This study evaluated the use of filtration and UV-A photocatalysis for the reduction of particulate matter (PM) and airborne bacterial pathogens in swine barns. Two MERV filters (8 and 15) were used to mitigate PM concentrations measured at the PM 1, PM 2.5, respirable PM, and PM 10 ranges. Filtration was also used to generate different levels of airborne pathogens to be treated by UV-A. Results show that MERV 8 and 15 filters effectively reduced PM concentrations (96-98%) in air exhausted from a swine barn (p ranged from < 0.01 to 0.04). UV-A photocatalysis did not mitigate PM concentrations. UV-A photocatalysis treatment reduced measured colony-forming units (CFUs) by 15-95%. The CFU percent reduction was higher when airborne PM concentration was low. The numeric results suggested a real mitigation effect despite p-values that did not meet the usual statistical cut-off of <0.05 for significance due to the large variability of the CFU control samples. Normalization of measured airborne pathogen concentrations by smaller PM size range concentrations led to emerging significant treatment differences for CFUs. A significant decrease (~60% reduction; p < 0.03) in the concentration of viable airborne bacteria was shown for all PM below the 10-micron range.

Particulate matter (PM) represents an air quality management challenge for confined swine production systems. Because of the limited space and ventilation rate, PM can reach relatively high concentrations in swine barns. PM in swine barns possesses different physical, chemical, and biological characteristics than that in the atmosphere and other indoor environments. As a result, it exerts different environmental and health effects and creates some unique challenges regarding PM measurement and mitigation. Numerous research efforts have been made, generating massive data and information. However, relevant review reports are sporadic. This study aims to provide an updated comprehensive review of swine barn PM, focusing on publications since 1990. It covers various topics, including PM characteristics, sources, measurement methods, and in-barn mitigation technologies. Since PM in swine barns is of primarily biological origins, bioaerosols are reviewed in great detail. Relevant topics include bacterial/fungal counts, viruses, microbial community composition, antibiotic-resistant bacteria, antibiotic resistance genes, endotoxins, and (1→3)-β-D-glucans. For each topic, existing knowledge is summarized and discussed and knowledge gaps are identified. Overall, PM in swine barns is complicated in chemical and biological composition and highly variable in mass concentrations, size, and microbial abundance. Feed, feces, and skins constitute the major PM sources. Regarding in-barn PM mitigation, four technologies (oil/water sprinkling, ionization, alternation of feed and feeders, and recirculating air filtration) are dominant. However, none of them have been widely used in commercial barns. A collective discussion of major knowledge gaps and future research needs is offered at the end of the report.

UV-A (ca. 365 nm wavelength, a.k.a. 'black light') photocatalysis has been investigated to comprehensively mitigate odor and selected air pollutants in the livestock environment. This study was conducted to confirm the performance of UV-A photocatalysis on the swine farm. The objectives of this research were to (1) scale-up of the UV-A photocatalysis treatment, (2) evaluate the mitigation of odorous gases from swine slurry pit, and (3) test different UV sources, (4) evaluate the effect of suspended particulate matter (PM), and (5) conduct preliminary economic analyses. We tested UV-A photocatalysis at a mobile laboratory-scale capable of treating ~0.2 - 0.8 m3·s-1 of barn exhaust air. The targeted gaseous emissions of barn exhaust air were significantly mitigated (p < 0.05) up to 40% reduction of measured odor; 63%, 44%, 32%, 40%, 66%, and 49% reduction of dimethyl disulfide, isobutyric acid, butanoic acid, p-cresol, indole, and skatole, respectively; 40% reduction of H2S; 100% reduction of O3; and 13% reduction of N2O. The PM mitigation effect was not significant. Formaldehyde levels did not change, and a 21% generation of CO2 was observed. The percent reduction of targeted gases decreased as the airborne PM increased. Simultaneous chemical and sensory analysis confirmed that UV-A treatment changed the overall nuisance odor character of swine barn emissions into weaker manure odor with 'toothpaste and 'mint' notes. The smell of benzoic acid generated in UV-A treatment was likely one of the compounds responsible for the less-offensive overall odor character of the UV-treated emissions. Results are needed to inform the design of a farm-scale trial, where the interior barn walls can be treated with the photocatalyst, and foul air will be passively treated as it moves through the barn.

Particulate matter (PM) is one of the problems faced in environmental science. It has health effects on man and animals in both developed and developing countries. Research and efforts have been on it several years back. Policy statements and efforts have been published. This review paper is an added information on air pollution. In it, efforts were made in discussing these: classification, effects, methodology, case studies and source apportionment. It is hoped that this paper would contribute to existing knowledge on PM.

The transmission and analysis of data is one of the challenges of the 21st century. In the field of environmental measurement technology, existing broadband and wireless technologies have not been able to transmit data reliably and cost-effectively over long distances and in hard-to-reach places. LoRaWAN, an IoT technology, could be an energy-efficient, cost-effective and secure alternative as a narrowband technology in combination with battery-powered sensors and thus make an important contribution to the intelligent, largely wireless networking of objects, plants and machines (IoT), for example in the municipal sector. In addition to ecological and economic benefits, the quality of life in modern, intelligently networked cities can be enhanced by real time data acquisition. However, the prerequisite is that the quality of the data acquired via this method is sufficiently good. This paper therefore addresses the question of the quality of particulate matter data collected by low-cost sensors. To determine this, an SDS011 particulate matter sensor from Nova Fitness was ported to LoRaWAN. The sensor was installed next to a governmental measurement station. In a test that lasted five weeks, data from the SDS011 sensor were compared with those from the governmental station. Differences were identified and a correction approach was developed and applied. The efficiency of the approach was verified. Based on the results, it can be seen that the use of the low cost sensors has weaknesses. Problems can only be partially reduced. Nevertheless, the use of the low-cost sensors can be helpful for a flexible and cost effective collection of environmental data.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

The main objective of this work is to investigate the temporal variation of PM10 concentrations within the urban area of Athens during the years 2001-2015. For this purpose, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) is recorded for a 15-year period (2001-2015) in two different monitoring stations located in the urban area of Athens. The results show a totally different behavior of PM10 concentrations between the Athens city center and the suburban areas. It seems that in the city center the main sources of PM10 are traffic and heating systems especially during the cold period of the year. Furthermore, in the city center a significant seasonal variation was found with high concentrations during the cold period of the year and lower concentrations during the warm period of the year. Moreover, it was found that during the weekends, there is a decrease in PM10 concentrations probably due to the fact that majority of people do not use their vehicles. Finally, for both locations a significant temporal decreasing trend of the mean annual PM10 concentrations was found which indicates that during the last years, there have been improvements towards a better air quality.

Aiming at the problems of inaccurate segmentation of long object and information loss of small object in real-time semantic segmentation algorithm, this paper proposes a lightweight multi-branch real-time semantic segmentation network based on BiseNetV2. The new auxiliary branch makes full use of spatial details and context information to cover the long object in the field of view. Meanwhile, in order to ensure the inference speed of the model, the asymmetric convolution is used in each stage of the auxiliary branch to design a structure with low computational complexity. In the multi-branch fusion stage, the alignment and fusion module is designed to provide guidance information for deep and shallow feature mapping, so as to make up for the problem of feature misalignment in the fusion of information at different scales, and thus reduce the loss of small target information. In order to further improve the model’s awareness of key information, a global context module is designed to capture the most important features in the input data. The proposed network uses NVIDIA GeForce RTX 3080 Laptop GPU experiment, on the road street view data set Cityscapes and CamVid average occurring simultaneously ratio reached 77.1% and 78.4% respectively, with running speed of 127 frames/s respectively and 112 frames/s. The experimental results show that the proposed algorithm can achieve real-time segmentation and improve the accuracy significantly, showing good semantic segmentation performance

The control of the fine particle emission from the coal-fired power plants has been a big challenge in china. Either the conventional electrostatic precipitator or the fabric filter has some shortages. The electrostatic precipitator is hard to keep high efficiency for the submicron particles. The fabric filter could keep high efficiency but with very high pressure drop. One solution is to combine them together. Several types of hybrid particle collectors (HPC) combining the electrostatic precipitator and the fabric filter together have been developed and applied in a number of projects in China. In recent years, numerical simulation technology has been widely used in the design of the collectors. In this paper, an unsteady numerical model is used to investigate the particle deposition characteristics in a scale hybrid collector. The fluid field is modeled by using incompressible Navier-Stokes equations with the RNG turbulence equations. The corona discharge is solved by using a finite volume method. The particle charging is modeled by using a filed-diffusing combined model. And an unsteady cake formation model is used to simulate the filtration process.

The main objective of this work is the assessment of the annual number of hospital admissions for respiratory disease (HARD) due to the exposure to in-healable particulate matter (PM10), within the greater Athens area (GAA), Greece. Towards this aim, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) recorded in six monitoring stations located in the GAA, for a 13-year period 2001-2013, is used. Initially, a descriptive statistical treatment of PM10 concentrations took place. Furthermore, the AirQ2.2.3 software developed by the WHO was used to evaluate adverse health effects by PM10 in the GAA during the examined period. The results show that, during the examined period PM10 concentrations present a significant decreasing trend. Also, the mean annual HARD cases per 100,000 inhabitants ranged between 20 (suburban location) and 40 (city centre location). Approximately 70% of the annual HARD cases are due to city centre residents. In all examined locations, a declining trend in the annual number of HARD cases is appeared. Moreover, a strong relation between the annual number of HARD cases and the annual number of days exceeding the European Union daily PM10 threshold value was found.

No system nor standardized analytical procedures at commercial laboratories exist to facilitate and accurately measure potential viable virus contamination in feed ingredients and complete feeds globally. As a result, there is high uncertainty of the extent of swine virus contamination in global feed supply chains. Many knowledge gaps need to be addressed to improve our ability to prevent virus contamination and transmission in swine feed. This review summarizes the current state of knowledge involving: 1) the need for biosecurity protocols to identify production, processing, storage, and transportation conditions that may cause virus contamination of feed ingredients and complete feed, 2) challenges of measuring virus inactivation, 3) virus survival in feed ingredients during transportation and storage, 4) minimum infectious doses, 5) differences between using a Food Safety Objective versus a Performance Objective as potential approaches for risk assessment in swine feed, 6) swine virus inactivation from thermal and irradiation processes, and chemical mitigants in feed ingredients and complete feed, 7) efficacy of virus decontamination strategies in feed mills, 9) benefits of functional ingredients, nutrients, and commercial feed additives in pig diets during a viral health challenge, and 10) considerations for improved risk assessment models of virus contamination in feed supply chains.

(1)Background：To date, no studies have epidemiologically examined whether the concentration of particulate matter (PM) 2.5 and its ionic components is related to the prevalence of skin symptoms. Therefore, this study aimed to clarify this association in patients with allergic diseases. (2)Methods: From February 1 to May 31, 2020, we evaluated the daily prevalence of skin symptoms in outpatients with allergic diseases being treated at Fukuoka Hospital, Fukuoka, Japan, and measured the concentration of PM2.5 and its ionic components. （3）Results: Univariate analysis showed a statistically significant association between skin symptoms and the concentration of PM2.5 and the ionic components SO42-, NH4+, K+, and Mg2+, and multivariate analysis showed a statistically significant association between the daily prevalence of skin symptoms and the concentration of the ionic components SO42- or Mg2+. (4)Conclusions: Our findings indicate that the concentration of some PM2.5 ionic components may affect skin symptoms in patients with allergic diseases.

The study aimed to estimate the prevalence of respiratory symptoms and to assess respiratory health risks associated with Particulate Matter (PM) exposure among the residents of Windhoek, Namibia. Objectives: To measure particulate pollution concentration in Windhoek through monitoring of particulate matter concentration and to identify any associations between particulate pollution, individual location and respiratory health among the Windhoek resident’s. Methods: an adapted standardized self-administered questionnaire was used to collect respiratory health related data as well as previous exposure, while PM monitoring was done using ASTM D1739 reference method. Results: A high prevalence was observed for cough (43%), breathlessness (25%), and Asthma (11.2%). PM was found to be a significant risk factor for episode of cough and phlegm, while high PM exposure category had increased odds ratio for episode of phlegm and cough (OR: 2.5, 95% CI: 0.8-8.0). No association was observed between location and respiratory health outcomes. Conclusion: The study found high levels of PM concentration across all Windhoek suburbs which were above the German, American and EPA. Enactment of legislation relating to the control and monitoring of PM related emissions at point of generation is required at country and city level.

Environmental impact associated with odor and gaseous emissions from animal manure is one of the challenges for communities, farmers, and regulatory agencies. Microbe-based manure additives treatments are marketed and used by farmers for mitigation of emissions. However, their performance is difficult to assess objectively. Thus, comprehensive, practical, and low-cost treatments are still in demand. We have been advancing such treatments based on physicochemical principles. The objective of this research was to test the effect of the surficial application of a thin layer (¼"; 6.3 mm) of biochar on the mitigation of gaseous emissions (as the percent reduction, % R) from swine manure. Two types of biochar were tested: highly alkaline and porous (HAP) biochar made from corn stover and red oak (RO), both with different pH and morphology. Three 30-day trials were conducted with a layer of HAP and RO (2.0 & 1.65 kg∙m^-2, respectively) applied on manure surface, and emissions of ammonia (NH₃), hydrogen sulfide (H₂S), greenhouse gases (GHG), and odorous volatile organic compounds (VOCs) were measured. The manure and biochar type and properties had an impact on the mitigation effect and its duration. RO significantly reduced NH₃ (19-39%) and p-cresol (66-78%). H₂S was mitigated (16~23%), but not significantly for all trials. Significant (66~78%) reductions for p-cresol were observed for all trials. The phenolic VOCs had relatively high % R in most trials but not significantly for all trials. HAP reduced NH₃ (4~21%) and H₂S (2~22%), but not significantly for all trials. Significant % R for p-cresol (91~97%) and skatole (74~95%) were observed for all trials. The % R for phenol and indole ranged from (60~99%) & (29~94%) but was not significant for all trials. The impact on GHGs, isobutyric acid, and the odor was mixed with some mitigation and generation effects. However, larger-scale experiments are needed to understand how biochar properties and the dose and frequency of application can be optimized to mitigate odor and gaseous emissions from swine manure. The lessons learned can also be applicable to surficial biochar treatment of gaseous emissions from other waste and area sources.

