Tailings generated by mining account for the largest proportion of global waste from industrial activities. Copper is relatively uncommon world-wide, with low concentrations in sediments and waters, yet is very elevated around mining sites. On the Keweenaw Peninsula of Michigan, USA, jutting out into Lake Superior, 140 mines extracted native copper from the Portage Lake Volcanic Series, part of an intercontinental rift system. Between 1901-1932, two mills at Gay (Mohawk, Wolverine) sluiced 22.7 million metric tonnes (MMT) of copper-rich tailings (stamp sands) into Grand (Big) Traverse Bay. Here we examine: 1) 3D coastal elevation and reef bathymetry, 2) particle dispersal, 3) copper concentrations and leaching, plus 4) shoreline toxicity. About 10 MMT of tailings created a migrating coastal beach that stretches 7 km from the Gay pile to the Traverse River Seawall. Another 10 MMT are moving underwater on the coastal shelf, threatening Buffalo Reef, an important lake trout and whitefish breeding ground. Aerial photos, ALS (plane) LiDAR, and relatively inexpensive UAS (drone) surveys characterize shoreline structure and aid initial remediation. Because sands (natural beach quartz, stamp sand basalt) are silicates of similar density, particle dispersal is similar and challenging. However, stamp sand beaches contrast greatly with natural sand beaches in both physical profile and chemistry. Dispersing particles retain copper, and release toxic concentrations. Leaching is elevated by exposure to high DOC and low pH waters. Field experiments, shoreline seining, and benthic sampling confirm serious impacts on aquatic biota, supporting tailings removal.

Beef has one of the highest climate footprints of all foods, and therefore the hamburger has been targeted for substitution by numerous plant-based alternatives. However, many consumers find the taste of these alternatives lacking, and thus we proposed a hybrid meat and plant-based burger as a lower threshold alternative for these consumers. The burger was made from 50% meat (beef and pork, 4:1) and 50% plant-based ingredients, including texturised legume protein and had a climate footprint less than half that of a beef burger. Texture and sensory properties were evaluated instrumentally and through a consumer survey (n = 381) using the check-all-that-apply (CATA) method. Moisture properties indicated a significantly juicier eating experience for the hybrid compared to a beef burger, which was supported by the CATA survey. From texture profile analysis the hybrid burger was significantly softer and less cohesive than a beef burger. Despite having different CATA term profiles overall liking of the hybrid and a beef burger were not significantly different. Penalty analysis indicated that “meat flavour”, “juiciness”, “spiciness”, and “saltiness” are the most important attributes for a burger. In conclusion, consumers may be open to reducing their meat consumption by way of hybrid meat and plant-based products.

Assessment of extreme events and climate change on reservoir inflow is important for water and power stressed countries. Projected climate is subject to uncertainties related to climate change scenarios and Global Circulation Models (GCMs’). Extreme climatic events will increase with the rise in temperature as mentioned in the AR5 of the IPCC. This paper discusses the consequences of climate change that include extreme events on discharge. Historical climatic and gauging data were collected from different stations within a watershed. The observed flow data was used for calibration and validation of SWAT model. Downscaling was performed on future GCMs’ temperature and precipitation data, and plausible extreme events were generated. Corrected climatic data was applied to project the influence of climate change. Results showed a large uncertainty in discharge using different GCMs’ and different emissions scenarios. The annual tendency of the GCMs’ is bi-vocal: six GCMs’ projected a rise in annual flow, while one GCM projected a decrease in flow. The change in average seasonal flow is more as compared to annual variations. Changes in winter and spring discharge are mostly positive, even with the decrease in precipitation. The changes in flows are generally negative for summer and autumn due to early snowmelt from an increase in temperature. The change in average seasonal flows under RCPs’ 4.5 and 8.5 are projected to vary from -29.1 to 130.7% and -49.4 to 171%, respectively. In the medium range (RCP 4.5) impact scenario, the uncertainty range of average runoff is relatively low. While in the high range (RCP 8.5) impact scenario, this range is significantly larger. RCP 8.5 covered a wide range of uncertainties, while RCP 4.5 covered a short range of possibilities. These outcomes suggest that it is important to consider the influence of climate change on water resources to frame appropriate guidelines for planning and management.

