The sand-dust horizontal flux is an important parameter for the study on aeolian sand transport, as well as an important foundation. In this study, a field experiment was developed to measure the data of aeolian transport and microclimate during different dust events with an auto sand sampler, a piezoelectric saltation sensor (H11-Sensit) and a 10 m high meteorological tower in Ta Zhong, the hinterland of the Taklimakan Desert from July to August in 2010. Then, the sampling efficiency of auto sand sampler and horizontal dust flux of near surface were analyzed based on observed data. The results were as follows: sand collector skip turnover increased with the increase of the intensity of dust weather frequency increases, the power function relationship y=2.115 x0.9841, R2 = 0.9206, flip frequency per minute increased from 0.2794 times to 1.3041 times, change is obvious; With the strength of the weather, time to flip the average sediment is shrinking. Sandstorm weather, skip to flip a volume of 3.7160 g, grade I flying sand weather flip a volume of 4.0275 g, the amount of class II flying sand weather turns over a 5. 0035g.The horizontal dust flux of different dust events that calculated with the equation Q=256M; the maximum of one dust event was about 190.335 kg, and the minimum was 1.2 kg. Overall, the sand transportation rate increased with wind speed. However, the changes of sand transportation rate did not quite fit in with wind speed during some dust events, and in this case the corresponding surface temperature was significantly higher. The experimental data obtained can provide theoretical basis for regional sand control and enacting effective engineering measures.

This study analyzes the relevance of governance structure for efficiency in revenue collection by Brazilian Water Utilities (WUs). Data was collected from the National Information System on Sanitation (SNIS) for 127 Brazilian WUs, covering a balanced longitudinal panel from 2018 to 2022. Governance structures evaluated included Ownership (public or private) and Corporatization (publicly traded or not). In scientific databases, we did not find studies on the efficiency of specific WUs in collecting customer bills for services rendered and its relationships with this type of governance; thus, this would be the main innovative contribution of the study to the previous literature. In the first stage, the study utilized the Dynamic Slack Based Model (DSBM) to assess revenue collection efficiency. In the second stage, an econometric model with Generalized Estimating Equations (GEE) to explain the efficiency. The findings revealed a global average inefficiency of 50.47% in revenue collection. Corporatization was linked to higher collection efficiencies, while ownership type was significant, but with lower collection efficiency. Factors such as tariff accessibility, urbanization, and the COVID-19 pandemic also influenced efficiency. The study suggests regulatory bodies should consider these insights to implement policies that prevent inefficiencies from affecting the tariff system for services.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Debt collection companies buy overdue debts on the market in order to collect them and recover the highest possible amounts of a debt. The pursuit of debt recovery by employees of collection agencies is a very demanding task. The aim of the article is to propose a rule-based model for managing the process of mass debt collection in a debt collection company, which will make the debt collection process more efficient. To achieve this, we have chosen a decision tree as a machine learning technique best suited for creating rules based on extensive data from the debt collection company. The classification accuracy of the decision tree, regardless of the possibility of acquiring rule-based knowledge, proved to be the highest among the tested machine learning methods, with an accuracy rate of 85.5%. Through experiments, we generated 16 stable rules to assist in the debt collection process. The proposed approach allows for the elimination of debts that are difficult to recovery at the initial stage of recovery process and to decide whether to pursue amicable debt collection or to escalate the debt recovery process to legal action. Our approach also enables the determination of specific actions during each stage of the proceedings. Abandoning certain actions or reducing their frequency will alleviate the burden on collection agency employees and help avoid the typical burnout associated with this line of work. This is the path to making the organizational culture of a collection agency more sustainable. Our model confirms also the possibility of using data from debt collection companies to automatically generate procedural rules and automate the process of purchasing and collecting debts. However, this would require a larger set of attributes than what we currently possess.

Companies are increasingly focusing on sustainable business practices. Internal and external stakeholders’ expectations manifest in legal requirements, national and international standards, and market and customer expectations, among other things, must be considered. In addition to profit maximization as the usual target for corporate management, management must consider environmental sustainability aspects such as resource efficiency, greenhouse gas intensity, and a company's emissions behavior. In addition, social aspects relating to the company's employees, the immediate urban environment, the situation in the supply chain, and effects on the market environment must increasingly be considered. Specifically, companies are faced with the chal-lenge of dealing with conflicting objectives regarding the various aspects of sustainability and, if necessary, weighing them up against each other. These trade-offs must be made against the company's socio-economic and ecological environment, corporate strategy, and sustainability goals. This paper provides an overview of current approaches and research gaps on this topic through a literature review. It shows a lack of methods and frameworks to specifically deal with trade-offs and conflicts of goals.

Plant biotechnology is dependent today on accessing broader plant genetic resources for food and agriculture (PGRFA) diversity for ensuring food security for our future. Heterogenous agricultural lands are considered today as hotspot for biodiversity, and they also exist in the hilly mountain areas of Romanian’s Carpathians. The scope of this review is to describe traditional home-hardens related to the land use of households and cultivated species from Moșna commune, Sibiu County, Romania. The survey was realized with the support of authorities and local stakeholders from 2010 up to 2019. The results of this survey revealed that maintenance of crop species structure and land use of traditional households is longer than 100 years. Consequently at least 15 traditional Saxon home-gardens of 120 taken into the study may be defined. Today these home-garden covers a media of 26% of the total area of a household and should be part of a surface ranging between 5,000 and 1,500 m2. The first Local Council Decision in Romania in 2019 supporting the recognition of landraces and home-gardens as heritage values was officially adopted supporting the need to more access bottom-up approaches for supporting biodiversity conservation.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

To facilitate the computation of the uniaxial compressive strength value of the cemented paste backfill under the condition of high sand-cement ratio, and to analyze the size effect of the cemented paste backfill with high sand-cement ratio under varied aspect ratios, the cemented paste backfill specimens with sand-cement ratios of 8:1-24:1 and aspect ratios of 0.5, 1, and 2 were prepared. Through response surface experiments and finite element analysis, the influence of three aspect ratios on the cemented paste backfill strength was explored, and the failure characteristics and size effect mechanisms of cemented paste backfill with various aspect ratios were analyzed. The model of strength conversion between cemented paste backfill with different aspect ratios was established. The results show that the compressive strength of the cemented paste backfill decreases with the increase of the aspect ratio under the same mass concentration and sand-cement ratio. When the aspect ratio is 0.5 and 1, the splitting failure is the main factor; when the aspect ratio is 2, the shearing failure is the main factor. The three-dimensional stress caused by the end effect of the cemented paste backfill is the main reason for the high strength when the aspect ratio is 0.5. Due to the one-dimensional stress zone generated in the middle of the cemented paste backfill with an aspect ratio of 2 in the laboratory, its strength value is closer to the actual uniaxial compressive strength value of the cemented paste backfill. The strength values of the cemented paste backfill with aspect ratios of 0.5 and 1 were higher than the actual uniaxial compressive strength values in the laboratory. The rationality of the theoretical analysis was verified by the ABAQUS analysis results. According to the experimental results, a strength conversion model between different aspect ratios is established, which can provide a reference for the design of the uniaxial compressive strength of the cemented paste backfill.

In recent experimental studies, we reported the aggravating effects of Asian sand dust (ASD) on male reproductive function in mice. However, the effects of fetal ASD exposure on male reproductive function have not been investigated. The present study investigated the effects of fetal ASD exposure on reproductive function in male offspring. Using pregnant CD-1 mice, ASD was administered intratracheally on days 7 and 14 of gestation, and the reproductive function of male offspring was determined at 5, 10, and 15 weeks after birth. The secondary sex ratio was significantly lower in the fetal ASD-exposed mice than in the controls. Histologic examination showed partial vacuolation of seminiferous tubules in immature mice. Moreover, daily sperm production (DSP) was significantly less in the fetal ASD-exposed mice than in the controls. DSP in the fetal ASD-exposed mice was approximately 10% less than the controls at both 5 and 10 weeks. However, both the histologic changes and the DSP decrease were reversed as the mice matured. These findings suggest that ASD exposure affects both the fetal development and the reproductive function of male offspring. In the future, it will be necessary to clarify the onset mechanisms of ASD-induced male fetus death and male reproductive disorders.

Concrete contributes 8% of all global carbon emissions making the need to find substitute critical for environmental sustainability. Research has indicated the potential for recycled plastics to be used as concrete substitutes. This study extends existing research by investigating the use of polycarbonate (PC) in plastic sand bricks as a mechanical equivalent to concrete. PC has high compressive strength, durability, impact strength, thermal resistivity, clarity, fatigue resistance, and UV resistance. This work provides a method and mold to produce a matrix of sand-plastic sample compositions with dimensions adhering to ASTM D695 standard for compressive properties of rigid-plastic. Compositions of 0% (control), 20%, 30%, 40%, and 50% sand by weight were tested. Samples were tested for compressive strength until yield and stress-strain behaviors plotted. The results for 100% PC demonstrated an average and maximum compressive strength of 71 MPa and 72 MPa, respectively. The 50% PC and 50% sand composition yielded an average and maximum compressive strength of 71 MPa and 73 MPa respectively with an increase in compressive stiffness, and transition to shear failure resembling cement. With a composite density of 1.86 g/cm3 against concrete’s average 2.4 g/cm3, and a compressive strength exceeding commercial concrete demands of 23.3 MPa to 30.2 MPa, this lightweight alternative meets the strength demands of concrete, reduces the need for new construction materials, and provides an additional recycling opportunity for nonbiodegradable waste plastic.

In order to improve the charge collection efficiency, we simulated and experimentally tested the doping structure of the electron multiplication layer in EBCMOS. In this paper, we simulate the charge collection efficiency of EBCMOS under different doping methods by modeling the collisional scattering of electrons with solid atoms in semiconductor materials and combining the transport trajectories of electrons in the electron multiplication layer, the simulation results indicate that using a layered doping structure to reduce the thickness of the index heavily doped layer can effectively optimize the electric field distribution in the electron multiplier layer and reduce the recombination rate of electrons. The optimized doping structure has a significant effect on improving charge collection efficiency. Based on the simulation results, doped samples were prepared and tested. The test results showed that the charge collection efficiency obtained under the condition of a P-type silicon substrate thickness of 7μm and an index heavily doped layer thickness of 1μm was 72.65%, reducing the thickness of the index heavily doped layer to 0.1μm, the charge collection efficiency obtained can reach 86.27%, which proves that reducing the thickness of the index heavily doped layer can effectively improve the charge collection efficiency of EBCMOS devices.

