In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

The article presents the results of studies aimed to identify the effect of foliar treatments of winter wheat, sugar beets and soybeans with mineral and bioorganic fertilizers. Their positive effect on increasing the concentration of mineral forms of nitrogen in soil was revealed. The crop types have a greater influence on the size of nitrous oxide emissions: in winter wheat crops - 679 µg/m3, soybeans - 637.2 µg/m3, sugar beets - 576.8 µg/m3. The amounts of nitrous oxide emissions were lower in the variants without the use of phosphorus-potassium fertilizers. The Ruter AA fertilizer showed the greatest efficiency on winter wheat crops - 42.7 c/ha. Soybean grain yield of 44.2 c/ha was also achieved by using Ruter AA, as well as Geo-humate together with phosphorus-potassium fertilizers. On the background of the actual supply of phosphorus and potassium, maximum yield was obtained when using N30 on the leaf - 39.3 c/ha. Foliar feeding ensured a yield of sugar beet root crops of up to 67.1-77.4 c/ha on the backdrop of the application of phosphorus-potassium fertilizers with the advantage of using Amino turbo. The largest yield of sugar beet roots without use of mineral phosphorus and potassium was ensured by N30 treatment of the leaf in the phases of 4-6 and 8 leaves - 63.2 t/ha. Of the organo-mineral fertilizers and biostimulants, the best result was shown by the use of Ruter A - 62.6 t/ha. We believe that foliar feeding of crops can be a sustainable farming method that can increase crop yields and reduce N2O emissions.

Present study on land use land cover analysis and taluka wise combination of cropped area, carried out in Beed district of Maharashtra state in India and studied 11 talukas of the district. Secondary data on land use land cover and area in various crops has been collected, compiled and analyzed from various secondary sources. Simple descriptive statistics used to examine the agricultural land use land cover and J.C. Weaver’s crop combination technique was used for taluka wise analysis of crop combinations and on the basis of highest to smallest area engaged in particular crop, crops have been ranked. The study showed that, in the district as a whole, percentage of uncultivated land other than fallow was about 46 percent as compare to net sown area is only 35 percent in total geographical area (1063855ha) of Beed district. The study further revealed that about 42 percent area engaged in food crops and about 58 percent area occupied by nonfood crops, which includes cereals (25%), cotton (19%), pulses (13%), oilseed (12%), sugarcane (5%) and fruits and vegetables (3%). Results of Weaver’s crop combination technique showed that the Wadwani taluka demarcated as most diversified taluka by means of maximum number (sixteen) of crops combinations with the lowest variance value (14) found in the present investigation. Further, the study revealed that the high crop diversity found in Dharur taluka with eighteen crop combinations and the taluka has given first rank amongst others. To derive the crop diversity ranking, taluka wise maximum to minimum number of crop combinations derived in different talukas and given ranks accordingly. The study concluded that, agricultural land use analysis is essential for solving and optimizing the land use problem, maintaining socio-ecological balance, best utilization of scarce resources. The authors enlightened that the rational use of agricultural land has important for food security and biodiversity which increase the productivity and profitability of the agriculture sector and it indicates the decision making ability of farmers in study area.

The use of chemical pesticides in agriculture contributes to soil, water and air pollution, biodiversity loss and can harm non-target species. The European Commission has already established a Harmonized Risk Indicator to quantify the progress in reducing the risks linked to pesticides. Therefore, there is an increasing need to promote biopesticides or so-called low-risk pesticides (LRP). Extract from Melaleuca alternifolia – tea tree oil (TTO) is known for its antiseptic, antimicrobial, antiviral, antifungal, and anti-inflammatory properties. Tea tree oil has been extensively studied in pest management as well as in the pharmaceutical and cosmetic industry and there are already products based on its active substances on the market. This review focuses on the overall evaluation of tea tree oil in terms of effectiveness and safety as a biopesticide for the first time. The collected data can be an added value for further evaluation of tea tree oil in terms of the authorization extension as a fungicide in 2026.

Recent technological advancements in conservation genetics and genomics have resulted in diverse tools for aiding conservation of species. The precision and resolution of high throughput sequencing technologies provide valuable insights to aid conservation decisions, but these technologies are often financially unfeasible or unavailable in resource constrained countries. Inter-Simple Sequence Repeat (ISSR) markers, when combined with sensitive automated detection systems, provide a simple, cheap means to investigate genetic diversity and discriminate closely related species. Here we apply this technology to assess genetic diversity and taxonomic delimitation in the Encephalartos eugene-maraisii species complex, a highly threatened, taxonomically dubious group of cycads in South Africa. Our analyses support taxonomic singularity of E. dyerianus, E. dolomiticus and E. eugene-maraisii. Relationships between E. nubimontanus and E. cupidus remain uncertain. E. middelburgensis samples showed no clustering but had poor amplification success. This study demonstrates the suitability of automated ISSR fingerprinting as a method for plant conservation studies, especially in resource-constrained countries, and we make recommendations as to how this methodology can be effectively implemented.

In view of the fact that the field monitoring information can more intuitively and accurately reflect the stability state of slopes, this paper takes the warning threshold of slope deformation rate monitoring as the slope stability evaluation standard, and puts forward a method for solving the safety coefficient of rocky slopes. The discrete element method 3DEC, which is suitable for rocky slopes, is selected as the numerical calculation tool, and the convergence criterion of its strength reduction method is modified to the slope deformation rate threshold, and the method is realized by the bifurcation method through its built-in FISH programming language. The results of the classical case show that, by selecting the slope deformation rate threshold in the appropriate interval, the results of this paper's method are very close to those of the finite unit stress method and the limit equilibrium method, which verifies the reliability of this paper's method. Further, the method of this paper is applied to an open-pit mine slope project, based on the slope deformation on-site monitoring data, through the time series prediction method to determine the slope deformation rate warning threshold, using the threshold as an evaluation criterion to solve the slope's coefficient of safety, the calculation results show that: the slope's coefficient of safety in natural working conditions is 1.086, basically stable, suffered from continuous rainfall, the slope body is gradually saturated, the slope's coefficient of safety is reduced to 0.987, the slope's safety is reduced to 0.987. After continuous rainfall and gradual saturation of the slope, the coefficient of safety decreased to 0.987, destabilizing and destroying, which is consistent with the site conditions.

:Peat substrate is made from peat from drained peatlands, which is a limited resource. A realistic estimate is that 50% of the world’s wetlands have been lost. Peat is used in horticulture, especially for the cultivation of vegetables in greenhouses. The consequences of peatland exploitation are an in-crease in the greenhouse effect and a decrease in carbon stocks. Wood fiber can be used as an al-ternative to peat. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the growing container. This study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) variety “Dirigent H” developed in the Netherlands, were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) con-ventional fertilization (CF); (2) N13; (3) N23; (4) N30. The experiment was carried out in three repli-cations. As the amount of wood fiber increased, the humidity and pH of the growing medium in-creased. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in 50/50 and 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat sub-strate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

Revealing the spatial distribution mechanism of the coupling effect between soil water and salt is essential for managing saline-alkali farmland. This study utilized the multifractal method to analyze soil water and salt under varying water content levels in arid saline-alkali farmland. Soil samples were collected on the second (S1), fifth (S2), eighth (S3), eleventh (S4), and fourteenth (S5) days after a rainfall event. The findings showed that a significant decrease in soil water content, contrasting with an increase in soil salt content throughout the soil layers post-rainfall. As water content decreased, the spatial variability of soil water initially increased from S1-3 and then decreased, while the spatial variability of soil salt decreased. The spatial distribution between soil water and salt exhibited a high correlation at S3-4 (with relative water content of soil ranging from 0.52 to 0.75) due to their coupling effect. However, soil salt was unevenly leached by rainfall at high water content levels (S1-2) and precipitated at low water content levels (S5), resulting in low spatial variability correlations between soil water and salt. This study elucidated the coupling process of soil water and salt, identifying their spatiotemporal distribution mechanism in dryland agricultural areas.

Batch and transport experiments were used to investigate the remediation of a loamy sand soil contaminated with Cr(VI) using zero valent iron nanoparticles (nZVI) stabilized by the carboxy methyl cellulose (CMC-nZVI). The effect of pH, ionic strength (IS), and flow rate on the removal efficiency of Cr(VI) were investigated under equilibrium (uniform transport) and non-equilibrium (Two-site sorption) transport using the Hydrus-1D model. The overall removal efficiency ranged from 70 to over 90% based on the chemical characteristics of the CMC-nZVI suspension and the transport conditions. The concentration and pH of the CMC-nZVI suspension had the most significant effect on the removal efficiency and transport of Cr(VI) in the soil. The average removal efficiency of Cr(VI) was increased from 24.1 to 75.5% when the concentration of CMC-nZVI nanoparticles was increased from 10 to 250 mg L-1, mainly because of the increased total surface area at larger particle concentration. Batch experiments showed that removal efficiency of Cr(VI) was much larger under acidic conditions. The average removal efficiency of Cr(VI) reached 90.1 and 60.5 % at pH 5 and 7, respectively. The Two-site sorption model described quite well (r2 = 0.96-0.98) the transport of Cr(VI) in soil as compared to the uniform transport model (r2 = 0.81-0.98). The average retardation of Cr(VI) was 3.51 and 1.61 at pH 5 and 7, respectively, indicating earlier arrival for the breakthrough curves and shorter time to reach maximum relative concentration at lower pH. The Hydrus-1D model has proven to be an efficient tool for assessing the removal of Cr(VI) pollutants, offering innovative, cost-effective, and environmentally friendly remediation methodologies.

Our study aimed to assess sprinkler irrigation's impact on the activity of selected soil enzymes concerning nitrogen metabolism and oxidation-reduction processes in the soil with different doses of inorganic nitrogen fertilizers. The soil Alfisol was sampled from the experimental field of spring barley in the University Research Center in the central part of Poland in the moderate transitory climate during the growing seasons 2015–2017. The index resistance (RS) was derived to recognise the resistance enzymes of drought. In the maturity phase, nitrate reductase activity was at an 18% higher level in irrigated soils and the activity of other enzymes was higher in no-irrigated treatments by 25% in dehydrogenase, 22% in peroxydase 33% in catalase and 17% in urease case. The development stage of barley influenced nitrate reductase activity. Enzymatic activity has been changing in the examined years of the research, depending on the weather conditions. During the maturity stage, the soil's lower ammonium nitrogen content resulted from higher spring barley uptake due to drought stress. Irrigation probably contributes to increased leaching of nitrate in soil. The highest index of resilience was presented in the soil catalase activity.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

Phosphite (Phi) has gained attention in agriculture due to its biostimulant effect on crops. This molecule has been found to benefit plant performance by providing protection against pathogens, improving yield and fruit quality, and improving nutrient and water use efficiency. It is still unclear how Phi enhances plant growth and protects against multiple stresses. It has been hypothesized that Phi acts by directly affecting the pathogens and interacting with the plant cellular components and molecular machinery to elicit defense responses. This study delves into elucidating the mechanisms underlying Phi’s beneficial effects on plants, revealing a complex interplay with fundamental signaling pathways. A RNA-seq study of Arabidopsis seedlings under optimal and limiting phosphate conditions helped us unveil Phi’s role in promoting plant growth by activating the expression of genes involved in the biosynthesis and signaling pathways associated with abscisic acid (ABA), salicylic acid (SA), and jasmonic acid (JA). Expression of ABA-related genes, known for their involvement in stress response and development regulation, is triggered by Phi treatment, contributing to enhanced resilience and growth. Simultaneously, the activation of the SA pathway, associated with defense responses, suggests Phi’s potential in bolstering plant immunity. Moreover, Phi influences JA biosynthesis and signaling, which are crucial for defense against herbivores and pathogens, thereby strengthening plants’ defenses. Our findings reveal a multifaceted mechanism through which Phi benefits Arabidopsis development. Understanding its intricate interplay with key signaling pathways opens avenues for leveraging Phi as a strategic tool to enhance plant resilience, immunity, and growth in agricultural and ecological contexts.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Maintaining sufficient levels of plant nutrients in the soil and controlling certain heavy metals, which can be toxic to the environment, are critical to ensure sustainable agricultural production. The study aimed to assess the linkage of crop-specific agricultural practices established by farmers in the Kvemo Kartli region (Georgia) with metal accumulation in soils of agricultural lands being subject to influence from polluted irrigation water in the past. In particular, we tried to identify the primary sources of micronutrients, including iron (Fe), copper (Cu), manganese (Mn), nickel (Ni), and zinc (Zn), and toxic elements such as cadmium (Cd) and lead (Pb), and share of the contaminated irrigation water and other factors related to agricultural practices under different land uses, such as intensive and extensive arable farming, vineyards, orchards, and permanent pastures having the least disturbed soil. Based on principal component analysis, five primary sources were identified and categorized according to farmers' interviews and previous studies conducted in the region. The results showed that increased concertation of plant-available Cu, Zn, Cd and Pb were mainly associated with irrigation water and intensive use of fungicides; Fe, Mn, and Ni were closely linked to several factors, such as the mineralogical composition of soils, mineral and organic fertilizers inputs, and atmospheric deposition from diffuse sources, where exhausts from transport are probably the primary source. During our study, we attempted to differentiate irrigation water inputs from fungicides using simulation based on irrigation pattern and irrigation water quality on the one hand and fungicide application rate and their metal content on the other. The simulation revealed that the intensive application of fungicides, especially in vineyards, is more significant in enriching soils with Cu and Zn than irrigation water. Identification of factorial dependences was supported by statistical analysis and application of a number of contamination assessment methods: Contamination Factor (CF), Pollution Load Index (PLI), single-factor Pollution Index (PI), Nemerow’s comprehensive pollution index (PIN), Enrichment Factor (EF), and Geo-Accumulation Index (Igeo). Applied environmental indices indicate that the soils under the former and existing vineyards are the most enriched with Cu and Zn, highlighting the significance of agricultural practices on heavy metals accumulation in soils of agricultural lands.

