Lightweight composite sandwich structures are laminated composite structures that are composed of thin stiff face sheets bonded to a thicker lightweight core in between. These structures have high potential to be used in marine, aerospace, defense and civil engineering applications due to their high strength to weight ratios and energy absorption capacity.In this study, composite sandwich structures were developed with carbon fiber reinforced polymer composite face sheets and aluminum honeycomb core materials with various thicknesses. Carbon fiber/epoxy composite face sheets were fabricated with lamination of [0/90]_s carbon fabrics by vacuum infusion technique. Al honeycomb layers were sandwiched together with the face sheets using a thermosetting adhesive. Mechanical tests were carried out to determine the mechanical behavior of face sheets, Al cores and the composite structure. Effect of core thickness on the mechanical properties of the sandwich was investigated.

The use of interleaving material with viscoelastic properties is one of the most effective solutions to improve the damping capacity of CFRP laminates. Improving composite damping without threatening mechanical performance is challenging and the use of nanomaterials should lead to the target. In this paper, the effect of a nanostructured interlayer based on Graphite Nanoplatelets (GNPs) on the damping capacity and fracture toughness of CFRP laminates has been investigated. High-content GNP/Epoxy (70wt/30wt) coating was sprayed on the surface of CF/Epoxy prepregs at two different areal weight (10 and 40 g/m2) and incorporated at the middle-plane of a CFRP laminate. The effect of the GNP areal weight on viscoelastic and the mechanical behaviour of the laminates was investigated. Coupons with low-areal weight GNP interlayer showed a 25% increase in damping capacity with a trivial reduction of the elastic modulus. Moreover, a reduction in interlaminar shear strength (ILSS) and fracture toughness (both mode I and mode II) was observed in the composites with GNPs interlayer. GNPs alignment and degree of compaction reached during process were found as key parameters on material performances. By increasing the areal weight a mitigation on the mechanical performances drop was achieved (-15%).

Epoxy was blended with benzoxazine resin and aluminum trihydrate (ATH) additive to render flame retardancy while maintaining mechanical properties. The ATH was modified using three different silane coupling agents and then added to 60/40 epoxy/benzoxazine mixtures. The effect of blend compositions and surface modification on flame retardant and mechanical properties of the composites was investigated by UL94, tensile, and shear tests. Resin mixtures containing more than 40 wt% benzoxazine revealed a UL94 V-1 rating with enhanced tensile and shear strength. Upon addition of 20 wt% ATH to 60/40 epoxy/benzoxazine, a V-0 rating was achieved. The lowered tensile and adhesive properties of the composites in the presence of ATH were improved by modifying the ATH surface using silane coupling agents.

Integrating nanomaterials like carbon nanotubes (CNTs) and iron oxide (Fe₃O₄) into epoxy composites has significant interest due to their potential to enhance mechanical properties. This study evaluates the impact of dispersion quality on the mechanical performance of CNT/Fe₃O₄/Epoxy composites, comparing stirring and sonication methods at three different loadings: 0.1, 0.3, and 0.5 wt.%. Tensile testing revealed that sonicated composites consistently outperformed stirred composites, with a significant increase in elastic modulus and ultimate tensile strength (UTS). However, fracture strain decreased in both composite types compared to pure epoxy, with sonicated composites experiencing a more significant reduction than stirred composites. These results underscore the importance of high-quality dispersion for optimizing mechanical properties.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

Fiber-opening treatment of commingled yarns consisting of thermoplastic nylon fibers and carbon fibers could produce superior CFRTP, but few studies toward that end have been conducted. In this study, we investigated whether an open weave fabric consisting of commingled yarns made of carbon and nylon fibers could shorten the impregnation distance of resin to carbon fibers, and there are few reports on the design of fabrics by opening carbon fiber bundles consisting of commingled yarns. From this study, following are cleared. The impregnation speed of the nylon resin on the carbon fiber was very fast, less than 1 minute. As the molding time increased, the tensile strength and tensile fracture strain slightly decreased and the nylon resin deteriorated. The effects of molding time on flexural strength, flexural modulus, and flexural fracture strain were negligible. From the cross-sectional observation conducted to confirm the impregnation state of the matrix resin, no voids were observed in the molded products regardless of molding time or molding pressure, indicating that resin impregnation into the carbon fiber bundle of the open-fiber mixed yarn fabric was completed at a molding pressure of 5 MPa and a molding time of 5 min.

A study of cryogenic drilling in sandwich composites has been carried out. Materials used have been carbon fiber reinforced polymer sandwich sheets with inner foamed polyvinyl chloride core, composites with aerospace, marine, construction and automotive applications, including protec-tion structure of Polar engineering equipment. Experimental tests have been performed in lam-inates with 12 mm and 6 mm of thickness, drilling with liquid nitrogen as refrigerant to reach temperatures below -120ºC under different cutting conditions, in particular, drill rotation speeds between 2000 rpm and 6000 rpm and feed rates between 200 mm/min and 600 mm/min. Variables as thrust forces and circularity error have been measured, due to the importance of its effect on the hole quality, as an operation prior to a possible assembly. A design of experiments has been allowed determining relationships between variables, identifying the influence of cutting condi-tions on the thrust force and the circularity at inlet and outlet holes.

It is well known that fiber sizing is one of the most important component in the manufacturing of composites, and it does affect the mechanical properties including strength and stiffness. In this work, the influence of fiber sizing levels on the mechanical properties of carbon fibers (CF) is reported at room temperature by using single fiber tensile testing (Favimat+), single fiber pullout testing (SFPO), and interfacial elemental analysis using X-ray photoelectron spectroscopy (XPS). Standard modulus of CF (7±0.2 μm in diameter) were sized using two Michelman commercially available sizing formulations. The average solid content for each sizing formulation is 26.3 ± 0.2% and 34.1 ± 0.2%, respectively. HEXION RIMR 135 with curing agent RIMH 137 was used as a model thermoset epoxy matrix during the SFPO measurements. A predictive engineering fiber sizing methodology is also developed. Sizing amounts of 0.5, 1, and 2 wt. % on the surface of the fiber is achieved for both sizing formulations. For each fiber sizing level, 50 single fiber tensile testing experiments and 20 single fiber pull-out tests were conducted. The ultimate tensile strength (σult) of the carbon fibers and the interfacial shear strength (τ_app) of the single fiber composite were analyzed. it is also investigated the effect of the sizing levels on the interfacial shear stress and the O/C (Oxygen/Carbon) surface composition ratio. As a result, generalized fiber sizing and characterization methods were established. The developed methods can be used to characterize the strength and interfacial shear strength of any man-made fibers with different sizing formulations and solid contents, irrespective of the matrix i.e. thermoset or thermoplastic.

In this work, three different types of sandwich structures were manufactured using Formica sheet (a paper-based sheet) as skin and perlite/sodium silicate foam as core with/without the paper honeycomb. The sandwich structures were fabricated by attaching Formica sheets on both sides of the honeycomb, perlite/sodium silicate foam, and perlite/sodium silicate foam-filled honeycomb core panels. The flexural characteristics were studied by a three-point bending test and the thermal conductivity was measured using Lee’s thermal conductivity apparatus. The results demonstrated a significant improvement in flexural properties, including core shear stress, facing stress, bending stress, and energy absorption, when incorporating the paper honeycomb reinforcement. The thermal conductivity and flexural properties were found to be well-compatible with the existing building materials for similar applications in the literature. The failure investigation revealed that the sandwiches with paper honeycomb only prematurely failed due to core buckling, whereas the foam-filled honeycomb core-based sandwiches were able to sustain higher loads, exhibiting material failures such as core shear failure, skin rapture, and delamination. It is found that the foam-filled paper honeycomb sandwich structures can withstand higher bending loads compared to foam core-based and paper honeycomb-based sandwich structures. These developed sandwiches offer potential as green materials due to the characteristics of their constituent materials and can find valuable applications in the building thermal insulation.

Due to their remarkable intrinsic physical properties, carbon nanotubes (CNTs) can enhance mechanical properties and confer electrical and thermal conductivity to polymers currently investigated for use in advanced applications based on thermal management. An epoxy resin filled with varying concentrations of CNTs (up to 3 wt.%) was produced and experimentally characterized. The electrical percolation curve identified two critical filler concentrations: 0.5 wt%, near the electrical percolation threshold, suitable for exploring mechanical and piezoresistive properties, and 3 wt% for investigating thermo-electric properties due to the Joule effect with applied voltages ranging from 70V to 200V. Numerical models were developed using multiphysics simulation software. Once validated with experimental data, these models were used to investigate additional physical properties of the composites. Furthermore, a statistical approach based on the design of experiments (DoE) was employed to examine the influence of certain thermal parameters on the final performance of the materials. The purpose of this research is to promote the use of contemporary statistical and computational techniques alongside experimental methods to enhance understanding of materials science. New materials can be identified through these integrated approaches, or existing ones can be more thoroughly examined.

With the development of nuclear technology application, radiation safety has been widely concerned, and there is an urgent need for novel shielding materials. Among the various options available, non-lead organic composite shielding material has emerged as a promising solution in the field of radiation shielding due to its high strength, easy processing, and light weight. In this study, tungsten/epoxy resin (W/EP) composite samples with tungsten weight fraction from 0% to 60% were prepared. The shielding and mechanical properties of W/EP composites were investigated. The results show that the results showed that the higher the tungsten content, the greater the shielding capacity of W/EP composites, particularly for low-energy gamma ray (γ) shielding. However, the addition of tungsten reduces the impact strength and tensile properties of the material. Overall, for 300 keV γ-ray, W/EP with 30% tungsten content has comparable shielding capacity to ordinary concrete. W/EP composite materials can serve as shielding materials for low-energy γ-rays.

Nonwovens made of recycled carbon fibers (rCF) and thermoplastic (TP) fibers have excellent economic and ecological potential. In contrast to new fibers, recycled carbon fibers are significantly cheaper and the CO2 footprint is mostly compensated by energy savings in the first product life cycle. The next step for this promising material is its industrial serial use. Therefore the process chain from fiber to composite material is analyzed. Initially rCF length at different positions during the carding process is measured. Thereafter the influence of the TP fibers onto processing, fiber shortening and mechanical properties is evaluated. At last several nonwovens with different TP fibers and fiber volume contents between 15 vol.-% and 30 vol.-% are produced, consolidated by hot pressing and tested by 4-point bending to determine the mechanical values. The fiber length reduction ranges from 20.6 % to 28.4 %. TP fibers cushion the rCF against mechanical stress but hold rCF fragments back due to their crimp. The resulting bending strength varies from 301 MPa to 405 MPa and the stiffness from 16.3 GPa to 30.1 GPa. Design recommendations for reduced fiber shortening are derived as well as material mixtures which offer better homogeneity and higher mechanical properties.

