This paper illustrates an experimental activity for the closed-loop position control of an actuator made using shape memory alloy (SMA) wire. A solution with the self-sensing effect was implemented to miniaturize the systems, i.e., without external sensors. A proportional control algorithm was initially used, demonstrating the idea's feasibility: the wire can behave simultaneously as an actuator and sensor. An experimental investigation was subsequently conducted for the optimization of the developed actuator. As for the material, a Flexinol wire, Ni-Ti alloy, with a diameter of 0.150 mm and a length of 200 mm, was used. Preliminarily, a characterization of the SMA wire at constant and variable loads was carried out: the characteristics detected are elongation vs. electric current and elongation vs. electrical resistance. The control system is PC-based with a data acquisition card (DAQ). A drive board has been designed and built to read the wire's electrical resistance and power it by pulse width modulation (PWM). A notable result is that the actuator works with good precision and in dynamic conditions, even when it is called to support a load up to 65% different from that for which the electrical resistance-length correlation has previously been experimentally obtained, on which the control is based. This opens up the possibility of using the actuator in a counteracting configuration with a spring, which makes hardware implementation and control management simple.

This work introduces a new architecture for a time-domain feedback-based beamformer designed to meet real-time processing demands. The primary goal of this design is to locate reflective sources by estimating their direction of arrival (DOA) and signal range. Incorporating a feedback mechanism in this architecture is a unique aspect that refines localization precision. We conduct an in-depth analysis highlighting their respective benefits and limitations to compare the effectiveness of time-domain feedback beamforming against conventional time-domain methods. Our evaluation of the proposed architecture, based on critical performance indicators such as peak-to-sidelobe ratio, mainlobe width, and directivity factor, demonstrates its ability to improve beamformer effectiveness significantly.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

The uncertainty in the secondary path of an Active Noise Control (ANC) headphone affects the waterbed effect and stability of the feedback system. This study focuses on the uncertainty of the secondary path when real users wear headphones, and proposes a new uncertainty constraint based on the measured results of the secondary path transfer function under different wearing conditions of dummy head and limited subjects. This constraint and a cascaded second-order infinite impulse response filter with fixed coefficients are used to formulate a control strategic function, which is optimized by the Improved Grey Wolf Optimizer (IGWO) algorithm to obtain the optimal controller with better noise reduction performance. The proposed method and simulation model are validated based on the experimental test results. The results demonstrate that the safety factor and waterbed suppressing factor contained in the proposed uncertainty constraint ensures more stable noise reduction and effective suppression of the waterbed effect for new subjects without a priori data.

Background and Objectives: High job strain is worsening the outcome in coronary artery disease, CAD. Severe dissatisfaction on workplace, imbalance between high demands , and low rewards, are affecting the quality of life, and diminishing the duration of life, especially in CAD patients. Our study included two samples : CAD patients (experimental group), and without CAD patients, but with traditional risk factors (control group). The main objective of the study was the role played by high sensitivity C reactive protein, hs CRP, and microalbuminuria, as mediators of job strain and CAD relationship. Secondary objectives were the following: identification of the most vulnerable patients( with significant job strain) and intervention towards this category, for cardiovascular events prevention (primary or secondary). Materials and Methods: The utilized methods were the following : clinical exam; electrocardiogram; echocardiogram; non contrast enhanced computed chest tomography; laboratory findings ( lipid profile, glycemia, hs CRP, microalbuminuria); type D scale, DS 14; depression questionnaire, PHQ-9; and satisfaction with work scale, SWWS. Results: The highest values for hs CRP and microalbuminuria were noticed in patients with the lowest Likert score, for both samples CAD, and without CAD patients. The highest job strain was noticed in females. More than half of CAD patients ,with low Likert scores, revealed myocardial infarction. Conclusions: Microalbuminuria and hs CRP were statistical significant in the study as intercessors, in job strain and CAD relationship. The most vulnerable patients for vascular events were females, in both groups : CAD and “CAD waiting desk”. In CAD sample, the vascular vulnerability was also increased by high job strain.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

In this paper, a metal cutting machine position control have been designed and simulated using Matlab/Simulink Toolbox successfully. The open loop response of the system analysis shows that the system needs performance improvement. Static output feedback and full state feedback H₂ controllers have been used to increase the performance of the system. Comparison of the metal cutting machine position using static output feedback and full state feedback H₂ controllers have been done to track a set point position using step and sine wave input signals and a promising results have been analyzed.

The holistic approach of One Health, which sees human, animal, plant, and environmental health as a unit, rather than discrete parts, requires not only interdisciplinary cooperation, but standardized methods for communicating and archiving data, enabling participants to easily share what they have learned and allow others to build upon their findings.Ongoing work by NCBI and the GenomeTrakr project illustrates how open data platforms can help meet the needs of federal and state regulators, public health laboratories, departments of agriculture, and universities. Here we describe how microbial pathogen surveillance can be transformed by having an open access database along with Best Practices for contributors to follow. First, we describe the open pathogen surveillance framework, hosted on the NCBI platform. We cover the current community standards for WGS quality, provide an SOP for assessing your own sequence quality and recommend QC thresholds for all submitters to follow. We then provide an overview of NCBI data submission along with step by step details. And finally, we provide curation guidance and an SOP for keeping your public data current within the database. These Best Practices can be models for other open data projects, thereby advancing the One Health goals of Findable, Accessible, Interoperable and Re-usable (FAIR) data.

Probiotic feed additives have attracted considerable research interest in recent years because the effectiveness of probiotics can differ across microbial strains and the supplemented macroorganisms. The present study was conducted on 16 lambs divided into two groups (C - control and E - experimental). The examined lambs were aged 11 days at the beginning of the experiment and 40 days at the end of the experiment. The diet of group E lambs was supplemented with a multi-strain probiotic formulation (Lactobacillus plantarum AMT14, Lactobacillus plantarum AMT4, Lactobacillus rhamnosus AMT15, and Bifidobacterium animalis AMT30), whereas group C lambs did not receive the probiotic additive. At the beginning of the experiment (day 0) and on experimental days 15 and 30, blood was sampled from the jugular vein to determine and compare: phagocytic activity (PHAGOTEST) and oxidative metabolism (PHAGOBURST) of peripheral blood granulocytes and monocytes by flow cytometry. An analysis of the phagocytic activity of granulocytes and monocytes revealed significantly higher levels of phagocytic activity (expressed as the percentage of phagocytic cells and mean fluorescence intensity) in lambs administered the multi-strain probiotic formulation than in the control group. The probiotic feed additive also exerted a positive effect on the oxidative metabolism of both granulocytes and monocytes (expressed as the percentage of oxidative metabolism and mean fluorescence intensity) after stimulation with Escherichia coli bacteria and with PMA (4-phorbol-12-β-myristate-13-acetate).

Primates have an unparalleled ability to produce a wide range of dexterous movements, each sensitive to context and robust to perturbation. Recent progress in understanding the neural basis of movement generation comes from two largely independent ideas, “Optimal Feedback Control” and “Neural Dynamical Systems”. The optimal control framework was largely inspired by research programs from the ‘80s showing that the brain doesn’t seem to plan a simple desired movement trajectory, but instead produces movements by transforming sensory information into motor output that satisfies an optimality criterion. The more recent idea that the motor cortex acts as a dynamical system came about only as it became possible to analyze large numbers of simultaneously recorded single neurons. These two framings of the motor system have been largely incommensurate, neither able to contribute much to the understanding of the other. In this review, we reconcile these two views into a single model we call “Dynamical Feedback Control”. We propose that the dynamics in the motor cortex emerge from a sensorimotor transformation that couples the motor cortex to sensory input from the periphery, and to contextual inputs from other cortical and subcortical areas. Dynamics in motor cortex can be thought to approximate gains of a feedback controller, and by moving the neural state to different regions of state space, the motor system can rapidly alternate between different controllers. The DFC framework presents a new lens to interpret neural dynamics, and to understand how ensembles of neurons generate flexible and responsive patterns of muscle activity.

Abstract: A. baumannii exhibits resilience in harsh environments and progressively develops resistance to diverse antibacterial agents over time. This adaptability poses a significant challenge in treating an infection caused by this bacterium within healthcare settings. The presence of peptidoglycan, a crucial precursor for cell wall synthesis, contributes to this challenge. Peptidoglycan serves not only as a structural support in bacterial cells but also provides protection against adverse environmental conditions. The synthesis of the peptidoglycan layer involves a group of substrates such as N-acetylglucosamine (GlcNAc) and N-acetylmuramic acid (MurNAc), within a three-partitioned process occurring in the membrane, periplasmic space, and cytoplasm of each bacterium. Initiated in the cytoplasm and extending to the inner cell membrane, this synthesis starts with the production of nucleotide precursors. The first step involves the synthesis of UDP-GlcNAc, orchestrated by Glm (GlmS, GlmM, and GlmU) enzymes using fructose-6-phosphate. Subsequently, enzymes from the Mur family, namely MurB, MurA, MurD, MurC, MurI, MurF, and MurE, synthesize UDP-N-acetylmuramyl-pentapeptide (UDP-Mpp) from UDP-GlcNAc. Concurrently, on the cytosolic side, the production of membrane-surrounded undecaprenyl phosphate occurs, involving membrane-side proteins MraY and MurG in the biosynthesis of peptidoglycan. This review emphasizes updated information on Mur family proteins, encompassing physicochemical properties, nature of binding site, number and type of binding site residues, functional domain details, three-dimensional structural aspects, and their functions within bacterial cells. Special attention is directed towards their enzymatic role in peptidoglycan biosynthesis due to the limited availability of precursors in the market. Additionally, the review provides a comprehensive summary of existing inhibitors and ongoing efforts in identifying new targeted inhibitors, recognizing these enzymes as potential candidates for antibacterial drug design and discovery.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

Instead of the conventional 0 and 1 values, bipolar reasoning uses -1, 0, +1 to describe double-sided judgements in which neutral elements are halfway between positive and negative evaluations (e.g., “uncertain” lies between “impossible” and “totally sure”). We discuss the state-of-the-art in bipolar logics and recall two medieval forerunners, i.e., William of Ockham and Nicholas of Autrecourt, who embodied a bipolar mode of thought that is eminently modern. Starting from the trivial observation that “once a wheat sheaf is sealed and tied up, the packed down straws display the same orientation”, we work up a new theory of the bipolar nature of networks, suggesting that orthodromic (i.e., feedforward, bottom-up) projections might be functionally coupled with antidromic (i.e., feedback, top-down) projections via the mathematical apparatus of presheaves/globular sets. When an entrained oscillation such as a neuronal spike propagates from A to B, changes in B might lead to changes in A, providing unexpected antidromic effects. Our account points towards the methodological feasibility of novel neural networks in which message feedback is guaranteed by backpropagation mechanisms endowed in the same feedforward circuits. Bottom-up/top-down transmission at various coarse-grained network levels provides fresh insights in far-flung scientific fields such as object persistence, memory reinforcement, visual recognition, Bayesian inferential circuits and multidimensional activity of the brain. Implying that axonal stimulation by external sources might backpropagate and modify neuronal electric oscillations, our theory also suggests testable previsions concerning the optimal location of transcranial magnetic stimulation’s coils in patients affected by drug-resistant epilepsy.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

