The aim of this work is to propose two different and complementary sensors for the structural health monitoring of concrete beams. In particular, a diffused sensing element and a split ring resonator network are presented. The first sensor is able to detect the variation of the dielectric properties of the concrete along the whole beam length, for a diffuse monitoring both during the important concrete curing phase and also for the entire life cycle of the concrete beams. The resonators instead work punctually, in their surroundings, allowing an accurate evaluation of the permittivity both during the drying phase and after. This allows the continuous monitoring of any presence of water both inside the concrete beam and in points that can be critical, in the case of beams in dams, bridges or in any case subject to a strong presence of water which could lead to deterioration, or worse, cause serious accidents. Moreover, the punctual sensors are able to detect the presence of cracks in the structure and to localize them.

Marine renewable energy is emerging as one of the fast-growing industry in the last decades, as modern society pushes for technologies that can convert energy contained from winds, waves, tides and stream flows. The implementation of renewable energy technologies impose high demands on both structural and environmental engineering, as the energy converters have to work under extreme conditions where parameters such as sea-bottom configuration, water transparency and depth, sea-states and prevailing winds are harsh. Constant monitoring of the marine environment is crucial in order to keep this sector reliable. Active acoustics is becoming a standard tool to collect multi-dimensional data from physical, geological and biological properties of the marine environment. The Div. of Electricity of Uppsala University have been developing an environmental monitoring platform based on sonar (Sound Navigation And Raging) systems. This platform aims to monitor the installation, operation and decommissioning of marine renewable energy converters. The focus will be given the observations of behaviours of marine animals in vicinity of energy converters but also structural inspection and monitoring of MRETs. This paper describes how this multifunctional environmental monitoring platform come to existence from the design to the deployment phase.

Giant unilamellar vesicles (GUVs) are membrane model used to study membrane properties. Electroformation is one of the methods used to produce GUVs. During electroformation protocol dry lipid film is formed. Drying of the lipid film induce Cholesterol (Chol) demixing artifact, in which Chol forms anhydrous crystals, where these crystals does not participate in formation of vesicles. This leads to a lower Chol concentration in the vesicle bilayers compared to the Chol concentration in the initial lipid solution. To address this problem, we propose novel electroformation protocol that includes rapid solvent exchange, plasma cleaning and spin-coating methods to produce GUVs. We tested the protocol focusing on vesicles with high Chol content using different spin-coating durations and vesicle types deposition. Additionally, we compared the novel protocol using completely dry lipid film. The optimal spin-coating duration for vesicles made out of phosphatidylcholine/Chol mixture was 30 s. Mulitlamellar vesicles (MLVs), large unilamellar vesicles (LUVs) obtained by extrusion of MLVs through 100 nm membrane pores and LUVs obtained by extrusion of previously obtained LUVs through 50 nm membrane pores were deposited on electrode for 1.5/1 Chol/phosphatidylcholine lipid mixture and the results were compared. Electroformation using all three deposited vesicle types gave a high GUVs yield, but deposition of LUVs obtained by extrusion of MLVs through 100 nm membrane pores gave the most reproducible results. Using deposition of these LUVs, we produced GUVs with high yield for 6 different Chol concentrations (from 0 % to 71.4%). Using protocol that includes dry lipid film GUVs yield was lower and Chol demixing artifact was induced, proving that the lipid film should never undergo drying when Chol content is high.

Background: Helicobacter pylori (H. pylori) is a prevalent bacterial pathogen implicated in various gastroduodenal diseases, including chronic gastritis, peptic ulcer disease, and gastric cancer. The COVID-19 pandemic has significantly influenced antibiotic prescription practices, potentially exacerbating antibiotic resistance in H. pylori. Objective: This study aims to investigate antibiotic prescription during COVID-19 pandemic in Croatia and its possible impact on H. pylori antibiotic resistance, with a focus on Croatia. Methods: A comprehensive literature search was conducted to identify relevant studies from March 2020 to June 2024. The search strategy included terms related to COVID-19, antibiotic prescription, and Croatia. Studies were selected based on predefined eligibility criteria, focusing on observational research addressing antibiotic use during the pandemic. Results: The COVID-19 pandemic leads to significant fluctuations in community antibiotic consumption within the European Union/European Economic Area. In Croatia, antibiotic use in 2022 surpassed 2019 levels, driven by increased consumption of macrolides and other antibiotics. This surge, influenced by early pandemic treatment claims and penicillin shortages, contributed to rising antibiotic resistance in H. pylori. Resistance rates to clarithromycin and levofloxacin were notably high, driven by mutations in the 23S rRNA, gyrA, and gyrB genes. Discussion: The increased antibiotic use during the COVID-19 pandemic has highly likely complicated H. pylori eradication efforts, highlighting the necessity of judicious antibiotic use and robust antimicrobial stewardship. The pandemic underscored the need for new therapeutic strategies, optimized eradication regimens, and advanced diagnostic methods to manage bacterial infections effectively. Conclusions: The COVID-19 pandemic has significantly impacted antibiotic use and resistance patterns, posing new challenges for H. pylori eradication. Addressing these challenges requires a multifaceted approach, including the development of new drugs and advanced diagnostics, coupled with sustained efforts in antimicrobial stewardship to combat emerging resistance threats.

Here we report a comparative study of the pyhtochemical profile and a biological activity of the two onion extracts, namely A. cepa L. and A. × cornutum (Clementi ex Visiani 1842). Identification of flavonoids and anthocyanins and their individual quantities were determined by high performance liquid chromatography (HPLC). The potency of both extracts to scavenge free radicals was determined by DPPH (2,2'-diphenyl-1-picrylhydrazyl) radical-scavenging activity and oxygen radical absorbance capacity (ORAC) methods. DNA protective role was further tested by single-cell gel electrophoresis (COMET) assay and by Fenton’s reagent causing double strand brakes on pUC19 plasmid. In the presence of both extracts, a significant decrease in the DNA damage was observed, which indicates a protective role of A. cepa and A. × cornutum on the DNA strand brakes. Additionally, cytotoxicity was tested on glioblastoma and breast cancer cell lines. The results showed that both extracts had antiproliferative effect, but the most prominent decrease in cellular growth was observed with glioblastoma cells

Ovarian cancer is among the most common causes of female mortality. Despite improvements in diagnostic methods, non-specific symptoms and delayed gynecological exams can lead to late-stage ovarian tumor discovery. In this study, the effect of an anti-cancer compound, 3-amino-N-(3-chloro-2-methylphenyl)-5-oxo-5,6,7,8-tetrahydrothieno[2,3-b]quinoline-2-carboxamide (Compound 1) was examined. Cytotoxicity, apoptosis, and metabolomic changes in ovarian cancer cell lines SK-OV-3 and OVCAR-3, as well as glycosphingolipid (GSL) expression, both on cancer stem cells (CSCs), marked as CD49f+ and non-CSCs (CD49f-) were explored. Treatment with Compound 1 reduced the percentage of CSCs compared to non-treated cells (P < 0.001). The expression of eight GSLs on CSCs and non-CSCs was examined using flow cytometry. Both cell lines showed a change in the glycophenotype of the cells, either up or down of its expression, after the treatment. These findings raise the possibility of specifically targeting CSCs in ovarian cancer therapy. Additionally, treatment of Compound 1 resulted in a statistically significant increase in both early and late apoptosis (P<0.001) suggesting a pivotal role in initiating programmed cell death by the apoptotic pathway. The metabolic analysis revealed that the treated cancer cells showed reduced metabolic activity compared to the control group (P < 0.001)

As marine traffic is contributing to pollution and mostly have predictable route with repetitive load profiles, to reduce their impact on environment, hybrid system with proton exchange membrane fuel cells (PEMFC-s) and battery pack, is promising replacement. For this purpose, the numerical model of repowered existing vessel that have two diesel engines with 300 kWe is developed. The goal of this paper is to develop numerical model which analyzes and determine equivalent hybrid ship propulsion system for known traveling route. The developed numerical model consists of an interconnected system with PEMFC stack and battery pack as power sources. Numerical model is developed and optimized to meet minimal required power demand for successful route demand, which has variable loads and daily sails six-time same voyage- in total 54 nautical miles. The results have shown that equivalent hybrid power system consists of 300 kWe PEMFC stack and battery pack with 424 kWh battery and state of charge varying between 20 and 87%. To power this new hybrid power system, hydrogen tank of 7200 l holding 284.7 kg at pressure of 700 bar is needed, compared to previous system that spend 1524 kg of diesel and generate 4886 kg of CO2.

This study investigates the mean annual water temperature trends at the confluence of the Sava and Danube Rivers, along with air temperature trends at the Belgrade meteorological station, spanning from 1956 to 2020. Results reveal a consistent increase in temperature across all three measuring stations, with the Danube experiencing a rise of 0.34°C/10 years, the Sava at 0.44°C/10 years, and Belgrade's air temperature increasing by 0.39°C/10 years. Employing the RAPS method, sharp rises in water temperature were pinpointed in 1989 for the Sava and 1990 for the Danube, while Belgrade's air temperature surge began in 1998. The highest intensity of air temperature increase within the recent period (1998-2020) was observed at the Belgrade observatory, reaching 0.76°C/10 years. Notably, the Sava exhibited a faster increase in water temperature over the last thirty years compared to the Danube. August marked the peak average water temperature for both rivers, while July recorded the highest average air temperature in Belgrade. Despite differing flow rates, both rivers exhibit similar hydrological regimes, with maximum flows occurring in April and minimum flows in August for the Sava, and October for the Danube. Seasonal temperature increases were most pronounced in summer, notably in August, with the smallest rises occurring during cold periods. Additionally, an inverse proportional relationship between mean annual water temperatures and discharges was observed at both river stations.

This study investigates the influence of adding hydrogen as an additive to gasoline in a four-stroke engine, utilizing a comprehensive thermodynamic comparative analysis conducted with self-developed engine model. The research aims to assess the performance, emissions, and efficiency of the engine when using gasoline-hydrogen blends, and to provide insights into the potential benefits of this approach. First the engine performance and emissions under different hydrogen blending levels were examined. A range of different air-to-fuel ratios (rich to lean) and varying percentages of hydrogen were considered. This systematic variation allowed for a detailed evaluation of the influence of hydrogen content on combustion efficiency, power out-put, and emissions characteristics. The analysis results included key parameters such as indicated specific fuel consumption and mean effective pressure. Additionally, the study focused on range prediction of nitrogen oxides (NOx) emissions, which are a critical environmental concern asso-ciated with internal combustion engines. The analysis of pressure and temperature profiles throughout the engine cycle shed light on the combustion characteristics and efficiency im-provements associated with hydrogen addition. In terms of emissions, the study projected that all emissions were reduced except NOx, which is highly dependent on hydrogen percentage, and it might be reduced in some cases, but with higher temperatures and pressures associated with hydrogen addition in most cases there is actually NOx increase, especially at higher engine loads.

Obstructive sleep apnea (OSA) often goes unrecognized despite common symptoms such as excessive daytime sleepiness, fatigue, and impaired quality of life (QoL). CPAP is the gold standard treatment for OSA, but optimal daily usage and time needed for observable effects remain unclear. This study aimed to investigate the short-term effects of CPAP on daytime sleepiness and QoL in patients with severe OSA. Medical records were collected from 87 patients with severe OSA who initiated CPAP therapy. Also, validated questionnaires were used before and after one month of CPAP to analyze QoL - the Calgary Sleep Apnea Quality of Life Index (SAQLI), the Cues to CPAP Use Questionnaire (CCUQ), and daytime sleepiness - the Epworth Sleepiness Scale (ESS). Multiple regression analysis was conducted to identify predictors of CPAP usage. Of the total participants aged 55.6±12.5, 77% were males, and 62% were CPAP adherent. Reductions in daytime sleepiness (ESS) were noted, as well as improvements in both overall QoL (SAQLI) and specifically in the domains of daily functioning, social interactions, emotional well-being, and symptom perception. Important cues for CPAP usage recognized by patients were physicians’ instructions and physicians’ worry regarding patients' condition. Furthermore, multiple regression revealed higher SAQLI scores and lower ESS scores as positive predictors of CPAP usage, along with lower AHI after one month of CPAP being associated with sufficient adherence.

Due to growing environmental concerns and stringent emissions regulations, optimizing the fuel consumption of marine propulsion systems is crucial. This work deals with the potential in an LNG ship propulsion system to reduce fuel consumption through controlled load distribution between engines in Dual Fuel Diesel Electric (DFDE) plant. Based on cyclical data acquisitioning measured on board and using an optimization model, the study evaluates different load distribution strategies between set up according to the optimization model results and automatic (equal) operation to determine their effectiveness in improving fuel efficiency. The analysis includes scenarios with different fuel types, including LNG, MDO and HFO, at different engine loads. The results indicate that load distribution adjustment based on the optimization model results significantly improves fuel efficiency compared to conventional methods of uniform load distribution controlled by power management systems almost in all load intervals. This research contributes to the maritime industry by demonstrating that strategic load management can achieve significant fuel savings and reduce environmental impact, which is in line with global sustainability goals. This work not only provides a framework for the implementation of more efficient energy management systems on LNG vessels, but also sets a benchmark for future innovations in maritime energy optimization as well as in the view of exhaust emission reduction.