Fused deposition modeling (FDM) is widely applied in various fields due to its affordability and ease of use. However, it faces challenges such as achieving high surface quality, precise dimensional tolerance and overcoming anisotropic mechanical properties. This paper analyzes and compare the machinability of 3D printed PLA, PETG and carbon fiber reinforced PETG focusing on surface roughness and burr formation. A design of experiments (DoE) with a full factorial design was used, considering three factors: rotation speed, feed rate and depth of cut. Each factor had different levels: rotational speed at 3000, 5500 and 8000 rpm; feed rate at 400, 600 and 800 mm/min; and depth of cut at 0.2, 0.4, 0.6, and 0.8 mm. Machinability was evaluated by roughness and burr height using a profilometer for all the materials under the same milling conditions. To evaluate the statistical significance of the influence of various processing parameters on surface roughness and burr formation in 3D printed components made of three different materials PLA, PETG and carbon fiber reinforced PETG, an analysis of variance (ANOVA) test was conducted. This analysis investigated whether variations in rotational speed, feed rate and depth of cut resulted in measurable and significant differences in machinability results. Results showed that milling parameters significantly affect roughness and burr formation, with optimal conditions for minimizing any misalignment highlighting the trade-offs in parameter selection. These results provide insights into the post-processing of FDM-printed materials with milling, indicating the need for a balanced approach to parameter selection based on application-specific requirements.

As a member of smart materials, electrorheological elastomers (EREs) formed by pre-treating active electrorheological particles are attracting more and more attention. In this work, four Mg-doped strontium titanate particles with spherical, dendritic, flake-like and pinecone-like morphorlogies were obtained by hydrothermal and low-temperature co-precipitation. XRD, SEM, Raman and FT-IR were used to characterize the obtained products. The results showed that the sizes of Mg-doped strontium titanates are about 1.5‒2.0 μm, and the phase structure are dominated by cubic crystal. These Mg-doped strontium titanates were dispersed in a hydrogel composite elastic medium. Then, Mg-doped strontium titanate/glycerol/gelatin electrorheological composite hydrophilic elastomers were obtained with or without electric field. The electric field response properties of Mg-doped strontium titanate composite elastomers were investigated. It concluded that dendritic Mg-doped strontium titanate composite elastomers is high-performance EREs. And the maximum value of energy storage modulus of Mg-doped strontium titanate composite elastomers has achieved 8.70 MPa. This high electrorheological performance of the products is helpful for their applications in vibration control, force transducers, smart structures, dampers, and other fields.

In the process of use and manufacture, carbon fiber foam sandwich structures were often damaged by low-energy impact, resulting in performance degradation. Therefore, it was necessary to study the damage caused by low-speed impact of composite sandwich structures. In this paper, based on Hashin failure criterion, an equivalent finite element model of carbon fiber foam sandwich panel under low velocity impact was established. The model was used to simulate the damage of foam sandwich panel with [±45°/±45°/ (core) /±45°/±45°] ply structure under the impact energy of 10.58J, 21.17J, 31.75J and 42.34J. The simulation results of impact damage depth were compared with the experimental results. The error was less than 10%, which proved the rationality of the impact equivalent model. The model was used to predict and analyze the damage of foam sandwich panels with [±45°/ (core) /±45°], [±45°/ (0°, 90°) / (core) /±45°] and [±45°/ (0°, 90°) (core) / (0°, 90°) /±45°] ply structures under 21.17J impact energy. By comparing and analyzing the damage situation, impact force response time and impact velocity response time, the low energy impact resistance was analyzed. The results showed that increasing the number of ply structure of [±45°] can reduce the impact damage degree and improve the bearing capacity of sandwich panels.

Lightweight component design is effectively achievable through the sandwich structures, many past research studies in the aerospace and racing sectors (since 1920s) has proven it. To extend their application into automotive and other transport industries, the manufacturing cycle times must be reduced. This can be achieved by thermoplastic sandwich materials of continuous fibre-reinforced thermoplastic (CFRTP) cover layers and thermoplastic honeycomb cores. To widespread the application of flat thermoplastic-based sandwich panels into complex parts, a novel forming technology was developed by the Fraunhofer Institute of Microstructure of Materials and Systems (IMWS). For an increase in reproducibility of the sandwich component production and a decrease in manufacturing defects, numerical modelling methods and experimental validation are needed. The finite element (FE) modelling of this thermoforming process is a thermo-mechanical assignment with all three: material, geometry, and boundary non-linearities. In the scope of this work, the material behavior of different sandwich components (cover layers, honeycomb core, interface) under thermo-mechanical loads is characterized in detail, and a complex numerical model is developed to describe the thermoforming process of thermoplastic-based sandwich laminate. The critical forming condition like wrinkling that occurs due to friction in a sandwich or poor intra-ply shear in cross-ply studied, validated, and optimized. A thermoplastic sandwich made of polypropylene (PP) honeycomb core and polypropylene glass fibre (PP/GF) cross-ply as cover layers was used for this study, and numerical modelling was executed in LS-DYNA software.

The damage caused by global warming is rapidly increasing, and its adverse effects become more evident with each passing day. Although it is known that the use of alternative binder materials in concrete would decrease this negative effect, reluctance to new composites continues. Waste use plays a vital role in sustainability studies. In this study, pure cement paste was prepared and enriched with carbon fiber. This study investigated the wide range of volume fraction of carbon fiber in cement-based composites. Two different industrial wastes, marble dust, and bottom ash were chosen and mixed with cement and four different (0.3%, 0.75%, 1.5%, and 2.5%) carbon fiber volume fractions. Based on physical, mechanical, and durability tests at 7, 28, and 56-days of curing, the composites were resistant to sulfate and seawater attack. The 0.75% carbon fiber addition seems to be an optimum volume percentage beyond which both physical and mechanical properties were adversely affected. The composites with 0.75% carbon fiber have reached 48.4 MPa and 47.2 MPa at 56-days of curing for marble dust and bottom ash mixture groups, respectively.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

The effects of carbon fiber hybridisation on the thermal properties of woven kenaf reinforced epoxy composites kenaf fibre were studied. Woven kenaf hybrid composites at the different weave designs of plain and satin, and fabric count of 5 × 5 and 6 × 6 were manually prepared by vacuum infusion technique. Thermal properties of pure carbon fibre and hybrid composites were conducted by using thermogravimetric analyser (TGA) and differential scanning calorimeter (DSC). It was found that at high kenaf fibre content showed better thermal stability while the highest thermally stable was found in pure carbon fibre composite. The TG and DTG results showed that the amount of residue decreased in plain-designed hybrid composite compared to satin-designed hybrid composite. The DSC data revealed that the presence of woven kenaf increase decomposition temperature.

In this study, the mechanical and piezoresistive properties of mortars reinforced with carbon nanotubes (CNTs) and carbon micro fibers (CMFs) are determined. Silica fume as well as a polymer with polyalkylene glycol graft chains were used as dispersant agents for the CNTs and CMFs incorporation into the cement paste. The mechanical properties of the mortar composites were investigated in respect to their flexural and compressive strength. A four-probe method was used for the estimation of their piezoresistive response. The test outcomes revealed that the combination of the dispersant agents along with a low content of CNTs and CMF by weight of cement (bwoc) result in the production of a stronger mortar with enhanced mechanical performance and durability. More specifically, there was an increase in flexural and compressive strength up to 38% and 88%, respectively. Moreover, the piezoresistive response of the reinforced cementitious materials was attributed to the variation of electrical resistivity due to tunneling transport of electrons stemming from two different mechanisms due to the incorporation of the conductive admixtures (CNTs and CMF). This work aims to contribute to the progress acceleration in the field of developing structural materials with self-sensing and electrical actuation related properties.

Advanced Finite Element (FE) modeling and simulations were performed on vehicular crashes into a Three-bar Metal Bridge Rail (TMBR). The FE models of a sedan, a pickup truck, and a TMBR section were adopted in the crash simulations subject to Manual for Assessing Safety Hardware (MASH) Test Level 2 (TL-2) and Test Level 3 (TL-3) requirements. The test vehicle models were first validated using full-scale physical crash tests conducted on a two-bar metal bridge using a sedan and a pickup truck with similar overall physical properties and sizes to their respective vehicles used in the simulations. The validated vehicular models were then used to evaluate the crash performance of the TMBR using MASH Evaluation Criteria for structural adequacy, occupant risk, and post-impact trajectory. The TMBR met all MASH TL-2 requirements but failed to meet the MASH TL-3 Criteria H and N requirements when impacted by the sedan. The TMBR was also evaluated under in-service conditions (behind a 1.52-m wide sidewalk) and impacted by the sedan under MASH TL-3 conditions. The simulation results showed that the TMBR behind a sidewalk met all safety requirements except for the occupant impact velocity in the longitudinal direction, which exceeded the MASH limit by 3.93%.

The excellent properties of carbon fibers, in combination with the high price of carbon fibers, makes it interesting to recycle these fibers. Pyrolysis is already an established recycling method to recover the carbon fibers, but in this process also the sizing is removed which could result in lower mechanical properties because of bad adhesion between the fiber and matrix. In this study, recycled carbon nonwoven reinforcements made from pyrolyzed carbon fibers were pre-treated in order to improve the mechanical properties of recycled carbon polyamide and recycled carbon polypropylene composites. The pre-treatment involves applying a to the matrix adapted primer coating to the nonwoven by spraying. Via compression molding, polyamide and polypropylene composites were prepared with and without pretreatment. The tensile and interlaminar shear strength of these composites were measured to determine the effect of the pretreatment. Results revealed that both strengths could be increased by pretreatment of the carbon nonwoven and the increase was largest for the PP composites.

Poor interlaminar fracture toughness has been a major issue in glass fiber-reinforced epoxy resin (GF/EP) laminate composites. In this paper, soft carboxy-terminated liquid nitrile (CTBN) rubber particles and rigid nano-SiO2 are used to toughen the epoxy resin (EP) matrix to improve the interlayer properties of GF/EP laminate composites. The effects of adding two toughening agents on the mechanical and interlayer properties of GF/EP laminates were studied. The results showed that adding the two kinds of particles improved the mechanical properties of the epoxy matrix. When the additional amount of flexible CTBN rubber particles was 8wt%, and the rigid nano SiO2 was 0.5wt%, the fracture toughness of the matrix resin was increased by 215.8%, and the tensile strength was only decreased by 2.3% compared with the pure epoxy resin. On this basis, the effects of two kinds of particles on the interlayer properties of GF/EP composites were studied. Compared with the unmodified GF/EP laminates, the interlayer shear strength and mode Ⅰ interlayer fracture toughness is significantly improved by toughening agent, and the energy release rate GIC of interlayer shear strength and interlayer fracture toughness is increased by 109.2%, and 86.8%, respectively.

In this study, 10%PTFE/PEEK blend were modified by potassium titanate whisker (PTW) and chopped glass fiber (GF), respectively. The blends were prepared by three-screw extruder. Through the investigation of thermal stability, tribological properties, mechanical properties and rheological behavior, the effects of reinforcing agents were determined. The results illustrated that the mechanical properties of 10%PTFE/PEEK blend can be dramatically improved by adding reinforcing agent of PTW or GF, and the reinforcing effect of GF was especially obvious. As for tribological properties, 1% addition was the best proportion. The friction coefficient and wear rate of the blend with 1% PTW were 0.283 and 4.97 × 10^-6 mm³/N · m, which decreased by 7.2% and 21% compared with those of the blend without reinforcing agent.

