The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

Cyanex 301 and LIX 63 can seletively extract Pd(II) over Pt(IV) from strong hydrochloric acid solutions. Therefore, solvent extraction experiments have been performed by extractant mixtures containing either Cyanex 301 or LIX 63 and the extraction behavior of Pd(II) was compared. Among the mixture of Cyanex 301, the highest synergistic enhancement coefficient was achieved by mixing Cyanex 301 and TOPO. However, it was very diffiuclt to strip the Pd(II) from the loaded mixture. Among the mixture of LIX 63, the mixture of LIX 63 and Alamine 336/TOPO enhanced the extraction of Pt(II). Although the synergistic coefficient by Cyanex 301 + TOPO was higher than that by LIX 63 + Alamine 336, the Pd(II) in the loaded mixture of LIX 63 and Alamine 336 was easily stripped by thiourea.

The removal of harmful arsenic(V) from aqueous solutions using Cyanex 923 (solvation extractant) was investigated under various experimental variables: equilibration time, acidity of the aqueous phase, temperature, extractant and arsenic concentrations, and O/A ratio. Cyanex 923 extracted As(V) (and sulphuric acid) from acidic solutions, thus, its use to remove the metal from slightly acid or neutral solutions it is not possible. Extraction of arsenic is exothermic, and responded to the formation of H3AsO4·nL species in the organic phase (L represented the extractant and the stoichiometric factor n: 1 or 2, depends on the acidity of the aqueous phase). Extraction isotherms are derived from experimental results. Both arsenic and sulphuric acid loaded onto the organic phase can be stripped with water, and stripping isotherms are also derived from the experimental results. The selectivity of the system against the presence of other metals (Cu(II), Ni(II), Bi(III), Sb(III)) are investigated, and also it is investigated the ability of Cyanex 923 to extract As(V) and sulphuric acid against the use of other P=O based solvation reagents, such dibutyl butylphosphonate (DBBP) and tri-butyl phosphate (TBP).

Wild strawberry (Fragaria vesca L.) leaves possess diverse antioxidant properties, mainly due to the different classes of phenolics. In this study, microwave-assisted extraction (MAE) and accelerated solvent extraction (ASE) of wild strawberry phenolics were carried out to understand the impact of extraction temperature, extraction time and solvent-to-sample ratio (SSR) on the quantitative and qualitative properties of the obtained extracts. The highest total phenolic content (8027 mg GA/100 g DW), as well the highest DPPH• antiradical activity (903 mol TE/g DW) was obtained with ASE at 150 °C, static time 5 min and SSR of 40:1; while the highest ABTS•+ antiradical activity (681 mol TE/g DW,) and FRAP (2389 mol TE/g DW) was obtained with MAE after 5 min at 80 °C and a SSR of 40:1. The correlation analysis showed that phenolics largely contributed to the antioxidant properties of the studied MAE extracts, while correlation was not found in ASE extracts. A total of 54 different phenolics were identified by UPLC/MS-MS in MAE and ASE extracts obtained at optimal extraction conditions. MAE extract was shown to have a higher content of phenolic acids (40%), but lower content of proanthocyanidins (88%), flavonols (29%), flavan-3-ols (50%) and flavones (39%) than ASE extract.

Lignocellulosic biomass fractionation is typically performed using methods that are somehow harsh to the environment, such as in the case of the kraft pulping. In recent years, the development of new sustainable and environmentally friendly alternatives has grown significantly. Among the developed systems, bio-based solvents emerge as promising alternatives for biomass processing. Therefore, in the present work, the bio-based and renewable chemicals, levulinic acid (LA) and formic acid (FA), were combined to fractionate lignocellulosic waste (i.e., Maritime pine sawdust) and isolate lignin. Different parameters, such as LA/FA ratio, temperature, and extraction time, were optimized to boost the yield and purity of extracted lignin. The LA/FA ratio was found to be crucial regarding the superior lignin extraction from the waste biomass. Moreover, the increase in temperature and extraction time enhances the amount of extracted residue but compromises the lignin purity and reduces its molecular weight. The electron microscopy images revealed that biomass samples suffer significant structural and morphological changes, which further suggests the suitability of the new developed bio-fractionation process. Same was concluded by the FTIR analysis, in which no remaining lignin was detected in the cellulose-rich fraction. Overall, the novel combination of bio-sourced FA and LA has shown to be a very promising system for lignin extraction of high purity from biomass waste, thus contributing to extend the opportunities of lignin manipulation and valorisation into novel added-value biomaterials.

Hexane is a solvent used extensively in the food industry for the extraction of various products such as vegetable oils, fats, flavours, fragrances, colour additives or other bioactive ingredients. As it is classified as a "processing aid", it does not have to be declared on the label under current legislation. Therefore, although traces of hexane may be found in final products, especially in processed products, its presence is not known to consumers. However, hexane, and in particular the n-hexane isomer, has been shown to be neurotoxic to humans and has even been listed as a cause of occupational diseases in several European countries since the 1970s. In order to support the European strategy for a toxic-free environment (and toxic-free food), it seemed important to collect scientific information on this substance by reviewing the available literature. This review contains valuable information on the nature and origin of the solvent hexane, its applications in the food industry, its toxicological evaluation and possible alternatives for the extraction of natural products. Numerous publications have investigated the toxicity of hexane, and several studies have demonstrated the presence of its toxic metabolite 2,5-hexanedione (2,5-HD) in the urine of the general, non-occupationally exposed population. Surprisingly, a tolerable daily intake (TDI) has apparently never been established by any food safety authority. Since hexane residues are undoubtedly found in various foods, it seems more than necessary to clearly assess the risks associated with this hidden exposure. A clear indication on food packaging and better information on the toxicity of hexane could encourage industry to switch towards one of the numerous other alternative extraction methods already developed.

The solvent extraction of gold(III) by undiluted 2-ethylhexanol or dissolved in toluene from HCl solution has been investigated. The numerical analysis of gold distribution data suggests the formation of HAuCl4·L and HAuCl4·2L (L= 2-ethylhexanol) species in the organic phase with formation constants K11= 38 and K12= 309, respectively. The results derived from gold(III) distribution have been implemented in a solid-supported liquid membrane system. The influence of several variables on gold transport was considered: feed and receiving phases stirring speeds, HCl and gold concentrations in the feed phase and carrier concentration in the membrane phase as well as the presence of base metals (Fe,Cu,Ni) and PGMs in the feed phase. Also, diffusional resistances to mass transfer are estimated. Gold is recovered as zero valent nanoparticles.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

Abstract: Agarose is known to form a homogeneous thermoreversible gel in aqueous medium over a critical polymer concentration. The solid-liquid phase transitions are thermoreversible but depend on the molecular structure of the agarose sample tested. Then, in a first step, the structure was characterised by 1H and 13C NMR in D2O and in DMSO which is a solvent of agarose whatever the temperature. A low yield in methyl substituent on the D-galactose unit was determined. Then, evolution of the 1H NMR spectrum was followed as a function of temperature in increasing and decreasing temperature process from 25 to 80°C. A large thermal hysteresis is obtained and discussed. It helps to interpret rheological behaviour. In fact, NMR signals are related to proton relaxation and especially to proton involved in H-bonds between water and -OH agarose for tightly bound water and agarose/agarose in chain packing. In a second step, water was exchanged against ethanol which is a non solvent of agarose. A stable gel was demonstrated and characterised by rheology to be compared with aqueous behaviour. Bound water playing the role of plasticizer is probably removed and the gel is much stronger (and brittle) in ethanol with a larger thermal stability. It is the first time that such gel is characterised without phase transition when passing from a good-solvent to a non-solvent. This extends the domains of application of agarose.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

In this study, the effect of extraction conditions on the total phenolic content of clove buds was investigated. Clove buds were extracted using a deep eutectic solvents like mixtures choline chloride: lactic acid in the 1:2 molar ratio. Additionally, the HPLC-DAD method was used to determine the main components of the clove extracts, including eugenol, eugenol acetate, and β-caryophyllene. The conditions used in the extraction with choline chloride: lactic acid (molar ratio 1:2) included extraction temperature (t = 40 – 80°C), water addition (5.6 – 40%), and extraction time (30 – 90 min). Determination of the phenolic compounds was done by the Folin-Ciocalteu method. The optimum operating conditions for the total phenolic content were identified at 77°C, 30 min, and a water addition of 40%. Based on the results, the highest amount of eugenol (307.26 ± 8,44 mg/g dry raw material) was determined in clove extracts which were extracted under condition of 60°C, 22.8%, and 30 min.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

Dried blood spot (DBS) testing on confetti is one of the most common methods used to collect and extract DNA from field samples for molecular epidemiology of malaria studies. Here, we investigated whether ethanol or other solutions used to clean scissors are a source of sample contamination. DBS were prepared from 3 drops of blood from two Plasmodium falciparum cultures spotted on confetti, and 3 solutions (water, ethanol and DNase) were used to clean scissors between spots during DNA extraction. For each cleaning solution, two blank confetti were used as negative controls. Samples were analyzed by PCR-based genotyping of merozoite surface proteins 1 & 2 (msp-1 and msp-2), and P. falciparum chloroquine resistance transporter (Pfcrt). A total of 15 samples were analyzed. Based on msp-1 and msp-2 amplification, P. falciparum was detected on blank confetti when scissors were washed with ethanol. Based on Pfcrt amplification, DNA of P. falciparum was detected on blank confetti when scissors were cleaned with ethanol or water. No P. falciparum genes were detected on blank confetti when scissors were cleaned with DNase. Scissors cleaned with DNase prevented cross-contamination between samples during processing of dried blood spots, whereas ethanol (which is commonly used) fails to avert cross-contamination.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

The leaves of Nicotiana glauca (Solanaceae) plant, are known for its major cause of health concern. This study investigated the antioxidant activity and polyphenols composition of aerial parts of N.glauca collected from its wild habitat in Jordan, using Methanol-Conventional (MC) and deep eutectic solvents (DESs) extraction methods in addition to nicotine content determination using UHPLC. The results have shown that the MC extract contains fewer total phenols and flavonoid content than the DES extract at ratio of 90% (0.1194 ±0.009 and 0.311± 0.020 mg/mL equivalent to gallic acid) and (0.01084±0.005 and 0.928 ± 0.09 mg/mL equivalent to rutin), respectively. Moreover, the study showed that the MC extract contains 635.07 ppm nicotine compared to the DES extraction method, which contains 1194.91 ppm. Both the MC and the DES extracts exhibited weak antioxidant activities with the highest was 33%inhibition equivalent to ascorbic acid was found for DES at (90%) ratio. The UHPLC-MS/MS analysis revealed the presence of variations in the detected compounds between the two extraction methods used. This study found that en-vironmentally friendly DES extraction of N. glauca produced higher phenol and flavonoid content than MC method, highlighting green chemistry methods' superior efficiency and environmental benefits for extracting valuable phytoconstituents.

This study explores the complexities involved in the extraction and purification of catechins, prominent bioactive compounds found in plant extracts and tea. It addresses challenges arising from the intricate molecular structure of catechins and their inherent variability across botanical sources. Despite these obstacles, catechins present significant potential, particularly in healthcare. Their potent antioxidant properties have been extensively investigated and associated with numerous health benefits, positioning them as promising therapeutic agents for combating chronic diseases. Furthermore, catechins have diverse applications across various industries, including food and beverage, cosmetics, agriculture, and materials science. This abstract emphasizes the importance of continued research and innovation in catechin extraction and utilization, which hold promise for advancing human health and technological progress across multiple domains.