Given the opportunities offered by foreign investment in energy infrastructure mostly by Chinese firms, the Government of Cambodia is giving high priority to developing hydropower resources for reducing energy poverty and powering economic growth. Using a “Political ecology of the Asian drivers” framework, this paper assesses China’s involvement in the development of large dams’ in Cambodia and its impacts on the access of natural resources such as water and energy by dam builders, local communities and the government. This analysis is based on 61 interviews and 10 focus group discussions with affected communities, institutional actors, Chinese dam builders and financiers in relation to the first large Chinese dam built in Cambodia, the Kamchay dam. Based on the results of the analysis this paper makes recommendations on how to improve the planning, implementation and governance of large dams to ensure that the dams’ benefits are shared more equally.

Flooding, exacerbated by climate change, poses a significant threat to certain areas, increasing in frequency and severity. In response, the construction of supplementary dams has emerged as a reliable solution for flood management. This study employs a Remote Sensing (RS) approach integrated with GIS to assess the feasibility of constructing a supplementary dam near Linville, Brisbane, Australia, with the aim of mit-igating floods and preventing overtopping failure at the Wivenhoe Dam. Using QGIS software and a 25-meter resolution DEM from the Queensland Spatial Catalogue ‘QSpatial’ website, four potential dam sites were analysed, considering cross-sections, watershed characteristics, and water volume calculations. Systematic selection criteria were applied to identify the most optimal option based on dam wall di-mensions, volume-to-area, and volume-to-cost ratios. The selected option was further assessed against predefined criteria, yielding one optimal choice. The study provides insights into the feasibility and ef-fectiveness of supplementary dam construction for flood mitigation in the region, with recommendations for future research and implementation.

Beginning with navigation system design, this paper presents a comprehensive strategy for enhancing the search and rescue capabilities of agile mobile robots. Towards this, the autonomous ground vehicle (AGV) utilizes surface classification to determine and prioritize the terrain it is traversing. Our developed system design incorporates real-time terrain data with task objectives at a high level, ensuring that the robot can effectively navigate complex and ever-changing environments. This design, in conjunction with the introduction of a novel lightweight surface classification model, forms the basis of our adaptive terrain perception and decision-making systems, enabling robots such as Jackal to adapt rapidly and make the decisions necessary to complete the task. Subsequently, we exhaustively validated these systems through a series of extensive experiments in a variety of terrains, including normal and mixed terrains, demonstrating their robustness and efficacy in real-life situations.

The mining sector generates a substantial quantity of stone waste and tailings, which constitutes an environmental risk. The most prevalent method for disposing of this industrial waste is dumping, which contributes to soil deterioration and water contamination while acquiring precious land. It can be recycled using a number of processes, such as the promising geopolymerization technique, which transforms waste into value. This study reviews current developments in the manufacturing of mine tailings-based geopolymer composites from industrial waste as a possible sustainable building material. This paper also gives in-depth studies on the characteristics and behaviors of mine tailings composites used in geopolymer manufacturing, including durability, microstructure, thermal and leaching properties. This review also identifies knowledge gaps that must be filled in order to advance mine tailings composites for geopolymers.

The catastrophic failure of two dams in Libya in the night of 10th and 11th September 2023, resulted in a significant amount of water and debris destroying a large part of the city of Derna, which is located downstream of the two dams. The flood caused more than 6000 fatalities and the dis-placement of thousands of people from the city. The dams failed due to heavy rainfall caused by the Medicane Daniel, resulting in intense precipitation and the dams overspilling after reaching full capacity. This paper analyses the consequences of the dam breach by modelling the flow discharge and the flooding of the city of Derna. The analysis compares the computed quantities with the findings of the post-event satellite image analysis from UNOSAT and Copernicus, the field reports, and information gathered from the social media through AI detection. The results allows to better understand the dynamics of the dam breach, its initial parameters and an assessment of the accu-racy of the results.

GNSS receivers are nowadays commonly used in monitoring applications, e.g., in estimating crustal and infrastructure deformations. This is basically due to the recent improvements in GNSS instruments and methodologies that allow high precision positioning, 24 h availability and semiautomatic data processing. In this paper, GNSS estimated deformations on a dam structure have been analyzed and compared with pendulum data. This study has been carried out for the Eleonora D’Arborea (Cantoniera) dam, which is in the Sardinia Island. Time series of pendulum and GNSS over a time span of 2.5 years have been aligned so to be comparable. Analytical models fitting these time series have been estimated and compared. Those models were able to properly fit pendulum data and GNSS data, with standard deviation of residuals smaller than one millimeter. This encouraging results led to the conclusion that GNSS technique can be profitably applied to dam monitoring allowing a denser description, both in space and time, of the dam displacements than the one based on pendulum observations.