In this study, a new structure is proposed based on the body-centered cubic (BCC) lattice structure: adding a cubic truss in the center of the BCC structure, which is denoted by TLC (Truss-lattice-cube). The different dimensions of the central cube can affect the mechanical properties of the lattice structure notably. With a fixed length (15mm) of a unit cell, the optimal size for the central cube is determined to be 5 mm. Quasi-static compressive tests are performed on specimens made of Polylactic Acid (PLA) using additive manufacturing technology. The deformation characteristics of the new structure is analyzed in detail by experiments and numerical simulations. Compared to the BCC structure, the mechanical properties of the TLC structure are significantly improved. The initial flow stress of the TLC has been increased by 122% at a strain of 0.1; the specific strength has been enhanced by 293% at a strain of 0.5; and the specific energy absorption has been improved by 312% at the strain of 0.6. Printing defects in the lattice structure could deteriorate the mechanical property remarkably. In this work, incorporation of microcracks into the finite element model makes the simulation capture the influence of printing defects and improve the predictive accuracy of simulation significantly.

This paper considers a new approach to the modeling of the vacuum infusion process at the manufacturing three-dimensional composite parts of complex shape. The developed approach and numerical methods are focused on the reliable prediction with the needed accuracy and elimination the unrecoverable defect of composite structure such as the dry spots. The paper presents some experimental results, which demonstrate two cases of dry spots formation in large aircraft composite panels, and analyses the reasons of these defects arising. Our numerical technique is based on the vacuum infusion of the liquid resin into porous preform as the two phase flow, which is described by the phase field equation coupled with the Richards equation describing the fluid motion in unsaturated soils with spatially varied pressure dependant porosity and saturation. This problem statement allowed to correctly reconstruct the resin front motion and formation of inner and outer dry spots depending on its movement. For the rapid detection of preform zones that are suspicious for defect formation two indicators calculated during process simulation are proposed and tested at the numerical experiments. The auxiliary program tool has been developed in MATLAB environment to correctly detect the times of formation, localization and dimensions of the arising dry spots by using the results of the finite element model simulation.

Fiber-reinforced mycelium (FRM) composites offer an innovative and sustainable approach to construction materials for architectural structures. Mycelium, the root structure of fungi, can be combined with various natural fibers (NF) to create a strong and lightweight material with environmental benefits. Incorporating NF like hemp, jute, or bamboo into the mycelium matrix enhances mechanical properties. This combination results in a composite that boasts enhanced strength, flexibility, and durability. Natural FRM composites offer sustainability through the utilization of agricultural waste, reducing the carbon footprint compared to conventional construction materials. Additionally, the lightweight yet strong nature of the resulting material makes it versatile for various construction applications, while its inherent insulation properties contribute to improved energy efficiency in buildings. Developing and adopting natural FRM composites showcase a promising step towards sustainable and eco-friendly construction materials. Ongoing research and collaboration between scientists, engineers, and the construction industry will likely lead to further improvements and expanded applications. This article provides a comprehensive analysis of the current research and applications of natural FRM composite for innovative and sustainable construction materials. Additionally, the paper reviews the mechanical properties and potential impacts of these natural FRM composites in the context of sustainable architectural construction practices. Recently, the relevance of mycelium-based materials has extended beyond their original fields of microbiology and mycology to architecture.

The dynamic behaviour of a machine tool (MT) directly influences the machining performances. The adoption of lightweight structures may reduce the effects of undesired vibrations and increasing the workpiece quality. This paper aims to present and compare a set of hybrid materials that may be excellent candidate to fabricate the MT moving parts. The selected materials have high dynamic characteristics and capacity to damp mechanical vibrations. In this way, starting by the kinematic model of a milling machine that highlights the main critical factors, this study paper evaluates a number of prototypes made of Al Foam sandwiches (AFS), Al Corrugated sandwiches (ACS) and materials reinforced by carbon fibres (CFRP). A set of prototypes has been fabricated, represented the Z-axis ram of a commercial milling machine. The static and dynamical properties have been evaluated by using both FE simulations and experimental tests. The obtained results show that the proposed structures may be a valid alternative to the conventional materials of MT moving parts, increasing machining performances. In particular, the AFS prototype highlighted a damping coefficient that is 20 times greater than a conventional ram (e.g. steel). The CFRP structure is able to satisfy the machining requirements with a reduced weight of 48.5%, while the ACS prototype showed a good trade-off between stiffness and damping.

The interfacial interface between the fibers and the matrix plays a key role for epoxy matrix composites and short recycled randomly arranged fibres. This study used short recycled carbon fiber (RCF) as a filler. Plasma treatment was used for carbon fiber surface treatment. This treat-ment was performed using radio (RF) and microwave (MW) frequencies at the same pressure and atmosphere. Appropriate chemical modification of the fiber surfaces helps to improve the wettability of the carbon fibers and, at the same time, allows the necessary covalent bonds to form between the fibers and the epoxy matrix. The effect of the plasma treatment was analyzed and confirmed by XPS analysis, Raman microscopy, SEM, TEM and wettability measurements. Composite samples filled with recycled carbon fibers with low concentrations (1 wt%, 2.5 wt% and 5 wt%) and high concentrations (20 wt% and 30 wt%) were made from selected treated fi-bers. The mechanical properties (impact toughness, 3PB) were analyzed on these samples. It was found that the modulus of elasticity and bending stress increase with the increasing content of recycled carbon fibers. A more significant change in impact strength occurred in samples with low concentration.

The use of plant fibers as reinforcement in composites with the aim of totally or partially replacing synthetic fibers has received significant attention in the last years. However, one of the disadvantages of the use of these fibers in polymeric composites is associated to the fact that they are hydrophilic, resulting in poor adhesion with most matrices when in the presence of moisture. In addition, another problem encountered is the lower strength of this type of fiber and, as a solution to minimize these problems, the composite can be hybridized by adding layers of natural and synthetic fibers and the use of resin protection along the thickness of the composite. (Lateral protection) to reduce moisture absorption by the laminate. The objective of this work is to obtain composites formed by five layers of reinforcement and terephthalic polyester matrix, one of which is reinforced only with short glass fiber-E blanket, another reinforced only with jute fiber and a third hybrid containing the fibers. Two types of reinforcements with interlayer layers. Afterwards, the loss of mechanical properties was observed when these materials were immersed in distilled water, with and without lateral protection, until reaching saturation. We evaluated parameters such as the influence of configuration type and environmental conditions, such as the amount of water absorption. The obtained results show that the hybrid composite obtained a behavior close to the composite containing only fiberglass, and better than the one containing only jute fiber and that the absorption was smaller in the samples with side protection.

Structural evolution, mechanical and tribological properties of Al-Mg alloy admixed with 5, 10 and 15 vol.% of iron powder using multi-pass friction stir processing (FSP) have been studied. Homogeneous distribution of intermetallic compound (IMC) particles were achieved after 4 FSP passes what resulted in increasing the stir zone hardness and ultimate tensile stress with simultaneous loss in the ductility. The reinforcement of the aluminum alloy matrix with IMCs allowed reducing wear at the same magnitude of friction. Subsurface composite tribological layer was formed on the FSPed samples as a result of rubbing against a steel counterbody.

To improve the interfacial bonding of sisal fiber reinforced polylactide biocomposites, polylactide (PLA) and sisal fibers (SF) were melt-blended to fabricate bio-based composites via in situ reactive interfacial compatibilization with the addition of an epoxy-functionalized oligomer (ADR). The FTIR analysis and SEM characterization demonstrated that PLA molecular chain was bonded to the fiber surface and epoxy-functionalized oligomer played a hinge-like role between sisal fibers and PLA matrix, which resulted in improved interfacial adhesion between fibers and PLA matrix. The interfacial reaction and microstructures of composites were further investigated by thermal and rheological analyses, which indicated that the mobility of the PLA molecular chain in composites was restricted because of the introduction of ADR oligomer, which in turn reflected the improved interfacial interaction between SF and PLA matrix. These conclusions were further investigated by the calculated activation energies of glass transition relaxation (△Ea) of composites via dynamic mechanical analysis. The mechanical properties of PLA/SF composites were simultaneously reinforced and toughened via addition of ADR oligomer. The interfacial interaction and structure-properties relationship of composites are key points of this study.

The literature analysis did not indicate any studies on fluorination tests of carbon nanocomposite coatings doped with transition metals of the nc-MeC/a-C type. This was the motivation for undertaking research in this area. As a model coating to investigate the effect of fluorination in a tetrafluoromethane (CF4) atmosphere, a nano-composite carbon coating doped with chromium nc-CrC/a-C produced by magnetron sputtering from graphite targets and the use of a Pulse-DC type medium frequency power supply was chosen [6]. After deposition of the gradient CrCN adhesive sublayer, fluorination of the main coating was conducted in a reactive mode in an (Ar+CF4) atmosphere at various CF4 contents. It was observed that the presence of CF4 in the atmosphere resulted in a reduced amount of chromium carbides formed in favor of chromium fluorides. So far, this is an observation that seems unnoticed by the carbon coatings researchers. Fluorine was assumed to bond much more readily to carbon than to chromium, due to the stability of tetrafluoromethane (CF4). The opposite seems to be true. The mechanical properties (nano-hardness and Young's modulus) and tribological properties in the 'pin-on-disc' friction pair are presented, along with the analysis of bonds occurring between chromium, carbon, and fluorine (XPS).

This study explored the effects of cryogenic treatment on the microstructure, hardness, and wear-resistance of diamond-like carbon (DLC) by cryogenically treating NAK 80 mold steel coated with DLC. Raman spectroscopy analyzed the structure of the DLC film. Nanoindenter analyzed the hardness and Young’s modulus of the film, and their relationship determined the wear resistance. Wear test assessed the wear rate and friction coefficient of the DLC film. The results showed that cryogenic treatment increased the rate of carbide precipitation and refined the grain structure. Raman spectroscopy indicated that the Raman intensity rate (I_D/I_G) of treated DLC films was smaller than those without cryogenic treatment. When the sp3 bond increased, the hardness and wear-resistance of the DLC film also increased.

3D printing with cement-based materials is a promising manufacturing technique for civil engineering applications that already allows for the design and the construction of complex and highly customized structures using a layer-by-layer deposition approach. Usually, in this type of additive manufacturing, a mixture of cement, water, aggregate and additives is extruded through a specific print head and deposited in successive layers to form the desired shape. The extrusion mechanism is one of the most expensive parts of the 3D printer. Also, for low scale 3D printers, based on the shape of the extruder and the geometry limitation of the mixing blade, the 3D mixture is often limited to a narrow range of materials due to the risk of layer splitting or blockage. Therefore, there is a need to develop affordable and feasible alternatives to the current design-fabrication-application approach of 3D printers. In this paper, various new designed mixtures of fiber reinforced mortars that can be 3D printed using only a commercially available screw pump are analyzed based on their fresh properties and mechanical characteristics. The reduced facility requirements in this approach allow 3D-printing to be more available for civil engineering applications. With further innovation in the future, this method and mixtures can be extended for sustainable and economically feasible printing of single-family housing units.

