The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Non-invasive continuous health monitoring has become feasible with the advancement of biosensors. While monitoring certain biomarkers such as heart rate or skin temperature are now at certain maturity, monitoring molecular biomarkers is still challenging. Progress has been shown in sampling, measurement and interpretation of data towards non-invasive molecular sensors that can be integrated in daily wearable items. Towards this goal, this paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. In controlled experiments, we have shown the variation of glucose concentration in water can be wirelessly detected by tracking the resonant frequency of the embroidered sensors. The current sensors operate at 1.8GHz–2GHz and respond to the change of glucose concentration with a sensitivity of 0.17 MHz/(mg/dl). The embroidered IDT-based sensors with wireless sensing will be a new measurement modality for molecular wearable sensors. The establishment of a wireless sensing mechanism for embroidered IDT-based sensors will be followed by investigation of sweat for molecular detection. This will require adding functionalities for sampling and interpretation of acquired data. We envisage the embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

During 2021 and 2022 summers, we measured the total and dissolved (< 0.45 mm) concentration of 25 elements in Utah Lake using Inductively Coupled Plasma Optical Emission Spectrometry (ICP-OES). Utah regulates twelve of these elements. ICP-OES sensitivity is at the ppb-level but is not the approved regulatory method. All regulations are for dissolved concentrations; except aluminum (Al) and phosphorus (P) which are for total recovery. We found total Al concentrations above allowable, but dissolved concentrations were well below allowable concentrations. We attribute high total concentrations to suspended clays. Dissolved copper (Cu) concentrations were below regulatory levels in 2021, but some samples were above regulatory levels in 2022. This could be related to the use of Cu-based algaecide treatments, or from other sources. Lead (Pb) data were inconclusive; dissolved Pb concentrations were well below the acute (1-hour average) limit, but the chronic concentration limit (4-hour average) is below the ICP-OES minimal detection limit. Arsenic (As) concentrations exhibit a seasonal trend that we attribute to groundwater inflows. This ppb-level study provides insight into regulated elements in Utah Lake previously not available due to the high sensitivity of the method and measurements of both total and dissolved concentrations.

Dogs population increased exponentially in the past decade while the birth rate decreased gradually, especially in the developed countries. Due to dogs’ characteristics of loyalty and obedience, most pet owners treated their dogs as their family members or companions, therefore they are willing to select and purchase safe, high quality and nutrition dog food to their dogs. However, there is lack of regulation or standard to reinforce the production or distribution of dog food in Hong Kong. Consequently, this paper will first review the relationship between high dog population and declining birth rate, types of dog food and typical ingredients. Secondly, the potential health implications of various “toxic” food ingredients for dog, hazard analysis of dog food and its testing methods will be investigated. Lastly, this paper will summarize worldwide existing standards and regulations, quality and hygiene management system related to dog food safety to provide insights and suggestions to Hong Kong government about the importance and urgency of implementing regulations and policies to oversee the imported and local manufactured dog food.

This paper presents a methodology based on deep learning models and metaheuristic algorithms for the optimization of airfoils for the design of aircraft wings with large endurance. The use of AZTLI-NN (a neural network with an architecture composed of a multilayer perceptron and a variational autoencoder) is implemented for the prediction of graphs of the aerodynamic coefficients of the airfoil as a function of the angle of attack. This neural network presents good predictions of the aerodynamic coefficients, similar to the coefficients obtained with computational fluid dynamics simulations. AZTLI-NN in combination of metaheuristic algorithms and the CST profile parameterization method show excellent performance in single-objective and multi-objective profile optimization tasks.

Segregating one space from another is a rudimentary act of architecture and the basic principle of this act is creating differentiation between outside and inside. Thresholds, in their expanded or summed form, also produce spaces. They establish the staging for threshold areas in conjunction with space-defining elements. Threshold spaces are typically complicated spatial formations that serve as transition points. They pose a challenge to the interacting human senses in terms of perception. In this research threshold areas have been studied under a specific typology of architecture i.e the traditional housing in historic cities of India. The traditional dwelling settlements have evolved and grown over multiple layers of history, influenced by the culture, society, economy, climate and topography. The purpose of this research is to examine the characteristics of these transition spaces of the traditional dwelling units in relation to the symbolic reference and social meanings assigned to them that influence the architectural and urban spaces attached to them. It seeks to describe transition space in terms of its nature, character, morphology, and social significance. Transparency and material articulation, as well as hierarchy and enclosure, will be investigated. The importance and quality of the nature of "transition" will be examined from the inside to the outside. The research reveals that the space has great functional and socio-cultural importance. It allows multiple activities, provides protection from sun and rain, defines boundaries, connects people within the neighborhood, enhances security and gives an identity to the owner. The contributions made by this research have the potential to improve design considerations for transition areas between the dwelling units and the street.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

Groundwater is becoming increasingly important in the Pacific Northwest of the USA due to declining snowpack volumes and shifts in precipitation type and timing, all connected with climate change. The Upper Williamson Basin of the Klamath Watershed is a groundwater dominated watershed with massive fluctuations in year-to-year streamflow volumes over the past four decades, including the complete absence of any live flow for several years. The precise relationship between groundwater and streamflow in the basin has been difficult to assess due to a limited number of monitoring wells and significant gaps in the water level time history. To address this challenge, we use a novel imputation technique that leverages Earth observations and machine learning to impute gaps in water level records. We use these more complete datasets to compute a groundwater storage change time series for the basin. We show that groundwater storage is highly correlated to streamflow and that groundwater storage is correlated to rainfall with a three- to four-year delay that appears variable depending on groundwater storage volumes. The tools and relationships we present make it possible for water managers to estimate when streamflows will return to the basin and be more informed to support better management.

Protection suit is vital for fireman’ safety. Traditional protection suit just physically protects fireman from empyrosis, but can not locate the body injury position from the impact debris. Herein, we present a wearable impact debris positioning system for fireman protection suit alarming based on accelerometer array. The wearable piezoelectric accelerometers with distribute regularly on the suit to detect the vibration on different body parts, which is conducive to positioning injured body parts. In addition, the injured parts can be displayed on the dummy body model on the upper computer with a higher localization accuracy of 4 cm. The positioning alarm system has a rapid response time of 0.11ms attributing to smart signal processing method. This work provides a reliable and smart method for locating and assessing the body injury position from the impact debris, which is significant for fire disaster commander to rescue injured fireman in time.

This work discusses seismic isolation technologies and analyses the concept of geotechnical seismic isolation (GSI) system, which is characterized by new principles of operation, using geomaterial with modified properties to reduce inertial seismic loads on buildings and structures. The aim of the study is to develop a geotechnical seismic isolation system in the form of vertical barriers, with different geometrical characteristics, using rubber-soil mixture (RSM). The novelty of the work consists in determination of effective constructive and technical solutions of vertical seismic barriers from RSM, which are characterized by reliability in providing seismic isolation of construction objects. Soil and superstructure interactions are modeled in Plaxis software, using the Northridge earthquake accelerogram. The results confirm the positive impact of using RSM as an effective material for GSI vertical barriers. The present numerical and experimental results show that the GSI system using RSM can significantly reduce the seismic hazard. The results of computational-experimental modeling will become a research, analytical and design basis for the development of new ways to ensure earthquake resistance of construction objects.

Making sustainable business models, especially in manufacturing, is a key approach for organizations to adopt in order to create more sustainable processes. New technologies are needed to implement new policies that can minimize the economic, environmental, and social consequences of industrial activity. Sustainable maintenance is decisive to guarantee the availability, reliability, and safety of assets, surpassing traditional maintenance policies and embracing the principles of the circular economy. The main objective of Maintenance 4.0 is to increase the lifespan and availability of the equipment by preventing unplanned downtime, reducing planned shutdowns, and improving safety. This research focuses on the integration of advanced Industry 4.0 tools with conventional monitoring and control techniques in process industries. The article suggests that while complex neural networks might provide good predictions, simpler solutions can generalize well and have lower prediction errors because they can capture the underlying relationships between variables in a specific asset better. The combination of maintenance function, Industry 4.0 tools, and advanced statistical solutions to obtain sustainable processes can facilitate organizational change and aid decision-making in equipment management. These solutions seek to reduce interruptions and expenses through the unnecessary utilization of labor and spare parts. All these considerations improve communication and data processing, resulting in improved maintenance of a hydrogen compressor in the petrochemical industry.

This study explores the current landscape of social value (SV) research in the construction industry, analyzing global trends and identifying future research directions. Using bibliometric analysis, research published in Elsevier Scopus database from 2013 to 2023 was extracted using the keywords "social value" AND "construction industry." Results indicate a focus on social value indicators, socioeconomic impacts, project management, innovative practices, and cross-sector collaborations. The study also reveals a lack of attention to SV in African countries' construction sectors. By highlighting research areas and identifying gaps, this study contributes to academic literature, suggesting the need for guidelines, particularly in developing countries, and advocating for further research on SV in the built environment and strategies for global social value creation.

Volcanic activity essentially consists of the transfer of heat from the Earth’ interior to the surface. The precise signature of this heat transfer relates directly to the processes underway at and within a particular volcano and this can be observed, at a safe distance, remotely, using infrared sensors that are present on Earth-orbiting satellites. For over 50 years, scientists have perfected this art using sensors intended for other purposes, and they are now in a position to determine the particular sort of activity that characterizes different volcanoes. This review will describe the theoretical basis of the discipline and then discuss the sensors available for the task and the history of their use. Challenges and opportunities for future development in the discipline are then discussed.

The influence of short term water absorption on the mechanical properties of halloysite nanotubes-multi layer graphene reinforced polyester hybrid nanocomposites has been investigated. The addition of nano-fillers significantly increased the flexural strength; tensile strength and impact strength in dry and wet conditions. After short term water exposure; the maximum microhardness; tensile; flexural and impact toughness values were observed at 0.1 wt% MLG. The microhardness increased up to 50.3%; tensile strength increased up to 40% and flexural strength increased up to 44%. Compared to dry samples; the fracture toughness and surface roughness of all types of produced nanocomposites were increased that may be attributed to plasticization effect. Scanning electron microscopy revealed that the main failure mechanism is caused by the weakening of nano-filler-matrix interface induced by water absorption. It was further observed that synergistic effects were not effective at concentration of 0.1 wt% to produce considerable improvement in mechanical properties of produced hybrid nanocomposites.

One of the primary causes of the mechanical seal failure is rotor vibration. Traditional dynamic seal models often would not be able to fully explaining the failure mechanisms. The seal dynamic models proposed in this paper, including those developed by the authors, prove valuable in predicting seal dynamics during operation in specific turbomachinery and in explaining the causes of seal failure. The single-mass dynamic model is suitable for analyzing contact mechanical seal and simple design dry gas seals dynamics. The two-mass dynamic model is used for investigating operational dynamics processes in classical dry gas seals under complex loading conditions. The three-mass dynamic model is used to study various complex mechanical seal types. This model is able to determine the normal operating condition range and to explain leakage mechanisms in the presence of excessive rotor vibrations.

