The impulse of the Fourth Industrial Revolution is triggering the demand for few specific metals. These include copper, silver, gold, and platinum group metals (PGMs), with important applications in renewable energies, green hydrogen, and electronic products. However, the continuous extraction of these metals is leading to a rapid decline in their ore grades and, consequently, increasing the environmental impact of extraction. Hence, obtaining metals from secondary sources, such as waste electrical and electronic equipment (WEEE), becomes imperative for both environmental sustainability and ensuring availability. This recovery entails few problems such as allocation due to the simultaneous production of several metals, the use of non-renewable resources, and the exergy destruction during the life cycle of the metals. Therefore, this work analyses the waste printed circuit boards (PCBs) recycling process by proposing different exergy-based cost allocations for the mentioned metals, disaggregating the exergy cost into non-renewable and renewable, and considering the complete life cycle of metals with the Circular Thermoeconomics methodology. The results show a significant saving of non-renewable energy by using renewable energies in primary extraction (67-87%), recycling (97.6-98.5%), and renewable energies in recycling (98.7%, 99.0%), compared to conventional primary extraction. However, when considering the entire life cycle, between 47% and 53% of the non-renewable exergy is destroyed during recycling. Therefore, delaying recycling as much as possible would be the most desirable option for maximizing the use of non-renewable resources, which nature cannot replace in a short time.

Abstract: As a low-input crop, Miscanthus offers numerous advantages that, in addition to agricultural applications, permits its exploitation for energy, fuel, and material production. Depending on the Miscanthus genotype, season, and harvest time as well as plant component (leaf versus stem), correlations between structure and properties of the corresponding isolated lignins differ. Here, a comparative study is presented between lignins isolated from M. x giganteus, M. sinensis, M. robustus and M. nagara using a catalyst-free organosolv pulping process. The lignins from different plant constituents are also compared regarding their similarities and differences regarding monolignol ratio and important linkages. Results showed that the plant genotype has the weakest influence on monolignol content and interunit linkages. In contrast, structural differences are more significant among lignins of different harvest time and/or season. Analyses were performed using fast and simple methods such as nuclear magnetic resonance (NMR) spectroscopy. Data was assigned to four different linkages (A: b-O-4 linkage, B: phenylcoumaran, C: resinol, D: b-unsaturated ester). In conclusion, A content is particularly high in leaf-derived lignins at just under 70 % and significantly lower in stem and mixture lignins at around 60 % and almost 65 %. The second most common linkage pattern is D in all isolated lignins, the proportion of which is also strongly dependent on the crop portion. Both stem and mixture lignins, have a relatively high share of approximately 20 % or more (maximum is M. sinensis Sin2 with over 30 %). In the leaf-derived lignins, the proportions are significantly lower on average. Stem samples should be chosen if the highest possible lignin content is desired, specifically from the M. x giganteus genotype, which revealed lignin contents up to 27 %. Due to the better frost resistance and higher stem stability, M. nagara offers some advantages compared to M. x giganteus. Miscanthus crops are shown to be very attractive lignocellulose feedstock (LCF) for second generation biorefineries and lignin generation in Europe.

Companies are increasingly focusing on sustainable business practices. Internal and external stakeholders’ expectations manifest in legal requirements, national and international standards, and market and customer expectations, among other things, must be considered. In addition to profit maximization as the usual target for corporate management, management must consider environmental sustainability aspects such as resource efficiency, greenhouse gas intensity, and a company's emissions behavior. In addition, social aspects relating to the company's employees, the immediate urban environment, the situation in the supply chain, and effects on the market environment must increasingly be considered. Specifically, companies are faced with the chal-lenge of dealing with conflicting objectives regarding the various aspects of sustainability and, if necessary, weighing them up against each other. These trade-offs must be made against the company's socio-economic and ecological environment, corporate strategy, and sustainability goals. This paper provides an overview of current approaches and research gaps on this topic through a literature review. It shows a lack of methods and frameworks to specifically deal with trade-offs and conflicts of goals.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

Deploying Cellular Internet of Things (CIoT) devices in urban and remote areas faces significant energy efficiency challenges. This is especially true for Narrowband IoT (NB-IoT) devices, which are expected to function on a single charge for up to 10 years while transmitting small amounts of data daily. The 3rd Generation Partnership Project (3GPP) has introduced energy-saving mechanisms in Releases 13 to 16, including Early Data Transmission (EDT) and Preconfigured Uplink Resources (PUR). These mechanisms extend battery life and reduce latency by enabling data transmission without an active Radio Resource Control (RRC) connection or Random Access Procedure (RAP). This paper examines these mechanisms using the LENA-NB simulator in the ns-3 environment, which is a comprehensive framework for studying various aspects of NB-IoT. The LENA-NB has been extended with PUR, and our analysis shows that PUR significantly enhances battery life and latency efficiency, particularly in high-density environments. Compared to the default RAP method, PUR reduces energy consumption by more than 2.5 times and increases battery life by 1.6 times. Additionally, PUR achieves latency reductions of 2.5-3.5 times. The improvements with PUR are most notable for packets up to 125 bytes. Our findings highlight PUR’s potential to enable more efficient and effective CIoT deployments across various scenarios. This study represents a detailed analysis of latency and energy consumption in a simulated environment, advancing the understanding of PUR’s benefits.

The properties of coatings obtained using two surface preparation methods were compared: heating and etching by ion bombardment with plasma generation by arc evaporators and heating and etching by a glow discharge. A Ti-TiN-(Ti,Cr,Al)N coating was deposited. The use of a glow discharge provides better resistance of the coating to destruction during the scratch test and wear resistance of metal-cutting tools when turning steel. As the cutting speed increases, the advantage in wear resistance of the coating deposited using a glow discharge increases. During the process of heating and etching by ion bombardment with metal ions, a nanolayer rich in cobalt and tooling elements (iron, molybdenum) is formed in the area of the interface of the coating and the carbide substrate. When heated and etched by a glow discharge, such a layer does not form. When using both methods, there is identical diffusion of tungsten into the coating and diffusion of chromium and possibly titanium into the substrate. Thus, the glow discharge heating and etching method can be effectively used in the process of PVD coating deposition.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

The scientific community has shown considerable interest in Industry 4.0 due to its capacity to revolutionise the manufacturing sector through digitalisation and data-driven decision-making. However, the actual implementation of Industry 4.0 within complex industrial settings presents obstacles that are typically beyond the scope of mainstream research articles. In this paper, a comprehensive case-study detailing our collaborative partnership with a leading medical device manufacturer is presented. The study traces their evolution from a state of limited digitalisation to the development of a digital intelligence platform that leverages data and machine learning models to enhance operations across a wide range of critical machines and assets. The main business objective was to enhance the energy efficiency of the manufacturing process, thereby improving its sustainability measures while also saving costs. The project encompasses energy modelling and analytics, Fault Detection and Diagnostics (FDD), renewable energy integration and advanced visualisation tools. Together, these components enable informed decision making in the context of energy efficiency.

This study aims to analyse the technical viability and economic feasibility of rainwater harvesting systems for single and multifamily residential buildings in the city of Florianópolis, Brazil. Simulations were conducted for representative buildings in the city under different water usage scenarios and system designs, in a total of 36 simulation scenarios. An economic analysis was performed for four scenarios over a twenty-year period. Both initial and operational costs were considered and net present value, internal rate of return and payback used as feasibility indicators. Almost all of the cases simulated were technically viable for the group of houses, and up to 78.9% for flats. As for the economic analysis, for houses, between 60.1% and 74.8% of the cases were economically feasible, achieving a discounted payback period ranging from 6.2 to 8.6 years. For flats, between 57.8% and 64.2% of the cases were economically feasible, achieving a discounted payback period ranging from 4.8 to 5.6 years. As the water tariff in the city underwent changes recently, the former and current tariff formats were compared. The current tariff format provides more economic benefits for saving potable water, and leads to a higher net present value and a shorter discounted payback period.

The growing interest in benchtop NMR systems is visible in a vast number of applications in science and industry. Low-field nuclear magnetic resonance (LF-NMR) became an instant in technologies that productions are dependent on the reliable structure identification, grade and purity control, chemical process inspection or reaction monitoring. Beyond the benefits of being cost-, space-, maintenance- and user friendly, insufficient sensitivity and low signal resolution are the main drawbacks, due to which the low-field NMR (LF-NMR) in the fields of organic chemistry and synthesis remains limited to solely academic teaching purposes. Herein, we discuss the possibilities of LF-NMR for the needs of organic chemistry and synthesis on a set of compounds 1-4 achieved as the products of student’s laboratory course and organic derivatives 5-8 that are from our research interests. Chemical structure determination of all compounds 1-8 presented herein was performed using the benchtop-type NMR instrument operating at 60 MHz (Pulsar Oxford Ltd.). Structure of novel compounds 5-7 prepared under the aims of our research was characterized by combined 1H/19LF-NMR and compared with an appropriate high-field NMR data from Bruker Ascend Instrument (400 MHz). Finally, possibilities of the low-field NMR as an analytical tool for the research purposes in the fields of organic chemistry and synthesis are documented on a set of 1H and 2D 1H-1H COSY for azomethine 8.

A superior variant of dried jujube in China is ‘Huizao’ (HZ) jujube. Nonetheless, detailed evaluations of the texture quality of HZ fruits have been the subject of few studies. Texture is a significant indicator of the sensory and processed quality of a fruit. Here, we differentiate and characterize the texture quality of HZ fruits from the four primary producing regions in southern Xinjiang, as well as develop a system for assessing the texture quality of HZ fruits. Furthermore, five texture indices of HZ fruits from 109 plantations were exhaustively evaluated utilizing principal component analysis, Pearson correlation analysis, and hierarchical clustering analysis. Consequently, by the 10th, 30th, 70th, and 90th percentiles, each index was classified into five grades—lower, medium, high, and higher. Correlation investigation indicated strong relationships between the springiness, chewiness, cohesiveness, gumminess, and hardness of HZ fruits. Springiness, hardness, and adhesiveness are essential indicators that influence the texture of HZ fruits. We used clustering analysis to separate the six texture indices into three major categories (hard factor, stick-elastic factor, and adhesive factor), with indices representing hardness, springiness, and adhesiveness, respectively. Furthermore, according to the factor molecules, the texture quality of HZ fruits in the four production areas was evaluated as Bazhou (1.24) > Hotan (0.773) > Kashi (-0.577) > Aksu (-0.852). RDA analysis of six texture quality parameters and 24 climate conditions identified higher mean temperature (TEM) and lower relative humidity (RHU) as the primary factors contributing to the improved texture quality of HZ fruits in Xinjiang. This study identified the texture quality characteristics of HZ fruits in four major producing areas of Southern Xinjiang, and it offered a theoretical foundation for optimizing the dominant producing areas and regional production of HZ varieties in Xinjiang.

Relativistic shocks are one of the most plausible sites of the emission of strongly variable, polarized multi-wavelength emission from relativistic jet sources such as blazars, via diffusive shock acceleration (DSA) of relativistic particles. This paper summarizes recent results on a self-consistent coupling of diffusive shock acceleration and radiation transfer in blazar jets. We demonstrate that the observed spectral energy distributions (SEDs) of blazars strongly constrain the nature of hydromagnetic turbulence responsible for pitch-angle scattering by requiring a strongly energy-dependent pitch-angle mean free path. The prominent soft X-ray excess (``Big Blue Bump'') in the SED of the BL Lac object AO 0235+164 can be modelled as the signature of bulk Compton scattering of external radiation fields by the thermal electron population, which places additional constraints on the level of hydromagnetic turbulence. It has further been demonstrated that internal shocks propagating in a jet pervaded by a helical magnetic field naturally produce polarization-angle swings by 180$^o$, in tandem with multi-wavelength flaring activity, without requiring any helical motion paths or other asymmetric jet structures. The specific application of this model to 3C279 presents the first consistent, simultaneous modeling of snap-shot SEDs, multi-wavelength light curves and time-dependent polarization signatures of a blazar during a polarization-angle (PA) rotation. This model has recently been generalized to a lepto-hadronic model, in which the high-energy emission is dominated by proton synchrotron radiation. It is shown that in this case, the high-energy (X-ray and $\gamma$-ray) polarization signatures are expected to be significantly more stable (not showing PA rotations) than the low-energy (electron-synchrotron) signatures.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

Weak signal spectral detection is a serious problem in many applications, especially the target possesses certain frequency band and under low signal-to-noise ratio (SNR). A kind of novel technique based on pre-whitening scale-transformation symmetric bistable parallel stochastic resonance (SR) is proposed to solve the problem. Firstly, the pre-whitening can ensure the even distribution of the receiving signal to fit the requirement of SR processing. Secondly, the scale- transformation can help to utilize the weak signal improvement property especially under low frequency band more effectively. Thirdly, the symmetric bistable parallel SR can try to reduce the variance of the clutter and additive noise fluently. Fourthly, by subtracting the steady state re-sponse of the selected symmetric bistable SR system from the parallel SR output, the weak signal spectral detection objective can be realized successfully. Simulation results based on the real sea clutter radar data guarantee the effectiveness and applicability of the proposed symmetric bistable PSR processing approach.