The rock joint fissure slope in cold regions is prone to deformation and failure problems such as relaxation, tension and collapse under freeze-thaw (F-T) cycles. Based on the ideology of clean production and promoting the structural integrity of geotechnical projects in cold areas, this study designed and prepared aeolian-sand (AS) to replace part of river sand as a filling mortar material by taking advantage of the low cost and easy availability of AS. Investigations were carried out to determine the impact of varying proportions of AS in mortar on the microstructure and shear properties of the mortar-rock interface under F-T cycles. Therefore, F-T cycle testing, nuclear magnetic resonance (NMR) testing and shear testing were carried out on grout with different proportions of AS. The results show that the right proportion of AS replacement could enhance the shear deformation resistance and F-T resistance of the mortar-rock interface, and 30% proportion is the optimal proportion. By increasing of F-T cycles, the three types of specimens showed different degrees of particle spalling, shedding and cracking. The slurry-rock interface layer in the A (0%) group exhibited the most severe F-T deterioration, while the B (15%) group showed a lesser degree, and the C (30%) group performed the best. T2 spectrum curve and total spectrum area change law from the microscopic point of view to verify the 30% AS proportion mortar-rock interface F-T resistance is the strongest, followed by 15% AS proportion mortar, the weakest is ordinary mortar. The degradation of the mortar-rock bond is primarily due to the conversion of solid to liquid phases and the movement of internal water caused by fluctuating temperatures. The extent of F-T deterioration in the slurry-rock interface layer is greatly affected by the varying proportions of AS. The shear strength and shear stiffness of specific proportion of AS decreased with the increase of F-T cycles. For same F-T cycles, the shear strength and shear stiffness of group C (30%) were the highest, followed by group B (15%) and group A (0%). The grout material not only reinforces the F-T joint fissure slope, but also reduces the cost of grout reinforcement and promotes the clean production of geotechnical structures.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

The scientific community has shown considerable interest in Industry 4.0 due to its capacity to revolutionise the manufacturing sector through digitalisation and data-driven decision-making. However, the actual implementation of Industry 4.0 within complex industrial settings presents obstacles that are typically beyond the scope of mainstream research articles. In this paper, a comprehensive case-study detailing our collaborative partnership with a leading medical device manufacturer is presented. The study traces their evolution from a state of limited digitalisation to the development of a digital intelligence platform that leverages data and machine learning models to enhance operations across a wide range of critical machines and assets. The main business objective was to enhance the energy efficiency of the manufacturing process, thereby improving its sustainability measures while also saving costs. The project encompasses energy modelling and analytics, Fault Detection and Diagnostics (FDD), renewable energy integration and advanced visualisation tools. Together, these components enable informed decision making in the context of energy efficiency.

This study aims to analyse the technical viability and economic feasibility of rainwater harvesting systems for single and multifamily residential buildings in the city of Florianópolis, Brazil. Simulations were conducted for representative buildings in the city under different water usage scenarios and system designs, in a total of 36 simulation scenarios. An economic analysis was performed for four scenarios over a twenty-year period. Both initial and operational costs were considered and net present value, internal rate of return and payback used as feasibility indicators. Almost all of the cases simulated were technically viable for the group of houses, and up to 78.9% for flats. As for the economic analysis, for houses, between 60.1% and 74.8% of the cases were economically feasible, achieving a discounted payback period ranging from 6.2 to 8.6 years. For flats, between 57.8% and 64.2% of the cases were economically feasible, achieving a discounted payback period ranging from 4.8 to 5.6 years. As the water tariff in the city underwent changes recently, the former and current tariff formats were compared. The current tariff format provides more economic benefits for saving potable water, and leads to a higher net present value and a shorter discounted payback period.

Recycling waste products is an environmental-friendly activity that can bring benefits to accompany, saving manufacturing costs and improving economic efficiency. For the beer industry, recycling bottles can reduce manufacturing costs and reduce the industry's carbon footprint. This paper presents a model for a multi-objective collection-distribution center location and allocation problem in a closed loop supply chain for the beer industry, in which the objective is to minimize total costs and transportation pollution. Uncertainties in the form of randomness and fuzziness are jointly handled in this paper to ensure a more practical problem solution, for which returned bottle sand unusable bottles are considered fuzzy random variables. A heuristic algorithm based on priority-based global-local-neighbor particle swarm optimization (pb-glnPSO) is applied to ensure reliable solutions for this NP-hard problem. A case study on a beer operation company is conducted to illustrate the application of the proposed model and demonstrate the priority-based global-local-neighbor particle swarm optimization.

Genetic enhancement of grain production and quality is a priority in wheat breeding projects. In this study, we assessed two key agronomic traits - grain protein content (GPC) and thousand kernel weight (TKW) - across 179 Bulgarian contemporary and historic varieties, and landraces in three growing seasons. Significant phenotypic variation existed for both traits among genotypes and seasons, and no discernible difference was evident between the old and modern accessions. To understand the genetic basis of the traits, we conducted a genome-wide association study with MLM using phenotypic data from the crop seasons, best linear unbiased estimators, genotypic data from the 25K Infinium iSelect array, and a Bonferroni-adjusted p-value. As a result, 776 significant quantitative trait nucleotides (QTNs) organized into quantitative trait loci were discovered, including 25 loci associated with GPC, and 35 loci linked to TKW. Additionally, 14 environmentally stable QTNs were identified for TKW. Certain loci on chromosomes 2A, 3A, and 6B favorably in-fluenced GPC, while the locus on chromosome 6D impacted TKW positively. These loci may reflect novel associations to the two traits. Annotations for proteins involved in the remobilization of carbon and nitrogen from vegetative tissues to developing grain during senescence, as well as in the following buildup of resources required for seed germination, have been found for selected pu-tative candidate genes. These include genes coding for 11S globulin seed storage protein, glutamine synthetase, metalloendopeptidase, components of the ubiquitin/proteasome system, sucrose transporter, alpha-amylase, NAC and bZIP transcription factors. Our findings highlight promising genomic regions for targeted breeding programs aimed at improving grain yield and protein content.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

A unified critical state model has been developed for both clean sand and silty sand using the modified Cam-clay model (MCC). The main feature of the proposed model is a new critical state line equation in the e-ln(p) plane that is capable of handling both straight and curved test results. With this feature, the error in calculating plastic volumetric strain is eliminated in theory. Another crucial feature of the model is the transformed stress tensor based on the SMP (spatially mobilized plane) criterion, which takes into account the proper shear yield and failure of soil under three-dimensional stresses. Additionally, the proposed model applies the intergranular void ratio with the fines influence factor for silty sand. Only eight soil parameters are required for clean sand, and a total number of twelve soil parameters are needed for silty sand.

A regional modern river-sand geochemical mapping study in the majority of the Timor-Leste territory, including the research area, has not been previously reported. This study demonstrated the potential of modern river sand geochemical mapping as an effective method for lithological mapping, particularly in areas that face challenges in conducting efficient geological fieldwork and have limited geological information. A total of 53 modern river sand samples were collected and analyzed. Before examining the samples using wavelength-dispersive X-ray fluorescence for ten major elements, the loss-on-ignition method was employed. In the Clerec drainage basin, SiO2, CaO, and K2O showed positive correlations, and CaO was positively correlated with MnO. Similarly, in the Sahe River catchment, a positive relationship was observed between CaO, MnO, and TiO2. These findings suggested the presence of quartz, manganese, secondary K-bearing minerals, and secondary Ti-bearing minerals in carbonate rocks that have undergone silicification and other alteration processes. The principal component analysis results corroborated the SiO2/Al2O3 and K2O/Na2O ratios and the ICV findings. PC1 was related to the variations in Ca-poor and Ca-rich rocks; PC2 indicated notable inputs from SiO2-rich and SiO2-poor rocks; and PC3 revealed the possibility of contributions from secondary mineral assemblages related to silicification and low-grade metamorphic processes.

Transportation systems through the ages have seen drastic evolutions in terms of transportation methods, speed of transport, infrastructure, technology, connectivity, influence on the environment, and accessibility. The massive transformation seen in the transportation sector has been fueled by the industrial revolutions which have continued expansion and progress into the fourth industrial revolution. However, the methodologies of data collection and processing used by the many drivers of this progress differ. The significance of standardized data and its mode of collection cannot be overstated as it has a major impact on the process outcomes. In order to achieve a better understanding of the impact of this, this study methodically reviewed the literature on the subject of the data collection and processing mechanism of 4IR technologies in the context of the transport industry with an emphasis on the areas of accomplishment of several studies and drawing attention to their limitations. Although the industry has advanced significantly as a result of the adoption and application of various research studies in this field, considerable focus needs to be placed in the areas of standardized data collection and computational approaches, which will ultimately assist in achieving various benefits in the transportation industry.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

This paper investigates the improvement in solar energy collection and conversion using Al₂O₃-Water nanofluids in a solar flat plate collector (SFPC). The efficiency of a solar flat plate collector using water as the fluid medium is analyzed experimentally and theoretically. For theoretical analysis, a mathematical model in MATLAB is used to simulate and is validated by the experimental results. To enhance the solar energy collection and conversion efficiency of the SFPC, Al₂O₃-Water nanofluid was selected as the fluid medium. The nanofluid properties like density, specific heat capacity, thermal conductivity and viscosity are analyzed and compared for several models of Al₂O₃-Water nanofluids and the best model was selected to modify the simulation. Effect of particle diameter in the nanofluid was found to be marginal on the nanofluid properties. The optimum volume concentration of the nanofluid was found to be 4% giving an efficiency increase of 7.78% in the SFPC over the use of water. This reduces the area of the SFPC by 10.5%.

The use of cemented aeolian sand-fly ash backfill (CAFB) material to fill the mining area to improve the surface subsidence damage caused by underground coal mining is in the development stage. Their performance with large overflow water and strength loss is not well understood. Few research has been conducted to understand the effects of aeolian sand and coal gangue on the rheological properties of CAFB with plasticizers. Therefore, the aim of this study is to investigate the effects of a plasticizer on the rheological properties, specifically yield stress and viscosity, of CAFB prepared with aeolian sand and coal gangue. CAFB mixes containing 0%, 0.05%, and 0.1% plasticizer were prepared, and yield stress and viscosity were determined at different time intervals over the period. Additional tests, such as thermal analysis and zeta potential analysis were also conducted. It was found that the rheological properties of CAFB is the comprehensive manifestation of the composite characteristics of various models. Reasonable particle size distribution and less amount of plasticizer can ensure the stability of slurry structure, reduce the slurry settlement and the risk of pipe blocking. The findings of this study will be beneficial in the design and production of CAFB material.