With the development of information technology and the wide application of building information modelling technology, the construction industry continues to make digital changes. Managers are trying to apply smart construction site management to promote the upgrading of production modes. We used CiteSpace software to analyze 1707 articles from China National Knowledge Infrastructure, Web of Science and Scopus to understand the current research hotspots of global scholars in this field. Results show that: (1) The number of studies on smart construction sites increases rapidly by year. Researchers from China, America and the UK have the most influential studies. (2) The cooperation between researchers and institutions is not close enough. In addition, the directions of research in the field are still scattered; (3) Chinese scholars are good at building intelligent platforms and evaluating intelligent systems from multiple perspectives. International scholars are willing to pursue technological innovation, allowing the continuous development of intelligent construction technology. (4) The applications in this field have not been popularized despite relatively perfect technology and typical cases. Future scholars should gradually improve the theoretical basis and industry standards of smart construction sites, promote the development of intelligent construction technology and establish the evaluation standards of qualified smart sites. This study will provide scholars in this field with the theoretical basis and research directions for further in-depth research, help construction companies to understand the development status and trend of smart construction sites and accelerate the intelligent transformation of construction companies.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

The decarbonization of the built environment, both in new construction and renovation, is crucial to mitigate its relevant impact on climate change and achieve the Paris agreement goals. This study presents a systematic LCA-based methodology to assess the whole life carbon emissions of buildings, applied to a proposal for the regeneration of one of Milan’s disused railway yards. As an entry for the 2020 Reinventing Cities competition, Scalo Lambrate is a project for a mainly residential neighborhood with a public park. Strategies to reduce carbon emissions deriving both from the operational energy and construction and maintenance were evaluated and their effects compared to a reference scenario over a time horizon of 100 years. The results show that, while the opportunities to reduce carbon emissions during the use phase are somehow limited due to the already stringent performance requirements for new builds, the use of fast-growing biogenic materials for construction materials, even if mixed with more traditional ones, can provide a significant reduction of the global warming potential over the whole life cycle, with a reduction of 70% over the baseline. The remaining emissions can be offset with afforestation initiatives that, however, must be assessed against land use issues.

A model for enabling the production of lower carbon cement paste is proposed in this research. The model is based on predicting the strength of cement pastes with partial replacement of wheat straw ash (WSA) and silica fume (SF), two major wastes of agricultural and industrial production. The model is set up based on response surface methodology and Box-Behnken design, and included a suite of mechanical tests with distinct replacements following a micro an meso characterization. The model shows capability for predicting strength of any cement paste, including partial substitution of WSA and/or SF at any combination level with excellent accuracy, which is verified with three validation mixtures demonstrating maximum errors of less than 6% at the three ages. The analysis of the response surface evidences that any cement replacement in the range of 0-20% WSA and above 5% SF allows the reduction of the carbon footprint by maximizing the incorporation of both wastes. The proposed model can be used by setting the required strength of cement paste and calculating the maximum possible replacement, which should contribute to making the construction industry more sustainable by utilizing local waste.

This article examines the impact of climate change on the hydrometeorological state of some lakes and reservoirs in the Akmola and North Kazakhstan regions. Time series with values of various climate parameters for the period 1986-2023 are used for the climate analysis; the reliability of the results was assessed using the Fisher criteria. Hydrometric indicators were studied using the ArcGIG program. Using GIS to spatially analyze water climate data, 8-channel satellite images from 1995 to 2023 were used. During the study, it was found that the area of the main lakes has undergone changes.

The transition to cleaner energy sources, particularly in hard-to-abate industrial sectors, often requires gradual integration of new technologies. Hydrogen, crucial for decarbonization, is explored as a fuel in blended combustions. Blending or replacing fuels impacts combustion stability and heat transfer rates due to differing densities. An extensive literature review examines blended combustion, focusing on hydrogen-methane mixtures. While industrial burners claim to accommodate up to 20% hydrogen, theoretical support is lacking. A novel thermodynamic analysis methodology is introduced, evaluating methane-hydrogen combustion using the Wobbe index. Findings highlight practical limitations beyond 25% hydrogen volume, necessitating a shift to "totally hydrogen" combustion. Blended combustion can be proposed as a medium-term strategy, acknowledging hydrogen's limited penetration. Higher percentages require burner and infrastructure redesign.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

With buildings accounting for a significant portion of global energy consumption and greenhouse gas emissions, the application of artificial intelligence (AI) holds promise for enhancing sustainability in the building lifecycle. This systematic literature review addresses the current understanding of AI's potential to optimize energy efficiency and minimize environmental impact in building design, construction, and operation. A comprehensive literature review and synthesis were conducted to identify AI technologies applicable to sustainable building practices, examine their influence, and analyze the challenges of implementation. The review was guided by a meticulous search strategy utilizing keywords related to AI application in sustainable building design, construction, and operation. The findings reveal AI's capabilities in optimizing energy efficiency through intelligent control systems, enabling predictive maintenance, and aiding design simulation. Advanced machine learning algorithms facilitate data-driven analysis and prediction, while digital twins provide real-time insights for informed decision-making. Furthermore, the review identifies barriers to AI adoption, including cost concerns, data security risks, and challenges in implementation. AI presents a transformative opportunity to enhance sustainability in the built environment, offering innovative solutions for energy optimization and environmentally conscious practices. However, addressing technical and practical challenges will be crucial for the successful integration of AI in sustainable building practices.

A two-stage pilot plant study has been completed that evaluated the performance of a reverse osmosis (RO) membrane process for the treatment of a feedwater that consisted of a blend of nanofiltration (NF) concentrate and brackish groundwater. Membrane performance was assessed by monitoring the process operation, collecting water quality data, and documenting the blended feedwater’s impact on fouling due to a combination of, or solely caused by, plugging, scaling, microbiological, or organic means. Fluorescence and biological activity reaction tests were used to identify the types of organics and microorganisms present in the blended feedwater. Additionally, scanning electron microscopy (SEM) and energy dispersive x-ray spectroscopy (EDS) were used to analyze suspended matter that collected on the surfaces of cartridge filters used in the pilot’s pretreatment system. SEM and EDS were also used to evaluate solids collected on the surfaces of 0.45-µm silver filter pads after filtering known volumes of NF concentrate and RO feedwater blends. Water quality analyses confirmed that the blended feedwater contained little to no dissolved oxygen, and the blended feedwater was absent of a significant amount of particulate matter as defined by silt density index and turbidity measurements. However, water quality results suggested that the presence of sulfate, sulfide, iron, anaerobic bacteria, and humic acid organics likely contributed to the formation of pyrite observed on some of the membrane surfaces autopsied at the conclusion of pilot operations. It was determined that first-stage membrane productivity was impacted by the location of cartridge filter pretreatment; however, second-stage productivity was maintained with no observed flux decline during the entire pilot operation’s timeline. Study results indicated that the operation of an RO process treating a blend of NF concentrate and brackish groundwater could maintain a sustainable and productive operation that provided a practical zero-discharge process operation while the dilution of RO feedwater salinity would lower overall production costs.

Studies have demonstrated the critical role that safety plays in preserving favourable working conditions in the construction industry, which is necessary to accomplish goals. The aim of this research was to inform stakeholders in the construction industry in developing nations about the value of safety and possible strategies for influencing their opinions regarding safety protocols. The importance of safety to the construction sector, which is crucial to the advancement of the country, has also been emphasized. However, due to a lack of adequate safety understanding among stakeholders in the construction sector, the construction industry is characterized by a great deal of instability and hazard. To determine what factors, affect productive working conditions in the construction production, this study examined safety. A conceptual framework for safe working conditions in the construction sector was developed by considering several aspects, including the person dimension, environment factor, safety behaviour, organization features, technology, and incentives. It is now imperative to bring in these dimensions to improve the safe working conditions in the construction industry, particularly in the developing countries. By putting these safety factors into practice, the construction industry can reduce safety risks, lower the number of accidents and fatalities, cut expenses related to subpar safety performance, safeguard the reputation of construction companies, boost employee morale and satisfaction with their work, enhanced employee retention, reduced absenteeism, and enhanced sustainability goals. Additionally, the proposed conceptual framework is assured to be new and to be widely accepted in the developing nations. Based on this assumption the conceptual framework is designed.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

The construction time of concrete structures in hydraulic tunnels is long, the construction environment is complex, and there are many influencing factors. The requirements for construction quality are high, not only to meet the strength requirements, but also to meet the design requirements of erosion resistance, crack resistance, and seepage resistance according to its specific operating environment. Therefore, evaluating the construction quality of concrete structures in hydraulic tunnels is of great significance. Considering the randomness and fuzziness of factors affecting the construction quality of concrete structures in hydraulic tunnels, this paper proposes a comprehensive evaluation model based on Combined Weighting (CWM) and Uncertainty Measurement Theory (UM). The IAHP method and CRITIC method are used to determine the subjective and objective weights of evaluation indicators, combined weighting is based on the principle of minimum entropy, and the UM method is used to evaluate the construction quality level. Finally, taking a hydraulic tunnel as an example, its construction quality grade is calculated to be III according to the evaluation model proposed in this paper, which matches with the engineering reality, and a comparative study is made with the mixture element topology theory at the same time. It is verified that the evaluation model can scientifically and reasonably evaluate the construction quality level of concrete structures in hydraulic tunnels.

Hybrid Renewable Energy Systems (HRES) integrate renewable sources, storage, and optionally conventional energies, offering an eco-friendly solution to fossil fuels. Microgrids (MGs) bolster HRES integration, enhancing energy management, resilience, and reliability at various levels. This study, emphasizing the need for refined optimization methods, investigates three themes: renewable energy, microgrid, and multiobjective optimization (MOO), through a bibliometric analysis of 470 Scopus documents from 2010-2023, analyzed with SciMAT software. It segments the research into two periods, 2010-2019 and 2020-2023, revealing a surge in MOO focus, especially in the latter period, with a 35% increase in MOO-related research. This indicates a shift towards com-prehensive energy ecosystem management that balances environmental, technical, and economic elements. The initial focus on MOO, genetic algorithms, and energy management systems has expanded to include smart grids and electric power systems, with MOO remaining a primary theme in the second period. The increased application of Artificial Intelligence (AI) in optimizing HMGS within the MOO framework signals a move towards more sustainable, intelligent energy solutions. Despite progress, challenges remain, including high battery costs, the need for reliable MOO data, the intermittency of renewable energy sources, and HMGS network scalability issues, highlighting directions for future research.

In this study, carbon-quantum-dot (CQD)-decorated TiO2 was prepared using an ultrasonic doping method and applied in the photocatalytic degradation of naphthalene under sunlight irradiation. The CQDs were synthesized from a typical macroalgae via diluted sulfuric acid pretreatment and hydrothermal synthesis using an optimal design, i.e., 3 wt% and 200 oC, respectively. The CQD/TiO2 composite remarkably enhanced the photocatalytic activity. The degradation of naphthalene under a visible light environment indicated that there is a synergistic mechanism between CQDs and TiO2, in which the generation of reactive oxygen species is significantly triggered; in addition, the N that originated from the macroalgae accelerated the photocatalytic efficiency. Kinetic analysis showed that the photo-catalytic behavior of the CQD/TiO2 composite followed a pseudo-first-order equation. Consequently, our combined experimental approach not only provides a facile pretreatment process for bio-CQDs synthesis, but also delivers a suitable TiO2 photocatalyst for up-conversion, along with critical insights into the development of harmful macroalgae resources.

