At the highest level of endurance sports, the differences in finishing times are small, so equipment is constantly being constantly improved to enhance the athletes' performance. For instance, one dominant resistive force in connection with cross-country skiing is the friction between the skis and snow and since the 1930s, research designed to understand and reduce this friction has been ongoing. The mechanisms involved in ski-snow friction include compaction, micro-ploughing, adhesion, viscosity, and water-bridging. Of these, adhesive and viscous friction have been most studied, while much less is presently known about compaction, micro-ploughing, and water-bridging. At the macro-scale, the ski-camber profile plays a key role in determining whether, with respect to friction, a particular cross-country ski is suitable for use under a given set of conditions. Through its influence on where ski-snow contact occurs, this ski-camber profile has a profound impact on adhesive and viscous friction, micro-ploughing, the formation of water bridges, and the rate of compaction. Different contact zones with different apparent areas of contact and pressure have been found to be most suitable for different conditions. In addition, the micro-scale texture of the ski base is also an important determinant of ski-snow friction. Topographical measurements of this texture can be achieved with white-light interferometer and recent characterisation has focused on the mechanical properties of contact. In numerous tribological studies the interactions between features at different scales are modelled. In most tribological systems, features on several scales influence friction and ski-snow contact is certainly no exception. Accordingly, the current investigation was designed to evaluate the multi-scale properties of different combinations of two skis with two different base textures. The real area of contact and the average interfacial separation and total average reciprocal interfacial separation between the ski and snow were taken into consideration. We found that different macro- and micro-scale properties of the ski favour different mechanisms of friction. Both the profile of the ski camber and texture of the base play decisive roles in determining viscous friction. At the same time, the texture of the ski base exerts a greater impact on the average real contact pressure, real contact area and minimal average interfacial separation between the ski and snow than does the ski-camber profile.

In winter sports, the equipment often comes into contact with snow or ice, and this contact generates a force that resists motion. In some sports, such as cross-country skiing, this resistive force can significantly affect the outcome of a race, as a small reduction in this force can give an athlete an advantage. Researchers have examined the contact between skis and snow in detail, and to fully understand this friction, the entire ski must be studied at various scales. At the macro scale, the entire geometry of the ski is considered and the apparent contact between the ski and the snow is considered and at the micro scale the contact between the snow and the ski base ski-base textures. In the present work, a method for characterising contact between the ski-base texture and virtual snow will be presented. Six different ski-base textures will be considered. Five of them are stone-ground ski bases, and three of them have linear longitudinal textures with a varying number of lines and peak-to-valley height, and the other two are factory-ground “universal” ski bases. The sixth ski base has been fabricated by a steel-scraping procedure. In general, the results show that a ski base texture with a higher Spk-value has less real contact area, and that the mutual differences can be large for surfaces with similar Sa-values. The average interfacial separation is, in general, correlated with the Sa-value, where a “rougher” surface exhibits a larger average interfacial separation. The results for the reciprocal average interfacial separation, which is related to the Couette type of viscous friction, were in line with the general consensus that a “rougher” texture performs better at high speed than a “smoother” one, and it was found that a texture with high Sa and Spk values resulted in a low reciprocal average interfacial separation and consequently low viscous friction. The reciprocal average interfacial separation was found to increase with increasing real contact area, indicating a correlation between the real area of contact and the Couette part of viscous friction.

(S)-Atenolol ((S)-2-(4-(2-Hydroxy-3-(isopropylamino)propoxy)phenyl)acetamide) has been synthesized in >99% ee with use of Candida antarctica lipase B from Syncozymes (Shanghai, China), in a kinetic resolution of the corresponding racemic chlorohydrin. Deprotonation of the starting phenol building block was base catalyzed. The enantiopurity of the chlorohydrin building block remained unchanged upon subsequent amination. All four steps in the synthesis protocol have been optimized compared to previously reported methods, which makes this new protocol more sustainable and in accordance with green chemistry principles compared to previously reported protocols.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

Background: In this study, we aimed to evaluate the effect of s-FLT-1 and PlGF concentrations in women in the first trimester of pregnancy on the pulsatility index of the ductus venosus and the right and left uterine arteries. Methods: A total of 108 pregnant women in their first trimester were included in the study, with 87 assigned to the experimental group and 21 to the control group. Ultrasound examination were performed to measure the uterine artery pulsatility index, resistance index, ductus venosus pulsatility index, and blood sampling levels of biomarkers such as b-HCG; PAPP-A; s-FLT-1 and PlGF. Results: There was a significant negative relationship between PAPP-A concentration and the risk of fetal growth restriction, and a significant negative relationship between PlGF concentration and the risk of preeclampsia and fetal growth restriction in women in their first trimester of pregnancy. There was also a significant positive relationship between sFLT-1/PLGF ratio and the risk of developing preeclampsia. No significant relationships were found between the concentrations of biomarkers beta-HCG, PAPP-A, sFLT-1, PlGF, and any of the parameters PIUARt, PIUALt, Mean uterine arteries, and DVPI. Summary: In conclusion, this study did not find conclusive evidence to support the hypothesis that beta-HCG, PAPP-A, s-FLT-1, and PlGF concentrations in women in the first trimester of pregnancy have a significant effect on the Pulsatility Index of the ductus venosus and the Right and left Uterine Arteries. Further research is needed to investigate these potential associations.

The author demonstrates a stable Lagrangian solid modeling method, tracking the interactions of solid mass particles rather than using a meshed grid. This numerical method avoids the problem of tensile instability often seen with smooth particle applied mechanics by having the solid particles apply stresses expected with Hooke's law, as opposed to using a smoothing function for neighboring solid particles. This method has been tested successfully with a bar in tension, compression, and shear, as well as a disk compressed into a flat plate, and the numerical model consistently matched the analytical Hooke's law as well as Hertz contact theory for all examples. The solid modeling numerical method was then built into a 2-D model of a pressure vessel, which was tested with liquid water particles under pressure and simulated with smoothed particle hydrodynamics. This simulation was stable, and demonstrated the feasibility of Lagrangian specification modeling for fluid–solid interactions.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

Abstract: Severe land degradation is the principal environmental problem in Ethiopian highlands in the form of soil erosion, and soil fertility loss, which is caused by human intervention for food, shelter, and energy demands. Soil erosion contributes to the loss of precious soil and water resources which are the basis of agricultural production and provide numerous other eco-system services. The Ethiopian highlands are one of the most degraded regions in the world. To combat such problems, the government of Ethiopia has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. Mount Yewel is one of the highlands in Northeastern Ethiopia where intensive soil and water conserva-tion has been implemented. Despite the massive investment in soil and water conservation measures, most of the rivers in the highlands of Ethiopia carry huge amounts of sediment with high flood risks in the wet season and streams are dried up in the dry period. Nonetheless, the impact of soil and water conservation measures on flood reduction and dry season flow en-hancement has not yet been quantified and evaluated. This research was then conducted on paired micro-catchments of Mount Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were col-lected from 22/11/2020 to 8/11/2022 on paired micro-catchments of Mount Yewel at their outlets and centers respectively. Base flow separation was done from the stream hydrograph using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software were employed for data analysis. Flow duration curves (FDC) for both watersheds were developed to compare the stream flow patterns between treated and untreated micro-catchments of Mount Yewel. The FDC indi-cated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and unsustained in untreated micro-catchment. From statistical analysis, there is a significant (P

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&amp;M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

In Indonesia, types of meat are still identified manually due to increasing prices for beef and buf-falo ahead of Idul Fitri. Traders mix beef with pork to thwart the beef scam. Haar wavelet and GLCM, GLCM with angles of 0°, 45°, 90°, and 135°, as well as matrices using contrast, correlation, energy, homogeneity, and entropy, are used in feature extraction. The following are the results of meat image classification testing using k-NN, Haar wavelet, and GLCM: The k-NN algorithm shows superiority in identifying fresh (99%), frozen (99%), and rotten (96%) meat texture images with the most fantastic accuracy results in every situation. Meanwhile, GLCM routinely provides good results, especially regarding the texture image of fresh meat (183.21) and rotten meat (115.79). However, despite delivering less throughput than k-NN and GLCM, Haar wavelets are still helpful, especially when dealing with fresh meat texture images (89,96).

The commercial oxygen-free copper sheets were cold-rolled with reduction rates ranging from 20% to 87% reduction rate and annealed at 400, 500 and 600 °C. The microstructure and texture evolution during cold-rolling and annealing processes were studied using optical microscopy (OM), the scanning electron microscopy (SEM) and the electron back-scattered diffraction (EBSD). The results show that the deformation textures of {123} (S) , {112} (Copper) and {110} (Brass) were continuously enhanced with the increase of cold-rolling reduction. The orientations along the α-oriented fiber converged towards Brass and the orientation density of β fiber obviously increased when the rolling reduction exceeded 60%. The recrystallization texture was significantly affected by the cold-rolling reduction. After 60% cold-rolling reduction, Copper and S textures components gradually decreased and {011} recrystallization texture component formed with the increase of annealing temperature. After 87% cold-rolling reduction, a strong Cube texture formed and other textures were inhibited with the increase of annealing temperature. The strong Brass and S deformation texture was conducive to the formation of a strong Cube annealing texture. The density of annealing twin boundary decreased with the increase of annealing temperature, and more annealing twin boundaries formed in the oxygen-free copper sheets with the increase of cold rolling reduction.

A U.S. government health agency conducted epidemiological studies to evaluate whether exposures to drinking water contaminated with volatile organic compounds at U.S. Marine Corps Base Camp Lejeune, North Carolina, were associated with increased health risks to children and adults. These health studies required knowledge of contaminant concentrations in drinking water—at monthly intervals—delivered to family housing, barracks, and other facilities within the study area. Because concentration data were limited or unavailable during much of the period of contamination (1950s–1985), the historical reconstruction process was used to quantify estimates of monthly mean contaminant-specific concentrations. This paper integrates many efforts, reports, and papers into a synthesis of the overall approach to, and results from, a drinking-water historical reconstruction study. Results show that at the Tarawa Terrace water treatment plant (WTP) reconstructed (simulated) tetrachloroethylene (PCE) concentrations reached a maximum monthly average value of 183 micrograms per liter (ug/L) compared to a one-time maximum measured value of 215 ug/L and exceeded the U.S. Environmental Protection Agency’s current maximum contaminant level (MCL) of 5 ug/L during the period November 1957–February 1987. At the Hadnot Point WTP, reconstructed trichloroethylene (TCE) concentrations reached a maximum monthly average value of 783 ug/L compared to a one-time maximum measured value of 1,400 ug/L during the period August 1953–December 1984. The Hadnot Point WTP also provided contaminated drinking water to the Holcomb Boulevard housing area continuously prior to June 1972, when the Holcomb Boulevard WTP came on line (maximum reconstructed TCE concentration of 32 ug/L) and intermittently during the period June 1972–February 1985 (maximum reconstructed TCE concentration of 66 ug/L). Applying the historical reconstruction process to quantify contaminant-specific monthly drinking-water concentrations is advantageous for epidemiological studies when compared to using the classical exposed versus unexposed approach.

Unmanned vehicles (UVs) have become increasingly important in various scenarios of civil and military operations. The present work aims at the conceptual design of a modular Amphibious Unmanned Ground Vehicle (A-UGV), that can be easily adapted for different types of land and/or water missions, with low monetary cost (&lt;5k€, without sensors). Basing the design on the needs highlighted in the 2021 review of the Strategic Directive of the Portuguese Navy, the necessary specifications and requirements are established for two mission scenarios. Then a market research analysis focused on vehicles currently available, and their technological advances, is conducted to identify existing UVs solutions and respective characteristics/capabilities of interest to the current work. To study and define the geometry of the hull and the configuration of the A-UGV itself, preliminary computational structural and fluid analyses are carried out to ensure it complies with the specifications initially established. As a result, one obtains a fully electric vehicle, with approximate dimensions of 1050×670×450mm (length-width-height), enabled with 6×6 traction capable of reaching 20km/h in land, possesses amphibious capabilities of independent propulsion in water up to 8kts, and with an estimated autonomy of over 60 minutes.