In this study, nanostructured cerium-doped TiO2 (Ce-TiO2) films with the addition of different amounts of cerium (0.00, 0.08, 0.40, 0.80, 2.40, and 4.10 wt. %) were deposited on a borosilicate glass substrate, by flow coating sol-gel process. After flow coating, deposited films were dried at the temperature of 100 °C for 1 h, followed by calcination at the temperature of 450 °C for 2 h. For the characterization of sol-gel TiO2 films, the following analytic techniques were used: X-ray diffraction (XRD), thermal gravimetry (TG), differential thermal analysis (DTA), and differential scanning calorimetry (DSC). Sol-gel derived Ce-TiO2 films were used for photocatalytic degrada-tion of the ciprofloxacin (CIP). The influence of the amount of Ce in TiO2 films, the duration of the photocatalytic decomposition, and the irradiation type (UV-A and simulated solar light) on the CIP degradation were monitored. Kinetics parameters (reaction kinetics constants and the half-life) of the CIP degradation, as well as photocatalytic degradation efficiency, were determined. The best photocatalytic activity was achieved by the TiO2 film doped with 0.08 wt.% Ce, under both UV-A, and solar irradiation.

The purpose of this study was to conduct a meta-analysis that shows the influence of fiber on ultimate compressive strength and tensile strength of ultra-high performance concrete. The internet scholarly search engines and ScienceDirect article references were used to illustrate the papers concerning the experimental investigations of mechanical properties of ultra-high strength concrete with and without fiber with clearly, completely and comparative raw data. The normal concrete test results were dismissed from this search. Seven trials were identified based on the adopted inclusion and exclusion criteria above. The meta-analysis based on standardized mean difference was carried out on the basis of a fixed-effects model for the major outcomes of the ultimate compressive and tensile properties of ultra-high performance concrete. A total of 888 test specimens were enrolled in these seven trials. The combined analysis yielded a sign of a significant improvement in ultimate compressive strength and tensile strength of ultra-high strength concrete with fiber addition of 2% by concrete volume. The summary effect size of ultimate compressive strength was 2.34 while a more improvement in term of tensile strength with effect size of 2.64. By addition fiber of 2% provides a significant benefit in mechanical properties of ultra-high performance concrete.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

Steel fibers (SF) and polyolefin (PF) are widely used for shotcrete, especially in tunnelling. Both SF and PF and have shown to meet the standards in order to reduce or substitute the conventional steel mesh as reinforcement of concrete showing mechanical and productive advantages. This study sought the analysis and assessment of the mechanical properties of fiber reinforced shotcrete, comparing in-situ with laboratory results. This was performed with low and high fiber dosages of SF and PF as well as a combination of them (hybrid mixtures). A total of seven mixtures, two of steel, two of polyolefins, two hybrids and a control mixture were manufactured at laboratory and in situ. By performing tests according to EN 14651 and slabs according to EN 14488-5, it was possible to characterize the residual flexural strengths (fRj), and energy absorption capacity (E25mm) in slabs. In addition, a fracture surface analysis was performed, and the orientation factor was obtained. This allowed the authors to quantify the loss of residual strength on site and correlate it with the fiber content and positioning. Moreover, some relationships between beam and slab tests were found, allowing to correlate the most relevant type of tests in the field of fiber reinforced concrete.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

The cast grains of the 7055 aluminum alloy were refined by adding Sm + Er, and the proper heat treatment procedure was utilized to further precipitate the rare earth phase in order to increase the alloy's strength and toughness. The grain size, microstructure and phase were characterized by optical microscopes (OM), Scanning electron microscopy - energy spectrum (SEM-EDS), XRD diffractometer (XRD). The macroscopic hardness, yield strength and tensile strength of alloy materials were measured by hardness meter and universal electronic tensile machine. The results shown that the as-cast sample and the heat treatment sample all exist Al10Cu7Sm2 and Al8Cu4Er rare earth phase; But after heat treatment, the volume percentage of the rare earth phase dramatically increased and the dispersion was more unified. When 0.3wt.%Sm and 0.1wt.%Er were added, the grain size could be refined to 53μm. With the increase of the total content of rare earth elements, the refining effect first increased and then decreased. Under 410 oC solid solution for 2h + 150oC aging for 12h, the macroscopic hardness, yield strength, tensile strength and elongation of 0.3wt.%Sm + 0.1wt.%Er+7055 as-cast sample were 155.8HV, 620.5Mpa, 658.1Mpa, and 11.90%, respectively.

The present study drops the line for the flow characteristics of fly ash-based (FA) geopolymers reinforced with polypropylene (PP) fibers undergoing the extrusion process during three-dimensional printing. Applying to the Herschel-Bulkley rheological model the research is ready with the sound theoretical basis which is used to understand the flow behavior of these materials under various conditions. A combination of experimental and numerical techniques that are based on the Finite Element Method (FEM) in COMSOL has been used in this study. The results of both the experimental and simulation approaches are then compared and the behavior of the material during extrusion is then examined. The experimental results proved PP fiber content has significant effects on rheological properties. The experiments on mixes which are either devoid of fibers or possess a high content of fiber, encountered problems like a high static yield stress and material segregation. Mixes with fibers of moderate content showed smoother extrusion processes, which means that a suitable range of fiber addition exists for the fibers that optimally balance the mechanical properties and extrudability. Numerical simulations typically agreed with experimental data for fiber contents up until it reached a certain level but not above, suggesting the existence of more complex interactions inside the fibers and the necessity for the subsequent model refinements. The investigation outlines a 0.25% and 0.5% fiber content range that leads to enhanced performance without bringing the extrusion process to greater complications and further making the production of proper, architecturally printed structures possible.

Hybrid woven kenaf-carbon composite were fabricated in this study using epoxy resin as matrix. Effects of different fabric material namely weave designs (plain and satin) and fabric counts (5×5 and 6×6) on the properties of laminated woven kenaf polymer composite were evaluated. This study evaluates the mechanical and morphological properties of hybrid fabric kenaf-carbon from kenaf yarn of 500tex. Kenaf and carbon fabrics were used in this work, where vacuum infusion technique was selected to prepare the composite and epoxy resin was used as a matrix. The fibre weight content is 30% and four specimens were prepared for each samples and tested for their tensile, flexural, and impact strengths. The morphological properties of composites were analysed through the scanning electron microscope (SEM). The results revealed that plain woven fabric is favourable in terms of tensile and impact strengths compared to satin woven fabric. Meanwhile, 5×5 of fabric count gives better flexural modulus than composite fabricated with 6×6 fabric count. The morphologies of the fractured surface investigated by SEM demonstrated better adhesion properties and less fibre pull-out on plain woven fabric.

Although 7055 aluminum alloy is a deformed aluminum alloy and will show excellent mechanical properties after recrystallization after large deformation, it is a method to enrich its application range if rare earth is added and the rare earth phase dispersion is promoted by heat treatment. This article used optical microscopy, scanning electron microscopy energy dispersive spectroscopy (SEM-EDS), X-ray diffraction (XRD), micro Vickers hardness and room temperature stretching methods to study the as-cast 7055-xEr (x=0wt.%, 0.2wt.%, 0.4wt.%, 0.6wt.%, 0.8wt.%) aluminum alloy after being subjected to 460 oC×3h homogenization and 410 oC×1h solid solution+150 oC×12h aging treatment the changes in microstructure and properties. The results indicated that: when 0.2wt.%Er was added to 7055 aluminum alloy after solution at 410 oC×1h and aging at 150 oC×12h, the dendrite structure was significantly reduced, the grain thinning was obvious and the distribution was uniform, Al8Cu4Er phase appeared in the lamellar eutectic η-Mg(Zn,Al,Cu)2 structure at grain boundaries, and the hardness reached 168.8HV. The yield strength, tensile strength and elongation were 542.12Mpa, 577.67MPa and 8.36%, respectively.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

Five years ago, the concept of addressed fiber Bragg structures (AFBS) was proposed, which simultaneously perform the functions of a two-frequency radiation shaper, the difference frequency of which is the AFBS address, and a sensitive element, since the value of the difference frequency is invariant to measured physical fields, and the set of difference frequencies, moreover, is orthogonal in the array of such sensors, enabling their address multiplexing. In this article, we provide an overview of the theory and technology of AFBS, including the structures with three or more spectral components with various combinations of difference frequencies, symmetrical and asymmetric, performing the functions of the address and converting information signals to the low-frequency range at the same time, along with other functions. The subjects of interrogation of these structures, their fabrication and calibration are discussed as well. We also consider a wide range of applications in which AFBS can be used, covering such areas as oil and gas production, power engineering, transport, medicine, etc. In addition, the prospects of AFBS further development are proposed.

In the recent years, tubular nanostructures have been related with immense advances in various fields of science and technology. Considerable research efforts have been centered on the theoretical prediction and manufacturing of non-carbon nanotubes (NTs), which meet modern requirements for the developing of novel devices and systems. In this context, diatomic inorganic nanotubes formed by atoms of elements from the 13th group of the periodic table (B, Al, Ga, In, Tl) and nitrogen (N), have received much research attention. In the present work, the elastic properties of single-walled boron nitride, aluminium nitride, gallium nitride, indium nitride and thallium nitride nanotubes were numerically evaluated using the nanoscale continuum modelling approach (also called molecular structural mechanics). The elastic properties (rigidities, surface Young´s and shear moduli, and Poisson´s ratio) of nitride nanotubes are discussed with respect to the bond length of the corresponding diatomic hexagonal lattice. The results obtained contribute to a better understanding of the mechanical response of nitride compound-based nanotubes, covering a broad range from the well-studied boron nitride NTs to the hypothetical thallium nitride NTs.

Membrane gas absorption technology and solar-assisted regeneration system are two promising approaches to reduce high energy consumption associated with carbon dioxide capture from coal fired power plants. In the present study, a solar-assisted hollow fiber membrane contactor (SOL-HFMC) power plant is proposed to capture and desorb CO₂ in hollow fiber membrane contactors with the assistance of solar thermal collectors. Techno-economic assessment and sensitivity analysis of the proposed system is carried out in three studied locations with different weather conditions for a 580 MWe pulverized coal power plant. Research results show that, the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless whether TES system is applied or not. In addition, CEI of the SOL-HFMC power plant with TES system is 4.36 kg CO₂/MWh, 4.45 kg CO₂/MWh and 4.66 kg CO₂/MWh lower than that of the reference power plant. The prices of membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for SOL-HFMC power plant with TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m² for Jinan, 95.20 $/m² for Xining, and 128.70 $/m² for Lhasa, respectively. To be more competitive than solar-assisted ammonia-based post-combustion CO₂ capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. The findings can provide guidance for decision-making and risk management strategies.

Composite fiber materials are superior materials due to their high strength and light weight. Composites reflect the properties of their constituents, which is proportional to the volume fraction of each phase. There are different fiber reinforcement types and each affects it’s flexural, tensile and compression strength. When selecting a composite for a specific application, the forces excreted on the composite must be known in order to determine the reinforcement type. Unidirectional fiber reinforcement will allow very strong load resistance but only in one direction where as a random orientated fiber reinforcement can resist less load but can maintain this quota in all directions. These materials are said to be anisotropic. Certain composite fibers, taking into consideration there weights, are physically stronger than conventional metals. This research deals with the analysis of three composite materials with different reinforcement types, volume fraction and phase content. It was found that material A (glass epoxy) was the strongest in the longitudinal direction with a flexural strength of 534 MPa in the longitudinal and 420 MPa in the transverse direction. The flexural stresses of material B (glass silicone) and material C (glass polyester) where both found in the 120 to 135 MPa range. Differences were due to their differences in matrix composition and reinforcement type.