The goal of farmers operating in a market economy is to maximise profit. In the face of the changing political situation, the main social interest, besides food security, should be energy security. This article aims to indicate the direction of agricultural policy development so that it guarantees both the economic security of producers—farmers—and Europe’s energy security. The work uses data obtained from the agri benchmark Cash Crop database. DEA method and stepwise multiple regression were used. The research showed that plants are already grown in Europe which will ensure high energy efficiency of production without compromising farm financial results (including oats, peas and winter rye) and that improving the involvement of certain inputs results in improved production efficiency (among others, by expenditure on agricultural advisory services). The significance of the presented research results from the fact that the recent COVID pandemic and escalation of the military conflict in Ukraine have led to a renewed interest in the concept of EU energy security, i.e. generation of generating the greatest possible amount of energy within the EU, to be used both for food and non-food purposes.

Recent analyses of cosmic microwave background surveys have revealed hints that there may be a non-trivial running of the running of the spectral index. If future experiments were to confirm these hints, it would prove a powerful discriminator of inflationary models, ruling out simple single field models. We discuss how isocurvature perturbations in multi-field models can be invoked to generate large runnings in a non-standard hierarchy, and find that a minimal model capable of practically realising this would be a two-field model with a non-canonical kinetic structure. We also consider alternative scenarios such as variable speed of light models and canonical quantum gravity effects and their implications for runnings of the spectral index.

The relentless advancement and integration of mechanization and intelligence within the coal mining industry, combined with the increasing depths of mining operations, necessitate significantly higher safety standards. This necessity arises due to the increasingly complex geological and coal seam conditions encountered as mining operations delve deeper into the earth. Traditionally, 3D seismic exploration technology has been fundamental in ensuring both operational efficiency and safety in the coal mining sector. However, despite its critical role, this technology still has limitations in detecting and characterizing small-scale geological structures which can pose substantial risks if not accurately identified and mitigated. To address these challenges, this paper introduces a sparsity-constrained adaptive hard thresholding algorithm designed to tackle the spectral inversion optimization problem with an norm constraint for the enhanced retrieval of reflection coefficients, thereby establishing a comprehensive workflow for enhancing seismic data resolution through compressed sensing spectral inversion. Real data validation has demonstrated that this method significantly enhances the resolution of seismic data while maintaining the amplitude integrity and fidelity of the original signals. This improvement allows for a more detailed and accurate characterization of small-scale geological features, which are critical in identifying and mitigating potential hazards within coal mining operations, thus offering robust support for the implementation of more effective safety protocols and disaster prevention strategies in coal mines.

The publication presents an innovative tower cultivation device designed to significantly increase vertical farming efficiency. The device divides the cultivation system into separate chambers. One division corresponds to the different growth phases of the plants, while another reflects the daily variation in conditions. Each chamber presents slightly different conditions and cultivation patterns from the others. For the early stages, crops are grown horizontally in trays once they mature, transplanted into mobile cultivation towers. The closed circulation of ventilation and irrigation reduces water consumption by up to 95%. A unique separate day-night division optimises light, temperature and humidity conditions, mimicking natural growth patterns. This approach not only saves water and energy but also optimises cultivation in a three-dimensional space. The presented solution focuses on the often overlooked aspects of cultivating in vertical farms and makes this method of growing much more cost-effective and feasible to implement on a large scale.

In this study, a novel method is proposed to estimate surface-spectral reflectance from camera responses that combines model-based and training-based approaches. An imaging system is modeled using the spectral sensitivity functions of an RGB camera, spectral power distributions of multiple light sources, unknown surface-spectral reflectance, additive noise, and a gain parameter. The estimation procedure comprises two main stages: (1) selecting the local optimal reflectance dataset from a reflectance database and (2) determining the best estimate by applying a neural network to the local optimal dataset only. In stage (1), the camera responses are predicted for the respective reflectances in the database, and the optimal candidates are selected in the order of lowest prediction error. In stage (2), most reflectance training data are obtained by a convex linear combination of local optimal data using weighting coefficients based on random numbers. A feed-forward neural network with one hidden layer is used to map the observation space onto the spectral reflectance space. In addition, the reflectance estimation is repeated by generating multiple sets of random numbers, and the median of a set of estimated reflectances is determined as the final estimate of the reflectance. Experimental results show that the estimation accuracies exceed those of other methods.

The efficacy of predicting geochemical parameters with a 2-chain workflow using spectral data as the initial input is evaluated. Spectral measurements spanning the approximate 400-25000nm spectral range are used to train a workflow consisting of a non-negative matrix function (NMF) step, for data reduction, and a random forest regression (RFR) to predict 8 geochemical parameters. Approximately 175000 spectra with their corresponding chemical analysis were available for training, testing and validation purposes. The samples and their spectral and chemical parameters represent 9399 drillcore. Of those, approximately 20000 spectra and their accompanying analysis were used for training and 5000 for model validation. The remaining pairwise data (150000 samples) were used for testing of the method. The data are distributed over 2 large spatial extents (980 km2 and 3025 km2 respectively) and allowed the proposed method to be tested against samples that are spatially distant from the initial training points. Global R2 scores and wt.% RMSE on the 150000 validation samples are Fe(0.95/3.01), SiO2(0.96/3.77), Al2O3(0.92/1.27), TiO(0.68/0.13), CaO(0.89/0.41), MgO(0.87/0.35), K2O(0.65/0.21) and LOI(0.90/1.14), given as Parameter(R2/RMSE), and demonstrate that the proposed method is capable of predicting the 8 parameters and is stable enough, in the environment tested, to extend beyond the training sets initial spatial location.

The study employed simulation-based measurement approaches to evaluate and compare the performance of conventional networks to IRS-enhanced systems in terms of upstream spectral efficiency. The study discovered that applying IRS greatly improves coverage, or transmitting potency, for 6G services.

The optimal functionality and dependability of mechanical systems are important for the sustained productivity and operational reliability of industrial machinery which has direct impact on it’s longevity and profitability. Therefore, failure of a mechanical system or any of it component would be detrimental to production continuity and availability. Consequently,this study proposes a robust diagnostic framework for analyzing the blade conditions of shot blast industrial machinery. The framework involves analyzing the spectral characteristics of the vibration signals generated by Industrial Shot Blast. Additionally, a peak detection algorithms is introduced to identify and extract the unique features present in the peak magnitudes of each signal spectrum. A feature importance algorithm is then deployed as the feature selection tool, and these selected features are fed into 10 machine learning classifier, with Extreme gradient boosting (XGB) as the core classifier. Results show that the XGB classifier achieved the best accuracy of 98.05%, with a cost-efficient computational cost of 0.83 seconds. Other global assessment metrics were also implemented in the study to further validate the model.

The present study aims to measure the technical efficiency and establish core factors effecting rice production in Cambodia. Four-years dataset generated from the central government document “Profile on Economics and Social” of entire 25 provinces between 2012-2015 and the stochastic production frontier model (SFA) was applied. The results indicated that the level of output (quantity) of Cambodian rice production varied according to the different level of capital investment in agricultural machineries, total rice actual harvested area, and technically fertilizers application within provinces. Furthermore, evidence revealed the overall mean efficiency of rice production is 78.4% implies that there is still room to further improve technical efficiency by given the same level of inputs and technology. More importantly, the findings revealed that irrigation, production technique and amount of agricultural supporting staffs are being as the most important influencing factors of rice production’s technical efficiency in Cambodia. In conclusion, present study strongly recommends the development of irrigation systems and good water management practices to be considered and bring into more effective actions by the central government as well as related agencies for improving rice production in Cambodia in addition to capital investment and improving technical skills of supporting staffs and rural farmers.

As a renewable industrial crop, Miscanthus offers numerous advantages, namely high photosynthesis activity (as a C4 plant) and exceptional CO2 fixation rate. These properties make Miscanthus very attractive for industrial exploitation, such as lignin generation. Here, we present a systematic study analyzing the correlation of the lignin structure with Miscanthus genotype and plant portion (stem versus leaf). Specifically, the ratio of the three monolignols and corresponding building blocks as well as the linkages formed between the units have been studied. Depending on the Miscanthus genotype and plant component (leaf versus stem), correlations between chemical structure and properties of the lignins have been determined, i.e. correlations in molecular weight, polydispersity and decomposition temperature. Lignin isolation was performed using non-catalyzed organosolv pulping and the structure analysis includes NREL, FTIR, UV-Vis, HSQC-NMR, TGA, pyrolysis GC/MS. Structural differences were found for stem and leaf-derived lignins. Compared to beech wood lignins, Miscanthus lignins possess lower molecular weight and narrow polydispersities (< 1.5 Miscanthus vs. > 2.5 beech) corresponding to improved homogeneity. In addition to conventional univariate analysis of FTIR spectra, multivariate chemometrics revealed distinct differences for aromatic in-plane deformations of stem versus leaf-derived lignins. These results emphasize the potential of Miscanthus as low-input resource and Miscanthus-derived lignin as promising agricultural feedstock.

The production of recombinant proteins in Escherichia coli is often challenged by cytoplasmic expression due to proteolytic degradation and inclusion body formation. Extracellular expression can overcome these problems by simplifying downstream processing and improving protein yields. This study aims to compare the efficiency of two Bacillus subtilis chitosanase signal peptides in mediating extracellular secretion in E. coli. We identified a naturally occurring mutant signal peptide (mCsn2-SP) from B. subtilis CH2 chitosanase (CH2CSN), which is characterized by a deletion of six amino acids in the N-region relative to the signal peptide (Csn1-SP) from B. subtilis CH1 chitosanase (CH1CSN). The CH1CSN and CH2CSN genes were cloned into the pET-11a vector and protein secretion was evaluated in E. coli BL21(DE3) host cells. Expression was induced with 0.1 mM and 1 mM IPTG at 30°C for one and three days. CH2CSN showed higher secretion levels compared to CH1CSN under all experimental conditions, especially with 0.1 mM IPTG induction for 3 days, which resulted in a 2.37-fold increase in secretion. These results suggest that signal peptide deletion variants may have an effect on protein secretion efficiency and help to further understand the function of signal peptides.

This study describes a novel method for grading pathological sections of gliomas. Our own integrated hyperspectral imaging system was employed to characterize 270 bands of cancerous tissue samples from microarray slides of gliomas. These samples were then classified according to the guidelines developed by the World Health Organization, which define the subtypes and grades of diffuse gliomas. We explored a hyperspectral feature extraction model called SMLME-Resnet using microscopic hyperspectral images of brain gliomas of different malignancy grades. The model combines the channel attention mechanism and multi-scale image features to automatically learn the pathological organization of gliomas and obtain hierarchical feature representations, effectively removing the interference of redundant information. It also completes multi-modal, multi-scale spatial and spectral feature extraction to improve the automatic classification of glioma subtypes. The proposed classification method demonstrated high average classification accuracy (>97.3\%) and Kappa coefficient (0.954), indicating its effectiveness in improving the automatic classification of hyperspectral gliomas. The method is readily applicable in a wide range of clinical settings, offering valuable assistance in alleviating the workload of clinical pathologists. Furthermore, the study contributes to the development of more personalized and refined treatment plans, as well as subsequent follow-up and adjustment of treatment, by providing physicians with insights into the underlying pathological organization of gliomas.