The maneuverability of ships is influenced by several factors, including ship design, size, propulsion system, hull shape, and external conditions such as wind, waves, and currents. The size, shape, and arrangement of the hull, rudder, and propeller are decisive for maneuverability. Hydrodynamic forces such as bank effect and squat significantly impact the maneuverability of large ships in narrow channels. With the increasing trend of building ever-larger ships, the demand to evaluate the maneuvering performance of the ship at the design stage has become more critical than ever. Both experimental and computational methods are used to obtain accurate maneuvering characteristics of vessels. In this study, the methods for predicting ship maneuvering characteristics are analyzed using a systematic review based on the preferred reporting items for systematic reviews and meta-analyses (PRISMA). This article contributes to a deeper understanding of the hydrodynamic capabilities of ships and identifies possible future challenges in the field of ship hydrodynamics. The findings inform educators and the shipping industry about the importance of predicting the maneuvering performance of ships, with an emphasis on the education and training of seafarers needed to make timely decisions in critical situations.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Fungi are rich sources of secondary metabolites of agrochemical, pharmaceutical and food importances, such as mycotoxins, antibiotics and antitumor agents. Secondary metabolites play vital roles in fungal pathogenesis, growth and development, oxidative status modulation, and adaptation/resistance to various environmental stresses. LaeA contains an S-adenosylmethionine binding site and displays methyltransferase activity. The members of velvet proteins include VeA, VelB, VelC, VelD and VosA, for each member with a velvet domain. LaeA and velvet proteins can form multimeric complexes such as VosA-VelB and VelB-VeA-LaeA. They belong to global regulators and are mainly impacted by light. One of their most important functions is to regulate gene expression that are responsible for secondary metabolite biosynthesis. The aim of this mini-review is to represent the newest cognition on the biosynthetic regulation of mycotoxins and other fungal secondary metabolites by LaeA and velvet proteins. In most cases, LaeA and velvet proteins positively regulated production of fungal secondary metabolites. The regulated fungal species mainly belong to the toxigenic fungi from the genera of Alternaria, Aspergillus, Botrytis, Fusarium, Magnaporthe, Monascus, and Penicillium for the production of mycotoxins. We can control secondary metabolite production to inhibit the production of harmful mycotoxins while promoting the production of useful metabolites by global regulation of LaeA and velvet proteins in fungi. Furthermore, the regulation by LaeA and velvet proteins should be a practical strategy in activating silent biosynthetic gene clusters (BGCs) in fungi to obtain previously undiscovered metabolites.

Inflammatory bowel disease (IBD) is characterized by chronic inflammation of the gastrointestinal tract and encompasses two main subtypes, Crohn’s disease (CD) and ulcerative colitis (UC). IBD is frequently accompanied by extraintestinal manifestations (EIMs), with axial and peripheral spondyloarthritis (SpA) being the most common. Enthesitis, an inflammation of the bone insertions of capsules, ligaments, and tendons, represents an initial lesion in SpA. However, enthesitis remains an underestimated and often obscured EIM. The early detection of subclinical enthesial involvement in IBD patients using ultrasound (US) could provide an opportunity for timely intervention. While previous meta-analyses have reported on the incidence and prevalence of SpA in IBD, specific attention to enthesitis has been lacking. Therefore, this narrative review aims to resume the current knowledge on existing IBD-SpA cohorts, focusing specifically on enthesitis.

Leakage is important in groundwater cycle research and water resource management, the key is to construct the spatial distribution of aquitard. Influenced by natural and anthropogenic factors, the density of boreholes restricts the accuracy of aquitard structure. This paper explores the K-Nearest Neighbor (KNN) method to construct multi-layer aquitard structure in the hinterland of Songnen Plain, Northeast China, with limited boreholes, and compare it with Inverse Distance Weight (IDW) and Ordinary Kriging (OK) methods to evaluate the leakage. The KNN needs to first identify the eigenvalue-k of each layer, which is used to enhance the trainset to obtain the testset with a larger amount of sample data enhanced, and to make a prediction to obtain the 3-dimensional structure of aquitard. KNN is more accurate than the IDW and OK. The aquitrad structure obtained by the KNN is different from the IDW and OK, the thickness difference is 3.53%-54.00%, the area difference is 2.28%-23.91%, and the difference in leakage can be up to 24.51%. KNN also has a high degree of identification of aquitard edges, which can help the prevention of groundwater pollution. The results provide guidance for water balance analysis, borehole engineering design, water resources management and exploitation.

Three-dimensional (3D) geological modeling technology offers intricate geological information services and technical support for the research of urban geological conditions and their evolutionary mechanisms. It further facilitates the analysis of environmental geological problems, encompassing their distinguishing features and genetic mechanisms. The precision of such three-dimensional models is predominantly influenced by the caliber of modeling data, the chosen modeling methodologies, and the intricacy of the modeled geological objects. This research, exemplified by the three-dimensional geological structure modeling of the Wuhan metropolitan development area, aims to explore a comprehensive three-dimensional modeling framework for urban geology, particularly in scenarios with large-scale and complex geological conditions. This study holds significant technical value in enhancing the application of 3D geological modeling, as well as practical importance for urban geological investigations and research.

Existing research indicates that mineralization of Carlin-type gold deposit is related to geological structures, but current studies mostly focus on the qualitative association, and lack quantitative analysis of the relationship between mineralization and structural features, which limits the potential for predictive mineral exploration. In this study, the Nibao Carlin-type gold deposit was selected as the research area to conduct three-dimensional geological modeling, spatial analysis, and three-dimensional prospectivity modeling. Spatial analysis revealed that the majority of gold ore bodies are situated near the main fault, with gold mineralization primarily occurring within a spatial range of approximately -80 meters to 20 meters from the main fault plane. This spatial distribution predominantly aligns in a SW-NE direction. Spatial characteristic extraction of fault slope indicators suggests that the slope angles are conducive to the migration and accumulation of ore-forming hydrothermal fluids, with ore body metal content rapidly increasing within an angle range of approximately 20° to 60°. The shape analysis of the mainfault indicates that the principal spaces of mineralization enrichment are within -10m to 20m of the fault plane undulations, where gold resources are concentrated in a relatively flat area. However, the degree of mineralization is more pronounced in the protruding sections than in the depressed areas. The areas with significant dip changes in faults display higher variations in orebody attitudes, with mineralization noticeably weaker in areas where the fault steepness changes markedly. Ore-bearing units exhibit significantly higher grades within the -17° to 3° interval of fault steepness transition. This interval also sees a rapid accumulation of gold resources. The Nibao gold mine's mineralization is derived from deep, ore-bearing hydrothermal fluids ascending along major fractures, precipitating, and accumulating in favorable ore-hosting spaces (faults, anticline cores) and lithological combinations (sedimentary tuffs, tuffs). Three deep potential gold targets were identified, highlighting the deep western edge of the F1 fault and the deep southeast-trending lower plate as prospective areas for future exploration. This study underscores the effectiveness of 3D prospective modeling as an indispensable tool for elucidating the spatial distribution of fault-controlled Carlin-type gold deposits and their tectonic determinants.

Background/Objectives: RAS is associated with coronary artery disease (CAD), exacerbation of arterial hypertension and progression to heart failure, but remains frequently unrecognised in clinical practice. Methods: We conducted a systematic review and meta-analysis of studies by pooling data of patients undergoing CAG due to suspected or stable CAD that received a bilateral renal artery angiography; Results: A total of 31 studies with 31,689 patients were included (mean age 63.2±8.7 years, 20.9% were female). Overall, 13.4% (95%CI 10.5-16.7%) of patients undergoing coronary angiography had significant RAS, with 6.5% (95% CI 4.5-8.9%) and 3.7% (95%CI 2.5-5.2%) having severe and bilateral RAS. The mean weighted proportion of patients with 3-vessel coronary disease (3VD) was 25.1 (95%CI 19.6-30.9%) while 4.2% (95%CI 2.6-6.2%) had leftmain (LM) coronary disease. Patients with RAS compared to those without RAS were significantly older (mean difference - MD 4.2 years, (95%CI 3.8-4.6). The relative risk of RAS was greater for the female sex (risk ratio, 95%CI; RR 1.3, 1.03-1.57), presence of diabetes (RR 1.2, 1.10-1.36), arterial hypertension (RR 1.3, 1.21-1.46), dyslipidemia (RR 1.1, 1.06-1.14), peripheral artery disease-PAD (RR 2.1, 1.40-3.16), chronic kidney disease-CKD (RR 2.6, 2.04-3.37), 3VD (RR 1.6, 1.30-1.87), and LM disease (RR 1.8, 1.28-2.47). Smoking had a neutral effect on the risk of RAS occurrence (RR 1.0, 0.94-1.06); Conclusions: RAS is common in patients undergoing coronary angiography. CKD, PAD, older age, and severe CAD were among the strongest predictors for the presence of significant RAS.

The ordinary 3D wave equation for nondissipative, homogeneous, isotropic media admits solutions where the point sources are permitted to move, but it does not admit solutions where the receiver is allowed to move. To overcome this limitation, the new wave equation is derived, permitting both the receiver and the source to move. This new wave equation is a generalization of the standard wave equation, and it reduces to the standard wave equation when the receiver is at rest. To derive this new wave equation, we first mathematically define a diverging spherical wave caused by the stationary point source. From this purely mathematical definition, the wave equation for the stationary source and the moving receiver is derived together with the corresponding free-space Green's function. Utilizing the derived Green's function, it was shown that this new wave equation also permits the solutions where both the receiver and the source are permitted to move. In conclusion, this paper demonstrates that, instead of an ordinary wave equation, the wave equation for the moving source and the moving receiver governs the waves emitted by the moving point sources and received by the moving receivers.

The present grievous situation of the tuberculosis disease can be improved by efficient case management and timely follow-up evaluations. With the advent of digital technology this can be achieved by quick summarization of the patient-centric data. The aim of our study was to assess the effectiveness of the ODK Scan paper-to-digital system during testing period of three months. A sequential, explanatory mixed-method research approach was employed to elucidate technology use. Training, smartphones, application and 3G enabled SIMs were provided to the four field workers. At the beginning, baseline measures of the data management aspects were recorded and compared with endline measures to see the impact of ODK Scan. Additionally, at the end, users’ feedback was collected regarding app usability, user interface design and workflow changes. 122 patients’ records were retrieved from the server and analysed for quality. It was found that ODK Scan recognized 99.2% of multiple choice bubble responses and 79.4% of numerical digit responses correctly. However, the overall quality of the digital data was decreased in comparison to manually entered data. Using ODK Scan, a significant time reduction is observed in data aggregation and data transfer activities, however, data verification and form filling activities took more time. Interviews revealed that field workers saw value in using ODK Scan, however, they were more concerned about the time consuming aspects of the use of ODK Scan. Therefore, it is concluded that minimal disturbance in the existing workflow, continuous feedback and value additions are the important considerations for the implementing organization to ensure technology adoption and workflow improvements.

Dolichandrone spathacea is a rare and endangered semi-mangrove plant species with an extremely small population, naturally distributed only in Zhanjiang City and the east coast of Hainan Island, China. Regrettably, the present situation of the D. spathacea population in China has not yet been carefully investigated. In this study, we aim to evaluate the current resource status and population dynamic characteristics of D. spathacea on Hainan Island, China, in order to propose sustainable conservation and management strategies for future ecological restoration of its natural population. Our results show that D. spathacea on Hainan Island can be divided into four populations. All the D. spathacea populations present a state of overall dispersion, local concentration, and occasionally sporadic existence, and they exist in geographical isolation. The young, middle, and old D. spathacea plants account for 20.42%, 66.20%, and 13.38%, respectively, indicating that the overall age class of the D. spathacea population on Hainan Island belongs to a declining type. Furthermore, instead of temporal structure, we chose diameter at breast height (DBH) to establish a static life table, draw a population survival curve, and quantify the future development trend through population dynamic analysis and time-series prediction. These results directly point out that the D. spathacea population on Hainan Island is sensitive to external disturbances and possesses two main increases in mortality rate—namely, in its juvenile and mature stages—due to weak vitality, competition, and anthropogenic interferences, which are the most important reasons for its endangered status. Depending on the current conditions of the D. spathacea population, we should conserve and expand mature trees in situ, preserve their germplasm resources, rehabilitate their habitats to promote provenance restoration, and conduct artificial cultivation and spreading planting in order to realize the sustainable conservation and management of D. spathacea.

