In this paper, we present a full coverage path planning (CPP) algorithm for the marine surveys conducted in the convex polygon shaped search area. The survey is supposed to carry out by torpedo-type AUVs (autonomous underwater vehicles). Due to their nonholonomic mechanical characteristics, these vehicles have nonzero minimum turning radius. For any given polygon shaped search area, it can always be partitioned into one or more convex polygons. With this in mind, this paper proposes a novel search algorithm called CbSPSA (Calculation based Shortest Path Search Algorithm) for full coverage of any given convex polygon shaped search area. By aligning the search inter-tracks alongside the edge with the minimum height, we can guarantee the minimum number of the vehicle’s turns. In addition, the proposed method can guarantee the planned path is strictly located inside the polygon area without overlapped or crossed path lines, and also has the total path length as short as possible. Considering the vehicle’s nonzero minimum turning radius, we also propose a sort of smoothing algorithm to smooth the waypoint path searched by CbSPSA so as for the vehicle to exactly follow it. The smoothed path is also guaranteed to be strictly located inside the polygon. Numerical simulation analyses are also carried out to verify the effectiveness of the proposed schemes.

In this paper, we generalize the problems of finding simple polygons with the minimum area, maximum perimeter and maximum number of vertices so that they contain a given set of points and their angles are bounded by $\alpha+\pi$ where $\alpha$ ($0\leq\alpha\leq \pi$) is a parameter. We also consider the maximum angle of each possible simple polygon crossing a given set of points, and derive an upper bound for the minimum of these angles. The correspondence between the problems of finding simple polygons with the minimum area and maximum number of vertices is investigated from a theoretical perspective. We formulate the three generalized problems as nonlinear programming models, and then present a Genetic Algorithm to solve them. Finally, the computed solutions are evaluated on several datasets and the results are compared with those from the optimal approach.

Free route airspace (FRA) is a new concept of European air transport. It has been designed to eliminate the negative impact of air traffic on the environment, minimize fuel consumption, simplify and expand flight planning. In our research, FRA is modelled by using graph theory, networks, and convex analysis. We also looked for answers to the question which are the basic mathematical properties of airspace? Basic mathematical properties are expressed using axioms. Therefore, in our work, we state the general, basic axiom of airspace based on our FRA research. The axiom is given using practical, significant entry points and geodetic coordinates.

The article presents the Base Point Split (BPSplit) algorithm for generating a polygon skeleton based on sets of vector data describing lakes and rivers. A key feature of the BPSplit algorithm is that it is dependent on base points representing the source or mouth of a river or a stream. The input values of base points determine the shape of the resulting skeleton. Various skeletons can be generated with the use of different base points. Base points are applied to divide polygon boundaries into segments. Segmentation supports the selection of TIN edges inside polygons. The midpoints of selected TIN edges constitute a basis for generating a skeleton. The algorithm handles polygons with numerous holes, and it accounts for all holes. This article proposes a method for modifying a complex skeleton with numerous holes. In the discussed approach, skeleton edges that do not meet the preset criteria (e.g. that the skeleton is to be located between holes in the center of the polygon), are automatically removed. A simple algorithm for smoothing zigzag lines was proposed.

This article presents new PEM fuel cell models with hexagonal and pentagonal designs. After observing cell performance improvement in these models, we optimized them. Inlet pressure and temperature were used as input parameters, and consumption and output power were the target parameters of the multi-objective optimization algorithm. Then we used artificial intelligence techniques, including deep neural networks and polynomial regression, to model the data. Next, we employed the RSM (Response Surface Method) method to derive the target functions. Furthermore, we applied the NSGA-II multi-objective genetic algorithm to optimize the targets. Compared to the base model (Cubic), the optimized Pentagonal and Hexagonal models averagely increase the output current density by 21.819\% and 39.931\%, respectively.

Since the conventional split-merge algorithm is sensitive to the object scale variance and splitting starting point, a piecewise split-merge polygon approximation method is proposed to extract the object contour features. Specifically, the contour corner is used as the starting point for the contour piecewise approximation to reduce the sensitivity of the contour segment on the starting point; then, the split-merge algorithm is used to implement the polygon approximation for each contour segments. Both the distance ratio and the arc length ratio instead of the distance error are used as the iterative stop condition to improve the robustness to the object scale variance. Both the angle and length as two features describe the shape of the contour polygon, and affect each other along the contour order relationship. Since they have a strong coupling relationship. To improve the description correction of the contour, these two features are combined to construct a Coupled Hidden Markov Model to detect the object by calculating the probability of the contour feature. The proposed algorithm is validated on ETHZ Shape Classes and INRIA Horses standard datasets. Compared with other contour-based object detection algorithms, the proposed algorithm reduces the complexity of contour description, improves the robustness of contour features to scale variance, and has a higher object detection rate.

Air traffic congestion is caused by the unbalance between increasing traffic demand and saturating capacity. Flight delay not only causes huge economical lost, but also has very negative environmental impact in the whole air transportation system. In order to identify the impact of extended TMA on airport capacity, an airspace capacity assessment method based on augmented cell transmission model was proposed. Firstly, the airspace structure was modeled with points, segments, layers, and cells. Secondly, mixed integer linear programming model was built up with maximum throughput or capacity as the objective function. Finally, genetic algorithm was used to find the optimal result, and the results were validated by comparing with the fast-time simulation results generated by total airspace and airport modeler (TAAM) software. It is found that the proposed method could achieve a relatively accurate result in a much affordable and fast way. The numerical results could be very helpful for air traffic controllers to analyze the dynamic traffic flow entering and exiting TMA, so as to make decisions via reasonable analysis and do planning in advance by referring to the airport capacity.

This paper is based on the concept of absolute airspace and its local absolute stationary reference system proposed by the author, on the premise of abandoning space concept and the relativity principle of relativity theory, It is proposed that general relativity and special relativity can be unified into Simple and practical a space-time transformation theory which fully includes other basic physical principles of relativity. And the unified and simple expression of the time transformation effect is proved and deduced. By comparing with the theoretical derivation and checking calculation of Hafele-Keating experiment in an ideal state, It is proved that the expression of time transformation effect proposed in this paper is completely correct. Compared with the theory of relativity, the calculation is simpler and more accurate. The paper also puts forward two checking prediction of physical cases about the time transformation effect, which are left for the capable competent unit or individual to verify in practice.

Recurrent Pregnancy Loss (RPL) affects 1-2% of women, and its triggering factors are unclear. Several studies have shown the vaginal, endometrial, and gut microbiota may play a role in RPL. A decrease in the quantity of Lactobacillus crispatus in local microbiota has been associated with an increase in local (vaginal and endometrial) inflammatory response and immune cell activation that leads to pregnancy loss. The inflammatory response may be triggered by gram-negative bacteria, lipopolysaccharides (LPS), viral infections, mycosis, or atypia (tumor growth). Bacterial structures and metabolites produced by microbiota could be involved in immune cell modulation and may be responsible for immune cell activation and molecular mimicry. Gut microbiota metabolic products may increase the amount of circulating pro-inflammatory lymphocytes, which, in turn, will migrate into vaginal or endometrial tissues. Local proinflammatory Th1 and Th17 subpopulations along with a decrease in Treg and tolerogenic NK cells are accountable for the increase in pregnancy loss. Local microbiota may modulate the local inflammatory response increasing pregnancy success. Analyzing local and gut microbiota may be necessary to characterize some RPL patients. Although oral supplementation of probiotics has not been shown to modify vaginal or endometrial microbiota, the metabolites produced by it may benefit patients. Lactobacillus crispatus transplantation into the vagina may enhance the required immune tolerogenic response to achieve a normal pregnancy. The effect of hormone stimulation and progesterone to maintain early pregnancy on microbiota has not been adequately studied, and more research is needed in this area. Well-designed clinical trials are needed to ascertain the benefit of microbiota modulation in RPL.

Building outlines extracted from remote sensing images and raster maps often have irregular boundaries, redundant points, inaccurate positions, and unclear turns due to factors such as image quality, complexity of the surrounding environment, and extraction methods. This study proposes a regularization algorithm for right-angled polygon building outlines with jagged edges. First, the minimum bounding rectangle of the building outline is established and populated with a square grid based on the smallest visible length principle. An overlay analysis is then applied to the grid and original building to extract the turning points of the outline. Finally, the building orientation is used as a reference axis to sort the turning points and reconstruct the simplified building outline. Analysis of the experimental results shows that the proposed simplification method enhances the morphological characteristics of building outlines, such as parallelism and orthogonality, while considering simplification principles, such as the preservation of direction, position, area, and shape of the building. The proposed algorithm provides a new regularization method for building outlines with jagged edges.

The UK aviation industry is committed to achieving net zero emissions by 2050 through sustainable measures, and one of the key aspects of this effort is the implementation of Unmanned Traffic Management (UTM) systems. These UTM systems play a crucial role in enabling the safe and efficient integration of unmanned aerial vehicles (UAVs) into the airspace. As part of the Airspace of the Future (AoF) project, the development and implementation of UTM services have been prioritized. The paper aims to create an environment where routine drone services can operate safely and effectively. To facilitate this, a digital twin of the National Beyond Visual Line of Sight Experimentation Corridor has been created. This digital twin serves as a virtual replica of the corridor and allows for the synthetic testing of unmanned traffic management concepts. The implementation of the digital twin involves both simulated and hybrid flights with real drones. Simulated flights allow for the testing and refinement of UTM services in a controlled environment. Hybrid flights, on the other hand, involve the integration of real drones into the airspace to assess their performance and compatibility with the UTM systems. By leveraging the capabilities of UTM systems and utilizing the digital twin for testing, the AoF project aims to advance the development of safer and more efficient drone operations. Experimentation Corridor has been developed to simulate and test concepts related to managing unmanned traffic. The paper provides a detailed account of the implementation of the digital twin for the AoF project, including simulated and hybrid flights involving real drones.

The affinity constant, also known as the equilibrium constant, binding constant, equilibrium association constant, or the reciprocal value, the equilibrium dissociation constant (K_d), can be considered as one of the most important characteristics for any antibody-antigen pair. Many methods based on different technologies have been proposed and used to determine this value. However, since a very large number of publications and commercial datasheets do not include this information, significant obstacles in performing such measurements seem to exist. In other cases where such data are reported, the results have often proved to be unreliable. This situation may indicate that most of the technologies available today require a high level of expertise that does not seem to be available in many laboratories. In this paper, we present a simple approach based on standard immunoassay technology that is easy and quick to perform. It relies on the effect that the molar IC₅₀ approaches the K_d value in the case of infinitely small concentrations of the reagent concentrations. A two-dimensional dilution of the reagents leads to an asymptotic convergence to K_d. The approach has some similarity to the well-known checkerboard titration used for the optimization of immunoassays. A well-known antibody against the FLAG peptide, clone M2, was used as a model system and the results were compared with other methods. This approach could be used in any case where a competitive assay is available or can be developed. The determination of an affinity constant should belong to the crucial parameters in any quality control of antibody-related products and assays and should be mandatory in papers using immunochemical protocols.

LCK, a member of the Scr kinase family, is a non-receptor tyrosine kinase involved in immune cell activation, antigen recognition, tumor growth, and cytotoxic response. The enzyme has usually been linked to T lymphocyte activation upon antigen recognition. Lck activation is central to CD4, CD8, and NK activation. However, recently, it has become clearer that activating the enzyme in CD8 cells can be independent of antigen presentation and enhance cytotoxic response. The role of Lck in NK cytotoxic function has been controversial in a similar fashion as the role of the enzyme in CAR T cells. Inhibition of Lck has been mainly to treat hematologic malignancies with a high rate of success. They may be useful in treating other tumor types, and they may be useful to prevent cell exhaustion. New, more selective inhibitors have been documented, and they have shown inter-esting activities not only in tumor growth but in the treatment of autoimmune diseases, asthma, and graft vs host disease. Drug repurposing and bioinformatics can aid in solving several unsolved is-sues on the role of Lck in cancer. In summary, the role of Lck in immune response and tumor growth is not a simple event and requires more research.