With the continuous emergence and application of new technologies, the construction of smart cities has entered the practical promotion period. Since 2012, the pilot construction of smart city has been promoted by the government in China. On the basis of these practical experiences, this paper presents an overview of the latest technologies and applications for smart city construction in China and demonstrates that smart city strategy needs to be implemented according to local conditions, adhering to the people-oriented concept and using scientific and effective top-level design and planning. The construction of smart city is comprehensive system engineering, including the integration of geographic information sharing service platform, full-cycle management and control system of urban planning, construction and social management, as well as intelligent business information management system of gardening, water conservancy, environmental protection and other industries and departments. The information system (GIS), satellite remote sensing (SRS), global navigation satellite system (GNSS), Internet of things, mobile applications, cloud computing, visualization technology ware used to promote urban construction and sustainable development, and to meet the needs of future smart city development. Results show that centralized management is very important for the construction of smart city. The government plays a major role in the construction of smart city, which will be conducive to the development of new technologies and the effective use of smart city construction resources.

The optimal structural design is imperative to minimize material consumption and reduce the environmental impact of construction. Given the complexity in the formulation of structural design problems, the process of optimization is commonly performed using artificial intelligence (AI) global optimization, such as Genetic Algorithm (GA). However, the integration of AI-based optimization together with visual programming (VP) in building information modeling (BIM) projects warrants further investigation. This study proposes a workflow by combining structure analysis, VP, BIM, and GA to optimize trusses. The methodology encompasses several steps including: (i) generation of parametric trusses in Dynamo VP; (ii) performing the finite element modeling (FEM) using Robot Structural Analysis (RSA); (iii) retrieving and evaluating the FEM results interchangeably between Dynamo and RSA; (iv) finding the best solution using GA; and (v) importing the optimized model into Revit, enabling the user to perform simulations and engineering analysis, such as life cycle assessment (LCA) and quantity surveying. The feasibility of the proposed workflow was tested on benchmark problems and compared with open literature. The outcomes of this study offer insight into the opportunities and limitations of combining VP, GA, FEA, and BIM for structural optimization applications, particularly to enhance structural efficiency and sustainability in construction.

Due to the inherent risks associated with tunnel construction, including potential collapse, various types of work activities, and challenging visibility and communication conditions, safety management in tunnel projects requires significant investment in terms of cost and time. In this research, we propose and demonstrate a novel smart construction system that utilizes worker location monitoring technology to enhance safety in tunnel construction. The system comprises a wearable beacon integrated into safety helmets, scanners strategically placed at regular intervals inside the tunnel, environmental sensors for monitoring temperature, pressure, and air quality, and mobile devices for collecting and analyzing data on workers and the environment. Through a field demonstration conducted in a Korean tunnel construction site, we validated the effectiveness of the proposed system, which demonstrated real-time monitoring of workers and reliable communication capabilities, leading to improved safety and cost-efficiency in tunnel construction. By implementing the proposed system, we achieved a significant reduction of 37% in monthly construction costs and 77% in annual construction costs compared to conventional methods.

To facilitate the promotion and application of the whole process engineering consulting (WPEC) model, the transmission mechanism of influencing factors in WPEC's promotion and application is investigated. It identifies and categorizes the influencing factors within the framework of "external environment-project factors-stakeholders", systematically organizing and summarizing ten primary categories and thirty-eight secondary influencing factors of WPEC's promotion and ap-plication. Utilizing the complex network analysis method, a network of influencing factors in the promotion and application of WPEC is constructed. The network is then converted into three binary networks based on weight, which are subjected to structural analysis and motif analysis. On this basis, the transmission mechanism of influencing factors in WPEC's promotion and applica-tion and its causations are explored.

A pump station is a very important flood control facility for mitigating inundation of urban lowland areas. It is not easy to secure a site to increase the capacity of a pump station in an urban area because of various limitations or to maximize the discharge capacity of the pump sump. Adding a facility to improve the pump capacity of a pump station may affect the flow characteristics, such as unexpected increases in the flow velocity and vorticity, and cause severe problems with operating the pump station. To solve those problems, anti-vortex devices (AVDs) have been developed and adopted for appropriate design standards. The Korean design criteria for AVDs are based on experience and foreign standards because not enough data on the AVD are available. In this study, the flow in the sump was numerically simulated at various AVD heights to collect information on improving the design and efficiency of a pump station. Consequently, an appropriate height for the AVD and changes in the flow pattern and vortex in the pump sump were determined and compared with 12 cases of inflow conditions with respect to the vertical location.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Effective waste elimination is critical for the success of construction projects. Although several studies have focused on various aspects of construction waste, limited efforts have investigated the dynamic effect of Making-Do (MD) practices on productivity, rework, defects, and materials wastage. From a lean construction perspective, this study aims to address MD waste using the Last Planner System (LPS) and BIM. First, the casual structure that can cause MD in construction projects was expressed in a casual loop diagram (CLD), and thematic analysis uncovered the strategies of LPS-BIM to eliminate MD identified by reviewing the literature. Secondly, twenty-five strategies from the LPS and BIM strategies to address MD using Structural Equation Modeling (SEM) were assessed. Subsequently, a system dynamics model (SDM) for investigating LPS-BIM strategies on MD decisions in a construction project was formulated based on the underlying causal loop diagrams and the mathematical relations among the variables. Finally, the model was applied to three projects, and simulations for four LPS-BIM scenarios were carried out. The findings show that dynamic interactions among diverse production planning and control factors are critical in evaluating MD impacts on a construction project. The results demonstrate that the LPS-BIM approach resulted in an average 43.8% reduction in the tasks performed with MD, 45.3% of constraints, 66.5% of construction waste, increasing 13.7% completion rate, and 29.3% cost reduction, demonstrating that LPS-BIM as a more efficient solution for MD mitigation and construction planning.

High-spin states of 192Tl are populated by the heavy ion fusion-evaporation reaction 181Ta(16O, 5n)192Tl at 97 MeV beam energy. A new level scheme with eight new levels is constructed and the level spins are tentatively assigned. The negative-parity yrast band is extended up to 23^{-}\hbar. Subsequently, the systematics of signature splitting and signature inversion are discussed for the negative-parity yrast band of odd-odd Tl isotopes including 192Tl, 194Tl, 196Tl, and 198Tl. With the increase of neutron number signature inversion is found in 196,198Tl at high-spin state in these four Tl isotopes. The reason may be due to the competition between neutron-proton interaction and Coriolis force.

Tunnel fires are generally detected using various sensors, including measuring temperature, CO concentration, and smoke concentration. To address the ambiguity and inconsistency in multi-sensor data, this paper proposes a tunnel fire detection method based on an improved Dempster-Shafer (DS) evidence theory for multi-sensor data fusion. To solve the problem of evidence conflict in DS theory, a two-level multi-sensor data fusion framework is adopted. The first level of fusion involves feature fusion of the same type of sensor data, removing ambiguous data to obtain characteristic data, and calculating the basic probability assignment (BPA) function through the feature interval. The second level fusion derives basic probability numbers from the BPA, calculates the degree of evidence conflict, normalizes to obtain the relative conflict degree, and optimizes the BPA using the trust coefficient. The classical DS evidence theory is then used to integrate and obtain the probability of tunnel fire occurrence. Different heat release rates, tunnel wind speeds, and fire locations are set, forming four fire scenarios. Sensor monitoring data under each simulation condition are extracted and fused using the improved DS evidence theory. The results show that the proposed improved DS evidence theory method detects the probability of fire occurrence in the four scenarios as 67.5%, 71.0%, 82.8%, and 83.5%, respectively, and identifies fire occurrence in approximately 2.4 seconds, an improvement of 64.7% to 70% over traditional methods. This demonstrates the feasibility and superiority of the proposed method, highlighting its significant importance in ensuring personnel safety.

The magnetic properties of 0.10 mm ultra-thin grain-oriented (UTGO) silicon steel and Fe-based amorphous (FBA) alloy under sinusoidal excitation were measured experimentally, and the magnetic field strength and iron loss of the two materials under different frequencies and magnetic densities were obtained. Based on the measured data, the magnetization and loss characteristics of the two materials were analyzed and compared. Furthermore, two Epstein square ring models of the same specification and different materials were designed, and the reliability of the models was verified. Then, the electromagnetic characteristics of the two Epstein square ring models at higher and lower frequencies were calculated by using the finite element method, and the iron loss was obtained and compared. The results show that the FBA alloy has good application characteristics at low frequency and low power, and the 0.10 mm UTGO silicon steel has good application characteristics at high frequency and high power. This research can provide important data basis to promote the application of these two materials in new energy equipment.

In recent years, the demand for natural and synthetic zeolites has surged due to their distinctive properties and myriad industrial applications. This research aims to synthesise crystalline zeolites by co-recycling two industrial wastes: salt slag (SS) and rice husk ash (RHA). Salt slag, a problem-atic by-product of secondary aluminium smelting, is classified as hazardous waste due to its reac-tive and leachable nature, though it is rich in aluminium. Conversely, RHA, an abundant and cost-effective by-product of the agro-food sector, boasts a high silicon content. These wastes were utilised as aluminium and silicon sources for synthesising various zeolites. The study examined the effects of temperature, ageing time, and sodium concentration on the formation of different zeolite phases and their crystallinity. Results indicated that increased Na+ concentration favoured SOD zeolite formation, whereas LTA-type zeolite formation was promoted at higher temperatures and extended ageing times. The formation range of the different zeolites was defined and supported by a crystallographic, microstructural, and morphological analysis. Additionally, the thermal be-haviour of the zeolites was investigated. This work underscores the potential to transform indus-trial waste, including hazardous materials like salt slag, into sustainable, high-value materials, fostering efficient waste co-recycling and promoting clean, sustainable industrial production through cross-sectoral industrial symbiosis.

The article presents the results of research work devoted to improving the characteristics of paint and varnish coatings based on aqueous dispersions of polyacrylates, it is proposed to modify them by introducing mineral raw materials as fillers and hydrated lime with subsequent processing in a vortex layer apparatus. Introduction of activated diatomite does not cause deterioration of covering power, adhesion and increase of porosity of the paint material. Modification of coatings contributes to the increase of their operational properties, which can be associated with the reduction of free volume in the composite, formation of polymer boundary layers with modified physical and chemical properties. The aim of the study is to obtain water-dispersion paint and varnish composition containing modified diatomite on polyacrylate basis and subsequent study of the main physical and mechanical parameters. The work has been carried out by the following method: determination of porosity, adhesion, elasticity, covering power of the control composition; determination of porosity, adhesion, elasticity, and covering power of the obtained composites using modified filler; investigation of the influence of radiation in the infrared spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of research works it was noticed that modification of water dispersions with silica activated diatomite helps to eliminate the main disadvantages of materials and coatings based on acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate base does not lead to deterioration of the main performance characteristics of paint coatings - porosity, adhesion, elasticity and covering.

