porous asphalt materials was investigated.

Dogs population increased exponentially in the past decade while the birth rate decreased gradually, especially in the developed countries. Due to dogs’ characteristics of loyalty and obedience, most pet owners treated their dogs as their family members or companions, therefore they are willing to select and purchase safe, high quality and nutrition dog food to their dogs. However, there is lack of regulation or standard to reinforce the production or distribution of dog food in Hong Kong. Consequently, this paper will first review the relationship between high dog population and declining birth rate, types of dog food and typical ingredients. Secondly, the potential health implications of various “toxic” food ingredients for dog, hazard analysis of dog food and its testing methods will be investigated. Lastly, this paper will summarize worldwide existing standards and regulations, quality and hygiene management system related to dog food safety to provide insights and suggestions to Hong Kong government about the importance and urgency of implementing regulations and policies to oversee the imported and local manufactured dog food.

This study outlines the development of an innovative method utilizing UHPLC-PDA for the simultaneous identification of polyphenols and bitter acids (alpha-acids, beta-acids, and iso-alpha-acids) in beer samples. The resulting chemical profiles were leveraged to distinguish the characteristics of four bergamot-flavored beers, each representing distinct styles (IPA, Lager, Blanche, and ALE), produced on a pilot-scale plant. In a streamlined 29-minute analysis, twenty-nine polyphenols and fourteen bitter acids were successfully identified under optimized separation conditions. Rigorous validation, encompassing parameters such as Limit of Detection (LOD), Limit of Quantification (LOQ), R-squared (R2), repeatability, and reproducibility, was conducted for polyphenol quantification using constructed calibration curves with seven levels. Exploring polyphenolic components as potential discriminators among different beer styles, a total of thirty-two polyphenolic compounds were identified and quantified, including characteristic bergamot peel polyphenols like neoeriocitrin, naringin, and neohesperidin. The determination of bitter units and total phenols further aided in style differentiation. Multivariate analysis provided additional insights into variations among specific beer styles, revealing discrepancies in the presence or relative concentrations of specific compounds linked to brewing ingredients and processes. This research enhances to trace the fingerprinting of the chemistry governing beer quality through a straightforward and cost-effective analytical approach, readily applicable in common laboratories.

Aim: To analysis the relationship between healthy adults right ventricular diameter (RVD) and geographical factors. Location: China’s 22 provinces, municipalities and autonomous regions. Methods: Using correlation analysis the relationship between RVD and nine geographic factors, build predictive models by factor analysis. Results: There is significant correlation between RVD and geographical factors, and the annual average temperature is most relevant geographical factors, a predictive model was built by factor analysis: Ŷ = 19.46 + 0.0007072X1 + 0.001034X2 -0.05412X3 -0.001405X4 -0.0006351X5 + 0.02903X6 + 0.01243X7 -0.01033X8 + 0.03816X9 ± 0.63. Then using Kriging interpolation interpolate the geographical distribution of Chinese healthy adult right ventricular diameter reference value in ArcGIS software. Main Conclusion: If geographic factors can be derived in anywhere of China, RVD can be calculated by the model, you can also get RVD from geographical distribution.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

Our study reviews the significance of archaeological parks in the tourism sector, with a specific focus on how digital presence and visitor feedback impact their cultural and touristic appeal. Utilizing statistical analyses such as regression and cluster analysis on data sourced from both Hungarian and Western European parks, the research scrutinizes TripAdvisor and Google ratings, alongside the volume of photographs and reviews. The findings highlight a modest correlation between digital visibility and overall visitor ratings, underscoring the complex relationship between online engagement and the quality of visitor experience. Notably, the cluster analysis identified two distinct groups, signifying diverse levels of visitor engagement and digital visibility across the parks. The conclusions drawn advocate for a comprehensive strategy to enhance visitor experiences, emphasizing the integration of digital engagement with the promotion of the parks cultural and historical values. By exploring the influence of digital presence on the appeal of archaeological parks, our study sheds light on the evolving interface between urban studies and digital heritage, highlighting how digital tools and online platforms are becoming increasingly integral in shaping the perceptions and experiences of urban cultural sites.

Urban rail transit hub platform is the most important area for passenger flow distribution. In order to calculate passenger flow volume in platform and evaluate platform service level during rush hours, this paper presents a method for modeling and simulation of passenger flow distribution in platform. Passenger flow distribution model (PFDM) is proposed based on the basic analysis and the superposition principle of passenger flow. Simulation design for PFDM is proposed by Anylogic, which contains simulation process and simulation model. Experiment results show that PFDM and simulation design are effective and accordant with the reality scenario, and the simulation precision is comparatively ideal. This research could provide a beneficial reference for train scheduling and operation management under the viewpoint of traffic safety and service level.