This study investigates the relationship between housing prices and vacancy rates in Hong Kong, offering insights distinct from previous cross-sectional analyses. Addressing limitations in data availability and methodological approaches, the study examines annual data spanning multiple housing size categories to uncover nuanced dynamics in the housing market. Two major contributions emerge: firstly, the analysis reveals the price elasticity of vacancy, elucidating how housing prices respond to changes in vacancy rates over time. Secondly, by considering housing vacancy changes as outcomes of the interactions between supply and demand, the study challenges the conventional independence assumption between these variables. The results support the hypothesis that housing vacancies exert a negative impact on housing prices, holding other factors constant. These findings have significant implications for policymakers, urban planners, and real estate investors, providing valuable insights for crafting targeted interventions and informing investment decisions.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

The impact of antecedent soil moisture content on soil erosion is a complicated phenomenon, which is still under argument with contradictions in research results. Hence, the objective of this study is to investigate the impact of antecedent soil moisture content to soil loss on clay soil by conducting two-year field experiments under natural rainfall on runoff plots with length of 10 meters, width of 3 meters, and uniform slope of 9%. Volumetric soil moisture sensors were used to log soil moisture changes, and soil moisture readings were used along with rainfall records to quantify the antecedent soil moisture conditions for each rainfall event. Results of this study show duration of the effective erosion event outranks the antecedent volumetric soil moisture content. Field study also suggests that accumulative rain falling within 48 hours (Pp48) prior to an effective erosion event strongly correlated with soil loss per Rainfall-Runoff Erosivity Index (Soil Loss / EI30), particularly when the duration of an effective erosion event is either between 3 ~ 7 hours or 10~ 30 hours. Hence, Pp48 can be considered as an alternative to replace antecedent soil moisture content in RUSLE 2’s cover and management factor.

Mangroves offer vital ecological advantages including air and water filtration, coastal and estuarine habitat provision, sediment stabilization, and wave energy absorption. Their intricate root systems play a key role in safeguarding shorelines from tsunamis and erosive storms by dissipating wave energy. Moreover, mangroves shield against boat wakes and wind-waves, bolstering shoreline defense. Wave dissipation is a function of forest width, tree diameter, and forest density. Restoration efforts of juvenile mangroves in Florida’s Indian River Lagoon (IRL) aim to reduce wave energy in areas vulnerable to erosion. Physical model testing of wave dissipation through mangroves is limited due to the complexity in representing the mangrove structure, where prop roots are non-uniform in both diameter and location. Previous studies have quantified wave dissipating effects through use of scaled and parameterized mangrove structures. This study measures the dissipation effects of live mangroves in a wave flume, forced by conditions representative of the IRL. These measurements are used to validate a parameterized dowel model. Error between wave attenuation factors for the live mangrove and dowel system was on average 2.5%. Validation of the modularized dowel system allowed for further parameterized testing to understand forest structure effects, such as sediment stabilization and wave attenuation.

Halide perovskite materials gain enormous attention for their semiconducting properties, higher power conversion efficiency and potential applications in a wide range field of studies along with their two key limitations: stability and toxicity. In spite of great progress made on the halide perovskites and many promising research developments, overcoming these limitations is not realized yet. Therefore, coordination engineering of new framework for obtaining alternative new halide perovskite materials and fundamental understanding of the coordination chemistry and electronic interactions forming the structure of these newly engineered halide perovskite materials might be one way in order to overcome the issues related to both stability and toxicity. In this review, the current development of halide perovskite families, both lead halide perovskites and lead free halide perovskites followed by coordination engineering of the new frameworks to engineer new halide perovskite materials will be reviewed comprehensively. Moreover, all the concerns of the fundamental ideas of coordination chemistry and electronic interactions that are keys in forming the halide perovskite structures are discussed in detail and form the main aim of this review. Interestingly, we also discuss recent potential energy applications beyond photovoltaic and this review has completed with an essential and open question: ‘what could happen in the future of halide perovskites?’ in order to excite commercial enterprises and research institutions again as well as to get motivating new predictions on the future continuity of this field.

This paper discusses the bioethics of intellectual property (IP) and intellectual property rights (IPR) applicable to biotechnology-based IP. It outlines some of the laws that are related to IPR in Zimbabwe and globally. The paper additionally highlights gaps, opportunities and concerns with the laws. Finally, the paper highlights some initiatives already underway in Zimbabwe targeted at promoting entrepreneurship, commercialization and industrialization while proposing strategies that can be used to further promote the generation and granting of biotechnology-related IP and IPR in Zimbabwe.

In the Vietnamese Mekong delta, soil quality and crop yield are steadily declining under rice monocultures with three crops per year. The objective of this study was to evaluate the medium-term effects of rotating rice with upland crops and adding organic amendments on rice yield and relate it to soil quality. A field trial with split-plot design including two factors and three replicates was carried out from 2017 to 2020, over the course of nine consecutive cropping seasons. Crop rotations and organic amendments were applied as main-plot and subplot factors, respectively. The rotations were: 1) rice–rice–rice (R–R–R), 2) soybean–rice–rice (So–R–R), and 3) sesame–rice–rice (Se–R–R), while organic amendment treatments included: i) no amendment (NO-AM); ii) compost of rice straw and cow manure (RS+CM), and iii) sugarcane compost (SGC); the composts were applied at a rate of 2.0 t ha-1. The rotation cycle started with the so-called spring–summer (SS), followed by summer–autumn (SA) and ended with the winter–spring (WS) season. Rice yield significantly (P < 0.05) increased by organic amendments after nine growing seasons (2019–2020 WS), with an increment of 5.1% for RS+CM (7.07 ton/ha) and 6.1% for SGC (7.14 ton/ha). Contrary to our expectation, rotations with upland crops did not significantly increase rice yield. Rice yield significantly and positively correlated with an integrated soil quality index SQI (r = 0.86) for the topsoil (0–15 cm), but not for the subsoil (15–30 cm). The increased availability of soil nutrients (Si and marginally also P) and improved soil physical properties probably induced by organic amendments, along with other soil properties under study, cumulatively attributed to enhanced rice yield. Use of a SQI involving several soil quality indicators enables to overall quantify the importance of soil fertility for rice yield versus other factors and it provides an effective means of quantifying the integrated effect of improved management. Moreover, integrating a wide range of soil quality indicators in a SQI ensures its applicability across diverse settings, including different crop rotations and various soil types.

Our work is regarding the analysis of land use changes, in the light of “saving soil” against the expansion due to unearned plus value of land: The loss of natural and agricultural surface in front of the expanding urban environment is a critical aspect of unsustainability of urban development, especially in the way it was carried out in the past decades. The measure of the physical transition of land use and characters from a more natural condition of land surface to a new artificial one, joint with a parallel analysis of the increase of land value due to such change is nowadays a major land-policy tool. The interplay of urban economics regulation with planning, reveals new key issues in urban governance and environmental preservation. In this paper it will be shown some experiment about the impact assessment of soil take, related with the seek of valorization of property inside the planning process. Our paper reports as well about the experimental activity carried out inside the MITO Lab of the Polytechnic of Bari, where reports about property values and environmental values have been produced, specially looking at the reality of the Apulia, a southern Italian Region, that is rich of farmlands and coastlines, often invaded by constructions with a severe loss of nature, landscape and ecosystems services.

The Katerini-Kolindros aquifer system (KKas) is a critical freshwater resource, essential for the local and regional economy. To understand contamination sources, groundwater flow paths, and assess the aquifer's health, an extensive dataset of 751 samples from 113 wells collected between 2010 and 2020 was analyzed using multivariate statistical analysis (MVSA) and hydrogeochemical diagrams. The prevailing water types identified were Ca-HCO₃ and Mg-HCO₃, with mixed water types resulting from various factors affecting groundwater quality. The chemistry of groundwater in the KKas is shown to be affected by ion exchange processes and to a lesser extent by reverse ion exchange processes. No indications of sea-water intrusion have been identified in the water wells monitored. On the other hand, nitrate contamination has been detected in specific water wells spatially associated with urban-type land uses and activities. It is considered that nitrate contamination originates primarily from septic tanks and urban sewage networks or secondarily from fertilization of football pitches, cemeteries or urban waste management practices.

In Ethiopia, farmers have changed cropland to Eucalyptus globulus plantations for construction, fuelwood and economic benefits. However, it has adverse effects on soil properties. The investigation was, therefore, to evaluate the impact of Eucalyptus globulus plantations on soil properties in northwestern Ethiopia. About 30 soil samples were collected from two soil depths (0-20 and 20-40 cm) and three land uses (Eucalyptus globulus plantations, cropland and grazing land) with five replications. Soil properties were analyzed using a two-way analysis of variance (ANOVA). Based on the result, soil properties such as silt particles, moisture content (MC), organic matter (OM), total nitrogen (TN) and cation exchange capacity (CEC) were significantly higher under the soil of Eucalyptus globulus plantations than in cropland and grazing land. Whereas the lower contents of bulk density (BD), soil pH, available phosphorus (AP), electrical conductivity (EC) and exchangeable bases (Ca, Mg, K, and Na) were recorded in Eucalyptus globulus plantations. Besides, clay, BD, MC, pH, EC, CEC, percent base saturation (PBS) and basic cations increased with soil depth while decreasing sand, silt, TP, OM and AP. The basic cations ( Ca, Mg, K), PBS and AP decreased in the soil of the 25-year old Eucalyptus globulus plantation compared to cropland by 38%, 36%, 43 %, 45% and 47% and grazing land by 56%, 60%, 76 %, 60% and 56%, respectively. Therefore, appropriate and effective land use management principles should be implemented in the study area.

Colleges and universities play a crucial role in fostering innovation, making it essential to explore effective strategies for promoting innovation at the institutional policy level. This paper focuses on the establishment of intellectual property (IP) model cities as a starting point and conducts an empirical analysis using innovation data from 234 cities and 942 colleges and universities between 2007 and 2017. By constructing a multi-temporal double-difference model, this study reveals that the establishment of IP model cities effectively fosters innovation in colleges and universities. Further analysis demonstrates that this promotion effect is particularly significant in the western region, key cities, key colleges and universities, as well as in the fields of invention and utility model patents. These conclusions withstand a series of robustness tests, confirming their validity. In terms of the underlying mechanisms, it is found that the national IP pilot city policy has a substantial impact on university innovation by promoting research and development (R&D) investment and strengthening innovation cooperation. The insights provided by this study offer valuable policy recommendations for leveraging the innovation potential of the IP model city policy, thereby driving economic transformation, upgrading, and fostering innovation development in China.

This paper examines certain implications from the literature on Tiebout’s model of local gov-ernment service provision, particularly Hamilton’s extension of the model to include local control of land use and property taxation. Our empirical analysis focuses on the use of fiscal zoning to lower property tax rates, a topic that has not been addressed in the extensive Tiebout literature. Using data for over 100 municipalities in the Miami, Florida, metropolitan area, we specify property tax rates as a function of fiscal zoning measures, other municipal characteristics, and tax mimicking. We conclude that single-family zoning is by far the most important variable ex-plaining municipal property tax rates.

This study investigates how root environment acidification impacts tea seedlings and the role of magnesium (Mg) in mitigating these effects. We examine varying pH and Mg levels' influence on tea seedlings' resistance to abiotic stress, focusing on antioxidant capacity and nutritional content. In a hydroponic experiment, we varied root pH (3.5, 5.0, 6.5) and Mg concentrations (0.01, 0.4, 0.8 mM), assessing parameters like antioxidant capacity, peroxidative damage, and nutritional content at 1, 7, 15, and 30 days post-treatment. Root environment acidification and Mg deficiency worsened peroxidative damage in tea plant leaves and roots. Increased Mg supplementation enhanced antioxidant enzyme activity, reducing malondialdehyde and mitigating oxidative damage from root environment acid stress. Under acid stress, 0.8 mM Mg significantly increased tea leaf polyphenols, amino acids, and water-soluble extracts. Mg notably boosted chlorophyll content, surpassing lower Mg levels at pH 5. Additionally, Mg reversed root vitality inhibition induced by acid stress, leading to increased nitrogen, potassium, and Mg concentrations in leaves, promoting balanced nutrient absorption. Mg supplementation is crucial for enhancing tea plant antioxidant capacity, alleviating growth inhibition from root environment acid stress, and improving chlorophyll content and root vitality, highlighting Mg's significance in tea cultivation and broader agricultural practices.

Bi1-xSbx crystal is one of the best n-type thermoelectric materials below 200 K, but its weak mechanical strength hinders practical applications for deep refrigeration. Herein, we adopted the mechanical enhancement method of hot extrusion to investigate the comprehensive mechanical and thermoelectric properties of Bi0.905Sb0.095. It revealed that reducing the grain size of the matrix and increasing the extrusion ratio can improve the gain size uniformity and mechanical properties. While the thermoelectric performance depends on the texture, grain size, and local composition. The extruded sample prepared by ingot with the high extrusion ratio of 9:1 generated a high texture degree of (001) plane and small grain sizes between ~4-40 mm, which resulted in the high bending strength of Bi1-xSbx ~130 Mpa and a high-power factor of ~ 68 μW·cm-1·K-2@173 K, as well as the relative high figure of merit of 0.25@173K. This work highlights the importance of the uniform distribution of the grain size and the compositions for Bi1-xSbx, as well as the required universal key parameter for the hot-extrusion method.

(1) Background: Parents of children with autism spectrum disorders often experience psychological distress, which can affect the quality of childcare they provide. It is crucial to screen for psychiatric symptoms among these parents. The Core Symptom Index (CSI) is a widely used tool for assessing general symptoms such as depression, anxiety, and somatic symptoms, with demonstrated validity and reliability across various populations. However, there is limited research on the validity and reliability of the CSI in the general Chinese population. This study aimed to investigate the psychometric properties of the Chinese version of the CSI among parents of children with autism spectrum disorders using Confirmatory Factor Analysis (CFA). (2) Methods: A total of 794 Chinese parents raising children with autism participated in this study. All completed the CSI, along with the social inhibition subscale of the Interpersonal Problems Inventory and the Couple Satisfaction Index. Factorial validity was assessed using CFA to determine how well the bifactor three-factor model fits the data. Various structural models were compared using model fit indices. Convergent and discriminant validity were examined by exploring correlations with the social inhibition subscale and the Couple Satisfaction Index. Invariance testing of the CSI was conducted across multiple groups based on gender, age, and education using CFA. The reliability of the CSI was evaluated using McDonald’s omega coefficients. (3) Results: The bifactor model emerged as the best-fitting model for the data, suggesting that the total score of the CSI adequately represents overall psychiatric symptoms. The CSI exhibited significant correlations with the social inhibition subscale (r = 0.41, p < 0.01) and smaller correlation coefficients with the Couple Satisfaction Index (r = -0.16, p < 0.05), indicating both convergent and discriminant validity. Invariant tests supported scalar invariance levels based on gender and age but only partial invariance for education. The Chinese version of the CSI demonstrated high consistency, with McDonald's omega coefficients ranging between 0.86 and 0.95. (4) Conclusions: The bifactor model of the Chinese version of the CSI is validated, making it a suitable tool for measuring depression, anxiety, and somatization symptoms among parents of children with autism spectrum disorders. Further research on other Chinese populations is encouraged.