Water samples for bacterial microbiome studies undergo a biomass concentration, DNA extraction and taxonomic identification steps. Through benchmarking, we studied the applicability of Skimmed milk flocculation (SMF) for bacterial enrichment, an adapted in-house DNA extraction protocol, and six 16S rRNA databases (16S-DBs). Surface water samples from two rivers were treated with SMF and Vacuum filtration (VF) and subjected to amplicon or shotgun metagenomics. A mock community standard underwent five DNA extraction protocols, taxonomical identification with six different 16S-DBs and evaluated by the Measurement Integrity Quotient (MIQ) score. In SMF samples, the skimmed milk was metabolized by members of lactic acid bacteria or genera such as Polaromonas, Macrococcus, and Agitococcus, resulting in increased relative abundance (p < 0.5) up to 5.0 log fold change compared to VF, rendering SMF inapplicable for bacterial microbiome studies. The best performing DNA extraction protocols were FastSpin Soil, the in-house method and EurX. All 16S-DBs yielded comparable MIQ scores within each DNA extraction kit, ranging from 61-66 (ZymoBIOMICs) up to 80-82 (FastSpin). DNA extraction kits exert more bias to the composition than the 16S-DBs. This benchmarking study presented valuable insights to inform future water metagenomic study designs.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

This paper is aimed at studying the temporal evolution of the surface displacements occurred over the past few years in the ocean-reclaimed platforms of the Shanghai megacity (China), which are mainly ascribable to consolidation processes of large dredger fills and alluvial deposits. With respect to previous analyses carried out over the same area, this work provides a joint multi-platform differential interferometry synthetic aperture radar (DInSAR) analysis, based on the application of the advanced Small BAseline Subset (SBAS) algorithm. This led us to retrieve long-term deformation time-series that are helpful for a better understanding of the on-going deformation phenomena. To this aim, we have exploited two sequences of SAR data collected by the ASAR/ENVISAT and by the COSMO-SkyMed (CSK) sensors, respectively, spanning the whole time period from 2007 to 2016. Unfortunately, the large time gap (of about three years) existing between the available ASAR/ENVISAT and CSK datasets gave rise to additional difficulties for their combination. Nevertheless, this problem has been faced by benefiting from the knowledge of a time-dependent model describing the temporal evolution of the expected deformations affecting the Shanghai ocean-reclaimed platforms.

Industrial fires at facilities including waste management sites, warehouses, factories, chemical works and fuel storage depots are relatively frequent occurrences. Often, these fires occur adjacent to urban communities and result in ground-level airborne pollutant concentrations that are well above guideline values. Land, water, livestock and crops may also be contaminated by the emissions and by firefighting activities. Moreover, impacted communities tend to have a higher proportion of minority ethnic populations, individuals with underlying health vulnerabilities, as well as those of lower socio-economic status. Nevertheless, this is an aspect of air quality that is under-researched, and so this review aims to highlight the public health hazards associated with industrial fires and the need for an effective, coordinated, public health response. We also review the range of monitoring techniques that have been utilised in such fires and highlight the role of dispersion modelling in predicting plume trajectories and in estimating population exposure. We recommend establishing 1-h guideline values for particulate matter to facilitate timely public health interventions and we highlight the need to review regulatory and technical controls for sites prone to fires, particularly in the waste sector.

Shared public buildings have become centers of innovation, integrating advanced technologies to meet evolving societal needs. With a heightened emphasis on occupants’ health and well-being, these buildings serve as hubs for technological convergence, facilitating seamless connectivity and intelligent data analysis and management. Within this context, environmental monitoring emerges as a foundational element, pivotal to all aspects of building management. This article provides findings from the nationally funded RE-START project, which focuses on shared public buildings, with special regard to educational and medical facilities. The project explores enhanced indoor air quality monitoring, focusing in particular on CO2 concentration that is directly correlated with occupancy, as a fundamental element for developing health and safety protocols, energy efficiency strategies, integration of smart building technologies, and data-driven energy management. The intersection of environmental monitoring, energy efficiency, security, and IoT technologies in in indoor spaces are relevant. The outcomes of the study reveal the delicate nature of all the involved components, that need to be carefully developed in an integrated manner.

Whole cell biosensors could serve as eco-friendly and cost-effective alternatives for detecting potentially toxic bioavailable heavy metals in aquatic environments. However, they often fail to meet practical requirements due to an insufficient limit of detection (LOD) and high background noise. In this study, we designed a synthetic genetic circuit specifically tailored for detecting ionic mercury, which we applied to environmental samples collected from artisanal gold mining sites in Peru. We developed two distinct versions of the biosensor, each utilizing a different reporter protein: a fluorescent biosensor (Mer-RFP) and a colorimetric biosensor (Mer-Blue). Mer-RFP enabled real-time monitoring of the culture’s response to mercury samples using a plate reader, whereas Mer-Blue was analysed for colour accumulation at the endpoint using a specially designed, low-cost camera set up for harvested cell pellets. Both biosensors exhibited negligible baseline expression of their respective reporter proteins and responded specifically to HgBr2 in pure water. Mer-RFP demonstrated a linear detection range from 1 nM to 1 μM, whereas Mer-Blue showed a linear range from 2 nM to 125 nM. Our biosensors successfully detected a high concentration of ionic mercury in the reaction bucket where artisanal miners produce a mercury-gold amalgam. However, they did not detect ionic mercury in the water from active mining ponds, indicating a concentration lower than 3.2 nM Hg2+ -a result consistent with chemical analysis quantitation. Furthermore, we discuss the potential of Mer-Blue as a practical and affordable monitoring tool, highlighting its stability, reliance on simple visual colorimetry, and the possibility of sensitivity expansion to organic mercury.

Danyore Valley area is a new prospect of copper-gold mineralization in the Gilgit-Baltistan province, Kohistan terrane, northern Pakistan. The mineralization is Cu-Au vein-type, localized within quartz veins and controlled by a fracture system mainly trending NW and NE. The host units belong to the Ladakh-Kohistan arc terrane, which covers northern Pakistan and north-western India and mainly comprises Precambrian basement units, Paleozoic to Cenozoic magmatic rocks, and sedimentary strata. The mineralized wall rocks consist of Mesozoic gabbro and diorite, which have undergone an intensive hydrothermal alteration. The study area, Danyore Valley, has yet to be explored. The geological background and mineralization type in literature are scarce. Moreover, the tectonic setting, petrogenesis, age, and magmatic evolution of the gabbro-diorite hosting unit still need to be better understood. Furthermore, the sources of metals and mineralized fluids and the types of mineralization and alteration are also unexplored. This research's contribution presents the field investigation, microscopic observations, whole rock geochemistry (major, trace, and REE), mineral analysis (EPMA), in situ LA–ICP–MS zircon U–Pb age dating, and zircon trace elements data for Danyore Valley Cu-Au prospect of Kohistan Batholith. The current research work's objectives are to (a) constrain the emplacement ages of the Danyore Valley host rocks, (b) determine the petrogenesis and tectonic environment of the gabbro-diorite wall rocks, and (c) identify the mineralization style and alteration patterns of Cu-Au occurrences. The U-Pb isotopic data of studied zircons from Danyore Valley diorite specimens yielded concordia ages from 111.60 ± 0.90 Ma to 112.18 ± 0.74 Ma. Correspondingly, the gabbro rock sample displayed a concordia age of 110.21 ± 0.99 Ma, indicating the crystallization time of the host bodies is mainly the early cretaceous period (∼110 Ma). The findings of this study reveal that the calc-alkaline affinity and arc-like geochemical characteristics of the gabbro and diorite rocks have been characterized by a significant enrichment in large-ion lithophile elements and an apparent depletion in high-field strength elements. The parent magma probably originated from a partial melting process of mantle depletion, and geochemical traits are characteristic of magmas associated with subduction zones. The Danyore Valley area of Kohistan terrane is defined by the existence of several mineralized quartz veins, which are mainly sulfide assemblages. The sulfide ore is mainly comprised of chalcopyrite, pyrite, and bornite, with a smaller amount of covellite and sphalerite and significant traces of gold, which are distributed mainly in sulfides. Copper and gold mineralization of Danyore Valley is associated with phyllic, propylitic, and carbonatization alteration assemblages. Metal-rich quartz veins exhibit a spatial correlation with diorite and gabbro rocks. The discovery of several surface Cu-Au vein-type mineralized areas accompanying outcrops of copper supergene enrichment at the Danyore Valley prospect is significant evidence (predictor patterns) of porphyry-style deposits in the Gilgit district, Kohistan terrane, northern Pakistan. This work also advocates the importance of the Danyore Valley prospect and Kohistan Batholith region for further detailed geological studies.

The present work aimed to validate a low-cost passive monitoring procedure. For its validation, the monitoring of atmospheric organic pollutants - polycyclic aromatic hydrocarbons (PAH) was carried out in a capital of the central-western region of Brazil. The sensors were fixed on poles intended for electrification during the dry season. After 15 days, samples were extracted by solvent extraction and analysed by High-Resolution Gas Chromatography with Flame Ionization Detector (HRGC-FID). For the validation of the procedure, PAHs monitored and standardised by the American Environmental Agency (EPA), a benchmark for environmental monitoring of air quality by several countries, were analysed. The results demonstrated that the low-cost passive monitoring method was effective in the quantification of PAH in the environment-air, capable of being used by countries that do not have many resources for monitoring air quality.

The leather industry is one of the most polluting industries in the world due to the large amounts of waste following the raw hides processing, but also due to the high content of chemicals present in their composition. The main problem of chromium-tanned leather solid waste is related to their storage, because of the ability of chromium to leach in soil or water, and also owing to the high ability of trivalent chromium to oxidize to its toxic form, hexavalent chromium. The purpose of this study is to present the latest methods for extracting trivalent chromium from the composition of solid leather wastes. The extraction methods identified in the present study are based on acid/basic/enzymatic hydrolysis and substitution with the help of organic chelators (organic acids and organic acid salts). In addition, the study includes a comparative analysis between the advantages and disadvantages of each identified extraction method. At the same time, the study also presentes alternative chromium extraction methods based on the combination of conventional extraction methods and ultrasound-assisted extraction.

Dinoflagellates are one of the largest groups of marine microalgae and exhibit diverse trophic strategies. Within these niches, dinoflagellates can produce secondary metabolites that are known to be toxic, which can lead to ecologically harmful blooms. Amphidinium carterae is one species of dinoflagellate that produces toxic compounds and is used as a model for dinoflagellate studies. The extent to which the microbiome surrounding A. carterae affects its growth and secondary metabolite synthesis is still being assessed, as well as the impact of bacterial data on sequencing and assembly. An antibiotic cocktail was previously shown to eliminate 16S amplification from the dinoflagellate culture. Even with drastically reduced bacterial numbers, bacterial populations are likely to be present. In this experiment we used novel Nanopore long-read sequencing techniques on A. carterae cultures to assemble 15 full bacterial genomes ranging from 2.9-6.0 Mb and found that the use of antibiotics decreased the percentage of reads mapping back to bacteria. We also identified shifts in the microbiome composition and identified a potentially deleterious bacterial species arising in the absence of the antibiotic-treatment. Multiple antibiotic-resistance genes were identified, as well as evidence that the bacterial population do not contribute to toxic secondary metabolite synthesis.

This study explores the implementation of the ANSI/373: Sustainable Production of Natural Dimension Stone standard within the North American dimension stone industry to identify driving forces behind the initiative and consider potential outcomes as it advances. The method involves a thorough review of ANSI/373, comparing it with voluntary sustainability initiatives (VSIs) in the forest industry to assess its effectiveness and challenges, and semi-structured interviews with contacts in the dimension stone field. Key drivers such as corporate social responsibility and market pressures influence the adoption of sustainability standards. The results highlight the embedded environmental considerations within the emerging dimension stone standards and their implications for sustainable practices in the industry. While the ANSI/373 standard promotes sustainable awareness and practices, it faces challenges in certification credibility and industry acceptance, particularly due to inconsistency among firms in their response, rigorous certification demands, and skepticism about certification credibility. The research advocates for enhanced collaborative frameworks to increase the standard’s adoption and impact, suggesting that industry stakeholders prioritize showcasing dimension stone as a practical, environmentally considerate material.

Water quality assessment in pastoral of Tibetan Plateau, which is water sources for about 40% of world's population and the runoff-yield area of Yellow rivers, is very important. In this paper, Xiahe county which belongs to Tibetan Plateau pastoral was investigated. Six parameters(via, chloride, COD, ammonia nitrogen, nitrate, fluoride, sulfate) were selected to assess the water quality and health degree by using fuzzy comprehensive evaluation methods. The hydrochemical type in surface water was of HCO3--Mg2+-Ca2+ type. The cations and anions in surface water were mainly from weathering and dissolution of carbonate rock. Results showed that the water quality in all 69 sampling sites was all of class Ⅰ. The integrated health degree reached more than 0.85 and the health rate were 100%. Although ammonia nitrogen was regarded as the main contamination factor, but it had a little effect on the entire body of water. Overall, the surface water qualities of most samples in Xiahe County was good condition.

