Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

This work investigates the influence of strain rate on the stress/strain behaviour of Scalmalloy. This material is an aluminium-scandium-magnesium alloy, specifically developed for additive manufacturing. The bulk yield stress of the material processed by Selective Laser Melting is approximately 340 MPa which can be increased by heat-treating to approximately 530 MPa. These numbers, combined with the low mass density of 2.7 g/cm3, make Scalmalloy an interesting candidate for lightweight crash-absorbing structures. As this application is inherently dynamic, it is of interest to study the loading rate sensitivity, which is difficult to predict: Al-Sc alloys exhibit classic strain rate sensitivity with an increased yield stress at elevated strain rates. However, Al-Mg alloys are known to show the contrary effect, they exhibit less strength as strain rate is increased. To answer the question how these effects combine, we study the dynamic behaviour at four different strain rates ranging from 10−3 /s to 1000 /s using servo-hydraulic and Split-Hopkinson testing methods. The resulting data is analysed in terms of strain rate sensitivity of tensile strength and failure strain. A constitutive model based on a simplified Johnson-Cook approach is employed to simulate the tensile tests and provides good agreement with the experimental observations.

This study investigates the microstructures and deformation mechanism of hetero-structured pure titanium under different high strain rates (500 s-1，1000 s-1，2000 s-1). The influence of strain rate on the deformation mechanism is examined. As the strain rate increases, the dominance of dislocation slip decreases while deformation twinning becomes more prominent. Notably, at a strain rate of 2000s-1, nanoscale twin lamellae are activated within grain with a size of 500nm, which is a rarely observed phenomenon in pure Ti. Additionally, martensitic phase transformation is also identified. These findings can greatly enhance our understanding of the mechanical responses of Ti and broaden the potential applications of Ti in dynamic deformation scenarios.

In this study, we investigate the influence of control type and strain rate on the lifetime of specimens manufactured from 50CrMo4. This influence is described by a strain rate dependent method that uses cyclic stress strain curves to correct displacement controlled cyclic test results. The objective of this correction is to eliminate the stress related differences between displacement controlled cyclic test results and force controlled cyclic test results. The method is applied to the results of ultrasonic fatigue tests of six different combinations of heat treatment, specimen geometry (notch factor) and atmosphere. The corrected results show an improved agreement with test results obtained on conventional fatigue testing equipment with similar specimens: the standard deviation in combined data sets is significantly reduced (p=4.1%). We discuss the literature on intrinsic and extrinsic strain rate effects in carbon steels.

The effect of the strain rate on damage in carbon black filled EPDM stretched during single and multiple uniaxial loading is investigated. This has been performed by analysing the stress-strain response, the evolution of damage by Digital Image Correlation (DIC), the associated dissipative heat source by InfraRed thermography (IR), and the chains network damage by swelling. The strain rates were selected to cover the transition from quasi-static to medium strain rate conditions. In single loading conditions, the increase of the strain rate yields in a preferential damage of the filler network while rubber network is preserved. Such damage is accompanied by a stress softening and an adiabatic heat source rise. Conversely, increasing the strain rate in cyclic loading conditions yields in a filler network accommodation and a high self-heating whose combined effect is proposed as a possible cause of the ability of filled EPDM to limit damage, by reducing cavities opening during loading and favoring cavities closing upon unloading.

This contribution was devoted to unveil the strain rate sensitivity (SRS) of G18NiCrMo3-6 cast steel in tension/compression asymmetry. For that purpose, detailed mechanical characterization tests were conducted providing a process window covering quasi-static and medium strain rate regimes (0.001, 0.1, 10 [ s¯¹]) in tension and compression states. By means of this experimental ef-fort, the SRS of the material could be extracted by a function of strain and strain rate which ena-bling to create a mathematical expression to easily be implemented as a state variable for constitu-tive material modeling. Finally, a pressure and rate dependent constitutive material model on the basis of Cocks'89 yield locus definition was created by a subroutine (UMAT) file and the material parameters were verified with respect to the experimental data. The UMAT file also takes into account the tension/compression asymmetry in yielding to handle the effect of porous media plas-ticity concept. The predictions of the proposed material model are quite in line with the experi-mental outputs.

Tomato brown rugose fruit virus (ToBRFV) is a causal agent of severe emergent diseases in Solanaceae hosts with agronomic relevance, such as tomato and pepper. Herein, we analyzed the seed transmission rate and efficacy of different seed disinfection treatments and performed a comparison of molecular biology techniques seeking rapid and sensitive detection in seed lots. We evaluated several total RNA extraction and RT-PCR protocols using a distinct combination of PCR primers to test for the presence of the ToBRFV Mexican strain in tobacco host. Our results showed that the percentage of seed and seedlings transmission was less than 1% and that a 3% sodium hypochlorite solution was effective as a seed disinfection treatment. Finally, the most sensitive molecular method identified for virus detection consisted of a CTAB-Trizol RNA extraction followed by nested PCR using primers reported by Dovas et al. (2004). Additionally, we tested potential natural hosts in selected Cucurbitaceae and Solanaceae species. Our results showed that the ToBRFV Mexican strain is capable of experimentally infecting eggplant (Solanum melongena), tomatillo (Physalis ixocarpa), and tobacco (Nicotiana rustica).

This review delves into the growing field of flexible and stretchable strain sensors utilized in human gait analysis, focusing on determining knee bending angle and muscle activities when a human subject walks. Recent advancements have enabled these sensors to accurately capture biomechanical parameters while accommodating the body's natural movements. We examine the principles underlying these sensors' design and fabrication techniques, emphasizing their flexibility, stretchability, and biocompatibility for seamless integration into wearable systems. Through critical evaluation of existing methodologies, we assess the reliability and validity of these sensors in quantifying gait parameters. Furthermore, we discuss this technology's clinical and research implications, highlighting its potential in personalized rehabilitation and sports performance optimization. We provide an overview of flexible strain sensors and their application for analyzing human walking gait, especially for observing walking gait in rehabilitation programs. First, we present the basic working principles of various flexible strain sensors. Second, by the application of flexible strain sensors as walking gait monitoring. Finally, current challenges and future opportunities in this research area are discussed. By synthesizing current knowledge and outlining future directions, this review aims to provide insights for researchers and practitioners seeking to leverage flexible and stretchable strain sensors for comprehensive human gait analysis.

The flow stress of face-centered cubic (FCC) metals exhibits a rapid increase near a strain rate of 104 s-1 under fixed strain conditions. However, many existing constitutive models either fail to capture the mechanical characteristics of this plastic deformation or use piecewise strain rate hardening models to describe this phenomenon. Unfortunately, the piecewise models may suffer from issues such as discontinuity of physical quantities and difficulties in determining segment markers, and struggling to reflect the underlying physical mechanisms that give rise to this mutation phenomenon. In light of this, this paper proposes that the abrupt change in flow stress sensitivity to strain rate in FCC metals can be attributed to microstructural evolution characteristics. To address this, a continuous semi-empirical physical constitutive model for FCC metals is established based on the microstructural size evolution proposed by Molinari-Ravichandran and the dislocation motion slip mechanism. This model effectively describes the mutation behavior of strain rate sensitivity under fixed strain, particularly evident in the annealed OFHC. The predicted results of the model across a wide range of strain rates (10-4 − 106 s-1) and temperatures (77 − 1096 K) demonstrate relative errors generally within ±10% of the experimental values. Furthermore, the model is compared to five other models, including Mechanical Threshold Stress (MTS), Nemat-Nasser-Li (NNL), Preston-Tonks-Wallace (PTW), Johnson-Cook (JC), and Molinari-Ravichandran (MR) models. A comprehensive illustration of errors reveals that the proposed model outperforms the other five models in describing the plastic deformation behavior of OFHC. The error results offer valuable insights for selecting appropriate models for engineering applications and provide significant contributions to the field.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

Background and Objectives: High job strain is worsening the outcome in coronary artery disease, CAD. Severe dissatisfaction on workplace, imbalance between high demands , and low rewards, are affecting the quality of life, and diminishing the duration of life, especially in CAD patients. Our study included two samples : CAD patients (experimental group), and without CAD patients, but with traditional risk factors (control group). The main objective of the study was the role played by high sensitivity C reactive protein, hs CRP, and microalbuminuria, as mediators of job strain and CAD relationship. Secondary objectives were the following: identification of the most vulnerable patients( with significant job strain) and intervention towards this category, for cardiovascular events prevention (primary or secondary). Materials and Methods: The utilized methods were the following : clinical exam; electrocardiogram; echocardiogram; non contrast enhanced computed chest tomography; laboratory findings ( lipid profile, glycemia, hs CRP, microalbuminuria); type D scale, DS 14; depression questionnaire, PHQ-9; and satisfaction with work scale, SWWS. Results: The highest values for hs CRP and microalbuminuria were noticed in patients with the lowest Likert score, for both samples CAD, and without CAD patients. The highest job strain was noticed in females. More than half of CAD patients ,with low Likert scores, revealed myocardial infarction. Conclusions: Microalbuminuria and hs CRP were statistical significant in the study as intercessors, in job strain and CAD relationship. The most vulnerable patients for vascular events were females, in both groups : CAD and “CAD waiting desk”. In CAD sample, the vascular vulnerability was also increased by high job strain.

This article presents a new input device for spastic patients and others with similar symptoms. The sensor consists of a disc used to determine positions and can replace standard joysticks in medical devices such as electric-powered wheelchairs. Using a standard joystick while operating a powered wheelchair can result in dangerous situations when spastic movements occur and extremities cramp making them uncontrollable. To avoid this, a disc was developed that can be controlled with any body part. By shifting weight (x- and y-axis) the disc can tilt in any direction creating a proportional output signal and can also be pushed down in the center (z-axis) to open a menu on a screen for example. When spasms occur it is impossible for users to get stuck on the input device because the disc is flat and can be mounted within a control panel. Body parts coming into contact with the disc would merely slide across the disc without triggering unintentional actions. The sensor presented here is also adaptive and can be adjusted to fit a user’s strength and range of motion. This proposal aims to develop an input device that enables spastic patients to operate sensitive systems safely.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

One challenging problem is the representation of three-dimensional datasets that vary with time. These datasets can be though as a cloud of points that gradually deforms. But point-wise variations lack of information about the overall deformation pattern, and more importantly, about the extreme deformation locations inside the cloud. The present article applies a technique in computational mechanics to derive the strain-rate state of a time-dependent and three-dimensional data distribution, by which one can characterize its main trends of shift. Indeed, the tensorial analysis methodology is able to determine the global deformation rates in the entire dataset. With the use of this technique, one can characterize the significant fluctuations in a reduced multivariate description of an urban system and identify the possible causes of those changes: calculating the strain-rate state of a PCA-based multivariate description of an urban system, we are able to describe the clustering and divergence patterns between the districts of the city and to characterize the temporal rate in which those variations happen.

The holistic approach of One Health, which sees human, animal, plant, and environmental health as a unit, rather than discrete parts, requires not only interdisciplinary cooperation, but standardized methods for communicating and archiving data, enabling participants to easily share what they have learned and allow others to build upon their findings.Ongoing work by NCBI and the GenomeTrakr project illustrates how open data platforms can help meet the needs of federal and state regulators, public health laboratories, departments of agriculture, and universities. Here we describe how microbial pathogen surveillance can be transformed by having an open access database along with Best Practices for contributors to follow. First, we describe the open pathogen surveillance framework, hosted on the NCBI platform. We cover the current community standards for WGS quality, provide an SOP for assessing your own sequence quality and recommend QC thresholds for all submitters to follow. We then provide an overview of NCBI data submission along with step by step details. And finally, we provide curation guidance and an SOP for keeping your public data current within the database. These Best Practices can be models for other open data projects, thereby advancing the One Health goals of Findable, Accessible, Interoperable and Re-usable (FAIR) data.

