Dynamic systems which underly controlled systems are expected to increase in complexity as robots, devices, and connected networks become more intelligent. While classical stable systems converge to a stable point (a sink), another type of stability is to consider a stable path rather than a single point. Such stable paths can be made of saddles which draw in trajectories from certain regions, and then push the trajectory toward the next saddle point. These are chains of saddles are called stable heteroclinic channels (SHCs), and can be used in robotic control to represent time sequences. While we have previously shown that each saddle is visualizable as a trajectory waypoint in phase space, how to increase the fidelity of the trajectory was unclear. In this paper, we hypothesized that the waypoints can be individually modified to locally vary fidelity. Specifically, we expected that increasing the saddle value (ratio of saddle eigenvalues) causes the trajectory to slow to more closely approach a particular saddle. Combined with other parameters that control speed and magnitude, a system expressed with an SHC can be modified locally, point by point, without disrupting the rest of the path, supporting their use in motion primitives. However, even more complex trajectory shape modifications are possible. While some combinations can enable a trajectory to better reach into corners, other combinations can rotate, distort and round the trajectory in the region of a corner. In our example, modifying select saddle values produced a 32% decrease in the trajectory error of a complex trajectory produced using this system. This is an effect not visible in previous 1D studies, that can lead to different learnable and tunable representations of dynamic systems.

Channel bends are one of the most important characteristic features of natural streams. These bends often create the conditions for a hyporheic zone, which has been recognized as a critical component of stream ecosystems. The streambed vertical hydraulic conductivity (K_v), vertical hydraulic gradient (VHG) and Darcian flux (DF) in the hyporheic zone were estimated at 61 locations along a channel bend of the Beiluo River during July 2015 and January 2016. All the streambed attributes showed great spatial variability along the channel bend. Both upward fluxes and downward fluxes occurred during the two test periods, most of studied stream sections were controlled by downwelling, indicating stream water discharge into the subsurface. The average downward flux was higher at the downstream side than at the upstream side of the channel bend, especially in July 2015. The distribution of streambed sediment grain size has a significant influence on the variability of K_v; high percentages of silt and clay sediments generally lead to low K_v values. Higher K_v at the depositional left bank at the upstream site shifted toward the erosional right bank at the downstream site, with K_v values positively correlated with the water depth. This study suggested that the variabilities of K_v and VHG were influenced by the stream geomorphology and that the distribution of K_v was inversely related, to a certain extent, to the distribution of VHG across the channel bend. K_v and VHG were found to have opposite effects on the DF, and the close relationship between K_v and DF indicated that the water fluxes were mainly controlled by K_v.

The protein TRPM8, a non-selective, calcium (Ca2+) permeable ion channel is implicated in several pathological conditions, including neuropathic pain states. In our previous research endeavors, we have identified β–lactam derivatives with high hydrophobic character that exhibit potent and selective TRPM8 antagonist activity. This work describes the synthesis of novel derivatives featuring C-terminal amides and diversely substituted N’-terminal monobenzyl groups, in an attempt to increase the total polar surface area (TPSA) in this family of compounds. The primary goal was to assess the influence of these substituents on the inhibition of menthol-induced cellular Ca2+ entry, thereby establishing critical structure-activity relationships. While the substitution of the tert-butyl ester by isobutyl amide moieties improved the antagonist activity, none of the N’-monobencyl derivatives, regardless of the substituent on the phenyl ring, achieved the activity of the model dibenzyl compound. The antagonist potency of the most effective compounds was subsequently verified using Patch-Clamp electrophysiology experiments. Furthermore, we evaluated the selectivity of one of these compounds against other members of the TRP ion channel family and some receptors connected to peripheral pain pathways. This compound demonstrated specificity for TRPM8 channels. To better comprehend the potential mode of interaction, we conducted docking experiments to uncover plausible binding sites on the functionally active tetrameric protein, which come upon four main poses by the pore zone, differents from those described for other known antagonists. Finally, in vivo experiments, involving a couple of selected compounds, revealed significant antinociceptive activity within a mice model of cold allodynia induced by oxaliplatin.

Transient receptor potential melastatin-8 (TRPM8) is a cation channel that is activated by cold and “cooling agents” such as menthol and icilin, which induce a cold sensation. Stimulation of TRPM8 activates an intracellular signaling cascade that ultimately leads to a change in the gene expression pattern of the cells. Here, we investigated the TRPM8-induced signaling pathway that links TRPM8 channel activation to gene transcription. Using a pharmacological approach, we show that inhibition of phosphatidylinositol 4-phosphate 5 kinase alpha (PIP5K), an enzyme essential for the biosynthesis of phosphatidylinositol 4,5-bisphosphate, attenuated TRPM8-induced gene transcription. Analyzing the link between TRPM8 and Gq proteins, we show that pharmacological inhibition of the beta gamma subunits impairs TRPM8 signaling. In addition, genetic studies showed that TRPM8 requires an activated Galpha subunit for signaling. In the nucleus, the TRPM8-induced signaling cascade triggers an activation of the transcription factor AP-1, a complex consisting of a dimer of basic region leucine zipper (bZIP) transcription factors. Here, we identified the bZIP protein c-Jun as an essential component of AP-1 within the TRPM8-induced signling cscade. In summary, with PIP5K, Gq subunits and c-Jun we have identified key molecules in the TRPM8-induced signaling from the plasma membrane to the nucleus.

Dynamic optical structural color is always desired in various display applications and usually involves active materials. Full-color generation, especially bi-directional full-color generation in both reflective and transmissive modes, without any active materials included has been rarely investigated. Herein, we demonstrate a scheme of bi-directional full-color generation based on a plasmonic metasurface modulated by rotation of the polarization angle of the incident light without varying the geometry and the optical properties of the materials and the environment where the metasurface resides. The metasurface unit cell consists of plasmonic modules aligning in three directions and is patterned in a square array. The metasurface structural color device generates full colors in both reflection and transmission. Based on the proposed polarization-dependent structural color, information encoding of three multiplexed animal images and quick-responsive (QR) codes is demonstrated to verify the efficient information encoding and decoding of the proposed scheme. The animals can be seen under different polarization incidence and the QR codes can be successfully decoded by the polarization rotation in transmission. The proposed bi-directional full-color generation metasurface has great potential in applications such as kaleidoscope generation, anti-counterfeiting, dynamic color display, and optical information encoding.

An accurate assessment of the stage-discharge relationship in open channel flows is necessary and important to the design and management of hydraulic structures and engineering in practical hydrosystems such as rivers and streams. While the flow structures and patterns at open channel junctions are interesting and have been widely studied in the literature, this paper focuses further on the effect of flow junctions on stage-discharge relationship at mountain river confluences. In this study, both the flume and physical model experiments are designed and performed carefully to test and analyze the complex flow structures and characteristics at river confluences with different configurations and hydraulic conditions. The impacts of the flow junctions on the traditional stage-discharge relationship are analyzed in this study. The results of this study are discussed in the paper for the understanding of flow structures at flow junctions and the design and management of hydraulic structures in river engineering.

Finding a good MIMO system model also major issue in Wireless Communication system. It is facing with so many problem, one of the major problem is finding good system model in terms of capacity and transmitting antenna system. In this paper, we analyze the channel capacity of various MIMO system model with some constant SNR level and outage probability. We establish a novel idea for MIMO system models as consider as 2^N- MIMO system model and find-out change in channel capacity when different transmitting antennas with constant SNR and outage probability. The channel capacity ratio CC_R is presented here on the basis of 2^N- MIMO channel capacity model. Number of transmitted antenna presented in MIMO system is increases is well-known however paper shows change in capacity in simple form.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Hypertension is a frequent risk factor for cardiovascular diseases and the prevalence rate is continuously rising. Multiple pathophysiological mechanisms are responsible for hypertension, necessitating a combination of drugs from different classes for best management. Combination therapy is five times more effective in decreasing blood pressure compared to escalating the dose of a single agent. As per the ACCOMPLISH trial analysis, coupling a renin-angiotensin system inhibitor with a calcium channel blocker is more effective than the combination of a renin-angiotensin system inhibitor with diuretics in reducing major cardiovascular events, cardiovascular-related mortality, and the progression of chronic kidney disease. The renin-angiotensin system can be suppressed by inhibiting the angiotensin-converting enzyme or angiotensin type 1 receptor (AT1R), resulting, in decreased vascular smooth muscle contraction, heart performance, and reduced aldosterone synthesis. Calcium channel blockers work by inhibiting L-type calcium channels, reducing heart performance via negative inotropic, chronotropic, and bathmotropic effects, along with reducing vascular smooth muscle contraction. Diuretics exert their antihypertensive impact by changing body fluid volume and electrolytes. Initially, hypertension treatment commences with a single medication but often, different classes of two or more antihypertensive medications are necessary for achieving the target blood pressure goal. Sometimes, for Resistant hypertension four different classes of antihypertensive medications are necessary to reach the target blood pressure goal.

A new design scheme is proposed for twisting the walls of a microchannel, and its performance is demonstrated numerically. The numerical study was carried out for a T-shaped microchannel with twist angles in the range of 0 to 34π. The Reynolds number range was 0.15 to 6. The T-shaped microchannel consists of two inlet branches and an outlet branch. The mixing performance was analyzed in terms of the degree of mixing and relative mixing cost. All numerical results show that the twisting scheme is an effective way to enhance the mixing in a T-shaped microchannel. The mixing enhancement is realized by the swirling of two fluids in the cross section and is more prominent as the Reynolds number decreases. The twist angle was optimized to maximize the DOM, which increases with the length of the outlet branch. The twist angle was also optimized in terms of the relative mixing. The two optimum twisting angles are generally not coincident. The optimum twist angle shows a dependence on the length of the outlet branch but it is not affected much by the Reynolds number.

Low-loss photonic waveguides in lithium niobate offer versatile functionality as nonlinear frequency converters, switches, and modulators for integrated optics. Combining the flexibility of laser processing with liquid phase epitaxy we have fabricated and characterized lithium niobate channel waveguides on lithium niobate and lithium tantalate. We used liquid phase epitaxy with K2O flux on laser-machined lithium niobate and lithium tantalate substrates. The laser-driven rapid-prototyping technique can be programmed to give machined features of various sizes, and liquid phase epitaxy produces high quality single-crystal, lithium niobate channels. The surface roughness of the lithium niobate channels on a lithium tantalate substrate was measured to be 90 nm. The lithium niobate channel waveguides exhibit propagation losses of 0.26 ± 0.04 dB/mm at a wavelength of 633 nm. Second harmonic generation at 980 nm was demonstrated using the channel waveguides, indicating that these waveguides retain their nonlinear optical properties.

Wall Shear Stress (WSS) abnormalities in carotid artery blood flow are key hemodynamic factors leading to arterial endothelial damage, atherosclerotic plaque formation, and carotid artery stenosis. Precise simulation of carotid artery blood flow WSS in vitro play an important role in understanding the underlying hemodynamic mechanism of carotid artery stenosis. This study presents a design for a microfluidic cell culture chamber with a variable cross-section and a step structure, leveraging microfluidic technology and principles of fluid dynamics. We propose an optimization strategy for microchannel dimensions based on Computational Fluid Dynamics (CFD) simulations. This strategy aims to replicate the distinct WSS waveform features found at various locations within the carotid bifurcation as observed in vivo. Our simulations indicate that with a step height of 0.09 mm, a width of 4 mm for the initial segment, and 5 mm for the subsequent wider channel, the device can effectively model the characteristics of low oscillatory WSS seen at sites of carotid sinus stenosis. Furthermore, it accurately represents the high-magnitude pulsatile WSS waveforms in the more uniform arterial sections downstream of the carotid sinus. The study also reveals that vortex formation and variations in low oscillatory WSS within the stepped section of the microchannel correlate with the step's height and width, as well as with the dimensions of the wider channel section. An increase in step width leads to a decrease in both the vortex area and the magnitude of negative WSS oscillations. When the step height is less than 0.03 mm, vortex formation is inhibited, challenging the simulation of low oscillatory WSS patterns. The variable cross-section microfluidic channel developed in this study provides a platform for simulating carotid artery WSS waveforms and facilitates research into the interplay between low oscillatory WSS at sites of carotid sinus stenosis and arterial endothelial dysfunction.