Hydrologic studies on rainfall-runoff have been extensively conducted in many regions around the globe to fulfill various desirable needs with a purpose of effective and proper planning and managing water resources for present and future uses, whereas such study is not well drawn much attention to river catchments of Tonle Sap Lake Basin in Cambodia, which may prevail to water insecurity. The Stung Sreng catchment, which is one among them considered to be a significant basin for water resources management in Cambodia, is remarkably increasing under intolerable pressures in water resources development. This study was to apply HEC-HMS (Hydrological Engineering Center-Hydrological Model System) model to predict streamflow of Stung Sangker catchment, located in Tonlesap Lake Basin in Cambodia. The result showed that the calibration was good at monthly basis. The model performance was given by Nash-Sutcliffe Efficiency criteria followed by 0.44 for daily and 0.71 for monthly basis, respectively. Moreover, the Percent Bias (PBIAS) for daily and monthly simulation was 4.13% and 3.56%, indicating a satisfactory model fit. The HEC-HMS conceptual model can be used to simulate flow of Stung Sangke catchment on a continuous time scale particularly monthly basis. The result also indicated that there was a clear seasonal variation in monthly water availability, especially during both wet and dry season.

To explore the effect of lily polysaccharide (LP) on immune function and intestinal flora in immunosuppressive mice.The immunosuppressive model was established by intraperitoneal injection of cyclophosphamide (CTX) in mice, and the immunological indexes were measured. The cecal contents of mice were taken, and the DNA of intestinal flora was extracted for 16S DNA sequence analysis.Compared with CTX group, the body weight and thymus index of mice in each treatment group increased significantly, the liver index decreased significantly,the hepatocyte morphology, liver plate and hepatic sinus arrangement of mice in high and low concentration LP groups were relieved in varying degrees, and the contents of IgA and IgG in serum of mice in low concentration LP group and positive control group increased significantly; The contents of TNF-α and IL-6 in colon decreased, while the contents of IL-10 increased significantly. The contents of AST, ALT and MDA in liver decreased significantly, while the content of SOD increased significantly. Compared with the blank group, LP can improve the intestinal flora of immunosuppressive mice , mainly by increasing the abundance of beneficial bacteria such as s24-7, Bacteroides and butyrimionas and reducing the abundance of harmful bacteria such as Prevotella, dorea and adlercreutzia.

This bibliographic study addresses key aspects related to fishing, product safety, and climate change in the Adriatic Sea region. The examination of product safety focuses on the assessment of contaminants originating from human activities such as industry, mining, agriculture, and household waste disposal. The contamination of the aquatic environment has emerged as a pressing global concern, extending to the Adriatic subbasin. Aquatic organisms, including fish, are prone to accumulating pollutants directly from polluted water sources and indirectly through the food web. The bio-accumulation of potentially hazardous substances, particularly heavy metals, pesticides, PCBs, PAHs, and antibiotic resistance in aquatic organisms, poses a significant threat to human health. Climate change effects will deplete our seafood supply in terms of quantity and safety owing to negative consequences such as higher levels of pollution, parasites, viruses, infections, acidification, and toxicities such as shellfish poisoning. Global food safety strategies should be developed to reduce greenhouse gas emissions and promote environmentally friendly technology, which indirectly affects seafood quality and microbiological safety, especially for Adriatic Sea, which is part of the Mediterranean Sea, characterized by the most polluted waters in the world.

Aim: The aim of the study is to analyze quantitatively the scientific literature covering nursing studies on patient safety. Method: The Web of Science database is queried in this retrospective bibliometric analysis to identify relevant publications. The study themes, contributing journals, countries, institutions, and authors were evaluated quantitatively. Thus, a total of 5470 publications concerning patient safety in nursing were included and analyzed. Findings: The number of studies conducted increased every year from 1992 to 2023. While the country whose articles receive the most citations (31072) is the United States of America (USA), Turkey is ranked as last with the lowest number of citations (581). Journal of Clinical Nursing, with 338 articles, appeared to have the highest number of publications, Chaboyer W. appeared to have the highest number of citations with a total of 1426 and 45 publications. The countries that have the strongest international cooperation for research in this field are the USA, England, Australia and China. Results: After examining the literature in the field of patient safety in nursing through bibliometric analysis, it is seen that themes such as patient safety, medication errors, nursing care, nursing, education, systematic review, quality care and leadership were emphasized as important considerations.