1) Background: Ultrasound-based strain imaging is now available in several ultrasound (US) scanners. Strain ratio (SR) can be used to quantify strain recorded simultaneously in two different user-selected areas, ideally exposed to the same amount of stress. The aim of this study was to evaluate SR variability when assessed in an in-vitro setup with a tissue-mimicking phantom, on resected tissue samples and in live tissue scanning with endoscopic applications. 2) Material and methods: Retrospective analysis of SR for quantification of elastic contrasts in a tissue-mimicking phantom containing four homogenous inclusions, in 38 resected bowel wall lesions and in 48 focal pancreatic lesions examined in vivo. Median SR and the inter-quartile range (IQR) was calculated on all external and endoscopic US-applications. The IQR/median provides a measure of the SR variability focusing on the two percentiles of the data closest to the median value. 3) Results: The overall variability of SR was lowest in a tissue-mimicking phantom (mean QR/median SR: 0.07). In resected bowel wall lesions representing adenomas, adenocarcinomas or Crohn lesions, the variability increased (mean IQR/Median: 0.62). During an endoscopic examination of focal pancreatic lesions in vivo, the variability increased further (mean IQR/Median: 2.04). 4) Conclusion: SR variability increased when assessed on different targets with growing heterogeneity and biological variability as one moved from homogeneous media to live tissues and endoscopic application. This may indicate a limitation for the accuracy SR evaluation in clinical applications.

Audit&amp;Feedback (A&amp;F) consists of multidimensional quality improvement activities, but its optimal design is still debated. Our study aims to outline how interventions of the Italian EASY-NET research program were designed, to explore whether desirable characteristics of an "ideal" A&amp;F were adopted. A&amp;F design included description of the working group, targeted clinical behaviors, selected indicators, sources, feedback procedures, corrective actions expected. Information was classified into four topics: nature of the desired action, type of data available, feedback display and delivery. Out of 9 projects, 3/9 aimed at changing a focused clinical behavior, 6/9 were generic; all projects identified clinicians as recipients, 8 explicitly considered managers. It was planned to develop an average of 27 indicators from administrative databases, as needed supplemented by ad hoc data collection. Five projects included outcome measures. Comparators derived from scientific literature or from territorial real-life data. Feedback was scheduled every 12, 6 or 3 months, or upon request, delivered as aggregate data (graphs and tables) via web platforms, e-mail, workshops, and individual meetings. In conclusion, at an early stage the projects were mostly “wide focused”, but improvements in A&amp;F design and delivery have been introduced, and projects, still ongoing, will offer interesting insights on A&amp;F effectiveness.

This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

The emergence of drug resistant pathogenic bacteria is increasingly challenging conventional antibiotics. Plant derived flavonoids are considered as potential alternatives to antibiotics due to their antimicrobial properties. However, the mechanisms by which flavonoids modulate pathogenic microorganisms’ growth are not fully understood. In our previous studies we found that Rutin, a kind of flavonoids showed inhibition against Klebsiella pneumoniae strains. In order to better understand its inhibitory mechanism on strain growth, we used both Rutin and Luteolin as treatments to incubate K. pneumoniae ATCC700603 strain. After incubation for 4 hours, the homogenous and differential effects of two different flavonoids on the growth of K. pneumoniae were evaluated. The integrated metabolomic and transcriptomic analysis was performed. The expression levels of 5,483 genes and the contents of 882 metabolites were measured. The differentially expressed genes (DEGs) and metabolites (DEMs) were screened and analyzed. The correlation between DEGs and DEMs were also studied. Our results showed that Rutin could inhibit the strain growth by changing metabolic pathways and ABC transporters pathways. Our study also revealed FU841_RS17580 and FU841_RS19145 as functional genes that played vital roles in the strain growth.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

This paper studies the contemporaneous relationship between S&P 500 index returns and log-increments of the market volatility index (VIX) via a nonparametric copula method. Specifically, we propose a conditional dependence index to investigate how the dependence between the two series varies across different segments of the market return distribution. We find that: (a) the two series exhibit strong, negative, extreme tail dependence; (b) the negative dependence is stronger in extreme bearish markets than in extreme bullish markets; (c) the dependence gradually weakens as the market return moves toward the center of its distribution, or in quiet markets. The unique dependence structure supports the VIX as a barometer of markets' mood in general. Moreover, applying the proposed method to the S&P 500 returns and the implied variance (VIX²), we find that the nonparametric leverage effect is much stronger than the nonparametric volatility feedback effect, although, in general, both effects are weaker than the dependence relation between the market returns and the log-increments of the VIX.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

Feedback trading theory is one of the most primitive theories about financial market. But for a long time，researches and modelings on this topic are rarely seen. The model in this paper shows the effects of sentiment shocks on asset prices in a market characterized by feedback trading in the long run. We find that，generally，feedback trading will lead to cognitive bias effect and trading inducement effect. Cognitive bias effect increases with the feedback trading parameter ( FTP) . In our model，the abnormal volatility of asset prices is captured by cognitive bias effect，sentiment shock effect and trading inducement effect．

Coastal marine ecosystems worldwide, like Florida Bay, are increasingly affected by tide alteration and anthropogenic disturbances which affect water quality imbalance leading to algal blooms. Increased bloom persistence is a serious threat due to the long-lasting impact on processes like carbon cycle and services like species presence. However, exploring eco-environmental feedback patterns of algal blooms remains challenging and poorly investigated, also due to the paucity of data. Florida Bay, taken as an epitome, has long experienced algal blooms in its central and western regions, and in 2006 an unprecedented bloom occurred in the eastern habitats. We analyzed the occurrence of blooms from three perspectives: (1) the spatial spreading networks of chlorophyll-a (CHLa) that pinpoints source and unbalanced habitats; (2) the fluctuations of water quality factors pre- and post-bloom outbreaks to in assess environmental impacts of ecological dysbiosis and target prevention and control of algal of blooms; and (3) the biogeochemical-spreading network topological co-evolution to quantify ecosystemic stability and ecological shift likelihood in long-term. Here, we propose Transfer Entropy (TE) to quantify dynamical interactions between spatial areas and biogeochemical factors (ecosystem connectome) underpinning bloom emergence and spreading, as well as environmental effects; the Pareto principle is defined for identifying the salient eco-environmental interactions of CHLa. We quantified the spatial dynamics of algal blooms, and thus obtained areas in need for ecological monitoring and potential bloom control. Results show that algal blooms are increasingly persistent over space with long-term negative effects on water quality factor. A dichotomy is reported between spatial ecological corridors of spreading and biogeochemical networks as well as divergence from the optimal eco-organization: randomization of the former due to nutrients' overload and temperature increase leads to scale-free CHLa spreading and extreme outbreaks a posteriori. Subsequently this increases bloom persistence, turbidity and salinity with potentially strong ecological effects on highly biodiverse and vulnerable areas such as tidal flats and marshes. Algal blooms are important ecosystem regulators of nutrient cycles; however, beyond limit chlorophyll-a outbreaks cause aquatic species mortality due to their effect on water turbidity, nutrient balance (nitrogen and phosphorus in particular), salinity and temperature. Beyond compromising local environmental quality, socio-ecological services are also compromised at large scales, yet ecological assessment models like the one presented are in need of application in subtropical and tropical bays worldwide.

The feedback collection and analysis has remained an important subject matter since long. The traditional techniques for student feedback analysis are based on questionnaire-based data collection and analysis. However, the student expresses their feedback opinions on online social media sites, which need to be analyzed. This study aims at the development of fuzzy-based sentiment analysis system for analyzing student feedback and satisfaction by assigning proper sentiment score to opinion words and polarity shifters present in the input reviews. Our technique computes the sentiment score of student feedback reviews and then applies fuzzy-logic module to analyze and quantify student’s satisfaction at the fine-grained level. The experimental results reveal that the proposed work has outperformed the baseline studies as well as state-of-the-art machine learning classifiers.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

Background: Emergency medical services (EMS) are the first health care contact for the majority of stroke patients. However, there is a lack of data on the current paramedics’ hospital-directed feedback and training needs across different health care settings. We aimed to evaluate paramedics’ prehospital stroke care knowledge, training needs, and current status of feedback on suspected stroke patients. Methods: We surveyed paramedics from the Vilnius region from September to November 2019, and compared the answers between the city and the district agencies. The questionnaire content included questions on paramedics’ demographic characteristics, prehospital stroke care self-assessment, knowledge on stroke mimics, stroke training needs, and the importance of hospital-directed feedback on suspected stroke patients. Results: A total number of 161 paramedics were surveyed, with more district paramedics rating their prehospital stroke care knowledge as inadequate (44.8% (95% confidence interval (CI) 32.8–57.6) vs 28.1% (95% CI 20.1–27.8), p = 0.028). In addition, more district paramedics indicated a need for additional stroke training (83.1% (95% CI 71.5–90.5) vs 69.8% (60.0–78.1), p = 0.043). However, respondents reported being the most confident while dealing with stroke (71.3%, 95% CI 63.8–77.7) compared to other time-critical conditions (p < 0.001). Vertigo (60.8%, 95% CI 53.0–68.0), brain tumours (56.3%, 95% CI 48.5–63.8), and seizures (54.4%, 95% CI 46.7–62.0) were indicated as the most common stroke mimics. Only 6.2% (95% CI 3.4–11.1) of respondents received formal feedback on the outcome of suspected stroke patients brought to the emergency department. Conclusion: A high proportion of paramedics self-perceive having inadequate stroke knowledge and an urgent need for further stroke training. The EMS staff indicate receiving an insufficient amount of feedback on suspected stroke patients, even though the usefulness is perceived to be paramount.