Water is a fundamental resource for ecosystems, humans, and the development of all economic sectors; it is necessary to identify and evaluate its environmental pressures or impacts. The water footprint (WF) is an appropriate indicator for the consumption of water used to produce a product. The present study uses this tool to evaluate the green and blue water requirements and the sustainability of irrigation water use for agroindustrial avocado production in Ziracuaretiro, Michoacán (2012-2021). Our analysis was based on aggregating weather and soil data at the municipal level and official government databases of avocado cultivated surface, fruit production, and water rights concessions. The analysis considers the homogeneity of information throughout the study area. We estimated that rainfed plantations require 839.03 m³/ton and irrigated plantations require 2355.80 m³/ton, with an average of 1597.47 m³/ton. In addition, we determined that avocado cultivation can demand up to 124.3% of agricultural water concessions in this municipality. In addition to the WF estimates, the analysis indicates that such studies are fundamental for decision-makers to develop and implement water use-efficiency strategies and shows the need for further research related to water consumption of avocado as a crop at more detailed scales to reduce uncertainty.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

South Africa (SA) is grappling with a severe food insecurity crisis exacerbated by socioeconomic challenges. This resulted in the Department of Basic Education (DBE) advocating for the establishment of vegetable gardens at schools. However, information on the suitability of the soils in SA for sustainably growing Beetroot is unavailable. This study aimed to assess the suitability of soils for sustainable Beetroot production at various schools in the Kgakotlou circuit. Four Secondary Schools were selected: Mothimako, Madipoane, Klaas Mothapo and Phomolong. A detailed soil survey was carried out to study soils in vegetable gardens. Soil samples were collected for laboratory analysis of physicochemical properties. The soil suitability was evaluated using the physicochemical properties of the soils and optimal soil requirements for Beetroot production. We found various soils in the schools, including Cambisols (Hutton and Nkonkoni), Leptosol (Glenrosa), Plinthosol (Westleigh), and Acrisols (Tshiombo and Tubatse). Portions of the gardens on Hutton and Westleigh soil were moderately suitable (S2), limited by electrical conductivity (EC). Meanwhile, portions of Tshiombo, Tubatse, and Nkonkoni were marginally suitable (S3), limited by pH and EC. Portions on Glenrosa soil at Klaas Mothapo and Phomolong were not suitable (NS) and were limited by shallow depth, soil pH and EC. The results reveal the importance of considering soil suitability before establishing vegetable gardens in school settings. Indexing soil suitability using the physicochemical properties of soil resources for sustainable beetroot production is proposed for schools in the Kgakatlou circuit and other parts of SA.

Soil organic matter (SOM) is essential for nutrient cycling and soil carbon (C) accumu-lation, both of which are heavily influenced by the quality and quantity of plant litter. Since SOM dynamics in relation to plant diversity are poorly understood we investigated the effects of willow variety and mixture, and site on the soil C stocks, SOM chemical composition and ther-mal stability. Using pyrolysis-field ionization mass spectrometry we analysed the top 10 cm of soil from two 7-year-old experimental sites in Germany and Sweden, with monocultures and mixtures of two willow varieties (Salix spp.) belonging to different species. Overall, site had the strongest effect on SOM quality. Results showed significant variability across sites for willow identity and mixture effects on C accumulation and SOM chemistry. In the German site (Ros-tock), yearly soil C accumulation was higher (p < 0.05) for variety ‘Loden’ (1.0 Mg C ha-1 year-1) compared to ‘Tora’ (0.5 Mg C ha-1 year-1), whilst in the Swedish site (Uppsala), both varieties ex-hibited similar soil C accumulation rates of around 0.6 Mg C ha-1 year-1. Willow variety identity significantly affected SOM quality at both sites, while mixing had minor effects. Our findings emphasize the significance of site-specific context and variety or species identity in shaping soil C accumulation in willow plantations.

Background: Antibiotic resistance is an urgent issue everywhere in the globe. It is necessary to look into new sources of antibiotics to address this issue. Aim of the study: studying the purification of Corallopyronin B from various soil conditions in Egypt, as well as the antibacterial effectiveness of Corallopyronin B in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Several soil conditions in Egypt were examined to create bacterial isolates that generated the antibiotic chemical Corallopyronin B. Using reversed-phase HPLC, Myxopyronin B was purified. The test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity were ascertained using the paper disc diffusion assay and the broth microdilution technique. Furthermore, in stages 1/2 of randomized clinical trials including human and animal models, pharmacokinetics, adverse drug reactions, and the in vivo antibacterial spectrum were discovered. Results: The soil bacterial isolate Corallococcus coralloides DSM 2259, grown on a Casein yeast peptone( CYP) plate, produced Corallopyronin B from its culture supernatant. At MICs more than 100 mcg/ml, the test antibiotic inhibited the growth of many Gram -ve bacteria, including Escherichia coli, while preventing the growth of numerous Gram +ve bacteria, with MICs ranging from 1 to 10 mcg/ml. Eukaryotic cells, on the other hand, including those in humans and fungi, were unharmed. The test antibiotic was shown to have a bactericidal effect by inhibiting bacterial DNA-dependent RNA polymerase( RNLP). In phases 1/2 of randomized human clinical trials, when 600 mg of the dose per 70 kg of body weight was administered SC, the Cmax was 8.6 mcg/ml at Tmax 1 hour; T1/2 reached 136 min following first-order kinetics of elimination. It stopped acting around 6-7 hours after SC was administered. In the preclinical and randomized human clinical trial phases 1/2, less than 6 percent of experimental candidates had uncommon toxicity, showing reduced bile flow. Protein binding with plasma albumin was detected which reached about 83%. Conclusion: The current work was noteworthy since it involved the production of the bactericidal antibiotic Corallopyronin B from Corallococcus coralloides DSM 2259 which was isolated from several soil environments in Egypt.

Oncomelania Hupensis is the exclusive intermediary host of Schistosoma japonicum in China. The alteration of its habitat and population distribution directly affects the safety of millions of individuals residing in the Yangtze River Economic Belt (YREB), and the ecological stability. Therefore, it is crucial to analyse the influence of climate change on the distribution of O. Hupensis in order to achieve accurate control over its population. This study utilised the MaxENT model to forecast possible snail habitats by utilising snail distribution data obtained from historical literature. The subsequent outcomes were achieved: The primary ecological factors influencing the distribution of O. Hupensis are elevation, minimum temperature of coldest month, and precipitation of wettest month; Furthermore, future climate scenarios indicate a decrease in the distribution area and a northward shift of the distribution centre for O. hupensis; Specifically, those in the upstream will move northeast, while those in the midstream and downstream will move northwest; These changes in suitable habitat area, the average migration distance of distribution centers across different climate scenarios, time periods, and sub-basins within the YREB, resulting in uncertainty. This study offers theoretical justification for the prevention and control of O. hupensis along the YREB.

Soil organic matter (SOM) is important for the global carbon cycle, and hyperspectral remote sensing has proven a promising method for fast SOM content estimation. However, soil physical properties significantly affect the sensitivity of satellite hyperspectral imaging to SOM, leading to poor generalization ability of the estimation model. This study aims to improve the spatiotemporal transferability of the SOM prediction model by alleviating the coupling effect of soil physical properties on the spectra. Based on satellite hyperspectral images and soil physical variables, including soil moisture (SM), soil surface roughness (root mean squared height, RMSH), and soil bulk weight (SBW), a soil spectral correction strategy was established based on the information unmixing method. Two important grain-producing areas in Northeast China were selected as study areas to verify the performance and transferability of the spectral correction model and SOM content prediction model. The results showed that soil spectral corrections based on fourth-order polynomials and the XG-Boost algorithm had excellent accuracy and generalization ability, with residual predictive deviations (RPD) exceeding 1.4 in almost all bands. In addition, when the soil spectral correction strategy was adopted, the accuracy of the SOM prediction model and the generalization ability after model migration were significantly improved. The SOM prediction accuracy based on the XG-Boost corrected spectrum was the highest, with a coefficient of determination (R2) of 0.76, root mean square error (RMSE) of 5.74 g/kg, and RPD of 1.68. The prediction accuracy, R2, RMSE, and RPD of the model after migration were 0.72, 6.71 g/kg, and 1.53, respectively. Compared with the direct migration prediction of the model, adopting the soil spectral correction strategy based on fourth-order polynomials and XG-Boost reduced the RMSE of the SOM prediction results by 57.90% and 60.27%, respectively. The performance comparison highlighted the advantages of considering soil physical properties in regional-scale SOM prediction.

Thromboembolic conditions, such as stroke and myocardial infarction [MI], are the primary causes of mortality globally. High efficiency was demonstrated by fibrinolytic enzymes isolated from microbial sources in dissolving various blood clots. The study aimed to investigate and produce bacterial fibrinolytic enzymes from various Egyptian soil conditions using recombinant DNA technology. Fifty soil samples were examined to determine the production of fibrinolytic enzymes. The plasmin plate technique assessed the thrombolytic activities of the strong fibrinolytic enzyme-producing bacterial isolates. In addition to determining the molecular mass using a mass spectrometer and the western blot method, the activity and thermostability of the enzymes were characterized. An affinity chromatography approach was used to purify the fibrinolytic enzymes. However, bacterial recombinant DNA technology produced the pure bacterial fibrinolytic enzyme. Several dosage formulations for the formulation of fibrinolytic enzymes were tested. By using affinity chromatography and the SDS-PAGE test, the isolated bacterial fibrinolytic enzyme in this investigation was almost 83% pure. Bacillus cereus ATCC 4342 was identified as the predominant bacterial isolate secreting fibrinolytic enzymes. It was discovered that the fibrinolytic enzyme activity of fifty soil samples ranged from 0.167 U/ml to 1.853 U/ml. The extracellular enzyme extracted from Bacillus cereus culture supernatant demonstrated a relatively stable fibrinolytic activity over 18 hours at a pH range of 7.4–10, as well as stability with maximum productivity at 43℃ for over 60 minutes. In this investigation, the enzyme was referred to as Fibrin-proteinase[ FP]. The fibrin clots were directly thrombolyzed by the FP. The calculated values for the specific activity and molecular mass of the FP were approximately 40.71 units/mg of protein and approximately 30 KDa, respectively. It was observed that the presence of Fe+3 marginally boosted protease activity, but the presence of EDTA decreased it. On the other hand, adding monovalent cations like K+1 and Na+1 significantly increased the fibrinolytic activity of FP. The enzyme exhibited activity throughout the temperature range of 20 to 65℃, peaking at 55℃. The ideal range for the generation of protease was 35–43℃ and 8.0–10. The thermostable fibrinolytic enzyme FP, which was isolated from Bacillus cereus ATCC 4342 in various soil environments in Egypt during the current study, was a promising fibrinolytic enzyme because it demonstrated a more extensive and effective fibrinolytic activity and fewer side effects than the fibrinolytic enzymes that are currently available worldwide. It is advised that further research be done on optimizing the right formulation of bacterial fibrinolytic enzymes in the future to help dissolve different types of blood clots and, as a result, lower the high death rate that exists worldwide.

Transport of carbon, major and trace element by rivers in permafrost-affected regions is one of the key factor of circumpolar aquatic ecosystem response to climate warming and permafrost thaw. While seasonal and annual export fluxes (yields) of carbon (C) and inorganic solutes are fairly well known for all large Arctic rivers, spatial variations in elementary concentration along the river length and among its tributaries remain poorly understood. Moreover, the landscape factors controlling riverine element concentration in permafrost-affected regions are still poorly constrained. This is especially true for the largest river of Eastern Siberia, the Lena River, which drains through continuous permafrost zones with highly variable lithology and vegetation. Here we present the results of C, major and trace element measurements over a 2600-km transect of the Lena River main stem (upper and middle reaches) including its 30 tributaries, conducted at the peak of the spring flood. There were two main group of solutes in the main stem depending on their spatial pattern: i) elements that decreased their concentrations downstream, from SW to NE (Cl, SO4, DIC, Li, B, Na, Mg, K, Ca, As, Sr, Mo, Sb, Ba and U), which probably reflected a decrease in the proportion of carbonate rocks in the watershed and the degree of groundwater feeding, and ii) elements that increased their concentrations downstream (Al, Ti, Cr, Fe, Ga, Rb, Y, Zr, Nb, Cs, REEs, Hf and Th), which was tentatively linked to an increase in organic C stock in soils, larch forest coverage and enhanced mobilization of lithogenic elements from silicate soil minerals. Based on landscape parameters of Lena tributaries, we tested the impact of major environmental factors on major and trace element spatial pattern. Among all the variables, the proportion of sporadic permafrost on the watershed strongly controlled concentrations of soluble highly mobile elements (Cl, B, DIC, Li, Na, K, Mg, Ca, Sr, Mo, As and U). Another important factor of element concentration control in the Lena River tributaries was the coverage of watershed by light (B, Cl, Na, K, U) and deciduous (Fe, Ni, Zn, Ge, Rb, Zr, La, Th) needle-leaf forest (pine and larch). The latter, however, could also reflect the DOC-enhanced transport of low-soluble trace elements in the NW part of the basin. This part of the basin is dominated by silicate rocks and continuous permafrost, as compared to carbonate rock-dominated and groundwater-affected SW part of the Lena River basin. Overall, the impact of rock lithology and permafrost on major and trace solutes of the Lena River basin during the peak of spring flood was mostly detected at the scale of the main stem. Such an impact for tributaries was much less pronounced, because of the dominance of surface flow and lower hydrological connectivity with deep groundwater in the latter. Future changes in the river water chemistry linked to climate warming and permafrost thaw at the scale of the whole river basin are likely to be linked to changes in spatial pattern of dominant vegetation, rather than to the permafrost regime. We argue that comparable studies of large, permafrost-impacted rivers during most contrasting seasons, including winter baseflow, should allow efficient prediction of future changes in riverine ‘inorganic’ hydrochemistry induced by permafrost thaw.