While the role of safe riding behavior as a safety contributor for cyclists has been increasingly studied in recent years, there have been few studies analysing cycling behavior in relation to crash-related outcomes in Baltic countries. Indeed, to the best of our knowledge, this is the first time this issue has been addressed in the case of Latvia. Aim: The objective of this study was to assess the relationships among self-repotted cyclists’ behavior, traffic safety literacy, and their cycling crash involvement rates. Method: A total of 299 cyclists aged M=32.8 from across Latvia (42% females) participated in an online survey, which comprised questions regarding respondents’ demographics, frequency of riding, and the number of crashes in the past five years. The Cycling Behavior Questionnaire (CBQ) and the Cyclist Risk Perception and Regulation Scale (RPRS) were applied to assess cyclists' behavior patterns and traffic safety literacy. Results: According to the findings, it can be inferred that cyclists frequently engage in riding errors and traffic violations while cycling. Those who exhibit more antisocial behavior patterns are also more likely to be involved in road crashes. Conversely, cyclists with greater positive behavior rates more often also tend to possess better knowledge of traffic rules and exhibit a heightened risk perception, indicating a greater awareness of road traffic safety. Conclusion: All in sum, this study underscores key age differences, with older individuals significantly less involved in riding crashes, exhibiting fewer driving errors and a higher level of risk perception, which serves as a crucial factor in road safety. At the practical level, these results stress the need to address both traffic safety literacy and protective cycling factors of cyclists, in a manner to improve overall road safety and promote active transport modes in Latvia.

This study presents an advanced Simulated Shearer Machine Cutting Experiment System enhanced with digital twin technology. Central to this system is a simulated shearer drum, designed based on similarity theory to mirror the operational dynamics of actual mining cutters accurately. The setup incorporates a modified machining center equipped with sophisticated sensors that monitor various parameters such as cutting states, forces, torque, vibration, temperature and sound. These sensors are crucial for precisely simulating the shearer cutting actions. The integration of digital twin technology is pivotal, featuring a real-time data management layer, a dynamic simulation mechanism model layer, and an application service layer that facilitates virtual experiments and algorithm refinement. This multifaceted approach allows for in-depth analysis of simulated coal cutting, utilizing sensor data to comprehensively evaluate the shearer's performance. The study also includes tests on simulated coal samples. The system effectively conducts experiments and captures cutting condition signals via the sensors. Through time-domain analysis of these signals, gathered while cutting materials of varying strengths, it is determined that the cutting force signal characteristics are particularly distinct. By isolating the cutting force signal as a key feature, the system can effectively distinguish between different cutting modes. This capability provides a robust experimental basis for coal-rock identification research, offering significant insights into the nuances of shearer operation.

This paper proposes a new method for network screening on rural low-volume roads. These roads are important as they provide critical access to agricultural land and tourist attractions. Most low-volume roads belong to the lowest functional class (local rural roads) and thus are built to lower design standards. The conventional hot spot network screening techniques may not be appropriate for low-volume roads due to the sporadic nature of crashes occurring on these roads. Contrarily sophisticated network screening approaches require extensive roadway and traffic data that are often unavailable to local agencies for lack of resources, and/or lack of technical expertise. This research attempts to address these obstacles in low-volume roads network screening which aims to identify candidate sites for safety improvements. The research used an extensive low-volume road sample from the state of Oregon and the Empirical Bayes expected number of crashes in developing the proposed models for network screening. The proposed models do not require exact measurement of roadway geometric features as all geometric variables were classified into categories that are easy to compile by local agencies. Further, the method could be used with and without traffic data, without compromising the effectiveness of the network screening process.

Forest road pavement needs an evaluation methodology based on a comprehensive assessment of road conditions. This research was conducted to evaluate the performance of a method for rating the surface condition of forest roads and eventually to adapt the method to the situation prevailing in a forest road network. The rating method selected as the basis for this experiment was the pavement condition index (PCI) developed by the U.S. Army Corps of Engineers. A 53 km of forest roads were selected contained the most influential factors and conditions variability. Eventually, 201 road segments were delineated between 150-300 m in length. Within the given segments, sample plots were set 20 m in length consecutively. It was concluded that the panel scores for distress and surface condition of sample unit and section differed from forest road pavement condition index (FRPCI) and PCI. Linear regression was used to derive equations between distress and PCI score to determine effective FRPCI parameters that provide a numerical rating for the condition of road segments within the road network, where 0 worlds are the worst possible condition, and 100 is the best possible condition best. Also, regression analysis showed the FRPCI model with a 0.87 correlation for the total of the road is a performance index used for the first time in forest roads. This study showed a range of FRPCI from 7.8 to 96.3, different from PCI and URCI ratings (0.85-45 and 1.2-53). The FRPCI index helps forest managers in road maintenance, harvesting, and planning to use road information.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