The article presents the results of cyanide leaching of gold-containing concentrate using the trichlorocyanuric acid (TCCA) oxidizer. Gold-containing concentrate obtained from a gold tailings sample from a gold recovery factory (GRF) in one of the deposits of Kazakhstan that was not previously studied for concentrability. According to X-ray phase analysis and energy dispersive spectrometry (DSM) data, the main compounds in the tailings sample under study are: pyrite FeS2, quartz SiO2, calcite CaCO3, albite NaAlSi3O8, muscovite KAl2Si3AlO10(OH)8, dolomite CaMg(CO3)2, and oxidized iron compounds. Microscopic studies have established the presence of gold grains in free form, ranging in size from 0.9-10.2 mkm Au-ultrafine and fine gold. Obtaining a gold-containg concentrate with a gold content of 15.95 g / t is possible according to the enrichment scheme, which includes centrifugal separation, classification according to the fineness class -0.05 mm, additional grinding of hydrocyclone sands to a fineness of 90.0-95.0% of the class finer than 0.050 mm, and control centrifugal separation. Since pyrite in technogenic raw materials is the main gold-containing mineral, this paper presents studies on the oxidizability of pyrite with the TCCA oxidizer. The results of studies on the oxidation of pyrite using the TCCA oxidizer show that the products of its hydrolysis oxidize pyrite with the formation of various iron compounds on its surface. Pretreatment of gold-containing concentrate with oxidizer TCCA for 3 hours before the cyanidation process (20 hours) allows to increase the recovery of gold in the solution by 5.8 %.

This paper analyzes the collection of George Viau (1855-1939) from a computational perspective. Indeed, this dental surgeon, close to the Impressionists, collected several hundred works of art in the first half of the 20th century: the auctions of his collection, in 1907, 1930 and after his death, in 1942, 1943 and 1948, accounted for 642 artworks and, during the Occupation, the 1942 sale produced a total of more than 46 million francs. Thanks to statistics, econometrics, network analysis and cartography, it is possible to understand the salient features of the collection and its place in the world of Parisian auctions.

The article presents the results of tests of minor head losses through PVC and PP elbows for a flow of water and mixtures of water and sand with grain sizes of up to 0.5 mm and concentrations of 5.6 g∙L-1, 10.84 g∙L-1, and 15.73 g∙L-1. The tests were carried out at variable flow velocities for three elbow diameters of 63, 75, and 90 mm. The flow rate, pressure difference in the tested cross-sections, and temperature of the fluids were measured and automatically recorded. The results of the measurements were used to develop mathematical models for determining the minor head loss coefficient as a function of elbow diameter, sand concentration in the liquid, and Reynolds number. The mathematical model was developed by cross validation. It was shown that when the concentration of sand in the liquid was increased by 1.0 g∙L-1, the coefficient of minor head loss through the elbows increased, in the Reynolds number range of 4.6∙104 − 2.1∙105, by 0.3−0.01% for PP63, 0.6−0.03 % for PP75, 1.1−0.06 % for PP90, 0.8−0.01 % for PVC63, 0.8−0.02 % for PVC75, and 0.9−0.04 % for PVC90. An increase in Re from 5∙104 to 2∙106 for elbows with diameters of 63, 75 and 90 mm caused a 7.3 %, 6.8 %, and 6.0 % decrease in the minor head loss coefficient, respectively.

The changing of banking customer preferences after Covid-19 pandemic encourages banking transformation. Neobanks emerges as innovation in banking that enter the market to compete with the incumbent banks by offering new digital experience for customer. This paper analyzes the neobanks which transformed from traditional bank, specifically its efficiency after they implement digital transformation. Efficiency is measured by using Stochastic Frontier Analysis (SFA). This study also uses Pooled Mean Group (PMG) of Panel ARDL (Autoregressive Distributed Lagged) to investigate digital transformation as one of determinants neobank’s efficiency, as well as to examine the existence of short-term and long-term relationship between digital transformation and efficiency. The SFA results show that the efficiency of the neobanks increase after they carry out digital transformation. Furthermore, from PMG Panel ARDL, it can be concluded that digital transformation is one of determinant of efficiency and there is longevity relationship between digital transformation and efficiency. In the short run, digital transformation has a significant and negative correlation with efficiency and in the long run, it has a significant positive relationship because initially digital transformation cost for operational and risk management innovation decreases the profit efficiency, but afterwards it increases the profit efficiency.

A herbarium is a library of preserved dried samples of vascular plants, bryophytes, fungi, algae and/or lichens and is maintained for educational and scientific purposes, and provides detailed information on taxonomy, systematic, biodiversity, ecological and evolutionary research studies. Globally, there are more than 3,000 active public herbaria that preserve around 400 million exsiccates. In Brazil there are 216 active herbaria, of which 162 are indexed in the Index Herbariorum and in the Central region there are 21 herbaria. In this context, the Herbarium of the University of Brasília (international code UB) was founded in 1963 together with the Department of Botany of UnB and is located at the Institute of Biological Sciences of the Campus Darcy Ribeiro, Brasília and it is fifth largest herbarium in Brazil and presents approximately 277 thousand samples. In this study, we present here the bryophytes collection at the UB Herbarium. The collection of bryophytes of UB herbarium has 30,902 samples of all continents and 79 countries and most come from Brazil, Papua New Guinea, Malaysia, United States of America and Argentina.

The valorization of the large amount of crude glycerol formed from biodiesel industry, is of primordial necessity. One possible direction with high interest to the biorefiniery sector is the production of fuel additives as solketal, though the acetalization of glycerol with acetone. This is a chemical process that conciliates high sustainability and economic interest, since solketal contributes to the fullfilment of a Circular Economy Model through its use in biodiesel blends. The key to guarantee high efficiency and high sustainability for solketal production is the use of a recovery and recyclable heterogeneous catalyst. Some examples are already reported in the literature (first example in 2012), and this review intends to conciliate the information spreaded in this topic and established the most important reacional parameters and the main catalytic characteristics strategies to achieve high solketal production in short reaction time.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

This study concerns the transport and retention of polydisperse micron-sized (16 ± 6 µm) of microplastics (MPls) in porous media under varying flow rate conditions. Sorption kinetics were modeled using first-order reversible and irreversible kinetic sorption models, with sensitivity analyses providing insights into each sorption parameter's effect. Both numerical modeling and experimental measurements were employed to assess sand filter retention rates. The impact of flow rate on sorption reveals variations in distribution coefficient (Kd), mass transfer coefficient (β), and irreversible sorption rate (K1). Lower flow rates are correlated with higher Kd and β values, indicating an increase in sorption and diminished mass transfer rates. The findings revealed that an increase in Kd resulted in a more gradual sorption process with a decrease in peak concentration, whereas changes in β influenced the rate of sorption and peak concentration to a lesser extent compared to Kd. Lower K1 values are associated with higher peak concentrations and decreased retention efficiency. Retention rates were evaluated by a numerical model and found as 28 ± 1% at a flow rate of 31 ml min⁻¹ and 17 ± 1% at 65 ml min⁻¹. The introduction of MPls into soil environments has been noted to modify transport dynamics into soil. As a result, these alterations effects hydrological characteristics of soil, thereby impacting quality of groundwater and agricultural output. The mean absolute error (MAE) of 6% between modeled and observed retention rates suggests minor discrepancies. This study highlights the importance of examining retention efficiency and the accuracy of numerical models in porous media during MPl transport.

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

A solid structure, such as a road, building wall or envelop, used as a solar collector is considered an effective and new way to use renewable energy. This paper focused on the temperature characteristics of four structures exposed to sunshine: asphalt, red brick, composite cement and concrete road slab. Furthermore, the collected heat based on a hydraulic system was investigated experimentally. For the four structure slabs, their temperature differences are due to solar radiation absorption varied greatly by the material’s heat absorptance and color. Through the test, asphalt slab attained the highest temperature and had the weakest reflection among the structures. Compared with the others, the temperature of the asphalt slab was greater by 8.1%, 14.9% and 16.4% than the brick, composite cement and concrete, respectively. The reflection intensity growth ratio was defined and indicates the growth potential for absorbing radiation in the solid slab surface. From the experiments, it was concluded that a suitable selection of road materials can greatly improve the thermal absorption, conduction and penetration into the solid slab. The collected heat capability was approximately 250 W/m2 to 350 W/m2 in the natural summer condition. A black coating or a surface modification can collect more heat, reaching greater than 250 W/m2. The solar collecting heat efficiency with a surface configuration of the road slab can reach above 30% in the summer time.

Seventy-two clavarioid specimens from Johannes Rick's collection at PACA and BPI were revised. Eleven taxa are presented. Illustrations of the microstructures are provided for nine taxa. The description of Scytinopogon robustus includes information from recently collected specimens and SEM photographs of the basidiospores. A new combination, Clavulina ridleyi, is proposed.

Scale inhibitors are deployed as preventive and rejuvenation operation in oil and gas industry when production operations are under threat or menace of scale blockage. The application of scale inhibitors is carried out through a method known as squeezing. In general, the squeeze process is governed by inhibitor-rock interaction which is described by adsorption/desorption isotherm. Most reservoirs produce loose sand grains or fine sand which float and flow within the pore spaces along with the squeezed scale inhibitors. Hypothetical reports have shown that not all scale inhibitors pumped into the formation adsorb onto the formation rock. A number of factors (irreversible adsorption, pH changes, competing ions, concentration and temperature) have been considered to affect the adsorption and return profile of these scale inhibitors. This review work examines the performances of most common scale inhibitors used in the oil and gas production activities, theoretical application in reservoirs and how loose fine sand grains affect the adsorption and desorption characteristics of squeezed scale inhibitors. Additionally, presented were overviews of previous reports on fine sand production and migration of fine sands through formation pores in reservoirs.

Background. Inferior quality of biological material compromises data, slows discovery, and wastes research funds. The gut microbiome plays a critical role in human health and disease, yet little attention has been given to optimizing collection and processing methods of human stool. Methods. We collected the entire bowel movement from 2 healthy volunteers: one to examine stool sample heterogeneity and one to test stool sample handling parameters. Sequencing and bi-oinformatic analyses were used to examine the microbiome composition. Results. The microbiome profile varied depending on where the subsample was obtained from the stool. The exterior cortex of the stool was rich in specific phyla and deficient in others while the interior core of the stool revealed opposite microbiome profiles. Sample processing also re-sulted in varying microbiome profiles. Homogenization and stabilization at 4°C gave superior microbial diversity profiles compared to the fresh or frozen subsamples of the same stool sample. Bacterial proliferation continued in the fresh subsample when processed at ambient temperature. Bacteroidetes proliferated and Firmicutes diminished during the 30-minute processing of fresh sample. The frozen sample had good overall diversity but Proteobacteria diminished likely be-cause of the freeze/thaw. Conclusions. The microbiome profile is specific to the section of the stool being sampled. Stool sample collection, homogenization, and stabilization at 4°C for 24 hours provides a “neat”, high-quality sample of sufficient quantity that can be banked into aliquots with nearly identical microbial diversity profiles. This collection pipeline is essential to accelerate our understanding of the gut microbiome in health and disease.