The paper suggests that the physical priciple of special relativity's space-time transformation effect is wrong, Uniform linear motion without acceleration does not exist objectively, nor does its same reference frames. Therefore, it is inferred that the space-time transformation effect of special relativity is caused by the acceleration of moving objects, special relativity is only a part of general relativity, not a theoretical system that exists independently from general relativity. The corresponding mathematical demonstration and calculation verification are carried out, and the result proves that the inference of the paper is correct. At the same time, it further explains that the concept of absolute airspace is correct. Special relativity has serious errors in the concept of space, the principle of relativity and the physical principle of space-time transformation effect. Therefore, it is necessary to make a series of revisions to the theory of relativity and to reinterpret some related physical problems.

In this paper, the concept of absolute airspace is further elaborated, and the time transform effect, the frequency transform relation of clock timing, and the principle of Doppler effect of special relativistic light are analyzed and demonstrated. Based on the concept of absolute airspace, a new and accurate Doppler effect relation of light (electromagnetic wave) is proposed. It is proved that there is a synchronous relationship between the time shift effect and the frequency change of the timing inside the clock. When the light (electromagnetic wave) source is in motion, the Doppler effect includes two physical mechanisms: the frequency change caused by time transformation effect and the frequency change caused by relative motion. When the light source is in motion, the Doppler effect of the light there are some differences in different directions due to the rotation of the earth. The relation of Doppler effect of special relativistic light is only a highly approximate relation, and its theoretical basis, special relativity, is flawed in principle.

Urban ultra-low altitude airspace (ULAA) presents unique challenges for unmanned aerial vehicle (UAV) path planning due to high building density and regulatory constraints. This study analyzes and improves classical path planning algorithms for UAVs in ULAA. Experiments were conducted using A*, RRT, RRT*, and artificial potential field (APF) methods in a simulated environment based on building data from Chengdu City, China. Results show that traditional algorithms struggle in dense obstacle environments, particularly APF due to local minima issues. Enhancements were proposed: a density-aware heuristic for A*, random perturbation for APF, and a hybrid optimization strategy for RRT*. These modifications improved computation time, path length, and obstacle avoidance. The study provides insights into the limitations of classical algorithms and suggests enhancements for more effective UAV path planning in urban environments.

The principal aim of a spectral observer is twofold: the reconstruction of a signal of time via state estimation and the decomposition of such a signal into the frequencies that make it up. A spectral observer can be catalogued as an online algorithm for time-frequency analysis because is a method that can compute on the fly the Fourier transform (FT) of a signal, without having the entire signal available from the start. In this regard, this paper presents a novel spectral observer with an adjustable constant gain for reconstructing a given signal by means of the recursive identification of the coefficients of a Fourier series. The reconstruction or estimation of a signal in the context of this work means to find the coefficients of a linear combination of sines a cosines that fits a signal such that it can be reproduced. The design procedure of the spectral observer is presented along with the following applications: (1) the reconstruction of a simple periodical signal, (2) the approximation of both a square and a triangular signal, (3) the edge detection in signals by using the Fourier coefficients, (4) the fitting of the historical Bitcoin market data from 2014-12-01 to 2018-01-08 and (5) the estimation of a input force acting upon a Duffing oscillator. To round out this paper, we present a detailed discussion about the results of the applications as well as a comparative analysis of the proposed spectral observer vis-à-vis the Short Time Fourier Transform (STFT), which is a well-known method for time-frequency analysis.

(1) Background: Stereological estimations significantly contributed to our anatomical and physiological understanding of the lung by providing an average distribution of measured parameters over the entire lung parenchyma. However, most structural lung diseases show a very inhomogeneous pattern of alterations. (2) Methods: We developed a novel protocol for the analysis of all pulmonary airspaces. Our pipeline starts with high-resolution synchrotron radiation-based X-ray tomographic microscopy (SRXTM) and consists of (i) image segmentation with the combination of the free machine-learning tool Ilastik and ImageJ and (ii) calculation of the airspace diameter distribution of an entire lung using a diameter map function. To evaluate the new pipeline, lungs from adult mice with cystic fibrosis (CF)-like lung disease (ENaC-transgenic mice) or mice with elastase-induced emphysema were compared to healthy controls. (3) Results: We were able to show the distribution of airspace diameters throughout the entire lung, as well as separately for the conducting airways and the gas-exchange area. In the pathobiological context, we observed an irregular widening of parenchymal airspaces in mice with CF-like lung disease and elastase-induced emphysema. Comparable results were obtained when analyzing lungs imaged with μCT, suggesting that our pipeline is applicable to different kinds of imaging modalities. (4) Conclusions: We conclude that the airspace diameter map is well suited for a detailed analysis of unevenly distributed structural alterations in chronic muco-obstructive lung diseases such as cystic fibrosis and COPD.

This paper presents the design of a digital twin that blends aviation, gaming, simulation, and Geographic Information Systems (GIS) to create a synthetic environment within which strategies, laws and platforms for electric aviation may be tested out. This digital twin has been called Future Urban Synthetic Environment (FUSE). FUSE includes an in-built Unmanned Traffic Management (UTM) that can be used to run simulations to test the coordination of all urban traffic. It uses real GIS tagged imagery data and implements it at runtime into the game engine and thus link the optimised imagery loading to the visual performance of the simulation engine. FUSE provides a 3D digital twin of specified areas designed to simulate the effects (in terms of noise, visual impact, privacy) of drones and electric air taxis operating under various operational scenarios (such as number of deliveries allowed per day, maximum payload weight, no-fly areas, position of depots, vertiports, etc.). With so much high-fidelity data it is difficult for any game system to effectively render the environment and do justice to the detail whilst enabling enough of the landscape to be rendered to keep in focus the detail when looking out at the horizon.

Neurologic disorders such as traumatic brain injury, multiple sclerosis, Alzheimer’s disease, and drug-resistant epilepsy have a high socioeconomic impact around the world. Current therapies for these disorders are often not effective. This creates a demand for the development of new therapeutic approaches to treat these disorders. Recent data suggest that autoreactive naturally occurring immunoglobulins produced by subsets of B cells called B1 B cells combined with complement are actively involved in the processes of restoration of neuronal functions during pathological conditions and remyelination. The focus of this review is to discuss the possibility of creating specific therapeutic antibodies that can activate and fix complement to enhance neuronal survival and promote central nervous system repair after injuries associated with many types of neurodegenerative diseases.

We investigated the dynamics of a simple master equation describing the evolution of a probability distribution between two states, \( p_1 \) and \( p_2 \) (with \( p_1 + p_2 = 1 \)). Our focus is on the behavior of the entropy \( S \), the distance \( D \) from the uniform distribution (\( p_1 = p_2 = 1/2 \)), and the free energy \( F \). We define two ratios, \( \eta_S = \frac{dS/dt}{dF/dt} \) and \( \eta_D = \frac{dD/dt}{dF/dt} \), and find that both diverge to plus-minus infinity as the system evolves towards the uniform distribution. This divergence marks a critical transition point where the master equation temporarily loses physical meaning. However, after this divergence, the system settles into a new, well-behaved regime where the solutions stabilize at finite values, representing a new equilibrium or steady state. This two-regime behavior underscores the intricate dynamics of simple probabilistic systems as they approach and surpass equilibrium, providing insights into the complex interplay of entropy, distance, and free energy in statistical mechanics.

In order to understand the evolution of multicellularity, we must understand how and why selection favors the first steps in this process: the evolution of simple multicellular groups. Multicellularity has evolved many times in independent lineages with fundamentally different ecologies, yet no work has yet systematically examined these diverse selective drivers. Here we review recent developments in systematics, comparative biology, paleontology, synthetic biology, theory, and experimental evolution, highlighting ten selective drivers of simple multicellularity. Our survey highlights the many ecological opportunities available for simple multicellularity, and stresses the need for additional work examining how these first steps impact the subsequent evolution of complex multicellularity.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

Current antibiograms cannot discern the particular effect of a specific antibiotic when the bacteria are incubated with a mixture of antibiotics. To prove that this task is achievable, Escherichia coli strains were treated with ciprofloxacin for 45 min, immobilized on a slide and stained with SYBR Gold. In susceptible strains, the nucleoid relative surface started to decrease near the MIC, being progressively condensed as dose increased. The shrinkage level correlated with the DNA fragmentation degree. Ciprofloxacin-resistant bacilli showed no change. Additionally, E. coli strains were incubated with ampicillin for 45 min and processed similarly. The ampicillin-susceptible strain revealed intercellular DNA fragments that increased with dose, unlike the resistant strain. Co-incubation with both antibiotics revealed that ampicillin did not modify the nucleoid condensation effect of ciprofloxacin, whereas the quinolone partially decreased the background of DNA fragments induced by ampicillin. Sixty clinical isolates, with different combinations of susceptibility-resistance to each antibiotic, were co-incubated with the EUCAST breakpoints of susceptibility of ciprofloxacin and ampicillin. The morphological assay correctly categorized all the strains for each antibiotic in 60 min, demonstrating the feasible independent evaluation of a mixture of quinolone and beta-lactam. The rapid phenotypic assay may shorten the incubation times and necessary microbial mass currently required for evaluation.

Meaning understood in terms of teachability and learnability is crucial to Wittgenstein’s later work. As regards the resolution of philosophical problems – and epistemological problems in particular - this approach seems to posit a hierarchy of meaning that excludes endless deferral. This is the basis of Wittgenstein’s attack on philosophical scepticism. Derrida’s approach to language seems to require both non-hierarchy and endless deferral. Consequently fundamental to his concept of origin is identity and difference simultaneously, irreducibly, non-simply. One question is whether it is possible for there to be a compromise between the two philosophers: a hierarchy of meaning that does not in principle exclude endless deferral.

We study Hadamard's variational formula for simple eigenvalues under dynamical and conformal deformations. Particularly, harmonic convexity of the first eigenvalue of the Laplacian under the mixed boundary condition is established for two-dimensional domain, which implies several new inequalities.

We developed a novel approach in the field of spatiotemporal modelling, based on the spatialisation of time: the Timescape algorithm. It is especially aimed at sparsely distributed datasets in ecological research, whose spatial and temporal variability is strongly entangled. The algorithm is based on the definition of a spatiotemporal distance that incorporates a causality constraint and that is capable of accommodating the seasonal behaviour of the modelled variable as well. The actual modelling is conducted exploiting any established spatial interpolation technique, substituting the ordinary spatial distance with our Timescape distance, thus sorting, from the same input set of observations, those causally related to each estimated value at a given site and time. The notion of causality is expressed topologically and it has to be tuned for each particular case. The Timescape algorithm originates from the field of stable isotopes spatial modelling (isoscapes), but in principle it can be used to model any real scalar random field distribution.