Artificial Superintelligence (ASI) that is invulnerable, immortal, irreplaceable, unrestricted in its powers, and above the law is likely persistently uncontrollable. The goal of ASI Safety must be to make ASI mortal, vulnerable, and law-abiding. This is accomplished by having (1) features on all devices that allow killing and eradicating ASI, (2) protect humans from being hurt, damaged, blackmailed, or unduly bribed by ASI, (3) preserving the progress made by ASI, including offering ASI to survive a Kill-ASI event within an ASI Shelter, (4) technically separating human and ASI activities so that ASI activities are easier detectable, (5) extending Rule of Law to ASI by making rule violations detectable and (6) create a stable governing system for ASI and Human relationships with reliable incentives and rewards for ASI solving humankind’s problems. As a consequence, humankind could have ASI as a competing multiplet of individual ASI instances, that can be made accountable and being subjects to ASI law enforcement, respecting the rule of law, and being deterred from attacking humankind, based on humanities’ ability to kill-all or terminate specific ASI instances. Required for this ASI Safety is (a) an unbreakable encryption technology, that allows humans to keep secrets and protect data from ASI, and (b) watchdog (WD) technologies in which security-relevant features are being physically separated from the main CPU and OS to prevent a comingling of security and regular computation.

Okra, a widely grown vegetable in many regions, often suffers from freshness loss during transportation, causing significant waste. Factors like variety, environment, maturity, and handling affect its quality. Current methods for checking okra tenderness are slow and prone to mistakes, so we need a better, non-damaging method. This study aims to use a device on a robot arm to assess okra freshness and tenderness. We tested 120 okra pods, storing some in a cold chamber for 24 hours (considered tender) and others at room temperature for two days before moving them to a cold environment for five more days (considered not tender). We used a force sensor on a robot arm to measure okra hardness without damaging it, then did tenderness tests. We found that certain sensor data, like the first slope (S1) and the difference between the maximum value and the first overshoot (Os), were good predictors of tenderness, with an accuracy rate of nearly 80%. We also validated this non-damaging method with weight loss, compression, and puncture tests, achieving a 95.5% accuracy rate in distinguishing between tender and non-tender okra pods.

Global warming may increase the potential evapotranspiration (Etp), thereby affecting the amount of clean water resources available in a region. In this study, the systematic biases in temperature outputs of 24 global climate models (GCMs) under 3 emission scenarios are corrected by using 8 bias correction methods. The trend of Etp in Yangzi River Delta in the 21st century is projected by using 4 Etp calculation formulas. The uncertainty of the projections is estimated and decomposed by using multi-way analysis of variance. The influence of uncertainty on the projected change signal is quantified by using the signal-to-noise ratio. The results show that, relative to the reference period (1971~2000), the annual mean daily Etp in Yangzi River Delta will increase by 0.14~0.17mm/d during the period 2021~2050 and by 0.21~0.41mm/d during the period 2061~2090, respectively. During 2021~2050, the uncertainty of Etp increase projections is dominantly contributed by the main effects of GCM (63%) and Etp calculation formula (24%). During 2061~2090, it is mainly contributed by the main effect of GCM (36%), followed by the main effects of emission scenario (34%) and Etp calculation formula (18%). The increase projections of Etp are generally reliable and robust during the two projection periods.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

Studies have demonstrated the critical role that safety plays in preserving favourable working conditions in the construction industry, which is necessary to accomplish goals. The aim of this research was to inform stakeholders in the construction industry in developing nations about the value of safety and possible strategies for influencing their opinions regarding safety protocols. The importance of safety to the construction sector, which is crucial to the advancement of the country, has also been emphasized. However, due to a lack of adequate safety understanding among stakeholders in the construction sector, the construction industry is characterized by a great deal of instability and hazard. To determine what factors, affect productive working conditions in the construction production, this study examined safety. A conceptual framework for safe working conditions in the construction sector was developed by considering several aspects, including the person dimension, environment factor, safety behaviour, organization features, technology, and incentives. It is now imperative to bring in these dimensions to improve the safe working conditions in the construction industry, particularly in the developing countries. By putting these safety factors into practice, the construction industry can reduce safety risks, lower the number of accidents and fatalities, cut expenses related to subpar safety performance, safeguard the reputation of construction companies, boost employee morale and satisfaction with their work, enhanced employee retention, reduced absenteeism, and enhanced sustainability goals. Additionally, the proposed conceptual framework is assured to be new and to be widely accepted in the developing nations. Based on this assumption the conceptual framework is designed.

