A high step-up DC-to-DC converter that integrates an isolated transformer and a switched-clamp capacitor is presented in this study. The voltage stress of the main power switch should be clamped to 1/4 V by using the turn ratio and switched-clamp capacitor of an isolated transformer to achieve a high voltage gain. In addition, a passive clamp circuit is employed reduce voltage stress on the main power switch. The energy of the leakage inductor can be recycled by the clamp capacitor because of the passive clamp circuit, thereby improving the power converter efficiency. The converter consists of one isolated transformer, one main switch, three capacitors, and four diodes. Operating principle and steady-state analyses are also discussed. Finally, a 24-V-input voltage to 200-V-output voltage and a 150 W output power prototype converter are fabricated in the laboratory. The maximum efficiency of the converter is 95.1 at 60 W.

The radiation stability of polymer test objects fabricated by direct laser writing is studied. The two groups of 6 cubes (50×50×50 μm3) were printed on a common silicon substrate. 6 cubes were irradiated with X-rays in the synchrotron radiation beam (12 keV, 1010 photons/mm2/s), the other 6 kept non-irradiated for the reference. In each group, the fabrication parameters (laser power and slicing step) were uniformly varied from cube to cube. Each irradiated cube was exposed with the dose of 1013 X-ray photons. The calibration of this dose in the radiological units (Gy) was carried out using the tissue-equivalent thermoluminescent detectors (TLD-800). The corresponding exposition dose was estimated as 30 kGy for each cube. The radiation effects were evaluated by Raman spectroscopy and by morphological changes observed with the raster electron microscope. The primary radiation effect appears in the essential increase of the polymerization degree with consuming carbon-carbon double bonds in favor of the polymer cross-linking. Only one cube of 6 has changed the size and shape due to this effect, while the others retained the initial shape. Morphological changes are connected with the improper fabrication parameters (laser power and slicing step). Properly fabricated objects withstand the X-rays of the synchrotron radiation beam.

Phase imaging of biochemical samples has been demonstrated for the first time at the Infrared Microspectroscopy (IRM) beamline of the Australian Synchrotron using the usually discarded Near-IR (NIR) region of the synchrotron-IR beam. The synchrotron-IR beam at the Australian Synchrotron IRM beamline has a unique fork shaped intensity distribution as a result of the gold coated extraction mirror shape, which includes a central slit for rejection of the intense X-ray beam. The resulting beam configuration makes any imaging task challenging. For intensity imaging, the fork shaped beam is usually tightly focused to a point on the sample plane followed by a pixel-by-pixel scanning approach to record the image. In this study, a pinhole was aligned with one of the lobes of the fork shaped beam and the Airy diffraction pattern was used to illuminate biochemical samples. The diffracted light from the samples was captured using a NIR sensitive lensless camera. A rapid phase-retrieval algorithm was applied to the recorded intensity distributions to reconstruct the phase information corresponding to different planes. The preliminary results are promising to develop multimodal imaging capabilities at the IRM beamline of the Australian Synchrotron.

This work presents the results regarding the synthesis of tungsten nanoparticles (W NPs) by magnetron sputtering combined with gas aggregation (MSGA) when H2 mixed with Ar is used as working gas, the amount of H2 being increased up to 82%. The results show that up to 40% H2 in discharge the synthesis rate increases over 60 times, rapidly decreasing for over 50% H2 in discharge. The W dust is still produced in H2 dominated discharge (82%), the deposition rate being small but not negligible (20 mg/hour). The obtained WNPs are isolated, with the diameter decreasing from 50 nm to 15 nm when the amount of H2 in discharge is smaller than 41%. Over this value, the particles tend to agglomerate, forming structures similar to film-like deposits. Also, the diameter of the deposited spots on substrates is dependent on the H2 content in discharge. This allows the efficient coating of substrates with dimensions up to 26 mm by translating them in front of the MSGA cluster source exit aperture. Supplementary, for 41% H2 in discharge, the influence of synthetic air leaks (0-5%) in discharge was investigated. The deposition rate decreases rapidly (ceasing for around 4% air in discharge) and the obtained nanoparticles tend to agglomerate (at 2% air content, the dust deposit has the aspect of a near continuous film). Chemical composition investigations show a pronounced tendency of oxidation, nitridation and oxynitride formation in the presence of air leaks.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

The aim of this work was to test polyamines as potential natural substrates of the Acinetobacter baumannii chlorhexidine efflux protein AceI using near-UV synchrotron radiation circular dichroism (SRCD) spectroscopy. The Gram-negative bacterium A. Baumannii is a leading cause of hospital-acquired infections and an important foodborne pathogen. A. Baumannii strains are becoming increasingly resistant to antimicrobial agents, including the synthetic antiseptic chlorhexidine. AceI was the founding member of the recently recognised PACE family of bacterial multidrug efflux proteins. Using the plasmid construct pTTQ18-aceI(His₆) containing the A. Baumannii aceI gene directly upstream from a His₆-tag coding sequence, expression of AceI(His₆) was amplified in E. coli BL21(DE3) cells. Near-UV (250-340 nm) SRCD measurements were performed on detergent-solubilised and purified AceI(His₆) at 20 °C. Sample and SRCD experimental conditions were identified that detected binding of the triamine spermidine to AceI(His₆). In a titration with spermidine (0-10 mM) this binding was saturable and fitting of the curve for the change in signal intensity produced an apparent binding affinity (K_D) of 3.97 +/- 0.45 mM. These SRCD results were the first experimental evidence obtained for polyamines as natural substrates of PACE proteins.

Diffusion magnetic resonance imaging (dMRI) is an imaging technique that provides information on the microstructural organization of biological tissue. dMRI allows for non-invasive visualization and quantitative assessment of white matter architecture in the brain by characterizing restrictions on the random motion of water molecules. Ultra-high field MRI scanners, such as those operating at 7 Tesla (7T) or higher, can boost signal-to-noise ratio (SNR) to improve dMRI compared with what is attainable at conventional field strengths such as 3T or 1.5T. However, at 7T wavelength effects cause lower transmit magnetic field efficiency in the human brain, mainly in the posterior fossa region, manifesting as signal dropouts in this region. Recently, we reported a simple approach of using a wireless radiofrequency (RF) surface array to improve transmit efficiency and signal sensitivity at 7T. Here we demonstrate the feasibility and effectiveness of using this RF enhancer for in-vivo dMRI at 7T. The use of the RF enhancer can effectively recover signal dropouts in the regions with intrinsically lower SNR such as cerebellum, leading to a better depiction of principal fiber orientations and enhanced visualization of extended tracts to the brainstem and pons enabling more comprehensive delineation of the full white matter architecture.

We investigate solutions of the classical Mathieu-Hill (MH) equation which describes the dynamics of trapped ions, based on the Floquet theory and the analytical model introduced in \cite{Blu89}. We show the equations of motion are equivalent to those of the harmonic oscillator (HO) and demonstrate methods to determine the solutions of the MH equation. The regions of stability and instability for the MH equation in case of a trapped particle are also discussed. What is more, we address both the damped HO and parametric oscillator (PO) for an ion confined in a Paul trap. The paper is a follow-up of a recently published paper in Photonics, 11 (6) 551.

Extremely low-frequency electromagnetic fields (ELF-EMF) are ubiquitous in industrial-11 ized environments due to the continuous use of electrical devices. Our previous studies demon-12 strated ELF-EMF affects muscle cells by modulating oxidative stress and enhancing myo-genesis. 13 This pilot study investigated these effects on skeletal muscles of sedentary adult mice, assessing 14 physiological responses to ELF-EMF exposure and potential modulation by antioxidant supplemen-15 tation. Male C57BL/6 mice were exposed to ELF-EMF (0.1 or 1.0 mT) 1 hour/day up to 5 weeks, and 16 fed a standard diet without or with N-acetyl-cysteine (NAC). Results showed transient increases in 17 muscle strength (after 2-weeks’ exposure at 1.0 mT), potentially linked to muscle fiber recruitment 18 and activation, revealed by higher PAX7 and MyH expression levels. After ELF-EMF exposure, ox-19 idative status assessment revealed transient increases in expression levels of SOD1 and catalase en-20 zymes, in total antioxidant capacity and in protein carbonyl levels, marker of oxidative damage. 21 These effects were partially reduced by NAC. In conclusion, ELF-EMF exposure affects skeletal 22 muscle physiology and NAC supplementation partially mitigates these effects, highlighting the 23 complex interactions between ELF-EMF and antioxidant pathways in vivo. Further investigations 24 on ELF-EMF as a therapeutic modality for muscle health are necessary.

Embryo stage of oxidation of an epi Ge(001)-2×1 by atomic oxygen and molecular O₂ is studied via synchrotron radiation photoemission. The topmost surface buckled with the up- and down-dimer atoms and the first subsurface layer behave distinctly from the bulk by exhibiting surface core-level shifts in the Ge 3d core-level spectrum. The O₂ molecules become dissociated upon reaching the epi Ge(001)-2×1 surface. One of the O atom removes off the up-dimer atom, and the other bonds with the underneath Ge atom in the subsurface layer. Atomic oxygen adsorbed on the epi Ge(001)-2×1 preferentially in between the up-dimer atoms and the underneath subsurface atoms without affecting the down-dimer atoms. The electronic environment of the O-affiliated Ge up-dimer atoms becomes similar to that of the down-dimer atoms. Both exhibit an enrichment in charge, where the subsurface of the Ge layer is maintained in a charge-deficient state. The dipole moment originally generated in the buckled reconstruction no longer exists, thereby resulting in a decrease in the ionization potential. The down-dimer Ge atoms and the back-bonded subsurface atoms remain inert to atomic O and molecular O₂, a possible cause of low reliability in Ge-related metal-oxide-semiconductor (MOS) devices.

The stability properties of the Hill equation are discussed, and especially those of the Mathieu equation that characterize ion motion in electrodynamic traps. The solutions of the Mathieu equation for a trapped ion are characterized by using the Floquet theory and Hill's Method solution, which yields an infinite system of linear and homogeneous equations whose coefficients are recursively determined. Stability is discussed for parameters $a$ and $q$ that are real. Characteristic curves are introduced naturally by the Sturm-Liouville problem for the well known even and odd Mathieu equations $ce_m(z,q)$ and $se_m(z,q)$. We illustrate the stability diagram for a combined (Paul and Penning) trap and represent the frontiers of the stability domains for axial and radial motion. In case of a Paul trap the stable solution corresponds to a superposition of harmonic motions. The problem of evaluating the maximum amplitudes of stable oscillations for the ideal conditions (taken into consideration) is also approached. Anharmonic corrections are discussed within the frame of the perturbation theory, while the frontiers of the modified stability domains are determined as a function of the chosen perturbation parameter. The results apply to 2D and 3D ion traps used for different applications in quantum engineering, among which optical clocks, quantum logic and quantum metrology, but not restricted only to these.

Here, we present a general framework for computing the infrared anharmonic vibrational spectra of polyatomic molecules using the Born-Oppenheimer molecular dynamics (BOMD) with the software PyRAMD. To account for the nuclear quantum effects, we suggest using the simplified Wigner sampling (SWS) approach [\textit{Phys. Chem. Chem. Phys.}, 2023, \textbf{25}, 18406-18423] simultaneously coupled with the Andersen and Berendsen thermostats. We propose a new criterion for selecting the parameter of the SWS based on the molecules' harmonic vibrational frequencies and usage of the large-time-step blue shift correction, allowing for a decrease in computational expenses. For the Fourier transform of the dipole moment autocorrelation function, we propose to use the regularized least-squares analysis, which allows us to obtain higher frequency resolution than the direct application of fast Fourier transform. Finally, we suggest the usage of the pre-parameterized scaling factors for the IR spectra from BOMD, also providing the scaling factors for the spectra at the BLYP-D3(BJ)/6-31G, PBE-D3(BJ)/6-31G, and PBEh-3c levels of theory.

Halloysite and kaolinite are dioctahedral TO phyllosilicates that drive the interest of scientists for formulating environmental friendly materials, and consequently in the field of ceramics. The main scope of this study was the understanding of the texture evolution upon the dehydroxylation reaction and the influence of the presence of halloysite. In situ synchrotron (002) and (111) poles figures were recorded on the DiffAbs beamline at SOLEIL Synchrotron, from room temperature to 1000°C, on kaolinite and/or halloysite-rich samples shaped by tape casting. Commercial kaolins and halloysite provided by Imerys company were used. The samples were labeled KRG100, KCS100, H100, KRG50H50 and KRG59H50 in relation with the wt. % of kaolin (KRG, KCS) or halloysite (H) clays. In samples KCS100 and KRG100, a strong texture was observed until in situ annealing at 700°C, with respect to the c-axis of kaolinite. One the contrary, the texture with respect to the c-axis of halloysite for the sample H100 was weak whatever the temperature was. Moreover, this weak texture disappeared before the complete dehydroxylation of halloysite. This is due to the opening of some halloysite tubes. When considering the samples KRG50H50 and KCS50H50, a significant texture was observed with the c-axis preferentially oriented perpendicular to the sample surface . The presence of kaolinite platelets predominated onto the alignment of halloysites tubes. Furthermore, it was noted that the halloysite influenced the (002) diffracted intensity into the temperature range 20 °C and 400 °C. Above 400°C, the behavior obtained for the (002) reflection in samples KRG50H50 and KCS50H50 was similar to the behavior noticed for pure kaolins KRG100 and KCS100 respectively. The dehydroxylation temperature range appeared to be relevant with combined effect of kaolinite and halloysite transformations arising from KRG100 or KCS100 and H100 samples. Therefore, the onset point of dehydroxylation is 550 °C ± 25 °C for KRG100, KCS100 KRG50H50 and KCS50H50. For the pure halloysite H100 sample, the dehydroxylation starts at lower temperature 475°C. It was also noted that during the dehydroxylation of kaolinite, the characteristic portion of ring related to the diffracted intensity of the (111) reflection located at χ = 45 ° tended to disappear above 550 °C and led to the formation of a new transitory phase with a (111) reflection with perpendicular alignment to the c-axis. Indeed, an epitaxial relationship with the (111) kaolinite reflection could be assumed. Further X-ray scattering experiments allowed highlighting the effective offset temperature of the dehydroxylation, which was identified as close to 720 °C. The metakaolinite obtained undergone structural transformation to another transitory phase at 1000°C.