In recent times, the application areas of unmanned aerial vehicles (UAVs) are expanding, and autonomous functions are becoming increasingly prominent, eliminating the need for remote pilot control. Certain applications require the drone to use a docking station autonomously, even for wireless charging. This involves performing autonomous takeoff and landing, where high preci-sion is demanded. These maneuvers can be significantly influenced by environmental factors. The effectiveness of the precision landing function of the DJI Mavic 2 Pro UAV in strong winds is in-vestigated in this article based on experimental measurements conducted outdoors. New findings on the precision landing capabilities of the DJI Mavic 2 Pro UAV are presented in this paper, par-ticularly under windy conditions. The efficiency of precision landing is compared in cases when the precision landing function is enabled versus when it is disabled. It is investigated whether there is a statistically significant difference between the two landing modes in strong winds and it is examined whether the DJI Mavic 2 Pro can perform precision landing on a surface of a specific size in windy conditions. This helps to predict the suitability of the DJI Mavic 2 Pro for precise landing and wireless charging at a docking station in strong winds and high gusts.

The fracture strength was compared in a scratch test of coatings based on the ZrN system with the introduction of Ti, Nb and Hf, which were deposited on a titanium alloy substrate. The coatings were deposited using Controlled Accelerated Arc (CAA-PVD) technology. The comparison was carried out according to two parameters: adhesion strength to the substrate and overall coating strength. The (Zr,Hf)N coating showed better resistance to destruction, but had worse adhesion to the substrate. As a result, although the coating is retained directly in the scribing groove, a large area of delamination and destruction is formed around the groove. The (Ti,Zr,Nb)N coating, with its somewhat lower strength, has high adhesion to the substrate; no noticeable delamination is observed along the groove boundary.

A Q-switched Nd:YAG laser was focused on Pb-Ti alloy samples in several Laser Induced Breakdown experiments in order to measure the Stark parameters of several spectral lines (58) of single ionized Titanium including the 3504.89 Å, and the 3510.83 Ålines (where we aported new experimental and theoretical values).Diagnostics of the laser induced plasmas (electron density and electron temperature) was performed using Balmer’s H alpha line (6562.7 Å).Temperatures were obtained by the Boltzmann Plot technique with spectral lines of Pb I (after correction for its evident self-absorption).Subsequently, calculations by the Griem approach of the Stark broadening parameters for several spectral lines were performed using the Gaunt factors proposed by Van Regemorter and those proposed by Douglas H. Sampson. In the latter cases the values obtained were very close to the experimental values. It allows us to assume that the calculations made for the spectral lines of Ti II, without experimental information, are more accurate using the Gaunt factors proposed by Sampson.

In the process of oil and gas development and production, when the flow rate in the wellbore is large, the materials underground will be eroded, causing the operation to be unable to proceed smoothly and reducing the efficiency of oil and gas production. Therefore, optimizing the anti-erosion coating under high-speed flow conditions in wellbore is a very interesting thing. It can greatly improve operational efficiency. In this paper, laser cladding was used to prepare the new coating used in the PDC drill bit. Then, the effects of tungsten carbide and multi-layer graphene on the microstructure and properties of the tungsten carbide coating were studied. The research results indicate that, for new coatings, 60% tungsten carbide and 0.3% graphene are the optimal ratios. After adding WC, the hardness has significantly improved. However, when the WC content further increases more than 30%, the increase in hardness is relatively small. In addition, when the content of graphene is more than 0.3%, the branched structure became thicker, and not only the segregation of Cr, Si and W became very obvious again, but also the segregation of Fe occurred at the Ni enrichment site. The research results contribute to improving oil and gas production and operational efficiency under high-speed fluid flow conditions in the wellbore.

The principal aim of a spectral observer is twofold: the reconstruction of a signal of time via state estimation and the decomposition of such a signal into the frequencies that make it up. A spectral observer can be catalogued as an online algorithm for time-frequency analysis because is a method that can compute on the fly the Fourier transform (FT) of a signal, without having the entire signal available from the start. In this regard, this paper presents a novel spectral observer with an adjustable constant gain for reconstructing a given signal by means of the recursive identification of the coefficients of a Fourier series. The reconstruction or estimation of a signal in the context of this work means to find the coefficients of a linear combination of sines a cosines that fits a signal such that it can be reproduced. The design procedure of the spectral observer is presented along with the following applications: (1) the reconstruction of a simple periodical signal, (2) the approximation of both a square and a triangular signal, (3) the edge detection in signals by using the Fourier coefficients, (4) the fitting of the historical Bitcoin market data from 2014-12-01 to 2018-01-08 and (5) the estimation of a input force acting upon a Duffing oscillator. To round out this paper, we present a detailed discussion about the results of the applications as well as a comparative analysis of the proposed spectral observer vis-à-vis the Short Time Fourier Transform (STFT), which is a well-known method for time-frequency analysis.

In response to the fairness issue arising from the unequal delay of vehicles in different phases at intersections, considering the actual situation of small and variable delays for vehicles in low-saturation intersection phases, this paper proposes the concept of "sacrificing efficiency for fairness." Firstly, the universality of unfair delay phenomena at intersection phases is explained, especially at low-saturation intersections where the fluctuation in phase delays is 1.87 times higher than at other intersections. Then, a fairness evaluation index is constructed using information entropy, and the feasibility of the proposed approach is demonstrated. Subsequently, a signal optimization model that balances efficiency and fairness is proposed. Finally, the proposed model is validated through case studies, showing that it not only simultaneously considers efficiency and fairness but also has minimal impact on efficiency. Moreover, the changes to timing schemes in the efficiency model are much smaller compared to the model that only considers fairness. Sensitivity analysis reveals that the model performs better under low-saturation intersection conditions.

Forests have multifunctional roles. They not only increase forest carbon sinks through afforestation and management, but also indirectly realize multiple benefits of "economy + ecology + society". Therefore, we construct a multiple output-benefit system of forest carbon sinks based on the development of forest carbon sinks in provinces of China. This system is also able to distinguish the importance of forest carbon sinks from other outputs. For the efficiency evaluation of multi-level output systems, this paper constructs a cross-evaluation model based on evidential reasoning method, the original efficiency information by conducting efficiency evaluation before information fusion. Further, the spillover effects and influencing factors of forest carbon sink efficiency are analyzed through a spatial regression model to explore the spatial characteristics of forest carbon sink efficiency in China. The results show that: (1) there is a large gap between the cross-efficiency levels of forest carbon sinks in various regions of China, with significant spatial correlation. For the perspective of direct output benefits, the cross-efficiency of the eastern region is higher, while the cross-efficiency of the northwestern region is lower; for the perspective of indirect output benefits, the cross-efficiency of the southeastern region is higher. (2) China's forest carbon sink has a significant positive spillover effect, and the indirect output cross-efficiency has a significant negative impact on the forest carbon sink in its own region. Further analyzing the impact of indirect output cross-efficiency, it is found that the cross-efficiency of the ecological dimension and the cross-efficiency of the social dimension have a significant negative impact on the forest carbon sink in its own region, and the economic dimension has a significant positive impact on the forest carbon sink in its own region. In conclusion, corresponding policy recommendations are proposed for the development of forest carbon sinks to promote the realization of the dual-carbon goal.

Water scarcity, particularly in arid and semi-arid regions, poses a significant challenge to crop production, with drought being a prevalent factor limiting grain production globally. Enhancing agricultural water use efficiency is crucial for managing water resources effectively in these areas. Water resource management involves planning, developing, distributing, and optimizing the use of water resources. Water use efficiency management is also essential for crop growth in arid regions. Various agronomic and irrigation strategies can improve crop water use efficiency and drought tolerance. The primary goal of these strategies is to maximize irrigation efficiencies by applying the precise amount of water needed to restore soil moisture to the desired level. These sustainable practices not only reduce the cost of water and labor for farmers through reduced irrigation but also optimize the use of soil moisture storage. This review paper explores practical techniques to improve water use efficiency, highlighting the role of nutrients in enhancing water use efficiency in crop plants.

This paper provides a comparative analysis of AES (Advanced Encryption Standard) and Salsa20 algorithm implementations, focusing on power consumption efficiency in passive RFID (Radio Frequency Identification) tags and ultra-low-power devices. The main objective of this work is to determine which of these algorithms is more suitable to operate in these types of devices. For this purpose, ASIC (Application-Specific Integrated Circuit) implementations of AES and Salsa20 based on low-power approaches were developed and their power consumption was evaluated. Results demonstrate that Salsa20 power consumption is lower than AES (2.82μW and 4.01μW, respectively - both in 0.18μm), indicating that Salsa20 is a better choice than AES for passive RFID tags.

Aerial image classification has become popular and has attracted extensive research efforts in recent decades. The main challenge lies in its very high spatial resolution but relatively insufficient spectral information. To this end, spatial-spectral feature extraction is a popular strategy for classification. However, parameter determination for that feature extraction is usually time-consuming and depends excessively on experience. In this paper, an automatic spatial feature extraction approach based on image raster and segmental vector data cross-analysis is proposed for the classification of very high spatial resolution (VHSR) aerial imagery. First, multi-resolution segmentation is used to generate strongly homogeneous image objects and extract corresponding vectors. Then, to automatically explore the region of a ground target, two rules, which are derived from Tobler’s First Law of Geography (TFL) and a topological relationship of vector data, are integrated to constrain the extension of a region around a central object. Third, the shape and size of the extended region are described. A final classification map is achieved through a supervised classifier using shape, size, and spectral features. Experiments on three real aerial images of VHSR (0.1 to 0.32 m) are done to evaluate effectiveness and robustness of the proposed approach. Comparisons to state-of-the-art methods demonstrate the superiority of the proposed method in VHSR image classification.

Mineral nutrition is essential for plant growth and interaction of plants with biotic and abiotic stresses. Mango twig-tip dieback (MTTD) is a new type of mango decline, but its impact on the trees’ mineral nutrition is unknown. This study was conducted to determine the effect of MTTD infection on the nutrient status, balance, and resorption efficiency (RE) of mango. Leaf nutrient concentrations and deviation from the optimum percentage (DOP) indices of ‘Kensington Pride’ (KP) mango trees with low (LD) and high (HD) levels of MTTD infections were analyzed to compare the foliar nutrition status and nutrient balance between the LD and HD trees. Moreover, the nutrient resorption efficiency of MTTD-infected dried leaves (RE_D) was compared with the resorption efficiency of healthy (RE_S) leaves of KP mangoes. The concentrations of the total Ca, Mg, Cu, Fe, Mn, and Zn were lower in the HD trees than in the LD trees. But the total K content was higher in the HD trees, and its DOP index was sufficient, while the total K concentration was low and deficient level in LD trees. Moreover, DOP indices for total Ca, Mn, and Zn were less deficient in LD trees than in HD trees, and overall nutrient imbalances were exacerbated in HD trees. RE_D was significantly lower than RE_S for the total N, P, S, Cu, Fe, and Zn but significantly higher than RE_S for K. The study underscores the significant influence of MTTD on the mineral nutrition of KP mangoes, revealing distinct nutrient variations between trees with low and high MTTD infection levels. These findings have important implications for mango crop management, emphasizing the need for targeted nutrient interventions to address imbalances induced by MTTD and enhance the overall health and resistance of mango trees against MTTD infection.

Background: Depression presents with altered energy regulation and neural plasticity. Previous electroencephalography (EEG) studies showed that practice increases power in beta range (13-30 Hz) in healthy subjects but not in those with impaired plasticity. Here, we ascertain whether depression presents with alterations of spectral activity and connectivity before and after practice. Methods: We used publicly available resting state EEG (64 electrodes) of 122 subjects. Based on Beck Depression Inventory (BDI) score, they were assigned to either high BDI (hBDI, BDI&gt;13, N=46) or control (CTL, BDI&lt;7, N=75) group. We analyzed spectral activity, theta-beta and theta-gamma phase-amplitude coupling (PAC) of EEG recorded before and after a learning task. Results: At baseline, compared to CTL, hBDI group exhibited greater beta power over fronto-parietal regions and gamma over right parieto-occipital area. After practice, increases in all frequency ranges were observed only in CTL. Theta-beta and theta-gamma PAC were greater in hBDI before the task but not after the task. Conclusions: The lack of substantial post-task growth of beta power in depressed subjects likely represents power saturation due to greater baseline values. We speculate that inhibitory/excitatory imbalance, altered plasticity mechanisms, and energy dysregulation present in depression may contribute to this phenomenon.

