In this study, an alternative method to conventional production methods involving thin section copper permanent mould casting (rapid solidification), hot rolling and heat treatment processes to manufacture AISI DC 53 cold work tool steel, has been investigated. In this new method, solidification of the AISI DC 53 was done in the thin section copper mould instead of traditional ingot casting. After solidification, thin slabs obtained was homogenized to 1150 ^oC and hold at this temperature for one hour and then hot rolling was be applied. During hot rolling process, about % 30 reduction in thickness of slab was obtained. After hot rolling, heat treatment (austenitizing, quenching and tempering) have been applied to thin slab. The samples have been taken as cast, as rolled and as heat treated (austenitized and tempered) and the microstructural analysis, hardness tests, retained austenite quantity measurement by XRD method have been performed. The heat treatment and tests have been performed for a commercially available AISI DC 53 which is manufactured by thick section ingot casting and rolling. Hardness values of the AISI DC 53 steels produced by traditional route is in the range of 52-54 HRC after austenitization at 1025 ^oC for one hour and quenched in compressed air and tempered twice at 525 ^oC for 120 mins. On contrary the permanent mould cast AISI DC 53 after homogenization at 1150 ^oC and immediately hot rolling then air cooling and austenitized at 1025 ^oC for one hour then quenched by compressed air and tempered twice at 525 ^oC for 120 mins have hardness valeus in the range of 55-57 HRC. Experiments have revealed that the properties of new rapid solidified steel in permanent copper mould are better than the commercially available steel and have a more refined microstructure than commercially produces alternative. Therefore, the new proposed method can be used as an alternative manufacturing method for cold-work tool steels.

Shear dynamics simulation under extreme pressure was used to optimise the composition of ester-based lubricant base oil and extreme pressure additives. As a result, the ester-based lubricant in the weak-gel drilling fluid achieves reduction and increases the efficiency in drilling construction, and the field operation efficiency improves. The results of base oil lubrication simulation show that three base oils, namely, methyl oleate, ethyl oleate and butyl oleate, can be stably adsorbed on the surface layer of the shear surface. Methyl oleate has the lowest system temperature after shear stabilisation and has a high load-bearing capacity. The shear stress of methyl oleate decreases by changing the initial shear temperature and speed. It increases by 6.36 MPa when the speed increases from 10 m/s to 30 m/s. At this time, the shear stress of butyl oleate increases by 10.11 MPa. The results of the four-ball friction experiments show that the radius of the abrasion spot of methyl oleate is 179.83 μm, which is smaller than that of the other two base oils. Moreover, the friction coefficient of methyl oleate is 0.0018, which is approximately 1/3 of that of butyl oleate. Methyl oleate has better lubrication efficiency. The shear simulation results are consistent with the experimental results. The simulation can be used for the molecular design of lubricant materials. The oleic acid amide–containing amine group and the glyceride oleic–containing hydroxyl group were selected as the extreme pressure functional components for shear simulation. Results show that the shear stress of oleic acid amide is much lower than that of oleic acid glyceride when the initial shear temperature and speed change. The extreme pressure lubrication component–containing amine group is better than the extreme pressure lubrication material–containing hydroxyl group. The effects of different oleamide contents in the two-component mixtures on the lubricating properties were investigated through shear simulation, with methyl oleate as the base oil and oleamide as the extreme pressure functional component. The simulation results show that the lubricant has the optimal shear stress when 10% oleamide is added to the lubricant. The base properties of the lubricant were tested using a mixture of 90% methyl oleate and 10% oleamide, formulated as a lubricant. Results show that the friction coefficient can be reduced to 0.03 when 0.5% of the lubricant is added to the base mud. Moreover, the lubricant film formed shows high strength. Then, 1% lubricant was added to the weak-gel drilling fluid to evaluate the effect of the lubricant on the gel structure of the drilling fluid. Results show that adding lubricant does not affect the rheological properties of the drilling fluid. The gel structure of the system also remains stable even after 7 days of continuous ageing. The results of the field experiments in Hua3-01 well show that adding 1% ester-based lubricant to the field drilling fluid reduces the drilling friction by 33%. Thus, the efficiency of directional side drilling can be effectively improved, complicated accidents, such as poor starting and stopping of drilling and stuck jamming, can be avoided, and the goals of reducing quantity and increasing efficiency can be completed.

Bladder cancer (BC) diagnosis is reliant on cystoscopy, an invasive procedure associated with urinary tract infections. This has sparked interest in identifying non-invasive biomarkers in body fluids such as blood and urine. A source of biomarkers in these biofluids are extracellular vesicles (EVs), nanosized vesicles that contain a wide array of molecular cargo, including small non-coding RNA such as microRNA and transfer RNA-derived fragments (tRF). Here we performed small-RNA next-generation sequencing for urine EVs, serum EVs and serum supernatant from 41 patients with non-muscle invasive BC (27 stage Ta, 14 stage T1) and 15 non-cancer patients (NCP) with benign cystoscopy findings. Serum and urine samples were collected before transurethral resection of bladder tumors (TUR-b) and at routine postsurgery check-ups. Expression levels of tRFs in presurgery samples were compared to those at postsurgery check-ups and to NCPs. To strengthen the reliability of our results, samples from 10 patients with stage T1 disease were resequenced. When comparing tRF expression in urine EVs between BC patients with stage T1 disease and NCPs, 14 differentially expressed tRFs (DEtRFs) were identified. In serum supernatant, six DEtRFs were identified among stage T1 patients when comparing presurgery to postsurgery samples, and four DEtRFs were found when comparing presurgery samples to NCPs. By performing a blast search, we found that sequences of DEtRFs aligned with genomic sequences pertaining to processes relevant to cancer development, such as enhancers, regulatory elements and CpG islands. Our findings display a number of tRFs that may hold potential as biomarkers for the diagnosis and recurrence-free survival of BC.

Accurate and consistent rainfall observations are vital for climatological studies in support of better planning and decision making. However, estimation of accurate spatial rainfall is limited by sparse rain gauge distributions. Satellite rainfall products can thus potentially play a role in spatial rainfall estimation but their skill and uncertainties need to be under-stood across spatial-time scales. This study aimed at assessing the temporal and spatial performance of seven satellite products (TARCAT (Tropical Applications of Meteorology using SATellite and ground-based observations (TAMSAT) African Rainfall Climatology And Time series), Climate Hazards Group InfraRed Precipitation with Station data (CHIRPS), Tropical Rainfall Measuring Mission (TRMM-3B43), Climate Prediction Center (CPC) Morphing (CMORPH), the Precipitation Estimation from Remotely Sensed Information using Artificial Neural Networks- Climate Data Record (PERSIANN-CDR), CPC Merged Analysis of Precipitation (CMAP) and Global Precipitation Climatology Project (GPCP) using gridded (0.05o) rainfall data over East Africa for 15 years(1998-2012). The products’ error distributions were qualitatively compared with large scale horizontal winds (850 mb) and elevation patterns with respect to corresponding rain gauge data for each month during the ‘long’ (March-May) and ‘short’ (October-December) rainfall seasons. For validation only rainfall means extracted from 284 rain gauge stations were used, from which qualitative analysis using continuous statistics of Root Mean Squared Difference, Standard deviations, Correlations, coefficient of determinations (from scatter plots) were used to evaluate the products’ performance. Results revealed rainfall variability dependence on wind flows and modulated by topographic influences. The products’ errors showed seasonality and dependent on rainfall intensity and topography. Single sensor and coarse resolution products showed lowest performance on high ground areas. All the products showed low skills in retrieving rainfall during ‘short’ rainfall season when orographic processes were dominant. CHIRPS, CMORPH and TRMM performed well, with TRMM showing the best performance in both seasons. There is need to reduce products’ errors before applications.

This paper comprehensively reviews sensors and sensing devices developed or/and proposed so far utilizing two smart materials: electrorheological fluids (ERFs) and magnetorheological materials (MRMs) whose rheological characteristics such as stiffness and damping can be controlled by external stimuli, an electrical voltage for ERFs and a magnetic field for MRMs, respectively. In this review article, the MRMs are classified into magnetorheological fluid (MRF), magnetorheological elastomer (MRE) and magnetorheological plastomer (MRP). To easily understand the history of sensing research using the two smart materials, the order of this review article is organized in a chronological manner of ERF sensors, MRF sensors, MRE sensors and MRP sensors. Among many sensors fabricated from each smart material, one or two sensors or sensing devices are adopted to discuss on the sensing configuration, working principle and specifications such as accuracy and sensitivity. Some sensors adopted in this article include force sensor, tactile device, strain sensor, wearable bending sensor, magnetometer, display device and flux measurement sensor. After briefly describing what have been reviewed in a conclusion, several challenging future works, which should be done for practical applications as sensors or sensing devices, are remarked in terms of new technologies such as artificial intelligence neural network in which several parameters affecting the sensor signals can be precisely tuned or controlled. It is sure that this review article is very helpful to make creative sensors using not only the proposed smart materials but also several different types of smart materials including shape memory alloys and active polymers.

In the Netherlands, the assessment of existing prestressed concrete slab-between-girder bridges showed that the thin, transversely prestressed slabs may be critical for static and fatigue punching when evaluated using the recently introduced Eurocodes. On the other hand, compressive membrane action increases the capacity of these slabs and changes the failure mode from bending to punching shear. To improve the assessment of the existing prestressed slab-between-girder bridges in the Netherlands, two 1:2 scale models of an existing bridge, the Van Brienenoord Bridge, were built in the laboratory and tested monotonically as well as under cycles of loading. The result of these experiments is: 1) the static strength of the decks, showing that compressive membrane action significantly enhances the punching capacity, and 2) the Wöhler curve of the decks, showing that compressive membrane action remains under fatigue loading. The experimental results can then be used for the assessment of the most critical existing slab-between-girder bridge. The outcome is that the bridge has sufficient punching capacity for static and fatigue loads, and thus that the existing slab-between-girder bridges in the Netherlands fulfil the code requirements for static and fatigue punching.

We delve into the intricate dynamics governing anisotropic fluids within the cosmological paradigm, elucidating the nuanced influence of conformal anomalies upon the stress-energy tensor. Through the presentation of a sophisticated theoretical framework, we seamlessly intertwine unconventional fluidic properties with profound cosmological considerations, thereby augmenting and refining our comprehension of the primordial universe.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Living cells are complex systems that may be characterized by fluids crowded by hundreds of different elements in particular by a high density of polymers; they are an excellent and challenging laboratory to study exotic emerging physical phenomena where entropic forces emerge from organization processes of many-body interactions. The competition between microscopic and entropic forces may generate complex behaviors like phase transitions that living cells may use to accomplish their functions. In the era of the big data, when biological information abounds but general principles and precise understanding of the microscopic interactions scarce, the entropy methods may offer significant information. In this work we develop a model where the thermodynamic equilibrium results from the competition between an effective electrostatic shortrange interaction and the entropic forces emerging in a fluid crowded by different size polymers. The target audience for this article are interdisciplinary researchers in complex systems, particularly in thermodynamics and biophysics modeling.

A lightweight composite bridge deck system composed of steel orthotropic deck stiffened with thin Ultra-High Performance Concrete (UHPC) layer is developed to eliminate fatigue cracks in orthotropic steel decks. During the construction and operation period of the bridge, the debonding between the steel deck and the UHPC layer may introduce the several issues, such as crack-induced water invasion and distinct reduction of the shear resistance. In the study, an effective and novel non-destructive interface condition monitoring approach using piezoelectric lead zirconate titanate (PZT)-based technologies is proposed to detect interfacial delamination between steel deck and UHPC layer. Experimental tests are performed on several steel-UHPC composite slabs and a conventional steel-concrete composite slab. The thin styrofoam sheets with different sizes and thicknesses are set on different locations of the steel deck as the artificial debondings. The PZT ceramic patches are bonded on the surfaces of the steel deck and UHPC layer as the actuators/sensors. An improved PSO (Particle Swarm Optimization)-K-means clustering algorithms is proposed to obtain the debonding patterns based on the feature data set. The laboratory tests demonstrate that the proposed approach provides an effective and accurate way to detect interfacial debonding of steel-UHPC composite slab.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

A field theoretic representation of the classical partition function is derived for a system composed of a mixture of anisotropic and isotropic mobile charges that interact via long range Coulomb and short range nematic interactions. The field theory is then solved on a saddle-point approximation level, leading to a coupled system of Poisson-Boltzmann and Maier-Saupe equations. Explicit solutions are finally obtained for a calamitic counterion-only system in proximity of a charged planar wall. The nematic order parameter profile, the counterion density profile and the electrostatic potential profile are interpreted within the framework of a nematic-isotropic wetting phase with a Donnan potential difference.

This paper proposes a curved link-slab (CLS) structure, simplified into a hingeless-arch model, to address the current cracking phenomenon of CLS concrete. The stress formula of the hingeless arch under various loads is derived based on the classical mechanic's method. Based on an actual bridge example, the mechanical properties of CLS are analyzed under different loads and load combinations. The results show that: (1) the CLS stress is significantly lower than that of the flat link-slab structure (FLS), (2) its stress values are less than the concrete tensile limit, and (3) the CLS can effectively solve the concrete cracking phenomenon on the link-slab. The rationality of the stress formula derived from the simplified model of the hingeless arch is verified using the finite element method (FEM). The parametric sensitivity analysis shows that variation of the reinforcement ratio of the CLS has a limited impact on it. Considering both the concrete tensile and compressive limit, the thickness of the CLS should be 15 cm to 20 cm, and its design span should be about 5% to7.5% of the main beam length.