Extraction techniques of important bioactive molecules from the major concern of Seafood byproducts are getting emphasis for better valorization. Employing green extraction technologies for efficient and quality production of these bioactive molecules is also strictly required. Hence, understanding the extraction process parameters to effectively design an applicable optimization strategy could make this real. In this review, statistical optimization strategies applied for the extraction process parameters of bioactive molecules from Seafood byproducts are focused. The type of experimental designs, and techniques applied to criticize and validate the effects of independent variables on the extraction output was addressed. Dominant parameters studied were enzyme/substrate ratio, pH, time, temperature and power of extraction instruments. The yield of bioactive compounds, chitin and chitosan, proteins and peptides, enzymes and carotenoids (Astaxanthins) were the most studied responses. Efficiency and/or economic and quality considerations and their selected optimization strategies that favour the production of potential bioactive molecules were also reviewed.

Dietary polyphenols exist in two forms; extractable polyphenols (EPP) or compounds solubilised by aqueous/organic solvents, and non-extractable polyphenols (NEPP) or compounds remain in the corresponding residues after the extraction. At present, most researchers focus on EEP fractions, while NEPP is neglected. Thus, this study aimed to release NEPP from the remaining powder residue of Barhi date palm kernels (BDPK) with acid hydrolysis. The related extraction conditions were determined and optimised using response surface methodology (RSM) for maximisation of NEPP with highest cytotoxic and antioxidant activities. The face-centred central composite design (FCCCD) was used to establish treatments based on three independent variables, namely; extraction temperature, time, and solvent/sample ratio. Under the optimal conditions, the experimental values for DPPH radical-scavenging capacity of NEPP (IC50=57.52µg/mL), and cytotoxicity of NEPP against A549 and HT29 cells were IC50=17.4 µg/mL and 31.4µg/mL, respectively. The experimental values were in agreement with those predicted by RSM models, confirming the suitability of the model employed and the success of RSM for optimisation of the extraction conditions for NEPP from BDPK. These results indicate that NEPP from industrial date fruit waste could be a promising candidate as natural antioxidants with significant antiproliferation effect against A549 and HT29 cancer cells in-vitro.

Semi-continuous data are very common in the social science and economics. In this paper, a Bayesian variable selection procedure is developed to assess the influence of exogenous factors including observed and unobserved on the semi-continuous data. Our formulation is based on the two-part latent variable model with polytomous response. We consider two schemes for the penalties of regression coefficients and factor loadings: the Bayesian spike and slab bimodal prior and the Bayesian lasso prior. Within the Bayesian framework, we implement Markov Chains Monte Carlo sampling method to conduct posterior inference. To facilitate posterior sampling, we recast the logistic model in part one as the norm-like mixture model. Gibbs sampler is designed to draw observations from the posterior. Our empirical results show that with suitable hyper-parameters, the spike and slab bimodal method slightly outperforms the Bayesian lasso in the current analysis. Finally, a real example related to the China household finance survey is analyzed to illustrate the application of the methodology.. .

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

In order to solve the problem of feature extraction of underwater acoustic signals in complex ocean environment, a new method for feature extraction from ship radiated noise is presented based on empirical mode decomposition theory and permutation entropy. It analyzes the separability for permutation entropies of the intrinsic mode functions of three types of ship radiated noise signals, and discusses the permutation entropy of the intrinsic mode function with the highest energy. In this study, ship radiated noise signals measured from three types of ships are decomposed into a set of intrinsic mode functions with empirical mode decomposition method. Then, the permutation entropies of all intrinsic mode functions are calculated with appropriate parameters. The permutation entropies are obviously different in the intrinsic mode functions with the highest energy, thus, the permutation entropy of the intrinsic mode function with the highest energy is regarded as a new characteristic parameter to extract the feature of ship radiated noise. After that, the characteristic parameters, namely, the energy difference between high and low frequency, permutation entropy, and multi-scale permutation entropy, are compared with the permutation entropy of the intrinsic mode function with the highest energy. It is discovered that the four characteristic parameters are at the same level for similar ships, however, there are differences in the parameters for different types of ships. The results demonstrate that the permutation entropy of the intrinsic mode function with the highest energy is better in separability as the characteristic parameter than the other three parameters by comparing their fluctuation ranges and the average values of the four characteristic parameters. Hence, the feature of ship radiated noise can be extracted efficiently with the method.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

A multiscale model that enables quantitative understanding and prediction of the size effect on scattering properties of micro- and nanostructures is crucial for the design of LED surface textures optimized for high light extraction efficiency (LEE). In this paper, a hybrid process for combining full-wave finite-difference time-domain simulation and a ray-tracing technique based on a bidirectional scattering distribution function model is proposed. We apply this method to study the influence of different pattern sizes of a patterned sapphire substrate on GaN-based LED light extraction from the microscale to the nanoscale. The results show that near-wavelength–scaled patterns with strong diffraction are not expected to enhance LEE. By contrast, microscaled patterns with optical diffusion behavior have the highest LEE at a specific aspect ratio, and subwavelength-scaled patterns that have antireflection properties show marked enhancement of LEE for a wide range of aspect ratios.

Capacitive contact imaging has shown potential in measuring skin properties including hydration, micro relief analysis, as well as solvent penetration measurements. Through calibration we can also measure the absolute permittivity of the skin, and from absolute permittivity we then work out the absolute solvent content in skin. In this paper, we present our latest study of capacitive contact imaging for skin characterizations and vivo skin solvent penetration. We will show how to use capacitive occlusion measurements to characterize skin damages, and how to calculate the absolute water content and solvent content in skin.

A series of novel sulfonylurea benzothiazoline were designed by splicing active groups and bioisosterism. A solvent-free synthetic route was developed for the sulfonylurea benzothiazoline derivatives via the cyclization and carbamylation. All the compounds were characterized by IR, 1H-NMR, 13C-NMR, HRMS. The biological activity tests indicated the compounds could protect maize against the injury caused by chlorsulfuron to some extent. The molecular docking result showed that the new compound competed with chlorosulfuron to bind with the herbicide target enzyme active site to attain detoxification.

Historic expeditions are events that are flavored by exploratory, scientific, military or geographic characteristics. Such events are often documented in literature, journey notes or personal diaries. A typical historic expedition involves multiple site visits and their descriptions contain spatiotemporal and attributive contexts. Expeditions involve movements in space that can be represented by triplet features (location, time and description). However, such features are implicit and innate parts of textual documents. Extracting the geospatial information from these documents requires understanding the contextualized entities in the text. To this end, we developed a semi-automated framework that has multiple Information Retrieval and Natural Language Processing components to extract the spatiotemporal information from a two-volumes historic expedition gazetteer. Our framework has three basic components, namely, the Text Preprocessor, the Gazetteer Processing Machine and the JAPE (Java Annotation Pattern Engine) Transducer. We used the Brazilian Ornithological Gazetteer as an experimental dataset and extracted the spatial and temporal entities from entries that refer to three expeditioners’ site visits and mapped the trajectory of each expedition using the extracted information. Finally, one of the mapped trajectories was manually compared with a historical reference map of that expedition to assess the reliability of our framework. The reference map was manually prepared in previous research work by others.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

This study was designed for the first time to improve phenolic yield and antioxidant activity of ultrasonic-assisted extraction from Acer truncatum leaves (ATL) using response surface methodology, and phenolic composition in ATL extracted under the optimized condition were characterized by UPLC-QTOF-MS/MS. Solvent and extraction time were selected based on preliminary experiments, and a four-factors-three-levels central composite design was conducted to optimize solvent concentration (X₁), material-to-liquid ratio (X₂), ultrasonic temperature (X₃) and power (X₄) for an optimal total phenol yield (Y₁) and DPPH• antioxidant activity (Y₂). The results showed that the optimal combination was ethanol: water (v:v) 66.21%, material-to-liquid ratio 1:15.31 g/mL, ultrasonic temperature 60 °C, power 267.30 W, and time 30 min with three extractions, giving a maximal total phenol yield of 7593.62 mg gallic acid equivalent /100 g d.w. and a maximal DPPH• antioxidant activity of 74241.61 μmol Trolox equivalent/100 g d.w.. Furthermore, 22 phenolics were first identified in ATL extract obtained under the optimized conditions, indicating that gallates, gallotannins, quercetin, myricetin and chlorogenic acid derivatives were the main phenolic composition in ATL. What’s more, a gallotannins pathway existing in ATL from gallic acid to penta-O-galloyl-glucoside was interpreted. All these results provided practical information aiming at full utilization of phenolics in ATL, together with fundamental knowledge for further research.

A possible way to valorize citrus peels, which are byproducts of the juice extraction industry, is to use them as natural biopreservatives. In this paper we present early results from a compared Solvent Free Microwave Extraction (SFME) with Hydro-Distillation (HD) and Cold Pressing (CP) of essential oils (EOs) using fresh orange peel (Citrus sinensis L. var. Valencia late), a by-product in the production of orange juice in Algeria. The EOs were analyzed by gas chromatography coupled to mass spectrometry (GC-MS). All extracted C. sinensis EOs were chemotype limonene (94.64 to 95.48%). SFME is performed without added any solvent or water. SFME increases EO yield and eliminate wastewater treatment, resulting in a great progress in terms of time and cost efficiency. In its second part, the present study was conducted to evaluate “in vitro”, the antioxidant activities of Solvent Free Microwave (SFM) extracted orange EO by using the DPPH• (2,2-di-phenyl-1-picrilhydrazyl) free radical scavenging assay. The ability of orange EO to scavenge the free radical DPPH• was high, exceeding 80%. The result of the DPPH assay gives an IC₅₀ range value of 89.25 μg/mL (0.09 mg/mL) for the studied sample. Accordingly to the scientific literature, C. sinensis EO tested in the present study presented strong antioxidant activity, when looking to its values of AAI = 1.12 μg/mL. The feasibility of biopreservation used EOs as an alternative to synthetic techniques for liquid whole egg (LWE) stored under commercial retail conditions was investigated. The orange EO extracted by SFM was screened for its antibacterial and antioxidant activities in LWE at concentrations of 0.1, 0.3 and 0.5%. The TBA-RS results showed that the EO treatments significantly (p < 0.05) reduced the lipid oxidation in LWE. The long term oxidative, microbial and organoleptical stability of the LWE during display was positively influenced by orange EO treatments. Therefore, the results obtained here confirm that EO treatment as a promising technology to extend the commercial shelf-life of liquid egg products during retail/display.

The application of solvent method in the preparation of polypropylene powders was investigated, including the influence of various technological conditions, such as the raw material melt index of polypropylene, processing temperature, dosage of the solvent and the packing pressure. The experimental data show that using solvent method can effectively produce polypropylene powder, and the optimal technological conditions are: melt index of polypropylene being about 17.8 g/10min, processing temperature being about 166.0 ℃, dosage of the solvent being about 0.067g/ml and the packing pressure being about 0.7MPa.Under this technological conditions, polypropylene powder with excellent sphericity could be prepared, the apparent density of powder can reach 0.40 g/cm3 and the prepared powder displayed a narrow size distribution with the mean size of about 42.7 µm.

Furfuryl alcohol (FA) is a biobased monomer derived from lignocellulosic biomass. The present work describes its polymerization in presence of protic polar solvents, i.e. water or isopropyl alcohol (IPA), using maleic anhydride (MA) as acidic initiator. The polymerization was followed from the liquid to the rubbery state by combining DSC and DMA data. In the liquid state, IPA disrupts the expected reactions during all the FA polymerization due to a stabilization of the furfuryl carbenium center. This causes the initiation of the polymerization at higher temperature, which is also reflected by higher activation energy. In water system, the MA opening allows to start the reaction at lower temperature. A higher pre-exponential factor value is obtained in that case. The DMA study of final branching reaction occurring in the rubbery state has highlighted continuous increase of elastic modulus until 290 °C. This increasing tendency of modulus was exploited to obtain activation energy dependences (Eα) of FA polymerization in the rubbery state.