This study addresses the critical issue of dowel-bearing strength in Bambusa blumeana, a key sus-tainable construction material crucial for climate change mitigation. Given the lack of bamboo connection standards, the research focuses on determining the dowel-bearing strength of Bambusa blumeana, emphasizing factors such as dowel diameter, node placements, and the physical prop-erties of bamboo. A predictive equation is derived, enhancing the practicality of bamboo in struc-tural design. The results underscore a notable correlation between dowel diameter and character-istic strength, with implications for engineering practices. Node placements significantly affect dowel-bearing capacity, while bamboo's physical attributes, including thickness, culm diameter, and moisture content, exhibit modest correlations with strength. The derived equation aims to assist in structural design, mitigating splitting and bearing failures in bamboo structures. This research establishes a foundation for optimizing the use of Bambusa blumeana in sustainable construction, advancing the understanding of its dowel-bearing strength for improved sustainability and resili-ence in the construction industry. Future research suggestions include exploring bamboo-mortar composites, additional node placements, and employing more comprehensive empirical equations and curve-fitting techniques. The study advocates for further investigations with more diverse and larger bamboo samples to bolster robustness. Additionally, delving into bamboo ductility may offer valuable insights.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

In view of the inability to directly and accurately obtain the athlete's aerodynamic force during take-off phase through wind tunnel test, the athlete's aerodynamic force and surrounding flow field form under different take-off postures are obtained through numerical simulation research, and the effects of different take-off modes on the aerodynamic characteristics during take-off in ski jumping are discussed. The multi-body system composed of the athlete and skis was selected as the research objects. By using partially averaged Navier-Stokes (PANS) turbulence model and 3D numerical simulation of computational fluid dynamics (CFD), the aerodynamic characteristics of the athlete under different take-off postures were predicted. Take-off modes include knee-push-hip (KPH) mode and hip-drive-knee (HDK) mode, and the hip joint angle of HDK mode is significantly greater than KPH mode. First, the aerodynamic force ratio of the athlete’s torso and legs is obviously large. Although the aerodynamic force of arms themselves is not obvious, they have a great impact on the overall aerodynamic characteristics of the athlete, so the posture of arms cannot be ignored. Then, the total drag and moment of HDK mode are significantly higher than that of KPH mode, and the lift-to-drag ratio of HDK mode is significantly lower than that of KPH mode. At first the total lift of HDK mode is higher than that of KPH mode, but in the last attitude the total lift of HDK mode does not rise but fall, and finally the total lift of HDK mode is lower than KPH mode. The aerodynamic characteristics change dramatically during take-off phase, and the aerodynamic characteristics of the two take-off modes are quite different, and these changes and differences are difficult to be observed in real training and competition site. KPH mode has obvious aerodynamic advantage over HDK mode. During the take-off process, the athlete should increasethe force generated by the knee joint extension and appropriately reduce the speed of hip joint extension, and control the using force order of the lower limb joints, and push hip joint extension by knee joint extension, in order to avoid issues such as the hip joint angle is too large, the hip joint extension angle is too fast, the center of gravity is to back and other problems. Studying the aerodynamic characteristics during the take-off phase provides valuable insights for athletes to achieve favorable flight postures after take-off, offering scientific guidance to improve training strategies and enhance competitive performance.

Most human genetic disease arises from point mutations. These genetic diseases can theoretically be corrected by gene therapy but clinic practice is still far from mature. Nearly half of the pathogenic single-nucleotide polymorphisms (SNPs) are caused by G:C>A:T or T:A>C:G base changes. The best current methods to repair these changes are by base editing without footprint using recently developed CRISPR-Cas9 technology by David Liu’s lab. These base editing methods have been confirmed with precision and efficiency in cultured mammalian cells, but it is barely confirmed and the efficiency is still very low. Animal models are important in dissecting pathogenic mechanism for human genetic diseases and efficacy testing of base correction in vivo. Cytidine base editor BE4 is a newly developed version of cytidine base editing system that converts cytidine (C) to uridine (U) in cultured mammalian cells but has not been proven in vivo. In this study, we have tested this system in cells to inactivate GFP gene and in mice by introducing single-base substitution that leads to a stop codon in tyrosinase gene. High percentage albino coat-colored mice were obtained from black coat-colored donor zygotes after pronuclei microinjection. Sequencing results showed that expected base changes were obtained with high precision and efficiency (56.25%). There are no off-targeting events identified in predicted off-target sites. Results confirm BE4 system can work in vivo with high precision and efficacy, and has great potentials in clinic to repair human genetic mutations.

This paper focuses on the data-driven evaluation ski resorts, employing the attractiveness index. Unlike similar studies, this research concentrates on smaller resorts essential for local economies. Input data acquired through meta-analysis offers insights into skier preferences, combining information from various sources, including volunteered geographic information (VGI). Employing a geographic information system (GIS), the study addresses pertinent questions regarding over-tourism, regional resort ratings, and spatial patterns, providing a foundation for sustainable development in alpine regions. As the case study, the evaluation of 40 regional ski resorts in Austria is introduced.

Bi1-xSbx crystal is one of the best n-type thermoelectric materials below 200 K, but its weak mechanical strength hinders practical applications for deep refrigeration. Herein, we adopted the mechanical enhancement method of hot extrusion to investigate the comprehensive mechanical and thermoelectric properties of Bi0.905Sb0.095. It revealed that reducing the grain size of the matrix and increasing the extrusion ratio can improve the gain size uniformity and mechanical properties. While the thermoelectric performance depends on the texture, grain size, and local composition. The extruded sample prepared by ingot with the high extrusion ratio of 9:1 generated a high texture degree of (001) plane and small grain sizes between ~4-40 mm, which resulted in the high bending strength of Bi1-xSbx ~130 Mpa and a high-power factor of ~ 68 μW·cm-1·K-2@173 K, as well as the relative high figure of merit of 0.25@173K. This work highlights the importance of the uniform distribution of the grain size and the compositions for Bi1-xSbx, as well as the required universal key parameter for the hot-extrusion method.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

In practical applications, the detection of objects with various sizes is a common requirement for most detectors. The feature pyramid network (FPN) is widely adopted as a framework to address this challenge. The field is witnessing an increasing number of transformer-based target detectors due to the widespread adoption of transformer technology. This paper initially examines the design flaws in FPN and transformer-based target detectors, followed by the introduction of a new transformer-based approach called Texturized Instance Guidance (TIG-DETR) to address these issues. Specifically, TIG-DETR comprises a backbone network, a new pyramidal structure known as Texture-Enhanced FPN (TE-FPN), and an enhanced DETR detector.The TE-FPN is composed of three components: a bottom-up pathway for enhancing texture information in the feature map, a lightweight attention module to address confounding effects resulting from cross-scale fusion, and a standard attention module to enhance the final output features.The improved DETR detector utilizes Shifted Window based Self-Attention to replace the multi-headed self-attention module in DETR, thereby accelerating model convergence. Moreover, it incorporates an Instance Based Advanced Guidance Module to enhance instance perception in the image by employing a pre-local self-attentive mechanism for recognizing larger instances. By employing TE-FPN instead of FPN in Faster RCNN with Resnet-50 as the backbone network, we achieve a 1.9% improvement in average accuracy. TIG-DETR achieves an average accuracy of 44.1 with Resnet-50 as the backbone network.

Soil texture is key information in agriculture for improving soil knowledge and crop performance, so the accurate mapping of this crucial feature is imperative for rationally planning cultivations and for targeting interventions. We studied the relationship between radioelements and soil texture in the Mezzano Lowland (Italy), a 189 km² agricultural plain investigated through a dedicated airborne gamma-ray spectroscopy survey. The K and Th abundances were used to retrieve the clay and sand content by means of a multi-approach method. Linear (simple and multiple) and non-linear (machine learning algorithms with deep neural networks) predictive models were trained and tested adopting a 1:50,000 scale soil texture map. The comparison of these approaches highlighted that the non-linear model introduces significant improvements in the prediction of soil texture fractions. The predicted maps of the clay and of the sand content were compared with the regional soil maps. Although the macro-structures were equally present, the airborne gamma-ray data permits us shedding light on finer features. Map areas with higher clay content were coincident with paleo-channels crossing the Mezzano Lowland in Etruscan and Roman periods, confirmed by the hydrographic setting of historical maps and by the geo-morphological features of the study area.

This paper compares a series of traditional and deep learning methodologies for the segmentation of textures. Six well-known texture composites first published by Randen and Hus{\o}y were used to compare traditional segmentation techniques (co-occurrence, filtering, local binary patterns, watershed, multiresolution sub-band filtering) against a deep-learning approach based on the U-Net architecture. For the latter, the effects of depth of the network, number of epochs and different optimisation algorithms were investigated. Overall, the best results were provided by the deep-learning approach. However, the best results were distributed within the parameters, and many configurations provided results well below the traditional techniques.

Objective: The stability of the flight phase in ski jumping is crucial for athletes' performance and safety. This study aims to investigate the influence of unfavorable conditions on aerodynamic characteristics and flight stability through computational fluid dynamics (CFD) numerical simulations. Methods: The ski jumper and the skis are considered as a multi-body system. A detailed three-dimensional (3D) model of this multi-body system under a commonly observed posture during flight is established. The partially averaged Navier-Stokes (PANS) turbulence model is employed, and CFD simulations are conducted to predict the aerodynamic characteristics of the multi-body system under lateral environmental wind and asymmetric postures during flight phase. The conditions of asymmetric postures include yaw rotation and roll rotation. Results: (1) Lateral environmental wind generated yaw force, yaw moment, and roll moment, which influenced the lift, drag, and pitch moment of the athlete. These forces and moments were relatively small at lower wind speeds (less than 3 m/s) and became more significant at higher wind speeds (greater than 4.5 m/s). (2) Under the influence of yaw rotation or roll rotation, the multi-body system exhibited noticeable yaw force, yaw moment, and roll moment, all showing a monotonic increasing trend. Moreover, they had a significant impact on the lift, drag, and pitch moment of the multi-body system. Conclusion: (1) The influence of unfavorable conditions is complex, resulting in significant yaw force, yaw moment, and roll moment on the multi-body system. The adverse effects of roll rotation were generally greater than those of yaw rotation. (2) The multi-body system exhibited self-stabilizing tendencies in yaw and roll. This phenomenon can provide a solution to maintain flight stability by employing appropriate yaw or (and) roll rotation angles, effectively compensating for or even eliminating the adverse effects of lateral environmental wind. (3) Understanding the mechanisms of how unfavorable conditions affect the aerodynamic characteristics and stability during flight in ski jumping can provide valuable assistance for real-time prediction and decision-making during competitions, as well as scientific guidance for training athletes stable flight control and techniques and improving their sport performance.

Bamboo is considered a sustainable construction material due to its ability to grow quickly and its mechanical properties that are comparable to timber. Contributing to the current effort to establish the structural bamboo standards in the National Structural Code of the Philippines (NSCP), this study establishes the characteristic compressive strength of four bamboo species: Bambusa vulgaris (36 samples), Dendrocalamus asper (36 samples), Bambusa blumeana (94 samples), and Guadua angustifolia Kunth (30 samples). The samples were subjected to compressive loading following ISO 22157-1 (2017). The characteristic compressive strength values obtained, according to ISO 12122-1 (2014), were 40.35 MPa for B. vulgaris, 40.21 MPa for D. asper, 46.63 MPa for B. blumeana, and 36.99 MPa for G. angustifolia Kunth. Simple linear analysis, One-way ANOVA, and Welch’s t-Test were used to analyze the correlation models and establish a comparative analysis of the effect of nodes, and geometric and physical properties on the compressive strength of bamboos. Comparing the characteristic compressive strength obtained from this study to the strength of unseasoned structural timber of Philippine woods, all bamboo species showed higher strength values, and thus have great potential as an alternative construction material to timber.

A random variable X that is base b Benford will not in general be base c Benford when c is not equal to b. This paper builds on two of my earlier papers and is an attempt to cast some light on the issue of base dependence. Following some introductory material, the “Benford spectrum” of a positive random variable is introduced and known analytic results about Benford spectra are summarized. Some standard machinery for a “Benford analysis” is introduced and combined with my method of “seed functions” to yield tools to analyze the base c Benford properties of a base b Benford random variable. Examples are generated by applying these general methods to several families of Benford random variables. Berger and Hill's concept of “base-invariant significant digits” is discussed. Some potential extensions are sketched.