Feedback is a type of formative evaluation linked to student learning and academic achievement. However, it is not known how students perceive this process since there are no instruments to measure attitudes towards feedback. The objective of this work was to develop and validate an attitude scale towards academic feedback through an Exploratory Factor Analysis (EFA), using the principal components method and an internal consistency analysis using Cronbach's Alpha. The sample consisted of 274 students from 2015, 2016, and 2017 cohorts of pedagogy careers from five Chilean universities. The results showed the consolidation of the instrument and its final conformation in four components (Negative experience towards feedback, Effectiveness of feedback, Feedback as an opportunity, and Resistance towards feedback) with a total of 15 items, which allow measuring the students' attitude towards this written formative evaluation.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

In this paper is presented the design and syntheis of a dynamic output feedback neural network controller for a non-holonomic mobile robot. First the dynamic model of a non-holonomic mobile robot is presented, in which these constraints are considered for the mathematical derivation of a feasable representation for this kind of robot. Then two control strategies are provided based on kinematic control for this kind of robot. The first control strategy is based on driftless control, this means, that considering that the velocity vector of the mobile robot is orthogonal to its restriction a dynamic output feedback and neural network controller is designed in order that the control action would be zero only when the velocity of the mobile robot is zero. The Lyapunov stability theorem is implemented in order to find a suitable control law. Then another control strategy is designed for trajectory tracking purposes, which similar to the driftless controller, a kinematic control scheme is provided but suitable to implement in more sophisticated hardware. In both control strategy a dynamic control law is provided along with a feedforward neural network controller, so in this way, by the Lyapunov theory the stability and convergence to the origin of the mobile robot position coordinates is ensured. Finally, two numerical experiment are presented in order to validate the theoretical results synthetized in this research study. Discussions and conclusions are provided in order to analyze the results found in this research study.

Among the biggest challenges facing the contemporary human condition, and therefore also education, is responding to the climate crisis. The source of the crisis is assumed to be absent-mindedness, presented by Leslie Dewart as a distortion of the development of human consciousness. Dewart's poorly-known philosophical consciousness study is presented in this paper in broad outline. The problems in the study of consciousness, the most important of which are the qualitative representations – qualia – and the question of free will, are also briefly discussed. These problems are then examined transcendental analytically, with the question of what one must assume in order to allow the emergence of these phenomena. From the resulting conception of causal relationship, we proceed to the circular causality as a prerequisite for life, namely the homeostatic systems and negative feedback. An organization of action that is essential to animals and humans is presented, using William Powers’ perceptual control theory (PCT), and the role of consciousness in this organization is drafted according to the studies of Martin Taylor. Action is seen as continuous problem solving, in which negative feedback is used to bring perceptions into line with the goals. The fundamental function of consciousness is revealed as the direction and enhancement of learning. Based on PCT, it can be shown that the main practical problems in animal and, especially, human action, are related to adverse side effects of action and the resulting various conflicts. The climate crisis is a typical example of the problematic side effects of collective action. Dewart's concept of absent-mindedness can therefore be defined as an inability to responsibly account for the side effects of action. Thus, the main task of education is to forestall, through negative feedback and in cooperation with learner consciousness, absent-mindedness and the problems it causes.

Ultrasound based haptic feedback is a potential technology for human-computer interaction (HCI) with the advantages of low cost, low power consumption and controlled force. In this paper, the phase optimization for multipoint haptic feedback based on ultrasound array is investigated and the corresponding experimental verification is provided. A mathematical model of acoustic pressure is established for the ultrasound array and then a phase optimization model for an ultrasound transducer is constructed. We propose a pseudo-inverse (PINV) algorithm to accurately determine the phase contribution of each transducer in the ultrasound array. By controlling the phase difference of the ultrasound array, the multipoint focusing forces are formed leading to various shapes such as geometries and letters that can be visualized. Because the unconstrained PINV solution results in unequal amplitudes for each transducer, a weighted amplitude iterative optimization is deployed to further optimize the phase solution, by which the uniform amplitude distributions of each transducer are obtained. For the purpose of experimental verifications, a platform of ultrasound haptic feedback consisting of a Field Programmable Gate Array (FPGA), an electrical circuit and an ultrasound transducer array is prototyped. The haptic performances of single point, multiple points and dynamic trajectory were verified by controlling the ultrasound force exerted on the liquid surface. The experimental results demonstrate that the proposed phase optimization model and theoretical results are effective and feasible, and the acoustic pressure distribution is consistent with the simulation results.

In this manuscript, we present a high-fidelity physics-based truth model of a Single Machine Infinite Bus (SMIB) system. We also present reduced-order control-oriented nonlinear and linear models of a synchronous generator-turbine system connected to a power grid. The reduced-order control-oriented models are next used to design various control strategies such as: proportional-integral-derivative (PID), linear-quadratic regulator (LQR), pole placement-based state feedback, observer-based output feedback, loop transfer recovery (LTR)-based linear-quadratic-Gaussian (LQG), and nonlinear feedback-linearizing control for the SMIB system. The controllers developed are then validated on the high-fidelity physics-based truth model of the SMIB system. Finally, a comparison is made of the performance of the controllers at different operating points of the SMIB system.

Owing to the large ratio of consumption in the building sector, energy saving strategies are required. Energy feedback is an energy-saving strategy that consumers to change their energy-consumption behaviors. The strategy has been principally focused on providing energy-consumption information. However, realization of energy savings using only consumption information remains limited. In this paper, a building-energy three-dimensional (3D) visualization solution is thus proposed. This solution includes the process of diagnosing a building and providing prediction of energy requirements if a building improvement is undertaken. Accurate diagnostic information is provided by real-time measurement data from sensors and building models using a close-range photogrammetry (CRP) method without depending on blueprints. The information is provided by employing visualization effects to increase the energy-feedback efficiency. The proposed strategy is implemented on two testbeds, and building diagnostics are performed accordingly. For the first testbed, the predicted energy improvement amount resulting from the facility upgrade is provided. The second testbed is provided with a 3D visualization of the energy information. The aim is to determine if the building manager will replace the facility after our recommendation is given to improve the building energy efficiency driven from the energy information. Unlike existing systems, which provide only ambiguous data that lack quantitative information, this study is meaningful because it provides energy information with the aid of visualization effects before and after building improvements.

Infertility is affecting around 20 % of couples in the age of procreation but however in some societies as many as one-third of all couples are unable to conceive. Different factors are contributing to male fertility declining such us endocrine disruptors environmental and professional exposures, oxidative stress and life style changes with risks of de novo epigenetics dysregulation. Since the fantastic development of new technologies of Omes and Omics , the contribution of inherited or de novo genomes and epigenome disorders contributions in male infertility are more elucidated and relevant. More than somatic genome investigation of infertile men (from chromosome to single or multiple gene point mutations) many others techniques become available in molecular andrology laboratory to investigate the genome and epigenome integrity, the maturation and the competency of the spermatozoa and its physiological environment. All those new methods of assessment are demonstrating the role of genetics and epigenetics disorders contribution on reproductive pathology and are helping the professional of assisted reproductive technology to propose different management strategy of male infertility to improve the clinical outcomes and minimize the risk of genetics or metabolic disorders at birth.

Improving the acquisition and retention of a new motor skill is of great importance. The present study (i) investigated the effects of difficulty manipulation strategies (gradual difficulty), combined with different modalities of feedback (FB) frequency on performance accuracy and consistency when learning a novel fine motor coordination task, and (ii) examined relationships between novel fine motor task performance and executive function (EF), working memory (WM), and perceived difficulty (PD). Thirty-six, right-handed, novice physical education students volunteered to participate in this study. Participants were divided into three progressive difficulty groups (PDG), 100% visual FB (FB1), 50% FB (FB2), and 33% FB (FB3). Progressive difficulty was increased by the manipulation of the distance to the target; 2 m, 2.37 m, and 3.56 m. Three FB modalities were investigated (i.e.: 100% visual FB (100% FB), 50% reduced feedback condition (50% RFB), and 33% reduced feedback conditions (33% RFB)). Performance assessments were conducted following familiarization, acquisition, and retention learning phases. Two stress-conditions of dart throws were investigated (i.e.: free condition (FC) and time pressure condition (TPC)). After the learning intervention, data showed that, under the free condition, the 100% FB group had a significant improvement in accuracy during all learning phases. Under time pressure condition, for the 50% RFB and the 33% RFB group, the measured variable (accuracy and consistency) showed a significant linear improvement in performance. The association between the percentage of RFB frequencies and the task difficulty (50% group) may be a more appropriate and manageable cognitive load compared to the 33% RFB and the 100% FB group. The present findings could have practical implications for practitioners because, while strategies are clearly necessary for improving learning, the efficacy of the process appears to be essentially based on the characteristics of the learners.

Different factors seemingly account for the emergence of present-day languages in our species. Human self-domestication has been recently invoked as one important force favouring language complexity mostly via a cultural mechanism. As a consequence, evolutionary changes impacting on aggression levels are expected to have fostered this process. Here we hypothesise about a positive effect of dog-human interactions on aggression management and more generally, on our self-domestication, ultimately, contributing to aspects of language evolution. We review evidence of diverse sort (ethological mostly, but also archaeological, genetic, and physiological) supporting a positive feedback loop between dog domestication and human-self domestication that might have favoured the mechanisms promoting structural complexity in human languages.

This paper aims to quantify the influence of hydrogen embrittlement on Wierzbicki and Xue (W-X) model parameters. This model has 4 parameters which have been obtained by tensile tests on smooth specimens, tensile notch specimens, single notch tensile specimens (SENT) and pure shear specimens. Hydrogen embrittlement has been obtained by electrolytic method. Application of the (W-X) model has been done to get the local resistance used to predict failure by the Volumetric Method (VM). An example is given for the case of an embedded pipe submitted to service pressure and lateral seismic displacement. The effect of this displacement is then assimilated to the shearing of the straight section of the pipe. The pipe shows a corrosion defect considered a semi-elliptical crack. The influence of hydrogen embrittlement on local strain resistance and safety factors is discussed.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

Cannabidiol (CBD) is a non-intoxicating compound extracted from Cannabis sativa, showing antidepressant-like effects in different rodent models. However, inconsistent results have been described depending on the species and the strain used to assess depressive-like behaviour. Moreover, only a few studies have investigated the effect of CBD in female rodents. Therefore, we aimed to i) investigate the effects of CBD in two different strains of mice (Swiss and C57BL/6) and in a rat model of depression based on selective breeding (Flinders Sensitive and Resistant Lines, FSL and FRL) subjected to tests predictive of antidepressant-like effects; and ii) investigate the influence of sex in the effects of CBD in both mice and rats. CBD induced an antidepressant-like effect in male Swiss but not in female Swiss or C57BL/6 mice in the tail suspension test (TST). In male FSL rats, CBD produced an antidepressant-like effect one-hour post-injection. However, in female FSL, CBD induced a bimodal effect, increasing the immobility time at one hour and decreasing it at two hours. Ketamine produced an antidepressant-like effect in male and female FSL rats at different doses. In conclusion, strain, sex, and administration time affect CBD's behavioural response to rodents exposed to tests predictive of antidepressant effects.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

Structural displacement is an important metric for assessing structural conditions because it has a direct relationship with the structural stiffness. Many bridge displacement measurement techniques have been developed, but most methods require fixed reference points in the vicinity of the target structure which limits field implementations. A promising alternative is to use reference-free measurement techniques that indirectly estimate the displacement by using measurements such as acceleration, and strain. This paper proposes novel reference-free bridge displacement estimation by the fusion of single acceleration with pseudo-static displacement derived from co-located strain measurements. First, we propose a conversion of the strain at the center of a beam into displacement based on the geometric relationship between strain and deflection curves with reference-free calibration. Second, an adaptive Kalman filter is proposed to fuse the displacement generated by strain with acceleration by recursively estimate the noise covariance of displacement from strain measurements which is vulnerable to measurement condition. Both numerical and experimental validations are presented to demonstrate the efficiency and robustness of the proposed approach.