Probiotic feed additives have attracted considerable research interest in recent years because the effectiveness of probiotics can differ across microbial strains and the supplemented macroorganisms. The present study was conducted on 16 lambs divided into two groups (C - control and E - experimental). The examined lambs were aged 11 days at the beginning of the experiment and 40 days at the end of the experiment. The diet of group E lambs was supplemented with a multi-strain probiotic formulation (Lactobacillus plantarum AMT14, Lactobacillus plantarum AMT4, Lactobacillus rhamnosus AMT15, and Bifidobacterium animalis AMT30), whereas group C lambs did not receive the probiotic additive. At the beginning of the experiment (day 0) and on experimental days 15 and 30, blood was sampled from the jugular vein to determine and compare: phagocytic activity (PHAGOTEST) and oxidative metabolism (PHAGOBURST) of peripheral blood granulocytes and monocytes by flow cytometry. An analysis of the phagocytic activity of granulocytes and monocytes revealed significantly higher levels of phagocytic activity (expressed as the percentage of phagocytic cells and mean fluorescence intensity) in lambs administered the multi-strain probiotic formulation than in the control group. The probiotic feed additive also exerted a positive effect on the oxidative metabolism of both granulocytes and monocytes (expressed as the percentage of oxidative metabolism and mean fluorescence intensity) after stimulation with Escherichia coli bacteria and with PMA (4-phorbol-12-β-myristate-13-acetate).

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

Abstract: A. baumannii exhibits resilience in harsh environments and progressively develops resistance to diverse antibacterial agents over time. This adaptability poses a significant challenge in treating an infection caused by this bacterium within healthcare settings. The presence of peptidoglycan, a crucial precursor for cell wall synthesis, contributes to this challenge. Peptidoglycan serves not only as a structural support in bacterial cells but also provides protection against adverse environmental conditions. The synthesis of the peptidoglycan layer involves a group of substrates such as N-acetylglucosamine (GlcNAc) and N-acetylmuramic acid (MurNAc), within a three-partitioned process occurring in the membrane, periplasmic space, and cytoplasm of each bacterium. Initiated in the cytoplasm and extending to the inner cell membrane, this synthesis starts with the production of nucleotide precursors. The first step involves the synthesis of UDP-GlcNAc, orchestrated by Glm (GlmS, GlmM, and GlmU) enzymes using fructose-6-phosphate. Subsequently, enzymes from the Mur family, namely MurB, MurA, MurD, MurC, MurI, MurF, and MurE, synthesize UDP-N-acetylmuramyl-pentapeptide (UDP-Mpp) from UDP-GlcNAc. Concurrently, on the cytosolic side, the production of membrane-surrounded undecaprenyl phosphate occurs, involving membrane-side proteins MraY and MurG in the biosynthesis of peptidoglycan. This review emphasizes updated information on Mur family proteins, encompassing physicochemical properties, nature of binding site, number and type of binding site residues, functional domain details, three-dimensional structural aspects, and their functions within bacterial cells. Special attention is directed towards their enzymatic role in peptidoglycan biosynthesis due to the limited availability of precursors in the market. Additionally, the review provides a comprehensive summary of existing inhibitors and ongoing efforts in identifying new targeted inhibitors, recognizing these enzymes as potential candidates for antibacterial drug design and discovery.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

1) Background: Ultrasound-based strain imaging is now available in several ultrasound (US) scanners. Strain ratio (SR) can be used to quantify strain recorded simultaneously in two different user-selected areas, ideally exposed to the same amount of stress. The aim of this study was to evaluate SR variability when assessed in an in-vitro setup with a tissue-mimicking phantom, on resected tissue samples and in live tissue scanning with endoscopic applications. 2) Material and methods: Retrospective analysis of SR for quantification of elastic contrasts in a tissue-mimicking phantom containing four homogenous inclusions, in 38 resected bowel wall lesions and in 48 focal pancreatic lesions examined in vivo. Median SR and the inter-quartile range (IQR) was calculated on all external and endoscopic US-applications. The IQR/median provides a measure of the SR variability focusing on the two percentiles of the data closest to the median value. 3) Results: The overall variability of SR was lowest in a tissue-mimicking phantom (mean QR/median SR: 0.07). In resected bowel wall lesions representing adenomas, adenocarcinomas or Crohn lesions, the variability increased (mean IQR/Median: 0.62). During an endoscopic examination of focal pancreatic lesions in vivo, the variability increased further (mean IQR/Median: 2.04). 4) Conclusion: SR variability increased when assessed on different targets with growing heterogeneity and biological variability as one moved from homogeneous media to live tissues and endoscopic application. This may indicate a limitation for the accuracy SR evaluation in clinical applications.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P&lt;0.05), left hippocampus volume (LHV, β: -0.02435, P&lt;0.01) and right hippocampus volume (RHV, β: -0.02544, P&lt;0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P&lt;0.05) and LHV (β: -0.01173, P&lt;0.05) and RHV (β: -0.01193, P&lt;0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P&lt;0.05; RHV, β: -0.005527, P&lt;0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

: To improve the efficiency of rhizobial inoculation operations and address the current situation of rhizobial inoculation being labor-intensive, a spraying and control system for variable rate application (VRA) of liquid rhizobia was developed. The system can accurately regulate the spraying rate of liquid rhizobia according to the desired rate of rhizobia by incremental Proportional Integral Derivative (PID) closed-loop control algorithm, making it particularly suitable for precise spraying with small amounts. In the laboratory experiment of precise flow control, variation coefficient of spraying nozzle from 0.10 MP to 0.20 MP pressure were no more than 1.2%. A clear linear relationship was observed between the spraying rate and pressure. The maximum response time was 1.93 seconds, while the average response time was 1.62 seconds when controlling the spraying system for small amounts. Field trial was conducted in Heilongjiang Agricultural Xianghe Farm of China. Average seeds number and 100-seed weight of soybean plant with rhizobia inoculation treatment were better than control group, and average yield of spraying liquid rhizobia agent with full base fertilizer increased by 232.5 kg/hm2, representing a significant 7.4% improvement over the control group. The results of these trails clearly showed the positive effect of the spraying and control system for liquid rhizobial inoculation, which has superior to existing inoculation manners, and provides an important technical support for the widespread adoption of rhizobia technology.

This research work has been based on a previous study by the authors that characterized the behavior of a polyimide-coated FBG sensor in a structural monitoring system. Sensors applied to structural health monitoring are affected in the presence of a state of multidirectional strains simultaneously. The previous study observed the influence of transverse strain (ε_y) while keeping longitudinal strain constant (ε_x), where the direction x is the direction of the optical fiber. The present study developed an experimental methodology which has consisted of carrying out a campaign of biaxial tests on cruciform specimens with three embedded FBG sensors coated with polyimide, acrylate and ORMOCER®. Applying the Strain–Optic Theory as reference, a comparison of the results obtained with the different coatings has been studied. This experimental work has done it possible to study the influence of transverse strain (ε_y) in the longitudinal measurement of each of the FBG sensor and the influence of the coating material. Finally, the calibration procedure as well as the strain sensitivity factor K for each sensor has been defined.

We report a simple and high-performance flexible strain sensor based on liquid metal nanoparticles (LMNPs) on polyimide substrate by laser induced deposition. The LMNPs were prepared by ultrasonic method, and then the femtosecond laser direct writing technology was used to induce the assembly and deposition of the LMNPs to form liquid metal microwires. Laser local sintering enhances the connection between particles, and a wearable strain sensor was fabricated with the high sensitivity as high as 76.18, the good linearity (a correlation coefficient of 0.999) in a wide sensing rage, the fast response/recovery time of 159 ms/120 ms. Attributed to these extraordinary strain sensing performances, the sensor can sense various dynamic strains in real time, monitor both subtle physiological activities and large human motions. It can be adhered to human skin, and well reflect the change of facial expression and realize real-time monitoring of facial expression. And the vocal cord vibration can be detected for speech recognition while the sensor attached to the outside of the throat.

The emergence of drug resistant pathogenic bacteria is increasingly challenging conventional antibiotics. Plant derived flavonoids are considered as potential alternatives to antibiotics due to their antimicrobial properties. However, the mechanisms by which flavonoids modulate pathogenic microorganisms’ growth are not fully understood. In our previous studies we found that Rutin, a kind of flavonoids showed inhibition against Klebsiella pneumoniae strains. In order to better understand its inhibitory mechanism on strain growth, we used both Rutin and Luteolin as treatments to incubate K. pneumoniae ATCC700603 strain. After incubation for 4 hours, the homogenous and differential effects of two different flavonoids on the growth of K. pneumoniae were evaluated. The integrated metabolomic and transcriptomic analysis was performed. The expression levels of 5,483 genes and the contents of 882 metabolites were measured. The differentially expressed genes (DEGs) and metabolites (DEMs) were screened and analyzed. The correlation between DEGs and DEMs were also studied. Our results showed that Rutin could inhibit the strain growth by changing metabolic pathways and ABC transporters pathways. Our study also revealed FU841_RS17580 and FU841_RS19145 as functional genes that played vital roles in the strain growth.

In this study the impact of terrorist attacks on exchange rate is estimated. Particularly, the study focuses on Turkish terrorist attacks and its implication on Turkish lira versus pound sterling exchange rate. In order, to find the causal effect the study employed Autoregressive distributive lag (ARDL) bound testing approach as an estimation technique. Accordingly, the analysis reveals that terrorist attack has a negative impact on the exchange rate in both short and long-run. However, the negative effect of terrorism tends to be small in both the short-run and long-run. More precisely, terrorist attack depreciates the exchange rate between Turkish lira and pound sterling by approximately 0.00072 in the next trading day. The long-term effect also shows that terrorist attack depreciates the exchange rate on average by 0.00212.

Recently, research on ultra-high-performance concrete (UHPC) with the characteristics of ultra-high strength, high toughness, and high durability has been actively conducted from materials to actual structural applications. However, research on experimental methods that reflect the unique characteristics of UHPC, which are different from those of normal concrete, is insufficient. To solve the difficulties in applying the compressive creep test method for normal concrete to UHPC and to verify the validity of the recently proposed ASTM C 1856 standard test method, this study performed compressive creep tests on UHPC with variables of specimen size, sustained load intensity, fiber length, and strain measuring method. Two types of cylindrical specimens of ϕ100 × 200 mm and ϕ75 × 150 mm were used for a specimen size variable. The sustained load intensities of 10% to 40% based on the specified compressive strength of 150 MPa were applied. Two types of steel fiber lengths of 13 mm and 19.5 mm in the UHPC mix were used as a variable, and three strain measuring methods of the embedded strain gauge method, the attached strain gauge method, and the strain meter with stud measured the change in length of the UHPC specimens. The experimental results showed that the strain meter method using the standard rod had limitations due to the error in the verification process using the standard rod and the observation error of the measurer, and the sustained load intensity is preferable to 15% to 40% of the actual compressive strength. It was found that it is possible to perform a compressive creep test for UHPC using a specimen with a size of ϕ75 mm or more, and the fiber length did not affect the creep behavior of UHPC up to 19.5 mm. As a result of comparing the UHPC creep test results with the creep prediction model, the B3 model was found to most accurately predict the UHPC creep behavior. The creep coefficient pattern of the B3 model was very similar to the measured results, and well reflected the effects of the mixing ratio and compressive strength of UHPC.