Texture has long been considered an important attribute for food acceptance. However, which specific textural characteristics contribute to overall acceptance of a food is not well understood. It has been suggested that texture contrasts and combinations are a universal feature in giving foods a desirable texture, yet this notion is largely based upon anecdotal data. This study uses multiple survey research methods to assess the importance of texture contrast and combinations across cultures (Poland, U.S.A., and Singapore). Participants (n = 288) completed a survey that included overt measures of food texture contrast importance as well as free response questions regarding texture. The overall importance of texture for food liking was not different across the populations. However, the participants from Singapore and Poland gave more importance to a desirable food having multiple textures than the U.S.A. cohort. When looking at free responses, participants were twice as likely to mention combinations (multiple textures) with a texture contrast when describing foods they liked, in comparison to foods they disliked. This was observed across all 3 cultures. However, the type and quantity of texture terms used within combinations were different among cultures. For instance, Asians enjoyed more texturally diverse food combinations than the other two cultures. These findings highlight the importance of texture contrasts and combinations in three distinct cultures.

As most of the videos are destined for human perception, many techniques have been designed to improve video coding based on how the human visual system perceives video quality. In this paper, we propose the use of two perceptual coding techniques, namely contrast masking and texture masking, jointly operating under the High Efficiency Video Coding (HEVC) standard. These techniques aim to improve the subjective quality of the reconstructed video at the same bit rate. For contrast masking, we propose the use of a specific weighting matrix for each block size (from 4×4 up to 32×32). We achieve average Bjøntegaard Delta-Rate (BD-rate) gains of between 2.5% and 4.48%, depending on the perceptual metric and coding mode used. The texture masking scheme is based on the classification of each coding unit, using its mean directional variance features as input to a support vector machine model. According to this classification, the block’s energy, the type of coding unit, and its size, an over-quantization is computed to provide a QP offset (DQP) for this coding unit. By applying both techniques in the HEVC Reference Software, an overall average of 5.79% BD-rate gain is achieved.

In many image processing and computer vision applications, the main aim is to describe image contents. So, different visual properties such as color, texture and shape are extracted to make aim. In this respect, texture information play important role in image description and visual pattern classification. Texture is referred to a specific local distribution of intensities that is repeated throughout the image. Since now different operations or descriptors have been proposed to analysis texture characteristics. In the multi object images specific texture operators usually doesn’t provide accurate results. So, in many cases, combination of texture operators are used to achieve more discriminant features. In this paper, some combination methods are survived to analysis effect of combinational texture features in image content description. Also, in the result part, different related methods are compared in terms of accuracy and computational complexity.

While texturing of workpiece surfaces to promote lubrication in metal forming has been applied for several decades tool surface texturing is rather new. In the present paper tool texturing is studied as a method to prevent galling. Adopting a strip reduction test longitudinal pocket geometries oriented perpendicular to the sliding direction, with shallow pocket depth, small pocket angle to the workpiece surface and varying distance between pockets are investigated. The experiments reveal that the distance between pockets should be larger than the pocket width thereby creating a topography similar to flat table mountains to avoid mechanical interlocking in the valleys; otherwise an increase in drawing load and pick-up on the tools is observed. The textured tool surface lowers friction and improves lubrication performance provided that the distance between pockets is 2-4 times larger than the pocket width. Larger drawing speed facilitates escape of the entrapped lubricant in the pockets. Testing with low to medium viscosity oils leads to a low sheet roughness on the plateaus but also local workpiece material pick-up on the tool plateaus. Large lubricant viscosity results in higher sheet plateau roughness but also prevents pick-up and galling.

Unmanned aerial vehicles serving as air base stations (UAV-BSs) are used in telecommunications, when the network is overloaded or unavailable, providing access to users on the ground. Due to its dynamics of providing access to networks in different altitudes, the electromagnetic signal of UAVs suffers losses along the path, thus facing several problems related to transmission, such as: attenuation, fading and distortion. In this work is proposed a 3D positioning strategy for UAVs, taking into account height, coverage radius and flight energy efficiency. Results show that the proposed algorithm is able to position the UAVs in suboptimal locations, providing network access for mobile users, maximizing the number of connected devices in the UAV-BS and saving energy, thus obtaining better performance than the approaches conventional.

In directional forming processes such as rolling and extrusion, the microstructure is strongly elongated in the forming direction. This results in a preferred alignment of the crystal orientations of the initially randomly oriented grains. These preferred orientations – the texture – and elongations of the grains are the cause of the material anisotropy. This anisotropy leads to phenomena such as earing, which occur during further forming processes, e.g., during deep drawing of sheet metal. Considering anisotropic properties in numerical simulations allows to investigate the effects of texture-dependent defects in forming processes and the development of possible solutions. Purely phenomenological models for modelling anisotropy work by fitting material parameters or applying measured R-values in experiments which are applied to all elements of the part and remain constant over the duration of the simulation. In contrast, methods such as the Visco-Plastic Self-Consistent (VPSC) model, which has been used in this work, provide a deeper insight into the development of the material microstructure. By experimentally measuring the initial texture and using it as an initial condition for the simulations, it is possible to predict the evolution of the microstructure and the resulting effect on the mechanical properties during forming operations. The results of the simulations with VPSC show good qualitative agreement with tests typically used for rolled stock.

This paper discusses the computer-aided (CAD) classification between Hepatocellular Carcinoma (HCC), i.e., the most common type of liver cancer, and Liver Abscess, based on ultrasound image texture features and Support Vector Machine (SVM) classifier. Among 79 cases of liver diseases, with 44 cases of HCC and 35 cases of liver abscess, this research extracts 96 features of Gray-Level Co-occurrence Matrix (GLCM) and Gray-Level Run-Length Matrix (GLRLM) from the region of interests (ROIs) in ultrasound images. Three feature selection models, i) Sequential Forward Selection, ii) Sequential Backward Selection, and iii) F-score, are adopted to determine the identification of these liver diseases. Finally, the developed system can classify HCC and liver abscess by SVM with the accuracy of 88.875%. The proposed methods can provide diagnostic assistance while distinguishing two kinds of liver diseases by using a CAD system.

Automatic garments design class identification for recommending the fashion trends is important nowadays because of the rapid growth of online shopping. By learning the properties of images efficiently, a machine can give better accuracy of classification. Several methods, based on Hand-Engineered feature coding exist for identifying garments design classes. But, most of the time, those methods do not help to achieve better results. Recently, Deep Convolutional Neural Networks (CNNs) have shown better performances for different object recognition. Deep CNN uses multiple levels of representation and abstraction that helps a machine to understand the types of data (images, sound, and text) more accurately. In this paper, we have applied deep CNN for identifying garments design classes. To evaluate the performances, we used two well-known CNN models AlexNet and VGGNet on two different datasets. We also propose a new CNN model based on AlexNet and found better results than existing state-of-the-art by a significant margin.

A series of novel indole Schiff base derivatives (2a–2t) containing a 1,3,4-thiadiazole scaffold modified with a thioether group were synthesized, and their structures were confirmed using FT-IR, ¹H NMR, ¹³C NMR, andHR-MS. In addition, the antifungal activity of synthesized indole derivatives was investigated against Fusarium graminearum (F. graminearum), Fusarium oxysporum (F. oxysporum), Fusarium moniliforme (F. moniliforme), Curvularia lunata (C. lunata), and Phytophthora parasitica var. nicotiana (P. p. var. nicotianae) using the mycelium growth rate method. Among the synthesized indole derivatives, compound 2j showed the highest inhibition rates of 100%, 95.7%, 89%, and 76.5% at a concentration of 500 μg/mL against F. graminearum, F. oxysporum, F. moniliforme, and P. p. var. nicotianae, respectively. Similarly, compounds 2j and 2q exhibited higher inhibition rates of 81.9% and 83.7% at a concentration of 500 μg/mL against C. lunata. In addition, compound 2j has been recognized as a potential compound for further investigation in the field of fungicides.

There is a fast-growing interest in the use of selective laser melting (SLM) for metal/alloy additive manufacturing. Our current knowledge of SLM printed 316 stainless steel (SS316) is limited and sometimes appears sporadic, presumably due to the complex interdependent effects of a large number of process variables of the SLM processing. This is reflected from the discrepant findings in the crystallographic textures and microstructures in this investigation with those reported in the literatures, which also vary itself. The as-printed material is macroscopically asymmetric in both the structures and crystallographic textures. The <101> and <111> crystallographic directions align parallel with the SLM scanning direction (SD) and build direction (BD), respectively. Like-wise, some characteristic low angle boundary features are reported crystallographic, while this investigation unequivocally proves them non-crystallographic since they always maintain an identical alignment with the SLM laser scanning direction irrespective of the matrix material’s crystal orientation. There is also 500±200 nm columnar or cellular features, depending on the cross-section, generally found all over the sample. These columnar or cellular features are formed with walls made of dense packing of dislocations entangled with Mn, Si and O enriched amorphous inclusions. They remain stable after the ASM solution treatments at 1050 °C temperatures, and therefore, are capable of hindering boundary migration events of recrystallization and grain growth. Thus, the nanoscale structures can be retained at high temperatures. Large 2-4 µm inclusions form during the solution treatment, within which the chemical and phase distribution are heterogeneous.

Tunicate orthologs in the human genome comprise just 84 genes of the 19,872 protein-coding genes, yet they stand at the base of the Olfactores clade - which radiated to generate thousands of tunicate and vertebrate species. What were the powerful drivers among the 84 that enabled this process? Many of these orthologs are present in gene families. We discuss the biological role of each family and the orthologs’ quantitative contribution to the family. Most important was the evolution of a second type of cadherin. This, a Type II cadherin, had the property of detaching the cell containing that cadherin from cells that expressed the Type I class. The set of such Type II cadherins could now detach and move away from their Type I neighbours, a process which would eventually evolve into the formation of the neural crest, “ the fourth germ layer”, providing a wide range of possibilities for further evolutionary invention. A second important contribution were key additions to the broad development of the muscle and nerve protein and visual perception tool-kits. These developments in mobility and vision provided the basis for the development of the efficient predatory capabilities of the Vertebrata.

ORB (Oriented FAST and Rotated Brief) features are the most commonly used features in visual SLAM and visual odometry that have high computational speed, and rotation scale invariance. However, due to the homogenization of ORB features, the corner properties of specific features are poor in some artificial environments, and it can lead to poor matching performance when the environmental texture is not rich. The underlying reason is that the pixel grayscale changes in the less-richly textured regions on the image are not obvious, leading to a certain degree of mis-matching in the matching process. At the same time, when the camera motion speed is low, there is much overlap between adjacent frames. This results in minimal or almost no changes in the projection of feature points, and the system is highly sensitive to errors, In this case, even small errors can cause significant fluctuations in the calculation results. In response to the above issues, an improved feature point method for stereo vision mileage calculation is proposed to solve the problem of system stability deterioration when cameras move at low speeds in artificial envi-ronments. Firstly, weight calculation based on different texture regions is used to solve the problem of low corner properties of feature points caused by environmental texture differences. Then, keyframes are used for motion model estimation to improve the system's stability under low-speed motion. The experimental results of the dataset showed that the key frame rate was optimal between 10% and 12%, and the positioning accuracy was higher than these open-source systems compared with three common open-source VO systems.

Obstructive sleep apnea (OSA) is multi-faceted world-wide distributed disorder exerting deep effects on the sleeping brain. In the latest years strong efforts have been dedicated to find novel measures assessing the real impact and severity of the pathology, traditionally trivialized by the simplistic apnea/hypopnea index. Due to the unavoidable connection between OSA and sleep we reviewed the key aspects linking the breathing disorder with sleep pathophysiology, focuings on the role of cyclic alternating pattern (CAP). Sleep structure, reflecting the degree of apnea-induced sleep instability, may provide topical informations to stratify OSA severity and foresee some of its dangerous consequences such as excessive daytime sleepiness and cognitive deterioration.

This paper presents a robust method based on graph topology to find the topologically correct and consistent subset of inter-robot relative pose measurements for multi-robot map fusion. However, the absence of good prior gives a severe challenge to distinguish the inliers and outliers, and wrong loop closures can seriously corrupt the fused global map. Existing works mainly rely on the consistency of spatial dimension to select inter-robot measurements, which does not always hold. In this paper, we propose a fast inter-robot loop closure selection method that integrates the consistency and topology relationship of measurements, which both conform to the continuity characteristics of similar scenes and spatiotemporal consistency. The traditional high-dimensional consistency matrix is decomposed into the sub-matrix blocks corresponding to the overlapping trajectory area. Building on this logic, a clustering method involving topology correctness of inter-robot loop closures is introduced to split the entire measurement set into multiple clusters. We define the weight function to find the maximum cardinality subset with topologically correct and consistent, then convert the weight function to a maximum clique problem in the graph and solve it. We evaluate the performance of our method in a simulation and in a real-world experiment. Compared to state-of-the-art methods, the results show that our method can achieve competitive performance in accuracy while reducing computation time by 75%.