A four-step synthesis of bifunctional, noncovalent organocatalysts based on the chiral (1R,2R)-cyclohexane-1,2-diamine scaffold containing a 1,2-benzenediamine H-bond donor was developed. Nucleophilic aromatic substitution of the 2-fluoronitrobenzene derivative with the commercial (1R,2R)-cyclohexane-1,2-diamine was followed by selective alkylation of the primary amino group, reduction of the aromatic nitro group and final derivatization of the primary aromatic amino group, i.e. acylation, sulfonation, reductive alkylation and arylation, leading to the four subtypes of organocatalysts. All new compounds were fully characterized. The prepared organocatalysts (32 examples) were tested in the Michael addition of acetylacetone to trans-β-nitrostyrene, yielding the addition product with incomplete conversions (up to 93%) and enantioselectivities of up to 41% ee.

Recent studies have elucidated the diversity of genes encoding venom in sea anemones. However, most of those genes are yet to be explored in an evolutionary context. Insulin is a common peptide across metazoans and has been coopted into a predatory venom in many venomous lineages. In this study, we focus on the diversity of insulin-derived venoms in sea anemones and on elucidating their evolutionary history. We sourced data for 34 species of sea anemones and found sequences belonging to two venom families that have Insulin PFAM annotations (Cono-Insulin, VP302). Our findings show that both families have undergone duplication events. Members of each of the independently evolving clades have consistent predicted protein structures and distinct dN/dS values. Our work also shows that VP302 is part of a multidomain venom contig and has experienced a secondary gain into the venom system of cuticulate sea anemones.

Thin Slab Casting and Directing Rolling (TSCDR) has become a major process for flat- rolled production. However, the elimination of slab reheating and limited number of thermomechanical deformation passes leave fewer opportunities for austenite grain refinement resulting in some large grains persist in the final microstructure. In order to achieve excellent Ductile to Brittle Transaction (DBTT) and Drop Weight Tear Test (DWTT) properties in thicker gauge high strength low alloy products, it is necessary to control austenite grain coarsening prior to the onset of thermomechanical processing. This contribution proposes a suite of methods to refine the austenite grain from both theoretical and practical perspective including: increasing cooling rate during casting, liquid core reduction, increasing austenite nucleation sites during the delta ferrite to austenite phase transformation, controlling holding furnace temperature and time to avoid austenite coarsening, and producing new alloy with two phase pinning to arrest grain coarsening. These methodologies can not only refine austenite grain size in the slab center, but also improve the slab homogeneity.

Modeling the flow of polymer solutions requires knowledge at various length and time scales. The macroscopic behavior is described by the overall velocity, pressure and stress. The polymeric contribution to the stress requires knowledge of the evolution of polymer chains. In this work, we use a microscopic model, the finitely extensible nonlinear elastic (FENE) model, to capture the polymer behavior. The benefit of microscopic models is they remain faithful to the polymer dynamics without information loss via averaging. The downside is the computational cost needed to solve the thousands to millions of differential equations describing the microstructure. We thus describe a multiscale flow solver that utilizes GPUs for massively parallel, efficient simulations. We compare and contrast the microscopic model with its macroscopic counterpart under various flow conditions. In particular, significant differences are observed under nonlinear flow conditions, where the polymers become highly stretched and oriented.

Pancreatic cancer (PC) has a poor prognosis and displays resistance to immunotherapy. A better understanding of tumor-derived extracellular vesicles (EVs) effects on immune responses might contribute to improved immunotherapy. EVs derived from Capan-2 and BxPC-3 PC cells isolated by ultracentrifugation were characterized by atomic force microscopy, western blot (WB), nanoparticle tracking analysis and label-free proteomics. Fresh PBMCs from healthy donors were treated with PC- or control-derived heterologous EVs followed by flow cytometry analysis of CD8+ and CD4+ lymphocytes. Proteomics of lymphocytes sorted from EV-treated, or -untreated PBMCs was performed and IFN-γ concentration was measured by ELISA. Notably, most of the proteins identified in Capan-2 and BxPC-3 EVs by proteomic analysis were connected in a single functional network (p=1x10-16) and were involved in “Immune System” (FDR: 1.10x10-24 and 3.69x10-19, respectively). Interestingly, treatment of healthy donor-derived PBMCs with Capan-2 EVs, but not with BxPC-3 EVs or heterologous control EVs induced early activation of CD8+ and CD4+ lymphocytes. Proteomics of lymphocytes sorted from EV-treated PBMCs was consistent with their activation by Capan-2 EVs, indicating IFN-γ among major upstream regulators, as confirmed by ELISA. Proteomic and functional analyses indicate that PC-EVs have pleiotropic effects, and some may activate early immune response, which might be relevant for the development of highly needed immunotherapeutic strategies in this immune-cold tumor.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

There is a confusion in the original design concept for the tensioning of longitudinally connected reinforcement of CRTSII slab ballastless track. In order to clarify the effect of tension value of longitudinal reinforcement on mechanical characteristics of ballastless track, a three dimensional finite element model considering the nonlinear interaction between the track slab and CA mortar of CRTSII slab ballastless track was established. The mechanical characteristics of the track structure under longitudinal tension load and temperature gradient load of the longitudinal joint were calculated. A method of applying pre-stress to post-pouring concrete was proposed according to the concept of pre-stress loss of pretensioning pre-stressed concrete, reasonable tensile force value was proposed after the crack width and the reinforcement stress of the ballastless track in the operation stage were checked and calculated according to the concrete design principle. When the tension force is greater than 300 kN, it’s harmful to the bonding between the slab and mortar layer, which is prone to interlayer damage. In order to adding pre-stress to concrete of wide joints to ensure the longitudinal stability of ballastless track and the reinforcement stress and crack width to meet the design requirements. It is suggested that the tension force value should be 230 kN, and the temperature difference between reinforcement and concrete should be 30 °C before the initial curdle of wide joint concrete.

The study of the concentrations and effects of fine particulate matter in urban areas have been of great interest to researchers in recent times. This is due to the acknowledgment of the far-reaching impacts of fine particulate matter on public health. Remote sensing data have been used to monitor the trend of concentrations of particulate matter by deriving aerosol optical depth (AOD) from satellite images. The Center for International Earth Science Information Network (CIESIN) has released the second version of its global PM_2.5 data with improvement in spatial resolution. This paper revisits the study of spatial and temporal variations in particulate matter in Saudi Arabia by exploring the cluster analysis of the new data. Cluster analysis of the PM_2.5 values of Saudi cities is performed by using Anselin local Moran’s I statistic. Also, the analysis is carried out at the regional level by using self-organizing map (SOM). The results show an increasing trend in the concentrations of particulate matter in Saudi Arabia, especially in some selected urban areas. The eastern and south-western parts of the Kingdom have significantly clustering high values. Some of the PM2.5 values have passed the threshold indicated by the World Health Organization (WHO) standard and targets posing health risks to Saudi urban population.

Shear thickening fluids (STF) are a class of fluids whose viscosity significantly rises under external loads. The research on these fluids has been advancing in recent years regarding prospective practical applications, including developing impact-absorbing composites. Following the green agendas governments and legislators advocate, this study investigates the combination of STF and other sustainable materials. Cork is a naturally occurring cellular material with a negative carbon footprint and superior energy absorption properties. With varying concentrations of STF material, cork agglomerates were formed. Notably, the analysed blends are homogeneous, contrasting with previous literary works. A series of experiments were conducted in quasi-static and dynamic conditions to determine the various mechanical responses. STF appears to influence the mechanical behaviour of cork agglomerates by providing softer deceleration rates and dispersing more energy through disaggregation mechanisms.

The purpose of this paper is to show a new approach to unify the theory of general relativity and quantum physics. For this, we rely on thermodynamics, fluid mechanics and the theory of information. We will then see that the Shannon entropy, Boltzmann and Von Neumann can be the source of gravity, which would be a form emerging. For this, we will study at first what is lacking for the unification of general relativity and physics. Secondly, we will explain the concept of entropic gravity by introducing calculations Erik Verlinde. Then we will explain the concept of entropy Boltzmann, Shannon, Von Neumann and the links between them. Then, we will modify Einstein's equations by transforming the tensor of perfect fluid in terms of entropy. Finally, we will link our theory with experience already carried out as part of a link between gravity and quantum theory.

We develop an action principle for producing a single fluid, two-constituent system with dissipation. The two constituents in the model are particles and entropy. The particle flux creation rate is taken to be zero, while the entropy creation rate is non-zero. Building on previous work, it is demonstrated that a new term (the proper time derivative of the matter space ``metric'') is required in the Lagrangian in order to produce terms typically associated with bulk and shear viscosity. Equations of motion, entropy creation rate, and energy-momentum-stress tensor are derived. Using an Onsager approach of identifying thermodynamic ``forces'' and ``fluxes'' a model is produced which delivers the same entropy creation rate as the standard, relativistic Navier-Stokes equations. This result is then contrasted with a model generated in the spirit of the action principle, which takes as its starting point a specific Lagrangian and then produces the equations of motion, entropy creation rate, and energy-momentum-stress tensor. Unlike the equations derived from Onsager reasoning, where the analogs of the bulk and shear viscosity coefficients are prescribed ``externally'', we find that the form of the coefficients in the second example are a direct result of the specified Lagrangian. Furthermore, the coefficients are shown to satisfy evolution equations along the fluid worldline; also a product of the specific Lagrangian.

In this study, nano-diamond (ND) and MoS2 powder are used as additives in a carbonyl iron based magnetorheological fluid (MRF) to improve its tribological performance. MRFs are prepared by dispersing 35 wt.% of CI particles in silicone oil, and adding different proportions (0, 1, 3 or 5 wt.%) of ND and MoS2 additives. Seven kinds of MRFs are made and tested using reciprocating friction and wear tester under different normal loads, and then the friction characteristics are evaluated through analyzing experiment results. The morphology properties of MRFs and contacting surfaces before and after tests are also observed using a scanning electron microscope and analyzed by energy-dispersive X-ray spectroscopy. The results show that the appropriate weight percentage of MoS2 additives may decrease friction coefficient and wear zone. It is also demonstrated from the detailed analyses of worn surfaces that the wear mechanism is influenced not only by additives but also by applied normal load and magnetic field strength.

There is a growing trend among consumers to seek out natural foods and products with natural ingredients. This shift in consumer preferences had a direct impact on both food and pharmaceutical industries, leading to a focus of scientific research and commercial efforts to meet these new demands. The aim of this work is to review recent available scientific data on foods of interest, such as artichoke, gooseberry, and polygonoideae plants, as well as olive oil and red raspberries. Interestingly, the urgency of solutions to the climate change emergency has brought new attention to by-products of grapevine bunch stem and cane, which have been found to contain bioactive compounds with potential health benefits. There is a pressing need for a faster process of translating scientific knowledge from the laboratory to real-world applications, especially in the face of the increasing societal burden associated to non-communicable diseases (NCDs), environmental crises, the post-pandemic world, and ongoing violent conflicts around the world.

Background: The modified Duke index derived from coronary computed tomography angiography (CCTA) was designed to predict cardiovascular outcomes based on the severity of coronary ste-nosis. However, it does not take into consideration the presence or severity of peri-coronary in-flammation. The peri-coronary fat attenuation index (FAI) is a novel imaging marker determined by CCTA which reflects the degree of inflammation in the coronary tree in patients with coronary artery disease. Purpose: To assess the association between the modified Duke index assessed by CCTA, cardiovascular risk factors and peri-coronary inflammation in the coronary arteries of pa-tients with coronary artery disease. Methods: One hundred seventy-two patients who underwent CCTA for typical angina were assigned into two groups based on the modified Duke index: group 1 – patients with low index ≤ 3 (n=107) and group 2 – patients with high index > 3 (n=65). Demo-graphic, clinical and CCTA data were collected for all patients, and FAI analysis of coronary in-flammation was performed. Results: Patients with increased values of the modified Duke index were significantly older compared to those with a low index (61.83 ± 9.89 vs. 64.78 ± 8.9; p = 0.002). No differences were found between the two groups in terms of gender distribution, hypertension, hypercholesterolemia or smoking history (all p > 0.5). The FAI score was significantly higher in patients from group 2, who presented a significantly higher score of inflammation compared to the patients in group 1, especially at the level of the right coronary artery (FAI score 20.85 ± 15.80 vs. 14.61 ± 16.66; p = 0.01 for the right coronary artery, 13.85 ± 8.04 vs. 10.91 ± 6.5; p = 0.01 for the circumflex artery, and 13.26 ±10.18 vs. 11.37 ± 8.84; p = 0.2 for the left anterior descending artery). CaRi-Heart® analysis identified a significantly higher risk of future events among patients with a high modified Duke index (34.84 % ± 25.86 % versus 16.87 % ± 15.80 %; p

Many studies on magnetorheological fluid (MRF) have been carried out over last three decades several salient advantages such as fast phase change, easy control of the yield stress and so forth. Especially, several review articles of MRF technology have been reported for last two decades summarizing the development of MRFs and their applications. As specific examples, the review articles including the optimization of the particles and carrier liquid to achieve minimum off-state viscosity and maximum yield stress at on-state, the formulation of many constitutive models in-cluding Casson model and Herschel-Bulkley (H-B) model, the sedimentation enhancement using additives and nanosized particles, many types of dampers for automotive suspension and civil structures, medical and rehabilitation devices, MRF polishing technology, the methods of mag-netic circuit design, and the synthesis of various controllers have been published. More recently, the effect of the temperature and thermal conductivity on the properties of MRFs and application systems are actively being investigated by several works. However, there is no review article on this issue so far despite of that the thermal problem is one of crucial factors to be seriously con-sidered for the development of advanced MRFs and commercial products of application systems. In this work, studies on the thermal conductivity and temperature in MRFs themselves and tem-perature-dependent application systems are reviewed, respectively, and principal results are summarized emphasizing on the followings: how to reduce the temperature effect on the field-dependent properties of MRFs and how to design application system to minimize the thermal effect. It is noted here that the review summary is organized in a chronological format using tables.