PIEZO channels PIEZO1 and PIEZO2 are the newly identified mechanosensitive, non-selective cation channels permeable to Ca2+. In higher vertebrates, PIEZO1 expresses ubiquitously in most of the tissues and cells while PIEZO2 expresses more specifically in the peripheral sensory neurons. PIEZO channels contribute to a wide range of biological behaviors and developmental processes, therefore driving a significant attention in the effort to understand their molecular properties. One prominent property of PIEZO channels is their rapid inactivation, which manifests itself as a decrease of channel open probability in the presence of a sustained mechanical stimulus. Lack of the PIEZO channel inactivation is linked to various mechanopathologies emphasizing the significance of studying this PIEZO channel property and the factors affecting it. In the present review, we discuss the mechanisms underlying the PIEZO channel inactivation, its modulation by interaction of the channels with lipids and/or proteins, and how the changes of PIEZO inactivation by the channel mutations can cause a variety of diseases in animals and humans.

We propose a deep-learning approach for the joint MIMO detection and channel decoding problem. Conventional MIMO receivers adopt a model-based approach for MIMO detection and channel decoding in linear or iterative manners. However, due to the complex MIMO signal model, the optimal solution to the joint MIMO detection and channel decoding problem (i.e., the maximum likelihood decoding of the transmitted codewords from the received MIMO signals) is computationally infeasible. As a practical measure, the current model-based MIMO receivers all use suboptimal MIMO decoding methods with affordable computational complexities. This work applies the latest advances in deep learning for the design of MIMO receivers. In particular, we leverage deep neural networks (DNN) with supervised training to solve the joint MIMO detection and channel decoding problem. We show that DNN can be trained to give much better decoding performance than conventional MIMO receivers do. Our simulations show that a DNN implementation consisting of seven hidden layers can outperform conventional model-based linear or iterative receivers. This performance improvement points to a new direction for future MIMO receiver design.

The combination of neural network and beamforming has been proved to be very effective in multi-channel speech separation. But its performance faces a challenge in complex environment. In this paper, an iteratively refined multi-channel speech separation method is proposed for the challenge, where the proposed is composed of initial separation and iterative separation. In initial separation, the time-frequency domain dual-path recurrent neural network neural network (TFDPRNN), minimum variance distortionless response (MVDR) beamformer and post-separation (also TFDPRNN) are cascaded for obtaining the first additional input in iterative separation. In iterative separation, the MVDR beamformer and post-separation are iteratively used, where the output of the MVDR beamformer is used as an additional input of the post-separation network and the final output comes from post-separation module. This iteration of the beamformer and post-separation is fully employed for promoting their individual optimization, which ultimately improves the overall performance of speech separation in multi-speaker scenarios. Experiments on the spatialized version of the WSJ0-2mix corpus show that our proposed method is significantly better than the current popular methods. In addition, the method also has a good effect on the dereverberation task.

Network Simulators (NS) is typically used to study services and applications in complex scenarios due to the infeasibility of deploying real testbeds. This is the case of Mobile Ad hoc Networks (MANETs) which can be extensively used in emergency situations or to gather information without infraestructure. An important factor to get realiable results in the MANETs’ simulations is the wireless channel module of NSs. In this report, we explain how thw wireless channel is implemented in NS-3 and it can be configured.

The structure of turbulent flow over non-flat surfaces is a topic of major interest in practical applications in both engineering and geophysical settings. A lot of work has been done in the fully rough regime at high Reynolds numbers where the effect on the outer layer turbulence structure and the resulting friction drag is well documented. It turns out that surface topology plays a significant role on the flow drag especially in the transitional roughness regime and therefore, hard to characterize. Survey of literature shows that roughness function depends on the interaction of roughness height, flow Reynolds number and topology shape. In addition, if the surface topology contains large enough scales then it can impact the outer layer dynamics and in turn modulate the total frictional force. Therefore, it is important to understand the mechanisms underlying drag increase from systematically varied surface undulations in order to better interpret quantifications based on mean statistics such as roughness function. In this study, we explore the mechanisms that modulate the turbulence structure over a two-dimensional (2D) sinusoidal wavy surface with a fixed amplitude, but varying slope. To accomplish this, we model the turbulent flow between two infinitely wide 2D wavy plates at a friction Reynolds number, $Re_{\tau}=180$. We pursue two different but related flavors of analysis. The first one adopts a roughness characterization flavor of such wavy surfaces. The second one focuses on understanding the non-equilibrium near surface turbulence structure and their impact on roughness characterization. Analysis of the different statistical quantifications show strong dependence on wave slope for the roughness function indicating drag increase due to enhanced turbulent stresses resulting from increased production of vertical velocity variance from the surface undulations.

The Inverted F Antenna (IFA) with the parasitic element on a finite conducting plane is proposed in the range frequency of 0.1 to 5.5 GHz and its characteristics are analyzed numerically. In this research, the parasitic element and the main IFA are investigated to obtain the resonance frequency for multiband operation purposes. The parasitic element is placed beneath adjusted to the main IFA to derive more frequency bands. The distance between the parasitic element and main horizontal element extremely affects the performance of the IFA. It is found that when the parasitic element is located closer to the conducting plane, this element is coupled by the current on the conducting plane. Consequently, the return loss bandwidth becomes narrower. Therefore, the gain of the proposed IFA becomes a bit higher. The antenna gain is about 8.21 dB at band #3 (λ_1.747), 7.43 dB at band #5 (λ_2.967) and 8.82 dB at band #6 (λ_4.023). This occurs when the calculation condition is antenna height h1 = 23 mm, h2 = 21 mm, horizontal antenna elements L = 173.2 mm, L1 = 140.9 mm and Lp = 152 mm, shorted element Ls = 30.7 mm, the distance between parasitic element and shorted element pyl = 5 mm. While the size of conducting plane is considered pxp+pxm by pyp+pym as 57.5+57.5 mm by 200+50 mm. In the numerical analysis, the electromagnetic simulator WIPL-D based on Method of Moment is used. The results show that the proposed IFA has UHF and SHF channel receiver which are suitable for advanced wireless service (band #3), mobile phones, Bluetooth, maritime service, radiolocation service (band #5) and radars, mobile phones, commercial wireless LAN (band #6).

Ion channels serve many cellular functions including ion homeostasis, volume regulation, signaling, nutrient acquisition, and developmental progression. Although the complex lifecycles of malaria parasites necessitate ion and solute flux across membranes, whole genome sequencing of the human pathogen, Plasmodium falciparum, revealed remarkably few orthologs of known ion channel genes. Contrasting with this, biochemical studies have implicated channel-mediated flux of ions and nutritive solutes across several membranes in infected erythrocytes. Here, I review advances in the cellular and molecular biology of ion channels in malaria parasites. These studies have implicated novel parasite genes in the formation of at least two ion channels, with additional ion channels likely present at various membranes and parasite stages. Computational approaches that rely on homology to known channel genes from higher organisms will not be very helpful in identifying the molecular determinants of these activities. Given their unusual properties, novel molecular and structural features, and essential roles in pathogen survival and development, parasite channels should be promising targets for therapy development.

In this paper, we develop a tractable mathematical model and emulation framework for communicating information through water using acoustic signals. Water is considered as one of the most complex mediums to model owing to its vastness and variety in characteristics depending on the scenario, what kind of water-body (lakes, rivers, tanks, sea etc.) and geographical location of the water-body is considered. Our proposed mathematical model involves the concept of damped harmonic oscillators to represent the medium (water) and Milne’s oscillator technique to map the interaction between the acoustic signal and water. Wave equations formulated for acoustic pressure and acoustic wave velocity are used to characterize the travelling acoustic signal. Signal strength, phase shift and time-delay generated from the mathematical model are fed to a Simulink-based emulator framework to generate channel samples and channel impulse responses. The emulator uses wide sense stationary uncorrelated scattering (WSSUS) assumption and finite sum-of-sinusoids (SOS) with uniformly distributed phase to generate the channel samples. Using the emulator platform it is possible to generate amplitude variation profile, Doppler shift and spread experienced by any travelling signal through different underwater communication scenarios. Such an emulator platform can be used to simulate different communication scenarios, underwater network topologies, data to train different learning models and predict performance of different modulation, multiplexing, error correction and multi-access techniques for underwater acoustic communications (UWAC) systems.

in this paper, the optical channel performance with respect to varying scintillation index parameters is studied. Where different channel effects are studied and analyzed. In free-space optical (FSO) communication, the major drawback of the optical communication system is the atmospheric turbulence (AT). This effect is nonlinear with optical channel altitude being changed. Therefore, the power margenal (PM) required for such a channel is also inconstant respectively. In this thesis, we analyze AT effect on the optical channel with different altitudes. Such that we found the difference in the range of PM required for such optical link distance. In our result, the Bit Error Rate (BER) VS. PM required is measured. The optical channel model is Log-Normal considered and the BER threshold BER^th = 10^-10 is taken.

In line with Pomeau’s conjecture about the relevance of directed percolation (DP) to turbulence onset/decay in wall-bounded flows, we propose a minimal stochastic model dedicated to the interpretation of the spatially intermittent regimes observed in channel flow before its return to laminar flow. Numerical simulations show that a regime with bands obliquely drifting in two stream-wise symmetrical directions bifurcates into an asymmetrical regime, before ultimately decaying to laminar flow. The model is expressed in terms of a probabilistic cellular automaton evolving von Neumann neighbourhoods with probabilities educed from a close examination of simulation results. It implements band propagation and the two main local processes: longitudinal splitting involving bands with the same orientation, and transversal splitting giving birth to a daughter band with orientation opposite to that of its mother. The ultimate decay stage observed to display one-dimensional DP properties in a two-dimensional geometry is interpreted as resulting from the irrelevance of lateral spreading in the single-orientation regime. The model also reproduces the bifurcation restoring the symmetry upon variation of the probability attached to transversal splitting, which opens the way to a study of the critical properties of that bifurcation, in analogy with thermodynamic phase transitions.

Ion channels contribute fundamental properties to all cell membranes. The ion channels are highly diverse in conductivity, structure, location and function. However, many of them can be regulated by common mechanisms, such as voltage or (de-)phosphorylation. Considering primarily pain-related ion channels, this review covers more novel and less known features of ion channel function, also with the aim to transfer knowledge between fields, which get inevitably more separate due to their size.

Security is a major topic in recent researchers, and finding new methods deliver was the motivations for this research to emphasize and as an awareness to browsers developers to handle images with more care and to enhance exploit detection technology in the browser, as this paper proves that hackers now can attack users with just an image.

Phα1β a spider peptide, purified from the venom of Phoneutria nigriventer inhibits high voltage calcium channels and is antagonist of TRPA1 receptor two important pain transduction path-ways. In the last 15 years, we have showed, in preclinical tests with Phα1β native and recombi-nant in rodent models of pain the potential of Phα1β to become a new analgesic drug. Evaluation of new drug on human ERG channel is requirement of the regulatory agencies. For the hERG channel inhibition assay it was used the commercial kit FLIPR® Potassium Assay. It was tested the effect of Phα1β and as positive control dofetilide, a well characterized hERG block-er. Phα1β 56, 225, 450 and 900 pMol caused at a higher concentration a very weak inhibition of the hERG channel activity of about 13.47 % with channel inhibition at 50%, IC50 > 900 pMol. Dofetilide (0.0001 - 10 µM), a known hERG inhibitor, caused a well-known, concentra-tion-dependent inhibition of the hERG channel with a mean IC50 of 0.1642 µM (0.1189 – 0.2282 µM. For the cytotoxicity assay, Phα1β concentrations of 56, 225, 450 and 900 pMol incubated for 24 h with HEK293-hERG cells did not alter the viability of the HEK293-hERG cells. It is con-cluded that Phα1β even at high concentrations does not interfere with hERG channels.

The cardiac sodium ion channel (NaV1.5) is a protein with four domains (DI-DIV), each with six transmembrane segments. Its opening and subsequent inactivation results in the brief rapid influx of Na+ ions resulting in the depolarization of cardiomyocytes. The neurotoxin veratridine (VTD) inhibits NaV1.5 inactivation resulting in longer channel opening times, and potentially fatal action potential prolongation. VTD is predicted to bind at the channel pore, but alternative binding sites have not been ruled out. To determine the binding site of VTD on NaV1.5, we performed docking calculations and high-throughput electrophysiology experiments. The docking calculations identified two distinct binding regions. The first site was in the pore, close to the binding site of NaV1.4 and NaV1.5 blocking drugs in experimental structures. The second site was at the “mouth” of the pore at the cytosolic side, partly solvent-exposed. Mutations at this site (L409, E417, and I1466) had large effects on VTD binding, while residues deeper in the pore had no effect, consistent with VTD binding at the mouth site. Overall, our results suggest a VTD binding site close to the cytoplasmic mouth of the channel pore. Binding at this alternative site might indicate an allosteric inactivation mechanism for VTD at NaV1.5.