Synchrotron radiation computed tomography (SRCT) allows more accurate calcified plaque and coronary stenosis assessment as a result of its superior spatial resolution, however, typical micro-computed tomography (micro-CT) systems have even higher resolution. The purpose of this study was to compare performance of high-resolution micro-CT with SRCT in the assessment of calcified plaques and a previously published dataset of coronary stenosis assessment. This experimental study involved micro-CT scanning of three-dimensional printed coronary artery models with calcification in situ used in our previously published SRCT study on coronary stenosis assessment. Measurements of coronary stenosis utilizing both modalities were compared using a paired sample t-test. The degrees of stenosis measured on all but one micro-CT dataset were statistically significantly lower than the corresponding SRCT measurements reported in our previous paper (p<0.0005-0.05). This indicates that the superior spatial resolution of micro-CT was able to further reduce over-estimation of stenosis caused by extensive calcification of coronary arteries and hence false positive results. This study shows that high-resolution micro-CT outperforms SRCT in both calcified plaque and coronary stenosis assessment. This finding will become clinically important for cardiovascular event prediction and enable reclassification of individuals with low and intermediate risk into appropriate risk categories when the technical challenges of micro-CT in clinical practice such as the small field of view and demanding on image processing power are addressed.

Seeing atomic configuration of single organic nanoparticles at sub-Å spatial resolution by transmission electron microscopy has been so far prevented by the high sensitivity of soft matter to radiation damage. The difficulty is related to the need to irradiate the particle with a total dose of few electrons/Å2, not compatible with the electron beam density necessary to search the low-contrast nanoparticle, to control its drift, to finely adjust the electro-optical conditions and particle orientation, and to finally acquire an effective atomic resolution image. On the other hand, the capability to study individual pristine nanoparticles, such as proteins, active pharmaceutical ingredients, and polymers, with peculiar sensitivity to the variation of the local structure, defects, and strain, would provide advancements in many fields, including materials science, medicine, biology, and pharmacology. Here we report direct sub-ångström resolution imaging at room temperature of pristine unstained crystalline polymer-based nanoparticles. This result is obtained by combining low-dose in-line electron holography and phase-contrast imaging on state-of-the-art equipment, providing an effective tool for the quantitative sub-angstrom imaging of soft matter.

The review scrutinizes the currently performed research on the new methods for enhancing bituminous binder performance through radiation and radical grafting of polymer modifers of bitumen. It investigates innovative methods, including using waste polymers as modifiers, and applying radiation for polymer grafting, to overcome challenges like high costs, low aging resistance and storage stability issues, of which separation of phases polymer/bitumen is the most significant obstacle. These advanced modification techniques promise sustainability through the decrease of the carbon footprint of transportation systems by improving the properties and durability of binders. Additionally, the review discusses the parameters and mechanistic aspects from a scientific perspective, shedding light on the underlying processes that contribute to the improved performance of modified bituminous binders.

Simple summary This reassessment of the findings from our Phase I/II study seeks to evaluate the effectiveness of SBRT for treating local intermediate-high risk prostate cancer in the absence of androgen-deprivation therapy due to patient’s refusal, with a median follow-up of 6.5 years. Our primary focus is on analysing the treated areas compared to recurrence patterns in the seven patients who experienced local relapse. Additionally, we provide updated data on late toxicities of grade 2 or higher, both genitourinary and gastrointestinal. Abstract Objectives: We investigated spatial patterns between primary and recurrent tumor sites and assessed long-term toxicity after dose escalation stereotactic body radiation therapy (SBRT) to the dominant intraprostatic nodule (DIN). Materials and methods: In 33 patients with intermediate-high risk prostate cancer (PCa), doses up to 50 Gy were administered to the DIN. Recurrence sites were determined and compared to the original tumor development sites through multiparametric MRI and 68Ga-labelled prostate-specific membrane antigen (PSMA) positron emission tomography/computed tomography (68Ga-PSMA-PET/CT) images. Overlap rates, categorized as 75% or higher for full overlap, and 25-74% for partial overlap, were assessed. Long-term toxicity is reported. Results: All patients completed treatment, with only one receiving concomitant androgen deprivation therapy (ADT). Recurrences were diagnosed after a median of 33 months (range: 17-76 months), affecting 13 out of 33 patients (39.4%). Intraprostatic recurrences occurred in 7 patients (21%), with ≥ 75% overlap in two, a partial overlap in another two, and no overlap in the remaining three patient. Notably, 5 patients with intra-prostatic recurrences had synchronous bone and/or lymph node metastases, while six patients had isolated bone or lymph node metastasis without intraprostatic recurrences. Extended follow-up revealed grade 2 or higher late GU and GI toxicity in 18% (n=6) and 6% (n=2) of the patients. Conclusions: Among patients with intermediate-high risk PCa undergoing focal dose-escalated SBRT without ADT, DIN recurrences were infrequent. When present, these recurrences were typically located at the original site or adjacent to the initial tumor. Conversely, relapses beyond the DIN and in extra-prostatic (metastatic) sites were prevalent, underscoring the significance of systemic ADT in managing this patient population. Advances in knowledge: focal dose escalated prostate SBRT prevented recurrences in the dominant nodule, however extra-prostatic recurrence sites were frequent.

Patients with metastatic epidural spinal cord compression (MESCC) and favorable survival prognoses may benefit from radiation doses exceeding 10 x 3.0 Gy. In a multi-center phase 2 trial, patients receiving 15 x 2.633 Gy (41.6 Gy10) or 18 x 2.333 Gy (43.2 Gy10) were evaluated for local progression-free survival (LPFS), motor/sensory functions, ambulatory status, pain, distress, toxicity, and overall survival (OS). They were compared (propensity score adjusted Cox regression) to a historical control group (N=266) receiving 10 x 3.0 Gy (32.5 Gy10). In the phase 2-cohort, 50 (of 62 planned) patients were evaluable for LPFS. Twelve-month rates of LPFS and OS were 96.8% and 69.9%, respectively. Motor and sensory functions improved in 56% and 57.1% of patients, and 94.0% were ambulatory following radiotherapy. Pain and distress decreased in 84.4% and 78.0% of patients. Ten and two patients experienced grade 2 and 3 toxicities, respectively. Phase 2 patients showed significantly better LPFS than the control group (p = 0.039) and a trend for improved motor function (p = 0.057). Ambulatory and OS rates were not significantly different. Radiotherapy with 15 x 2.633 Gy or 18 x 2.333 Gy was well tolerated and appeared superior to 10 x 3.0 Gy.

The theory of water transport in trees, according to which the main driving force of water movement is the suction created by the evaporation of water by the meniscus (the curved surface of the capillary liquid column) on the evaporating elements, supported from below by root pressure, is flawed. The capillary effect in nature is around one meter. In the case of open-air gaps, the leaf cannot suck in the water against gravity because, in this case, the plant would not be sucking in water, but air through the open-air gap. If not, how do trees transport water? When evaporation occurs, there is no suction towards the canopy, but pressure is due to a reduction in the cross-section of the water pipe caused by heat loss through evaporation. At night, when evaporation stops, a thermal equilibration process is triggered, which restores the original cross-section of the pipe. This generates suction and draws water from the soil. As the hydrostatic pressure in the pipe is high for tall trees, the pipe is cut off. To prove my theory, I have given several examples. Water transport is not based on physical mechanical laws alone. There may be complex physiological, biochemical, and biophysical processes behind the operation of the pipe system.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

Background: Studies have tried to identify predictors of functional markers of keratoconus progression, whereas structural outcomes of collagen cross-linking have not been properly investigated. Objective: find and set up a combination of diagnostic modalities and measurements to reliably reflect CXL efficiency. Material and methods: We retrospectively reviewed the medical histories of 107 KC patients (131 eyes) who underwent CXL in a medical center from January 2018 to December 2022. The dataset included preoperative examinations and follow-up results, which provided a total of 796 observations. The cases of other corneal diseases, repeated CXL, pregnancy, and observations without follow-up examinations were excluded. Results: The study findings revealed a significant drop in the central and corneal thickness during 14.01±9.98 months of observations. Linear and polynomial equations suggested different trends in pachymetry change after CXL. The linear model showed corneal thinning, and according to the polynomials, pachymetry findings return to baseline values two years after CXL. Conclusion: The most reliable prognosis of postoperative corneal thickness is achieved with the models trained on keratometry readings and topography indices. BAD indices are also reliable predictors of the corneal thickness after CXL. A combination of the aforementioned structural parameters and their derivatives can reliably predict CXL efficiency.

Ionizing radiation exposure can cause damage to diverse tissues and organs, with the hematopoietic system being the most sensitive. However, limited information is available regarding the radiosensitivity of various hematopoietic cell populations in the bone marrow due to the high heterogeneity of the hematopoietic system. In this study, we observed that granulocyte-macrophage progenitors, hematopoietic stem/progenitor cells and B cells within the bone marrow showed the highest sensitivity, exhibiting a rapid decrease in cell numbers following irradiation. Nonetheless, neutrophils, natural killer (NK) cells, T cells, and dendritic cells demonstrated a certain degree of radioresistance, with neutrophils exhibiting the most pronounced resistance. By employing single-cell transcriptome sequencing, we investigated the early responsive genes in various cell types following irradiation, revealing that distinct gene expression profiles emerged between radiosensitive and radioresistant cells. In B cells, radiation exposure led to a specific upregulation of genes associated with mitochondrial respiratory chain complexes, suggesting a connection between these complexes and cell radiosensitivity. In neutrophils, radiation exposure resulted in fewer gene alterations, indicating their potential for distinct mechanisms in radiation resistance. Collectively, this study provides insights into the molecular mechanism for the heterogeneity of radiosensitivity among the various bone marrow hematopoietic cell populations.

Drowsiness is a main factor for various costly defects, even fatal accidents in areas such as construction, transportation, industry and medicine, due to the lack of monitoring vigilance in the mentioned areas. The implementation of a drowsiness detection system can greatly help to reduce the defects and accident rates by alerting individuals when they enter a drowsy state. This research proposes an Electroencephalography (EEG) based approach for detecting drowsiness. EEG signals are passed through a preprocessing chain composed of artifact removal and segmentation to ensure accurate detection followed by different feature extraction methods to extract the different features related to drowsiness. This work explores the use of various machine learning algorithms such as Support Vector Machine (SVM) the K Nearest Neighbor (KNN) the Naive Bayes (NB) the Decision Tree (DT) and the Multilayer Perceptron (MLP) to analyze EEG signals sourced from the DROZY database, carefully labeled into two distinct states of alertness (awake, and drowsy). Segmentation into 10-second intervals ensures precise detection, while a relevant feature selection layer enhances accuracy and generalizability. The proposed approach achieves high accuracy rates of 99.84% and 96.4% for intra (subject by subject) and inter (cross-subject) modes, respectively. SVM emerges as the most effective model for drowsiness detection in the intra mode, while MLP demonstrates superior accuracy in the inter mode. This research offers a promising avenue for implementing proactive drowsiness detection systems to enhance occupational safety across various industries.

This study aimed to demonstrate the potential role of Dual Energy CT in assessing Bone Mineral Density (BMD) in postmenopausal women. A retrospective study was conducted on 51 postmenopausal female patients who underwent DXA and DECT examinations for other clinical reasons. DECT images were acquired with spectral imaging using a 256-slice system. These images were processed and visualized using an HAP(fat) map. Statistical analysis was performed using the Bland-Altman method to assess agreement between DXA and DECT HAP(fat) measurements. Mean BMD, vertebral and femoral T-scores were obtained. For vertebral analysis, the Bland-Altman plot showed an inverse correlation (R2: -0.042; RMSE: 0.690) between T-scores and DECT HAP(fat) values for measurements from L1 to L4, while a good linear correlation (R2: 0.341; RMSE: 0.589) it was found for measurements at the femoral neck. In conclusion, we demonstrated the enhanced accuracy of BMD calculation through DECT, finding a statistically significant correlation only at the femoral neck where BMD results do not seem to be influenced by the overlap of the measurements on cortical and trabecular bone. This outcome could be beneficial in the future by reducing radiation exposure for patients already undergoing follow-up for chronic conditions.