The collapsible loess will rapidly soften and lose its bearing capacity when soaked in water. Under a mild condition (20°C), the biomimetic inorganic agent, Diammonium phosphate (DAP), reacts with calcite in the collapsible loess, producing a stronger bonding material, hydroxyapatite (HAP), to modify and stabilize the soil. Uniaxial compression, permeability tests and morphological analysis using XRD and SEM/EDX microscopy were carried out to assess the effectiveness of DAP stabilization on the collapsible loess. The results indicated that HAP improved the inter-particle bonding within loess, filled the pores within particles, reduced the permeability, and consequently mitigated collapsibility of loess. The compressive strength of DAP-treated loess increased as DAP concentration increased. Following 28-days curing, the compressive strength of the loess treated with a 3.0 mol/L DAP solution was six times greater than that of the untreated group. DAP's reinforcement effect on loess was superior to that of cement. The compressive strength of DAP-treated loess was about double that of cement-treated loess and the permeability coefficient was reduced by more than 50% at equivalent solid content. Furthermore, DAP generated 68% fewer carbon emissions compared to Portland cement. Considering eco-friendly and sustainable development, DAP offers a more competitive alternative for modification and stabilization of loess.

Most astrophysicists today believe that the present universe was produced in a big bang. This article explores the big cycle of matter and energy in the universe, with the big bang as an important part of the cycle.The authors approve of the idea that the universe is gravitationally closed. That is, its average density is higher than the critical value. All the matter and radiation cannot fly out the closed universe.The 3k background radiation is a vast heat ocean in the closed universe, stable and eternal. It is not the afterglow of the thermal radiation of the decoupled fire ball, 380,000 years after the big bang, as many people believed so far. The big bang and the following big expansion drove the matter of more than 2×10¹² galaxies to the remote space. Their potential energies become higher and higher, while their huge kinetic energies that they derived from the big bang become smaller and smaller until drop down to zero. The galaxies will then return back one after another, passing the central region of the universe with tremendously great kinetic energies. They of course cannot all return back directly to their start point of the big bang and restore to the state of the original cosmic core. They will rush to pass the central region and fly to the other sides of the universe, and shuttle around the central part ceaselessly. From the big bang to the following expansion, to the numerous galaxies, to the more than 2×10²³ stars, and to the stars releasing huge nuclear energy due to their internal nuclear fusion each for about 10¹⁰ years, all these enormous processes are irreversible, resulting in enormous increase in entropy. These processes produce large amount of light and other radiations and pour them into the extremely vast heat ocean. These light and other radiations will also be shuttling ceaselessly in the vast heat ocean until, by their interaction with the rare dusts in the galaxies, they mingle into the 3K thermal radiation of the heat ocean. In all the galaxies, there are various black holes. Every black hole, since its birth, ceaselessly extracts the matter and radiation that approach it, and gets larger. In the above mentioned shuttling of all the galaxies, numerous stars and black holes in these galaxies have many chances to approach even meet each other. A black hole can annex other celestial bodies that it meets, including annex other black holes. All these processes carry on and on ceaselessly, resulting in the matter of these celestial bodies to concentrate again and again. The number of all the celestial bodies including the black holes reduces ceaselessly, and the mass of the survived black holes become larger, and their shuttling amplitudes become shorter. The larger black holes and the shorter amplitudes result in the rate of concentration of mass to be faster. Eventually, all the matter in the universe will be concentrated to form a tremendously large central black hole. The central black hole has an astonishingly large Schwarzschild sphere, absorbing the thermal radiation from the vast heat ocean very rapidly and ceaselessly until some threshold value of its internal energy is exceeded, and a new big bang breaks out. The black holes provide a way in the Universe to re-concentrate matter and energy again. Black holes are Maxwell’s demons in the Nature.

The domain of construction engineering and management is evolving rapidly. Optimizing resource positioning is crucial for meeting the challenges of efficiency and productivity. This research presents a novel methodology that incorporates Agent-Based Modeling (ABM), Building Information Modeling (BIM), and Bluetooth Low Energy (BLE) technologies, augmented with a Client Early Warning System (CEWS) and a Decision Support System (DSS). What makes this study unique is that it provides a real-time methodology for resource allocation and project management, tailored to address the complexities of modern construction projects. The application of this integrated technological framework marks a significant leap in construction management, empowering data-driven decision-making and significantly improving project efficiency. Empirically validated through a case study at Helwan University's College of Engineering and substantiated by expert surveys, this research showcases a transformative model for resource management. The findings not only underscore the practical applicability of this approach but also open new horizons for its adoption in global construction practices, offering insights for future research endeavors focused on expanding these methodologies to a wider range of resources.

This study evaluates the efficiency of biodegradable polyurethane foams as thermal insulation materials compared to conventional materials like expanded polystyrene (EPS). Key parameters analyzed include thermal conductivity, energy savings, CO2 emission reductions, and investment payback periods. Biodegradable polyurethane foams demonstrated a thermal conductivity of 0.022 W/(m·K), significantly lower than EPS's 0.035 W/(m·K), leading to higher energy savings. Calculations reveal an annual energy saving of 443,820 kWh for polyurethane foams, compared to 441,330 kWh for EPS. Financially, polyurethane foams save approximately €53,258.4 annually, while EPS saves €52,959.6. In terms of environmental impact, polyurethane foams reduce CO2 emissions by 88,764 kg annually, versus 88,266 kg for EPS. Despite the higher initial cost of polyurethane foams (€50/m² compared to €30/m² for EPS), the payback period is remarkably short at 0.094 years (1.13 months) compared to EPS's 0.057 years (0.68 months). These findings highlight biodegradable polyurethane foams as a superior option for thermal insulation, offering significant energy, financial, and environmental benefits.

Cool roofs are roofing systems designed to reflect significant solar radiation, reducing heat absorption and subsequent cooling energy demands in buildings. This paper provides a comprehensive review of cool roof technologies, covering performance standards, material options, energy-saving potential, and hygrothermal considerations. The review examines provisions in current codes and standards, which specify minimum requirements for solar reflectance, thermal emittance, and solar reflectance index (SRI) values. These criteria often vary based on factors like roof slope, climate zone, and building type. Different cool roof materials are explored, including reflective paints and coatings that can be applied to existing roofs as cost-effective solutions. Several studies demonstrated the energy performance benefits of cool roofs, showing significant reductions in cooling loads, indoor air temperatures, peak cooling demand, and overall cooling energy consumption compared to traditional roofs. However, hygrothermal performance must be evaluated, especially in cold climates, to optimize insulation levels and avoid moisture accumulation risks, as reduced heat absorption can alter moisture migration patterns within the building envelope. While cool roofs provide substantial energy savings in hot climates, further research is needed to validate modeling approaches against real-world studies, investigate the impact of seasonality and green spaces on cool roof efficacy and urban heat island mitigation, and explore energy savings potential, moisture control, and condensation risks in cold and humid environments.

This study is dedicated to understanding and simulating the mechanical properties of concrete, with a specific focus on the mesoscopic scale. Investigating concrete at this level involves examining its composition as a heterogeneous amalgamation comprising mortar, aggregates, and the interfacial transition zone (ITZ). Such an approach provides a detailed examination of the material's behavior and attributes. Numerical models are utilized, leveraging the finite element method (FEM), to examine the behavior of concrete. The study employs MATLAB programming to develop three-dimensional models, subsequently subjected to FEM analysis. Various mesoscopic Representative Volume Elements (RVEs) are formulated, encompassing varied shapes and dimensions. The MATLAB framework generates input files for numerical FEM simulations, replicating compression strength tests. As complexity increases with the inclusion of the ITZ, prismatic RVEs are developed. The proposed mesoscopic model establishes a foundational framework for a numerical simulation methodology tailored to laboratory compression tests. It provides detailed insights into concrete behavior, elucidating deformation, and fracture mechanisms. Although not a complete substitute for experimental methods, these models offer a cost-effective and expeditious alternative, pinpointing vulnerable areas and exploring the implications of additional materials on concrete behavior. Experimental data and virtual tests pave the way for mitigating carbon footprint and improving concrete sustainability.

Western countries are experiencing an increasing aging population, resulting in heightened disability and mobility issues. This trend is expected to escalate in the coming decades. Therefore, ensuring adequate accessibility in collective residential housing –where individuals spend much of their daily lives– is of paramount importance. This paper presents a case study focused on the accessibility of building entrances in collective residential housing in Southeast Spain, specifically in the Region of Murcia. In this region, 9.8% of the population has disabilities, and 15.75% were over 64 years old in 2020. The study began by compiling the relevant national and regional accessibility regulations for existing buildings. Subsequently, extensive fieldwork was conducted, analyzing 150 collective residential housing buildings. Based on this analysis, a set of recommendations to enhance accessibility was formulated for buildings not complying with the regulations. The results are presented and discussed in detail. The most frequent recommendation was the construction of accessible ramps, identified as the primary solution in over 40% of cases, either alone or in conjunction with other measures. In 54% of the cases, multiple interventions were necessary to achieve effective accessibility adaptation. The findings of this study could inform the development of public policies aimed at improving accessibility conditions in urban areas.

This paper analyses the application of deep learning techniques for predicting wave overtopping events in port environments using sea state and weather forecasts as inputs. The study was conducted in the outer port of Punta Langosteira, A Coruña, Spain. A video recording infrastructure was installed to monitor overtopping events from 2015 to 2022, identifying 3709 overtopping events. The data collected was merged with actual and predicted data for the sea state and weather conditions during the overtopping events, creating three datasets. We used these datasets to create several machine learning models to predict whether an overtopping event would occur based on sea state and weather conditions. The final models achieved a high accuracy level during the training and testing stages: 0.81, 0.73, and 0.84 average accuracy during training and 0.67, 0.48, and 0.86 average accuracy during testing, respectively. The results of this study have significant implications for port safety and efficiency, as wave overtopping events can cause disruptions and potential damage. Using deep learning techniques for overtopping prediction can help port managers take preventative measures and optimize operations, ultimately improving safety and helping to minimize the economic impact that overtopping events have on the port's activities.