Comparison between hydraulic and hydrologic computational methods is conducted in this study, regarding prismatic open channels under unsteady subcritical flow conditions. One-dimensional unsteady flow continuity and momentum equations are solved using explicit and implicit finite difference schemes for a symmetrical trapezoidal cross section, where the flow discharge and depth are the dependent variables. The results have been compared to those derived from Muskingum-Cunge hydraulic/hydrologic method as well as the commercial software HEC-RAS. The results from explicit and implicit code compare well to those from commercial software and hydraulic/hydrologic methods for long prismatic channels, thus directing the hydraulic engineer to quick preliminary design of prismatic open channels for unsteady flow with satisfactory accuracy.

For voltage-gated Ca2+ channel (VGCC), its α2δ subunits are traditionally considered to be auxiliary subunits that regulates VGCC trafficking to the plasma membrane. The antiepileptic, antinociceptive and anxiolytic gabapentin (GBP) has previously been shown to bind the VGCC α2δ subunits with high affinity to disrupt VGCC trafficking. Yet, the interaction between GBP and α2δ still remains poorly understood from a structural point of view. For instance, it is not clear yet what the structural implication is of α2δ-1-bound GBP against VGCC trafficking. With a set of experimental data-driven structural analysis of the VGCC α2δ-1 and its ligand GBP, this article postulates for the first time that: 1), α2δ-1 bound GBP stabilizes the α2δ-1-GBP complex structure; 2), α2δ-1 bound GBP restrains the conformational flexibility of α2δ-1; 3), α2δ-1-bound GBP establishes an electrostatic axis consisting of Q535 (Gln535)-R241 (Arg241)-GBP (gabapentin)-D452 (Asp452), which constitutes an energetically favourable contribution towards the structural stability of the α2δ-1-GBP complex and helps restrains the conformational flexibility and local structural rigidification of α2δ-1; and 4), GBP-induced local conformational inflexibility and structural rigidification of α2δ-1 is one key step in the pharmacological disruption of VGCC trafficking by GBP.

YouTube Kids serves as a dynamic and user-friendly resource for young learners to learn English. Its extensive library of instructional materials, which includes captivating animations and interactive movies, provides a rich and varied learning environment. Through the integration of play and exploration into language study, YouTube Kids creates a comfortable and engaging atmosphere that allows kids to improve their English language skills at their own pace. In this research article, a narrative literature review was employed as a qualitative methodology. Based on the gathered relevant literature, YouTube Kids presented such positive and negative impacts as a channel for English language acquisition. YouTube Kids is indeed a beneficial tool for young learners who are trying to learn English, but at the same time, it does have some potential disadvantages, as some videos may not employ the same standard or correctness of English, which could expose kids to improper grammar or pronunciation. Parents and teachers need to carefully select and keep an eye on the content their kids watch to ensure that their children's YouTube Kids content supports their language learning objectives. Through careful supervision and curation, parents and educators may maximize the usefulness of the site as a medium for teaching young learners English language skills while also minimizing any potential downsides.

Starting from the model of a slow-rolling missile with six degrees of freedom (6 DOF) in the body frame, a 6 DOF model in the Resal frame is obtained, which is used to linearize the coupled commanded motion. Based on the linearized model, we obtain the structural scheme of the commanded object and define the quality parameters. The obtained parameters have a complex representation (with real and imaginary parts) due to the coupling between longitudinal channels. Then, the kinematic guidance equations, the seeker equations and the actuator specific to the slow-rolling single-channel missile are defined using a switching function. The guidance kinematic equations, the seeker equations and the actuator model are linearized in the Resal frame, and the structural diagram of the homing missile is constructed. Starting from this, the characteristic polynomial having complex coefficients is determined and then analyzed with the Frank-Wall stability criterion. Based on the analysis, a stability range is determined for the navigation constant and a minimum and possibly a maximum limit for the time to hit the target is obtained. The stability range defined for the navigation constant on the linear model is finally validated on the nonlinear model in the body frame.

In the last decade, three-dimensional (3D) printing has allowed the field of complex microfluidic channels to expand rapidly towards channels with variable cross-sections (i.e., beyond simple rounded media with a constant diameter) and channels. Whose trajectory can be outside a single plane and has gained numerous macro- and nanoscale manufacturing advances. Three-dimensional printing is being explored for various biomedical applications and the fabrication of nanomedicines using additive manufacturing techniques. Employing 3D-printed templates for macro-to-micro interfacing, a passively operated microfluidic device was designed. The research seeks to fabricate a biodevice that enables insulin microdosing, creating a subsystem like a microvalve and a microchannel matrix using additive manufacturing techniques. Our systems feature designs that enhance fluid dynamics without affecting the stability of the insulin. We propose using Humalog insulin in tropical climates (up to 30°C) without refrigeration for 28 days. The microvalve has a spiral trajectory with four outlet channels distributed along it. These channels align with the microchannels organized in a 10 mm x 15 mm matrix with 25 microchannels, each with a 770 µm internal diameter. The system delivers a dose of 2,3 mL in 6 minutes. We designed these systems for insulin micro-dosing, but they can also serve similar devices for other drugs.

Zn2+ has been implicated in the regulation of intestinal redox and microbial homeostasis, and we recently reported that transient receptor potential canonical (TRPC) 6 channel activity contributes to intracellular Zn2+ homeostasis in mammalian cells. This study aims to investigate the role of TRPC6-mediated Zn2+ influx in stress resistance of intestine. Expression profile of TRPC1-C7 mRNAs in the actively inflamed mucosa from inflammatory bowel disease (IBD) patients was analyzed using GEO database. Systemic TRPC3-knockout (KO) and TRPC6-KO mice were treated with dextran sulphate sodium (DSS) to induce colitis. The Zn2+ concentration and the mRNA expression levels of oxidative/inflammatory markers in colon tissues were quantitatively analyzed, and gut microbiota profiles were compared. TRPC6 mRNA expression level was increased in IBD patients and DSS-treated mouse colon tissues. DSS-treated TRPC6-KO mice, but not TRPC3-KO mice, showed severe weight loss and increased disease activity index compared with DSS-treated WT mice. The mRNA abundances of antioxidant proteins were basically increased in TRPC6-KO colon, with changes in gut microbiota profiles. Treatment with TRPC6 activator prevented the DSS-induced colitis progression accompanied by increasing Zn2+ concentration. We suggest that TRPC6-mediated Zn2+ influx activity plays a key role in stress resistance against IBD, providing a new strategy for treating colitis.

Transient Receptor Potential Vanilloid 4 (TRPV4) channel is a non-selective cation channel, mostly permeable to calcium (Ca2+), which participates to intracellular Ca2+ handling in cardiac cells. It is widely expressed through the body and is activated by a large spectrum of physico-chemical stimuli, conferring it a role in a variety of sensorial and physiological functions. With-in the cardiovascular system, TRPV4 expression was reported in cardiomyocytes, endothelial cells (ECs) and smooth muscle cells (SMCs) where it modulates mitochondrial activity, Ca2+ ho-meostasis, cardiomyocytes electrical activity and contractility, cardiac embryonic development, fibroblast proliferation but also vascular permeability, dilatation and constriction. On the other hand, TRPV4 channels participate in several cardiac pathological processes such as development of cardiac fibrosis, hypertrophy, ischemia-reperfusion injuries, heart failure, myocardial infarc-tion, and arrhythmia. In this manuscript, we provide an overview of TRPV4 channel implica-tions in cardiac physiology and discuss the potential of TRPV4 channel as therapeutic target against cardiovascular diseases.

Next generation in-to-out-of body biomedical applications have adopted optical wireless communications (OWCs). However, by delving into the published literature, a gap is recognised in modeling the in-to-out-of channel, since most published contributions neglect the particularities of different type of tissues. Towards this direction, in this paper we present a novel pathloss and scattering models for in-to-out-of OWC links. Specifically, we derive extract analytical expressions that accurately describe the absorption of the five main tissues’ constituents, namely fat, water, melanin, oxygenated and de-oxygenated blood. Moreover, we formulate a model for the calculation of the absorption coefficient of any generic biological tissue. Next, by incorporating the impact of scattering in the aforementioned model we formulate the complete pathloss model. The developed theoretical framework is verified by means of comparisons between the estimated pathloss and experimental measurements from independent research works. Finally, we illustrate the accuracy of the theoretical framework in estimating the optical properties of any generic tissue based on its constitution. The extracted channel model is capable of boosting the design of optimized communication protocols for a plethora of biomedical applications.

The Casiquiare River is a natural channel that connects two of the greatest rivers in the world, the Orinoco and the Amazon in the South American Continent. The aim of this paper is to present a review and synthesis of the hydrological and sedimentological knowledge of the Casiquiare River, including the first hydro-sedimentary balance of the Casiquiare fluvial system conducted at the bifurcation and at the mouth on September 9-12, 2000, during the expedition ‘Humboldt-Amazonia 2000’. Bathymetric, flow discharge and physico-chemical measurements were made at the inlet and at the outlet of the Casiquiare Channel. The main conclusions of this study indicate that Casiquiare is taking a significant proportion of flow (20 to 30%) from the Upper Orinoco basin to the Amazon basin. Throughout its 356 km-course, this chameleon channel undergoes significant morphological, hydrological and bio-geochemical variations between the inlet and the outlet, whose most visible witnesses are the increase in its width (3 to 4 times), flow (7 to 9 times) and its change in water color (white to black water), under the influence of tributaries coming from vast forest plains.

The purpose of this paper is to propose a novel transfer learning regularization method based on knowledge distillation. Recently, transfer learning methods have been used in various fields. However, the problems such as knowledge loss still occur during the process of transfer learning to a new target dataset. To solve these problems, there are various regularization methods based on knowledge distillation techniques. In this paper, we propose a transfer learning regularization method based on feature map alignment used in the field of knowledge distillation. The proposed method is composed of two attention based submodules: self-pixel attention (SPA) and global channel attention (GCA). The self-pixel attention submodule utilizes both the feature maps of the source and target models, so that it provides an opportunity to jointly consider the features of the target and the knowledge of the source. The global channel attention submodule determines the importance of channels through all layers, unlike the existing methods that calculate these only within a single layer. Accordingly, transfer learning regularization is performed by considering both the internal of each single layer and the depth of the entire layer. Consequently, the proposed method using both of these submodules showed overall improved classification accuracy than the existing methods in classification experiments on commonly used dataset.

This paper addresses the problem of low accuracy of conventional channel estimation and signal detection in complex fields like mines; and the problem of replacing the deep receiver at the receiver side with a deep neural network requires a large amount of data for training and slow training time. Combining the receiver side with traditional communication knowledge, a channel estimation and signal detection method based on the joint ReEsNet and SDRNet under the mine is proposed. The detailed step is to use ReEsNet network for interpolation of conventional channel estimation. Then, on the basis of ReEsNet, the output data is channel equalized and pilots removed, and the previously processed data is input to SDRNet to perform signal recovery. In the complex mine environment, the MSE values are 2e-2 for LS, 6e-3 for MMSE, and 8.44e-5 for ReEsNet at the 1500th sample data for interpolation compared to the conventional channel estimation. the MSE of ReEsNet is the smallest and is closer to the real channel estimation. Compared with the proposed joint channel estimation and signal detection methods, fewer trainable parameters reduce 97% of the parameters compared to CCRNet and 84% of the parameters compared to CNNNet; their detection results, however, are not very different.

KV channel-interacting proteins (KChIPs) belong to a family of Ca2+-binding EF-hand proteins that are able to bind to the N-terminus of the KV4 channel α-subunits. As the auxiliary subunit, KChIPs are critically involved in regulating the amplitude and gating properties of KV4 channels by modulating their cell surface trafficking, voltage-dependent activation, inactivation kinetics, and recovery rate from inactivation. IKs, ICa,L, and INa can also be regulated by KChIPs. KChIPs are predominantly expressed in the brain and heart, where they contribute to the maintenance of the excitability of neurons and cardiomyocytes by modulating the KV4 currents. Interestingly, all KChIPs can act as transcription factors to control the expression of genes involved in pain, memory, and circadian regulation. Altered expression of KChIPs has been implicated in the pathogenesis of many diseases, such as arrhythmia, heart failure, Alzheimer's disease, etc. In this review, we summarize the research progress of KChIPs in their structural properties, physiological functions, and pathological roles in disease progression, and provide an overview of the therapeutic potential of KChIPs as pharmacological targets for associated disorders.