Cannabis is a flowering plant that has long been used for medicinal, therapeutic, and recreational purposes. Cannabis contains more than 500 different compounds, including a unique class of terpeno-phenolic compounds known as cannabinoids; Δ9-tetrahydrocannabinol (THC) and cannabidiol (CBD) are the most prevalent cannabinoids and have been associated with the therapeutic and medicinal properties of the cannabis plant. In this paper, continuous flow microwave assisted extraction (MAE) is presented and compared with other methods for commercial cannabis extraction. The practical issues of each extraction method are discussed. The main advantages of MAE are: continuous-flow method which allows for higher volumes of biomass to be processed in less time than existing extraction methods, improved extraction efficiency leading to increased final product yields, improved extract consistency and quality because the process does not require stopping and restarting material flows, and ease of scale-up to industrial scale without the use of pressurised batch vessels. Moreover, due to the flexibility of changing the operation conditions, MAE eliminates additional steps required in most extraction methods, such as biomass decarboxylation, winterisation, which typically adds at least a half day to the extraction process. Another factor that sets MAE apart is the ability to achieve high extraction efficiency even at the industrial scale. Whereas the typical recovery of active compounds using supercritical CO¬2 remains around 70-80%, via MAE up to 95% of the active compounds from cannabis biomass can be recovered at the industrial scale.

This study reports a general scenario for the out-of-equilibrium features of collapsing polymeric architectures. We use molecular dynamics simulations to characterize the coarsening kinetics, in bad solvent, for several macromolecular systems with an increasing degree of structural complexity. In particular, we focus on: flexible and semiflexible polymer chains, star polymers with 3 and 12 arms, and microgels with both ordered and disordered networks. Starting from a powerful analogy with critical phenomena, we construct a density field representation that removes fast fluctuations and provides a consistent characterization of the domain growth. Our results indicate that the coarsening kinetics presents a scaling behaviour that is independent of the solvent quality parameter, in analogy to time-temperature superposition principle. Interestingly, the domain growth in time follows a power-law behaviour that is approximately independent of the architecture for all the flexible systems; while it is steeper for the semiflexible chains. Nevertheless, the fractal nature of the dense regions emerging during the collapse exhibits the same scaling behaviour for all the macromolecules. This, suggests that the faster growing length scale in the semiflexible chains originates just from a faster mass diffusion along the chain contour, induced by the local stiffness. The decay of the dynamic correlations displays scaling behavior with the growing length scale of the system, which is a characteristic signature in coarsening phenomena.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

Demand for nutmeg essential oil in Indonesia and the world is increasing. Nutmeg essential oil is obtained from young nutmeg seeds extracted by water steam distillation (WSD). The weakness of the extraction process with WSD is the long distillation time (24 hours), wasteful of fuel, wasteful of manpower, produces polluting gases which damage the environment and requires a lot of water as a coolant. The purpose of this study was to compare the WSD and SCFE methods for extracting nutmeg essential oil. The research was conducted by extracting nutmeg essential oil using two methods are WSD and SCFE. The results showed that the chemical composition of the nutmeg essential oil produced by the two methods was almost similar. Nutmeg essential oil produced by both methods shows the same characterization. The yield between the two methods is almost the same, in the range of 10-12% using extraction time 15-60 minutes. The SCFE method has advantages over WSD are a faster extraction time, does not require heating materials and CO2 gas can be reused. In conclusion, SCFE is an alternative method to increase the production of nutmeg oil.

Cycling reliability is crucial for Si-based materials due to severe volume change during cycles that results in the fast capacity fading. Though the binder only occupies a very low amount of the total mass of anodes, it is proved to perform a key parameter to improve the cycle performance of Si-based anodes. Because they are eco-friendly and cost saving, water-based binders styrene-butadiene rubber (SBR) and carboxymethyl cellulose (CMC) are regarded as the better binder to substitute Poly (vinylidene difluoride) (PVDF) as the binder for Si-based anode. In this study, the anodes are fabricated by simply mixing the active materials (naso Si, graphite and conductive additive) together and using the mixture of SBR and CMC as a binder. The results showed that the retention capacities of the anodes are more than 440 mAh/g after 400 cycles. It indicates that it is an easy and simple way to make high performance anodes.

A sustainable green one pot procedure for the synthesis of dihydropyrimidinones (DHPMs) derivatives by a three-component reaction of β-ketoester derivatives, aldehyde and urea or thiourea over the alkali-treated H-ZSM-5 zeolite under ball-milling has been developed. The product was isolated by simple washing of the crude reaction residue with ethyl acetate followed by evaporation of solvent. The hierachical zeolite catalyst (MFI27_6) showed high yield (86–96%) of dihydropyrimidinones (DHPMs), in very short time (10-30 min). The catalyst is recycled for subsequent reactions in four runs without appreciable loss of activity and high yields of products provide efficient protocol for Biginelli reactions.

A simple and eco-friendly Montmorillonite K10 (MK10) catalyzed method for the synthesis of cyclopentenone derivatives from biomass-produced furfural has been developed. The versatility of this protocol is that the reactions were carried out in solvent free condition and in short reaction time under heterogeneous catalysis. Montmorillonite K10 is a material most explored as heterogeneous catalyst since it is inexpensive and environmentally friendly.

The number of documents published on the Web other languages than English grows every year. As a consequence, it increases the necessity of extracting useful information from different languages, pointing out the importance of researching Open Information Extraction (OIE) techniques. Different OIE methods have been dealing with features from a unique language. On the other hand, few approaches tackle multilingual aspects. In such approaches, multilingual is only treated as an extraction method, which results in low precision due to the use of general rules. Multilingual methods have been applied to a vast amount of problems in Natural Language Processing achieving satisfactory results and demonstrating that knowledge acquisition for a language can be transferred to other languages to improve the quality of the facts extracted. We state that a multilingual approach can enhance OIE methods, being ideal to evaluate and compare OIE systems, and as a consequence, to applying it to the collected facts. In this work, we discuss how the transfer knowledge between languages can increase the acquisition from multilingual approaches. We provide a roadmap of the Multilingual Open IE area concerning the state of the art studies. Additionally, we evaluate the transfer of knowledge to improve the quality of the facts extracted in each language. Moreover, we discuss the importance of a parallel corpus to evaluate and compare multilingual systems.

Background: A new access technique was developed to reduce postoperative adverse events after the extraction of impacted maxillary wisdom teeth. Hence, this study aimed to assess the occurrence of adverse events after extraction of maxillary impacted wisdom teeth using traditional or modified access. Methods: Two different surgical incision designs were used for bilateral wisdom tooth extractions in 30 patients. The traditional incision was performed distal to the second molar in the center of the tuberosity, followed by a buccal releasing incision. After tooth extraction the wound was secured by sutures. The new technique consists of an oblique incision from the distal palatal aspect of the tuberosity towards the buccal aspect of the second molar. After tooth extraction, cyanoacrylate glue was used on the wound. Results: Lower pain was reported by patients at the site treated with the new technique (p&lt;0.01). Edema, postsurgical bleeding, and hematoma were similar in both groups. The surgical time was shorter for the new technique (p&lt;0.01). Conclusions: The new technique applied for the extraction of impacted maxillary wisdom teeth reduced postsurgical pain and the duration of surgery.

In this work we explored how solvents can affect olefin oxidation reactions catalyzed by MCM-bpy-Mo catalysts and whether their control can be made with those players. The results of this study evidenced that polar and apolar aprotic solvents modulated the reactions in different ways. Experimental data showed that acetonitrile (aprotic polar) could hinder largely the reaction rate whereas toluene (aprotic apolar) did not. In both cases product selectivity at isoconversion was not affected. Further insights were obtained by means of neutron diffraction experiments, which confirmed the kinetic data allowing to propose a model based on substrate-solvent crosstalk by means of hydrogen bonding. In addition, the model was also validated in the ring-opening reaction (overoxidation) of styrene oxide towards benzaldehyde, which progressed when toluene was the solvent (reaching 31% styrene oxide conversion) but was strongly hindered when acetonitrile was used instead (reaching only 7% conversion), due to the establishment of H-bonds in the latter. Although this model was confirmed and validated for olefin oxidation reactions, it can be envisaged that it may also be applied to other catalytic reaction systems where reaction control is critical, while widening its use.

In this paper we review dynamics and roughness of bonds in proteins on example of albumin, that is important from the physiological point of view. We have performed computer simulations of albumin chain. Statistics were collected by performing many simulations realizations for each experimental setting. We concentrate on hydrogen bonds, cation-π and π- π interactions and NP contacts. Histograms of hydrogen bonds length are positively skewed in contrary to histograms of interactions and HP contacts that are negatively skewed. Scaling exponents of power spectra of energies of bonds / interactions /contacts are in range -0.2 to -0.5 and significantly differ between various hydrogen bonds or interactions. Varying scaling of such spectra can be used to classify between distinct bonds or contacts. Concerning particular amino-acids, largest amount of HBO H20 bonds are between Glutamate (GLU) amino-acids and water particle, while large amount of HBO bonds are formed with Lysine (LYS). For HP contacts the mayor role plays Phenylalanine (PHE) and Leucine (LEU) amino-acids. From decay curves HBO H2O bonds decays in fastest rate, while HBO bonds and HP contacts at slowest rate. We present as well decay curves of bonds formed by particular amino-acids, that gives interesting results.

Reactions of Fe(II) with the tris-(pyridin-2-yl)ethoxymethane (py3C-OEt) tripodal ligand in presence of the pseudohalide ancillary NCE- (E = S, Se, BH3) ligands led to a series of three mononuclear complexes formulated as [Fe(py3C-OEt)2][Fe(py3C-OEt)(NCE)3]2·2CH3CN, with E = S (1), BH3 (2) and Se (3). Single crystal characterizations (complexes 1-2) and X-ray powder diffraction (complexes 1-3) reveal monomeric isomorph structures formed by the spin crossover (SCO) anionic [Fe(py3C-OEt)(NCE)3] complex, associated with the low spin (LS) cationic [Fe(py3C-OEt)2]2+ complex and two solvent acetonitrile molecules. In the [Fe(py3C-OEt)2]2+ cation, the Fe(II) is coordinated by two py3C-OEt tridentate ligands, while the [Fe(py3C-OEt)(NCE)3] anion displays a hexacoordinated environment involving three N-donor atoms of one py3C-OEt ligand and three nitrogen atoms arising from of the three (NCE) coligands. The magnetic studies show the presence of gradual SCO behavior for the three complexes: a one-step transition around 205 K for 1 and two step-transitions for compounds 2 and 3, centred at 245 K and 380 K for 2, and at 170 K and 298 K for 3. The magnetic behaviors of complexes 1 and 2 remain unchanged when heating up to 500 K, while complex 3 shows significant changes which are caused by the crystallisation solvent loss above room temperature.

The exploitation and use of alternative synthetic methods, in the face of classical procedures that do not conform to the ethics of Green Chemistry, represent an ever present problem in pharmaceutical industry. The procedures for the synthesis of benzimidazoles have become a focus in synthetic organic chemistry, as they are building blocks of strong interest for the development of compounds with pharmacological activity. Various benzimidazole derivatives exhibit important activities such as antimicrobial, antiviral, anti-inflammatory and analgesic and some of the already synthesized compounds have found very strong application in medicine praxis. Here we report a selective and sustainable method for the synthesis of 1,2-disubstituted or 2-substituted benzimidazoles, starting from o-phenylenediamine in the presence of different aldehydes. The use of deep eutectic solvent (DES) both as reaction medium and reagent without any external solvent provides advantages in terms of yields as well as in the work up procedure of the reaction.

Natural carotenoids are secondary metabolites that exhibit antioxidant, anti-inflammatory and anti-cancer properties. These types of compounds are in high demand by pharmaceutical, cosmetic, textile and food industries, leading to the search for new natural sources of carotenoids. In recent years, the production of carotenoids from bacteria has become of great interest for industrial applications. In addition to carotenoids with C40-skeletons, some bacteria have the ability to synthesize characteristic carotenoids with C30-skeletons. In this regard, a great variety of methodologies for the extraction and identification of bacterial carotenoids has been reported and this is the first review that condenses much of this information. To understand the diversity of these carotenoids, we present their biosynthetic origin in order to focus on the methodologies employed in their extraction and characterization. Special emphasis has been made on high-performance liquid chromatography-mass spectrometry (HPLC-MS) for the analysis and identification of bacterial carotenoids. We end up this review showing their potential commercial use of bacterial carotenoids. This review is proposed as a guide for the identification of these metabolites, which are frequently reported in new bacteria strains.