When profit-driven renewal is difficult to implement, many historic districts are “frozen protected” in China. In the social context of “building cities for the people” in recent years, the public value-oriented renewal of urban historic areas plays an important role in the transformation of cities. This study investigates the strategies of historic district regeneration in China by integrating spatial form, urban governance, and public value. We propose a novel framework to analyze the regeneration of historic districts, using Taiyuan Bell Tower Street as a case study. The framework distinguishes between two dimensions: spatial and economic-social. In the spatial dimension, we focus on the transformation of spatial form to regenerate public value, emphasizing the attribute of "publicness" as central to urban regeneration efforts. This involves a tiered approach of excavating and upgrading historic districts at macro, meso, and micro levels. In the economic-social dimension, we explore urban governance to strengthen public value, involving government, market, and societal actors in a collaborative renewal process. The analysis highlights that a public value-oriented approach to heritage regeneration offers greater sustainability and could serve as a model for other cities seeking similar outcomes.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

The article presents the results of research work devoted to the study of composite materials on polymer binder with the content of modified mineral filler - water-dispersion paint and varnish materials on acrylic polymer with modified filler - diatomite. The aim of the study is to obtain polymer-based composites with modified diatomite (water-dispersion paint on acrylic binder) with improved performance properties. Methods: determination of porosity, adhesion, elasticity, hiding power of the control composition; determination of porosity, adhesion, elasticity, hiding power of the obtained composites with the use of modified filler; investigation of the influence of radiation in the infrared radiation (IR) region of the spectrum of the paint coating surface using FLIRB620 thermal imager. As a result of work it is noticed that modification of water dispersions by silica activated diatomite promotes elimination of the main disadvantages of materials and coatings on the basis of acrylate binder - low water resistance and low physical and mechanical characteristics, introduction of modified diatomite into water emulsion paint on acrylate basis does not lead to deterioration of the main operational characteristics of paint and varnish coatings - porosity, adhesion, elasticity and covering. When analyzing the effect of emissivity in the IR region of the spectrum of the paint coating surface, a significant effect of the quantitative content of modified diatomite on the reduction of emissivity of paint coatings in the IR region of the spectrum was established and it was shown that a significant effect of the reduction of emissivity of paint coatings in the IR region of the spectrum is provided by the introduction of modified diatomite in the amount of 40 wt.h. into the mixture. The influence of the time of full-scale tests in the investigated small range regardless of the quantitative composition of modified diatomite on the performance characteristics of the paintwork was established.

The imperative to achieve carbon neutrality has driven significant advancements in the construction sector, particularly in the production and utilization of building materials. This paper explores innovative strategies and practices designed to reduce the carbon footprint of construction materials, with a focus on both the production processes and the application of sustainable materials. Key innovations include the development of low-carbon and carbon-negative materials, the integration of renewable energy sources in production, and the implementation of advanced recycling technologies. Case studies of successful projects demonstrate how these strategies can be applied in real-world scenarios, highlighting both the benefits and challenges encountered. The analysis also delves into the technical and economic aspects of these innovations, addressing the barriers to their widespread adoption and proposing solutions to overcome these challenges. Through a comprehensive examination of current practices and future trends, this paper aims to provide a roadmap for the construction industry to achieve carbon neutrality, contributing to broader climate change mitigation efforts and fostering a more sustainable built environment.

Productivity has been modest in construction due to many reasons, especially project-specific operations and fragmentation. The main aim of this research is to map the challenges towards industrialization in construction through a comparative study of the manufacturing industry. An inductive approach and a qualitative method are followed by applying semi-structured inter-views, and node-based thematic analysis. The key elements of industrialization in mature man-ufacturing companies are benchmarked. The findings indicate a specific order of steps for indus-trialization in construction. Data and information management with achieved systematization have been sources of productivity in manufacturing companies. However, the systematization starts from the offering, construction companies need to define their offering, that is the products, and define their respective data. Only accurate and good quality data on products enables the systematization of order delivery processes, which are the engine for a company’s success or failure. Continuous efficiency improvement is only possible with systematized processes and respective data related to the processes. The originality involves clarifying the industrialization of construction companies via products, respective data, and processes considering industrialized manufacturing companies.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

Agriculture contributes towards South African economy, but this sector is highly vulnerable to risks imposed by climate change. Smallholder maize farmers are specifically susceptible to climate change impacts. Maize crop plays a crucial role in the country's food security as it is considered a stable food for households and source of feed for livestock. The study aimed to analyze the socio-economic factors influencing smallholder maize farmers’ willingness to adopt climate-smart agriculture. It was conducted in three different areas due to their specific agro-ecological zones. Multipurpose research design was used to gather data, and multistage random sampling to choose the study areas. Subsequently, 209 purposively selected farmers were interviewed face-to-face using structured questionnaires and focus discussion groups. Descriptive statistics and Double-hurdle regression model were used to analyze the data. Descriptive results indicated that 81%, 67%, and 63% farmers were willing to adopt CSA in Ga-Makanye, Gabaza, and Giyani, respectively. Empirical results from the first and second hurdles of the regression analysis showed that farmers’ education, crop diversification, information about CSA positively influenced the decision to adopt CSA while household size and agricultural experience negatively influenced the decision to adopt CSA. It is recommended that the Department of Agriculture, Land Reform, and Rural Development should provide CSA workshops and educational programs to farmers to enhance their knowledge and decision-making processes regarding adaptation strategies.

This paper discusses the design and implementation of a portable IoT station. Communication and data synchronization issues in several installations are addressed here, making possible a detailed analysis of the entire system during its operation. The system proposed is interpreted as an additional tool which can be utilized in several applications, where the system operator requires a synchronized data stream, combining multiple communication protocols into one single time stamp. The hardware selected for the portable IoT station complies with the International Electrotechnical Commission (IEC) industrial standards. A short discussion regarding interface customization shows how easily the hardware can be modified so that it is integrated with almost any system. A Programmable Logic Controller enables the Node-Red to be utilized. This open-source programming tool employs flows to define operations for each global variable nominated in the Modbus register. Two applications are presented and discussed in this paper, each application has a distinct methodology utilized to publish and visualize the acquired data. The portable IoT Station is highly customizable, consisting of a modular structure and providing the best platform for future research and development of dedicated algorithms.

The field of construction materials is pivotal in developing sustainable and resilient infrastructure. This demands continuous research to understand the properties and behaviors of these materials under diverse conditions. Although advancements in material science and numerical modeling have been significant, experimental testing remains indispensable for a thorough comprehension of material characteristics, particularly under extreme stresses and environmental factors. This need has forced the development of a wide array of testing techniques, each designed to evaluate specific engineering properties, thus creating a complex and varied landscape of experimental methodologies. This study provides a comprehensive overview of both conventional and innovative experimental testing techniques used to characterize construction materials. It explores the related methodologies and identifies potential gaps in their application within the industry. The spectrum of testing covered includes mechanical, chemical, thermal, microstructural, durability, physical, rheological properties, and non-destructive testing methods. Mechanical tests assess strength, hardness, and fatigue, whereas chemical analyses utilize techniques such as spectroscopy and chromatography. Thermal properties are examined using thermogravimetric analysis, and microstructural characteristics are explored through advanced imaging techniques. Durability testing focuses on materials’ resistance to environmental challenges, while physical properties tests evaluate aspects like porosity and water absorption. Rheological and non-destructive tests further examine materials’ behavior and integrity without causing damage. By discussing these methodologies, the study sheds light on various approaches to material evaluation and aims to enhance the selection, application, and development of testing standards. This overview seeks to inform and inspire future research and innovation in the science of construction materials, contributing to the development of more resilient and sustainable construction practices.

Large-span post-tensioned (PT) beams play a crucial role in maximizing the benefits of post-tensioning techniques. Bonded and unbonded systems are prevalent, with the latter being more widespread in the United States. While bonded systems are advantageous for creating long spans when multiple tendons are grouped in ducts, limited literature exists on their demolition. In a case study, this paper addresses the unique challenge of demolishing large-span bonded post-tensioned beams due to a building's functional change. Emphasizing insights for engineers, it explores the use of cutting and dismantling methods, considering the presence of prestressed cables. The demolition process is distinctive due to the presence of numerous pre-stressed cables along the beams, necessitating a specialized and cautious cutting approach. This is accomplished through the use of a drilling technique that selectively distresses the tendons, ensuring they are not all affected simultaneously. An intriguing observation discussed in this paper pertains to the occurrence of horizontal cracks accompanied by loud sounds following the drilling process, offering insights from the design perspective of PT systems. The paper details an innovative method for safely demolishing large-span bonded PT beams, using ground-penetrating radar and computer models to navigate structural complexities and ensure nearby structures' safety.

This research proposes a methodology for minimizing losses in transmission lines (LT), considering the reconfiguration of the architecture of the electrical power system (SEP). The implementation of this methodology redirects the power flow with optimal switching through its LTs to guarantee the stability of the voltage, angle, frequency, and power balance to minimize losses that affect the reliability and quality of the system. Optimal transmission switching (OTS) allows various types of analysis to be carried out, where the loadability of the lines, response times, and operating costs, among others, can be improved. This article proposes to minimize the losses in the transmission lines with the OTS by using AC power flows as a mixed integer nonlinear problem (MINLP). Several test scenarios evaluate the method’s effectiveness, determining the optimal topology for corrective control that optimizes power flows in different situations. It has been proven that this approach reduces losses compared to a base case by 99%, even in the face of N-1 or random contingencies, without losing load, maintaining the same active power dispatch, and finally verifying a strategic increase in dispatch of reactive power to maintain operating parameters within stable limits.

This study primarily investigates the effect of fly ash (FA) content on the mechanical properties and hydration performance of alkali-activated ground granulated blast furnace slag cements (AAGC), and compares the related properties with ordinary Portland cement (OPC). Additionally, the study examined the hydration products, thermal analysis, MIP, SEM, chemically bound water, and pH values of AAGC. The compressive strength of AAGC showed a retrogression phenomenon from 3 to 28 days, with the 14-day and 28-day compressive strengths of AAGC being higher than those of OPC. The AAGC with 20% FA content exhibits the highest 28-day compressive strength (75 MPa). The hydration heat release rate curved of OPC and AAGC can be divided into the initial induction period, induction period, acceleration period, deceleration period and steady period. As FA content increases, the 28-day pore volume of AAGC increased while pH values and chemically bound water decrease. SEM images of AAGC with low FA content showed more microcracks.

In order to help the transportation industry achieve the goal of carbon peak and carbon neutrality, this study is based on the selection of eight variables, such as population size, per ca pita GDP, personal vehicle ownership, passenger and freight turnover, and green space coverage, as the factors influencing the carbon emissions of the transportation industry in Jiangsu Province, and the prediction and analysis of the transportation carbon emission trends from 2000 to 2021, and the prediction and analysis of the carbon emissions of the transportation industry and the time of the peak of the carbon emissions in Jiangsu Province. The trend of transportation carbon emissions from 2000 to 2021 was predicted and analyzed, and the carbon emissions and peak time of carbon emissions in the transportation industry in Jiangsu Province were predicted and analyzed. Comparing the predicted results with other models to verify the accuracy of the results, it was found that the WOA-SVM model had the smallest error among several models. On this basis, targeted measures are proposed to accelerate the process of carbon peak and ensure the smooth achievement of carbon neutrality goals in Jiangsu Province. The results indicate that under the current policy measures, the peak carbon emissions in Jiangsu Province will occur in 2038, with a peak of 48.72 million tons. Jiangsu Province should actively adopt energy-saving and emission-reduction measures, build a green and low-carbon transportation development model, and achieve the carbon peak target ahead of schedule.