After cut by basecutter, sugarcane stalks are carried to a chopper by the basecutter and the feeding/conveying rollers train of harvester. However, the conventional feeding/conveying channels of sugarcane chopper harvesters, when harvesting seriously lodged sugarcane, have numerous drawbacks, including easy clogging, and poor adaptability. In order to resolve these problems, a novel design and layout method of feeding/conveying and chopping channel are proposed in the paper. And a chopper centrally-mounted channel is designed for a sugarcane chopper harvester as well, which has been implemented in the HN4GDL-91 harvester. The proposed channel consists of a feeding/conveying rollers train, a chopper, and a billet conveying device. By mounting the chopper between the feeding/conveying rollers train and the billets conveying device, the harvester can avoid the chopper chopping back the billets, thus improving the harvest quality. The feeding/conveying rollers train is designed with only a pair of feeding rollers and a pair of conveying rollers, achieving a short channel path. Moreover, the structure of the basecutter and the mechanism carrying stalks to feeding rollers are studied via theoretical analysis and tests. The relationship between the basecutter and the chopper centrally-mounted channel is also conducted in systematic analysis. The results of the theoretical analysis show that the inclination angle of the disc of basecutter should be 2° greater than the angle of the feeding conveying channel (both angles are from the horizontal plane). The inclination angle of the disc of basecutter should go from 10° to 15°. A field experiment with four factors and three levels indicates that the field loss rate is 2.45%, the feed quantity is 16.66 kg/s, and the qualified rate of the billets is 98.02%, while the number of sugarcane stalks in a clump, the ground speed of harvester the rotational speed of the chopper, and the rotational speed of feeding/conveying roller are 10, 1.09 m/s, 390 r/min, and 230 r/min, respectively. It is concluded that the proposed chopper centrally-mounted channel could improve the conveying and harvesting performance significantly.

EMG analysis is becoming increasingly important in many research and clinical applications, including muscle fatigue detection, control of robotic mechanisms and prostheses, clinical diagnosis of neuromuscular diseases and quantification of force. However, electromyographic signals can be contaminated by various types of noise, interference and artifacts, which can lead to misinterpretation of the data acquired using this method. Even assuming best practices, the collected signal may still be altered by such contaminants. The aim of this paper is to review methods employed to reduce contamination of single channel EMG signals. This review is limited to methods performed directly on the measured EMG signal and those that allow total reconstruction of the EMG signal. Subtraction methods used in the time domain, denoising methods performed after signal decomposition and hybrid methods are assessed. It is defended that individual methods may be more or less suitable for a particular application depending on contaminant(s) present in the signal and on the specific requirements of the application.

Deep convolutional neural network (CNN) has shown their great advantages in the single image deraining task. However, most existing CNN-based single image deraining methods still suffer from residual rain streaks and details lost. In this paper, we propose a deep neural network including the Multi-scale feature extraction module and the channel attention module, which are embed in the feature extraction sub-network and the rain removal sub-network respectively. In the feature extraction sub-network, the Multi-scale feature extraction module is constructed by a Multi-layer Laplacian pyramid, and is then integrated multi-scale feature maps by a feature fusion module. In the rain removal sub-network, the channel attention module, which assigns different weights to the different channels, is introduced for preserving image details. Experimental results on visually and quantitatively comparison demonstrate that the proposed method performs favorably against other state-of-the-art approaches

Purpose: The purpose of this study was to evaluate the dosimetric impact of multiple channels compared to a single channel in high dose rate (HDR) vaginal cuff brachytherapy (VCBT). Methods and materials: Sample plans of HDR VCBT from both single and multiple channel cylinders at 2.5, 3.0 and 3.5 cm in diameter were created and analyzed. The doses were prescribed either at the 0.5 cm depth with 5.5 Gy for 4 fractions or at the cylinder surface with 8.8 Gy for 4 frac¬tions, in various treatment lengths ranging from 3 to 8 cm. A 0.5 cm ring target volume called PTV_Eval was contoured for each plan and served as the target volume for dosimetric evaluation. Mean doses and the doses covering 90% (D90), 10% (D10), and 5% (D5) of PTV_Eval were calculated and compared. The same treatment lengths, same prescription regimens, same target volume contouring and same plan evaluation methods were repeated for the similar size single channel and multiple channel cylinders. Results: The mean doses of both regimens with the multi-channel cases (6.3 to 7.1 Gy) were comparable to single channel ones (6.4 and 7.5 Gy). The ranges of D90, D10 and D5 were from 3.654 to 5.04 Gy, 8.44 to 10.08 Gy and 8.84 to 10.86 Gy in the multi-channel cases, but from 5.36 to 5.76 Gy, 7.40 to 9.97 Gy and 8.16 to 11.93 Gy in the single channel cases, respectively. Conclusion: The single channel and multiple-channel cylinder deliver a similar mean dose, but with marked heterogeneity in D90, D5 and D10 for the same prescription dose and target volume. Multi-channel cylinders adequately cover the target volume, but given the heterogeneity, increased treatment time and cost are best suited for asymmetric target volumes.

(1) Background: The Gárdos channel (KCNN4) and Piezo1 are the best-known ion channels in the red blood cell (RBC) membrane. Nevertheless, the quantitative electrophysiological behavior of RBCs and its heterogeneity are still not completely understood.; (2) Methods: Here we use state-of-the-art biochemical methods to probe for the abundance of the channels in RBCs. Furthermore, we utilize automated patch-clamp, based on planar chips, to compare the activity of the two channels in reticulocytes and mature RBCs. Besides this characterization, we performed membrane potential measurements to demonstrate the effect of channel activity and interplay on the RBC properties.; (3) Results: Both, Gárdos channel and Piezo1, albeit their average copy number of activatable channels per cell is in the single digit range, can be detected by transcriptome analysis of reticulocytes. Proteomics analysis of RBCs could only detect Piezo1 but not the Gárdos channel. Furthermore, they can be reliably measured in the whole-cell configuration of the patch-clamp method. While for the Gárdos channel the activity is higher in reticulocytes compared to mature RBCs, for Piezo1 the tendency is the opposite. While the interplay between Piezo1 and Gárdos channel cannot be followed using the patch-clamp measurements, it could be proved based on membrane potential measurements in populations of intact RBCs.; (4) Conclusions: We discuss the Gárdos channel and Piezo1 abundance, interdependencies and interactions in the context of their proposed physiological and pathophysiological functions, which are the passing of small constrictions, e.g., in the spleen, and their active participation in blood clot formation and thrombosis.

Data obtained by Direct Numerical Simulations (DNS) of pressure-driven turbulent channel flow are studied in the range 180 ≤ Reτ≤ 10,000. Reynolds number effects on the Mean Velocity Profile (MVP) and second order statistics are analyzed with a view of finding logarithmic behavior in the overlap region or even further from the wall, well in the boundary layer’s outer region. Values of Kármán constant for the MVPs and the Townsend-Perry constants for the streamwise and spanwise fluctuation variances are determined for the Reynolds numbers considered. A data-driven model of the MVP, proposed and validated for zero pressure gradient flow over a flat plate, is employed for pressure-driven channel flow by appropriately adjusting Coles’ strength of the wake function parameter, Π. There is excellent agreement between the analytic model predictions of MVP and the DNS-computed MVP as well as of the Reynolds shear stress profile. The skin friction coefficient Cf is calculated analytically. The agreement between the analytical model predictions and the DNS-based computed discrete values of Cf is excellent.

Our study provides guidelines on how to build long-term customer relationship in the non-contract mechanism context. More specifically, the findings show that special, social, and core benefits influence calculative commitment, and operational and special benefits influence affective commitment. This study also supports that calculative and affective commitment play a crucial role in understanding multi-channel agencies’ loyalty. In sum, this study revealed that calculative and affective commitment can be considered as partial or full mediators in the relationship between RBs (relational benefits) and loyalty. This study not only contributed to the existing SET (social exchange theory) and RBs paradigm but also provided practical implications for food distribution management.

Microcombs provide a potential compact and efficient light source for multi-Terabit-per-second optical superchannels. However, as the bandwidth of these multi-wavelength light sources is increased, this can result in low per-line power. Optical amplifiers can be used to overcome power limitations, but the accompanying spontaneous optical noise can degrade performance in optical systems. To overcome this issue, we propose wideband noise reduction for comb lines using a high-Q microring resonator, whose resonances align with comb lines. When applying the proposed distillation to a superchannel system with 18 Gbaud, 64-QAM sub-channels in a > 10 Tb/s optical superchannel, we find that noise-corrupted comb lines can reduce the optical signal-to-noise ratio required for the comb by ~ 9 dB when used as optical carriers at the transmitter side, and by ~ 12 dB when used as a local oscillator at the receiver side.

In this paper, we investigate the “statics and dynamics” return and volatility spillovers transmission across developed and developing countries. Quoted against the U.S. dollar, we study twenty-three global currencies over 2005 – 2016. Focusing on the spillover index methodology, the generalised VAR framework is employed. Our findings indicate no evidence of bi-directional return and volatility spillovers between developed and developing countries. However, a unidirectional volatility spillover from developed to developing countries is highlighted. Furthermore, our findings document significant bi-directional volatility spillovers within the European region (Eurozone and non-Eurozone currencies) with the British Pound (GBP) and the Euro (EUR) as the most significant transmitters of volatility. The findings reiterate the prominence of volatility spillovers to financial regulators.

As e-commerce services and Internet technology have rapidly developed in recent years, many services and applications integrating these technologies can now be completed online. These commercial activities include online auctions, online ticketing and online payments. The client shops from the store online, andthe store delivers the goods to the client. The goods can be divided into digital products without entities, as well as actual entities. If it is a physical product, the store will deliver the package to the client through itslogistics. However, there have been many cases of switched goods purchased by clients in recent years. Earlier, some scholars proposed a security mechanism with a subliminal channel for E-cash and digital content. Only the sender and the receiver would know that the secret information was hidden in the signature. So the privacy of this subliminal message couldbe ensured. We apply this concept to the logistics environment to design secure logistics architecture with subliminal messages. The client can check the subliminal message of the received package, and know whether the package has been switched by malicious people. In addition, the proposed scheme also applies sensor technology;the client can check the GPS location, the temperature and humidity at any time during the delivery process. So intelligent logisticswouldthereby be achieved. This paper proposes an intelligent and secure package sensoring logistics system based on a subliminal channel. The proposed architecture uses the related mechanisms tosolve the problems of a logistics system, including how to achieve mutual authentication, data integrity, anti-switch package, package location and status tracing, resisting replay attacks, forward and backward secrecy, and non-repudiation issues.

The segmentation and de-noising are basic operations, required in every signal processing and classification system. The classical segmentation and de-noising approaches are time-invariant. Consequently, it results in the post processing of an unnecessary information and causes an increase in the system processing activity and power consumption. In this context, an efficient event-driven segmentation and de-noising technique is proposed. It is founded on the principles of level crossing and activity selection. Therefore, it can adapt its sampling frequency, segmentation window length and position along with the filter order by analyzing the input signal local characteristics. As a result, the computational complexity and the power consumption of the proposed system is reduced compared to the counter ones. The suggested system performance is compared with the classical one. It is done for the case of a multi-channel Electroencephalogram (EEG) signals. Results show a noticeable compression gain with an effective adaptation of the de-noising filters order. It aptitudes a significant computational gain, transmission data rate reduction and power consumption reduction of the proposed technique, compared to the counter ones. It shows that the proposed solution is an attractive candidate to embed in the new generation EEG wearables.

This paper presents the design and implementation of a multichannel bio-impedance spectroscopy system on field programmable gate arrays (FPGA). The proposed system is capable of acquiring multiple signals from multiple bio-impedance sensors, process the data on the FPGA and store the final data in the on-board Memory. The system employs the Digital Automatic Balance Bridge (DABB) method to acquire data from biosensors. The DABB measures initial data of a known impedance to extrapolate the value of the impedance for the device under test. This method offers a simpler design because the balancing of the circuit is done digitally in the FPGA rather than using an external circuit. Calculations of the impedance values for the device under test were done in the processor. The final data is sent to an onboard Flash Memory to be stored for later access. The control unit handles the interfacing and the scheduling between these different modules (Processor, Flash Memory) as well as interfacing to multiple Balance Bridge and multiple biosensors. The system has been simulated successfully and has comparable performance to other FPGA based solutions. The system has a robust design that is capable of handling and interfacing input from multiple biosensors. Data processing and storage is also performed with minimal resources on the FPGA.