The EASY-NET network program (NET-2016-02364191 - Effectiveness of Audit and Feedback (A&F) strategies to improve health practice and equity in various clinical and organizational set-tings), piloted a new and more structured A&F strategy. This study compared the effectiveness of the new strategy versus the periodic publication of indicators alone in improving the appropri-ateness and timeliness of emergency health interventions in patients with Acute Miocardial In-farction (AMI) and ischemic stroke in the Lazio Region. Efficacy was evaluated according to a prospective quasi-experimental design of pre-post (2021-2022) intervention type with control group. The exposed are hospitals in the Lazio Region where professional teams voluntarily par-ticipated in the intervention. The control group is involved only in the usual reporting activities. Effectiveness analysis was conducted at the patient level. Regional health information systems were used to calculate process and outcome indicators. The effectiveness of the intervention was assessed with Difference In Difference models, comparing pre-post intervention periods between exposures and controls. Estimates were calculated in terms of the difference in percentage points (pp) between absolute risks. Sixteen facilities for the IMA pathway and 13 for the stroke pathway joined the intervention. The intervention reduced the proportion of 30-days readmissions after a hospitalization for ischemic stroke by 0.54 pp in the exposed patients with a significant difference of -3.80 pp (IC95% -6.57; -1.03; 5453 patients, 63.7% cases) in the exposed compared to controls. There were no statistically significant differences attributable to the implemented A&F interven-tion in the other indicators considered. The results show, for the first time in Italy, the impact of A&F interventions in an emergency setting using aggregated data from hospitals involved in the Lazio Region emergency network.

Electromagnetic actuation can support many fields of technology, such as robotics or biomedical applications. In this context, fully understanding the system behavior and proposing a low-cost package for feedback control is challenging. Modeling the electromagnetic force is particularly tricky because it is a nonlinear function of the actuated object’s position and coil’s current. Measuring in real time the position of the actuated object with the precision required for accurate motion control is also nontrivial. In this study, we propose a novel, cost-effective electromagnetic set-up to achieve position control via visual feedback. We actuate vertically and under different experimental conditions a 10 mm diameter steel ball hanging on a low-stiffness spring, demonstrating good tracking performance (the position error remains within ±0.5 mm with a negligible phase delay in the best scenarios). The experimental results confirm the feasibility of the proposed set-up, which is characterized by minimum complexity and realized with off-the-shelf and cost-effective components. For these reasons, such a contribution helps to understand and apply electromagnetic actuation even further.

Research on bidirectional human-machine interfaces will enable the smooth interaction with robotic platforms in contexts ranging from industry to tele-medicine and rescue. This paper introduces a bidirectional communication system to achieve multisensory telepresence during the gestural control of an industrial robotic arm. We complement the gesture-based control by means of a tactile-feedback strategy grounding on a spiking artificial neuron model. Force and motion from the robot are converted in neuromorphic haptic stimuli delivered on the user’s hand through a vibro-tactile glove. Untrained personnel participated in an experimental task benchmarking a pick-and-place operation. The robot end-effector was used to sequentially press six buttons, illuminated according to a random sequence, and comparing the tasks executed without and with tactile feedback. The results demonstrated the reliability of the hand tracking strategy developed for controlling the robotic arm, and the effectiveness of a neuronal spiking model for encoding hand displacement and exerted forces in order to promote a fluid embodiment of the haptic interface and control strategy. The main contribution of this paper is in presenting a robotic arm under gesture-based remote control with multisensory telepresence, demonstrating for the first time that a spiking haptic interface can be used to effectively deliver on the skin surface a sequence of stimuli emulating the neural code of the mechanoreceptors beneath.

The metrological performance of FBG strain sensing systems is a critical premise for the precision of plastics water support pipeline structural deformation measurement, but the strain transfer loss of FBG attached on the plastics pipe subjected by dynamic force is unclear. This paper presents the first study on the effects of strain transfer between FBG, and acrylate polymer blended with poly resin (ABR)pipe sheets loaded by static and dynamic force. Theoretical methods of dynamic strain transfer theory combine with the exponentially decaying sinusoidal shock force time course is deduced and various dynamic parameters sensitivities studies are carried out, as well as that of the geometric parameters. The result of the dynamic theory is compared with the calibration test outcomes, while the ASTR of FBG attached on ABR sheet is compared with distributed optical fiber sensors (DOFS) and other pipe materials such as PVC, concrete, and steel. Results show that the ASTR of FBG is more accurate than that of the DOFS, and the grows of ASTR depending on the paste length of FBG, the Young's modulus of the middle materials, the thickness of the middle materials and attenuation coefficient. Paste length produced the largest increase, yet the magnitude and loading speed of the external force has unexpectedly little effect on ASTR. FBG seem low error, insensitive with dynamic force and independent with the material of matrix, and this demonstrates benefits that are stronger across the board than DOFS. This is not currently recognized by standards or by most reported studies.

At an energy flux imbalance of about 1 W m–2, the ocean is storing 90 % of the heat accumulating by global warming. However, neither the causes nor the responsible geophysical processes are sufficiently well understood. More detailed investigations of the different phenomena contributing to the oceanic energy balance are warranted. Here, the role of low-level marine clouds in the air-sea interaction is analysed. TEOS-10, the International Thermodynamic Equation of State of Seawater – 2010, is exploited for a rigorous thermodynamic description of the climatic trend of the Lifted Condensation Level (LCL) of the marine troposphere. Rising Sea-Surface Temperature (SST) at constant Relative Humidity (RH) is elevating marine clouds, cooling the cloud base and reducing the downward thermal radiation. This LCL feedback effect is negative and counteracting ocean warming. At the current global SST of about 292 K, the net radiative heat flux from the ocean surface to the LCL cloud base is estimated to 24 W m–2. Per degree of SST increase, this net flux is expected to be enhanced by almost 0.5 W m–2. The climatic LCL feedback effect is relevant for the ocean’s energy balance and may thermodynamically rigorously be modelled in terms of TEOS-10 equations. LCL height may serve as a remotely measured, sensitive estimate for sea surface relative fugacity, or conventional relative humidity.

The present study illustrates a brain-computer interface designed and developed to be wearable, portable, and user-friendly. Eight dry electroencephalographic sensors were adopted to acquire the brain activity associated with motor imagery. Multimodal feedback in extended reality was exploited to improve the detection of neurological phenomena. Twenty-seven healthy subjects used the proposed system in five sessions to investigate the effects of feedback on motor imagery. The sample was divided into two equal-sized groups: the "neurofeedback" group, which performed motor imagery while receiving feedback, and the "control" group, which performed motor imagery with no feedback. Several questionnaires were administrated to participants aiming to investigate the usability of the proposed system and individual’s ability to imagine movements. The highest mean classification accuracy across subjects of control group was about 62 % with 3 % associated type A uncertainty, and 69 % with 3 % uncertainty for neurofeedback group. Moreover, in some cases the results were significantly higher for the neurofeedback group. The perceived usability by all participants was high. Overall, the study highlights the advantages and the pitfalls of using a wearable brain-computer interface with dry sensors. Notably, the results and the perceived usability pave the way for the employment of the proposed system in tele-rehabilitation.

The advancements in the study of the human sense of touch are fueling the field of haptics. This is paving the way for augmenting the sensory perception during objects palpation in tele-surgery, and reproducing the information through tactile feedback. Here, we present a novel tele-palpation apparatus that enables the user to detect nodules with various distinct stiffness buried in an ad-hoc polymeric phantom. The contact force measured by the platform was encoded using a neuromorphic model and reproduced on the index fingertip of a remote user through a haptic glove embedding a piezoelectric disk. We assessed the effectiveness of this feedback in allowing nodule identification under two experimental conditions of real-time telepresence: In Line of Sight (ILS), where the platform was placed in the visible range of a user; and the more demanding Not In Line of Sight (NILS), with the platform being 50 km apart. We found that the entailed percentage of identification was higher for stiffer inclusions with respect to the softer ones (average of 74% within the duration of the task), in both telepresence conditions evaluated. These promising results call for further exploration of tactile augmentation technology for telepresence in medical interventions.

Multiobjective optimization plays an increasingly important role in modern applications, where several criteria are often of equal importance. The task in multiobjective optimization and multiobjective optimal control is therefore to compute the set of optimal compromises (the Pareto set) between the conflicting objectives. The advances in algorithms and the increasing interest in Pareto optimal solutions have led to a wide range of new applications related to optimal and feedback control which results in new challenges such as expensive models or real-time applicability. Since the Pareto set generally consists of an infinite number of solutions, the computational effort can quickly become challenging which is particularly problematic when the objectives are costly to evaluate or when a solution has to be presented very quickly. This article gives an overview over recent developments in accelerating multiobjective optimal control for complex problems where either PDE constraints are present or where a feedback behavior has to be achieved. In the first case, surrogate models yield significant speed-ups. Besides classical meta-modeling techniques for multiobjective optimization, a promising alternative for control problems is to introduce a surrogate model for the system dynamics. In the case of real-time requirements, various promising model predictive control approaches have been proposed, using either fast online solvers or offline-online decomposition. We also briefly comment on dimension reduction in many-objective optimization problems as another technique for reducing the numerical effort.

(1) Background: Group A rotaviruses (RVAs) are the primary cause of severe intestinal diseases in piglets. Porcine rotaviruses (PoRVs) are widely prevalent in Chinese farms, resulting in significant economic losses to the livestock industry. However, isolation of PoRVs is challenging, and their pathogenicity in piglets is not well understood. (2) Methods: We conduct clinical testing on a farm in Jiangsu Province, China, and isolate strains of porcine rotavirus by continuously passaging on MA104 cells. Subsequently, the pathogenicity of the isolated strain in piglets was investigated.The piglets of the PoRV-infection group were orally inoculated with 1 mL of 1.0 × 10⁶ TCID50 PoRV, whereas those of the mock-infection group were fed with an equivalent amount of DMEM. (3) Results: Fecal samples were collected from 28 piglets, all of which tested positive for RVAs. A G5P[23] genotype porcine rotavirus strain was successfully isolated from one of the positive samples and named RVA/Pig/China/JS/2023/G5P[23](JS). The genomic constellation of this strain was G5-P[23]-I5-R1-C1-M1-A8-N1-T1-E1-H1. Sequence analysis revealed that the genes VP3, VP7, NSP2, and NSP4 of the JS strain were closely related to human RVAs, whereas the remaining gene segments were closely related to porcine RVAs, indicating a reassortment between porcine and human strains. Furthermore, infection of 15-day-old piglets with the JS strain resulted in a diarrheal rate of 100% (8 of 8) and mortality rate of 37.5% (3 of 8).(4) Conclusion: The isolated G5P [23] genotype rotavirus strain, which exhibited strong pathogenicity in piglets, may have resulted from recombination between porcine and human strains. It may serve as a potential candidate strain for developing vaccines, and its immunogenicity can be tested in future studies.