Mining is an important industry, accounting for 6.9% of global GDP. However, global development promotes accelerated demand, resulting in the accumulation of hazardous waste in land, sea, and air environments. It reached 7 billion tonnes of mine tailings generated yearly worldwide, and 19 billion solid tailings will be accumulated by 2025. Adding to this, the legacy of environmental damage from abandoned mines is worrying; in Canada there are around 10,000 abandoned mines, 50,000 in Australia, 6,000 in South Africa, and 9,500 coal mines in China, reaching 15,000 by 2050. In this scenario, restoration techniques from mining tailing have become increasingly discussed among scholars due to their potential to offer benefits towards reducing tailings levels, thereby reducing environmental pressure for the correct management and adding value to previously discarded waste. This review paper explores available literature on the main techniques of mining tailing recycling and reuse and discusses leading technologies, including the benefits and limitations, as well as emerging prospects. The findings of this review serve as a supporting reference for decision-makers concerning the related sustainability issues associated with mining, mineral processing, and solid waste management.

Dam breaches have catastrophic consequences, causing severe property damage, life loss, and environmental impact. The Kulekhani reservoir rockfill dam break was studied to evaluate the downstream impact. The appropriate breaching parameter of MacDonald and Langridge (1984) regression equations was selected based on the sixteen observed dam failure cases and cross-sectional geometry of the existing dam of Kulekhani. The 2D Diffusion Wave and Full Dynamic Wave Equation were applied for downstream flood assessment, Full Dynamic Wave was able to capture the physical flow phenomena like river bend effects resulting in higher flow velocity at the outer bend, and formation of eddies considering losses. The application of a Full Dynamic Equation was found to be appropriate for rapidly varying unsteady flow considering steep slopes, and sudden changes in channel geometry. Flood mapping of water depth, flow velocity, flood intensity, and arrival time were carried out for flood hazard assessment classified by the American Society of Civil Engineers (ASCE). Flow depth and extension of the flow area were compared to identify the affected area, higher flow depth and larger extension were observed using a Full Dynamic Wave Equation as a result of less flow velocity considering the losses. Almost 17 minutes of the arrival time of peak difference at the Bagmati River confluence was evaluated between the models which plays an important role in decision-making for selection of the flood model. Flood mitigation with river diversion works through a hydraulic measure of Levee was suggested to protect the highly affected households of Ranche, Nagmar, Khanikhet, and Debaltar towns. Most of the household was found to be safe after the construction of the Levee except for eleven houses that lie along the river below flood elevation of 1269.6 m.a.s.l. This signifies the importance of room for the rivers and the human settlement near the river might be life-threatening.

Determination of the parameters of the movement of surrounding objects, and in particular their speed, is one of the basic skills of a human being. The study of development of basic concepts of motion has been done for years with different methods and in different contexts. We have analyzed the effect of the physical/scientific image of the world introduced to children by school education and its long- and short-term cognitive consequences. Our studies showed that children differentiate the concept of speed into two more specific concepts: average speed and instantaneous velocity. In the present work we present how the gender context is superimposed on this general picture. We found that initial, genuine pre-school concept of speed of girls and boys is, on average, different. Our analysis shows also that this gender effect vanishes quickly together with the appearance of physical definitions of kinematical quantities in physics/science curricula. We discuss also methodological aspect of the statistical ‘gender gap’ measure and we calculated the gender effect chance probability, p-value, to be slightly less than 0.001. The importance of observed effect for the sustainable science teaching processes is discussed.

Estimation of the potential consequences from events occurring downstream of a dam are part of the risk assessment needed during the installation phase of a new dam. In case of specific Natural or Man Made ongoing or prospected events, it may be also important to carry out fast computations that can provide information on the areas at risk either because the original design analyses are not available or because the parameters needed are different. This study is aimed to develop a procedure that strongly facilitates the preparation of the input deck and the derivation of the output quantities to allow a fast analysis of a dam break event using a shallow water model, NAMI DANCE, as the analysis tool.