The B169L protein (pB169L) of African swine fever virus (ASFV) is a structural protein with an unidentified function during the virus replication. The sequences of the B169L gene and the downstream B438L gene are separated by short intergenic regions. However, the regulatory mode of the gene transcription remains unknown. Here, we identified two distinct promoter regions and two transcription start sites (TSS) located upstream of the open reading frame (ORF) of B438L. Using the promoter reporter system, we demonstrated that the cis activity of the ORF proximal promoter exhibited significantly higher levels compared with that of the distal promoter located in the B169L gene. Furthermore, transfection with the plasmids with two different promoters for B438L could initiate the transcription and expression of the B438L gene in HEK293T cells, and the cis activity of the ORF proximal promoter also displayed the higher activities compared with the distal promoter. Interestingly, the B438L distal promoter also initiated the transcription of the alternatively spliced B169L mRNA (B169L mRNA2) encoding a truncated pB169L (tpB169L) (amino acids 92–169), and the gene transcription efficiency was increased upon mutation of the initiation codon located upstream of the alternatively spliced B169L gene. Taken together, we demonstrated that the distal promoter of B438L gene initiates the transcription of both the B438L mRNA and B169L mRNA2. Comprehensive analysis of the transcriptional regulatory mode of the B438L gene is beneficial for the understanding of the association of B438L protein and pB169L and the construction of the gene-deleted ASFV.

The objective of this research is to analyze metal elements like Na (sodium), Mg (magnesium), Al (aluminum), Si (silicon), Pb (lead), K (potassium), Ca (calcium), and Fe (iron) found in dust particles within two distinct areas from which the sampling has been done. First sampling was taken from the road verge of a highly trafficked road section, while the second sampling was done in a residential garden area 90 m away from the road. Several metal elements have been detected, with a high difference for Silicon Si, which present higher concentrations in the dust sampled from the road verge area. Pb has only been detected in the samples taken from the road verge, which could be explained by residual remnants from old lead gasoline, and wheel weights. Additionally, airborne particulate matter (PM) concentrations have been measured, during the same episode, in comparison between the road verge and the garden area, presenting a substantial difference in the concentration levels, deducing that dense vegetation is protecting and blocking a majority of airborne PM. A literature highlight of health effects of different metal elements and PM concentrations is presented.

Seasonal variations in atmospheric ultrafine particulate matter (PM0.1) were monitored in Bangkok, Thailand, from 2016 to 2017. PM0.1 bound organic carbon (OC), and elemental carbon (EC) were collected by a cascade air sampler that can collect PM0.1 and estimated by a thermal-optical carbon analyzer following the IMPROVE-TOR protocol. The annual average PM0.1 in Bangkok was 14.5 ± 4.7 µg/m3, higher than in large Asian cities like Shanghai and Hanoi. Biomass burning from neighboring areas was shown to increase the particle concentration. Apparent risings in carbon species as OC, EC, and OC/EC ratios in the wet and dry seasons were observed, and Char-EC/Soot-EC displayed that the PM0.1 in the Bangkok atmosphere was influenced mainly by the vehicle exhaust, even though the influence of biomass burning was more sensitive during the dry season. The effective carbon ratio (ECR) displays that carbonaceous aerosol is light-absorbing; the dry season increase contributed to climate and air quality. The finding of this work is of great importance to air pollutants control policies in urban areas.

Background: Exposure in utero to particulate matter (PM2.5 and PM10) is associated with maladaptive health outcomes. Although exposure to prenatal PM2.5 and PM10 have cord blood DNA methylation signatures at birth, signature persistence into childhood and saliva cross-tissue applicability has not been tested. Methods: In the Fragile Families and Child Wellbeing Study, a United States 20-city birth cohort, average residential PM2.5 and PM10 during pregnancy was estimated using air quality monitors with inverse distance weighting. Saliva DNA methylation at ages 9 (n=749) and 15 (n=793) was measured using the Illumina HumanMethylation 450k BeadArray. Cumulative DNA methylation scores for particulate matter were estimated by weighting participant DNA methylation at each site by meta-analysis effect estimates from Gruzieva et al. 2019 and standardizing the sums. Using mixed effects regression analysis, we tested the associations between cumulative DNA methylation scores at ages 9 and 15 and PM exposure during pregnancy, adjusted for child sex, age, race/ethnicity, maternal income to needs ratio, nonmartial birth status, and saliva cell type proportions. Results: Our study sample was 50.5% male, 56.3% non-Hispanic Black, and 19.8% Hispanic, with median income to needs ratio of 1.4. In the third trimester, mean PM2.5 exposure levels were 27.9 ug/m3/day (standard deviation: 7.0, 23.7% of observations exceeded safety standards) and PM10 were 15.0 ug/m3/day (standard deviation: 3.1). An interquartile range increase in PM2.5 exposure (10.73 g/m3/day) was associated with -0.0287 standard deviation lower cumulative DNA methylation score for PM2.5 (95% CI: -0.0732, 0.0158, p=0.20) across all participants. An interquartile range increase in PM10 exposure (3.20 g/m3/day) was associated with -0.1472 standard deviation lower cumulative DNA methylation score for PM10 (95% CI: -0.3038, 0.0095, p=0.06) across all participants. The PM10 findings were driven by the age 15 subset where an interquartile range increase in PM10 exposure was associated with -0.024 standard deviation lower cumulative DNA methylation score for PM10 (95% CI: -0.043, -0.005, p=0.012). Findings were robust to adjustment for PM exposure at ages 1 and 3. Conclusion: In utero PM10 associated DNA methylation differences persist until age 15 and can be detected in saliva. Benchmarking the persistence and cell type generalizability is critical for epigenetic exposure biomarker assessment.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Density is a crucial parameter for quantitatively describing the physical properties of liquids. It serves as an important indicator for scientific research, production process control, pipeline transportation, and other aspects. In oil pipeline transportation and raw material processing, real-time online measurement of liquid density is of great significance. This paper analyzes the working principle of an on-line vibrating tube densitometer and derives the fitting equation for temperature, pressure, and density；it also conducts experiments with an on-line vibrating tube liquid densitometer and establishes a traceability chain for the experimental device. The experimental setup includes a desktop densitometer system, a multi-temperature field constant temperature stirring system, a walk-in constant temperature box, an automatic blowing system, and a frequency acquisition and calculation system. The uncertainty of the device's evaluation is U= 0.08kg/m3, k=2.The experimental research on the on-line vibrating tube liquid densitometer can be carried out within the range of (650~1400) kg/m3, (10~70)℃, (0~50)bar the metrological performance of the vibrating tube densitometer can be researched by utilizing the straight tube type and the elbow type on-line vibrating tube densitometer. A preliminary study was conducted on the effects of different densities, temperatures, and pressures on the vibrating tube system's vibration cycle. The fit coefficient and error were calculated, and the experimental results were compared to the theoretical analysis to confirm the device's conformity. The study verified the device's scientific and reasonable design, and demonstrated that it is feasible to use the device for follow-up research.

Inhaled particulate matter (PM) is a key player in the millions of yearly deaths worldwide related to air pollution. The oxidative potential of PM provides an indication of its ability to promote an oxidative environment. When the human lungs are exposed to PM, the reactive oxygen species (ROS) generated in such oxidative environment, if excessive, may lead to cell damage via oxidative stress. Inflammation, endoplasmic reticulum stress, airway remodeling, and many different cell death modes (apoptosis, ferroptosis, pyroptosis, among others) can be triggered by oxidative stress via complex molecular pathways, which also involve the adaptive cellular response. But ROS can also directly interact with macromolecules such as proteins and lipids, as well as nucleic acids, having been reported to induce DNA damage and epigenetic modifications, which jeopardizes homeostasis. These facts have been extensively studied in in vitro models and confirmed in in vivo models.In this review, we delve beyond conventional assessments of airborne particles, discussing their oxidative potential and the PM-induced ROS-mediated cellular damage observed in in vitro models. The close link between oxidative stress and inflammation, and the manifestation of different cell death modes is highlighted by reviewing the latest literature. The effects of ROS on the balance of DNA damage and repair, carcinogenicity and epigenetics interplay are then analyzed. Finally, we expand on the latest reports on the antioxidants’ potential to counteract the deleterious effects of ROS, and disclose future perspectives for the topic.

The research is focusing on analyzing the concentrations of particulate matter (PM) next to a highly congested road section, with 39,900 as a maximum number of vehicles per 24 h, in the vicinity of Timisoara, Romania. Concentrations have been measured in multiple episodes using two different measurement methods, gravimetric and dynamic light scattering, showing a disperse range of PM concentrations. Presence of metal particles in the samples have been analyzed using an electron microscope. Additionally, impact on human health is described by evaluating results for inhalable, thoracic, and alveolar sized particles.

World Health Organization (WHO) provides the guideline for managing the Particulate Matter (PM) level because when the PM level is higher, it threats the human health. For managing PM level, the procedure for measuring PM value is needed firstly. We use Tapered Element Oscillating Microbalance (TEOM)-based PM measuring sensors because it shows higher cost-effectiveness than Beta Attenuation Monitor (BAM)-based sensor. However, TEOM-based sensor has higher probability of malfunctioning than BAM-based sensor. In this paper, we call the overall malfunction as an anomaly, and we aim to detect anomalies for the maintenance of PM measuring sensors. We propose a novel architecture for solving the above aim that named as Hypothesis Pruning Generative Adversarial Network (HP-GAN). We experimentally compare the several anomaly detection architectures to certify ours performing better.

A probe of a patient, seeking help in an emergency ward of a French hospital in late December 2019 because of Influenza like symptoms, was retrospectively tested positive to COVID-19. Despite the early appearance of the virus in Europe, the prevalence and virulence appeared to be low for several weeks, before the spread and severity of symptoms increased exponentially, yet with marked spatial and temporal differences. Here, we compare the possible linkages between peaks of fine particulate matter (PM2.5) and the sudden, explosive increase of hospitalizations and mortality rates in the Swiss Canton of Ticino, and the Greater Paris and London regions. We also discuss the influence of Saharan dust intrusions on the COVID-19 outbreak observed in early 2020 on the Canary Islands. We find that high PM2.5 concentrations – possibly favored by air temperature inversions or Saharan dust intrusions – are not only modulating but even more so boosting severe outbreaks of COVID-19. We conclude that the overburdening of the health services and hospitals as well as the high over-mortality observed in various regions of Europe in spring 2020 can be linked to peaks of PM2.5 and likely particular weather situations that have favored the spread and enhanced the virulence of the virus. In the future, we recommend to monitor not only the prevalence of the virus, but also to consider the occurrence of weather situations that can lead to sudden, very explosive COVID-19 outbreaks.

Coal-fired thermal plants (CTPP) are known to pollute the atmosphere with emission of many greenhouse gases and particulate matter. The power generation from these thermal plants cannot be stopped completely because it forms the backbone of the grid power supply. It is necessary to study the dispersion patterns of pollutants that affect the health of the people. The dispersion patterns are location specific since they depend on local meteorological conditions. In this study, the dispersion of particulate matter (PM) and sulphur dioxide (SO₂) from a CTPP with 275 m high stack are studied under different atmospheric boundary layer (ABL) of neutral, stable and unstable conditions up to a distance of 30 km from the stack. The plume of the PM spreads under all conditions. During some parts of the day, PM settles around the stack while at other times PM keeps suspending in the air for the full distance under study. Sulphur dioxide dilutes to concentrations below the detection limits in about 12-13 km from the stack for neutral and unstable ABL whereas for the stable ABL, the dispersion is up to 30 km. The 24 h weighted average concentration of sulphur dioxide, at 10 m height from the ground, is 14.2 mg/m³ at a distance of 25 kms from the CTPP, which is comparable with the value of 9.2 mg/m³ measured at the Air Quality Stations located around the same distance. Based on the results policy changes that need to be implemented are suggested.

Recent omics technologies have revolutionized the study of molecular plant responses to air pollution, overcoming previous limitations. This review synthesizes the latest advancements in molecular plant responses to major air pollutants, emphasizing ozone (O3), nitrogen oxides (NOX) and particulate matter (PM) research. These pollutants induce stress responses common to other abiotic and biotic stresses, including the activation of reactive oxygen species (ROS)-scavenging enzymes and hormone signaling pathways. New evidence showed the central role of antioxidant phenolic compound biosynthesis via phenylpropanoids pathway in air pollution stress responses. Transcription factors like WRKY, AP2/ERF, and MYB, which connect hormones signaling to antioxidant biosynthesis, were also affected. To date, research has predominantly focused on laboratory studies analyzing individual pollutants. This review highlights the need for comprehensive field studies and the identification of molecular tolerance traits, which are crucial for the identification of tolerant plant species aimed to the development of sustainable Nature Based Solutions (NBS) to mitigate urban air pollution.

In northern Thailand, the problem of small particulate matter happens every year, with the pri-mary source being agricultural weed burning and wildfire. The tourism industry is strongly impacted and has been the spotlight for the past few years. Thus, the study aims to investigate the effect of small particulate matter on tourism and related SMEs in Chiang Mai, Thailand. The data was collected from 286 entrepreneurs in the tourism and related SMEs sectors. The data was analyzed using data mining and association rule techniques. The study revealed that small particulate matter has a considerable impact on customer factors, especially the number of customers has decreased. Operational factors and prod-uct/service factors are also affected by the dust in the form of adjustments to keep the business running and the protection of the health of employees and customers. Certainly, financial factors are affected by the small particulate matter situation, both lower revenues and higher costs.