The objective of this study was to carry out the extraction and characterization of chitin and chitosan from the exoskeletons of the Farfantepenaeus californiensis species of shrimp, as well as its application in the formulation of polymeric films plasticized with glycerol used in the process of food packaging. The characterization of the extracted polymer was made by Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), and physicochemical analysis of chitin and chitosan, resulting in a theoretical performance of 29.33% and 16.46%, respectively. In terms of quality, it was determined that the extracted chitosan had a molecular weight of 1.10 x105 g/mol and a deacetylation degree of 80.23%, which classifies it as a low-molecular weight chitosan, suitable for food packaging. It was shown that the extracted chitosan is fit for the production of the films by using the casting method, presenting a tension resistance of 1 MPa. The Antibacterial analysis was carried out using Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), bacterial models commonly found in food. The results showed an effective inhibition capability of the polymeric materials. Overall, the results for both chitosan and the films indicate a high potential for application in the food packaging sector.

Biomass materials have received attention for energy storagebecaused of the advantage of low-cost, easy-to-prepare, and eco-friendliness. Three-dimensional carbon materialswith abundant pore structure gradually becomeresearch hotspot in high-performance energy storage. In this study, an easy-to-prepare, green, light and elastic activated carbon was present using the biomass Juncus effusus (JCE) via high-temperature pyrolysis, followed by activation in air. Compared with previously reported bio-carbons, the proposed air-activated bio-carbon contributes in the fabrication of pores to preserve the interconnected, reticular and tubular structure. Moreover, the interconnected porous material also inherits the excellent tenacity of the original JCE such as the material can be bended to below 90^o under an external force while maintaining structural integrity. The activated porous carbon material exhibits an enhanced electric double-layer capacitance (~210 F g^-1 at 1 A g^-1), with capacitance retention of ~78.62% at 10 A g^-1. The interconnected porous carbon microtubes electrode as a double-layer symmetric capacitor exhibits considerable capacitance retention (84%) after 2000 cycles at 1 A g^-1. The improved energy storage performance was proposed to be attributed to the shortened ionic diffusion distance and sufficient contact between the interface of the carbon electrode and electrolyte, which is resulted from the elastic, undamaged structure and types of pores. These results demonstrated that as-preparedcarbon materials have potentional application in symmetric capacitors.

Magnetorheological fluids (MRFs) are smart materials consisting of micro-scale magnetizable particles suspended in a carrier fluid. The rheological properties of a MRF can be changed from a fluid-state to a solid-state upon the application of an external magnetic field. This study reports the development of a particle-level simulation code for magnetic solid spheres moving through an incompressible Newtonian carrier fluid. The numerical algorithm is implemented within an open-source finite-volume solver coupled with an immersed boundary method (FVM-IBM) to perform fully-resolved simulations. The particulate phase of the MRF is modeled using the discrete element method (DEM). The resultant force acting on the particles due to the external magnetic field (i.e., magnetostatic polarization force) is computed based on the Clausius-Mossotti relationship. The fixed and mutual dipole magnetic models are then used to account for the magnetic (MAG) interactions between particles. Several benchmark flows were simulated using the newly-developed FVM-IBM-DEM-MAG algorithm to assess the accuracy and robustness of the calculations. First, the sedimentation of two spheres in a rectangular duct containing a Newtonian fluid is computed without the presence of an external magnetic field, mimicking the so-called drafting-kissing-tumbling (DKT) phenomenon. The numerical results obtained for the DKT case study are verified against published data from the scientific literature. Second, we activate both the magnetostatic polarization and the dipole-dipole forces and resultant torques between the spheres for the DKT case study. Next, we study the robustness of the FVM-IBM-DEM-MAG solver by computing multi-particle chaining (i.e., particle assembly) in a two-dimensional (2D) domain for area volume fractions of 20% (260 particles) and 30% (390 particles) under vertical and horizontal magnetic fields. Finally, the fourth computational experiment describes the multi-particle chaining in a three-dimensional (3D) domain allowing to study fully-resolved MRF simulations of 580 magnetic particles under vertical and horizontal magnetic fields.

This study aimed to investigate the potential of Cord Blood Stem Cell-derived exosome vesicles (CBSC-EVs) in regulating cancer growth and preventing cellular damage. The study aimed to examine the effects of CBSC-EVs on CHL1 cancer cells and healthy fibroblasts. The study results reveal that CBSC-EVs have an anti-cancer/antioxidant effect on CHL1 cancer cells without inducing any toxic effects on healthy lymphocytes. Further analysis of CBSC-EVs revealed the presence of seven miRNAs (noncoding RNA molecules), including three from the Let 7 family, two from the Let 5 family, and two novel miRNAs. The function of the novel miRNAs was the main focus of the study. To assess the efficacy of CBSC-EVs, CHL1 cells (a type of malignant melanoma cell line) and human fibroblasts were grouped into different treatments. One group of those cell lines were treated with CBSC-EVs, and in the second group, the cells were transfected with either miRNA inhibitor Novel 1 (miRNA IN1) plus CBSC-EVs or miRNA inhibitor Novel 2 (miRNA IN2) and CBSC-EVs to knock down those novel miRNAs in the CBSC-EVs. Therefore, by comparing these groups, the function of novel miRNAs is more understandable. In this study, the Comet assay was employed to evaluate cancer cells' DNA damage and CCK8 to measure cell viability. The findings revealed that CBSC-EVs caused an increase in DNA damage in CHL1 cells compared to cells without treatment (p

The stromal vascular cell fraction (SVF) of visceral and subcutaneous adipose tissue (VAT and SAT) has increasingly come into focus in stem cell research, since these compartments represent a rich source of multipotent adipose-derived stem cells (ASCs). ASCs exhibit a self- renewal potential and differentiation capacity. Our aim was to study the different expression of embryonic stem cell markers NANOG, SOX2 and OCT3/4 and to evaluate if there exists a hierarchal role in this network in ASCs derived from both SAT and VAT. ASCs were isolated from SAT and VAT biopsies of 72 consenting patients (23 men, 47 women; age 45 ± 10; BMI between 25 and 30 range) undergoing elective open-abdominal surgery. Sphere-forming capability was evaluated by plating cells in low adhesion plastic. Stem cell markers CD90 and CD105 were analyzed by flow cytometry and stem cell transcription factors NANOG, SOX2 and OCT3/4 were detected by immunoblotting and Real-Time PCR. NANOG, SOX2 and OCT3/4 interplay was explored by gene silencing. ASCs from VAT and SAT confirmed their mesenchymal stem cell (MSC) phenotype expressing the specific MSC markers CD90, CD105, NANOG, SOX2 and OCT3/4. NANOG silencing induced a significant OCT 3/4 (70% ± 0.05) and SOX2 (75% ± 0.03) down-regulation whereas SOX2 silencing did not affect NANOG gene expression. Adipose tissue is an important source of MSC, and siRNA experiments endorse a hierarchical role of NANOG in the complex transcription network that regulates pluripotency and plasticity.

Economic expedience of waste heat recovery systems (WHRS), especially for low temperature difference applications, is often questionable due to high capital investments and long pay-back periods. By its simple design isobaric expansion (IE) machines could provide a viable pathway to utilize otherwise unprofitable waste heat streams for power generation and particularly for pumping liquids and compression of gases. Different engine configurations are presented and discussed. A new method of modelling and calculation of the IE process and efficiency is used on IE cycles with various pure and mixtures as a working fluid. Some interesting cases are presented. It is shown in this paper, that the simplest non-regenerative IE engines are efficient at low temperature differences between a heat source and heat sink. Efficiency of non-regenerative IE process with pure working fluid can be very high approaching Carnot efficiency at low pressure and heat source/heat sink temperature differences. Regeneration permits to increase efficiency of the IE-cycle to some extent. Application of mixed working fluids in combination with regeneration permits to significantly increase the range of high efficiencies to much larger temperature and pressure differences.

Novel model of biodegradable PHA copolymer films preparation was applied to evaluate biodegradability of various PHA copolymers and discuss its biomedical applicability. In this study, we illustrate the potential biomaterial degradation rate affectability by manipulation of monomer composition via controlling biosynthetic strategies. Within the experimental investigation, we have prepared two different copolymers of 3-hydroxybutyrate and 4-hydroxybutyrate – P(3HB-co-36 mol.% 4HB) and P(3HB-co-66 mol.% 4HB), by cultivating thermophilic bacterial strain Aneurinibacillus sp. H1 and further investigated its degradability in simulated body fluids (SBFs). Both copolymers revealed faster weight reduction in synthetic gastric juice (SGJ) and artificial colonic fluid (ACF) than simple homopolymer P3HB. In addition, degradation mechanisms differed across tested polymers, according to SEM micrographs. While incubated in SGJ, samples were fragmented due to fast hydrolysis sourcing from substantially low pH, which suggest abiotic degradation as the major degradation mechanism. On the contrary, ACF incubation indicated obvious enzymatic hydrolysis. Further, no cytotoxicity of the waste fluids was observed on CaCO-2 cell line. Based on these results in combination with high production flexibility, we suggest P(3HB-co-4HB) copolymers produced by Aneurinibacillus sp. H1 as very auspicious polymers for intestinal in vivo treatments.

Solid particles immersed in a fluid can be found in many engineering, environmental or medical fields. Applications are suspensions, sedimentation processes or procedural processes in the production of medication, food or construction materials. While homogenized behavior of these applications is well understood, contributions in the field of pore-scale fully resolved numerical simulations with non-spherical particles are rare. Using Smoothed Particle Hydrodynamics (SPH) as a simulation framework, we therefore present a modelling approach for Direct Numerical Simulations (DNS) of single-phase fluid containing non-spherically formed solid aggregates. Notable and discussed model specifications are the surface-coupled fluid-solid interaction forces as well as the contact forces between solid aggregates. The focus of this contribution is the numerical modelling approach and its implementation in SPH. Since SPH presents a fully resolved approach, the construction of arbitrary shaped particles is conveniently realizable. After validating our model for single non-spherical particles, we therefore investigate the motion of solid bodies in a Newtonian fluid and their interaction with the surrounding fluid by analyzing velocity fields of shear flow with respect to hydromechanical and contact forces. Results show a dependency of the motion and interaction of solid particles on their form and orientation. While spherical particles move to the centerline region, ellipsoidal particles move and rotate due to vortexes formation in the fluid flow in between.

In this work, we propose a method to measure planar temperature fields of fluids flow. We used a focusing schlieren technique together with a calibration procedure to fulfill such purpose. The focusing schlieren technique uses an off-axis circular illumination to reduce the depth of focus of the optical system. The calibration procedure is based on the relation of the intensity level of each pixel of a focused schlieren image to the corresponding cutoff grid position measured at the exit focal plane of the schlieren lens. The method is applied to measure planar temperature fields of the hot air issuing from a 10 mm diameter nozzle of a commercial Hot Air Gun Soldering Station Welding. Our tests are carried out at different temperature values and different planes along the radial position of the nozzle of the Hot Air Gun Soldering Station Welding. The temperature values obtained experimentally are in agreed with those obtained with a thermocouple.

Familial Mediterranean fever (FMF) is a systemic autoinflammatory disorder caused by inherited mutations in the MEFV (Mediterranean FeVer) gene located on chromosome 16 (16p13.3) and coding pyrin protein. Despite the existing data on MEFV mutations, the exact mechanism of their effect on the development of pathological processes leading to autoinflammation observed in FMF, remains unclear. Induced pluripotent stem cells (iPSCs) are considered an important tool for studying the molecular genetic mechanisms of various diseases due to their ability to differentiate into any cell type, including macrophages, which contribute to the development of FMF. In this study, we developed iPSCs of an Armenian patient with FMF having M694V, p.(Met694Val) (c.2080A>G, rs61752717) pathogenic mutation in exon 10 of the MEFV gene. As a result of direct differentiation, macrophages expressing CD14 and CD45 surface markers were obtained. In addition, we found that the morphology of patient macrophages derived from iPSCs with MEFV mutation was significantly different from that of differentiated from iPSCs of a healthy donor carrying wild-type MEFV gene.