A study has been carried out on Ta and Nb recovery by liquid-liquid extraction process using 4-methylacetophenone (4-MAcPh) as organic phase. The 4-MAcPh was compared to methylisobutylketone (MIBK) with respect to extraction efficiencies (kD values) at different concentrations of H2SO4 in the aqueous phase. The results showed a similar extraction of Nb for both solvents. However, for Ta extraction efficiency is increased by a factor of 1.3 for 4-MAcPh. In addition, the MIBK solubilized completely after 6 mol L-1 of H2SO4 against only a loss of 0.14 to 4% for 4-MAcPh between 6 and 9 mol L-1 of H2SO4. The potential of 4-MAcPh has also been studied to selectively recover Ta from a model capacitor waste solution. The results showed a selectivity for Ta in the presence of impurities such as Fe, Ni, Mn. The 4-MAcPh also presents the advantage of having physicochemical properties adapted to its use in liquid-liquid extraction technologies such as mixer-settlers.

This paper provides orthogonal moments (OM) such as, Zernike Moments(ZM), Psuedo Zernike Moments(PZM) and Orthogonal Fourier Mellin Moments(OFMM) for the analysis of melanoma images. The moment invariants may vary with respect to geometric variations. For the analysis of orthogonal moments hundred random melanoma images and hundred non-melanoma images have been taken into consideration from the database of 570 melanoma images and 250 non-melanoma images respectively. Orthoganal moments have been computed by varying the phase angles from 10° to 40° with an equal interval of 10° degree for the orders 2, 4,8,16,32,64,128,256 respectively. For the optimal OMs Particle Swarm Optimization (PSO) technique have been used. These set of extracted optimal OMs have been further applied to classify melanoma images. Support Vector Machine (SVM) has been used for the classification of [1]sensitivity=88.78%.

Sports video analysis is an interesting and emerging field in the domain of computer vision. It has become a very popular subject among scholars all over the world in the last decade due to the need of automated classification of events such as offsides, in/out situations, goals and so on. The most important problem in sports video analysis is detection and tracking of ball and players. Extraction of court lines is also another important problem since it is necessary in the classification of aforementioned events. In this study, considering some of the previous work on the subject, we develop a method for tracking the ball and players in tennis videos where the camera position and orientation is supposed fixed.

In the present work, a novel and the robust computational investigation is carried out to estimate solubility of different acids in supercritical carbon dioxide. Four different algorithms such as radial basis function artificial neural network, Multi-layer Perceptron (MLP) artificial neural network (ANN), Least squares support vector machine (LSSVM) and adaptive neuro-fuzzy inference system (ANFIS) are developed to predict the solubility of different acids in carbon dioxide based on the temperature, pressure, hydrogen number, carbon number, molecular weight, and acid dissociation constant of acid. In the purpose of best evaluation of proposed models, different graphical and statistical analyses and also a novel sensitivity analysis are carried out. The present study proposed the great manners for best acid solubility estimation in supercritical carbon dioxide, which can be helpful for engineers and chemists to predict operational conditions in industries.

Polyamides (PAs) are one of the most important engineering polymers; however, the difficulty in dissolving them hinders their applications. Formic acid (FA) is the most common solvent for PAs, but it has industrial limitations. In this contribution, we proposed a new solvent system for PAs by replacing a portion of the FA with urea and calcium chloride (FAUCa). Urea imparts the hydrogen bonding and calcium ion from the calcium chloride, as a Lewis acid was added to the system to compensate for the pH decrease due to the addition of urea. The results showed that the proposed solvent (FAUCa) could readily dissolve PAs, resulting in less decrease in the mechanical properties during the dissolution. The composite prepared using the FAUCa has almost the same properties like the one prepared using the FA solution. The solution was applied on a polyamide 66 fabric to make an all-polyamide composite coated-fabric, which then was characterized. The FAUCa solution had a higher viscosity than the one prepared using the neat FA solvent, which can be an advantage in the applications which needs higher viscosity like preparing the all-polyamide composite coated-fabric. A more viscouse solution makes a denser coating which will increase the water-/gas-tightness. In conclusion, using the FAUCa solvent has two merits: 1. replacement of 40 % of the FA with less harmful and environmentally-friendly chemicals and 2. enabling for the preparation of more viscouse solutions, which makes denser coating.

Industrial hemp (Cannabis sativa L.) is an attractive candidate for sustainable pest management due to its abundance of bioactive compounds with potential pesticidal properties. Solvent choice has a significant impact on the extraction efficiency of bioactive compounds. Deep Eutectic Solvents (DESs) are gaining popularity in extraction because they are safe and environmentally friendly, making them viable alternatives to organic solvents (OSs). This research first compared the extraction efficiency of OSs on the extraction of phytochemicals from the infloresences of two hemp varieties, Citrus and Cherry Dwarf. Inflorescences were extracted using three OSs, ethanol, ethyl acetate, and hexane. The highest level of cannabidiol (CBD; 0.69%) was extracted from Cherry Dwarf using ethanol while the level of delta-9 tetrahydrocannabinol THC (0.19%) was essentially the same in both. Therefore, Cherry Dwarf was selected to compare the extraction efficiency of DESs to the OSs. The DESs were choline chloride/ethylene glycol, citric acid/ethylene glycol, menthol/lauric acid, choline chloride/urea and choline chloride/glycerol. In the targeted analysis, choline chloride/ethylene glycol extracted the highest amount of CBD (0.87%) followed by choline chloride/urea (0.78%). As some DESs outperformed ethanol, the popular solvent for extracting cannabinoids, DESs are viable candidates to replace organic solvents.

The ability of thermoresponsive polymers to respond to temperature with a reversible conformational change makes them promising ‘smart’ materials for solutions in medical and biotechnological applications. In this work, two such polymers and structural isomers were studied: poly(N-isopropyl acrylamide) (PNiPAm) and poly(2-isopropyl-2-oxazoline) (PiPOx). We compare the critical solution temperatures (CST) of these polymers in D2O and H2O in the presence of Hofmeister series salts, as results obtained under these different solvent conditions are often compared. D2O has a higher dipole moment and electronegativity than H2O, which could significantly alter the CST transition. We used two complementary methods to measure the CST, dynamic light scattering (DLS) and differential scanning calorimetry (DSC), and found that the CST decreased significantly in D2O compared to H2O. In the presence of highly concentrated kosmotropes, the CST of both polymers decreased in both solvents. The influence of the kosmotropic anions was smaller than the water isotope effect at low ionic strengths but considerably higher at physiological ionic strengths. However, the Hofmeister anion effect was quantitatively different in H2O than in D2O, with the largest relative differences observed for Cl-, where the CSTs in D2O decreased more than in H2O measured by DLS but less by DSC. PiPOx was more sensitive than PNiPAm to the presence of chaotropes. It exhibited much higher transition enthalpies and multistep transitions, especially in aqueous solutions. Our results highlight that measurements of thermoresponsive polymer properties in D2O cannot be compared directly or quantitatively to application conditions or even measurements performed in H2O.

Research has shown that the consumption of herbal teas is linked with positive effects on the regulation of postprandial blood glucose level. In this study, a comparative analysis of aqueous and ethanol extractions is performed on four herbal teas (Mallotus, Cyclocarya, Rubus, Vine) to evaluate their phytochemical profiles and functional activities. Investigations of phytochemical contents, antioxidant activities, α-glucosidase inhibitory activities and chemical compositions are carried out through colorimetric analyses and UPLC-Q-Orbitrap HRMS/MS, respectively. Results showed that among the studied herbal teas, Vine exhibited the highest glucose re-gulating abilities under both aqueous and ethanol extractions. Overall, ethanol extracted samples yielded higher phytochemicals content, but the compositions of the phytochemicals varied. Meanwhile, aqueous extracts showed surprisingly strong antioxidant activities and comparable α-glucosidase inhibitory activities with ethanol extracts. Phytochemicals contents presented a positive correlation with antioxidant activities and α-glucosidase inhibitory activities. Nevertheless, antioxidant activities displayed a weak positive correlation with α-glucosidase inhibitory activities. Results from this study provided evidence that aqueous extracts from herbal teas possessed valuable phytochemicals composition for antioxidants and the hyperglycemic populations, and are promising candidates for potential applications as functional ingredients with health promoting effects and as natural additives to boost the nutritional value of herbal food products.

Melanins are phenolic biopolymers synthesised by most of the living organism mainly for photoprotection or surviving in harsh conditions. Melanin is localised in different areas or complexed with different other biomolecules when observed from animals to microbes. This makes the melanin extraction procedure different in animal, plant and microbial tissues. Basically, the alkali-acid extraction is used in most protocols of which slight variations are there depending on the tissue used. This review will try to compile melanin extraction procedures from different cells and tissues ranging from animals to bacteria.

(1) Background: Tooth extraction is one of the oldest and most well-known surgical procedures in dental medicine. It is still routinely performed to date by both general practitioners, oral surgeons, and dental undergraduates. The Benex extraction system allows for the extraction of teeth in vertical direction, which avoids most trauma against the surrounding alveolar bone and soft tissues; (2) Methods: The study included 56 patients who were recruited from the department of Oral Surgery at the Faculty of Dental Medicine, Medical University – Plovdiv. Patients were divided into two groups of 28 patients – Group I (control group) and Group II (study group). For each group the success of the extraction, buccal cortical plate preservation, pain experience and early wound healing were assessed; (3) Results: There was no statistical significance between the success of the extractions in both groups. The Benex extractions preserved the buccal cortical plate in 95% of the cases, whereas the forceps extractions only in 71.8%, which shows a statistical significance. On the seventh day patients in group II reported less pain, without a significant difference. There was a significantly bigger number of completely healed extraction wounds on the 10th day; (4) Conclusions: Atraumatic extractions allow for more hard and soft tissues to be preserved in the extraction site. This is all crucial for the successful outcome and aesthetically pleasing results of a following prosthetic or implant restoration.

Sweet cherry pomace is a by-product that can be a source of bioactive phenolic compounds. Usually, polyphenols have been extracted using conventional extraction methodologies. However, a significant fraction, called non-extractable polyphenols (NEPs), remains retained in the conventional extraction residues. Therefore, this work is aimed, for the first time, to investigate the release of NEPs from cherry pomace combining pressurized liquid extraction (PLE) and enzyme-assisted extraction (EAE) using Promod enzyme. A response surface methodology was employed to study the influence of temperature, time, and pH on the NEPs extraction. The response variables were the total phenolic content (TPC) measured by Folin-Ciocalteu method, total proanthocyanidin (PA) content evaluated by vanillin, DMAC, and butanol/HCl assays, and total antioxidant capacity determined by Trolox equivalent antioxidant capacity and inhibition of hydroxyl radical assays. The results indicated that PLE-EAE was more suitable and selective to obtain NEPs from sweet cherry pomace than PLE alone. In fact, the extracts obtained by PLE-EAE displayed higher TPC, PA content, and bioactivity than the extracts obtained by PLE under the same extraction conditions, and those obtained by conventional methods. Moreover, size-exclusion chromatography profiles showed that the combination of PLE and EAE enabled the recovery of NEPs with higher molecular weight than PLE without EAE treatment.