Both, in developed and developing countries, atmospheric pollution with particulate matter (PM) remains an important issue. Despite the health effects of poor air quality, studies on air pollution are often limited by the high costs of continuous monitoring and the need of extensive sampling. Furthermore, these particles are often enriched in potentially toxic trace elements and organics pollutants. This study evaluates both, the composition of atmospheric dust accumulated during a certain time-span on leaves of Hedera helix and Senecio cineraria, as well as the potential to use them as bio-monitors. The test plants were positioned nearby automatic air quality monitoring stations at four different sites with respectively high, moderate and low traffic intensity. Gravimetric deposition of PM10 and PM2.5 on leaves was consistent with data recorded by the monitoring stations and related to the weather conditions reported by Argentina´s National Meteorological service. To determine the presence of trace elements enriching the PM deposited on leaves, two analytical techniques were applied, XRF (not destructive) and ICP (destructive). The results indicated that only in the unpaved street location (site 2), PM10 and PM2.5 concentrations in the air exceeded WHO guidelines. However, several trace elements were found enriching PM deposited on leaves from all sites. Predominantly, increased concentrations of Cd, Cu, Ti, Mn, Zn and Fe were found, which were associated to construction, traffic and unpaved street sources. Furthermore, based on its high capability to sequester PM and trace elements Senecio cineraria can be take into consideration to be adopted as a bio-monitor or even for PM mitigation.

The risk of inhalation exposure to elevated concentrations of hydrogen sulfide (H₂S) and ammonia (NH₃) during the agitation of stored swine manure is high. Once or twice a year, farmers agitate manure before pump-out and application to fields. Agitation of the swine manure causes the short-term releases of highly toxic levels of H₂S and NH₃. In our previous pilot-scale studies, the biochar powder had shown significant mitigation of H₂S and NH₃ emissions when surficially applied to manure immediately before agitation. However, fine biochar powder application poses hazards by itself and may not be practical to apply on a farm scale, especially when livestock and workers are present. We hypothesized that applying pelletized biochar to manure surface is just as effective as applying powder to protect farmers and animals from excessive exposure to H₂S and NH₃. This work reports on the lab-scale proof-of-the-concept trials with biochar pellets on the lab-scale. The objective was to compare the biochar pellets and biochar powder on their effectiveness of mitigation on H₂S and NH₃ gases during 3-hour long swine manure agitation. Three scenarios were compared in (n=3) trials (i) control, (ii) 12.5 mm thick surficial application to manure surface of biochar powder, and (iii) an equivalent (by mass) dose of pelletized biochar applied to manure surface. The biochar powder was bound with 35% (wt) water into ~5 × 10 mm (dia × length) pellets. Biochar powder was significantly (p<0.05) more effective than the biochar pellets. Still, pellets reduced total H₂S and NH₃ emissions by ~72% and ~68%, respectively (p=0.001), compared with ~99% by powder (p=0.001). The maximum H₂S & NH₃ concentrations were reduced from 48.1±4.8 ppm & 1,810±850 ppm to 20.8±2.95 ppm & 775±182 ppm by pellets, and to 22.1±16.9 ppm & 40.3±57 ppm by powder, respectively. These reductions are equivalent to reducing the maximum concentrations of H₂S and NH₃ during the 3-h manure agitation by 57% and 57% (pellets) and 54% and 98% (powder), respectively. Treated manure properties hinted at improved nitrogen retention, yet not significant due to high variability. We recommend scaling-up and trials on the farm-scales using biochar pellets to assess the feasibility of application to large manure surfaces and techno-economic evaluation.

Today, air pollution is the greatest threat to organismal healthspan. The environment of our planet earth, the habitat of over eight billion humans and estimated twenty billion billions other animals, is contaminated with a wide variety of pollutants. Unfortunately, humans, out of billions and billions of living organisms on earth, are solely responsible for polluting the environment through emitting pollutants like particulate matter from industry, fuel engine vehicles, biomass combustion, toxic fumes from blasting, and wildfire. In the modern world, human-caused air pollutants induce massive oxidative stress and inflammation, the major contributors in initiation and progression of many diseases including pulmonary, cardiovascular, renal, hepatic, reproductive, neurological, mental, and accelerated biological aging. The provocative question is the following: how can we solve this human-created problem? As it is not realistic to clean the environment at once from human-caused pollution, initiatives have been undertaken to develop novel therapeutic approaches to control air-pollutant-induced oxidative stress and inflammation to protect humans from pollution-induced devastating diseases. In this article, I discuss the key findings of numerous recent preclinical studies documenting first, the role of air pollutant PM2.5 in augmentation of inflammation, oxidative stress, and associated diseases; and second, the efficacies of different natural and synthetic compounds in amelioration of PM2.5-induced oxidative stress, inflammation, pyroptosis, and associated pathologies.

Every day around 93% of children under the age of 15 (1.8 billion children) breathe outdoor air that is so polluted it puts their health and development at serious risk. Due to the pandemic, however, ventilation of buildings using outdoor air has become an important safety technique to prevent the spread of COVID-19. With the mounting ev-idence suggesting that air pollution is impactful to human health and educational out-comes, this contradictory guidance may be problematic in schools with higher air pol-lution levels, but keeping kids COVID-19 free and in school to receive their education is now more pressing than ever. To understand if all schools in an urban area are ex-posed to similar outdoor air quality and if school infrastructure protects children equally indoors, we installed research grade sensors to observe PM2.5 concentrations in indoor and outdoor settings to understand how unequal exposure to indoor and out-door air pollution impacts indoor air quality among high- and low-income schools in Salt Lake City, Utah. Based on this approach, we found that during atmospheric inver-sions and dust events, there was a lag ranging between 35 to 73 minutes for the out-door PM2.5 concentrations to follow a similar temporal pattern as the indoor PM2.5. This lag has policy and health implications and may help to explain the rising concerns re-garding reduced educational outcomes related to air pollution in urban areas. These data and resulting analysis show that poor air quality may impact school settings, and the potential implications with respect to environmental inequality.

As broiler farming facilities have become larger and more concentrated in response to external environmental changes, there is a possibility of increased concentrations of fine dust and aerosols inside these facilities due to enclosure. In particular, workers are exposed to high concentrations of organic particulate matter and harmful gases while performing their tasks, and as they age, they become more vulnerable to respiratory diseases. It is essential to directly monitor the concen-trations to which workers are exposed, along with the spatial distribution of aerosols inside broiler house. In this study, we analyzed the regional aerosol concentrations using passive samplers in commercial tunnel-ventilated broiler farms. Simultaneously, we employed active samplers at the height of the workers' breathing zones to monitor real-time aerosol concentrations by particle size along their work routes. Spatial aerosol concentrations generally increased from the inlet to the exhaust in the breathing zone. The average aerosol concentrations were TSP -1,042 µg/m³, PM-10 718 µg/m³, and PM-2.5 137 µg/m³. To analyze the workers' exposure environments, we categorized the tasks in the barn into Static work period (SWP) and Moving work period (MWP) based on video analysis. The results showed that during MWP, fine dust concentrations exceeded the standards by up to 214%. Particularly, during MWP, the concentrations were 1.74 times higher for TSP, 1.40 times higher for PM-10, and 1.22 times higher for PM-2.5 compared to SWP. It was observed that during the movement of workers, physical generation of particles around 10 µm, such as feces, feed, and bedding, occurred due to the movement of chicken, which influenced the aerosol concentration.

The rural communities are affected by gaseous emissions from intensive livestock production. Practical mitigation technologies are needed to minimize emissions from stored manure and improve air quality inside barns. In our previous research, the one-time surficial application of biochar to swine manure significantly reduced emissions of NH3 and phenol. We observed that the mitigation effect decreased with time during the 30-day trials. In this research, we hypothe-sized that bi-weekly reapplication of biochar could improve the mitigation effect on a wider range of odorous compounds using larger scale and longer trials. The objective was to evaluate the effectiveness of biochar dose and reapplication on mitigation of targeted gases (NH3, odor-ous VOCs, odor, GHGs) from stored swine manure on a pilot-scale setup over 8-weeks. The bi-weekly reapplication of the lower biochar dose (2 kg/m2) showed much higher significant percent reductions of emissions for NH3 (33% without & 53% with reapplication) and skatole (42% without & 80% with reapplication), respectively. In addition, the reapplication resulted in the emergence of statistical significance to the mitigation effect for all other targeted VOCs. Spe-cifically, for indole, the % reduction improved from 38% (p=0.47, without reapplication) to 78% (p=0.018, with reapplication). For phenol, the % reduction improved from 28% (p=0.71, without reapplication) to 89% (p=0.005, with reapplication). For p-cresol, the % reduction improved from 31% (p=0.86, without reapplication) to 74% (p=0.028, with reapplication). For 4-ethyl phenol, the percent emissions reduction improved from 66% (p=0.44, without reapplication) to 87% (p=0.007, with reapplication). The one-time 2 kg/m2 and 4 kg/m2 treatments showed similar effectiveness in mitigating all targeted gases, and no statistical difference was found between the dosages. The one-time treatments showed significant % reductions of 33% & 42% and 25% & 48% for NH3 and skatole, respectively. The practical significance is that the higher (one-time) biochar dose may not necessarily result in improved performance over the 8-week manure storage, but the bi-weekly reapplication showed significant improvement in mitigating NH3 and odorous VOCs. The lower dosages and the frequency of reapplication on the larger-scale should be explored to optimize biochar treatment and bring it closer to on-farm trials.

ω-Transaminases have been immobilized on macrocellular silica monoliths and used as heterogeneous biocatalysts in a continuous flow mode enantioselective transamination reaction. The support was prepared by a sol-gel method based on emulsion templating. The enzyme was immobilized on the structured silica monoliths both by adsorption, and by covalent grafting using amino-functionalized silica monoliths and glutaraldehyde as a coupling agent. A simple reactor set-up based on the use of a heat-shrinkable Teflon tube is presented and successfully used for the continuous flow kinetic resolution of a chiral amine, 4-bromo-α-methylbenzylamine. The porous structure of the supports ensures effective mass transfer and the reactor works in the plug flow regime without preferential flow paths. When immobilized in the monolith and used in the flow reactor, transaminases retain their activity and their enantioselectivity. The solid biocatalyst is also shown to be stable both on stream and during storage. These essential features pave the way to the successful development of an environmentally friendly process for chiral amines production.

Understanding the relationships between land cover/urban structure patterns and air pollutants is key to sustainable urban planning and development. In this study, we employ a mobile monitoring method to collect PM_2.5 and BC data in the city of Philadelphia, PA during the summer of 2019 and apply the Structure of Urban Landscapes (STURLA) methodology to examine relationships between urban structure and atmospheric pollution. We find that, while PM_2.5 and BC vary by STURLA class, many of the differences in pollutant concentrations between classes are not significant. However, we also find that the proportions in which STURLA components are present throughout the urban landscape can be used to predict urban air pollution. Among frequently sampled STURLA classes, gpl hosted the highest PM_2.5 concentrations on average (16.60 _± 4.29 µg/m³), while tgbwp hosted the highest BC concentrations (2.31 _± 1.94 µg/m³). Furthermore, STURLA combined with machine learning modeling was able to correlate PM_2.5 (R²= 0.68, RMSE 2.82 µg/m³) and BC (R² = 0.64, RMSE 0.75 µg/m³) concentrations with the urban landscape and spatially interpolate concentrations where sampling did not take place. These results demonstrate the efficacy of the STURLA methodology in modeling relationships between air pollution and land cover/urban structure patterns.

The normal growth and development of skeletal muscle is essential for the health of the body. The regulation of skeletal muscle by intestinal microorganisms and their metabolites has been continuously revealed. Acetate is the predominant short-chain fatty acid synthesized by gut microbiota through the fermentation of dietary fiber, however, the underlying molecular mechanisms governing the interaction between acetate and skeletal muscle during rapid growth stage remain to be further elucidated; Here, specific pathogen-free (SPF) mice, germ-free (GF) mice, and germ-free mice supplemented with sodium acetate (GS) were used to evaluate the effects of acetate on skeletal muscle growth and development of young mice with gut microbiota deficiency; We found the concentration of serum acetate, body mass gain, succinate dehydrogenase activity and expression of myogenesis maker gene of skeletal muscle in the GS group was higher than GF group following sodium acetate supplement. Furthermore, the transcriptome analysis revealed that acetate activated biological processes regulating skeletal muscle growth and development in GF group that are inhibited due to gut microbiota deficiency. In vitro experiment, we proved that acetate up-regulated Gm16062 to promote skeletal muscle cell differentiation; Overall, our findings proved that acetate promote skeletal muscle growth and development in young mice via increase Gm16062 expression.

Urban air pollution is a significant threat to both the environment and public health. Primarily originating from traffic emissions, particulate matter is identified as the most prevalent and toxic pollutant in cities. In recent years, street vegetation has emerged as a nature-based solution to improve urban air quality. However, to achieve this goal, proper placement of vegetation is crucial. This study critically investigates how different street tree placement strategies affect the local air quality, based on a model calibrated using existing air quality measurements from one of the most polluted streets in Glasgow. We then test the local air quality effects of tree orientation, spacing, shape, porosity, size, species, and wind directions. The findings suggest that trees effectively enhance air quality, particularly when implemented on the leeward side of the street. To achieve optimal effectiveness, the spacing of trees require careful alignment with the aspect ratio, as haphazard planting could lead to unfavorable results. The insights on improving air quality in Glasgow's street canyons, complements the objectives of the ‘Glasgow Avenues Programme’ and can be included in its Low Emission Zones to co-benefit the environment and the wellbeing of the local community.