Effective oral care is important to maintain a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using bioelectric effect (BE) with those of mechanical electric toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

Rhodes grass (Chloris gayana Kunth) is one of the most important forage grasses used throughout the tropical and subtropical regions of the world. Enhancing the conservation and use of genetic resources requires the development of knowledge and understanding about the existing global diversity of the species. In this study, 104 Rhodes grass accessions, held in trust in the ILRI forage genebank, were characterized using DArTSeq markers to evaluate the genetic diversity and population structure, and to develop representative subsets, of the collection. The genotyping produced 193,988 SNP and 142,522 SilicoDArT markers with an average polymorphic information content of 0.18 and 0.26, respectively. Hierarchical clustering using selected informative markers showed the presence of two and three main clusters using SNP and SilicoDArT markers, respectively, with a cophenetic correction coefficient of 82 %. Bayesian population structure analysis also showed the presence of two main subpopulations using both marker types indicating the existence of significant genetic variation in the collection. A representative subset, containing 21 accessions from diverse origins, was developed using the SNP markers. In general, the results revealed substantial genetic diversity in the Rhodes grass collection and the generated molecular information, together with the developed subset, should help enhance the management, use and improvement of Rhodes grass germplasm in the future.

Faba bean (Vicia faba L.) is one of the popular pulse crops grown for traditional consumption, not only in Oman but also in Arabian Peninsula and other countries. In Oman, the famers living in and around high altitude mountain areas mostly grow it. This paper highlights features of variation in seed color and diversity in seed traits found in collected accessions from the joint collecting missions of 2008-2010 between the staff of College of Agriculture, Sultan Qaboos University and the Ministry of Agriculture & Fisheries throughout all the governorates of the Sultanate of Oman. 41 seed samples/accessions were collected from 38 sites. Of these, the highest number of accessions was collected from Batinah South governorate (38) represented mostly by the mountains of Rustaq, followed by the mountains of Interior/Al-Dakhliyah (8), and Dhahira & Buraimi (4). Only one accession was collected from mountains of the Eastern/ Al-Sharqiyah governorates. The seed accessions were found diverse with respect to all seed characters studied, i.e. seed length (cm) and width (cm) and 1000-seed weight (g) besides seed color. The faba bean accessions were classified into 9 genetically diverse clusters based on the Principal Component Analysis, which indicated that the contribution of seed width and 100-seed weight to the total variation existing in indigenous germplasm collected from all the governorates of Oman. It was found from the critical analysis of seed colors that 38 accessions were homogenous (pure) with one color and three were heterogeneous with combinations of colors.

This paper presents the experimental and numerical studies of the vertical stress distribution beneath the centerline of circular footings resting on the sand. Vertical stress values due to circular load in medium-dense sand were measured using soil stress transducers. Reduced-scale laboratory model tests were carried out in a square-shaped test box and vertical stresses were measured at the centerline of the circular footing at different depths of the sand. In order to determine the effect of footing width on vertical stress distribution, laboratory experiments were performed on circular footings of different diameters. In addition, a series of finite element analyses was carried out on the test model to validate the findings of the experimental study. In the numerical analysis, the sand was modeled as a non-linear elastoplastic material. The analyses were performed using the finite element method with two-dimensional axisymmetric and three-dimensional conditions. The results obtained from laboratory model tests and numerical analysis were compared with the vertical stress values obtained from the theoretical solution in the literature. Vertical stress distribution in horizontal planes at any depth from the footing base shows the same characteristic form in all methods. However, some differences were observed between experimental, numerical, and theoretical results and discussed.

Calcareous sand deposits are widely distributed along the shoreline in ropical and subtropical regions. Microbially induced calcite precipitation treatment (MICP) is a relatively new method to improve the stiffness and strength of the soil. Little is known about the small-strain shear modulus and damping ratio of MICP-treated calcareous sand, which are two crucial parameters for the prediction of the dynamic behavior of soil. A series of resonant column tests are performed to investigate the dynamic performance of MICP-treated calcareous sand, with special attention paid to the influence of treatment duration and confining stress on the stiffness and damping characteristics. The relationship between the initial dynamic shear modulus and unconfined compressive strength is analyzed. Additionally, the empirical equations of the reference shear strain between treatment duration and confining stress are given. The G/G0 of MICP-cemented calcareous sand presents a higher strain sensitivity than that of untreated sand, and its attenuation pattern can be described by Hardin-Drnevich model. The σc has an apparent effect on the degradation characteristics of the dynamic shear modulus of MICP-treated calcareous sand with a low cementation level, however, its effect decreases with the increasing treatment duration. The relationship between the reference shear strain and the treatment duration and confining stress can be described by a power and a linear formula, respectively.

The adoption of recycling and proper disposal techniques for electronic waste is crucial in advancing sustainable development. The traditional approaches of motivating people for collection of electronic waste are often insufficient due to inadequate methods reaching out, given incentives, calculating appropriate incentives associate to the task of gathering the electronic waste and a lack of transparency in the entire process. Insufficient collection of electronic waste could result in the release of numerous harmful substances into the environment. Prior research studies have been carried out to tackle the issue of electronic waste management in a broad sense. The findings of those studies indicated diverse strategies, each of which is relevant solely to a restricted range of electronic waste reprocessing circumstances. The current study has presented a proposed technique for incentivizing tasks and activities associated to collection of electronic waste through the adoption of vector space technique. Blockchain smart contact technology, has been used to implemented the strategy. The method used involves various well defined mapping of tasks, nature of activities, and their magnitude in order to derived an incentive. Some scenarios for the calculations of incentives are presented, and the findings reveals the based case is by utilizing weighting scale scheme where each tasks and activities are mapped to its associated inventive rather than providing fixed incentive values. Ethereum was used as digital token for each unit of incentive. This concept has contributed in encouraging personal accountability in the management of e-waste collection in order to cultivate sustainable behaviors for a long term solution.

The newly discovered coronavirus (COVID-19) has disrupted traditional methods of conducting research, particularly qualitative research. However, there remains a number of methods by which qualitative data can still be collected. These include the use of digital voice, video, and text-based tools, online surveys, and content analysis. Text-based sources can help to overcome the limitations of time and space, and also can be cost-effective. This chapter draws from data collected from 12 participants across Zimbabwe and demonstrates how these tools can be used to generate data or to sample data that is already available to satisfy research questions and meet research objectives. It recommends researchers to experiment with new ways of collecting qualitative data while also observing safety protocols and ethical considerations.

Large amounts of pumice stone generated by the submarine volcanic eruption at Fukutoku Okanoba on August 13, 2021, drifted ashore, affecting ship navigation and fishery operations. Through laboratory experiments, we investigated the possibility of using pumice as a sand-capping material for eutrophic sediments. Crushed pumice as a sand cover material effectively reduced the sedimentary oxygen consumption rate. Nutrient release from sediment showed a similar trend, with ~25% and 82% reduction in NH4-N and PO4-P release rates, respectively. Furthermore, the bivalve exposure experiments using crushed pumice suspended in seawater showed no adverse effects specific to pumice and lower bivalve mortality than that using kaolin at the same concentration. This could be owing to differences in gill accumulation and blockage owing to the particle size variation of the suspended particles. These results suggest that crushed pumice is effective for sand covering and suppresses oxygen consumption and nutrient release from the sediments.

Beach sand may act as a reservoir for numerous micro-organisms, including enteric pathogens. Several of these pathogens originate in human or animal feces, which may pose a public health risk. In August 2019, high levels of fecal indicator bacteria (FIB) were detected in the sand of the Azorean beach Prainha, Terceira Island, Portugal. Remediation measures were promptly implemented, including sand removal and the spraying of chlorine to restore the beach sand quality. To determine the biological source of the contamination, during the first campaign, supratidal sand samples were collected from several sites along the beach, followed by microbial source tracking (MST) analyses of Bacteroides markers for five animal species, including humans. Some of the sampling sites revealed the presence of marker genes from dogs, seagulls, and ruminants. Making use of the information on biological sources originating partially from dogs, the municipality enforced restrictive measures for dog-walking at the beach. Subsequent sampling campaigns detected low FIB contamination due to the mitigation and remediation measures that were undertaken, thereby no longer requiring MST marker-gene analysis. This is the first case study where the MST approach was used to determine the contamination sources in the supratidal sand of a coastal beach. Our results show that MST can be an essential approach to determine sources of fecal contamination in the sand. This study shows the importance of holistic management of beaches that should go beyond water quality monitoring for FIB, putting forth evidence for the need for sands also to be monitored.

Raw materials used for producing concrete, such as sand and gravel, are in short supply worldwide. It has been reported that the production of cement, one of the main constituents of concrete, results in the emission of a large amount of CO₂, accounting for 8% of total global CO₂ emissions. In this study, we developed a method to produce a construction material using only sand as the solid raw material. By utilizing a technique to produce organic silicon material from sand, we placed sand, alcohol, and catalyst in a closed vessel and heated it to 240 °C. After 24 h, the sand particles were bonded to each other, and a hardened body was formed. A tradeoff in production conditions, such as temperature, time, and the amount of sand, was confirmed.

Continuous research into the availability of phosphorus (P) in forest soil is critical for sustainable management of forest ecosystems. In this study, we used sequential chemical extraction and 31P-nuclear magnetic resonance spectroscopy (31P-NMR) to evaluate the form and distribution of inorganic P (Pi) and organic P (Po) in Casuarina forest soils of a subtropical coastal sand dune at Houlong in Taiwan. The soil samples were collected from humic (+2-0 cm) and mineral layers (mineral-I: 0-10, mineral-II: 10-20 cm) at two topographic locations (upland and lowland) by elevation. Sequential chemical extraction revealed that the NaOH-Po fraction, as moderately recalcitrant P, was the dominant form in humic and mineral-I layers in both upland and lowland soils, whereas the cHCl-Pi fraction was the dominant form in the mineral-II layer. Resistant P content, including NaOH-Pi, HCl-Pi, cHCl-Pi, and cHCl-Po fractions, was higher in the upland than lowland in the corresponding layers; however, labile P content, NaHCO3-Po, showed the opposite pattern. Content of resistant Pi (NaOH-Pi, HCl-Pi, and cHCl-Pi) increased significantly with depth, but that of labile Pi (resin-Pi and NaHCO3-Pi) and recalcitrant Po (NaHCO3-Po, NaOH-Po, and cHCl-Po) decreased significantly with depth at both locations. 31P-NMR spectroscopy revealed inorganic orthophosphate and monoesters-P as the major forms in this area. The proportions of Pi and Po evaluated by sequential chemical extraction and 31P-NMR spectroscopy were basically consistent. The results indicated that the soils were in weathered conditions. Furthermore, the P distribution and forms significantly differed between the upland and lowland by variation in elevation and eolian aggradation effects in this coastal sand dune landscape.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

Drinking water, in addition to the best-known chemical and biological agents, contains radionuclides of both natural and artificial origin, which can contribute significantly to the overall effective dose received by the population. The Italian Decree Law 28/2016, implementing 2013/51/EURATOM Directive, establishes the activities for risk management and the parameter values for different radionuclides activity concentrations. In addition to the institutions involved, annually the National Inspectorate for Nuclear Safety and Radiation Protection (ISIN), publishes the monitoring reports of environmental radioactivity in Italy, including radioactivity in drinking water. The purpose of the study was to integrate ISIN reports with 2018 to 2020 data by collecting measurements performed by institutional laboratories to obtain a more complete information and adding, for the Campania region, some data not yet published. This new updated report was not significantly different from ISIN’s one, meaning that those publications are nevertheless extremely representative of the radioactivity in Italian drinking water. However, the study allowed to obtain a more detailed data also including measurements not considered in ISIN reports, for instance, radon-222 activity concentrations. This may be of great usefulness for all radiation protection stakeholders in order to ensure environmental protection, pollution prevention and the population safety.