: Image guided superficial radiation therapy (IGSRT) combines superficial radiation therapy (SRT) with full dermal visualization (FDV) via high resolution dermal ultrasound (HRDUS) for the treatment of non-melanoma skin cancer (NMSC). The gold standard for IGSRT delivery includes a comprehensive cancer care model with support for the dermatologists by a multidisciplinary team. When delivered in this model, IGSRT can achieve cure rates of 99% for treatment of NMSC. This paper focuses on the benefits of IGSRT during therapy. Medical records from 7 dermatology clinics of 883 patients with 1,507 cases of NMSC treated with IGSRT be-tween 2017 and 2018 were retrospectively reviewed. 92% of the NMSC lesions showed daily depth fluctuations, 60.32% of lesions did not require changes during therapy, and nearly 40% of lesions required at least one compensatory change during therapy. 83% of NMSC lesions were labeled high-risk based on the 2024 NCCN guidelines. Increasing and decreasing tumor depth measurements during IGSRT inform dermatologists when adaptive changes in energy (kV), TDF and dose will result in more efficacy and less toxicity, respectively.

Abstract: We have filled a 24 mm diameter glass sphere with a transparent polymer-gel that is radio-fluorogenic, i.e. it becomes (permanently) fluorescent when irradiated, with an intensity proportional to the local dose deposited. The gel consists of >99.9% tertiary-butyl acrylate (TBA) pre-polymerized to ~15% conversion, and ~100 ppm maleimido-pyrene (MPy). Its dimensions and physical properties are close to those of the vitreous body of the human eye. We have irradiated the gel with a 3 mm diameter, 200 kVp X-ray beam with a dose rate of ~1 Gy/min. A 3D (video) view of the beam within the gel has been constructed from tomographic images obtained by scanning the sample through a thin sheet of UV light. To minimize optical artifacts, the cell was immersed in a square tank containing a refractive-index-matching medium. The 20%-80% penumbra of the beam was determined to be ~0.4 mm. The research was a preparatory investigation of the possibility of using the method to monitor the millimetre diameter proton pencil beams used in ocular radiotherapy.

Objective: This study aimed to assess the impact of artificial intelligence (AI)-driven noise reduction algorithms on metal artifacts and image quality parameters in cone-beam computed tomography (CBCT) images of the oral cavity. Materials and Methods: This retrospective study included 70 patients, 61 of whom were analyzed after excluding those with severe motion artifacts. CBCT scans, performed using a Hyperion X9 PRO 13 × 10 CBCT machine, included images with dental implants, amalgam fillings, orthodontic appliances, root canal fillings, and crowns. Images were processed with ClariCT. AI deep learning model (DLM) for noise reduction. Objective image quality was assessed using metrics such as the differentiation between voxel values (ΔVVs), the artifact index (AIx), and the contrast-to-noise ratio (CNR). Subjective assessments were performed by two experienced readers, who rated overall image quality and artifact intensity on predefined scales. Results: Compared with native images, DLM reconstructions significantly reduced the AIx and increased the CNR (p<0.001), indicating improved image clarity and artifact reduction. Subjective assessments also favored DLM images, with higher ratings for overall image quality and lower artifact intensity (p<0.001). However, the ΔVV values were similar between the native and DLM images, indicating that while the DLM reduced noise, it maintained the overall density distribution. Orthodontic appliances produced the most pronounced artifacts, while implants generated the least. Conclusion: AI-based noise reduction using ClariCT. AI significantly enhances CBCT image quality by reducing noise and metal artifacts, thereby improving diagnostic accuracy and treatment planning. Further research with larger, multicenter cohorts is recommended to validate these findings.

The morphological and compositional complexities of keratinized components make feathers ingenious skin appendages adapted to diverse ecological needs. Frizzling feathers, characterized by their distinct curling phenotypes, offer a unique model to explore the intricate morphogenesis in developing a keratin-based bioarchitecture over a wide range of morphospace. Here, we investigated the heterogeneous allocation of α- and β-keratins in flight feather shafts of homozygous and heterozygous frizzle chickens by analyzing the medulla-cortex integrations using quantitative morphology characterizations across scales. Our results reveal intriguing construction of frizzling feather shaft through modified medulla development, leading to a perturbed balance of the internal biomechanics and, therefore, introducing the inherent natural frizzling compared to those from wild-type chickens. We elucidate how the localized developmental suppression of the α-keratin in the medulla interferes with the growth of the hierarchical keratin organization by changing the internal stress in the frizzling feather shaft. This research not only offers insights into the morphogenetic origin of the inherent bending of frizzling feathers but also facilitates our in-depth understanding of the developmental strategies toward the diverse integuments adapted for ecological needs.

Medulloblastoma (MB) is one of the most common malignant pediatric brain tumors. Current therapy results in poor prognosis for high-risk SHH/p53-mutated MB, emphasizing the importance of more effective therapeutic strategies. Here, we investigated potential radiosensitizing effects of checkpoint kinase inhibitors (Chk-i) prexasertib (Chk1/2) and SAR-020106 (Chk1) in human SHH/p53-mutated MB in vitro and in vivo. UW228 and DAOY cells were treated with Chk-i and irradiation (RT). Metabolic activity, proliferation, and apoptosis was determined at d3, long-term clonogenicity at d14. DNA damage was assessed after 1, 24, and 72 h. Patient-derived SHH/p53-mutated, luciferase-transfected MB cells were implanted orthotopically into NSG mice (d0). Fractionated therapy (daily, d7-11) was applied. Body weight (BW) was documented daily, tumor growth weekly, and proliferation at d42. In vitro, Chk-i exhibited dose-dependent reduction of metabolic activity, proliferation, and clonogenicity, and enhancement of apoptosis. Combination with RT showed additive antitumor effects and enhanced residual DNA damage. In vivo, tumor growth was delayed by Chk-i alone. Low-dose prexasertib enhanced RT-induced tumor growth inhibition (37-fold) and reduced proliferating cells, high-dose prexasertib and SAR-020106 showed opposite effects (n=3, n.s.). BW assessments revealed that the treatment was well tolerated. Our data indicate a benefit of Chk-i in combination with RT in SHH/p53-mutated MB. However, high-dose Chk-i may compromise the RT effect, possibly by its anti-proliferative activity. Furthermore, we demonstrate for the first time the antitumor activity of the Chk1-specific inhibitor SAR-020106 in the murine brain.

Mesenteric ischemia diagnosis is challenging with an overall mortality in up to 50% of cases despite advances in treatment. The main problem that affects the outcome is the delayed diagnosis because of non-specific clinical presentation. Multi Detector CT Angiography (MDCTA) is the first line investigation for the suspected diagnosis of vascular abdominal pathologies and is the diagnostic test of choice in suspected mesenteric bowel ischemia. MDCTA can accurately detect the presence of arterial and venous thrombosis, determine the extension and the gastrointestinal tract involved, and provide detailed information determining the subtype and the stage progression of the diseases helping clinicians and surgeons for the proper management. CT can differentiate forms that are still susceptible to pharmacological or interventional treatment (NOM= non-operative management) from advanced disease with transmural necrosis in which a surgical approach is required. Knowledge of CT imaging patterns and corresponding vascular pathways is mandatory in Emergency settings to reach a prompt and accurate diagnosis. The aims of this paper are 1. to provide technical information about the optimal CTA protocol; 2. To empathize the CTA arterial and venous supply to gastrointestinal tract and relative ischemic pattern; 3. To describe vascular, bowel and extraintestinal CT findings for the diagnosis of acute mesenteric ischemia.

The nuclear magnetic resonance (NMR) metabolomic analysis was applied to investigate the differences within nineteen Sicilian Nocellara del Belice mono varietal Extra Virgin Olive Oils (EVOO), grown in two zones different for altitude and soil composition. Several classes of endogenous olive oil metabolites were quantified through a nuclear magnetic resonance (NMR) three-experiment protocol coupled with a yet developed data-processing called MARA-NMR. This method, taking around one-hour experimental time per sample, faces the possible quantification of different class of compounds at different concentration’s range which would require at least three alternative traditional methods. NMR results were compared with the data of traditional analytical methods to quantify free fatty acidity (FFA), fatty acid methyl esters (FAMEs), and total phenol content. The presented NMR methodology is compared with traditional analytical practices and its consistency is also tested through slightly different data treatment. Despite the rich literature about the NMR of EVOOs, the paper points out that there are still several advances potentially improving this general analysis and overcoming the other cumbersome and multi-devices analytical strategies. Monovarietal EVOO’s composition is mainly affected by pedoclimatic conditions in turn relaying upon the nutritional properties, quality, and authenticity. Data collection, analysis and statistical processing are discussed touching the important issues related to the climate changes in Sicily and to the specific influence of pedoclimatic conditions.

Introduction: Lymph-nodal prostate cancer oligometastases are differently treated according to their site: pelvic are locoregional lymph-nodes, instead para-aortic lymph-nodes are considered as distant metastases. Aim of the study was a comparison between para-aortic and pelvic oligometastases treated with stereotactic body radiation therapy (SBRT). Material/methods: This is a retrospective analysis. De-novo metastatic or extra-nodal disease were excluded. Univariate and multivariate analyses were performed; pattern of recurrence was evaluated too. A propensity score matching (PSM) was applied to create comparable cohorts. Primary end-point was the progression-free survival (PFS). Secondary end-points were biochemical relapse-free survival (BRFS), ADT-free survival (ADTFS), polymetastases-free survival (PMFS), local progression-free survival (LPFS) and pattern of relapse. Results: 240 lymph-nodal oligometastases in 164 patients (127 pelvic and 37 para-aortic) were treated. Median PFS was 20 and 11 months in pelvic and para-aortic patients respectively (p=0.042). The difference was not confirmed at the multivariate analysis (p=0.06). Median BRFS was 16 and 9 months respectively in pelvic and para-aortic group (p=0.07). No statistically significant differences for ADTFS or PMFS were detected. The cumulative 5-years LPFS was 90.5%. At PSM no statistically significant differences for all the study end-points were detected. Conclusions: Patients affected by para-aortic disease might have PFS comparable to pelvic disease; local control is high in both cohorts. Our results support the use of SBRT also to para-aortic metastases.

Background and Objectives To compare navigator-gated three-dimensional T1-weighted gradient-echo sequences (NG-3D T1W-GRE) with standard breath-hold T1W-GRE (BH T1W-GRE) for the detection of HCC nodules in patients with chronic viral hepatitis which undergo at magnetic resonance imaging (MRI) using gadoxetic acid. Methods and materials We evaluated 58 patients with hepatic nodules at least 1 cm in diameter detected by ultrasound who underwent liver MRI including NG-3D T1W-GRE sequences and breath hold T1-weighted gradient-echo sequences with different flip angles(FA) at 10-25-40° after contrast administration of gadoxetic acid at magnetic scanner operating at1.5 Tesla. Image quality and relative hepatic and nodular enhancement were evaluated by three blinded reviewers. Results In these patients, image quality of NG-3D T1W-GRE was assessed significantly better than quality of BHT1W- GRE (P < 0.005) and relative enhancement was significantly higher than that of BH- T1W-GRE ( P

Background and Objectives: High job strain is worsening the outcome in coronary artery disease, CAD. Severe dissatisfaction on workplace, imbalance between high demands , and low rewards, are affecting the quality of life, and diminishing the duration of life, especially in CAD patients. Our study included two samples : CAD patients (experimental group), and without CAD patients, but with traditional risk factors (control group). The main objective of the study was the role played by high sensitivity C reactive protein, hs CRP, and microalbuminuria, as mediators of job strain and CAD relationship. Secondary objectives were the following: identification of the most vulnerable patients( with significant job strain) and intervention towards this category, for cardiovascular events prevention (primary or secondary). Materials and Methods: The utilized methods were the following : clinical exam; electrocardiogram; echocardiogram; non contrast enhanced computed chest tomography; laboratory findings ( lipid profile, glycemia, hs CRP, microalbuminuria); type D scale, DS 14; depression questionnaire, PHQ-9; and satisfaction with work scale, SWWS. Results: The highest values for hs CRP and microalbuminuria were noticed in patients with the lowest Likert score, for both samples CAD, and without CAD patients. The highest job strain was noticed in females. More than half of CAD patients ,with low Likert scores, revealed myocardial infarction. Conclusions: Microalbuminuria and hs CRP were statistical significant in the study as intercessors, in job strain and CAD relationship. The most vulnerable patients for vascular events were females, in both groups : CAD and “CAD waiting desk”. In CAD sample, the vascular vulnerability was also increased by high job strain.