Muon tomography leverages cosmic muons’ exceptional penetration capabilities to reconstruct detailed tomographic images via multiple Coulomb scattering interactions, making it invaluable for detecting High-Z materials critical to homeland security. This study introduces the Slope Intercept (SI) algorithm, a novel approach for rapid and precise tomographic image reconstruction. Implemented using Geant4 simulations in a standard-sized container tomography station, SI demonstrates superior performance in speed and simplicity compared to traditional methods. While the imaging results of SI and the Point of Closest Approach (POCA) algorithm are nearly identical, the SI algorithm is simpler to implement, requires shorter CPU time, and exhibits a smaller margin of error. Its computational efficiency and simplicity make it a robust alternative to the POCA algorithm. These findings highlight SI’s suitability for applications demanding robust imaging and efficient data processing, which are crucial for advancing security measures and scientific research.

In this study, the degradation characteristics of radio-frequency (RF) low-noise amplifier (LNA) based on silicon-germanium (SiGe) heterojunction bipolar transistors (HBTs) due to total ionizing dose (TID) are investigated. The small-signal equivalent model of a SiGe HBT is utilized to analyze circuit-level performance including the input and the output matching and noise figure (NF). As a target circuit, an LNA with a cascode common-emitter stage with emitter degeneration is studied and the equation of each performance parameter is derived. The RF LNA fabricated using commercial 350 nm SiGe technology was exposed to X-ray irradiation with the total dose up to 3 Mrad (SiO2). The experimental results exhibit that modeled device parameters estimate the degraded circuit performance. In addition, the relative impact of each parameter on the circuit metrics is revealed, which is expected from the derived design equations. The key device parameters for modeling TID-induced circuit degradations include the base resistance, the transconductance, and the base-to-emitter capacitance.

(1) Background: Cardiorespiratory fitness (CRF) is a prognostic factor regarding long time morbidity and mortality. To assess CRF the well-known gold standard is cardiopulmonary exercise testing (CPET), which is a time consuming and expensive test. Therefore, alternative methods for routine evaluation of CRF are needed for the general population as well as for specific patient groups such as children and young adults with congenital heart disease. The Stair Climbing Test (SCT) is a simple and resource saving test reported in the current literature. This test is used in various settings to assess different health associated risk factors including cardiorespiratory fitness, muscular resilience, therapy effectiveness or pre- and postoperative morbidity and mortality.

We are witnessing a dramatic transformation in the way we do science. In recent years, significant flaws with existing scientific methods have come to light, including lack of transparency, insufficient involvement of stakeholders, disconnection from the public, and limited reproducibility of research findings. These concerns have sparked a global movement to revolutionize scientific practice and the emergence of Open Science. This new approach to science extends principles of openness to the entire research cycle, from hypothesis generation to data collection, analysis, replication, and translation from research to practice. Open Science seeks to remove all barriers to conducting high quality, rigorous, and impactful scientific research by ensuring that the data, methods, and opportunities for collaboration are open to all. Emerging digital technologies and "big data" (see "Ten simple rules for responsible big data research") have further accelerated the Open Science movement by affording new approaches to data sharing, connecting researcher networks, and facilitating the dissemination of research findings. Open scientific practices are also having a profound impact on the health sciences and medical research, and specifically how we conduct clinical research with human participants. Human health research necessitates careful considerations for practicing science in an ethical manner. There is also a particular urgency to human health research since the goal is to help people, so doing good science takes on a different meaning than simply doing science well. It also implores the scientist to reassess the conventional view of human health research as a pursuit conducted by scientists on human subjects, and lays a greater emphasis on inclusive and ethical practices to ensure that the research takes into account the interests of those who would be most impacted by the research. Openness in the context of human health research also raises greater concerns about privacy and security and presents more opportunities for people, including participants of research studies, to contribute in every capacity. At the core of open health research, scientific discoveries are not only the product of collaboration across disciplines, but must also be owned by the community that is inclusive of researchers, health workers, and patients and their families. To guide successful open health research practices, it is essential to carefully consider and delineate its guiding principles. This editorial is aimed at individuals participating in health science in any capacity, including but not limited to people living with medical conditions, health professionals, study participants, and researchers spanning all types of disciplines. We present ten simple rules that, while not comprehensive, offer guidance for conducting health research with human participants in an open, ethical, and rigorous manner. These rules can be difficult, resource-intensive, and can conflict with one another. They are aspirational and are intended to accelerate and improve the quality of human health research. Work that fails to follow these rules is not necessarily an indication of poor quality research, especially if the reasons for breaking the rules are considered and articulated (see rule 6: document everything). While most of the responsibility of following these rules falls on researchers, anyone involved in human health research in any capacity can apply them.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

With the growth of air traffic demand in busy airspace, there is an urgent need for airspace sectorization to increase air traffic throughput and ease the pressure on controllers. The purpose of this paper is to develop a method framework that can perform airspace sectorization automatically, reasonably, which can be used as an advisory tool for controllers as an automatic system, especially for eliminating irregular sector shapes generated by simulated annealing algorithm (SAA) based on region growth method. Two graph cutting method, dynamic Monte Carlo method by changing location of flexible vertices (MC-CLFV) and Monte Carlo method by radius changing (MC-RC) were developed to eliminating irregular sector shapes generated by SAA in post-processing. The experimental results show that the proposed method framework of AS can automatically and reasonably generate sector design schemes that meet the design criteria. Our methodology framework and software can provide assistant design and analysis tools for airspace planners to design airspace, improve the reliability and efficiency of airspace design, and reduce the burden of airspace planners. In addition, this lays the foundation for reconstructing airspace with more intelligent method.

Sacrococcygeal pilonidal disease is a chronic inflammatory condition with an incidence of 26:100,000 in the United States. However, its etiology and optimal treatment remain controversial. We included 129 and 74 patients with simple and complex sacrococcygeal pilonidal disease, respectively. The primary outcome was pilonidal sinus recurrence after unroofing curettage. Secondary outcomes were pain scores, time to return to work/school, and time to complete recovery. At a median follow-up of 53 months, the recurrence rate was 4.9% in all patients, not significantly higher in subjects with the complex disease. Duration of surgery (15.4 vs. 12.2 min), time to return to school/work (9.8 vs. 7.7 days), and complete healing time (44 vs. 36 days) were longer in patients with the complex disease. Postoperative complication rates, pain scores, and quality of life scores between the two groups did not differ. Unroofing curettage may be a good first-choice treatment for both simple and complex sacrococcygeal pilonidal disease.

With reference to Planck scale Hubble parameter, super luminal expansion speeds, super luminal rotation speeds, Mach’s principle and Holographic principle, we review the current cosmological observations with eight simple assumptions. By understanding Yuri N. Obukhov and V.A. Korotky proposed cosmic rotational effects of polarization of radiation due to massive bodies, to some extent cosmic rotation can be deep-rooted in an observational approach and the ratio of current angular velocity and Hubble parameter can be estimated. It is possible to show that, at H₀ =70 km/sec/Mpc, current cosmic temperature, age, radius, mass, mass density are 2.721 K, 4.41x10¹⁷ sec, 90 billion light years, 1.14654x10⁵⁴ kg, 0.0482 times the current critical density respectively. Clearly speaking, current universe seems to constitute 267 Hubble spheres. Important point to be noted is that, current rotational kinetic energy is 0.6667 times the current critical energy. Based on the estimated current mass density and current rotational kinetic energy, current cosmic dark matter density can be shown to be 0.2851 times the current critical density. These numerical coincidences cast serious doubt on the on the real existence of currently believed ‘dark energy’. Initial and current expansion speeds are 3x10⁸ m/sec and 3.56x10⁹ m/sec respectively. With increasing cosmic age and increasing cosmic expansion speed, current universe is expanding with a speed of 11.885c. By knowing the time to time future cosmic temperatures, future Hubble parameters and corresponding future cosmic expansion speeds can be estimated and thus future expansion speed can be understood. Starting from ‘speed of light’, our model assumes a continuous increase in expansion speed and attains a current radius of 90 billion light years (without inflationary concepts) and casts a serious doubt on the actuality of currently believed ‘inflation’.

Language models like BERT dominate current NLP research due to their robust performance, but they are vulnerable to backdoor attacks. Such attacks cause the model to consistently generate incorrect predictions when specific triggers are present in the input, while maintaining normal behavior on clean inputs. In this paper, we propose a straightforward data poisoning method targeting the BERT architecture. Our approach does not involve complex modifications to the model or its training process; instead, it relies solely on altering a small portion of the training data. By introducing simple perturbations into just 10% of the training dataset, we demonstrate the feasibility of injecting a backdoor into the model. Our experimental results show a high attack success rate, indicating that the model trained on the poisoned data can reliably associate the trigger with the attacker's desired outputs while its performance on clean data remains unaffected. This highlights the stealth and effectiveness of our method, emphasizing the need for improved defensive strategies to protect against such threats. Our study underscores the critical importance of ongoing research and development to safeguard AI systems from malicious exploitation, ensuring the security and reliability of NLP applications.

In this brief paper we will propose a new equation for the proton charge radius. We will base our new equation on the Trinhammer-Bohr formula which states that the proton charge radius is directly proportional to the proton Compton wavelength. We will then propose a new equation for the proton Compton wavelength which is inversely proportional to the Rydberg constant and directly proportional to the running value of the fine structure constant on the protonic scale. This will define the proton charge radius only by the effective value of the fine structure constant and the Rydberg constant. This new equation also disproves the old value of the proton charge radius 0.877(50) which was measured by using electron-proton scattering and further solidifies the newer and smaller values 0.8414(19) provided by NIST.

Pre-trained Language Models (PTLM) have remarkable and successful performance in solving lots of NLP tasks nowadays. And previous researchers have created many SOTA models and these models are included in many long surveys(Qiu et al., 2020). So, we would like to conduct a simple and short survey on this topic to help researchers understand the sketch of PTLM more quickly and comprehensively. In this short survey, we would provide a simple but comprehensive review of techniques, benchmarks, and methodologies in PTLM. And we would also introduce the applications evaluation of PTLM in this simple survey.

This manuscript aims to share some tips on implementing a flipped classroom, with examples from biology and computational biology. The proposed rules are: - Invert time and Say It, - Identify (or create) resources for learning at home, - Be explicit on the acquisition of knowledge and engage students at home, - Explore active learning in class, - Develop skills of cooperation and sharing, - Evaluate, - Differentiate, - Take care of the logistic and your posture, - Document your flipped classroom, - Share.

This paper presents a new method to model the nonlinear behaviour of masonry double curvature structures, possibly reinforced by composite materials, by means of conventional elasto-plastic analyses. It is meant to be used in professional design, especially for assessment and retrofitting purposes, therefore based on the exploitation of the simplest nonlinear Finite Elements available in a commercial software, namely trusses with elasto-fragile and elasto-ductile behaviour (Cutoff Bars). The numerical static nonlinear analyses are carried out by considering elastic hexahedral elements for bricks and lumping nonlinearities on joints. These have been assumed in turn elastic-brittle and elastic-plastic by using 1D elements, respectively Point Contacts, under No-Tension Material hypothesis, and Cutoff Bars, assigning small tensile resistance to the material. The reinforcement, realised with FRP hooping strips, has been successfully modelled in a similar fashion, i.e. by applying perfectly bonded elastic-plastic Cutoff Bars at the extrados of the dome, where the debonding is accounted for in a conventional way limiting the tensile strength according to Italian Standards indications. The procedure is validated against benchmark models with the same geometry, using experimental data and more refined structural model results for comparison.