We present the results of a twofold experimental and computational study of (0001) GaN/AlN multilayers forming pseudomorphic superlattices. High-Resolution Transmission Electron Microscopy (HRTEM) shows that heterostructures with GaN Quantum Wells (QW) four c-lattice parameters thick are misfit-dislocation free. Accurate structural data are extracted from HRTEM images via a new methodology optimizing the residual elastic energy stored in the samples. Total energy calculations are performed with several models analogous to the experimental QWs with increasing thicknesses of GaN, whereas this of the AlN barrier is kept fixed at n=8 c-lattice parameters. With vanishing external stresses, minimum energy configurations of the studied systems correspond to different strain states. Linear elasticity accurately yields the corresponding lattice parameters, suppressing the need for on-purpose total energy calculations. Theoretically justified parabolic fits of the excess interfacial energy yield the values of interfacial stress and elastic stiffness as functions of the GaN QW thickness. Total species-projected densities of states and gap values extracted therefrom allow deciphering the effect of the evolving strain on the electronic structure of the superlattice. It is found that the gap energy decreases linearly with increasing the strain of the QW. These results are briefly discussed in the light shed by previous works from the literature.

Isometric exercises for physiotherapeutic rehabilitation are often prescribed, with little quantification of the load being prescribed. This article aimed to provide a framework and practical examples of how the physiotherapist may take a more quantitative evidence-based approach to isometric assessment, monitoring, and exercise prescription of knee osteoarthritis, by integrating a strain gauge into their practice. Strength measures to monitor were discussed. A series of fourteen studies were reviewed, with the intent of identifying isometric exercises that had been utilized in the rehabilitation of knee osteoarthritis. Of the fourteen studies, the three most identified isometric exercises were seated knee extension, knee flexion, and the supine straight leg raise. The integration of strain gauge technology with these exercises provided the focus of the remainder of the article.

Signal preprocessing and feature extraction are two important and necessary steps of data analysis. In signal analysis, typically these two steps are implemented through multiple algorithms. Moreover, the significant parameters in most algorithms are set empirically. We have developed an algorithm that can preserve and highlight characteristic waveforms while attenuating non-feature waveforms. The parameters in the algorithm are set through difference analysis. We have conducted experiments on both clinical and open-source ECG data, obtaining effective test results.

Patients with low back pain often have deficits in trunk stability. For this reason, many patients receive physiotherapy treatment, which represents an enormous socio-economic burden. Training at home could reduce these costs. The prob-lem here is the lack of correction of the exercise execution. This feasibility study therefore investigates the applicability of a vibrotactile-controlled feedback system for trunk stabilization exercises. A sample of 13 healthy adults performed three trunk stabilization exercises. Exercise performance was corrected by physiotherapists using vibrotactile feedback. The NASA TLX questionnaire was used to assess the practicability of the vibrotactile feedback. The Nasa TLX questionnaire show a very low global workload M = 37.96 (SD =11.63). The quality of feedback perception was perceived as good by the subjects, varying between 76.9 % and 92.3 % depending on the body part. 80.8 % rated the feedback as helpful for their training. On the expert side, the results show a high rating of movement quality. The positive evaluations of the physiotherapists and the participants on the use of the vibrotactile feedback system indi-cate that such a system can reduce the trainees fear of independent training and support the users in their training. This could increase training adherence and long-term success.

In today's business world, many companies have realized that consumer feedback evaluations play a crucial part in shaping the company's future activities. The hotel and tourism industries are well-known examples where the user feedback has become crucial. Even though most accommodations want their clients to express their opinions about their services, these reviews are nevertheless carefully reviewed by them. This manual approach is time demanding and error prone, the level of expertise of the individual analyzing the evaluations determines the quality of the manual analysis. This research focuses on the development of a tool-based support system that analyzes text-based customer evaluations and then highlights the maintenance issues identified in the reviews, removing the need to manually evaluate and analyze the customer reviews. The process includes data preparation, sentiment analysis, and a fully trained deep learning model to extract critical insights. Using sentiment analysis techniques after data preprocessing and trained deep learning model, an accuracy of 96\% was achieved, and this paper discusses how this technology helps to meet the needs of accommodation management by completing activities efficiently. This might save management time and helps to save money without losing clients, allowing them to enhance their additional sales.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Mycobacterium tuberculosis variant bovis (MBO) has one of the widest known mammalian host ranges, including humans. Despite characterization of this pathogen in the 1800s, and whole genome sequencing of a UK strain (AF2122) nearly two decades ago, the basis of its host specificity and pathogenicity remains poorly understood. Recent experimental calf infection studies show that MBO strain Ravenel (MBO Ravenel) is attenuated in the cattle host. In the present study, experimental infections were performed to define attenuation and whole genome sequencing completed to identify regions of differences (RD) and single nucleotide polymorphisms (SNPs) to explain the observed attenuation. Comparative genomic analysis of MBO Ravenel against three pathogenic strains of MBO (strains AF2122-97, 10-7428 and 95-1315) was performed. Experimental infection studies on 5 calves each, with either MBO Ravenel or 95-1315, revealed no visible lesions in all 5 animals in the Ravenel group despite robust IFN-γ responses. Out of 486 polymorphisms in the present analysis, 173 were unique to MBO Ravenel among the strains compared. A high-confidence subset of 9 unique SNPs were missense mutations in genes with annotated functions impacting 2 major MBO survival and virulence pathways: 1) Cell wall synthesis & transport [espH (A103T), mmpL8 (V888I), aftB (H484Y), eccC5 (T507M), rpfB (E263G)], and 2) Lipid metabolism & respiration [mycP1(T125I), pks5 (G455S), fadD29 (N231S), fadE29 (V360G)]. These substitutions likely contribute to the observed attenuation. Results from experimental calf infections and the functional attributions of polymorphic loci on the genome of MBO Ravenel provide new insights into the strain’s genotype-disease phenotype associations.

In this study, a flexible strain sensor is devised using corrugated poly(3-hexylthiophene) (P3HT) thin film. In the previous studies, the P3HT-based photoactive thin film was shown to generate direct current (DC) under broadband light, and the generated DC voltage varied with applied tensile strain. Yet, the mechanical resiliency and strain sensing range of the P3HT-based thin film strain sensor were limited due to relatively more brittle thin film constituent—poly(3,4-ethylenedioxythiophene)-polystyrene(sulfonate) (PEDOT:PSS) conductive thin film as a bottom electrode. To address this issue, it is aimed to design mechanically resilient strain sensor using corrugated thin film constituents. Buckling is induced to form corrugation in the thin films by applying pre-strain to the substrate, where the thin films are deposited, and releasing the pre-strain afterwards. It is known that corrugated thin film constituents exhibit different optical and electronic properties from non-corrugated ones. Therefore, to optimize design of the flexible strain sensor, it was studied to understand how the applied pre-strain and thickness of the PEDOT:PSS thin film affect the optical and electrical properties. Also, pre-strain effect on light absorptivity of the corrugated P3HT-based thin films was studied. In addition, strain effect was investigated on the optical and electrical properties of the corrugated thin film constituents. Finally, flexible strain sensors are fabricated by following the design guideline, which is suggested from the studies on the corrugated thin film constituents, and DC voltage strain sensing capability was validated. As a result, flexible strain sensor exhibited tensile strain sensing range up to 5% at frequency up to 15 Hz with maximum gage factor ~7.

Although instructional feedback plays an essential role in regulating learning and improving performance, few studies have systematically investigated the needs of teachers and students for instructional feedback system or developed designs and experiments, especially at the high school level. To address this research need, the present study investigated the needs of selected students and teachers in a high school in Hubei Province, China, and designed and developed a diagnostic visual feedback system for an experimental study with 125 students from a 10th-grade biology class in the same high school. The results showed that this diagnostic visual feedback report improved student performance (ES=0.37) and that functions such as misconception location, knowledge diagnosis, and knowledge alert were well received by students. These findings have multiple implications for facilitating the design and development of diagnostic visual feedback system.

The PI3K/mTOR signalling pathway plays a central role in the governing of cell growth, survival and metabolism. As such, it must integrate and decode information from both external and internal sources to guide efficient decision-making by the cell. To facilitate this, the pathway have evolved an intricate web of complex regulatory mechanisms and elaborate crosstalk with neighbouring signalling pathways, making it a highly non-linear system. Here, we describe the mechanistic biological details that underpin these regulatory mechanisms, covering a multitude of negative and positive feedback loops, feed-forward loops, competing protein interactions, and crosstalk with major signalling pathways. Further, we highlight the non-linear and dynamic network behaviours that arise from these regulations, uncovered through both computational and experimental studies. Given the pivotal role of the PI3K/mTOR network in cellular homeostasis and its frequent dysregulation in pathologies including cancer and diabetes, a coherent and systems-level understanding of the complex regulation and consequential dynamic signalling behaviours within this network is imperative for advancing biology and development of new therapeutic approaches.

The goal of the current study was to discover a novel potential probiotic strain of Lactobacillus spp. with anti-Escherichia coli activity from locally produced yogurt in Tongi, Gazipur, Bangladesh, compare its antagonistic activity with a commercial probiotic mixture of several strains, and approve a novel method for confirming the viability and relative abundance of the microbial community in a probiotic mixer. We carried out 16S sequencing, 16S metagenomics, Transmission Electron Microscopy (TEM) analysis, and other in vitro laboratory experiments to reach this objective. The strain TY-11 was identified as Lactobacillus delbrueckii subsp. indicus (16S sequence accession number OQ652026). It was gram-positive, anaerobic, lactose fermenting, and round-ended rod that typically measured 0.7 to 1.3 µm by 2.2 to 9 µm. In addition to having seven probiotic characteristics, it also showed an antagonistic impact on six different pathogens, but what's more noteworthy is that E. coli was the pathogen it inhibited most strongly (inhibition zone diameter was 18.88±0.18 mm). The most important and ground-breaking finding of this work was determining the probiotic features of a new probiotic strain, TY-11, whose antibacterial activity was virtually as effective as that of the probiotic combination with three different strains. Furthermore, the results of 16S high throughput sequencing and the conventional plate count method demonstrated a strong correlation (0.999) at the genus level, indicating that the use of both of these approaches in combination may be a practical way to assess the relative abundance of the microbial community and their viability in commercially available probiotic blends.