Artificial Intelligence (AI) and Machine Learning (ML) approaches that could learn from large data sources have been identified as useful tools to support clinicians in their decisional process; AI and ML implementations have had a rapid acceleration during the recent COVID-19 pandemic. However, many ML classifiers are “black box” to the final user, since their underlying reasoning process is often obscure. Additionally, the performance of such models suffer from poor generalization ability in presence of dataset shift. Here, we present a comparison between an explainable-by-design (“white box”) model (Bayesian Network (BN)) versus a black-box model (Random Forest), both studied with the aim to support clinicians of Policlinico San Matteo University Hospital in Pavia (Italy) during the triage of COVID-19 patients. Our aim is to evaluate whether the BN predictive performances are comparable with those of a widely used but less explainable ML model such as Random Forest and to test the generalization ability of the ML models across different waves of the pandemic.

The MAPK signaling pathway with BRAF mutations has been shown to drive the pathogenesis of 40-60% of melanomas. Inhibitors of this pathway's BRAF and MEK components are currently used to treat these malignancies. However, responses to these treatments are not always successful. Therefore, identifying noninvasive biomarkers to predict treatment responses is essential for personalized medicine of melanoma patients. Using noninvasive 1H magnetic resonance spectroscopy (1H MRS), we previously showed that BRAF inhibition reduces lactate and alanine tumor levels at early stages of effective therapy and could be construed as metabolic imaging biomarkers for drug response. The present work aimed to demonstrate if these metabolic changes and those assessed by 31P MRS are also found in preclinical human melanoma models treated with MEK inhibitors. Apart from 1H and 31P MRS, additional supporting in vitro biochemical analyses are described. Our results indicate significant early metabolic correlations with response levels to MEK inhibition in the melanoma models and are consistent with our previous study of BRAF inhibition. Given these results, our study supports the potential clinical utility of noninvasive MRS to objectively image metabolic biomarkers for early predicting melanoma response to MEK inhibition.

Many of the fundamental molecules of life share extraordinary pigment-like optical properties in the long-wavelength UV-C spectral region. These include strong photon absorption and rapid (sub pico-second) dissipation of the induced electronic excitation energy into heat through peaked conical intersections. These properties have been attributed to a ``natural selection'' of molecules resistant to the dangerous UV-C light incident on Earth's surface during the Archean. In contrast, the ``thermodynamic dissipation theory for the origin of life'' argues that, far from being detrimental, UV-C light was, in fact, the thermodynamic potential driving the dissipative structuring of life at its origin. The optical properties were thus the thermodynamic ``design goals'' of microscopic dissipative structuring of organic UV-C pigments, today known as the ``fundamental molecules of life'', from common precursors under this light. This ``UV-C Pigment World'' evolved towards greater solar photon dissipation through more complex dissipative structuring pathways, eventually producing visible pigments to dissipate less energetic, but higher intensity, visible photons, up to wavelengths of the ``red-edge''. The propagation and dispersal of organic pigments, catalyzed by animals, and their coupling with abiotic dissipative processes, such as the water cycle, culminated in the apex photon dissipative structure, today's biosphere.

The physiological process of iodine uptake in the thyroid is used for 131I treatment of thyroid diseases. Children are more sensitive to radiation compared to adults and may react differently to 131I exposure. The aims of this study were to evaluate the effects on thyroid protein expression in young and adult rats one year after 131I injection, and identify potential biomarkers related to 131I exposure, absorbed dose, and age. Twelve Sprague Dawley Rats (young and adults) were i.v. injected with 50 kBq or 500 kBq 131I and were killed twelve months later. Twelve untreated rats were used as age-matched controls. Quantitative proteomics, statistical analysis and evaluation of biological effects was performed. The effects of irradiation were most prominent in young rats. Protein biomarker candidates were proposed related to age, absorbed dose, thyroid function and cancer and a panel was proposed for 131I exposure. In conclusion, the proteome of rat thyroid was differentially regulated twelve months after low-intermediate dose exposure to 131I in both young and adult rats. Several biomarker candidates are proposed for 131I exposure, age, and many of them are known to be related to thyroid function or thyroid cancer. Further research on human samples are needed for validation.

Quantum correlations, especially time correlations, are crucial in ghost imaging in order to significantly reduce the background noise on the one hand while increasing the imaging resolution. Moreover, the time correlations serve as a critical reference, distinguishing between signal and noise, which in turn enable clear visualization of biological samples. Quantum imaging also addresses the challenge involved in imaging delicate biological structures with minimal photon exposure and sample damage. Here we explore the recent progress in quantum correlation-based imaging, notably its impact on secure imaging and remote sensing protocols as well as on biological imaging. We also exploit the quantum characteristics of heralded single-photon sources (HSPS) combined with decoy-state methods for secure imaging. This method uses Quantum Key Distribution (QKD) principles to reduce measurement uncertainties and protect data integrity. It is highly effective in low-photon-number regimes for producing high-quality, noise-reduced images. The versatility of decoy-state methods with WCSs (WCS) is also discussed, highlighting their suitability for scenarios requiring higher photon numbers. We emphasize the dual advantages of these techniques: improving image quality through noise reduction and enhancing data security with quantum encryption, suggesting significant potential for quantum imaging in various applications, from delicate biological imaging to secure quantum communication.

In this paper, we present a comprehensive 4D study of the early stage of plastic deformation in a polycrystalline binary AlLi alloy. The entire microstructure is mapped with X-ray diffraction contrast tomography and a set of bulk grains is further studied via X-ray topotomography during mechanical loading. The observed contrast is analyzed with respect to the slip system activation and the evolution of the orientation spread is measured as a function of applied strain. The experimental observations are augmented by the mechanical response predicted by crystal plasticity finite element simulations to analyze the onset of plasticity in details. Simulation results show a general agreement of the individual slip system activation during loading and that comparison with experiments at the length scale of the grains may be used to fine tune the constitutive model parameters.

One of the tools for optimal crop production is regular monitoring and assessment of crops. During the growing season of fruit trees, the bloom period has increased photosynthetic rates that correlate with the fruiting process. This paper presents the development of an image processing algorithm to detect peach blossoms on trees. Images of an experimental peach orchard were acquired from the Parma Research and Extension Center of the University of Idaho using an off-the-shelf unmanned aerial system (UAS), equipped with a multispectral camera (Near-infrared, Green, Blue). The orchard has different stone fruit varieties and different plant training system. Individual tree images (high-resolution) and arrays of trees images (low-resolution) were acquired to evaluate the detection capability. The image processing algorithm was based on different vegetation indices. Initial results showed that the image processing algorithm could detect peach blossoms and demonstrate good potential as a monitoring tool for orchard management.

The study of localized surface plasmons (LSPs) in nanoscale structures is an essential step towards identifying optimal plasmonic modes that can facilitate robust optomechanical coupling and deepen our understanding of light-matter interactions at the nanoscale. This paper investigates numerically, using the finite element method, LSPs modes in a design comprising two coupled nano-ridges deposited on a gold layer, with an interposing polymer spacer layer. Such a structure, usually referred to as particles-on-mirror, shows exquisite optical properties at the nanoscale. We first examine the LSPs modes of a single nano-ridge through the analysis of its scattering cross-section in the visible and infrared range. To enhance the plasmonic response, a thin polymer layer is placed at the middle of the ridge, which introduces additional LSPs modes confined within the former. Then, we extend the analysis to the dimer configuration, which exhibits more complex and enhanced plasmonic behavior compared to a single nano-ridge. In particular, the dimer configuration yields LSPs resonances with a quality factor enhancement of approximately threefold relative to single nano-ridge. Furthermore, the presence of the polymer layer within the ridges significantly improves plasmon field localization and quality factor. These findings underscore the potential of nano-ridge-based structures in advancing optomechanical coupling and plasmon-phonon interaction studies, offering valuable insights for the development of high-performance acousto-plasmonic devices. In particular, the proposed device could help significantly improve the design of nano-acousto-optic modulators operating in the visible or in the near infrared, that require enhanced light-photon coupling rate.

Background: In high-risk breast cancer patients with skin infiltration the administration of a uniform dose to superficial tissues is fundamental in order to reduce local skin relapse. A personalized bolus may prevent the potential standard bolus’ inadequate dose distribution due to air gaps between the bolus and the skin. In this pilot study, we introduced in clinical practice the use of a personalized 3D printed bolus filled with ultrasound transmission gel. Methods: Seven patients undergoing radiotherapy after mastectomy were selected. 3D printed bolus dosimetric assessment was performed with MOSFET dosimeters on an anthropomorphic phantom and subsequently on three selected cases with increasing bolus shape irregularity. Acute/late toxicity and local control was assessed. Results: Overall, for the clinical cases the percentage median difference between measured and calculated doses was -2.7% (-7.0%÷4.9%). Median follow-up was 21 months. After two years, one patient showed G2 pain, one patient manifested G1 telangiectasia, one patient showed G1 hyperpigmentation, and two patients had no relevant toxicity. Conclusions: Personalized 3D-printed bolus filled with ultrasound gel may easily reproduce the standard bolus’ consistency providing an accurate coverage of the target area with tolerable acute/late toxicity grades. This is a pilot study and further investigations are needed.

Recombinant α1-microglobulin (A1M) is proposed as protector during 177Lu-octreotate treatment of neuroendocrine tumors, which is currently limited by bone marrow and renal toxicity. Co-administration of 177Lu-octreotate and A1M could result in a more effective treatment by protecting healthy tissue, but, the radioprotecting action of A1M is not fully understood. The aim of this study was to examine the proteomic response of kidneys and bone marrow early after 177Lu-octreotate and/or A1M administration. Mice were injected with 177Lu-octreotate and/or A1M, while control mice received saline or A1M vehicle solution. Bone marrow, kidney medulla, and kidney cortex were sampled after 24 hours or 7 days. Differential protein expression was analyzed with tandem mass spectrometry. Dosimetric estimation was based on 177Lu activity in kidney. PHLDA3 was the most prominent radiation responsive protein in kidney tissue. In general, no statistically significant difference in expression of radiation-related proteins was observed between the irradiated groups. Most canonical pathways were identified in bone marrow from the 177Lu-octreotate+A1M group. Altogether, tissue-dependent proteomic response followed exposure to 177Lu-octreotate alone or together with A1M. Combining 177Lu-octreotate with A1M did not inhibit the radiation induced protein expression early after exposure, and late effects should be further studied.

Hypoxia is a hallmark of solid tumors, including hepatocellular carcinoma (HCC). Hypoxia has proved to be involved in multiple tumor biological processes and associated with malignant progression and resistance to therapy. Transarterial chemoembolization (TACE) is a well-established locoregional therapy for patients with unresectable HCC. However, TACE-induced hypoxia regulates tumor angiogenesis, energy metabolism, epithelial-mesenchymal transition (EMT), and immune processes through hypoxia-inducible factor 1 (HIF-1), which may have adverse effects on the therapeutic efficacy of TACE. Hypoxia has emerged as a promising target for combination with TACE in treatment of HCC. This review summarizes impact of hypoxia on HCC tumor biology, adverse effects of TACE-induced hypoxia on its therapeutic efficacy, highlighting the therapeutic potential of hypoxia-targeted therapy in combination with TACE for HCC.

Introduction Atherosclerotic disease is a major contributor to heart failure, stroke, and myocardial infarction, significantly lowering the quality of life and life expectancy, with a significant burden on healthcare. Not all lesions deemed non-significant are benign, and conversely, not all significant lesions are causative of ischemia. Fractional flow reserve (FFR) provides a functional assessment of coronary lesions, while optical coherence tomography (OCT) offers detailed imaging of plaque morphology, aiding in therapeutic decision-making. The objective of this study was to evaluate the utility of OCT and FFR as adjunctive tools in the catheterization laboratory for guiding therapeutic decisions in patients with multivessel disease for non-culprit vessels. Specifically, we aimed to assess how OCT and FFR influence therapeutic decision-making in patients with multi-vessel coronary artery disease. Methods 36 patients with acute coronary syndrome (ACS) and multivessel disease were randomized 1:1 into two groups: one guided by FFR alone, and the other by a combination of FFR and OCT. For the FFR group, revascularization decisions for non culprit lesions were based solely on FFR measurements. If the FFR was >0.8, the procedure concluded, and the patient received maximal medical treatment. If the FFR was ≤0.8, a stent was placed. For the FFR + OCT group, if the FFR was >0.8, the revascularization decision was based on OCT findings. If there were no vulnerable plaques (VP), the procedure concluded, and the patient received maximal medical treatment. If OCT imaging indicated VP, then the patient underwent revascularization. If the FFR was ≤0.8, the patient underwent revascularization regardless of OCT findings. Results OCT imaging altered the therapeutic decision in 11 cases where FFR measurements were above 0.8, but the lesions were characterized as VP. Analyzing the total change in the decision to stent, 4 cases in the FFR group and 15 cases in the FFR and OCT group (4 based on FFR and 11 on OCT) revealed a statistically significant difference (p = 0.0006; Relative Risk = 0.2556; 95% CI: 0.1013 to 0.5603). When analyzing the change in the total decision both to stent and not to stent, we observed a statistically significant difference, with Group 1 having 7 cases and Group 2 having 15 cases (p = 0.0153; Relative Risk = 0.4050; 95% CI: 0.2004 to 0.7698) Conclusion Based on the findings of this study, OCT significantly increases the percentage of stenting procedures by identifying vulnerable lesions. The use of intracoronary imaging facilitates the timely identification and treatment of these vulnerable lesions. This underscores the crucial role of OCT in enhancing the precision of coronary interventions by ensuring timely intervention for vulnerable lesions, thereby potentially improving patient outcomes Acknowledgment funding „This work was supported by the University of Medicine, Pharmacy, Science and Technology ,, George Emil Palade’’ of Targu Mures Research Grant number 510/14/17.01.2022”

Ship detection from synthetic aperture radar (SAR) imagery is crucial for various fields in real-world applications. Numerous deep learning-based detectors have been investigated for SAR ship detection, which require a substantial amount of labeled data for training. However, SAR data annotation is time-consuming and demands specialized expertise, resulting in that deep learning-based SAR ship detectors struggle due to a lack of annotations. With limited labeled data, semi-supervised learning is a popular approach for boosting detection performance by excavating valuable information from unlabeled data. In this paper, a semi-supervised SAR ship detection network is proposed, termed as Multi-Teacher Dempster-Shafer Evidence Fusion Net-work (MTDSEFN). The MTDSEFN is an enhanced framework based on the basic teacher-student skeleton frame, comprising two branches: the Teacher Group (TG) and the Agency Teacher (AT). The TG utilizes multiple teachers to generate pseudo-labels for different augmentation versions of unlabeled samples, which are then refined to obtain high-quality pseudo-labels by using Dempster-Shafer (D-S) fusion. The AT not only serves to deliver weights of its own teacher to the TG at the end of each epoch, but also updates its own weights after each iteration, enabling the model to effectively learn rich information from unlabeled data. The combination of TG and AT guarantees both reliable pseudo-label generation and learning comprehensive diversity information from numerous unlabeled samples. Extensive experiments were performed on two public SAR ship datasets, and the results demonstrated the effectiveness and superiority of the proposed approach.