This review provides a systematic analysis of the literature data on the electrodeposition of composite coatings using plating baths based on a new generation of room-temperature ionic liquids, known as deep eutectic solvents (DESs). Such systems offer several advantages over traditionally used aqueous electrolytes and organic solvent-based electrolytes. The colloidal-chemical properties of suspension and colloidal electrolytes for composite deposition are thoroughly examined. New theories describing the kinetics of co-deposition of composite layers are characterized. The kinetics and mechanism of electrochemical deposition processes of composite coatings with metallic matrices are discussed. Case studies regarding the electrodeposition of composite coatings based on electrodeposited copper, silver, zinc, tin, nickel, cobalt, and chromium from DES-assisted electroplating baths are described and systematized. The main prospective directions for further research in the discussed scientific area are highlighted.

The power conversion efficiency (PCE) of polymer solar cells (PSCs) are strongly depended on the bulk-heterojunction active layer. Here, the 1,8-diiodooctane (DIO) additives have been added into the PCDTBT: PC70BM blend PSCs. Based on the higher boiling point than host solvent ODB and better solubility of PC71BM, the device photovoltaic properties with DIO additive were changed obviously. The investigations of EQE indicate that the DIO can influence the charge recombination and transportation process, and absorption studies demonstrate that the charge carriers generation process can also be affected by DIO. The overall impact reflected on the decreased equivalent resistant. With 3% v/v DIO, the Jsc, Voc and FF are both increased. Correspondingly, a highest PCE is achieved of 6.15%, while the reference device without DIO only has a PCE of 5.23%. Hence, adding DIO solvent additive is a effective method for the photovoltaic properties improving of PCDTBT: PC70BM blend PSCs.

We report herein the synthesis of siloxane-functionalized CBP molecules (4,4’-bis(carbazole)-1,1′-biphenyl) for liquid optoelectronic applications. The room-temperature liquid state is obtained through a convenient functionalization of the molecules with heptamethyltrisiloxane chains via hydrosilylation of alkenyl spacers. The synthesis comprises screening of metal-catalyzed methodologies to introduce alkenyl linkers into carbazoles (Stille and Suzuki Miyaura cross-couplings), incorporate the alkenylcarbazoles to dihalobiphenyls (Ullmann coupling), and finally introduce the siloxane chains. The used conditions allowed the synthesis of the target compounds, despite the high reactivity of the alkenyl moieties bound to π-conjugated systems toward undesired side reactions such as polymerization, isomerization, and hydrogenation. The features of these solvent-free liquid CBP derivatives make them potentially interesting for fluidic optoelectronic applications.

Ferulic acid esters have been suggested as a group of natural chemicals with sunscreen function. The study aimed to utilize an environment-friendly enzymatic method to produce octyl ferulate by esterification of ferulic acid with octanol. The Box-Behnken design with response surface methodology (RSM) was adopted to evaluate the effects of synthesis variables, including reaction temperature (70–90 °C), enzyme amount (1000–2000 PLU) and stir speed (50–150 rpm), on the molar conversion of octyl ferulate. According to the joint test, both the reaction temperature and enzyme amount had great impacts on the molar conversion. RSM-developed second-order polynomial equation further showed great ability on data-fitting. Based on ridge max analysis, the optimum parameters for the biocatalyzed reaction were: 72 h reaction time, 92.2 °C reaction temperature, 1831 PLU enzyme amount and 92.4 rpm stir speed, respectively. Finally, the molar conversion of octyl ferulate under optimum condition was verified to be 93.2 ± 1.5%. In conclusion, high yield of octyl ferulate synthesized by commercial immobilized lipase under elevated temperature conditions has been suggested, which our findings could broaden the utilization of the lipase and provide a biocatalytic approach, instead of the chemical method, for ferulic acid ester synthesis.

Soil nitrite (NO2‒) is an important reactive intermediate in many nitrogen transformation processes, but it is unstable under acidic conditions. Canonical extraction method of soil NO2‒ with potassium chloride (KCl) solution greatly underestimates its concentration. In order to reflect the concentration more accurately, we optimized the extraction method of soil NO2‒ in this study. Moreover, soil ammonium (NH4+) and nitrate (NO3‒) were also systematically investigated to achieve efficient extraction of soil inorganic nitrogen. The results showed that un-buffered KCl significantly underestimated soil NO2‒ concentration compared to DIW. The highest recovery of NO2‒ was obtained by extracting with DIW at 10 min of oscillation for three soils. Compared with DIW, the concentration of NH4+ and NO3‒ in soil extracted from KCl solution increased significantly. Furthermore, the soil inorganic nitrogen content of extracts stored at 4°C for one day were closer to directly measurements of fresh samples than the other storage methods. Overall, the recommend analysis method for soil NO2‒ was extracted by DIW, oscillated for 10 min, and filtered by a 0.45 µm filter, and soil NH4+ and NO3‒ were extracted with KCl solution and oscillated for 30 min. The extract should be stored at 4°C and analyzed within 24 hours.

The process of Targeted Opinion Word Extraction (TOWE), a critical component of aspect-based sentiment analysis (ABSA), revolves around identifying opinionated words linked to specific aspect-terms within sentences. Existing deep learning approaches, while effective, often overlook the syntactic structure of sentences, a factor that previous studies have identified as beneficial for TOWE. In this study, we introduce the Syntactic-Enhanced Deep Learning Model (SEDLM) that integrates syntactic structures into deep learning frameworks for TOWE. Our approach leverages syntax-driven opinion potential scores and syntactic inter-word connections, enhancing model performance. Additionally, we introduce an innovative regularization strategy aimed at distinguishing word representations in TOWE tasks. Our comprehensive analysis reveals that SEDLM sets new benchmarks in performance across multiple standard datasets.

The UV/Vis absorption energies (νmax) of different solvatochromic probes measured in co-solvent/water mixtures are analysed as a function of the average molar concentration (Nav) of the solvent composition. Nav is discussed in terms of the underlying average molar mass (mol average or mass average) of the mixture. ET(30) of Reichardt`s dye B30 is the focus of the analysis. Methanol, ethanol, 1,2-ethanediol, 2-propanol, 2-methyl-2-propanol, 2-butoxyethanol, formamide, N-methylformamide (NMF), dimethylformamide (DMF), N-formylmorpholine (NFM), 1,4-dioxane and DMSO were used as co-solvents. Significant linear dependencies of ET(30) as a function of Nav can be demonstrated for formamide/water, 1,2-ethanediol/water, NMF/water and DMSO/water mixtures over the whole composition range. These mixtures belong to the group of solvents that do not enhance the water structure according to the Marcus classification. The specifics of the 1,4-dioxane/water mixtures are discussed. For alcohol/water mixtures with enhanced water structure, the influence of the solvent microstructure on ET(30) is particularly evident.

The inherent value and use of hydrocarbon from waste plastics and solvents can be extended through open-loop chemical recycling as this process converts plastic to range of non-plastic materials. This process is enhanced by first creating plastic-solvent-combinations from multiple sources which are then streamlined through single process stream. We report on the relevant mechanics for streamlining industrially relevant polymers such as polystyrene (PS), polypropylene (PP), high-density polyethylene (HDPE) and acrylonitrile butadiene styrene (ABS) into chemical slurries mixed with various organic solvents such as toluene, xylene and cyclohexane. The miscibility of the polymer feedstock within the solvent was evaluated using the Relative Energy Difference method, and the dissolution process was evaluated using the “Molecular theories in a continuum framework” model. These models were used to design a batch process yielding 1 tonne/h slurry by setting appropriate assumptions including constant viscosity of solvents, disentanglement-controlled dissolution mechanism and linear increase of the dissolved polymer’s mass fraction over time. Solvent selection was found to be the most critical parameter for the dissolution process. The characteristics of the ideal solvent are high affinity to the desired polymer and low viscosity. This work serves as a universal technical guideline for open-loop chemical recycling of plastics avoiding the growth of waste plastic in a circular economy framework.

The procedures for the extraction and separation of lipids and nutraceutics from microalgae using classic solvents have been used many times. However, these production methods usually require expensive and toxic solvents. Based on our studies involving the use of eco-sustainable methodologies and alternative solvents, we select ethanol (EtOH) and cyclopentyl methyl ether (CPME) for extracting bio-oil and lipids from algae. Different percentage of EtOH in CPME favors the production of an oil rich of SFA useful to production biofuel or rich of compounds bioactive. The proposed method for obtain a rich extract of saturated or unsaturated fatty acids from dry algal biomass is disclosed is eco-friendly and allows a good extraction yield. The method is compared both in extracted oil percentage yield and in extracted fatty acids selectivity to extraction by supercritical carbon dioxide.

This paper addresses the atmospheric emissions from oil and gas extraction and production in Greece. The study was carried out in 2014 in the Kavala gulf, which currently is the only location of oil and gas production in Greece and where the exploration activities for hydrocarbons started in the late ‘60’s. This study presents the qualitative and quantitative characteristics of atmospheric emissions, in relation also to the emissions’ control management system. Particular reference is made to sulphur compounds since the existence of volcanic rocks results to increased amounts of H₂S. The results shows that, currently, atmospheric emissions of pollutants during extraction and production of hydrocarbons in Greece are very low and do not have any significant effect on air quality and climate change. Since it is expected that exploitation of hydrocarbons and oil and gas extraction and production will increase in the future, appropriate measures should be taken to ensure environmental protection, such as the development of integrated monitoring systems and the use of up to date emission control technologies.

Chitin and its derivative, chitosan, have diverse applications in fields such as agriculture, medicine, and biosensors, amongst others. Extraction is primarily conducted from marine sources, such as crustaceans, which have been the focus of optimization process studies. However, there are other sources that are more readily available, such as insects, where insufficient research has been conducted. The house cricket (Acheta domesticus) is a promising source for chitin extraction because of its high chitin content, availability, and short lifespan. Modern chemical chitin extraction methods have not been standardized due to the use of different reagents, molar concentrations, temperatures, and reaction times across publications. Therefore, in this study, the compositional analysis of Acheta domesticus cricket flour was determined: 2.62% humidity, 4.3% ash content, 56.29% protein, 13.35% fat, 23.44% carbohydrates, and 15.71% crude fiber content. After a drying, defatting, demineralization, deproteinization, and bleaching process, chitin extraction was performed, and chitosan was obtained via a deacetylation reaction. The demineralization process was standardized at 30ºC for 3 hours using HCl 2M, resulting in 95.85 ± 0.012%. The deproteinization process was optimized at 80ºC for 45 minutes using NaOH 2.56 M, yielding 46.37 ± 3.86%. Finally, the identity and physicochemical characteristics of the compounds were determined through characterization with FTIR, XRD, SEM and DSC.

Like other organisms, fungi produce extracellular vesicles (EVs) that are involved in various biological processes, including intercellular communication and the transport of molecules between cells. These EVs can be applied in fungal pathogenesis, virulence, and interactions with other organisms, including host cells, in the case of fungal infections. While some types of mycoses are relatively common and easily treatable, certain neglected mycoses pose significant public health challenges, such as sporotrichosis, chromoblastomycosis, and paracoccidioidomycosis. These infectious diseases can cause significant morbidity and disability, leading to a reduced quality of life for the patients. So, research about the virulence factor is essential to understand how fungi escape the immune system. In this context, this manuscript reviews the study of fungi EVs, their cargo, their obtaining, and their role during the infectious process, which is extremely important for understanding this neglected mycosis.

Structured extraction of emergency event information can effectively enhance the ability to re-spond to emergency events. This article focuses on the extraction of Chinese document-level emergency events, which mainly faces two key issues in this field: first, related datasets; Secondly, existing DEE (document-level event extraction) studies mostly use sequence annotation to extract candidate entities in the subtask of candidate entity extraction without considering the problem of role overlapping between candidate entities. On the one hand, this article constructs a Chinese document-level emergency extraction dataset, CDEEE, which first annotates the issues of argu-ment scattering, multiple events, and role overlapping. On the other hand, this article proposes a model RODEE for the problem of role overlapping in DEE tasks. This model first uses two in-dependent modules to represent the head and tail positions of candidate entities, then uses a multiplication attention mechanism to interact with the two to obtain a scoring matrix. Finally, role-overlapping candidate entities are predicted to assist in completing DEE tasks. Experiments were conducted on our manually annotated dataset, CDEEE, and the results showed that RODEE can effectively solve the problem of role overlapping in candidate entities and improve the performance of the DEE model.