The awareness of the vulnerability of existing structures under both seismic and energy viewpoints highlight the need to develop integrated retrofit solutions combining the structural and thermal performances. In this perspective, the study explores the efficacy of the Resisto 5.9 Tube system, a seismic coat that improves the seismic behaviour of masonry and reinforced concrete (RC) structures, also enhancing their energy performances, thanks to the thermal coat integrated in the basic steel system. The research involves the application of a design procedure specifically developed for this retrofit system from the seismic perspective. Once all the system elements are designed, non-linear static analyses are performed with a Finite Element software comparing the building’s seismic performances before and after the application of Resisto 5.9 Tube. The results demonstrate a significant increase in seismic safety coefficient, proving that this intervention type can be useful to obtain the seismic upgrading of existing RC buildings.

This study investigates the process of multi-walled carbon nanotube (MWCNT) coatings to enhance the lamp heating temperature for solar thermal absorption applications. The primary focus is studying the effects of self-organized honeycomb structures of CNTs formed on silicon substrates on different cell area ratios (CAR). The drop-casting process developed honeycomb-structured MWCNT-coated absorbers with varying CAR values ranging from ~ 60% to 17%. The optical properties were investigated within the visible (400-800 nm) and near-infrared (934-1651nm) wavelength ranges. Although fully coated MWCNT absorbers showed the lowest reflectance, honeycomb structures with a ~ 17% CAR achieved high-temperature absorption. These structures maintained 8.4% reflectance at 550 nm while dramatically increasing infrared reflection to 80.5% at 1321 nm. The performance of solar thermal was assessed throughout a range of irradiance intensities, from 0.04 W/cm² to 0.39 W/cm². The honeycomb structure with a ~17% CAR value consistently performed better than other structures by reaching the highest absorption temperatures (ranging from 52.5°C to 285.5°C) across all measured intensities. A direct correlation was observed between the reflection ratio (visible: 550 nm / infrared: 1321 nm) and temperature absorption efficiency, where lower reflection ratios were associated with higher temperature absorption. This study highlights the significant potential for the large-scale production of cost-effective solar thermal absorbers through the application of optimized honeycomb-structured absorbers coated with MWCNTs. These contributions enhance solar energy efficiency for applications in water heating and purification, thereby promoting sustainable development.

This research examines the fire resistance of geopolymer composites (GCs), formulated using alka-li-activated metakaolin and aluminum powder. The production method involves spray-coating carbon steel plates with fresh GCs, followed by a 28-day curing period at room temperature. Sub-sequently, fire performance and aging tests are conducted to evaluate fire resistance. The study investigates GC properties, including apparent density, bending strength, compression strength, thermal conductivity, porosity, and production cost. Morphological changes before and after fire and aging tests are analyzed using scanning electron microscopy (SEM). Results demonstrate GC foams' outstanding thermal insulation, providing up to 75 minutes of fire resistance with a 6 mm coating, reducing temperatures by 300 °C compared to uncoated steel. GCs exhibit a density of 670 kg/m³, thermal conductivity of 0.166 W/m·K, 68% porosity, and cost efficiency at 250 dollars per cubic meter. This study underscores the potential of foamed geopolymer coatings for effective and economical surface protection.

A special vibration damper is proposed for material property identification through a scratching process on a vibrating object. This paper presents the design and working principle of a scratching damper based on a scratch test device. A non-contact electromagnetic shaker is used to generate the shaking force for the vibration of the tested object. The required pressure on the scratched material during the scratching process is generated by a compression spring and adjusted by changing the amount of compression of the spring. The proposed damper is designed and tested on extruded aluminum samples for the determination of its Young’s modulus and hardness and validated by using the standard test instruments. Observations of physical dimensions of the scratching tracks are determined by microscope and were utilized to compute the scratching energy factor. Load curves are obtained at different pressure of the scratching process. The hysteresis loop energy during the scratching process of the tested object is measured and used for the determination of material properties of the object. Furthermore, energy conservation law, scratch energy release rate and loop energy release rate are used to determine the Young’s modulus and hardness of the sample. The measurement accuracy of the modulus and hardness of the tested sample is evaluated. The proposed method of material testing has several advantages over the traditional methods such as low cost and high repeatability, and may be used as an alternative to the standard modulus and hardness testers.

Micro channel tube (MCT) is widely employed in industry due to its excellent efficiency in heat transfer. An MCT is commonly produced through extrusion within a porthole die, where severe plastic deformation is inevitably involved. Moreover, the plastic deformation, which dramatically affects the final property of the MCT, varies significantly from location to location. In order to understand the development of the microstructure and its effect on the final property of the MCT, the viscoplastic self-consistent (VPSC) model, together with the finite element analysis and the flow line model, is employed in the current study. The flow line model is used to reproduce the local velocity gradient within the complex porthole die, while VPSC model is employed to predict the evolution of the microstructure accordingly. In addition, electron backscatter diffraction (EBSD) measurement and mechanical tests are used to characterize the evolution of the microstructure and the property of the MCT. The simulation results agree well with the corresponding experimental ones. The influence of the material’s flow line on the evolution of the orientation and morphology of the grains, and the property of the produced MCT are discussed in detail.

Lap joints were friction stir welded in AA 7075-T6 at 1320 rpm and using two welding speeds: 70 mm/min and 120 mm/min. The temperature profiles of the weld zone were registered during the process; furthermore, the microhardness, tensile strength, and microstructure of the joints produced were examined. This study brings new insights into the thermomechanical behavior of the material during the process. The peak temperature obtained with the lower welding speed (70 mm/min) is 10% higher than that obtained with the higher speed (120 mm/min). Moreover, a 5% increase in microhardness and a 6% increase in tensile strength were were observed increasing the welding speed. Addition-ally, the microstructure examination demonstrated that, by decreasing the welding speed, the larger interaction between the tool and the material results in a deeper stir zone due to the increased heat diffusion downwards to the material. This heat flow affects the thermal profile and influences the resulting mechanical properties of the welded joints.

A comprehensive modeling framework for the thermoforming of polymer matrix woven laminate composite was developed. Two numerical indicators, the slip path length and traction magnitude, have been identified to be positively correlated to matrix smearing and wrinkling defects. The material model has been calibrated with picture-frame experimental results, and the prediction accuracy for intra-ply shear and thickness distribution were examined with measurements on the physically formed parts. Finally, a parametric study was conducted to determine the relationship between various process parameters and the quality of the formed part. For the trapezoidal part, orienting the laminate at 45-degrees to the mold axis reduces the likelihood of matrix smear and wrinkling defects. Although this laminate orientation yielded a greater spatial variation of part thickness, the thickness deviation is lower than that for the 0-degree orientation case. Higher forming rates were found to result in more defects due to increased slip path lengths and traction magnitudes. Optimal forming speeds should balance rapid shaping within the operating temperature window while avoiding tear. It was discovered that shallower molds benefit from faster ramp rates, while deeper molds require slower rates to manage extensive shearing, stretching, and bending. Faster forming rates lead to smaller thickness increases at high intra-ply shear regions, indicating a shift from intra-ply shear to out-of-plane bending due to the visco-plastic effect of the molten laminate, and can negatively impact part quality. Lastly, it was shown that a well-conceived strategy using darts could improve the part quality by reducing the magnitude of the defect indicators.

Concrete being one of the most frequently used construction materials in the field of construction. The use of concrete has increased with the passage of time as the more and more construction activities are taking place around the globe. Different materials have been added in to the concrete mix to provide the concrete more strength and make it more durable and long lasting. This paper looks into a detailed comparison of concrete strength when casted with in the presence of carbon fibers, steel fibers and glass fibers. The compressive strength for cubes and cylinder with carbon fibers is the highest as compare to steel fibers as well as glass fibers. The compressive strength of concrete is measured on 3 day, 7 day, 14 day and 28 day strength. The compressive strength of cube on 28th day strength is 37.52 MPa for carbon fiber steel, for steel fiber it is 34.22 MPa and with glass fiber the strength is 29.335 MPa whereas the compressive strength of cylinder with carbon fibers the 34.88 MPa, with steel fiber it is 34.22 MPa and with glass fiber the strength is 27.447 MPa. For the cubes the maximum difference between different fibers inducted concrete sample is 28% approximately and for cylinder it is 27%, respectively. On the other hand, the tensile strength of concrete was also gained with the carbon fiber. It was determined that carbon fiber provided about 16% and 12.8% tensile strength higher than glass and steel fibers respectively.

In this paper, the effect of preheating on the mechanical properties and micro structure of similar friction stir welded AA6061 aluminum alloys sheets was investigated. Aluminum alloy 6061 sheets with a thickness of 5 mm and threaded cylindrical pins were used. Rotation and traverse speeds were 1200 rpm and 75 mm/min, respectively. The results of tensile tests performed on the welded samples showed that compared to the non-preheated samples, preheating had increased the strength and elongation of the joints by 58% and 46%, respectively. In the present study, during the welding process preheating cause emerged heat with lower slope from stir zone. This phenomenon may result in Increase the deformation resistance of material and consequently decrease of grain size. This grain refinement can improve the mechanical properties of welds. Accordingly, hardness and strength of the material will be increased.

In this article, bio-composites derived from starch-glycerol biodegradable matrix reinforced with jute fibers have been fabricated using the wet hand lay-up and compression moulding techniques. Samples having different weight percentages of jute fiber in the starch matrix have been analysed. The fibers surface was chemically treated by alkaline sodium hydroxide for improving the interphase bonding between fiber and matrix. Tensile test for the composites were done and the sample with highest tensile strength was selected for further tests that included water absorption, scanning electron microscopy and thermal analysis. It has been concluded that the ultimate tensile strength was found to be maximum for the composition of 15% fiber by weight composite as 7.547 MPa without epoxy coating and 10.43 MPa with epoxy coating. The major disadvantage of bio-composite is its high water absorption property, which in this study has been inhibited by the epoxy resin layer. Herein, the results of various tests done disclose a noteworthy improvement in the overall properties of bio-composite, in comparison to the neat biodegradable starch matrix.

In recent years, additive manufacturing of products made from 5000 series alloys has grown in popularity for marine and automotive applications. In this work, we compare of mechanical properties characteristics of aluminum alloy 5056 material produced by wire-arc additive technology and rolling. We carried out tension tests under quasi-static loading and impact toughness tests under impact loading. The results show that upon similar ultimate tensile strength and ductility, material after additive manufacturing demonstrates decreased resistance against dynamic loading than material manufactured by the typical method of casting and rolling. This decrease in properties was explained through macro- and microstructure analysis.

Due to the manufacturing process of Additive Manufacturing (AM) Parts the mechanical properties cannot be predicted. The scope of the present work is to propose a predictive tool for the mechanical properties of AM parts through the use of Adaptive Neuro-Fuzzy Inference System (ANFIS). The Adaptive Neuro-Fuzzy Inference System (ANFIS) combines neural networks with fuzzy logic to generate a mapping between the inputs and the output. Real data experiments from different AM technologies and materials compose the initial dataset so a detailed investigation is conducted to gain knowledge of how different parameters affect the UTS, the elongation and the Young modulus of each experiment. Experimental data were also use to train, check and verify the methodology. The method is tested for FFF technology, PLA material and 3 point bending stress, with interesting results.