One of the factors in the mobility of a nation's economy is the stock exchange which plays a decisive role in sustainable economic development. Accordingly, and for the special place of the stock exchange in the economy, we decided to investigate the relationship between the interest and exchange rates and the Tehran stock exchange dividend and price index (TEDPIX). Using the autoregressive distributed lag method, the present study is conducted utilizing the annual data over the period of 1991 to 2020. The results indicate that the exchange rate has a positive long-run relationship with the TEDPIX, but no statistically significant relationship was found between the TEDPIX and the interest rate. Furthermore, the results of the estimation of the error correction model show that 30.786% of the disequilibrium in each period is adjusted to the long-run equilibrium.

Environmentally friendly and low-cost sensors are needed for the next generation disposable electronics applications. Given its low-cost, availability and biodegradability, paper-based devices are a very promising. Here we demonstrate the fabrication of a tungsten disulphide (WS2) strain sensor on standard copy paper. The WS2 is deposited through direct abrasion of WS2 powder against the paper surface making the fabrication of the device low-tech and cost effective. The fabricated strain gauge devices present gauge factors up to ~70 for strains in the ± 0.5 % range. These values are ~ 9 times larger than that obtained on devices with the same geometry but using a graphite film instead a WS2 as a sensitive material. We demonstrate the potential of these WS2-on-paper strain gauges by integrating them directly on a paper cantilever to sense mass and forces. We show how this very simple device can detect sub-milligram masses. Moreover, we also demonstrate the capability of transducing motion in mechanical resonators by gluing a WS2-on-paper strain gauge on their surface.

Over the last two decades, a considerable amount of equipment has been acquired (spreaders, seeders, sprayers, among others) to respond to the challenges of Precision Agriculture (PA) concept. Most of this equipment has been purchased at a high cost. However, many of them, despite still being functional and equipped with sensors, actuators, and electronic processing units capable of adjusting to variations in speed, have become obsolete in terms of communication, and incompatible with new monitoring and control systems based on the “Isobus” protocol. This work aims to present a solution for updating the control system (“Ferticontrol”) of a “Vicon RS-EDW” spreader with variable rate application (VRA), making it compatible with the “InCommand” system from “Ag Leader”. The solution includes low-cost “Arduino” and “Raspberry Pi” microcontrollers and open-source software. The development shows that it is possible to implement a solution that is accessible to farmers in general. It also provides a niche business opportunity for young researchers to set up small technology-based enterprises associated with universities and research centers. These partnerships guarantee permanent innovation and represent a decisive step towards modern, technological, competitive, and sustainable agriculture.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

(1)Background:The purpose of the study was conducted to investigate the recovery of heart rate according to the performance level and rest interval conditions during 65%1RM bench press exercise;(2)Methods:The subjects of this study were eight healthy male college studentsin their 20 (years) attending University C. 1RM was measured before theexperiment, and the exercise sequence of six rest intervals (30sec, 1, 2, 3, 4,5min) was randomly selected and cross-distribution experiment. The experimental measurement was conducted a total of six times according to the rest interval condition (six conditions) once every 3 days to minimize the learning effect. The data was verified with repeated measures Two-way ANOVA and Contrast's repeated method was applied for post-comparison;(3)Results: First, the amount of exercise and the number of repetitions statistically substantially dropped (p&lt;.001) as the number of sets rose, and a greater decline was shown when the rest periods got shorter. Second, the heart rate after exercise was increased significantly (p&lt;.01) as the set progressed in the long rest interval conditions (4, 5min), and the heart rate after rest was increased statistically significantly (p&lt;,05) as the set progressed in the short rest interval conditions (30sec, 1min). Third, the heart rate recovery rate (%) was able to perform more repetitions than in the short rest interval condition due to the relatively high physiological recovery of the neuromuscular and circulatory system under the long rest interval condition;(4)Conclusions: Therefore, according to the rest conditionduring the 65%1RM bench press exercise conducted in this study, the restinterval condition of 2~3min may be effective in improving muscular endurance,and the rest interval condition of 4~5min may be effective in improving muscular hypertrophy. As a result of this study, there was a significant difference in exercise performance (repetition) and physiological recovery depending on the rest interval condition according to the set progress during the same intensity resistance exercise. Through this, it is judged that it is possible to adjust the amount of exercise appropriate for the purpose of training by adjusting not only the intensity during resistance exercise but also the rest interval between sets.

The paper proposes a mechanism for the impact of changes in the key rate on the volume of newly issued loans. The volume depends on the price (interest rates on loans), and the price depends on the key rate and the actual consumption of loans in the previous period (generalized cobweb cycle). The model was estimated by a Kalman filter, adequacy was confirmed by simulation. It is possible to forecast the average rate on loans for a month in advance according to the information published by the Central Bank of the Russian Federation (CB). By playing various scenarios for changing the key rate, it was found that in quiet periods of economic development, the usual laws of supply and demand operate in the loan market and by raising the key rate, you can reduce inflation. In the turbulent (overheated) state of the economy, an increase in the key rate can, on the contrary, provoke an increase in the issuance of loans and unconventional manipulations with the key rate are required.

Average of 41,900 patients are diagnosed annually with staphylococcus bacterial infection in California, 24,089 patients have Methicillin-resistant Staphylococcus Aureus (MRSA) and 17,810 patients have Methicillin-Sensitive Staphylococcus (MSSA). This paper demonstrates that there is a difference in mortality rate due to staphylococcus infection between males and females (P-value<0.05, CI 95%). Male patient diagnosed with S. aureus has 1.3 chance of mortality incidence than female patient. In addition, MRSA infection rate is 1.4 times MSSA infection (P-value<0.05, CI 95%), but the gap of infection is decreasing; however, mortality of both infections combined are more than threefold greater compared to three decades ago.

In real financial markets, the certainty equivalent rate is an important factor for investors to consider. From the value of a specific company’s certainty equivalent rate, investors can judge if this company is worth investing in. In this paper, we will explore how to obtain the value of the certainty equivalent rate so that we can evaluate a given company. First, we will introduce the theoretical support of this paper, which is put-call parity. From put-call parity, we will derive the mathematical expression for the certainty equivalent rate. Second, we will use the mathematical expression for the certainty equivalent rate to perform an empirical study. We will consider some extreme examples, including some of the best- and worst-performing stocks up to this point in 2023. Based on these stocks’ data, we will visualize the performance of these stocks and explain the meaning of the data. Finally, we will apply the results to a very popular industry—the electric vehicle industry—to explore the current electric vehicle market situation in the U.S.A.

This paper aims to quantify the influence of hydrogen embrittlement on Wierzbicki and Xue (W-X) model parameters. This model has 4 parameters which have been obtained by tensile tests on smooth specimens, tensile notch specimens, single notch tensile specimens (SENT) and pure shear specimens. Hydrogen embrittlement has been obtained by electrolytic method. Application of the (W-X) model has been done to get the local resistance used to predict failure by the Volumetric Method (VM). An example is given for the case of an embedded pipe submitted to service pressure and lateral seismic displacement. The effect of this displacement is then assimilated to the shearing of the straight section of the pipe. The pipe shows a corrosion defect considered a semi-elliptical crack. The influence of hydrogen embrittlement on local strain resistance and safety factors is discussed.

In recent years, two-dimensional (2D) materials have attracted significant attention due to their distinctive properties, including exceptional mechanical flexibility and tunable electronic properties. Via the first-principles calculation, we investigate the effect of strain on the electronic properties of monolayer SnP2S6 and GeP2S6. We find that monolayer SnP2S6 is an indirect band gap semiconductor, while monolayer GeP2S6 is a direct band gap semiconductor. Notably, under uniform biaxial strains, SnP2S6 undergoes an indirect-to-direct band gap transition at 4.0% biaxial compressive strains, while GeP2S6 exhibits a direct-to-indirect transition at 2.0% biaxial tensile strain. The changes of the conduction band edge can be attributed to the high-symmetry point Γ being more sensitive to strain than K. Thus, the relocation of the conduction-band and valence-band edges in monolayer SnP2S6 and GeP2S6 induces a direct-to-indirect and indirect-to-direct band-gap transition respectively. Consequently, the strain is an effective band engineering scheme which is crucial for the design and development of next-generation nanoelectronic and optoelectronic devices.

Cannabidiol (CBD) is a non-intoxicating compound extracted from Cannabis sativa, showing antidepressant-like effects in different rodent models. However, inconsistent results have been described depending on the species and the strain used to assess depressive-like behaviour. Moreover, only a few studies have investigated the effect of CBD in female rodents. Therefore, we aimed to i) investigate the effects of CBD in two different strains of mice (Swiss and C57BL/6) and in a rat model of depression based on selective breeding (Flinders Sensitive and Resistant Lines, FSL and FRL) subjected to tests predictive of antidepressant-like effects; and ii) investigate the influence of sex in the effects of CBD in both mice and rats. CBD induced an antidepressant-like effect in male Swiss but not in female Swiss or C57BL/6 mice in the tail suspension test (TST). In male FSL rats, CBD produced an antidepressant-like effect one-hour post-injection. However, in female FSL, CBD induced a bimodal effect, increasing the immobility time at one hour and decreasing it at two hours. Ketamine produced an antidepressant-like effect in male and female FSL rats at different doses. In conclusion, strain, sex, and administration time affect CBD's behavioural response to rodents exposed to tests predictive of antidepressant effects.

Polydimethylsiloxane (PDMS) is one of the most popular elastomers and has been used in different fields, especially in biomechanics research. Among the many interesting features of this material, its hyperelastic behaviour stands out, which allows the use of PDMS in various applications, like the ones that mimic soft tissues. However, the hyperelastic behaviour is not linear and needs detailed analysis, especially the characterization of shear strain. In this work, two approaches, numerical and experimental, were proposed to characterize the effect of shear strain on PDMS. The experimental method was implemented as a simple shear testing associated with 3D digital image correlation and was made using two specimens with two thicknesses of PDMS (2 and 4 mm). A finite element software was used to implement the numerical simulations, in which four different simulations using the Mooney-Rivlin, Yeoh, Gent, and Polynomial hyperelastic constitutive models were performed. These approaches showed that the maximum value of shear strain occurred in the central region of the PDMS, and higher values emerged for the 2 mm PDMS thickness. Qualitatively, in the central area of the specimen, the numerical and experimental results have similar behaviours and the values of shear strain are close. For higher values of displacement and thicknesses, the numerical simulation results move further away from experimental values.

Structural displacement is an important metric for assessing structural conditions because it has a direct relationship with the structural stiffness. Many bridge displacement measurement techniques have been developed, but most methods require fixed reference points in the vicinity of the target structure which limits field implementations. A promising alternative is to use reference-free measurement techniques that indirectly estimate the displacement by using measurements such as acceleration, and strain. This paper proposes novel reference-free bridge displacement estimation by the fusion of single acceleration with pseudo-static displacement derived from co-located strain measurements. First, we propose a conversion of the strain at the center of a beam into displacement based on the geometric relationship between strain and deflection curves with reference-free calibration. Second, an adaptive Kalman filter is proposed to fuse the displacement generated by strain with acceleration by recursively estimate the noise covariance of displacement from strain measurements which is vulnerable to measurement condition. Both numerical and experimental validations are presented to demonstrate the efficiency and robustness of the proposed approach.