Recently, deep learning models have been widely applied to modulation recognition, which have become a hot topic due to their excellent end-to-end learning capabilities. However, current methods are mostly based on uni-modal inputs, which suffer from incomplete information and local optimization. To complement the advantages of different modalities, we focus on the multi-modal fusion method. Therefore, we introduce an iterative dual-scale attentional fusion (iDAF) method to integrate multimodal data. Firstly, two feature maps with different receptive field sizes are constructed using local and global embedding layers. Secondly, the feature inputs are iterated into the Iterative Dual Scale Attention Module (iDCAM), where the two branches capture the details of high-level features and the global weights of each modal channel, respectively. The iDAF not only extracts the recognition characteristics of each specific domains, but also complements the strengths of different modalities to obtain a fruitful view. Our iDAF achieves a recognition accuracy of 93.5\% at 10dB and 0.6232 at full SNR. The comparative experiments and ablation studies effectively demonstrate the effectiveness and superiority of the iDAF.

This paper presented a two-dimensional, well-balanced hydrodynamic and sediment transport model based on the solutions of variable density shallow water equations (VDSWEs) for sediment-laden flows, and the Exner equation for bed changes. Those equations are solved in a coupled way by the first-order Godunov-type finite volume method. The Harten-Lax-van Leer-Contact (HLLC) Riemann solver is extended to find the local Riemann fluxes in order to maintain the exact balance between the momentum term and the bed slope term. The advantage of a well-balanced scheme over an unbalanced scheme is demonstrated by the synthetic standing contact-discontinuity test case. Then, the model is employed to simulate two laboratory experiments. At last, a field case, the 1996 Lake Ha! Ha! flood event (Canada), is simulated. Results of cross sectional geometries and profiles of longitudinal thalweg agree well with measurements. The accuracy and simplicity of the numerical model, together with the robust implementation, make the model a good candidate for practical engineering applications.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton communities but is biased towards those organisms that can be distinguished using the microscope. Genetic identification of marine plankton has become standard but is still not used. This study is a comprehensive study genetically measured taxa in the Western Channel of UK using a small-volume automated water sampler deployed on the CPR platform. The study present one year of high-throughput sequencing data focussing on smaller plankton and separate community to that measured by microscopy that can complement each other for a holistic view of plankton. Quantitative tests of two harmful algae show relatively high abundance of the Pelagophyte Aureococcus anophagefferens during 2011 with low nitrite levels. Three years of Pseudo-nitzschia delicatissima quantitative monitoring also shows a greater abundance of this potentially harmful taxa in 2011. Flow cytometry reveals distinct seasonal cycles with distinct timings.

To realize precise control of the quantum dots (Qdots) device, multi-channel precision bias source plays the key role. In this paper, the 16-channel high precision bias source with 18-bit resolution for Qdots device was designed. The prototype was made and its performance was tested. The short time fluctuations can reach 50μV. The step response time is less than 3μs. The resolution, stability, linearity and dynamic range of the bias source exhibits good performance. What's more, the bias source can be controlled locally and online. The results show that it is one effective and feasible topology for experiments in Qdots device application.

Flood routing in flood forecasting issue, calculation the height of flood bands, determining the river boundaries, and estimation of protective facilities for flood –exposed building is applicable. In many cases, due to the lack of measuring stations, the status of the upstream flood generating hydrograph is not known. The purpose of this study is to present an integrated method comprising of an optimization model and a hydrodynamic numerical model for flood modeling to determine the upstream hydrograph using the provided hydrograph at the downstream measuring station of a river. The routing procedure consists of three steps: (1) generating a hypothetical upstream hydrograph using genetic algorithm method; (2) hydrodynamic modeling using a numerical simulation model for flood routing according to the hypothetical hydrograph which is generated in the first step; (3) compare the calculated and observed hydrograph in downstream by using a fitness function. This recommended procedure was named as Reverse Flood Routing Method (RFRM) and was then applied to Karun River, the largest river in Iran. Comparing the generated upstream hydrograph by the RFRM model with the corresponding measured hydrograph at Ahvaz hydrometric station, as an ungauged river location, shows the high accuracy of the recommended model in this study.

This paper proposes the use of compressive sensing to tackle the Massive MIMO channel estimation problem. As our results show compressive sensing-based estimators perform as well as the optimum MMSE estimator.

In this paper, spatial pulse position modulation (SPPM) is used as a case study to investigate the performance of the optical spatial modulation (SM) technique in outdoor atmospheric turbulence (AT). A closed-form expression for the upper bound on the asymptotic symbol error rate (SER) of SPPM in AT is derived and validated by closely-matching simulation results. The error performance is evaluated in weak to strong AT conditions. As the AT strength increases from the weak to strong, the channel fading coefficients become more dispersed and differentiable. Thus, a better error performance is observed under moderate-to-strong AT compared to weak AT. The performance in weak AT can be improved by applying unequal power allocation to make FSO links more distinguishable at the receiver. Receive diversity is considered to mitigate irradiance fluctuation and improve the robustness of the system to turbulence-induced channel fading. The diversity order is computed as half of the number of detectors. Performance comparisons, in terms of energy and spectral efficiencies, are drawn between the SPPM scheme and conventional MIMO schemes such as repetition coding and spatial multiplexing.

This study investigates the electrical characteristics observed in n- channel and p-channel ferroelectric field effect transistor (FeFET) devices fabricated through a similar process flow with 10 nm of ferroelectric hafnium zirconium oxide (HZO) as the gate dielectric. The n-FeFETs demonstrate a faster complete polarization switching compared to the p-channel counterparts. Detailed and systematic investigations using TCAD simulations reveal the role of fixed charges and interface traps at the HZO-interfacial layer (HZO/IL) interface in modulating the subthreshold characteristics of the devices. A characteristic crossover point observed in the transfer characteristics of n-channel devices is attributed with the temporary switching between ferroelectric-based operation to charge-based operation, caused by the pinning effect due to the presence of different traps. This experimental study helps understand the role of charge trapping effects in switching characteristics of n- and p-channel ferroelectric FETs.

The combination of e-commerce and the green economy allows enterprises to distribute their green products directly to consumers through Internet channels. This paper investigates the impact of service spillovers on emission reduction and channel decisions in a two-echelon supply chain,in which the supplier is a Stackelberg leader and the retailer is a follower.By comparing the equilibrium outcomes of the single-channel and dual-channel supply chain in a setting with and without retail services, we observe that the supplier prefers to encroach on the market when services that retail locations provide largely spillover to and benefit the direct sales channel. Contrary to popular belief, a higher degree of service spillovers is beneficial for the retailer to get more returns under the dual-channel structure, whereas supplier encroachment will lead to a decline in the service level if the spillover degree is relatively low. In addition, the emission reduction level of products under supplier encroachment is always higher than that employed in the single-channel structure if consumers have both low-carbon preference and high degree of service sensitivity. Furthermore, we extend the equilibrium decisions under a carbon cap-and-trade (CCT) mechanism; the results fully verify the above conclusions. Interestingly, the implementation of a carbon price not only motivates carbon emission abatement and supplier encroachment, but also helps achieve a win-win outcome for supply chain members when service spillovers happen.

Nowadays, considering the growing tendency of companies towards e-commerce as well as green production, and dual-channel green supply chain management has become particularly important. This paper investigates pricing decisions within a dual-channel green supply chain framework while considering the capital constraints faced by risk-averse manufacturer. Simultaneously, the impact of the degree of risk aversion, consumer green preferences, and channel preferences on the optimal decision-making process of green supply chain members is analyzed. We address the issue of financial constraints faced by manufacturer through bank loans and trade credit financing and compare the two cases. Our findings illustrate that trade credit financing outperforms bank loan financing in the dual-channel green supply chain. Moreover, pricing decisions under different models are influenced by consumer preferences and risk aversion. Specifically, the greenness of the product, wholesale price, and sale price exhibit negative correlations with manufacturers' risk aversion but positive correlations with consumer preferences.

Unidirectional flow of a fluid with pressure-dependent viscosity through a porous structure is considered when the viscosity-pressure relationship is an exponential function of a pressure power function in order to investigate effects of the viscosity-pressure relation on the flow characteristics. The flow is governed by the generalized Brinkman’s equation with constant permeability, and a model flow domain of flow down an inclined porous channel is chosen for the sake of studying flow behaviour. Although the current work considers flow in a constant permeability porous structure, it does represent a first step in studying the more general, flow through a variable permeability porous channel. The arising governing equations are solved numerically using MATLAB and the flow is simulated to illustrate the effects of fluid properties as well as flow and medium parameters on the velocity profiles and shear stress.

Emerging evidence indicates that intracellular calcium (Ca2+) levels and their regulatory proteins play essential roles in normal stem cell proliferation and differentiation. Cancer stem-like cells (CSCs) are subpopulations of cancer cells that retain characteristics similar to stem cells and play an essential role in cancer progression. Recent studies have reported that the Orai3 calcium channel plays an oncogenic role in human cancer. However, its role in CSC remains underexplored. In this study, we explored the effects of Orai3 in the progression and stemness of oral/oropharyngeal squamous cell carcinoma (OSCC). Orai3 expression was increased in a stepwise manner during the progression of OSCC. In addition, Orai3 was highly enriched in CSC populations of OSCC. Ectopic Orai3 expression in non-tumorigenic immortalized oral epithelial cells increased intracellular Ca2+ levels, acquiring malignant growth and CSC properties. Conversely, silencing of endogenous Orai3 in OSCC cells suppressed CSC phenotype, indicating a pivotal role of Orai3 in CSC regulation. Moreover, Orai3 markedly increased the expression of inhibitor of DNA binding 1 (ID1), a stemness transcription factor. Orai3 and ID1 were highly expressed in CSCs compared to non-CSCs, implying the functional importance of the Orai3/ID1 axis in CSC regulation. Furthermore, suppression of ID1 abrogated CSC phenotype in the cell with ectopic Orai3 overexpression and OSCC. Our study reveals that Orai3 is a novel functional CSC regulator in OSCC and further suggests that Orai3 plays an oncogenic role in OSCC by promoting cancer stemness via ID1 upregulation.

A micro energy harvesting device proposed in the literature, is numerically studied. It consists of two bluff bodies in a micro-channel and a flexible diaphragm at its upper wall. Vortex shedding behind bodies induces pressure fluctuation causing vibration of the diaphragm that converts me-chanical energy to electrical by means of a piezoelectric membrane. Research on enhancing vortex shedding is justified due to the low power output of the device. Amplitude and frequency of un-steady pressure fluctuation on the diaphragm center are numerically predicted. Vortex shedding severity is mainly assessed in terms of pressure amplitude. The CFD model set-up is described in detail and appropriate metrics to assess energy harvesting potential are defined. Several cases are simulated to study the effect of inlet Reynolds number and channel blockage ratio on the prospec-tive performance of the device. Furthermore, the critical blockage ratio leading to vortex shedding suppression is sought. Higher inlet velocity for a constant blockage ratio is found to enhance vor-tex shedding and pressure drop. Great blockage ratio values, but lower than the critical one, seem to provide great pressure amplitudes in the expense of moderate pressure drop. There is evidence that the field is fruitful for research and relevant directions are provided.

Channel estimation is an important module to enhance the performance of orthogonal frequency division multiplexing (OFDM) systems. However, the presence of a large amount of noise in multipath fading time-varying channels significantly affects the channel estimation accuracy and thus the recovery quality of the received signals. Therefore, this paper proposes a double-threshold (DT) channel estimation method based on adaptive frame statistics (AFS). The method first adaptively determines the number of statistical frames based on the temporal correlation of the received signals, and preliminarily detects the channel structure by analyzing the distribution characteristics of multipath sampling points and noise sampling points during adjacent frames. Subsequently, a multi-frame averaging technique is used to expand the distinction between multipath and noise sampling points. Finally, the DT is designed to better recover the channel based on the preliminary detection results. Simulation results show that the proposed adaptive frame statistics-double-threshold (AFS-DT) channel estimation method is effective and has better performance compared with many existing channel estimation methods.