This paper presented a feature vector using a different statistical texture analysis of brain tumor from MRI image. The statistical feature texture is computed using GLCM (Gray Level Co-occurrence Matrices) of Brain Nodule structure. For this paper, the brain nodule segmented using strips method to implemented marker watershed image segmentation based on PSO (Particle Swarm Optimization) and Fuzzy C-means clustering (FCM). Furthermore, the four angles 0^o, 45^o, 90^o and 135^o are calculated the segmented brain image in GLCM. The four angular directions are calculated using texture features are correlation, energy, contrast and homogeneity. The texture analysis is performed a different types of images using past years. So the algorithm proposed statistical texture features are calculated for iterative image segmentation. These results show that MRI image can be implemented in a system of brain cancer detection.

The present work shows a novel physical-mathematical model to estimate the average corrosion resistance index from the crystallographic texture in API 5L steels. The crystallographic texture of the studied steels was measured by means of the X-ray diffraction technique. The model, based on the symmetric spherical surface harmonics for a BCC structure, is capable of describing the anisotropy surface of anodic dissolution resistance of the crystal and establishing a straightforward relationship between crystallographic texture, surface roughness, and metal corrosion behavior. The predictions of the average corrosion resistance index made from the crystallographic texture were in good agreement with those obtained from potentiodynamic polarization curves for the investigated steels. This agreement validates the capacity of this model and opens the possibility of applying it as a novel criterion for the material selection and design stages in order to combat metal corrosion problems.

A new low-pass filter (LPF) circuit with independent adjustment of various, incl. digitally controlled, pole frequency resistors, pole quality factor and transmission coefficient. The proposed low-pass filter is based on the use of the properties of a multi-differential operational amplifier that performs the functions of a signal adder. The peculiarity of the filter is that it has three inputs, with respect to which different transmission coefficients are implemented, incl. inverting (-1) and non-inverting (+1). To check these properties of a low-pass filter in the Micro-Cap environment, computer simulation of a specific circuit was performed on a multi-differential operational amplifier AD 8130. Mathematical expressions are given for the main parameters of the proposed low-pass filter, which allow parametric synthesis of elements of a specific circuit under given restrictions on the used element base.

Abstract: Two novel low-dimensional molecular magnetic materials were prepared by a self-assembling of 3d- and 5d-metal complexes. These are the first neutral heterobimetallic cyanobridged compounds involving one anisotropic Mn(III) Schiff base complex and one octacyanotungstate(V) per molecular unit. A slow diffusion of the constituents’ solutions leads to a formation of the 0D crystalline complex 1 due to coordination of a water molecule to the Mn center prevents a polymer formation. A rapid mixing of reagents results in a precipitation of the microcrystalline powder of the complex 2, which on a totality of experimental data possess 1D polymeric structure. The magnetic studies have shown that antiferromagnetic exchange interactions are dominating in 1 J/k_B= -13.1(7) K, D=-3.0(1.3) K, zJ'= -0.16(20) K and g_av=2.00(1); while the presence of the significant intramolecular Mn(III)–W(V) ferromagnetic couplings through cyanide bridges is characteristic for 2 (J/k_B = 46.1(5) K g_Mn = 2.11(3), fixed g_W = 2.0). Due to the weak interchain interactions, zJ'/k_B = –0.8(2) K, compound 2 is a metamagnet with the Néel temperature of 9.5 K undergoing a spin-flip transition at 2 kOe. The slow magnetization dynamics of 2 was investigated at DС field of 0 and 2 kOe, giving the values of τ₀ 32(15) and 36(15) ps respectively, well within the range typical for SCMs. The respective ∆_τ/k_B values were 48.4(1.2) and 44.9(1.0) K.

Many (if not a very large number) of metals and alloys evince substantial softening with torsion deformation to strains not usually achievable in tension. Of course, softening has long been observed by discontinuous dynamic recrystallization (DDRX) but this paper will discuss cases where softening is associated by texture development with large-strain deformation that is not reliant on changes in the dislocation hardening. This paper reviews the work of the current authors on FCC metals and alloys in this area and extends to a new discussion of BCC and HCP cases.

The information of seismic damage of buildings in SAR images of different time phase, especially in SAR images after earthquake, is easily disturbed by other factors, which affects the accuracy of information discrimination. In order to identify and evaluate the distribution information of the seismic damage accurately and make full use of the abundant texture features in the SAR image. The conventional method of change detection based on texture features usually takes the pixel as the calculating unit. In this paper, a method of texture feature change detection of SAR images based on watershed segmentation algorithm is proposed. Based on the optimization of texture feature parameters, the feature parameters are segmented by the watershed segmentation algorithm, and the feature object image is obtained. This method introduces the idea of object oriented, and carries out the calculation of the difference map at the object level, Finally, the classification threshold value of different types of seismic damage types is selected, and the recognition of building damage is achieved. Taking the ALOS data before and after the earthquake in Yushu as an example to verify the effectiveness of the method, the overall accuracy of the building extraction is 88.9%, Compared with pixel-based methods, it is proved that the proposed method is effective.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

In the polar region, the gravity vector and Earth's rotation vector tend to be in the same direction, leading to slower convergence speed and longer alignment time of the moving base alignment. When the alignment time is short, the alignment cannot converge, resulting in low azimuth accuracy. To address this issue, we propose a polar moving base alignment method based on backtracking scheme. Notably, this work first derives a polar coarse alignment method with the inertial frame based on the transverse Earth model. On this basis, we design a polar coarse alignment method based on backtracking scheme and optimize the data storage scheme. Then, an inverse navigation algorithm based on the transverse inertial navigation mechanical arrangement scheme was derived, and a polar fine alignment method based on backtracking scheme was designed. Semi-physical simulation experiments showed that the alignment algorithm based on backtracking scheme can converge in a short time with high alignment accuracy.

Multiplex genome editing may induce genotoxicity and chromosomal rearrangements due to double-strand DNA breaks at multiple loci simultaneously induced by programmable nucleases, including CRISPR/Cas9. However, recently developed base-editing systems can directly substitute target sequences without double-strand breaks. Thus, the base-editing system is expected to be a safer method for multiplex genome-editing platforms for livestock. Target-AID is a base editing system composed of PmCDA1, a cytidine deaminase from sea lampreys, fused to Cas9 nickase. It can be used to substitute cytosine for thymine in 3-5 base editing windows, 18 bases upstream of the protospacer-adjacent motif site. In the current study, we demonstrated Target-AID-mediated base editing in porcine cells for the first time. We targeted multiple loci in the porcine genome using the Target-AID system and successfully induced target-specific base substitutions with up to 63.15% efficiency. This system can be used for the further production of various genome-engineered pigs.

We have previously clarified that the strongly electron-withdrawing CF3 group nicely affected the base-mediated proton migration reactions of CF3-containinig propargylic or allylic alcohols to afford the corresponding a,b-unsaturated or saturated ketones, respectively, which was applied this time to the Claisen rearrangement after O-allylation of the allylic alcohols, followed by isomerization to the corresponding allyl vinyl ethers, enabling the desired rearrangement in a tandem fashion, or in a stepwise manner where a palladium catalyst attained an excellent diastereoselectivity.

The article presents the Base Point Split (BPSplit) algorithm for generating a polygon skeleton based on sets of vector data describing lakes and rivers. A key feature of the BPSplit algorithm is that it is dependent on base points representing the source or mouth of a river or a stream. The input values of base points determine the shape of the resulting skeleton. Various skeletons can be generated with the use of different base points. Base points are applied to divide polygon boundaries into segments. Segmentation supports the selection of TIN edges inside polygons. The midpoints of selected TIN edges constitute a basis for generating a skeleton. The algorithm handles polygons with numerous holes, and it accounts for all holes. This article proposes a method for modifying a complex skeleton with numerous holes. In the discussed approach, skeleton edges that do not meet the preset criteria (e.g. that the skeleton is to be located between holes in the center of the polygon), are automatically removed. A simple algorithm for smoothing zigzag lines was proposed.

Vertical-channel organic dual-gate/base transistors would be highly interesting since vertical organic transistors are the fastest organic transistors demonstrated today. However, incorporating a dual gate/base structure into an ultra-short channel vertical architecture represents a substantial challenge. Here, we successfully realize a new device concept of vertical organic permeable dual-base transistors (OPDBTs), where either of both base electrodes can be used to change the on-currents and tune the threshold voltages. The optimized devices yield a high on-current density of 1.54 A cm^-2 and a large current gain of 9.2×10⁵, corresponding to a high transmission value of 99.998%. The detailed operation mechanisms are investigated by calibrated TCAD simulations with the Poole-Frenkel mobility model, Gaussian density of states and tunneling model. Finally, high-performance logic circuits, e.g. inverter, NAND/AND computation functions are demonstrated with one single OPDBT operating at supply voltages of < 2.0 V. We believe that OPDBTs offer a compact and technologically simple hardware platform with excellent application potential for vertical-channel organic transistors in complex logic circuits.

A waterbody detection technique is an essential part of digital elevation model (DEM) generation to delineate land-water boundaries and set flattened elevations. This paper describes the technical methodology for improving the initial tile-based waterbody data that are created during production of the ASTER GDEM, because without improvement such tile-based waterbody data are not suitable for incorporating into the new ASTER GDEM Version 3. Waterbodies are classified into three categories: sea, lake, and river. For sea-waterbodies, the effect of sea ice is removed to better delineate sea shorelines in high latitude areas, because sea ice prevents accurate delineation of sea shorelines. For lake-waterbodies, the major part of the processing is to set the unique elevation value for each lake using a mosaic image that covers the entire lake area. Rivers present a unique challenge, because their elevations gradually step down from upstream to downstream. Initially, visual inspection is required to separate rivers from lakes. A stepwise elevation assignment, with a step of one meter, is carried out by manual or automated methods, depending on the situation. The ASTER GWBD product consists of a global set of 1º latitude-by-1º longitude tiles containing water body attribute and elevation data files in geographic latitude and longitude coordinates and with one arc second posting. Each tile contains 3601-by-3601 data points. All improved waterbody elevation data are incorporated into the ASTER GDEM to reflect the improved results.

Halloysite and kaolinite are dioctahedral TO phyllosilicates that drive the interest of scientists for formulating environmental friendly materials, and consequently in the field of ceramics. The main scope of this study was the understanding of the texture evolution upon the dehydroxylation reaction and the influence of the presence of halloysite. In situ synchrotron (002) and (111) poles figures were recorded on the DiffAbs beamline at SOLEIL Synchrotron, from room temperature to 1000°C, on kaolinite and/or halloysite-rich samples shaped by tape casting. Commercial kaolins and halloysite provided by Imerys company were used. The samples were labeled KRG100, KCS100, H100, KRG50H50 and KRG59H50 in relation with the wt. % of kaolin (KRG, KCS) or halloysite (H) clays. In samples KCS100 and KRG100, a strong texture was observed until in situ annealing at 700°C, with respect to the c-axis of kaolinite. One the contrary, the texture with respect to the c-axis of halloysite for the sample H100 was weak whatever the temperature was. Moreover, this weak texture disappeared before the complete dehydroxylation of halloysite. This is due to the opening of some halloysite tubes. When considering the samples KRG50H50 and KCS50H50, a significant texture was observed with the c-axis preferentially oriented perpendicular to the sample surface . The presence of kaolinite platelets predominated onto the alignment of halloysites tubes. Furthermore, it was noted that the halloysite influenced the (002) diffracted intensity into the temperature range 20 °C and 400 °C. Above 400°C, the behavior obtained for the (002) reflection in samples KRG50H50 and KCS50H50 was similar to the behavior noticed for pure kaolins KRG100 and KCS100 respectively. The dehydroxylation temperature range appeared to be relevant with combined effect of kaolinite and halloysite transformations arising from KRG100 or KCS100 and H100 samples. Therefore, the onset point of dehydroxylation is 550 °C ± 25 °C for KRG100, KCS100 KRG50H50 and KCS50H50. For the pure halloysite H100 sample, the dehydroxylation starts at lower temperature 475°C. It was also noted that during the dehydroxylation of kaolinite, the characteristic portion of ring related to the diffracted intensity of the (111) reflection located at χ = 45 ° tended to disappear above 550 °C and led to the formation of a new transitory phase with a (111) reflection with perpendicular alignment to the c-axis. Indeed, an epitaxial relationship with the (111) kaolinite reflection could be assumed. Further X-ray scattering experiments allowed highlighting the effective offset temperature of the dehydroxylation, which was identified as close to 720 °C. The metakaolinite obtained undergone structural transformation to another transitory phase at 1000°C.