Although ovarian cystic teratoma is the most common ovarian tumor, complications are quite rare. However, it is important to be recognized by the radiologist in order to avoid inaccurately diagnosing them as malignant lesions. This case report describes a 61-year-old postmenopausal woman, who presented to the emergency room with abdominal pain following a minor blunt abdominal trauma. In this context, a CT scan was performed, which showed the presence of round, hypodense masses randomly distributed in the peritoneum, with coexisting ascites in moderate amount; ovarian carcinoma with peritoneal carcinomatosis was suspected. The patient was hospitalized and an MRI of the abdomen and pelvis was recommended for a more detailed lesion characterization. Following this examination, the patient was diagnosed with mature cystic ovarian teratoma complicated by rupture. Surgery was performed, and the outcome was favorable. The cases of ruptured cystic teratomas are rare, and to our knowledge, this is the first occurrence described in literature. Special attention must be paid when confronting with such a case in medical practice, since it can easily misdiagnosed as peritoneal carcinomatosis

During the high-speed flight of a vehicle in the atmosphere, surface friction with the air generates aerodynamic heating. The aerodynamic heating phenomenon can create extremely high temperatures near the surface. These high temperatures impact material properties and the structure of the aircraft, so thermal deformation measurement is essential in aerospace engineering. This paper revisits high-temperature deformation measurement using the digital image correlation (DIC) technique under high-intensity blackbody radiation with a precise speckle pattern fabrication and a heat haze reduction method. The effect of speckle pattern on the DIC measurement has been thoroughly studied at room temperature, but high-temperature measurement studies have not reported such effects so far. We found that the commonly used methods to reduce the heat haze effect could produce incorrect results. Hence, we propose a new method to mitigate heat haze effects. An infrared radiation heater was employed to make an experimental setup that could heat a specimen up to 950 ℃. First, we mitigated image saturation using a short-wavelength bandpass filter with blue light illumination, a standard procedure for high-temperature DIC deformation measurement. Second, we studied how to determine the proper size of the speckle pattern under a high-temperature environment. Third, we devised a reduction method for the heat haze effect. As proof of the effectiveness of our developed experimental method, we successfully measured the deformation of stainless steel 304 specimens from 25 ℃ to 800 ℃. The results confirmed that this method can be applied to the research and development of thermal protection systems in the aerospace field.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

This study investigated a novel radioimmunotherapy strategy for targeting tumor angiogenesis. We developed a radiopharmaceutical complex by labeling an anti-adenosine triphosphate syn-thase (ATPS) monoclonal antibody (mAb) with the radioisotope 177Lu using DOTA as a chelating agent. 177Lu-DOTA-ATPS mAb demonstrated high labeling efficiency (99.0%) and stability in se-rum. MKN-45 cancer cells exhibited the highest cellular uptake, which could be specifically blocked by unlabeled ATPS mAb. In mice, 177Lu-DOTA-ATPS mAb accumulated significantly in tumors, with a tumor uptake of 16.0 ± 1.5%ID/g on day 7. 177Lu-DOTA-ATPS mAb treatment sig-nificantly reduced the viability of MKN-45 cells in a dose-dependent manner. In a xenograft tumor model, this radioimmunotherapy strategy led to substantial tumor growth inhibition (82.8%). Furthermore, combining 177Lu-DOTA-ATPS mAb with sunitinib, an anti-angiogenic drug, en-hanced the therapeutic efficacy of sunitinib in the mouse model. Our study successfully developed 177Lu-DOTA-ATPS mAb, a radioimmunotherapy agent targeting tumor blood vessels. This ap-proach demonstrates significant promise for inhibiting tumor growth, both as a single therapy and in combination with other anti-cancer drugs.

In the contemporary world of science, continuous observation of specific fixed regions is required, awaiting the emergence of targets or phenomena within those areas to locate and identify them. Astronomy requires continuous monitoring of stars, swiftly pinpointing occurrences, such as flares, and acquiring their spectral data to aid identification. In military contexts, continuous observation of specific areas is essential for promptly locating enemy movements and obtaining target spectral data for deciphering enemy disguises. Additionally, continuous observation of experimental samples in biochemistry is mandatory to pinpoint localized changes and acquire spectral data from those areas. Hence, this paper develops a novel imaging spectrometer solution to monitor localized regions continuously. Specifically, this paper first elaborates on the developed instrument’s characteristics and optical structure, followed by optical design software simulations. The instrument has an F-number of 5, a focal length of 100mm, and a field of view covering the wavelength range from 400nm to 600nm. The optical path diagram indicates that the system’s dispersion and imaging images can be separated, meeting the system’s requirements. Besides, the Modulation Transfer Function (MTF) graph confirms that the image quality meets the requirements. Furthermore, a region-monitoring type imaging spectrometer was constructed to assess the instrument’s capability for spectral observation of fixed regions. The instrument can detect a fixed area, with the target placed within the detection area. Spectral data were successfully obtained by conducting image processing on the acquired images. The correlation coefficient between this data and reference data was as high as 0.9226, indicating the instrument’s successful measurement of the target’s spectrum. Thus, the developed instrument demonstrated that it can image the observed areas and acquire spectral data from targets within those regions.

This review is focused on the current status of quantitative MR (qMR) of skeletal muscle. The first section covers the techniques of qMR in muscle with the focus on each quantitative parameter, the corresponding imaging sequence, discussion of the relation of the measured parameter to underlying physiology/ pathophysiology, the image processing and analysis approaches, and studies on normal subjects. We cover the more established parametric mapping from T1 weighted imaging for morphometrics including image segmentation, proton density fat fraction, T2 mapping, diffusion tensor imaging to emerging qMR features such as magnetization transfer including ultralow TE imaging for macromolecular fraction, and strain mapping. The second section is a summary of current clinical applications of qMR of muscle; the intent is to demonstrate the utility qMR in different disease states of the muscle rather than a complete comprehensive survey.

This study considers an application of the first-order Grey Markov Model to foresee the values of Italian power generation in relation to the available energy sources. The model is used to fit data from the Italian energy system from 2000 to 2022. The integration of Markovian error introduces a random element to the model, which is able now to capture inherent uncertainties and misalignments between the Grey model predictions and the real data. This application provides valuable insights for strategic planning in the energy sector and future developments. The results show good accuracy of the predictions, which provides powerful information for the effective implementation of energy policies concerning the evolution of energy demand in the country. Despite advancements, Italy’s 2032 energy mix will still significantly rely on fossil fuels, emphasizing the need for sustained efforts beyond 2032 to enhance sustainability.

Neuroblastoma (NB) is a childhood cancer with heterogeneous characteristics, posing challenges to effective treatment. NBs express somatostatin receptors that facilitates the use of somatostatin analogs (SSTAs) as tumor-seeking agents for diagnosis and therapy. High-risk (HR) NBs often have gain-of-function mutations in the receptor tyrosine kinase anaplastic lymphoma kinase (ALK). Despite intensive multimodal treatment, survival rates remain below 40% for children with HR-NB. The aim of this work was to investigate the combined effect of the SSTA 177Lu-octreotide with the ALK inhibitor lorlatinib. Mice bearing human HR-NB CLB-BAR tumors were treated with lorlatinib, 177Lu-octreotide, combination of these pharmaceuticals or saline (control). Tumor volume was monitored and tumor samples were evaluated for cleaved caspase-3 and expression of 84 human genes involved in apoptosis. Combination treatment with 177Lu-octreotide and lorlatinib demonstrated synergistic antitumor effects. Increased number of cleaved caspase 3-positive cells was observed in tumors from mice treated with 177Lu-octreotide alone and in combination with lorlatinib. Modulation of Bcl-2 family gene expression was observed only in the presence of both 177Lu-octreotide and lorlatinib, with BID downregulated and HRK upregulated on days 2 and 7, respectively. The data suggests that ALK signaling pathway inhibition may contribute to radiosensitization in radionuclide therapy with 177Lu-octreotide.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

D-dimer testing in combination with clinical assessment is commonly used to diagnose suspected DVT and pulmonary embolism. However, as D-dimer levels are physiologically higher in elderly patients, this test loses clinical specificity in the setting of geriatric patients. The aim of our study was to investigate the changes in D-dimer levels with age and the specificity of the D-dimer test in the diagnosis of pulmonary embolism. 1617 elderly patients consecutively admitted to the Geriatric Emergency Care Department of the INRCA-IRCCS hospital between January 2013 and February 2014 and for whom D-dimer results were available were included. The D-dimer immunoturbidimetric assay was performed on a cs-2100i Sysmex Siemens using a conventional cut-off level of 500 µg/L. The median D-dimer level was 1200 [550-2990] µg/L FEU, and the percentage of patients with D-dimer levels below the conventional cut-off was only 22.1%. As expected, there was a significant age-related increase in D-dimer, even when sex was considered, and a significant decrease in the specificity of D-dimer assay with age. The most established use of D-dimer testing is in the diagnosis of deep vein thrombosis or pulmonary embolism. Our study confirms the need for an age-adjusted cut-off for D-dimer testing in geriatric patients.

Traditional photodynamic therapy (PDT) is often limited in its efficacy by insufficient light penetration, inefficient photosensitizer energy transfer, and inadequate target tissue oxygenation. X-ray activated PDT (XPDT), using nanoparticle (NPs) photosensitizers comprised of europium-doped yttrium oxide cores encased within silica shells (Y₂O₃:Eu@SiO₂), offers the potential of overcoming most of these limitations. Aimed at maximizing the generation of reactive oxygen species (ROS), this study reports methodologies for investigation of the effects of synthesis conditions on the characteristics of Y₂O₃:Eu@SiO₂ NP. Transmission electronic microscope (TEM) revealed that the NP core diameter was linearly, positively correlated with condensation time (R2 = 0.7357, p < 0.05) and linearly, negatively correlated with urea concentration (R2 = 0.958, p < 0.05). The addition of cetyltrimethylammonium bromide (CTAB) during core synthesis demonstrated enhanced particle dispersion. Silica coating via APTES-1 and TEOS-3 conditions resulted in Y₂O₃:Eu@SiO₂ NPs that generated the highest ROS, with 8.7-fold and 8.9-fold increase respectively in relative fluorescence intensity at 8 Gy irradiation compared to a 5.2-fold increase in PBS under the same condition. In vivo evaluation using 18F-fluorothymidine positron emission tomography (18F-FLT PET) of mouse xenografts of a human prototypical cancer (ovarian) revealed a 55% reduction in tumor proliferation of radiation-sensitive CAOV3 tumors treated with Y₂O₃:Eu@SiO₂ NPs compared to a 19% reduction in tumor proliferation of radiation-resistant SKOV3 tumors on the fourth day post-treatment. Taken together, these findings suggest Y₂O₃:Eu@SiO₂ NPs can serve as effective photosensitizers for XPDT and their performance characteristics can be optimized by selecting synthesis conditions and parameters to deliver the desirable therapeutic effects, offering novel approaches to circumventing many of the limitations of conventional PDT in the treatment of cancer.

This paper presents a wideband dual-polarized dipole antenna structure operating at 1.7-3.8 GHz (76.4%). For a traditional 4G dipole antenna which covers the band 1.71 GHz- 2.69 GHz, it’s difficult to maintain the satisfactory impedance matching and normal stable radiation patterns within the 5G sub-6 GHz band 3.3-3.8 GHz, which mainly due to the fixed antenna height is no longer a quarter-wavelength. To solve this, a connected-ring-shaped metasurface structure is proposed and deployed to operate as an artificial magnetic conductor (AMC). As a result, stable antenna radiation patterns are obtained within the whole band 1.7-3.8 GHz. For verification, this wideband dipole antenna using AMC is implemented and tested. The measured results show that the proposed antenna has an impedance bandwidth of 80.7% (1.7-4.0 GHz). It has an average measured in-band realized gain of 7.0±1.0 dBi and a stable 70∘±5∘ half power beam width (HPBW) within the 4G/5G-sub 6GHz bands 1710-2690 MHz and 3300-3800 MHz.