Background: Gastric cancer (GC) is the second most prevalent cancer in Korea, significantly impacting morbidity and mortality. While advancements in early detection and treatment have improved survival rates, managing post-surgical recovery remains vital. Herbal medicine (HM) has emerged as a potential adjunct therapy to enhance recovery and quality of life (QoL) in patients post-GC surgery. Methods: This systematic review and meta-analysis evaluated the efficacy and safety of HM in the post-surgical recovery of GC patients. We searched both Korean and international databases, identifying 16 randomized controlled trials (RCTs) meeting our criteria. We assessed study quality using the Cochrane Risk of Bias tool and analyzed data with Review Manager Software (RevMan). Results: Our analysis included 1,546 patients from the selected studies, demonstrating that HM significantly improved gastrointestinal recovery times, including time to first flatus, bowel movement, and return of bowel sounds. Significant improvements were also seen in nutritional markers such as albumin and prealbumin, alongside beneficial effects on immune markers like CD3+ and CD4+ levels. QoL assessments using WHOQOL-BREF and QLQ-C30 scores indicated substantial improvements. HM had a favorable safety profile, showing a reduced incidence of adverse effects compared to controls. Conclusion: The findings suggest that HM can significantly enhance recovery and improve the quality of life following gastric cancer surgery, with a favorable safety profile. However, due to considerable heterogeneity in study results, extended clinical trials and rigorous follow-ups are recommended to assess long-term effects and side effects comprehensively.

Mineral extraction is one of the most important for the economies of different countries, and Brazil is one of the world's primary iron ore producers. Unfortunately, the dams are still the main problem, mainly in Minas Gerais, especially after the Fundão Dam rupture happened in 2015. Additionally, there is still a massive presence of buildings produced on earth throughout the Minas Gerais mining region, built from the 18th century to today. Investigating the potential of IOT to be incorporated into traditional earthen construction techniques in regions affected by dam ruptures presents a relevant and innovative research approach. In addition, the local reuse of these sediments should be the priority. Thus, the main objective of this work was to collect, characterize, and analyze the possibilities of application of these tailings to produce RE. XRD, XRF, granulometry, porosity, specific density, toxicity, and MEV/EDS were performed on the samples collected at three points. To analyze the soil-IOT compatibility, representative mixtures of RE were produced, and the specific mass, compaction, and compressive strength were performed. It was observed that the IoT samples have a high silica content and that the mixtures of IOT-soil, even without cement, reached compressive strength values above the current international standards.

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

This work presents the production and incorporation of calcium hydrolyzed nano-solutions at three concentrations (1, 2, and 3 wt.%) in alkali-activated gold mine tailings (MTs) from Arequipa, Perú. A first activator solution of sodium hydroxide (NaOH) at 10M was used. The calcium hy-drolyzed nano-solutions acted as a secondary activator and as additional calcium resource for the alkali-activated materials (AAMs) based on the low-calcium gold MTs. High-resolution trans-mission electron microscopy/energy-dispersive x-ray spectroscopy (HR-TEM/EDS) analyses were carried out to characterize the morphology, size, and structures of the calcium hydrolyzed na-noparticles. Fourier transform infrared (FTIR) analyses then were used to understand the chemical bonding interactions in the calcium hydrolyzed nanoparticles and in the AAMs. Scanning electron microscopy/energy-dispersive X-ray spectroscopy (SEM/EDS) and Quantitative X-ray diffraction (QXRD) were performed to study the structural, chemical, and phase compositions of the AAMs; uniaxial compressive tests evaluated the compressive strength of the reacted AAMs; and Nitrogen adsorption-desorption analyses measured the porosity changes at nanostructure level in the AAMs. The results indicate that each increase in the concentration of the calcium hydrolyzed nano-solution had a direct/proportional effect on the mechanical properties of the AAMs samples. The AAMs with 3 wt.% calcium-hydrolyzed nano-solution had the highest compressive strength value of 15.16 MPa, which represented an increase of 62% compared to the original system without nanoparticles and aged under the same conditions of 70°C for seven days. These results provide useful information about the positive effect of calcium-hydrolyzed nanoparticles on gold MTs and their conversion into sustainable building materials through alkali activation.

It is well recognised that the mining industry in South Africa is highly rated for its substantial contribution to the country’s economic growth, including employment and infrastructural development. It is also known that mining and ore processing activities potentially pose a severe threat to public health and environmental well-being, in the way operations are carried out, mine wastes are disposed of (in dumps), local communities are relocated, mine management and the mining community in general, perceive established environmental standards and etiquette. This paper examines ethical practices and norms in the South African mining industry, with particular reference to the management of tailings dams. We analyse the modes of articulation of the country’s regulatory instruments for tailings management, and review the corporate social responsibility (CSR) approach of leading mining companies. Despite decades of research and resulting recommendations on tailings management, it is concluded that current legislations are largely ineffective, level of adherence by mine management and the mining community, low, and mechanisms for compliance monitoring, weak. New perspectives on legislative issues for unsolved problems in tailings handling are put forward, and directions for future research, indicated.