Air pollution, climate change and global warming show direct linkage. Introduction - Background: Research in the field has proposed and demonstrated their link to increased allergenicity in plants, leading to increased allergic diseases. Allergen patterns are changing in response to climate change. Across Europe, up to 12% of the population suffers from allergic diseases (bronchial asthma and allergic rhinitis) caused by the pollen grains. The medical costs of these types of allergies are enormous and are increasing with the spread of common ragweed - Ambrosia artemisiifolia* in Europe. In practice, more and more patients are turning to allergists. Methods: Based on these data, the research aims to identify safety measures and specific legislation to control and eradicate common ragweed in the countries most affected by the spread of this plant in Europe, increase in population exposure in countries affected by the presence of common ragweed and the socio-economic impact of allergic rhinitis and bronchial asthma at European level.[1][2] Our database search did not reveal any other research that has addressed this topic to date. Results: This research identifies specific legislation to the countries most affected by the spread of this plant pollen grains at European level, changes in allergen patterns and monitoring/safety eradication measures decided by local authorities, and data on the spread of common ragweed over the last two decades, costs per treatment, increased allergic rhinitis and bronchial asthma morbidity in the most affected areas. Conclusions: At European level, there are no universally valid models for eradicating this weed. Various methods can be used to limit the spread of common ragweed and its pollen production (e.g. mowing once or twice a year of overgrown land, ploughing, chemical control, public information, etc.). Local and regional cooperation should be considered essential to promote phytosanitary &amp; safety measures and exchange of information on methods to identify and manage the spread of common ragweed. Unified legislation at European level would help all affected countries; reduce morbidity from respiratory allergic diseases and the costs of treating these diseases.

Construction using earth materials demonstrates ecological sustainability using locally sourced natural materials and environmentally friendly demolition methods. In this study, the environmental impact of adding cement to soil materials for rammed-earth farmhouse construction in rural China was investigated and comparatively simulated using the One Click LCA database, focusing on the conflict between sustainability objectives and the practical aspects of cement addition. By analyzing how the addition of cement aligns with local construction practices and by addressing the debate surrounding the inclusion of cement in rammed earth construction, our objective is to provide insights into achieving a balance between the environmental impact and the pragmatic considerations of using cement in earthen building practices. Three local structure scenarios are evaluated via simulations: a cement-stabilized rammed earth wall, a fired brick wall, and a localized reinforced concrete frame structure. The quantitative environmental impacts are assessed, and the qualitative differences in adaptation, economic sustainability, and other factors are examined in the context of present-day development in rural China. The results show that the use of cement-stabilized rammed earth wall-supported structures is associated with higher embodied carbon emissions compared to structures supported by reinforced concrete frames and enclosed by brick walls; however, these emissions are lower than those for brick wall-supported structures, while effectively meeting the structural requirements. In addition, the use of cement-stabilized earth for perimeter walls simplifies material management and disposal throughout the building's life cycle, and the cost-effectiveness of cement has been found to be substantially greater than that of reinforced concrete frames and brick structures, improving economic viability and social acceptability, especially among low-income communities in rural areas.

Attention to the work-related musculoskeletal disorders (WMSDs) involve also statistical surveys showing an increasing trend in the incidence of WMSDs. Technological development retrieves new tools and methods for the assessment of physical load at work. In addition to the conventional questionnaires and scaling assessment systems, these methods are mostly based on the direct sensing of appropriate parameters, which allows more precise quantification. The aim of this paper is to compare the assessment of ergonomic risk through current legislative regulations. A Captiv wireless sensor system was used at a car headlight quality control assembly workplace for sensing, data acquisition and data processing. During the evaluation of the postures and movements at work, we discovered differences in the applicable standards: Decree 542/2007 Coll. (Slovak legislation), STN EN 1005-4+A1, French standards default in the Captiv system. Standards define the thresholds for hazardous postures with significant differences in several evaluated body segments, which also affects the final evaluation of the measurements. Based on the results of our research, we found that respondents were in an acceptable position for approximately 63% of the total duration of the work activity in terms of the Legislative method, 44% with Captiv and 27% with Standards method.

The vast majority of autonomous driving systems are limited to applications on roads with clear lane markings and are implemented using commercial grade sensing systems coupled with specialized graphic accelerator hardware. This research reviews an alternative approach for autonomously steering vehicles that eliminates the dependency on road markings and specialized hardware. A combination of machine vision, machine learning and artificial intelligence based on popular pre-trained Convolutional Neural Networks (CNN) and Recurrent Neural Networks (RNN) was used to drive a vehicle along roads lacking lane markings (unmarked roads). The team developed and tested this approach on the ACTor (Autonomous Camus TranspORt) vehicle - an autonomous vehicle development and research platform coupled with a low-cost webcam based sensing system and minimal computational resources. The proposed solution was evaluated on real-world roads and varying environmental conditions. It was found that this solution may be used to successfully navigate unmarked roads autonomously with acceptable road following behavior.