For the last two decades, an increasing demand for low-cost adsorbents for drinking water treatment has been challenged in the rural areas of developing countries that have problems with arsenic (As) contamination. In this work, spent bleaching earth (SBE), a residual material that is formed during the process of refining vegetable oil, has been utilized to prepare the new magnetic adsorbent Fe-SBE/C by modifying its surface area through calcination and co-precipitation with iron. The experimental results demonstrate that Fe-SBE/C exhibits a substantial adsorption capacity towards both arsenite (As(III)) and arsenate (As(V)). Optimal pH conditions were found to be pH 10 for As(III) and pH 3 for As(V), resulting in adsorption percentages of 76.7% and 94.1%, respectively. Other experimental parameters such as calcination conditions, adsorbent dosage, iron-loading ratio, and the presence of co-existing ions were thoroughly investigated. The kinetic study revealed that the adsorption processes follow the Elovich and intraparticle diffusion models, suggesting a combined adsorption mechanism of boundary layer control and chemisorption. Furthermore, the isotherm followed the Langmuir model with a maximum adsorption capacity of 202.61 μg g-1 for As(III) and 187.61 μg g-1 for As(V). Through thermodynamic analysis and reinforcement by activation energy data, this research validates that the observed adsorption process is indicative through chemisorption. The regeneration study revealed the potential for multiple cycles of arsenic removal, highlighting the practical applicability of Fe-SBE/C in environmental contexts. In conclusion, the findings of this study underscore the efficacy of Fe-SBE/C in arsenic removal and present it as a promising and environmentally friendly solution for mitigating arsenic pollution.

Mixed plastic packaging waste sorting residues (MPO323) were treated by thermal pyrolysis to utilize pyrolysis oil and char. The pyrolysis oil was found to contain aromatic and aliphatic hydrocarbons. Chlorine and bromine contents were up to 40,000 mg/kg and 200 mg/kg, respectively. Additionally, other elements like sulfur, phosphorous, iron, aluminum, and lead were detected, which can be interpreted as impurities regarding the utilization of the oils by means of chemical recycling. The pyrolysis char showed high contents of potentially active species like silicon, calcium, aluminum, iron, and others. To enhance the content of aromatic hydrocarbons and to reduce the level of contaminants, the pyrolysis oil was reformed with the corresponding pyrolysis char to act as an active material in a fixed bed. The temperature of the reactor and the flow rate of the pyrolysis oil feed were varied to gain insights on cracking and reforming reactions as well as on the performance with regard to decontamination.

Lirianthe delavayi has valuable ornamental and medicinal value, is an important economic tree, and has a long history of cultivation. As important regulatory molecules, miRNAs are involved in important physiological processes, such as the plant stress response, organ morphogenesis, hormone secretion, and signaling. In this study, based on miRNA sequencing analysis of wild and cultivated Lirianthe delavayi, we explored the differences in posttranscriptional regulation during the cultivation of Lirianthe delavayi from the aspect of miRNA molecular regulation. The results revealed the following: 1. A total of 365 miRNAs were sequenced and identified, and their first bases had obvious uracil (U) base preferences. Among them, 242 miRNAs were classified into 32 miRNA families; 2. Analysis of miRNA expression differences revealed that 39 miRNAs had significant expression differences between wild and cultivated populations; 3. Bioinformatics target gene prediction and target gene enrichment analysis of significantly differentially expressed miRNAs revealed that the target genes were significantly enriched in plant‒pathogen interactions, sphingolipid metabolism, defense responses, and ADP binding. 4. The plant‒pathogen interaction pathway involves seven differentially expressed miRNAs and 30 miRNA‒target gene regulatory pairs, which are involved mainly in pathogen signature molecule recognition and binding, signal transduction, and the regulation of disease resistance molecules or gene expression; Ath-MIR169g-p3_2ss7AG19GA, ath-MIR169g-p5_2ss7AG19GA, and ath-miR408-3p_L-3 are expressed only in wild population, and it is hypothesized that the domestication process from wild to cultivation species may be accompanied by the loss of disease resistance-related miRNAs. This study provides a reference for exploring the posttranscriptional-level regulatory mechanisms of adaptive changes in Lirianthe delavayi from wild to cultivated.

The Axillary Seabream Pagellus acarne is of economic importance for recreational and commercial fisheries in the Atlantic and the Mediterranean, but a decline in total landings has been observed and raised some concern. Although biological information on the species has been provided for the Atlantic and Mediterranean, in the Portuguese continental slope data is restricted to the southern part of the country, which points to the relevance of the present work. A total of 520 individuals, between 7.8 cm and 39.9 cm TL, were monthly collected from September 2020 to August 2022 from commercial landings of fishing vessels operating off mainland Portugal, and used to study age and growth, the reproductive strategy and the annual sexual cycle. Age varied between 0 years (7.8 cm TL) and 15 years (34.2 cm TL) and the von Bertalanffy growth parameters were estimated from whole-otolith readings (L∞ = 35.2 cm, k = 0.133 yr–1 and t 0 = –2.78 yr). Pagellus acarne proved to be a protandric hermaphrodite species with males prevailing until 28.0 cm TL and females between 28.0 cm and 34.0 cm TL with a brief sex change phase. Females presented asynchronous oocyte development with a batch spawning pattern. The spawning season occurred from April to October with a spawning peak between June and August aas shown by histological analysis of the gonads and high levels of GSI during the period.

This paper proposes a new kind of airship actuator configuration for surveillance and environmental monitoring missions. We present the design and application of a 6-propeller electrical airship (Noamini) with independent tilting propellers, allowing improved and flexible maneuverability. The vehicle has different combinations of differential propulsion and can be used in 2, 4 or 6 motors configuration. We developed a high-fidelity airship simulator for the Noamini airship, which was used to test and validate a control-guidance approach. Incremental Nonlinear Dynamic Inversion (INDI) is used for the velocity/attitude control to follow a high-level L1 guidance reference in a simulated waypoint tracking mission with wind and turbulence. The proposed framework will be soon implemented in the onboard control system of the Noamini, an autonomous airship for environmental monitoring and surveillance applications.

Recently, there has been growing interest in using smart eHealth systems to manage asthma. However, limitations still exist in providing smart services and accurate predictions tailored to individual patients’ needs. This study aims to develop an adaptive ubiquitous computing framework that leverages different bio-signals and spatial data to provide personalized asthma attack prediction and safe route recommendations. We proposed a smart eHealth framework consisting of multiple layers that employ telemonitoring application, environmental sensors, and advanced machine-learning algorithms to deliver smart services to the user. The proposed smart eHealth system predicts asthma attacks and uses spatial data to provide a safe route that drives the patient away from any asthma trigger. Additionally, the framework incorporates an adaptation layer that continuously updates the system based on real-time environmental data and daily bio-signals reported by the user. The developed telemonitoring application collected a dataset containing 665 records used to train the prediction models. The testing result demonstrates a remarkable 98% accuracy in predicting asthma attacks with a recall of 96%. The eHealth system was tested online by ten asthma patients, and its accuracy achieved 94% of accuracy and a recall of 95.2% in generating safe routes for asthma patients, ensuring a safer and asthma-trigger-free experience. The test shows that 89% of patients were satisfied with the safer recommended route than their usual one. This research contributes to enhancing the capabilities of smart healthcare systems in managing asthma and improving patient outcomes. The adaptive feature of the proposed eHealth system ensures that the predictions and recommendations remain relevant and personalized to the current conditions and needs of the individual.

This paper presents the results of an experimental investigation about target detecting with passive sonar in Persian Gulf. Detecting propagated sounds in the water is one of the basic challenges of the researchers in sonar field. This challenge will be complex in shallow water (like Persian Gulf) and noise less vessels. Generally, in passive sonar the targets are detected by sonar equation (with constant threshold) which increase the detection error in shallow water. Purpose of this study is proposed a new method for detecting targets in passive sonars using adaptive threshold. In this method, target signal (sound) is processed in time and frequency domain. For classifying, Bayesian classification is used and prior distribution is estimated by Maximum Likelihood algorithm. Finally, target was detected by combining the detection points in both domains using LMS adaptive filter. Results of this paper has showed that proposed method has improved true detection rate about 27% compare other the best detection method.

Levels of trace element pollution in surface soil can be estimated using soil analyses and leaching tests. These methods may reveal different results due to the effect of soil properties, such as grain size and mineral composition, on elemental availability. Therefore, this study advocates an alternative method for monitoring and assessment of trace element pollution in surface soil using terricolous fruticose lichens. Lichens growing at abandoned mine sites and unpolluted areas in southwest Japan and their substrata were analyzed using inductively coupled plasma-mass spectrometry and X-ray fluorescence spectrometry to clarify the relationships between Cu, Zn, As, and Pb concentrations in lichens and soils, including their absorption properties. Concentrations of these elements in the lichens were positively correlated with those in the soils regardless of lichen species, location, habitat, or conditions of soils. The analyzed lichens had neither competitive nor antagonistic properties in their elemental absorption, which made them good biomonitors of trace element pollution in surface soil. The distribution maps of average Cu, Zn, As, and Pb concentrations at each sampling region detected almost all of the Cu, Zn, and As pollution of the soils. Therefore, lichens could be used in practical applications to monitor Cu, Zn, and As pollution in surface soils.

Abstract: Toxicity of emerging organic pollutants to photosystems of aquatic plants are still not well clarified. This study aimed to develop a novel ecotoxicological experimental protocol based on nanoscale electrochemical mapping of photosynthetic oxygen evolution of aquatic plants by SECM (scanning electrochemical microscopy). The protocol was also checked by confocal laser scanning microscopy (CLSM), the traditional Clark oxygen electrode method and chlorophyll fluorescence technique. The typical persistent organic pollutant 2,4-dichlorophenol (2,4-DCP) in water environment and the common aquatic Microsorium pteropus (M. pteropus) were chosen as the model organic pollutant and tested plant, respectively. It was found that the SECM method could well discriminated the responses of stoma micromorphology and spatial pattens of photosynthetic oxygen evolution on single stoma. The shape of stoma blurred with increasing 2,4-DCP concentration, which was in good agreement with the CLSM images. The dose-response curves and IC50 values obtained from the SECM data were verified by the data measured by the traditional Clark oxygen electrode method and chlorophyll fluorescence test. The IC50 value of single stoma oxygen emission of 24 h exposed plant leave, which was derived from the SECM current data (32535 μg L-1), was close to those calculated from the maximum photosynthetic efficiency (Fv/Fm) measured by chlorophyll fluorescence test (33963 μg L-1), and the Clark oxygen electrode method photosynthetic oxygen evolution rate (32375 μg L-1). The 72 h and 96 h 2,4-DCP exposure data further confirmed the reliability of the nanoscale stoma oxygen emission mapping methodology for ecotoxicological assessment. In this protocol, the procedures for how to collect effective electrochemical data and how to extract useful information from the single stoma oxygen emission pattern were well established. This study showed that SECM is a feasible and reliable ecotoxicological tool for evaluation of toxicity of organic pollutants to higher plants with unique nanoscale visualization advantage over the conventional methods.

MicroRNAs (miRNA) exert regulatory actions via base-pairing with their binding sites on target mRNAs. Cooperative-binding, i.e., synergism, among binding sites on a mRNA is biochemically well-characterized. We studied whether this synergism is reflected in global relationship between miRNA-mediated regulatory activity and miRNA-binding-site count on the target mRNAs, i.e., leading to a non-linear relationship between the two. Recently, using our own and public datasets, we have enquired into miRNA regulatory actions: first, we analyzed the power-law distribution pattern of miRNA binding sites; second, strikingly, mRNAs for core miRNA regulatory apparatus proteins have extra-ordinarily high binding site counts, forming self-feedback-control loops; third, we revealed that tumor suppressor mRNAs generally have more sites than oncogene mRNAs; and fourth, we characterized enrichment of miRNA target mRNAs in translationally less-active polysomes relative to more-active polysomes. In these four studies, obvious correlation was observed qualitatively between the extent to which a mRNA is miRNA-regulated and its binding sites count. This paper summarizes the used datasets. We also re-analyzed the correlation by comparative linear and non-linear regression analyses. The results support a non-linear, instead of linear, relationship between the two parameters, conceivably a transcriptome-level reflection of cooperative-binding/synergism among miRNA binding sites on a target mRNA.

The port environments have some structures that still need regular control. However, the nature of these environments presents a number of challenges in determining an accurate vehicle position and consequently performing successful image similarity detection. These scenarios, however, can have poor visibility conditions and are highly dynamic, making place recognition difficult because the appearance of a place can change over time. Under these operational conditions, imaging sonars are a promising solution. There are some factors that affect the quality of the captured images, but the fact that they do not suffer from haze is a plus. Therefore, in this paper, a purely acoustic similarity detection method based on forward-looking sonar (FLS) data is proposed to overcome the inherent perceptual problems in a port scenario. Considering the lack of available data in this context and to facilitate the variation of environmental parameters and sensor configurations, a port scenario was simulated using the Stonefish simulator. Experiments were conducted on predefined trajectories near structures. The place recognition approach performs better compared to the results obtained with optical imagery. In general, it provides a good compromise in terms of distinctiveness and achieves a performance of 87.5% when appropriate constraints and assumptions are made.