Background: Antibiotic resistance is an urgent issue everywhere in the globe. It is necessary to look into new sources of antibiotics to address this issue. Aim of the study: studying the purification of Corallopyronin B from various soil conditions in Egypt, as well as the antibacterial effectiveness of Corallopyronin B in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Several soil conditions in Egypt were examined to create bacterial isolates that generated the antibiotic chemical Corallopyronin B. Using reversed-phase HPLC, Myxopyronin B was purified. The test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity were ascertained using the paper disc diffusion assay and the broth microdilution technique. Furthermore, in stages 1/2 of randomized clinical trials including human and animal models, pharmacokinetics, adverse drug reactions, and the in vivo antibacterial spectrum were discovered. Results: The soil bacterial isolate Corallococcus coralloides DSM 2259, which was grown on a Casein yeast peptone( CYP) plate, produced Corallopyronin B from its culture supernatant. At MICs more than 100 mcg/ml, the test antibiotic inhibited the growth of many Gram -ve bacteria, including Escherichia coli, while also preventing the growth of numerous Gram +ve bacteria, with MICs ranging from 1 to 10 mcg/ml. Eukaryotic cells, on the other hand, including those in humans and fungi, were unharmed. The test antibiotic was shown to have a bactericidal effect by inhibiting bacterial DNA-dependent RNA polymerase( RNLP). In phases 1/2 of randomized human clinical trials, when 600 mg of the dose per 70 kg of body weight was administered SC, the Cmax was 8.6 mcg/ml at Tmax 1 hour; T1/2 reached 136 min following first-order kinetics of elimination. It stopped acting around 6-7 hours after SC was administered. In the preclinical and randomized human clinical trial phases 1/2, less than 6 percent of experimental candidates had uncommon toxicity, which showed up as reduced bile flow. Protein binding with plasma albumin was detected which reached about 83%. Conclusion: The current work was noteworthy since it involved the production of the bactericidal antibiotic Corallopyronin B from Corallococcus coralloides DSM 2259 which was isolated from several soil environments in Egypt.

Background: Antibiotic resistance is an overwhelming serious difficulty globally. This necessitates the exploration of novel sources of antibiotics to overcome this challenge. Aim of the study: Bacterial Myxopyronin A production from various soil environments Egypt; as well as testing its antimicrobial activity in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Different soil environments in Egypt were screened for the growth of bacterial isolates producing Myxopyronin A as an antimicrobial agent. Purification of Myxopyronin A was performed via reversed-phase HPLC. Paper disc diffusion assay, as well as the Broth dilution technique, were exploited to assess the invitro antimicrobial and minimum inhibitory concentration( MIC) of the test antibiotic. Furthermore, in vivo antimicrobial spectrum, adverse drug reactions, and pharmacokinetics were detected during animal model testing stages and human randomized clinical trials phases 1/2. Results: From the culture supernatant of the Myxobacterium Myxococcus fulvus 124B02 which was the predominant soil bacterial isolate grown on the Casein yeast peptone plate, Myxopyronin A was produced. The test antibiotic blocked the growth of many Gram +ve bacteria with MICs less than 100 mcg/ ml. In contrast, it inhibited the growth of a few Gram -ve bacteria such as Escherichia coli at MICs greater than 100 mcg/ ml. On the other hand, Eukaryotic cells such as fungal and human cells were not affected. Prokaryotic DNA-dependant-RNA polymerase( RNLP) was noticed to be inhibited via the test antibiotic suggesting its bactericidal action. The maximum concentration was 7-8 mcg/ ml at a maximum time of 2 hours when 600 mg dose was orally administered in randomized human clinical trials phases 1/2, and T1/2 reached 2.5 hours following first-order kinetics of elimination. The duration of its action was nearly 12 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and cholestatic jaundice in less than 5 % of experimental candidates. Conclusion: The present study was promising due to the bactericidal antibiotic Myxopyronin A production from Myxococcus fulvus 124B02 isolated from different soil environments in Egypt.

In On Revolution, Hannah Arendt makes the case that a constitution must account for the need of the human person to participate in the building of society, both as a primordial and continual action of founding. This paper draws on Arendt's insight on the relationship between privacy and the notion of property, both of which the constitution must protect, as it is dependent on those notions. Property in its fullest sense is the means by which a person interacts with others and establishes a society. Particularly important for this notion of engagement are the concepts of shame and the love of goodness. The actor emerges from the private sphere to interact with others on the strength of the secrecy and confidentiality of her intimate, private relationships. Property is therefore essential to human flourishing and happiness. Following this, the activity of constructing the public forum on the basis of the private is an important feature of Arendt's constitutionalism. Human action showers third-party esteem on the actor's family and friends, binding them to the constitutional structure and strengthening familial relationships and social cohesion.

This paper is devoted to the study of reproducing kernels on 2-inner product Hilbert spaces. We focus on a new structure to produce reproducing kernel Hilbert and Banach spaces. According to multi-variable computing, this structures can be useful in electrocardiographs, machine learning and economy

The long-term use of fertilizers and pesticides in conventional cultivation has resulted in a decrease in soil productivity and vegetable yields in greenhouses. However, only a limited number of studies have explored the impacts of organic cultivation on greenhouse soil. Specifically, there is a scarcity of research examining the alterations in soil aggregate mediated organic carbon and microbial communities, which are known to enhance soil productivity. This study investigated the properties of soil aggregates, including the levels of organic carbon fractions, microbial community, and enzyme activity with the three aggregate classes microaggregates (&lt;0.25 mm), small macroaggregates (2-0.25 mm) and large macroaggregates (&gt;2 mm). These investigations were conducted under three different cultivation methods in a greenhouse: conventional cultivation (CC), integrated cultivation (IC), and organic cultivation (OC) in greenhouse. The results showed that (1) OC and IC promoted the formation of small macro-aggregates and enhanced aggregate stability compared to CC, (2) SOC in the three size fractions of OC increased by 98.99%-92.06% compared to CC; EOC increased by 98.47%-117.59%; POC increased by 138.59%-208.70%; MBC increased by 104.71%-230.61%; DOC increased by 21.93%-40.90%, respectively; (3) Organic cultivation significantly increased enzyme activity in all three particle size aggregates and increased the relative abundance of bacteria in micro-aggregates as well as the relative abundance of fungi in small macro-aggregates. Structural equation model (SEM) analysis revealed that organic farming practices fostered the development of smaller macro-aggregates, elevated microbial and enzyme activities within soil aggregates, and facilitated the conversion of soil nutrients and carbon sequestration. consequently, this led to an increase in soil organic carbon content and improved vegetable yield in greenhouse environments. In conclusion, the soil carbon content and vegetable yield are enhanced through long-term organic cultivation in greenhouses, primarily by increasing the proportion of small macro-aggregates.

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

BACKGROUND: Thromboembolic disorders including Myocardial infarction[ MI] and stroke represent the leading causes of death worldwide. Fibrinolytic enzymes extracted from microbial sources showed high efficacy in the dissolution of different blood clots. AIM OF THE STUDY: Screening and the bacterial recombinant DNA manufacture of bacterial fibrinolytic enzymes from different soil environments in Egypt. METHODOLOGY: A total of 50 soil samples were screened for their fibrinolytic enzyme production. The potent fibrinolytic enzyme-producing bacterial isolates were evaluated for their thrombolytic activities using the plasma plate method. The characterization of the enzyme activity and thermostability were carried out; also, the determination of molecular mass using a mass spectrometer and western blot technique was performed. The purification of the fibrinolytic enzymes was done through the affinity chromatography technique. On the other hand, the production of the purified bacterial fibrinolytic enzyme was achieved via bacterial recombinant DNA technology. Formulation of fibrinolytic enzymes in different dosage forms was tried. RESULTS: In the present study, the purified bacterial fibrinolytic enzyme was approximately 83% pure through affinity chromatography and SDS-PAGE assay. The predominating bacterial isolate secreting fibrinolytic enzymes was found to be Bacillus cereus. The fibrinolytic enzyme activities of 50 soil samples were found to be in the range of 0.167-1.853 U/ ml. The fibrinolytic activity of the extracellular enzyme refined from the culture supernatant of Bacillus cereus was relatively stable over the PH range from 7.4-10 for 18 hours and also it showed stability with the highest productivity at a temperature of 43 0C for nearly 60 minutes. The enzyme was called fibrin-proteinase[ FP] in the present study. The FP degraded the fibrin clots via direct thrombolysis. The specific activity and the molecular mass of the FP were estimated to be nearly 40.71 Units/ mg protein and nearly 30 KDa respectively. Protease activity was noticed to be slightly increased in the presence of Fe+3; While it was inhibited in the presence of EDTA. On the other hand, the FP fibrinolytic activity was enhanced greatly after the addition of monovalent cations such as K+1 and Na +1. The enzyme was also active over the temperature range of 20- 65 0C with the highest activity at 55 0C. The optimum temperature and PH of protease production was at 35-43 0C and PH 8.0-10. Conclusion: During the present study, the thermostable fibrinolytic enzyme FP purified from Bacillus cereus in different soil environments in Egypt was a promising fibrinolytic enzyme because it showed a broader efficacious fibrinolytic activity as well as less adverse effects than the current fibrinolytic enzymes globally. It is recommended in the future advanced exploration of the optimization of suitable formulation of bacterial fibrinolytic enzymes to aid in the dissolution of various blood clots and as a consequence overcoming the high rate of mortality globally.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Background: Across the world, antibiotic resistance is a critical challenge. To address such a problem, it has to be done to investigate new antibiotic sources. Aim of the study: Study of the antibacterial activity of Corallopyronin A in preclinical animal testing and randomized human clinical trials stages 1/2, as well as investigating the purification of Corallopyronin A from different soil conditions in Egypt. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were tested to develop bacterial isolates that produced the antibiotic compound Corallopyronin A. Reversed phase HPLC was used to purify Myxopyronin A. The broth microdilution method and the paper disc diffusion assay determined the test antibiotic's minimum inhibitory concentration( MIC) and in vitro antibacterial activity. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in phases 1/2 of randomized clinical studies involving humans and animal models. Results: Corallopyronin A was generated from the culture supernatant of the soil bacterial isolate Corallococcus coralloides M2, cultivated on a Casein yeast peptone( CYP) plate. The test antibiotic prevented the growth of several Gram-ve bacteria, including Escherichia coli, at MICs higher than 100 mcg/ ml; while blocking the development of many Gram +ve bacteria, with MICs ranging from 3 to 15 mcg/ ml. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. A bactericidal consequence of the test antibiotic was detected in the inhibition of prokaryotic DNA-dependent RNA polymerase( RNLP). Conclusion: The synthesis of the bactericidal antibiotic Corallopyronin A from Corallococcus coralloides M2 isolated from different soil settings in Egypt intrigued the current investigation.

This study outlines the development of an innovative method utilizing UHPLC-PDA for the simultaneous identification of polyphenols and bitter acids (alpha-acids, beta-acids, and iso-alpha-acids) in beer samples. The resulting chemical profiles were leveraged to distinguish the characteristics of four bergamot-flavored beers, each representing distinct styles (IPA, Lager, Blanche, and ALE), produced on a pilot-scale plant. In a streamlined 29-minute analysis, twenty-nine polyphenols and fourteen bitter acids were successfully identified under optimized separation conditions. Rigorous validation, encompassing parameters such as Limit of Detection (LOD), Limit of Quantification (LOQ), R-squared (R2), repeatability, and reproducibility, was conducted for polyphenol quantification using constructed calibration curves with seven levels. Exploring polyphenolic components as potential discriminators among different beer styles, a total of thirty-two polyphenolic compounds were identified and quantified, including characteristic bergamot peel polyphenols like neoeriocitrin, naringin, and neohesperidin. The determination of bitter units and total phenols further aided in style differentiation. Multivariate analysis provided additional insights into variations among specific beer styles, revealing discrepancies in the presence or relative concentrations of specific compounds linked to brewing ingredients and processes. This research enhances to trace the fingerprinting of the chemistry governing beer quality through a straightforward and cost-effective analytical approach, readily applicable in common laboratories.

This study aims to improve the shaft with hexagon joints to be a type not requiring welding or bolts in the static load test . In order to evaluate the bearing capacity of helical piles, two sites were selected to conduct pile installation for the field test and the pile load test. For the pile load test, the static pile load test and the dynamic pile load test were carried out, and torque was measured during pile installation for the field test to compare and analyze expected bearing capacity and thus assess the feasibility of the method for estimating the bearing capacity. The field pile load test revealed the bearing capacity of the gravity grout pile was the same or greater than 600kN in the static pile load test in accordance with AC 358 Code. The non-grout pile showed the bearing capacity the same or smaller than 600kN, suggesting gravity grouting is required. Moreover, the field pile load test was used to establish the bearing capacity equation considering the torque in pile installation, and a small number of samples were used to establish the equation which can be used as a basic data.

The soil organic matter (SOM) content and stability in natural gypsum soils and soils from mining/industrial areas were compared, in terms of their physical, chemical and micromorphological properties, to determine whether the old brownfield soils were acting as carbon (C) sinks, counteracting increasing carbon dioxide concentrations in the atmosphere. The mining/industrial soils were 50–400 years old, so had been left sufficiently long for full self-restoration. Despite having very different origins, both natural and brownfield soils stored similar amounts of SOM, and had similar pH values, calcium carbonate contents and textures. They were also fully covered with similar grass plant communities. The mining/industrial soils exhibited similar microstructures to the gypsum soils and were often quite porous. The most striking difference between them and the natural gypsum soils was that the mining/industrial soils were strongly polluted with zinc, lead and cadmium. The 50-year-old brownfield soils differed from the others in terms of having a lower state of SOM transformation, with a much higher C/N ratio, lower aggregate water resistance index, lower dehydrogenase activity and greater areas of undecomposed or slightly decomposed plant residues. These parameters in the older (150–400 years) brownfield soils were similar to those of the natural soils.