This paper evaluates norms and assesses the level of knowledge in air conditioning project management within the construction industry. A total of 25 questions were distributed to multiple candidates, who were filtered based on pre-established inclusion and exclusion criteria. Thirty-nine candidates were ultimately approved to participate in the survey. The questions were designed to address five hypotheses, with each set of five questions corresponding to one hypothesis. The results were obtained after pre-processing the data using Matlab software. The data was pre-processed using Matlab software, and the results were analyzed using the Delphi method. The analysis revealed that only two hypotheses were approved: No matter whether there are nationalized safety rules or not, the impact of data sciences and smart technologies, including air conditioning management systems, is critical for human life in the building business.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

The severe climate changes due to global warming pushed the world to strive to reduce carbon emissions. This study aims to minimize the carbon emissions for a proposed smart energy hub. This paper prioritizes the minimization of carbon emissions, taking into consideration the minimization of operation running costs, and the maximization of profit. In this paper two optimization scenarios were studied, to compare the results. In the first scenario, the minimization of carbon emissions was achieved, in the second scenario, the minimization of running costs and maximization of profit from the hub assets were studied. The proposed model was designed in MATLAB. Then the results were verified by CPLEX and validated by RTDS. The multi-objective model was presented to obtain the optimal operation. The mitigation of data uncertainty was achieved by applying the Kalman filter. In this work, a novel method was proposed for the estimation of the quarter-hour resolution data from the hourly one via the Kalman filter rather than applying the classic polynomial interpolation methods.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

The distribution of tiny sensors over a specific area was first proposed in the late 1990s as a concept known as Smart Dust. Several efforts focused primarily on computing and networking capabilities but quickly ran into problems related to power supply, cost, data transmission, and environmental pollution. To overcome these limitations, we propose using paper-based (confetti-like) chemosensors that exploit the inherent selectivity of chemical reagents, such as colorimetric indicators. In this work, cheap and biodegradable passive sensors made from cellulose could successfully indicate the presence of hazardous chemicals, e.g., strong acids, by a significant color change. A conventional color digital camera attached to a drone could easily detect this from a safe distance. The collected data was processed to define the hazardous area. Our work presents a combination of the smart dust concept, chemosensing, paper-based sensor technology, and low-cost drones for flexible, sensitive, economical, and rapid detection of hazardous chemicals in high-risk scenarios.

This manuscript offers a concise overview of paper microfluidics, emphasizing its sustainable sensing applications in healthcare, environmental monitoring, and food safety. Researchers have developed innovative sensing platforms for detecting pathogens, pollutants, and contaminants by leveraging the paper’s unique properties, such as biodegradability and affordability. These portable, low-cost sensors facilitate rapid diagnostics and on-site analysis, making them invaluable tools for resource-limited settings. The review discusses fabrication techniques, principles, and applications of paper microfluidics, showcasing its potential to address pressing challenges and enhance human health and environmental sustainability.

In California, water is a perennial concern. As competition for water resources increases due to growth in population, California’s tree nut farmers are committed to improving the efficiency of water used for food production. There is an imminent need to have reliable methods that provide information about the temporal and spatial variability of crop water requirements, which allow farmers to make irrigation decisions at field scale. This study focuses on estimating the actual evapotranspiration and crop coefficients of an almond and pistachio orchard located in Central Valley (California) during an entire growing season by combining a simple crop evapotranspiration model with remote sensing data. A dataset of the vegetation index NDVI derived from Landsat-8 was used to facilitate the estimation of the basal crop coefficient (Kcb), or potential crop water use. The soil water evaporation coefficient (Ke) was measured from microlysimeters. The water stress coefficient (Ks) was derived from airborne remotely sensed canopy thermal-based methods, using seasonal regressions between the crop water stress index (CWSI) and stem water potential (Ystem). These regressions were statistically-significant for both crops, indicating clear seasonal differences in pistachios, but not in almonds. In almonds, the estimated maximum Kcb values ranged between 1.05 to 0.90, while for pistachios, it ranged between 0.89 to 0.80. The model indicated a difference of 97 mm in transpiration over the season between both crops. Soil evaporation accounted for an average of 16% and 13% of the total actual evapotranspiration for almonds and pistachios, respectively. Verification of the model-based daily crop evapotranspiration estimates was done using eddy-covariance and surface renewal data collected in the same orchards, yielding an r² >= 0.7 and average root mean square errors (RMSE) of 0.74 and 0.91 mm day^-1 for almond and pistachio, respectively. It is concluded that the combination of crop evapotranspiration models with remotely-sensed data is helpful for upscaling irrigation information from plant to field scale and thus may be used by farmers for making day-to-day irrigation management decisions.

This study aimed to identify miRNA editing sites during adipose tissue development in Ningxiang pigs and analyze their characteristics and functions. Based on the small RNA-seq data from subcutaneous adipose tissue samples of Ningxiang pigs at four stages (30, 90, 150 and 210 days), we constructed a developmental atlas of the miRNA editome in adipose tissue of Ningxiang pigs. The characteristics and functions of this editome were further explored through bioinformatics analysis. The findings revealed that a total of 505 miRNA editing sites were identified with C-to-U editing types being the most prevalent, followed by U-to-C, A-to-G and G-to-U. Importantly, these four types of miRNA editing exhibited a base preference. The number of editing sites showed obvious differences among age groups, with the highest occurrence of miRNA editing events observed at 90 days of age and the lowest at 150 days of age. In the miRNA seed region, a total of 9 miRNA editing sites were identified with significant differences in editing levels (P < 0.05), and located in ssc-miR-23a, ssc-miR-27a, ssc-miR-30b-5p, ssc-miR-15a, ssc-miR-497, ssc-miR-15b, and ssc-miR-425-5p, respectively. Target gene prediction and enrichment analysis revealed that the editing of miR-497 may potentially regulate fat deposition by inhibiting adipose synthesis via influencing target binding. These results provide new insights into the regulatory mechanism of pig fat deposition.

This article summarizes the results of a research conducted to create an intelligent platform supporting small farmers growing vegetables. In Bulgaria, many farmers use relatively small areas for their production. Considering this situation, the platform is designed for regional use, trying to make maximum use of the specific climatic features of the monitored microdistrict. Consequently, special attention is paid to the possibilities of adapting the platform to the specific environment in which the observed plants grow. Thus, the platform is implemented as an agent-oriented system providing needed flexibility. The core of the platform is a personal assistant, which is responsible for tracking the vegetation cycle of the monitored crop and, upon detection of anomalies, preparing warnings to the farmer. The general architecture of the platform is also presented. In a distributed knowledge base, agriculture-specific knowledge are stored. Furthermore, a standardized interface for receiving data from the sensor networks located in the production areas is briefly described. Currently, the platform is being tested for monitoring four varieties of tomatoes grown on the territory of the national research center for potato breeding. Special attention is paid to the measurements carried out. Conclusions have been drawn that will help improve the platform.

Access to reliable water supply is critical for sustainable development and public health, yet many peri-urban and rural communities in the developing world face challenges such as poor maintenance, faulty infrastructure, and inadequate governance of water services, hindering the UN’s Sustainable Development Goals (SDG). In Emina-Boadi, a small town in Kumasi, Ghana, residents increasingly rely on boreholes due to substandard service from the Ghana Water Company Limited (GWCL). This shift highlights concerns about water reliability, quality, and affordability, impacting public health and hindering progress toward SDG 6. This case study assesses water service levels using key performance indicators (KPIs) such as quantity, quality, affordability, accessibility, and reliability, focusing on sources like boreholes, hand pumps, piped water, hand-dug wells, rainwater, and surface waters. The study aims to delineate the roles of different water providers, understand community dynamics, and evaluate contributions to rural development and SDG 6 through stakeholder interviews and questionnaires. Leveraging the WASHCost framework, which aims to improve planning methods and provision of water and sanitation services by addressing the lack of cost information in rural and peri-urban areas, and the Joint Monitoring Programme (JMP) framework, which monitors progress toward global targets related to water, sanitation, and hygiene, the study categorizes indicators and draws connections among them. Findings reveal a significant preference for borehole services, with 87% usage and an 83% reliability rate compared to 13% for GWCL. Daily water consumption averages 60.75 liters per person, with on-premises access improving water collection efficiency to 7 minutes. Dissatisfaction with GWCL services highlights the need for improved delivery aligned with community needs and SDG targets. Adopting sustainable management practices, enhancing infrastructure, and improving governance are crucial for ensuring safe and affordable water access for all residents of Emina-Boadi and similar communities.

Due to the long-term deformation settlement of foundations, issues such as damage and functional failure of buildings and structures have long been of concern in the engineering field. The creep of soil is one of the primary causes leading to long-term deformation of foundations. In this paper, the consolidation deformation, creep characteristics, and creep model of reconstituted saturated silty clay were studied by isotropic compression test and triaxial shear creep test. The results show that for the isotropic compression test, although the applied load adopts different stages of loading, as long as the final applied confining pressure is the same, the number of stages applied by the confining pressure has little effect on the final isotropic consolidation deformation of the sample and the triaxial undrained shear strength after creep. However, for the triaxial shear creep test, it is found that under the same final deviatoric stress, the final deviatoric strain of the sample is closely related to the number of loading stages of deviatoric stress. It shows that the more loading stages of the sample loaded with the same deviatoric stress, the smaller the final deviatoric strain, and the triaxial undrained shear strength of the sample after creep will increase. In addition, it is reasonable to determine the pore pressure dissipation of the sample to 95%((u0-u0)/u0=95%) as the main consolidation end time (tEOP) of the sample. The isotropic consolidation creep curves and the triaxial shear creep curves show certain nonlinearity. Then the logarithmic model and the hyperbolic model were used to fit the creep curves of the samples. It is found that the hyperbolic model has a better fitting effect than the logarithmic model, but for the triaxial shear creep test, the creep parameters of the sample change greatly. Therefore, studying the creep characteristics of soil under different pre-loading steps is of significant engineering importance for evaluating the long-term deformation of underground structures.

In order to foster a more sustainable and eco-friendly trajectory for the construction industry, while concurrently mitigating environmental pollution and energy inefficiency, it is imperative to cultivate an environmentally conscious building and urban environment. Under the background of carbon peak and carbon neutrality, green building evaluation system (GBRS) has become a research hotspot in the field of green building. This paper systematically summarizes the current research progress based on GBRS, focuses on the current weight and indicators setting, analyzes it with Cite Space software, and puts forward its future development direction. The results show that the weight setting method of green building evaluation system is determined by multidimensional and multi-method. From the perspective of environment, society and economy, the scope of indicators setting is expanding. The green building evaluation system will play a guiding role in green building design, and the evaluation process will continue to be optimized and developed in the direction of intelligence and automation.

This study examines the overall needs of the green construction scheme with ‘carbon neutrality’ as the centre in the Zhejiang provincial green development target area. By aggregating and organising the construction and development data of Zhejiang Province, the entropy weight TOPSIS model is formed according to the statistical modelling for quantitative examination of the data, and the scientific assessment scheme of ‘carbon neutrality’ in the regional construction industry of Zhejiang Province is developed. This study aids in completely exhibiting and dynamically understanding the advancement of the ‘carbon neutral’ capacity of the urban construction industry. The objective is to discover the weak link in the advancement of carbon neutrality in several regional construction industries, which is of great relevance for further examining and forecasting the strategic outlook of carbon neutrality and modifying the planning of carbon neutrality strategy in special regional construction industries.