Quasi-solid composited electrolytes were produced by LiFSI initiated polymerized poly-(Dioxolane) (PDOL) with garnet-LLZO (Li7La2Zr3O12) nanofibers and used in lithium-metal batteries. Linear sweep voltammetry shows that the initial oxidation voltage of 4.6 V for Gel-10% (G10, 10% wt. LLZO in PDOL) vs Li/Li+. EIS test of stainless steel// stainless steel symmetric cells for Gel-1% (G1), Gel-5% (G5) and Gel-10% (G10) show ion conductivity (5*10-5 S/cm). Li/G10/Li symmetric cells have stable stripping-plating cycling performance over 1300 hours continuously with the current density of 0.1 mA/cm2 at 25 oC, indicating a good interface contact and stable lithium-ion transport pathway through the composite electrolytes. LFP/G10/Li batteries have stable charge-discharge plateau, low polarization voltage of 0.07-volt, energy efficiency of 95% and coulombic efficiency of ~99% at current density of 26.3 mA/g at 25 oC for over 100 cycles.

The changing of banking customer preferences after Covid-19 pandemic encourages banking transformation. Neobanks emerges as innovation in banking that enter the market to compete with the incumbent banks by offering new digital experience for customer. This paper analyzes the neobanks which transformed from traditional bank, specifically its efficiency after they implement digital transformation. Efficiency is measured by using Stochastic Frontier Analysis (SFA). This study also uses Pooled Mean Group (PMG) of Panel ARDL (Autoregressive Distributed Lagged) to investigate digital transformation as one of determinants neobank’s efficiency, as well as to examine the existence of short-term and long-term relationship between digital transformation and efficiency. The SFA results show that the efficiency of the neobanks increase after they carry out digital transformation. Furthermore, from PMG Panel ARDL, it can be concluded that digital transformation is one of determinant of efficiency and there is longevity relationship between digital transformation and efficiency. In the short run, digital transformation has a significant and negative correlation with efficiency and in the long run, it has a significant positive relationship because initially digital transformation cost for operational and risk management innovation decreases the profit efficiency, but afterwards it increases the profit efficiency.

The article presents the results of cyanide leaching of gold-containing concentrate using the trichlorocyanuric acid (TCCA) oxidizer. Gold-containing concentrate obtained from a gold tailings sample from a gold recovery factory (GRF) in one of the deposits of Kazakhstan that was not previously studied for concentrability. According to X-ray phase analysis and energy dispersive spectrometry (DSM) data, the main compounds in the tailings sample under study are: pyrite FeS2, quartz SiO2, calcite CaCO3, albite NaAlSi3O8, muscovite KAl2Si3AlO10(OH)8, dolomite CaMg(CO3)2, and oxidized iron compounds. Microscopic studies have established the presence of gold grains in free form, ranging in size from 0.9-10.2 mkm Au-ultrafine and fine gold. Obtaining a gold-containg concentrate with a gold content of 15.95 g / t is possible according to the enrichment scheme, which includes centrifugal separation, classification according to the fineness class -0.05 mm, additional grinding of hydrocyclone sands to a fineness of 90.0-95.0% of the class finer than 0.050 mm, and control centrifugal separation. Since pyrite in technogenic raw materials is the main gold-containing mineral, this paper presents studies on the oxidizability of pyrite with the TCCA oxidizer. The results of studies on the oxidation of pyrite using the TCCA oxidizer show that the products of its hydrolysis oxidize pyrite with the formation of various iron compounds on its surface. Pretreatment of gold-containing concentrate with oxidizer TCCA for 3 hours before the cyanidation process (20 hours) allows to increase the recovery of gold in the solution by 5.8 %.

This article continues research efforts on performance and energy efficiency of intelligent algorithms and its role for green and sustainable computing. The introduction focusses on Bremermann's Limit and its effect on extensive approach for improvement of computers performance. The article aims to identify role of Intelligent Algorithms energy efficiency, how it differs from general software energy efficiency. An improved empirical investigation on heuristic methods for search and optimisation illustrates algorithms' energy efficiency. Experimental results and consideration of further work conclude the article.

Developments in artificial intelligence techniques allow for an improvement in sustainable mobility strategies with particular reference to energy consumption estimates of electric vehicles (EVs). This research proposes a vehicle energy model developed on the basis of Deep Neural Network (DNN) technology. The study also explores the potential application of the model developed for the movement data of new vehicles in the province of Enna, Sicily, Italy. which is characterized by numerous attractors and the increasing number of hybrid and electric cars circulating. The energy model for electric vehicles shows high accuracy and versatility, requiring vehicle velocity and acceleration as input data to predict energy consumption. The research article also provides recommendations for the energy modeling of electric vehicles and outlines additional steps for model development. The implemented methodological approach and its results can be used by transport decision makers to plan new transport policies in Italian cities aimed at optimizing vehicle charging infrastructure. They can also help vehicle users accurately estimate energy consumption, generate maps, and identify locations with the highest energy consumption.

The need for integrated high-frequency systems has increased significantly, leading to the development of efficient antennas operating in the 0.1-10 terahertz (THz) range. Using graphene as the conducting 2D material and hexagonal boron nitride (hBN) as the dielectric substrate, this research effort examines the design and performance evaluation of a THz band antenna functioning on supporting nanotechnology. The researchers contrasted the system’s performance with the 6G wireless network requirements after analyzing the antenna performance, radiation patterns, and impedance matching. According to this research, graphene, along with hBN can enhance antenna performance overall in the THz band and open pathways for advanced communication. The application of the designed antenna in a 6G wireless network will be tested through um MIMO configuration to achieve a higher data rate.

Technological equipment in quarries that extract and deliver aggregates for different uses operates in a predetermined flow depending on the type of rocks exploited and the dimensional characteristics imposed on the final products. In this context, the interruptions in operation required to replace high-wear parts (such as the teeth of excavators and bucket loaders) must be limited as much as possible through technological solutions to increase their service life. The evolution of the wear of the teeth of the quarry equipment that come into direct contact with the rocks was concretely established in the production process, in parallel with the wear values obtained by simulating the wear phenomenon in laboratory conditions, in order to validate the data collected during the operation of the machines. Preventive-repetitive maintenance, within the activities of reconditioning the worn surfaces of the teeth, through the charging process by manual electric welding with covered electrodes, was applied directly to the machine, which led to the shortening of the interruptions in operation necessary to replace these spare parts.

Despite energy-related financial concerns and the growing demand for sustainability, many energy efficiency measures are not being implemented in industrial practice. There are a number of reasons for this, including a lack of knowledge about energy efficiency potentials and the assessment of energy savings as well as the high workloads of employees. This article describes the systematic development of an expert system, which offers a chance to overcome these obstacles and contribute significantly to increasing the energy efficiency of production machines. The system employs data-driven regression models to identify inefficient parameter settings, calculate achievable energy savings, and prioritize actions based on a fuzzy rule base. Proposed measures are first applied to an analytical real-time simulation model of a production machine to verify that constraints required for the specified product quality are met. This provides the machine operator with the expert means to apply proposed energy efficiency measures to the physical entity. We demonstrate the development and application of the system for a throughput parts cleaning machine in the metalworking industry.

In this study, seventeen faceted gem-quality chrysoberyls exhibiting an attractive canary yellow color were investigated by a series of gemological, spectral, and chemical methods. Microscopic observation reveals distinct growth lines and inclusions, including CO2 fluids, carbon, and mineral crystals such as calcite, quartz, sillimanite, and mica, identified by the Raman spectrum. The FTIR spectrum exhibits the 2405 and 2160 cm-1 feature peaks and a 3223 cm-1 peak in all samples, which can be accompanied by the 3112 cm-1 shoulder, 3301, and 3412 and 3432 cm-1 peaks. The UV-Vis spectrum shows a Fe-related peak at 440 nm, along with the 650–660 nm band and the absorption band in the blue zone of the visible light. The chemical results of EDXRF reveal a V-poor, Cr-poor, and Fe-rich feature. The spectral and chemical results could contribute to explaining the origin of the canary yellow color, which originates from the abundant amount of Fe with very little influence from Cr or V.

The diffraction-like process displayed by a spatially localized matter wave is here analyzed in a case where the free evolution is frustrated by the presence of hard-wall-type boundaries (beyond the initial localization region). The phenomenon is investigated in the context of a nonrelativistic, spinless particle with mass m confined in a one-dimensional box, combining the spectral decomposition of the initially localized wave function (treated as a coherent superposition of energy eigenfunctions) with a dynamical analysis based on the hydrodynamic or Bohmian formulation of quantum mechanics. Actually, such a decomposition has been used to devise a simple and efficient analytical algorithm that simplifies the computation of velocity fields (flows) and trajectories. As it is shown, the development of space-time patters inside the cavity depends on three key elements: the shape of the initial wave function, the mass of the particle considered, and the relative extension of the initial state with respect to the total length spanned by the cavity. From the spectral decomposition it is possible to identify how each one of these elements contribute to the localized matter wave and its evolution; the Bohmian analysis, on the other hand, reveals aspects connected to the diffraction dynamics and the subsequent appearance of interference traits, particularly recurrences and full revivals of the initial state, which constitute the source of the characteristic symmetries displayed by these patterns. It is also found that, because of the presence of confining boundaries, even in cases of increasingly large box lengths, no Fraunhofer-like diffraction features can be observed, as happens when the same wave evolves in free space. Although the analysis here is applied to matter waves, its methodology and conclusions are also applicable to confined modes of electromagnetic radiation (e.g., light propagating through optical fibers).

Additives for anaerobic digestion (AD) can play a significant role in optimising the process by increasing biogas production, stabilising the system and improving digestate quality. The role of additives largely boils down to: (i) enhancing direct interspecies electron transfer (DIET) between microbial communities, resulting in improved syntrophic interactions and methane production rates (e.g. biochar, magnetite and carbon nanotubes), (ii) adsorption of toxic substances that may inhibit microbial activity (e.g. activated carbon, zeolites), (iii) improving microbial activity and increasing process stability (e.g. cobalt, nickel, iron, selenium), (iv) maintaining optimal pH levels for microbial activity (e.g. magnesium oxide), (v) reducing inhibition (the aforementioned adsorbents and conductive substances), (vi) accelerating the decomposition of complex organic materials into simpler compounds that are more easily digested by microorganisms, thereby increasing the rate of hydrolysis (enzymes, including cellulases, proteases and lipases). Through the aforementioned action, additives can significantly affect AD performance. The function of these materials varies, from enhancing microbial activity to maintaining optimal conditions and protecting the system from inhibitors. The choice of additives should be carefully tailored to the specific needs and conditions of the digester to maximise benefits and ensure sustainability. In light of these considerations, this paper characterizes the most commonly used additives and their combinations based on a comprehensive review of recent scientific publications, including a report on the results of conducted studies. The publication features chapters that describe: carbon-based conductive materials, metal oxide nanomaterials, trace metal and biological additives, including enzymes and microorganisms. It concludes with a chapter summarising reports on various additives and discussing their indications for functional systems with determined properties. A notable advantage of this work is the updated literature data, clear summaries, and a substantive description of the performance of the additives discussed.

This study concerns the transport and retention of polydisperse micron-sized (16 ± 6 µm) of microplastics (MPls) in porous media under varying flow rate conditions. Sorption kinetics were modeled using first-order reversible and irreversible kinetic sorption models, with sensitivity analyses providing insights into each sorption parameter's effect. Both numerical modeling and experimental measurements were employed to assess sand filter retention rates. The impact of flow rate on sorption reveals variations in distribution coefficient (Kd), mass transfer coefficient (β), and irreversible sorption rate (K1). Lower flow rates are correlated with higher Kd and β values, indicating an increase in sorption and diminished mass transfer rates. The findings revealed that an increase in Kd resulted in a more gradual sorption process with a decrease in peak concentration, whereas changes in β influenced the rate of sorption and peak concentration to a lesser extent compared to Kd. Lower K1 values are associated with higher peak concentrations and decreased retention efficiency. Retention rates were evaluated by a numerical model and found as 28 ± 1% at a flow rate of 31 ml min⁻¹ and 17 ± 1% at 65 ml min⁻¹. The introduction of MPls into soil environments has been noted to modify transport dynamics into soil. As a result, these alterations effects hydrological characteristics of soil, thereby impacting quality of groundwater and agricultural output. The mean absolute error (MAE) of 6% between modeled and observed retention rates suggests minor discrepancies. This study highlights the importance of examining retention efficiency and the accuracy of numerical models in porous media during MPl transport.