Cyrene was evaluated for the first time as a potential sustainable mobile phase solvent in re-versed-phase chromatography. As a benign biodegradable solvent, Cyrene is an attractive re-placement to classical non-green organic chromatographic solvents such as acetonitrile and a modifier, co-eluent to known green solvents such as ethanol. Compared to ethanol, Cyrene is less toxic, non-flammable, bio-based, biodegradable and cheaper solvent. A fire safety spider Chart was generated to compare the properties of Cyrene to ethanol and show its superiority as a greener solvent. Cyrene's behaviour, advantages, and drawbacks in reversed-phase chromatography, including cut-off value, elution power, selectivity, and effect on the column, were investigated using a model drug mixture of moxifloxacin and metronidazole. A monolithic C18 (10 x 4.6 mm) column was used as a stationary phase. Different ratios of Cyrene: ethanol with an aqueous portion of sodium acetate buffer mobile phases were tested. A mobile phase consisting of Cyrene: ethanol: 0.1 M sodium acetate buffer pH 4.25 (8:13:79, v/v) was selected as most suitable mobile phase system for separating and simultaneously determining metronidazole and moxifloxacin. The greenness and whiteness of the method were evaluated using the qualitative green assessment tool AGREE and the white analytical chemistry assessment tool RGB12. Further potentials of Cyrene as a solvent or modifier in normal phase chromatography, liquid chromatography-mass spectrometry, and supercritical fluid chromatography are discussed.

The combustion of fuel oil releases sulfur compounds, which react to form sulfur oxides that are harmful to the environment and pose a threat to human health. To mitigate these negative effects, it is crucial to pretreat fuel oil through desulfurization processes. One promising approach involves the use of deep eutectic solvents (DESs), carbon nanotubes (CNTs), and their composites (DESs/CNTs) to effectively reduce sulfur content in fuel oil.However, the conventional methods of DES-based extraction desulfurization and CNT-based adsorption desulfurization suffer from low desulfurization rates. Additionally, the composite material DESs/CNTs is in a semi-solidified form, resulting in high viscosity, complex operation procedures, and increased waste and environmental pollution. To address these challenges, this study focused on the preparation of CNTs/PEG-PVA hydrogel. This hydrogel not only maintains the high desulfurization rate observed in the DESs/CNTs composite material but also possesses several advantages. Firstly, it is convenient to use, offering ease of handling and application. Secondly, it is biodegradable, meaning it can break down naturally over time, reducing its impact on the environment. Lastly, the hydrogel is reusable, allowing for repeated use, thereby minimizing material waste. The desulfurization rate achieved with the CNTs/PEG-PVA hydrogel is remarkably high, reaching up to 99.8%. Moreover, the material utilization rate is close to 100%, meaning that almost all of the hydrogel is utilized in the desulfurization process, reducing unnecessary material consumption. In summary, the innovative CNTs/PEG-PVA hydrogel presents a highly efficient and environmentally friendly solution for desulfurization in fuel oil. Its superior desulfurization rate, alongside its convenience, biodegradability, and reusability, positions it as a promising alternative that not only ensures effective desulfurization but also contributes to sustainable practices in the energy industry.

Selective hydrogenation of nitrobenzene was carried out under solvent-free conditions using supported AuPd nanoparticles catalyst, prepared by modified impregnation method (MIm), as efficient catalyst. >99% yield of aniline (AN) was obtained after 15 hours at 90 °C, 3 bar H2 that can be used without any further purification or separation, therefore reducing cost and energy input. Supported AuPd nanoparticles catalyst, prepared by MIm, was found to be active and stable even after 4 recycle experiments whereas the same catalyst prepared by SIm deactivated during the recycle experiments. The most effective catalyst was tested for the chemoselective hydrogenation of 4-chloronitrobenzene (CNB) to 4-chloroaniline (CAN). The activation energy of CNB to CAN was found to be 25 kJ mol-1, while that of CNB to AN was found to be 31 kJ mol-1. Based on this, the yield of CAN was maximized (92%) by lowering the reaction temperature to 25 °C.

Acid promoted amination of 4-chloro-7H-pyrrolo[2,3-d]pyrimidine with anilines have been studied using hydrochloric acid. Four alcoholic solvents and water were evaluated as reaction medium, and the highest rate was observed in water. Although the initial rate increased by using higher concentration of acid, this leads to more solvolysis of the pyrrolopyrimidine, reducing the potential yield. The substrate scope of the amination of 4-chloro-7H-pyrrolo[2,3-d]pyrimidine in water using 0.1 equivalent of hydrochloric acid was evaluated using 20 aniline derivatives with variance in basicity and steric bulk. Preparative useful reactions were seen for 14 of the 20 derivatives. Unsuited anilines are ortho substituted anilines with a pKa below 1. Aliphatic and benzylic amines react poorly under these conditions, but such aminations can proceed well in water without acid. Pyrrolopyrimidines with a low water solubility, also reacted slowly in water, however they could easily be aminated in 2-propanol.

In this work, fluorinated graphene nanoscrolls (FGN) were synthesized via facile chemical methods under simple and mild conditions. Interestingly, the formation of the featured FGN was significantly solvent sensitive. Experimental results indicated that in the presence of aprotic solvent, for example, N,N dimethylformamide (DMF), the reaction system inclined to form the interesting FGN nanostructures. The structure and morphology of the prepared FGN were detailed characterized by atomic force microscopy (AFM), transmission electron microscopy (TEM), scanning electron microscopy (SEM) and X-ray diffraction (XRD) etc. The obtained FGN was used as a cathode material for primary lithium ion batteries with superior discharge specific capacity (eg. 979.3 mAhg-1), stable discharge platform and high energy density (eg. 2287.9 Wh kg-1), which fosters it a high density, low cost and durable candidate for cathode material for lithium ion batteries..

This comprehensive review paper provides a detailed analysis of the extraction methods employed in the dimension stone industry. Natural rock materials used in construction, have been historically extracted using primitive techniques such as thermal shock, hammer and chisel, and plug and feather. However, significant technological advancements have revolutionized the industry, leading to the widespread adoption of mechanized methods. One highly efficient technique is diamond wire cutting, which involves the utilization of diamond-engraved bits affixed to a tensioned steel wire. This method has demonstrated remarkable capabilities in minimizing waste generation and ensuring exceptional machining quality. Nonetheless, challenges such as high operating costs and wire breakage persist and require further investigation. In addition to diamond wire cutting, this review explores the utilization of circular diamond saws and frame sawing as alternative extraction methods. The geotechnical characteristics of the stone play a critical role in the selection of appropriate machinery, and researchers worldwide have conducted numerous studies to investigate the impact of each parameter on the extraction efficiency of these mechanized techniques. Moreover, controlled blasting with explosives emerges as a promising alternative for dimension stone extraction, warranting further exploration and optimization.

Scintillators play a key role in the detection chain of several applications which rely on the use of ionizing radiation, and it is often mandatory to extract and detect the generated scintillation light as efficiently as possible. In positron emission tomography (PET), for example, both energy resolution and coincidence resolving time, two of the key detection parameters, depend strongly on the total amount of light which reaches the photodetector surface as well as its spatial and temporal distribution. Typical inorganic scintillators do however feature a high index of refraction, which impacts light extraction efficiency in a negative way. Furthermore, several applications such as preclinical PET rely on pixelated scintillators with small pitch. In this case, applying reflectors on the crystal pixel surface, as done conventionally, can have a dramatic impact of the packing fraction and thus the overall system sensitivity. This paper presents a study on light extraction techniques, as well as combinations thereof, for two of the most used inorganic scintillators (LYSO and BGO). Novel approaches, employing distributed Bragg reflectors (DBRs), metal coatings, and a modified Photonic Crystal (PhC) structure, are described in detail and compared with commonly used techniques. The nanostructure of the PhC is surrounded by a hybrid organic/inorganic silica sol-gel buffer layer which ensures robustness while maintaining its performance unchanged. We observed in particular a maximum light gain of about 41% on light extraction and 21% on energy resolution for BGO, a scintillator which has gained interest in the recent past due to its prompt Cherenkov component and lower cost.

The latest methods based on deep learning have achieved amazing results regarding the complex work of inpainting large missing areas in an image. This type of method generally attempts to generate one single "optimal" inpainting result, ignoring many other plausible results. However, considering the uncertainty of the inpainting task, one sole result can hardly be regarded as a desired regeneration of the missing area. In view of this weakness, which is related to the design of the previous algorithms, we propose a novel deep generative model equipped with a brand new style extractor which can extract the style noise (a latent vector) from the ground truth image. Once obtained, the extracted style noise and the ground truth image are both input into the generator. We also craft a consistency loss that guides the generated image to approximate the ground truth. Meanwhile, the same extractor captures the style noise from the generated image, which is forced to approach the input noise according to the consistency loss. After iterations, our generator is able to learn the styles corresponding to multiple sets of noise. The proposed model can generate a (sufficiently large) number of inpainting results consistent with the context semantics of the image. Moreover, we check the effectiveness of our model on three databases, i.e., CelebA, Agricultural Disease, and MauFlex. Compared to state-of-the-art inpainting methods, this model is able to offer desirable inpainting results with both a better quality and higher diversity. The code and model will be made available on https://github.com/vivitsai/SEGAN.

This study delves into the extraction and compositional analysis of soybean meal protein isolates (SMPI) compared to soy protein isolates (SPI), focusing on their functional and structural properties, digestibility, amino acid composition, and the impact of various proteases on antinutritional factors. By leveraging alkaline (0.25 % of NH4OH) extraction and isoelectric precipitation, SMPI was efficiently obtained. Compositional characteristics revealed that SMPI has high moisture, protein, and ash, but lower fat, and carbohydrate content compared to SPI. Alcalase, Neutrase and Pepsin hydrolysis indicated lower digestibility of SMPI than SPI. Fourier-transform infrared spectroscopy and sodium dodecyl sulfate-polyacrylamide gel electrophoresis provided similar molecular structure and protein molecular weight distribution. This comprehensive analysis underscores the valorization of soybean meal, promoting its use beyond conventional animal feed towards nutritional supplements and bio-based products, thereby contributing to environmental sustainability and the enhancement of global food systems.

A topic of growing interest in urban remote sensing is the automated extraction of geometrical building information for 3D city modeling. Roof geometry information is useful for applications such as urban planning, solar potential estimation and telecommunication installation planning, and wind flow simulations for pollutant diffusion analysis. Recent research has proven that the advance in remote sensing technologies and deep learning methods offer the prospects of deriving the roof structure information accurately and efficiently. In this study, we propose a Vectorized Roof Extractor- method based on Fully Convolutional Networks (FCNs) and advanced polygonization method to extract roof structure from aerial imagery and a normalized Digital Surface Models (nDSM) in a regularized vector format. The roof structure consists of building outlines, external edges of the building roof, inner rooflines, internal intersections of the main roof planes. The methodology is comprised of segmentation, vectorization and post-processing for outer rooflines, external edges of the building roof, and inner rooflines, and internal intersections of the main roof planes. For the comparison, we adapt the Frame field Learning (FFL) method originally designed to extract building polygons [1]. Our experiments are conducted on a custom data set derived for the city of Enschede, The Netherlands, using aerial imagery, nDSM and manually digitized training polygons. The results show that the proposed Vectorized Roof Extractor outperformed adapted FFL on PoLiS distance with values of 3.5 m and 1.2 m for outlines and inner rooflines, respectively. Furthermore, the model surpassed the adapted FFL on PoLiS-thresholded F-score for outlines and inner rooflines, with 0.31 and 0.57, respectively. The Vectorized Roof Extractor produced adequate visual results, with straighter walls and fewer missed inner roofline detections. It can predict buildings with common walls thanks to skeleton graph computation. To summarize, the proposed method is suitable for urban applications and has the potential to be improved further.