This paper describes the indoor air pollution in urban (Lahore, Faisalabad, Gujranwala, Rawalpindi and Karachi) Pakistani regions while considering the outdoor air and the health and wellbeing of the occupants present indoors. It also aims to assess previous methodological approaches Such as Air Conditioning Systems, used by developed countries to improve air quality to demonstrate the improvements that can be made in air quality in Pakistani urban areas. This research also investigates the causes, concentration and effects of poor air quality in Pakistani urban areas such as particulate matter (PM2.5), carbon oxides (COx), nitrogen oxides (NOx), sulphur oxides (SOx) and volatile organic compounds (VOC’s). The average concentration of these pollutants in Pakistan’s indoor air is, particulate matter (PM): [100 – 250 µg/m3 for PM2.5, 200 – 600 µg/m3 for PM10] 1 – 20 ppm for carbon monoxide (CO), nitrogen oxides (NOx): [50 – 100 µg/m3 for NO2, 20 – 40 µg/m3 for NO], 20 – 50 µg/m3 for sulfur dioxide (SO2), volatile organic compounds (VOCs): 0.1 – 0.5 ppm for formaldehyde, 5 – 10 µg/m3 for benzene and 20 – 30 µg/m3 for toluene. It should be noted that these concentrations can differ depending on the origin of pollution, location, and time of day. The literature review is made up of a combination of descriptive research methods that are used to inform the research background of ambient and indoor air quality, thus the literature review provides a theoretical and methodological background about the air pollution and its improvement in different parts of the world. According to the World Air Quality Index, Pakistan is the third most polluted country in terms of average PM2.5 concentration which is 14.2 times the WHO annual air quality guideline value. As a result, it is suggested that a PM2.5 concentration reduction program be implemented in urban Pakistani regions' indoor air.

Currently available nationwide prediction models for fine particulate matter (PM_2.5) lack prediction confidence intervals and usually do not describe cross validated model performance at different spatiotemporal resolutions and extents. We used 41 different spatiotemporal predictors, including data on land use, meteorology, aerosol optical density, emissions, wildfires, population, traffic, and spatiotemporal indicators to train a machine learning model to predict daily averages of PM_2.5 concentrations at 0.75 sq km resolution across the contiguous United States from 2000 through 2020. We utilized a generalized random forest model that allowed us to generate asymptotically-valid prediction confidence intervals and took advantage of its usefulness as an ensemble learner to quickly and cheaply characterize leave-one-location-out CV model performance for different temporal resolutions and geographic regions. Using a variable importance metric, we selected 8 predictors that were able to accurately predict daily PM_2.5, with an overall leave-one-location-out cross validated median absolute error of 1.20 ug/m³, an R² of 0.84, and confidence interval coverage fraction of 95%. When considering aggregated temporal windows, the model achieved leave-one-location-out cross validated median absolute errors of 0.99, 0.76, 0.63, and 0.60 ug/m³ for weekly, monthly, annual, and all-time exposure assessments, respectively. We further describe the model’s cross validated performance at different geographic regions in the United States, finding that it performs worse in the Western half of the country where there are less monitors. The code and data used to create this model are publicly available and we have developed software packages to be used for exposure assessment. This accurate exposure assessment model will be useful for epidemiologists seeking to study the health effects of PM across the continental United States, while possibly considering exposure estimation accuracy and uncertainty specific to the the spatiotemporal resolution and extent of their study design and population.

In higher education, the cultivation of research competency is pivotal for students’ critical thinking development and their subsequent transition into the professional workforce. While statistics plays a fundamental role in supporting the completion of a research project, it is often perceived as challenging, particularly by students in majors outside mathematics or statistics. The connection between students’ statistical proficiency and their research competency remains unexplored despite its significance. To address this gap, we utilized the supervised machine learning approach to predict students’ research competency, as represented by their performance in a research methods class, with predictors of students’ proficiency in statistical topics. Predictors relating to students’ learning behavior in a statistics course such as assignment completion and academic dishonesty are also included as auxiliary variables. Results indicate that the three primary categories of statistical skills—namely, understanding of statistical concepts, proficiency in selecting appropriate statistical methods, and statistics interpretation skills— can be used to predict students’ research competency, as demonstrated by their final course scores and letter grades. This study advocates for strategic emphasis on the identified influential topics to enhance efficiency in developing students’ research competency. Findings could inform instructors in adopting a strategic approach to teaching the statistical component of research for enhanced efficiency.

Particulate matter (PM) contains heavy metals that affect various cellular functions and gene expression associated with an array of acute and chronic diseases, in humans. However, their specific effects on the stem cells remain unclear. Here, we report the effects of PM collected from Jeddah city on bone marrow mesenchymal stem cells (BM-MSCs) on proliferation, cell death, related gene expression and systems biological analysis aiming to understand the underlying mechanisms. Two different sizes (PM_2.5-₁₀) were tested in vitro at various concentrations (15 to 300 µg/ml) and durations (24 to 72 h). PMs induced cellular stress including membrane damage, shrinkage and death. Lower concentrations of PM_2.5 increased BM-MSCs proliferation, while higher concentrations decreased it. PM₁₀ decreased BM-MSCs proliferation in a concentration-dependant manner. The X-Ray Fluorescence spectrometric analysis showed that PM contains high levels of heavy metals. Ingenuity Pathway Analysis (IPA) and hierarchical clustering analyses showed that heavy metals were associated with signalling pathways involving cell stress/death, cancer and chronic diseases. qRT-PCR results showed differential regulation of the apoptosis genes (BCL2, BAX); upregulation of inflammation associated genes (TNF-a and IL-6) and downregulation of cell cycle regulation gene (P53). We conclude that PM could affect different cellular functions and predispose to debilitating diseases.

This study aims to elucidate the influence of meteorological conditions on particle levels in Cergy-Pontoise. It explores the temporal variability of PM10 pollution days by associating them with the vertical temperature profile derived from conventional radiosondes from 2013 to 2022 (regional station). The results indicate that nearly 80% of exceedance days were associated with thermal inversions, primarily observed in winter and typically lasting 1 to 3 days. Analysis of winter thermal inversion characteristics suggests that those linked to pollution primarily occur near the ground, with higher intensity in December (12.1°C) and lower in February (10.3°C). Persistent inversions (extended nocturnal by diurnal inversion) account for 91.4% of the total inversions associated with high concentrations. Captive balloon soundings and temperature measurements at different altitudes were conducted during the winter of 2022/2023 to clarify thermal inversion in the Oise Valley at the center of Cergy-Pontoise. The results highlight three nocturnal wind circulation mechanisms in the valley, including downslope flow, circulation influenced by an urban heat island, and mechanical air evacuation under an inversion layer towards the less steep East side of the valley. Analysis of PM with the temperature gradient in the Oise Valley shows a significant correlation, suggesting an increase in concentrations during locally detected inversions and a decrease during atmospheric disturbance.

Polycyclic aromatic hydrocarbons (PAHs) have been reported to cause oxidative stress in metabolic processes. This study aimed to evaluate the relationship between exposure to PAHs, including benzo[a]pyrene (BaP) and 1-nitropyrene (1-NP), in the atmosphere and oxidative stress levels in the human body. This study included 44 Korean adults who lived in Cheongju, South Korea. Atmospheric BaP and 1-NP concentrations and urinary 6-hydroxy-1-nitropyrene (6-OHNP), N-acetyl-1-aminopyrene (1-NAAP), and 1-hydroxypyrene (1-OHP) concentrations were measured. The oxidative stress level was assessed by measuring urinary thiobarbituric acid reactive substances (TBARS) and 8-hydroxydeoxyguanosine (8-OHdG) concentrations. Urinary TBARS and 6-OHNP concentrations significantly differed between winter and summer. BaP exposure was significantly associated with urinary 8-OHdG concentrations in summer. However, atmospheric 1-NP did not show a significant correlation with oxidative stress marker concentrations. Urinary 1-NAAP concentration was a significant determinant for urinary 8-OHdG concentration in summer. Oxidative stress in the body increases in proportion to inhalation exposure to BaP, and more 8-OHdG is produced in the body as the amount of 1-NP, which is metabolized to 1-AP or 1-NAAP, increases.

Saussurea neoserrata Nakai offers a reliable and efficient source of antioxidants that can help alleviate adverse skin reactions triggered by air pollutants. Air pollutants, such as particulate matter (PM), have the ability to infiltrate the skin and contribute to the higher occurrence of cardiovascular, cerebrovascular, and respiratory ailments. Individuals with compromised skin barriers are particularly susceptible to the impact of PM since it can be absorbed more readily through the skin. This study investigated the impact of protocatechuic acid and syringin, obtained from the n-BuOH extract of S. neoserrata Nakai, on the release of PGE₂ and PGD₂ induced by PM₁₀. Additionally, it examined the gene expression of enzymes involved in the synthesis of PGE₂ and PGD₂ in human keratinocytes. The findings of this research highlight the potential of utilizing safe and efficient plant-derived antioxidants in dermatological and cosmetic applications to mitigate the negative skin reactions caused by exposure to air pollution.

Several studies have identified a relationship between air pollution and depression, particularly in relation to fine particulate matter (PM2.5) exposure. However, the strength of this association appears to be moderated by variables such as age, gender, genetic vulnerability, physical activity and climatic conditions, and has not been assessed at a cross-national level to date. The current study examines the association between the prevalence of depression in each country, based on the most recent Global Burden of Disease Study data, and the average national level of PM2.5 based on the World Health Organization’s database. The observed associations were adjusted for age, gender, level of physical activity, income, education, population density, climate, and type of depression. It was observed that there was a modest but significant positive correlation between PM2.5 level and the prevalence of depression even after adjusting for the above confounders. This association was more marked above a certain threshold and applied chiefly to major depressive episodes. These findings are of significant public health importance in terms of preventive strategies aimed at reducing the population-level burden of depression.

This study presents a comprehensive assessment of indoor particulate matter (PM) concentrations, focusing on PM1, PM2.5, and PM10 in five Primary Health Centers (PHCs): Arakale, Federal College of Agriculture (FECA), Iju, Oba-Ile, and Owode within Akure Local Government Areas in Nigeria. The primary novelty of this research lies in its detailed exploration of the toxicity potential of these PM fractions, providing valuable insights into the local air quality and associated health risks. The study assesses the health implications by calculating the toxicity potential (TP), Relative Risk (RR), Excess Risk (ER), and Attributable Fractions (AF) for cardiopulmonary and lung cancer mortality. The results reveal varying RR values for all-cause mortality, with Arakale showing a slight elevation (RR: 1.061), indicating potential health risks. ER values for cardiopulmonary mortality range from 14.728±7.25 to 19.04±0.38, emphasizing the substantial excess risk associated with long-term PM2.5 exposure. The study also uncovers AF for cardiopulmonary mortality ranging between 11.03±0.31 to 19.22±0.04, underscoring the significant contribution of PM to cardiovascular and respiratory health risks. Similarly, AF for lung cancer mortality ranges from 10.03±0.012 to 17.13±0.10, highlighting the substantial association between PM2.5 exposure and lung cancer risk. These findings underscore the urgent need for targeted air quality management strategies and public health interventions in the studied locations to mitigate the heightened health risks associated with particulate matter pollution. The calculated RR, ER, and AF values offer crucial insights into the complex relationship between PM exposure and adverse health outcomes, providing a foundation for informed decision-making and future research endeavors.

The tricellular tight junction protein angulin-1/lipolysis-stimulated lipoprotein receptor (LSR) is associated with numerous signal transduction pathways that regulate gene expression, epithelial cell function, and morphogenesis. The impacts of particulate matter on LSR and asthma are not known. Therefore, the aim of the present study was to assess the impacts of particulate matter as one of air pollution on LSR expression in asthma. To this end, we investigated the involvement of LSR in the pathogenesis of bronchial asthma in an ovalbumin (OVA) mouse model of asthma exposed to titanium dioxide (TiO2), and examined plasma LSR levels and their relationship with clinical variables in asthma patients and healthy controls. Plasma LSR levels were lower in asthma patients than in healthy controls. Although plasma levels of receptor for advanced glycation end-products (RAGE) were lower in asthma patients than in healthy controls, high mobility group box protein 1 (HMGB1) levels did not differ between these groups. In asthma patients, LSR levels were correlated with the forced vital capacity percentage, ratio of forced expiration (first second)-to-forced vital capacity, white blood cell count, and blood lymphocyte proportion. In mice, LSR expression was significantly decreased in OVA mice compared with control mice, and changed in OVA mice exposed to TiO2. Transforming growth factor beta levels were increased in OVA mice compared with control mice, and changed in OVA mice exposed to TiO2. Overall, plasma LSR levels were decreased in asthma patients, and were influenced by exposure to air pollution. These findings suggest the involvement of LSR in the pathogenesis of asthma.

Keywords:

Using multi-color flow cytometry analysis, we studied the immunophenotypical differences between leukemic blasts/LSCs from patients with AML/MDS and hematopoietic stem and progenitor cells (HSPCs) from patients in complete remission (CR) following their successful treatment. The panel of markers included CD34, CD38, CD45RA, CD123 as representatives for a hierarchical hematopoietic stem and progenitor cell (HSPC) classification as well as programmed death ligand 1 (PD-L1). Rather than restricting the evaluation on a 2- or 3-dimensional analysis, we applied a t-distributed stochastic neighbor embedding (t-SNE) approach to get a deeper insight and segregation between leukemic and normal HPSCs. For that purpose, we created a t-SNE map, which resulted in the visualization of 27 cell clusters based on their similarity concerning the composition and intensity of antigen expression. Two of these clusters were “leukemia-related” containing a great proportion of CD34⁺/CD38^- hematopoietic stem cells (HSCs) or CD34⁺ cells with a strong coexpression of CD45RA/CD123, respectively. CD34⁺ cells within the latter cluster were also highly positive for PD-L1 reflecting their immunosuppressive capacity. Beyond this proof of principle study, the inclusion of additional markers will be helpful to refine the differentiation between normal HSPCs and leukemic cells, particularly in the context of minimal disease detection and antigen-targeted therapeutic interventions. Furthermore, we suggest a protocol for the assignment of new cell ensembles in quantitative terms, via a numerical value, the Pearson coefficient, based on a similarity comparison of the t-SNE pattern with a reference.