Successful fertilization treatments targeted to improve stand productivity while reducing operational complexities and cost depend on a clear understanding of soil nutrient availability under varying environmental conditions. Soil nutrient data collected from 154 forest sites throughout the Inland Northwest, USA were analyzed to examine soil nutrient characteristics on different geologic soil parent materials and to rank soil fertility. Results show that soil parent material explains significant differences in soil nutrient availability. Soils developed from volcanic rocks have the highest CEC and are relatively high in P, K, S, Mg, Cu, Ca, and B, but generally poor in N. Forest soils developed from plutonic rocks exhibit the lowest CEC and are low in N, S, K, Mg, Cu, and Ca, but higher in P. Some soils located on mixed glacial till are low only in K, Cu, Mg, and Ca, but many glacial soils are relatively rich in other nutrients, albeit the second lowest CEC. Soils developed from metasedimentary and sedimentary rocks are among those with lowest soil nutrient availability for P and B. Sulfur was found to have the highest concentrations in metasedimentary influenced soils and the least in sedimentary derived soils. Our results should be useful in designing site-specific fertilizer and nutrient management prescriptions for forest stands growing on soils developed from these major geologies within the Inland Northwest region of the United States.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

BACKGROUND: Thromboembolic disorders including Myocardial infarction[ MI] and stroke represent the leading causes of death worldwide. Fibrinolytic enzymes extracted from microbial sources showed high efficacy in the dissolution of different blood clots. AIM OF THE STUDY: Screening and the bacterial recombinant DNA manufacture of bacterial fibrinolytic enzymes from different soil environments in Egypt. METHODOLOGY: A total of 50 soil samples were screened for their fibrinolytic enzyme production. The potent fibrinolytic enzyme-producing bacterial isolates were evaluated for their thrombolytic activities using the plasma plate method. The characterization of the enzyme activity and thermostability were carried out; also, the determination of molecular mass using a mass spectrometer and western blot technique was performed. The purification of the fibrinolytic enzymes was done through the affinity chromatography technique. On the other hand, the production of the purified bacterial fibrinolytic enzyme was achieved via bacterial recombinant DNA technology. Formulation of fibrinolytic enzymes in different dosage forms was tried. RESULTS: In the present study, the purified bacterial fibrinolytic enzyme was approximately 83% pure through affinity chromatography and SDS-PAGE assay. The predominating bacterial isolate secreting fibrinolytic enzymes was found to be Bacillus cereus. The fibrinolytic enzyme activities of 50 soil samples were found to be in the range of 0.167-1.853 U/ ml. The fibrinolytic activity of the extracellular enzyme refined from the culture supernatant of Bacillus cereus was relatively stable over the PH range from 7.4-10 for 18 hours and also it showed stability with the highest productivity at a temperature of 43 0C for nearly 60 minutes. The enzyme was called fibrin-proteinase[ FP] in the present study. The FP degraded the fibrin clots via direct thrombolysis. The specific activity and the molecular mass of the FP were estimated to be nearly 40.71 Units/ mg protein and nearly 30 KDa respectively. Protease activity was noticed to be slightly increased in the presence of Fe+3; While it was inhibited in the presence of EDTA. On the other hand, the FP fibrinolytic activity was enhanced greatly after the addition of monovalent cations such as K+1 and Na +1. The enzyme was also active over the temperature range of 20- 65 0C with the highest activity at 55 0C. The optimum temperature and PH of protease production was at 35-43 0C and PH 8.0-10. Conclusion: During the present study, the thermostable fibrinolytic enzyme FP purified from Bacillus cereus in different soil environments in Egypt was a promising fibrinolytic enzyme because it showed a broader efficacious fibrinolytic activity as well as less adverse effects than the current fibrinolytic enzymes globally. It is recommended in the future advanced exploration of the optimization of suitable formulation of bacterial fibrinolytic enzymes to aid in the dissolution of various blood clots and as a consequence overcoming the high rate of mortality globally.

The objectives of the study were to determine the spatial rate of CO₂ flux (Net Ecosystem Exchange) and soil moisture in a wetland ecosystem applying Sentinel-1 IW (Interferometric Wide) data of VH (Vertical Transmit/Horizontal Receive—cross polarization) and VV (Vertical Transmit/Vertical Receive—like polarization) polarization. In-situ measurements of carbon flux, soil moisture, and LAI (Leaf Area Index) were carried out over the Biebrza Wetland in north-eastern Poland. The impact of soil moisture and LAI on backscattering coefficient (σ°) calculated from Sentinel-1 data showed that LAI dominates the influence on σ° when soil moisture is low. The models for soil moisture have been derived for wetland vegetation habitat types applying VH polarization (R² = 0.70 to 0.76). The vegetation habitats: reeds, sedge-moss, sedges, grass-herbs, and grass were classified using combined one Landsat 8 OLI (Operational Land Imager) and three TerraSAR-X (TSX) ScanSAR VV data. The model for the assessment of Net Ecosystem Exchange (NEE) has been developed based on the assumption that soil moisture and biomass represented by LAI have an influence on it. The σ° VH and σ° VV describe soil moisture and LAI, and have been the input to the NEE model. The model, created for classified habitats, is as follows: NEE = f (σ° Sentinel-1 VH, σ° Sentinel-1 VV). Reasonably good predictions of NEE have been achieved for classified habitats (R² = 0.51 to 0.58). The developed model has been used for mapping spatial and temporal distribution of NEE over Biebrza wetland habitat types. Eventually, emissions of CO₂ to the atmosphere (NEE positive) has been noted when soil moisture (SM) and biomass were low. This study demonstrates the importance of the capability of Sentinel-1 microwave data to calculate soil moisture and estimate NEE with all-weather acquisition conditions, offering an important advantage for frequent wetlands monitoring.

In this paper, we study the weighted reproducing kernels. We introduce a generalization of weighted reproducing property and extend it to relative reproducing property on Banach spaces. This generalization will develop the parallel computing and it can be used as a base of parallel learning for machines especially in the case that there are non-homogenous weighted hypothesis. This methods formulate learning and estimation problems in a relative reproducing kernel Banach space (RRKBS) of functions defined on the data domain, expanded in terms of a kernel.

Heavy metals constitute pollutants particularly common in air, water, and soil. They are present in both urban and rural environments, on land and in marine ecosystems, causing serious environmental problems since they do not degrade easily, remain almost unchanged for long periods, and bioaccumulate. Detection, though especially quantification, is a systematic process as monitoring of their levels needs to be carried out at regular intervals since there is often seasonal variation. The need for rapid and low-cost determination of metals is therefore considerable. In the present study atomic absorption spectroscopy (AAS), using a flame or graphite furnace, and square wave anodic stripping voltammetry (SWASV), using a bismuth thin film electrode, a sensitive voltammetric method is being compared and analytically validated. Atomic absorption spectroscopy (AAS) represents a well-established analytical technique while anodic stripping voltammetry is being criticized for its applicability in complicated sample matrices such as soil samples. This sample-handling challenge is being investigated in the present study. The results show that both methods AAS and ASV were satisfactorily correlated and showed that the concentration of metals is lower than the limit values, but with increasing trend. Therefore, continuous monitoring of metal levels in the urban complex of the city is necessary and a matter of great importance. Regarding Cd, the detection limits of Cd are lower compared to those of AAS when using the graphite furnace, while an overestimation was noted when using flame-AAS in comparison with those found with SWASV. The SWASV method has the advantage of being cheaper and faster, enabling the simultaneous determination of heavy elements across the range of concentrations that these elements can occur in Mediterranean soils. Additionally, we applied a dsDNA-modified electrode which can be used in the speciation analysis of Cu(I) and Cu(II). The changes in the characteristic peaks of guanine and adenine can be applied in the redox speciation analysis of copper in soil which represents an issue of great importance.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

Ammonium sulfate has been utilized in agriculture; however, there is a dearth of research on its application in maize cultivation subsequent to the implementation of nitrification inhibitors or coating. This study aims to analyze the impacts of various combinations of ammonium sulfate fertilizers on soil nutrients, plant nutrient uptake, yield, and fertilizer utilization efficiency in maize cultivation to ascertain the optimal and stabilized disposal method for ammonium sulfate. A completely randomized design was employed with five treatments (AU, the control using urea; AS, treatment using ammonium sulfate; ASN, treatment using ammonium sulfate with a nitrification inhibitor; ASG, treatment using oil-coated ammonium sulfate; ASD, treatment using oil-humic acid-coated ammonium sulfate). Results showed that: (1) Compared with AU and AS, ASN, ASG and ASD decreased the leaching rates of TN, NH4+-N and NO3-N to the 10-20 cm soil layer, and more residual N was obtained in 0-10 cm soil layer. The first-order kinetic equation Nt=N0(1-e-kt) can better fit the process of nitrogen accumulation and release, and the N release rate constant is AU>CK>AS>ASH>ASN>ASD; (2) Compared with AU and AS treatments, the plant dry weight, grain dry weight, spike width, spike length, and yields of maize increased by 8.85-11.08%, 12.98-14.15%, 2.95-3.52%, 5.50-5.65%, and 43.21-51.10% under ASG treatment respectively. The impact of effective spike number on maize yield was found to be significant, as demonstrated by the path analysis conducted in this study. Furthermore, the accumulation levels of nitrogen, phosphorus, and potassium within above-ground plants significantly increased under the ASG treatment compared to the AU and AS treatments. The partial productivity of nitrogen, phosphorus, and potassium increased by 1.43-1.51-fold under ASG treatment, while grain nitrogen balance, grain phosphorus balance, and grain potassium balance increased by 1.41-1.58-fold, 1.51-1.95-fold, and 1.15-l.96-fold respectively. The oil-coated ammonium sulfate, therefore, exhibited the optimal slow-release effect of nutrients, thereby achieving superior performance in enhancing maize production and efficiency.

SOC stock (SOCS) changes caused by land use changes are still unclear, and understanding this response is essential for many environmental policies and land management practices. In this study, we investigated the temporal-spatial and vertical distribution characteristics of SOCS on the Western Sichuan Plateau (WSP) using the sparrow search algorithm-random forest regression (SSA-RFR) models with excellent model applicability and accuracy. The temporal-spatial varia-tions in the SOCS were modeled using 1080 soil samples and a set of nine environmental covariates. We analyzed the effect of land use changes on the SOCS on the WSP. The total SOCS increased by 18.03 Tg C from 1990 to 2020. The results of this study confirmed that the SOCS in the study area has increased significantly since 2010, with an increase of 27.88 Tg C compared to the total SOCS in 2010. We found that the spatial distribution of the SOCS increased from southeast to northwest, and the vertical distribution of the SOCS in the study area decreased with increasing soil depth. Forest and grassland are the main sources of SOCS, the total SOCS in the forest and grassland accounted for 37.53 and 59.39% of the total SOC pool in 2020, respectively. Expansion of the wetlands, forest, and grassland areas could increase SOCS in the study area.

The substitution of chemical fertilizers by organic manure plays a critical role in sustainable crop production. Nevertheless, organic amendments promote the global warming potential (GWP) in rice paddies due to increased methane (CH4) emissions. Increasing evidence shows that lime application can reduce CH4 emissions from acidic paddy soils, while it is still not clear whether liming can reduce the GWP in rice fields under organic manure substitution. A two-year field experiment was conducted to investigate the impacts of pig manure substitution and lime application on grain yield, CH4 and nitrous oxide (N2O) emissions in a subtropical double-cropped rice field in China. The experiment consisted of three treatments: chemical fertilization (CF, 100% N from urea), 50% of chemical N substituted by pig manure (1/2N + M), and the 1/2N + M treatment plus lime amendment (1/2N + M + L). On average, 1/2N + M reduced rice yield by 5.65% compared to CF, while lime application had no effect on rice yield. Mean cumulative CH4 emissions were 218.8% higher in 1/2N + M than in CF, whereas 1/2N + M + L reduced CH4 emissions by 36.6% compared to 1/2N + M. Neither pig manure substitution nor lime application affected N2O emissions. Consequently, 1/2N + M increased the GWP and greenhouse gas intensity (GHGI) by 214.6% and 228.3%, respectively, compared to CF. In contrast, 1/2N + M + L reduced the GWP and GHGI by 36.4% and 36.5% compared to 1/2N + M. Lime application can mitigate CH4 emissions and GWP induced by pig manure amendment in double-cropped rice fields.

The cuttlebone-like structure is a complex porous bionic structure with asymmetric sinusoidal S-shaped wall structure connecting laminar septa, and studies have shown that the cuttlebone-like structure has light weight, high strength and excellent energy absorption capability. It has become an important research to investigate the mechanical mechanism of cuttlebone-like structure and to design a bionic structure beyond nature structure based on it. In order to investigate the mechanical properties of the static compression and shearing processes of the cuttlebone-like structure, this paper establishes theoretical formulas and analyzes the influence of dimensionless parameters such as height-to-thickness ratio $\lambda$, period-to-thickness ratio $\xi$ and amplitude to period ratio $\eta$ on the compression and shearing processes with the help of ABAQUS finite element software.The parameter sensitivity analysis method was used to compare the important influence degree of each dimensionless parameter on the mechanical properties of the structure and to determine the relative optimal parameters of the structural mechanical properties under compression and shearing. Based on the relatively optimal parameter of the cuttlebone-like structure, the cross-sectional geometry of the structure is improved to build a new cuttlebone-like structure.The experimental results showed that the new cuttlebone-like structure with revised cross-section improved the mechanical properties of the cuttlebone-like structure.The study results are of theoretical guidance to enhance the mechanical properties and geometric design of cuttlebone-like structures.

Soil extracellular enzyme activity (EEAs) and enzymatic stoichiometry (ES) can provide a crucial indication of changes in soil ecosystem's nutrient availability and the microbial resource limitations. However, the changing characteristics of soil EEAs and ES at different stages of the native succession process and their key drivers are unclear. In order to investigate the soil EEAs, ES and driving factors of soil under vegetation at different succession stages, we adopted the "spatio-temporal substitution" method to collect the surface soil of bryophyte community, herbaceous community, shrub community and tree community in the new volcanic lava platform of Wudalianchi Volcanic Nature Reserve. We measured seven soil EEA, including carbon(C)-acquiring enzyme (β-1,4-glucosidase (BG)), N-acquiring enzymes (β-N-acetyl-glucosaminidase (NAG) and leucine aminopeptidase (LAP)) and phosphorus (P)-acquiring enzyme (acid phosphatase (AP)) activities. The length and angle of vectors defined by ratios of enzyme activities (BG/(NAG + LAP) vs. BG/AP) were used to indicate relative microbial investments in C- (length), and N- and P- (angle) acquiring enzymes. Our results showed that the contents of TC, TN, TP, MBC, DOC and NO3-N in shrub community soil were significantly higher than those in bryophyte, herb and tree communities, and increased by 441%, 246%, 137%, 5570%, 12% and 484%, respectively. The highest soil EEA of C-, N- and P-acquiring were found in shrub community, and the soil EEAs/MBC of C-, N- and P-acquiring were the highest in bryophyte community. Enzyme C:N, C:P and N:P ratios increased progressively in the order of bryophyte, herb and shrub community, but the enzyme C:N, C:P and N:P ratios of tree community were both far less than shrub community. Vector lengths increased progressively in the order of bryophyte (1.16), herb (1.27), tree (1.29) and shrub (1.40), and Vector angles decreased progressively in the order of bryophyte (49.15°), herb (45.65°), Tree (45.31°) and shurb (44.54°), suggested that as succession progresses, soil microbial nutrients transforms from P limitation (angle＞45°) to N limitation (angle＜45°). Redundancy analysis showed that TC, TN, EC and C:N were important drivers of variation in soil EEAs and ES in vegetation at different succession stages. Our findings highlight that the primary succession process cause nutrient limitation transformation. Soil ES might be a sensitive indicator mediated by soil microorganisms to the relative resource limitation at different stages of the primary succession process.