Acanthopanax senticosus(rupr. rt. Maxim.; AS) is a medicinal plant used in the clinical treatment of cerebrovascular diseases and central nervous system disorders, significantly improving blood lipid levels and endothelial cell function in patients with acute cerebral infarction. Isofraxidin, one of the active ingredients of AS, is the core of the medical effects, and its extraction and purification depend on organic solvents. Deep eutectic solvents (DESs) is a new green solvent, synthesized by intermolecular hydrogen bonding between hydrogen bond donors (HBD) and hydrogen bond acceptors (HBA), which has non-toxic, high separation and purification efficiency, and environmentally friendly compared with traditional organic solvents. In this paper, DES was used for the extraction of isofraxidin from AS. The primary findings demonstrate that the DESs had a viscosity higher than that of ethanol, and even adding a tiny amount of water (about 10%) would trigger solvent redistribution, leading to a considerable reduction in solvent viscosity. In comparison to ethanol, the extraction rate of isofraxidin by DESs was 2-3 times higher. Thus, this work developed a new technique for using green extraction of isofraxidin that has some practical implications.

Repair mortar is commonly used to rehabilitate reinforced concrete structures or components that exhibit a relatively high level of distresses. Yet, this repair mortar can be contaminated by salt from its service environment. This work employs a two-dimensional finite element model to investigate the transport behavior of ionic species in salt-contaminated and water-saturated repair mortar under an externally applied electric field. The model was experimentally validated and then utilized to evaluate the effectiveness of electrochemical chloride extraction (ECE) with or without electrical injection of corrosion inhibitor (EICI). In the case study, both the ECE alone and the ECE+EICI treatment was found effective in decontaminating the zone in front of the steel rebar. In both techniques, the magnitude of current density has a significant effect on removing chloride out of the mortar and increasing the pH of the pore solution near the rebar, whereas the treatment time any not have a significant effect under some scenarios. The injection of the organic corrosion inhibitor significantly slowed down the removal of chloride. Changes in the ionic distribution in the mortar were generally beneficial in reducing the corrosion risk of the steel rebar and thus extending the service life of the repair mortar.

Two solvated rhenium(IV) complexes with formula [ReCl4(bpym)]·MeCN (1) and [ReCl4(bpym)]·CH3COOH·H2O (2) [bpym = 2,2'-bipyrimidine] have been prepared and characterized by means of Fourier transform infrared spectroscopy (FT–IR), scanning electron microscopy and energy dispersive X-ray analysis (SEM–EDX), single-crystal X-ray diffraction (XRD) and SQUID magnetometer. 1 and 2 crystallize in the monoclinic system with space groups P21/n and P21/c, respectively. In both compounds, the Re(IV) ion is six-coordinate and bound to four chloride ions and two nitrogen atoms of a 2,2’-bipyrimidine molecule forming a distorted octahedral geometry around the metal ion. In the crystal packing of 1 and 2, intermolecular halogen⋯halogen and π⋯halogen type interactions are present. Hydrogen bonds take place only in the crystal structure of 2. Both compounds exhibit an akin crystal framework based on halogen bonds. Variable-temperature dc magnetic susceptibility measurements performed on microcrystalline samples of 1 and 2 show a similar magnetic behavior for both compounds, with antiferromagnetic exchange between the Re(IV) ions connected mainly through intermolecular Re-Cl···Cl-Re interactions.

The four solvent extractives obtained from aerial parts of Leucophyllum frutescens were evaluated for their Total Antioxidant Activity (TAA) by ammonium molybdate method, scavenging potential by 2,2-diphenyl-1-picrylhydrazyl (DPPH) and Trolox-Equivalent Antioxidant Capacity (TEAC) assays, metal-reducing potential by Cupric Reducing Antioxidant Capacity (CUPRAC) and Ferric Reducing Antioxidant Power (FRAP) assays, Total Phenolic Content (TPC), Total Flavonoid Content (TFC) and their biological activities. The study concluded that BULE exhibited total antioxidant activity (226.235±1.222 mg AA.Eq.gm-1 DE±S.D) by molybdate method, CHLE exhibited more scavenging potential (DPPH 209.589±8.500 mg trolox Eq.gm-1 DE±S.D and TEAC 210.166±7.954 mg trolox Eq.gm-1 DE±S.D) and reducing potential (CUPRAC 646.889±16.889 mg trolox Eq.gm-1 DE±S.D & FRAP 472.981±15.625 mg trolox Eq.gm-1 DE±S.D). Phytochemical quantification concluded high TPC by BULE (189.369±1.393 mg GA.Eq.gm-1 DE±S.D) and high TFC by CHLE (232.458±1.589 mg Qu.Eq.gm-1 DE±S.D). Strong inhibition of α-glucosidase and urease enzymes was observed by HELE (IC50 0.3321±0.007 mg.ml-1±SD) and BULE (IC50 4.09±0.357 mg.ml-1±SD) extractives, respectively. The hemolytic effect shown by hexane extract (HELE) was higher with HA50 25.545±0.927 ug.ml-1±SD whereas methanol (MELE), chloroform (CHLE), and butanol (BULE) exhibited hemolytic effects at higher concentration with HA50 400.067±1.364, 321.394±1.332, and 332.957±0.465 µg.ml-1±SD, respectively. GC-MS profiling of HELE of L. frutescens was performed for qualitative analysis. The principal phytochemicals tentatively identified by GC-MS analysis of HELE accounts for fatty acids (60.221%), lignans (17.687%), ketones (3.358%), phenols (2.584%), sesquiterpenes (1.265%), and aldehydes (0.345%).

The groundbreaking Advanced Forest-Based Tagging Framework (AFTF) represents a paradigm shift in the domain of information extraction from medical texts. AFTF introduces a novel dual-binary tree structure that redefines how entity-relation triples are extracted. This innovative approach directly tackles the limitations of traditional linear and graph-based methods, effectively addressing challenges related to overlapping triples and computational efficiency. The AFTF model stands as a beacon of excellence, surpassing established baselines by significant margins in comprehensive evaluations on two pivotal medical datasets. Notably, AFTF achieves remarkable improvements in F1 scores, showcasing its prowess in accurate information extraction from complex medical narratives. Beyond its exceptional performance in the medical domain, AFTF exhibits remarkable versatility. This adaptability is vividly demonstrated through its robust performance across three diverse public datasets, further affirming its position as a versatile and reliable solution for information extraction tasks. This paper provides a comprehensive exposition of the AFTF architecture, shedding light on its innovative design principles and its efficient handling of intricate medical texts. AFTF represents a groundbreaking step forward in the realm of information extraction, promising enhanced accuracy, efficiency, and adaptability for a wide range of applications.

Fish oil rich in polyunsaturated omega-3 fatty acids is extracted in high yield from anchovy filleting waste using d-limonene as green biosolvent in a simple solid-liquid extraction performed by mechanically stirring and maceration followed by limonene removal via evaporation under reduced pressure. As limonene is renewably obtained from waste orange peel, this protocol establishes a circular bioeconomy method to obtain valued omega-3 extracts from biowaste available worldwide in several million t/year amount. The method closes the materials cycle and opens the route to full valorisation of an important biological resource so far mostly discarded as waste. Significant economic opportunities benefiting local communities, the ecosystem and public health are anticipated.

Antioxidants are molecules that neutralize free radicals. In general, the reaction mechanisms of antioxidants are well known. The main reaction mechanisms of antioxidants are electron transfer (ET), proton transfer (PT), H atom transfer (HAT) and radical adduction (RAF). The study of these mechanisms is helpful to understand how antioxidants control high free radical levels on the cell. There are many studies focused on determine the main mechanism of an antioxidant to neutralize a wide spectrum of radicals, mainly reactive oxygen species (ROS) type radicals. Most of these antioxidants are polyphenols type compounds. Some esters, amides and metal-antioxidants have shown antioxidant activity. There are few experimental and theoretical studies about the antioxidant reaction mechanism of the aforementioned compounds. In this work, we shown the reaction mechanism proposed of an amide and its metal-antioxidant counterpart. We show how the presence of the metal increase the electron transfer on polar media and the H transfer in non-polar media. Even though, esters and amides are non-polar compound, the scavenger activity is good for the metal-antioxidant compound in no-polar media

The synthesis of nitrogen-based heterocycles has always been considered essential in the development of pharmaceuticals in medicine and agriculture. This explains why various synthetic approaches have been proposed in recent decades. However, performing as methods often imply harsh conditions or the employment of toxic solvents and dangerous reagents. Mechanochemistry is undoubtedly one of the most promising technologies currently used for reducing any possible environmental impact due to the worldwide interest in developing solvent-free synthetic pathways. Following this line, we propose a renewed mechanochemical protocol for synthesizing various heterocyclic classes by exploiting the reducing proprieties and the electrophilic nature of thiourea dioxide (TDO). Simultaneously using the ready availability and low cost of a component of the textile industry such as TDO and all the advantages brought by a green technique such as mechanochemistry, we plotted the route towards a more sustainable and eco-friendly methodology for obtaining heterocyclic moieties.

Solvent-free, single-ion conducting electrolytes are sought after for use in electrochemical energy storage devices. Here, we investigate the ionic conductivity and how this property is influenced by segmental mobility and conducting ion number in crosslinked single-ion conducting polyether-based electrolytes with varying tethered anion and counter-cation types. Crosslinked electrolytes are prepared by the polymerization of poly(ethylene glycol) diacrylate (PEGDA), poly(ethylene glycol) methyl ether acrylate, and ionic monomers. The ionic conductivity of the electrolytes is measured and interpreted in the context of differential scanning calorimetry and Raman spectroscopy measurements. A lithiated crosslinked electrolyte prepared with PEG₃₁DA and STFSI monomers is found to have a lithium ion conductivity of 3.2 × 10^-6 and 1.8 × 10⁻⁵ S/cm at 55 and 100 °C, respectively. The percentage of unpaired anions for this electrolyte was estimated at about 23% via Raman spectroscopy. Despite the large variances in metal cation – STFSI binding energies as predicted via DFT and large variations in ionic conductivity, STFSI-based crosslinked electrolytes with the same charge density and varying cations (Li, Na, K, Mg, and Ca) were estimated to all have unpaired anion populations in the range of 19 to 29%.

Due to the advantages of low latency, low power consumption and high flexibility of FPGA-based acceleration technology, it has been more and more widely studied and applied in the field of computer vision in recent years. An FPGA-based feature extraction and tracking accelerator for real-time visual odometry (VO) and visual simultaneous localization and mapping (V-SLAM) is proposed, which can realize the complete acceleration processing capability of the image front-end and directly output the feature point ID and coordinates to the backend. The accelerator consists of image preprocessing, pyramid processing, optical flow processing, and feature extraction and tracking modules. For the first time, it implements a hardware solution that combines features from accelerated segment test (FAST) corners with Gunnar Farneback (GF) dense optical flow, to achieve better feature tracking performance and provide more flexible technical route selection. In order to solve the scale invariance and rotation invariance lacking problem of FAST features, an efficient pyramid module with a five-layer thumbnail structure is designed and implemented. The accelerator is implemented on a modern Xilinx Zynq FPGA. The evaluation result shows that the accelerator can achieve stable tracking of features of violently shaking images, and is consistent with the results of MATLAB code running on PC. When operating at 100MHz, the accelerator can process 108 frames per second for 720P images and 48 frames per second for 1080P images. Compared to PC CPUs that consume seconds of time, the processing latency is greatly reduced to the order of milliseconds, making GF dense optical flow an efficient and practical technical solution on the edge side.