Objective: The aim of this study was to provide a new machine learning method to determine temporal events and inner-cycle parameters (e.g., cycle, poles and skis contact and swing time) in cross-country roller ski skating on the field, using a single deported inertial measurement unit (IMU). Methods: The developed method is based on long short-term memory neural networks to detect poles and skis initial and final contact with the ground during the cyclic movements. Eleven athletes skied four laps of 2.5 km at low and high intensity using skis with two different rolling coefficients. They were equipped with IMUs attached to the upper back, lower back and to the sternum. Data from force insoles and force poles were used as reference system. Results: The IMU placed on the upper back provided the best results, as the LSTM network was able to determine the temporal events with an accuracy ranging from 49 to 55 ms and the corresponding inner-cycles parameters were calculated with a precision of 63 to 68 ms. The method detected 95% of the events for the poles and 87% of the events for the skis. Conclusion: The proposed LSTM method provides a promising tool for assessing temporal events and inner-cycle phases in roller ski skating showing the potential of using a deported IMU to estimate different spatio-temporal parameters of human locomotion.

The aims of this research were to know the physicochemical parameters, texture properties and sensory profile of vegetarian sausages through the flash profile, overall liking and purchase intention. Additionally, protein, fat and carbohydrate contents, pH, water activity, color, instrumental texture and descriptive profile were quantified with the overall liking and purchase intention of four sausages: ovo-vegetarian (SO), classic vegan (SC), fine herb vegan (SH) and vegan quinoa (SQ). Regarding the physicochemical properties, significant differences (p &lt; 0.05) were obtained. Using the flash profile, consumers described SO with attributes of elasticity, tamale smell, strange smell, characteristic flavor, pastiness, softness, pastel color. SC described as soft, pale color, characteristic odor, characteristic flavor, porous and flexible; SH and SQ characterized by the presence of ingredients, stew flavor, spices, pale and soft color. The SO sample presented greater overall liking and purchase intention compared to the other samples, and had a better texture and higher protein content. Through the HMFA analysis, a positive correlation was obtained between the texture and descriptive sensory of the flash profile, and on the other hand, a correlation between the physicochemical characteristics pH, aw, color, overall liking and purchase intention.

Watermelon fruits of different ploidy exhibit significant variations in texture. In order to investigate the primary factors influencing texture differences, this study was conducted to investigate the differences in fruit texture development using homozygous autogamous diploid (2X)lines and their autotriploid (3X) and autotetraploid (4X) lines 'Yixuan'. The research encompassed fruit development, flesh texture profile analysis (TPA), flesh cell wall polysaccharide content, and flesh cell microstructure analysis, specifically in 2X, 3X, and 4X watermelon fruits.The results showed that as watermelon fruits matured, several characteristics exhibited an ascending trend, including fruit weight, TSS (total soluble solids) content, rind hardness, flesh cell size, and cell wall polysaccharide contents such as crude fiber, cellulose, hemicellulose, lignin, and protopectin. Conversely, the flesh texture parameters and soluble pectin content of the flesh cell wall gradually declined. Notably, significant differences in fruit flesh texture and flesh cell structure were observed among fruits of different ploidy at the 32d. Specifically, 2X fruits displayed considerably lower rind hardness, reduced flesh texture (Hardness, Fracturability, Chewiness, Gumminess), and cell density compared to 3X and 4X fruits. Additionally, 2X fruits exhibited larger cell sizes than 3X and 4X fruits. However, no significant differences were observed in the content of flesh cell wall polysaccharide contents across various ploidy levels.These findings suggested that the variation in texture among watermelon fruits of different ploidy can be attributed to the size and arrangement of flesh cells. Importantly, this research provided a foundation for further exploration of the intrinsic regulatory factors and molecular mechanisms contributing to texture variation in polyploid watermelon fruits.

In order to realize rapid and nondestructive monitoring of wheat biomass in field, field experiments based on different densities, nitrogen fertilizer and variety treatments were studied. RGB images of wheat in the main growth stage were obtained by UAV, and wheat color and texture feature indices were obtained by image processing, and wheat biomass was obtained by field sampling in the same period. Then the relationship between different color and texture feature indices and wheat biomass was analyzed to select the color and texture feature index suitable for wheat biomass estimation. The results showed that there was a high correlation between image color index and wheat biomass in different stages, and most of them reached a very significant correlation level. However, the correlation between image texture feature index and wheat biomass was poor, only a few indexes reached significant or extremely significant correlation level. Based on the above results, the color indices with the highest correlation to wheat biomass or the combining indices of color and texture feature in different growth stage were used to construct estimation model of wheat biomass. The models were validated using independently measured biomass data, and the correlation between simulated and measured values reached the significant level, RMSE were smaller. This indicated that the estimated results by the models were reliable and accurate. It also showed that the estimation models of wheat biomass combined with color and texture feature indices of UAV image were better than the single color index models. The results would provide a new method for real-time monitoring of wheat field growth and biomass estimation.

Polyalcohol liquefaction can be done by acid or basic catalysis producing polyols with different properties. This study compared the mechanical properties of foams produced using polyols from liquefied Cytisus scoparius obtained by acid and basic catalysis and using two different foam catalysts. The differences were monitored using FTIR analysis. Acid-catalyzed liquefaction yielded 95.1 %, with the resultant polyol having an OH index of 1081 mg KOH/g while basic catalysis yielded 82.5 %, with a similar OH index of 1070 mg KOH/g. Generally, compressive strength with dibutyltin dilaurate (DBTDL) ranged from 16 - 31 kPa (acid-liquefied polyol) and 12 -21 kPa (base-liquefied polyol), while with stannous octoate (TIN), it ranged from 17 - 42 kPa (acid) and 29 - 68 kPa (base). Increasing water content generally decreased the compressive modulus and strength of foams. Higher water content led to a higher absorption at 1670 cm-1 in the FTIR spectrum due to the formation of urea. Higher isocyanate indices generally improved compressive strength, but high amounts led to unreacted isocyanate that could be seen by a higher absorption at 2265 cm-1 and 3290 cm-1. DBTL was shown to be the best foam catalyst due to higher trimer conversion seen in the spectra by a higher absorption at 1410 cm-1. Acid and base-derived polyols lead to different polyurethane foams with different FTIR spectra, particularly with a higher absorption at 1670 cm-1 for foams from acid-derived liquefaction.

The optical reflection characteristics of asphalt pavement are an important influencing factor in road lighting design, and the macro and micro textures of asphalt pavement significantly affect its reflection characteristics. To investigate the impact of texture parameters on the retroreflection coefficient of asphalt pavement, this study obtained the macroscopic and microscopic texture properties of rutting board specimens and on-site asphalt pavement using a pavement texture tester. The macro- and microtexture parameters, such as macroscopic texture distribution density (D1), microscopic texture distribution density (D2), profile height root-mean-square (Rq), profile slope root-mean-square (Δq), skewness Rsk and kurtosis Rku, were measured, and the corresponding retroreflection coefficient RL was measured using a retro-reflectometer. In the laboratory ex-periments, rutting specimens of AC-13, SMA-13, and OGFC-13 asphalt mixtures were formed. The changes in texture parameters and retroreflection coefficient of different rutting specimens before and after crushing were studied, and a factor influence model between macro- and microtexture parameters and RL was established. And the correlation models of texture index and RL of asphalt pavement are further established. The results showed that in the single factor model, the param-eters can be used to characterize RL with high prediction accuracy, whereas for the on-site meas-urements, the three parameters of Δq, Rsk, and Rku can characterize the RL well. The nonlinear model established on the basis of the B-P neural network algorithm improves its prediction ac-curacy. This research can provide ideas for optimizing the reflection characteristics of asphalt pavement and further provide a decision-making basis for road lighting design.

Regulated deficit irrigation (RDI) strategies aim to improve water usage without reducing yield. Generally, irrigation strategy effectiveness is measured as fruit yield, with little consideration of fruit quality. As water deficit and increased plant cell sclerification often associated, this study explores the effect of RDI on pear fruit stone cells, a crucial factor affecting flesh texture. The presence, distribution and development of pear fruit stone cells under RDI and full irrigation are compared using Pyrus communis L. cv. Barlett trees, employing recently developed microscope image analysis technology. The Control treatment was maintained under non-stress conditions, while the RDI treatment received an average of 15% of Control water during the latter part of Stage I fruit development. Observations at the end of Stage I and at harvest showed no effect on stone cell presence under the tested RDI strategy. Relative area of stone cells within the flesh was greater at Stage I than at harvest, as stone cell expansion occurred early in development while the (unsclerified) parenchyma cells, dominant component of the fruit flesh, expanded until harvest. Stone cell cluster density was higher near the fruit core than in the cortex center and exterior. These initial results suggest that well-planned RDI strategies will generally not affect pear fruit stone cell content and thus, textural quality. Microscope image analysis supported results from previously used analytical techniques, principally chemical, while providing a tool for better understanding the process and timing of stone cell differentiation and thus testing the factors involved.

Speckle noise reduction is an important area of research in the field of ultrasound image processing. Several algorithms for speckle noise characterization and analysis have been recently proposed in the area. Synthetic ultrasound images can play a key role in noise evaluation methods as they can be used to generate a variety of speckle noise models under different interpolation and sampling schemes, and can also provide valuable ground truth data for estimating the accuracy of the chosen methods. However, not much work has been done in the area of modelling synthetic ultrasound images, and in simulating speckle noise generation to get images that are as close as possible to real ultrasound images. An important aspect of simulated synthetic ultrasound images is the requirement for extensive quality assessment for ensuring that they have the texture characteristics and gray-tone features of real images. This paper presents texture feature analysis of synthetic ultrasound images using local binary patterns (LBP) and demonstrates the usefulness of a set of LBP features for image quality assessment. Experimental results presented in the paper clearly show how these features could provide an accurate quality metric that correlates very well with subjective evaluations performed by clinical experts.

Targets detection in synthetic aperture radar (SAR) remote sensing images, which is a fundamental but challenging problem in the field of satellite image analysis, plays an important role for a wide range of applications and is receiving significant attention in recent years. Besides, the ability of human visual system to detect visual saliency is extraordinarily fast and reliable. However, computational modeling of SAR image scene still remains a challenge. This paper analyzes the defects and shortcomings of traditional visual models applied to SAR images. Then a visual attention model designed for SAR images is proposed. The model draws the basic framework of classical ITTI model; selects and extracts the texture features and other features that can describe the SAR image better. We proposes a new algorithm for computing the local texture saliency of the input image, then the model constructs the corresponding saliency maps of features; Next, a new mechanism of feature fusion is adopted to replace the linear additive mechanism of classical models to obtain the overall saliency map; Finally, the gray-scale characteristics of focus of attention (FOA) in saliency map of all features are taken into account, our model choose the best saliency representation, Through the multi-scale competition strategy, the filter and threshold segmentation of the saliency maps can be used to select the salient regions accurately, thereby completing this operation for the visual saliency detection in SAR images. In the paper, several types of satellite image data, such as TerraSAR-X (TS-X), Radarsat-2, are used to evaluate the performance of visual models. The results show that our model provides superior performance compared with classical visual models. By further contrasting with the classical visual models, Our model reduce the false alarm caused by speckle noise, and its detection speed is greatly improved, and it is increased by 25% to 45%.

The present study investigates the role of a simple inerter in supplemental devices for possible implementation in the matured seismic base isolation technique. Firstly, the response of the base-isolated structure with an optimally tuned mass damper-inerter (TMDI) is investigated to see the tuning effects. The time required to tune the TMDI was found to be significantly longer than the duration of a strong-motion earthquake. There was still a reduction in the response of the isolated structure, which is primarily due to the added damping and stiffness (ADAS) of TMDI and not because of the tuning effects. Hence, it is proposed that the corresponding ADAS of the TMDI be directly added to the isolation device. Secondly, the response of the base-isolated structures with the fluid inerter damper (FID) is studied. It was observed that the inerter of the FID does not influence the displacement variance of an isolated structure under broadband earthquake excitation. It implies that the response of the isolated structure with FID is primarily controlled by its counterpart fluid damper (FD). The performance of optimal TMDI, ADAS, FID, and FD to mitigate the seismic response of the flexible multi-story base-isolated structure under real earthquake excitations is also investigated. In terms of suppressing the displacement and acceleration responses of the isolated structure, it has been found that TMDI and ADAS perform similarly. Comparing the response of the isolated structure with FID and FD demonstrated that the inerter in the FID has detrimental effects on the isolated structures, in which the top floor's acceleration and base shear are substantially increased.