Selecting road networks in cartographic generalization has consistently posed formidable challenges, driving research towards the application of intelligent models. Despite previous efforts, the accuracy and connectivity preservation in these studies, particularly when dealing with road types of similar sample sizes, still warrant improvement. To address these shortcomings, we introduce a Heterogeneous Graph Attention Network (HAN) for road selection, where feature masking method is initially utilized to assess the significance of road features. Concentrating on the most relevant features, two meta-paths are introduced within the HAN framework: one for aggregating features of the same road type within the first-order neighborhood, emphasizing local connectivity, and another extending this aggregation to the second-order neighborhood, capturing a broader spatial context. For a comprehensive evaluation, we introduce a set of metrics considering both quantitative and qualitative aspects of the road network. Compared to traditional neural networks, our HAN model demonstrates superior accuracy and F1-score, particularly for road types with comparable samples. Additionally, it enhances the overall connectivity of the selected network. In summary, our HAN-based method provides an advanced solution for road network selection, surpassing previous approaches in terms of accuracy and connectivity preservation.

In this paper, we investigate a class of hierarchical variational inequalities (HVIPs, i.e., strongly monotone variational inequality problems defined on the solution set of multiple-set split common fixed point problems) with quasi-pseudocontractive mappings in real Hilbert spaces, which special cases can be found in many important engineering practical applications such as image recognizing, signal processing and machine learning. In order to solve HVIPs of potential application value, inspired by the primal-dual algorithm, we propose a novel accelerated cyclic iterative algorithm that combines the inertial method with a correction term and a self-adaptive step-size technique. Our approach eliminates the need for prior knowledge of the bounded linear operator norm. Under appropriate assumptions, we establish strong convergence of the algorithm. Finally, we apply our novel iterative approximation to solve multiple-set split feasibility problems and verify the effectiveness of the proposed iterative algorithm through numerical results.

The ECM is composed of a considerable number of biochemically and structurally diverse constituents. ECM is a highly dynamic system that constantly receives and sends biological, chemical and mechanical signals. Several studies suggest that mechanical signals derived from the extracellular microenvironment regulate skin regeneration and wound healing. We evaluated effects of a mixture of biomolecules extracted and purified from bovine colostrum on restoring the mechanical properties of ECM. Test measuring collagen contraction showed a significant difference in contraction activation in samples treated with the 2% colostrum derivative mixture compared to the control. The analysis of the supernatant showed an inhibition of metalloproteinase-2 expression and an increase in collagen secretion by fibroblasts in treatment samples. Our hypothesis is that the molecules extracted and purified from bovine colostrum restore the ECM environment qualitative and quantitative characteristics, thus guaranteeing through a mechanical action the restoration of the wound due to the transduction of the signal activated by the integrins.

Environmental monitoring is an important topic and serves a vibrant scientific role by revealing long-term trends that can lead to new knowledge and understanding. Globally, there is active development of photonic sensors incorporating multidisciplinary research. The ultimate objective is to develop small, low-cost, sensitive, selective, quick, durable, remote-controllable sensors that are resistant to electromagnetic interference. Different photonic sensor designs and advances in photonic frameworks have shown the possibility to realize these capabilities. In this review paper, the latest developments in the field of optical waveguide and fiber-based sensors which can serve for environmental monitoring are discussed. Several important topics such as toxic gas, water quality, indoor environment, and natural disaster monitoring are reviewed.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

The Tisza River is the longest tributary of the Danube, draining the eastern part of the Carpathian Basin (Central Europe). Five countries share its catchment with different waste production and management practices. Large amounts of waste, including macroplastics (MaPs), are washed into the river. Some of the litter is trapped by the riparian vegetation forming litter accumulations. The study aimed to map the amount of litter by a citizen science program and remote sensing data and to compare the MaP data to the amount of microplastic fragments in sediments. Volunteers reported 3216 riverine litter accumulations from five countries along the entire length of the Tisza (2016–2022). The results suggest that low flow conditions (e.g., impoundment by dams) support litter and MaP trapping. The volume of large accumulations registered by the citizens showed a good correlation with the area of drifting litter revealed on Sentinel-2 images (2015–2021) using machine learning algorithms. Though the MaPs probably fragmentate during their fluvial transport, no clear connection was found between the volume of litter accumulations and the mean microplastic fragment content of sediments (2019–2022). The “Clean Tisza Map“ reveals the high degree of stranded pollutants along rivers and supports public cleanup activities.

The objective of this study was to investigate the concentration and spatial distribution patterns of six potentially toxic heavy metal elements (Mn, Zn, Cr, Pb, Cu and Ni) in bus station dusts in the Xifeng district of Gansu province, NW China. The contents were analyzed for Mn, Zn, Cr, Pb, Cu and Ni by using S8 TIGER Brochures wavelength dispersive X-ray fluorescence spectrometry. Geoaccumulation index (Igeo ), enrichment factor (EF), pollution index (PI) and integrated pollution index(IPI) were calculated to evaluate the heavy metal contamination level of bus station dusts. The results indicate that, in comparison with the background values of local soil, bus station dusts in Xifeng have elevated metal concentrations as a whole. The concentrations of heavy metals investigated in this paper are compared with the reported data of other cities. The results show that the arithmetic means of Mn, Zn, Cr, Pb, Cu and Ni are 440.8, 137.9, 60.0, 42.8, 33.5 and 19.8mg kg−1 respectively. The mean values of Igeo reveal the order of Ni<Mn<Cr<Cu<Zn<Pb. The high Igeo and EF for Cu, Zn and Pb in bus station dusts indicate that there is a considerable Cu, Zn and Pb pollution, which mainly originate from traffic and industry activities. The Igeo and EF of Ni, Mn and Cr are low and the assessment results indicate an absence of distinct Ni, Mn and Cr pollution in bus station dusts. The assessment results of PI also support Cu, Zn and Pb in bus station dusts presented middle pollution, and IPI indicates heavy metals of bus station dusts polluted seriously.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.

This bibliometric analysis delves into the realm of botanical gardens through the process of mapping literature and discerning research frontiers, underlying themes, and interconnections within the extant body of knowledge. The study uses a dataset of 1340 publications and employs methodologies such as authors' keywords co-occurrence data to examine the discipline's trends, patterns, and knowledge gaps. The study finds significant growth in literature from 1960 to 2023, emphasizing botanical gardens, conservation, taxonomy, biodiversity, ex-situ conservation, and diversity. Key influencers such as Sanja Kovačić, Elaissi, and Chemli have steered research directions towards ex-situ conservation and essential oils, reflecting the field's interdisciplinary nature. The study shows global institutional variation, with entities like the Chinese Academy of Sciences, the Royal Botanic Gardens UK, and the New York Botanical Garden US leading the discourse. Thematic analyses have identified core themes and emerging research topics, with ecological restoration, essential oils, invasive species, and climate change mirroring the field's expanding scope. The consistent prevalence of themes such as 'botanical gardens' and 'conservation' over time underscores their enduring significance. Emerging topics like climate change and biodiversity are gaining prominence, signaling a shift in research priorities. The expanding array of subjects, including 'invasive species' and 'genetic diversity,' indicates an amplified scope and growing complexity in botanical garden research. This study aims to bridge a crucial gap by outlining the developmental trajectory of botanical gardens and offering guidance for future research directions. Diverse research domains within botanical garden studies, including biodiversity, essential oils, taxonomy, and ex-situ conservation, present extensive avenues for exploration. Future research endeavors should delve into these impactful themes to better understand botanical ecosystems and their conservation. The study emphasizes the importance of nurturing interdisciplinary collaborations and multidisciplinary projects, advocating for a comprehensive and collaborative approach to future research in botanical garden studies.

Chemical plants are characterized by the management and operation of various hazardous materials; thus, accident risk is inherently high. Nevertheless, the incidence of chemical accidents in Korea has effectively stabilized, with no marked increase attributable to the implementation of systematic safety management procedures based on process safety management system principles. In June 2023, the Ministry of Employment and Labor in Korea unveiled the Serious Injury and Fatality (SIF) report, meticulously cataloging 4,432 instances of grave accidents spanning six years (2016–2021). The compilation comprises 1,834 and 2,574 cases within the manufacturing and affiliated sectors and the construction sector, respectively. This study provides an overview of each accident, and elucidates the causes, and recommends preventative strategies. The objective was to galvanize companies across various industrial landscapes and fortify their intrinsic safety management protocols by using accident data delineated per sector. Sixteen specific accident cases from the SIF report, all of which occurred in facilities regulated by process safety management (PSM), were investigated. Technical analysis was conducted, focusing on explosion accidents within the organic catalyst packaging process, notable for their unique patterns of occurrence. This analysis extended to an examination of the reproducibility of such accidents. Employing two system analysis methodologies, system theoretic accident model and process and barrier-based systemic cause analysis technique, this study provides insights into the causative factors of the accidents and formulates comprehensive strategies for the prevention of future accidents. The findings will contribute significantly to reducing the risk of accidents within the catalyst packaging domain and assist in the development of robust recurrence prevention measures.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

The experience gained over the last hundred years clearly indicates that two groups of viruses represent the main risk for the development of highly transmissible epidemics and pandemics in the human species: influenza viruses and coronaviruses (CoV). Although the search for viruses with pandemic potential in the environment may have an important predictive and monitoring role, it is still based on empirical methodologies, mostly translated from the clinic and not fully validated for environmental matrices.As far as the SARS-CoV-2 pandemic, currently underway, is concerned, environmental monitoring activities aiming at checking the presence of SARS-CoV-2 in wastewater can be extremely useful to predict and control the diffusion of the disease. For this reason, the present study aims to evaluate the SARS-CoV-2 diffusion by means of a wastewater-based environmental monitoring developed in Piedmont, N-W Italy, during the pandemic second and third waves. Sampling strategies, sampling points, sample pre-treatments and analytical methods have been developed and validated to give representative and reliable results. The outcomes highlighted by the present paper demonstrate a strong correlation between SARS-CoV-2 concentration in untreated wastewater and epidemic evolution in the considered areas as well as a predictive potential that could provide decision-makers with indications for establishing effective policies to mitigate the effects of the ongoing pandemic and to prepare response plans for future pandemics that could certainly arise in the decades to come.Moreover, the study highlights the potential of wastewater treatment plants to degrade the genetic material referable to SARS-CoV-2 as well.In conclusion, the preliminary data reported in the present paper, although they need to be complemented by further studies considering other geographical regions as well, are very promising.

Environmental monitoring plays a central role in diagnosing climate and management impacts on natural and agricultural systems, enhancing the understanding hydrological processes, optimizing the allocation and distribution of water resources, and assessing, forecasting and even preventing natural disasters. Nowadays, most monitoring and data collection systems are based upon a combination of ground-based measurements, manned airborne sensors or satellite observations. These data are utilized in describing both small and large scale processes, but have spatiotemporal constraints inherent to each respective collection system. Bridging the unique spatial and temporal divides that limit current monitoring platforms is key to improving our understanding of environmental systems. In this context, Unmanned Aerial Systems (UAS) have considerable potential to radically evolve environmental monitoring. UAS-mounted sensors offer an extraordinary opportunity to bridge the existing gap between field observations and traditional air- and space-borne remote sensing, by providing not just high spatial detail over relatively large areas in a cost-effective way, but as importantly providing an entirely new capacity for enhanced temporal retrieval. As well as showcasing recent advances in the field, there is also a need to identify and understand the potential limitations of UAS technology. For these platforms to reach their monitoring potential, a wide spectrum of unresolved issues and applications specific challenges require focused community attention. Indeed, to leverage the full potential of UAS-based approaches, sensing technologies, measurement protocols, post-processing techniques, retrieval algorithms and evaluations techniques need to be harmonized. The aim of this paper is to provide a comprehensive general overview of the existing research on studies and applications of UAS in environmental monitoring in order to suggest users and researchers on future research directions, applications, developments and challenges.

The chemical industry is an integral part of the world economy and a substantial income source for developing countries. However, existing regulations or the enforcement of these regulations, on controlling atmospheric pollutants sometimes may be insufficient, leading to the deterioration of surrounding ecosystems and to a quality decrease of the atmospheric environment. Previous works in this domain fail to generate executable solutions for inspection agencies due to practical challenges. In addressing these challenges, we introduce a so-called Chemical Plant Environment Protection Game (CPEP) to generate reasonable schedules of high-accuracy air quality monitoring stations for inspection agencies. First, Stackelberg Security Games (SSGs) are incorporated together with source estimation methods into this research. Second, high-accuracy air quality monitoring stations as well as gas sensors are modeled into the CPEP. Third, simplified data analysis on the regularly discharging of chemical plants is utilized to construct the CPEP. Finally, an illustrative case study is used to investigate the effectiveness of the CPEP Game, and a realistic case study is conducted to illustrate how the models and algorithms being proposed in this paper, work. Results show that playing a CPEP Game can reduce operational costs of high-accuracy air quality monitoring stations; moreover, playing the game leads to more compliance from the chemical plants towards the inspection agencies.