The escalating prevalence of particulate matter (PM) has raised serious concerns regarding its detrimental effects on human health. This study aimed to investigate the potential of fermented blueberry and black rice (FBBR) in mitigating the effects of PM2.5, both in SH-SY5Y cells and mice exposed to PM2.5. Various assays, including MTT, NO, western blot, ELISA, and behavioral studies (MWM and Y-maze) were conducted. Our results demonstrated that PM2.5 induced significant cytotoxicity and elevated nitric oxide (NO) production at a concentration of 100μg/mL of PM2.5 in SH-SY5Y cells. Additionally, administration of FBBR effectively attenuated PM2.5-induced cytotoxicity and suppressed NO production in SH-SY5Y cells. In an intranasal instilled mice model, exposure to 10 mg/kg body weight of PM2.5 resulted in cognitive impairments. However, FBBR treatment ameliorated these impairments in both the Y-maze and MWM tests in PM2.5-exposed mice. Furthermore, FBBR administration increased the expression of brain-derived neurotrophic factor (BDNF) and reduced inflammatory markers in the brains of PM2.5-exposed SH-SY5Y cells. These findings underscore the detrimental effects of PM2.5 on the nervous system and highlight the potential of FBBR as a nutraceutical agent for mitigating these effects. Overall, this study emphasizes the urgency of addressing the harmful impact of PM2.5 on the nervous system and suggests the promising role of FBBR as a protective intervention against the adverse effects associated with PM2.5 exposure.

Magnetic quantum oscillations (MQO) are traditionally applied to investigate the electronic structure of metals. In layered quasi-two-dimensional (Q2D) materials the MQO have several qualitative features giving additional useful information, provided their theoretical description is developed. Within the framework of the Kubo formula and the self-consistent Born approximation, we reconsider the phase of beats in the amplitude of Shubnikov oscillations of interlayer conductivity in Q2D metals. We show that the phase shift of beats of the Shubnikov (conductivity) oscillations relative to the de Haas - van Alphen (magnetization) oscillations is larger than expected previously and, under certain conditions, can reach the value of π/2, as observed experimentally. We explain the phase inversion of MQO during the 3D - 2D crossover and predict the decrease of relative MQO amplitude of interlayer magnetoresistance in a strong magnetic field, larger than the beat frequency.

The main challenge in milk production has been to maintain a focus on efficient processes that enhance production outcomes, while aligning with animal welfare and sustainability and being valued by society. As an alternative to improve cow welfare in production and provide better handling of the waste generated by the activity, the system called compost-bedded pack barn (CBP) is an alternative that has been widely adopted in countries with temperate climates and higher milk production. This CBP has been attracting global interest, including from countries with tropical and subtropical climates, such as Brazil, where many producers have started to use it due to the response in terms of milk productivity. A CBP can be designed either in a) an open facility with natural ventilation or positive pressure ventilation system or b) totally closed facilities, equipped with negative pressure ventilation systems and permanent thermal control. The latter system is being implemented in Brazil, despite insufficient knowledge about its efficiency. The objective of this study was, through a review, to gather and describe the most recent information on the use of open and closed CBP systems for dairy cattle housing, mainly how it is applied in tropical climate regions. To achieve the proposed objective, this review study included the following topics related to CBPs: (i) implementation; (ii) bedding; (iii) general construction and architectural characteristics; iv) ambient thermal conditioning. Knowledge gaps and directions for future research are also identified.

المستخلص تصنيع لقاح مكون من الحمض النووي الريبوزي الرسول الخاص بالبروتينات المسئولة عن انتاج البروتينات نيورامنيديز والهيم اجليوتونين لفيروسي الانفلونزا الخنازير والطيورمحاط بجزيئات دهنية بحجم النانوميتر عدوى انفلونزا الخنازير وانفلونزا الطيور مشكلة خطيرة تؤرق العالم كله هذه الايام خصوصا انها مميتة لكثير من اطفال العالم . بعد فترة التعافي من الاصابة تتكون المناعة المكتسبة ضدها لمدة عام تقريبا. هذه الانفلونزا تسبب تسمم فيروسي في الدم بالاضافة للالتهاب الرئوي وهذامن بين اكبرالاسباب للوفاة بين الاطفال قبل سن عامين عالميا بشكل مباشر. الهدف من الدراسة هو انتاج لقاح الحمض النووي الريبوزي الرسول من نوع الام بالنانوتكنولوجي لبروتينات الهيم اجليوتونين والنيورامنيديز الموجودة على سطح هذه الفيروسات التي تساعدتها في الاتصاق بالعائل الذي ستتكاثر داخل خلاياه بالجهاز التنفسي. هذه الدراسة دراسة استكشافية ومن خلالها استطاعنا تصميم هذا اللقاح باستعمال نظام توصيل للقاح بالنانوتكنولوجي حجم جزيئاته 70نانوميمتر. اللقاح الجديد اظهر فاعلية بنسبة 60% واظهر فاعلية حيوية مقاربة واثار جانبية اقل بالمقارنة باللقاحات المتوفرة حاليا بالسوق الدوائي ضد هذا النوع من الفيروسات الوبائية. ABSTRACT Background: Worldwide, Swine and Avian influenza, or the H1N1 and H5N1 serotypes of the Influenza A virus, is a highly contagious illness. In recent years, the global incidence of mortality rate has surpassed 284,000 fatalities. Aim of the study: The production of mRNA vaccine lipid nanoparticles (LNP) to combat the deadly strains of Avian and Swine influenza (H1N1 and H5N1 of the influenza A serotype). Methodology: Polymerase chain reaction (PCR) was used to clone genes of interest encoding Haemagglutinin (HA) and Neuraminidase (NA) of Influenza A virus strains (H5N1 and H1N1) known as Avian flu and Swine flu, respectively. The genes were then inserted using the EcoR1, BAM Hind II restriction endonuclease type II, and Ligase enzyme into the pET-21(+) transcription vector plasmid. On the other hand, the hybrid transcription vectors were mixed with T7 RNA polymerase and ribonucleotides within a test tube after being linearized using EcoR II. Following their purification via reversed-phase high-performance liquid chromatography (RP-HPLC), the mRNAs of the HA and NA were encased in 70 nm LNPs and subjected to reverse-phase high-performance liquid chromatography (RP-HPLC). Lastly, immunogenicity studies were performed in stages 1/2 of randomized human and preclinical clinical trials. Results: The bivalent vaccination had around 63% efficacy in preclinical studies and approximately 60% efficacy in randomized human clinical trials. As shown by the ELISA test, strong neutralizing antibodies against HA were prevalent. Conclusion: The current study is a promising effort because of the development of the novel LNP-mRNA vaccine, which could lower the incidence of Avian and Swine flu infectious disorders.

This publication aims to disseminate a step-by-step process that walks through the conceptualization and building of a low-cost (~ $150 monitoring device for airborne fine particulate matter (PM2.5), based on miniaturized sensors and components. Details on the implementation of the hardware and software are provided which facilitate the data acquisition, capture and analysis. The central components and their setup discussed in what follows include: the sensor device (called “P.ALP” – Ph.D. Air quality Low-cost Project), Arduino IDE (Integrated Development Environment) and R code (open-access software). A monitoring device for PM2.5, using low-cost sensors and technologies was successfully conceptualized, designed, and implemented. The P.ALP monitoring system was designed and developed to be a basic device, which can be further customized and implemented using the wide range of low-cost sensors available on the market.

In this study, we adopt a unique approach by utilizing the responses of human autonomic systems to gauge the abundance of pollutants in inhaled air. Air pollution has numerous impacts on human health on a variety of time scales. This study uses biometric observations of the human autonomic response on the second timescale to investigate how the human body autonomically responds to inhaled pollutants in microenvironments, including particulate matter. PM1 and PM2.5, carbon dioxide (CO2), nitrogen dioxide (NO2), and nitric oxide (NO) on small temporal and spatial scales. These pollutants are exemplars of the wider human exposome. We compare two experimental approaches that use a similar methodology, employing a biometric suite to capture the physiological responses of cyclists and sensors to monitor the pollutants in the air surrounding them. We employ machine learning algorithms to estimate the levels of these pollutants and decipher the body’s automatic reactions to them. We observed high precision in predicting PM1, PM2.5 and CO2 using a limited set of biometrics from participants. Although the predictions for NO2 and NO were reliable at lower concentrations, the precision varied throughout the data range. This discrepancy suggests the potential to improve our models with more comprehensive data collection or advanced machine learning techniques.

The purpose of this study is to characterize atmospheric pollution and its sources in two West African urban sites during the dry season (January 2009 in Bamako, Mali, and December 2009 in Dakar, Senegal). Particulate Matter (PM) source apportionment was performed using Principal Component Analysis (PCA) and Positive Matrix Factorization (PMF). Carbonaceous components, water-soluble inorganic compounds, and trace elements were analyzed from PM (TSP, PM10, and PM2.5) samples. The measured PM2.5 and PM10 concentrations were 5 to 10 times and 3 to 8 times higher than the 2005 WHO 24-hour standards, respectively. PCA and PMF analyses identify five sources in both cities. The sources contributing to aerosol concentrations (PM2.5 - PM10) in Bamako are motor vehicles (20-13%), solid fuel combustion (16-13%), crustal dust (24-30%), resuspended road dust (26-30%) and secondary aerosols (10-16%). During the sampling period in Bamako, dust was the most prevalent source, accounting for 63% of the total PM10 mass. In Dakar, the main identified sources were motor vehicles (28-19%), mineral dust (16-25%), industries and oil burn-ing (11-10%), sea salts (15-20%), and resuspended road particles (21-29%). The findings also indicate that anthropogenic emissions contribute significantly to the PM2.5 fraction, implying that populations are highly exposed to fine particles.

The escalating frequency and severity of global wildfires necessitate an in-depth understanding and monitoring of wildfire smoke impacts, specifically its contribution to fine particulate matter (PM2.5). We propose a data-fusion method to study wildfire contribution to PM2.5 using satellite-derived smoke plume indicators and PM2.5 monitoring data. Our study incorporates two types of monitoring data, the high-quality but sparse Air Quality System (AQS) stations and the abundant but less accurate PurpleAir (PA) sensors that are gaining popularity among citizen scientists. We propose a multi-resolution spatiotemporal model specified in the spectral domain to calibrate the PA sensors against accurate AQS measurements, and leverage the two networks to estimate wildfire contribution to PM2.5 in California in 2020 and 2021. A Bayesian approach is taken to incorporate all uncertainties and our prior intuition that the dependence between networks, as well as the accuracy of PA network, vary by frequency. We find that 1% to 3% increase in PM2.5 concentration due to wildfire smoke, and that leveraging PA sensors improves accuracy.

This article is about a framework for determining the degree of realism of any given 1 passenger ride motion discomfort measurement formula. After providing some context and reviewing 2 evidence of deficiency in currently popular ride motion discomfort measurement formulas, the article 3 outlines the research program that needs to be carried out in order to establish such a framework. 4 The research begins with gathering recordings of uncomfortable ride motion episodes encountered in 5 a chosen type of passenger transport service. It then has test subjects compare the episodes via a ride 6 motion simulator and adjust their amplitudes pair wise until they cause equal discomfort. It explains 7 how to take the pair wise amplitude adjustments and determine amplitude adjustments that bring all 8 of the motion episode recordings to a common level of discomfort so that they form a normalized set. 9 Then, the lower the scatter of the scores assigned by any given discomfort measurement formula to 10 the members of that set, the more realistic that formula will be for the chosen service.

This paper presents geometric analyses of welded frames after free relaxing and vibratory stress relief (VSR). Respected frames were tested components of a prototype packaging machine. Two types of relaxation were carried out to remove stresses introduced as a result of welding process. One of the frame was subjected to free relaxing, while the other one to accelerated vibration relaxing. Detection of the frame geometry changes was performed using a photogrammetric system. In addition, an evaluation of the geometry change was conducted for fifteen variants of steel frame support. A comparative analysis of the geometric deviations of the frames after free and vibratory stress relief confirmed the assumption that the frame after vibration stress relief better reproduces the nominal dimensions. Nevertheless, it should be emphasized that after vibratory stress relief the frame is not subject to further deformation, which is a desirable effect. In the case of free relaxing, the frame undergoes dimensional changes in a random manner. In summary, carrying out accelerated vibratory stress relief allows control of spontaneous dimensional changes in the designed frame of a packaging machine resulting from spontaneous relaxation of stresses arising from the welding process. The shortening of the relaxation process of the welded frame is also an unquestionable advantage.

This study aims to provide analyses of the levels of airborne particulate matter (PM) using a two-pronged approach that combines data from in situ Internet of Things (IoT) sensor networks with remotely sensed aerosol optical depth (AOD). Our approach involved setting up a network of custom-designed PM sensors that could be powered by the electrical grid or solar panels. These sensors were strategically placed throughout densely populated areas of North Texas to collect data on PM levels, weather conditions, and other gases from September 2021 to June 2023. The collected data was then used to create models that predict PM concentrations in different size categories, demonstrating high accuracy with correlation coefficients greater than 0.9. This highlights the importance of collecting hyperlocal data with precise geographic and temporal alignment for PM analysis. Furthermore, we expanded our analysis to a national scale by developing machine learning models that estimate hourly PM2.5 levels throughout the continental United States. These models used high-resolution data from the Geostationary Operational Environmental Satellites (GOES-16) Aerosol Optical Depth (AOD) dataset, along with meteorological data from the European Center for Medium-Range Weather Forecasting (ECMWF), AOD reanalysis, and air pollutant information from the MERRA-2 database, covering the period from January 2020 to June 2023. Our models were refined using ground truth data from our IoT sensor network, the OpenAQ network, and the National Environmental Protection Agency (EPA) network, enhancing the accuracy of our remote sensing PM estimates. The findings demonstrate that the combination of AOD data with meteorological analyses and additional data sets can effectively model PM2.5 concentrations, achieving a significant correlation coefficient of 0.849. The reconstructed PM2.5 surfaces created in this study are invaluable for monitoring pollution events and performing detailed PM2.5 analyzes. These results were further validated through real-world observations from two in situ MINTS sensors located in Joppa (South Dallas) and Austin, confirming the effectiveness of our comprehensive approach to PM analysis. The US Environmental Protection Agency (EPA) recently updated the national standard for PM2.5 to 9 μg/m3, a move aimed at significantly reducing air pollution and protecting public health by lowering the allowable concentration of harmful fine particles in the air. Using our analysis approach to reconstruct the fine-time resolution PM2.5 distribution across the entire United States for our study period, we found that the entire nation encountered PM2.5 levels that exceeded 9 μg/m3 for more than 20% of the time of our analysis period, with the eastern United States and California experiencing concentrations exceeding 9 μg/m3 for over 50% of the time, highlighting the importance of regulatory efforts to maintain annual PM2.5 concentrations below 9 μg/m3.