To ensure consumers can purchase high-quality rice, accurate identification of rice varieties is particularly important. Methods: This article conducts research based on machine learning algorithms from the perspectives of image, spectrum, and spectrogram fusion. Six types of hyperspectral image data of rice were preprocessed using convolutional smoothing (SG) and multiple scatter correction (MSC). Texture information of the images was extracted using gray-level co-occurrence matrix. Spectra, texture, and spectrogram data were fused into a new matrix. Spectral, texture, and spectrogram fusion data were used as inputs for the model, and support vector machines (SVM), logistic regression (LR), and K-nearest neighbors (KNN) classification models were constructed and compared. Results: From the classification results, the spectrogram fusion classification performance was better than classification models using only spectra or texture. Conclusion: The research results showed that the accuracy of SVM and LR classification models exceeded 90%, and the LR model performed the best, effectively classifying rice varieties.

A time-sequential working, spatially multiplexed autostereoscopic 3D display design consisting of a fast switchable RGB-color filter array is presented. The wavelength-selective filter barrier emits the light from a display over a larger active area than common autostereoscopic barrier displays. An optical modelling of wavelength-selective barriers has been used for instance to calculate the light ray distribution properties of that arrangement. To find well working display designs, automated searches by simulation and computational evaluation has been proceeded. Wavelength-selective filter barrier arrangements exhibit characteristics different from common barrier displays with similar barrier pitch and ascent. In particular, these constructions show strong angular luminance dependency under barrier inclination specified by correspondent slant angle. In time-sequential implementation it is important to avoid that quick eye or eyelid movement lead to visible color artifacts. In the millisecond regime tunable liquid crystal Fabry-Pérot color filters for the colors red, green and blue are presented. They consist of a sub-micrometer thick nematic layer sandwiched between dielectric mirrors and ITO-electrodes. These cells shall switch narrow-banding light of red, green or blue. An array for a glasses-free 3D display has to be equipped with several thousand switchable filter elements having different color apertures. The newly introduced design is usable as a multi user display as well as a single user system with user adaptive control.

Traumatic vascular injuries consist in direct or indirect damage to arteries and/or veins and accounts for 3% of all traumatic injuries. Typical consequences are hemorrhage and ischemia. Extremities vascular injuries can occur isolated or in association in major trauma with other organ injuries. They account for 1-2% of patients admitted to Emergency Department, for approximately 50% of all arterial injuries. Lower extremities are more frequently injured than the upper ones in adult population. The outcome of vascular injuries is strictly correlated to the environment and the time background. Treatment can be challenging notably in polytrauma because of the dilemma of which injury should be prioritized and treatment delay can cause disability or even death especially for limb vascular injury. Our purposes are to discuss the role of Computed Tomography Angiography (CTA) in the diagnosis of vascular trauma and its optimized protocol to achieve the definitive diagnosis, and to assess the radiological signs of vascular injuries and the possible pitfalls.

Background and Objectives: Medulloblastoma is the most common malignant brain tumor in children. In recent decades, the therapeutic landscape has undergone significant changes, with stereotactic radiosurgery (SRS) emerging as a promising treatment for recurrent cases. Our study provides a comprehensive analysis of the long-term efficacy and safety of SRS in recurrent medulloblastomas across both pediatric and adult patients at a single institution. Methods: We retrospectively reviewed the clinical and radiological records of patients who underwent CyberKnife SRS for recurrent cranial medulloblastomas at our institution between 1998 and 2023. Follow-up data were available for 15 medulloblastomas in 10 patients. The cohort comprised 8 pediatric patients (ages 3-18) and 2 adult patients (ages 19-75). Median age at the time of SRS was 13 years, median tumor volume accounted for 1.9 cc, median biologically equivalent dose (BED) was 126 Gy, and single-fraction equivalent dose (SFED) was 18 Gy. The SRS was administered at 75% of the median isodose line. Results: Following a median follow-up of 39 months (range: 6-78), 53.3% of the medulloblastomas progressed, 13.3% regressed, and 33.3% remained stable. The 3-year local tumor control (LTC) rate for all medulloblastomas was 65%, with lower rates observed in the adult cohort (50%) and higher rates in pediatric patients (67%). The 3-year overall survival (OS) rate was 70%, with significantly higher rates in pediatric patients (75%) compared to adult patients (50%). The 3-year progression-free survival (PFS) rate was 58.3%, with higher rates in pediatric patients (60%) compared to adult patients (50%). Two pediatric patients developed radiation-induced edema, while two adult patients experienced radiation necrosis at the latest follow-up, with both adult patients passing away. Conclusion: Our study provides a complex perspective on the efficacy and safety of CyberKnife SRS in treating recurrent cranial medulloblastomas across pediatric and adult populations. The rarity of adverse radiation events (ARE) underscores the safety profile of SRS, reinforcing its role in enhancing treatment outcomes. The intricacies of symptomatic outcomes, intertwined with factors such as age, tumor location, and prior surgeries, emphasize the need for personalized treatment approaches. Our findings underscore the imperative for ongoing research and the development of more refined treatment strategies for recurrent medulloblastomas. Given the observed disparities in treatment outcomes, a more meticulous tailoring of treatment approaches becomes crucial.

The growing expansion of the economy and population has resulted in an increased inclination towards the utilization of groundwater resources. Conducting a geophysical survey is a widely employed method for subsurface mapping and the detection of groundwater. A geophysical study was conducted in Nanshan township, Huarong County, located in the Hunan province of the South-Central region of China. The investigation involved the utilization of a 2D Electrical Resistivity Imaging technique employing forward and inverse pole-dipole electrode array. A total of six survey lines were established, each with an electrode distance from the nearest measuring point to exceeding 800 m. The maximum current electrode separation was utilized in this setup. The spacing between the electrical resistivity sounding points was established at regular intervals. The findings from the exploration indicate the existence of multiple faults within the surveyed region. The study additionally identified two regions of structural failure, which occurred due to the convergence of faults oriented in different directions. This convergence led to the fracturing of rocks, an increase in water content, and a decrease in resistivity. The findings from the exploration were utilized in the formulation of five verification target boreholes. The results of this study offer significant insights that can inform future investigations into groundwater exploration endeavors within the region.

Electromagnetic interference (EMI) generated by switching operations within high voltage DC (HVDC) converter stations is an issue that has been addressed by CIGRE and methods to manage EMI should be considered in the design phase using electromagnetic modeling techniques. It is shown that method of moments-based techniques that have been used in many previous studies may not be sufficient. Here, the finite-difference time-domain method is used to study the properties of single switching events using a realistic model of an HVDC converter station with special emphasis on determining the impact of the valve hall on shielding EMI. It is shown that the valve hall does not confine high frequency electromagnetic fields to the valve hall; rather it delays them from exiting through bushings in the wall. Further, it is shown that incorporating electromagnetic absorbing material into the valve hall design can significantly reduce EMI outside the converter station.

The utilization of optical antennas for active control of far-field radiation at the subwavelength scale is crucial in various scientific and technological applications. We propose a thermally tunable disk design of indium tin oxide (ITO) and aluminum gallium nitride (Al0.18Ga0.82As), enabling a switch between absorption and scattering. Furthermore, the control of far-field radiation pattern can be easily realized by combining ITO and Al0.18Ga0.82As to enhance or suppress emission. Our results demonstrate that hybrid structure can be dynamically tuned with temperature variations. In the proposed design, a frequency is achieved at the epsilon-near-zero wavelength of 1240 nm. The thermal tunability of hybrid structure introduces new multifunctional possibilities for light manipulation, thereby enhancing the potential applications of new devices in the near-infrared range.

Motor intention is a high-level brain function related to planning for movement. Although studies have shown that motor intentions can be decoded from brain signals before movement execution, it was unclear whether intentions relating to mental imagery of movement could be decoded. Here, we investigated whether differences in spatial and temporal patterns of brain activation were elicited by intentions to perform different types of motor imagery and whether the patterns could be used by a multivariate pattern classifier to detect such differential intentions. The results showed that it is possible to decode intentions before the onset of different types of motor imagery from functional MR signals obtained from fronto-parietal brain regions, such as the premotor cortex and posterior parietal cortex, while controlling for eye movements and for muscular activity of the hands. These results highlight the critical role played by the aforementioned brain regions in covert motor intentions. Moreover, they have substantial implications for rehabilitating patients with motor disabilities.

Many fields of human activity benefit from the ability to create images of obscured objects placed behind walls and to map their displacement in a noninvasive way. Usually, imaging devices like Synthetic Aperture Radars (SAR) and Ground Penetrating Radars (GPR) use expensive dedicated electronics which results in prohibitive prices. This paper presents the experimental implementation and the results obtained from an imaging system capable of performing SAR imaging and interferometric displacement mapping of targets located behind walls, as well as 3D GPR imaging using a low-cost general-purpose radar sensor. The proposed solution uses for the RF section of the system a K-band microwave radar sensor module implementing Frequency Modulated Continuous Wave operation. The low-cost sensor was originally intended for simple presence detection and ranging for domestic applications. The proposed system was tested in several scenarios and proved to operate as intended for a fraction of the cost of a commercial imaging device.

Localized protein translation occurs through trafficking of mRNAs and protein translation machineries to different compartments of the cell, leading to rapid on-site synthesis of proteins in response to signaling cues. The spatiotemporally precise nature of the local translation process necessitates continual developments of technologies reviewed herein to visualize and map biomolecular components and the translation process with better spatial and temporal resolution, and with fewer artifacts. We also discuss approaches to control local translation, which can serve as a design paradigm for subcellular genetic devices for eukaryotic synthetic biology.

The combination of immunoPET—where an antibody (Ab) is labeled with an isotope for PET imaging—and radioimmunotherapy (RIT), using the same antibody with a therapeutic isotope, offers significant advantages in cancer management. ImmunoPET allows non-invasive imaging of antigen expression, which aids in patient selection for a subsequent radioimmunotherapy. It also facilitates the assessment of tumor response to therapy, allowing for treatment adjustments if necessary. In addition, immunoPET provides critical pharmacokinetic data, including antibody biodistribution and clearance rates, which are essential for dosimetry calculations and treatment protocol optimization. There are still challenges to overcome. Identifying appropriate target antigens that are selectively expressed on cancer cells while minimally expressed on normal tissues remains a major hurdle to reduce off-target toxicity. In addition, it is critical to optimize the pharmacokinetics of radio-labeled antibodies to maximize tumor uptake and minimize normal tissue uptake, particularly in vital organs such as the liver and kidney. This approach offers the potential for targeted and personalized cancer therapy with reduced systemic toxicity by exploiting the specificity of monoclonal antibodies and the cytotoxic effects of radiation. However, further research is needed to address remaining challenges and to optimize these technologies for clinical use.

Despite great technical capabilities, the theory of non-contact temperature measurement is usually not fully applicable to the use of measuring instruments in practice. While black body calibrations are in practice well established and easy to accomplish, this calibration protocol is never fully applicable to measurements of real objects under real conditions. Currently, the best approximation to real world radiation thermometry is grey body radiation thermometry, which is supported by most measuring instruments to date. Nevertheless, the metrological requirements necessitate traceability, therefore real body radiation thermometry is required for temperature measurements of real bodies. This article documents the current state of temperature calculation algorithms for radiation-thermometers and the creation of a traceable model for radiation thermometry of real bodies that uses a digital twin model of the system of measurement to compensate for the loss of data, caused by spectral integration, which occurs when thermal radiation is absorbed on the active surface of the sensor. To solve this problem, a hybrid model with variable scalar inputs is proposed, in which the scalar input parameters are calculated to correspond to the system of measurement. The method for calculating the effective parameters is proposed and verified with the theoretical model of non-contact thermometry. The sum of effective instrumental parameters is presented for different temperatures to show that the rule of radiation thermometry of grey bodies, according to which the sum of instrumental emissivity and instrumental reflectivity equals to 1, does not hold in radiation thermometry for real bodies. Using the derived models of radiation thermometry, the uncertainty of radiation thermometry due to the uncertainty of spectral emissivity is analysed by simulated measurements along the temperature ranges of various radiation thermometers, enabling traceable non-contact temperature measurements with known measurement uncertainty under any known conditions.