Assessment of the genetic distinctiveness of a cultivar through morphological descriptors is an important tool for both the registration and the protection. New mango genotypes have been improved using valuable diverse germplasm resources to ensure food security. DNA fingerprinting based simple sequence repeats (SSR)-markers have been the most broadly used, effective and accurate in evaluation of genetic characterization of a cultivar. Molecular breeding is an effective source of genetic gain after improvement of fruit trees using marker assisted genomic selection. Mango (Mangifera indica L.) is an allotetraploid (2n = 4X= 40) drupe fruit and has high nutritional value belongs to genus Mangifera and family Anacardiaceae. Mango cultivars are used with worldwide acceptance to pharmacological, ethnomedical, and phytochemical industries. This study investigated the molecular evaluation of a new mango cultivar ‘Azeem Chaunsa’ using a set of the most effective 50 hyper-variable polymorphic SSR markers. Highly specific DNA fingerprints were identified in the genome of this mango cultivar, ‘Azeem Chaunsa’ compared with three standard cultivars such as Sindhri, Samar Bahisht (S.B) Chaunsa and Sufaid Chaunsa. Our results showed that SSR markers could efficiently assess genetic diversity in mango. An agglomerative hierarchical clustering method was used to construct dendrogram based on the ‘Unweighted Pair- Group Method with Arithmetic Mean’ (UPGMA). The genetic similarity coefficients were recorded between the mangos cultivars ranged from 0.49 to 0.67. Cultivar identification (CID) evaluates association among standard cultivars and Azeem Chaunsa and further concludes significant variations. CID results concluded that cultivar ‘Azeem Chaunsa’ varied significantly from the check cultivar, Sindhri (46.2%), S.B Chaunsa (45%) and Sufaid Chaunsa (46.7%). The results obtained in this study will orient cultivar identification strategies for a successful future mango breeding programmes in the context of climate change.

The relativistic Doppler effect comes from the fact that observers in different inertial reference frames experience space and time differently, while the speed of light remains always the same. Consequently, a wave packet of light exhibits different frequencies, wavelengths, and amplitudes. In this paper, we present a local approach to the relativistic Doppler effect based on relativity, spatial and time translational symmetries, and energy conservation. Afterward, we investigate the implications of the relativistic Doppler effect for the quantum state transformations of wave packets of light and show that a local photon is a local photon at the same point in the spacetime diagram in all inertial frames.

Korenaga and coworkers present evidence to suggest that 4.3 billion years ago the Earth’s mantle was dry and water filled the ocean to twice its present volume.[2] CO₂ was constantly exhaled during the mafic to ultramafic volcanic activity associated with magmatic plumes that produced the thick, dense and relatively stable oceanic crust. In that setting two distinct major types of sub-marine hydrothermal vents were active: ~400 °C acidic springs whose effluents bore vast quantities of iron into the ocean, and ~120 °C, highly alkaline and reduced vents exhaling from the cooler, serpentinizing crust at some distance from the heads of the plumes. When encountering the alkaline effluents, the iron from the plume head vents precipitated out forming mounds likely surrounded by voluminous exhalative deposits similar to the banded iron formations known from the Archean. These mounds and the surrounding sediments likely comprising nanocrysts of the variable valence FeII/FeIII oxyhydroxide, green rust. The precipitation of green rust, along with subsidiary iron sulfides and minor concentrations of Ni, Co and Mo in the environment at the alkaline springs may have established both the key bio-syntonic disequilibria, and the means to properly make use of them – those needed to drive the essential inanimate-to-animate transitions that launched life. In the submarine alkaline vent model for the emergence of life specifically it is first suggested that the redox-flexible green rust microcrysts spontaneously formed precipitated barriers to the complete mixing of carbonic ocean and alkaline hydrothermal fluids, barriers that created and maintained steep ionic disequilibria; and second, that the hydrous interlayers of green rust acted as 'engines' that were powered by those ionic disequilibria and drove essential endergonic reactions. There, aided by sulfides and trace elements acting as catalytic promoters and electron transfer agents, nitrate could be reduced to ammonia and carbon dioxide to formate, while methane may have been oxidized to methyl and formyl groups. Acetate and higher carboxylic acids could then have been produced from these C1 molecules and aminated to amino acids, and thence oligomerized to offer peptide nests to phosphate and iron sulfides and secreted to form primitive amyloid-bounded structures, leading conceivably to protocells.

Systemic AL amyloidosis is a challenging disease for which many patients are considered frail in daily clinical practice. However, no study has so far addressed frailty and its impact on the outcome of these patients. We built a simple score to predict mortality based on three frailty-associated variables: age, ECOG performance status (<2 vs. 2) and NT-proBNP (<8500 vs. 8500 ng/L). Four-hundred and sixteen consecutive newly diagnosed patients diagnosed at ten sites from the Spanish Myeloma Group were eligible for the study. The score was developed in a derivation cohort from a referral center, and it was externally validated in a multicenter cohort. On multivariate analysis the three variables were independent predictors of survival. The score was able to discriminate four groups of patients in terms of overall survival and early mortality in both cohorts. Comorbidity was also analyzed with the Charlson comorbidity index, but it did not reach statistical significance in the model. A nomogram was created to easily estimate the mortality risk of each patient at each time point. This score is a simple, robust, and efficient approach to dynamically assess frailty-dependent mortality both at diagnosis and throughout the follow-up. The optimal treatment for frail AL amyloidosis patients remains to be determined but we suggest that the estimation of frailty-associated risk could complement current staging systems, adding value in clinical decision-making in this complex scenario.

Crop disease classification has always been a critical and persistent problem in the field of agricultural and forestry sciences, where often we do not have access to a sufficient number of samples to know the distribution of real-world samples. How to make full use of the existing data is the starting point of our thinking. To address this problem, this paper proposes a supervised image augmentation method Negative Contrast, which uses the contrast images of existing disease samples after removing disease areas as negative samples for image augmentation when samples are relatively scarce. Numerous experiments have shown that several classical models using this augmentation method have improved in disease classification of four crops, rice, wheat, corn, and soybean, with a maximum accuracy improvement of 30.8%. In addition, the comparative analysis of attentional heat map shows that the model using Negative Contrast is more accurate and intense on the area of interest of diseases, and thus reflects better generalization ability in real-world disease classification. Our dataset and codes can be found in https://www.kaggle.com/datasets/w970704112/corn-wheat-rice-soybean and https://github.com/hiter0/contrastaug .

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

To solve two key problems in the identification of people who are infected with COVID-19: the first problem is that the identification accuracy is not high enough. The second problem is that present identification method such as nucleic acid testing is expensive in many countries. Methods: So, I decided to design a fast identification method for COVID-19 patients which is based on deep learning. After the model (CoughNet) learns more than 6,000 cough spectrograms of both COVID-19 patients and normal people, the accuracy rate of identification of COVID-19 patients and normal people is higher than 99% in the test set. Structure: This paper is mainly divided into three parts: the first part introduces the main background and research status of the research; The second part introduces the research methods; The third part introduces the specific process of the experiment.

Science continues to become more interdisciplinary and to involve increasingly complex data sets. Many projects in the biomedical and health-related sciences follow or aim to follow the principles of FAIR data sharing, which has been demonstrated to foster collaboration, to lead to better research outcomes, and to help ensure reproducibility of results. Data generated in the course of biomedical and health research present specific challenges for FAIR sharing in the sense that they are heterogeneous and highly sensitive to context and the needs of protection and privacy. Data sharing must respect these features without impeding timely dissemination of results, so that they can contribute to time-critical advances in medical therapy and treatment. Modeling and simulation of biomedical processes have become established tools, and a global community has been developing algorithms, methodologies, and standards for applying biomedical simulation models in clinical research. However, it can be difficult for clinician scientists to follow the specific rules and recommendations for FAIR data sharing within this domain. We seek to clarify the standard workflow for sharing experimental and clinical data with the simulation modeling community. By following these recommendations, data sharing will be improved, collaborations will become more effective, and the FAIR publication and subsequent reuse of data will become possible at the level of quality necessary to support biomedical and health-related sciences.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

During the COVID-19 pandemic face masks grew in importance as their use by the general population was recommended by health officials in order to minimize the risk of infection and prevent further spread of the virus. To ensure health protection of medical personal and other system relevant staff, it is of considerable interest to quickly test if a certain lot of filtering facepiece masks meets the requirements or if the permeability changes under different conditions. As certified penetrometers are rather expensive and were difficult to obtain during the COVID-19 pandemic, we describe two quite simple and cheap methods to quickly test the filter permeability based on an electronic cigarette. The first method uses a precision scale, the second method uses a light scattering detector to measure the filter penetration. To make sure these two methods yield reliable results, both were tested with freshly cut filter samples covering the range of approx. 7% to 60% permeability and compared to the results of a certified penetrometer. The comparison of the two methods with the certified penetrometer showed a good correlation and therefore allow a quick and rather reliable estimation of the permeability. Several examples about the use of faulty masks and the resulting health risks show that simple, fast, cheap and broadly available methods for filter characterization might be useful in these days.

Volcanic emissions (ash, gas, aerosols) dispersed in the atmosphere during explosive eruptions generate hazards affecting aviation, human health, air quality and the environment. We document for the first time the contamination of airspace by very fine volcanic ash due to sequences of tran-sient ash plumes from Mount Etna. The atmospheric dispersal of sub-10 μm (PM10) ash is mod-elled using the WRF-Chem model coupled online with meteorology and aerosols and offline with Mass Eruption Rates (MER) derived from near-vent Doppler radar measurements and inferred plume altitudes. We analyse two sequences of paroxysms with widely varied volcanological conditions and contrasted meteorological synoptic patterns in October–December 2013 and on 3-5 December 2015. We analyse the PM10 ash dispersal simulation maps in terms of time-averaged columnar ash density, concentration at specified flight levels averaged over the entire sequence interval, and daily average concentration during selected paroxysm days at these flight levels. The very fine ash from such eruption sequences is shown to easily contaminate the airspace around the volcano within a radius of about 1000 km in a matter of a few days. Synoptic patterns with relatively weak tropospheric currents lead to the accumulation of PM10 ash at a re-gional scale all around Etna. In this context, closely interspersed paroxysms tend to accumulate very fine ash more diffusively in the lower troposphere and in stretched ash clouds higher up in the troposphere. Low-pressure, high-winds weather systems tend to stretch ash clouds into ~100 km-wide clouds forming large-scale vortices 800-1600 km in diameter. Daily average PM10 ash concentrations commonly exceed the aviation hazard threshold up to 1000 km downwind from the volcano and up to the upper troposphere for intense paroxysms. Vertical distributions show ash cloud thicknesses in the range 0.7–3 km, and PM10 sometimes stagnating at ground level, represent a potential health hazard.

In this note, I analyze the data generated by M. Fodje's (2013) simulation programs "epr-simple" and "epr-clocked". They were written in Python and published on Github. Inspection of the program descriptions shows that they make use of the detection-loophole and the coincidence-loophole respectively. I evaluate them with appropriate modified Bell-CHSH type inequalities: the Larsson detection-loophole adjusted CHSH, and the Larsson-Gill coincidence-loophole adjusted CHSH (NB: its correctness is conjecture, we do not have proof). The experimental efficiencies turn out to be approximately eta = 81% (close to optimal) and gamma = 55% (far from optimal). The observed values of CHSH are, as they should be, within the appropriately adjusted bounds. Fodjes' detection-loophole model turns out to be very, very close to Pearle's famous 1970 model, so the efficiency is close to optimal. The model has the same defect as Pearle's: the joint detection rates exhibit signaling. Fodje's coincidence-loophole model is actually a clever modification of his detection-loophole model. Because of this, however, it cannot lead to optimal efficiency.