Chipless radio frequency identification (RFID) technology is expected to replace barcode technology due to its ability to read in non-line-of-sight (NLOS) situations, long reading range, and low cost. Currently, there is extensive research being conducted on frequency-coded (FC) co-polarized radar cross-section (RCS)-based tags, which are widely used. However, detecting co-polarized chipless RFID tags in cluttered environments is still a challenge, as confirmed by measuring two co-polarized tags in front of a perfect metal reflector (30.5cm×22.5cm). To address this challenge, a realistic mathematical model for a chipless RFID system has been developed that takes into account the characteristics of the reader and the tag, as well as reflections from cluttered objects. This model has been simulated and verified with measurement results by placing a single flat metal reflector behind two co-polarized one-bit designs: a dipole array tag and a square patch tag. The results showed that the interfering signal completely overlaps the ID of the co-polarized tag, severely limiting its detectability. To solve this issue, the proposed solution involves reading the tag in cross-polarization mode by etching a diagonal slot in the square patch tag. This proposed tag provides high immunity to the environment and can be detected in front of both dielectric and metallic objects.

The application of antimicrobials in aquaculture primarily aims to prevent and treat bacterial infections in fish. Inappropriate use of antimicrobials in fish farming may result in the emergence of zoonotic antibiotic-resistant bacteria and subsequent transmission of resistant strains to humans via food consumption. From recently, AMR emerged as a significant public health concern in the aquaculture ecosystem and fisheries. The aquatic environment serves as a potential reservoir for resistant bacteria, with aquaculture practices providing an ideal breeding ground for AMR due to the excessive use of antimicrobials to prevent and treat diseases. The mutual inter-connection of intensive fish farming systems with terrestrial environments, food processing industry and human population creates pathways for the transmission of resistant bacteria, exacerbating the problem further. One Health concept, which recognizes the interconnectedness of human, animal and environmental health, enables a holistic approach to address the challenges posed by AMR. By understanding the evolution of such approach, the future of aquaculture, being the important source of a global animal protein supply, can be safeguarded. Risk mitigation strategies for AMR should be based on One Health concept to contribute to sustainable aquaculture practices that protect human and animal health, ensure food safety and protection of environment.

Low-cost particulate matter (PM) sensors offer an excellent opportunity to improve our knowledge about this type of pollution. Their size and their cost, which support multi-node network deployment, along with their temporal resolution, enable them to report fine spatio-temporal resolution for a given area. These sensors have known issues across performance metrics. Generally, the literature focuses on the PM mass concentration reported by these sensors but some models of sensors also report particle number concentrations (PNC) segregated into different PM size bins. In this study, 8 units of each Alphasense OPC-R1, Plantower PMS5003 and Sensirion SPS30 have been exposed, under controlled conditions, to short-lived peaks of PM generated using two different combustion sources of PM, exposing the sensors to different particle size distributions to quantify and better understand the low cost sensors performance across a range of relevant environmental ranges. The PNC reported by the sensors were analysed. This study showed that there is added value in directly using the PNC reported by the sensors instead of the mass concentrations, which could aid the efforts to calibrate these sensors to a known accuracy. It demonstrated that all sensors tested here could track the fine temporal variation of PNC, that the Alphasense OPC-R1 could closely follow the variations of size distribution between the two sources of PM, and it showed that particle size distribution and composition are more impactful on the sensors measurement than relative humidity.

Candidate vaccines against African swine fever virus (ASFV) based on naturally attenuated or genetically modified viruses have the potential to generate protective immune responses, although there is no consensus on what defines a protective immune response against ASFV. Studies, espe-cially in sensible host species, focused on unravelling protective mechanisms will contribute to the development of safer and more effective vaccines. The present study provides a detailed analysis of phenotypic and functional data on cellular responses induced by intradermal immunization and subsequent boosting of domestic pigs with the naturally attenuated field strain Lv17/WB/Rie1, as well as the mechanisms underlying protection against intramuscular challenge with the virulent genotype II Armenia/07 strain. The transient mild to moderate increase of IL-8 and IL-10 in serum observed after immunization might be directly correlated with survival. Protection was also associated with a robust ASFV-specific polyfunctional memory T cell response, where CD4CD8 and CD8 T cells were identified as the main cellular sources of virus-specific IFNγ and TNFα. In parallel to cytokine response, these T-cell subsets also showed specific cytotoxic activity as evidenced by the increased expression of the CD107a degranulation marker. Along with virus-specific multifunctional CD4CD8 and CD8 T responses, the increased levels of antigen experienced cytotoxic CD4 T cells observed after challenge in immunized pigs might also contribute to control virulent infection by killing mechanisms targeting infected antigen-presenting cells. Future studies should elucidate whether the memory T-cell responses evidenced in the present study persist and provide long-term protection against further ASFV infections.

In this systematic review, the PRISMA method was applied to examine publications from the last two decades that have investigated the noxious gaseous emissions from dairy barns. The aim was to analyse the outcomes from literature studies estimating the quantities of polluting gases produced in dairy barns, with specific focus on ammonia (NH₃) emissions. The review also explores proposed methods to reduce the associated effects through mitigation strategies. Estimation of NH₃ emissions is significantly influenced by the complex interactions among several factors, including animal management practices, such as controlling animal behavioral activities; manure management, like utilising practices for floor manure removal; the type of structure housing the animals, whether it is naturally or mechanically ventilated; and environmental conditions, such as the effects of temperature, wind speed, relative humidity, and ventilation rate on NH₃ release in the barn. These influential components have been considered by researchers, identifying targeted mitigation strategies. Despite growing attention to the issue, gaps in the scientific literature were identified and discussed, particularly regarding the analysis of mitigation strategies and their long-term impacts (i.e., environmental, economic and productivity-wise).

Recent advances in differential topology single out four-dimensions as being special, allowing for vast varieties of exotic smoothness (differential) structures, distinguished by their handlebody decompositions, even as the coarser algebraic topology is fixed. Should the spacetime we reside in takes up one of the more exotic choices, and there is no obvious reason why it shouldn't, apparent pathologies would inevitably plague calculus-based physical theories assuming the standard vanilla structure, due to the non-existence of a diffeomorphism and the consequent lack of a suitable portal through which to transfer the complete information regarding the exotic physical dynamics into the vanilla theories. An obvious plausible consequence of this deficiency would be the uncertainty permeating our attempted description of the microscopic world. We tentatively argue here, that a re-inspection of the key ingredients of the phenomenological particle models, from the perspective of exotica, could possibly yield interesting insights. Our short and rudimentary discussion is qualitative and speculative, because the necessary mathematical tools have only just began to be developed.

Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

(1) Background: This study, drawing from the theoretical framework of the Theory of Planned Behavior (TPB), examines the structural relationship among attitudes, subjective norms, perceived behavioral control (PBC), and behavioral intention. The study focuses on investigating how the perceived risk associated with particulate matter moderates the relationships between 'attitudes and behavioral intention,' 'subjective norms and behavioral intention,' and 'PBC and behavioral intention' within the context of individuals engaged in outdoor sports; (2) Methods: The data were collected from outdoor sports gatherings facilitated through a popular South Korean sports meetup application. Confirmatory factor analysis was employed to establish the construct validity of the measurement scale, assess factor loadings, averaged variance extracted (AVE), and construct reliability (CR). We also ensured the reliability of the measurement scale through Cronbach's α analysis. To achieve our research objectives, we utilized structural equation modeling with maximum likelihood estimation to examine the positive relationships under investigation. Additionally, we performed moderation analysis using the statistical software Jamovi.; (3) Results: The findings demonstrate the significant impacts of attitudes, subjective norms, and PBC on behavioral intention and reveal that perceived risk acts as a moderator, influencing the relationship between PBC and behavioral intention.; (4) Conclusions: Therefore, the government will need to exert substantial efforts to mitigate particulate matter levels.

The study aims to identify the fine particulate matter (PM2.5) hazard area, mitigation method, and possible sustainable development in a changing global climate. The critical environmental hazards are artificial light at night (ALAN) and air pollution with ambient PM2.5. People use nighttime outdoor environments for their needs, and the nocturnally migrating birds are attracted to urban ALAN during seasonal migration, which could increase the birds' exposure to PM2.5. A comparative study examines PM2.5 concentrations and the spatial correlation between ALAN and PM2.5 within urban versus rural areas. The author used the nighttime data of the artificial light on the Earth's surface and the PM2.5 level of concentration to estimate the extent of air pollution associated with PM2.5 in the ground-level atmosphere. The results can assist in determining the required PM2.5 control areas and designing and executing environmental conservation planning. Furthermore, the results of this study are not only beneficial to understanding accurately the regional differences of spatiotemporal PM2.5 emission dynamics and helpful for proposing alleviation policies in air pollution control and providing scientific support for regional sustainable development in changing climate. The integrated hazards of ALAN and air pollution are most significant and likely to increase within the urban and decrease within rural areas. This study was undertaken by the first author and built upon the context of the academic, scientific, and technological challenges to identify the PM2.5 concentration in urban and rural areas and the expected outcomes.

Abstract: Cancer survivors are at an increased risk for cardiovascular disease (CVD). However, the association between particulate matter (PM) and CVD risk among cancer survivors (alive >5 years since diagnosis) is unclear. We investigated the risk of CVD among 40,899 cancer survivors within the Korean National Health Insurance Service database. Exposure to PM was determined by assessing yearly average PM levels obtained from the Air Korea database from 2008 to 2011. PMs with sizes <2.5 (PM2.5), <10 (PM10), or 2.5-10 (PM2.5-10) μm in diameter were compared, with each PM level exposure further divided into quintiles. Patients were followed up from January 2012 to date of CVD event, death, or December 2017, whichever came earliest. Adjusted hazard ratios (aHRs) and 95% confidence intervals (CIs) for CVD were calculated using Cox proportional hazards regression by PM exposure levels. Compared with cancer survivors in the lowest quintile of PM2.5 exposure, those within the highest quintile had a greater risk for CVD (aHR 1.31, 95% CI 1.07-1.59). Conversely, increasing PM10 and PM2.5-10 levels were not associated with increased CVD risk (p for trend 0.078 and 0.361, respectively). Cancer survivors who reduce PM2.5 exposure may reduce their risk of developing CVD.

In the context of freshwater ecosystems, turbidity and suspended solids play crucial roles, with their levels significantly influenced by anthropogenic activities. This study focuses on assessing and monitoring these parameters in Albufera de Valencia using Sentinel-2 imagery. The primary aim is to establish reliable estimation algorithms that can contribute to effective ecosystem management. The study calibrated and validated algorithms for estimating turbidity and suspended solids. The R783×R705/R490 model proved to have the best performance for estimating turbidity and total solids in the Albufera. However, R783/R490 obtained a higher coefficient of de-termination for the organic part, while the R705 band was selected for the inorganic part. However, to achieve better estimates of turbidity and inorganic matter, more research is needed in the future. The implications of excessive suspended solids are underscored, including the depletion of dissolved oxygen, and reduced primary productivity due to limited light penetration and habitat availability. Collaboration between disciplines such as limnology, optics and water chemistry are crucial to advance water quality estimation models in lakes and lagoons such as Albufera. By integrating expertise and approaches from these diverse fields, new knowledge can be gained and the basis for more effective management and conservation strategies can be laid.

Air pollution has created a lot of problems in the developed and developing countries. To avoid or reduce these problems, constant monitoring of the air should be ensured. The conventional techniques is costly because it requires a lot of money and time consuming. Biomonitoring has been the alternative method. Moss, lichens and plants are biomonitors available to entrap air pollutants. The aim of this paper is to discuss one of the ways of monitoring air pollution – Moss bag technique. To do this, types, choice, preparation, handling of bags after preparation of moss were discussed. From the literatures consulted, it was discovered that there were differences in the techniques used by the researchers. In all, the use of mosses with emphasis on the employment of moss bag have proved to be a powerful tool in airborne particulate and toxic elements. To conclude, developing countries should focus more on this technique because it will reduce cost of air monitoring.

NiV2O6 thin films were grown on glass slides with varying thicknesses using the nebulizer spray pyrolysis. The impact of thickness on the thin films' optical, structural, morphological, and electrical characteristics was systematically investigated. The X-ray diffraction and micro-Raman analysis confirmed the formation of the triclinic NiV2O6 system. Surface morphology and roughness variations in the as-deposited NiV2O6 films were studied using scanning electron microscopy (SEM) and a profilometer. Optical properties, including optical band gap (Eg), extinction coefficient (k), absorption coefficient (α), and refractive index (n), were determined through optical reflectance and transmittance measurements. The optical energy gap of the as-deposited NiV2O6 films decreased from 2.3 eV to 1.9 eV with increased layer thickness. Furthermore, the photo-detectivity of the films demonstrated an enhancement corresponding to the prolonged spray time. The sensitivity values obtained for visible irradiation are 328, 511, and 433 for samples S1, S2, and S3, respectively. The obtained results are imputed to the specific porous microstructure.