A macro network loading Model for multi-flow lines, time-varying and pedestrian congestion is proposed. The station hub is abstracted as a network of different types of nodes, and the flow of passengers at each node is calculated in real time for the purpose of simulating the hub's collection and distribution process. For correct transmission of passenger flow on heterogeneous networks, three types of indexes are proposed to distinguish the nodes, and then match the corresponding fundamental diagrams. This paper divides the update process of the dynamic network loading model into multiple processes by flow lines, and improves computational speed of DNL model. The proposed model is applied to the simulation of passenger flow collection and distribution in an actual hub station with multi-flow lines. The analysis results illustrate that the model can accurately reflect the realistic congestion facilities and explain the formation process of high-density areas. A rolling passenger flow control model based on optimal control theory is proposed. The effectiveness of the control model is verified based on simulation data.

Recently, inter-vehicle communication, which helps to avoid collision accidents (by driving safety support system) and facilitate self-driving (by dissemination of road and traffic information), has attracted much attention. In this paper, in order to efficiently collect road / traffic information in the request / response manner, first a basic method, Content-centric network (CCN) for Vehicular network (CV), is proposed, which applies CCN cache function to inter-vehicle communication. Content naming and routing, which take vehicle mobility into account, are investigated. On this basis, the CV method is extended (named as ECV) to avoid the cache miss problem caused by vehicle movement, and is further enhanced (named as ECV+) to more efficiently exploit cache buffer in vehicles, caching content according to a probability decided by channel usage rate. Extensive evaluations on network simulator Scenargie, with realistic open street map, confirm that the CV method and its extensions (ECV, ECV+) effectively reduce the average number of hops of data packets (by up to 47%, 63%, 83% respectively) and greatly improve the content acquisition success rate (by up to 356%, 444%, 689%, respectively), compared to the method without cache mechanism.

Anthropogenic development can strongly influence natural river processes, leading to environmental changes that negatively affect important habitats and biodiversity, and consequently reduce economically important natural resources. This study investigated the effects of salinity intrusion on the habitat of the clam Corbicula japonica in the Seomjin River estuarine zone. We employed the Environmental Fluid Dynamics Code (EFDC) model, which incorporates topographic data and hydrological changes, to simulate salinity concentrations. Two salinity measurement facilities were installed in Seomjin River estuarine and operated to optimize the EFDC model. The results show that reduced flow rates due to intake have a negligible impact on the increased salinity. Maintaining optimal salinity (15–20 psu) during neap tides at the Seomjin River Bridge requires constant high flow rates, which poses significant challenges. Saltwater stratification is identified as the primary cause of pronounced salinity stratification, particularly during neap tides. Addressing this issue through river discharge and intake facility operation is challenging. Structural measures, including riverbed restoration and underwater barriers, are recommended to improve resistance to seawater intrusion. Future research should aim to develop scenarios to reduce salinity concentrations, quantify the reduction efficiency, and propose region-specific measures.

Aging kills 100,000 people a day - more than any other cause of death combined. The exact causes of aging have been much discussed, but the most pressing issue with regard to aging appears to me to be lipofuscin accumulation. That is, the accumulation of indigestible cellular garbage that needs to be removed from our cells, then the body. In this piece, I will explain why I think “getting rid of the garbage” should be at least one of our main goals with regard to longevity research for now.

Numerous protocols have been published for extracting DNA from phlebotomines. Nevertheless, their small size is generally an issue in terms of yield, efficiency, and purity, for large-scale individual sand fly DNA extractions when using traditional methods. Even though this can be circumvented with commercial kits, these are generally cost-prohibitive for developing countries. We encountered these limitations when analysing parasite infection in Lutzomyia spp. by PCR [1] and, for this reason, we evaluated various modifications on a previously published protocol ([2] and Acardi personal communication). The most significant variation was the use of a different lysis buffer [3] to which added Ca2+ (buffer TESCa), because this ion protects proteinase K against autolysis, increases its thermal stability, and could have a regulatory function for its substrate-binding site [4]. Individual sand fly DNA extraction success was confirmed by amplification reactions using internal control primers that amplify a fragment of the cacophony gene [5,6]. To the best of our knowledge, this is the first time a lysis buffer containing Ca2+ has been reported for the extraction of DNA from sand flies.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

Standardized protocols were specifically designed and developed for clinical information collection and obtaining trio genomic information from infants affected with congenital anomalies (CA) and their parents, as well as securing human biological resources. Two large areas of these protocols include clinical and genomic information collection on CA which were difficult to diagnose using pre-existing screening methods. The following are three essential items for the clinical information collection protocol: establishment of a consent system for collecting and utilizing research resources, establishment of criteria for target patient selection, and collection of clinical and epidemiological information. A total of 138 cases consisting of 45 families of infants with CA and their parent trios have provided human-derived resources and genomic information. Whole genome sequencing data have been generated for all participants, and standardized protocols for resource collection and manufacturing have been developed. Phenotype information according to the Human Phenotype Ontology term and major test findings were recorded. It is important to keep updating and recording clinical symptoms and genetic diagnosis that are newly added or changed over time. The unique significance of this study is to develop a protocol that enables long-term tracking by adding growth and development tests that reflect important characteristics of newborns. By using these clinical and genetic information collection protocols for CA, it will be possible to establish an essential platform for early genetic diagnosis and diagnostic research, and further present new genetic diagnostic guidelines in the near future.

Mast cells (MCs) play a crucial role during infections with Leishmania, that is transmitted through the bite of an infected sand fly that injects saliva together with the parasite. Sand fly saliva is a complex fluid that modulates the host immune response. In addition, hormonal factors modulate the host immune response, impacting the susceptibility to infections. Thus, to assess the impact of androgens and salivary proteins of sand fly vectors on the mast cell (MC) response to Leishmania infections, we infected orchiectomized male mice with the parasite in the presence or absence of sand fly salivary proteins and analyzed the inflammatory response of MCs. Our results showed a differential MC response to the parasite and to vector salivary proteins in mice deprived of gonadal hormones, as compared to sham-operated mice. Orchidectomy induced a different pattern of activation in MC of animals infected with Leishmania and vector-salivary proteins. Our results show that during Leishmania infection, androgens modulate the innate immunity response against the parasite and salivary proteins of the sand fly vector.

Information Technology (IT) has become an essential part of our lives and due to the emergence of Internet-of-Things (IoT), technology has encompassed a majority of things that humans rely on in their daily lives. Further, as IT becomes more relevant in daily lives, the need for IT to serve public emergency services has become more important. However, due to the infancy status of IoT, there is a need for a data consortium that would prove to be best used in servicing policing in a technological driven society. This paper will discuss the plausibility of creating a universal format for use in carrying out public services, such as emergency response by the police and regular law maintenance. In this research we will discuss what the police requires in their line-of-duty and how smart devices can be used to satisfy those needs. A data formatting framework is developed and demonstrated, with the goal of showing what can be done to unifying data from smart city sensors.

The Combined Elevation Test (CET) is a musculoskeletal screening technique (MST) replicates the streamline position in swimming and is commonly used in various sports. Although the CET is widely used, no normative data exist within an adolescent population. Therefore, the purpose of this study was to develop a normative data set for the CET within an adolescent population and to evaluate the influence various demographic and anthropometric variables. Data was collected for 416 participants aged between 8 and 18 years old. Age and arm span showed a significant correlation with CET scores (arm span r_s (105) = .478, p = .000, age r_s (416) = .238 p = .000). Regression analysis further quantified the influence of arm span and age on CET scores accounting for 23.1% and 5.3% of variability respectively. These results can be used as a reference point for clinicians and coaches who are using the CET within their assessment.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

In this work, we report the electric energy storage properties of (1-x)Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics enhanced via a domain engineering method. A rhombohedral–tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x=0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie Weiss law (γ=1.83). The rhombohedral–tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

DBP and DEHP are two of the most common plasticisers used in modern industries, which have aroused a major concern over their ubiquitous occurrence and hazardous environmental effects. This study presents the first data of phthalates’ occurrence and distribution in the Maltese shoreline sand. DBP and DEHP occurrences’ was investigated in three busy and secluded beaches, respectively. Analytical determination involved quantifying DBP and DEHP from 75 samples using UPLC-MS/MS through triple repeatability. The concentrations ranged between 0.0095–0.07034 µg/g and <LOQ–0.0977 µg/g for DBP and DEHP, respectively. Statistical analysis of the comparison of phthalates in different beaches demonstrated that the occurrence of DBP and DEHP in Maltese shoreline sand varies. The differences in the occurrence of phthalates were attributed to the beaches’ topography and anthropogenic pressures. Analysis of the effects of anthropogenic activities on the occurrence of phthalates showed a positive association. Distribution analysis showed that DBP and DEHP exhibit an uneven distribution along the shoreline. Conversely, different distributions were observed at distances away from the sea. The uneven distributions observed were associated with anthropogenic activities, different chemodynamic properties and wave action. Cluster analysis was performed to prove the interactions between the phthalates’ concentrations and the characteristics of the beaches.