Various crystallite size estimation methods were used to analyze X-ray diffractograms of spherical cerium dioxide and donut-like titanium dioxide anatase nanoparticles aiming to evaluate their reliability and limitations. The microstructural parameters were estimated from Scherrer, Monshi, Williamson-Hall, and their variants: i) uniform deformation model, ii) uniform strain deformation model, and iii) uniform deformation energy density model, and also size-strain plot, and Halder-Wagner method. For that, and improved systematic Matlab code was developed to estimate the crystallite sizes and strain, and the linear regression analysis was used to compare all the models based on the coefficient of determination, where the Halder Wagner method gave the highest value (close to 1). Therefore, being the best candidate to fit the X-ray Diffraction data of metal-oxide nanoparticles. Advanced Rietveld was introduced for comparison purposes. Refined microstructural parameters were obtained from a nanostructured 40.5 nm Lanthanum hexaboride nanoparticles and correlated with the above estimation methods and transmission electron microscopy images. In addition, electron density modelling was also studied for final refined nanostructures, and μ-Raman spectra were recorded for each material estimating the mean crystallite size and comparing by means of a phonon confinement model.

Since the first published genome sequence of Trypanosoma cruzi in 2005, there has been tremendous technological advance in genomics, reverse genetics, and assay development for this elusive pathogen. However, there is still an unmet need for new and better drugs to treat Chagas disease. Here we introduce a T. cruzi assay strain that is useful for drug research as well as basic studies in host-pathogen interaction. Trypanosoma cruzi STIB980 is a strain of discrete typing unit TcI that grows well in culture as axenic epimastigotes or intracellular amastigotes. We have evaluated the optimal parameters for genetic transfection and constructed derivatives of T. cruzi STIB980 that express reporter genes for fluorescence- or bioluminescence-based drug efficacy testing, as well as a Cas9-expressing line for CRISPR/Cas9-mediated gene editing. The genome of T. cruzi STIB980 was sequenced by combining short-read Illumina with long-read Oxford Nanopore technologies. The latter served for the primary assembly, the former to correct mistakes and fill the gaps. This resulted in a high-quality nuclear haplotype assembly of 28 Mb in 400 contigs, containing 10,043 open-reading frames with a median length of 1077 bp. We believe that T. cruzi STIB980 is a useful addition to the antichagasic toolbox, and propose that it can serve as a DTU TcI reference strain for drug efficacy testing.

This paper presents a thorough review of Electrical Muscle Stimulation (EMS) in the context of Augmented Reality (AR) and Virtual Reality (VR), specifically focusing on its application in providing kinesthetic feedback. Our systematic review of 17 studies reveals the growing interest and potential of EMS in this domain, as evidenced by the growing body of literature and citations. Key elements presented in our review encompass a catalog of the applications developed to date, specifics of the stimulation parameters used, the participant demographics of the studies, and the types of measures used in these research efforts. We discovered that EMS offers a versatile range of applications in AR/VR, from simulating physical interactions like touching virtual walls or objects, to replicating the sensation of weight and impact. Notably, EMS has shown effectiveness in areas such as object handling and musical rhythm learning, indicating its broader potential beyond conventional haptic feedback mechanisms. However, our review also highlights major challenges in the research, such as inconsistent reporting of EMS parameters and a lack of diversity in study participants. These issues underscore the need for improved reporting standards and more inclusive research approaches to ensure wider applicability and reproducibility of results.

Feedback control plays a crucial role in improving system accuracy and stability for a variety of scientific and engineering applications. Here, we theoretically and experimentally investigate the implementation of feedback control in microwave photonic (MWP) transversal filter systems based on optical microcomb sources, which offer advantages in achieving highly reconfigurable processing functions without requiring changes to hardware. We propose four different feedback control methods including (1) one-stage spectral power reshaping, (2) one-stage impulse response reshaping, (3) two-stage spectral power reshaping, and (4) two-stage synergic spectral power reshaping and impulse response reshaping. We experimentally implement these feedback control methods and compare their performance. The results show that the feedback control can significantly improve not only the accuracy of comb line shaping as well as temporal signal processing and spectral filtering, but also the system’s long-term stability. Finally, we discuss the current limitations and future prospects for optimizing feedback control in microcomb-based MWP transversal filter systems implemented by both discrete components and integrated chips. Our results provide a comprehensive guide for the implementation of feedback control in microcomb-based MWP filter systems in order to improve their performance for practical applications.

Pose estimation has various applications in analyzing human movement and behavior, including providing feedback to users about their movements so they could adjust and improve their movement skills. To investigate the current research status and possible gaps, we searched Scopus and Web of Science for articles that (1) human `body' pose estimation is used and (2) user movement is assessed and communicated. We used either a bottom-up or top-down approach to analyze 20 articles for methods used to estimate human pose, assess movement, provide feedback to users, as well as methods to evaluate them. Our review found that pose estimation systems typically used CNNs while movement assessment methods varied from mathematical formulas or models, rule-based approaches, to machine learning. Feedback was primarily presented visually in verbal forms and nonverbal forms. The experiments to evaluate each part ranged from the use of public datasets to human participants. We found that while there was an improvement, the majority of pose estimation challenges remain. The effectiveness and factors for choosing movement assessment methods for a new context are still unclear. In the end, we suggest that studies about feedback prioritization and erroneous feedback are needed.

A comparative analysis of the features of UV- stimulated emission (SE) of various types of disorder active materials based on ZnO crystallites for a random laser (RL) was carried out. The superlinear increase in the intensity of the UV photoluminescence (PL) band of polydisperse nano- microcrystalline (PNMC) ZnO powder at a wavelength of λ = 387 nm and some narrowing of its half-width in the range of 20-15 nm with increasing pump intensity indicate random lasing with incoherent feedback (FB). Properties of similar UV PL bands under the same conditions from a thin film containing hexagonal ZnO microdisks, as well as samples of monodisperse ZnO nanopowder indicate stimulated emission with coherent feedback. It is shown that, among the studied materials, the PNMC ZnO powder with crystallites contained nano-grains with is the most suitable for creating a laser with incoherent feedback at room temperature. The dominant factor of UV SE in PNMC ZnO powder is radiation transitions under exciton - exciton scattering conditions. The possible mechanisms of this random emission with the continuous spectrum are discussed. The average optical gain coefficient αg at λ = 387 nm in this RL system is estimated, as αg ~ 150 cm-1.

Within the field of movement sensing and sound interaction research, multi-user systems have gradually gained interest as a means to facilitate an expressive non-verbal dialogue. When tied with studies grounded in psychology and choreographic theory, we consider the qualities of interaction that foster an elevated sense of social connectedness, non-contingent to occupying one’s personal space. In reflection of the newly adopted social distancing concept, we orchestrate a technological intervention, starting with interpersonal distance and sound at the core of interaction. Materialised as a set of sensory face-masks, a novel wearable system was developed and tested in the context of a live public performance from which we obtain the user’s individual perspectives and correlate this with patterns identified in the recorded data. We identify and discuss traits of the user’s behaviour that were accredited to the system’s influence and construct 4 fundamental design considerations for physically distanced sound interaction. The study concludes with essential technical reflections, accompanied by an adaptation for a pervasive sensory intervention that’s finally deployed in an open public space.

The aim of this paper is to examine the beneficial impact of feedback information in the dynamics of production-inventory control systems. Two production-inventory control system models are analyzed: APIOBPCS and 2APIOBPCS models. The simulation-based experiment designs were conducted by using the state-space equations of the two models. The bullwhip effect as measured by the variance ratio between the order rate and the consumption rate, and inventory responsiveness as measured by the Integral of Absolute Error between the actual and the target levels of inventory, are two metrics used to evaluate the performance of the production-inventory control system in response to a random customer demand. To ensure that both models work under optimal performance, multi-objective particle swarm optimization (MOPSO) is employed to address the problem of tuning the controller’s parameters. The simulation results show the 2APIOBPCS model outperforms the APIOBPCS model at achieving the desired bullwhip effect and being able to provide better inventory responsiveness. The improvement in the inventory responsiveness becomes more significant when the system operates under mismatched lead time and/or an initial condition.

(1)Background: Early-age concrete shrinkage induces stress that impact the cost and service life of concrete pavements. (2)Methods: In this study, strain measurements of field slabs were conducted and a methodology was presented that independently derived autogenous, drying, and thermal shrinkages in the initial stages of concrete placement. Total strain was measured according to five different environmental conditions and shrinkage strain was calculated for each condition. (3)Results: By measuring the strain of the slab and the specimen, the drying shrinkage strain was measured to be approximately 54% better than that by the conventional non-stressed cylinder method because it was possible to measure the drying shrinkage strain at the surface rather than in the middle part of the slab along its depth direction. When the water-to-cement ratio increased (35→40%), there was a considerable reduction (317με→82με) of autogenous shrinkage strain for the concrete at 28 days of age. Furthermore, calculation of stress-dependent strain allowed the presentation of more intuitive and accurate results. (4)Conclusion: As the measurement of independent shrinkage occurrence is possible, the consequent calculated result of the stress-dependent strain acting on real slabs will facilitate improvement in the construction quality, reduction in the development of defects in the concrete structure, and increase in the service life.

Usually, the vector control of the induction machine (IM) is done by using cascade control structures with conventional linear PI controllers, the inner loop being designed for current control, and the outer loop for rotor flux and speed control. In this paper, starting from the dq model of the IM with the rotor magnetic flux space vector aligned along the d axis, advanced control algorithms are proposed for the two control loops of the cascade structure. For the current inner loop, after the decoupling control of the two dq currents, predictive algorithms with constraints are used to control and limit the currents. Since the outer loop has a nonlinear affine multivariable plant model, a homotopy-based variant of feedback linearization is used to obtain a non-singular decoupling matrix of the feedback transformation even when the rotor flux is zero at the start-up of the motor. During the continuous variation of the homotopy parameter, the model of the plant is variable, in which case the model free algorithms are properly used to control the flux and speed of the IM. The comparative analysis obtained for the cascade structure with conventional PI controllers and advanced algorithms, respectively, shows that the last lead to improve the dynamical performance of the IM.

This research work presents the nonlinear control framework to estimate and reject the mismatched lumped disturbances acting on the nonlinear uncertain system. It is an unfortunate fact that the conventional Extended State Observer (ESO) is not capable to estimate the mismatched lumped disturbance and its derivative simultaneously for the systems. Also, the basic ESO is only suitable for systems with Integral Chain Form (ICF) structure. Similarly, the conventional Feedback Linearizing Control (FLC) approach is not robust for stabilizing the systems in the presence of disturbances and uncertainties. Hence, the nonlinear control framework is proposed to overcome the above issues which are composed of, (a) Dual Extended State Observer (DESO), and (b) DESO based FLC. The DESO provides information on the unmeasured state, mismatched disturbance, and its derivative. While the DESO-FLC utilizes the information from DESO to counter the effect of such disturbances and to stabilize the nonlinear systems around the reference point. The detailed closed-loop analysis is presented for the proposed control framework in the presence of lumped disturbances. The performance robustness of the presented design has been validated for the third order, nonlinear, unstable, and disturbed Magnetic Levitation System (MLS). The results of the DESO-FLC approach are compared with the most popular Linear Quadratic Regulator (LQR) and nonlinear FLC approaches based on the integral error criterion and the average electrical energy consumption.