Background: There are major air pollution monitoring gaps in sub-Saharan Africa. Developing capacity in the region to conduct air monitoring in the region can help estimate exposure to air pollution for epidemiology research. The purpose of our study is to develop a land use regression (LUR) model using low-cost air quality sensors developed by a research group in Uganda (AirQo). Methods: Using these low-cost sensors, we collected continuous measurements of fine particulate matter (PM2.5) between May 1, 2019 and February 29, 2020 at 22 monitoring sites across urban municipalities of Uganda. We compared average monthly PM2.5 concentrations from the AirQo sensors with measurements from a BAM-1020 reference monitor operated at the US Embassy in Kampala. Monthly PM2.5 concentrations were used for LUR modeling. We used eight Machine Learning (ML) algorithms and ensemble modeling; using 10-fold cross validation and root mean squared error (RMSE) to evaluate model performance. Results: Monthly PM2.5 concentration was 60.2 µg/m³ (IQR: 45.4-73.0 µg/m³; median= 57.5 µg/m³). For the ML LUR models, RMSE values ranged between 5.43 µg/m³ - 15.43 µg/m³ and explained between 28% and 92% of monthly PM2.5 variability. Generalized additive models explained the largest amount of PM2.5 variability (R²=0.92) and produced the lowest RMSE (5.43 µg/m³) in the held-out test set. The most important predictors of monthly PM2.5 concentrations included monthly precipitation, major roadway density, population density, latitude, greenness, and percentage of households using solid fuels. Conclusion: To our knowledge, ours is the first study to model the spatial distribution of urban air pollution in sub-Saharan Africa using air monitors developed from the region itself. Non-parametric ML for LUR modeling performed with high accuracy for prediction of monthly PM2.5 levels. Our analysis suggests that locally produced low-cost air quality sensors can help build capacity to conduct air pollution epidemiology research in the region.

Particulate organic carbon (POC) is a pivotal component within the marine carbon cycle, actively involved in diverse biogeochemical processes. This study focuses on Mediterranean as the research region, selecting the most influential factors from 47 potential ones influencing surface POC. Using geographic detector for factor identification, ten primary influencers were identified. Preliminarily optimized random forest (BRF), backpropagation neural network, adaptive boosting, and extreme gradient boosting were utilized to construct POC assessment models. Notably BRF exhibited superior performance in estimating the sea surface POC. Further optimization of RF using the tuneRanger R package resulted in R² of 0.868, mean squared error of 1.119 (mg/m³) ², and mean absolute error of 1.041 (mg/m³). Surface POC concentrations in the Mediterranean for May and June 2017 were estimated. Spatial distribution analysis unveiled higher concentrations in the west, lower in the east, higher in the north, lower in the south, with higher levels near the coast and lower far from the coast. Additionally, the study deliberated on the impact of human activities on surface POC in the Mediterranean. This research contributes a high-precision method for satellite retrieval of surface POC concentrations in the Mediterranean, thereby enriching the understanding of POC dynamics in the area.

Methods to handle uncertainty in economic evaluation have gained much attention in the literature and the cost-effectiveness acceptability curve (CEAC) is the most widely used method to summarize and present uncertainty associated with program costs and effects in cost-effectiveness analysis. Some researchers have emphasized the limitations of the CEAC for informing decision and policy makers as the CEAC is insensitive to radial shifts of the joint distribution of incremental costs and effects in the North-East and South-West quadrants of the cost-effective plane (CEP). Furthermore, it has been pointed out that the CEAC does not incorporate risk-aversion in valuing uncertain costs and effects. In the present article we show that the cost-effectiveness affordability curve (CEAFC) captures both dimensions of the joint distribution of incremental costs and effects on the CEP and is therefore sensitive to radial shifts of the joint distribution on the CEP. Furthermore, the CEAFC also informs about the budget impact of a new intervention as it estimates the joint probability an intervention is both affordable and cost-effective. Moreover, we show that the cost-effectiveness risk-aversion curve (CERAC) allows to incorporate risk-aversion into the analysis and can therefore be used to inform decision-makers who are risk-averse. We use data from a published cost-effectiveness model of palbociclib in addition to letrozole versus letrozole alone for the treatment of oestrogen-receptor positive, HER-2 negative, advanced breast cancer to demonstrate the differences between CEAC, CEAFC and CERAC and show how these can jointly be used to inform decision and policy makers.

Positioning based on wireless signals such as mobile communication networks has become an important means to provide high-precision location services in environments where satellite signals are blocked. In complex environments such as indoor and underground, wireless signal propagation is obstructed and non-line-of-sight (NLOS) phenomena appears due to serious occlusion and reflection. The time delay caused by NLOS effects has little impact on communication system but can significantly increase positioning errors in positioning systems. Therefore, effective suppression of NLOS errors is crucial to improving 5G positioning accuracy. To address the insufficient feature extraction of existing NLOS error suppression methods, the neglect of residual NLOS measurement errors, and poor stability of position estimation results, this paper innovatively proposes a NLOS mitigation and location estimation method for 5G positioning terminals. Simulation and experimental test results demonstrate that the proposed method outperforms the comparative methods both theoretically and practically, achieving an average positioning accuracy of 1.85 meters in complex indoor NLOS environments. The method proposed in this paper provides a new strategy for NLOS error suppression in indoor 5G positioning, which can significantly contribute to high-precision location services based on commercial 5G networks.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of &gt;1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Currently, one of the main challenges is the mitigation of the effects of climate change on the agricultural sector. Conventional agriculture, with the intensive use of herbicides and pesticides to control weeds and pests, and the improper use of mineral fertilizers, contributes to climate change by causing increased greenhouse gases and groundwater pollution. Therefore, more innovative technologies must be used to overcome these problems. One possible solution is nanotechnology, which has the potential to revolutionize the conventional agricultural system. Active nanoparticles can be used both as a direct source of micronutrients and as a delivery platform for bioactive agrochemicals to improve crop growth, yield and quality. The use of nanoparticle formulations, including nanopesticides, nanoherbicides, nano-fertilizers and nano-emulsions, has been extensively studied to improve crop health and shelf life of agricultural products. Comprehensive knowledge of the interactions between plants and nanoparticles opens up new opportunities to improve cropping practices through the enhancement of properties such as disease resistance, crop yield, and nutrient use. The main objective of this review is to analyze the main effects of climate change on conventional agricultural practices, such as the use of pesticides, herbicides and fertilizers. It also focuses on how the introduction of nanoparticles into conventional practices can improve the efficiency of chemical pest control and crop nutrition. Finally, this review examines in depth the last 10 years (2014-2024) of scientific literature regarding the use of nanoparticles in agriculture to mitigate the effects of climate change.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

Exposure to particulate matter (PM) causes considerable breathing-related health risks. We assessed the inhibitory effect of Siraitia grosvenorii extract (SGE) on airway inflammation in mice exposed to a fine dust mixture of PM10 (PM diameter &lt; 10 mm) and diesel exhaust particles (DEPs) known as PM10D. SGE attenuated neutrophil infiltration and the number of immune B and T cells in lung tissue and bronchoalveolar lavage fluid (BALF) of PM10D-exposed mice. SGE reduced the secretion of cytokines and chemokines, including interleukin (IL)-1a, tumor necrosis factor (TNF)- a, IL-17, chemokine (C-X-C motif) ligand (CXCL)-1, and macrophage inflammatory protein (MIP)-2 in BALF. Airway inflammation, accumulation of inflammatory cells, and collagen fibrosis in the lung after PM10D exposure were investigated by histopathological analysis, and SGE treatment ameliorated these symptoms. SGE decreased the mRNA expression of mucin 5AC (MUC5AC), CXCL-1, TNF-a, MIP-2, and transient receptor potential vanilloid and ankyrin 1 ion channels in the lung tissues of mice. Furthermore, SGE ameliorated mitogen-activated protein kinase (MAPK)/nuclear factor-kappa B (NF-κB) signaling activated by PM10D in mice. We conclude that SGE attenuated PM10D-induced neutrophilic airway inflammation via inhibiting MAPK/NF-κB activation. These results show that SGE may be a candidate for the treatment of inflammatory respiratory diseases.

The implementation of sentinel lymph node (SLN) biopsy is changing the scenario in the surgical treatment of early-stage cervical cancer and the oncologic safety of replacing bilateral pelvic lymphadenectomy with SLN biopsy is currently under investigation. One of the undisputed values of SLN biopsy is its diagnostic accuracy in detecting low-volume metastases (LVM) via pathologic ultrastaging. In early-stage cervical cancer, the reported incidence of LVM ranges from 4 to 20%. The prognostic impact and the role of adjuvant treatment in patients with LVM is still unclear. Some non-prespecified analyses in prospective studies showed no impact on the oncologic outcomes compared to node-negative disease. However, the heterogeneity of the studies, the differences in the disease stage and the use of adjuvant treatment, and the concomitant pelvic lymphadenectomy (PLND) make any conclusion on this topic hard. Current guidelines suggest considering micrometastasis (MIC) as a node-positive disease, while isolated tumor cells (ITC) as a node-negative disease, with a low level of evidence. This review aims to highlight the unanswered questions about the definition, identification, prognostic and therapeutic role of LVM and underline the present and future challenges we are facing. We hope this review will guide further research, giving robust evidence on LVM and their impact on clinical practice.

Increasing levels of dissolved organic matter (DOM) in watercourses in the Northern hemisphere is mainly due to reduced acid rain, climate change, and changes in agricultural practices. However, their impacts vary in time and space. To predict how DOM respond to changes in environmental pressures we need to differentiate between allochthonous and autochthonous sources, as well as identify anthropogenic DOM. In this study we distinguish between allochthonous, autochthonous, and anthropogenic sources of DOM in a diverse watercourse network using DOM characterization tools and by assessing effects of land cover on water quality. Main sources of DOM are forests discharging allochthonous humic DOM, autochthonous fulvic DOM, and runoff from urban sites and fish farms with high levels of anthropogenic DOM rich in protein like material. Specific UV absorbency (sUVa) distinguish allochthonous DOM from autochthonous and anthropogenic DOM. Anthropogenic DOM differ from autochthonous fulvic DOM by containing elevated levels of protein like material. DOM from fishponds is distinguished from autochthonous and sewage DOM by having high sUVa. DOM characteristics thus provide valuable tools for deconvoluting the various sources of DOM allowing water resource managers to predict future trends in DOM and detect anthropogenic sources of DOM.

A typical solid-state quantum sensor can be developed based on negatively charged nitrogen-vacancy (NV-) centers in diamond. The electron spin state of NV- can be controlled and read at room temperature. Through optical detection magnetic resonance (ODMR) technology, temperature measurement inside living cells can be achieved at the nanoscale. The key to ODMR technology is to apply microwave resonance to manipulate the electron spin state of NV-. Therefore, the microwave field characteristics formed near the NV- have a crucial impact on the sensitivity of ODMR measurement. This article mainly focuses on the temperature situation in cellular applications, and simulates the influence of structural parameters of double open loop resonant (DOLR) microwave antennas and broadband large-area (BLA) microwave antennas on the microwave field’s resonance frequency, quality factor Q, magnetic field strength, uniformity, etc. The parameters are optimized to have sufficient bandwidth, high signal-to-noise ratio, low power loss, and high magnetic field strength in the temperature range of 36 ℃ to 42.5 ℃. Finally, the ODMR spectra are used for effect comparison, and the signal-to-noise ratio and Q values of the ODMR spectra are compared when using different antennas. We have provided an optimization method for the design of microwave antennas and it is concluded that the DOLR microwave antenna is more suitable for living cell temperature measurement in our study.

Nowadays the relationship between planning land use and actual land use is not so clear in general. A lot of efforts have been put in the failures of regulation for the expansion of construction land. However, it still lacks an integrated approach to study the effectiveness of land use regulation in terms of different land use types. Furthermore, the existing evaluation of land use plan mainly focuses on a general level, a detailed research on the regulation effectiveness of each construction land use type is absent. Therefore, this research tries to evaluate regulation effectiveness of land use plan, which takes Cangwu country, Guangxi Province as an example. The finding by analysis is that the total area of construction land expansion was about 3494.73 ha, nearly 1.1 times of the plan quota. Moreover, the effectiveness differs greatly in various construction land use types. Town, industrial/mining sites can be well regulated through the quota of land use plan. While, the quota regulation system is not as effective for other type of construction land. Thus, we suggest to improve the regulation effectiveness of construction land through different plan instruments.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

African Swine Fever (ASF) poses a significant threat to domestic pig populations worldwide. This study investigates the histopathological alterations in confirmed ASF-positive domestic pigs, focusing on over 100 cases from 2018 to 2021. Biological material from 118 pigs, confirmed ASF-positive via PCR examination, was histopathologically examined. Tissue samples from various organs were processed, embedded, and analyzed using hematoxylin and eosin staining. Immunohistochemistry (IHC) was employed to detect the major capsid protein (p72) of the ASF virus.Histological examination revealed characteristic ASF lesions, including severe hemorrhages, lymphoid depletion, and inflammatory infiltrates. Vascular anomalies leading to hemorrhagic events were widespread. Microthromboses were prevalent in lymph nodes and kidneys. IHC detected p72 in various organs, with tonsils consistently showing the highest viral presence.This comprehensive study underscores the pivotal role of lymph nodes, spleen, and kidneys in ASF pathogenesis, highlighting prominent vascular involvement and hemorrhagic manifestations. The study establishes the efficacy of IHC in detecting ASF virus, even in autolyzed tissue samples. Tonsils emerge as a consistent epicenter of viral presence, shedding light on the intricate pathogenesis of ASFV.

This study investigates the impacts of climate change policies on businesses across various sectors, aiming to understand how these regulations affect operational, financial, and strategic aspects of business management. Utilizing a mixed-methods approach, data was collected from 500 businesses through surveys and interviews, encompassing a wide range of industries, sizes, and geographic locations. The findings reveal a complex landscape where 30% of businesses report positive impacts, primarily in the renewable energy and technology sectors, citing increased demand for green products and improvements in energy efficiency. Conversely, 45% of businesses, especially from manufacturing and agriculture, experience negative impacts, including increased operational costs and regulatory compliance challenges. Notwithstanding, a significant majority of businesses are committed to enhancing their sustainability practices, viewing climate change policies as an opportunity for innovation and long-term growth. The study highlights the nuanced effects of climate change policies, emphasizing the need for sector-specific support measures to alleviate financial and operational burdens on negatively impacted businesses. Moreover, it points to a broader shift towards sustainability within the business community, suggesting that climate policies, despite their varied impacts, are driving significant changes in business strategies towards environmental stewardship.