One of the most extensively studied topics in dozens of studies is the alteration process of ilmenite, the formation of leucoxene and the presence of some impurity oxides; SiO2 and Al2O3. The altered Egyptian black sand ilmenite grains of relatively lower magnetic characters are studied using the binocular microscope and the Cameca SX-100 microprobe instrument. Both of individual brown and black altered grains separated at 0.5 and 1 ampere values are investigated. The detection of the Various alteration phases, the mechanism of formation, their molecular formulas & limits, and the role of SiO2&Al2O3 in alteration mechanisms are detected. The alteration phases includes: pseudorutile (psr) and leached pseudorutile (lpsr) of different phases in addition also to rutile. Few analyzed spots are detected to be leached ilmenite (lilm). Several Excel softwares are adopted to calculate the chemical formulas of each alteration phase. The contents of TiO2 and Fe2O3 of all the investigated psr-lpsr in the study range between 59.16-86.56%, and 37.3-6.68%, respectively. The Ti/(Ti+Fe) ratio for these formulas ranges between 0.60 and 0.88. The psr-lpsr chemical formulas of all the investigated grains range as follows: Fe2.01-0.50Ti3O8.97-4.50(OH)0.03-4.50 . The concluded lowest cationic iron content of the well defined accepted lpsr phase is 0.5 with a corresponding molecular formula of Fe0.50Ti3O4.5(OH)4.5. It was concluded that in the region of 68-70 TiO2%, the mechanism of ilmenite alteration may be changed where neither all the analyzed TiO2 of the spot nor all the calculated structural water are contained within the molecular formula of lpsr. There are other associated mineral phases containing for some TiO2 and also some structural water which most probably are removed from the lpsr phase. As the analyzed spots are located at highly fissured locations, as the alteration process is relatively faster and the lpsr phase can be broken into rutile and hematite. Also, as the analyzed TiO2 and structural and/or molecular water contents increase, as the darkness of the BSE image areas of the grain increases; this may reflect the existence of an individual TiO2 phase; most probably rutile, mixed in homogeneity with the existed lpsr component. As the content of TiO2 increases; within a definite TiO2 range (80-85%), as the associated contents of Al2O3&SiO2 increase. When the contents of the structural and/or molecular water contained within the lpsr phases decreases; the sum total oxides is more than 98%, the contents of Al2O3 are highly depleted. In the late alteration stages, the lpsr structure does not suddenly collapse but gradually producuing other associated mineral phases. The relatively enriched contents of SiO2 and/or Al2O3 in some secondary rutile grains can be explained as most of the SiO2% is associated with mol water or bearing for mol and/or str water necessary for the leachability of Fe3+ from the psr structure. The XRD patterns of the investigated grains before and after roasting at 1100 oC for one hour are detected and interpreted.

Autonomous driving vehicles rely on sensors for the robust perception of surroundings. Such vehicles are equipped with multiple perceptive sensors with a high level of redundancy to ensure safety and reliability in any driving condition. However, multi-sensor, such as camera, LiDAR and radar, systems bring up the requirements related to sensor calibration and synchronization, which are the fundamental blocks of any autonomous system. On the other hand, sensor fusion and integration have become important aspects of autonomous driving research and directly determine the efficiency and accuracy of advanced functions such as object detection and path planning. Classical model-based estimation and data-driven models are two mainstream approaches to achieving such integration. Most recent research is shifting to the latter, showing high robustness in real-world applications but requiring large quantities of data to be collected, synchronized, and properly categorized. To generalize the implementation of the multi-sensor perceptive system, we introduce an end-to-end generic sensor dataset collection framework that includes both hardware deploying solutions and sensor fusion algorithms. The framework prototype integrates a diverse set of sensors, such as cameras, LiDAR, and radar. Furthermore, we present a universal toolbox to calibrate and synchronize three types of sensors based on their characteristics. The framework also includes the fusion algorithms, which utilize the merits of three sensors , namely, camera, LiDAR and radar, and fuse their sensory information in a manner that is helpful for object detection and tracking research. The generality of this framework makes it applicable in any robotic or autonomous applications, also suitable for quick and large-scale practical deployment.

Fusarium Head Blight (FHB) is a destructive disease affecting the grain yield and quality of wheat, barley, rye and triticale. Developing varieties with genetic resistance is integral to successfully managing FHB. However, significant knowledge gap exists in the genetic diversity present in triticale for FHB resistance. This information is critical for breeding new varieties of triticale as its production continues to increase. In the present study, a set of 298 winter triticale accessions from a worldwide collection were screened for their type-2 FHB resistance in an artificially inoculated misted nursery with high levels of inoculum density. Most of the triticale accessions were susceptible to FHB, and only 8% of accessions showed resistance in the field nursery screening. The resistant accessions identified in the nursery screening were selected and further screened for three years in greenhouse conditions. Seven accessions were found to show robust FHB resistance over the three years of greenhouse testing. Thirteen accessions showed significantly lower levels of Deoxynivalenol accumulation when compared to the susceptible triticale control. The accessions identified in the study will be useful in triticale and wheat breeding programs for enhancing FHB resistance and reducing DON accumulation.

General Variable Neighborhood Search (GVNS) is a well known and widely used metaheuristic for efficiently solving many NP-hard combinatorial optimization problems. Quantum General Variable Neighborhood Search (qGVNS) is a novel, quantum inspired extension of the conventional GVNS. Its quantum nature derives from the fact that it takes advantage and incorporates tools and techniques from the field of quantum computation. Travelling Salesman Problem (TSP) is a well known NP-Hard problem which has broadly been used for modelling many real life routing cases. As a consequence, TSP can be used as a basis for modelling and finding routes for Geographical Systems (GPS). In this paper, we examine the potential use of this method for the GPS system of garbage trucks. Specifically, we provide a thorough presentation of our method accompanied with extensive computational results. The experimental data accumulated on a plethora of symmetric TSP instances (symmetric in order to faithfully simulate GPS problems), which are shown in a series of figures and tables, allow us to conclude that the novel qGVNS algorithm can provide an efficient solution for this type of geographical problems.

Business Intelligence, defined by [1] as "the ability to understand the interrelations of the facts that are presented in such a way that it can guide the action towards achieving a desired goal", has been used since 1958 for the transformation of data into information, and of information into knowledge, to be used when making decisions in a business environment. But, what would happen if we took the same principles of business intelligence and applied them to the academic environment? The answer would be the creation of Academic Analytics, a term defined by [2] as the process of evaluating and analyzing organizational information from university systems for reporting and making decisions, whose characteristics allow it to be used more and more in institutions, since the information they accumulate about their students and teachers gathers data such as academic performance, student success, persistence, and retention [5]. Academic Analytics enables an analysis of data that is very important for making decisions in the educational institutional environment, aggregating valuable information in the academic research activity and providing easy to use business intelligence tools. This article shows a proposal for creating an information system based on Academic Analytics, using ASP.Net technology and trusting storage in the database engine Microsoft SQL Server, designing a model that is supported by Academic Analytics for the collection and analysis of data from the information systems of educational institutions. The idea that was conceived proposes a system that is capable of displaying statistics on the historical data of students and teachers taken over academic periods, without having direct access to institutional databases, with the purpose of gathering the information that the director, the teacher, and finally the student need for making decisions. The model was validated with information taken from students and teachers during the last five years, and the export format of the data was pdf, csv, and xls files. The findings allow us to state that it is extremely important to analyze the data that is in the information systems of the educational institutions for making decisions. After the validation of the model, it was established that it is a must for students to know the reports of their academic performance in order to carry out a process of self-evaluation, as well as for teachers to be able to see the results of the data obtained in order to carry out processes of self-evaluation, and adaptation of content and dynamics in the classrooms, and finally for the head of the program to make decisions.

Heavy metals are non-biodegradable and have a high toxicity effect to living things which makes their presence in the environment extremely dangerous. The method of handling heavy metals waste by photocatalysis techniques using TiO2/SiO2 composite showed a good performance in reducing harmful pollutants. In this study, SiO2 from Bengkulu beach sand was used as a support material for TiO2 photocatalyst to reduce Cr(VI) and Pb(II) concentrations. SiO2 was obtained through leaching techniques using NaOH as a solvent. The TiO2/SiO2 composite photocatalyst were synthesized using a solvothermal method at 130 °C and then characterized using XRD, FTIR, SEM and PSA. Based on the XRD diffractogram, the synthesized TiO2 showed the anatase structure while the SiO2 showed the amorphous structure. Ti-O-Si bond is defined in the IR spectra, which indicates that the relationship between TiO2 and SiO2 is a chemical interaction. The results of SEM and PSA characterizations show agglomerated spherical (round) particles with a mean particle size of 616.9 nm. The TiO2/SiO2 composite of 7:1 ratio showed the highest photocatalytic activity after 180 minutes of UV irradiation, with a concentration-decrease percentage of 93.77% and 93.55% for for Cr(VI) and Pb(II), respectively.

There is significant need for development of a new environmentally friendly, extraction-free sample collection medium that can effectively preserve and protect genetic material for point-of-care, and/or self-collection, home-collection, and mail-back testing. Systematic Evolution of Ligands by Exponential Enrichment (SELEX) was used to create anti-ribonuclease (RNase) Deoxyribonucleic acid (DNA) aptamers against purified RNase A conjugated to paramagnetic carboxylated beads. Following 8 rounds of SELEX carried out under various stringency conditions, e.g., selection using Xtract-Free™ (XF) specimen collection medium, and elevated ambient temperature of 28 ºC, a panel of 5 aptamers was chosen following bioinformatic analysis using next-generation sequencing. The efficacy of aptamer inactivation of RNase was assessed by monitoring Ribonucleic acid (RNA) integrity by fluorometric and real-time RT-PCR analysis. Inclusion of aptamers in reaction incubations resulted in an 8,800 to 11,200-fold reduction of RNase activity, i.e., digestion of viral RNA compared to control. Thus, anti-RNase aptamers integrated into XF collection medium as well as other commercial reagents and kits have great potential for ensuring quality intact RNA for subsequent genomic analysis.

Background: Retinal diseases such as neovascular age related macular degeneration (nAMD), diabetic macular edema (DME) or branch-/central retinal vein occlusion (B/CRVO) have significant implications for patients' social and psychological well-being. To gain a comprehensive understanding of patients' backgrounds and attitudes, we developed an exploratory questionnaire, the Basic Care and Patient Satisfaction Questionnaire (BPZ-9). Methods: The ALBATROS study aimed to assess the care situation of treatment-naïve patients diagnosed with either nAMD, DME or B/CRVO. The data collection took place at the beginning of treatment and after twelve months of anti-VEGF (vascular endothelial growth factor) therapy. The BPZ-9 instrument comprises nine questions to evaluate patients’ psychological and social situation and their satisfaction with treatment. Results: Data were collected from 1.478 nAMD (mean 78 years), 445 DME (67 years), 233 BRVO (70 years) and 144 CRVO (71 years) patients at 102 study centers throughout Germany. Approximately one third of the patients was living alone and six percent were in organized care. One in four patients had difficulties to walk and one in five needed accompany for treatment. Anxiety to lose vision was present in three out of four patients at the beginning and slightly decreased to two out of three over the 12-month treatment preriod. The distress of having a retinal disease was generally higher than the distress related to treatment. Most patients reported high treatment satisfaction (73%) and felt well informed (81%). Conclusion: Patients receiving anti-VEGF therapy commonly experience impaired mobility, dependency on others, distress and the fear of vision loss.