Cranberries are rich in bioactive constituents reported to influence a variety of health benefits, ranging from improved immune function and decreased infections to reduced cardiovascular disease and more recently cancer inhibition. A review of cranberry research targeting cancer revealed positive effects of cranberries or cranberry derived constituents against 17 different cancers utilizing a variety of in vitro techniques; whereas, in vivo studies supported the inhibitory action of cranberries toward cancers of the esophagus, stomach, colon, bladder, prostate, glioblastoma and lymphoma. Mechanisms of cranberry-linked cancer inhibition include cellular death induction via apoptosis, necrosis and autophagy; reduction of cellular proliferation; alterations in reactive oxygen species; and modification of cytokine and signal transduction pathways. Given the emerging positive preclinical effects of cranberries, future clinical directions targeting cancer or premalignancy will be considered

Rotary drilling for oil and natural gas uses drilling fluid for lubrication of the bit, to seal off unstable shale layers, and floating out rock cuttings. Drilling fluid is a water-clay chemical mixture. Produced water is a water-sand chemical mixture. Land farming is a common disposal technique of drilling fluid and produced water. In the land farming process, amendments of fluid are repeatedly applied to the soil surface. Plant growth and soil chemical properties may be altered by additions of drilling fluid, because of alkalinity, salinity, trace elements, and petroleum residue contained in waste. The objective of this study was to determine the change in soil pH, electrical conductivity (EC), total nitrogen and carbon, and extractable nutrient levels following the land application of drilling fluid and produced water. The study was a comparison of three plots with similar soil properties and conditions. The three study plots had various levels of drilling fluid and produced water applications. The data show a major difference from field-to-field for EC, Na, and Cl levels. The EC and salt levels increased with additional applications of drilling fluid and produced water. The percent total nitrogen values and plant available P levels were very low in all fields. High EC and salt values, coupled with low N and P levels, would be detrimental to plant growth and development. To successfully vegetate this land-farm site, application of N and P fertilizer would be required. This study will help to give a better understanding of practical ways to land-farm drilling fluid and produced water in a fashion that both minimizes environmental issues and is economically feasible. Salinity changes to soil were expected to be high; there are excessive amounts of sodium and chloride in spent drilling fluid and produced water.

Exposure to vaccine lipid nanoparticles, mRNA, adenoviral DNA, and or Spike protein from one of the approved Covid-19 vaccines, or through secondary exposure, as through blood transfusion, is a potential source of harm. Blood reactions are an acknowledged side-effect of Covid-19 vaccination, not limited to hemolysis, paroxysmal nocturnal hemoglobinuria, chronic cold agglutinin disease, immune thrombocytopenia, haemophagocytosis, hemophagocytic lymphohistiocytosis, and many other blood related conditions. The observation of adverse events has motivated investigation into the cardiovascular mechanisms of harm by Covid-19 vaccines, and the biodistribution of vaccine contents. Biodistribution may not be limited to the body of the vaccine recipient, as a growing body of evidence demonstrates the possibility of secondary exposure to vaccine particles. These can be via bodily fluids and include the following routes of exposure: blood transfusion, organ transplantation, breastfeeding, and possibly other means. As covid-19 vaccines are associated with an increased risk of stroke, the persistence of vaccine artifacts in the blood presents a possible threat to a recipient of a blood donation from a vaccinated donor who suffered from vaccine induced thrombosis or thrombocytopenia. (VITT) We assess the feasibility and significance of these risks through an overview of the case report literature of blood disorders in vaccinated individuals, pharmacovigilance reports from the US Vaccine Adverse Events Reporting System (VAERS) and a meta-analysis of the available literature on organ transplants from vaccinated organ donors. Our analysis establishes biological mechanistic plausibility, a coherent safety signal in pharmacovigilance databases for secondary vaccine contents exposure (for the cases of blood transfusion and breastfeeding) and also an elevated level of adverse events in organ transplants from VITT-deceased donors, echoing increases in organ transplantation related complications seen in national statistics for some countries. Secondary exposure to vaccine artifacts is a potential explanation for some of the cases put forth, and requires a deeper investigation.

Digital medicine based on the integration of all medical data of a particular patient, has become a reality today, thanks to information technology. Traditional medical examinations can be supple-mented by assessment results of the oxidative-anti-oxidative (OAO) status of the body [1]. Elec-trochemical sensors are able to not only determine the integral indicators of the OAO system of the body, but also to depict details of the processes occurring in the system. The main obstacle to the widespread use of electrochemical sensors in medical diagnostics is the extremely small amount of the received information in comparison with tens of thousands of known human dis-eases. The problem can be eliminated only by rethinking the purpose of electrochemical measure-ment within the framework of thermodynamics of information processes and information theory. In the information paradigm of electrochemical analysis of biological fluids, a sample is considered as an electrochemical message created by a sensor. The purpose of electrochemical measurement is to obtain information in a volume sufficient to identify the sample composition within the range of possible concentrations of its components. The fundamentals of the thermodynamics of infor-mation processes are considered and conclusions that are of practical importance for the devel-opment of electrochemical sensors and analyzers are derived. It is shown that potentiostatic con-trol of the sensor is physically impacted by the electromechanical instability of the electrical double layer, which is the main source of sensor signal noise. Estimates are of a minimum amount of an-alytical signal information required for identification of a sample of a known composition, such as a biological fluid, are provided. Examples of highly informative analytical signals for flowing and stationary samples are presented. Problems related to the visualization of such signals are noted.

We present a numerical study in which large-scale bulk simulations of self-assembled DNA constructs have been carried out with a realistic coarse-grained model. The investigation aims at obtaining a precise, albeit numerically demanding, estimate of the free energy for such systems. We then, in turn, use these accurate results to validate a recently proposed theoretical approach that builds on a liquid-state theory, the Wertheim theory, to compute the phase diagram of all-DNA fluids. This hybrid theoretical/numerical approach, based on the lowest order virial expansion and a nearest-neighbor DNA model, can provide, in an undemanding way, a thermodynamic description of DNA associating fluids that is in semi-quantitative agreement with experiments. We show that the predictions of such scheme are as accurate as the ones obtained with more sophisticated methods. We also demonstrate the flexibility of the approach by incorporating non-trivial additional contributions that go beyond the nearest-neighbor model to compute the DNA hybridization free energy.

This study's main target was to analyze and design rectangular edges supported two ways solid slabs by using ES EN 1992-1-1:2015. Slab design is often carried out either manually or with the use of design and analytic software. The researcher sees that some software cannot accept some countries' standard codes. For example, currently in Ethiopia analysis and design of two-way solid slab is done using readily available Excel sheet template. But working with this might have many problems, firstly the structure that is already analyzed by SAP or SAFE or any other international software application that uses international codes but which cannot design structure using ES EN 1992; for instant euro codes and designed by excel sheet can create failure and uneconomical analysis and design result. In this paper, the slab is designed and analyzed based on the chosen concrete grade, chosen reinforcement bar diameter, chosen steel grade for design and analysis of slabs calculations like load, moment, shear, and deflection checking using the moment coefficient method for analysis and design and Microsoft Visual Basic 2010 for coding. All input values are given by the International Standard units and are also used to represent output values. Using manual calculations delays time and mostly the result is not correct. But using this Computer program can increase computation accuracy and save time. The procedure the researcher followed is, first the manual calculation has been done and then SADSE2021 has been done. The result is that both are 99.9% identical, and the disadvantage of this method is that it cannot be used to determine the detailed drawing.

This cross-sectional study evaluated the validity of three alternative methods compared to the gold standard 24-h urine collection for estimating dietary sodium intake, a modifiable risk factor for hypertension, among middle-aged and older adults with elevated blood pressure. These included spot urine collection (using Kawasaki, Tanaka, and INTERSALT equations), 24-h dietary recall, and food frequency questionnaire responses, compared against 24-h urine collection in a subset of 65 participants (aged 50–75 years, 58.5 % women, 61.6 % hypertensive) from the DePEC-Nutrition trial. The validity of the methods was assessed using bias, Spearman correlation coefficient (SCC), intraclass correlation coefficient (ICC), and Bland-Altman analysis. Among the alternative methods, spot urine collection using the Kawasaki equation showed the strongest correlation (SCC 0.238; ICC 0.119, 95 % CI -0.079 to 0.323) but it exhibited a significant bias (1414 mg/day, p-value < 0.001) relative to 24-h urine collection. Conversely, dietary surveys had a smaller bias but wider limits of agreement. These findings underscore the complexities of accurately estimating dietary sodium intake using spot urine collection or dietary surveys in this specific population, suggesting that a combination or refinement of existing methodologies might improve accuracy. Further research with larger samples is necessary to develop more reliable methods for assessing sodium intake in this high-risk group.

Background: We assess locoregional drug targeting effectiveness of intraoperative (IO) cryoprobe-assisted injection of blue dye (BD) and cytotoxic-tracer mixture (TTM), in VX2 tumor model, and its translational value to cryo-assisted breast tumor surgery with BD alone. Methods: Under computed tomography (CT) guidance, we injected two ml TTM in five aliquots in the margin of 16 frozen or normothermic VX2 tumors. We evaluated the IO and post-operative drug targeting and therapeutic efficacy in tumor-host interface (T-HI) by CT, gross examination, and histopathology. In twenty-six T1 to T4 primary breast cancer (BRCA) we performed ultrasound-guided (US) cryoprobe-assisted tumor freezing, BD guided lymphatic mapping, and surgery. We evaluated, IO and in freshly resected specimen, BD distribution pattern in T-HI, lymph node(s), breast parenchyma, and resection cavity. Results: Fluids-impervious frozen VX2 or breast tumor transported drug(s) an arc-like pattern at T-HI regardless of freeze dose, number of freeze-thaw cycles, drug dose fractionation, tumor characteristics or dimensions. During melting, TTM spread within fifty percent VX2 tumor mirrored that of T-HI; it was massive in normothermia. In VX2 twenty percent focal margin necrosis at pathology coincided with CT gap; in both studies, BD dose-staining spread in T-HI and tumor was linear. Eighty-four patients had one to twelve stained axillary lymph nodes; sixty-nine percent and all respectively, had another quadrant and resection cavity stained. Conclusion: Intraoperative freezing-assisted drug delivery and targeting techniques during cryoablation of VX2 tumor translate successfully to locoregional BD targeting, lymphatic mapping during cryo-assisted surgery of breast cancer.

The recent green manufacturing demands have boosted the development of new biodegradable lubricants to replace petroleum-based lubricants. In this regard, water-based lubricants have been at the forefront of recent research for a wide range of industrial applications, including metalworking fluids (MWFs). In this work, we present an experimental investigation on the performance of novel green MWFs based on aqueous nopal mucilage solutions. For this, fully biodegradable solutions with different mucilage concentrations were evaluated in terms of rheological, tribological, thermal stability and turning (minimum quantity lubrication) performance, and compared to a commercial semisynthetic oil-based MWF (Cimstar 60). Mucilage solutions exhibited viscoelastic shear-thinning behavior, which was enhanced along with mucilage concentration. The solution with the highest mucilage content studied resulted in the lowest wear, friction and temperature in comparison to the other solutions and neat water in extreme pressure four-ball tests, and a similar level of lubricity as compared to the commercial MWF in cutting tests. This performance is associated to the enhanced viscosity and elasticity of the solution, as well as to the contents of lipids with fatty acids in the mucilage. Overall, the present results reveal the relevance of the viscoelastic behavior of the lubricant, elasticity in particular, in lubrication processes, and points to nopal mucilage as an effective green additive to produce innocuous MWFs.

The Particle-In-Cell (PIC) method has been developed in order to investigate microscopic phenomena, and with the advances of computing power, newly developed codes have been used for several fields such as astrophysical, magnetospheric, and solar plasmas. PIC applications have grown extensively with large computing powers available on supercomputers such as Pleiades and Blue Waters in the US. For astrophysical plasma research PIC methods have been utilized for several topics such as reconnection, pulsar dynamics, non-relativistic shocks, relativistic shocks, relativistic jets, etc. PIC simulations of relativistic jets have been reviewed with the emphasis on the physics involved in the simulations. This review summarizes PIC simulations, starting with the Weibel instability in slab models of jets, and then focuses on global jet evolution in helical magnetic field geometry. In particular we address kinetic Kelvin-Helmholtz instabilities and mushroom instabilities.

Multivariate statistical approaches (MSA), such as principal components analysis and multidimensional scaling, seek to uncover meaningful patterns within datasets by considering multiple response variables in a concerted fashion. Although these techniques are readily used by ecologists to visualize and explain differences between study sites, they could theoretically be employed to differentiate organisms within an experimental framework while simultaneously identifying response variables that drive documented experimental differences. Therefore, MSA were used herein to attempt to understand the response of the common, Indo-Pacific reef coral Seriatopora hystrix to temperature changes using data from laboratory-based temperature challenge studies performed in Southern Taiwan. Gene expression and physiological data partitioned experimental specimens by time of sampling, treatment temperature, and site of origin upon employing MSA, signifying that S. hystrix and its dinoflagellate endosymbionts display physiological and molecular signatures that are characteristic of sampling time, site of colony origin, and/or temperature regime. These findings promote the utility of MSA for documenting biologically meaningful shifts in the physiological and/or sub-cellular response of marine invertebrates exposed to environmental change.

Cell-penetrating peptides (CPPs), a group of small peptides capable of promoting the transport of molecular cargo across the plasma membrane, have become important tools in promoting the cellular uptake of exogenously delivered macromolecules. GV1001, a peptide derived from a reverse-transcriptase subunit of telomerase (hTERT) and developed as a vaccine against various cancers, reportedly has unexpected CPP properties. Unlike typical CPPs, such as the HIV-1 TAT peptide, GV1001 enabled the cytosolic delivery of macromolecules such as proteins, DNA and siRNA via extracellular heat shock protein 90 (eHSP90) and 70 (eHSP70) complexes. The eHSP-GV1001 interaction may have biological effects in addition to its cytosolic delivery function. GV1001 was originally designed as a MHC class II-binding cancer epitope, but its CPP properties may contribute to its strong anti-cancer immune response relative to other telomerase peptide-based vaccines. Cell signaling via eHSP-GV1001 binding may lead to unexpected biological effects, such as direct anticancer or antiviral effects. In this review, we focus on the CPP effects of GV1001 bound to eHSP90 and ehsp70.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

In this effort we propose a data-driven learning framework for reduced order modeling of fluid dynamics. Designing accurate and efficient reduced order models for nonlinear fluid dynamic problems is challenging for many practical engineering applications. Classical projection-based model reduction methods generate reduced systems by projecting full-order differential operators into low-dimensional subspaces. However, these techniques usually lead to severe instabilities in the presence of highly nonlinear dynamics, which dramatically deteriorates the accuracy of the reduced-order models. In contrast, our new framework exploits linear multistep networks, based on implicit Adams-Moulton schemes, to construct the reduced system. The advantage is that the method optimally approximates the full order model in the low-dimensional space with a given supervised learning task. Moreover, our approach is non-intrusive, such that it can be applied to other complex nonlinear dynamical systems with sophisticated legacy codes. We demonstrate the performance of our method through the numerical simulation of a two-dimensional flow past a circular cylinder with Reynolds number Re = 100. The results reveal that the new data-driven model is significantly more accurate than standard projection-based approaches

The first diastereoselective synthesis of (–)-1-epi-lentiginosine stars from a common chiral trans-epoxyamide derived from 2-pyridincarbaldehyde is reported. This methodology involves a sequential oxirane ring opening and intramolecular 5-exo-tet cyclization of tosylate tras-epoxyalcohol to afford a diastereomeric mixture of indolizinium salts in a one-pot fashion, followed by regio- and diastereospecific pyridinium ring reduction.