The relationship between pangolin-CoV and SARS-CoV-2 has been a subject of debate. Further evidence of a special relationship between the two viruses can be found by the fact that all known COVID-19 viruses have abnormally hard outer shell (low M disorder; i.e., low content of intrinsically disordered residues in the membrane (M) protein) that so far was found in CoVs associated with burrowing animals, such as rabbits and pangolins, in which transmission involves virus remaining in buried feces for a long time. While a hard outer shell is necessary for viral survival, a harder inner shell could also help. For this reason, the N disorder range of pangolin-CoVs, not bat-CoVs, more closely matches that of SARS-CoV-2 especially when Omicron is included. The low N disorder (i.e., low content of intrinsically disordered residues in the nucleocapsid (N) protein), first observed in pangolin-CoV-2017 amd later in Omicron, is associated with attenuation according to the Shell-Disorder-Model. Our experimental study revealed that pangolin-CoV-2017 and SARS-CoV-2 Omicron (XBB.1.16 subvariant) show similar attenuations with respect to viral growth and plaque formation. Subtle differences have been observed that are consistent with disorder-centric computational analysis.

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

Artificial intelligence (AI) has emerged as a powerful tool for addressing the challenges posed by climate change and their impact on public health. By leveraging its capacity to analyze and predict climatic patterns, AI offers opportunities to enhance resource management and develop effective strategies for climate change mitigation. Moreover, AI can contribute to generating sustainable solutions that address the complex and interconnected nature of climate change. For example, AI can enable the optimization of energy consumption and facilitate the integration of renewable energy sources into existing systems. It can also support the development of climate models that provide timely and accurate predictions, enabling policymakers to implement proactive measures for disaster preparedness and response. Furthermore, AI-powered disease surveillance and mitigation techniques can improve public health outcomes by identifying patterns and trends in the spread of diseases in relation to climatic factors.However, the widespread adoption of AI-based solutions is not without challenges. Ethical concerns surrounding privacy and data ownership must be addressed, as the use of AI requires access to large datasets, raising potential privacy risks. Technical constraints, such as limited computational power and the need for sophisticated algorithms, also pose obstacles to the implementation of AI in climate change mitigation strategies. Furthermore, issues related to the accessibility and affordability of AI technologies must be resolved to ensure equitable distribution and maximize its potential impact on public health.To fully harness the power of AI in addressing climate change and improving public health outcomes, it is crucial to promote innovation, multidisciplinary collaboration, and open data science. Innovation can drive the development of new AI algorithms and technologies specifically tailored to address climate change challenges. Multidisciplinary approaches that bring together experts from diverse fields, including climate science, public health, and computer science, can foster a holistic understanding of complex systems and enable the design of comprehensive solutions. Finally, open data science practices, such as sharing data and algorithms, can facilitate collaboration and accelerate progress in mitigating climate change and its public health impacts.In conclusion, AI offers promising opportunities for effectively addressing climate change and its impact on public health. However, to fully realize its potential, it is essential to tackle ethical and privacy concerns, overcome technical constraints, and ensure accessibility and affordability. By promoting innovation, multidisciplinary collaboration, and open data science, we can unlock the transformative power of AI in mitigating climate change and improving public health outcomes.

VNREDSat-1 is the first Vietnamese satellite allowing the survey of environmental parameters such as vegetation and water coverages, or surface water quality at medium spatial resolution (from 2.5 to 10 meters depending on the considered channel). The NAOMI sensor on board VNREDSat-1 has the required spectral bands to assess the suspended particulate matter concentration, SPM. Because recent studies have shown that the remote sensing reflectance, Rrs(), at the blue (450 – 520 nm), green (530 – 600 nm), and red (620 – 690 nm) spectral bands can be assessed from NAOMI with a good accuracy, the present study is dedicated to the development and validation of an algorithm (hereafter referred to as V1SPM) to assess SPM from Rrs() over inland and coastal waters of Vietnam. For that purpose, an in situ data set of hyper-spectral Rrs() and SPM (from 0.47 to 240.14 g.m-3) measurements collected at 205 coastal and inland stations has been gathered. Among the different approaches, including 4 historical algorithms, the polynomial algorithms involving the red-to-green reflectance ratio presents the best performance on the validation data set (MAPD of 18,7%). Compared to the use of a single spectral band, the band ratio allows to reduce the scatter around the polynomial fit as well as the impact of imperfect atmospheric corrections. Due to the lack of matchup data points with VNREDSat-1, the full VNREDSat-1 processing chain (RED-NIR and V1SPM) aiming at estimate SPM from the top-of-atmosphere signal has been applied to the Landsat-8/OLI match-up data points with relatively low to moderate SPM concentration (3.33-15.25 g.m-3) showing a MAPD of 15,8%. An illustration of the use of this VNREDSat-1 processing chain during a flooding event occurring in Vietnam is provided.

Many studies utilize sensors to measure foot plantar pressure and analyze gait patterns, often focusing on assessing weight-bearing symmetry or asymmetry compared to control groups. However, a critical question arises: does the selection of the control group significantly impact study outcomes? Does chronic low back pain affect foot plantar pressure measurements? This experimental study involved 23 participants, including healthy individuals and those without foot disorders but with chronic low back pain. Dynamic foot pressure measurements were conducted using the Ortopiezometr, and data were analyzed using the "Steps" program. Participants were divided into two groups: Group 1 comprised completely healthy individuals, while Group 2 consisted of individuals without foot problems but with moderate chronic low back pain. The findings highlight a prevalence of energy release in the forefoot sensors compared to the hindfoot for both the right and left legs in most cases. Even among healthy volunteers, achieving perfect symmetry in the maximum values on the sensors for the right and left feet was a challenge. Results showed no statistically significant differences in energy released on specific sensors or duration of gait phases between the groups. Essentially, this suggests that foot pressure patterns are comparable between healthy individuals and those with low back pain. The use of sensor-equipped inserts for pedobarographic examinations indicates that, in cases of degenerative changes in the lumbar and sacral spine without accompanying acute pain, gait patterns resemble those of the healthy population.

African swine fever (ASF) is one of the major threats to pig production, and real-time PCR (qPCR) protocols are integral part of ASF laboratory diagnosis. With the pandemic spread of ASF, commercial kits have risen on the market. In Germany, the kits have to go through an approval process and thus, general validation can be assumed. However, they were never compared to each other. In this study, 12 commercial PCR kits were compared to an OIE recommended method. Samples representing different matrices, genome loads, and genotypes were included in a panel that was tested under diagnostic conditions. The comparison included user-friendliness, internal controls, and the time required. All qPCRs were able to detect ASFV genome in different matrices across all genotypes and disease courses. With one exception, there were no significant differences when comparing the overall mean. The overall specificity was 100 % [95 % CI 87.66 - 100], and the sensitivity was between 95 % and 100 % [95 % CI 91.11 - 100]. As can be expected, variability concerned samples with low genome load. Concluding, all tests were fit for purpose. The test system can therefore be chosen based on compatibility and prioritization of the internal control system.

Autosomal dominant polycystic kidney disease (ADPKD) is an inherited disorder characterized by renal tubular cystic dilatations. The cysts can develop anywhere along the nephron and over time the cystic dilatation lead to kidney enlargement. On the other hand, the cysts begin to reduce the number of functional nephrons as a consequence of cystic expansion that further contributes to the decline in renal function over the years. The pressure exerted by the dilated cysts lead to compensatory mechanisms that further contribute to the decline in renal function. These structural changes are responsible of glomerular hyperfiltration states, albuminuria, proteinuria, and haematuria. However, the presentation of ADPKD varies in children from a completely asymptomatic child with incidental ultrasound detection of cysts to a rapidly progressive disease. There have been reports of early onset of ADPKD in children younger than 2 years that showed a more rapid decline in renal function. ADPKD is caused by mutation in PKD1 and PKD2 genes. Today, the PKD1 gene mutation seems to account for up to 85% of the cases worldwide, and it is associated with worse renal outcomes. Individuals with PKD2 gene mutation seem to present a milder form of the disease, with a more delayed onset of end stage kidney disease. The cardinal sign of ADPKD is the presence of renal cysts during renal ultrasound. The current guidelines provide the clinicians the recommendations for genetic testing in children with a positive family history. Given that the vast majority of children with ADPKD present with normal or supra normal kidney function we explored the glomerular filtration rates dynamics and the renal ultrasound adjusted percentiles. 14 out of 16 patients had kidney percentile over 90%. The gene mutations were equally distributed among our cohort. In addition, we compared the modified Schwartz formula to the quadratic equation after adjusting the serum creatinine measurements. It seems that even though children with ADPKD have enlarged kidneys, the renal function is more likely normal or near normal when the quadratic estimation of glomerular filtration rate is used (qGFR tended to be lower, 111.95 ± 12.43 ml/min/1.73m2 compared to Schwartz eGFR 126.28 ± 33.07ml/min/1.73m2, p=0.14). Also, when the quadratic equation was employed, not even a patient reached the glomerular hyperfiltration thresholds. The quadratic formula showed that glomerular filtration rates are linear or slightly decreasing after 1-year of follow-up (Quadratic ΔeGFR=0.32±5.78ml/min/1.73m2) as opposed to Schwartz formula that can falsely classify children in a hyperfiltration state ΔeGFR=7.51±19.46ml/min/1.73m2), p=0.019.

As climate changes, our daily life has been much influenced by abnormal meteorological phenomena such as heavy rainfall, heat wave, heavy snowfall, and fine dust. Atmospheric air quality is worsening day by day and indoor air quality is also affected by interconnected daily activities throughout the inside and outside of buildings and houses. Nowadays, pollutants from various sources are emitted, transformed by sunlight, vapor, and ozone and transported into the city from country to country. Due to these reasons, there have been high demands to monitor the transportation of particulate matters and improve air quality. Monitoring of pollutants and identification of type and its concentration enables us to track and control its generation and consequently find out the solution. However, monitoring of pollutants, especially, particulate matter generation and its transportation is still not fully operated in atmospheric air due to its open nature and meteorological factors. Even though indoor air is relatively easy to monitor and control than outdoor in the aspect of specific volume and contaminant source, but it still needs to consider the meteorological parameters because indoor air is not fully separated from the outdoor air flow and contaminants transportation. In this study, optical approach using spectral sensor was attempted to reveal the feasibility of wavelength and chromaticity values of reflected light from specific particles. From the analysis of reflected light of various particulate matters according to different liquid additives, parameter studies were performed to investigate which experimental conditions can contribute to the enhanced selective sensing of particulate matters. Five different particulate matters such as household dust, soil, talc powder, gypsum powder and yellow pine tree pollen were utilized and observed to elucidate the relationship between property of particulate matter and detected light spectrum. Applicable approaches to assist current particle matter sensors and improve the selective sensing were suggested.

The integration of spray drying and agglomeration offers significant advantages, such us continuous production with lower energy consumption. However, it is a knife-edge process with a narrow operating window and limited degrees of freedom that decide between successful agglomeration and fluidized bed blockage due to excessive moisture. In this contribution, factors influencing the spray-through agglomeration process of skim milk powder as a model system were investigated via a design of experiments. Three in-line monitoring methods were applied and tested to observe the most important parameters in the agglomeration process: product moisture and particle size distribution. Regarding the moisture content, a capacitive moisture sensor was calibrated with linear regression and a near-infrared sensor with partial least squares regression. Near-infrared spectroscopy was found to be the suitable method for determining moisture content, while the capacitive moisture sensor mainly provides information on the bulk density, the filling level or fluidization state in the fluidized bed. Additionally, particle size distribution data was extracted from the spectral data using in-line data of a spatial filter velocimetry probe in the fluidized bed. This opens the potential to monitor both parameters in real-time with a single non-invasive sensor.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

African swine fever virus (ASFV), a highly contagious pathogen characterized by a complex structure and a variety of immunosuppression proteins, causes hemorrhagic, acute, and aggressive infectious disease that severely injure the pork product and industry. However, there is no effective vaccine or treatment. The main reasons are not only the complex mechanisms that lead to immunosuppression, but also the unknown functions of various proteins. This review summarizes the interaction between ASFV and host immune system, along with the involvement of virulence related genes and proteins, as well as the corresponding molecular mechanism of immunosuppression of ASFV, encompassing pathways such as cGAS-STING, NF-κB, JAK/STAT, apoptosis, and other modulation. The aim is to summarize the dynamic process during the ASFV infection and entry into host cell, provide a rational insight into development of vaccine and a better clear knowledge of how ASFV impacts host.

The refractive index of seawater is one of the essential parameters in ocean observation, so it is necessary to achieve high-precision seawater refractive index measurements. A seawater refractive index measurement system based on position-sensitive detectors is an effective means to achieve high-precision measurement of seawater refractive index. However, in the actual seawater refractive index measurement process, the impact of the measurement error caused by the jitter signal obtained from the measurement on the measurement results cannot be ignored. In this paper, we theoretically analyse the causes of the long jitter signals during seawater refractive index measurement and quantify the influencing factors. Through the analysis, it can be seen that the angle between the two windows in the refractive index measurement area of seawater causes a great error on the measurement results, so the angle between the two windows should be controlled within 2.06° in order to effectively reduce the measurement error. At the same time, the factors affecting the measurement accuracy of the position-sensitive detector are analysed, and the factors leading to the reduction of the measurement accuracy of the position-sensitive detector are mainly the background light, the size of the photosensitive surface, and the change of the temperature of the working environment. For the above factors, we add a narrow-band filter with a bandwidth of 0.9nm in front of the photosensitive surface of the position-sensitive detector during the construction of the measurement system, so as to filter out stray light other than the signal light source. On the premise of ensuring the measuring range of the refractive index of seawater, a position-sensitive detector with a photosensitive surface size of 4 mm×4 mm was selected. In order to reduce the temperature variation of the working environment of the position-sensitive detector, the measurement system was partitioned. In order to validate the testing error range of the optimised test system, standard seawater samples under the same conditions were measured. It can be seen that the jitter signal of the measurement system has been reduced from 0.0022mm before the optimisation to 0.0011mm after the optimisation, and the deviation of the refractive index has been reduced by 1.09×10−8RIU. The experimental results show that the refractive index of seawater has been effectively reduced by adjusting the optical path and the structure of the seawater refractive index measurement system.