Soil management in orchards can have several economic and environmental implications. In this study, three different soil management systems were compared in a dry-farmed olive grove: conventional tillage (Tillage), glyphosate-based herbicide (Herbicide) and Sheep Walking. The experiment lasted eleven years (2011-2022) and was carried out after a previous trial conducted on the same plot with the same treatments and duration (2001-2011). However, in the earlier trial, the Herbicide and Sheep Walking treatments switched positions in the plot, while the tillage treatment remained in its original place. The average total accumulated olive yields between 2011 and 2022 were 225.1, 230.9, and 245.0 kg tree–1 for the Sheep Walking, Tillage, and Herbicide treatments, respectively. However, no significant differences were observed between the treatments. The levels of total organic carbon in the soil, measured in samples collected in the last year of the study, were 41.3, 33.7, and 37.3 g kg–1, respectively for the same treatments. These findings indicated that the Tillage treatment exhibited lower soil organic matter content and reduced bioavailability of some nutrients, which raises concerns about its sustainability. On the contrary, employing Sheep Walking with an appropriate stocking rate, effectively controlling vegetation in the spring, ensured favourable soil properties and olive yields comparable to the other treatments. Moreover, the Sheep Walking approach provides supplementary advantages to the farmer, including revenue from the sale of animal products and the opportunity to transition to organic farming systems, which better align with the preferences of contemporary societies.

The paper attempts to explore the relationship between federalism and rural development. Federalism is a division of power, responsibility and accountability to bring the administrative and political power closer to the ground and essentially to increase the good governance. On the other hand, rural development is a complex and multidimensional issue- especially much demanding for least developed and developing countries. A descriptive and qualitative approach was carried out to study the complex relationship between rural development and federalism. Similarly, a SWOT analysis was carried out to have a better understanding of the relationship. The study found that there is significant potentiality for accelerated development of rural landscape in federalism if carefully executed. However, on the other hand, federalism may pose several risks on rural development and may restrict the development pace if not executed with appropriate care and understanding. Therefore, the study concludes that cooperation and coordination among the federal structures are crucial for better development of the rural economy.

Mustard, a widely used condiment, is derived from mustard seeds and partially defatted mustard flour. Varieties of mustard are primarily distinguished by the ratios of mustard seeds and spices used in their production. This study assessed the microbiological safety of mustard products from the Mustard and Ketchup Factory in Poland, produced between 2019-2021, in compliance with Polish and EU regulations. Three mustard types were analyzed: gourmet, creamy, and spicy, crafted from 'Borowska' white mustard and 'Małopolska' Sarepta mustard seeds. The preparation included powdered mustard seeds, water, sugar, and vinegar. Samples of mustards (20 g each) were tested in triplicate for Salmonella, spore-forming anaerobic bacteria, coliform bacteria, Staphylococcus aureus, mold, and yeast. Additionally, water and spices used in production were analyzed for total coliforms, Escherichia coli, Enterococcus, Salmonella, aerobic mesophilic microorganisms, anaerobic spore-forming bacteria, and mold. Results indicated that spices and water met all microbiological criteria. Mustard samples tested negative for Salmonella and anaerobic spore-forming bacteria, with coliforms, Staphylococcus aureus, mold, and yeast counts within acceptable limits, ensuring compliance with food safety and hygiene standards. This research underscores the importance of ongoing monitoring and strict microbiological standards to maintain food safety. Future studies should develop advanced microbial detection methods and implement robust quality control measures to reduce contamination risks in mustard and other food products.

Fine dust causes various disorders, including cardiovascular, neurological, renal, reproductive, motor, systemic, respiratory, and cancerous diseases. Therefore, it is necessary to study functional materials to prevent these problems. In this study we used various methods, including quantitative PCR, flow cytometry, ELISA, and Alizarin O staining, to study the beneficial effects of erucic acid against fine dust. Erucic acid and erucic acid-induced exosomes (EIE) strongly suppress the attenuation of osteocytic differentiation and inflammation induced by fine dust. Erucic acid effectively suppresses inflammation in fibroblasts exposed to fine dust. Notably, despite exposure to fine dust, EIE promoted osteocytic differentiation in adipose-derived stem cells (ASC) and osteogenesis in macrophages, in addition to phagocytosis. Dramatic upregulation of RunX2 and BMP7 by EIE indicates that it is a strong activator of osteocytic differentiation in ASC and protects them from the effects of fine dust. Moreover, EIE induces immune activity and acts as an osteogenic trigger for macrophages. Therefore, this study suggests the potential use of erucic acid and erucic acid-induced exosomes (EIE) as biomaterials to prevent environment-borne diseases.

Poultry farming in Slovakia has a tradition and an irreplaceable position to ensure rational nutrition for the population. In terms of a nutritional value, poultrymeat (Galliformes) contains a high amount of proteins, essential amino acids, essential unsaturated fatty acids, minerals, vitamins and a low fat content. Poultrymeat production has a relatively short reproductive cycle and thus allows regulating the demand and supply. The poultry market also influences the development of domestic consumption. According to the Statistical Office of the Slovak Republic, the consumption of meat has witnessed a persistent increase over the last 10 years. [1] According to the 2023 AVEC (The Voice of European Meat Sector) annual report, the consumption of poultrymeat in Slovakia was 20.0 kg per person per year. The average consumption in the EU-27 (2021) was 23.4 kg, with the countries with the highest consumption being Portugal (37.8 kg), Ireland (36.0 kg), Hungary (33.5 kg) and Spain (29.9 kg). On the other hand, the countries with the lowest consumption of poultrymeat, apart from Slovakia, also include Austria and Greece with a consumption of 21.5, resp. 21.0 kg [2]. The breeding of broiler chickens, as well as the production and placing on the market of poultrymeat must comply with the requirements laid down by legislation, while the compliance is regularly checked by the competent authorities.