We have developed deep learning models for automatic identification of the maternal heart rate (MHR) and, more generally, false signals (FSs) on fetal heart rate (FHR) recordings. The models can be used to preprocess FHR data prior to automated analysis or as a clinical alert system to assist the practitioner. Three models were developed and used to detect (i) FSs on the MHR channel (the FSMHR model), (ii) the MHR and FSs on the Doppler FHR sensor (the FSDop model), and (iii) FSs on the scalp ECG channel (the FSScalp model). The FSDop model was the most useful because FSs are far more frequent on the Doppler FHR channel. All three models were based on a multilayer, symmetric, GRU and were trained on data recorded during the first and second stages of delivery. The FSMHR and FSDop models were also trained on antepartum recordings. The training dataset contained 1030 expert-annotated periods (mean duration: 36 min) from 635 recordings. In an initial evaluation of routine clinical practice, 30 fully annotated recordings for each sensor type (mean duration: 5 h for MHR and Doppler sensors, and 3 h for the scalp ECG sensor) were analyzed. The sensitivity, positive predictive value (PPV) and accuracy were respectively 62.20%, 87.1% and 99.90% for the FSMHR model, 93.1%, 95.6% and 99.68% for the FSDop model, and 44.6%, 87.2% and 99.93% for the FSScalp model. We built a second test dataset with a more solid ground truth by selecting 45 periods (lasting 20 min, on average) on which the Doppler FHR and scalp ECG signals were recorded simultaneously. Using scalp ECG data, the experts estimated the true FHR value more reliably and thus annotated the Doppler FHR channel more precisely. The models achieved a sensitivity of 53.3%, a PPV of 62.4%, and an accuracy of 97.29%. In comparison, two experts (blinded to the scalp ECG data) respectively achieved a sensitivity of 15.7%, a PPV of 74.3%, and an accuracy of 96.91% and a sensitivity of 60.7%, a PPV of 83.5% and an accuracy of 98.24%. Hence, the models performed at expert level (better than one expert and worse than the other), although a well-trained expert with good knowledge of FSs could probably do better in some cases. The models and datasets have been included in the Fetal Heart Rate Morphological Analysis open-source MATLAB toolbox and can be used freely for research purposes.

The metrological performance of FBG strain sensing systems is a critical premise for the precision of plastics water support pipeline structural deformation measurement, but the strain transfer loss of FBG attached on the plastics pipe subjected by dynamic force is unclear. This paper presents the first study on the effects of strain transfer between FBG, and acrylate polymer blended with poly resin (ABR)pipe sheets loaded by static and dynamic force. Theoretical methods of dynamic strain transfer theory combine with the exponentially decaying sinusoidal shock force time course is deduced and various dynamic parameters sensitivities studies are carried out, as well as that of the geometric parameters. The result of the dynamic theory is compared with the calibration test outcomes, while the ASTR of FBG attached on ABR sheet is compared with distributed optical fiber sensors (DOFS) and other pipe materials such as PVC, concrete, and steel. Results show that the ASTR of FBG is more accurate than that of the DOFS, and the grows of ASTR depending on the paste length of FBG, the Young's modulus of the middle materials, the thickness of the middle materials and attenuation coefficient. Paste length produced the largest increase, yet the magnitude and loading speed of the external force has unexpectedly little effect on ASTR. FBG seem low error, insensitive with dynamic force and independent with the material of matrix, and this demonstrates benefits that are stronger across the board than DOFS. This is not currently recognized by standards or by most reported studies.

Different values of the Hubble constant for extragalactic objects are not considered here. We give a number of examples of the extreme accordance of expansion rates of different fields of knowledge with the cosmological expansion rate. The coincidence of the expansion rates means that a common cause is almost inevitable. All these examples are gravitationally bound in themselves and in this case are subject to cosmological expansion. According to standard theory, this should not happen. We therefore question the common boundary of gravity and expansion for both theoretical and observational reasons and conclude that all gravitationally dominated objects participate in cosmological expansion or scale drift, contrary to general doctrine. The space expands with its contents while numerically maintaining distance, radius, rotation time and density. What is generally interpreted as an expansion is obviously a scale drift with a drift rate that corresponds to the size of the Hubble constant. The Earth is subject to expansion and scale drift. This results in numerically constant measured values. This drift apparently also applies to distant galaxies and other objects. The cosmological red shift is not interpreted here as a Doppler effect and numerical increase in distances, but in accordance with standard theory as an expansion or drift of the space-time scale. The expansion of the radii of galaxies makes the assumption of dark matter superfluous. The continents and our everyday environment are not subject to expansion or scale drift.

Demographic and socio-economic developments couple with other requirements to satisfy human needs result in rapid urban expansion sometimes with increasing rate of surface extent greater than the rate of growth of population, that result in continuous sealing of ground surface thereby affecting ecosystem services. This study applied remote sensing toward achieving the progress of SDGs and stage to determine the ratio of the rate of land consumption to the rate of population growth of Gombe metropolis. QGIS 2.18 was used for the image processing and classification analysis for the key Landsat ETM+ (Enhanced Thematic Mapper), Impervious Surface Indices and population data to inform on the urban trend and LCR/PGR for the periods 2000-2005, 2005-2010, and 2010-2015. The result appears that the LCR/PGR for the periods of study show split trends. During 2000-2005 the result shows that the study area expanded outward with LCR/PGR of 1.2. The result also indicate that during 2005-2010, the study area densified with little expansion with the LCR/PGR of 0.8. The result further reveals that during 2010-2015 the LCR/PGR reached 1.8. Pointing that the study area expanded outward with the rate of ground sealing getting high.

(1) Background: Group A rotaviruses (RVAs) are the primary cause of severe intestinal diseases in piglets. Porcine rotaviruses (PoRVs) are widely prevalent in Chinese farms, resulting in significant economic losses to the livestock industry. However, isolation of PoRVs is challenging, and their pathogenicity in piglets is not well understood. (2) Methods: We conduct clinical testing on a farm in Jiangsu Province, China, and isolate strains of porcine rotavirus by continuously passaging on MA104 cells. Subsequently, the pathogenicity of the isolated strain in piglets was investigated.The piglets of the PoRV-infection group were orally inoculated with 1 mL of 1.0 × 10⁶ TCID50 PoRV, whereas those of the mock-infection group were fed with an equivalent amount of DMEM. (3) Results: Fecal samples were collected from 28 piglets, all of which tested positive for RVAs. A G5P[23] genotype porcine rotavirus strain was successfully isolated from one of the positive samples and named RVA/Pig/China/JS/2023/G5P[23](JS). The genomic constellation of this strain was G5-P[23]-I5-R1-C1-M1-A8-N1-T1-E1-H1. Sequence analysis revealed that the genes VP3, VP7, NSP2, and NSP4 of the JS strain were closely related to human RVAs, whereas the remaining gene segments were closely related to porcine RVAs, indicating a reassortment between porcine and human strains. Furthermore, infection of 15-day-old piglets with the JS strain resulted in a diarrheal rate of 100% (8 of 8) and mortality rate of 37.5% (3 of 8).(4) Conclusion: The isolated G5P [23] genotype rotavirus strain, which exhibited strong pathogenicity in piglets, may have resulted from recombination between porcine and human strains. It may serve as a potential candidate strain for developing vaccines, and its immunogenicity can be tested in future studies.

We present the results of a twofold experimental and computational study of (0001) GaN/AlN multilayers forming pseudomorphic superlattices. High-Resolution Transmission Electron Microscopy (HRTEM) shows that heterostructures with GaN Quantum Wells (QW) four c-lattice parameters thick are misfit-dislocation free. Accurate structural data are extracted from HRTEM images via a new methodology optimizing the residual elastic energy stored in the samples. Total energy calculations are performed with several models analogous to the experimental QWs with increasing thicknesses of GaN, whereas this of the AlN barrier is kept fixed at n=8 c-lattice parameters. With vanishing external stresses, minimum energy configurations of the studied systems correspond to different strain states. Linear elasticity accurately yields the corresponding lattice parameters, suppressing the need for on-purpose total energy calculations. Theoretically justified parabolic fits of the excess interfacial energy yield the values of interfacial stress and elastic stiffness as functions of the GaN QW thickness. Total species-projected densities of states and gap values extracted therefrom allow deciphering the effect of the evolving strain on the electronic structure of the superlattice. It is found that the gap energy decreases linearly with increasing the strain of the QW. These results are briefly discussed in the light shed by previous works from the literature.

Isometric exercises for physiotherapeutic rehabilitation are often prescribed, with little quantification of the load being prescribed. This article aimed to provide a framework and practical examples of how the physiotherapist may take a more quantitative evidence-based approach to isometric assessment, monitoring, and exercise prescription of knee osteoarthritis, by integrating a strain gauge into their practice. Strength measures to monitor were discussed. A series of fourteen studies were reviewed, with the intent of identifying isometric exercises that had been utilized in the rehabilitation of knee osteoarthritis. Of the fourteen studies, the three most identified isometric exercises were seated knee extension, knee flexion, and the supine straight leg raise. The integration of strain gauge technology with these exercises provided the focus of the remainder of the article.

Dielectric elastomers, such as thermoplastic polyurethanes (TPU), are widely used as dielectric layer, emulation layer and substrate of flexible and stretchable devices. To construct capacitors and actuators that work stably upon deformation, it has become an urgent need to investigate the evolution of dielectricity under stress and strain. However, the lack of effective methods for estimating the dielectric constant of elastomers under strain poses a big challenge. This article reports a device for in-situ measuring the dielectric constant of TPU under strain. It is found that upon stretching TPU to a strain of 400%, its dielectric constant decreases from 8.47 to 2.94. In addition, combined Fourier-transform infrared spectroscopy, X-ray scattering technique, and atomic force microscopy have been utilized to characterize the evolution of microstructure under strain. The investigation under tensile strain reveals that a decreased density and average size of polarized hard domains, along with a tendency of the molecular chains to align in parallel with the tensile stress. The evolution of the microstructures results in a reduction of the dielectric constant parallel to the electric field in TPU. Our work provides valuable experimental reference for improving the stability of flexible sensors and actuators based on dielectric elastomers.

Mycobacterium tuberculosis variant bovis (MBO) has one of the widest known mammalian host ranges, including humans. Despite characterization of this pathogen in the 1800s, and whole genome sequencing of a UK strain (AF2122) nearly two decades ago, the basis of its host specificity and pathogenicity remains poorly understood. Recent experimental calf infection studies show that MBO strain Ravenel (MBO Ravenel) is attenuated in the cattle host. In the present study, experimental infections were performed to define attenuation and whole genome sequencing completed to identify regions of differences (RD) and single nucleotide polymorphisms (SNPs) to explain the observed attenuation. Comparative genomic analysis of MBO Ravenel against three pathogenic strains of MBO (strains AF2122-97, 10-7428 and 95-1315) was performed. Experimental infection studies on 5 calves each, with either MBO Ravenel or 95-1315, revealed no visible lesions in all 5 animals in the Ravenel group despite robust IFN-γ responses. Out of 486 polymorphisms in the present analysis, 173 were unique to MBO Ravenel among the strains compared. A high-confidence subset of 9 unique SNPs were missense mutations in genes with annotated functions impacting 2 major MBO survival and virulence pathways: 1) Cell wall synthesis & transport [espH (A103T), mmpL8 (V888I), aftB (H484Y), eccC5 (T507M), rpfB (E263G)], and 2) Lipid metabolism & respiration [mycP1(T125I), pks5 (G455S), fadD29 (N231S), fadE29 (V360G)]. These substitutions likely contribute to the observed attenuation. Results from experimental calf infections and the functional attributions of polymorphic loci on the genome of MBO Ravenel provide new insights into the strain’s genotype-disease phenotype associations.