In this work, we propose simple and robust technique for the retrieval of underlying surface spectral albedo using spaceborne observations. It can be used to process both multispectral moderate resolution satellite data and also multi - zone high spatial resolution data. The technique can work automatically for different types of land surfaces without using huge databases accumulated in advance. The new cloud discrimination and retrieval of the water vapor content in atmosphere procedures are presented. The key point of the proposed atmospheric correction technique is the suggested single-wavelength method for determining the atmospheric aerosol optical thickness without reference to a specific type of underlying surface spectrum. The retrievals of spectral albedo for various land surfaces with developed technique, performed using computer simulation and experimental data, have demonstrated a high retrieval accuracy.

Bistatic radar experiments have been used to study surface characteristics of extra-terrestrial bodies in the Solar System, including the Moon, Venus, Mars, and Titan. This paper proposes a 3D model to characterize the scattered field of a Gaussian rough surface on an extra-terrestrial body for an orbital bistatic radar configuration. Specifically, this model will investigate how the variability of surface roughness impacts the spectral broadening of the received signal using physical optics approximations and ray tracing on a surface model using a facet approach with Gaussian properties. A linear relationship between spectral broadening of the signal and surface roughness was found. This relationship is in line with results obtained by commonly used analytical models for bistatic radar on planetary surfaces.

The valorization of the large amount of crude glycerol formed from biodiesel industry, is of primordial necessity. One possible direction with high interest to the biorefiniery sector is the production of fuel additives as solketal, though the acetalization of glycerol with acetone. This is a chemical process that conciliates high sustainability and economic interest, since solketal contributes to the fullfilment of a Circular Economy Model through its use in biodiesel blends. The key to guarantee high efficiency and high sustainability for solketal production is the use of a recovery and recyclable heterogeneous catalyst. Some examples are already reported in the literature (first example in 2012), and this review intends to conciliate the information spreaded in this topic and established the most important reacional parameters and the main catalytic characteristics strategies to achieve high solketal production in short reaction time.

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

Given a quasi-definite linear functional u in the linear space of polynomials with complex coefficients let us consider the corresponding sequence of monic orthogonal polynomials (SMOP in short) (Pn)n≥0. For the Christoffel transformation u˜=(x−c)u with SMOP (P˜n)n≥0, we are interested to study the relation between u˜ and u(1)˜, where u(1) is the linear functional for the associated orthogonal polynomials of the first kind (Pn(1))n≥0 and u(1)˜=(x−c)u(1) is its Christoffel transformation. This problem is also studied for the Geronimus transformations.

In this paper, the ratio of gross agricultural production (GAP) and agricultural carbon emission is defined as agricultural carbon emission efficiency (ACEE). Considering rural labor transfer (RLT) increases the agricultural machinery intensity (AMI), the two are substitutes for each other and may interact with agricultural carbon emission efficiency (ACEE), we constructed a Simultaneous Equations Model (SEM) of ACEE, RLT and AMI, and analyzed the interaction mechanism of these three variables by using the Three-Stage Least Squares (3SLS) method to solve the endogeneity of the model. The following conclusions are drawn. First, RLT and AMI significantly promote the improvement of ACEE, while the improvement of ACEE and AMI further promotes RLT. Secondly, the causal relationship and influence mechanism of ACEE, RLT and AMI are interactive and multi-directional. An increase in AMI promotes ACEE, but an increase in ACEE inhibits an increase in AMI, suggesting that the marginal rate of substitution of machinery for labor is decreasing. Finally, China has significant regional heterogeneity. Labor transfer and machinery are only direct factors in increasing ACEE, while factors such as economic base, technology level and farmers' attitudes provide environmental support for the effective improvement of ACEE.

This study analyzes the relevance of governance structure for efficiency in revenue collection by Brazilian Water Utilities (WUs). Data was collected from the National Information System on Sanitation (SNIS) for 127 Brazilian WUs, covering a balanced longitudinal panel from 2018 to 2022. Governance structures evaluated included Ownership (public or private) and Corporatization (publicly traded or not). In scientific databases, we did not find studies on the efficiency of specific WUs in collecting customer bills for services rendered and its relationships with this type of governance; thus, this would be the main innovative contribution of the study to the previous literature. In the first stage, the study utilized the Dynamic Slack Based Model (DSBM) to assess revenue collection efficiency. In the second stage, an econometric model with Generalized Estimating Equations (GEE) to explain the efficiency. The findings revealed a global average inefficiency of 50.47% in revenue collection. Corporatization was linked to higher collection efficiencies, while ownership type was significant, but with lower collection efficiency. Factors such as tariff accessibility, urbanization, and the COVID-19 pandemic also influenced efficiency. The study suggests regulatory bodies should consider these insights to implement policies that prevent inefficiencies from affecting the tariff system for services.

Purpose of publication: - Preparation of bibliometric data exported from the Scilit platform on energy efficiency and conservation for further analysis to identify relevant research topics. - To identify potential issues in the processing of data exported from the Scilit platform. - Providing colleagues with the opportunity to use the prepared data and examples of their analysis for independent research on topical issues of energy efficiency and energy conservation using materials provided by the Scilit platform. Research Materials: Files in CSV and RIS formats exported from Scilit for the query "energy conservation OR efficiency" in Common Fields [Title, Abstract, Keyword], using filters: Content Type → Journal Article; Year→2021-2023; Subject → Industrial Engineering (29.8K), Energy and Fuel Technology (9.8K), Manufacturing Engineering (9.2K). A total of 30K records sorted by their relevance (10K for each year) were exported. Data are current as of 14-03-2024. Methods: Preprocessing of title, annotation, and keyword field texts using lemmatization dictionaries collected on GitHub, removal of keywords taken from GATE and spaCy, and "manual" editing. Using VOSviewer to analyze publication topics by clustering keywords based on their co-occurrence. Using Scimago Graphica to build bubble diagrams.Application of the GSDMM algorithm for clustering bibliometric records by title and annotation texts. Creation of a dictionary for this algorithm using the keyword field.Use of the Carrot2 demo version and the NMF algorithm for a more detailed analysis of the topics of the record clusters obtained from GSDMM. Results: are presented in the form of initial and interim tables and graphs obtained in the course of this study. The full tables are provided as references to the attached materials. Supplementary material for this preprint on figshare: Chigarev, Boris (2024). Supplementary material for preprint "Analyzing the Possibilities of Using the Scilit Platform to Identify Current Energy Efficiency and Conservation Issues". figshare. Dataset. https://doi.org/10.6084/m9.figshare.25574058.v1

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

As a fast and nondestructive spectroscopic analysis technique, Raman spectroscopy has been widely applied in chemistry. However, noise is usually unavoidable in Raman spectra. Hence, denoising is an important step before Raman spectral analysis. A novel spectral denoising method based on variational mode decomposition (VMD) was introduced to solve the above problem. The spectrum is decomposed into a series of modes (uk) by VMD. Then, the high frequency noise modes are removed and the remaining modes are reconstructed to obtain the denoised spectrum. The proposed method was verified by two artificial noised signals and two actual Raman spectra. As comparison, empirical mode decomposition (EMD), Savitzky-Golay (SG) smoothing and discrete wavelet transformation (DWT) are also investigated. At the same time, signal-to-noise ratio (SNR) was introduced as evaluation indicators to verify the performance of the proposed method. The results show that compared with EMD, VMD can significantly improve mode mixing and endpoint effect. Some information of the small sharp peak is lost after VMD denoising. However, VMD lost fewer information than that of EMD, SG smoothing and DWT. Moreover, the Raman spectrum by VMD denoising is more excellent than that of EMD, SG smoothing and DWT in terms of visualization and SNR. Therefore, VMD provides superior denoising capabilities for Raman spectra.

Despite great technical capabilities, the theory of non-contact temperature measurement is usually not fully applicable to the use of measuring instruments in practice. While black body calibrations are in practice well established and easy to accomplish, this calibration protocol is never fully applicable to measurements of real objects under real conditions. Currently, the best approximation to real world radiation thermometry is grey body radiation thermometry, which is supported by most measuring instruments to date. Nevertheless, the metrological requirements necessitate traceability, therefore real body radiation thermometry is required for temperature measurements of real bodies. This article documents the current state of temperature calculation algorithms for radiation-thermometers and the creation of a traceable model for radiation thermometry of real bodies that uses a digital twin model of the system of measurement to compensate for the loss of data, caused by spectral integration, which occurs when thermal radiation is absorbed on the active surface of the sensor. To solve this problem, a hybrid model with variable scalar inputs is proposed, in which the scalar input parameters are calculated to correspond to the system of measurement. The method for calculating the effective parameters is proposed and verified with the theoretical model of non-contact thermometry. The sum of effective instrumental parameters is presented for different temperatures to show that the rule of radiation thermometry of grey bodies, according to which the sum of instrumental emissivity and instrumental reflectivity equals to 1, does not hold in radiation thermometry for real bodies. Using the derived models of radiation thermometry, the uncertainty of radiation thermometry due to the uncertainty of spectral emissivity is analysed by simulated measurements along the temperature ranges of various radiation thermometers, enabling traceable non-contact temperature measurements with known measurement uncertainty under any known conditions.

Stark widths for 23 transitions in Al IV have been calculated employing modified semiempirical method. The results are obtained for an electron density of 10^17 cm−3 and temperatures from 10,000 K up to 160,000 K. The results obtained in this investigation are used for the examination of the influence of Stark broadening in Al IV stellar spectra, as well as to check Stark width regular behavior and similarites within Al IV spectrum.

This paper presents a novel CNN-based architecture, referred to as Q-Net, to learn local feature descriptors that are useful for matching image patches from two different spectral bands. Given correctly matched and non-matching cross-spectral image pairs, a quadruplet network is trained to map input image patches to a common Euclidean space, regardless of the input spectral band. Our approach is inspired by the recent success of triplet networks in the visible spectrum, but adapted for cross-spectral scenarios, where for each matching pair there are always two possible non-matching patches; one for each spectrum. Experimental evaluations on a public cross-spectral VIS-NIR dataset shows that the proposed approach improves the state-of-the-art. Moreover, the proposed technique can also be used in mono-spectral settings, obtaining a similar performance to triplet network descriptors, but requiring less training data.

Effective oral care is important to maintain a high quality of life. Therefore, plaque control can prevent the development and recurrence of periodontitis. Brushing with a toothbrush and toothpaste is a common way to remove plaque; however, excessive brushing or brushing with abrasive toothpaste can cause wear and tear on the dental crown. Hence, we aimed to quantitatively compare the plaque-removal efficiency and tooth wear of toothbrushes using bioelectric effect (BE) with those of mechanical electric toothbrushes. To generate the BE signal, an electronic circuit was developed and embedded in a toothbrush. Further, typodonts were coated with cultured artificial plaques and placed in a brushing simulator. A toothpaste slurry was applied, and the typodonts were eluted with tap water after brushing. The plaques of the typodonts were captured, and the images were quantified. For the tooth wear experiment, polymethyl methacrylate disk resin blocks were brushed twice a day, and the thickness of the samples was measured. Subsequently, statistical differences between the experimental toothbrushes and typical toothbrushes were analyzed. The BE toothbrush had a higher plaque-removal efficiency and could minimize tooth wear. This study suggests that the application of BE may be a new solution for oral care.