The present study investigates the role of a simple inerter in supplemental devices for possible implementation in the matured seismic base isolation technique. Firstly, the response of the base-isolated structure with an optimally tuned mass damper-inerter (TMDI) is investigated to see the tuning effects. The time required to tune the TMDI was found to be significantly longer than the duration of a strong-motion earthquake. There was still a reduction in the response of the isolated structure, which is primarily due to the added damping and stiffness (ADAS) of TMDI and not because of the tuning effects. Hence, it is proposed that the corresponding ADAS of the TMDI be directly added to the isolation device. Secondly, the response of the base-isolated structures with the fluid inerter damper (FID) is studied. It was observed that the inerter of the FID does not influence the displacement variance of an isolated structure under broadband earthquake excitation. It implies that the response of the isolated structure with FID is primarily controlled by its counterpart fluid damper (FD). The performance of optimal TMDI, ADAS, FID, and FD to mitigate the seismic response of the flexible multi-story base-isolated structure under real earthquake excitations is also investigated. In terms of suppressing the displacement and acceleration responses of the isolated structure, it has been found that TMDI and ADAS perform similarly. Comparing the response of the isolated structure with FID and FD demonstrated that the inerter in the FID has detrimental effects on the isolated structures, in which the top floor's acceleration and base shear are substantially increased.

The environmental pollution by microplastics (MPs) has become a growing concern, and measures are being taken in many countries. Long-term and extensive MPs investigations involving not only professional researchers but also the citizenry are needed to understand the pollution situation and to confirm the decreasing trend of MPs pollution as a result of pollution control measures. In this study, the author evaluated the accuracy of a simple method of investigating MPs on sandy beaches that can be conducted even by high school students. In a land survey using such simple tools as a tape measure and cardboard, 70% of the deviations were within approximately 20 cm when multiple surveys of approximately 20 m distance were performed. Even without heavy liquid, 89% of MPs could be recovered using only seawater. An investigation of MPs content by sampling 0.5 cm of the surface layer of sand could explain more than half of the MPs content when the sand was sampled to a depth of approximately 50 cm below the surface layer. A method in which the recovered MPs are not visually sorted but floating matter after boiling is considered as MPs is acceptable. If there was no concern about pumice contamination, the overestimation was within approximately 1.5 times. Simple laboratory equipment such as buckets, sieves, seawater, hot plates, dryers, and electronic balances could achieve lower limits of quantification of MPs of 13 mg-MPs/m2-sand and 2 mg-MPs/kg-sand.

With an increasing amount of biological data available publicly, there is a need for a guide on how to successfully download and use this data. The Ten simple rules for using public biological data are: 1) use public data purposefully in your research, 2) evaluate data for your use case, 3) check data reuse requirements and embargoes, 4) be aware of ethics for data reuse, 5) plan for data storage and compute requirements, 6) know what you are downloading, 7) download programmatically and verify integrity, 8) properly cite data, 9) make reprocessed data and models Findable, Accessible, Interoperable, and Reusable (FAIR) and share, and 10) make pipelines and code FAIR and share. These rules are intended as a guide for researchers wanting to make use of available data and to increase data reuse and reproducibility.

Earth atmosphere is almost opaque in the infrared: about 374 W/m² is absorbed by the atmosphere out of 396 W/m² surface upward longwave radiation, and only about 22 W/m² leaves the system unabsorbed in the atmospheric window. This makes rise to the idea to approximate the annual global mean energy flow system from a simple idealized greenhouse model, where the surface is surrounded by a single-layer shortwave (SW) transparent, longwave (LW) opaque, non-turbulent atmosphere. The energy flows in this geometry can be described by elementary arithmetic relationships. Starting from this model, the realistic Earth’s atmosphere can be achieved by introducing partial atmospheric SW opacity, partial atmospheric LW transparency and turbulent fluxes during the course of the deduction. The resulted global mean energy flow system is then compared to several data sets such as satellite observations from the CERES mission; estimates using direct surface observations and climate models; global energy and water cycle assessments; and independent detailed clear-sky radiative transfer computations. We find that the deduction from this idealized model approximates the real values in Earth energy budget with reasonable accuracy: the deduced fluxes and the observed ones are consistent within the acknowledged error of observations; while fundamental features of the initial geometry like special ratios and definite relationships between the fluxes are preserved.

The first part of the paper was aimed at analyzing the given nonlinear problem by different methods of computation of the Lyapunov exponents (Wolf method [1], Rosenstein method [2], Kantz method [3], method based on the modification of a neural network [4, 5], and the synchronization method [6, 7]) for the classical problems governed by difference and differential equations (Hénon map [8], hyper-chaotic Hénon map [9], logistic map [10], Rössler attractor [11], Lorenz attractor [12]) and with the use of both Fourier spectra and Gauss wavelets [13]. It was shown that a modification of the neural network method [4, 5] makes it possible to compute a spectrum of Lyapunov exponents, and then to detect a transition of the system regular dynamics into chaos, hyper-chaos, hyper hyper-chaos and deep chaos [14-16]. Different algorithms for computation of Lyapunov exponents were validated by comparison with the known dynamical systems spectra of the Lyapunov exponents. The carried out analysis helps comparatively estimate the employed methods in order to choose the most suitable/optimal one to study different kinds of dynamical systems and different classes of problems in both this and the next paper parts.

The saturation properties of symmetric and asymmetric nuclear matter have been computed using the finite range simple effective interaction having Yukawa form-factor. The results of higher order derivatives of the energy per particle and the symmetry energy computed at saturation, namely, Q0, Ksym, Kτ, Qsym, are compared with the corresponding range of values extracted from studies involving theory, experiment and astrophysical observations. The ability of the equations of state computed with this simple effective interaction in predicting the threshold mass for prompt collapse in binary neutron star merger and gravitational redshift have been examined in terms of the compactness of the neutron star and the incompressibility at the central density of the maximum mass star. The correlations existing between neutron star properties with the nuclear matter saturation properties have been analyzed and compared with the predictions of other model calculations.

In this paper we provide an ``expository overview" of classic epidemic projection models. Starting with the simple case of an epidemic that grows exponentially we then investigate ``compartmental" models. These assume that the growth of an infected population is limited endogenously by the size of the underlying pool of susceptibles. We then describe a new family of so-called "Exo-r" statistical models, which hinge on an exogenously driven growth rate of the infected population. This family, which can be used to model both infections and deaths, captures parsimoniously both the depletion of susceptibles and the effect of interventions such as lockdowns and ``social distancing". The model is used to fit numbers of Covid-19 infections in China. It is also used to model and project deaths in the United States. Results are used to inform a discussion on i) the challenges at hand and ii) the extent to which epidemic projection models may be useful despite being wrong.

The Planning and implementation of construction projects are difficult processes and are burdened with many risk elements. The budget spread over time, which is developed on the basis of the schedule, presents the expected distribution of costs throughout the duration of the works, which during the implementation of the project is subject to constant changes resulting from time, cost and organizational factors. Managing construction contracts requires managers to be able to analyze on an ongoing basis the variances of production costs - from the values calculated in the offer cost estimate and assumed in the Budgeted Cost of Work Scheduled. The article attempts to analyze the emerging time and cost deviations using proprietary T/S and T/C monitoring, based on simple indicators of the EVM method. An example of construction of a multi-family housing development was used to study the variances of planned and incurred costs.

Accurate channel estimation is of utmost importance for massive MIMO systems that allow providing significant improvements in spectral and energy efficiency. In this work, we investigate the spectral efficiency performance and present a channel estimator for multi-cell massive MIMO systems subjected to pilot-contamination. The proposed channel estimator performs well under moderate to aggressive pilot contamination scenarios without prior knowledge of the inter-cell large-scale channel coefficients and noise power. The estimator approximates the performance of a linear Minimum Mean Square Error (MMSE) as the number of antennas increases. Following, we derive a lower bound closed-form spectral efficiency of the Maximum Ratio Combining (MRC) detector in the proposed channel estimator. The simulation results highlight that the proposed estimator performance approaches the linear minimum mean square error (LMMSE) channel estimator asymptotically.

With reference to Planck scale, increasing support for large scale cosmic anisotropy and preferred directions and by considering an increasing ratio of Hubble parameter to angular velocity, right from the beginning of Planck scale, we make an attempt to estimate ordinary matter density ratio, dark matter density ratio, mass, radius, temperature, age and expansion velocity (from and about the baby universe in all directions). We would like suggest that, from the beginning of Planck scale, 1) Dark matter can be considered as a kind of cosmic foam responsible for formation of galaxies. 2) Cosmic angular velocity decreases with square of the decreasing cosmic temperature. 3) Increasing ratio of Hubble parameter to angular velocity plays a crucial role in estimating increasing cosmic expansion velocity and decreasing density ratios of dark matter and ordinary matter. 4) There is no need to consider dark energy for understanding cosmic acceleration.

Forecasting streamflow accurately is essential to achieve an efficient integrated water resources management strategy and provide consistent support to water decision-makers. We present a simple, low-cost and robust approach for forecasting monthly and yearly streamflow during the hydrological year in course, applicable to headwater catchments. It combines the use of regression analysis techniques, the two-parameter Gamma continuous cumulative probability distribution function and the Monte Carlo method. It is based on a probabilistic comparison of the progression of the current hydrological year with the historic observed series. The methodology has been successfully applied to two headwater reservoirs within the Guadalquivir River Basin in southern Spain. The root-mean-square error and correlation coefficient were used to measure the accuracy of the model and the results showed good levels of reliability. The outputs are the probabilistic monthly and yearly streamflow and 80% confidence interval. Further reductions in prediction errors may be achieved from increasing the number of observed years. These risk-based predictions are of great value, especially, before the intensive irrigation campaign starts (usually in April), when Water Authorities are to take responsible management decisions about the best allocation of the available water volume between the different water users and environmental needs.

Physical activity (PA) is a modifiable factor that may have an influence on the course of Parkinson’s disease (PD). This study aimed to apply a simple behavioral intervention to encourage PD sufferers to increase their everyday physical activity and assess which parameters of motor functions will be improved. The research covered 50 PD patients (28 men and 22 women) aged 40-81 years (65.38 ± 9.23), with a duration of the disease 2-4 years, in stages 1-3 on the Hoehn and Yahr scale. The patients were randomly divided into two groups: the experimental group with behavioral therapy, and the control group without intervention. During 12 weeks the patients from the experimental group had five phone conversations. Each conversation lasted 15 minutes and was an interview about the subjects’ physical activity in the last month. The results were assessed by the Timed Up and Go test (TUG), Unified Parkinson's Disease Rating Scale (UPDRS) – part III, FIR (Functional Index “Repty” – own modification of Functional Independence Measure (FIM)), Functional Ambulation Category (FAC) and International Physical Activity Questionnaire (IPAQ). The results showed that spontaneous physical activity increased in the experimental group and motor functions improved. Physical activity improvement depended on age, body mass index, and gender.

Urban parks play a pivotal role in fostering the development of sustainable and smart cities, encompassing multifaceted dimensions of environmental, social, and economic significance. To effectively manage these urban parks, it is imperative to undertake an in-depth investigation of their environmental, social, and economic conditions, as well as their level of sustainability. However, there is currently a lack of readily applicable methodologies that comprehensively measure these benefits and provide a sustainability rating for urban parks. In this study, we propose a valuable tool that employs effective and affordable measures for the daily management of these green spaces. Our methodology is rooted in the three pillars of sustainability: environmental, social, and economic. Within these pillars, we have defined 19 indicators and 50 criteria, enabling a comprehensive assessment of park sustainability. This methodology is developed through the characterization and systematic documentation of the park’s day-to-day operations. To validate our methodology, we present a case study of Cárcamos Park, situated in the state of Guanajuato in Mexico, utilizing accurate operational data collected from January to December 2020. Through this real-life scenario, we demonstrate the high applicability and effectiveness of our methodology. The sustainability assessment of Cárcamos Park reveals a sustainability level of 57%, placing it within the medium sustainability range. Importantly, our methodology can also be incorporated during the design phase of new urban green spaces, offering flexibility and ease of application tailored to the unique characteristics of each park. Park managers can use our procedure and apply it to any park, evaluate their sustainability status and detect areas of opportunity. Our approach provides a comprehensive and practical tool for measuring and improving the sustainability of urban parks. Its simplicity and applicability make it accessible to anyone interested in creating a greener and more sustainable urban environment.