Citrus peels are considered as a rich source of valuable biomolecules like pectin as polymer of polysaccharide acid. In this study, response surface methodology was used to optimize pectin extraction from Citrus clementina peels using citric acid as extraction solvent. The effect of parameters conditioning the extraction process and pectin yield (pH, temperature, extraction time, solid/liquid ratio, and raw material particle size) was investigated using a Box-Behnken design. The quality of the extracted pectin was assessed both chemically (moisture, ash, protein, and sugar content) and functionally (gelling power and emulsifying activity). According to the screening experiment, the factors pH, temperature, and particle size were the main factors influencing the pectin yield. The adjusted mathematical model enabled us to plot response surfaces in order to determine optimal extraction conditions. The highest production yield of pectin (26.6%) was obtained at the optimal conditions of: pH = 1.5; temperature 100 °C and particle size = 0.1 mm for an extraction time of 30min. Compared to the predicted value of 26.6%, the experimental extraction yield was about 21.4% of pectin. Concerning the functional properties, the extracted pectin has a high gelling power of 164°SAG and an emulsifying activity of 38.5%.

Best practices in global health training prioritize leadership and engagement from investigators from low- and middle-income countries (LMICs), along with more conscientious community consultation and research that benefits local participants and autochthonous communities. However, well into the 20th century, international research and clinical care were rife with paternalism, extractive practices, and racist ideation, with race presumed to explain both vulnerability or protection from various diseases despite scientific evidence for more precise mechanisms for infectious disease. We highlight experiences in global research on health and illness among indigenous populations in LMICs, seeking to clarify what is both scientifically essential and ethically desirable in research with human subjects; we apply a critical view towards race and racism as historically distorting elements that must be acknowledged and overcome.

This paper proposes an approach for image data extraction and driving behavior analysis using geographic information and driving data. Information derived from geographic and global positioning systems was used for image data extraction. In addition, we used an onboard diagnostic II and a controller area network bus logger to record driving data for driving behavior analysis. Driving behavior was analyzed using sparse automatic encoders and data exploration to detect abnormal and aggressive behavior. A regression analysis was used to derive the relationship between aggressive driving behavior and road facilities. Several traffic improvements were proposed for specific intersections and roads. The results indicate that lane ratios without lane markings and with straight lane markings are important features that affect aggressive driving behaviors.

Deep eutectic solvents (DESs) have emerged as novel alternatives to common solvents and VOCs. Their employment as electrolytes in battery has been an area of intense research. In this context, understanding changes in physicochemical properties of DESs in the presence of Li salts becomes of utmost importance. Solvatochromic probes have potential to gauze such changes. It is reported herein that one such uv-vis molecular absorbance probe, Reichardt’s betaine dye 33, effectively manifests changes taking place in a DES Glyceline, composed of H-bond accepting salt choline chloride and H-bond donor glycerol in 1 : 2 molar ratio, as salt LiCl is added. Lowest energy intramolecular charge-transfer absorbance band of this dye exhibits 17 nm hypsochromic shift as up to 3.0 molal LiCl is added to Glyceline. The estimated ETN parameter shows linear increase with LiCl mole fraction. Spectroscopic responses of betaine dye 33, N,N-diethyl-4-nitroaniline and 4-nitroaniline are used to assess empirical Kamlet-Taft parameters of dipolarity/polarizability (π*), H-bond donating acidity (α) and H-bond accepting basicity (β) as a function of LiCl concentration in Glyceline. LiCl addition to Glyceline results in increase in α and no change in π*and β. It is proposed that added lithium interacts with oxygen of the –OH functionalities on the glycerol rendering the solvent with increased H-bond donating acidity. It is observed that pyrene, a popular fluorescence probe of solvent polarity, does respond to the addition of LiCl to Glyceline, however, the change in pyrene response starts to become noticeable only at higher LiCl concentration (mLiCl ≥ 1.5 m). Reichardt’s betaine dye is found to be highly sensitive and versatile in gauzing physicochemical properties of DESs in the presence of LiCl.

Soil microbiome plays key role in plant health. Native soil microbiome inoculation, metagenomic profiling and high-throughput cultivation require efficient microbe extraction. The sonication and oscillation are most common methods to extract soil microbiome. However, the extraction efficiency of those methods has barely been investigated. Here, we compared the culturable microbe numbers, community structures and alpha diversities among the methods including sonication, oscillation, centrifugation and their processing time. The results showed that, sonication significantly increases culturable colony number compare with oscillation and centrifugation factors. Furthermore, sonication strategy shows a main factor influence extraction efficiency, but increased sonication time can recovery this impact. Finally, processing times of extraction show a significant negative relationship with α diversity among extracted microbiota. In conclusion, sonication is a main factor for enrich in-suit microbiota, and increased extraction time significantly decrease α diversity of extracted microbiota. These results can provide insights into the isolation and utilization of microorganism source.

Contemporary advanced models for aspect-targeted opinion word extraction (ATOWE), which predominantly utilize BERT-based encoders at a word level, have shown limited advancements when integrated with graph convolutional networks (GCNs) for syntactic tree assimilation. Recognizing the prowess of BERT subwords in encapsulating rare or context-poor words, this study pivots from syntactic trees to BERT subwords, omitting GCNs from the structural framework. Our approach, named Aspect-Enhanced Wordpiece Extraction Model (AEWEM), focuses on refining aspect representation during encoding. We propose an input format of paired sentence-aspect, diverging from traditional single-sentence inputs. AEWEM demonstrates superior performance on benchmark datasets, establishing a robust foundation for future explorations in this domain.

Extracting railway tracks is crucial for creating electronic railway maps. Traditional methods require significant manual labor and resources, while existing neural networks have limitations in efficiency and precision. To address these challenges, a railway track extraction method using an improved DeepLabV3+ model is proposed, which incorporates several key enhancements. Firstly, the encoder part of the method utilizes the lightweight network MobileNetV3 as the backbone extraction network for DeepLabV3+. Secondly, the decoder part adopts the lightweight universal upsampling operator CARAFE for upsampling. Lastly, to address any potential extraction errors, morphological algorithms are applied to optimize the extraction results. Additionally, a dedicated railway track segmentation dataset is created to train and evaluate the proposed method. The experimental results demonstrate that the model achieves impressive performance on the railway track segmentation dataset and DeepGlobe dataset. The MIoU scores are 88.93% and 84.72%, with Recall values of 89.02% and 86.96%. Moreover, the overall accuracy stands at 97.69% and 94.84%. The algorithm's operation time is about 5% lower in comparison to the original network. Furthermore, the morphological algorithm effectively eliminates errors like holes and spots. These findings indicate the model's accuracy, efficiency, and the enhancement brought by the morphological algorithm in error elimination.

The objective to fast-track the mapping and registration of large numbers of unrecorded land rights globally, leads to the experimental application of Artificial Intelligence (AI) in the domain of land administration, and specifically the application of automated visual cognition techniques for cadastral mapping tasks. In this research, we applied and compared the ability of rule-based systems within Object Based Image Analysis (OBIA), as opposed to human analysis, to extract visible cadastral boundaries from Very high resolution (VHR) World View-2 image, in both rural and urban settings. From our experiments, machine-based techniques were able to automatically delineate a good proportion of rural parcels with explicit polygons where the correctness of the automatically extracted boundaries was 47.4% against 74.24% for humans and the completeness of 45% for machine, as against 70.4% for humans. On the contrary, in the urban area, automatic results were counterintuitive: even though urban plots and buildings are clearly marked with visible features such as fences, roads and tacitly perceptible to eyes, automation resulted in geometrically and topologically poorly structured data, that could neither be geometrically compared with human digitised, nor actual cadastral data from the field. These results provide an updated snapshot with regards to the performance of contemporary machine-drive feature extraction techniques compared to conventional manual digitising.

Onion is not just an edible food but its seeds can also be an important source of valuable oil with various sensitive applications mainly in pharmaceutical, cosmetic and food fields. This has encouraged the use of a supercritical fluid extraction in the present study to obtain oil from local onion seeds, hence avoiding even traces of organic solvents. For several advantages carbon dioxide at supercritical conditions was used as the fluid. The effects of four key operating parameters like pressure, temperature, particle size and CO2 mass flowrate were investigated in ranges of [150, 250 bars], [35, 65°C], [0.25, 0.85mm] and [50, 100g/min], respectively, using a Box-Behnken experimental design, for a constant extraction time of 3 hours. This led to optimal operating conditions of 250 bar, 57°C, 0.25mm and 50g CO2/min for the highest oil extraction yield value of 24.36%. Furthermore, gas chromatography-mass spectrometry (GC-MS) was used to identify qualitatively and quantitatively the chemical composition of the onion seed oils. About ten components were identified in the extracts, but with four major ones, namely 9,12-Octadecadienoic acid ,methyl ester, 9,12-Octadecadienoic acid (Z,Z)-,methyl ester, 9-Octadecadienoic acid (Z)-,methyl ester and Hexadecanoic acid, methyl ester, present with significant percentages, depending on the operating parameters values. These fatty acids are well known for their benefits for human health. Finally the study shows the importance and the merits of fluids when used under particular conditions of pressure and temperature, in very sensitive industrial fields.

Radiomics involves the extraction of information from medical images not visible to the human eye. There is evidence these features can be used for treatment stratification and outcome prediction. However, there is much discussion about the reproducibility of results between different studies. This paper studies the reproducibility of CT texture features used in radiomics, comparing two feature extraction implementations namely Matlab toolkit and Pyradiomics when applied on independent datasets of CT scans of patients i) the open access RIDER dataset containing a set of repeat CT scans taken 15 minutes apart for 31 patients (RIDER Scan 1 and Scan 2 respectively) treated for lung cancer and ii) the open access HN1 dataset containing 137 patients treated for head and neck cancer. Gross tumor volume (GTV) manually outlined by an experienced observer available on both datasets was used. 43 common radiomics features available on Matlab and Pyradiomics were calculated using 2 intensity-level quantization methods with and without an intensity threshold. Cases were ranked for each feature for all combinations of quantization parameters and the Spearman’s rank coefficient, rs, calculated. Reproducibility was defined when a highly correlated feature in the RIDER dataset also correlated highly in the HN1 dataset and vice versa. 29 out of 43 reported stable features were found to be highly reproducible between Matlab and Pyradiomics implementations, having consistently high correlation in rank ordering for RIDER Scan 1 and RIDER Scan 2 (rs &gt; 0.8). 18/43 reported features were common in RIDER and HN1 datasets, suggesting they may be agnostic to disease site. Useful radiomics features should be selected based on reproducibility. This study identified a set of features that meet this requirement and validated the methodology for evaluating reproducibility between datasets.

Archaeological topography identification from high-resolution DEMs is a current method that is used with high success in archaeological prospecting of wide areas. I present a methodology trough which burial mounds (tumuli) from LiDAR DEMS can be identified. This methodology uses geomorphometric and statistical methods to identify with high accuracy burial mound candidates. Peaks, defined as local elevation maxima are found as a first step. In the second step, local convexity watershed segments and their seeds are compared with positions of local peaks and the peaks that correspond or have in vicinity local convexity segments seeds are selected. The local convexity segments that correspond to these selected peaks are further feed to a Random Forest algorithm together with shape descriptors and descriptive statistics of geomorphometric variables in order to build a model for the classification. Multiple approaches to tune and selected the proper training dataset, settings and variables were tested. The validation of the model was performed on the full dataset where the training was performed and on an external dataset in order to test the usability of the method for other areas in a similar geomorphological and archaeological setting. The validation was performed against manually mapped and field checked burial mounds from two neighbor study areas of 100 km² each. The results show that by training the Random Forest on a dataset composed of between 75% to 100% of the segments corresponding to burial mounds and ten times more non-burial mounds segments selected using latin hypercube sampling, 93% of the burial mound segments from the external dataset are identified. There are 42 false positive cases that need to be checked, and there are two burial mound segments missed. The method shows great promise to be used for burial mound detection on wider areas by delineating a certain number of tumuli mounds for model training.