The article offers a comprehensive overview of recent breakthroughs in eco-friendly polymers and polymer composites, underscoring their pivotal role in addressing sustainability challenges across diverse industrial sectors. Despite encountering obstacles related to performance and processability, biopolymers sourced from renewable materials emerge as promising alternatives for the plastics that are currently used by human beings. Natural fillers are highlighted as a strategic avenue for crafting sustainable composites, with residual natural fillers being particularly explored. Heightened environmental concerns propel discussions on the criticality of integrating biodegradable materials with natural fillers, underlining the urgency for clear frameworks and financial incentives to support adoption of these materials. Additionally, the article examines the potential of biodegradable polymers and polymer composites, with a specific emphasis on the utilization of polyhydroxyalkanoate (PHA) in composite materials and its market prospects. Moreover, it emphasizes the indispensable need for ongoing research and development endeavors to address environmental challenges within the polymer sector, reflecting a mounting interest in sustainable materials across industries.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

During carbonation process, the presence of water is an important parameter to accelerate this phenomenon. The carbon dioxide (CO₂) has been used as curing process production of fiber cement boards keeping the dimensional stability of cellulose fibers in cementitious matrix and promoting the CO₂ capture of environment. In addition, magnesium oxysulfate (MOS) cement has been used as another alternative binder to reduce the amount of CO₂ in the nature. The aim of this scientific paper is analysis the effect of rehydration method on the physical-mechanical properties of CO2-cured magnesium-based fiber cement boards. These boards were produced by Hatschek process simulation. The physical-mechanical performance and microstructural characteristics of MOS boards before and after carbonation were investigated by: water absorption (WA), apparent porosity (AP), and bulk density (BD); four-point bending test; X-ray diffraction (XRD); thermogravimetric analysis (TGA) and scanning electron microscopy (SEM). According to the results, it was possible observe which the accelerated carbonation process resulted in improvements in the mechanical properties of the boards. The boards carbonated after 48 hours showed higher Modulus of Rupture values. The rehydration process of the composites before carbonation led to enhancements in the boards pre-cured for 48 and 72 hours, demonstrating that carbonation occurred more effectively after the supply of water through rehydration. The improvements in mechanical properties were associated with the formation of hydration products, which preferentially formed in the pores and voids of the fiber-cement. The presence of these carbonation products altered the physical properties of the materials, increasing the density of the boards and reducing the void volume. The decomposition of the formed carbonates was confirmed by thermogravimetric analysis, which indicated that the rehydration process favored the carbonation of the materials

The improvement of mechanical properties of cantala fiber and its composites. Treatments including alkali, silane, and the combination of both were carried out to modify the fiber surface. The influence of chemical treatments on fiber properties such as the degree of crystallinity and tensile strength was investigated. A variety of short cantala fiber reinforced rHDPE composites were produced by hot press, and the effect of fiber treatment on the flexural strength of composites was observed. SEM observations also carried out to highlight these changes. The result shows that alkali treatment improves tensile strength and tensile modulus of alkali treated fiber (NF12) which was predicted as a result of the enhancement of the cellulose crystallinity. In contrast, the tensile strength and tensile modulus of silane (SF05) and alkali-silane treated fiber (NSF05) decreased compared to untreated fiber (UF) which is caused by the addition of amorphous material. The tensile strength of alkali-silane treated fiber (NSF05) was lower than alkali treated fiber (NF12), but the composites prepared with NSF05 showed the highest increment of flexural strength of 25.9%. This may be due the combination of alkali and silane treatment helped in the better formation of fiber-matrix interface adhesion.

Luminescent carbon dots (CDs) were locally synthesized in the core of CYTOP fibers using IR femtosecond laser direct writing (FLDW), a one-step simple method serving as a post-treatment of the genuine fiber. This approach enables the creation of several types of modifications such as ellipsoid voids. The CDs and photoluminescence (PL) distribute at the periphery of the voids. The PL spectral properties were studied through Excitation Emission Matrix in the visible range and excitation/emission spectrum in UV/visible range. Our finding reveals the presence of at least 3 distinct luminescent species, facilitating a broad excitation range extending from UV to green, and light emission spanning from blue to red. The average laser power and dose influence the quantity and ratio of these luminescent CD species. Additionally, we measured the spatially resolved lifetime of the luminescence during and after the irradiation. We found longer lifetimes at the periphery of the laser-induced modified regions and shorter ones closer to the center, with a dominant lifetime ~ 2ns. Notably, unlike many other luminophores, these laser-induced CDs are insensitive to oxygen, enhancing their potential for display or data storage applications.

This study presents an innovative approach for the utilization of industrial by-products and municipal waste in the production of sustainable and environmentally friendly cement mortar. We explored stabilized stainless-steel reduced slag (SSRS) and polyethylene (PE) plastic waste as partial replacements for aggregates. Various engineering properties of the resulting cement mortar specimens, including slump, slump flow, compressive strength, flexural strength, tensile strength, water absorption, and ultrasonic pulse velocity (UPV), were investigated through comprehensive experimental tests. The influence of different water-cement (w/c) ratios and substitution amounts on the engineering properties of the cement mortar samples was thoroughly examined. The findings revealed that an increase in PE substitution adversely affected the overall workability of the cement mortar mixtures, whereas an increase in SSRS amount contributed to enhanced workability. As for the hardened properties, a consistent trend was observed for both cases, with higher w/c ratios and substitution amounts leading to reduced mechanical properties. Water absorption and UPV test results validated the increased formation of porosity with higher w/c ratios and substitution amounts. This study proposes a promising method to effectively repurpose industrial by-products and municipal wastes, transforming them into sustainable construction and building materials. Additionally, a comparative analysis of transportation costs and carbon footprint emissions between SSRS-cement mortar and PE-cement mortar was conducted to assess their environmental impact and sustainability. Generally, higher w/c ratios and replacement levels corresponded to reduced carbon footprint. The geographical location of the source of SSRS and PE remains a challenge and studies to overcome this challenge must be further explored.

This study explores the impact of carbon fiber length and content on the rheological properties and performance of coatings used in lost foam casting. The investigation encompassed fiber lengths of 1 mm, 3 mm, and 6 mm, and fiber contents of 0.2%, 0.5%, and 0.8%. The effects on coating viscosity, shear stress, coating weight, and surface morphology were meticulously evaluated. The results demonstrate that incorporating carbon fibers significantly enhances coating viscosity and shear stress compared to fiber-free coatings, with more pronounced effects observed at higher fiber contents and longer fiber lengths. Nevertheless, excessive fiber content and length can lead to agglomeration, negatively impacting coating uniformity. Optimal fiber length and content were identified, striking a balance between improved rheological properties and coating performance. These findings provide critical insights for the development and industrial application of high-performance coatings in lost foam casting.

Livestock farming plays a crucial role in agriculture and is important in meeting people's needs for a better life in the new era. However, due to China's "double carbon" target, the development of animal husbandry has been affected by the level of carbon emissions. To study the spatial dis-tribution and dynamic evolution of livestock carbon emissions in Shandong Province, we used panel data from 16 prefecture-level cities in Shandong Province from 2001 to 2022 to determine the spatial differentiation of livestock carbon emissions in Shandong Province and their dynamic evolution by combining spatial and non-parametric estimation methods based on livestock carbon emissions and livestock emission intensity measured by city. The results of the study show that the distribution of carbon emissions from animal husbandry in Shandong Province is in a "dis-persed-aggregated" pattern, and the intensity of carbon emissions shows a gradual downward trend, with a ladder-like distribution characterized by high in the west and low in the east. Through the analysis of the dynamic evolution of nuclear density, we observe that the regional differences of animal husbandry carbon emissions in Shandong Province are expanding, showing the characteristics of polarization. The difference of carbon emissions in the peninsula is gradually narrowing, and the phenomenon of polarization is weakening. The carbon emissions of animal husbandry in the central and western regions of Shandong are polarized.

CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron（CGI） through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

Monte Carlo techniques have been extensively used for planning laser-based clinical procedures such as photobiomodulation. However, the effect of several biological tissue characteristics, including morphological structure and physiological parameters, has not been carefully addressed in many applications. Specifically, many questions remain concerning the effect of skin phototype and body mass index on the efficacy of photobiomodulation for extraoral therapies. To address these questions, a Monte Carlo simulation model was developed to analyze the effects of body mass index-dependent skin structure and Fitzpatrick skin type, specifically tailored for the morphological characteristics of cheek tissue. The model describes the settings of a typical oral photobiomodulation treatment protocol for pain relief, namely the use of 660 nm and 808 nm laser wavelengths and a therapeutic dose of 2.0 J/cm² on the masseter muscle. The simulations were used to train a machine learning predictive model aimed at accelerating the treatment planning stage and assessing the importance of patient-specific parameters. A multiple regression approach was adopted to predict muscle dose and treatment time for the effective delivered dose.

Motivated by the PEACOC project on metal recovery from solid wastes, an innovative magnetic density separation (MDS) process has been developed for granular material sorting. It has intrinsic advantages over the existing industrialized MDS by eliminating fluid turbulence and particle jamming problems. The new MDS applies an inclined planar magnet and a horizontal basin containing a static magnetic fluid as the separation medium. A particle sliding phenomenon is identified as a feature of the process which could help the separation. The MDS successfully sorted shredded PCBAs to concentrate valuable metals and sorted shredded wires to reduce metallic contaminants in the plastic fractions. A pilot scale facility is introduced to show the design to achieve continuous production and to reduce the consumption of ferrofluid.

Aluminum alloy Al 2024-T3 were successfully joined using friction stir spot jwelding joining (FSSW). Satisfactory joint strengths were obtained at different welding parameters (tool rotational speed, tool plunge depth, dwell time) and tool pin profile (straight cylindrical, triangular and tapered cylindrical). Resulting joints were welded with welded zone. The different tools significantly influenced the evolution on the stir zone in the welds. Lap-shear tests were carried out to find the weld strength. Weld cross section appearance observations were also done. The macrostructure shows that the welding parameters have a determinant effect on the weld strength (x: the nugget thickness, y: the thickness of the upper sheet and SZ: stir zone). The main fracture mode was pull out fracture modes in the tensile shear test of joints. The results of tensile shear tests showed that the tensile-shear load increased with increasing rotational speed in the shoulder penetration depth of 0.2 mm. Failure joints were obrerved in the weld high shoulder penetration depth and insufficient tool rotation.

Lake sediment records are of great importance for understanding the evolution of watershed environments. Various studies have been carried out to constrain the depositional ages of lake sediments and examine their physical, chemical, and biological characteristics, aiming to construct historical vegetation, environment and climate patterns in Chinese lake watersheds. In this study, we obtained relevant literature on lake sediment records by searching the key word 'age-depth' from the databases – Web of Science and China National Knowledge Infrastructure (CNKI, the largest Chinese academic database). We analyzed the literature based on its type (published in a Chinese/English journal or as a Master’s/PhD thesis), period of publication, journal (if published in a journal), key authors, study area, dating scale, and main aims. The results suggest that the lakes in the plateau regions are the most popular research topic typically covering 100–200 years (short-term) and 500–30,000 years (long-term). The literature focuses on a wide range of topics, from past environmental evolution in the watershed to lake ecology, and provides a solid foundation for better understanding regional climate change and the preservation of lake environments and ecosystems. In the future, resulting data from environmental reconstruction with lake sediments will be needed to integrate with emerging information processing technologies (e.g., artificial intelligence and meta-analysis), to disentangle the complex interplay between Earth surface processes and global climate change; furthermore, strengthening interdisciplinary collaboration will deepen our comprehension of man-land relationship and promote the sustainable management of lake ecosystems in the context of global climate change.