The state-of-the-art smart city has been calling for an economic but efficient energy management over large-scale network, especially for the electric power system. It is a critical issue to monitor, analyze and control electric loads of all users in system. In this paper, we employ the popular computer vision techniques of AI to design a non-intrusive load monitoring method for smart electric energy management. First of all, we utilize both signal transforms (including wavelet transform and discrete Fourier transform) and Gramian Angular Field (GAF) methods to map one-dimensional current signals onto two-dimensional color feature images. Second, we propose to recognize all electric loads from color feature images using a deep neural network with multi-scale feature extraction and attention mechanism. Third, we design our method as a cloud-based, non-intrusive monitoring of all users, thereby saving energy cost during electric power system control. Experimental results on both public and our private datasets have demonstrated our method achieves superior performances than its peers, and thus supports efficient energy management over large-scale Internet of Things.

This paper describes the proposal and development of a proof of concept (PoC) for a data logger system designed for operation and fault detection in bench testing of combustion engines. The main objective was to develop a data logger system that collects data on vibration, sound, temperature, and CO2 levels to identify ignition and combustion faults, thereby contributing to reducing greenhouse gas emissions (GHG). The paper presents (i) the proposal and development and (ii) the open-source code: proof of concept for a data logger system focused on detecting faults and monitoring the operational condition of benchtop combustion engines. The results indicate the feasibility of the PoC for data acquisition and dataset creation for Research and Development purposes.

For the purpose of improve the sustainability of products sold in the EU, Digital Product Passports is a mandatory solution. These passports would systematically gather information about products, such as detailing the materials involved to aid recycling and remanufacturing efforts, or recording the emissions produced throughout the manufacturing process. The overall goal is the establishment of a circular economy in the EU. Current research on Digital Product Passports is focused on collating content for sector-specific applications. However, achieving sustainability goals through Digital Product Passports will require new methods and technical solutions for digital collaboration between supply chain participants, especially in the manufacturing sector. Collaborative work on Digital Product Passports requires trust and traceability in data and access management to ensure privacy over the data contained. One way to enable this securely and confidentially is through the use of blockchain technology, in which stored data cannot be concealed, which is key to the traceability of digital product data documentation. This paper therefore presents a concept for the implementation of generically applicable cross-industry blockchain-based digital product passports. To this end, generic supply chain processes have been abstracted and condensed into the architecture of smart contracts. Great attention is paid to the establishment of traceability as well as privacy through the selection of the blockchain technology Secret Network in combination with Gaia-X functionalities. An illustrative use case for digital product passports in manufacturing is used to demonstrate the applicability of the presented concept. In this use case information about the digital nameplate and carbon footprint is exchanged securely and confidentially in a multi-tenant supply chain network based on the Industry 4.0 infomation model of the Asset Administration Shell.

This paper formulates the performance evaluation of cloud services as a multicriteria group decision making problem, and presents a fuzzy multicriteria group decision making method for evaluating the performance of cloud services. Interval-valued intuitionistic fuzzy numbers are used to model the inherent subjectiveness and imprecision of the performance evaluation process. An effective algorithm is developed based on the technique for order preference by similarity to ideal solution method and the Choquet integral operator for adequately solving the performance evaluation problem. An example is presented to demonstrate the applicability of the proposed fuzzy multicriteria group decision making method for solving the multicriteria group decision making problem in real world situations.

Smart manufacturing encompasses a category of manufacturing that employs computer-integrated capabilities and technologies to enhance supply chain optimization, production efficiency, and recyclability. Yet limited studies have been conducted to optimize these prospects from the perspective of low resource countries where such innovative studies have not been adequately explored. This paper aims to examine the implications of smart manufacturing practices (Smart Procurement, Smart Supply Chain, Smart Production Planning and Control, Automation and Industrial Robot, and Supply Chain Configuration) on pro-environmental behaviour and develop a baseline moderated mediation model to explain the relationship between smart manufacturing and pro-environmental behaviour with a role of green dynamic capability, and environmental orientation. This study is anchored on quantitative research approach, deductive reasoning, and explanatory design. Cross – sectional survey data have been obtained from 382 manufacturing companies in Ghana. Our hypotheses have been tested using Structural Equation Modelling and SMART-PLS version 3.8.9. The study has revealed that smart manufacturing practices significantly and positively relate to pro-environmental behaviour. Moreover, green dynamic capability and environmental orientation moderate the relationship between smart manufacturing and pro-environmental behaviour. The implications of the study include the emergence of a baseline model to guide policymakers, practitioners, and academicians to explain the relationship between smart manufacturing and sustainable manufacturing in the context of developing countries. Again, the social implication of the study includes the realisation of decent job and economic growth, responsible consumption and production as well as actions taken to combat climate change.

This paper describes a system that is used to gather data from Smart Home sensors measuring energy consumption, analyze and predict future consumption by using machine learning algorithm for prediction. It focuses on the architecture of the system as well as the need for such system to exist in practice – why the consumption should be measured at all and how that measurement can be put to good use for achieving energy efficiency.

Matters relating to preservation of environmental resources and climate change, social inclusion and diversity, and open and sound governance have rapidly gained global attention. However, little is known about the construction industry in meeting the environmental, social and governance (ESG) criteria towards sustainable development. In this study, the purpose is to identify the key ESG indicators for construction development. A systematic literature review was undertaken using data from Scopus, PubMed, Google Scholar, JSTOR, ProQuest, and Web of Science. The results show some of the key ESG indicators as climate resilience and green construction activities (at the project level), and active stakeholder engagement and effective project governance (at the firm level) and meeting environmental and social regulation requirements (industry/national level). The limitation of the article is in the sample size of twenty-six journal articles with future expectation of increment as ESG gain more acceptance in the construction industry. This study will be significant for the design of practice framework and policies on ESG in the construction industry. Comprehensively, this study presents relevant ESG indicators for construction management and presents essential information for future research.

Research focused on understanding wider systemic factors driving behavioral change is limited with a dominant focus on the role of individual farmer and psychosocial factors for farming practice change, including reducing fertilizer application in agriculture. Adopting a wider systems perspective, the current study examines change and the role that supporting services have on fertilizer application rate change. A total of 238 sugarcane growers completed surveys reporting on changes in fertilizer application along with factors that may explain behavior change. Logistic regressions and negative binomial count-data regressions were used to examine whether farmers had changed fertilizer application rates and if they had, how long ago they made the change, and to explore the impact of individual and system factors in influencing change. Approximately one in three sugarcane growers surveyed (37%) had changed the method they used to calculate fertilizer application rates for the cane land they owned/managed at some point. Logistic regression results indicated growers were less likely to change the basis for their fertilizer calculation if they regarded maintaining good relationships with other local growers as being extremely important, they had another source of off-farm income, and if they had not attended a government-funded fertilizer management workshop in the five years preceding the survey. Similar drivers promoted early adoption of fertilizer practice change; namely, regarding family traditions and heritage as being unimportant, having sole decision-making authority on farming activities and having attended up to 5 workshops in the five years prior to completing the survey. Results demonstrated the influence of government-funded services to support practice change.

Incorrect sitting posture, characterized by asymmetrical or uneven positioning of the body, often leads to spinal misalignment and muscle tone imbalance. Prolonged maintenance of such postures can adversely impact well-being and contribute to the development of spinal deformities and musculoskeletal disorders. In response, smart-sensing chairs equipped with cutting-edge sensor technologies have been introduced as a viable solution for real-time detection, classification, and monitoring of sitting postures, aiming to mitigate the risk of musculoskeletal disorders and promote overall health. This comprehensive literature review evaluates the current body of research on smart-sensing chairs, with a specific focus on the strategies used for posture detection and classification, as well as the effectiveness of different sensor technologies. A meticulous search across MDPI, IEEE, and Google Scholar databases yielded 34 pertinent studies that utilize non-invasive methods for posture monitoring. The analysis reveals that Force Sensing Resistors (FSR) are the predominant sensors utilized for posture detection, whereas Convolutional Neural Networks (CNN) and Artificial Neural Networks (ANN) are the leading machine learning models for posture classification. However, it was observed that CNNs and ANNs do not outperform traditional statistical models in terms of classification accuracy, due to constrained size and lack of diversity within training datasets. These datasets often fail to comprehensively represent the array of human body shapes and musculoskeletal configurations. Moreover, this review identifies a significant gap in the evaluation of user feedback mechanisms, essential for alerting users to their sitting posture and facilitating corrective adjustments.

Although the field of geomatics has seen multiple technological advances in the recent years which enabled new applications and simplified the consolidated ones, some tasks remain challenging, inefficient, and time- and cost-consuming. This is the case of accurate tridimensional surveys of narrow spaces. Static laser scanning is an accurate and reliable approach but impractical for extensive tunnel environments; portable laser scanning is on the other hand time-effective and efficient but not very reliable without ground control constraints. This paper describes the development process of a novel image-based multi-camera system meant to solve this specific problem: delivering accurate, reliable, and efficient results. The development is illustrated from the system conceptualization and initial investigations to the design choices and requirements for accuracy. The resulted working prototype has been put to the test to verify effectiveness of the proposed approach.

The enormous growth in the penetration of electric vehicles (EVs), has laid the path to advancements in the charging infrastructure. Connectivity between charging stations is an essential prerequisite for future EV adoption to alleviate users’ “range anxiety”. The existing charging stations fail to adopt power provision allocation and scheduling management. To improve the existing charging infrastructure data based on real-time information and availability of reserves at charging stations could be uploaded to the users to help them locate the nearest charging station for an EV. This research article focuses on an a interactive user application developed through SQL and PHP platform to allocate the charging slots based on estimated battery parameters, which uses data communication with charging stations to receive the slot availability information. The proposed server-based real-time forecast charging infrastructure avoids waiting times and its scheduling management efficiently prevents the EV from halting on road due to battery drain out. The proposed model is implemented using a low-cost microcontroller and the system etiquette tested.

There are various modeling techniques adopted for predicting the labor productivity that incorporate the influence of various factors, but neural networks are found to have strong pattern recognition and higher accuracy to get reliable estimates. To develop a construction labor productivity (CLP) model for concreting activities, data were collected through a questionnaire. The most critical influencing parameters were ranked according to their relative importance index (RII). Then the strength of the relationship between CLP and influencing parameters was analyzed using correlation coefficient results generated in Python program. Finally, the CLP model which represents the output of the crew within a certain factor was successfully developed using artificial neural networks (ANNs). Five objectives and six subjective critical influencing parameters were selected using RII. Crew experience, age of workers, and placement technique are the top three influencing parameters that have a strong relation with CLP with correlation coefficient values of 0.5681, 0.5349, and 0.5227 respectively. The developed model within these influencing parameters has a higher capability to predict the output of labor with a 92% coefficient of determination (R2) and a mean squared error of 0.316%. Therefore, the application of such a model for the accurate estimation of labor productivity is recommended.