The process of water treatment by nanoparticles is one of the most considerable subjects in the cross-field of hydrodynamics, chemistry and mathematics. This paper is dedicated to the case of the flows that appear when squeezing and stretching a spongy with a mix of water with nanoparticles and contaminants. It is assumed that fluid is homogeneous at the starting moment, the parameters of the nanoparticles and contaminants are known, and there is a constant non-homogeneous magnetic field applied to the system. The flow starts moving when the walls of the channel shift to each other. Exact and numerical solutions of the system of ordinary differential equations are used to receive the results. The article gives an answer to the question about stability of the flow and proposes the technique to evaluate the essential characteristics of the system to achieve the treatment process efficiency. The main result is that the considered system shows excellent treatment properties during some part of squeezing stage. This effect does not appear without magnetic field.

Crowd counting is of significant importance for numerous applications, e.g., urban security, intelligent surveillance and crowd management. Existing crowd counting methods typically require specialized hardware deployment and strict operating conditions, thereby hindering their widespread deployment. To acquire a more effective crowd counting approach, a device-free counting method based on Channel Status Information (CSI) is proposed, which could mitigate environment noise through wavelet transform and extract the amplitude or phase covariance matrix as the feature vector. Moreover, both the spatial diversity and frequency diversity are leveraged to improve detection robustness. The accuracy of the proposed CSI-based method is compared with a renowned crowd counting one, i.e., Electronic Frog Eye: Counting Crowd Using WiFi (FCC). The experimental results reveal an accuracy improvement of 30% over FCC.

The enzyme-coupled transient receptor potential channel subfamily M member 7, TRPM7, has been associated with immunity and immune cell signalling. Here, we review the role of this remarkable signalling protein in lymphocyte proliferation, differentiation, activation and survival. We also discuss its role in mast cell, neutrophil and macrophage function and highlight the potential of TRPM7 to regulate immune system homeostasis. Further, we shed light on how the cellular signalling cascades involving TRPM7 channel and/or kinase activity culminate in pathologies as diverse as allergic hypersensitivity, arterial thrombosis, and graft versus host disease (GVHD), stressing the need for TRPM7 specific pharmacological modulators.

This paper considers a hybrid relay network consisting of the source, the amplify-and-forward (AF) relay, the decode-and-forward (DF) relay, and the destination. We propose the optimal power allocation schemes between two different relays which maximize the achievable rate under a sum relay power constraint for given channel gains and transmit power from source. By solving the optimization problem to maximize the achievable rate for each relay network, the transmit power values in closed-form are derived. When the channel gains are the same, the optimal power allocation scheme for AF-DF relay network proves that a more power should be allocated at the first relay to maximize the achievable rate. In case of the DF-AF relay network, we derive the optimal power allocation scheme for the possible four cases. Under the same SNR condition at the first hop, we show that the achievable rate of AF-DF relay network is greater than that of DF-AF relay network when the channel gain between two relays is higher than that between the second relay and destination. Simulation results show that the proposed power allocation schemes provide a higher achievable rate than the equal power allocation schemes.

Analytical channel design tools have not advanced appreciably in the last decades, and continue to produce designs based upon a single representative discharge that may not lead to overall sediment continuity. It is beneficial for designers to know when a simplified design may be problematic and to efficiently produce alternative designs that approximate sediment balance over the entire flow regime. The Capacity/Supply Ratio (CSR) approach, an extension of the Copeland method of analytical channel design for sand channels, balances the sediment transport capacity of a design reach with the sediment supply of a stable upstream reach over the entire flow duration curve (FDC) rather than just a single discharge. Although CSR has a stronger physical basis than previous analytical channel design approaches, it has not been adopted in practice because it can be a cumbersome and time-consuming iterative analysis without the use of software. We investigate eighteen sand-bed rivers in a comparison of designs based on the CSR approach and five single-discharge metrics: the effective discharge (Qeff), the 1.5-year recurrence interval discharge (Q1.5), the bankfull discharge (Qbf), and the discharges associated with 50th (Qs50) and 75th (Qs75) percentiles of the cumulative sediment yield curve. To facilitate this analysis we developed a novel design tool using the Visual Basic for Applications (VBA) programming language in Excel® to produce stable channel slope-width combinations based on the CSR methodology for both sand- and gravel-bed streams. The CSR Stable Channel Design Tool’s (CSR Tool) code structure was based on Copeland’s method in SAM and HEC-RAS (Hydrologic Engineering Center’s River Analysis System) and was tested with a single discharge to verify outputs. The Qs50 and Qs75 single-discharge designs match the CSR output most closely, followed by the Qbf, Qeff, and Q1.5. The Qeff proved to be the most inconsistent design metric because it can be highly dependent on the binning procedure used in the effectiveness analysis. Furthermore, we found that the more rigorous physical basis of the CSR analysis is potentially most important in designing ‘labile’ channels with highly erodible substrate, high perennial flow ‘flashiness,’ low width-to-depth ratio, and high incoming sediment load. The CSR Tool provides a resource for river restoration practitioners to efficiently utilize in-depth design techniques that can promote sediment balance in dynamic fluvial systems.

In airborne sensor networks (ASNs), the media access control (MAC) protocol is facing with serious unfairness problem due to the traditional protection mechanism of air-to-air communications among aircrafts. Actually by using the binary exponential back-off algorithm at high traffic loads to minimize collisions among users, the latest successful node can always benefit from this kind of MAC to obtain channel resources. Moreover, when taking the existence of the hidden nodes in ASNs into account, the inaccurate traffic load information will further aggravate the system’s unfairness. In this paper, a neighbor-channel-aware (NCA) protocol is proposed to improve the fairness of MAC protocol in ASNs. In the proposal, the NCA frame is firstly added and exchanged between neighbor nodes periodically, which helps to resolve the inaccurate traffic load information, so as to avoid reducing the probability of successful message transmission. Then a traffic-loading based back-off algorithm is involved to make the neighbor nodes cooperatively adjust the inter-frame space (IFS) interval to further reduce the unfairness. The simulation results show that, the proposed MAC protocol can guarantee the satisfied fairness, simultaneously avoiding heavy network overloads to protect key messages’ successful transmissions in ASNs.

This work addresses the challenge of EEG visual multiclass classification into 40 classes for Brain-Computer interface applications, by using deep learning architectures. The visual multiclass classification approach offers BCI applications a significant advantage, since it allows the supervision of more than one BCI interaction, considering that each class label supervises a BCI task. However, because of the nonlinearity and nonstationarity of EEG signals, performing multiclassifiers based on EEG features remains a significant challenge for BCI systems. In the present work, mutual information-based discriminant channel selection and Minimum-Norm Estimate algorithms are implemented to select discriminant channels and enhance EEG data. Hence, deep EEGNet and Convolutional-recurrent neural networks are implemented separately to classify EEG data of image visualization into 40 labels. By using the k-fold cross-validation approach, average classification accuracies of 94.8% and 89.8% were obtained by implementing the aforementioned network architectures, respectively. Satisfactory results obtained with this method offer a new implementation opportunity for multi-task BCI applications by utilizing a reduced number of channels (<50%), compared to those presented in the related literature where the whole set of channels is used.

Terahertz tomography is a promising method among non-destructive inspection techniques to detect faults and defects in dielectric samples. Image quality recently significantly improved through the incorporation of a priori information and off-axis data. However, this improvement has come at the cost of increased measurement time. To aim toward industrial applications, it is therefore necessary to speed up the measurement by parallelizing the data acquisition employing multi-channel setups. In this work, we present two tomographic frequency-modulated continuous wave (FMCW) systems working at a bandwidth of 230-320 GHz, equipped with an eight-channel detector array, and compare their imaging results with a single-pixel setup. While in the first system, the additional channels are used exclusively to detect radiation refracted by the sample, the second system features an f-θ lens, focusing the beam at different positions on its flat focal plane, and thus utilizing the whole detector array directly. The usage of the f-θ lens in combination with a scanning mirror eliminates the necessity of the formerly used slow translation of a single-pixel transmitter. This opens up the potential for a significant increase in acquisition speed, in our case by a factor of four to five, respectively.

The Cav3.2 T-type calcium channel is implicated in various pathological conditions, including cardiac hypertrophy, epilepsy, autism, and chronic pain. Phosphorylation of Cav3.2 by multiple kinases plays a pivotal role in regulating its calcium channel function. The calcium/calmodulin-dependent serine/threonine phosphatase, calcineurin, interacts physically with Cav3.2 and modulates its activity. However, it remains unclear whether calcineurin dephosphorylates Cav3.2, the specific spatial regions on Cav3.2 involved, and the extent of the quantitative impact. In this study, we elucidated the serine/threonine residues on Cav3.2 targeted by calcineurin using quantitative mass spectrometry. We identified six serine residues in the N-terminus, II-III loop, and C-terminus of Cav3.2 that were dephosphorylated by calcineurin. Notably, a higher level of dephosphorylation was observed in the Cav3.2 C-terminus, where calcineurin binds to this channel. Additionally, a previously known CaMKII-phosphorylated site, S1198, was found to be dephosphorylated by calcineurin. Furthermore, we also discovered that a novel CaMKII-phosphorylated site, S2137, underwent dephosphorylation by calcineurin. In CAD cells, a mouse central nervous system cell line, membrane depolarization led to an increase in the phosphorylation of endogenous Cav3.2 at S2137. Mutation of S2137 affected the calcium channel function of Cav3.2. Our findings advance the understanding of Cav3.2 regulation not only through kinase phosphorylation but also via calcineurin phosphatase dephosphorylation.

Compressed Sensing (CS) MRI has shown great potential in enhancing time efficiency. Deep learning techniques, specifically Generative Adversarial Networks (GANs), have emerged as potent tools for speedy CS-MRI reconstruction. Yet, as the complexity of deep learning recon-struction models increases, this can lead to prolonged reconstruction time and challenges in achieving convergence. In this study we present a novel GAN-based model that delivers superior performance without escalating model complexity. Our generator module, built on the U-net architecture, incorporates dilated residual (DR) networks, thus expanding the network's receptive field without increasing parameters or computational load. At every step of the downsampling path, this revamped generator module includes a DR network, with the dilation rates adjusted according to the depth of the network layer. Moreover, we have introduced a channel attention mechanism (CAM) to distinguish between channels and reduce background noise, thereby fo-cusing on key information. This mechanism adeptly combines global maximum and average pooling approaches to refine channel attention. We conducted comprehensive experiments with the designed model using public domain MRI datasets of the human brain. Ablation studies af-firmed the efficacy of the modified modules within the network. Compared to other relevant models, our proposed model exhibits exceptional performance, achieving not only excellent sta-bility but also outperforming other networks in terms of Peak Signal-to-Noise Ratio (PSNR) and Structural Similarity Index (SSIM). The model presents a promising pathway for enhancing the efficiency and quality of CS-MRI reconstruction.

Wireless communications are gaining massive demand for faster video streaming, virtual reality, and 5G-based IoT (Internet of Things) applications. Due to this network congestion increases hastily. The demand for user-specific services, machine learning, forcing the radio access network (RAN) to provide improvement in utilization of spectrum efficiency, minimizing power consumption, and improving data rate. For LTE/LTE-A network specifications provided by third-generation partnership project (3GPP), guarantees to provide qualitative of service (QoS). Release 15/16 utilizes two-dimensional (2D) active antenna array systems (AAS). This kind of AAS provides beam forming in both azimuth and elevation also termed as Full Dimensional MIMO (FD-MIMO). It enhances the radiation pattern of the antenna array element by adjusting the angular power spectra at the base station (BS), it also allows selecting the minimum number of antennas for effective beam forming toward specific user equipment’s (UEs). Spectrum allocation challenge can be dealt with at mm wave band having FR2 (>6GHz) frequency band specified by International Telecommunication Union (ITU-R) in line with IMT-2020 specifications. The spectrum is free at mm Wave for communication of 5G. However, the main challenge is, it faces path loss and atmospheric loss electromagnetic energy absorbed by gases like oxygen. In this work, the 5G new RAN power spectrum and power delay profile at 10GHz carrier frequency with 20MHz to 100MHz channel bandwidth is observed for line of sight (LOS) and non-line of sight (NLOS) communication for guaranteed QoS. To demonstrate the path loss and power delay profile (PDP) in directional and Omni-directional antennas NYUSIM channel simulator is utilized.