Since its conception with the smallpox vaccination, worldwide-used vaccines have thwarted multiple pandemics including the recent COVID-19 outbreak. Insightful studies uncovered complexities of different functional networks of CD4 T cells [T helper 1 (Th1); Th2, Th17] and CD8 T cells (T cytotoxic; Tc) as well as B cells (BIgM, BIgG, BIgA and BIgE) subsets during response to vaccination. Both T and B cell subsets forge central, peripheral and tissue-resident subsets during vaccination. It also became apparent that each vaccination formed the network of T regulatory subsets, namely CD4+CD25+Foxp3+ T regulatory (Treg) cells and interleukin-10 (IL-10)-producing CD4+Foxp3− T regulatory 1 (Tr1) as well as many others, are shaping the quality/quantity of vaccine-specific IgM, IgG, and IgA antibody production. These components are especially critical for immunocompromised patients, such as older individuals and allograft recipients, as their vaccination may be ineffective or less effective. This review focuses on presenting how pre- and post-vaccination Treg/Tr1 levels influence the vaccination efficacy. Experimental and clinical work revealed that the Treg/Tr1 involvement evoked different immune mechanisms in diminishing vaccine-induced cellular/humoral responses. Alternative steps may be considered to improve the vaccination response by increasing a dose, changing the delivery route and/or repeated booster doses of vaccines. Vaccination may be combined with anti-CD25 (IL-2Ra chain) or anti-PD-1 (programmed cell death protein) monoclonal antibody (mAb) to decrease Tregs and boost the T/B cell immune response. All these data and strategies for immunizations are presented and discussed, aiming to improve the efficacy of vaccination in humans and especially in immunocompromised and older individuals as well as organ transplant patients.

The presented work offers a novel process scheme for valorizing historical Pb-Zn slag, which involves crushing, grinding, and then using separation techniques to concentrate valuable components (nonferrous metals). This methodology could have a significant impact on the global beneficiation of metallurgical slags since, in theory, it is significantly more simple, environmentally friendly, and cost-effective than standard pyrometallurgical or hydrometallurgical procedures. According to previous physicochemical and mineralogical studies, Pb-Zn slag from "Topilnica" Veles is a valuable secondary raw material. This inhomogeneous technogenic resource contains substantial amounts of nonferrous metals (Pb, Zn, Cu, and Ag). However, laboratory tests have indicated that the Pb-Zn slag contains a very uneven valuable metals amounts, ranging from several g/ton to several tens of g/ton. The main issue is that traditional metallurgical procedures for releasing beneficial elements are not commercially viable since the valuable elements are "trapped" within amorphous aluminosilicates or intergrowths of alloy grains and glassy phases. Gravity concentration (Wilfley 13 shaking table) and magnetic separation (Davis separator and disk separator) were used to obtain the final concentrate following comminution and grindability testing. The gravity concentration proved more effective. This streamlined approach of valorizing Pb-Zn slag can reduce the need for hazardous chemicals used in hydrometallurgical refinement operations, as well as the extremely high temperatures required for pyrometallurgical processing. This is the first investigation into the feasibility of this novel approach, which includes direct investigations of the Pb-Zn slag feed using these alternative technologies. After extracting the valuable metals, the amorphous aluminosilicate part of the Pb-Zn slag can be reapplied as an alternative raw material in the building sector, adding to the circularity of the suggested approach..

Hazelnut shells (HS), scientifically known as Corylus avellana L. shells, are a waste produced in companies that process nuts. The main objective of this study was to find an efficient way to maximize the chemical potential of HS by solubilizing the hemicelluloses, which could then be used to recover sugars and at the same time increase the lignin content of this material in order to produce adhesives or high strength foams. In order to optimize the pre-hydrolysis process, two different temperatures (160 and 170 C) and times varying from 15 to 180 min were tested. All the remaining solid materials were then liquefied by polyalcohols with acid catalysis. The chemical composition of hazelnut shells was determined before and after the pre-hydrolysis. All the process was monitored by FTIR-ATR by determining the spectra of solids and liquids after pre-hydrolisis and liquefactions steps. The highest solubilization of hazelnut shells was found for 170 C and 180 min, resulting in a 25.8% solubilization. Chemical analysis after the hydrolysis process showed a gradual increase in the solubilization of hemicelluloses as both the temperature and time of the reactor were increased. Simultaneously, the percentages of α-cellulose and lignin in the material also increased with rises in temperature and duration. FTIR-ATR allowed for the detection of significant spectral changes in the hazelnut shells from their initial state to the solid residue and further into the liquefied phase. This confirmed that pre-hydrolysis was effective in enhancing the chemical composition of the material, making it more suitable for the production of adhesives or polyurethane foams with enhanced mechanical strength.

Spectral image analysis has the potential to replace traditional approaches for assessing plant responses to different types of stress including herbicide, through non-destructive and high-throughput screening (HTS). Therefore, this study was conducted to develop a rapid bioassay method using a multi-well plate and spectral image analysis for diagnosis of herbicide activity and mode of action. Crabgrass (Digitaria ciliaris) as a model weed was cultivated in multi-well plates and subsequently treated with 6 herbicides with different modes of action when they reached the 1-leaf stage, using only a quarter of the recommended dose. To detect plant response to herbicides, plant spectral images were acquired after herbicide treatment using RGB, infrared (IR) thermal, and chlorophyll fluorescence (CF) sensors and analyzed for diagnosing herbicide efficacy and mode of action. Principal Component Analysis (PCA) using all spectral data successfully distinguished herbicides and clustered depending on their modes of action. The performed experiments have shown that the multi-well plate assay combined with spectral image analysis can be successfully applied for herbicide bioassay. In addition, the use of spectral image sensors, especially in CF image, would facilitate HTS by enabling rapid observation of herbicide response, as early as 3 hours after herbicide treatment.

Selecting drought-tolerant and more water-efficient wheat genotypes is a research priority, spe-cifically in regions with irregular rainfall or areas where climate change is expected to result in reduced water availability. The objective of this work was to use high-throughput measurements with morphophysiological traits to characterize wheat genotypes in relation to water stress. Field experiments were conducted from May to September 2018 and 2019, using a sprinkler bar irriga-tion system to control water availability to eighteen wheat genotypes: BRS 254; BRS 264; CPAC 01019; CPAC 01047; CPAC 07258; CPAC 08318; CPAC 9110; BRS 394 (irrigated biotypes) and Aliança; BR 18_Terena; BRS 404; MGS Brilhante; PF 020037; PF 020062; PF 120337; PF 100368; PF 080492; TBIO Sintonia (rainfed biotypes). The water regimes varied from 22 to 100% of the crop evapotranspiration replacement. Water stress negatively affected gas exchange, vegetation indices and grain yield. High throughput variables TCARI, NDVI, OSAVI, SAVI, PRI, NDRE and GNDVI had higher correlation with yield and morphophysiological measurements. The drought re-sistance index indicated that genotypes Aliança BRS 254, BRS 404, CPAC 01019, PF 020062, and PF 080492 were more drought tolerant.

It is strongly desirable to accurately detect the clouds in hyperspectral images onboard before compression. However, conventional onboard cloud detection methods are not appropriate to all situation such as shadowed cloud or darken snow covered surfaces which are not identified properly in the NDSI test. In this paper, we propose a new spectral–spatial classification strategy to enhance the orbiting cloud screen performances obtained on hyperspectral images by integrating threshold exponential spectral angle map (TESAM), adaptive Markov random field (aMRF) and dynamic stochastic resonance (DSR). TESAM is performed to classify the cloud pixels coarsely based on spectral information. Then aMRF is performed to do optimal process by using spatial information, which improved the classification performance significantly. Some misclassification points still exist after aMRF processing because of the noisy data in the onboard environment. DSR is used to eliminate misclassification points in binary labeling image after aMRF. Taking level 0.5 data from hyperion as dataset, the average overall accuracy of the proposed algorithm is 96.28% after test. The method can provide cloud mask for the on-going EO-1 images and related satellites with the same spectral settings without manual intervention. The experiment indicate that the proposed method reveals better performance than the classical onboard cloud detection or current state-of-the-art hyperspectral classification methods.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

In order to explore the yield-increasing mechanism of mechanized potato planting with corn straw mulching, a two-year ( 2021 and 2022 ) field experiment was conducted to study the effects of mechanized no-tillage with straw mulching on potato yield and water use efficiency. This experiment included corn straw mulching potato mechanized no-tillage planting ( JG ), plastic film mulching ( HM ) and open flat planting ( CK ). The results showed that mechanical no-tillage with straw mulching had significant effects on soil water content, yield and water use efficiency in 0-100 cm soil layer (p&lt; 0.05). There was no significant difference in yield between JG and HM, but it was significantly higher than that of CK. The yield of JG was 3.09 %~12.27 % higher than that of CK. The yield increase was mainly achieved by increasing the potato weight per plant ( 0.697 ~ 0.862** ) and the average single potato weight ( 0.048 ~ 0.631 ). The tuber weight per plant was positively correlated with the plant height at seedling stage ( 0.03 ~ 0.92** ), and positively correlated with the dry weight of stems and leaves at tuber expansion stage and starch accumulation stage ( 0.74** ~ 0.95**). It was negatively correlated with the number of branches at tuber formation stage ( -0.33 ~ -0.88** ). Compared with CK, JG could significantly improve the water use efficiency of potato and reduce the water consumption during the whole growth period of crops. In 2021, JG was 6.5 % higher than CK, and HM was 6.88 % lower than CK. In 2022, JG and HM increased water use efficiency by 26.17 % and 14.50 % compared with CK. It can be seen that JG is a green and efficient mechanized potato cultivation technology suitable for dry farming areas.

The object of study in the article is the auxiliary variable-frequency electric drive onboard of an AC electric locomotive, and more precisely, the structure and parameters of the control system of the active corrector of power factor (ACPF), which is part of the electric drive, as a unit that ensures electromagnetic compatibility of the electric drive with other equipment on board the electric locomotive and catenary and its energy efficiency. The topic of the article's research is the substantiation of the structure of the ACPF control system, the choice of types (transfer functions) of controllers and the calculation of their parameters. The research method chosen was the calculation of the transfer functions of the controllers of the cascaded loops control system, followed by computer simulation using the OrCAD software. The results of simulating a cascaded two loops control system of an ACPF with different types of controllers are presented and analytically compared. It is concluded that it is advisable to use a cascaded two loops control system, containing a voltage control loop and a current control loop. The best results show the simulation when using an aperiodic current controller (A-controller) and a proportional-integral voltage controller (PI-controller). The data obtained serve as the basis for further improvement of the operation of the ACPF by enhancing and optimizing the settings, structure and algorithms of the control system, which, with the selected hardware of power converter unit, will allow the ACPF to perform its functions with a high degree of reliability in an entire range of disturbing and control influences.

: Greenhouse plants are usually grown in containers filled with growing media. Peat is the main component of the growing media used in greenhouses. However, peat substrate is made from peat from drained peatlands, which is a limited resource. Wood fiber can be an alternative to use as a growing media for controlled-climate crops. The chemical properties of the growing media interact and change continuously due to the small volume of the growing media, which is limited by the vegetative container. Therefore, this study aims to gain new knowledge on the impact of nutrient changes in the microbial degradation of carbon compounds in wood fiber and mixtures with peat substrate on the content and uptake of nutrients required by plants. Cucumbers (Cucumis sativus L.) were cultivated in growing media of peat substrate and wood fiber: (1) peat substrate (PS); (2) wood fiber (WF); (3) wood fiber and peat substrate 50/50 v/v (WF/PS 50/50); (4) wood fiber and peat substrate 25/75 v/v (WF/PS 25/75). The rates of fertilization were the following: (1) conventional fertilization (CF); (2) N13; (3) N23; (4) N30. Fertilization of cucumbers with different rates of nitrogen influenced the nutrient uptake. Plants grown in WF/PS 50/50 and WF/PS 25/75 growing media had the best Cu uptake when fertilized with N23. When the plants grown in the wood fiber media and the 50/50 media were fertilized with N13, N23, and N30, the Mn content in the growing media at the end of the growing season was significantly lower than the Mn content in the media with conventional fertilization. Thus, nitrogen improved the uptake of Mn by plants grown not only in the wood fiber but also in combinations with peat substrate. Growing plants in wood fiber and fertilizing them with N13 can result in optimum uptake of micronutrients. The number and mass of cucumber fruits per plant were influenced by the amount of wood fiber in the growing media and the application of nitrogen fertilizer. The highest number of fruits and mass of fruits per plant was obtained significantly higher when cucumbers were grown on WF/PS 50/50 growing media with additional N13 fertilization.