Understanding tumor attachments and management of feeding arteries are very important factors to achieve safe resection of skull base meningioma. We examined the distributions and frequencies of feeding arteries in skull base meningioma by cerebral angiography, and also assessed relationships to tumor attachment for skull base meningioma. We enrolled patients with skull base meningioma who underwent MRI and cerebral digital subtraction angiography (DSA), from September 2015 to October 2022. Subjects comprised 115 patients (32 males, 83 females; mean age, 52.7 years) with 117 meningiomas showing tumor attachments around the “cavernous sinus to upper part of the clivus” (Area 1), “lower part of the clivus to foramen magnum” (Area 2), and “tentorium around the petrous bone” (Area 3). We examined feeding arteries based on cerebral angiography and counted the number of related feeding arteries. Particularly frequent arteries, such as the dorsal meningeal artery (DMA), ascending pharyngeal artery (APA), tentorial artery (TA), and petrosal branch (PB) of the middle meningeal artery (MMA) were analyzed for associations of tumor attachment to Areas 1–3. DMA, APA, TA, and PB are very frequent feeding arteries among skull base meningiomas. In some cases, the artery of the foramen rotundum, posterior ethmoidal artery, recurrent meningeal artery, posterior meningeal artery, etc., supply blood to the skull base meningioma. Meningiomas with DMA as a feeding artery correlated strongly with tumor attachment to Area 1 (p&lt;0.001). Meningiomas with APA correlated strongly with tumor attachment to Area 2 (p&lt;0.001). Meningiomas with TA correlated strongly with tumor attachment to Area 3 (p&lt;0.001). PB correlated with Area 3 (p&lt;0.05). Visualization of these arteries suggests tumor attachments to the correlated areas. An accurate anatomical understanding of tumor attachment and feeding arteries is essential to determine appropriate surgical strategies for skull base meningioma. Pre-operative DSA can provide further understanding of the feeding arteries and attachments of skull base meningioma.

The study was conducted in north wollo, south wollo and orimiya zone, in Eastern Amhara with an aim to assess the resource potential of Acacia seyal in the selected sites. The data from the selected sites were collected using point center quarter method. A total of 90 quadrates from nine study areas with plot size 50m*50m, (22.5ha) were systematically located along each transect, 100 m apart, and was spatially captured with the aid of GPS. At every sampling point, four quadrants (90 degrees) were created, using the transect line and a line perpendicular to it. Species composition Acacia seyal structure and its regeneration status, at points along transects were taken to analyze diversity and target species structure of the sites. The highest and least density of Acacia seyal ha^-1 were attained by Mehale mecharie (148) and Alene sefer (52). The highest shannon weiner diversity and species richness was observed in Alene sefer(Kemessie). Acacia seyal structure in all study sites showed an inverted J shape except lastie gerdao (Gubalafeto). Therefore, Acacia seyal deserves immediate conservation and appropriate management measures in order to get sustainable product and services from the species. Based on the results, awareness creation on the values and management of Acacia seyal, study on the management options of Acacia seyal for firewood, fuel wood, charcoal production and also investigation of gum production techniques of Acacia seyal for the sustainable use of the resource are recommended.

The reuse of recycled crushed concrete aggregate (RCCA) and reclaimed asphalt pavement (RAP) can provide a sustainable solution for the disposal of C&amp;D materials instead of sending it to landfill. More importantly, it will save energy and reduce impact on the environment. Several states in USA are using RCCA and RAP as base materials for years, focusing on the quality of the recycled materials. The structure of Recycled Aggregate (RA) is more complex than Natural Aggregate (NA). RAs have old mortar adhered on them that forms a porous surface at interfacial transition Zone (ITZ) and prevents new cement mix from bonding strongly with the aggregates. The objective of this work was to correlate microstructural properties like micro-porosity, inter and intra aggregate pores with the unconfined compressive strength (UCS) of RAP and RCCA molds, mixed at different proportions. In this paper, the quantity of micro-pores and their effect on the strength of mixed materials is used as the basis of microstructural analysis of recycled concrete and reclaimed asphalt. Microstructural properties obtained from the analysis of scanning electron microscope (SEM) images were correlated with unconfined compressive strength. Intra-aggregate and inter-aggregate pores were studied for different ratios of cement treated mixture of RAP and RCCA. The results show that the number of pores in the mixture increases considerably by adding RAP, which eventually causes reduction in unconfined compressive strength. In addition, significant morphological and textural changes of recycled aggregates were observed by SEM image analysis.

Proprotein convertases activate various envelope glycoproteins and participate in cellular entry of many viruses. We recently showed that the convertase furin is critical for the infectivity of SARS-CoV-2. This study investigated the implication of the two cholesterol-regulating convertases SKI-1 and PCSK9 in SARS-CoV-2 entry. We used cell-to-cell fusion assays in HeLa cells and pseudoparticle entry into Calu-3 cells. SKI-1 increases cell-to-cell fusion by enhancing the activation of SREBP-2, whereas PCSK9 reduces cell-to-cell fusion by promoting the cellular degradation of ACE2. Metalloprotease activation is sensitive to enhanced cholesterol levels resulting from SKI-1-activated SREBP-2 that leads to enhanced S2’ formation. However, high metalloprotease activity results in S2’ shedding into a new C-terminal fragment (S2”), leading to reduced cell-to-cell fusion. Indeed, S-mutants that increase S2’’ formation, abolish S2’ and cell-to-cell fusion, as well as pseudoparticles entry, indicating that the formation of S2’’ prevents SARS-CoV-2 cell-to-cell fusion and entry. We next demonstrated that PCSK9 enhanced the cellular degradation of ACE2, thereby reducing cell-to-cell fusion. However, different from the LDLR, a canonical target of PCSK9, the C-terminal CHRD domain of PCSK9 is dispensable for the PCSK9-induced degradation of ACE2. Molecular modeling suggested binding of ACE2 to the Pro/Catalytic domains of mature PCSK9. Thus, both cholesterol-regulating convertases SKI-1 and PCSK9 can modulate SARS-CoV-2 entry via two independent mechanisms.

Kiwifruits are often exposed to various temperature fluctuation (TF) during postharvest storage. To evaluate the effect of TF on the qualities of kiwifruits, fruits were stored at 2 ºC, 2 ºC or 5 ºC (TF2ºC-5ºC), 2 ºC or 7 ºC (TF2ºC-7ºC), alternating every 12 h. Observations revealed that kiwifruits stored at constant 2 °C showed the lowest loss of weight and vitamin C due to the minimum ethylene production and respiratory rate compared to that of TF2ºC-5ºC and TF2ºC-7ºC. Moreover, the results of RT-qPCR verifed that the expression of genes encoding polygalacturonase, β-galacturonidase, and pectin methyl esterase was significantly increased by the treatment of TF. Hence, TF accelerated the degradation of the cell walls, softening, translucency and relative conductivity of the flesh of kiwifruits. Besides, the impact of TF2ºC-7ºC on kiwifruits was more significant relative to TF2ºC-5ºC. The present study provides a theoretical basis for kiwifruit during cold storage.

Global warming has led to the increase in chalky grains of rice, which has also caused the deteriorations of physicochemical and cooking qualities of rice grains. These chalky rice grains are characterized by high α-amylase activity, high protease activity, and low apparent amylose contents, low degree of hardness and stickiness of boiled rice than those of the whole rice grains. In the present paper, we evaluated 14 Japonica unpolished rice grains harvested in Japan in 2021, and these samples (original grains) were divided to two groups (whole grain group and chalky grain one). We found that the chalky rice grains showed higher values of xylanase activity than those of the whole rice grains, while cellulase activity were lower than that of whole rice grains. Using rice grains blended with 30 % of chalky grains as material, we compared sugar and mineral contents and textural properties of the boiled rice grains soaked and boiled in the ordinary water or in the hard water, such as Evian or Contrex. It was shown that the hard water is useful for the prevention of the texture deterioration of the boiled rice grains due to the inhibition of the reduction of endogenous hydrolytic enzymes, such as amylase, proteinase, and xylanase. Furthermore, we found that hard water is useful for the increase of calcium and magnesium intake through the meal with the boiled rice grains soaked and cooked using hard water.

How Nature discovered genetic coding is a largely ignored question, yet the answer is key to explaining the transition from biochemical building blocks to life. Other, related puzzles also fall inside the aegis enclosing the codes themselves. The peptide bond is unstable with respect to hydrolysis. So, it requires some form of chemical free energy to drive it. Amino acid activation and acyl-transfer are also slow and call for catalysis. All living things must thus also convert free energy and synchronize cellular chemistry. Most importantly, functional proteins occupy only small, isolated regions of sequence space. Nature evolved heritable symbolic data processing to seek out and use those sequences. That system has three parts: a memory of how amino acids behave in solution and inside proteins, a set of code-keys to access that memory, and a scoring function. The code-keys themselves are the genes for cognate pairs of tRNA and aminoacyl-tRNA synthetases, AARS. I outline the surprising links between all these questions and the structural duality of the base-pairing that holds genes together and how those links arise from the experiments.

Gelidium jelly was traditionally made by boiling processed Gelidium seaweed and allowing the filtrate to congeal into jelly. The processing of Gelidium seaweed was very complicate involved the repeated procedures of water washing and sun drying for 7 times, and the seaweed was originally purple-red in color turned into yellow after the repeated wash and sun drying. This study aimed to evaluate the effects of halogen lamp drying methods in replace of sun drying on the physical-chemical qualities of Gelidium jellies. Properties included the agar yield, gelling temperature, hardness, springiness, rheological parameters, sensory attributes, color, and volatile compounds were investigated. The results demonstrated halogen lamp drying method required 12 times of washing and drying processes to achieve the similar jelly properties compared to sun drying for 7 times in the experimental conditions. Volatiles including heptanal, β-ionone, and (E)-2-decenal could be used as indicators to monitor the washing and drying processing. Halogen lamp was found could be an alternative processing method for seaweed drying, especially at rainy days.

Texture is essential information for image representation, capturing patterns, and structures. Consequently, texture plays a crucial role in the manufacturing industry and has been extensively studied in the fields of computer vision and pattern recognition. However, real-world textures are susceptible to defects, which can degrade the image quality and cause various issues. Therefore, there is a need for accurate and effective methods to detect texture defects. In this study, a simple autoencoder and Fourier transform were employed for texture defect detection. The proposed method combines Fourier transform analysis with the reconstructed template obtained from the simple autoencoder. Fourier transform is a powerful tool for analyzing the frequency domain of images and signals. Moreover, analyzing the frequency domain enables effective defect detection because texture defects often exhibit characteristic changes in specific frequency ranges. The proposed method demonstrates effectiveness and accuracy in detecting texture defects. Experimental results are presented to evaluate its performance and compare it with those of existing approaches.

Surfaces of additively manufactured metal parts from powder-based processes typically show powder particle agglomerations and other features, resulting in high surface roughness. Proper characterization of those surfaces is necessary in order to assess part quality with respect to coatability, mechanical performance or corrosion resistance for use in aerospace, automotive, medical and more industrial applications. Optical surface texture measurement allows for collection of areal surface data, while the established contact stylus method only captures line profile data. When applying optical methods for surface topography measurements, proper data acquisition and post-processing in order to assess surface texture may be complex. A number of variables can be adjusted, such as different measurement settings, approaches to outlier removal, evaluated area size or form removal. This work shows the influence of selected z-range prior to measurement and the influence of choosing pre-defined outlier removal settings in MountainsMap 9.2 on selected ISO 25178-2:2022 parameters calculated from data obtained from confocal microscopy for as-built Ti6Al4V from laser powder bed fusion. The aim is to show the influence of variation in measurement and post-processing on calculated surface texture parameters and stress the importance of proper documentation in order to achieve reproducibility of data for quality management.