Background: Painful spinal bone metastases (PSBMs) patients regularly receive palliative radiation therapy (RT) with response rates in about 2 of 3 patients. In this exploratory study, we evaluated the value of machine learning (ML) models based on radiomic, semantic and clinical features to predict complete pain response. Methods: Gross tumour volumes (GTV) and clinical target volumes (CTV) of 261 PSBMs were segmented on planning computed tomography (CT) scans. Radiomic, semantic and clinical features were collected for all patients. Random forest (RFC) and support vector machine (SVM) classifiers were compared using repeated nested cross-validation.Results: The best radiomic classifier was trained on CTV with an area under the receiver-operator curve (AUROC) of 0.62 ± 0.01 (RFC; 95% confidence interval). The semantic model achieved a comparable AUROC of 0.63 ± 0.01 (RFC), significantly below the clinical model (SVM, AUROC: 0.80 ± 0.01); and slightly lower than the spinal instability neoplastic score (SINS; LR, AUROC: 0.65 ± 0.01). A combined model did not improve performance (AUROC: 0,74 ± 0,01).Conclusions: We could demonstrate that radiomic and semantic analyses of planning CTs allowed for limited prediction of therapy response to palliative RT. ML predictions based on established clinical parameters achieved the best results.

Camouflage is a natural or artificially process to prevent an object from being detected while camouflage breaking is a countering process for the identification of the concealed object. We report that a perfectly camouflaged object in a two-dimensional scene can be retrieved and detected with stereo-vision assisted three-dimensional (3D) imaging perceived with stereopsis. The analysis is based on binocular energy model applied to general 3D settings. We show that a perfectly concealed object with random noise background can be retrieved with vision’s stereoacuity to resolve the hidden structures. The theoretical analysis is further tested and demonstrated with distant natural images taken by a drone-camera, processed with a computer and displayed in an autostereoscopy. The recovered imaging is presented with removal of the background interference to demonstrate the general applicability for camouflage breaking with stereo imaging and sensing.

Many studies have demonstrated hydrogen's therapeutic and preventive effects on various diseases. Its selective antioxidant properties against hydroxyl radicals, which are responsible for the indirect effects of ionizing radiation, may make it worthy of attention as a new radio-protector. We recently developed new hydrogen water that is more stable and has higher antioxidant activity by using ultra-fine bubbles. In this study, female C57BL/6J mice given ad libitum access to ultra-fine bubble hydrogen water (UBHW) were subjected to whole-body irradiation (WBI) with X-rays, and the radio-protective effect of UBHW was evaluated. Sub-lethal WBI resulted in a 30-day survival rate of 100% in UBHW-fed mice, compared with 37% in control mice. In the case of lethal WBI, while the control mice died out in about 3 weeks, the 30-day survival rate improved to 40% by UBHW due to the high scavenging activity of hydroxy radicals. Twenty-six serum proteins involved in inflammatory and immune responses were significantly identified in UBHW-fed mice by proteomics, and UBHW may enhance and regulate these functions, resulting in reduced damage in mice exposed to WBI. We conclude that UBHW has good potential in radio-protection, with evidence that warrants further research efforts in this field.

This study investigates uranium solvent extraction under AMEX process conditions. The use of pure extractants without diluents or phase modifiers allows not only to reduce the use of volatile organic compounds, but also to provide higher extraction yields without third phase formation. Pure extractants are protonated amines or quaternary ammoniums with suitable counter ion, which act at the interface between ion pairs and protic ionic liquids. The mixture of sulfates anion (SO42-) and bis(trifluoromethanesulfonyl)imide anion (NTf2-) revealed unexpected nonlinear extraction behaviors, which appear highly important to rationalize for optimized application. Spectroscopic analysis (NMR, UV-vis, FT-IR, and EXAFS) showed that uranium extraction occurs via protonated amine and three sulphates. Nonlinear extraction could further be interpreted by considering water and acid transfer between the two phases: at lower sulphate ratios, the release of acid from the organic phase into the aqueous phase was shown to influence the number of protonated amines in the organic phase, affecting uranium extraction before its enhancement. Furthermore, the extraction loss at higher sulphate ratios, was assigned to the destabilization of bidentate uranium-sulphate complexes due to a competition between water and sulphates.

Pretreatment of cells with proteolysis inhibitors diminished intensity and changed shape of DNICs specific EPR signal in a treatment time-dependent manner. The level of DNIC formation was significantly influenced by the presence of protein degradation products. Interestingly, formation of HMWDNICs depended on the availability of LMWDNICs. The extent of glutathione involvement in the in vivo formation of DNICs is minor yet noticeable, aligning with our prior research findings.

Pulmonary sarcoidosis is a multisystem granulomatous interstitial lung disease (ILD) with a variable presentation and prognosis. Early accurate detection of pulmonary sarcoidosis may prevent progression to pulmonary fibrosis, a serious and potentially life-threatening form of the disease. However, the lack of a gold-standard diagnostic test and specific radiographic findings pose challenges in diagnosing pulmonary sarcoidosis. Chest computed tomography (CT) imaging is commonly used but requires expert, chest-trained radiologists to differentiate pulmonary sarcoidosis from lung malignancies, infections, and other ILDs. In this work, we developed a multichannel, CT and radiomics-guided ensemble network (RadCT-CNNViT) with visual explainability for pulmonary sarcoidosis vs. lung cancer (LCa) classification using chest CT images. We leverage CT and hand-crafted radiomics features as input channels, and a 3D convolutional neural network (CNN) and vision transformer (ViT) ensemble network for feature extraction and fusion before a classification head. The 3D CNN sub-network captures localized spatial information of lesions, while the ViT sub-network captures long-range, global dependencies between features. Through multichannel input and feature fusion, our model achieved the highest performance with accuracy, sensitivity, specificity, and combined AUC of 0.93±0.04, 0.94±0.04, 0.93±0.08 and 0.97 respectively in a 5-fold cross-validation study with pulmonary sarcoidosis (n=126) and LCa (n=93) cases. The model offers promising potential for improving the diagnosis of pulmonary sarcoidosis. A detailed ablation study showing the impact of CNN+ViT compared to CNN or ViT alone, and CT+radiomics input, compared to CT or radiomics alone, is also presented in this work.

Cystic artery bleeding (CAB), a relatively uncommon entity, can arise from both traumatic and non-traumatic etiologies. This pictorial essay aims to elucidate the computed tomography (CT) findings associated with CAB in these distinct contexts. In traumatic CAB, particularly blunt or penetrating trauma, a cystic artery lesion is the culprit behind the hemoperitoneum characteristically located within the gallbladder fossa. Prompt diagnosis is crucial. Fortunately, trans-arterial embolization offers a successful treatment option for traumatic cystic artery lesions, especially in settings where non-operative management is preferred. Non-traumatic CAB, on the other hand, often stems from inflammation in the hepatobiliary and pancreatic system, gallbladder tumours, or iatrogenic injuries. The underlying mechanism typically involves cystic artery wall damage, either due to inflammation or procedural complications, leading to the formation of a cystic artery pseudoaneurysm (CAP). Notably, CAP bleeding can manifest long after the causative event, posing a diagnostic challenge with a variable clinical presentation. This pictorial essay serves to illustrate the CT signs and features of CAB in both traumatic and non-traumatic scenarios. Additionally, it will delve into the characteristic CT appearance of CAP.

Backyard chickens often suffer from foot pad dermatitis (FPD), a condition exacerbated by poor husbandry, nutritional deficiencies, and obesity. Pressure-relieving bandages, commonly used in treatment of FPD, are impractical for outdoor chickens as they quickly become wet and dirty, necessitating daily changes which are often unfeasible. This retrospective study explores the use of custom-fit silicone shoes, created via 3D-printed molds, as an alternative to traditional bandages. CT scans were used to design shoes, adapted from a design used for birds of prey. Over three years, 16 chickens with varying degrees of FPD were treated. The results demonstrated that sili-cone shoes were an effective treatment for FPD, allowing outdoor activity, and facilitated daily lesion care without frequent bandage changes. The median shoe-wearing period was 14 days, and most owners provided positive feedback. Despite some attachment issues, the occurrence of sec-ondary pressure marks and feather regrowth challenges, the silicone shoes offered better ventila-tion, reusability, and consistent pressure relief compared to traditional bandages. This study con-cludes that silicone shoes are a viable solution for managing FPD in backyard chickens, promoting faster healing and improved owner compliance.

The aging mechanism of 10% and 30% nickel substituted manganese hexacyanoferrate cathode material in aqueous zinc-ion batteries has been explored through the advanced synchrotron-based two-dimensional x-ray fluorescence technique. Thanks to the two-dimension modality, not only the metal concentration dynamics throughout the entire electrodes was followed during the aging process, but their spatial distribution was also revealed, suggesting the route of the material transformation. The dissolution of Mn and Ni, and the penetration of Zn inside the framework, alongside the Mn aggregations outside the hexacyanoferrate framework were detected. Additionally, the possibility of conducting x-ray absorption spectroscopy measurements on the regions of interest made it possible to explore the chemical state of each metal, and furthermore, synchrotron-based powder x-ray diffraction demonstrated the gradual structural modification in 30% Ni-containing sample series, in terms of the different phase formation.

In this work, Gd-filled skutterudite GdxCo4Sb12 has been prepared in one-step method under high-pressure conditions in a piston-cylinder press at 3.5 GPa and moderate temperature of 800 °C. A detailed structural characterization was performed using synchrotron X-ray diffraction (SXRD), revealing a filling fraction of x = 0.066(4) and an average &lt;Gd–Sb&gt; bond length of 3.3499(3) Å. The lattice thermal expansion accessed via temperature-dependent SXRD led to a precise determination of a Debye temperature of 322(3) K, from the fitting of the unit-cell volume expansion using the second order Grüneisen approximation. Such parameter, when evaluated from the mean square displacements of Co and Sb, displayed a value of 265(2) K, meaning that the application of the harmonic Debye theory underestimates the Debye temperature in skutterudites. Regarding the Gd atom, its intrinsic disorder value is ~5× and ~25× higher than those of Co and Sb, respectively, denoting that Gd has a strong rattling behavior with an Einstein temperature of θE = 67(2) K. As a result, an ultra-low thermal conductivity of ~0.89 W/m·K at 773 K was obtained, leading to a thermoelectric efficiency zT of ~0.5 at 673 K.

For the first time, the effect of a significant change in the resistance of the aquatic environment of a population of protozoan microorganisms under the influence of radiofrequency electromagnetic radiation from cell phones has been experimentally studied. The results of the experiment demonstrate the biological nature of the changes occurring in the “water population of protozoa” system, which indicates that the impact of radiation directly affects the cell. This conclusion is confirmed by the same order of magnitude time of information exchange between individual individuals of the population in the calculation and in the experiment. An extremely low concentration of protozoa in the experiment was established, equal to 1000 pcs./liter, at which the indicated effect is observed.An unambiguous dependence of the biological effect in the “water – amoeba population” system on the average power of electromagnetic radiation of cell phones, both in standby mode and in talk mode, has been established. It is concluded that the presented method of changing the physical properties of the aquatic environment of a population of protozoa under the influence of electromagnetic fields can be a model experiment in identifying the mechanisms of interaction of biological systems with electromagnetic radiation, determining the response time of biological systems to external electromagnetic influence, and establishing the degree of influence of radiation in the 4G, 5G ranges.

Re-investigation of the chemical composition of the annual plant Mitracarpus scaber Zucc. led to the identification of clarinoside, a new pentalogin derivative containing a rare quinovose moiety, and the known compound harounoside. While the planar structure was fully determined using tandem MS and quantum mechanics calculations (QM), the tridimensional structure was unravelled after isolation and NMR analysis. The absolute configuration was assigned by comparison of experimental and theoretical SRCD spectra. Both compounds were tested for anti-inflammatory activity and compound 1 showed the ability to inhibit the production of interleukin-8 (Il-8) with an IC₅₀ of 9.17 µM.

Cardiotoxicity is an unwanted side-effect arising from different medications. The term describes a diminution of heart function, affecting especially left ventricular ejection fraction, which can progress to heart failure. Pediatric oncology patients treated with drugs of the anthracycline group, e.g., doxorubicin, can evolve to heart failure patients in adult age. Nuclear Medicine imaging of fatty acid oxidation and glycolysis accurately describes normal and altered heart metabolism. The most common finding is a state of cardiac glycolysis, which is reflected by increased uptake of 18F-desoxyglucose (18F-FDG) at a time when fatty acid oxidation is decreased. Glycolysis has recently been recognized as being the result of coenzyme Q10 deficiency as part of adaptation to hypoxia. Low LEVF correlates with impaired fatty acid oxidation. This deficiency can arise from chemotherapy and radiation and can be corrected by supplementation. Drugs like enalapril can improve fatty acid utilization. We will review relevant Nuclear Medicine imaging studies as well as fundamental biochemical data that demonstrate this pathogenetic path.