We revise the definition of graph operations in [WDK2018] and adapt correspondingly the construction of graph term algebras. As a first contribution to a prospective research field Universal Graph Algebra, we generalize some basic concepts and results from algebras to graph algebras. To tackle this generalization task, we revise and reformulate traditional set-theoretic definitions, constructions and proofs in Universal Algebra by means of more category-theoretic concepts and constructions. Especially, we generalize the concept generated subalgebra and prove that all monomorphic homomorphisms between graph algebras are regular. Derived graph operations are the other main topic. After an in depth analysis of terms as representations of derived operations in traditional algebras, we identify three basic mechanisms to construct new graph operations out of given ones: parallel composition, instantiation, and sequential composition. As a counterpart of terms, we introduce graph operation expressions with a structure as close as possible to the structure of terms. We show that the three mechanisms allow us to construct for any graph operation expression a corresponding derived graph operation in any graph algebra.

The Shimensi super-large tungsten polymetallic deposit is located in Late Jurassic- Early Cretaceous Porphyry-Skarn tungsten ore belt in the south Yangtze metallogenic belt. There are 3 types of mineralization: veinlet-disseminated type, thick quartze vein type and hydrothermal crypto-explosive breccia type. Based on geological studies, this paper presents new petrographic, microthermometric, laser Raman spectroscopic and hydrogen and oxygen isotope research of the fluid inclusions from the deposit. The results show that there are five different types of fluid inclusions: liquid-rich inclusions, vapor-rich inclusions, pure liquid inclusions, pure vapor inclusions, and fluid inclusions containing a solid crystal. The homogenization temperatures of the fluid inclusion range from 140℃-270℃, the salinities are 3%-5% NaCleq and the densities of ore-forming fluid range from 0.64 g/cm3 to 0.99 g/cm3. For the analyses of Laser Raman spectroscopic, the ore-forming fluids can be approximated by a Ca2+-Na+-SO42--Cl- fluid system with small amount of CO2, CH4 and N2. Otherwise, the datas of the pressure, pH and Eh show a fluid metallogenic environment of low pressure, weak acid and weak reduction. The values of the homogenization temperature in 3 types of orebodies suggest that the mineralization is characterized by the decrease of the temperature under the condition of the fluid immiscibility. The H-O isotope values are interpreted to indicate that the ore-forming fluids are mainly composed of magmatic water, and also the meteoric water was added with the process of the magma rising.

Magnetorheological (MR) fluid is recognized as one of intelligent materials that is widely used for various kinds of controllable devices since its rheological characteristics can be controlled by an external magnetic field (or input current). However, the density mismatch of the compositions between iron particles and carrier oil leads to inevitable sedimentation. Therefore, many works on the sedimentation problem of MR fluids have been carried out to improve the sedimentation stability using appropriate additives, surfactants, nanoparticles, particle coating as well as using several carrier oils with different densities. However, a study on the effect of the current magnitudes and profiles on the sedimentation is considerably rare. This study experimentally investigates the sedimentation behaviors due to the different current magnitudes and different profiles such as square and sine wave. It is shown that average sedimentation rate is 98.61% by applying 1 A of the square wave, while it is 97.83% under the sine type of the current. It is also identified that the higher intensity of the applied current results in stronger electromagnetic which can slow down the sedimentation rate. The results presented in this work are very helpful in designing a controller which provides the input current in terms of the magnitude and profile configuration.

Micro-nanoparticles' characteristics in geothermal fluids can be applied to detect of deep hidden geothermal resources. Observations using a nanoparticle tracking analyzer (NTA) indicated that the karst geothermal water collected in the central area of Shandong Province (Jinan and Zibo) contains many natural micro-nanoparticles with sizes primarily ranging between 100 nm and 5 μm. The micro-nanoparticles’ type, shape, crystal form, and chemical composition in the samples were analyzed using transmission electron microscopy (TEM). TEM images and energy dispersive spectroscopy showed that the micro-nanoparticles in geothermal water samples were mostly amorphous, irregular, or nearly spherical, with rough edges. The micro-nanoparticles were mainly carbonates, sulfates, and chlorine-containing Fe, Ca, Na, and Mg. The characteristics of the particles can reveal the properties of the deep, hot reservoirs and aquifers from where they originate. Therefore, we believe that natural micro-nanoparticles can be essential to detecting and studying deep, hidden geothermal resources, which is a novel approach to exploring deep, hidden geothermal resources.

We hypothesized that rumen fluid with yeast producing cellulase enzyme can occur and also produces a high biomass compared to S. cerevisiae. Therefore, the aim of this study was to screen and isolate yeast from rumen fluids with an experimental design method. We optimized a fermentation medium containing sugarcane molasses as a carbon source and urea as a nitrogen source to measure the efficiency of biomass production and cellulase activity. Two fistulated-crossbred Holstein Friesian steers, averaging 350 ± 20 kg body weight, were used to screen and isolate ruminal yeast. The two experiments were designed. A 12 × 3 × 3 factorial was used in a completely randomized design to determine biomass and carboxymethyl cellulase activity. Factor A was isolated yeasts and S. cerevisiae. Factor B was sugarcane molasses (M) concentration. Factor C was urea (U) concentration. Potential yeast was selected for identified and analyzed as a 4 × 3 factorial use in a completely randomized design including. Factor A was incubation times. Factor B was isolated yeast strains including code H-KKU20 (as P. kudriavzevii-KKU20), I-KKU20 (C. tropicalis-KKU20), and C-KKU20 (as Galactomyces sp.-KKU20). Isolation was under aerobic conditions, resulting in a total of 11 different colonies. We noted two appearances of colonies including, asymmetric colonies of isolated yeast (indicated as A, B, C, E, and J) and ovoid colonies (coded as D, F, G, H, I, and K). The highest biomass was observed in three yeasts including codes H, I, and C-KKU20 when inoculated in 25% molasses with 1% urea (M25+U1) (p <0.01). The highest CMCase activity was observed in yeast code H-KKU20 when inoculated in all media solutions (p <0.01). Ruminal yeasts strains H-KKU20, I-KKU20, and C-KKU20 were selected for their ability to produce biomass and their CMCase enzyme synthesis. Identification of isolates H-KKU20 and I-KKU20 revealed that those isolates belonged to Pichia kudriavzevii-KKU20 and Candida tropicalis-KKU20, while C-KKU20 was identified as Galactomyces sp.-KKU20. Two strains provided maximum cell growth: P. kudriavzevii-KKU20 (9.78 and 10.02 Log cell/ml) and C. tropicalis-KKU20 (9.53 and 9.6 Log cells/ml) at 60 and 72 h of incubation time, respectively. The highest ethanol production was observed in S. cerevisiae: 76.4, 77.8, 78.5, and 78.6 g/L at 36, 48, 60, and 72 h of incubation time, respectively (p <0.01). The P. kudriavzevii-KKU20 yielded the least reducing sugar about 30.6 and 29.8 g/L at 60 and 72 h of incubation time, respectively. It could be concluded that screening and isolating yeast from rumen fluids resulted in 11 different characteristics of yeasts. The first novel yeasts discovered in the rumen fluid of cattle were Pichia kudriavzevii-KKU20, Candida tropicalis-KKU20, and Galactomyces sp.- KKU20. P. kudriavzevii-KKU20 had higher results than the other yeasts in terms of biomass production, cellulase enzyme activity, and cell number.

The high genetic diversity of the tomato and its high micronutrient content make this fruit very interesting from an economic and nutritional point of view. The genetic erosion suffered by this crop, due to breeding objectives based on yield and marketing, makes it necessary to return to the origins in search of the nutritional and organoleptic quality lost in traditional varieties. In this study, the agronomic, physical, organoleptic and nutritional characteristics of eighteen F1 hybrids obtained by crossing fourteen traditional varieties, previously selected for their quality, were studied to select genotypes of superior quality that could be candidates for new. All parameters studied were strongly influenced by genotype, showing a wide range between cultivars. Principal Component Analysis revealed the characteristics of each hybrid that made it stand out from the others. Some hybrids (H3, H4, and H6) stand out because of their high concentration of active compounds, others (H16, H15, H10, H17, H9, and H11) because of agronomic performance and high content of β-carotene, and H5 was the only one to contain chlorophyll in their ripe fruits. Finally, the evaluation index allowed the selection of five hybrids with interesting characteristics, combining good yield performance and high quality

An overview is presented of several diverse branches of work in the area of effectively 2D fluid equilibria which have in common that they are constrained by an infinite number of conservation laws. Broad concepts, and the enormous variety of physical phenomena that can be explored, are highlighted. These span, roughly in order of increasing complexity, Euler flow, nonlinear Rossby waves, 3D axisymmetric flow, shallow water dynamics, and 2D magnetohydrodynamics. The classical field theories describing these systems bear some resemblance to perhaps more familiar fluctuating membrane and continuous spin models, but the fluid physics drives these models into unconventional regimes exhibiting large scale jet and eddy structures. From a dynamical point of view these structures are the end result of various conserved variable forward and inverse cascades. The resulting balance between large scale structure and small scale fluctuations is controlled by the competition between energy and entropy in the system free energy, in turn highly tunable through setting the values of the conserved integrals. Although the statistical mechanical description of such systems is fully self-consistent, with remarkable mathematical structure and diversity of solutions, great care must be taken because the underlying assumptions, especially ergodicity, can be violated or at minimum lead to exceedingly long equilibration times. Generalization of the theory to include weak driving and dissipation (e.g., non-equilibrium statistical mechanics and associated linear response formalism) could provide additional insights, but has yet to be properly explored.

Complex colloidal fluids, depending on particulates’ shapes and packing fractions, may have a wide range of shear thinning and thickening behaviors. A particular interesting way to transition between different types of such behavior is by infusing functional complex particles that can be manufactured using modern techicques such as 3D printing. In this paper, we display 2D molecular dynamics simulations of such fluids with infused star-shaped functional particles, with variable leg length and number of legs, as they are infused in a non-interacting, coarse-grained fluid. We vary the packing fraction (ϕ) of the system, and for each different system we apply shear with various strain rate that turns the fluid into a jammed state and rise the apparent viscosity of fluid. We demonstrate the dependence of viscosity with the particles’ packing fraction. We show the role of shape and design dependence of the functional particles towards the transition to a shear thickening fluid .

Meloidogyne nematodes, commonly known as root-knot nematodes, pose a considerable threat to crop yields, resulting in significant economic losses due to their intricate biology and limited control methods. In line with the European Union's focus on promoting organic farming and soil health to encourage sustainable agricultural practices, this study explores the efficacy of two characterized bacterial communities obtained from compost, namely SynCom1 and SynCom2, against Meloidogyne javanica in tomato plants. Through pot experiments, it is demonstrated that both bacterial communities effectively suppress nematode reproduction and root infections while simultaneously enhancing various growth parameters in tomatoes. These findings underscore the potential of synthetic bacterial communities as promising tools for organic or integrated pest management, thereby supporting sustainable agricultural practices and contributing to improved crop yields.

This review article discusses the involvement of the Brain-Derived Neurotrophic Factor (BDNF) in the control of pain. BDNF, a neurotrophin known for its essential role in neuronal survival and plasticity, has garnered significant attention for its potential implications as a modulator of nociception and pain. This comprehensive review aims to provide insights into the multifaceted interactions between BDNF and pain pathways, encompassing both physiological and pathological pain conditions. I delve into the molecular mechanisms underlying BDNF's involvement in pain processing and discuss potential therapeutic applications of BDNF and its mimetics in managing pain. Furthermore, I highlight recent advancements and challenges in translating BDNF-related research into clinical practice.

One source of kaolinite-rich wastes is from mine tailings and the generation of enormous volumes of mine tailings waste is standard practice in this industry. These volumes of waste are, at present, dumped, provoking significant environmental impact and transforming the environment. The impact of storing coal waste requires the study of eco-innovative solutions for the assessment of waste types. The present investigation has the objective of expanding the knowledge on the behavior of new siliceous-aluminum minerals with pozzolanic activity, of added value in the manufacture of similar cements. Four samples were characterized to determine their chemical, morphological and mineralogical composition. The samples were subjected to different thermal activation conditions for the transformation of an inert waste into a material with cementitious properties. XRD analysis have confirmed the total transformation of kaolinite into metakaolinite. The results have shown that after the activation process, the coal refuse presented good pozzolanic activity, meaning that it may be used as a pozzolanic addition in industrial cements, thereby removing high levels of contaminated waste from the environment. In subsequent investigations, research work will continue with the replication of cements with this pozzolanic addition for use in the manufacture of sleepers and slab track railway system.