Electron Beam Melting (EBM) is an increasingly used Additive Manufacturing (AM) technique employed by many industrial sectors, including the medical device and aerospace industries. The application of this technology is, however, challenged by the lack of process monitoring and control system that underpins process repeatability and part quality reproducibility. An electronic imaging system prototype has been developed to serve as an EBM monitoring technique, the capabilities of which have been verified at room temperature and at 320+10°C. Nevertheless, in order to fully assess the applicability of this technique, the image quality needs to be investigated at a range of elevated temperatures to fully understand the influence of thermal noise due to heat. In this paper, electronic imaging pilot trials at elevated temperatures, ranging from room temperature to , were carried out. Image quality measure Q of the digital electron images was evaluated, and the influence of temperature was investigated. In this study, raw electronic images generated at higher temperatures had greater Q values, i.e. better global image quality. It has been demonstrated that, for temperatures between , the influence of temperature on electronic image quality was not adversely affecting the visual clarity of image features. It is envisaged that the prototype has significant potential to contribute to in-process EBM monitoring in many manufacturing sectors.

The current work addresses the control of two-input two-output (TITO) Wood and Berry model of a binary distillation column. The controller design problem is formulated in terms of multivariable H_∞ control synthesis. The controller structure takes the form of simplest static output feedback (SOF) control. The controller synthesis is performed using a hybrid approach of blending linear matrix inequalities (LMI) and genetic algorithm (GA). The performance of the static output feedback controller is compared with three other controllers designed for Wood and Berry model available in the literature. The first simulation study is performed for the case of tracking a unit step command in the presence of a step change in output disturbance. A second simulation study is performed for rejecting a change in sinusoidal output disturbance.

This work presents a linear smoothing scheme over high-order triangular elements in the framework of a cell-based strain smoothed finite element method for two-dimensional nonlinear problems. The main idea behind the proposed linear smoothing scheme for strain-smoothed finite element method (S-FEM) is no subdivision of finite element cells to sub-cells while the classical S-FEM needs sub-cells. Since the linear smoothing function is employed, S-FEM is able to use quadratic triangular or quadrilateral elements. The modified smoothed matrix obtained node-wise is evaluated. In the same manner with the computation of the strain-displacement matrix, the smoothed stiffness matrix and deformation graident are obtained over smoothing domains. A series of benchmark tests are investigated to demonstrate validity and stability of the proposed scheme. The validity and accuracy are confirmed by comparing the obtained numerical results with the standard FEM using 2nd-order triangular element and the exact solutions.

We show how the excitonic features of biaxial MoS₂ flakes are very sensitive to biaxial strain. We find a lower bound for the gauge factors of the A exciton and B exciton of (-41 ± 2) meV/% and (-45 ± 2) meV/% respectively, which are larger than those found for single-layer MoS₂. Interestingly, the interlayer exciton feature also shifts upon biaxial strain but with a gauge factor that is systematically larger than that found for the A exciton, (-48 ± 4) meV/%. We attribute this larger gauge factor for the interlayer exciton to the strain tunable van der Waals interaction due to the Poisson effect (the interlayer distance changes upon biaxial strain).

A new utilization of entropy in the context of buckling is presented. The novel concept connecting strain energy and entropy for a pin-ended strut is derived. This concept rationalizes the ranking of buckling modes based on strain energy under the assumption of given entropy. By assigning identical entropy to all buckling modes, they can be ranked according to their deformation energy. Conversely, with identical strain energy assigned to all modes, ranking according to entropy is possible. Decreasing entropy was found to represent the scaling factors of buckling modes that coincide with the measurement of initial out-of-straightness imperfections in IPE160 beams. Applied to steel plane frames, scaled buckling modes can be used to model initial imperfections. It is demonstrated that the entropy (scale factor) for given energy roughly decreases with the inverse square of the mode index. For practical engineering, the study presents the possibility of using scaled buckling modes of steel plane frames to model initial geometric imperfections. Entropy proves to be a valuable complement to strain energy in structural mechanics.

This study investigates the microstructures and deformation mechanism of hetero-structured pure titanium under different high strain rates (500 s-1，1000 s-1，2000 s-1). The influence of strain rate on the deformation mechanism is examined. As the strain rate increases, the dominance of dislocation slip decreases while deformation twinning becomes more prominent. Notably, at a strain rate of 2000s-1, nanoscale twin lamellae are activated within grain with a size of 500nm, which is a rarely observed phenomenon in pure Ti. Additionally, martensitic phase transformation is also identified. These findings can greatly enhance our understanding of the mechanical responses of Ti and broaden the potential applications of Ti in dynamic deformation scenarios.

Staphylococcus aureus is a high-priority pathogen causing severe infections with high morbidity and mortality worldwide. Many S. aureus strains are methicillin-resistant (MRSA) or even multi-drug resistant. It is one of the most successful and prominent modern pathogens. An effective fight against S. aureus infections requires novel targets for antimicrobial and antistaphylococcal therapies. Recent advances in whole-genome sequencing and high-throughput techniques facilitate the generation of genome-scale metabolic models (GEMs). Among the multiple applications of GEMs is drug-targeting in pathogens. Hence, comprehensive and predictive metabolic reconstructions of S. aureus could facilitate the identification of novel targets for antimicrobial therapies. This review aims at giving an overview of all available GEMs of multiple S. aureus strains. We downloaded all 114 available GEMs of S. aureus for further analysis. The scope of each model was evaluated, including the number of reactions, metabolites, and genes.Furthermore, all models were quality-controlled using Mᴇᴍᴏᴛᴇ, an open-source application with standardized metabolic tests. Growth capabilities and model similarities were examined. This review should lead as a guide for choosing the appropriate GEM for a given research question. With the information about the availability, the format, and the strengths and potentials of each model, one can either choose an existing model or combine several models to create models with even higher predictive values. This facilitates model-driven discoveries of novel antimicrobial targets to fight multi-drug resistant S. aureus strains.

In California, an average of 41,900 patients are diagnosed annually with Staphylococcus bacterial infection; out of these, 24,090 patients have methicillin-resistant Staphylococcus aureus (MRSA) infection and 17,810 patients have methicillin-sensitive Staphylococcus aureus (MSSA) infection. The aim of this paper is to find out whether there is a significant difference in strain dominancy and in what direction. The paper gathered and analyzed data for period of five years of infection rate due to Staphylococcus aureus. This study indicates that a significant difference in dominancy exists, the MRSA infection rate (an average of five years period) is 1.35 times higher than the MSSA infection rate (P-value < 0.05, CI: 95%), but the gap between the two infection rates is decreasing. The infection rate of both MRSA and MSSA is in a path of decline.

This paper presents an observer-based dynamic output feedback controller design procedure using Linear Matrix Inequality (LMI) optimization for second-order systems with uncertainty and persistent perturbation in the states. Using linear-quadratic criteria, cost functions are minimized in a two-stage procedure to compute optimal state feedback gains, and observer gains are coupled into a dynamic output feedback optimal controller. The LMI set used in the two stages is matrix inversion-free, a key issue for polytope formulation when uncertainty is present. The approach is tested in a mobile inverted pendulum robotic platform, and the effectiveness is verified in this underactuated and undesensed case.

This review examines the relationship between blackhole activity and kinematic gas-star misalignment in brightest group galaxies (BGGs) with different merger rates. The formation history of galaxy groups is assessed through "age-dating" as an indicator of distinct major mergers involving the BGG. BGGs within groups characterized by a higher frequency of major mergers are more likely to host active SMBHs. A consistent correlation is identified between the level of black hole activity, as indicated by the 1.4 GHz and 325 MHz radio emissions, and the degree of kinematic misalignment between the gas and stellar components in BGGs. In dynamically relaxed groups, where blackhole accretion rate is relatively (∼1 dex) lower due to the lack of recent ( ≤1 Gyr) major mergers, there is reduced (∼ 30%) misalignment between the gas and stellar components of BGGs compared to unrelaxed groups. Additionally, the study reveals that BGGs in unrelaxed groups show higher levels of star formation rate and increased occurrence of mergers, contributing to observed color differences. Exploring the properties and dynamics of the gas disc influenced by mechanical AGN feedback through hydrodynamic simulations suggests that AGN wind-induced effects further lead to persistent gas misalignment of the disk around the supermassive blackhole.

In this research, we present a comprehensive methodology to categorize perfumes based on their fragrance profiles and subsequently aid in creating innovative odoriferous molecules using advanced neural networks. Drawing from data on Parfumo and the Good Scents Company webpage (Parfumo, 2008; The Good Scents Company, 2021), the study employs sophisticated web scraping techniques to gather diverse perfume attributes. Following this, a k-means algorithm is applied for perfume clustering, paving the way for recommending similar scents to consumers. The process then bridges customer preferences to molecular design by incorporating their feedback into generating new molecules via graph neural networks (GNNs). Through converting the Simple Molecular Input Line Entry System (SMILES) representation into graph structures, the GNN facilitates the creation of new molecular designs attuned to consumer desires. The proposed approach offers promising avenues for consumers to pinpoint similar perfume choices, incorporating feedback, and for manufacturers to conceptualize new fragrant molecules with a high likelihood of market resonance.

Background: Alzheimer's disease causes great changes, with the prefrontal cortex be-ing frequently damaged zones, affecting physical and cognitive behavioural and compromising autonomy and quality of life. Objective: To evaluate the effectiveness of feedback-based tech-nology on the improvement of physical-cognitive capacities in Alzheimer. Methods: Forty pa-tients with Alzheimer were recruited from the Santa Elena Alzheimer's Association, Seville, of which 15 ended up being pilot participants, divided randomly into controls (8) and experi-mental (7). They were evaluated with: Cognitive Mini-Examination Scale, Oddball Test and At-tention Network, Berg Scale, Tinetti, Timed up and Go and Geriatric Deterioration Scale. The experimental group was treated with feedback-based technology under the supervision of physiotherapists, during 16 thirty-minute sessions, twice a week. The control group performed their usual care. Result: A significant improvement was observed in the experimental group (Cognitive Mini-Examination and Tinetti). In the group of control, a worsening of physical and motor skills was evidenced because of the degenerative disease. Discussion/Conclusion: This treatment could be a strategy to keep the patient in early stages for longer, and improve quali-ty of life delaying dependency. It creates intergenerational bonds and use at home to promote treatment adherence.

Training data for a deep learning (DL) neural network (NN) controller are obtained from the input and output signals of a conventional digital controller that is designed to provide the suitable control signal to a specified plant within a feedback digital control system. It is found that if the DL controller is sufficiently deep (four hidden layers), it can outperform the conventional controller in terms of settling time of the system output transient response to a unit-step reference signal. That is, the DL controller introduces a damping effect. Moreover, it does not need to be retrained to operate with a reference signal of different magnitude, or under system parameter change. Such properties make the DL control more attractive for applications that may undergo parameter variation, like sensor networks.