Mouse models of alcohol use disorder (AUD) revealed a subtype of purinergic receptors (P2X4Rs) as a promising target for AUD drug development. We have previously demonstrated that residues at the transmembrane (TM)-ectodomain interface and within TM1 segment contribute to the formation of an ethanol action pocket in P2X4Rs. In the present study, we tested the hypothesis that there are more residues in TM segments, which are important for ethanol sensitivity of P2X4Rs. Using site-directed mutagenesis and two-electrode voltage-clamp electrophysiology in Xenopus oocytes, we found that arginine at position 33 (R33) in the TM1 segment plays a role in ethanol sensitivity of P2X4Rs. Molecular models in both closed and open states provided evidence for interactions between R33 and aspartic acid at position 354 (D354) of the neighboring TM2 segment. Further work with mixtures of wild-type (WT) and reciprocal single (R33D:WT, D354R:WT) and double (R33D-D354R:WT) mutants confirmed the importance of this interaction for ethanol sensitivity, ivermectin action and channel function. Additionally, our findings suggest that valine at TM1 position 49 plays a role in P2X4R function by providing flexibility during channel opening. Collectively, these findings identified new activity sites, and suggest the importance of TM1-TM2 interaction for channel function and ethanol sensitivity of P2X4Rs.

The possibility to test a radio frequency transceiver through the use of appropriate channel emulators allows to evaluate their performance under various operating conditions. Many systems are able to operate with a relatively limited instantaneous bandwidth by applying known statistical models. Sometimes it is necessary to evaluate the performance of a RF transceiver installed on high or very high speed platforms over predictable trajectories using optionally DEMs (Digital Elevation Models)data of the terrain to estimate the number of stimulated paths and their contributions during the flight. When the instantaneous bandwidth of the signal becomes high (over several hundred of MHz), one of the most important phenomenon to consider is the Doppler spread induced by the channel and traditional narrowband models become unuseful. In this paper there are presented some results when a time expansion is adopted in order to emulate the transceiver dynamic and the consequent Doppler spread with the aim to control the spectral purity of the emulated propagation channel.

Enhancement in the strength of austenitic steels with a small content of carbon can be achieved by a limited number of methods, among which is the ultrafine-grained (UFG) structure formation, especially efficient with the use of severe plastic deformation (SPD) processing that enables increasing significantly the contribution of grain-boundary strengthening, and also involves a combination of other strengthening factors (work hardening, twins, etc.). In this paper, we demonstrate that the use of SPD processing combined with conventional methods of deformation treatment of metals, such as rolling, may lead to an additional strengthening of UFG steel. Analysis of the results of the study on the change of the microstructure and mechanical properties of the Cr-Ni stainless austenitic steel after a combined deformation reveals a substantial increase in the strength properties of this steel, resulting from a consecutive application of SPD processing via equal-channel angular pressing and rolling at a temperature of 400 С, yielding a strength more than 1.5 times higher that that produced by any of these two methods used separately.

Recently, attention mechanisms have developed into an important tool for performance improvement of deep neural networks. In computer vision, attention mechanisms are generally divided into two main branches: spatial and channel attention. Both attention categories have their own advantages. The fusion of both attentions achieves higher performance, on the cost of the computational load. This paper introduces an innovative and lighter n-shifted sigmoid channel and spatial attention (CSA) module to reduce the computational cost and to improve the 3D scene relevant features selection. To validate the proposed attention module, 3D scene object detection in the deep Hough voting point sets is considered as the testing application. The proposed attention module with its piecewise n-shifted sigmoid activation function improves the network’s learning and generalization capacity which effectively predict bounding box parameters directly from 3D scenes and detect objects more accurately. This advantage is achieved by selectively attending to more relevant features of the input data. When used in the deep Hough voting point sets, the proposed attention module outperforms state-of-the-art 3D detection methods on the sizable SUNRGBD dataset. Experiments conducted showed an increase of 12.02 mean accuracy precision (mAP) when compared to the celebrated VoteNet (without attention). It also got 9.92 mAP higher compared to the MLVCNet, and 10.32 mAP higher than the Point Transformer. The proposed model not only decreases the sigmoid vanishing gradient problem but also brings out valuable features by fusing channel-wise and spatial information while improving accuracy results in 3D object detection.

Deep learning methods have been widely used in PolSAR image classification. To learn the polarimetric information, many deep learning methods expect to learn high-level semantic features from original PolSAR data. However, only original data cannot learn multiple scattering features and complex structures for extremely heterogeneous terrain objects. In addition, deep learning methods always cause edge confusion due to the high-level features. To overcome these shortages, we propose a double-channel CNN network combined with an edge-preserving MRF model(DCCNN-MRF) for PolSAR image classification. Firstly, to combine complex matrix data and multiple scattering features together, a double-channel convolution network(DCCNN) is developed, which consists of a Wishart-based complex matrix and multi-feature subnetworks. The Wishart-based complex matrix network can learn the statistical characteristics and channel correlation well, and the multi-feature network can learn high-level semantic features well. Then, a unified network framework is designed to fuse two kinds of features to enhance advantageous features and reduce redundant ones. Finally, an edge preserving MRF model is designed to combine with the DCCNN network. In the MRF model, a sketch map-based edge energy function is designed by defining adaptive weighted neighborhood for edge pixels. Experiments are conducted on four real PolSAR data sets with different sensors and bands. Experimental results demonstrate the effectiveness of the proposed DCCNN-MRF method.

The current neural networks for tomato leaf disease recognition have problems such as large model parameters, long training time, and low model accuracy. To solve these problems, a lightweight convolutional neural network LBFNet is proposed in this paper.First, a lightweight convolutional neural network LBFNet is established as the base model. Secondly, a three-channel attention mechanism module is introduced to learn the disease features in tomato leaf disease images and reduce the interference of redundant features. Finally, a cascade module is introduced to increase the depth of the model, solve the gradient descent problem, and reduce the loss caused by increasing the depth of the model. The quantized pruning technique is also used to further compress the model parameters and optimize the model performance. The results show that the LBFNet model achieves 99.06% accuracy on the LBFtomato dataset, with a training time of 996s and a single classification accuracy of over 94%. Further training using the saved weight file after quantized pruning makes the model accuracy reach 97.66%. Compared with the base model, the model accuracy was improved by 28%, and the model parameters were reduced by 96.7% compared with the traditional Resnet50. It was found that LBFNet can quickly and accurately identify tomato leaf diseases in complex environments, providing effective assistance to agricultural producers.

We are introducing a highly efficient 48-channel ultrasound beamforming system ideal for ultrasound endoscopy applications. The system includes a transmitter and a receiver, which allow for low-area, high-resolution imaging acquisition. The transmitter uses a charge redistribution HV (high voltage) scheme to generate three-level pulses that actuate the transducer, implemented with the standard CMOS process for optimal cost and power savings. Meanwhile, the receiver features a sub-array structure and a delay generator that reduces area usage. To achieve high-resolution ultrasound imaging acquisition with low computational power, we developed the Shift Coherence Factor (SCF) algorithm, which is hardware-friendly. This approach delivers a lateral resolution over 20% better than the conventional delay and sum (DAS) algorithm, with a contrast ratio of over 30 dB. The system was implemented in a 180 nm standard CMOS process with an area of 24.98 mm2, power consumption of 8.23 mW per channel, achieving a delay resolution of 8.33 ns, and a low-area implementation of 0.52 mm2 per channel. The system offers high-quality imaging acquisition with minimal additional area and power consumption, which has great potential for 3D imaging or catheterized ultrasound systems.

The phenomenon of seat occupancy in university libraries is a prevalent issue. However, existing solutions, such as software-based seat reservations and sensors-based occupancy detection, have proven to be inadequate in effectively addressing this problem. In this study, we propose a novel approach: a serial dual-channel object detection model based on Faster RCNN. Furthermore, we develop a user-friendly web interface and mobile APP to create a computer vision-based platform for library seat occupancy detection. To construct our dataset, we combine real-world data collection with UE5 virtual reality. The results of our tests also demonstrate that the utilization of personalized virtual dataset significantly enhances the performance of the convolutional neural network (CNN) in dedicated scenarios. The serial dual-channel detection model comprises three essential steps. Firstly, we employ Faster RCNN algorithm to determine whether a seat is occupied by an individual. Subsequently, we utilize an object classification algorithm based on transfer learning, to classify and identify images of unoccupied seats. This eliminates the need for manual judgment regarding whether a person is suspected of occupying a seat. Lastly, the web interface and APP provide seat information to librarians and students respectively, enabling comprehensive services. By leveraging deep learning methodologies, this research effectively addresses the issue of seat occupancy in library systems. It significantly enhances the accuracy of seat occupancy recognition, reduces the computational resources required for training CNNs, and greatly improves the efficiency of library seat management.

This paper has designed a four-channel wide dynamic microwave rectifier circuit for the shortcomings of uneven output voltage of each branch of the multi-channel rectification technology. A voltage-doubling rectifier circuit with identical structure was used in each branch. The four rectifier branches shared the same load at the output terminal, allowing the rectifier circuit to have an RF-DC conversion efficiency greater than 50% over the input power range from 12mW to 274mW, widened by 274% compared to a single channel. Not only the advantages of multi-channel technology with wide dynamics were retained, but also the output voltage was highly consistent and could be directly output in parallel without complex power electronics conversion.

With the dramatic increase in the number of mobile users and wireless devices accessing the network, the performance of the fifth generation (5G) wireless communication systems has been severely challenged. Reconfigurable intelligent surfaces (RIS), one of the potential technologies for the sixth generation (6G), has received a lot of attention. Since it is easier to deploy, consumes less power, and is inexpensive. RIS is an electromagnetic metamaterial that serves to reconfigure the wireless environment by adjusting the phase, amplitude and frequency of the wireless signal. To maximize channel transmission efficiency and improve the reliability of communication systems, the acquisition of channel state information (CSI) is essential. Therefore, an effective channel estimation method guarantees the achievement of excellent RIS performance. This paper conducts a comprehensive investigation of the existing channel estimation methods of RIS, analysis and comparison of channel model building and CSI acquisition schemes in different frequency bands, in addition to a comprehensive description of generic channel estimation methods, with a focus on the application of deep learning. Finally, we conclude the paper and provide an outlook in the future development of RIS channel estimation.

The effect of the communication channel size on the transport and subsequent detection of chemical messengers is investigated on millimetric and micrometric channels. The transport of the information carriers, being characterized by an advective and a diffusive contribution, was simulated by varying the flow velocity and the diffusion coefficient. Then, to evaluate the information quality, the Intersymbol Interference (ISI) between two consecutive signals at a specific release delay was estimated. This allowed us to verify that operating under micrometric channel conditions has a larger flow velocity range to obtain completely separated successive signals and smaller release delays can be used between signals. The theoretical results were confirmed by developing a prototype molecular communication platform operating under microfluidic conditions, which enables communication through fluorescent nanoparticles, namely Carbon Quantum Dots (CQDs).

In tele-monitoring, wireless body area networks (WBANs), sleep analysis and other applications involving electroencephalogram (EEG) signal, due to the high number of EEG recording channels, long recording time and several repetition of recordings to reach the highest signal-to-noise ratio, the amount of acquired data by the sensors is too large, demanding use of some compression procedure. Compressed sensing can be considered as one of the most effective compression methods in terms of compression ratio, which needs the underlying signal be sparse or have sparse representation in an appropriate domain. EEG signal is not sparse in time domain, therefore, in this paper correlation based weighted recursive least squares dictionary learning algorithm (CBW-RLS) is proposed that uses between-channel correlations to sparsify EEG signals. Due to the low-rank structure of EEG signals, exploiting between-channel correlations increase the sparsity level of the model while reducing the computational cost of dictionary learning procedure. This is done by merely updating the dictionary atoms which are involved in the sparse model of the previous data, reducing the total number of data used at each iteration and speeding up the dictionary learning algorithm. The simulation results show that the proposed method has better performance in terms of both quality of the EEG reconstruction and the computational cost compared to the other methods.

A novel 8-channel demux device based on multicore photonic crystal fiber (PCF) structures that operate at C-band range (1530-1565nm) has been demonstrated. The PCF demux design is based on replacing some air-holes areas with lithium niobate and silicon nitride materials over the PCF axis alongside with the appropriate optimizations of the PCF structure. The beam propagation method (BPM) combined with Matlab codes were used to modeled the demux device and to optimized the geometrical parameters of the PCF structure. Simulation results show that 8-channel can be demultiplexing after light propagation of 5 cm with large bandwidth (4.03-4.69nm) and crosstalk ((-16.88)-(-15.93) dB). Thus, the proposed device has a great potential to be integrated in dense wavelength division multiplexing (DWDM) technology for increasing performances in networking systems.