Reducing GHG emissions is a crucial challenge in urban areas, characterized by high energy consumption and reduced exposure to nature. In this context, the urban green system could play a pivotal role. In the literature, scholars analyzed both the ability of species-specific and layout-specific green infrastructures to increase carbon sequestration and the best location sites of new green infrastructures, to increase the provision of overall ecosystem services. There is a lack of studies helping green urban planners and designers choose where and which green infrastructure to implement, based on vegetation species-specific performance and local carbon emissions of city components. This paper uses tree inventory data from a medium-sized city in central Italy (Perugia) to develop a spatial analysis of the urban parks' performance in carbon sequestration. Then, the method evaluates the carbon emission of a public city building to generate a spatialized balance between buildings’ demand and trees’ supply, to support local decisions about the best locations for new green infrastructures and the choice between species. The paper contributes to GIS-based tools that vary the recommended location sites and species for new green infrastructures based on the demanded ecosystem service.

Rebar cages form the skeletal framework of reinforced concrete structural members. They comprise longitudinal and transverse reinforcing bars, usually connected by tie wires. Past studies have identified tie-wire connections as the "weak links" in large, prefabricated rebar cages, leading to their failure during site handling and construction stages. Recent research has explored the use of mechanical U-bolt connectors to bolster stability and safety of rebar cages while reducing their vulnerability and risk of failure. This paper presents a comprehensive experimental and numerical investigation of a new type of mechanical connector, referred to as "Cage Clamp", to enhance rebar cage stability and safety. Component-level experimental tests are conducted to determine the force-displacement response of Cage Clamp connectors for crossbar connections in different degrees of freedom. The results highlight the remarkable strength and stiffness of Cage Clamp connectors, significantly outperforming traditional tie-wire connections. Furthermore, full-scale experimental tests are performed on a circular underground pile-shaft rebar cage with Cage Clamp connectors to assess its behavior under various site handling conditions. The data obtained from these experiments are used to construct and refine detailed 3D finite element models of the rebar cages, capable of capturing the complex behavior of rebar cages with Cage Clamp connectors. Using the numerical model, a sensitivity analysis is performed to assess the effect of the number of Cage Clamps on the deflection and stability of the rebar cage. The findings show that using cage clamps to connect pick-up rebar with lateral reinforcement at every 8 to 10 feet is sufficient to ensure the stability of the cage during typical site handling conditions. The results of this study serve as a basis for establishing analysis, design, fabrication, and handling guidelines for rebar cages, contributing to safe and efficient construction practices.

Pollution, urbanization and technological advancements have posed stress on the ecosystem and its matrices. Globally, pollutants are observed in all compartments of ecological communities which affect the integrity of the atmosphere, hydrosphere, lithosphere and biosphere. Xenobiotics bioaccumulate and biomagnify across trophic levels or webs. Heavy metals have been implicated in impacts towards biodiversity and environmental declination. In Nigeria, wastes issues are a cause of concern and landfilling or are waste disposal approaches that cause deleterious effects such as depauperation of diversity and species decline, prompting the non-invasive ecotoxicological hazard assessments. Feathers were used to assess concentration levels of 13 metals (Fe, Mn, Zn, Cu, Co, Cr, Cd, Pb, Ni, Al, B, Se and Hg) using fast atomic absorption spectrophotometer (FAAS), one-way ANOVA was used in comparing variations in mean concentrations across trophic levels, diversity indices and point count methods were used to estimate diversity and abundance. Four avian species were assessed Hirundo aethiopica (insectivore), Streptoptelia senegalensis (granivore), Turdus pelios (omnivore), and Anthus leucophrys. (insectivore). Observed concentrations of important metals like iron were high with the insectivores having the highest concentrations of iron (2.6985 ± 0.1975 ppm) and granivores having the lowest (2.0100 ± 0.3172 ppm). The insectivores had the highest concentrations for cadmium, cobalt and chromium (0.0005 ± 0.0005ppm), nickel (at 00.0012 ± 0.0017 ppm) and least was observed in the granivores (0.0003 ± 0.0006 ppm). Selenium concentrations were quite high in insectivores (0.0775 ± 0.0035 ppm) and lowest in granivores (0.0433 ± 0.0015 ppm) likewise mercury for insectivores (0.0280 ± 0.0010 ppm) and granivores (0.0213 ± 0.0015 ppm). From the study, it is apparent that landfills are sources of pollution and poor management of wastes can affect biota (causing effects such as asymmetry and bioaccumulation) and ecosystem balance. The observation of heavy metals in the feathers serve as good sentinels due to their trophic levels and could be signs for what could be yet to occur. The heavy metal concentrations were significantly different at p < 0.05.

Dye/salt separation has gained increasing attention in recent years, prompting the quest for cost-effective and environmentally-friendly raw materials for synthesis high performance nanofiltration (NF) membrane for effective dye/salt separation. Herein, a high-performance loose structured NF membrane was fabricated by via a simple vacuum filtration method using a green nanomaterial, 2,2,6,6-tetramethylpiperidine-1-oxide radical (TEMPO)-oxidized cellulose nanofiber (TOCNF), by sequentially filtrating larger-size and finer-size TOCNFs on a microporous substrate, followed by cross-linked with trimesoyl chloride. The resultant TCM membrane possesses a separating layer composed entirely of pure TOCNF, eliminating the need for other polymer or nanomaterials additives. TCM membranes exhibits high performance and effective dye/salt selectivity. Scanning Electron Microscope (SEM) analysis shows that the TCM membrane with Fine-TOCNF layer has a tight layered structure. Further characterizations via Fourier transform infrared spectroscopy (FTIR) and X-ray diffraction (XRD) confirm the presence of functional groups and chemical bonds of the crosslinked membrane. Notably, the optimized TCM-5 membrane exhibits a rejection rate of over 99% for various dyes (Congo red, orange yellow) and 14.2% for NaCl, showcasing a potential candidate for efficient dye wastewater treatment.

The yeast Saccharomyces cerevisiae ensures successful fermentation in winemaking, although the persistent use of commercial strains lead the loss of aroma complexity of wines. Hence, the research of indigenous S. cerevisiae with proper oenological features and well adapted to specific wine-growing area become of great interest for winemakers. Here, 206 S. cerevisiae strains were isolated from two wineries during two-year sampling campaign and bio-typed with the aim to evaluate the occurrence and persistence of S. cerevisiae wild population linked to each winery. Both wineries belonging to the same Verdicchio DOC wine area (Castelli di Jesi), and never used commercial yeasts during fermentation. Results showed a specific and varied population of S. cerevisiae in each winery without cross-contamination each other and with commercial starter strains. Moreover, inside each winery it was observed a persistent of some dominant biotypes over the time, indicating a sort of “winery-effect”. The evaluation of S. cerevisiae populations for the oenological characters showed a proper and well distinct aromatic imprinting on the resulted wines confirming the “winery effect”.

Quantitative analysis of human gait is critical for early discovery, progressive tracking, and rehabilitation of neurological and musculoskeletal disorders, such as Parkinson’s Disease, stroke, and Cerebral Palsy. Gait analysis typically involves estimating gait characteristics, such as spatio-temporal gait parameters and gait health indicators (e.g., step time, length, symmetry, and balance). Traditional methods of gait analysis involve the use of cameras, wearables, and force plates, but are limited in operational requirements when applied in daily life - such as direct line-of-sight, carrying devices, and dense deployment. This paper introduces a novel approach for gait analysis by passively sensing footstep-induced floor vibrations during walking using vibration sensors mounted on the floor surface. Our approach is non-intrusive, scalable, and perceived as more privacy-friendly, making it suitable for continuous gait health monitoring in daily life. We developed a floor vibration-based gait analysis framework to estimate various gait parameters that are used as standard metrics in medical practices, including temporal parameters (step, stride, stance, swing, double-support, single-support time) and spatial parameters (step length, width, angle, stride length), and extracts gait health indicators (cadence/walking speed, left-right symmetry, gait balance, initial contact types). The main challenge is that floor vibrations are distinct across different floor types. To address this challenge, our approach develops floor-adaptive algorithms to extract floor-specific features and is designed to be generalizable to various settings, including homes, hospitals, and eldercare facilities. We evaluate our approach through real-world walking experiments with 20 adults with 12,231 labeled gait cycles across concrete and wooden floors. Our results show 90.5% (RMSE 0.08s), 71.3% (RMSE 0.38m), and 92.3% (RMSPE 7.7%) accuracy in estimating temporal, spatial parameters, and gait health indicators, respectively.

Background: This study attempted to construct musculoskeletal JEM using KWCS data and use it to evaluate the burden of these disorders in Korean workers. Methods: This study was conducted using data from the second to the sixth KWCS, and a total of 210,500 people were included. The jobs of the subjects were reclassified based on the unit groups of the 7th Korean Standard Classification of Occupation (KSCO). The intensity of exposure to work-related risk factors for musculoskeletal disorders was classified into ‘high’, ‘moderate’, and ‘low’ for the body segments involving the ‘upper extremities and neck’, ‘lower back’, and ‘lower extremities’. Results: The time of exposure was longest in the standing posture and repetitive hand and arm movements. An analysis of the intensity of exposure by body segments revealed that the highest intensity of exposure was to the upper extremities. For the upper extremities and neck, and the lower back, there was a exposure-response relationship in the association between intensity of exposure and musculoskeletal symptoms. However, for the lower extremities, there was a exposure-response relationship only at high exposure. Conclusion: In this study, a JEM for work-related risk factors for musculoskeletal disorders was constructed for the first time in Korea. The intensity of exposure to musculoskeletal risk factors was estimated for each occupation. The JEM constructed in this study is expected to have high applicability for assessing the risk of musculoskeletal disorders for each job with respect to the upper extremities and neck, and lower back.

Extreme climates such as droughts and hot extremes, may result in marked damage to crop yields and threaten regional and global food security. Maize is a major grain crop in Liaoning Province, severely affected by drought and hot events. The objective of this study is to advance an approach to estimate the risk of crop yield reduction under the compound dry-hot events (CDHE) in Liaoning Province. Results show that the ratio of stations experiencing compound dry-hot events during the twelfth leaf and maturity stage tended to increase on the time scale. On a spatial scale, the frequency of compound dry-hot events in central Liaoning Province was relatively low during the whole and various reproductive periods of maize. In addition to the twelfth leaf, western Liaoning Province is prone to compound dry-hot events. The high-risk area for the occurrence of the compound dry-hot events in maize is Chaoyang City, located in the western part of Liaoning Province, and the cities in the low-risk area account for about 64.3% of the total number of cities in Liaoning Province, mainly in the central and northern parts of Liaoning Province. Generally, this study emphasizes focusing on the impacts of compound dry-hot events on agricultural production and provides an index to assess the risk of compound dry-hot events on maize production.

Umbria is an Italian region with a highly fragmented water supply, with many small water distribution systems fed by local sources. The chlorination in these small water systems faces many difficulties related to the high demand variation, low economic relevance, and access to infrastructures. As a result, there are many noncompliances with the quality of the supplied water, which causes a decrease in the performance indicators and tariff. This research investigates the possibility of using a low-cost chlorination system to consider different environmental conditions (e.g., temperature variations of water and environment, pH, ...) and discontinuous consumption. A device for this specific use is developed and tested by laboratory tests and is ready for use in the field.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Urban air pollution is a critical global environmental issue, necessitating an understanding of the spatiotemporal characteristics and driving factors for effective environmental protection and urban planning. This study introduced an advanced air quality assessment system that integrates environmental, socio-economic, and urban layout factors, addressing gaps in traditional models that often overlook the impact of urban spatial structures. Analyzing air quality data from Beijing's main urban area (2016-2020) alongside multi-source geographic data, the research develops a comprehensive evaluation system, incorporating 14 key driving factors. Employing Geographically Weighted Regression (GWR) and Multi-scale Geographically Weighted Regression (MGWR), the study quantitatively assessed the influence and spatial heterogeneity of these factors. Findings revealed an annual improvement in air quality, with a U-shaped seasonal pattern and significant spatial clustering (Global Moran’s I = 0.922). The MGWR model, in particular, provided a superior fit over GWR, effectively capturing the spatial variability of factors. Variables such as NDVI), economic output (GDP), and humidity space adjustment capability (HSAC) showed significant positive spatial impacts on air quality, while population density (POP), temperature (TEMP), and road density (RD) exhibited negative effects. These insights enhance the understanding of air pollution dynamics and aid in refining urban planning strategies.

Facing global warming consequences is a major issue of present times. For what concerns climate, projections say that heavy rainfalls are going to increase with high probability together with temperature rise, thus also the hazard related to rainfall induced shallow landslides will likely increase in density over susceptible territories. Different modeling approaches exist and any of them is forced to make simplifications in order to reproduce landslide occurrences over space and time. Process based models can help in quantifying the consequences of heavy rainfall on the different involved processes. In this paper, a narrative review about physically-based deterministic distributed models (PBDDMs) is presented. Models were selected based on: the adoption of the infinite slope scheme (ISS), the use of a deterministic approach (i.e., input and output are treated as absolute values), the inclusion of new approaches in modeling slope stability through the ISS. Models are presented in chronological order with the aim of drawing a timeline of the evolution of PBDDMs and to give researchers and practitioners a basic knowledge on how much has been already done. Results indicate that including vegetation effects on slope stability has raised in importance over time but that there is still the need of finding an efficient way to include them, and that in the last years the literature production seems to be more focused on probabilistic approaches.