In this study, a flexible strain sensor is devised using corrugated poly(3-hexylthiophene) (P3HT) thin film. In the previous studies, the P3HT-based photoactive thin film was shown to generate direct current (DC) under broadband light, and the generated DC voltage varied with applied tensile strain. Yet, the mechanical resiliency and strain sensing range of the P3HT-based thin film strain sensor were limited due to relatively more brittle thin film constituent—poly(3,4-ethylenedioxythiophene)-polystyrene(sulfonate) (PEDOT:PSS) conductive thin film as a bottom electrode. To address this issue, it is aimed to design mechanically resilient strain sensor using corrugated thin film constituents. Buckling is induced to form corrugation in the thin films by applying pre-strain to the substrate, where the thin films are deposited, and releasing the pre-strain afterwards. It is known that corrugated thin film constituents exhibit different optical and electronic properties from non-corrugated ones. Therefore, to optimize design of the flexible strain sensor, it was studied to understand how the applied pre-strain and thickness of the PEDOT:PSS thin film affect the optical and electrical properties. Also, pre-strain effect on light absorptivity of the corrugated P3HT-based thin films was studied. In addition, strain effect was investigated on the optical and electrical properties of the corrugated thin film constituents. Finally, flexible strain sensors are fabricated by following the design guideline, which is suggested from the studies on the corrugated thin film constituents, and DC voltage strain sensing capability was validated. As a result, flexible strain sensor exhibited tensile strain sensing range up to 5% at frequency up to 15 Hz with maximum gage factor ~7.

The goal of the current study was to discover a novel potential probiotic strain of Lactobacillus spp. with anti-Escherichia coli activity from locally produced yogurt in Tongi, Gazipur, Bangladesh, compare its antagonistic activity with a commercial probiotic mixture of several strains, and approve a novel method for confirming the viability and relative abundance of the microbial community in a probiotic mixer. We carried out 16S sequencing, 16S metagenomics, Transmission Electron Microscopy (TEM) analysis, and other in vitro laboratory experiments to reach this objective. The strain TY-11 was identified as Lactobacillus delbrueckii subsp. indicus (16S sequence accession number OQ652026). It was gram-positive, anaerobic, lactose fermenting, and round-ended rod that typically measured 0.7 to 1.3 µm by 2.2 to 9 µm. In addition to having seven probiotic characteristics, it also showed an antagonistic impact on six different pathogens, but what's more noteworthy is that E. coli was the pathogen it inhibited most strongly (inhibition zone diameter was 18.88±0.18 mm). The most important and ground-breaking finding of this work was determining the probiotic features of a new probiotic strain, TY-11, whose antibacterial activity was virtually as effective as that of the probiotic combination with three different strains. Furthermore, the results of 16S high throughput sequencing and the conventional plate count method demonstrated a strong correlation (0.999) at the genus level, indicating that the use of both of these approaches in combination may be a practical way to assess the relative abundance of the microbial community and their viability in commercially available probiotic blends.

Inflation and exchange rates have great influence on consumer prices especially on imports and exports. Exchange rate fluctuations create inefficiency and distort world prices whereas changes in inflation rates have a direct impact on consumer goods prices which incidentally include exchange rates. There is a direct interdependence between inflation and exchange rates and this paper is aimed at investigating this relationship in dynamic context. It tries to find out how changes in inflation and exchange rates impact on another by adopting the econometric and copula approaches. Both inflation and exchange rates data are susceptible to volatility clustering, possess fat tails and are skewed coupled with conditional heteroskedasticity. Hence we model the univariate distributions by using ARMA$(p,q)$-GARCH$(x,y)$ so as to capture the most important stylized features of inflation and exchange rates. A bivariate model is then constructed by coupling the marginal distributions of inflation and exchange rates using the survival Clayton copula. Empirical results from monthly inflation and exchange rates data show positive correlation between the two based on Kendall $\tau$ test which confirms that a change in inflation results in change of exchange rates an vice versa hence there is co-movement. Furthermore, by the Granger causality test, exchange rates spikes cause changes in inflation rates. The results of the study have implications on economic policy design and hedging strategies for traders on imports and exports.

Various crystallite size estimation methods were used to analyze X-ray diffractograms of spherical cerium dioxide and donut-like titanium dioxide anatase nanoparticles aiming to evaluate their reliability and limitations. The microstructural parameters were estimated from Scherrer, Monshi, Williamson-Hall, and their variants: i) uniform deformation model, ii) uniform strain deformation model, and iii) uniform deformation energy density model, and also size-strain plot, and Halder-Wagner method. For that, and improved systematic Matlab code was developed to estimate the crystallite sizes and strain, and the linear regression analysis was used to compare all the models based on the coefficient of determination, where the Halder Wagner method gave the highest value (close to 1). Therefore, being the best candidate to fit the X-ray Diffraction data of metal-oxide nanoparticles. Advanced Rietveld was introduced for comparison purposes. Refined microstructural parameters were obtained from a nanostructured 40.5 nm Lanthanum hexaboride nanoparticles and correlated with the above estimation methods and transmission electron microscopy images. In addition, electron density modelling was also studied for final refined nanostructures, and μ-Raman spectra were recorded for each material estimating the mean crystallite size and comparing by means of a phonon confinement model.

Since the first published genome sequence of Trypanosoma cruzi in 2005, there has been tremendous technological advance in genomics, reverse genetics, and assay development for this elusive pathogen. However, there is still an unmet need for new and better drugs to treat Chagas disease. Here we introduce a T. cruzi assay strain that is useful for drug research as well as basic studies in host-pathogen interaction. Trypanosoma cruzi STIB980 is a strain of discrete typing unit TcI that grows well in culture as axenic epimastigotes or intracellular amastigotes. We have evaluated the optimal parameters for genetic transfection and constructed derivatives of T. cruzi STIB980 that express reporter genes for fluorescence- or bioluminescence-based drug efficacy testing, as well as a Cas9-expressing line for CRISPR/Cas9-mediated gene editing. The genome of T. cruzi STIB980 was sequenced by combining short-read Illumina with long-read Oxford Nanopore technologies. The latter served for the primary assembly, the former to correct mistakes and fill the gaps. This resulted in a high-quality nuclear haplotype assembly of 28 Mb in 400 contigs, containing 10,043 open-reading frames with a median length of 1077 bp. We believe that T. cruzi STIB980 is a useful addition to the antichagasic toolbox, and propose that it can serve as a DTU TcI reference strain for drug efficacy testing.

(1)Background: Early-age concrete shrinkage induces stress that impact the cost and service life of concrete pavements. (2)Methods: In this study, strain measurements of field slabs were conducted and a methodology was presented that independently derived autogenous, drying, and thermal shrinkages in the initial stages of concrete placement. Total strain was measured according to five different environmental conditions and shrinkage strain was calculated for each condition. (3)Results: By measuring the strain of the slab and the specimen, the drying shrinkage strain was measured to be approximately 54% better than that by the conventional non-stressed cylinder method because it was possible to measure the drying shrinkage strain at the surface rather than in the middle part of the slab along its depth direction. When the water-to-cement ratio increased (35→40%), there was a considerable reduction (317με→82με) of autogenous shrinkage strain for the concrete at 28 days of age. Furthermore, calculation of stress-dependent strain allowed the presentation of more intuitive and accurate results. (4)Conclusion: As the measurement of independent shrinkage occurrence is possible, the consequent calculated result of the stress-dependent strain acting on real slabs will facilitate improvement in the construction quality, reduction in the development of defects in the concrete structure, and increase in the service life.

Language is an essential aspect of teaching and learning mathematics. It is necessary for communicating, transmission of concepts and ideas, and formation of meaning of mathematical concepts. In mathematics, besides symbols, which are usually common in different languages, words and expressions are used, which may invoke different concept images to students in various languages. Some words are used in mathematics and in everyday language with different meanings, while others are used only in mathematics or in mathematics and other disciplines in similar but non-identical ways. In Mathematical Analysis, the used vocabulary is gradually enhanced, and the concepts are defined in a more formal way. In the current study, the language used regarding mathematics of change is examined, focusing on rate of change and in relation to misconceptions of students.

This work presents a linear smoothing scheme over high-order triangular elements in the framework of a cell-based strain smoothed finite element method for two-dimensional nonlinear problems. The main idea behind the proposed linear smoothing scheme for strain-smoothed finite element method (S-FEM) is no subdivision of finite element cells to sub-cells while the classical S-FEM needs sub-cells. Since the linear smoothing function is employed, S-FEM is able to use quadratic triangular or quadrilateral elements. The modified smoothed matrix obtained node-wise is evaluated. In the same manner with the computation of the strain-displacement matrix, the smoothed stiffness matrix and deformation graident are obtained over smoothing domains. A series of benchmark tests are investigated to demonstrate validity and stability of the proposed scheme. The validity and accuracy are confirmed by comparing the obtained numerical results with the standard FEM using 2nd-order triangular element and the exact solutions.

We show how the excitonic features of biaxial MoS₂ flakes are very sensitive to biaxial strain. We find a lower bound for the gauge factors of the A exciton and B exciton of (-41 ± 2) meV/% and (-45 ± 2) meV/% respectively, which are larger than those found for single-layer MoS₂. Interestingly, the interlayer exciton feature also shifts upon biaxial strain but with a gauge factor that is systematically larger than that found for the A exciton, (-48 ± 4) meV/%. We attribute this larger gauge factor for the interlayer exciton to the strain tunable van der Waals interaction due to the Poisson effect (the interlayer distance changes upon biaxial strain).

We explored the dynamics of the two interacting information systems. We show that for the Markovian marginal systems the driving force for information dynamics is determined by both the information landscape and information flux. While the information landscape can be used to construct the driving force to describe the equilibrium time reversible information system dynamics, the information flux can be used to describe the nonequilibrium time-irreversible behaviours of the information system dynamics. The information flux explicitly breaks the detailed balance and is a direct measure of the degree of the nonequilibriumness or time irreversibility. We further demonstrate that the mutual information rate between the two subsystems can be decomposed into the equilibrium time-reversible and nonequilibrium time-irreversible parts respectively. This decomposition of the mutual information rate (MIR) corresponds to the information landscape-flux decomposition explicitly when the two subsystems behave as Markov chains. Finally, we uncover the intimate relationship between the nonequilibrium thermodynamics in terms of the entropy production rates and the time-irreversible part of the mutual information rate. We found that this relationship and MIR decomposition still hold for the more general stationary and ergodic cases. We demonstrate the above features with two examples of the bivariate Markov chains.