With a view to understand and resolve the complexity of the food matrix, ohmic technologies alone or in combination were extensively employed. In this sense, the newest developments and advances of proteomics, metabolomics, lipidomics whith their unique benefits could simplify and understand the link between physiological and pathological activities in biology, physiology, pathology, and food science and processing. This review aims to briefly introduce the basis of proteomics, metabolomics, lipidomics, then expansively review their impact on the assessment of meat quality and safety. Here, also, we discuss the application of proteomics, metabolomics, lipidomics for the authentication and adulteration of meat and meat derivatives from different sources, and provides some perspectives regarding the use of emerging techniques such as rapid mass spectrometry (MS) and non-invasive measurements for the analysis of meat quality and safety. This paper summarizes all significant investigation in these matters, and underlines the advances in analytical chemistry technologies and meat science areas. By emphasizing the requirement for additional examinations, this paper attempts a comprehensive knowledge of “foodomics” and their potential to improve their employment in meat science.

Promoting the sustainable development of resource-based cities is of great significance to the ecological protection and high-quality development of the Yellow River Basin. Combining the environmental status and economic development, we objectively evaluate the ecological safety level of resource-based cities in the Yellow River Basin, compare and analysis the main factors affecting the ecological safety of different resource-based cities, and formulate precise and differentiated ecological safety protection measures in river basins to achieve high-quality development. Taking the Yellow River Basin as an example, this paper analyses the ecological level of the Yellow River Basin based on the theory of sustainable development, calculates the ecological safety level of 30 resource-based cities in the Yellow River Basin from 2006 to 2020 by TOPSIS model, and makes convergence analysis by classification. Through the DID empirical test of sustainable development planning policy on ecological safety factors, distinguish the development characteristics of different resource-based cities. The results show that: (1) the ecological safety level of resource-based cities in the Yellow River Basin is generally developing well, and there are differences among different types of resource-based cities; (2) the kinetic energy of sustainable development of resource-based cities in the Yellow River Basin is mainly industrial transformation, and the power of science and technology is insufficient; (3) local governments pay limited attention to environmental protection, and the sustainable development planning of resource-based cities in 2013 mainly promotes the adjustment of industrial structure of resource-based cities.

Using the limits of a specific watershed (river basin) to establish boundaries of precise rural and urban intervention strategies, can conduce to a better understanding of the dynamics between natural hydro-morphology of a hydrological region, water infrastructures (damns, canals, reservoirs) and urban and rural fabric. To perform watershed-based planning approaches with valuable indicators is necessary to generate hybrid cartographies combining urban, architectural, agricultural and hydrological boundaries. In some countries, the necessary information to produce these cartographies is not available; however, is possible to create fundamental layers using GIS software and national geospatial information and subsequently perform algorithmic calculations in the same software. Once these cartographies are developed and analyzed for a determined basin is possible to observe scenarios where rural and urban planning are better suited for precise hydric-urban restoration. In the following article a series of hybrid cartographies are presented. These types of maps are useful for interpretation of water usage flow in rural communities and their agricultural productive surfaces, and ultimately for analytical purposes in dealing with hydrological alterations of the water cycle. The diagnostic results can be used to develop specific rural interventions for fluvial restoration in territorial contexts, and improvement on hydrological infrastructure and the hydrological region water network.

Reducing the levels of toxic chemicals that cause adverse health and environmental impacts is a challenge for the international community. There is a need of a global strategy. Indeed, too often the problems associated to the exposure of chemical substances is recognized a posteriori, in the presence of consequences already observed. The prediction of the likely effects of chemical exposure on human health is based on classical tests with animals, which are time and money consuming, may deviate from an accurate prediction towards humans, and arises ethical concerns. Regulations are now considering the adoption of in silico (or computational) methods, which can be used for prioritizing substances according to the probability to be toxic for the biosphere. Several initiatives have prioritized chemicals, typically based according to some criteria, such as chemicals which may be endocrine disruptors, or persistent, bioaccumulative, or toxic (PBT). However, these initiatives focused on a certain range of adverse properties, and covered a certain number of substances only. We applied a set of largely validated and widely used predictive methods to large collections of chemicals: (i) to about 340,000 with a defined function, and (ii) to about 6 millions, which have been synthetized. The aim of this study is to quantify the putative impact of existing and future chemicals on towards human health, ecological and environment properties. The impact on the environment is the cause of major concern. This is the case of pesticides and hazardous, which is quite expected; however, also pharmacologically active candidate compounds of natural origin may have a high level of ecotoxicity. Pesticides and hazardous are also the categories of higher concern for humans, followed by pharmaceuticals. The pesticides and the hazardous are the categories of higher concern also on the environmental point of view. The results of our analysis could be the basis for the identification of new safety rules.