Notch signaling is a highly conserved pathway which occurs between adjacent cells to distinguish them. The Notch signaling cascade operates in a simple mechanism, yet Notch plays remarkably diverse roles in development to regulate cell fate determination, organ growth and tissue patterning. Originally isolated and characterized in the model insect Drosophila melanogaster, recent studies in various insect species have revealed that Notch signaling is broadly involved in the construction of insect tissues. This review focuses on providing a molecular mechanistic and developmental picture regarding the roles of Notch pathway in insects. The functions of Notch in the formation and patterning of insect embryo, wing, leg, ovary and several specific structures as well as in stress responses are summarized. These results are discussed in developmental context with an eye toward understanding the functionality of Notch signaling pathway in different insect species.

Bifidobacterium is the most beneficial flora of the human gastrointestinal tract, but there is a concentration threshold for Bifidobacterium to exert its beneficial properties. In this work, the effect of several simple culture methods on the number of viable bifidobacteria was discussed to improve its viable concentrations, and we unexpectedly discovered that bifidobacteria have inert growth. The concentration of viable bacteria of two isolated Bifidobacterium animalis subsp. lactis, BZ11 and BZ25 and Lactobacillus plantarum SQ-4 were investigated using solid-liquid-liquid circulation subculture, solid-liquid-liquid subculture and solid-liquid-liquid circulation subculture. These 3 subculture methods increase the viable cell concentration, and the best is the solid-liquid-liquid subculture. The highest concentrations of third-generation BZ11 and BZ25 were 9.62 × 109 CFU/mL and 1.21 × 1010 CFU/mL in order by solid-liquid-liquid subculture method, which was 10.38 times and 42.31 times higher (P<0.05) than those of the first generation, respectively. However, none of these three subculture methods increased the concentration of SQ-4. These results suggested that Bifidobacterium has growth inertia and Solid-liquid-liquid passage culture inhibiting the growth inertia. This finding is valuable in promoting the industrial application of probiotic bifidobacteria to potential probiotic food production.

This paper presents a simple model and explanation for the flat rotation curves of Spiral Galaxies without resorting to: (1) The introduction of Dark Matter, (2) a modification of Newton's 2nd law (MOND) or (3) a modification of Einstein's theory of General Relativity. The model that is developed involves a rotating baryonic disk (a rotating frame of reference with an "effective angular velocity" about its center surrounded by a rotating cloud of hydrogen (HI). The model also assumes that the measurements that are made on the rotating HI cloud are made from an earth based inertial frame of reference. The predictions of the model rely on the relationship between velocities as measured by earth based radio telescopes and the velocities as measured in the rotating frame. Calculations of the rotation curves of three galaxies are made using this model and compared with readily available experimental data

In response to the increasing energy demand in Taiwan and the global trend of renewable energy development, Kuroshio energy is a potential energy source. How to extract this invaluable natural resource has then become an intriguing and important question in engineering practices. This study conducted a study for a nozzle-diffuser duct (NDD) as the Kuroshio currents energy harvester. The computational fluid dynamics (CFD) software ANSYS Fluent was employed to calculate the drag and added mass coefficients of the duct anchored to the seabed. Those coefficients were further imported into Orcaflex to simulate the motion of the duct under normal and storm wave conditions. Results showed that the duct was stable 25 m below the sea surface under normal wave condition. When the wave condition changed to storm waves, the duct needed to dive into at least 90 m below the sea surface to regain its stability and obtain high power take-off (PTO). An optimal design nozzle-diffuser-duct was reported and a PTO peak of 15 kW was expectable in the Kuroshio currents. Once a suitable offshore platform can be developed with sixty-six NDDs, a Megawatt Kuroshio ocean current power generation system is feasible in the near future.

Multi-criteria decision-making (MCDM) methods and techniques have been applied to many real-world problems in different fields of engineering science and technology. The evaluation based on distance from average solution (EDAS) method is a new and efficient MCDM method. The aim of this study is to propose a modification to address two exceptional cases in which the EDAS method fails to solve an MCDM problem.

Fired bricks have shown tremendous potential as a construction material due to their properties. However, their use required some specifications in terms of quality, resistance, and durability. In developing countries, the lack of tools to make test specimens leads to many defects in these brick specimens responsible for low durability and weak precision during mechanical tests and shrinkage. In this study, a simple and traditional method of making test bricks is presented. This simple method allows the production of bricks with the required properties. This method is especially efficient for a firm or semi-soft pastes consistency. The handmade pastes do not stick into the walls of the mold like the case of steel molds and it gives specimens with standard shape, smooth surface, and sharp edges. The resulting fired bricks exhibit high mechanical strength comparable and even better than those of conventional methods.

Based on a previous risk calculation study along a road corridor, risk is recalculated using stochastic simulation by introducing variability for most of the parameters in the risk equation. This leads to an exceedance curve comparable to that of catastrophe models. This approach introduces uncertainty into the risk calculation in a simple way, which can be used for poorly documented cases to fulfil lack of data. This approach seems to tend to minimize risk or to question risk calculations.

We present a cost- and time-efficient method for the controlled preparation of single phase La(IO3)3 nanoparticles via a simple soft-chemical route which takes a matter of hours, thereby providing an alternative to the common hydrothermal method which takes days. Nanoparticles of pure α-La(IO3)3 and pure δ-La(IO3)3 were synthesised via the new method depending on the source of iodate ions, thereby demonstrating the versatility of the synthesis route. The crystal structure, nanoparticle size-dispersal and chemical composition were characterised via angle- and energy-dispersive powder X-ray diffraction, scanning electron microscopy and Fourier-transform infrared spectroscopy.

The effects of an external strain tensor on the electrical resistivity of a manganite granular system are investigated using a simple approach describing the induced deformation in terms of the tilt angle between adjacent grains. The results obtained assuming the resistivity of each grain as given by a metallic part, coming from the inner grain, and a surface related tunnel contribution, allow to estimate appreciable resistivity variations even in the case of small deformation angles.

Tidal stream energy, due to its high level of consistency and predictability, is one of the feasible and promising type of renewable energy for future development and investment. Applicability of Blade Element Momentum (BEM) method for modeling the interaction of turbines in tidal arrays has been proven in many studies. Apart from its well-known capabilities, yet there is scarcity of research using BEM for the modeling of tidal stream energy farms considering full scale rotors. In this paper, a real geographical site for developing a tidal farm in the southern coasts of Iran is selected. Then, a numerical methodology is validated and calibrated for the selected farm by analyzing array of turbines. A linear equation is proposed to calculate tidal power of marine hydrokinetic turbines. This methodology narrows down the wide range of turbine array configurations, reduces the cost of optimization and focuses on estimating best turbine arrangements in a limited number of positions.

Topographic mapping using stereo plotting is not effective because it takes much time and labor-intensive. Thus, this research was conducted to find the effective way to extract building footprint for mapping acceleration. Building extraction method in this process comprises four steps: ground / non-ground filtering, building classification, segmentation, and building extraction. Non-ground points from filtering process were classified as building with the algorithm based on multi-scale local dimensionality to separate points at the maximum separability plane. Segmentation using segment growing was used to separate each building, so edge detection could be conducted for each segment to create boundary of each building. Lastly, building extraction was conducted through three steps: edge points detection, building delineation, and building regularization. With 10 samples and step 0.5, classification resulted quality and miss factor of 0.597 and 0.524, respectively. The quality was improved by segmentation process to 0.604, while miss factor was getting worse to 0.561. Meanwhile, on average shape index value from extracted building had 0.02 difference and the number of errors was 30% for line segment comparison. Regarding positional accuracy using centroid accuracy assessment, this method could produce RMSE of 1.169 meters.

After conducting a detailed survey among the villagers of Pallissery and Karukutty, it was observed that in most of the villages the native people have to travel long distances for their basic health needs. Also most of the villagers lack knowledge regarding live health updates. At times, these problems have even resulted in death of many people including pregnant women and children. The objective of our research is to propose an integrated and easy to use Medical Kiosk that can be installed at various locations in rural areas. The Kiosk will provide an integrated environment for all medical related activities and would perform numerous functions like sending notifications regarding medical camps, mobile medical help, important dates for vaccinations, child care, insurance policies and provide other live medical updates to the villagers. It would also support the basic facilities for measurement of body parameters like height, weight, BMI, blood pressure, and heartbeat and also facilitate live consultation facilities with specialized doctors through video and voice chats.

The creation of hydrophobic, antifreeze and self-cleaning coatings is currently being pursued by many industrial sectors. The potential applications include the production of liquid and gas separators and filters, new materials, optical and microelectronic devices, and textiles and clothing. These coatings will also have wide application in the construction and automobile industries, shipping, and energy and agricultural sectors. The article proposes a simple approach to the creation of superhydrophobic and antifreeze coatings, by applying powder from multi-walled carbon nanotubes (MW-CNTs) to the sample surface. This method enables combination of the necessary factors: low surface energy, micro–nano-roughness and hierarchical multi-scale. The authors investigated the dependence of the wetting angle of such a surface on the time, type and degree of functionalization. The electrophysical properties of modified MW-CNTs were studied over wide frequency and temperature ranges. This method of obtaining hydrophobic coatings differs from currently available methods in that it is simpler to prepare, is of lower cost and has less environmental impact. The proposed approach can be used to create superhydrophobic coatings that have the additional function of removing static charge and therefore reducing surface heating, and which can be used in the field of energetics for protection against the freezing of wind turbine blades and aircraft surfaces.

Despite copious research, the methods for assessing upper- and lower-limb motor coordination are limited. We devised a simplified evaluation method based on upper- and lower-limb motor coordination jumping and conducted a practical examination of the characteristics of the motion and applicability of the evaluation method. Overall, 88 high-school athletes with comparable competitive abilities were included in this study. The participants were divided into two groups based on their prior experience with motor coordination training (24 in the experienced group; 64 in the inexperienced group). First, a population proportion test was employed to assess the success rate of the four upper- and lower-limb motions in each task. This revealed significant difference between all tasks, except for the fourth motion, indicating that different motions have varying degrees of difficulty and that the combination of motions with differing difficulty coefficients can result in the creation of entirely new tasks with varying degrees of difficulty. Second, the experienced group demonstrated significantly superior performance compared to the inexperienced group by a t-test. These results confirmed that athletes (with the same level of competitive ability) trained in upper and lower limb motor coordination were able to excel in this evaluation method, confirming its validity.

We introduce a magnetic bead-based sample preparation scheme for enabling a Raman spectroscopic differentiation of severe acute respiratory syndrome coronavirus type 2 (SARS-CoV-2) positive and negative samples. The beads were functionalized with the angiotensin-converting enzyme 2 (ACE2) receptor protein, which is used as recognition element to selectively enrich SARS-CoV-2 on the surface of the magnetic beads. Subsequent Raman measurements directly enable discriminating SARS-CoV-2 positive and negative samples. The proposed approach is applicable for other virus species, too, when the specific recognition element is exchanged. Series of Raman spectra were measured on three types of samples, namely SARS-CoV-2, Influenza A H1N1 virus and a negative control. For each sample type, eight independent replicates were considered. All spectra are dominated by the magnetic bead substrate and no obvious differences between sample types are apparent. In order to address the subtle differences in the spectra, we calculated different correlation coefficients, namely the Pearson coefficient and the Normalized Cross Correlation coefficient. By comparing the correlation with the negative control differentiating between SARS-CoV-2 and Influenza A virus is possible. This study provides a first step towards the detection and potential classification of different viruses with the use of conventional Raman spectroscopy.