Background: The outbreak of the severe acute respiratory syndrome coronavirus-2 (SARS-CoV-2) resulted in the global COVID-19 pandemic. The urgency for an effective SARS-CoV-2 vaccine has led to the development of a first series of vaccines at unprecedented speed. The discovery of SARS-CoV-2 spike-glycoprotein mutants, however, and consequentially the potential to escape vaccine-induced protection and increased infectivity, demonstrates the persisting importance of monitoring SARS-CoV-2 mutations to enable early detection and tracking of genomic variants of concern. Results: We developed the CoVigator tool with three components: 1) a knowledge base that collects new SARS-CoV-2 genomic data, processes it and stores its results; 2) a comprehensive variant calling pipeline; 3) an interactive dashboard highlighting the most relevant findings. The knowledge base routinely downloads and processes virus genome assemblies or raw sequenc-ing data from the COVID-19 Data Portal (C19DP) and the European Nucleotide Archive (ENA), respectively. The results of the variant calling pipeline are visualized through the dashboard in the form of tables and customizable graphs, making it a versatile tool for tracking SARS-CoV-2 variants. We put a special emphasis on the identification of intrahost mutations and make available to the community what is, to the best of our knowledge, the largest dataset on SARS-CoV-2 intrahost mutations. In the spirit of open data, all CoVigator results are available for download. The CoVigator dashboard is accessible via covigator.tron-mainz.de. Conclusion: With increasing demand worldwide in genome surveillance for tracking the spread of SARS-CoV-2, CoVigator will be a valuable resource of up-to-date list of mutations, which can be incorporated into global efforts to sustainably prevent or treat infections.

A low-profile broadband dual-polarized antenna is investigated for base station applications. It consists of two orthogonal dipoles, fork-shaped feeding lines, an artificial magnetic conductor (AMC), and parasitic strips. By utilizing the dispersion Brillouin diagram, the AMC is designed as the antenna reflector. It has a wide in-phase reflection bandwidth of 54.7% (1.54-2.70 GHz) and a surface wave bound range of 0-2.65 GHz. This design effectively reduces the antenna profile by over 50% compared to traditional antennas without an AMC. For demonstration, a prototype is fabricated for 2G/3G/LTE base station applications. Good agreement between simulations and measurements is observed. The measured -10-dB impedance bandwidth of our antenna is 55.4% (1.58 –2.79 GHz), with a stable gain of 9.5 dBi and high isolation of more than 30 dB across the impedance passband. As a result, this antenna is an excellent candidate for miniaturized base station antenna applications.

To obtain a given structure in 3D building-up modes, it is necessary to use optimal surfacing modes that determine the amount of heat input in local areas. For this purpose, aluminum bronze was surfacing onto a deformed base and the structure and its characteristics in the surfacing and heat-affected zones were studied by the EBSD method. The heterogeneity of the formation of the structure in each selected zone is established, which indicates the heterogeneity of heat input in local areas of the material in one mode of surfacing. For typical cases of crystallization, a molecular dynamics simulation of crystallization processes with different heat input to the base with characteristics specified based on experimental data was carried out. It has been established that the amount of heat input determines the degree of melting and the inherited defectiveness of growing crystals. The formation of misorientation boundaries and crystallization centers of new grains is determined by the conditions of joint growth of grains with given crystallographic parameters of the computational model. Numerical calculations agree with the experimentally observed results.

Many educational institutions are using technology-enhanced learning. However, studies have shown that increased access to technological tools/gadgets is a precursor to incidents of cyberbullying. Using Bronfenbrenner’s Ecological Theory, we explored educators’ knowledge and intervention strategies regarding cyberbullying in schools. The design used in this study was qualitative and descriptive in nature. Purposive sampling technique was used to recruit a sample of eight educators working at secondary school in Johannesburg, South Africa. Data were collected using one-on-one interviews. Thematic analysis method was used to analyse the data. The findings revealed educators had sufficient knowledge of cyberbullying and how it affects learners in schools. However, interventions the teachers had put in place to prevent and manage incidences of cyberbullying were found to be ineffective due to parental disengagement and learners not reporting cases of cyberbullying. Recommendations for enhancing management of cyberbullying cases are provided.

(1) Background: High blood pressure is one of the symptoms of stroke, the Self Care Deficit theory by Dorothea Orem focuses on a person's ability to care for himself independently so that the ability to maintain his health and well-being is achieved. There are currently 600 million hypertensive patients worldwide, of which 3 million die every year. Uncontrolled high blood pressure can lead to a 7-fold increase in the chances of stroke. The existence of this condition can be minimized in patients through several innovative interventions, one of which is foot massage. This study aims to determine the effectiveness of stretching and foot massage with lavender oil in stabilizing high blood pressure in stroke patients.(2) Methods: The method used in this research is descriptive. The subjects of this case study were selected according to the inclusion and exclusion criteria of the journal Evidence-Based. Subjects included intervention patients and control patients. Foot massage therapy with lavender oil is done 2 times a day for 10-15 minutes using the effleurage technique after showering in the morning and evening. Stretching is done 2 times a day every 10-15 minutes.(3) Results: The results of the analysis showed that there was a change in blood pressure after the application of stretching and foot massage with lavender oil. From the initial examination, the results showed that the blood pressure of 170/100 mmHg decreased to 140/90 mmHg and the pain scale decreased from 4 to 0.

Deep neural networks (DNN) have successfully delivered a cutting-edge performance in several fields. With the broader deployment of DNN models on critical applications, the security of DNNs becomes an active and yet nascent area. Attacks against DNNs can have catastrophic results, according to recent studies. Poisoning attacks, including backdoor and Trojan attacks, are one of the growing threats against DNNs. Having a wide-angle view of these evolving threats is essential to better understand the security issues. In this regard, creating a semantic model and a knowledge graph for poisoning attacks can reveal the relationships between attacks across intricate data to enhance the security knowledge landscape. In this paper, we propose a DNN Poisoning Attacks Ontology (DNNPAO) that would enhance knowledge sharing and enable further advancements in the field. To do so, we have performed a systematic review of the relevant literature to identify the current state. We collected 28,469 papers from IEEE, ScienceDirect, Web of Science, and Scopus databases, and from these papers, 712 research papers were screened in a rigorous process, and 55 poisoning attacks in DNNs were identified and classified. We extracted a taxonomy of the poisoning attacks as a scheme to develop DNNPAO. Subsequently, we used DNNPAO as a framework to create a knowledge base. Our findings open new lines of research within the field of AI security.

The next generation of wireless and mobile networks will have to handle a significant increase in traffic load compared to the actual one. This situation calls for novel ways to increase spectral efficiency. Therefore in this paper, we propose a wireless spectrum hypervisor architecture that abstracts a radio frequency (RF) front-end into a configurable number of virtual RF front-ends. The proposed architecture has the ability to enable flexible spectrum access in existing wireless and mobile networks, which is a challenging task due to the limited spectrum programmability, $i.e.$, the capability a system has to change the spectral properties of a given signal to fit an arbitrary frequency allocation. The main goal of the proposed approach is to improve spectral efficiency by efficiently using vacant gaps in congested spectrum-bandwidths or adopting network densification through infrastructure sharing. We demonstrate mathematically how our proposed approach works and present several simulation results proving its functionality and efficiency. Additionally, we designed and implemented an open-source and free proof of concept prototype of the proposed architecture, which can be used by researchers and developers to run experiments or extend the concept to other applications. We present several experimental results used to validate the proposed prototype. We demonstrate that the prototype can easily handle up to 12 concurrent physical layers.

Bioactive peptides are promising cosmetic active ingredients that can improve skin health and appearance. They exhibit a broad spectrum of activity, including anti–ageing, antioxidant, antimicrobial and anti–inflammatory. The aim of this study was to develop a safe, stable and efficacious environmentaly friendly ("green") emulsion using milk protein hydrolysate as a model active ingredient. Potential emulsions were formulated with biodegradable emollients, stabilised with a naturally-derived mixed emulsifier and prepared by cold process. They were evaluated for rheological behavior (continuous rotation and oscillation tests), physical stability (dynamic mechanical thermal analysis - DMTA test) and texture profiles, as well as for cytotoxic, antioxidant and antimicrobial effects. Rheological characterization revealed shear-thinning flow behaviour with yield point from continuous rotation tests and predominantly elastic character from oscillation (amplitude and frequency sweep) tests, with small structural change detected in the DMTA test. These results implied satisfactory rheological properties and good stability. Texture analysis revealed acceptable spreadability and substantivity of the emulsions. The protein hydrolysate showed antioxidant activity. The developed emulsions showed low antibacterial activity against selected microorganisms, but this was due to the action of preservatives, not peptides. All potential emulsions showed desirable safety profile. The results obtained provide the basis for the next stage of formulation development, i.e. in vivo efficacy tests.

The texture properties of cooked rice are a dominant property which can indicate the eating quality. Evaluation of back extrusion (BE) test precision and sensitivity for cooked germinated brown rice (GBR) texture in production process was investigated in this study. BE test on texture properties of cooked GBR rice show high precision of measurement of hardness, toughness and stickiness tests which indicated by the repeatability and reproductivity test but the sensitivity indicated by coefficient of variation of the texture properties. The findings of the study of the effect of different soaking and aging duration in the production of Khao Dawk Mali 105 (KDML 105) GBR on cooked GBR texture measured by BE test confirmed the developed protocol for evaluation of high precision and sensitivity of the texture measurement method. Repeatability and reproducibility of reliable measurements have a low standard deviation of the farthest different between replicates, which is considered high precision. High coefficient of variation where the relative wide variation of the absolute value of the property can be detected indicate high sensitivity which even small resolution can be detected or vice versa. But the correlation coefficient among the texture properties by BE were not related to the precision or sensitivity of the test. By these results, the original protocol for determination of precision and sensitivity of food texture measurement was successfully verified as the usable evaluation protocol for GBR texture measurement.

Eight samples of limestones and marbles were studied by neutron diffraction to collect 2 Quantitative Texture (i.e., Crystallographic Preferred Orientations or CPO) of calcite deforming at 3 different depths in the crust. We studied the different Texture patterns developed in shear zones at 4 different depth and their influence on seismic anisotropies. Samples were collected in the French and 5 Italian Alps, Apennines, and Paleozoic Sardinian basement. They are characterized by isotropic to 6 highly anisotropic (e.g., mylonite shear zone) fabrics. Mylonite limestones occur as shear zone horizons 7 within the Cenozoic Southern Domain in Alpine thrust-and-fold belts (Italy), the Briançonnais domain 8 of the Western Alps (Italy-France border), the Sardinian Paleozoic back-thrusts or in the Austroalpine 9 intermediate units. The analyzed marbles were collected in the Carrara Marble, in the Austroalpine Units 10 in the Central (Mortirolo) and Western Alps (Valpelline). The temperature and depth of development of fabrics vary from < 100◦C, to 800◦C and depth from <10 km to about 30 km, corresponding from upper 12 to lower crust conditions. Quantitative Texture Analysis shows different types of patterns for calcite: 13 random to strongly textured. Textured types may be further separated in orthorhombic and monoclinic 14 (Types A and B), based on the angle defined with the mesoscopic fabrics. Seismic anisotropies were 15 calculated by homogenizing the single crystal elastic tensor, using the Orientation Distribution Function 16 calculated by the Quantitative Texture Analysis. The resulting P- and S-waves anisotropies show a wide 17 variability due to the textural types, temperature and pressure conditions, and dip of the shear planes.

: The effect that the microstructure exerts on the TRIP phenomenon and on the mechanical properties in a multiphase steel was studied. Samples of an initially cold-rolled ferrite-pearlite steel underwent different intercritical annealing treatments at 750 °C until an equal fractions of austenite/ferrite was reached; the intercritical treatment was followed by isothermal bainitic treatments before cooling the samples to room temperature. Samples in the first treatment were heated directly to the intercritical temperature, whereas other samples were heated to either 900 or 1100 °C to obtain a fully homogenized, single phase austenitic microstructure prior to the conducting the intercritical treatment. The high temperature homogenization of austenite resulted in the decrease in its stability, so a considerable austenite fraction transformed into martensite by cooling to room temperature after the bainitic heat treatment. Most of the retained austenite transformed during the tensile tests, and as a consequence, the previously homogenized steels showed the highest UTS. In turn, the steel with a ferritic-pearlitic initial microstructure, exhibited higher ductility than the other steels and texture components that favor forming processes.