Abiotic stress is responsible for significant reduction in crop plant productivity worldwide. Ultraviolet (UV) radiation is a natural component of sunlight and a permanent environmental stimulus. This study investigated the distinct responses of young wheat and einkorn plants to excessive UV-B radiation (180 min at λmax 312 nm) following foliar pretreatment with 1 µM synthetic cytokinin 4PU-30. Results demonstrated that UV radiation significantly amplified hydrogen peroxide levels in both wheat and einkorn, with einkorn exhibiting more pronounced increase compared to wheat. This elevation indicated the induction of oxidative stress by UV radiation in the two genotypes. Intensified antioxidant enzyme activities and increased accumulation of typical stress markers and non-enzyme protectants were evidenced. Transcriptional activity of genes encoding key antioxidant enzymes was also investigated aiming to elucidate the genetic regulation of the antioxidant systems in both wheat and einkorn seedlings. Our results suggested a role for POX1 and POX7 genes in the UV-B tolerance of the two wheat species as well as a cytokinin stimulated UV-B stress response in einkorn mediated through upregulation of the tau subfamily gene GSTU6. Based on these findings it could be concluded that 4PU-30 had the potential of alleviating oxidative stress by attenuating the symptoms of superfluous UV-B illumination in the two examined plant species.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

The article presents the results of the γ-ray and fast neutrons impact on various rice species, in order to obtain mutant forms resistant to salinity (NaCl) and drought factors (sorbite). They are going to be used as initial forms in synthetic selection when creating varieties, adapted to the stressful conditions of, both, soil and climate in the Kazakhstan Aral Sea. The average lethal doses (LD50) of γ-rays and fast neutrons, as well as, the average NaCl and sorbite lethal concentrations were established. A distinct dependence on the effect of ionizing radiation and stress factors on the number of induced resistant mutant forms has been related to the initial rice variety. The largest number of mutant forms was obtained from the local variety Syr Suluy, followed by Leader and Aikerim varieties. Out of all varieties, only 1% of the initially irradiated by γ-rays seeds survived, while after fast neutron irradiation – 4,3%. M1 mutant plants significantly differ from the initial forms in terms of morphological features – plant height, panicle length, and grain size. They are tolerant to lodging, and have short and highly sterile panicles, indicating that they are mutants.

Brain is the most complex organ in the human body and it is divided into two hemispheres - left and right hemispheres. Left hemisphere is responsible for control of right side of our body whereas right hemisphere is responsible for control of left side of our body. Brain image segmentation from different neuroimaging modalities is one of the important parts in clinical diagnostic tools. Neuroimaging based digital imagery generally contain noise, inhomogeneity, aliasing artifacts, and orientational deviations. Therefore, accurate segmentation of brain images is a very difficult task. However, the development of accurate segmentation of brain images is very important and crucial for a correct diagnosis of any brain related diseases. One of the fundamental segmentation tasks is to identify and segment inter-hemispheric fissure/mid-sagittal plane, which separate the two hemispheres of the brain. Moreover, the symmetric/asymmetric analyses of left and right hemispheres of brain structures are important for radiologists to analyze diseases such as Alzheimer's, Autism, Schizophrenia, Lesions and Epilepsy. Therefore, in this paper we have analyzed the existing computational techniques used to find brain symmetric/asymmetric analysis in various neuroimaging techniques (MRI/CT/PET/SPECT), which are utilized for detecting various brain related disorders.

Accurate treatment planning in radiotherapy essentially decreases secondary damage to healthy tissue surrounding the tumor. Due to plans to use a direct, highly collimated, narrow beam with high intensity to treat small area tumors, researchers have studied microbeam radiation therapy extensively. Using a synchrotron beam as the radiation source may help to limit secondary damage, but treatment planning using computerized simulations and dosimetry is still necessary to achieve optimal results. For this purpose, PDA-gel dosimeters were developed and their sensitivity around a 150 keV induced synchrotron X-ray radiation beam was examined via Monte Carlo simulations using the EGS5 code system. The microbeam development is now at the animal study stage. In this study, we simulate the irradiation of a rat's brain. The simulation results obtained spectra for two types of PDA-gel dosimeters that were compared with the spectrum obtained in a modelized brain tumor of a rat. Additionally, percentage depth dose curves were calculated for the brain tissue and the two gels. Correction equations for the dosimeters were obtained from the dose-difference plots. For further references, these equations can be used to calculate the actual dose in a brain tumor in a rat. The Monte Carlo simulations demonstrate that PDA-gel dosimeters can be used as a reference technique in planning treatment using synchrotron irradiations and in other medical treatment planning methods.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Metasurface constitutes one of the most promising technologies for holographic imaging; however, the work for terahertz (THz) metasurface holographic imaging is relatively limited. Here, we propose a THz dielectric geometric-propagation phase metasurface, which can operate dual-mode (reflection and transmission) and reconfigurable multifunctional holographic imaging. The dual-mode is realized by controlling the Fermi energy level (Ef) of the graphene integrated into the metasurface unit, and the reconfigurable three-channel holographic imaging in reflection or transmission mode are achieved by switching the feed polarization among left-handed circular polarization (LCP), right-handed circular polarization (RCP) and linear polarization (LP). The metasurface is designed based on the transmission mode, and a physical model for switching to the reflection mode is established. For the first time to the best of our knowledge, a reflection-transmission dynamic modulation THz holographic imaging metasurface has been developed. The holographic metasurface operates in transmission mode at Ef = 0.1 eV, and in reflection mode at Ef = 0.9 eV. Compared with recently published holographic imaging metasurfaces, the proposed metasurface offers the following advantages: high holographic efficiencies (42.5% to 49%), more holographic imaging channels, dynamic modulation dual-mode operations, and reconfigurability.

Short video addiction refers to a psychological dependency on short video applications, characterized by an intense attachment and an inability to control usage, leading to typical addiction symptoms. While its definition bears similarities to substance addiction, significant differences also exist. According to the Diagnostic and Statistical Manual of Mental Disorders, Fifth Edition (DSM-5), published in 2013, short video addiction has not yet been officially classified as an addiction disorder. To facilitate more in-depth and standardized research on short video addiction, it is essential to synthesize and organize existing studies on its theoretical foundations and mechanisms.

Keywords: olfactory rehabilitation; chronic pain; fMRI;

Effective solar forecasting has become a critical topic in the scholarly literature in recent years due to the rapid growth of photovoltaic energy production worldwide and the inherent variability of this source of energy. Due to the technological and econonomic limitations of energy storage solutions, using other, mosty conventional, sources to cover energy shortfalls and at the same time utilising solar surpluses production becomes necessary. The need to optimize energy systems, ensuring power continuity, and balancing energy supply and demand has led to the development of various forecasting methods and approaches based on meteorological data or photovoltaic plant characteristics. This article presents the results of a meta-review of the solar forecasting literature, including the current state of knowledge and methodological discussion. It presents a comprehensive set of forecasting methods, evaluates current classifications, and proposes a new synthetic typology. The article emphasizes the increasing role of artificial intelligence (AI) and machine learning (ML) techniques in improving forecast accuracy, alongside traditional statistical and physical models. It explores the challenges of hybrid and ensemble models, which combine multiple forecasting approaches to enhance performance. The paper addresses the emerging trends in solar forecasting research, such as the integration of big data and advanced computational tools. Additionally, from a methodological perspective, the article outlines a rigorous approach to the meta-review research procedure, addresses the scientific challenges associated with conducting bibliometric research, and highlights best practices and principles. This includes defining research questions, selecting eligibility criteria, literature search, data extraction, synthesis, and assessing bias and quality. The article contributes to the solar forecasting field by providing up-to-date knowledge, along with insights on the emerging trends, future research directions, and anticipating implications for the theory and practicce.

Hyperspectral imaging data holds great potential for various stages of the mining life cycle in active and abandoned mines. The technology, however, has yet to achieve large-scale industrial implementation and acceptance. While hyperspectral satellite im-agery yields high spectral resolution, high signal-to-noise ratio (SNR), and global availability with breakthrough satellite sys-tems like EnMAP, EMIT, and PRISMA, limited spatial resolution poses challenges for mining sectors, which require decimeter- to centimeter-scale spatial resolution for applications such as reconciliation, ore/waste estimates, geotechnical assessments, and en-vironmental monitoring. Hyperspectral imaging from drones (Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the pit/ mine scale, with the capability for frequent, user-defined re-visit times. Collecting data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions offers to detect different minerals and surface alteration patterns, potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we review of applicable instrumentation, software components, and relevant studies deploying hyperspectral imaging in or appropriate to the mining sector, especially for hyperspectral VNIR-SWIR UASs. If directly applicable, draw on previous insights derived from airborne, satellite, and ground-based imaging systems. We also discuss common practices for UAS survey planning and sampling considerations for interpretation.

To address the requirements of sonar imaging, such as high receiving sensitivity, wide bandwidth, wide receiving angle, an AlN PMUT with an optimized ratio of 0.6 for the piezoelectric layer diameter to backside cavity diameter is proposed in this paper. A sample AlN PMUT is designed and fabricated with SOI substrate-based bulk MEMS process. The characterization test result of the sample demonstrates a -6 dB bandwidth of approximately 500 kHz and a measured receiving sensitivity per unit area of at 1.37 V/μPa/mm2, which significantly surpasses the performance of previously reported PMUTs. The -6 dB horizontal angles of the AlN PMUT at 300 kHz and 500 kHz are measured 68.30° and 54.24°, respectively. To achieve an accurate prediction of its characteristics when being packaged and assembled in a receive array, numerical simulations with the consideration of film stress are conducted. The numerical result shows a maximum deviation of ±7% in the underwater receiving sensitivity across the frequency range of 200 kHz to 1000 kHz and a deviation of about 0.33% in the peak of underwater receiving sensitivity comparing to the experimental data. By such good agreement, the simulation method reveals its capability of providing theoretical foundation for enhancing the uniformity of the AlN PMUTs in future studies.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

Abstract: Giant Cell Arteritis (GCA) is an autoimmune/autoinflammatory disease affecting large vessels in patients over 50 years old. The disease presents as an acute inflammatory response with two phenotypes, cranial-GCA and Large Vessel Vasculitis (LV)-GCA, involving the thoracic aor-ta and its branches. 18F-fluorodeoxyglucose positron emission tomography-computed tomogra-phy (18F-FDG PET-CT) is among the imaging techniques contributing to diagnosis of patients with systemic disease. However, its association with soluble inflammatory markers is still elu-sive. This proof-of-concept study aims to identify novel soluble serum biomarkers in PET/CT pos-itive patients with LV-GCA and associate them with active (0 months) and inactive disease (6 months following treatment), in sequential samples. The Most-Disease-Segment Target-to-Background Ratio (TBRMDS) was calculated for 9 LV-GCA patients, while 12 cranial-GCA and 7 Polymyalgia Rheumatica patients with negative initial PET/CT served as disease controls. Serum macrophage-related cytokines were evaluated by Cytometric Bead Array (CBA). Finally, previously published NMR-metabolomics data acquired at the same blood sampling were associated with PET/CT findings. TBRMDS was significantly increased in active versus inactive disease (3.45 vs. 2.55, p=0.008). The analysis identified 6 serum metabolites, as more sensitive to change from the active to inactive state. Among them, choline levels were exclusively altered in the LV-GCA group, but not the disease controls. Cytokine levels were not associated with PET/CT activity. Combining with CRP, ESR, and TBRMDS a composite index was generated to depict well the differences between active and inactive systemic LV-GCA (25.45 vs 11.45, p=0.0039). These preliminary results could pave the way for more extensive studies integrating serum metabolomic parameters with PET/CT imaging data to extract sensitive composite disease indexes useful for the everyday clinical practice.

Objective: To explore the hot spots and development trends of community public health research. Methods: The literature related to this topic was searched in CNKI and PubMed databases, and the trend map of the number of articles was drawn according to the obtained data. The included literature were analyzed with Vosviewer software for keyword and author co-occurrence, and CiteSpace 6.3.R1 Basic software was used for mechanism co-occurrence, key emergence and clustering analysis, and timeline distribution map drawing. Results: 189 Chinese literature and 77 English literature were selected. The Chinese literature focused on “community public health service, emergency management, and community governance”, and the research trend was “community public health emergency management and community governance”; English literature focuses on “nursing education, health education, human qualitative research”. Conclusion: Although the Chinese and English literature shows that scholars in this field have different emphases, the primary community health is the key and difficult point to realize the national public health service project, and improving the basic public health service in the primary community is related to the health of all the people, so it is very important.

This study utilized electrical resistivity imaging (ERI) to investigate subsurface characteristics near Nicolaus Copernicus University Polar Station on the western Spitsbergen-Kaffiøyra Plain, island in the Svalbard archipelago. Surveys along two lines, LN (148 meters) collected in 2022 and 2023 and ST (40 meters) collected in 2023, were conducted to assess resistivity and its correlation with ground temperatures. The LN line revealed a 1 to 2 meters thick resistive unsaturated outwash sediment layer, potentially indicative of permafrost. Comparing LN resistivity result between 2022 and 2023, a 600 Ohm-m decrease in the unsaturated active layer in 2023 was observed, attributed to a 5.8℃ temperature increase, suggesting a link to global warming. ERI along the ST line depicted resistivity reaching its minimum at approximately 1.6 meters, rising to over 200 Ohm-m at 4 meters, and slightly decreasing to around 150 Ohm-m at 7 meters. Temperature measurements from the ST line's monitoring well confirmed permafrost at a depth of 1.6 to 2 meters. Additionally, water content distribution in the ST line was estimated after temperature correction, revealing a groundwater table depth of approximately 1.06 meters, consistent with measurements from the S4 borehole on the ST line. This study provides valuable insights into Arctic subsurface dynamics, emphasizing the sensitivity of resistivity patterns to climate change and offering a comprehensive understanding of permafrost behavior in the region.