With increasing power and speed of laser welding, in-process monitoring has become even more crucial to ensure process stability and weld quality. Due to its low cost and installation flexibility, acoustic process monitoring is a promising method and has demonstrated its effectiveness. Since its feasibility has been the focus of existing studies, the temporal resolution of acoustic emissions (AE) has not yet been addressed despite its utmost importance for realizing real-time systems. Aiming to provide a benchmark for further development, this study investigates the relationship between duration and informativeness of AE signals during high power (3.5kW) and high speed (12m/min) laser beam butt welding. Specifically, the informativeness of AE signals is evaluated based on the accuracy of detecting and quantifying joint gaps for various time windows of signals, yielding numerical comparison. The obtained results show that signals can be shortened up to a certain point without sacrificing their informativeness, encouraging to optimize the signal duration. Our results also suggest that large gaps (> 0.3mm) induce unique signal characteristics in AE, which are clearly identifiable from 1 ms signal segments, equivalent to 0.2mm weld seam.

Marine sand, in addition to oil and gas resources, is the second largest marine mineral resource. The rational development and utilization of marine sand resources are conducive to the growth of the marine economy. Marine sand can be categorized into surface marine sand and buried marine sand. Buried marine sand deposits are buried beneath the sea floor, making it challenging to locate them due to their thin distribution. Consequently, there exist numerous technical difficulties associated with marine sand exploration. In this study, various geophysical methods such as sub-bottom profile survey and single-channel seismic survey were employed in the northern offshore waters of the South China Sea along with offshore engineering geological drilling. As a result, two distinct marine sand bodies were delineated within the study area. Additionally, five reflective interfaces (R0, R1, R2, R3 and R4) were identified from top to bottom. These interfaces can be divided into five seismic sequences: A2, B2, C2, D2 and E2 respectively. Three sets of strata were recognized: the Quaternary Holocene Marine sedimentary layer (Q4m), the Upper Pleistocene alluvial layer, and the diluvial sedimentary layer (Q3al+pl) as well as the Upper Pleistocene Marine sedimentary layer (Q3m). Sequence A2 and B2 corresponded to Quaternary Holocene Formation (Q4m) within the study area while sequence C2 corresponded to B2 as well as upper Pleistocene alluvial and alluvial deposits (Q3al+pl), which represent one of the main occurring layers of sand in this region. Lastly, E2 represents a layer composed mainly of silty clay and round gravel known as upper Pleistocene marine sediment layer (Q3m). In total, two ore bodies containing marine sand have been discovered during this study. The estimated total resource amounts approximately 46 million m³ with an average thickness around 11 meters.

It has remained a hard nut for years to segment sonar images, most of which are noisy images with inevitable blur after noise reduction. For the purpose of solutions to this problem, a fast segmentation algorithm is proposed on the basis of the gray value characteristics of sonar images. This algorithm is endowed with the advantage in no need of segmentation thresholds to be calculated. To realize this goal, it follows the undermentioned steps: first, calculate the gray matrix of the fuzzy image background. After adjusting the gray value, segment the region into the background region, buffer region and target regions. After filtering, reset the pixels with gray value lower than 255 to binarize images and eliminate most artifacts. Finally, remove the remaining noise from images by means of morphological image processing. The simulation results of several sonar images show that the algorithm can segment the fuzzy sonar image quickly and effectively, with no problem of incomplete image target shape. Thus, the stable and feasible method is testified.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

Climate change presents an urgent global challenge, manifesting in rising temperatures and extreme weather events with severe societal impacts. The Eastern Mediterranean, warming faster than the global average, faces immediate repercussions. Climate literacy emerges as pivotal, empowering individuals to comprehend climate science and act accordingly. This study delves into climate literacy, attitudes, and 'greening' behaviours in the Eastern Mediterranean hotspot of Greece, based on a survey of 1,962 citizens. Findings indicate high climate literacy but lower adoption of 'greening' behaviours, especially those involving financial costs. Regression analyses highlight the significant role of climate literacy, concerns about personal impacts, coping appraisal and trust in institutions in promoting 'greening' behaviours. The study underscores the need for multifaceted strategies emphasizing financial motivation, trust-building, and societal norm shifts. Socio-demographic disparities, including gender and occupation, highlight areas for targeted interventions. The emphasis on the mental health impacts of climate-related events underscores the need for holistic disaster management. Policy implications are discussed, highlighting the potential of expanded climate literacy to catalyze collective action toward sustainability.

Forest ecosystems make a greater contribution to carbon (C) stocks than any other terrestrial ecosystem. To understand the role of regional forest ecosystems in global climate change and carbon exchange, forest C stock and its spatial distribution within the small (2,300 km2) Liuxihe River basin were analyzed to determine the different contributors to the C stock. Forest C stocks were quantified by measuring the biomass of trees, understory vegetation, litter and roots, as well as soil organic C, using data from field samples and laboratory experiments. The results showed that forests stored 38.04 Tg C in the entire basin, with secondary and planted forests accounting for 89.82% and 10.18%, respectively, of the stored C. Five types of forests, a subtropical evergreen broad-leaved forest, a subtropical coniferous and broad-leaved mixed forest, a subtropical coniferous forest, a timber forest, and a non-wood forest, stored 257.55 ± 15.01, 218.92 ± 9.59, 195.24 ± 18.29, 177.42 ± 17.55, and 117.86 ± 6.04 Mg C ha−1, respectively. In the forest ecosystem C stocks of the basin, soils averagely contribute about 73.78%, not including root underground biomass. It provides a comprehensive method for forest ecosystem carbon investigation and forest management in small basin scale.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

The Asian clam Corbicula fluminea is a native aquatic species in Eastern Asia and Africa but has become one of the most ecologically and economically harmful invasive species in aquatic ecosystems in Europe, North America, South America. Due to their natural characteristics as a hermaphroditic species with high fecundity and dispersal capacity, Asian clams are extremely difficult to eradicate once they have infiltrated a waterbody. This is an emerging issue for states in the Northeastern United States as Asian clams expand their range farther North due to climate change. There has been extensive research conducted to develop chemical treatments to reactively control invasive mollusc populations and proactively prevent their further spread. However, treatments are mostly targeted toward biofouling bivalves in industrial settings. A comprehensive review of Asian clam chemical treatments used in open water systems was performed to evaluate molluscicides and identify toxicity ranges of emerging treatments that maximize Asian clam mortality and minimize negative impact to water quality and non-target species. The potential chemical applications in Asian clam control and management are summarized in this report to assist resource managers and practitioners on invasive Asian clam management.

In this paper, we study the well-posedness and asymptotics of a one-dimensional thermoelastic laminated beam system either with or without structural damping, where the heat conduction is given by Fourier's law effective in the rotation angle displacements. We show that the system is well-posed by using Lumer-Philips theorem, and prove that the system is exponentially stable if and only if the wave speeds are equal, by using the perturbed energy method and Gearhart-Herbst-Prüss-Huang theorem. Furthermore, we show that the system with structural damping is polynomially stable provided that the wave speeds are not equal, by using the second-order energy method.

In Belgium, sex work was recently decriminalized to enhance street-based sex workers’ (SSWs) health. This qualitative study explores stakeholders' perceptions of the impact of the working environment on street-based sex workers’ occupational safety, health and well-being in Brussels. In-depth interviews with seven stakeholders directly involved with SSWs were conducted with data analyzed using qualitative content analysis. The analysis of study data resulted in one theme: “A power imbalance and a lack of concerted efforts among stakeholders are detrimental to the occupational safety, health, and well-being of street-based sex workers”. In Brussels, the majority of SSWs face various challenges due to structural vulnerabilities, thus limiting their choices regarding their work environment, and further compromising their health. Limited access to resources and severe constraints within their working environment contribute to a lack of safety and adverse health outcomes. A stigma mechanism fueled by ideology and personal interests prevent the enforcement of their rights regarding their working environment, safety and health promotion. The lack of involvement of key stakeholders, especially from the public sector, prevents the majority of SSWs in Brussels from benefiting from a sound working environment and the promotion of their health, safety and well-being.

The paper presents two procedures for creating 3D discrete models of apple using the finite element method (FEM). The study focused on a new Polish apple variety, Chopin at development, ripening, and senescence maturity stages. The analysis of the results allowed for the determination that, depending on the desired outcomes, the parenchymal tissue can be considered as a material with either elastic or elastoplastic properties. Model validation was performed using displacement-force relationships and changes in contact area as a function of loading force obtained from compression tests. Elastoplastic models reflect empirical studies much better. The fit of the elastic models, based on force vs. displacement curves, ranged from 79% to 83%, while the fit of the elastoplastic models to empirical data ranged from 91% to 96%. Elastic models, on the other hand, are well-suited to the modified force vs. displacement curves, which reflect the elastic behavior of apples under compression test. Contour plots of pressures for elastoplastic models align much better with the test results than those for elastic models. 4. Similarly, in the case of contact area values, the elastoplastic models outperformed the elastic models, achieving a fit between 92% and 96%, while the elastic models reached only 82% to 83% compliance.

Most available studies on the mechanical properties of apples lack the comprehensive results needed for the construction and validation of FEM models. Researchers typically focus on either the flesh and epidermis or the whole fruit, often overlooking the maturity stage of the examined apples. They usually report only firmness or the starch index as indicators of maturity. Furthermore, many studies use store-bought apples, which is impractical for industrial applications since this fruit have already undergone various treatments before reaching the shelf. This article aims to determine the mechanical properties of apples necessary for constructing FEM models that are both adequate and useful for the industry. The new Polish apple variety, Chopin, was selected as the research material. The study was conducted for three stages of apple maturity: development, ripening, and senescence. Mechanical properties of the flesh and skin were determined as material data for FEM models. Force-displacement curves and pressure-force functions were examined for future model validation. Using micro-computed tomography, the bruise volumes of fruit subjected to 20%, 50%, and 80% of the destructive force were determined. Significant differences were found between apples in the senescence stage and those in the development and ripening stages. Results of Micro-Ct and the results of modified and real compression tests of whole fruit have allowed us to formulate the research hypothesis regarding the influence of flesh cracking (characterized by local drops of force), influencing the bruise visibility and detection.

Microcystis-dominated cyanobacterial blooms (MCBs) frequently occur in freshwaters worldwide due to massive Microcystis colonies formation and severely threaten human and ecosystems health. Quorum sensing (QS) is a direct cause of Microcystis colonies formation, possibly regulating MCBs occur and Microcystis population behaviors [1, 2]. Many novel findings in fundamental knowledge of Microcystis QS phenomenon and the signaling molecules have been documented. However, little effort has devoted to comprehensively summarize and discuss research progresses and exploration direction on QS signaling molecules-mediated QS system in Microcystis. This article summarizes action process of N-acyl homoserine lactones (AHLs) as major signaling molecules in Microcystis and discussed the detailed roles of AHLs-mediated QS system in cells aggregation, colonies formation, ecological adaptability and competitive advantage. And the progress was summarized in research on the QS mechanism in Microcystis. Compared to other QS system, the LuxI/LuxR-type QS system is more likely to found in Microcystis. Also, we introduced Quorum quenching (QQ) — QS blocking process in Microcystis, with emphasizing on the potential of QS inhibitors in MCBs control. Finally, in response to the research deficiencies and gaps in Microcystis QS and QQ, we proposed several future research directions in these fields. This review may deepen the understanding of Microcystis QS knowledge and provide theoretical guidance for the development of strategies to monitor, control and harness MCBs.

Extensive green roofs provide for many ecosystem services in urban environments. The efficacy of these services is influenced by the substrate characteristics and vegetational composition. Despite their key role in plant performance and productivity, or their contribution to nitrogen fixation or carbon sequestration, green roof microbial communities have received little attention so far. Here, we investigated whether microbial communities in extensive green roof substrates contain a core community, as well as whether they are affected by green roof plant diversity. Eleven green roofs, planted either with a mixture of grasses, wildflowers and succulents (Sedum spp.), or solely species of Sedum, were seasonally sampled to investigate prokaryotic and fungal communities via metabarcoding. Although Sedum-herbs-grasses roofs contained more plant species, we observed no discriminant microbial communities between both roof types, likely due to sharing the same substrate textures and the vegetational layers that became more similar throughout time. Examining key microbial taxa revealed that most taxa are also dominant phylotypes in soils across different biomes. Many bacterial core taxa are capable of nitrogen fixation and most fungal key taxa are stress-tolerant saprotrophs, endophytes, or both. Microbial community composition further revealed high similarities with aerial samples taken in urban environments. Considering the extreme edaphic conditions that periodically arise in green roof substrates, further investigation is warranted to determine the extent to which the dynamic and intriguing microbial communities are influenced by the aeromicrobiome.