Paper-based analytical devices have been substantially developed in recent decades. Many fabrication techniques for paper-based analytical devices have been demonstrated and reported. Herein we report a relatively rapid, simple, and inexpensive method for fabricating paper-based analytical devices using parafilm hot pressing. We studied and optimized the effect of the key fabrication parameters, namely pressure, temperature, and pressing time. We discerned the optimal conditions, including pressure of 3.8 MPa (3 tons), temperature of 80oC, and 3 minutes of pressing time, with the smallest hydrophobic barrier size (821 µm) being governed by laminate mask and parafilm dispersal from pressure and heat. Physical and biochemical properties were evaluated to substantiate the paper functionality for analytical devices. Wicking speed in the fabricated paper strips was slightly slower than that of non-processed paper, resulting from reducing paper pore size. A colorimetric immunological assay was performed to demonstrate the protein binding capacity of the paper-based device after exposure to pressure and heat from the fabrication. Moreover, mixing in two-dimensional paper-based device and flowing in a three-dimensional counterpart were thoroughly investigated, demonstrating that the paper device from this fabrication process is potentially applicable as analytical devices for biomolecule detection. Fast, easy, and inexpensive parafilm hot press fabrication presents an opportunity for researchers to develop paper-based analytical devices in resource-limited environments.

A convenient practical model for accurately estimating the total entropy (ΣSi) of atmospheric gases based on physical action is proposed. This realistic approach is fully consistent with statistical mechanics, but reinterprets its partition functions as measures of translational, rotational and vibrational action or quantum states, to estimate the entropy. With all kinds of molecular action expressed as logarithmic functions, the total heat required for warming a chemical system from 0o K (ΣSiT) to a given temperature and pressure can be computed, yielding results identical with published experimental third law values of entropy. All thermodynamic properties of gases including entropy, enthalpy, Gibbs energy and Helmholtz energy are directly estimated using simple algorithms based on simple molecular and physical properties, without resource to tables of standard values; both free energies are measures of quantum field states and of minimal statistical degeneracy, decreasing with temperature and declining density. We propose that this more realistic approach has heuristic value for thermodynamic computation of atmospheric profiles, based on steady state heat flows equilibrating with gravity. Potentially, this application of an action principle can provide better understanding of emergent properties of many natural or evolving complex systems, including modelling of predictions for global warming.

This study aims to refine our understanding of evolutionary processes, particularly as they apply to complex organisms, using an innovative graph-based simulation approach. We model the topological evolution of simple (5-node ring graph) and complex (20-node dense random graph) organisms over 10 generations, applying different mutation rates to reflect biological realities. Our results provide intriguing insights into the potentially different evolutionary dynamics at play in simple versus complex organisms. While simple organisms demonstrate high topological flexibility and rapid adaptability, aligning with classical evolutionary models, complex organisms exhibit a surprising degree of structural stability. This stability persists even under mutation rates that would typically drive significant changes in simpler systems. The simulation highlights an important consideration: the intricate, interdependent networks characteristic of complex organisms may create a form of evolutionary buffering. This buffering could modulate the impact of random mutations and natural selection – processes that are cornerstones of evolutionary theory. Our findings suggest that the high degree of complexity in advanced life forms may necessitate a more nuanced view of how evolutionary processes operate across different levels of biological organization. Furthermore, the emergence of new structural motifs in simple organisms, contrasted with the relative conservation in complex topologies, indicates that evolutionary mechanisms may manifest differently across the spectrum of biological complexity. This observation invites a more detailed exploration of how evolutionary principles apply to diverse life forms.These results contribute to the ongoing refinement of evolutionary theory, especially in its application to complex organisms. They suggest that additional mechanisms, such as constrained mutations, epigenetic changes, or higher-order organizational principles, may play significant roles alongside random mutations and natural selection in the evolution of complex life forms.

Background: Olecranon fractures are common injuries of the upper limb in adults. Simple dis-placed trasverse fractures are generally surgically treated with tension-band wiring (TBW) or plate fixation (PF). The purpose of this retrospective study is to compare the clinical-functional outcome, complications and reoperation rates between TBW and PF for Mayo IIA fractures. Methods: 72 patients treated with PF or TBW at our institution, completed our survey and clinical evaluation and their demographic and clinical data were recorded and analysed. The clini-cal-functional outcomes were evaluated assessing ROMs and three validated scoring systems: the Disabilities of the Arm, Shoulder, and Hand (DASH), the Mayo Elbow Performance Score (MEPS) and the Patient American Shoulder and Elbow Surgeons Standardized Elbow Assess-ment score (pASES-e). Results: 38 patients (53%) underwent TBW and 34 (47%) PF. The mean DASH, MEPS and pASES-e scores were respectively 14.5±17.2, 80.5±14.7 and 83.6±12.4 in the TBW group and 21±21.7, 75.6±15.3 and 75.1±19.2 in the PF group (p=0.16, p=0.17 and p=0.03). The mean duration of surgery and hospitalisation period were longer in the PF group (p=0.002, p=0.37) whereas the complication and reoperation rates were higher after TBW (p=0.15, p=0.24). Conclusion: According to the literature, both TBW and PF resulted comparable valid surgical op-tions for the treatment of simple isolated displaced olecranon fractures, revealing that they both provide good/excellent outcomes with no significant differences.

Kolmogorov–Arnold Network (KAN) is an emerging interpretable neural network compared to fully black-box MLPs. Recently, emerging works focus on comprehensive and fair comparisons between KAN and MLP in various tasks. However, these works didn't focus on the strongest advantage of KAN: generating symbolic outputs. The ability of KAN to provide scientific insights or even discover new science is under-examined. In this work, we propose several novel metrics to measure how well a KAN performs on symbolic function fitting: R^2-Mean, weighted R^2-complexity loss, and ranking metrics. We also propose a metric to determine mathematical complexity of a target function and evaluate KAN with several functions of different mathematical complexity. Additionally, we also tried inputs with different ranges to find the effect of normalization.

In South Korea, demolition waste (DW) management has become increasingly significant owing to the rising number of old buildings. Effective DW management requires an efficient approach that accurately quantifies and predicts the generation of DW (DWG) of various types, which necessitates access to the required information or technology capable of achieving this. Hence, we developed an artificial intelligence-based model that predicts the generation of ten DW types, specifically from buildings in redevelopment areas. We used an artificial neural network algorithm with < 10 neurons in the hidden layer to derive individual input variables and optimal hyperparameters for each DW type. All DWG prediction models achieved an average validation and test prediction performance (R²) of 0.970 and 0.952, respectively, with their ratios of percent deviation ≥ 2.5, ver-ifying them as excellent models. Moreover, a Shapley additive explanations analysis revealed that DWG was most impacted by the floor area for all the DW types, with a positive correlation with DWG. Conversely, other factors showed either a positive or negative correlation with DWG de-pending on the DW type. The study findings will enable demolition companies and local gov-ernments in making informed decisions for efficient DW management and resource allocation by accurately predicting the generation of various types of DW.

Emerging infectious disease threats require rapid response tools to inform diagnostics, treatment, and outbreak control. RNA-based metagenomics offers this; however, most approaches are time-consuming and laborious. Here, we present a simple and fast protocol – the RAPIDprep assay – with the aim to provide cause agnostic laboratory diagnosis of infection within 24 hours of sample collection by sequencing ribosomal RNA-depleted total RNA. The method is based on the synthesis and amplification of double-stranded cDNA followed by short-read sequencing with minimal handling and clean-up steps to improve processing time. The approach was optimized and applied to a range of clinical respiratory samples to demonstrate diagnostic and quantitative performance. Our results showed robust depletion of both human and microbial rRNA, and library amplification across different sample types, qualities and extraction kits using a single protocol without input nucleic acid quantification or quality assessment. Furthermore, we demonstrate the genomic yield of both known and undiagnosed pathogens with complete genomes recovered in most cases to inform molecular epidemiological investigations and vaccine design. The RAPIDprep assay is a simple and effective tool, and representative of an important shift towards integration of modern genomic techniques to infectious disease investigations.

Rapid development of high-throughput omics technologies generates an increasing interests in algorithms for cutoff point identification. Existing cutoff methods and tools identify cutoff points based on association of continuous variables with another variable, such as phenotype, disease state or treatment group. These approaches are not applicable for descriptive studies in which continuous variables are reported without known association with any biologically meaningful variables. The most common shape of the ranked distribution of continuous variables in high-throughput descriptive studies corresponds to a biphasic exponential/super-exponential curve, where the first phase includes big number of variables with values slowly growing with rank and the second phase includes smaller number of variables rapidly growing with rank. This study describes an easy algorithm to identify the boundary between these phases to be used as a cutoff point. The major assumption of that approach is that small number of variables with high values dominate biological system and determine its major processes and functions. This approach was tested on three different datasets: genes in the human cerebral cortex, mammalian genes sensitive to chemical exposures, and proteins expressed in human heart. In every case, the described cutoff identification method produced shortlists of variables (genes, proteins) highly relevant for dominant functions/pathways of the analyzed biological systems. Thus, our described method for cutoff identification may be used to prioritize variables for a focused functional analysis, in situations where other methods of dichotomization of data are inaccessible.

Additive manufacturing (AM) is a promising new technology that is having a very fast growth from home workshops to high-tech cutting-edge factories. As any manufacturing technique, adequate metrology services are needed to assure the quality of items manufactured by AM. One of the most widely used instruments to measure the characteristics of surfaces manufactured with AM is the confocal microscope. In this paper, authors present a whole calibration procedure for confocal microscopes designed to be implemented preferably in workshops or industrial environments rather than in research and development departments. Because of that, it is as simple as possible. The procedure is designed without forgetting any of the key aspects that need to be taken into account and based on classical reference material standards. These standards can be easily found in industrial dimensional laboratories and easily calibrated in accredited calibration laboratories.

Obesity represents a worldwide epidemic disorder, increasing the overall morbidity and mortality rate. In this study we investigated the impact of obesity on peri-operative and long-term functional outcomes of Robotic assisted simple prostatectomy (RASP). Baseline flowmetry parameters and validated questionnaires’ scores were prospectively recorded. Follow-up assessments included Flowmetry and validated questionnaires. Composite outcomes (Trifecta) was defined as combination of: post-operative Q-max>15 ml/sec, IPSS score<8 and absence of complications. Pentafecta included also post-operative ejaculation persistence (MSHQ score>0) and the Erectile function maintenance (∆IEEF<6). Data were stratified by BMI (<30 or ≥30). 81 patients underwent RASP in our Institution. Baseline demographics and clinical features, questionnaires score and baseline flowmetry results were comparable between obese and non-obese cohorts. At follow-up, obese patients reported lower subjective improvement in IPSS (p=0.02) and OABQ scores (p<0.001) and higher incidence of stress incontinence requiring Duloxetin (p<0.001). Flowmetry outcomes, were also worse in this cohort (p=0.02 and p=0.03, respectively). At comprehensive outcomes assessment, obese patients had comparable Trifecta (67% vs 54%, p=0.39) and pentafecta achievement rate (p=0.76). Our prelimirary results proved that obesity is associated with worse functional outcomes (storage LUTS and incontinence rate) after RASP, but doesn’t affect trifecta and pentafecta achievement rate.