Abstract: Due to sever land degradation throughout Ethiopia, the government has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. However, most of the rivers in Ethiopia carry huge amount of sediment in rainy season and streams dried up in the dry period. Planned research was conducted on two paired micro-catchments Mt.Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were collected from 22/11/2020 to 8/11/2022 on both micro-catchments at their outlets and center respectively. Base flow separation was done using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software was employed for data analysis. Flow duration curve (FDC) for both watersheds were developed. The FDC indicated that the base flow from treated micro-catchment ishigher and sustained in the dry season while it is low and un-sustained in untreated micro-catchment. From statistical analysis, there is a significant difference in base flow enhancement between the treated and untreated micro-catchment (P<0.001). Hence, catchment treatment contributed to improve groundwater recharge and sustain base flow in the dry season by reduce surface runoff during rainy season.

To investigate the effects of organic fertilizer combined with reduced chemical fertilizer on radish yield, quality, and soil environment in high mountainous areas (elevation: 1800 m), and to mitigate the environmental pollution caused by excessive use of chemical fertilizers. The field trial was conducted to study the effects of different fertilizer treatments. (Control:local fertilizer application rate: 375 kg·hm² reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer; T1:12% reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer; T2:20% reduction in chemical fertilizer + 4500 kg·hm² of organic fertilizer; T3:28% reduction in chemical fertilizer + 4500 kg·hm² organic fertilizer). Four different fertilizer ratios were studied to assess their impacts on radish quality, yield, and soil environment. The findings showed that T2 significantly increased radish yield by 12.92%. Moreover, it led to significant improvements in the content of vitamin C, soluble sugars, soluble solids, soluble proteins, titratable acidity, and glucosinolates, which increased by 10.62%, 2.15%, 50.00%, 26.90%, 43.90%, and 44.57%, respectively. Treatment T2 also significantly increased soil nutrient content, with a 7.69% and 14.29% increase in total nitrogen and total phosphorus content compared to the control (Control) treatment, and a significant reduction of 21.64% in soil bulk density . T2 treatment significantly enhanced soil urease activity, sucrase activity, alkaline phosphatase activity, and catalase activity, showing an improvement of 28.97%, 55.92%, 52.08%, and 17.47% compared to the control, respectively (p&lt;0.05). Moreover, treatment T2 resulted in a relative abundance increase of 12.25% and 10.43% in Proteobacteria and Actinobacteria respectively. Thus, the combined application of T2:20% reduction in chemical fertilizer + 4500 kg·hm² of organic fertilizer improved the quality and yield of radish while optimizing the soil environment. T2 effectively promoted radish growth, enhanced radish yield and quality, and improved the soil environment.

Abstract: Severe land degradation is the principal environmental problem in Ethiopian highlands in the form of soil erosion, and soil fertility loss, which is caused by human intervention for food, shelter, and energy demands. Soil erosion contributes to the loss of precious soil and water resources which are the basis of agricultural production and provide numerous other eco-system services. The Ethiopian highlands are one of the most degraded regions in the world. To combat such problems, the government of Ethiopia has been implementing massive soil and water conservation works at the watershed scale since 2010 to conserve soil and water resources. Mount Yewel is one of the highlands in Northeastern Ethiopia where intensive soil and water conserva-tion has been implemented. Despite the massive investment in soil and water conservation measures, most of the rivers in the highlands of Ethiopia carry huge amounts of sediment with high flood risks in the wet season and streams are dried up in the dry period. Nonetheless, the impact of soil and water conservation measures on flood reduction and dry season flow en-hancement has not yet been quantified and evaluated. This research was then conducted on paired micro-catchments of Mount Yewel with the main objective of evaluating the impact of soil and water conservation measures on base flow modification. Stream flow and rainfall data were col-lected from 22/11/2020 to 8/11/2022 on paired micro-catchments of Mount Yewel at their outlets and centers respectively. Base flow separation was done from the stream hydrograph using Sp. Hydro base flow separation tool and SPSS Ver.21 statistical software were employed for data analysis. Flow duration curves (FDC) for both watersheds were developed to compare the stream flow patterns between treated and untreated micro-catchments of Mount Yewel. The FDC indi-cated that the base flow from treated micro-catchment is higher and sustained in the dry season while it is low and unsustained in untreated micro-catchment. From statistical analysis, there is a significant (P

The CuCrSn alloy is promising as high-strength and high-conductivity Cu alloy due to its relative low smelting requirement, while thus far reports on the CuCrSn alloy is still quite lacked. In this study, the microstructure and properties of Cu-0.20Cr-0.25Sn (wt%) specimens prepared under different rolling and aging combinations were comprehensively characterized, in order to reveal the effects of cold rolling and aging on the CuCrSn alloy. The results show that increasing the aging temperature from 400 ºC to 450 ºC can obviously accelerates the precipitation, and the cold rolling before aging significantly increases the initial microhardness and promotes the precipitation. Whereas, the deformation hardening will be eliminated during the aging process, making the microhardness even decrease monotonically when the aging temperature and the rolling ratio before aging are high. Performing the cold rolling after the aging can maximize the effects of precipitation strengthening and deformation strengthening, and its adverse impact on the conductivity is not serious. A tensile strength of 506.5 MPa and a conductivity of 70.33% IACS were obtained with such a treatment, only the elongation decreases. Different strength-conductivity combinations of the CuCrSn alloy can be achieved through appropriate combinations of the aging and post aging cold rolling conditions.

Purpose: The study investigates soil pores' impact on carbon dynamics and sequestration processes, examining their physical and chemical characteristics and their mechanisms for carbon sequestration.Research Method: Existing literature and research on soil pores, carbon dynamics, and carbon sequestration are analyzed. The interrelationships between soil pore structure, water movement, microbial activity, root penetration, carbon input, soil aggregation, and gas exchange are examined. Traditional techniques and advanced imaging methods are used to quantify and characterize soil pores.Findings: Soil pores play a critical role in facilitating carbon sequestration through various mechanisms. They affect water movement, microbial activity, root penetration, carbon input, soil aggregation, and gas exchange. Understanding these relationships is crucial for sustainable soil management.Research Limitations: This study relies on existing literature and research, which may have limitations and uncertainties. Further research is needed to address these gaps and enhance understanding.Originality Value: This research enhances the existing knowledge by comprehensively examining the significance of soil pores in carbon dynamics and sequestration. It incorporates both traditional and advanced methods, providing insights for soil management and contributing to climate change mitigation efforts.

Fractional differential systems have received much attention in recent decades likely due to its powerful ability in modeling memory processes, which are mostly observed in real world. Fractional models have been widely investigated and applied in many fields such as physics, biochemistry, electrical engineering, continuum and statistical mechanics. It is shown by many researchers that fractional derivatives can provide more accurate models than integer order derivatives do. Obviously, bang-bang property is of a significant importance in optimal control theory. In this paper a Bang-Bang property and time-optimal control problem for time-Fractional Differential System (FDS) is under consideration. First we formulate our problem and we prove the existence theorem. We state and prove the bang-bang theorem. Finally we give the optimality conditions that characterized the optimal control. Some illustrate applications are given to clarify our results.

The manufacturing parameters influence the properties of thermo-mechanically processed met-als such as Mg alloys. This paper presents how the mechanical properties, the microstructure and the degradation rate of extruded Mn-containing Mg-Gd-alloys can be modified. Gd as repre-sented REE-element is particularly interesting due to the influence on the texture development in Mg and therefore studied as a base alloy system. The contents of Gd were investigated be-tween 2 to 9 wt.% with Mn-addition of 0.5 and 1.0 wt.%. The grain sizes and the corresponding textures were modified by the extrusion parameters and the alloy content. It was shown that modification by Mn can decrease the grain size, but increase the degree of recrystallization and decrease the degradation rate in the biological medium compared to the binary Mg-Gd system from previous studies. The results suggest that the binary Mg-Gd system can be produced more efficiently by adding Mn and that the resulting properties are more robust.

In the present paper, based on the ideas of Algerian physicist M.E. Hassani, the generalized Hassani spatio-temporal transformations in real Hilbert space are introduced. The original transformations, introduced by M.E. Hassani, are the particular cases of the transformations, introduced in this paper. It is proven that the classes of generalized Hassani transforms do not form a group of operators in the general case. Further, using these generalized Hassani transformations as well as the theory of changeable sets and universal kinematics, the mathematically strict models of Hassani kinematics are constructed and the performance of the relativity principle in these models is discussed.

We describe our investigations of the surface physicochemical and biological properties of polylactic acid modified by silver, argon and carbon ion implantation to doses of 1 × 10¹⁴, 1 × 10¹⁵ and 1 × 10¹⁶ ion/cm² at energies of 20 keV (for C and Ar) and 40 keV (for Ag). X-ray analysis shows enhancement of coherent scattering regions and lattice constant increase after ion implantation. Secondary electron mass-spectrometry indicates that Ag concentration in the subsurface layer is less than 80%, but at a depth of 500 nm does not exceed 1–2%. The silver forms metal particles in the subsurface layer rather than making additional chemical bonds with polymer atoms. Atomic force microscopy reveals that the higher the irradiation dose the larger the surface roughness of the samples. Ag-irradiated samples implanted to a dose of 1 × 10¹⁶ ions/cm² have the highest roughness, 190 nm. Our investigation of the cytotoxicity of two individual donor macrophages shows that Ag-implanted polylactic acid has no negative impact on immune system cells and could be a promising material for biomedical application.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

Two desirable functions of healthy soil are nutrient cycling and pest suppression. We review recent literature on the contributions of soil microarthropods to soil health through their intersecting roles in decomposition and nutrient cycling and direct and indirect suppression of plant pests. Microarthropods can impact soil and plant health directly by feeding on pest organisms or serving as alternate prey for larger predatory arthropods, and indirectly, by mediating the ability of crop plants to resist or tolerate insect pests and diseases through interactions with the decomposition food web in support of plant nutrition. Soil fauna, including microarthropods, are key regulators of decomposition at local scales but their role at larger scales is unresolved. Future research priorities include the incorporation of multi-channel omnivory into food web modeling and understanding the vulnerability of our soil carbon to increased global temperatures.

Researches on the runoff and sediment reduction effects of soil and water conservation measures are being on the rise, which is of great significance for carrying out strategic on soil and water conservation in the Yellow River Basin. Through the analysis of various soil and water conserva-tion measures, runoff, sediment, and rainfall datas in the Sanchuan River Basin from 1960 to 2019, we use the lagrange multiplier method to determining the threshold year of soil and water con-servation measures on runoff and sediment processes. The preliminary conclusion is as follows: The trend of flood season rainfall and annual rainfall in the Sanchuan River Basin is consistent. The 10-year average rainfall in each periods indicates that before 2000, it gradually decreased and then significantly increased. The 10-year average runoff showed a gradual decrease before 2010, followed by a sudden increase, while the 10-year average sediment has shown a decreasing trend years by years, especially after the centralized treatment period. Terrace and dam measures show a trend of first decreasing, then increasing, and then approaching stability during different treat-ment periods, while the trend of forest and grass measures is slightly decreasing and then in-creasing rapidly. The runoff and sediment reduction effects of various soil and water conservation measures during different treatment periods indicate that the runoff reduction effect reached its peak in 2005, while the sediment reduction benefit reached its best in 2015. Based on the compre-hensive benefits of runoff and sediment regulation, 2015 are considered as the threshold year for various soil and water conservation measures, with each measure areas being 4.86 × 104, 17.91 × 104, 1.20 × 104, and 0.83 × 104hm2, respectively. The research results will have certain reference significance for the high-quality development of soil and water conservation in the Yellow River Basin.

The objective of this study was to determine how application with dolomitic limestone and grazing type (continuous or deferred) affect sheep grazing location and feed preference when the pasture growth rate is maximum. A 4ha field was divided into 4 plots: P1 and P2- without application of dolomitic limestone, continuous (CG) and deferred grazing (DG), respectively; P3 and P4- with application of dolomitic limestone, DG (1AUE), and CG (2.4 AUE), respectively. In DG, animals were placed and removed from the plots depending on the height of the pasture. In each plot, 12 georeferenced sampling points were identified. Throughout the pasture's vegetative cycle (autumn, winter, spring, and early summer) several measurements of pasture height and cut were carried out. From the beginning of March to the beginning of June, animal behavior was observed, by trained observers, through binoculars on six dates. Animals' activity grazing and location was recorded. The results show that: (i) the application of dolomitic limestone combined with CG provided higher values of pasture height; (ii) there were no significant differences in pasture quality between treatments; (iii) Deferred grazing led to 50% more sheep grazing days than continuous grazing; (iv) there were no significant differences in soil compaction between CG and DG; (v) the type of grazing and the treatment with dolomitic limestone did not seem to change the grazing pattern between treatments. This work contributes to understanding the relationships between different types of grazing in dryland pastures, with and without application of dolomitic limestone, and preferred grazing locations for sheep. This work could help agricultural managers make more informed decisions with the aim of promoting the sustainable intensification of livestock production in the Montado ecosystem.