As split learning (SL) becomes popular for addressing data privacy and resource limitation issues in edge model training process, it is crucial to pre-validate whether the extensive use of wireless and computing resources in SL can achieve the expected training latency and convergence. While digital twin network (DTN) can potentially estimate network strategy performance in pre-validation environments, they are still in their infancy for SL tasks, facing challenges like unknown non-i.i.d. data distributions, inaccurate channel states, and misreport resource availability across devices. To address these challenges, this paper proposes a TransNeural algorithm for DTN pre-validation environment to estimate SL latency and convergence. First, the TransNeural algorithm integrates transformers to efficiently model data similarities between different devices, considering different data distributions and device participate sequence greatly influence SL training convergence. Second, it leverages neural network to automatically establish the complex relationships between SL latency and convergence with data distributions, wireless and computing resources, dataset sizes, and training iterations. Deviations in user reports are also accounted for in the estimation process. Simulations show that the TransNeural algorithm improves latency estimation accuracy by 13.44% and convergence estimation accuracy by 116.74% compared to traditional equation-based methods.

Biodiversity has become an issue of global anxiety over the past decades due to its rapid decline worldwide. Bangladesh as one of the most densely populated countries in the world is no more exception. The country, although, was once very rich in biodiversity, during the last few decades as a consequence of the rapid reduction in forest area, urbanisation, habitat modification, unsustainable natural resources use and collection and overall climate change it has decreased alarmingly. Of late, the government, as a signatory of various regional and international conservation treaties, has taken various initiatives to improve country’s dwindling biodiversity. This paper reviews the present situation of biodiversity in Bangladesh, management trends and major causes of biodiversity loss. A separate statutory body is fundamental to ensure conservation, sustainable use and equitable sharing of benefits arisen from biodiversity in the country.

Computational models of homologous protein groups are essential in sequence bioinformatics. Due to the diversity and rapid evolution of viruses, the grouping of protein sequences from virus genomes is particularly challenging. The low sequence similarities of homologous genes in viruses require specific approaches for sequence- and structure-based clustering. Furthermore, the annotation of virus genomes in public databases is not as consistent and up-to-date as for many cellular genomes. To tackle these problems, we have developed VOGDB, a database of Virus Orthologous Groups. VOGDB is a multi-layer database that progressively groups viral genes into groups connected by increasingly remote homology. The first layer is based on pair-wise sequence similarities, the second layer is based on the sequence profile alignments and the third layer uses predicted protein structures to find the most remote homology. VOGDB groups allow for more sensitive homology searches of novel genes and increase the chance of predicting annotations or inferring phylogeny. VOGDB uses all virus genomes from RefSeq and partially re-annotates them. VOGDB is updated with every RefSeq release. The unique feature of VOGDB is inclusion of both prokaryotic and eukaryotic viruses in the same clustering process which makes it possible to explore old evolutionary relationships of the two groups. VOGDB is freely available at https://vogdb.org under the CC BY 4.0 license.

Photocatalysis is a promising method for methylene blue (MB) degradation due to its effectiveness and environmental compatibility. Among photocatalysts, titanium dioxide (TiO2) has been widely used for MB degradation due to its exceptional photocatalytic activity. However, the wide bandgap limits the degradation efficiency of TiO2 under visible light. Herein, an interstitial nitrogen-doped TiO2 (5%NT/TiO2) used thiourea as the N source is fabricated for the visible light-derived MB degradation. 5%NT/TiO2 exhibits an extended visible light absorption range. Besides, photoelectrochemical measurement shows an improvement in photocurrent response and charge transfer behavior on N/TiO2. Thus, 5%NT/TiO2 has enhanced photocatalytic activity compared to pristine TiO2 and substitutive N-doped TiO2 (5%NAB/TiO2). The accelerated photocatalytic MB degradation process on N/TiO2 should be mainly attributed to the interstitial N doping, which causes the appearance of new energy states and extended optical properties.

The term Conjugated Linoleic Acid (CLA) refers generically to a class of positional and geometric conjugated dienoic isomers of linoleic acid. Among the isomers of linoleic acid cis9, trans11-CLA (c9, t11-CLA) and trans10, cis12-CLA (t10, c12-CLA) are found to be bio-logically active isomers, and they occur naturally in milk, dairy products and meat from ruminants. In addition, some vegetables and some sea-foods have also been reported to contain CLA. Although the CLA levels in these natural sources are insufficient to confer the essential health benefits, anti-carcinogenic or anti-cancer effects are of current interest. In the rumen, CLA is an intermediate of isomerization and the biohydrogenation process of linoleic acid to stearic acid conducted by ruminal microorganisms. In addition to rumen bacteria, some other bacteria, such as Propionibacterium, Bifidobacterium and some lactic acid bacteria (LAB) are also capable of producing CLA. In this regard, Lactiplantibacillus plantarum (formerly Lactobacillus plantarum) has demon-strated the ability to produce CLA isomers from linoleic acid by multiple enzymatic activi-ties, including hydration, dehydration, and isomerization. L. plantarum is one of the most versatile species of LAB and the bacterium is widely used in the food industry as a micro-bial food culture. The studies reviewed in this article reveal how, in the production of some fermented foods, the use of appropriate strains of L. plantarum, as a starter or additional culture, can be considered a critical factor in the design of new CLA-enriched functional foods.

This study aimed to explore the feasibility of using airborne acoustic emission in laser beam butt welding for the development of an automated classification system based on neural networks. The focus was on monitoring the formation of joint gaps during the welding process. To simulate various sizes of butt joint gaps, controlled welding experiments were conducted, and the emitted acoustic signals were captured using audible to ultrasonic microphones. To implement an automated monitoring system, a method based on short-time Fourier transformation was developed to extract audio features, and a convolutional neural network architecture with data augmentation was utilized. The results demonstrated that this non-destructive and non-invasive approach was highly effective in detecting joint gap formations, achieving an accuracy of 98%. Furthermore, the system exhibited promising potential for low latency monitoring of the welding process. The classification accuracy for various gap sizes reached up to 90%, providing valuable insights for characterizing and categorizing joint gaps accurately. Additionally, increasing the quantity of training data with quality annotations could potentially improve the classifier model's performance further. This suggests that there is room for future enhancements in the study.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

The utilization of primary school buildings is multifaceted, primarily due to the high occupancy density, varying thermal preferences among occupants, diverse indoor activities (such as walking, sports, and conversation), and a constant flow of individuals entering and exiting the building. This results in frequent opening and closing of external windows and doors and fluctuations in internal heat gain. Consequently, frequent interactions between the indoor and outdoor microenvironments lead to energy losses. This study conducts a comprehensive literature review on building energy loss stemming from occupant behavior and the interactions between indoor and outdoor microenvironments. Furthermore, it proposes a dynamic real-time monitoring system based on a computer data capture and visualization platform foundation for building energy loss. The research methods include data crawling, data association rule mining, and data association analysis. The research findings yield a universally applicable and informative building energy-saving design theory based on extensive data analysis. Additionally, the system presents information on occupants' behavior and the microclimate data of indoor and outdoor environments on a computer screen, facilitating human-machine communication and enabling timely adjustments to design strategies for new buildings and operation and maintenance strategies for existing buildings.

This study investigated the effects of fish oil (FO) treatment, particularly enriched with eicosapentaenoic acid (EPA), on obesity induced by a high-fat diet (HFD) in mice. The investigation focused on elucidating the impact of FO on epigenetic modifications in white adipose tissue (WAT) and the involvement of adipose-derived stem cells (ASCs). C57BL/6j mice were submitted to a control diet or a HFD for 16 weeks, treated (or not) with FO for the last 8 weeks. WAT was removed for RNA and protein extraction, while ASCs were isolated, cultured, and treated with Leptin. All samples were analyzed using functional genomics tools, including PCR-array, RT-PCR and Western Blot assays. Mice receiving HFD displayed increased body mass, fat accumulation, and altered gene expression associated with WAT inflammation and dysfunction. FO supplementation attenuated these effects, a potential protective role against HFD-induced obesity. Analysis of H3K27 revealed HFD-induced changes in histone, which were partially reversed by FO treatment. The study further explored leptin signaling in ASCs, suggesting a potential mechanism for ASC dysfunction in the leptin-rich environment of obese WAT. Overall, FO supplementation demonstrated efficacy in mitigating HFD-induced obesity, influencing epigenetic and molecular pathways, and shedding light on the role of ASCs and leptin signaling in WAT dysfunction associated with obesity.

One of the most important agrotechnical factors that influence the growth conditions of crops is plant density. Alterations in habitat conditions result in the emergence of phytophagous organisms, whose development is closely associated with host plants. The objective of this study was to assess the abundance and species composition of thrips (Thysanoptera) collected in soybean plants of different varieties cultivated under different plant arrangements (row spacing, number of seeds sown differed). The research was conducted at two locations in southwestern Poland between 2015 and 2018. The herbivores that inhabit plants were caught using an entomological net. The experiments were carried out using the complete randomised block design, with four replications. Regardless of location and treatment, thrips were the most numerous group of pests. Thrips tabaci and T. fuscipes were the dominant species within the collected material. A total of 24 species of thrips were identified and their dietary specialisation was determined. The assemblages of studied insects were also analysed due to the density of the plants and the stage of development. The increase in the sowing density of soybean (90 seeds per m2) resulted in a greater total number of thrips compared to a lower sowing density (50 seeds per m2). The number of thrips significantly increased during the flowering period and shortly after the flowering time, which made them a significant threat to the plants. Therefore, it is crucial to develop innovative pest management strategies tailored to effectively grow soybean to mitigate potential pest-related challenges.

The global usage of veterinary antibiotics is significant. These antibiotics can be released into the aquatic environment and exert toxic effects on non-target organisms. To explore the physiological effects of tetracycline antibiotics on aquatic life, the growth characteristics of and toxin release from the cyanobacterium Microcystis aeruginosa (M. aeruginosa) were studied. Results showed that the toxicity order of the three target antibiotics was TC (tetracycline) > CTC (chlortetracycline hydrochloride) > OTC (oxytetracycline) in terms of inhibition occurrence time and the EC₁₀ and EC₂₅ values. Further, the target antibiotics regulated the production of MC-LR (microcystin-LR) to different degrees. CTC destroyed the M. aeruginosa cells and resulted in a decreased MC-LR release but stimulated the ability to synthesise MC-LR. OTC had a relatively weaker toxicity compared with CTC, while TC was the most toxic among the three antibiotics. Therefore, TC is friendly to the aquatic environment because it simultaneously reduced the intracellular and extracellular MC-LR content. These results aid our understanding of the effects of tetracycline antibiotics on Microcystis aeruginosa, which is important for environmental evaluation and protection. These results are also helpful for guiding the application of veterinary antibiotics in agricultural settings.

In the last decade, the application of non-Saccharomyces yeasts in oenology as a natural tool to obtain wine diversification and higher quality has aroused great interest. In this work, three M. pulcherrima strains, isolated from vineyard, were characterized through the evaluation of their main technological properties, antimicrobial activity and specific enzymatic activities (β-glucosidase, β-lyase, polygalacturonase and protease). The M. pulcherrima strains did not produce any inhibition against S. cerevisiae, while they were able to exert an antimicrobial action against some unwanted bacteria and yeasts frequently present in grape must and potentially causing alteration of wines. After this preliminary screening, M. pulcherrima AS3C1 has been selected to be used in the winemaking of red grape Vitis vinifera cv. Aglianico on a pilot scale. The effect of sequential inoculation of M. pulcherrima AS3C1 with a commercial strain of Saccharomyces cerevisiae was verified using for comparison a single inoculum with S. cerevisiae and a spontaneous fermentation. Our results showed a higher concentration of anthocyanins and catechins in wines obtained by sequential inoculation of M. pulcherrima AS3C1 and S. cerevisiae. On the basis of the data obtained, M. pulcherrima AS3C1 possesses an enzymatic profile and some oenological properties that could contribute positively to the definition of the chemical composition of wines, suggesting its possible use for red winemaking processes.

Of the 100,000 railroad bridges in the United States, 50% are over 100 years old. Many of these bridges do not meet the minimum vertical clearance standards, making them susceptible to impacts from over-height vehicles. Impacts can cause structural damage and unwanted disruption to railroad bridge services; rapid notification of the railroad authorities is crucial to ensure that the bridges are safe for continued use and to affect timely repairs. Therefore, researchers have developed approaches to identify these impacts to railroad bridges. Some recent approaches use machine learning to more effectively identify impacts from the sensor data. Typically, the collected sensor data is transmitted to a central location for processing. However, the challenge with this centralized approach is that the transfer of data to a central location can take considerable time, which is undesirable for time-sensitive events like impact detection that require rapid assessment and response to potential damage. To address the challenges posed by the centralized approach, this study develops a framework for edge implementation of machine learning predictions on wireless smart sensors. Wireless sensors are used because of their ease of installation and lower costs compared to their wired counterparts. The framework is implemented on the Xnode wireless smart sensor platform, thus bringing artificial intelligence models directly to the sensor nodes and eliminating the need to transfer data to a central location for processing. This framework is demonstrated using data obtained from events on a railroad bridge near Chicago; results illustrate the efficacy of the proposed edge computing framework for such time-sensitive structural health monitoring applications.