This study delves into the dynamics of 'Variations' and 'Claims' within construction projects, specifically under the FIDIC-Red Book 1999 (FIDIC 1999) framework. It aims to identify, categorize, and devise mitigation strategies for key types of Variations and Claims, aligning with the FIDIC Conditions of Contract. The research, drawing on inputs from construction industry professionals including Contract Administrators and Project Managers, focuses on the MENA re-gion. This choice is driven by the region's extensive adoption of FIDIC standards and its rapidly growing construction sector. Data collection encompassed a questionnaire distributed to 80 industry experts, predominantly through interviews, focusing on countries like Saudi Arabia, UAE, Kuwait, and Egypt. These locations were chosen to reflect diverse construction practices and the involvement of international firms. Utilizing SPSS-V.25 for statistical analysis, the study uncovers the most prevalent and impactful causes of Variations and Claims, highlighting the critical need for managerial intervention. A key feature of this study is the integration of Scientometric Analysis for a quantitative review of current literature, providing a comprehensive academic context. A significant addition to the methodology is the implementation of a k-means clustering analysis. This advanced statistical technique further classifies the data into distinct clusters, each representing unique combinations of 'Frequency' and 'Impact' of Variations and Claims. The k-means analysis elucidates intricate patterns and potential solutions, offering profound insights into effectively managing these issues. These analytical advancements are crucial in identifying significant and manageable responses to reduce the frequency and impact of Variations and Claims in construction projects.

Semi-Interlocking Masonry (SIM) represents an innovative building system developed at the Centre for Infrastructure Performance and Reliability at The University of Newcastle, Australia. This system employs a unique approach to interlocking mortar-less engineered masonry panels constructed from SIM units. These units are designed to offer substantial energy dissipation capacity, primarily attributed to the friction occurring on the sliding bed joints between the units within the panel during seismic events. The primary aim of this study is to evaluate the viability of incorporating semi-interlocking masonry as infill panels in the construction of multi-storey buildings across diverse geographical locations with varying seismic conditions in Australia. To assess the feasibility of SIM panels in different conditions (according to Australian Standard AS1170) in Australia, a comprehensive analysis using Strand7 is conducted on a three-storey structure incorporating traditional masonry infill panels and SIM panels. The comparison of displacement and base shear capacities is carried out in response to seismic events across various scenarios in different locations within Australia. The insights gained from this comparative analysis contribute valuable information regarding the viability of implementing SIM as a contemporary construction material.

This study addresses the critical need for standardizing Building Information Modeling (BIM) Execution Plans (BEPs) in the Architecture, Engineering, Construction, and Operations (AECO) sector. By analyzing 36 BEP documents from international organizations, we identify key elements and propose a comprehensive framework aimed at enhancing digital transformation and collaboration in complex construction projects. This research employs scientometric analysis to map the evolution of BEP standards and integrates empirical data from industry surveys to validate the proposed framework. Our findings highlight the benefits of standardized BEPs in reducing inefficiencies and improving project outcomes, thereby providing a significant contribution to the field of BIM implementation.

Densely urbanized areas, with a low percentage of green vegetation, are highly exposed to Heat Waves (HW) which nowadays are increasing in terms of frequency and intensity also in the middle-latitude regions, due to ongoing Climate Change (CC). Their negative effects may combine with those of the UHI (Urban Heat Island), a local phenomenon where air temperatures in the compact built up cores of towns increase more than those in the surrounding rural areas, with significant impact on the quality of urban environment, on citizens health and energy consumption and transport, as it has occurred in the summer of 2003 on France and Italian central-northern areas. In this context this work aims at designing and developing a methodology based on aero-spatial remote sensing (EO) at medium-high resolution and most recent GIS techniques, for the extensive characterization of the urban fabric response to these climatic impacts related to the temperature within the general framework of supporting local and national strategies and policies of adaptation to CC. Due to its extension and variety of built-up typologies, the municipality of Rome was selected as test area for the methodology development and validation. First of all, we started by operating through photointerpretation of cartography at detailed scale (CTR 1: 5000) on a reference area consisting of a transect of about 5x20 km, extending from the downtown to the suburbs and including all the built-up classes of interest. The reference built-up vulnerability classes found inside the transect were then exploited as training areas to classify the entire territory of Rome municipality. To this end, the satellite EO HR (High Resolution) multispectral data, provided by the Landsat sensors were used within a on purpose developed "supervised" classification procedure, based on data mining and “object-classification” techniques. The classification results were then exploited for implementing a calibration method, based on a typical UHI temperature distribution, derived from MODIS satellite sensor LST (Land Surface Temperature) data of the summer 2003, to obtain an analytical expression of the vulnerability model, previously introduced on a semi-empirical basis.

At present, farmland abandonment（FA）is a severe phenomenon in China, imposing a serious restriction on agricultural production. In this context, it is of great significance to explore the logical relationship between high-standard farmland construction (HSFC) and FA to optimize land resource allocation and guarantee national food security. Based on 838 samples of farmers in the main rice production area of the Yangtze River Basin in China, this paper employs the Tobit model, the mediating effect model, and the moderated mediating effect model to analyze the impact of HSFC on FA at the micro level. The results show that (1) HSFC inhibits FA, and FA proportion decreases by 1.14% for every 1% increase in HSFC proportion, and the robustness test and endogeneity treatment also yield consistent conclusions. (2) Agricultural socialization services (ASS) play a positive mediating role in the influence path. HSFC promotes farmers' purchase of ASS, which in turn inhibits FA. (3) The agricultural labor transfer distance (ALTD) plays a positive moderating role in the relationship between HSFC and FA. The farther the distance, the more likely HSFC can promote farmers' purchase of ASS and inhibit FA. The results provide enlightenment on how to precisely implement HSFC policy, that is, to inhibit FA by improving the construction of high-standard farmland and the post-construction management as well as protection system. Moreover, this study helps guiding the development of ASS and optimizing the institutional environment for agricultural labor transfer, creating conditions for agricultural scale management.

Construction using earth materials demonstrates ecological sustainability using locally sourced natural materials and environmentally friendly demolition methods. In this study, the environmental impact of adding cement to soil materials for rammed-earth farmhouse construction in rural China was investigated and comparatively simulated using the One Click LCA database, focusing on the conflict between sustainability objectives and the practical aspects of cement addition. By analyzing how the addition of cement aligns with local construction practices and by addressing the debate surrounding the inclusion of cement in rammed earth construction, our objective is to provide insights into achieving a balance between the environmental impact and the pragmatic considerations of using cement in earthen building practices. Three local structure scenarios are evaluated via simulations: a cement-stabilized rammed earth wall, a fired brick wall, and a localized reinforced concrete frame structure. The quantitative environmental impacts are assessed, and the qualitative differences in adaptation, economic sustainability, and other factors are examined in the context of present-day development in rural China. The results show that the use of cement-stabilized rammed earth wall-supported structures is associated with higher embodied carbon emissions compared to structures supported by reinforced concrete frames and enclosed by brick walls; however, these emissions are lower than those for brick wall-supported structures, while effectively meeting the structural requirements. In addition, the use of cement-stabilized earth for perimeter walls simplifies material management and disposal throughout the building's life cycle, and the cost-effectiveness of cement has been found to be substantially greater than that of reinforced concrete frames and brick structures, improving economic viability and social acceptability, especially among low-income communities in rural areas.

The construction sector of the Kingdom of Saudi Arabia (KSA), valued at USD 152 billion and employing 2.54 million people by 2023, is crucial to its economy. However, it faces challenges such as delays, disputes, and cost overruns. This study aims to address these issues by implementing Building Information Modeling (BIM) in the KSA, based on an extensive literature review highlighting the role and significance of BIM in mitigating construction claims. BIM improves collaboration, communication, and data integration among stakeholders. Hence, this study proposes a comprehensive BIM package framework comprising Revit Architecture, Microsoft Project, and Cost-X to reduce claims effectively. Validated through a KSA claims case study with a USD 1,870,000 claims value and 360-day delay, the BIM package significantly reduced the claims value to USD 188,000 and saved 275 days. Interview sessions were conducted to validate the effectiveness of the BIM package; 95% favored the use of BIM, 86% supported NEC4 contract adoption alongside BIM, 100% acknowledged BIM's potential in reducing design errors, 95% were confident in the case study's accuracy, and 82% were satisfied with data accuracy. This study confirms that BIM is an effective approach for minimizing construction claims in the KSA.

The purpose of this article is to present an IoT architecture implemented in an intelligent environment, focusing on the optimization of initial conditions and device management. A general control system was developed using an open-source platform, integrating aWi-Fi network and YAML coding to enable communication and control of the IoT architecture devices. The implementation includes actuators, sensors, and control devices that, through a graphical interface, allow the visualization of the historical record of activities and real-time measurements of connected devices. The design includes specific mechanisms and the analysis of materials through tensile tests on specimens, following the ASTM E8 standard, and deformation test simulations, in which PLA demonstrated better performance compared to materials like ABS and resin. The significance of the implemented IoT system lies in an energy saving of 58% compared to conventional structures. Additionally, the study of response times for network connections showed that using an Ethernet cable resulted in a response time of 1.21 seconds, representing a reduction of 1.65 seconds compared to the second lowest value obtained.

This publication aims to create 4K UHD video sequences with a specific focus on smart cities and transport. The created database will be accessible to all experts in the field and can be further used for research purposes. All reference video sequences will be transcoded into different quality settings. The resolution, compression standard, and bitrate will be changed. The work will aim to find out the best combination of video parameters from the measured values. Thanks to the overall evaluation, we will ensure for each single video sequence the quality with the best experience for the providers that will offer the service. The database will also be available with its objective and subjective ratings, with dynamicity information characterized by spatial and temporal information. After, It will be possible to compare the results of the subjective evaluation of a selected sample of our respondents with the work of other researchers who can evaluate with a different sample of evaluators.

Fires in houses are inevitable and they cause loss of life and major repair costs for the damage structure and contents. There is a clear need to prevent its ignition and spread to adjacent areas. This article presents the steps taken, namely: contacts, data collection, tests, analysis and conclusions regarding the accident resulting from the outbreak and spread of a fire, on December 25, 2020, in a traditional Portuguese house in Arganil, Portugal. The owners and the court requested to carry out an expert opinion by a person with specialized technical-scientific knowledge, which led to this work as an expert. the work consists of carrying out observations and data analysis. Then, the observed and analysed data were laboratory tested in order to consistently identify characteristics that lead to the ignition and propagation of the fire. This work identified construction problems, materials used and heat sources that are responsible for the accident. The conclusions may be used to avoid future incidents or accidents with houses of same construction type.

Cement production contributes to about 7% of CO2 emissions into the atmosphere. Despite our best efforts, we cannot find a competitive substitute that is both reliable and environmentally friendly. The simplest way to solve the problem is to rationalize the resources and try to minimize its use by substitute them with other materials. A concrete that contains a substantial amount of fly ash is already available, but its use is limited by the current shortage in the market and reduced initial resistance. In this context, ternary mixtures have been used to conduct an experiment. A significant volume of cement has been replaced with fly ash and metakaolin, which serves as a correction factor for the performance. In this work the main advantages and disadvantages of the simultaneous use of these two additions, which may reveal to be very interesting with high volumes of substitution will be presented. The performance of this ternary mixture is very promising. Provide a wide range of possibilities for replacing cement, maintaining or even improving its mechanical and durability properties. A solution for an ecological concrete with enhanced performance for general use in construction as an alternative to conventional concrete.