The hydrochemical composition of the Upper Jurassic groundwaters in the South German Mo-lasse Basin (SGMB) indicates a heterogeneous and varying hydrogeochemical evolution, which contradicts previous flow model concepts. For this study, the data of 88 Tertiary, Cretaceous and Upper Jurassic groundwater samples were investigated for hydrochemical elements, 2H/18O-H2O isotopes, 87Sr/86Sr ratios as well as δ11B values. In addition, the geochemical composition, 87Sr/86Sr and δ11B values were analysed from depth-oriented Upper Jurassic rock samples to delineate water-rock interactions in the aquifer systems. Slightly elevated 87Sr/86Sr ratios of the carbonates compared to the typical signatures of marine Upper Jurassic carbonates indicate a synsedimentary radiogenic influence due to the erosion of the adjacent Bohemian Massif. However, these values cannot explain the significant higher Sr-isotope fingerprint of the groundwaters in the central SGMB. Different water types occur in the Upper Jurassic aquifer, primarily distinguished by the dominant cations, calcium or sodium with subclasses of the major anions. The calcium-dominated groundwaters occur mainly at the western and northern margins of the SGMB. The sodi-um-dominated ion exchange groundwaters instead dominate in the central and eastern SGMB. With increasing strontium content, the 87Sr/86Sr ratios of the Upper Jurassic groundwater samples either indicate a strontium uptake by carbonate of the host rocks, or a prevailing radiogenic sig-nature. This implies a basic interaction with terrestrial or marine Tertiary sediments. The results illustrate a downward transformational fluid flow systematic via the thick Tertiary sediment cover into the Upper Jurassic carbonate formation in the SGMB, highlighting a new understanding on the evolution of the Upper Jurassic groundwaters and a basin-wide recharge mechanism.

Impact of Nitrogen Foamed Stimulation Fluids Stabilized by Nanoadditives on Reservoir Rocks of Hydrocarbon Deposits

Purpose: The treatment of renal fibrosis caused by long-term obstructive nephropathy is limited. The purpose of this study was to establish a mouse model of renal fibrosis with unilateral ureteral obstruction (UUO) and to treat it with exosomes derived from SIRT6 transfected urine-derived stem cells (USCs), which will determine whether exosomes have the effect of anti-fibrosis Methods: The renal fibrosis model of UUO mice was established by ligating unilateral ureter. USCs were extracted from human urine and transfected with SIRT6 lentivirus plasmid. The SIRT6-USCs-exosomes(SIRT6-USCs-exos) were collected and identified by transmission electron microscope, nanoparticle tracking analysis and western blot. SIRT6-USCs-exos were injected into the tail vein of mice and the renal tissue of mice was stained with HE. The relative gene expressions of α-SMA, E-cadherin and TGF-β1 were analyzed by RT-qPCR. Results: In this study, we successfully constructed the renal fibrosis model of UUO mice and hUSCs with overexpression of SIRT6. The SIRT6-USCs-exos significantly improved the renal fibrosis in UUO mice. The relative mRNA expressions of fibrosis-related genes α-SMA, E-cadherin and TGF-β1 in renal tissue were significantly down-regulated after SIRT6-USCs-exos treatment. Conclusion: Our results indicate that SIRT6-USCs-exos can effectively alleviate renal fibrosis caused by long-term obstructive nephropathy. The findings may be promising for dealing with renal fibrosis.

This study investigates the Hagen–Poiseuille pipe flow of viscoplastic fluids, focusing on analytical predictions of concrete pumping using the shear-stress-dependent parabolic model. Research highlights encompass solving the steady laminar pipe flow for viscoplastic fluids described by the parabolic model, extending analytical studies to a nonlinear rheological model with easily accessible experimental parameters, presenting detailed results for the two-fluid parabolic model, and introducing computational apps implementing theoretical findings. The parabolic model outperforms linear models, such as the Bingham model, in accuracy by accounting for the nonlinearity in the shear stress and shear rate relations. The influence of rheological parameters on these relations is analyzed, and their versatility is demonstrated by a Wolfram Mathematica-based application program. This approach is adaptable for other models with shear stress as the independent variable, offering valuable insights into viscoplastic fluid flows.

Fatigue-related subchondral bone injury of the third metacarpal/ metatarsal (McIII/ MtIII) bone is a common cause of wastage and welfare concern in racehorses. Better understanding of bone health and strength would improve animal welfare and be of benefit for the racing industry. Porosity index (PI) of bone is an indirect measure of osseous pore size and number and is therefore an interesting indicator of bone strength. MRI of compact bone using traditional methods even with short echo times fails to generate enough signal to assess bone architecture as the water protons are tightly bound. Ultrashort echo time (UTE) sequences aim to increase the amount of signal detected in the equine McIII/MtIII condyle. Cadaver specimens were imaged using a novel dual-echo UTE MRI technique and PI was calculated and validated against quantitative CT-derived bone mineral density (BMD). BMD and PI are inversely correlated in the equine distal Mc/ MtIII with a mean r value of -0.29. The r value is significantly different between fore- and hindlimbs. Further work is needed to assess how correlation patterns behave in different areas of the bone and to evaluate PI in horses with and without clinically relevant stress injury.

The pathophysiology of Nonketotic Hyperglycinemia (NKH), a rare neuro-metabolic disorder associated with severe brain malformations and life-threatening neurological manifestations, remains incompletely understood. Therefore, a valid human neuronal model is essential. We aimed to investigate the impact of GLDC gene variants, which cause NKH, on cellular fitness during the differentiation process of human induced pluripotent stem cells (iPSCs) into iPSC-derived astrocytes and to identify sustainable mechanisms capable of overcoming GLDC deficiency. We developed the GLDC27-FiPS4F-1 line and performed metabolomic, mRNA abundance and protein analyses. The study showed that although GLDC27-FiPS4F-1 maintained the parental genetic profile, it underwent a metabolic switch to an altered serine-glycine-one-carbon metabolism with a coordinated cell growth and cell cycle proliferation response. We then differentiated the iPSCs into neural progenitor cells (NPCs) and astrocyte-lineage cells. Analysis showed that GLDC-deficient NPCs had shifted towards a more heterogeneous astrocyte lineage with increased expression of the radial glial markers GFAP and GLAST and the neuronal markers MAP2 and NeuN. In addition, we detected changes in other genes related to serine and glycine metabolism and transport, all consistent with the need to maintain glycine at physiological levels. These findings improve our understanding of the pathology and offer new perspectives for therapeutic options.

This article aims to assess the benefits of floor-slab insulation measures using extruded polystyrene (XPS) and polyisocyanurate (polyiso) insulation materials at various levels of insulation thicknesses for a detached residential building. The EnergyPlus simulation analysis was carried out within the seven energy zones (represented by eight locations) of South Africa in accordance with the South African national code for building energy efficiency (SANS10400-XA). The energy savings and payback periods due to use of the insulation over a lifecycle period of 50 years were assessed. Cape Town (zone 4) behaved differently from other locations and hardly benefitted from the application of floor-slab insulation measures. Generally, polyiso insulation performed better than XPS, for vertical gap insulation. For vertical gap insulation, lower insulation thicknesses required higher insulation depths to maximize energy savings. Similarly, lower insulation thicknesses required higher perimeter insulation widths to maximize energy savings, for the horizontal perimeter insulation method. The locations that benefitted most from vertical gap floor-slab insulation were Pretoria (zone2), Kimberley (zone6), Nelspruit (zone3), Fraserburg (zone7), Welkom (zone1), Mthatha (zone5), Ixopo (zone5H) and Cape Town (zone4) in that order. This order was almost similar with those for the horizontal perimeter floor-slab insulation and horizontal full floor-slab insulation methods.

One objective of this paper is to investigate bifurcation of solutions of Ornstein-Zernike equation in liquid state theory for the gas-liquid coexistence region of simple fluids. The analysis uses a discrete form of the Ornstein-Zernike equation in real space, together with a closure relation which provides nearly self consistent thermodynamic properties of fluids governed by interaction potentials like the Lennard-Jones potential. Accurate asymptotic forms of correlation functions are incorporated in the real space algorithm so as to mitigate the influence of cutoff length used in the discrete approximations. It is found that there is no spinodal on the vapor side on a sub-critical isotherm. But there are fold bifurcation points on the vapor and liquid sides together with a 'no-real-solution-region' in between. This is followed by a region of negative compressibility extending up to the spinodal on the liquid side. The emerging picture is quite similar to that in the case of the hypernetted-chain-closure. It is also found that complex solutions connect the physical solutions that exist outside the 'no-real-solution-region' as well as in region of negative compressibility. The second objective of the paper, in the light of bifurcation scenario, is to evolve an interpretation of the coupling-parameter expansion of correlation functions pertaining to the region of negative compressibility. It is shown that the expansion provides an accurate description of results of the restricted ensembles, implied in mean field theories and simulation methods. Bifurcation of singlet density to inhomogeneous distributions at a spinodal is also established using a simple equation, which uses the direct correlation function. Thus the paper reestablishes the fact that restriction to a homogeneous singlet density is the root cause of all inconsistencies found in the gas-liquid coexistence region.

A practical method is presented to estimate rare earth elements (REE) concentrations in magmatic vapour phase (MVP) in equilibrium with water-saturated granitic melts based on empirical fluid-melt partition coefficients of REE (k_P^REE). The values of k_P^REEcan be calculated from a set of new polynomial equations linking to the chlorine molality (m_Cl^v) of the MVP associated with granitic melts, which are established via a statistical analysis on the existing experimental dataset. These equations may be applied to the entire pressure range (0.1 to 10.0 kb) within the continental crust, suggesting that light REEs behave differently in magmatic fluids, i.e. either being fluid compatible with higher m_Cl^v or fluid incompatible with lower m_Cl^v values. In contrast, heavy REEs are exclusively fluid incompatible and partition favourably into granitic melts. Consequently, magmatic fluids tend to be rich in LREE relative to HREE, leading to REE fractionation during the evolution of magmatic hydrothermal systems. Maximum k_P^REEvalue for each element is predicted and presented in a REE distribution diagram constrained by the threshold of m_Cl^v. REE contents of the granitic melt is approximated by whole-rock analysis, so that REE concentrations in the associated MVP would be estimated from the value of k_P^REE given chemical equilibrium retains. Two examples are provided respectively, to show the use of this method as a REE tracer to fingerprint the source of ore-fluids responsible for the Lake George intrusion-related Au-Sb deposit in New Brunswick (Canada), and for the Bakircay Cu-Au (-Mo) porphyry systems in northern Turkey.

Bone is a dynamic tissue with the capacity of repair and regeneration in specific conditions. Nevertheless, due to the increased incidence of bone disorders, the need of bone grafts has been growing over the past decades and the development of an ideal bone graft with optimal properties remains a clinical challenge. This review addresses the bone properties (morphology, composition and their repair and regeneration capacity) and puts the main focus on the potential strategies for developing bone repair and regeneration materials. It describes the requirements for designing a suitable scaffold material, types of materials (polymers, ceramics and composites) and techniques to obtain the porous structures (additive manufacturing techniques/robocasting or derived from marine skeletons) for bone tissue engineering applications. The main objective of this review is to gather the knowledge on the materials and methods for the production of scaffolds for bone tissue engineering and highlighting the potential of natural porous structures such as marine skeletons as promising alternative bone graft substitute materials without any further mineralogical changes, or after partial or total transformation into calcium phosphate. The suitability of the marine-derived porous bone graft substitutes for the intended applications will be also discussed.

One of the operational challenges for the use of bentonite pellets as a sealing material in the abandonment of offshore fields consists in their disposition inside the well. This study aims to analyze the interaction of fluid media, consisting of saline solutions (NaCl, CaCl2 and KCl) and organic compounds (diesel, glycerin and olefin), with bentonite pellets, aiming its application as displacement fluid in offshore oil well abandonment operations. The physical integrity of the bentonite pellets in contact with the fluids was verified through visual inspections and dispersibility tests. Linear swelling tests were also performed to evaluate the potential for swelling of pellets in deionized water after contact with the fluid media. The results indicated that NaCl, CaCl2 and KCl solutions completely compromise the physical integrity of the pellets, while diesel and olefin showed the best responses regarding the structural preservation. Futhermore, the linear swelling tests showed that, even after the contact with diesel and olefin for 1 hour, bentonite pellets have reached a total swelling in water of 78%, after 24 hours. In this way, diesel and olefin proved to be highly promising alternatives to be used as displacement fluids for bentonite pellets in wells to be abandoned in a submarine environment.

Despite the fact that strong routine separation methodologies can give reliable specificity and validity at usual working pharmaceuticals concentrations, they may fail at very low concentration levels. This poses considerable challenges for researchers inves-tigating product purity and therapeutic drug monitoring. Sensitivity enhancement pro-cedures are thus required to maximize the performance of separation techniques. Large volume injection, solid phase extraction/solid phase enrichment (SPE/SPEn), pre-, post-, and in-column derivatization, as well as the use of sensitive detection devices are the simplest strategies for improving sensitivity of the separation-based analytical techniques. Large volume injection of samples with online SPE/SPEn coupled with separation techniques increased sensitivity and improved detection as well as quantification limits without affecting peak shape and system performance. Although the primary purpose of derivatization is to improve sensitivity and selectivity, greener derivatization is growing in popularity and should be considered in analytical chemistry. In general, two strategies are essential for accomplishing greener derivatization goals. The first is the search for and use of ecologically acceptable derivatizing reagents, solvents, and reaction conditions. The second is miniaturization and automation of analytical methods. This review discusses significant advances in separation-based analytical techniques, specifically enrichment approaches and detector signal improvement for pharmaceutical quantification in various matrices at very low concentration levels. As a result of improved analytical systems setup in drug assays, the possibility of high-throughput analyses was also highlighted.