A new utilization of entropy in the context of buckling is presented. The novel concept connecting strain energy and entropy for a pin-ended strut is derived. This concept rationalizes the ranking of buckling modes based on strain energy under the assumption of given entropy. By assigning identical entropy to all buckling modes, they can be ranked according to their deformation energy. Conversely, with identical strain energy assigned to all modes, ranking according to entropy is possible. Decreasing entropy was found to represent the scaling factors of buckling modes that coincide with the measurement of initial out-of-straightness imperfections in IPE160 beams. Applied to steel plane frames, scaled buckling modes can be used to model initial imperfections. It is demonstrated that the entropy (scale factor) for given energy roughly decreases with the inverse square of the mode index. For practical engineering, the study presents the possibility of using scaled buckling modes of steel plane frames to model initial geometric imperfections. Entropy proves to be a valuable complement to strain energy in structural mechanics.

Staphylococcus aureus is a high-priority pathogen causing severe infections with high morbidity and mortality worldwide. Many S. aureus strains are methicillin-resistant (MRSA) or even multi-drug resistant. It is one of the most successful and prominent modern pathogens. An effective fight against S. aureus infections requires novel targets for antimicrobial and antistaphylococcal therapies. Recent advances in whole-genome sequencing and high-throughput techniques facilitate the generation of genome-scale metabolic models (GEMs). Among the multiple applications of GEMs is drug-targeting in pathogens. Hence, comprehensive and predictive metabolic reconstructions of S. aureus could facilitate the identification of novel targets for antimicrobial therapies. This review aims at giving an overview of all available GEMs of multiple S. aureus strains. We downloaded all 114 available GEMs of S. aureus for further analysis. The scope of each model was evaluated, including the number of reactions, metabolites, and genes.Furthermore, all models were quality-controlled using Mᴇᴍᴏᴛᴇ, an open-source application with standardized metabolic tests. Growth capabilities and model similarities were examined. This review should lead as a guide for choosing the appropriate GEM for a given research question. With the information about the availability, the format, and the strengths and potentials of each model, one can either choose an existing model or combine several models to create models with even higher predictive values. This facilitates model-driven discoveries of novel antimicrobial targets to fight multi-drug resistant S. aureus strains.

In California, an average of 41,900 patients are diagnosed annually with Staphylococcus bacterial infection; out of these, 24,090 patients have methicillin-resistant Staphylococcus aureus (MRSA) infection and 17,810 patients have methicillin-sensitive Staphylococcus aureus (MSSA) infection. The aim of this paper is to find out whether there is a significant difference in strain dominancy and in what direction. The paper gathered and analyzed data for period of five years of infection rate due to Staphylococcus aureus. This study indicates that a significant difference in dominancy exists, the MRSA infection rate (an average of five years period) is 1.35 times higher than the MSSA infection rate (P-value < 0.05, CI: 95%), but the gap between the two infection rates is decreasing. The infection rate of both MRSA and MSSA is in a path of decline.

Environmental effects and climate change are lately representing an increasing strain of the coastal areas which topography strongly depends on these conditions. However, the processes by which weather and environmental phenomena influence the highly variable beach morphology are still unknown. A continuous monitoring of the beach environment is necessary to implement protection strategies. This paper presents the results of an innovative study performed on a coastal area using satellite remote sensing data with the aim of understanding how environmental phenomena affect beaches. Two-years of synthetic aperture radar (SAR) Sentinel-1 images are used over a test area in Noordwijk, the Netherlands. At the same time as the SAR acquisitions, information on tidal and weather conditions are collected and integrated from nearby meteorological stations. Dedicated codes are implemented in order to understand the relationship between the SAR amplitude and the considered phenomena: wind, precipitation, tidal conditions. Surface roughness is taken into account. The results indicate a strong correlation between the amplitude and the wind. No particular correlation or trend could be noticed in the relation with the precipitation. The analysis of the amplitude also shows a decreasing trend moving from the dry area of the beach towards the sea and the correlation coefficient between the amplitude and the tide level gets negative with the increase of the water content.

Grating (moiré) interferometry is one of the well-known methods for full-field in-plane displacement and strain measurement. There are many design solutions for grating interferometers, including systems with a microinterferometric waveguide head. This article proposes a modification to the conventional waveguide interferometer head, enabling the implementation of a polarization fringe phase shift for automatic fringe pattern analysis. The article presents both the theoretical consideration of the proposed solution and its experimental verification, along with the concept of the in-plane displacement/strain sensor using the described head.

The investigation on the issue of damage diagnosis based on strain modal parameters is conducted in this paper using simply supported wooden Beams as the study's object. First, ABAQUS is utilized to create finite element models of intact wooden beams as well as wooden beams with varying degrees of damage and perform modal analyses on them. Next, damage identification studies are conducted on the wooden beam structure using various strain modal parameters (strain mode strain modal difference, strain modal curvature difference), the timber beam damage identification test then yields the modal parameters of timber beams under various damage situations, and the test findings are contrasted with those of the numerical simulation. The outcomes demonstrate that the damage identification of the test data using the three types of damage identification indexes is consistent with the results of the numerical simulation; the three types of damage identification indexes can locate the damage to timber beams, but the identification effect of the indexes is different, the best-recognized metric is the strain mode curvature difference; the next best is the strain mode difference, and the worst is the strain modes. The study's findings can serve as a guide for future damage detection on wood beams.

Inflation is a crucial macroeconomic indicator which measures changes in the general level of prices of goods and services. In recent years, a series of successive events affected the inflation rates. To fight this increase in inflation, governments start to take different actions through their monetary and fiscal policies. In this research 10 independent parameters were used to see their effect on inflation rates. Some are traditional like GDP, Population, and exchange rate while others are some new technology related parameters like E-money payments transactions and number of Institutions offering payment services/instruments. The dependent parameter is the consumer price index (CPI). All parameters were taken in 8 years period (2013-2020). Supervised machine learning is used to run a robust regression model. The results show that technology advancement in payments is not a catalyst for price inflation if it is used properly and under regulations and control monetary policies. The results direct regulators to have a good understanding of the situation and take the right action in their policies of adopting fintech businesses.

The seasonally adjusted civilian labor force participation rate, the sum of employed and unemployed persons as a percentage of the civilian non-institutional population, is analysed in the general to specific modelling framework with a saturating set of step indicators from January 1977 through June 2018. The results indicate that, ceteris paribus, the rise in the ratio of women to men in the labor force in addition to positive demographic movements can largely account for the rise in the labor force participation rate up to January 2000. Subsequently, the aging population helps to explain the decline. Recessions play a transitory role.

We propose an electrocardiogram (ECG) signal-based algorithm to estimate the respiratory rate is a significant informative indicator of physiological state of a patient. The consecutive ECG signals reflect the information about the respiration because inhalation and exhalation make transthoracic impedance vary. The proposed algorithm extracts the respiration-related signal by finding out the commonality between the frequency and amplitude features in the ECG pulse train. The respiration rate can be calculated from the principle components after the procedure of the singular spectrum analysis. We achieved 1.7569 breaths per min of root-mean-squared error and 1.7517 of standard deviation with a 32-seconds signal window of the Capnobase dataset, which gives notable improvement compared with the conventional Autoregressive model based estimation methods.

Globally, the use of whole-cell matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS) in clinical microbiology laboratories has increased considerably. With the rapid growth of artificial intelligence technology, there is an increasing number of areas devoted to solving problems by implementing machine learning-based methods. Applying the use of artificial intelligence to the analysis of the massive amount of information obtained in the mass spectrum derived from MALDI-TOF MS should be a breakthrough in clinical microbiology. Specifically, it would facilitate a more rapid and accurate strain typing or antibiotic susceptibility test (AST) based on whole-cell MALDI-TOF MS spectra, and hence, it is a promising solution. Even though the reproducibility of peaks could result in some critical problems, computational methods have been developed to address this issue. Therefore, clinical microbiologists are able to perform strain typing or an AST as smoothly and easily as identifying species by using MALDI-TOF MS and artificial intelligence.

A highly sensitive strain sensor based on tunable cascaded Fabry-Perot interferometers (FPIs) is proposed and experimentally demonstrated. Cascaded FPIs consist of a sensing FPI and a reference FPI which effectively generate the Vernier Effect (VE). The sensing FPI comprises a hollow core fiber (HCF) segment sandwiched between single-mode fibers (SMFs), and the reference FPI consists of a tunable air reflector, which is constituted by a computer programable fiber holding block to adjust the desired cavity length. Simulation results predict the dispersion characteristics of modes carried by HCF. The sensor’s parameters are designed corresponding to a narrow bandwidth range, i.e., 1530 nm to 1610 nm. Experimental results demonstrate that the proposed sensor exhibits optimum strain sensitivity of 23.9 pm/με in the range of 0 to 3000 με which is 13.73 times higher than the single sensing FPI strain sensitivity of 1.74 pm/με. The strain sensitivity of the sensor can be further enhanced by extending the source bandwidth. The proposed sensor exhibits ultra-low temperature sensitivity of 0.49 pm/°C in the wider temperature range of 25 °C to 135 °C, providing good isolation for eliminating cross-talk between strain and temperature. The sensor is very robust, cost-effective, easy to manufacture, repeatable, and shows a highly linear and stable response in the wider range of axial strain. Based on the sensor’s performance, it may suit plenty of practical applications in the real sensing world

Myxobacteria feature unique biological characteristics including their capability to glide on surface, undergo different multicellular developmental stages and produce structurally unique natural products such as the catecholate-type siderophores myxochelin A and B. Herein, we report the isolation, structure elucidation and biosynthesis of the new congener myxochelin B-succinate from the terrestrial myxobacterial strain MSr12020, featuring a succinyl decoration at its primary amine group. Myxochelin-B-succinate exhibited antifungal growth inhibition and moderate cytotoxic activity against selected human cancer cell lines. This unique chemical modification of myxochelin B might provide interesting insights for future microbiological studies to understand the biological function and biosynthesis of secondary metabolite succinylation.

The stress imposed by ethanol to Saccharomyces cerevisiae cells are one of the most challenging limiting factors in industrial fuel-ethanol production. Consequently, the toxicity and tolerance to high ethanol concentrations has been the subject of extensive research, allowing the identification of several genes important for increasing the tolerance to this stress factor. However, most studies were performed with well characterized laboratory strains, and how the results obtained with these strains work in industrial strains remains unknown. In the present work we have tested three different strategies known to increase ethanol tolerance by laboratory strains in an industrial fuel-ethanol producing strain: overexpression of the TRP1 or MSN2 genes, or overexpression of a truncated version of the MSN2 gene. Our results show that the industrial CAT-1 strain tolerates up to 14% ethanol, and indeed the three strategies increased its tolerance to ethanol. When these strains were subjected to fermentations with high sugar content and cell-recycle, simulating the industrial conditions used in Brazilian distilleries, only the strain with overexpression of the truncated MSN2 gene showed improved fermentation performance, allowing the production of 16% ethanol from 33% of total reducing sugars present in sugarcane molasses. Our results highlight the importance of testing genetic modifications in industrial yeast strains under industrial conditions in order to improve the production of industrial fuel ethanol by S. cerevisiae.