Background: Across the world, antibiotic resistance is a grave problem. To address this issue, it is necessary to investigate new antibiotic sources. Aim of the study: Egypt's diverse soil habitats were used to produce bacterial Myxopyronin B, which was then tested for antimicrobial activity in preclinical animal studies and randomized human clinical trials stages 1/2. Type of the study: Screening experimental study. Methodology: Egypt's various soil conditions were examined for the development of bacterial isolates that produced the antibiotic compound Myxopyronin B. Reversed phase HPLC was used to purify Myxopyronin B. To determine the test antibiotic's minimum inhibitory concentration( MIC) and invitro antibacterial activity, the Broth microdilution method and the Paper disc diffusion assay were utilized. Moreover, in vivo antibacterial spectrum, adverse medication responses, and pharmacokinetics were found in preclinical animal testing stages and phases 1/2 of randomized clinical studies involving volunteer humans. Results: Myxopyronin B was generated from the culture supernatant of Myxococcus SDU36, the main soil bacterial isolate cultured on a Casein yeast peptone plate. With MICs less than 100 mcg/ml, the test antibiotic prevented the growth of several Gram +ve bacteria, whereas, at MICs higher than 100 mcg/ml, it inhibited the development of a small number of Gram -ve bacteria, including Escherichia coli. However, eukaryotic cells—such as those found in fungi and humans—were unaffected. The test antibiotic was seen to inhibit prokaryotic DNA-dependent RNA polymerase( RNLP), indicating its bactericidal activity. Mean Cmax was 9-10 mcg/ ml at mean Tmax 1 hour when 600 mg dose was orally administered in randomized human clinical trials phases 1/2, and T1/2 reached 2.25 hours following first-order kinetics of elimination. Duration of its action was nearly 8 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and GI upset in less than 7 % of experimental candidates. It exhibited approximately 90% plasma protein binding, especially with albumin which resulted in prolonged therapeutic action. It showed a concentration dependant antibiotic killing effect. With the concentration-dependent killing pattern, the higher the drug concentration relative to the pathogen minimum inhibitory concentration( MIC), the greater the rate and extent of antimicrobial activity. Conclusion: The present study was promising due to the production of the bactericidal antibiotic Myxopyronin B from Myxococcus sp. SDU36 isolated from different soil environments in Egypt.

Background: Antibiotic resistance is an overwhelming serious difficulty globally. This necessitates the exploration of novel sources of antibiotics to overcome this challenge. Aim of the study: Bacterial Myxopyronin A production from various soil environments Egypt; as well as testing its antimicrobial activity in preclinical animal testing and randomized human clinical trials phases 1/2. Type of the study: Screening experimental study. Methodology: Different soil environments in Egypt were screened for the growth of bacterial isolates producing Myxopyronin A as an antimicrobial agent. Purification of Myxopyronin A was performed via reversed-phase HPLC. Paper disc diffusion assay, as well as broth dilution technique, were exploited to assess the invitro antimicrobial and minimum inhibitory concentration( MIC) of the test antibiotic. Furthermore, in vivo antimicrobial spectrum, adverse drug reactions, and pharmacokinetics were detected during animal model testing stages and human randomized clinical trials phases 1/2. Results: From the culture supernatant of the Myxobacterium Myxococcus fulvus 124B02 which was the predominant soil bacterial isolate grown on the Casein yeast peptone plate, Myxopyronin A was produced. The test antibiotic blocked the growth of many Gram +ve bacteria with MICs less than 100 mcg/ ml; whereas it inhibited the growth of a few Gram -ve bacteria such as Escherichia coli at MICs greater than 100 mcg/ ml. On the other hand, Eukaryotic cells such as fungal and human cells were not affected. Prokaryotic DNA-dependant-RNA polymerase( RNLP) was noticed to be inhibited via the test antibiotic suggesting its bactericidal action. Cmax was 7-8 mcg/ ml at Tmax 2 hours when 600 mg dose was orally administered in randomized human clinical trials phases 1/2; as well as T1/2 reached 2.5 hours following first-order kinetics of elimination. The duration of its action was nearly 12 hours after oral administration. Rare toxicity was detected during preclinical and randomized human clinical trials phases 1/2 in the form of mild diarrhea and cholestatic jaundice in less than 5 % of experimental candidates. Conclusion: The present study was promising due to the production of the bactericidal antibiotic Myxopyronin A from Myxococcus fulvus 124B02 isolated from different soil environments in Egypt.

Determining the maturity of compost and other organic fertilizers is very important because of possible phytotoxic or phytostimulative effects. The maturity of the compost can be assessed on the basis of chemical analyses, and the germination test with different test plants is most often used to determine phytotoxicity. In this research, using the results of chemical analyses, the maturity of compost produced from plant residues after maintenance of green public areas was assessed. At the same time, a germination test was carried out with 4 test plant species (cucumber, garden cress, triticale, barley) to determine the phytotoxicity of compost (i.e. compost extract in a ratio of 1:2.5 and 1:10) and 3 ammonium N solutions (in concentrations of 200, 400 and 600 mg/L NH4-N). According to the chemical properties of compost, primarily the C/N and NH4-N/NO3-N ratios, as well as the NH4-N concentration, and the germination test with cu-cumber and garden cress, we can conclude that the tested compost was mature and that we do not expect a phytotoxic effect. The choice of the plant is very significant because the germination test with compost extract shows an undoubted phytostimulative effect on garden cress and cu-cumber with more pronounced phytostimulative effect of compost 1:10 than 1:2.5 extract. No such effect was found on the monocotyledonous test plants triticale and barley since the 1:10 ex-tract had no significant effect, and the 1:2.5 extract had a phytotoxic effect, moderate on triticale and high on barley. The conclusion is that garden cress and cucumber are suitable test plants for determining phytostimulative effect of compost, but they are not suitable for determining phytotoxicity for monocotyledonous plants, especially if the cause of phytotoxicity is some non-ammonium component. Barley is the most suitable species for determining non-ammonium phytotoxicity of compost and phytostimulative or phytotoxic effect of ammonium form of nitrogen. It would be very useful to conduct a comparative germination test with compost extracts in the ratio 1:2.5 and 1:10, whereby the 1:2.5 extract is used as a test for phytotoxicity, and the 1:10 extract for testing phytostimulative effect.

Hybrid organic–inorganic perovskites (HOIPs) are promising materials in several fields related to electronics, offering long carrier-diffusion lengths, high absorption coefficients, tunable band gaps, and long spin lifetimes. Recently, chiral perovskites have attracted a huge interest thanks to the possibility of further widening the applications of HOIPs. Chiral materials, being intrinsically non-centrosymmetric, display several attractive physico-chemical properties, including circular dichroism, circularly polarized photoluminescence, nonlinear optics, ferroelectricity, and spin-related effects. Recent studies have shown that chirality can be transferred from the chiral organic ligands into the inorganic perovskite framework, resulting in materials combining the advantages of both chirality and perovskite superior optoelectronic characteristics. Thus, chiral HOIPs have emerged as promising materials for chiroptoelectronic, spintronic, and ferroelectric applications. Here, we report a summary of the latest advances in the field of chiral HOIPs, with a specific focus on lead-free materials and on the first attempts to understand the correlation between the crystal structure features and the chirality-induced functional properties

The relationship between the street environment and the health, education, mobility, and criminal behaviors of its citizens has long been investigated by economists, sociologists and urban planners. Home buyers were found to pay a premium for better street appearance. Prior studies considering streetscapes mainly focus on objective measures such as the number of nearby trees, the tree canopy area, or the view index of physical features such as greenery, sky or building. However, subjective perceptions may have complex or subtle relationships to physical features, individual physical features or simply summing them up do not capture people’s comprehensive perception. In contrast, this study proposed a new approach for the urban-scale application to quantify both subjectively and objectively measured streetscape scores for six important perception qualities, namely Greenness, Walkability, Safety, Imageability, Enclosure, and Complexity. Built on prior quantitative studies in urban design quality and emerging applications in deep learning and open source street view imagery for urban perceptions, we integrated existing frameworks to (1) effectively collect and evaluate both subjectively and objectively- measured perceptions; (2) investigate the coherence and divergence in ML-predicted subjective scores and formula-derived objective scores; and (3) compare their effects in affecting house prices taking Shanghai as a case study using a large-scale dataset on home transactions. The results implied: first, the percentage increase in sales price attributable to street scores is significant for both subjective and objective measurements. In general subjective scores explained more variance over structural attributes and objective scores in hedonic price model. Particularly, objective Greenness, subjective Safety and Imageability scores positively affected house prices. Second, for Greenness and Imageability scores, the subjective and objective measures exhibited opposite signs in affecting house prices, which implied that there might be mechanisms related to the psychological, social-demographical characteristics of street users that have not been fully incorporated by objective measures that taking view indices or recombination of them. In addition, certain objective measure might outperform subjective counterpart when the connotation of the perception is self-evident and not complicated, for example the Greenness. For those concepts were not familiar to the average person, subjective framework exhibits better performance. This is the first study comprehensively expanding hedonic price method with both subjectively and objectively measured streetscape qualities. It suggested that city authorities could levy a street environment tax to compensate the public budget invested in street environment where developers secured benefits from a price premium. This study enriches our understanding of the economic values of the subjective and objective measures street qualities. It sheds light on promising future study areas where the coherence and divergence of the two measurements should be further stressed.

Mulberry (Morus) cultivated worldwide in diverse agro-ecological conditions recognized as the fodder of silkworms (Bombyx mori). In India, ranging from high altitude Himalayan region to coastal region, the farmers generally cultivate these four species of mulberry (Morus alba, M. indica, M. serrata, and M. laevigata). Mulberry fruit is used in traditional medicine for several years in China and also consumed as food material in different countries of Asia and Africa. Mulberry fruit, along with high nutritious value, contains many bioactive phytochemicals that are30 of health benefits and can fight against many diseases. Many researchers attracted to this property of mulberry fruit, and they isolated bioactive polysaccharides, anthocyanins, flavonols, flavonols, phenolic acids, alkaloids, and melatonins. These compounds have antioxidant property and due to this, either in synergistically or in the pure form, these components have direct or indirect curative activity on diabetes, inflammation, tumor, hepatic diseases, immunomodulation, hyperlipidemia, neural damage, and chronic diseases. This tremendous bioactivity of mulberry fruit extract may open up a new dimension in the food and medicine industry. The present review provides recent findings of the phytochemical foundation and their bioactivities, which may encourage many researchers to explore the molecular mechanism of the biological activities which can be used for human welfare.

Microporous organic polymers (MOPs) are promising materials for gas sorption because of the intrinsic and permanent porosity, designable framework and low density. The introduction of nitrogen-rich building block in MOPs will greatly enhance the gas sorption capacity. Here, we report the synthesis of MOPs from the 2,4,6-tris(4-ethynylphenyl)-1,3,5-triazine unit and aromatic azides linkers via click polymerization reaction. FTIR and solid state 13C CP-MAS NMR confirm the formation of the polymers. CMOP-1 and CMOP-2 exhibit microporous networks with BET surface area of 431 and 406 m2 g-1 and narrow pore size distribution under 1.2 nm. Gas sorption isotherms including CO2 and H2 were measured. CMOP-1 stores superior CO2 level of 8.2 wt% (1.88 mmol g-1) at 273 K/1.0 bar and H2 uptake up to 0.6 wt% at 77 K/1.0 bar, while CMOP-2 with smaller surface area shows lower CO2 adsorption capacity of 7.3 wt% (1.66 mmol g-1) and H2 uptake (0.5 wt%). In addition, I2 vapor adsorption was tested at 353 K. CMOP-1 shows higher gravimetric load of 160 wt%. Despite of the moderate surface area, the CMOPs display excellent sorption ability for CO2 and I2 due to the nitrogen-rich content in the polymers.

Advances in technology and information systems have had a major impact on people's lives and activities. Smartphone use plays an important role in many areas, including housing governance. One of the problems faced by housing administrators is administrative management, which is still manual. To overcome this, it is proposed to use a web-based application. A literature study was conducted to support the development of this application. Data collection through interviews and observations was carried out to obtain system requirements. The Agile Scrum method is used in making applications. These applications have non-functional requirements such as security, availability, performance, usability, and compatibility. Implementation using PHP and MySQL. Testing is done to ensure the application functions properly. This application allows administrators to manage citizen data, payment of contributions, billing, and print financial reports. Residents can upload proof of transfer and print proof of payment. It is hoped that this application will facilitate housing administration, improve the quality of life in the community, and create a better housing environment.

Composite materials are widely used in the dental field in clinics as biomaterials. For example, it has been used as a biomaterial to repair caries and restore masticatory function, and as a cement to adhere the restoration to the tooth substrate. In order to demonstrate its function, dental biomaterials are measured their mechanical strength. From such basic research, we explained the potential of dental biomaterials, especially flexural strength and modulus of elasticity. Mechanical properties of dental biomaterials similar to those of the tooth, thermal stimulation, and aesthetic elements in the oral cavity. In this part, we will introduce the commercialized products of composites suitable for the characteristics and tooth quality, and provide the reader with the characteristics from the flexural characteristics of the composite materials used in clinical dentistry. In clinical performance, it might be advisable to delay polishing when composite biomaterials are used for luting materials, filling materials and core build-up materials since improved the flexural strength and the flexural modulus of elasticity were displayed after 1-day storage. And it is thought that flexural strength or characteristics is a significant important mechanical property of oral biomaterials.

In forests, the microbial populations living in the soil can directly affect the carbon decomposed by the surface plants, and promote carbon storage and stability. In this study, 3 plots of 25.82 m×25.82 m were set up in 5 stand types, respectively. Soil samples were collected from 0~20 cm, 20~40 cm and 40~60 cm layers. Soil microbial composition, organic carbon component, pH, water content, bulk density, nitrogen, phosphorus, potassium and other physicochemical indexes and correlations were determined, and the correlations between soil carbon components and soil microbial functional modules in different mixed modes were analyzed. The results showed that: (1) The SOC of the same soil layer varied significantly, which also showed significant differences on the composition of soil bacteria and fungal microbial communities. Moreover, the bacterial community was more sensitive to the vegetation change environment, and the fungal community structure was more resistant to the influence of soil environment changes. (2) Fun_mod 1,6 and Bac_mod 7 were the microbial functional modules that played a decisive role in the process of soil carbon pool change, and the diversity and composition of bacterial community had more positive effects on soil organic carbon than that of fungal community. (3) Linear fitting and RDA results showed that POC in soil had the strongest correlation with SOC content, indicating that soil microorganisms affected the storage and stability of soil carbon mainly by regulating the conversion of surface plants (carbon sources) into POC. The soil environment of different mixed modes has different effects on soil carbon accumulation. Soil microorganisms affect soil carbon storage and stability mainly by regulating the conversion of surface plants (carbon sources) into POC forms.