We analyze the thermal convection thresholds and linear characteristics of the primary and secondary instabilities for viscoelastic fluids saturating a porous horizontal layer heated from below by a constant flux. Galerkin method is used to solve the eigenvalue problem by taking into account the elasticity of the fluid, the ratio between the viscosity of the solvent and the total viscosity of the fluid and the lateral confinement of the medium. For the primary instability, we found out that depending on the rheological parameters, two types of convective structures may appear when the basic conductive solution loses its stability: stationary long wavelength instability as for Newtonian fluids and oscillatory convection. The effect of the lateral confinement of the porous medium by adiabatic walls is to stabilize the oblique and longitudinal rolls and therefore selects transverse rolls at the onset of convection. In the range of the rheological parameters where stationary long wave instability develops first, we use a parallel flow approximation to determine analytically the velocity and temperature fields associated to the monocellular convective flow. The linear stability analysis of the monocellular flow is performed, and the critical conditions above which the flow becomes unstable are determined. The combined influence of the viscoelastic parameters and the lateral confinement on the characteristics of the secondary instability is quantified. The major new findings concerning the secondary instabilities may be summarized as follows: (i) For concentrated viscoelastic fluids, computations showed that the most amplified mode of convection corresponds to oscillatory transverse rolls which appears via a Hopf bifurcation. This pattern selection is independent of both the fluid elasticity and the lateral confinement of the porous medium; (ii) For diluted viscoelastic fluids, the preferred mode of convection is found to be oscillatory transverse rolls for a very laterally confined medium. Otherwise stationary or oscillatory longitudinal rolls may develop depending on the fluid elasticity. Results also showed the destabilizing effect of the relaxation fluid elasticity and the stabilizing effect of the viscosity ratio for the onset of both primary and secondary instabilities.

The combination of calcium phosphates (CaP) with bioactive glasses (BG) has received an increased interest in the field of bone tissue engineering. In the present work, biphasic calcium phosphates (BCP) obtained by hydrothermal transformation (HT) of cuttlefish bone (CB) were coated with a Sr-, Mg- and Zn-doped sol-gel derived BG. The scaffolds were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR) and scanning electron microscopy (SEM). The initial CB structure was maintained after HT and the scaffold functionalization did not jeopardize the internal structure. The results of in vitro bio-mineralization after immersing the BG coated scaffolds in simulated body fluid (SBF) showed extensive formation of bone-like apatite onto the surface of the scaffolds. Overall, the functionalized CB derived BCP scaffolds revealed promising properties for their use in bone tissue engineering field.

We examined PT parameters, geochemical peculiarities, and fluid sources of the Ulug-Sair ore occurrence attributable to class of intrusion-related gold deposits and according to ore mineral assemblages corresponding to Au-Bi type with wide Bi minerals (AgBiTe, Bi2Te2Se, Cu3,07BiS3, Bi), tellurides (Au and Ag), Se-tellurides (Ag and Bi), and selenides (Au, Ag, and Hg). We identified that ‘pre-gold’ quartz-tourmaline veins were deposited using an aqueous Mg-Na-K-chloride fluid with a salinity of 8–10 wt % NaCl eq. At 325–370 °C; host breasts were formed due to a CO2-water fluid containing CH4 and N2, with a salinity of 0,18–6,1 wt % NaCl eq. at least 200–400 °C. Gold-bearing mineral assemblages were formed at P ~ 0,75–1,0 kbar (~ 2,3–3 km) due to CO2-water chloride (Na-K±Fe, Mg) fluid with CH4, Na2SO4, and Na2B2O5, and salinities 1,7–12,5 wt % NaCl eq. during the decreasing temperatures from 360 up to 115 °C (gold-sulfide-quartz veins – 360–130 °С, and gold-telluride-sulfide-quartz veins – 330–115 °C) and variations fO2, fS2, fSe2, and fTe2. The isotopic composition of δ34SH2S fluid (-0,7…+2,5 ‰) indicates the juvenile or magmatic origin of fluid and ore elements. The δ34OH2O fluid indicates that, at an early substage, the formation of ore occurrence involved a fluid of magmatic or metamorphic origin (+7,3…+11,4 ‰), and, in the later substage, it mixed with meteoric waters (-2,3…+9,1 ‰).

The therapeutic, attenuative, and morphological effects of proprietary neural stem cell-derived extracellular vesicles (NSC EVs, AB126) produced by Aruna Bio, Inc. were assessed in a range of in vitro and in vivo models of stroke. We emphasize that modulation of neuroinflammation is a key target and suggest further studies to advance our understanding of the mechanisms of action and ultimately how best to dose and monitor the benefits of AB126 in stroke patients.

This article objectively assesses, the hypothesis of the streamline's shape theory and its formulated equation. The deduction of proof uses algebra rather than first-order partial differential equations to address the specific hypothesis of "Streamline's shape theory" from the fundamental perspective of applied mathematics and scientifically derives mathematical relations of the axioms and corollaries in the field of fluid dynamics. The algebraic methods employed provide progressively more distinct and precise solutions compared to first-order partial differential equations. The foremost objective of this work is to evaluate if the formulations of the streamline's shape theory can have solutions for inviscid-incompressible and viscid-compressible flows of Newtonian fluids and to identify their nature. Secondly, to understand how the topology of the body and the free-stream conditions affect these solutions with due regards to the shape and size of the body interacting with the fluid flow. Finally, to explore the possibility of this theory to develop a CFD solver for streamline simulation to reduce the experimentation in the analysis of flow-structure interactions of Newtonian fluids and also to identify its scope of applications and limitations.

This investigation aimed to explore the impact of acute and regular physical exercise on Brain-Derived Neurotrophic Factor (BDNF) levels in individuals with obesity. Using the Population, Intervention, Comparator, Outcome, and Study design (PICOS) approach, the inclusion criteria were defined as follows: i) population - individuals with overweight or obesity of any age or gender; ii) intervention - acute or chronic interventions involving aerobic or anaerobic methodologies; iii) comparator - for acute effect studies, pre- and post-evaluations served as comparators, while interventions included at least one experimental group or the inclusion of a control group; iv) outcome - BDNF variability concerning the applied methodology; v) study design - restricted to experimental studies exclusively. Conducted in August 2022, the searches were carried out on PubMed, Academic Search Complete, and Web of Science. The risk of bias was assessed using the Risk of Bias in Non-randomized Studies (RoBANS) tool. Out of 98 potentially relevant articles, 16 met the eligibility criteria, encompassing 23 trials. Substantial heterogeneity was observed for both acute (I2 = 80.4%) and long-term effects (I2 = 88.7%). Additionally, RoBANS analysis indicated a low risk of bias for the included studies. The study's findings revealed a significant increase in the concentration of circulating BDNF in individuals with obesity compared to the control group following acute exercise. However, such an effect was not evident in the context of long-term physical exercise, with a small effect size (ES = 0.49) recorded in the latter scenario. The observed significant increase in BDNF levels post-acute exercise suggests a potential acute response mechanism contributing to the intricate interplay between exercise and neurotrophic factors in this population. Nevertheless, the absence of a similar effect in the context of long-term physical exercise implies a potential adaptation or ceiling effect. These findings underscore the importance of considering both the duration and nature of exercise interventions when exploring the neurobiological responses associated with obesity and exercise. The study provides valuable insights for future research and clinical implications in understanding the nuanced relationship between exercise, neurotrophic factors, and obesity.

Marine yeasts have versatile applications in industrial, medical and environmental fields, but have received little attention compared to terrestrial yeasts and filamentous fungi. In this study, a phylogenetic analysis of 11 marine-derived yeasts was conducted using internal transcribed spacers and nuclear large subunit rDNA, and their bioactivities, such as antioxidant, antibacterial, and tyrosinase inhibition activities, were investigated. The 11 marine-derived yeasts were identified to belong to seven species including Geotrichum candidum, Metschnikowia bicuspidata, Papiliotrema fonsecae, Rhodotorula mucilaginosa, Vishniacozyma carnescens, Yamadazyma olivae, and Yarrowia lipolytica, and three strains of these were candidates for new species of the genera Aureobasidium, Rhodotorula, and Vishniacozyma. Most extracts showed antioxidant activity, whereas seven strains exhibited antibacterial activities against Bacillus subtilis. Only Aureobasidium sp. US-Sd3 among the 11 isolates showed tyrosinase inhibition. Metschnikowia bicuspidata BP-Up1 and Yamadazyma olivae K2-6 showed notable radical-scavenging activity, which has not been reported previously. Among the isolates, Aureobasidium sp. US-Sd3 exhibited the highest antibacterial and tyrosinase inhibitory activities. Overall, our results demonstrate the potential of marine-derived yeasts as a source of bioactive compounds for improving industrial applications.

A new set of alkoxy alcohols were synthesised by reaction of eugenol oxirane with aliphatic and aromatic alcohols. These eugenol derivatives were evaluated against their effect upon the viability of the insect cell line Sf9 (Spodoptera frugiperda).The most promising compounds, 4-(3-(tert-butoxy)-2-hydroxypropyl)-2-methoxyphenol and 4-(2-((4-fluorobenzyl)oxy)-3-hydroxypropyl)-2-methoxyphenol were submitted to in silico assays to predict possible targets. Thought an Inverted Virtual Screening approach, 23 common pesticide targets were screened and the top 2 targets predicted were further evaluated through molecular dynamics simulations and free energy calculations. In addition, these to eugenol derivatives were subjected to encapsulation and release assays using liposome-based nanosystems of egg phosphatidylcholine/cholesterol (7:3), with encapsulation efficiencies higher than 90% and release profiles well described by both Korsmeyer-Peppas and Weibull models.

Human induced pluripotent stem cell (iPSC)-based model systems can be used to produce blood cells for the study of both hematologic and non-hematologic disorders. This commentary discusses recent advances that have utilized iPSC-derived red blood cells, megakaryocytes, myeloid cells, and lymphoid cells to model hematopoietic disorders. In addition, we review recent studies that have defined how microglial cells differentiated from iPSC-derived monocytes impact neurodegenerative disease. Related translational insights highlight the utility of iPSC models for studying pathologic anemia, bleeding, thrombosis, autoimmunity, immunodeficiency, blood cancers, and neurodegenerative disease such as Alzheimer’s.

Renewable resources gain increasing interest as source for environmentally benign biomaterials, such as drug encapsulation/release compounds, and scaffolds for tissue engineering in regenerative medicine. Being the second largest naturally abundant polymer, the interest in lignin valorization for biomedical utilization is rapidly growing. Depending on resource and isolation procedure, lignin shows specific antioxidant and antimicrobial activity. Today, efforts in research and industry are directed toward lignin utilization as renewable macromolecular building block for the preparation of polymeric drug encapsulation and scaffold materials. Within the last five years, remarkable progress has been made in isolation, functionalization and modification of lignin and lignin-derived compounds. However, literature so far mainly focuses lignin-derived fuels, lubricants and resins. The purpose of this review is to summarize the current state of the art and to highlight the most important results in the field of lignin-based materials for potential use in biomedicine (reported in 2014–2018). Special focus is drawn on lignin-derived nanomaterials for drug encapsulation and release as well as lignin hybrid materials used as scaffolds for guided bone regeneration in stem cell-based therapies.

Woodland strawberry (Fragaria vesca L.) is an underutilized plant species, appreciated by consumers for its qualitative features. Utilizing technical means of production, such as plant biostimulants, that can increase crop productivity and quality could be highly important in woodland strawberry cultivation. The scope of the present study was to appraise the influence of two biostimulants (Trichoderma atroviride and plant protein hydrolysate) - used either alone or combined - on plant performance and economic profitability of two woodland strawberry genotypes (‘Alpine’ and ‘Regina delle Valli’). Overall, data showed that ‘Alpine’ had the highest productive performances, whereas ‘Regina delle Valli’ revealed the highest fruit qualitative traits. T. atroviride inoculation and V-PH application significantly boosted plant marketable yield (+20.5% for T. atroviride and +12.9% for V-PH), total sugars (+1.9% for Trichoderma and +1.4% for V-PH) and anthocyanins (+14.1% for T. atroviride and +9.8% for V-PH) compared to non-treated plants. Plants supplied with both biostimulants had higher marketable yield (+34.8%), mean fruit weight (+6.0%), fruit dry matter (+13.8%), total sugars (+3.5%), ascorbic acid (+12.7%), flavonoid (+26.3%) and anthocyanins (+29.9%) compared to non-treated plants. Furthermore, our study revealed that the highest fruit polyphenols concentration was recorded in both genotypes treated with the combination of biostimulants and in ‘Regina delle Valli’ sprayed with V-PH, whereas the highest antioxidant activity was found in ‘Regina delle Valli’ fruit when plants were supplied with both biostimulants. Our study pointed out that the application of microbial and non-microbial biostimulants, especially in combination, might be an useful strategy for improving performances of underutilized species and, therefore, encourage its cultivation, valorisation and economic profitability (+10195.3 €/ha when plants were exposed to both biostimulants).