Using pumps operating as turbines (PATs) offers the possibility of increasing the sustainability of water and energy systems by recovering the excess of energy that would be otherwise lost in pressure reducing valves or head loss chambers. In on-grid applications, there are many research works and implementations of PATs. However, there is still limited research for the optimization of efficiency and stability of PATs operating in off-grid systems. This work contributes to the development of stable direct current (DC) off-grid electric systems based on PATs, by optimizing and analysing the energy efficiency and stability for a wide range of operation. A self-excited induction generator (SEIG) coupled to the PAT is provided to cover the conventional type of electric ma-chines typically coupled to the hydraulic pumps. In this context, a methodology is proposed, based on the hydraulic, mechanical and electric subsystems, to define the PAT-SEIG operational area, to maximize energy conversion and the system efficiency. This will guarantee stable electric output quantities when operating in a DC off-grid system. In addition, an analytical model is proposed to estimate the PAT-SEIG operation under specific conditions. With this, water managers are suitable to design and optimize an off-grid PAT-SEIG system and to define the best hydraulic machines, electronic equipment, and all different control elements to maximize energy conversion within the target of operational limits. To develop and verify this new methodology, two micro PAT-SEIG setups were implemented in the hydraulic laboratory of IST/CERIS under typical operating conditions. The proposed solution proved to be resilient under a variable load regime. The system's maximum efficiency can be adapted using different capacitor values for the excitation of the SEIG, and the operational range is limited to the electric components. Considering the nominal efficiencies of the system’s components, the maximum p.u. efficiency obtained for each PAT-SEIG system were between 0.7 and 0.8 p.u.

Hyperspectral anomaly detection is to recognize anomalies from complex scene in an unsupervised way. Currently, many spectral-spatial detection methods have been proposed with a cascaded manner. However, they often neglect complementary characteristics between spectral and spatial dimensions, which easily leads to yield high false alarm rate. To alleviate this issue, a spectral-spatial information fusion (SSIF) method is designed for hyperspectral anomaly detection. First, an isolation forest is exploited to obtain spectral anomaly map, in which the object-level feature is constructed with entropy rate segmentation algorithm. Then, a local spatial saliency detection scheme is proposed to produce spatial anomaly result. Finally, the spectral and spatial anomaly scores are integrated together followed by a domain transform recursive filtering to generate the final detection result. Experiments on five hyperspectral datasets prove that the proposed SSIF produces superior detection result over other state-of-the-art detection techniques.

Spectral unmixing represents both an application per se and a pre-processing step for several applications involving data acquired by imaging spectrometers. However, there is still a lack of publicly available reference data sets suitable for the validation and comparison of different spectral unmixing methods. In this paper we introduce the DLR HyperSpectral Unmixing (DLR HySU) benchmark dataset, acquired over German Aerospace Center (DLR) premises in Oberpfaffenhofen. The dataset includes airborne hyperspectral and RGB imagery of targets of different materials and sizes, complemented by simultaneous ground-based reflectance measurements. The DLR HySU benchmark allows a separate assessment of all spectral unmixing main steps: dimensionality estimation, endmember extraction (with and without pure pixe assumption), and abundance estimation. Results obtained with traditional algorithms for each of these steps are reported. To the best of our knowledge, this is the first time that real imaging spectrometer data with accurately measured targets are made available for hyperspectral unmixing experiments. The DLR HySU benchmark dataset is openly available online and the community is welcome to use it for spectral unmixing and other applications.

In this study, we investigate spectral structure of conformable Sturm-Liouville problems and with this end, we obtain representation of solutions under different initial conditions and asymptotic formulas for eigenfunctions, eigenvalues, norming constants and normalized eigenfunctions. Consequently, we prove the existence of infinitely many eigenvalues. Also, we compare the solutions with graphics with different orders, different eigenvalues, different potentials and so, we observe the behaviors of eigenfunctions. We give an application to the α-orthogonality of eigenfunctions and reality of eigenvalues for conformable Sturm-Liouville problems defined by [15] in the last section.

This retrospective study aimed to evaluate the performance of the hormone treatment protocols, determine the factors associated with pregnancy success after hormone treatment, and compare the cost-efficiencies of two types of hormone treatment among cyclic and noncyclic anestrous dairy cows. The clinical records of 279 anestrous cows who received hormone treatment for artificial insemination (AI) from 64 herds in the western region of Thailand were obtained from Kasetsart University Veterinary Teaching Hospital from January to August 2017. The performance of the hormone treatment protocols, fixed-time AI (TAI) and estrus detection before AI (EAI), showed that the pregnancy risk for the TAI protocol was higher than for the EAI protocol, but pregnancy per AI did not differ significantly between the two protocols in cyclic and noncyclic cows. Multivariate logistic regression analysis showed that cows receiving the TAI protocol were more likely to be pregnant compared to those treated with the EAI protocol. Cows with a 3.00 body condition score (BCS) &lt;3.75 after treatment and loose-housing cows were more likely to become pregnant. Treatment during winter showed higher pregnancy success than in the summer and rainy seasons. The cost-efficiency analysis showed that the TAI protocol was the most cost-efficient option for noncyclic cows, whereas the EAI protocol was the most cost-efficient option for cyclic cows.

Electrochromic measurements have been performed throughout the full composition range of reactive magnetron-sputtered mixed Titanium oxide and Molybdenum oxide (TiO2-MoO3) to search for enhanced Coloration Efficiency (CE). Optical parameters and composition have been determined and mapped by using Spectroscopic Ellipsometry (SE). Scanning Electron Microscopy (SEM) with Energy-Dispersive X-ray Spectroscopy (EDS). EDS has been used to check the SE results as it was used in our earlier paper [N. T. Ismaeel et al, Materials 2023, 16(12), 4204] for (TiO2-SnO2). Ti and Mo targets were put separately from each other, and the Indium-Tin-Oxide (ITO) covered glass and Si-probes on a glass substrate (30 cm × 30 cm) were moved under the two separated targets (Ti and Mo) in a reactive Argon-Oxygen (Ar-O2) gas mixture. By using this combinatorial process, all the compositions (from 0 to 100%) were achieved in the same sputtering chamber after one sputtering process. The CE (the change of light transmission for the unit electric charge) of mixed metal oxides (TiO2-MoO3) that are deposited by reactive sputtering has been studied in an electrochemical cell. This paper aims to assess the results of investigations of such materials showing the enhanced electrochromic behavior compared to the pure materials and to enhance the Coloration Efficiency.

Non-destructive, accurate, and timely approach for crop yield prediction at field scale is vital for precision agriculture. This study aimed to investigate the appropriate wavelengths and their combinations to explore the new SIs derived from UAV hyperspectral images in predicting yield during the growing season of spring maize. The best wavelengths and new SIs, including the difference spectral index, ratio spectral index, and normalized difference spectral index forms, were obtained by the contour maps constructed by the coefficient of determination (R2) from the linear regression models between the yield and all possible SIs screening out from the 450-950 nm wavelengths. The results showed that the most sensitive wavelengths were 640-714 nm at WJQ, 450-650 nm and 750-950 nm at SKS, and 450-700 nm and 750-950 nm at FJJ. The new SIs established here were different across the three experimental fields, and their performance on maize yield prediction were generally better than that of the published SIs. In addition, the new SIs presented different response to various N fertilization levels. This study demonstrated the potential of exploring new spectral characteristics from remote sensing technology for predicting field-scale crop yield in spring maize cropping systems before harvest.

The knowledge of the optical properties of biological tissues in a wide spectral range is highly important for the development of noninvasive diagnostic or treatment procedures. The absorption coefficient is one of those properties, from which various information about tissue components can be retrieved. Using transmittance and reflectance spectral measurements acquired from ex vivo rabbit brain cortex samples, allowed to calculate its optical properties in the ultraviolet to the near infrared spectral range. Melanin and lipofuscin, the two pigments that are related to the ageing of tissues and cells were identified in the cortex absorption. By subtracting the absorption of these pigments from the absorption of the brain cortex, it was possible to evaluate the true ratios for the DNA/RNA and hemoglobin bands in the cortex – 12.33 fold (at 260 nm), 12.02 fold (at 411 nm) and 4.47 fold (at 555 nm). Due to the fact that the accumulation of melanin and lipofuscin increases with the ageing of the brain tissues and are related to the degeneration of neurons and their death, further studies should be performed to evaluate the evolution of pigment accumulation in the brain to prevent the development of Alzheimer, Parkinson and stroke pathologies in the brain.

As prominent oil producers, the Gulf Cooperation Council (GCC) countries have played a significant role in the global energy market. However, as the world's attention increasingly shifts towards environmental sustainability, understanding the implications of the GCC's economic activities on CO2 emissions becomes indispensable. This research paper investigates the relationship between specific economic indicators and their impact on CO2 emissions in the GCC from 2001 to 2021. The study employs quantile regression, a powerful statistical method that estimates the conditional quantiles of a response variable given a set of predictor variables. The findings reveal several important insights: Financial institution efficiency is significant and negative at a 1% level at the lower (10th) -83537.3 and the higher quantile (90th) -549002.3. The relationship between GDP per capita and CO2 emissions varies across quantiles, highlighting the complexity of the growth-environment nexus. Total patents exhibit a positive and significant relationship with emissions, underscoring the importance of directing innovation towards environmentally sustainable solutions. Renewable energy consumption displays a nuanced relationship with CO2 emissions, with a stronger negative impact observed at higher consumption levels. This underscores the potential of renewable energy to mitigate emissions when integrated at scale. The study's outcomes hold crucial policy implications for the GCC countries as they seek to align economic growth with environmental sustainability. The findings emphasize the importance of fostering financial institution efficiency, promoting green innovation, and expanding renewable energy sources to reduce emissions

Photothermal therapy (PTT) can overcome cancer treatment resistance by enhancing cell membrane permeability, facilitating drug accumulation, and promoting drug release within the tumor tissue. Iron oxide nanoparticles (IONPs) have emerged as effective agents for PTT due to their unique properties and biocompatibility. Approved for the treatment of anemia, as MRI contrast agents, and as magnetic hyperthermia mediators, IONPs also offer excellent light-to-heat conversion and can be manipulated using external magnetic field for targeted accumulation in specific tissues. Optimizing parameters such as laser wavelength, power density, shape, size, iron oxidation state, functionalization, and concentration is crucial for IONPs effectiveness. In addition to PTT, IONPs enhance other cancer treatment modalities. They improve tumor oxygenation enhancing the efficacy of radiotherapy and photodynamic therapy. IONPs can also trigger ferroptosis, a programmed cell death pathway mediated by iron-dependent lipid peroxidation. Their magneto-mechanical effect can exert mechanical force on cancer cells to destroy tumors, minimizing damage to healthy tissues. This review outlines strategies for managing photothermal performance and PTT efficiency with iron oxide nanoparticles, as well as synergies with other cancer therapies.

In this study, a novel and efficient method was developed for the extraction of total flavonoids from Flos Sophorae Immaturus (FSI) using ultrasound-assisted deep eutectic solvent (UAE-DES). Different DES formulations were first investigated and choline chloride/1,2-propanediol (ChCl/PD) was identified as the optimal solvent due to its highest flavonoid yield. The extraction process was optimized through single factor experiments and response surface methodology (RSM). An extraction temperature of 68 °C, a sonication time of 41 minutes, a water content of 21% and a liquid-solid ratio of 21 mL/g were identified as the optimal conditions. Under these conditions, a maximum flavonoid yield of 378.77 mg RE/g DW was achieved. The crude extract was further purified using a macroporous D-101 resin, resulting in a flavonoid extract with a purity of 83.11 ± 3.54%. The antioxidant activity of the purified extract (FSPE) was evaluated using DPPH and ABTS radical scavenging assays, showing significant antioxidant properties with IC50 values of 52.50 μg/mL and 49.47 μg/mL, respectively. The UAE-DES method developed in this study not only significantly improves the extraction yield of flavonoids from FSI, but is also in line with sustainable and environmentally friendly practices. This method offers an environmentally friendly, efficient and scalable approach for the extraction of bioactive compounds from medicinal plants and has potential applications in the food, pharmaceutical and dietary supplement industries.