We provide an extensive and systematic investigation of exciton dynamics in droplet epitaxial quantum dots comparing the cases of (311)A, (001) and (111)A surfaces. In spite of a similar s-shell exciton structure common to the three cases, the absence of a wetting layer for (311)A and (111)A samples leads to a larger carrier confinement with respect to (001), where a wetting layer is present. Moreover, this leads to a more pronounced dependence of the binding energies of s-shell excitons on the quantum dot size and to a strong anti-binding character of the positive charged exciton for smaller quantum dots. In-plane geometrical anisotropies of (311)A and (001) quantum dots lead to a large electron-hole fine interaction (fine structure splitting, FSS ~ 100 ueV) whereas for the three-fold symmetric (111)A counterpart this figure of merit is reduced of about one order of magnitude. In all these cases we do not observe any size dependence of the fine interactions. Heavy-hole/light-hole mixing is present in all the studied cases leading to a broad spread of linear polarization anisotropy (from 0 up to about 50%) irrespective of surface orientation (symmetry of the confinement), fine interactions and nanostructure size. These results are important for the further development of ideal single and entangled photon sources based on semiconductor quantum dots.

Bioethanol has been considered as an excellent alternative to fossil fuels since it importantly contributes to the reduced consumption of the crude oil and to the alleviation of environmental pollution [1]. Up to now, the baker yeast Saccharomyces cerevisiae is the most common eukaryotic microorganism used in ethanol production. The inability of S. cerevisiae to grow on pentoses, however, hinders its effective growth on plant biomass hydrolysates, which contain large amounts of C5 and C12 sugars. The industrial-scale bioprocessing requires high temperature bioreactors, diverse carbon sources, and the high titer production of volatile compounds [2]. These criteria indicate that the search for alternative microbes possessing useful traits that meet the required standards of bioethanol production is necessary. Compared to other yeasts, Kluyveromyces marxianus has several advantages over the others, e.g. it could grow on a broad spectrum of substrates (C5, C6 and C12 sugars) [3], tolerate to high temperature, toxin [4,5] and a wide range of pH values [6], and produce volatile short-chain ester [2]. K. marxianus also shows a high ethanol production rate at high temperature and is a Crabtree-negative species [7]. These attributes make K. marxianus a promise as an industrial host for the biosynthesis of biofuels and other valuable chemicals.

The Finite size Lyapunov exponent (FSLE) has been used extensively since the late 1990’s to diagnose turbulent regimes from Lagrangian experiments and to detect Lagrangian coherent structures in geophysical flows and two-dimensional turbulence. Historically, the FSLE was defined in terms of its computational method rather than via a mathematical formulation, and the behavior of the FSLE in the turbulent inertial ranges is based primarily on scaling arguments. Here we propose an exact definition of the FSLE based on conditional averaging of the finite amplitude growth rate (FAGR) of the particle pair separation. With this new definition, we show that the FSLE is a close proxy for the inverse structural time, a concept introduced a decade before the FSLE. The (in)dependence of the FSLE on initial conditions is also discussed, as well as the links between the FAGR and other relevant Lagrangian metrics, such as the finite time Lyapunov exponent and the second order velocity structure function.

Thalassemia is one of the most prevalent genetic disorders worldwide which has been previously found to have an association with several physiological and organ complications. Several studies found both its positive and inverse correlation with glomerular filtration rate (GFR). Therefore, in this meta-analysis, we tried to assess the accurate correlation of thalassemia with GFR. We searched in Google Scholar, PubMed, and ScienceDirect, and from the initial 96 articles we finally could include 15 studies. The quality and publication bias assessment confirmed that all the studies were of high to moderate quality with no publication bias. The main outcome of the mean difference (MD) was -6.45, 95%CI: -18.50, 5.60 (P<0.00001), which indicated a negative correlation of GFR with thalassemia. The sensitivity analyses found one study as a slight outlier and reanalyzing the data excluding that study MD was achieved as -13.90, 95%CI: -24.22, -3.59 (P<0.00001) which even strongly supports our main outcome. Our result determined that the GFR is generally higher in healthy people as compared to thalassemia patients.

Influenza A viruses (IAVs) evolve via point mutations and reassortment of viral gene segments. The patterns of reassortment in different host species differ considerably. We investigated the genetic diversity of IAVs in wild ducks and compared it with the viral diversity in gulls. The complete genomes of 38 IAVs of H1N1, H1N2, H3N1, H3N2, H3N6, H3N8, H4N6, H5N3, H6N2, H11N6 and H11N9 subtypes isolated from wild mallard duck and gull habitants of a pond in Moscow city, Russia were sequenced. The sequences were closely related to those of avian IAVs isolated in Sweden and the Netherlands. The analysis of phylogenetic trees showed that stable viral genotypes do not persist from year to year in ducks owing to frequent gene reassortment. For comparison, similar analyses were carried out using sequences of IAVs isolated in the same period from ducks and gulls in the Netherlands. Our results revealed a significant difference in diversity and rates of reassorment of IAVs in ducks and gulls.

Covid-19 fatality rates of 0.37% (Gangelt, Germany) and 0.17% (Santa Clara, USA) have been reported, estimated from serological studies. We show that the two confidence intervals strongly overlap when the uncertainty in the number of deaths is taken into account, so that the two investigations may be regarded as representative of the same population (tentatively: “Western society with no overload of the Health Care System during the pandemic”). Combining the results, the Covid-19 fatality rate is estimated to be found with 95% confidence in the range [0.1%; 0.3%].

Conventional economic theory outlines that developing countries experience economic growth through an undervalued exchange rate and that exchange rate overvaluations has negative long term effects on economic growth. This paper examined the impact of exchange rate movements as well as exchange rate misalignments on economic growth for the Trinidad and Tobago economy over the period 1960 to 2016. We find statistically significant evidence that both exchange rate appreciation and misalignments impact negatively on economic growth in the T&T economy. Drilling deeper we find interestingly that there exist no non-linear effects of exchange rate misalignments on growth. Specifically we find statistically significant evidence that both overvaluations and undervaluations hamper economic growth in the Trinidad and Tobago economy. We attribute this to T&T’s small and underdeveloped manufacturing sector that tends to be overlooked on account of its energy resources, in addition to the fact that its manufacturing sector is highly import oriented. A major policy recommendation would be for the critical reassessment of the rules governing the HSF, as government expenditure was allowed to follow energy revenues due to its current limitations.

Fipronil is an insecticide widely used in the agricultural and veterinary sectors for its efficacy in pest control. The presence of fipronil in the environment is mainly due to agricultural and domestic practices and is frequently found in different types of environmental matrices in concentrations ranging from µg/L to mg/L and can be hazardous to non-target organisms due to its high toxicity. This study was carried out to obtain and characterize microorganisms from soil which are capable of biodegrading fipronil that could be of great biotechnological interest. For this purpose, a bioprospecting was carried out using fipronil (0.6 g/L) as the main source of carbon and nitrogen for growth. Once obtained, the strain was identified by sequencing the 16S ribosomal RNA (rRNA) gene and the capacity to degrade fipronil was monitored by GC-MS. Our study showed the presence in soil samples of the strain identified as Enterobacter chengduensis, which was able to metabolize fipronil and its metabolites during the mineralization process. Enterobacter chengduensis was able to biodegrade fipronil (96%) and its metabolites fipronil-sulfone (92%) and fipronil-sulfide (79%) in 14 days. Overall, the results of this study provided a bacterium with great potential that could contribute to the degradation of fipronil in the environment.

The standard edge crush test (ECT) allows to determine the crushing strength of the corrugated cardboard. Unfortunately, this test cannot be used to estimate the compressive stiffness, which is an equally important parameter. It is because, any attempt to determine this parameter using current lab equipment quickly ends in a fiasco. The biggest obstacle is obtaining a reliable measurement of displacements and strains in the corrugated cardboard sample. In this paper, we present a method that not only allows to reliably identify the stiffness in the loaded direction of orthotropy in the corrugated board sample, but also the full orthotropic material stiffness matrix. The proposed method uses two samples: (a) traditional, cut crosswise to the wave direction of the corrugated core, and (b) cut at an angle of 45 degrees. Additionally, in both cases, an optical system with digital image correlation (DIC) is used to measure the displacements and strains on the outer surface of samples. The use of a non-contact measuring system allows to avoid using the measurement of displacements from the crosshead, which is burdened with a large error. Apart from the new experimental configuration, the article also proposes a simple algorithm to quickly characterize all sought stiffness parameters. The obtained results are finally compared with the results obtained in the homogenization procedure of the cross-section of the corrugated board. The results were consistent in both cases.

Fabry-Perot air chamber was constructed at the melting point (splicing location) of two single-mode fibers by glycerin assisted self-expansion method. The morphology of the Fabry-Perot air chamber was fabricated and optimized by modulating the splicing parameters (drawing process, discharging location, time and intensity) and the fibers’ end-face (plane or arc). The in-line or reflected Fabry-Perot cavities have been applied to determine the tensile strain in the range of 0-1.2 N. The train sensing performance of the spherical shaped FP cavity has been experimentally demonstrated with the best sensitivity of 3.628 nm/N, corresponding to the resolution of ~0.005 N. The proposed FP fiber sensor has the advantages of low cost, fast fabrication and easy-integration with the common fiber system.

The effects of an external strain tensor on the electrical resistivity of a manganite granular system are investigated using a simple approach describing the induced deformation in terms of the tilt angle between adjacent grains. The results obtained assuming the resistivity of each grain as given by a metallic part, coming from the inner grain, and a surface related tunnel contribution, allow to estimate appreciable resistivity variations even in the case of small deformation angles.

Abstract The COVID-19 pandemic is thought to began in Wuhan, China in December 2019. Mobility analysis identified East-Asia and Oceania countries to be highly-exposed to COVID-19 spread, consistent with the earliest spread occurring in these regions. However, here we show that while a strong positive correlation between case-numbers and exposure level could be seen early-on as expected, at later times the infection-level is found to be negatively correlated with exposure-level. Moreover, the infection level is positively correlated with the population size, which is puzzling since it has not reached the level necessary for population-size to affect infection-level through herd immunity. These issues are resolved if a low-virulence Corona-strain (LVS) began spreading earlier in China outside of Wuhan, and later globally, providing immunity from the later appearing high-virulence strain (HVS). Following its spread into Wuhan, cumulative mutations gave rise to the emergence of an HVS, known as SARS-CoV-2, starting the COVID-19 pandemic. We model the co-infection by an LVS and an HVS, and show that it can explain the evolution of the COVID-19 pandemic and the non-trivial dependence on the exposure level to China and the population-size in each country. We find that the LVS began its spread a few months before the onset of the HVS, and that its spread doubling-time is $\sim 1.59\pm 0.17$ times slower than the HVS. Although more slowly spreading, its earlier onset allowed the LVS to spread globally before the emergence of the HVS. In particular, in countries exposed earlier to the LVS and/or having smaller population-size, the LVS could achieve herd-immunity earlier, and quench the later-spread HVS at earlier stages. We find our two-parameter (the spread-rate and the initial onset time of the LVS) can accurately explain the current infection levels (R^2$\mathrm{=0.74}$; correlation p-value (p) of 5x10^-13$$). Furthermore, countries exposed early should have already achieved herd-immunity. We predict that in those countries cumulative infection levels could rise by no more than 2-3 times the current level through local-outbreaks, even in the absence of any containment measures. We suggest several tests and predictions to further verify the double-strain co-infection model and discuss the implications of identifying the LVS.