Energy consumption modelling is of critical importance for improving energy efficiency in the drive towards sustainable manufacturing. Modern manufacturing processes and machine tools are very complex as they involve interplay of several advanced technologies. Therefore, energy modelling of modern machine tools is a complex multi-disciplinary task. This paper proposes a systematic and practical framework to choose the appropriate modelling approach for a given industrial problem. The framework was validated by applying it to diverse industrial scenarios.

In the process of sewage coagulation treatment, quartz sand is often used as a heavy medium to accelerate the settling rate of flocs, but it will adversely affect the removal efficiency of pollutants. The factors that affect the coagulation effect and can be controlled manually include the quartz sand dosage, coagulant dosage, sewage pH, stirring time, settling time, etc, their reasonable setting is critical to. This paper was to study the optimal conditions of quartz sand enhanced coagulation(QSEC), first, single-factor tests were conducted to preliminarily explore the optimal range of influencing factors, and then response surface methodology（RSM）tests were performed to accurately determine the optimums of significant factors. The results showed that the addition of quartz sand can’t improve the water quality of coagulation treatment, but it can significantly accelerate the coagulation settlement process, the quartz sand dosage, the coagulant dosage and sewage pH all impacted significantly on its coagulation effect, and existed inflection points. A model that could guide QSEC was obtained by RSM tests. The model optimization and experimental validation showed that the optimal QSEC conditions for treating domestic sewage were as follows: the polyaluminum chloride(PAC) dosage, cationic polyacrylamide(CPAM) dosage, the sewage pH, quartz sand dosage, stirring time and settling time were 0.97 g·L-1, 2.25 mg·L-1, 7.22, 2 g·L-1, 5 minutes and 30 minutes, respectively, and the turbidity of treated sewage was reduced to 1.15 NTU.

In this paper, the main characteristics of the natural bitumen of the Munaily-Mola oil sands were studied with comparison crude oil of Karazhanbas oil field. During the experiment, the density, heating value, ash content and elemental composition of natural bitumen were determined, and these parameters were compared with the properties of Karazhanbas crude oil. As well as oil, resin and asphaltene fractions of both hydrocarbons were separated and each of them were analyzed at a Fourier transform IR-spectroscopy Spectrum-65 with 450-4000 cm−1 range. According to these indicators, it is concluded that natural bitumen is a heavy hydrocarbon raw material with highly resin-asphaltene compounds. Like Karazhanbas oil, natural bitumen can be used as a raw material for various petrochemical products. By finding ways of effective processing of natural bitumen, it can be used in useful areas of the national economy.

Due to limitation of natural sand from rivers and seas, artificial sand production from large stones or rocks is being increased. However, this sand manufacturing process is dangerous and causes several social problems such as high level of unwanted vibrations or noises. This study investigates vibration characteristics of sand and screen units in artificial sand production plant whose actuating operation is multiple with several different exciting frequencies. As a first step, vibration levels are measured at the sand and screen unit positions using accelerometers in time and frequency domains. The measurement is carried out at two different conditions: activating sand unit only and operating entire facilities such as stone crusher. Vibration signals acquired from several locations of the sand and screen units of the plant are collected and analyzed from waveforms and spectrums of the signals. It is identified that the vibration acceleration level of the screen unit is higher than that of the sand unit. In addition, it is found from the acceleration signals measured at plant office and shipping control center those places are far away from the plant location that the beating phenomenon is occurred by close driving frequencies for several sand units. In this work, the vibration caused from the beating is significantly reduced by adjusting the driving frequencies for the sand units so that they are sufficiently scattered to avoid the beating.

In an attempt to improve the quality of the agricultural drain in Egypt for its reuse again in the irrigation, low cost solution such as sand filter along with/ without other filtration media have been used in this research, As a result of that, pilot plant of sand filter mixed with other filtration media was tested for its ability to improve the sand performance in removing the suspended solids and organic matters from agricultural drain water of the Belbeis drain (in Sharkia governorate in Egypt). Only sand compared with sand with sponge and sand with Liyan Nanfang activated carbon (L.N.A.C) have been tested to find the optimum mixing sand/ medium ratio &optimum infiltration rate. The work has been done on four runs. It was found that sand mixed with sponge gave the best removal efficiency compared to that of the sand only and the sand mixed with L.N.A.C. The results presented that the concentration of CODt, CODsol and TSS was reduced from 125, 47 and 162 mg/l to 44, 34 and 28 mg/l respectively at optimum infiltration rate of 2 m³/m²/d for sand mixed with sponge.

This study addressed the need for efficient data collection in micro-mobility using low-end hardware, focusing on developing a system capable of handling large real-time data streams. We proposed a novel data collection system that leverages incremental learning techniques, enabling AI-based services for micro-mobility passengers through smartphones. Our approach utilizes 3-axis acceleration sensors integrated into micro-mobility devices, collecting motion data in real-time. This data is processed through an incremental learning pre-processing server, employing the Broad Learning System algorithm, to ensure robust performance in noisy, real-world environments. The use of incremental learning is pivotal, allowing our system to adapt continuously to new data, enhancing the accuracy and relevance of the AI services provided to passengers. This research not only advances the technical capabilities in micro-mobility data handling but also has the potential to enhance the overall passenger experience through improved AI-based services.

Municipal Solid Waste Management (MSWM) struggles with significant policy and operational challenges, particularly concerning recyclables collection routes and fleet composition. Within the European Union, phasing out traditional fuel-based vocational vehicles, like garbage trucks, in favor of zero-emission alternatives is mandatory to achieve sustainable development objectives. Integrating electric solid waste collection vehicles into municipal fleets presents challenges due to differences in range, capacity, and noise levels. The emission is even more crucial in the systems where recyclables are collected separately, which requires a greater number of trips to be performed. This study addresses MSWM’s strategic aspect by minimizing the total cost of replacing waste collection vehicles while meeting emission constraints. The Fleet Transition Problem (FTP) was formulated and solved using a MARKAL-based approach. The objective of the FTP and a mixed integer linear program used to solve it is minimizing the overall cost of fleet modernization throughout a multi-phase planning horizon so that the sustainable transition of the fleet can be assured. Computational experiments affirmed the model’s effectiveness in strategizing fleet transition. This research outlines a multi-period model for transitioning to a zero-emission fleet and demonstrates the FTP’s potential for strategic decision-making. Notably, the study observes a consistent reduction in permissible emissions across the planning horizon.

Candida spp. are the most common cause of fungal infections worldwide. The taxonomy of Candida is controversial and has undergone recent changes due to novel genetically related species. Therefore, some complexes of cryptic species have been proposed. In clinical settings, the correct identification of Candida species is relevant since some species are associated with high resistance to antifungal drugs and increased virulence. This study aimed to identify the species of four Candida complexes (C. albicans, C. glabrata, C. parapsilosis, and C. haemulonii) by molecular methods. This is the first report of six cryptic Candida species in Honduras: C. dubliniensis, C. africana, C. duobushaemulonii, C. orthopsilosis, and C. metapsilosis, and it is also the first report of the allele hwp1-2 of C. albicans sensu stricto. It was not possible to demonstrate the existence of C. auris among the isolates of the C. haemulonii complex. We also propose a simple method based on PCR-RFLP for the discrimination of the multi-resistant pathogen C. auris within the C. haemulonii complex.

Plastics play a pivotal role in the principles of a circular economy, where their effective recycling post-utilization, leading to economic value generation and minimal environmental harm, is crucial for achieving sustainable management. Extensive research has delved into the incorporation of waste plastics in concrete, showcasing promising outcomes with a myriad of advantages..The escalating volume of plastic waste is becoming a pressing issue, contributing to environmental pollution, particularly in densely populated cities and towns in Nigeria such as Delta, Aba, Port Harcourt, Onitsha, Enugu, Benue, and Ogun. These urban centers experience high consumption of goods packaged or sealed in plastic materials. Tourist destinations are also affected as large quantities of plastic waste are improperly disposed of or incinerated, resulting in environmental contamination and air pollution. Efforts to address this growing concern are crucial to safeguarding the environment and public health in these regions.Therefore, it is imperative to find effective ways to utilize these waste plastics. By cleaning low-density polyethylene bags and combining them with sand at specific proportions, high-strength bricks can be produced. These bricks not only exhibit thermal and sound insulation properties but also help in pollution control and cost reduction in construction projects. This innovative approach not only addresses the issue of accumulating plastic waste, a non-biodegradable pollutant, but also offers a sustainable solution to manage plastic waste while contributing to the construction industry's efficiency and environmental protection., By incorporating waste plastic and nylon into brick production, we not only reduce the amount of sand extracted from our natural resources like rivers and seas but also utilize the surplus plastic waste that is currently discarded. This research focuses on creating eco-friendly bricks by incorporating molten plastic, nylon, and plastic bottles in varying percentages (0 to 15% by weight) along with 5kg of fly ash. The experimental results from this study will shed light on the feasibility and benefits of using these materials in brick manufacturing, highlighting the potential of sustainable construction practices that minimize environmental impact and resource depletion, The experimental process involved utilizing cement and sand to complete the brick composition, with curing conducted underwater for 29 days followed by baking at temperatures between 100°C to 120°C for 2 hours. The resulting eco-friendly bricks exhibited key characteristics such as being lightweight, porous, having low thermal conductivity, and displaying appreciable mechanical strength. Interestingly, the compressive strengths of these bricks, post the addition of waste plastic and nylon, were found to be comparable to that of conventional bricks. Additionally, these eco-friendly bricks showcased reduced water absorption capacity compared to regular bricks, offering a promising alternative for sustainable and efficient construction practices.The eco-friendly bricks made from A, B, C, and D using 0%, 5%, 10%, and 15% plastic/nylon waste showed comprehensive strengths of 19.5 ,19.46, 20.3, and 21.1 respectively, with corresponding water absorption percentages of 0.34, 0.25, 0.22, 0.20, and 0.085. The efflorescence values were lower than those of normal bricks. These bricks are likely to enhance energy efficiency in buildings and provide economic value to manufacturers, thereby promoting a sustainable ecosystem for plastic waste management with the involvement of all stakeholders.