Healthcare faces a major problem with the increased emergence of antimicrobial resistance due to the over-prescription of antibiotics. This causes dysbiosis and major disruption of the gut microbiome, leading to the development of intestinal diseases, abnormalities in the regulation of immune responses, malfunctioning of entero-endocrine signaling, and an imbalance in communication with the central nervous system (CNS). Bacteriophages may provide a solution to the treatment of bacterial infections given their specificity. This approach increased rapidly over the last ten years, because of the rapid rise of multi-drug-resistant bacteria worldwide coupled with a decline in the development and production of novel antibacterial agents. Eradication of multidrug-resistant bacteria is often only possible with bacteriophage treatment. Phage proteins are used to stimulate immune responses against specific pathogens, improve antibiotic susceptibility, prevent biofilm formation, and characterize bacterial pathogens. This review discusses the therapeutic potential of bacteriophage-derived proteins.

New corrosion inhibitor derived from coumarin-3-amine namely 3-((2-chlorobenzylidene)amino)coumarin was synthesized and characterized by CHN elemental analysis in addition to Fourier transform infrared and nuclear magnetic resonance techniques. The anti-corrosion ability of 3-((2-chlorobenzylidene)amino)coumarin to inhibit the impacts of corrosion has been demonstrated and damage reduction of the mild steel also. 3-((2-chlorobenzylidene)amino)coumarin, has been employed as a good corrosion inhibitor for mild steel in HCL solution. The efficiency of the inhibition was figured according to weight loss method and it was 74.6%.

Extracellular vesicles (EV) are a very heterogeneous group of cell-derived vesicles released by almost all kind of living cells. EV are involved in intercellular communication, both locally and systemically, since they induce signals and transfer their contents (proteins, lipids, RNAs) to other cells, which subsequently trigger a wide variety of biological responses in the target cells. How-ever, cell surface receptor-induced EV release is limited to cells from the immune system, includ-ing T lymphocytes. T cell receptor activation of T lymphocytes induces secretion of EV containing T cell receptor for antigen and several bioactive molecules, including proapoptotic proteins. These EV are thus specific for antigen-bearing cells, which make them ideal candidates for a cell-free, EV-dependent cancer therapy. In this review we discuss the generation of EV by T lymphocytes and some potential therapeutic approaches of these EV.

Antibiotics are commonly used to treat infectious diseases. However, massive and inappropriate antibiotics usage cause many problems including the emergence and spread of antibiotic-resistant bacteria. To avoid this issue, in modern countries the interest of using probiotics in feed supplementation to promote health and prevent or treat intestinal infectious diseases in companion animals like dogs has been increasing. We evaluate the probiotic potential of Lactobacilli isolated from healthy dogs faeces. The isolated Lactobacilli were first confirmed by 16SrRNA sequencing, then in vitro tests were conducted to assess survival potential of Lactobacilli under simulated gastrointestinal conditions and adhesion ability to gut epithelia, effects on epithelial barrier function, anti-inflammatory activities, effects on defensin peptides (beta-defensin 3) and inhibitory effects on common pathogens. Lactobacilli showed considerable potential to survive in simulated gastrointestinal environmental conditions, low pH, high bile salt concentrations along with good adhesion properties with MODE-K cells. Pathogenic bacterial growth and their adhesion to MODE-K cells was significantly inhibited by Lactobacilli. Real-time PCR analyses further demonstrated that L. acidophilus strain AR1 and AR3 inhibit Salmonella-induced proinflammatory cytokines (IL-6, IL-8, 1ꞵ) production and reinforce expression of tight junction protein (occludin). None of the strain induce mRNA expression of beta-defensin 3 in MODE-K cells. Based on in vitro results the L. acidophilus strain AR1 has potential to be supplemented in canine feed. However, further in vivo studies investigating health-promoting effects are awaited.

The World Health Organization declared the coronavirus disease 2019 (COVID-19) pandemic in 2020, following which a global genetic vaccination program has been rapidly implemented as a fundamental solution. However, it has been reported worldwide that the modified mRNAs encoding spike proteins and lipid nanoparticles, which are used as drug delivery systems, not only cause thrombosis and cardiovascular disorders post vaccination, but might also cause diverse diseases involving all organs and systems, including the nervous system. Furthermore, the toxicity and pathogenicity of spike proteins may necessitate defining these proteins as nonbiological infective material. Based on these reports and the abundant evidence that has come to light in the past few years, this paper aims to draw the attention of medical professionals to the various risks associated with transfusion using blood products derived from long COVID patients or from genetic vaccine recipients, and to make proposals regarding specific inspection items, testing methods, regulations, etc. This paper provides insights to address the post-vaccination syndrome and its consequences following such genetic vaccination programs.

Per- and polyfluoroalkyl substances (PFASs) are a group of fluorinated, organic, man-made chemicals; they do not occur naturally in the environment. This study aimed to determine the profile and content of PFASs in volunteers’ blood plasma and urine after fermented red beetroot juice consumption and correlated it with the blood parameters. During 42 days, 24 healthy volunteers intake 200 mL/60 kg of body weight fermented red beetroot juice. PFASs were analyzed using micro-HPLC-MS/MS method. Five perfluoroalkyl substances were found in human body fluids. After juice consumption, PFASs, due to the consumption of food contaminated with them, was discovered that for perfluorocarboxylic acids, a downward trend was observed, while for perfluoroalkane sulfonates, their plasma content showed a statistically significant upward trend. Analysis of the hematology parameters indicated that the intake the fermented red beetroot juice showed a significant decrease in mean corpuscular volume (MCV), platelets concentration, mean platelet volume (MPV), platelet large cell ratio (P-LCR) at the significance level p < 0.01, and he-matocrit (p < 0.05). On the other hand, the dietary intervention also indicated a significant (p < 0.01) increase corpuscular/ cellular hemoglobin concentration (MCHC). In the case of blood biochemi-stry, no significant change in blood samples after intake the fermented beetroot juice was observed. However, a decreasing tendency of total cholesterol and low-density lipoprotein concentration (LDL-C) were observed. Based on the presented results, there is a need to analyze and monitor health-promoting food regarding undesirable substances and their impact on consumer health.

Registration of the flow pattern fine structure and the matter distribution of a free falling liquid drop in a target fluid at rest in the impact mode of coalescence, when the kinetic energy of the drop exceeds its available potential surface energy (APSE), was carried out by photo and video recording. The main attention was paid to the study of the flow structure at the initial stage of the cavity formation. To carry out color registration, the flow pattern was illuminated by several matrix LED and fiber optic sources of constant light. The planning of experiments and interpretation of the results were based on the properties of the complete solutions of the fundamental equations of fluid mechanics system, including the transfer and conversion of energy processes. Complete solutions of the system of equations describe large-scale flow components that are waves or vortices as well as thin jets (ligaments, filaments, fibers, trickles). In experiments, the jets are accelerated by the converted available potential surface energy (APSE) when the free surfaces of merging fluids were eliminated. The experiments were performed with the coalescence of water, solutions of alizarin ink, potassium permanganate, copper sulphate or iron sulphate drops in deep water. In all cases, at the initial contact, the drop begins to lose its continuity and breaks up into a thin veil and jets, the velocity of which exceeds the drop contact velocity. Small droplets, the size of which grows with time, are thrown into the air from spikes at the jet tops. On the surface of the liquid, the fine jets leave colored traces that form linear and reticular structures. Part of the jets penetrating through the bottom and wall of the cavity forms an intermediate covering layer. The forming layer jets are separated by interfaces of the target fluid. The processes of molecular diffusion equalize the density differences and form an intermediate layer with sharp boundaries in the target fluid. All noted structural features of the flow are also visualized when a fresh water drop isothermally spreads in the same tap water. The fast-changing and finely structured diffuse boundary of merging fluids, which at the initial stage has a complex and irregular shape, is gradually smoothed out by molecular diffusion processes. The similar flow patterns were observed in all performed experiments, however the geometric features of the flow depend on the individual thermodynamic and kinetic parameters of the contacting fluids.

Introduction: Some of the practices in medicine are carried out of habit without proven benefits. This is the case of premature babies from 30 to 34 weeks of gestation who are always given parenteral fluids, even though this practice has been associated with an increase incidence of infection. At the end of 2017, we started a protocol of rationalization in the use of parenteral fluid. To administer nutrition/fluids, we used oral fluids by suction if this was possible or otherwise by oral/nasogastric tube at volumes of 70-80 mL/Kg/day divided every 3 hours, with 5 mL increments every 12-24 hours until 200 mL/K/day was achieved, always using breast milk when possible. Material and methods: The present study sought to compare results before and after this new policy. For this work, we review all premature babies between 30-34 weeks of gestation in two time periods, the first from 01/01/2010 to 12/31/2017 and the second from 01/01/2018 to 08/15/2022. The number of cases with and without parenteral fluids (PF), the incidence of infection, the weight at admission and discharge, and the change in the weight Z score between birth and discharge were compared. Both the anthropometric and outcome variables were compared using the different statistical methods according to each variable. Results: were found 920 cases with the described characteristics. The groups before and after the intervention did not show significant differences in their general demographic characteristics. We observed a decrease use of PF in the second period, from 425 cases (82.0%) before to 297 (26.2%) after implementation, p <0.0001 and fewer days of use (4.1 days/average before vs 1.3 after, p <0.0001) of PF. The weight at discharge and the change in weight Z-score were the same in both groups. Infections went from nine cases before to two cases after but it was not statistically significant. There were no complications due to less use of PF. Discussion: This study showed that the use of PF is not associated with significant changes in outcomes of interest, which reinforces that its use does not generate any benefit for the patient. Larger number of cases is required to detect differences in low incidence events such as infections.

Periodontitis is microbial infection affecting periodontium, the tooth supporting structure and affects >743 million people worldwide. Neural crest-derived stem cells (NCSCs) hold the promise to regenerate the damaged periodontium. These cells have been identified within adult adipose tissue, periodontal ligament, and palatal tissue. Typical enzymatic isolation protocols are expensive, time consuming and often not clinically compliant. Enzyme-free, mechanical dissociation has been suggested as an alternative method of generating cell suspensions required for cell separation and subsequent expansion ex vivo. In our study, samples of rat skeletal muscle tissue were used to appraise the suitability of a novel mincing method of mechanical dissociation against enzymatic digestion with collagenase and dispase. Skeletal muscle is readily available and has been shown to contain NCSC populations. We used a Rigenera-Human Brain Wave^® prototype mincer to produce a suspension of skeletal muscle-derived cells modeling NCSCs. We have compared the resulting cell cultures produced via mechanical dissociation and enzymatic dissociation, producing single cell suspensions suitable for Magnetic Cell Sorting (MACs) and Fluorescence-activated cell sorting (FACS). Despite the Countess Automated Cytometry data demonstrating that cell suspensions produced by mechanical dissociation (n=24) contain on average 26.8 times as many viable cells as enzymatic cell suspensions (n=18), enzymatic suspensions produced more successful cell cultures. Spheroids and subsequently adherent cells formed from 4 enzymatic cell suspensions (44.4%) vs. 1 mechanical cell suspension (8.3%). Enzymatic digestion protocols formed spheroids faster and more plentifully than mechanical cell suspensions. Adherent cells and spheroids isolated via both methods appear morphologically similarly to NCSCs from our previous studies.

Obesity entails metabolic alterations across multiple organs, highlighting the role of inter-organ communication in its pathogenesis. Extracellular vesicles (EVs) are communication agents in physiological and pathological conditions and although they have been associated with obesi-ty-comorbidities, their protein cargo in this context remain largely unknown. To decipher the messages encapsulated in EVs, we isolated plasma derived EVs from diet induced obese murine models. Obese plasma EVs exhibited a decline in protein diversity while control EVs revealed significant enrichment in protein folding functions, highlighting the importance of proper folder in maintaining metabolic homeostasis. Previously, we revealed that gut derived EVs proteome holds particular significance in obesity. Here, we compared plasma and gut EVs and identified four proteins exclusively present in the control state of both EVs, revealing the potential for a non-invasive assessment of gut health by analyzing blood derived EVs. Given the relevance of post-translational modifications (PTMs), we observed a shift in chromatin-related proteins from glycation to acetylation in obese gut EVs, suggesting a regulatory mechanism targeting DNA transcription during obesity. This study provides valuable insights into novel roles of EVs and protein post-translational modifications in the intricate mechanisms underlying obesity, shed-ding light on potential biomarkers and pathways for future research.

Tomato quality is intricately regulated by a combination of factors, including the presence of bioactive compounds referred to as secondary metabolites and various organoleptic characteristics. These attributes are notably influenced and harmonized by the specific growing conditions, with a particular emphasis on the type of fertilization employed. Traditionally, chemical fertilizers have been favoured in crop cultivation due to their cost-effectiveness and ability to accelerate crop growth. However, in pursuit of sustainable and intelligent agricultural practices, there is a growing need for alternative fertilizers. In this context, the present study aimed to assess the impact of fertilizers derived from waste materials, specifically sulphur bentonite and orange residue (referred to as SB), on tomato quality. This assessment extended to examining qualitative and quantitative alterations in aroma-related volatile compounds and the antioxidant systems of tomatoes, in comparison to the conventional use of fertilizers such as horse manure and NPK (nitrogen, phosphorus, and potassium). The results obtained revealed distinct effects of different fertilizers on tomato quality. Notably, parameters such as TPRO (total protein), TCARB (total carbohydrate), LIC (lycopene content), TCAR (total carotenoid content), total phenols, total flavonoids, and aroma profiling exhibited significantly superior values in the group treated with SB fertilizer. These findings strongly suggest that the novel fertilizer functioned as a bio-stimulant, enhancing the nutraceutical and sensory attributes of tomatoes, with a pronounced impact on the synthesis of secondary metabolites and the aroma profile of the fruits.