Interest grows in designing silicon-on-insulator slot waveguides to trap optical fields in subwavelength-scale slots and developing their optofluidic devices. However, it is worth noting that the inherent limitations of the waveguide structures may result in high optical losses and short optical paths, which challenge the device performance in optofluidics. Incorporating the planar silicon-based slot waveguide concept into a silica-based hollow-core fiber can provide a perfect solution to realize an efficient optofluidic waveguide. Here we propose a subwavelength-scale liquid-core hybrid fiber (LCHF), where the core is filled with carbon disulfide and surrounded by a silicon ring in a silica background. The waveguide properties and the Stimulated Raman Scattering (SRS) effect in the LCHF are investigated. The fraction of power inside the core of 56.3% allows an improved sensitivity in optical sensing; while the modal Raman gain of 23.60 m-1·W-1 is 2 times larger than that generated around a nano fiber with the interaction between the evanescent optical field and the surrounding Raman media benzene-methanol, which enables a significant low-threshold SRS effect. Besides, this in-fiber structure features compactness, robustness, flexibility, ease of implementation in both trace sample consumption and reasonable liquid filling duration, as well as compatibility with optical fiber systems. The detailed analyses of the properties and utilizations of the LCHF suggest a promising in-fiber optofluidic platform, which provides a novel insight into optofluidic devices, optical sensing, nonlinear optics, etc.

Amidst escalating environmental concerns, short natural fiber thermoplastic (SNFT) biocomposites have emerged as sustainable materials for the eco-friendly production of mechanical components. However, their limited durability has prompted research into the experimental evaluation of the deterioration of the mechanical characteristics of SNFT biocomposites, particularly under the influence of ultraviolet rays. However, conducting tests to evaluate the mechanical properties can be time-consuming and expensive. In this study, an artificial neural network (ANN) model was employed to predict the mechanical properties (tensile strength) and the impact performance (resistance and absorbed energy) of polypropylene reinforced with 30 wt.% short flax or wood pine fibers (referred to as PP30-F or PP30-P, respectively). Eight parameters were collected from experimental studies. The ANN input parameters comprised nondestructive test results, including mass, hardness, roughness, and natural frequencies, while the output parameters were the tensile strength, the maximum impact load and absorbed energy. The model was developed using the ANN toolbox in MATLAB. The linear coefficient of correlation and mean squared error were selected as the metrics for evaluating the performance function and accuracy of the ANN model. They calculate the relationship and the average squared difference between the predicted and actual values. The data analysis conducted by the models demonstrated exceptional predictive capability, achieving an accuracy rate exceeding 96%, which was deemed satisfactory. For both the PP30-F and PP30-P biocomposites, the ANN predictions deviated from the experimental data by 3, 5, and 6% about the impact load, absorbed energy, and tensile strength, respectively.

This review contains a popular presentation of the history of carbon nanostructure discovery, a short description of the main approaches to production and investigation of such objects and consideration of the most perspective ways of their applied usage.

Existence of carcinogenic nitrite in food has attracted much attention, however, it is still a challenge to develop nitrite sensor with higher sensitivity and selectivity to enlarge its applications in daily life. Herein, one-dimensional honeycomb-like carbon nanofibers (HCNFs) were synthesized with an electrospun technology, and its specific structure enables the controlling growth and highly dispersed bismuth nanoparticles (Bi NPs) on its surface, which endows the obtained Bi/HCNFs with excellent electrocatalytic activity toward nitrite oxidation. By modifying Bi/HCNFs on screen-printed electrode, the constructed Bi/HCNFs electrode (Bi/HCNFs-SPE) can be used for nitrite detection in one drop of solution, and exhibits higher sensitivity (1269.9 μA mM-1 cm-2) in a wide range of 0.1~800 μM with lower detection limit (19 nM). Impressively, the Bi/HCNFs-SPE has been successfully used for nitrite detection in food and environment samples, the satisfactory property and recovery indicates its feasibility in further practical applications.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

The distributed long-range sensing system using the standard telecommunication single-mode optical fiber in a function of a distributed sensor for sensing of mechanical vibrations is described. Various events generating vibrations such as walking or running person, moving cars, trains and others can be detected, localized and classified. The sensor and related sensing system components were designed and constructed and the system was tested both in the laboratory and in the real situation with 88 km telecom optical link, and the results are presented.

Asymmetric lithium salts, such as Lithium (difluoromethanesulfonyl)(trifluoromethanesulfonyl)imide (LiDFTFSI), have been demonstrated to surpass traditional symmetric lithium salts with improved Li+ conductivity and the capacity to generate stable solid electrolyte interphase (SEI) while maintaining compatibility with aluminum (Al0) current collector. However, the intrinsic reductive mechanism through which LiDFTFSI influences battery performance remains unclear and under debate. Herein, the detailed SEI reactions of LiDFTFSI-based electrolytes were investigated by combining density functional theory and molecular dynamics, aiming to clarify the formation process and atomic structure of SEI. Our results show that asymmetric DFTFSI– weakens the interaction between carbonate solvents and Li+, and substantially alter the solvation structure, exhibiting a well-balanced coordination capacity to bis(trifluoromethanesulfonyl)imide (TFSI–). Nanoseconds hybrid molecular dynamics simulation further reveals that the preferential decomposition of LiDFTFSI produces sufficient LiF and Li2O to facilitate a robust SEI. Moreover, the abundant F– generated from LiDFTFSI decomposition accumulates on the Al surface and subsequently combines with Al3+ from the current collector to form AlF3, potentially inhibiting corrosion of the current collector. Overall, these findings elucidate how LiDFTFSI regulates the solvation sheath and SEI structure, advancing the development of high-performance electrolytes compatible with current collector.

Strain induced melt activation process (SIMA) creates a globular microstructure which improves the hardness and ultimate tensile stress (UTS) of 7075 aluminum alloys. But, at the grain boundaries of SIMA processed 7075 aluminum alloy, presence of continuous and brittle intermetallic compounds and the eutectic structure result in decreasing mechanical properties, such as elongation, formability and etc. Hence, in order to improve microstructure and formability of 7075 aluminum alloy respect to SIMA process, a new process was done that is called two-step strain induced melt activation (TSSIMA). This process, which has been mentioned in the experimental procedure section, both organized globular structure and significantly modified the microstructure of the alloy compared to that of the SIMA method. It promoted discontinuity and more homogeneity in distribution of the precipitates and, approximately removed the eutectic mixture. Performing the rolling process on the alloy also revealed that it is more effective in formability enhancement in comparison with SIMA process. Also, it increased the hardness of 7075 aluminum alloy respect to that of SIMA process.

This study investigates the dynamic characteristics of Natural Rubber (NR)/Polybutadiene Rubber (PBR) based hybrid magnetorheological elastomer (MRE) sandwich composite beams through numerical simulations and finite element analysis, employing Reddy's third-order shear defor-mation theory. Four distinct hybrid MRE sandwich configurations were examined. The validity of finite element simulations was confirmed by comparing them with results from magnetorheo-logical (MR) fluid-based composites. Further, parametric analysis explored the influence of magnetic field intensity, boundary conditions, ply orientation, and core thickness on beam vi-bration responses. Results reveal a notable 10.4% enhancement in natural frequencies in SC4-based beams under a 600mT magnetic field with clamped-free boundary conditions, attributed to in-creased PBR content in MR elastomer cores. However, higher magnetic field intensities result in slight frequency decrements due to filler particle agglomeration. Additionally, augmenting magnetic field intensity and magnetorheological content under clamped-free conditions improves the loss factor by 66% to 136%, presenting promising prospects for advanced applications. This research contributes to a comprehensive understanding of dynamic behavior and performance enhancement in hybrid MRE sandwich composites, holding significant implications for engi-neering applications. Furthermore, this investigation provides valuable insights into the intricate interplay between magnetic field effects, composite architecture, and vibration response.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

Imperfection sensitivity of large amplitude vibration of curved single-walled carbon nanotubes (SWCNTs) is considered in this study. The SWCNT is modeled as a Timoshenko nano-beam and its curved shape is included as an initial geometric imperfection term in the displacement field. Geometric nonlinearities of von Kármán type and nonlocal elasticity theory of Eringen are employed to derive governing equations of motion of nano-beam. Spatial discretization of governing equations and associated boundary conditions is performed using differential quadrature (DQ) method and the corresponding nonlinear eigenvalue problem is iteratively solved. Effects of value and location of the geometric imperfection, and the nonlocal small-scale parameter on the nonlinear frequency ratio and imperfection sensitivity of a curved SWCNT for various boundary conditions are investigated. The results show that the geometric imperfection plays a significant role in the nonlinear vibration characteristics of curved SWCNTs.

This investigation explores the potential of enhancing aqueous zinc-ion batteries (AZIBs) through the introduction of a novel cathode material, NH4V4O10 (NVO), combined with reduced graphene oxide (rGO). Utilizing Density Functional Theory (DFT), it was hypothesized that the incorpora-tion of rGO would increase the interlayer spacing of NVO and diminish the charge transfer in-teractions, thus promoting enhanced diffusion of Zn2+ ions. These theoretical predictions were substantiated by experimental data acquired from hydrothermal synthesis, which indicated a marked increase in interlayer spacing. Significantly, the NVO-rGO composite exhibits remarkable cyclic durability, maintaining 95% of its initial specific capacity of 507 mAh g−1 after 600 cycles at a current density of 5 A g−1. The electrochemical performance of NVO-rGO not only surpasses that of pristine NVO but also outperforms the majority of existing vanadium oxide cathode materials reported in the literature. This study underscores the effective integration of theoretical insights and experimental validation, contributing to the advancement of high-performance energy storage technologies.

This study explores the enhancement of aqueous zinc-ion batteries (AZIBs) using ammonium-enhanced vanadium oxide cathodes. Density Functional Theory (DFT) calculations reveal that NH₄⁺ incorporation into V₆O₁₆ lattices significantly facilitates Zn²⁺ ion diffusion by reducing electrostatic interactions, acting as a structural lubricant. Subsequent experimental validation using (NH₄)₂V₆O₁₆ cathodes synthesized via a hydrothermal method corroborates the DFT findings, demonstrating remarkable electrochemical stability with a capacity retention of 90% after 2000 cycles at 5 A g⁻¹. These results underscore the potential of NH₄⁺ in improving the performance and longevity of AZIBs, providing a pathway for sustainable energy storage solutions.