Balancing the efficiency and robustness of food systems is a well-known trade-off process. Over-optimization of efficiency may lead to excessive use of resources. On the other hand, under-optimization of efficiency may lead to excessive waste of resources. Using non-parametric methods can help in developing actionable frameworks through which decision-makers and stakeholders can effectively balance and improve food systems' efficiency and robustness. Under this context, this paper presents a new structured approach integrating two well-suited non-parametric methods for analyzing and balancing the interconnection between the efficiency and robustness of food systems. This approach consists of three main steps. First, the slacks-based data envelopment analysis (SBM-DEA) is utilized to analyze the efficiency of five food robustness dimensions. Second, the weighted efficiency of these dimensions is computed and analyzed to provide an insight into their influence on the food system efficiency. Finally, two search methods were developed to identify opportunities for improving efficiency and robustness. The outcomes of these methods have been analyzed and validated to ensure their effectiveness and viability. The operational and mathematical properties of the proposed approach were evaluated using data from thirty-seven food-producing countries. The weights of the robustness dimensions in this study were determined using the analytic hierarchy process (AHP) method. The input matrix of the AHP was constructed using expert judgment and consultations with stakeholders. The results of this study have shown an appropriate level of applicability and effectiveness of the proposed approach. While the first search method provided valuable insights, the second method proved to be more effective in identifying the sources of inefficacy of robustness dimensions. Several conclusions have been drawn and reported with some recommendations for future research works.

Energy consumption modelling is of critical importance for improving energy efficiency in the drive towards sustainable manufacturing. Modern manufacturing processes and machine tools are very complex as they involve interplay of several advanced technologies. Therefore, energy modelling of modern machine tools is a complex multi-disciplinary task. This paper proposes a systematic and practical framework to choose the appropriate modelling approach for a given industrial problem. The framework was validated by applying it to diverse industrial scenarios.

Data on Stark broadening parameters, spectral line widths and shifts, for 15 multiplets of N VI, which spectral lines are broadened by collisions with electrons, protons, alpha particles (He III) and B III, B IV, B V and B VI ions, are presented. They have been calculated, using the semiclassical perturbation theory, for temperatures from 50,000 K to 2,000,000 K, and perturber densities from 1016 cm−3 up to 1024 cm−3. These data are particularly of interest for the analysis and modelling of atmospheres of hot and dense stars, as e.g. white dwarfs, and for investigation of their spectra, but also for analyis ad modelling of laser driven plasma in proton-boron fusion research.

Spectral calibration consists of the calibration of wavelengths and the measurement of the instrument's spectral response function (SRF). Unlike conventional slits, the absorbed aerosol sensors (AAS) are used as a slit homogenizer, in which the spectral response function (SRF) is not a conventional Gaussian curve. To be more precise, the SRF is the convolution of the slit function of the spectrometer, the line spread function of the optical system, and the detector response function. The SRF of the slit homogenizer is a flat-topped multi-Gaussian function. Considering the convenience of fitting, a super-Gaussian function, which looks like a similar distribution to the flat-topped multi-Gaussian function, is used to fit the measured data in a spectral calibration. According to the results, the SRF’s shapes, due to the Earth port, resemble a Gaussian curve with a flatted top could be concluded, which contains an FWHM of 1.78–1.82 nm for the AAS. The results show that the correlation coefficients are about 0.99, which proves that the fitting function could better characterize the SRF of the instrument.

We propose a method for the estimation of the spectral response of a photodetector, using only the variation of the temperature of a black body source without the need of an expensive monochromator or a circular filter. The proposed method is suitable especially for infrared detectors in which the cut – off wavelength and the responsivity vs. wavelength is not exactly known. The method provides a rough estimation of the curve S(l) solving a Fredholm integral equation of the first kind. The precision of this technique depends on the number of temperatures at which the detector output is measured. Some example is given in order to better explain the proposed technique.

Multi-task Gaussian processes (MTGPs) are a powerful approach for modeling structured dependencies among multiple tasks. Researchers on MTGPs have contributed to enhance this approach in various ways. Current MTGP methods, however, cannot model nonlinear task correlations in a general way. In this paper we address this problem. We focus on spectral mixture (SM) based kernels and propose an enhancement of this type of kernels, called multi-task generalized convolution spectral mixture (MT-GCSM) kernel. The MT-GCSM kernel can model nonlinear task correlations and mixtures dependency, including time and phase delay, not only between different tasks but also within a task at the spectral mixture level. Each task in MT-GCSM has its own generalized convolution spectral mixture kernel (GCSM) with a different number of convolution structures and all spectral mixtures from different tasks are dependent. Furthermore, the proposed kernel uses inner and outer full cross convolution between base spectral mixtures, so that the base spectral mixtures in the tasks are not necessarily aligned. Extensive experiments on synthetic and real-life datasets illustrate the difference between MT-GCSM and other kernels as well as the practical effectiveness of MT-GCSM.

The Absorbing/scattering nature of aerosols affects the total radiative forcing and this absorption to total extinction ratio is quantified by single scattering albedo (SSA). Effect of SSA in the Ultraviolet (UV) irradiance is less studied and limited measurements are available. SSA retrieved at Athens, Greece during 2009-2014 from Ultraviolet Multifilter Radiometer (UVMFR) at 332 and 368 nm, were used to calculate incoming UV irradiance, alongside with ones from AERONET at visible wavelengths, from OMI satellite at 342.5 nm and from AEROCOM climatological database at 300 nm. UVA and UVB irradiances were estimated using a Radiative Transfer Model and we found that relative differences could be as high as 20%, while average relative differences varied from 2% to 8.7 % for the whole experimental period. Both UVA and UVB drop by a rate of ~12% for 0.05 aerosol absorption optical depth compared to ones estimated using SSA at visible range. Brewer irradiance measurements at 324nm were used to validate simulated irradiances and a better agreement was found when UVMFR SSAs were used with an average difference of 0.86%, while when using visible or climatological input, relative differences were estimated +4.91 and +4.15% accordingly.

Water pollution, intensified by the release of hard-to-degrade pollutants, poses severe threats to ecosystems, human health, and economic development. The existing advanced oxidation processes often involve high operational costs and may result in secondary pollution, highlighting the necessity for innovative and more sustainable solutions. To address these challenges, our study introduces a cost-effective and eco-friendly corona discharge barrier plasma discharger for wastewater treatment. Through the central composite design/response surface methodology, a high decolorization rate of 98% of methylene blue (MB) within 10 minutes was achieved by optimizing parameters such as pH and voltage. Furthermore, the mechanisms of the generation of reactive oxygen species via this device was discussed in detail and the degradation pathways of MB were described. Moreover, this device is also very energy-efficient, with a low energy density and electrical energy per order of 0.15 watt/mL and 5.79 kWh/m³/order, respectively. In conclusion, the plasma discharger developed in this study provides a cost-effective and environmentally sustainable solution for dye wastewater treatment. This research contributes significantly to the advancement of sustainable dye wastewater management practices, offering an innovative method that meets both environmental and economic objectives.

Despite advances in conservation-restoration treatments, most surface cleaning tests are subjectively evaluated. Scores according to qualitative criteria are employed to assess results, but these can vary by user and context. This paper presents a range of cleaning efficacy and homogeneity evaluation metrics for appraising cleaning trials, which minimise user bias by measuring quantifiable changes in the appearance and characteristic spectral properties of surfaces. The metrics are based on various imaging techniques (optical imaging by photography using visible light (VIS); spectral imaging in the visible-to-near-infrared (VNIR) and shortwave infrared (SWIR) ranges; chemical imaging by Fourier transform infrared (FTIR) spectral mapping in the mid-infrared (MIR) range; and scanning electron microscopy coupled with energy dispersive X-ray spectroscopy (SEM-EDX) element mapping). They are complemented by appearance measurements (glossimetry and colorimetry). As a case study showcasing the low-cost to high-end metrics, agar gel spray cleaning tests on exposed ground and unvarnished oil paint mock-ups are reported. The evaluation metrics indicated that spraying agar (prepared with citric acid in ammonium hydroxide) at a surface-tailored pH was a safe candidate for efficacious and homogenous soiling removal on water-sensitive oil paint and protein-bound ground. Further research is required to identify a gel-based cleaning system for oil-bound grounds.

Microwave transversal filters, which are implemented based on the transversal filter structure in digital signal processing, offer a high reconfigurability for achieving a variety of signal processing functions without changing hardware. When implemented using microwave photonic (MWP) technologies, also known as MWP transversal filters, they provide competitive advantages over their electrical counterparts, such as low loss, large operation bandwidth, and strong immunity to electromagnetic interference. Recent advances in high-performance optical microcombs provide compact and powerful multi-wavelength sources for MWP transversal filters that require a larger number of wavelength channels to achieve high performance, allowing for the demonstration of a diverse range of filter functions with improved performance and new features. Here, we present a comprehensive performance analysis for microcomb-based MWP spectral filters based on the transversal filter approach. First, we investigate the theoretical limitations in the filter spectral response induced by finite tap numbers. Next, we analyze the distortions in the filter spectral response resulting from experimental error sources. Finally, we assess the influence of input signal’s bandwidth on the filtering errors. These results provide a valuable guide for the design and optimization of microcomb-based MWP transversal filters for a variety of applications.

A quantum time-dependent spectrum analysis, or simply, quantum spectral analysis (QSA) is presented in this work, and it’s based on Schrödinger’s equation. In the classical world, it is named frequency in time (FIT), which is used here as a complement of the traditional frequency-dependent spectral analysis based on Fourier theory. Besides, FIT is a metric which assesses the impact of the flanks of a signal on its frequency spectrum - not taken into account by Fourier theory and let alone in real time. Even more, and unlike all derived tools from Fourier Theory (i.e., continuous, discrete, fast, short-time, fractional and quantum Fourier Transform, as well as, Gabor) FIT has the following advantages, among others: a) compact support with excellent energy output treatment, b) low computational cost, O(N) for signals and O(N2) for images, c) it does not have phase uncertainties (i.e., indeterminate phase for a magnitude = 0) as in the case of Discrete and Fast Fourier Transform (DFT, FFT, respectively). Finally, we can apply QSA to a quantum signal, that is, to a qubit stream in order to analyze it spectrally.

Black soldier fly larvae (BSFL) can use food by-products or residues as a growth substrate, and their use is considered a strategic solution to improve the sustainability and efficiency of animal production. BSFL need to be reared under controlled environmental conditions, as temperature can affect the welfare of the larvae and the efficiency of their bioconversion. The goal of this experiment was to test different diets: control, vegetable, carnivorous, omnivorous and to assess their effect on larval growth performance, chemical composition, and substrate temperature. BSFL (6-days-old) were randomly selected and allocated to one of the four diets for the entire experiment (8 days). The temperature in each container was measured twice daily using a thermal imaging camera. The vegetable diet led to significantly lower growth performance (p

In this work, we report the electric energy storage properties of (1-x)Bi0.5(Na0.8K0.2)0.5TiO3-xBi0.2Sr0.7TiO3 (BNKT-BST; x = 0.15-0.50) relaxor ferroelectric ceramics enhanced via a domain engineering method. A rhombohedral–tetragonal phase, the formation of highly dynamic PNRs, and a dense microstructure are confirmed from XRD, Raman vibrational spectra, and microscopic investigations. The relative dielectric permittivity (2664 at 1 kHz) and loss factor (0.058) were gradually improved with BST (x=0.45). The incorporation of BST into BNKT can disturb the long-range ferroelectric order, lowering the dielectric maximum temperature Tm and inducing the formation of highly dynamic polar nano-regions. In addition, the Tm shifts toward high temperature with frequency and a diffuse phase transition, indicating relaxor ferroelectric characteristics of BNKT-BST ceramics, which is confirmed by the modified Curie Weiss law (γ=1.83). The rhombohedral–tetragonal phase, fine grain size, and lowered Tm with relaxor properties synergistically contribute to a high recoverable energy density Wrec of 0.81 J/cm3 and a high energy efficiency η of 86.95% at 90 kV/cm for x = 0.45.

With the existence of several programming languages such as C/C++, Java, C#, LISP, Prolog, Python, Simula, F#, Go, Haskell, Scala, Ruby, Dart, Swift, Groovy etc. and diverse paradigms like structured, object-oriented, list, aspect-oriented, service-oriented, web, mobile and logic programming, there is a need to perform an exhaustive comparative analysis of diverse compilers and environments before making a choice of implementation technology in software engineering. Optimization of compilers helps to reduce execution time by making use of high speed processor registers, thereby, eliminating redundant computation. This paper reports some series of performance analysis done with some popular programming languages including Java, C++, Python and PHP. Programs involving recursive and iterative functions like factorial of large numbers and binary search of large arrays were run on the various platforms with the execution time recorded in milliseconds and represented in a chart. This can aid in making a selection of the appropriate language to use for a given application domain.