.Various synthetic nematicides are currently used effectively in the control of plant parasitic nematodes. However, these nematicides have adverse effects on humans and the environment. Neem oil is eco-friendly alternatives to synthetic nematicides. The effectiveness of repeated neem oil application in suppressing the root-knot nematodes infestation in figs seedlings was therefore examined in this study, both in its natural form (10 ml/L) and in its nano-emulsion form (5 and 7 ml/L). The recorded reduction parameters of M. incognita were J2/250g soil, galls and egg masses / 5g roots of infected fig seedlings were measured at that time, and the effects of these natural additives were compared with the Fosthiazate (Krenkel 75%EC). The impact of such soil amendments on some typical plant parameters, the total microbial count of soil, and the overall enzymatic activity of the fig rhizosphere were also included. Obtained results revealed that the soil population density of root knot nematode suppressed by 80.3% , reduction of nematode egg masses (60.4%) due to the application of nano-emulsion of neem oil (at 7ml/L). Present work recommend the use of nano-emulsion of neem oil as one of the effective and eco-friendly means to reduce the root- knot nematode on fig .

This review examines methodologies studying soil carbon in urban green spaces, a field requiring higher attention as their ecosystem services are valued and urban mitigation plans against climate change are developed. In the growing global urbanization, urban green spaces play a crucial role as nature-based solutions to address climate challenges, demanding efficient carbon accounting and reduction strategies. In this research, a systematic review was conducted assessing publications from 2021 to 2023 in the databases Web of Science and Scopus. Findings expose the lack of standardization in the methodologies used to study soil carbon in urban green spaces, evidencing in situ measurements at different sampling depths and studies without longitudinal monitoring over time. In addition, studies originated primarily in universities from China, United States and Spain, which focused on carbon in the form of Soil Organic Carbon and Total Carbon. Based on these findings, recommendations are made advocating for the combination and standardizing methodologies. This review offers valuable insights that shed light on an ignore and often overseen issue. Further studies and standardized methodology are needed, to help cities efforts in their pursuit of carbon neutrality by acknowledging the influential role of urban soils, especially green spaces.

Faced with increasing climate challenges, this pioneering study introduces groundbreaking approaches to ensure the resilience of potato crops in east-central Poland. Our research aimed to develop an innovative, cost-effective system tailored to the diverse local conditions of this region. Conducted between 2018 and 2020, the study analyzed integrated and organic production systems across different soil types and potato varieties. The experiment was conducted using a randomized block design with three replications in two locations. Integrated practices, enhanced by mineral fertilization and chemical protection, notably delayed the onset of late blight by 16 days and extended the critical infection period by 17% compared to their organic counterparts. Remarkably, the integrated systems resulted in a 49% increase in total production and a 52% increase in commercial yields, demonstrating their effectiveness in enhancing crop resilience. Different potato varieties exhibit varied responses to cultivation systems, influencing both yield and disease resistance. Further investigation into these varietal responses can help optimize cultivation practices, leading to improved efficiency and sustainability in potato farming. Location and soil conditions have a significant impact on potato yield and the spread of potato blight. Further research into specific soil properties and the adaptation of varieties to local conditions can contribute to increased productivity and stability in potato production. This study not only paves the way towards sustainable agriculture but also highlights the crucial role of soil diversity in shaping resilient farming practices.

Towards a better understanding of vegetation, permafrost, climate, landscape and lithology control on major and trace element (including macro and micro-nutrients and toxicants) transport in riverine systems, we studied two medium size (100-150 thousand km² watershed area) pristine rivers (Taz and Ket) of boreal and subarctic zone, western Siberia. Choosing the river basins of very low population density (< 1 people km-²) in the absence of any industrial or agricultural activity allowed testing the sole effect of natural factors and long-range atmospheric transfer on hydrochemistry of riverine solutes during the open water period. In the permafrost-bearing Taz River (main stem and 17 tributaries), sizable control of vegetation on element concentration was revealed. In particular, light coniferous and broadleaf mixed forest controlled DOC, and some nutrients (N, Mn, Fe, Mo, Cd, Ba); deciduous needleleaf forest positively correlated with macronutrients (P, Si, Mg, P, Ca) and Sr, and dark needle-leaf forest impacted Ntot, Al and Rb. Organic C stock in the upper 30-100 cm soil positively correlated with Be, Mn, Co, Mo, Cd, Sb, and Bi. The lithological control was generally poorly pronounced, due to abundant peat deposits overlaying the mineral strata. However, cretaceous carbonate mineral-bearing sedimentary deposits positively impacted the pH and concentration of Si, Mg, Ca and Cs. In the Ket River basin (large right tributary of the Ob River), we revealed the correlations between the phytomass stock at the watershed and alkaline-earth metals and U concentration in the river water. This control was weakly pronounced during high-water period (spring flood) and mostly evidenced during summer low water period.

The use of flexible sensors has tripled over the last decade due to the increased demand in various fields including health monitoring, food packaging, electronic skins and soft robotics. Flexible sensors have the ability to be bent and stretched during use and can still maintain their electrical and mechanical properties. This gives them an advantage over rigid sensors that lose their sensitivity when subject to bending. Advancements in 3D printing have enabled the development of tailored flexible sensors. Various additive manufacturing methods are being used to develop these sensors including inkjet printing, aerosol jet printing, fused deposition modelling, direct ink writing, selective laser melting and others. Hydrogels have gained much attention in the literature due to their self-healing and shape transforming. Self-healing enables the sensor to recover from damages such as cracks and cuts incurred during use and this enables the sensor to have a longer operating life and stability. Various polymers are used as substrates on which the sensing conductive material is placed. Polymers including polydimethylsiloxane (PDMS), polyvinyl acetate (PVA), and Kapton are extensively used in flexible sensors. The most widely used nanomaterials in flexible sensors are carbon and silver, however, other nanomaterials such as iron, copper, manganese dioxide and gold are also used to provide controlled levels of conductivity or other functional properties.

It is well-known that simulation tools are essential for the design and optimization of wireless communication systems. In this paper proposes a python script that can be used for planning and predicting a connection link budget by analyzing its basic parameters. Our proposal consists of an application that calculates the connection budget for point-to-point links operating at 5 GHz, taking into account all the necessary microwave parameters. For validating the efficiency of the proposed tool, the paper presents comprehensive simulation results derived from comparing our tool to a couple of other simulation tools by means of calculating the same parameters.

Lift-offs of the sensor could significantly affect the measurement signal and reconstruction of material properties when using the electromagnetic (inductive) eddy current sensor. Previously, various methods (including novel sensor designs, and features like zero-crossing frequency, lift-off point of intercept) have been used for eliminating the measurement error caused by the lift-off distance effect of the sensor. However, these approaches can only be applied for a small range of lift-off variations. In this paper, a linear relationship has been found between the sensor lift-off and ratio of dual-frequency eddy current signals, particularly under the high working dual frequencies. Based on this linear relationship, the lift-off variation can be reconstructed firstly with a small error of 2.5 % when its actual value is up to 10 mm (10.1 % for 20 mm). The reconstructed lift-off is used to further get the property of the material under a low single frequency. Experiments on different ferrous metals have been carried out for the testing of the reconstruction scheme. Since the inductance is more sensitive to the material property (and less sensitive to the lift-off) under low frequencies, the reconstruction error of the material property is much smaller than that of the lift-off, with 1.4 % under 12 mm (and 4.5 % under 20 mm).

Green manure could improve soil nutrients and crop production, playing a significant role in sustainable agriculture. However, the impacts of green manure on crop health and the roles soil microbial communities play in the process haven’t been clarified clearly yet. In this study, we investigated soil microbial community composition and structure in four tobacco farmlands, which were treated with different green manure (control, ryegrass, pea and rape), using 16S rRNA gene amplicons sequencing. Results showed that green manure had significant impacts on soil properties, microbial communities and tobacco health. First, soil total C, N and Ca content increased significantly in groups treated with green manure than control. Second, soil community diversity was significantly higher in groups treated with green manure. Third, green manure especially ryegrass, decreased tobacco disease (bacterial wilt) rate dramatically, and the process might be mediated by soil microbial communities. On the one hand, several microbial populations were found to be potentially disease inducible or suppressive. For example, the abundances of Dokdonella and Rhodanobacter were positively correlated to tobacco disease rate, while Acidobacteira_Gp4 and Gp6 had negative correlations with tobacco disease. On the other hand, soil microbial communities were shaped by soil properties (e.g., pH, C and N content). In conclusion, our research showed that green manure could increase soil nutrients directly, and further improve tobacco health mediated by soil microorganisms, which may shed light on revealing interactions among soil properties, microorganisms and plants.

Organic fertilizer application in agricultural land is known to improve soil microbial processes, fertility, and yield. In particular, stable changes in soil chemical composition through multi-year fertilization of organic fertilizers are thought to cause changes in the microbial community. Here, the effects of oil cake amendments (OC) on soil bacterial diversity, community profile and enzyme activity were evaluated and compared to those amended with chemical fertilizer (NPK). The comparison of diversity indices between OC and NPK amended soils shows that application of oil cake has increased microbial diversity potentially with an increase in the number of different microbial groups. The ordination plot distinguished and clustered both treatments showing differential effects of soils chemical factors on the microbial communities of each treatment. Proteobacteria, Verrucomicrobia and Bacteriodetes were significantly abundant in OC amended soil than in the NPK received soil, indicating alterations in community structure, composition, and diversity con-current to the changes in pH, Ca and Mg contents of the soil. These shifts in bacterial community structure and composition could also be observed from the phylum to the genus level in both NPK and OC amended soils partially explained by differences in soil chemical factors. The OC soil compared to the NPK amended soil also contain significantly higher abundance of predicted genes corresponding to enzymes related to biogeochemical cycling, decomposition and plant growth promotion. Collectively, these results support the use of an unconventional organic fertilizer positively altering bacterial populations in jujube orchards. The application of oil cake-based organic fertilizer improved microbial diversity and enhanced potential ecosystem functions related to bio-geochemical cycles, mineralization and plant growth promotion.

Enhancing soil fertility and maize productivity is crucial for sustainable agriculture. This study aimed to evaluate the effects of tillage practices, nitrogen management strategies, and acidified hydrochar on soil fertility and maize productivity. The experiment used a randomized complete block design with split-split plot arrangement and four replications. Main plots received shallow tillage and deep tillage. Sub-plots were treated with nitrogen (120 kg ha⁻¹) from farmyard manure and urea, including control, 33% FYM + 67% urea (MU), and 80% FYM + 20% urea (MF). Acidified hydrochar treatments H0 (no hydrochar) and H1 (with hydrochar, 2 t ha⁻¹) were applied to sub-sub plots. Deep tillage significantly increased plant height, biological yield, grain yield, ear length, grains ear-1, thousand grain weight, and nitrogen content compared to shallow tillage. MU and MF improved growth parameters and yield over the control. Hydrochar effects varied; H1 enhanced certain yield components but reduced plant height and soil properties compared to H0. Canonical discriminant analysis linked deep tillage and MU/MF nitrogen management with improved yield and soil characteristics. In conclusion, deep tillage combined with integrated nitrogen manage-ment enhances maize productivity and soil health. However, hydrochar application requires op-timization. These findings highlight the importance of selecting appropriate tillage and nitrogen strategies for sustainable maize production. These insights guide policymakers, agronomists, and agricultural extension services in adopting evidence-based strategies for sustainable agriculture, enhancing food production, and mitigating environmental impacts. Future research should in-vestigate long-term impacts across diverse environments to validate these results.

.Maize cultivation in Thailand faces challenges owing to climate change and soil organic carbon (SOC) loss. This highlights the importance of comparing maize soil with paddy soil in terms of the role of dissolved organic carbon (DOC) and nutrient availability, as they influence SOC content. Soil samples from Chiang Mai province, primarily Fluvisol, were collected for the cultivation of paddy rice and maize, analysed for carbon fractions and chemical properties, and categorised into layers. Comparative analysis revealed that maize soils had lower levels of labile carbon components and organic carbon than paddy soils (P

In Tunisia, olive is the most cultivated fruit crop while in the north where rainfall exceeded 400mm.year-1, the olive growing area is in widely extension in marginal soil with high slope gradient. Thus, the inclusion of cover crops is a sustainable solution to increase the ecosystem productivity, improve the soil fertility and oil yields. But, in Tunisia a few study were investigated the effect of legumes cover crop on the olive productivity. Therefore, the aim of this study was to evaluate the short-term (two cropping seasons s 2021 and 2022) effects of different seeded cover crops and soil management practices on the cover crops and soil characteristics, as well as enzymes activities and related microbial diversity. Six intercropping were tested in rainfed olive orchards (cv.Chétoui): Spontaneous vegetation (Spont), Wheat, Vetch, Oat, Fenugreek, mixture Vetch-Oat and compared to control (3 periodic tillage/year without intercropping). During the first cropping season, cover crops were cut as animal feed and only residues were incorporated into the soil. While, during the second year, all cover crops biomass were incorporated into the soil. Results indicate that the dry biomass and carbon uptake were significantly higher in grasses species (Wheat and Oat). But, highest level of nitrogen was found in Fenugreek cover crops. As compared to control, all cover crops including spontaneous vegetation increased soil organic matter and macronutrient level, mainly phosphorus. The most activity of β-glucosidase, phosphatase and arysulphatase was found in the cover crops plot of wheat and oat. In addition, this study improve that the utilization of the carbon sources was dominated by amides, amine and amino-acids in the fenugreek plot; while it was dominated by polymers and carboxylic acids in the case of wheat and oat.

Molecular dynamics (MD) simulations present a sophisticated nano-scale computational approach that can play a critical role in material design for next generation batteries. One critical piece of information needed for MD simulations is the non-bonded potential parameters, which can be obtained through quantum mechanics (QM) calculations or experimental methods. However, experimental data is not available for exploratory and novel materials to derive the potential parameters. Also, the QM approach needs significant computational power and is too time consuming for large systems. On the other hand, current Artificial Intelligence techniques are faster, but they cannot be generalized across molecules and properties. As a result, there is a significant barrier to discovering and exploring new materials. Overcoming this barrier, in this work, we propose a Machine Learning (ML) based technique that can learn inter-atomic potential parameters for various particle-particle interactions employing QM calculations. This ML model can be used as an alternative for QM calculations for predicting non-bonded interactions in a computationally efficient manner. Using these parameters as input to MD simulations, we can predict a diverse range of properties, enabling researchers to design new and novel materials suitable for various applications in the absence of experimental data. We employ our ML-based technique to learn the Buckingham potential, a non-bonded interatomic potential. Subsequently, we utilize these predicted values to compute the densities of four distinct molecules, achieving an accuracy exceeding 93%. This serves as a strong demonstration of the efficacy of our proposed approach.