A new type of low cost, environmentally friendly wood-plastic composites (WPC) containing carbon nanotubes(CNT)of low content 0%, 0.05wt%, 0.1wt% and 0.15wt%, wood fibers of 14wt% and polymer PES of 86wt% was manufactured by the selective laser sintering (SLS) approach of 3D printing. The experimental results showed that the incorporating of CNTs could obviously increase the mechanical properties of the wood/PES composites material. The tensile strength, bending strength and elasticity modulus were 76.3%, 227.9% and 128.7% higher with 0.1wt% CNTs than without CNTs. And the mechanical properties of specimens firstly increased and then decreased with the increasing contents of CNTs. The SEM results of the specimens’ fracture morphology indicated that the preferable bonding interfaces between wood flour grains and PES grains were achieved by adding CNTs to the composites. There are two reasons to explain why the composites possessed the superior mechanical properties: CNTs could facilitate the laser sintering process of wood plastic composites due to their thermal conductivities; also, CNTs could directly reinforce the WPC composites as reinforcement.

The aim of this work is research dedicated to the search for new bactericidal systems for use in cosmetic formulations, dermocosmetics, or the production of wound dressings. Over the last two decades chitosan due to its special biological activity, has become a highly indispensable biopolymer with very wide application possibilities. Literature reports on the antibacterial effects of chitosan are very diverse, but our research has shown that they can be successfully improved through chemical modification. Therefore, in this study, results on the synthesis of new Schiff bases chitosan – dCsSB-SFD and dCsSB-PCA obtained using two aldehydes: sodium 4-formylbenzene-1,3-disulfonate (SFD) and 2-pyridine carboxaldehyde (PCA) respectively. Chitosan derivatives synthesized in this way demonstrate stronger antimicrobial activity. Carrying out the procedure of grafting chitosan with a caproyl chain allowed obtaining compatible blends of chitosan derivatives with κ-carrageenan, which are stable hydrogels with a high swelling coefficient. Furthermore, covalently bounded PCL improved the solubility of obtained polymers in organic solvents. With this respect, the Schiff base-containing polymers obtained in this study, with special hydrogel and antimicrobial properties are very promising materials for the potential use as a controlled-release formulation of both, hydrophilic and hydrophobic drugs in cosmetic products for skin health.

This study presents the synthesis and electrochemical evaluation of nitrogen-doped vanadium oxide (N-V2O3/C) as a cathode material for aqueous zinc-ion batteries (AZIBs), using a hydrothermal method. Compared to undoped V2O3/C, N-V2O3/C exhibits enhanced electrical conductivity, capacity, and electrochemical kinetics, attributed to the incorporation of pyridinic and pyrrolic nitrogen. Initial charge-discharge cycles indicate phase transitions to amorphous vanadium oxides, enhancing conductivity. N-V2O3/C shows a high specific capacity of 168.4 mAh g−1 at 10 A g−1 and remarkable reversibility, highlighted by the transient existence of intermediate species during cycling. Optimal electrochemical performance is achieved with a vanadium to nitrogen molar ratio of 2:3, indicating the significant impact of nitrogen doping concentration on the material’s efficiency. This work underscores the potential of N-V2O3/C as a superior cathode material for AZIBs.

Using density functional theory (DFT), the density of states of NH4V3O8 (NVO) was analyzed pre and post-oxygen defects (Od) formation. The findings revealed a reduced bandgap in NVO after Od introduction, emphasizing the role of Od in enhancing conductivity of the material, thus improving its electrochemical attributes. Through the water bath method, both NVO and its oxygen-deficient counterpart, (NH4)2V10O25⸱8H2O (NVOd), were synthesized as potential cathode materials for aqueous zinc-ion batteries (AZIBs). Experimental outcomes resonated with DFT predictions, highlighting the beneficial role of oxygen defects in boosting electrical conductivity. Notably, the refined material displayed a remarkable capacity of 479.3 mAh g-1 at 0.1 A g-1, underscoring its promise for advanced energy storage solutions.

Graph theory plays a crucial role in modeling and designing of chemical structure or chemical network. Chemical Graph theory helps to understand the molecular structure of molecular graph. The molecular graph consists of atoms as vertices and bonds as edges. Topological indices capture symmetry of molecular structures and give it a mathematical language to predict properties such as boiling points, viscosity, the radius of gyrations etc. In this article, we study the chemical graph of carbon Crystal structure of graphite and cubic carbon and compute several degree-based topological indices. Firstly we compute M-Polynomials of these structures and then from these M-polynomials we recover nine degree-based topological indices.

This study aims to investigate the effects of cement kiln dust (CKD) on the hydration reactions and mechanical properties of cement and to evaluate its potential for use as a supplementary cementitious material (SCM). The key variables are the CKD type and incorporation rate. Cement paste and mortar specimens containing CKD were prepared to examine their effects on the cement hydration and mechanical properties. The impact on hydration was assessed using setting time measurements, heat of hydration tests, and thermogravimetric analysis (TG). In addition, compressive strength tests were conducted to evaluate the effect of CKD on the mechanical properties of the cement. The results indicated that CKD promoted early cement hydration and enhanced the early age mechanical properties. However, owing to its lack of pozzolanic reactivity, it did not significantly affect long-term hydration. Given that the effects of CKD vary slightly depending on its chemical composition, careful consideration of CKD's properties suggests that its potential use as a SCM is promising.

The objective of this work is to study the physical and mechanical behavior of concrete with the addition of 0.5% and 1.0% of coconut fibers subjected to two chemical treatments in order to reduce their degradation and optimize their use in the elaboration of concrete specimens, which must comply with the standards of the American Society for Testing of Materials (ASTM), the American Concrete Institute (ACI) and the Instituto Ecuatoriano de Normalización (INEN). The coconut fibers were obtained from the raw material by hand and cut to a length of 4 cm. Subsequently, the coconut fibers were subjected to two chemical treatments: The first treatment is the immersion of the coconut fibers in 4% sodium hydroxide (NaOH) solution and the second treatment, the coconut fibers were immersed in gum arabic to consequently coat them with silica fume. A particular dosage was carried out with a proportion of 0.5% and 1.0% volume of coconut fiber for the two chemical treatments, replacing the volume of coarse aggregate. Simple concrete joists were made without fiber and with the post-treatment coconut fibers, which were subjected to flexural tests. The results indicated that the best chemical treatment is sodium hydroxide with a concentration of 4% and 1.0% coconut fiber for strengths of 210 kg/cm² and 240 kg/cm². In general, the joists with coconut fiber treated with sodium hydroxide outperformed the fibers treated with gum arabic and silica fume.

Synthetic materials such as Carbon, Kevlar, and Glass fibers are extensively utilized in various industries due to their superior characteristics including high stiffness, great strength, low den-sity, and high wear resistance, these advantages contributed to making them widespread in ap-plications like; aerospace, automobile, civil and electronics. This research is carried out to enhance the creep compliance of epoxy composite material by considering two types of fibers as reinforcement. A composite material is produced by combining two fibers, Kevlar fiber mixed with sika epoxy resin, along with Carbon fiber also mixed with sika epoxy resin using a Hand-Layup process. Experiments and numerical modeling are examined to offer a comprehensive understanding creep behavior of epoxy composite material in different weight ratios. Burger and Prony models are used to represent stress relaxation and creep strain of Visco-elastic material. According to the results, sika epoxy resin reinforced with Kevlar and Carbon fibers exhibits enhancement in the mechanical properties compared with pure epoxy. The use of Kev-lar/Sika epoxy composite results in higher creep compliance and modulus of elasticity compared with Carbon/Sika epoxy composite.

The work presents an approach to instrument the load sensing bearings for automotive applications for estimation of the loads acting on the wheels. The system comprises fiber-optic sensors based on addressed fiber Bragg structures (AFBS) with two symmetrical phase shifts. A mathematical model for load-deformation relation is presented, and the AFBS interrogation principle is described. The simulation includes (i) modeling of vehicle dynamics in a split-mu braking test, during which the longitudinal wheel loads are obtained, (ii) the subsequent estimation of bearing outer ring deformation using a beam model with simply supported boundary conditions, (iii) the conversion of strain into central wavelength shift of AFBS, and (iv) modeling of the beating signal at the photodetector. The simulation results show that the estimation error of the longitudinal wheel force from the strain data acquired from a single measurement point was 5.44% with root-mean-square error of 113.64 N. A prototype load sensing bearing was instrumented with a single AFBS sensor and mounted in a front right wheel hub of an experimental vehicle. The experimental setup demonstrated comparable results with the simulation during the braking test. The proposed system with load-sensing bearings is aimed at estimation of the loads acting on the wheels, which serve as input parameters for active safety systems, such as automatic braking, adaptive cruise control, or fully automated driving, in order to enhance their effectiveness and safety of the vehicle.

In this study, carbon blocks were fabricated using isotropic coke and coal tar pitch as raw materials, with a variation in pressure during cold isostatic pressing (CIP). The CIP pressure was set to 50, 100, 150, and 200 MPa, and the effect of the CIP pressure on the mechanical and electrical properties of the resulting carbon blocks was analyzed. Microstructural observations confirmed that after the kneading, the surface of isotropic coke was covered with the pitch components. Subsequently, after the CIP, granules, which were larger than isotropic coke and the kneaded particles, were observed. The formation of these granules was attributed to the coalescence of kneaded particles under the applied pressing pressure. This granule formation was accompanied by the development of pores, some remaining within the granules, while others were extruded, thereby existing externally. The increase in the applied pressing pressure facilitated the formation of granules, and this microstructural development contributed to enhanced mechanical and electrical properties. At a pressing pressure of 100 MPa, the maximum flexural strength was achieved at 33.3 MPa, and the minimum electrical resistivity was reached at 60.1 μΩm. The higher the pressing pressure, the larger the size of the granules. Pores around the granules tended to connect and grow larger, forming crack-like structures. This microstructural change led to degraded mechanical and electrical properties. The isotropic ratio of the carbon blocks obtained in this study was estimated based on the coefficient of thermal expansion (CTE). The results confirmed that all carbon blocks obtained proved to be isotropic. In this study, a specimen type named CIP-100 exhibited the best performance in every aspect as an isotropic carbon block.

Yttria stabilized zirconia (Y-TZP) ceramics with drastically reduced yttria content have been introduced by different manufacturers aiming at improving the damage tolerance of ceramic components. In this study an alumina doped 1.5Y-TZP was axially pressed, pressureless sintered in air at 1250–1400 °C for 2 h and characterized with respect to mechanical properties, microstructure and phase composition. The material exhibits a combination of high strength of 1000 MPa and a high toughness of 8.5–10 MPa√m. The measured fracture toughness is, however, extremely depending on measurement protocol. Direct crack length measurements overestimate toughness due to trapping effects. The initially purely tetragonal material has a high transformability of > 80 %, the transformation behavior is predominantly dilatoric, measured R-curve related toughness increments are in good agreement with transformation toughness increments derived from XRD data.

Process parameters influencing mechanical properties have always been a critical area of research for quite some time. We investigated the effect of laser power and laser scan velocity on the impact strength and maximum stress of 3D-printed metallic specimens of steel 1.2709 and 1.4542. Laser power significantly affected the impact strength and maximum stress of both the steels. With the increase in laser power, the impact strength increased for 1.2709 steel. However, there was a little increase in the impact strength with increasing laser power in the case of 1.4542 steel. Laser power had a decreasing impact on the maximum stress for 1.2709 steel. For 1.4542, maximum stress increased with increasing laser power, but then gradually declined. We observed that using laser power beyond 350W led to printing defect in the specimens, as maximum stress for some specimens reached close to zero in the case of 1.4542 steel. Laser scan velocity had a strong declining effect on the impact strength of 1.2709 steel.