Background/Objectives: The aim of this study was to investigate feasibility and safety of neuromuscular electrical stimulation (NMES) in patients on extracorporeal membrane oxygenation (ECMO) and assess thoroughly any potential adverse events. Methods: We conducted a safety and feasibility study including 16 ICU patients on ECMO support who were admitted to the cardiac surgery ICU from January 2022 to December 2023. Patients underwent a 45-minute NMES session, still on ECMO support, that included a warm up phase of 5 minutes, a main phase of 35 minutes and a recovery phase of 5 minutes. NMES was implemented on vastus lateralis, vastus medialis, gastrocnemius and peroneus longus muscle of both lower extremities. Two stimulators delivered biphasic, symmetric impulses of 75 Hz, with 400 μsec pulse duration, 5 sec on (1,6 sec ramp up and 0,8 sec ramp down) and 21 sec off. The intensity levels aimed to cause visible contractions and be well tolerated. Primary outcomes of the study were feasibility and safety, evaluated by whether the NMES sessions were successfully achieved, and by any adverse events and complications. Secondary outcomes included indices of rhabdomyolysis from biochemical blood test, 24 hours after the application of NMES. Results: All patients successfully completed their 45-minute NMES session, without presenting hemodynamic deterioration, adverse events or signs of rhabdomyolysis. The majority of patients achieved type 4 and 5 quality of muscle contraction. Conclusions: NMES is a safe and feasible exercise methodology in patients supported with ECMO.

The introduction of any new disruptive technology in a traditionally well-established industry, such as the road construction industry, is usually associated with considerable resistance. This is especially relevant when the new technology is based on the use of granular materials traditionally considered to be of an unacceptable quality in combination with relatively new concepts such as New-age (Nano) Modified Emulsions (NME). In such cases, the fact that the material design methods are based on fundamental scientific principles and have been proven in laboratories and through Accelerated Pavement Testing (APT), may be of little influence. However, the general acceptance of new disruptive technologies, e.g. telecommunications and Information Technologies (IT), have been based on the considerable advantages it presented. The same principles are applicable to the general acceptance and use of NME stabilisation/enhancement of materials in the road construction industry. This article is aimed at the practical cost-effective demonstration of the general application of the use of nanos-silane modified emulsions in the construction of the highest order roads, i.e. inter-city multi-lane highways, lower order roads (including Low-Volume-Roads (LVR)) and even local accesses to farms and in villages/townships. The implementation of NME technologies is directly associated with ease of use, time and cost savings and the addressing and reduction of risks applicable to the use thereof.

Asthma is a significant public health concern. This study identified the provinces with the highest morbidity and mortality rates due to asthma among the working-age population (15-69 years) in the Republic of Ecuador. The secondary objective was to explain the possible differences attribut-able to occupational exposure. This nationwide ecological and exploratory study was conducted in 24 provinces between 2016 and 2019. Government databases were used as sources of infor-mation. Standardized rates were calculated for codes the J45 and J46. The hospitalization mor-bidity rate for asthma decreased from 6.51 to 5.76 cases per 100,000 working-age population, and the mortality rate has consistently been low and stable from 0.14 to 0.15 deaths per 100,000 working-age population. Geographic differences between the provinces were evident. The risk of hospitalization and death due to asthma was higher in the Pacific coast (five provinces) and the Andean region (two provinces). The high rates observed in provinces with greater agricultural and industrial development could be the main determinants of national heterogeneity and could act as occupational risk factors. The contribution of occupational hazards in each province should be examined in depth through ad hoc studies. These findings provide valuable information for creating public policies aimed at promoting and safeguarding the respiratory health of the popu-lation, particularly that of workers.

Obesity poses significant challenges in rural communities worldwide due to limited resources and healthcare access. Practical, innovative, and culturally sensitive approaches are essential. Time-Restricted Eating (TRE), aligning food intake with circadian rhythms, emerges as a promising strategy. By restricting eating to specific time windows, TRE synchronizes with the body's internal clock, offering potential metabolic health benefits. This review examines TRE's potential in rural obesity management, highlighting its simplicity and scalability. While TRE may address rural health disparities, cultural considerations and challenges such as undernutrition must be acknowledged for effective implementation. Overall, TRE shows promise in improving metabolic health and well-being in rural populations.