In the natural environment, sand accumulation and desertification can influence the efficiency of photovoltaic arrays. In this study, PV module output characteristics were examined under different sand particle size, varying sand densities and inclination angles, and at wind speeds of 5m/s, 10m/s, and 15m/s. Both theoretical and experimental results showed that the output power of the module declines with increasing sand density. As the sand particle size increases, the module maximum output power rises and then stabilizes. The two control variables, namely sand density and sand particle size, influence the module temperature and light transmittance distinctly. Contrary to the impact of sand density on the module filling factor curve, the module filling factor exhibits varying trends under different sand particle sizes. Additionally, the pattern of the module filling factor as a function of sand density contrasts with that of the module temperature under analogous conditions. Specifically, when the sand density on the PV module surface increases from 0 to 40g/m², there is a 32.2% reduction in maximum output power. At a wind speed of 15m/s, this reduction was found consistent across all wind speed categories. Furthermore, the trend of the module filling factor rel-ative to sand accumulation density contrasts with the module temperature trend under analogous conditions. Notably, the filling factor reached its apex at a sand accumulation density of 35g/m², which corresponded to the module temperature's nadir during the experiment.

Imidazoline derivatives, such as xylometazoline, naphazoline, tetryzoline, tramazoline or oxymetazoline play an important pharmacological role as nasal drops in the symptomatic treatment of rhinitis. When comparing the toxicological data of these substances, it is noticeable that Oxymetazoline has an LD₅₀ value which is two orders of magnitude lower than all other imidazoline derivatives. Thus, ten vials of commercially available oxymetazoline nasal drops already contain a lethal amount. An explanation for this unusually high toxicity has not yet been found.

This study describes the implementation of IoT sensors in drinking water systems and fog collector systems in low-income communities in Ecuador. The influence and handling of these sensors are analyzed, as well as the materials and methods used in their implementation. The importance of validating the accuracy and reliability of IoT sensors compared to professional devices, especially in mountain areas, is highlighted. In addition, it is mentioned that the cost-benefit of using IoT sensors in fog catchers and drinking water networks depends on several factors, such as the scale of the project, specific objectives, and available resources. Finally, it is highlighted that the use of IoT sensors in smart construction and water collection systems has proven to be beneficial in preventing effects on the operation.

Many sand scorpions are faithful to burrows they dig, however, it is unknown how these animals get back home after hunting excursions. Of the many mechanisms of homing that exist, path integration (PI) is one of the more common tools used by arachnids. In PI, an animal integrates its distance and direction while leaving its home, enabling it to compute an approximate home-bound vector for the return trip. The objective of our study was to test whether scorpions use PI to return home under absolute darkness in the lab. We first allowed animals to establish burrows in homing arenas. Then, after they left their burrow, we recorded the scorpion’s location in the homing arena before we transferred it to the center of a testing arena. We used overhead IR cameras to record its movements in the testing arena. If scorpions exhibited PI, we predicted they would follow a vector in the test arena that approximated the same angle and distance from the capture point to their burrow in their home arena. However, under the conditions of this experiment, we found no evidence that scorpions moved along such home-bound vectors. We speculate that scorpions may need a reliable reference cue to accommodate path integration.

Quantitative measurements of performance parameters has the potential to increase consistency and enhance performance of the surfaces as well as to contribute to the safety of horses and riders. This study investigates how factors known to influence the performance of the surface, incorpo-ration of a drainage package, control of the moisture control, and introduction of a geotextile reinforcement, affect quantitative measurements of arena materials. The measurements are made by using affordable lightweight testing tools which are readily available or easily constructed. Sixteen boxes with arena materials at a consistent depth were tested with the Going Stick (GS), both penetration resistance and shear, the impact test device (ITD), and the rotational peak shear device (RPS). Volumetric moisture content (VMC %) was also tested with time-domain reflectometry (TDR). Results obtained using GS, RPS, ITD, and TDR indicate that the presence of the drainage package, moisture content, and geotextile addition were detected. Alterations due to combinations of treatments could also be detected by GS, ITD, and TDR. While the testing showed some limi-tations of these devices, the potential exists to utilize them for quality control of new installations as well as for the monitoring of maintenance of the surfaces.

One of the interactions that has been studied in recent decades under the ecohydrological approach is infiltration, which is difficult to determine because the existing methods for estimation depends on certain variables that are difficult to establish or identify, and in other cases, the implementation of instrumentation is expensive. Given this, saturated hydraulic conductivity has been the descriptive variable of the infiltration process by recent authors, being understood as the conduction of water that occurs through the soil and its composition through the vegetation cover. The present design generated an easily accessible portable instrumentation model for the monitoring and collection of infiltration data in situ for basins and ecosystems with different land uses, in an automated manner with the objective of determining the vegetation patterns necessary to sustain the infiltration function. The INDI-INECOL tension infiltrometer [1] was chosen as the reference instrument. It evaluates the saturated hydraulic conductivity based on a column of water that descends through the system and it is exchanged in the soil by the air between the pores. To automate data collection, a measurement system has been proposed through a SCADA system, which is defined as a control, action, decision, storage and data recording system. This system collects field data from a sensor VL053L0X connected to a master station, in our case an Arduino board UNO, connected through the serial port and by a graphical user interface programmed on Python, to display, storage and enrichment of the sensor data and finally to be exported in files suitable for Microsoft Excel.

Different toll collection types of vehicles and different distribution of tollbooths lead to the toll plaza diverging area becoming a typical vehicle weaving area with frequent crossing behaviors and conflicts on highways. This study aims to identify contributing factors to conflict risks of four vehicle-following patterns in a toll plaza diverging area by developing random parameters ordered logit models with heterogeneity in means and variances. The model can flexibly capture the unobserved heterogeneity of the contributing factors in different vehicle-following patterns. Real-world vehicle trajectory data obtained from the toll plaza diverging area in Nanjing, China, are used for model estimation. The results show that vehicle-following patterns with the same toll collection types have higher percentage of severe conflict risks. The average acceleration of the following vehicles, lane marking indicator, the initial lanes and lane-changes of vehicles are significantly associated with the collision risk levels. The standard deviation of surrogate safety measures of all vehicles in sub-segments are found differ significantly between vehicle-following patterns. Furthermore, a series of likelihood ratio tests are adopted to test the spatial dependence in sub-segments of the diverging area. The findings of this study could provide valuable information for safety improvement in toll plazas.

Industrial hemp (Cannabis sativa L.) is an attractive candidate for sustainable pest management due to its abundance of bioactive compounds with potential pesticidal properties. Solvent choice has a significant impact on the extraction efficiency of bioactive compounds. Deep Eutectic Solvents (DESs) are gaining popularity in extraction because they are safe and environmentally friendly, making them viable alternatives to organic solvents (OSs). This research first compared the extraction efficiency of OSs on the extraction of phytochemicals from the infloresences of two hemp varieties, Citrus and Cherry Dwarf. Inflorescences were extracted using three OSs, ethanol, ethyl acetate, and hexane. The highest level of cannabidiol (CBD; 0.69%) was extracted from Cherry Dwarf using ethanol while the level of delta-9 tetrahydrocannabinol THC (0.19%) was essentially the same in both. Therefore, Cherry Dwarf was selected to compare the extraction efficiency of DESs to the OSs. The DESs were choline chloride/ethylene glycol, citric acid/ethylene glycol, menthol/lauric acid, choline chloride/urea and choline chloride/glycerol. In the targeted analysis, choline chloride/ethylene glycol extracted the highest amount of CBD (0.87%) followed by choline chloride/urea (0.78%). As some DESs outperformed ethanol, the popular solvent for extracting cannabinoids, DESs are viable candidates to replace organic solvents.

The vacuum preloading method effectively strengthens the soft soil foundations with vertical drainage, which will produce a smear effect when laying sand drains. Meanwhile, the seepage of pore water and soil deformation during consolidation exhibits nonlinear characteristics. Therefore, based on Gibson's 1D large strain consolidation theory, this paper developed a more generalized large strain radical consolidation model of sand-drained soft foundations under free strain assumption. In this system, the double logarithmic compression permeability relationships for soft soils with large strain properties, the variation of the radical permeability coefficient in the smear zone, and the effect of the non-Darcy flow were all included. Then, the partial differential control equations were numerically solved by the finite difference method and validated with existing radical consolidation test results and derived analytical solutions. Finally, the influences of relevant model parameters on consolidation are discussed. The analysis shows that the greater the maximum dimensionless vacuum negative pressure P0, the faster the consolidation rate of sand-drained foundations. Meanwhile, the decrease in the negative pressure transfer coefficient k1 will result in a decreasing final settlement amount. Moreover, the consolidation rate of sand-drained foundations is slower considering the non-Darcy flow, but the final settlement is unaffected.

We make use of generalized iterations of the Sacks forcing to define cardinal-preserving generic extensions of the constructible universe L in which the axioms of ZF hold and in addition either 1) the parameter-free countable axiom of choice AC* fails, or 2) AC* holds but the full countable axiom of choice AC fails in the domain of reals. In another generic extension of L, we define a set X⊆P(ω), which is a model of the parameter-free part PA2* of the 2nd order Peano arithmetic PA2, in which CA(Σ21) (Comprehension for Σ21 formulas with parameters) holds, yet an instance of Comprehension CA for a more complex formula fails. Treating the iterated Sacks forcing as a class forcing over $L_{\omega_1}$, we infer the following consistency results as corollaries. If the 2nd order Peano arithmetic PA2 is formally consistent then so are the theories: 1) PA2 + negation of AC*, 2) PA2 + AC* + negation of AC, 3) PA2* + CA(Σ21) + negation of CA.

Kersting’s groundnut is an important source of protein and essential nutrients that contribute to food security in West Africa. However, the crop is still underexploited by the populations and under-researched by the scientific community. This study aimed to investigate the genetic diversity and population structure of 217 Kersting’s groundnut accessions from five origins using 886 DArTseq markers. Gene diversity was low and ranged from 0.049 to 0.064. The number of private alleles greatly varied among populations (42–192) and morphotypes (40–339). Moderate to very high levels of selfing and inbreeding were observed among populations (s=56–85%, F_IS=0.389–0.736) and morphotypes (s=57–82%, F_IS=0.400–0.691). Moreover, little to very high genetic differentiations were observed among populations (0.006≤F_IS≤0.371) and morphotypes (0.029≤F_IS≤0.307). Analysis of molecular variance partitioned 38.5% of the genetic variation among and 48.7% within populations (P<0.001). Significant isolations by distance were detected between populations (R²=0.612, P=0.011) and accessions (R²=0.499, P<0.001). Discriminant analysis of principal components and neighbour joining consistently distinguished eight distinct clusters. These data provide a global picture of the existing genetic diversity for Kersting’s groundnut and will guide the choice of breeding strategies to increase production.