Students who had been actively engaged in mediated collaborative activities, were asked for their perceptions about the sustainable peer feedback they had received and provided. Their views were then analyzed and categorized in terms of receiver and provider feedback, cognitive feedback and previously acquired feedback to further knowledge about sustainable education processes. A peer supported feedback questionnaire was created and validated, and its categories were correlated. The questionnaire was then aligned with the activities used to foster peer feedback between the pre-service students from the three bachelor’s degrees. The perceptions the students had of the feedback processes were analyzed using defined peer support feedback categories and the results showed a correlation between cognitive feedback and both provider and receiver self-efficacy feedback. In addition, there was a further correlation between both provider and receiver self-efficacy feedback as well as provider and receiver involvement and feedback structure. However, the results also revealed that neither receiver nor provider autonomy support were significant categories for supportive feedback.

Environmental effects and climate change are lately representing an increasing strain of the coastal areas which topography strongly depends on these conditions. However, the processes by which weather and environmental phenomena influence the highly variable beach morphology are still unknown. A continuous monitoring of the beach environment is necessary to implement protection strategies. This paper presents the results of an innovative study performed on a coastal area using satellite remote sensing data with the aim of understanding how environmental phenomena affect beaches. Two-years of synthetic aperture radar (SAR) Sentinel-1 images are used over a test area in Noordwijk, the Netherlands. At the same time as the SAR acquisitions, information on tidal and weather conditions are collected and integrated from nearby meteorological stations. Dedicated codes are implemented in order to understand the relationship between the SAR amplitude and the considered phenomena: wind, precipitation, tidal conditions. Surface roughness is taken into account. The results indicate a strong correlation between the amplitude and the wind. No particular correlation or trend could be noticed in the relation with the precipitation. The analysis of the amplitude also shows a decreasing trend moving from the dry area of the beach towards the sea and the correlation coefficient between the amplitude and the tide level gets negative with the increase of the water content.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

Grating (moiré) interferometry is one of the well-known methods for full-field in-plane displacement and strain measurement. There are many design solutions for grating interferometers, including systems with a microinterferometric waveguide head. This article proposes a modification to the conventional waveguide interferometer head, enabling the implementation of a polarization fringe phase shift for automatic fringe pattern analysis. The article presents both the theoretical consideration of the proposed solution and its experimental verification, along with the concept of the in-plane displacement/strain sensor using the described head.

The investigation on the issue of damage diagnosis based on strain modal parameters is conducted in this paper using simply supported wooden Beams as the study's object. First, ABAQUS is utilized to create finite element models of intact wooden beams as well as wooden beams with varying degrees of damage and perform modal analyses on them. Next, damage identification studies are conducted on the wooden beam structure using various strain modal parameters (strain mode strain modal difference, strain modal curvature difference), the timber beam damage identification test then yields the modal parameters of timber beams under various damage situations, and the test findings are contrasted with those of the numerical simulation. The outcomes demonstrate that the damage identification of the test data using the three types of damage identification indexes is consistent with the results of the numerical simulation; the three types of damage identification indexes can locate the damage to timber beams, but the identification effect of the indexes is different, the best-recognized metric is the strain mode curvature difference; the next best is the strain mode difference, and the worst is the strain modes. The study's findings can serve as a guide for future damage detection on wood beams.

This work investigates the influence of strain rate on the stress/strain behaviour of Scalmalloy. This material is an aluminium-scandium-magnesium alloy, specifically developed for additive manufacturing. The bulk yield stress of the material processed by Selective Laser Melting is approximately 340 MPa which can be increased by heat-treating to approximately 530 MPa. These numbers, combined with the low mass density of 2.7 g/cm3, make Scalmalloy an interesting candidate for lightweight crash-absorbing structures. As this application is inherently dynamic, it is of interest to study the loading rate sensitivity, which is difficult to predict: Al-Sc alloys exhibit classic strain rate sensitivity with an increased yield stress at elevated strain rates. However, Al-Mg alloys are known to show the contrary effect, they exhibit less strength as strain rate is increased. To answer the question how these effects combine, we study the dynamic behaviour at four different strain rates ranging from 10−3 /s to 1000 /s using servo-hydraulic and Split-Hopkinson testing methods. The resulting data is analysed in terms of strain rate sensitivity of tensile strength and failure strain. A constitutive model based on a simplified Johnson-Cook approach is employed to simulate the tensile tests and provides good agreement with the experimental observations.

Globally, the use of whole-cell matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) in clinical microbiology laboratories has increased considerably. With the rapid growth of artificial intelligence technology, there is an increasing number of areas devoted to solving problems by implementing machine learning-based methods. Applying the use of artificial intelligence to the analysis of the massive amount of information obtained in the mass spectrum derived from MALDI-TOF MS should be a breakthrough in clinical microbiology. Specifically, it would facilitate a more rapid and accurate strain typing or antibiotic susceptibility test (AST) based on whole-cell MALDI-TOF MS spectra, and hence, it is a promising solution. Even though the reproducibility of peaks could result in some critical problems, computational methods have been developed to address this issue. Therefore, clinical microbiologists are able to perform strain typing or an AST as smoothly and easily as identifying species by using MALDI-TOF MS and artificial intelligence.

A highly sensitive strain sensor based on tunable cascaded Fabry-Perot interferometers (FPIs) is proposed and experimentally demonstrated. Cascaded FPIs consist of a sensing FPI and a reference FPI which effectively generate the Vernier Effect (VE). The sensing FPI comprises a hollow core fiber (HCF) segment sandwiched between single-mode fibers (SMFs), and the reference FPI consists of a tunable air reflector, which is constituted by a computer programable fiber holding block to adjust the desired cavity length. Simulation results predict the dispersion characteristics of modes carried by HCF. The sensor’s parameters are designed corresponding to a narrow bandwidth range, i.e., 1530 nm to 1610 nm. Experimental results demonstrate that the proposed sensor exhibits optimum strain sensitivity of 23.9 pm/με in the range of 0 to 3000 με which is 13.73 times higher than the single sensing FPI strain sensitivity of 1.74 pm/με. The strain sensitivity of the sensor can be further enhanced by extending the source bandwidth. The proposed sensor exhibits ultra-low temperature sensitivity of 0.49 pm/°C in the wider temperature range of 25 °C to 135 °C, providing good isolation for eliminating cross-talk between strain and temperature. The sensor is very robust, cost-effective, easy to manufacture, repeatable, and shows a highly linear and stable response in the wider range of axial strain. Based on the sensor’s performance, it may suit plenty of practical applications in the real sensing world

Myxobacteria feature unique biological characteristics including their capability to glide on surface, undergo different multicellular developmental stages and produce structurally unique natural products such as the catecholate-type siderophores myxochelin A and B. Herein, we report the isolation, structure elucidation and biosynthesis of the new congener myxochelin B-succinate from the terrestrial myxobacterial strain MSr12020, featuring a succinyl decoration at its primary amine group. Myxochelin-B-succinate exhibited antifungal growth inhibition and moderate cytotoxic activity against selected human cancer cell lines. This unique chemical modification of myxochelin B might provide interesting insights for future microbiological studies to understand the biological function and biosynthesis of secondary metabolite succinylation.

The stress imposed by ethanol to Saccharomyces cerevisiae cells are one of the most challenging limiting factors in industrial fuel-ethanol production. Consequently, the toxicity and tolerance to high ethanol concentrations has been the subject of extensive research, allowing the identification of several genes important for increasing the tolerance to this stress factor. However, most studies were performed with well characterized laboratory strains, and how the results obtained with these strains work in industrial strains remains unknown. In the present work we have tested three different strategies known to increase ethanol tolerance by laboratory strains in an industrial fuel-ethanol producing strain: overexpression of the TRP1 or MSN2 genes, or overexpression of a truncated version of the MSN2 gene. Our results show that the industrial CAT-1 strain tolerates up to 14% ethanol, and indeed the three strategies increased its tolerance to ethanol. When these strains were subjected to fermentations with high sugar content and cell-recycle, simulating the industrial conditions used in Brazilian distilleries, only the strain with overexpression of the truncated MSN2 gene showed improved fermentation performance, allowing the production of 16% ethanol from 33% of total reducing sugars present in sugarcane molasses. Our results highlight the importance of testing genetic modifications in industrial yeast strains under industrial conditions in order to improve the production of industrial fuel ethanol by S. cerevisiae.

We provide an extensive and systematic investigation of exciton dynamics in droplet epitaxial quantum dots comparing the cases of (311)A, (001) and (111)A surfaces. In spite of a similar s-shell exciton structure common to the three cases, the absence of a wetting layer for (311)A and (111)A samples leads to a larger carrier confinement with respect to (001), where a wetting layer is present. Moreover, this leads to a more pronounced dependence of the binding energies of s-shell excitons on the quantum dot size and to a strong anti-binding character of the positive charged exciton for smaller quantum dots. In-plane geometrical anisotropies of (311)A and (001) quantum dots lead to a large electron-hole fine interaction (fine structure splitting, FSS ~ 100 ueV) whereas for the three-fold symmetric (111)A counterpart this figure of merit is reduced of about one order of magnitude. In all these cases we do not observe any size dependence of the fine interactions. Heavy-hole/light-hole mixing is present in all the studied cases leading to a broad spread of linear polarization anisotropy (from 0 up to about 50%) irrespective of surface orientation (symmetry of the confinement), fine interactions and nanostructure size. These results are important for the further development of ideal single and entangled photon sources based on semiconductor quantum dots.

Bioethanol has been considered as an excellent alternative to fossil fuels since it importantly contributes to the reduced consumption of the crude oil and to the alleviation of environmental pollution [1]. Up to now, the baker yeast Saccharomyces cerevisiae is the most common eukaryotic microorganism used in ethanol production. The inability of S. cerevisiae to grow on pentoses, however, hinders its effective growth on plant biomass hydrolysates, which contain large amounts of C5 and C12 sugars. The industrial-scale bioprocessing requires high temperature bioreactors, diverse carbon sources, and the high titer production of volatile compounds [2]. These criteria indicate that the search for alternative microbes possessing useful traits that meet the required standards of bioethanol production is necessary. Compared to other yeasts, Kluyveromyces marxianus has several advantages over the others, e.g. it could grow on a broad spectrum of substrates (C5, C6 and C12 sugars) [3], tolerate to high temperature, toxin [4,5] and a wide range of pH values [6], and produce volatile short-chain ester [2]. K. marxianus also shows a high ethanol production rate at high temperature and is a Crabtree-negative species [7]. These attributes make K. marxianus a promise as an industrial host for the biosynthesis of biofuels and other valuable chemicals.