Calcium-activated chloride secretion in epithelial tissues described for many years. However, the molecular identity of the channel responsible for the Ca2+-activated Cl− secretion in epithelial tissues has remained a mystery. More recently, TMEM16A has been identified as a new putative Ca2 -activated Cl- channel (CaCC),. The primary goal of this article will be to review the characterization of TMEM16A, as it relates to the physical structure of the channel, as well as, important residues that confer voltage and Ca2+-sensitivity of the channel. This review will also discuss the role of TMEM16A in epithelial physiology and potential associated-pathophysiology. This will include discussion of developed knockout models that have provided much needed insight on the functional localization of TMEM16A in several epithelial tissues. Finally, this review will examine the implications of the identification of TMEM16A as it pertains to potential novel therapies in several pathologies.

An explosive growth in vehicular wireless services and applications gives rise to spectrum resource starvation. Cognitive radio has been used to vehicular networks to mitigate the impending spectrum starvation problem by allowing vehicles to fully exploit spectrum opportunities unoccupied by licensed users. Efficient and effective detection of licensed user is a critical issue to realize cognitive radio applications. However, spectrum sensing in vehicular environments is a very challenging task due to vehicles mobility. For instance, vehicle mobility has a large effect on the wireless channel, thereby impacting the detection performance of spectrum sensing. Thus, gargantuan efforts have been made in order to analyze the fading properties of mobile radio channel in vehicular environments. Indeed, numerous studies have demonstrated that the wireless channel in vehicular environments can be characterized by a temporally correlated Rayleigh fading. In this paper, we focus on energy detection for spectrum sensing and a counting rule for cooperative sensing based on Neyman-Pearson criteria. Further, we go into the effect of the sensing and reporting channels condition on spectrum sensing performance under temporally correlated Rayleigh sensing channel. For local and cooperative sensing, we derive some alternative expressions for average probability of miss detection. The pertinent numerical and simulating results are provided to further validate our theoretical analyses under a variety of scenarios.

Equal-Channel Angular Pressing (ECAP) is a method used to introduce severe plastic deformation into a metallic billet without changing its geometry. In special cases strain localization occurs and a pattern consisting of regions with high and low deformation (so-called shear and matrix bands) can emerge. This paper studies this phenomenon numerically adopting two-dimensional finite element simulations of one ECAP pass. The mechanical behavior of aluminum is modeled using phenomenological plasticity theory with isotropic or kinematic hardening. The effects of the two different strain hardening types are investigated numerically by systematic parameter studies: While isotropic hardening only causes minor fluctuations in the plastic strain fields, a material with high initial hardening rate and sufficient strain hardening capacity can exhibit pronounced localized deformation after ECAP. The corresponding finite element simulation results show a regular pattern of shear and matrix bands. This result is confirmed experimentally by ECAP-processing of AA6060 material in a severely cold worked condition, where microstructural analysis also reveals the formation of shear and matrix bands. Excellent agreement is found between the experimental and numerical results in terms of shear and matrix band width and length scale. The simulations provide additional insights regarding the evolution of the strain and stress states in shear and matrix bands.

The nitrogen-doped amorphous oxide semiconductor (AOS) thin film transistors (TFTs) with double-stacked channel layers (DSCL) were prepared and characterized. The DSCL structure composed of nitrogen-doped amorphous InGaZnO and InZnO films (a-IGZO:N/a-IZO:N or a-IZO:N/a-IGZO:N) made the corresponding TFT devices exhibit quite large field-effect mobility due to the existence of double conduction channels. Especially, the a-IZO:N/a-IGZO:N TFTs showed even better electrical performance (μ_FE = 15.0 cm²·V^-1·s^-1, SS = 0.5 V/dec, V_TH = 1.5 V, I_ON/I_OFF = 1.1×10⁸) and stability (V_TH shift of 1.5, -0.5, and -2.5 V for positive bias-stress, negative bias-stress and thermal stress tests, respectively) than the a-IGZO:N/a-IZO:N TFTs. Based on the X-ray photoemission spectroscopy measurements and energy band analysis, it was assumed that the optimized interface trap states, the less ambient gas adsorption, and the better suppression of oxygen vacancies in the a-IZO:N/a-IGZO:N hetero-structures might be responsible for the better behaviors of the corresponding TFTs.

This study posits that for appropriately explaining the complex charland (mid-channel island) processes and formulating policy and planning measures, a comprehensive understanding of the dynamic characteristics of the geomorphological, ecological, and human systems holistically is essential. This is also valid for the territorial and maritime areas of Bangladesh. The objectives of this study are: (i) to analyze the salient features and characteristics of the geomorphological and riparian systems of the Bengal Delta; (ii) to analyze the evolutionary discourse of the legal systems concerning eroded (diluvion) and accreted (alluvion) land in Bangladesh; and (iii) to assess characteristics of coping and adaptation strategies of the charland inhabitants. The findings reveal that the delta-building processes, characterized by the dynamic shifts of river channels, and erosion and accretion of charlands have made the land and water systems of the territory very dynamic and unstable – resulting in consistent displacement of settlers and serious deterioration of their socioeconomic status. The historical evolution of land laws and regulations concerning the accreted land favoured vested interests. As no effective institutional framework and structure presently exists in Bangladesh for resettlement planning, formulation of a comprehensive national resettlement policy is therefore urgently needed.

Plankton monitoring by microscopy offers long-term ecological perspective of plankton com-munities but different detection approaches are biased uniquely. Genetic identification of marine plankton has become standard but is still not used in routine monitoring. This study assessed the diversity of plankton taxa using 18S high throughput sequencing from 2011-2012 from small-volume (~200ml) samples from the Water and Microplankton Sampler (WaMS) deployed on the Continuous Plankton Recorder platform (CPR). The 18S-HTS survey revealed a bias towards heterotrophic taxa, and phototrophs under 10µm within the photosynthetic community. In comparison with phytoplankton microscopic counts from the CPR survey and Western Channel Observatory station L4, only 8-12 taxonomic families were common to all three surveys, with a bias towards larger diatoms and dinoflagellate taxa in microscopy surveys. The WaMS survey detected a contrasting but complementary taxa set to that of microscopic surveys. Additional Quantitative PCR was carried out on the picoeukaryotic pelagophyte, Aureococcus anophagefferens, and the nanoeukaryotic potential harmful algae, Pseudo-nitzschia delicatissima, from 2011-2013. This confirmed the persistence presence of A. anophagefferens in the Western Channel and an elevated abundance of both species in 2011. Species specific seasonality were distinct from those of aggregrate phytoplankton groups.

Flow experience, characterized by deep immersion and complete engagement in a task, is highly recognized for its positive psychological impacts. However, previous studies have been restricted to use a single type of task, and the exploration on its neural correlates has been limited. This study aimed to explore the neural correlates of flow experience with the employment of multifac-eted flow-induction tasks. Six tasks spanning mindfulness, artistic tasks, free recall, and varying levels of Tetris complexity (easy, flow, and hard conditions) were employed to have a relatively complete coverage of the known flow-induction tasks for a better induction of individualized flow experience. Twenty-eight participants were recruited to perform these six tasks, with a sin-gle-channel prefrontal electroencephalography (EEG) recording. Significant positive correlations were observed between the subjective flow scores of individual’s best-flow-experience task and the EEG activities at delta, gamma, and theta bands, peaking at latencies around 2 minutes after task onset. The outcomes of our multiple regression analysis yield a maximum coefficient of de-termination (R²) of 0.279. Our findings report the EEG correlates of flow experience in naturalistic settings and highlight the potential of portable and unobtrusive EEG technology for an objective measurement of flow experience.

The two-phase flow of water and reactive gas in the channel of proton exchange membrane fuel cell (PEMFC) plays an important role in high-quality water management. In this study, the removal effect of 3D wave channel and 2D straight channel for liquid water was studied by volume of fluid method. The dynamic behavior of droplet emerge from the gas diffusion layer (GDL) into the channel under the influence of gas flow was investigated. The effects of droplet growth, deformation, detachment, force, pore size on water critical behavior and water content in the channel are discussed. The results show that the 3D wave channel is superior to the removal of liquid water than the 2D straight channel. The increase of velocity is conducive to the discharge liquid water. While infinite increase of velocity will cause more parasitic power loss. The larger pore size of GDL is not advantageous to the performance of PEMFC, but the appropriate increase of pore size is conducive to the discharge of liquid water. The basic knowledge obtained in this study will help to deepen the understanding of droplet dynamics in PEMFC gas channels, and help to optimize the design and working conditions of these channels.

Environmental responsibility and economic benefits have promoted the development of closed-loop supply chain (CLSC), and shortages and channels are considered to be two important issues in CLSC. This paper explores ordering and channel decisions in CLSC with new and differentiated remanufactured products, and considers the price and sales effort-dependent demands, as well as the proportion of emergency orders determined by emergency order costs and backorder losses, and establishes an integrated and decentralized CLSC game models. We introduce a stochastic sales effort, which affects two types of products. Numerical results show that sales effort and the order quantity of new and remanufactured products exhibit concave and convex functions, respectively. Wherein, the upper limit of sales effort has a greater impact on supply chain decisions. High sales efforts can serve as a means of coordinating dispersed supply chains. Moreover, in different cases, decisions of integrated channel are better than those of decentralized channel. Finally, whether the supply chain adopts an emergency order strategy depends on the relative cost of emergency orders and out of stock costs. According to the research in this article, some management insights are also provided.

Blood testing is a crucial application in the field of clinical studies for disease diagnosis and screening, biomarkers discovery, organ function assessment, and personalized medication. Therefore, it is of utmost importance to collect precise data in a short time. In this study, we utilized Raman spectroscopy to analyze blood samples and extracted comprehensive biological information, including the primary components and compositions present in the blood. We conducted short-wavelength (532 nm green light) Raman scattering spectroscopy on blood samples, plasma, and serum, and subsequently analyzed the biological characteristics detected in each sample type. Our results indicated that whole blood had high hemoglobin content, which suggests that hemoglobin is a major component of blood. The characteristic Raman peaks of hemoglobin were observed at 690, 989, 1015, 1182, 1233, 1315, and 1562–1649 cm−1. Analysis of plasma and serum samples indicated the presence of β-carotene, which exhibited characteristic peaks at 1013, 1172, and 1526 cm−1. Additionally, in the field of medical blood testing, the novel 3D Silicon micro-channel device technology holds immense potential. It can serve as a substrate and helps to detect various diseases and biomarkers, providing real-time data to help medical professionals and patients better understand their health conditions. Changes in biological data collected in this manner could potentially be used to diagnose clinical diseases.

In this paper, we study the effect of parasitic channel on electrical characteristics and power consumptions of vertically stacked gate-all-around (GAA) silicon nanosheet (NS) MOSFETs of the bulk and silicon-on-insulator (SOI) substrates. Through deliberate control of the bottom parasitic channel coverage, we systematically assess its influence on DC, AC, and RF characteristics including power consumption. The observed findings highlight a significant differentiation among the bottom parasitic channels: GAA (i.e., control sample with 100% coverage), omega-shaped gate NS (70% and 80% coverages), and FinFET (60% coverage). Compared with the device with a 60% coverage channel, the device with a 100% coverage channel possesses 3520% and 8030% normalized leakage current improvement for both NFET and PFET under the bulk substrate, respectively. Compared with bulk-substrate devices, the SOI-substrate devices further significantly improve the leakage current. Due to enhanced off-state current leakages in the 100% covered bulk-substrate device, the static power demonstrates a notable improvement (about 98.1%), compared to 60% covered devices. Hence, the utilization of a 60% covered channel will result in a degradation of both device and circuit performance. The observation of GAA NS MOSFET indicates that an increase in the bottom parasitic channel coverage ratio leads to a positive impact on power consumption and leakage currents. The examination presented here is useful in the fabrication of stacked GAA NS MOSFETs.

This paper addresses the mixed convective flow and heat transfer in combustible third grade fluid through a slant channel that is filled with a permeable materials. The fluid layer in contact with the lower plate is exposed to convective heating with the ambient while at the upper plate, a constant heat flux is experienced. We employ the spectral quasilinearisation method (SQLM) to the coupled nonlinear flow governing equations. Fluid velocity and temperature profiles, local entropy generation and irreversibility ratio are computed and analysed quantitatively and qualitatively. A residual error analysis demonstrated high accuracy and convergence of the numerical method. The results on flow and thermal effects, entropy generation rate and Bejan number revealed fascinating manifestations that have profound implications in design of thermo-mechanical systems. In particular, the results of the thermal analysis are pertinent to optimal designs of systems that achieve efficient energy utilization.