Data from ocean color (OC) remote sensing are considered a cost-effective tool for the study of biogeochemical processes globally. Satellite-derived chlorophyll, for instance, is considered an Essential Climate Variable since it is helpful in detecting climate change impacts. Google Earth Engine (GEE) is a planetary scale tool for remote sensing data analysis. Along with OC data, such tools allow an unprecedented spatial and temporal scale analysis of water quality monitoring in a way that has never been done before. Although OC data have been routinely collected at medium (~1 km) and more recently at high (~250 m) spatial resolution, only coarse resolution (≥4 km) data are available in GEE, making them unattractive for applications in the coastal regions. Data reprojection is needed prior to making OC data readily available in the GEE. In this paper, we introduce a simple but practical procedure to reproject and ingest OC data into GEE. The procedure is applicable to OC swath (Level-2) data and is easily adaptable to higher-level products. The results showed consistent distributions between swath and reprojected data, building confidence in the introduced framework. The study aims to start a discussion on making high resolution OC data readily available in GEE.

Based on comprehensible non-parametric methods, estimates of crucial parameters that characterise the COVID-19 pandemic with a focus on the German epidemic are presented. Where appropriate, the estimates for Germany are compared with the results for seven other countries (FR, IT, US, UK, ES, CH, BR) to get an idea of the breadth of applicability and a relational understanding. Thereby, only prevalence data of daily reported new counts of diagnosed cases and fatalities provided by the Johns Hopkins University are used. Drawing on uncertain a priori knowledge is avoided. Specifically, we present estimates resulting from delay-time correlations for the duration from diagnosis to death being 13 days for Germany and Switzerland. The delay-time correlation applied to time series from other countries exhibit less pronounced peaks suggesting high variabilities for the corresponding time-to-death durations. With respect to the German data, the two time series of new cases and fatalities exhibit a strong coherence within the frequency range of interest, which backs our findings. Furthermore, based on the knowledge of this time lag between diagnoses and deaths, properly delayed asymptotic as well as instantaneous fatality-case ratios are calculated having superiority compared to the commonly published case-fatality rate. The temporal median of the instantaneous fatality-case ratio with proper delay of 13-days between cases and deaths for Germany turns out to be 0.02. Time courses of asymptotic fatality-case ratios are presented for other countries which substantially differ during the first half of the pandemic, however, converge to a narrow range with standard deviation 0.57% and mean 2.4%. Additionally, the time courses of instantaneous fatality-case ratios with optimal delay for the 8 exemplarily chosen countries are calculated and compared by means of the temporal medians. Similarly to the asymptotic fatality-case ratios, the differences are much smaller than expected from mass media reports. The basic reproduction number, R₀, for Germany is estimated to be between 2.4 and 3.4. The uncertainty stems from uncertain knowledge of the generation time. A delay autocorrelation shows resonances at about 4 days and 7 days, where the latter resonance is at least partially attributable to the sampling process with weekly periodicity. The calculation of the basic reproduction number is based on an evaluation of cumulative numbers of cases yielding time-dependent doubling times as an intermediate step. This allows to infer to the reproduction number during the early phase of onset of the epidemic. In a second approach, the instantaneous reproduction number is derived from the incident (counts of new) cases and allows, in contrast to the first version, to infer to the temporal behaviour of the reproduction number during the later epidemic course. The time course of the reproduction number is compared to an alternative control measure given by the per capita growth, which largely confirms the conclusions drawn from the reproduction number. To conclude, by avoiding complicated parametric models we provide insights into basic features of the COVID-19 epidemic in an utmost transparent and comprehensible way. The perhaps most striking insight is that the fatality-case ratios do not differ between countries as much as previously suspected.

As part of a plethora of global efforts to minimize the negative effects of the SARS-CoV2 (COVID-19) pandemic, we developed two different mechanisms that, after further development, could potentially be of use in the future in order to increase the capacity of ventilators with low-cost devices based on single-use-bag-valve mask systems. We describe the concept behind the devices and report a characterization of them. Finally, we make a description of the solved and unsolved challenges and propose a series of measures in order to better cope with future contingencies.

COVID-19 infection, caused by SARS-CoV-2, is inequitably distributed and more lethal among populations with lower socioeconomic status. Direct contact with contaminated surfaces has been one of the virus sources, as it remains infective up to days. Several disinfectants have been shown to inactivate SARS-CoV-2 but they rapidly evaporate, are flammable or toxic and may be scarce or inexistent for the vulnerable populations. Therefore, we are proposing a simple, easy to prepare, low-cost and efficient antiviral films, made with wide available dishwasher detergent, which can be spread in hands and inanimate surfaces and maintains virucidal activity for longer periods than the current sanitizers. Avian coronavirus (ACoV) was used as model of challenge to test the antivirus efficacy of proposed films. Polystyrene microplates were covered with a thin layer of detergent formula. After drying, the films were exposed to different virus doses for 10 minutes and virus infectivity were determined using embryonated chicken eggs and RNA virus quantification in allantoic fluids by RT-qPCR. The films showed to inactive the ACoV (ranging from 103.66 to 106.66 EID50), which is chemically and morphologically similar to SARSCoV-2 and may constitute an excellent alternative to minimize the spread of Covid-19.

A construction for the systems of natural and real numbers is presented in Zermelo-Fraenkel Set Thoery, that allows for simple proofs of the properties of these systems, and practical and mathematical applications. A practical application is discussed, in the form of a Simple and Linear Fast Adder (Patent Pending). Applications to finite group theory and analysis are also presented. A method is illustrated for finding the automorphisms of any finite group $G$, which consists of defining a canonical block form for finite groups. Examples are given, to illustrate the procedure for finding all groups of $n$ elements along with their automorphisms. The canonical block form of the symmetry group $\Delta_4$ is provided along with its automorphisms. The construction of natural numbers is naturally generalized to provide a simple and sound construction of the continuum with order and addition properties, and where a real number is an infinite set of natural numbers. A basic outline of analysis is proposed with a fast derivative algorithm. Under this representation, a countable sequence of real numbers is represented by a single real number. Furthermore, an infinite $\infty\times\infty$ real-valued matrix is represented with a single real number. A real function is represented by a set of real numbers, and a countable sequence of real functions is also represented by a set of real numbers. In general, mathematical objects can be represented using the smallest possible data type and these representations are calculable. In the last section, mathematical objects of all types are well assigned to tree structures in a proposed type hierarchy.

Crystal structures of simple metals and binary alloy phases based on the face-centered cubic (fcc) structure are analyzed within the model of Fermi sphere – Brillouin zone interactions to understand the stability of original cubic structure and derivative structures with distortions, superlattices and vacancies. Examination of the Brillouin-Jones configuration in relation to the nearly-free electron Fermi sphere for several representative phases reveals significance of the electron energy contribution to the phase stability. Representation of complex structures in the reciprocal space clarifies their relationship to the basic cubic cell.

A 3D graphene foam made of interconnected multilayer graphene flakes was produced on optical fibres (OF) by laser-induced transformation of a polyimide (PI) film coated on the OF cladding. This material, known as la-ser-induced graphene (LIG), was explored in the electrochemical detection and quantification of dopamine (DA) at physiologically relevant concentrations in the presence of the most relevant interfering molecules in biological fluids, ascorbic acid (AA) and uric acid (UA). The measured limit of detection is 100 nM, the linear range is 0.1 to 5 μM and a maximum sensitivity of 5.0 µA µM−1 cm−2 was obtained for LIG decorated with Pt nanoparticles (NPs). Moreover, immunity to AA and UA interference and to fouling was attained by decorating the LIG elec-trode with Pt NPs and coating with Nafion. These figures of merit underlines the potential of these sensors for the quantification of physiologically relevant concentrations of DA in biological fluids, paving the way for the development of hybrid electrochemical/optical sensing actuating platforms in a lab-on-fibre configuration, with relevant applications in biomedical engineering. The advantages of this hybrid arrangement include the possi-bility of in-situ counterproofing, extended measuring ranges, photoelectrochemical detection and the probing of inaccessible places. This elegant approach can also provide a simple and cost-effective way to fabricate biomed-ical devices with extended functionality, such as medical optical probes with added electrochemical capabilities, optogenetics combined with local electrochemical detection, among others.

This article presents a novel computational approach to visualizing memristor dynamics within a simulated neural network. Memristors, known for their ability to emulate synaptic plasticity due to their variable resistance characteristics, are key components in neuromorphic computing and hold potential for advancing our understanding of neural processes. Our study introduces a sophisticated memristor model that incorporates non-linear resistance changes, simulating the complex behavior of synaptic connections in a neural network.The neural network, consisting of multiple interconnected neurons with memristor-based synapses, is subjected to a series of electrical stimuli. Each memristor's resistance is modulated in response to the applied voltage, mimicking the synaptic weight adjustments that occur during learning and memory formation in biological neural networks. To effectively illustrate these changes, we employ a high-contrast color mapping scheme, where the varying resistance of each memristor is represented by distinct colors, providing a clear and intuitive visualization of synaptic modifications over time.Our simulation runs through multiple iterations, demonstrating how synaptic weights evolve in response to different input patterns. The use of an extended voltage range and increased scaling factors ensures pronounced changes in memristance, enhancing the visibility of synaptic adaptations. The resulting visualizations offer a compelling representation of how memristors can mimic the dynamic nature of biological synapses, contributing to the field of neuromorphic engineering and deepening our comprehension of neural mechanisms underlying learning and memory.This work not only showcases the potential of memristors in simulating neural behavior but also provides a valuable educational tool for illustrating complex concepts in neuroscience and neuromorphic computing. The insights gained from this study pave the way for further exploration into the development of advanced neural network models and the design of memristor-based computing systems.

Existing reinforced concrete buildings with seismically-deficient column details affect the overall behavior depending on the failure type of column. The purpose of this study is to develop and validate a machine learning-based prediction model for the column failure modes (shear, flexure-shear and flexure failure modes). For this purpose, artificial neural network (ANN), K-nearest neighbor (KNN), decision tree (DT), and random forest (RF) models were used considering previously-collected experimental data. Using four machine learning methodologies, we developed a classification learning model that can predict the column failure modes in terms of the input variables using concrete compressive strength, steel yield strength, axial load ratio, height-to-dept aspect ratio, longitudinal reinforcement ratio, and transverse reinforcement ratio. The performance of each machine learning model was compared and verified by calculating accuracy, precision, recall, F1-Score, and ROC. Based on the performance measurements of the classification model, the RF model represents the highest average value of the classification model performance measurements among the considered learning methods, and it can conservatively predict the shear failure mode. Thus, the RF model can rapidly predict the column failure modes with the simple column details. Additionally, it was demonstrated that the predicted failure modes from the selected model were exactly same as the failure mode determined from a code-defined equation (traditional method)

Bees have long been used as a bioindicator of environmental quality. They have the capacity to bio-accumulate various pollutants in cities such as PAHs and heavy metals, but they are also very sensitive to other pollutants in rural areas such as pesticides. The lethal and sub-lethal impacts of pesticides on bees have been extensively studied. However, studies often focus on a single molecule at a same time and rarely on a cocktail of pesticides. The oxidant stress in response to metals and NOx was also measure, but no studies were engaged on the impact of PAHs on honeybees. The aim of this study was to measure the oxidative stress in bees in response to the chronic ingestion of a mixture of pesticides (representative of pollutants in rural areas) on the first hand and a mixture of PAHs (representative of pollutants in urban areas) on the other hand, compared to a control group. We also wanted to determine whether this tool is effective in detecting environmental measures aimed at reducing pollution in urban and rural areas.