The present study produced and characterised chitosan, chitosan nanoparticle, chitosan n – benzaldehyde Schiff base, chitosan nanoparticle n – benzaldehyde Schiff base, Fe(III) chitosan n – benzaldehyde Schiff base and Fe(III) chitosan nanoparticle n – benzaldehyde Schiff base for biomedical application as antimicrobial agents. The materials were characterized with Fourier Transform Infrared spectroscopy, X-ray Diffractogram and biologically evaluated using disc diffusion method with three gram-positive bacteria. The FTIR absorption peaks were shifted to a lower wave number than the micro materials from which it was modified. These clearly indicate the linkage between phosphate, ammonium ion, Schiff base and Fe(III) metal. The diffracted peaks of Fe(III) chitosan nanoparticle n – benzaldehyde Schiff base were new peaks at 2θ = 24o and 42o when compare to the peak of Fe(III) chitosan n – benzaldehyde Schiff base of 2θ = 22.5o and 34o. The difference in peak shift were attributed to the ionic bonding of the complexation of Fe(III) with the blending of benzaldehyde to chitosan – Tpp backbone structure. Fe(III) chitosan nanoparticle Schiff base has more antimicrobial activity against same bacteria and fungi tested than Fe(III) chitosan n – benzaldehyde Schiff base, chitosan n – benzaldehyde Schiff base and chitosan. The antimicrobial activities of the synthesised six materials shown that the materials have high activities than the above – mentioned standard drugs.

Sickle cell disease is characterized by stiff, “sickled” red blood cells that have difficulty moving through the bloodstream and do not efficiently carry oxygen. It is an inherited disease with severely limited treatment options, and is caused by a point mutation. Its prevalence in black and brown communities makes the already limited treatment options even less accessible. Base editing and prime editing are two relatively recent discoveries in the field of genome editing and were developed after the groundbreaking discovery of the CRISPR Cas9 system. While not fully tested, they hold a lot of promise in providing alternative treatment options for sickle cell disease. Both editing systems are able to install individual point mutations in the beta globin gene, which is where the sickle cell mutation occurs, and can thus cure sickle cell disease (in theory). In this paper we outline the mechanisms of CRISPR-Cas9 systems and base and prime editing, and provide insight into how to apply them to treat SCD. Further investigation should be done on specific editing systems and designs to use to ensure optimal treatment of SCD.

This paper is devoted to an accurate determination of the London dispersive and polar free energy of adsorption, the two Lewis acid γs+ and base γs- components of polar surface energy γsAB of 2D single-crystalline and polycrystalline covalent organic frameworks such as TAPPy-TPA-COFs. Inverse gas chromatography (IGC) at infinite dilution was used to quantify the different surface parameters of the different materials. From IGC measurements, one determined the net retention time of the adsorption of n-alkanes and several polar solvents on single-crystalline and polycrystalline covalent organic frameworks. The free surface Gibbs energy of adsorption was obtained for the various organic molecules at different temperatures from their net retention volume values. The separation between the London dispersive energy and the polar energy of adsorbed molecules was carried out by using a new thermodynamic parameter PSX chosen as new indicator variable and taken into account the deformation polarizability and the harmonic mean of the ionization energies of solvents and solid materials, derived from London dispersion equation. The obtained results are very promising for the accurate determination of the surface thermodynamic parameters of adsorption of organic solvents on solid surfaces.

The location routing problem of unmanned aerial vehicles (UAV) in border patrol for intelligence, surveillance and reconnaissance is investigated, where the location of UAV base stations and the UAV flying routes for visiting the targets in border area are jointly optimized. The capacity of the base station and the endurance of the UAV are considered. A binary integer programming model is developed to formulate the problem, and two heuristic algorithms combined with local search strategies are designed for solving the problem. The experiment design for simulating the distribution of stations and targets in border is proposed for generating random test instances. Also, an example based on the Sino-Vietnamese border is presented to illustrate the problem and the solution approach. The performance of the two algorithms are analyzed and compared through randomly generated instances.

With the increase in occupation-specific risks of lip cancer associated with solar radiation, there is a need for developing photoprotective lipsticks to protect skin against harmful effects of UV radiation. Considering the unique chemical and physical properties of low-molecular-weight organogelators (LMOGs), the present study intended to assess the UV protective properties of LMOGs-based lipstick formulations. In this study, dibenzylidene-D-sorbitol (DBS) and 12-hydroxystearic acid (12-HSA) were used to formulate lipsticks : L1 (1% DBS), L2 (10% 12-HSA), L3 (1.5% DBS) and L4 (control, no LMOGs). The lipstick formulations were tested for in vitro sun protection factors (SPF), UVA protection factor (UVA-PF), thermal, mechanical and texture analyses. Lipsticks with LMOGs exhibited higher UVA-PF and SPF, and more particularly 12-HSA-based lipstick. Results showed also the viscoelastic and heat-resistant properties of LMOGs and their effect of increasing pay-off values. In general, texture analysis indicating that 12-HSA-based lipstick was significantly harder to bend compared to control, while other formulations became softer and easier to bend throughout the stability study. Finally, sensorial and instrumental analyses permitted to classify lipsticks into two groups. This work suggests the potential use of LMOGs as a structuring agent for lipsticks paving the way towards more photoprotective and sustainable-derived alternatives.

700 MPa grade Ti and Nb-Ti microalloyed steels produced by thermo-mechanical control rolled processes (TMCP) were studied to elucidate texture that contributes to delamination and consequent impact toughness. The microstructure of Ti and Nb-Ti steels consisted of ferrite and bainite. Compared with Ti steel, Nb-Ti steel was characterized by a microstructure with finer ferrite and more bainite. The results from tensile and impact tests indicated that there is insignificant change in tensile properties, but toughness was greater in Nb-Ti steel compared with Ti steel. More severe delamination in Nb-Ti steel is attributed to stronger α-fiber (RD ||<110>) texture than Ti steel, especially {100}<110>, {113}<110> and {112}<110> texture. Typical cleavage river patterns were not observed on delaminated fracture surface, instead the cleavage fracture surface indicated some dimples. Interestingly, the impact energy of samples with delamination was greater than samples without delamination in the ductile–brittle transition region. The study suggests that delamination in the ductile–brittle transition zone may also be representative of high toughness.

In this paper were analyzed the effects of double reduction and annealing during rolling process on texture evolution in an ultrathin sheet of low carbon steel. Experimental samples were obtained from each process stage. EBSD technique and correlated tools as orientation density functions and pole figures were used to analyze the microstructural changes and the texture. Results show that {111} recrystallized grains were formed during process, reducing dramatically gamma-fibre texture intensity and generating an adequate finished product for deep die stamping.

In this paper, a circularly polarized broadband slot antenna is designed for base station applications. The antenna is built on a square-shaped FR4 Epoxy substrate that measures 60mm in length and 1mm in height with a relative permittivity of 4.4. The ground plane has a recessed slot, and the feeding mechanism employs an offset microstrip line. The slot enables circular polarization and optimal impedance matching, which are enhanced further by offset feeding and the addition of stubs to create a composite-shaped patch. With an impedance bandwidth of 106% (1.28 GHz-4.16 GHz) and an axial ratio bandwidth of 69% (1.71 GHz-3.51 GHz), the CP broadband slot antenna effectively covers popular mobile communication bands such as GSM 1800, GSM 1900, 3G/LTE 2100, 3G/LTE 2300, 4G/LTE 2500, and 2.4 GHz Wi-Fi bands. The maximum gain is simulated to be 3.5 dB.

Raindrop size distribution (RSD) is an index for reflecting precipitation characteristics. Analyzing the differences of RSD plays an important role in understanding the precipitation microphysical processes and improving quantitative precipitation prediction of radar. In this paper, the RSD data of Dafang (57708) station, Majang (57828) station, and Luodian (57916) station (with an altitude of 1722.7m, 985.0m, and 441.5m, respectively) in Guizhou are analyzed according to the precipitation microphysical characteristics. First,Particles with particle size less than 1mm contributes the highest value to the density of particle number , and decrease with the descending altitude. Second, the GAMMA distribution fit shows a better fit compare to M-P distribution fit, and GAMMA distribution fit increases with the ascending altitude. Third, the mass-weighted average diameter is not sensitive enough to the change of precipitation intensity with correlation coefficients of 54.84%, but there is a obvious relationship between the average volume diameter and the precipitation intensity with correlation coefficients of 69.15%. Then, the precipitation prediction model is established using LSTM neural network after fusing the representative microphysical characteristics of RSD with radar and rain gauge data. The precipitation prediction model is applied to the Dafang (57708) site to predict precipitation for time range of 0-180 minutes, and it is found that for the prediction of convective cloud and stratiform cloud precipitation, the 60-minute prediction results are the most consistent with the actual precipitation, where the correlation coefficients are 92.87% and 92.57%, respectively. Conclusively, the results demonstrate that combining with the RSD base data could improve the reliability of precipitation forecasting.

Simple Learning Motivations Hierarchy Model (SLMHM) is a theory that attempts to structure the path of learning “growth” with 16 levels where each next level corresponds to higher aims, motives, results, and satisfaction of needs. The SLMHM has been developed to simplify design, control, and evaluate the learning processes. The SLMHM was first presented at IES-2020 Conference (Gakh, 2020). More detailed research including analysis of internal structure shows that the model should be corrected. The “Plan-Do-Check-Act” cycle (PDCA Cycle) is popular in management. This paper describes the SLMHM improvements based on analyses of its similarities with the PDCA Cycle. The description of this research makes SLMHM more comprehend.

This paper presents a multifunctional reflective digital metasurface of arbitrary base based on voltage tunable liquid crystal (LC). The reflective digital metamaterial can be multiplexed for different desirable functions by properly biasing the LC for different code patterns. Simulation results of three significant functions, beam steering with a steering elevation angle 27° at 75 GHz, RCS reduction of at least 15dB along the incident direction, and beam shaping with different beam shapes have been presented to prove the concept.

Bone growth plate abnormalities and skull shape defects are seen in hypophosphatasia, a heritable disorder in humans that occurs due to deficiency of Tissue Nonspecific Alkaline Phosphatase (TNAP, Alpl) enzyme activity. Abnormal development of the cranial base growth plates (synchondroses) and abnormal skull shapes have also been demonstrated in global TNAP-/- mice. To distinguish local vs. systemic effects of TNAP on skull development, we utilized P0-Cre to knockout TNAP only in cranial neural crest derived tissues using TNAP flox mice. Here we show that TNAP deficiency in cranial neural crest leads to leads to skull shape defects and deficient growth of the intersphenoid synchondrosis (ISS). ISS chondrocyte abnormalities included increased proliferation in resting and proliferative zones with decreased apoptosis in hypertrophic zones. ColX expression is increased, indicative of premature differentiation in the absence of TNAP. Sox9 expression is increased in both resting and prehypertrophic zones of mutant mice. Expression of PTHrP and IHH were also increased. Finally, cranial base organ culture revealed that inorganic phosphate (Pi) and pyrophosphate (PPi) have specific effects on cell signaling and phenotype changes in the ISS. Together, these results demonstrate that TNAP expression in growth plate chondrocytes is essential for normal development, and that the mechanism likely involves Sox9, PTHrP, IHH and PPi.

The reflectance $R$ of monolayer graphene for the normal incidence of electromagnetic radiation is known to be remarkably defined only by $\pi$ and the fine-structure constant $\alpha$. It is shown in this paper that the reflectance (or the sum of transmittance and absorptance) of monolayer graphene, expressed as a quadratic equation with respect to the fine-structure constant $\alpha$ must unsurprisingly introduce the 2$^\text{nd}$ fine-structure constant $\alpha_2$, as the 2$^\text{nd}$ root of this equation, as well as two $\pi$-like constants for a convex and a saddle surface. It turns out that this 2$^\text{nd}$ fine-structure constant is negative, and the sum of its reciprocal with the reciprocal of the fine-structure constant $\alpha$ is independent of the reflectance value $R$ and remarkably equals $-\pi$. Particular algebraic definition of the fine-structure constant $\alpha^{-1} = 4\pi^3 + \pi^2 + \pi \approx 137.036$, containing the free $\pi$ term and agreeing with the physical definition of this dimensionless constant to the 5$^\text{th}$ significant digit, when introduced to this sum, yields $\alpha_2^{-1} = -4\pi^3 - \pi^2 - 2\pi \approx -140.178$. Assuming universal validity of the physical definition of $\alpha$, $\alpha_2$ defines the negative speed of light in vacuum $c_n$. The average of this speed $c_n$ and the speed of light in vacuum $c$ is in the range of the Fermi velocity ($10^6$ m/s). Furthermore, the 2$^\text{nd}$ negative fine-structure constant $\alpha_2$ alone introduces the imaginary set of base Planck units.