Molecular dynamics simulations were carried out to investigate the atomic structure of a model Cu64Zr36 bulk metallic glass (BMG). It is found that the amount of icosahedral content of the system is significantly increased in a well relaxed structure. While we considered four connection types of vertex-, edge-, face-, and volume-sharing, the huge cluster in the relaxed samples mainly involve volume-type connection and exhibits a remarkable athermal plasticity that great stiffness and great yield strength compared to the as-quenched samples. In addition, the bond-angle distribution of annealed sample shows sharp peaks at specific bond angles which is an evidence of crystallized Laves-phase formed by icosahedral atoms, however the peaks are to be broaden after loading, which indicates decreasing amount of icosahedral content and their shape distortion. These results suggest that icosahedral content in a bulk metallic glasses plays a key role to determine the mechanical properties such as rigidity and maximum stress carrying capacity.

The low-temperature environment significantly inhibits the growth and metabolism of denitrifying bacteria, leading to an excessive concentration of ammonia nitrogen and total nitrogen in sewage treatment plants during the cold season. In this study, an efficient denitrifying strain of heterotrophic nitrification–aerobic denitrification(HN-AD) bacteria named HS2 was isolated and screened from industrial sewage of a chemical factory in Inner Mongolia at 8°C. The strain was confirmed to be Achromobacter spiritinus, a colorless rod-shaped bacterium. When cultured with sodium succinate as the carbon source, a carbon-to-nitrogen ratio of 20-30, a shaking rate of 150-180 r/min, and the initial pH of 6-10, the Strain HS2 exhibited excellent nitrogen removal at 8°C. Through the results of whole-genome sequencing, gene amplification, and gas product detection, the Strain HS2 was determined to possess key enzyme genes in both nitrification and denitrification pathways, suggesting a HN-AD pathway of NH4+-N→NH2OH→NO2--N→NO→N2O→N2. At 8°C, the Strain HS2 could completely remove ammonia nitrogen from industrial sewage with an initial concentration of 127.23 mg/L. Microbial species diversity analysis of the final sewage confirmed Achromobacter sp. as the dominant genus, this indicated that the low-temperature denitrifying strain HS2 plays an important role in nitrogen removal of actual low-temperature sewage.

Despite all their advantages, load-bearing concrete shell structures with double curvatures are not frequently in use. The main reason is the complexity of their construction. In such a context, this article starts with a brief, critical review of existing technologies while their pros and cons are highlighted. Against that background the authors then propose a new approach for the highly automated fabrication of gridshell structures from variable modules. To demonstrate the feasibility of such a new technology, a demonstrator called ConDIT 1.0, a sphere-like shell structure composed of several frames was designed and built. The frame modules were fabricated automatically using extrusion-based 3D printing and a printable, strain-hardening cement-based composite (SHCC). This article presents the design of ConDIT 1.0, the mechanical material characterization of printed SHCC, the technology of module production, the results of geometry verification for print modules using 3D scanning, and the procedure for the demonstrator’s assembly.

Nisin, an antibacterial compound produced by Lactococcus lactis strains, has been approved by the US Food and Drug Administration to be used as a safe food additive to control the growth of undesirable pathogenic bacteria. Nisin is commonly described as a pH-dependent primary metabolite, since its production depends on growth and culture pH evolution. However, the relationship between bacteriocin synthesis and the consumption of the limiting nutrient has not been described until now. Therefore, this study aimed to develop a competitive four-dimensional Lotka Volterra-like equation to describe the relationships between culture pH, limiting nutrient (total nitrogen: TN) consumption and production of biomass (X) and nisin (BT) in four series of batch fermentation with L. lactis CECT 539 in diluted whey (DW)-based media. The developed four-dimensional LV-like equation (with a unique set of parameters) could not be used to describe all cultures belonging to each fermentation series. However, the four-dimensional LV-like equation described accurately each individual culture, providing a good description of the relationships between pH, TN, X and BT, higher values for R2 and F-ratios, lower values (&lt; 10%) for the mean relative percentage deviation modulus, with bias and accuracy factor values approximately equal to one.

Initial choice of Learning Rate is a key part of gradient based methods and has a great effect on the performance of the Deep Learning Model.This paper studies the behavior of multiple gradient based optimization algorithm which are commonly used in Deep Learning and compare their performance on various learning rate. As observed popular choice of optimization algorithms are highly sensitive to various choice of learning rates. Our goal is to find which optimizer has an edge over others for a specific setting. We look at two datasets namely MNIST and CIFAR10 for benchmarking. The results are quite surprising, and it will help us to choose a learning rate more efficiently.

Background: Corona virus disease was first reported in Wuhan City, Hubei province, China. Soon the corona virus disease has spread to many countries. World health organization has described the situation as Pandemic. By 12 March 2020, corona virus disease has affected 125 countries around the world. Corona virus was first confirmed in Iran on 19 February 2020. Objective: The aim of writing this small article is to determine the mortality rate of corona virus disease in different cities of Iran. This article will give readers an idea of different ways to control spread of corona virus disease in Iran. Methods: Author has collected the data of daily confirmed cases from different diagnostic centers and hospitals across the country from 19 February 2020 to 1 April 2020. Results: Mortality rate of corona virus disease is roughly 4%. Conclusions: Mortality rate could rise if COVID 19 infection is not controlled.

Regulators require financial institutions to estimate counterparty default risks from liquid CDS quotes for the valuation and risk management of OTC derivatives. However, the vast majority of counterparties do not have liquid CDS quotes and need proxy CDS rates. Existing methods cannot account for counterparty-specific default risks; we propose to construct proxy CDS rates by associating to illiquid counterparty liquid CDS Proxy based on Machine Learning Techniques. After testing 156 classifiers from 8 most popular classifier families, we found that some classifiers achieve highly satisfactory accuracy rates. Furthermore, we have rank-ordered the performances and investigated performance variations amongst and within the 8 classifier families. This paper is, to the best of our knowledge, the first systematic study of CDS Proxy construction by Machine Learning techniques, and the first systematic classifier comparison study based entirely on financial market data. Its findings both confirm and contrast existing classifier performance literature. Given the typically highly correlated nature of financial data, we investigated the impact of correlation on classifier performance. The techniques used in this paper should be of interest for financial institutions seeking a CDS Proxy method, and can serve for proxy construction for other financial variables. Some directions for future research are indicated.

To determine the fracture rate of ceramic crowns and causes of ceramic crown failure, this study used keywords—namely “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown”—to search for articles published in English from 2005 to 2023 in the PubMed electronic database. Rather than using the Boolean logic algorithm between MESH terms and keywords, we accurately calculated the numbers of final clinically tracked cases with crown fractures from the contents of articles. The titles and abstracts of many related articles focused on implant or abutment fracture, while crown fracture was investigated and mentioned only in the main texts of the articles. Our studies included those crowns as well as having more complete data collection. Our search yielded 228, 93, 404, and 358 articles for the keywords “endocrown,” “veneered fixed dental prosthesis,” “monolithic lithium disilicate (LS2),” and “all-ceramic single crown,” respectively. We used the Newcastle–Ottawa Scale (NOS) to assess article quality, and our inclusion criteria were randomized controlled trials (RCT) and cohort study articles involving more than 3 years of follow-up and more than 20 cases. After reviewing, 16 high-quality articles were selected for analysis. The 4.4% crown fracture rate recommended on the basis of most clinical results was achieved in only 6 of the 16 articles. In these 6 articles, the researchers concluded the following reasons that may cause the crown fractures: the thickness of the veneer ceramic material; the connector dimensions; pontic span of the fixed prosthesis; the type of cement; the treatment of the ceramic surface before luting. Other articles inferred that the computer-aided design libraries that were insufficient for the creation of appropriate anatomically supported frameworks for prostheses with ceramic veneers; the thermal expansion coefficient and fracture toughness of the framework material did not match those of the veneer ceramic, resulting in an insufficient area supporting the ceramic veneer then leads to premature crown failure after a long period chewing. The future prospective for material developing could focus on solving those problems and have better clinical results.

Maximal heart rate (HRmax) is a widely used measure of cardiorespiratory fitness. Prediction of HRmax is an alternative to cardiopulmonary exercise testing (CPET), but its accuracy among endurance athletes (EA) requires evaluation. This study aimed to externally validate HRmax prediction models in the EA independently for running and cycling CPET. 4043 runners (age=33.58 (8.12) years; 83.53% males; BMI=23.66 (2.54) kg·m−2) and 1026 cyclists (age=36.88 (9.03) years; 89.67% males; BMI=24.04 (2.65) kg·m−2) underwent maximum CPET. Student t-test, mean absolute percentage error (MAPE), mean absolute error (MAE), and root mean square error (RMSE) were applied to externally validate 8 running and 5 cycling HRmax equations. HRmax was 184.60 (9.79) beats·min−1 and 182.66 (10.28) beats·min−1 respectively for running and cycling, p=0.001. Measured and predicted HRmax differed significantly (p=0.001) for 9 of 13 (69.23%) models. HRmax was overestimated by 8 (61.54%) and underestimated by 5 (38.46%) formulae. Overestimated HRmax ranged 0.08-4.94 beats·min−1 and underestimated HRmax ranged 0.03-4.90 beats·min−1. MAE and RMSE were 0.18-4.94 beats·min−1 and 9.13-10.47, respectively. MAPE ranged 3.95-4.69%. Prediction models do not allow for accurate estimation of HRmax. HRmax was more often underestimated than overestimated. Predicted HRmax can be implemented for EA as a supplemental method but CPET is the preferable approach.

This paper presents the validation of the End Point Rate (EPR) tool for QGIS (EPR4Q), a tool built-in QGIS Graphical Modeler to calculate the shoreline change by End Point Rate method. The EPR4Q tries to fill the gap of user-friendly and free open-source tool for shoreline analysis in Geographic Information System environment, since the most used software - Digital Shoreline Analysis System (DSAS) - although is a free extension, is suited for commercial software. Besides, the best free open-source option to calculate EPR called Analyzing Moving Boundaries Using R (AMBUR), since it is a robust and powerful tool, the complexity and heavy processes can restrict the accessibility and simple usage. The validation methodology consists of applying the EPR4Q, DSAS, and AMBUR on different examples of shorelines found in nature, extracted from the U.S. Geological Survey Open-File. The obtained results of each tool were compared with Pearson correlation coefficient. The validation results indicate that the EPR4Q tool created acquired high correlation values with DSAS and AMBUR, reaching a coefficient of 0.98 to 1.00 on linear, extensive, and non-extensive shorelines, guarantying that the EPR4Q tool is ready to be freely used by the academic, scientific, engineering, and coastal managers communities worldwide.

The last 20 years have seen a surge in scientific activity and promising results in the study of aging and longevity. Many researchers have focused on telomeres, which are composed of a series of TTAGGG repeat nucleotide sequences at the ends of each chromosome. Measurements of the length of these telomere strands show that they decrease in length with increasing age, leading many authors to propose that when the length of these telomere strands decreases sufficiently, the cells enter into a state of replicative senescence, eventually leading to disease and death. These ideas are supported by evidence that short telomere length is correlated with increased mortality. In this paper, we extend this idea to make an actual calculation of the predicted mortality rate caused by short telomere length induced senescence (STLIS). We derive a simple equation for the mathematical relationship between telomere length and mortality rate. Using only 3 parameters based on telomere length measurement data of Canadians, we have calculated both the magnitude and the age dependence of the mortality rate, for both men and women. We show that these calculated data are in good quantitative agreement with the actual number of Canadians that die. This agreement provides strong evidence (but not proof) that the mechanism of STLIS plays an important role in the major diseases of aging (e.g., cardiovascular disease, many cancers, and diabetes mellitus) which dominate human mortality. This result represents significant progress in our understanding the factors behind the cause of aging.