Jasmonates (JAs), including jasmonic acid (JA) and its biologically active derivative JA-Ile, are lipid-derived plant signalling molecules. They govern plant responses to stresses, such as wounding and insect herbivory. Wounding elicits a rapid increase of JA and JA-Ile levels as well as the expression of JAR1, coding for the enzyme involved in JA-Ile biosynthesis. Endogenous increase and application of JAs, such as MeJA, a JA methylester, result in increased defence levels, often accompanied by diminished growth. The function of jarin-1 in Arabidopsis thaliana was assessed. To investigate whether jarin-1 does function similarly in other plants, we tested this in Medicago truncatula, Solanum lycopersicum, and Brassica nigra seedlings in a root growth inhibition assay. Application of jarin-1 alleviated the inhibition of root growth after MeJA application in M. truncatula seedlings, proving that jarin-1 is biologically active in M. truncatula. Jarin-1 did not show, however, a similar effect in S. lycopersicum and B. nigra seedlings treated with MeJA. Even JA-Ile levels were not affected by application of jarin-1 in wounded leaf disks from S. lycopersicum. Based on these results, we conclude that the effect of jarin-1 is highly species-specific. Researchers intending to use jarin-1 for studying the function of JAR1 or JA-Ile in their model plants, must test its functionality before use.

Fibre-based dietary interventions are at the forefront of gut microbiome modulation research, with a wealth of 16S rRNA information to demonstrate the prebiotic effects of isolated fibres. However, there is a distinct lack of data relating to the effect of a combination of soluble and insoluble fibres in a convenient to consume fruit juice food matrix on gut microbiota structure, diversity, and function. Here, we aimed to determine the impact of the MOJU Prebiotic Shot, a fruit juice drink blend containing chicory inulin, baobab, golden kiwi, and green banana powders, on gut microbiota structure and function. Healthy adults (n = 20) were included in a randomized, double-blind, placebo-controlled, cross-over study receiving 60ml MOJU Prebiotic Shot or pla-cebo (without the fibre mix) for 3 weeks with a 3-week wash-out between interventions. Shotgun metagenomics revealed significant between-group differences in alpha and beta diversity. In addition, the relative abundance of the phyla Actinobacteria and Desulfobacteria was significantly increased as a result of the prebiotic intervention. 9 species were observed to be differentially abundant (uncorrected p-value of <0.05) as a result of the prebiotic treatment. Of these, Bifidobacterium adolescentis and CAG-81 sp900066785 (Lachnospiraceae) were present at increased abundance relative to baseline. Additionally, KEGG analysis showed an increased abundance in pathways associated with arginine biosynthesis and phenylacetate degradation during the prebiotic treatment. Our results show the effects of the daily consumption of 60ml MOJU Prebiotic Shot for 3 weeks and provide insight to the functional potential of B. adolescentis

Iron tailings are solid waste generated after the mining of iron mines, which have caused serious damage to the surrounding ecology and environment and have attracted widespread attention. By analyzing the formation causes, main components, and environmental effect mechanisms of iron tailings, the article systematically elaborates on the degree and mechanism of the harm of iron tailings to water bodies, atmosphere, soil, and ecosystems, and evaluates its impact on human health and sustainable development of society. On this basis, specific prevention and control measures have been proposed to reduce iron tailings emissions, realize resource recycling, and restore ecosystems. Research shows that iron tailings containing heavy metals can widely pollute the environment through dissolution and migration, and have significant biological toxicity effects. The research results can provide a theoretical reference for decision-making departments to formulate scientific and reasonable iron tailings disposal and ecological protection policies. It is recommended to strengthen specific research on the infiltration of toxic and harmful components in tailings in the future, and develop efficient and stable solidification technology, and vegetation-microbial joint restoration models to further reduce the ecological and environmental risks of iron tailings.

In recent years, cemented tailings/paste backfill (CPB) become more and more important to maintain mine structure and keep mining stope to be stable in deep underground mining. Deep mining process often accompanied by blasting, rock burst and other high-speed dynamic loading. So it’s important to make research on dynamic behavior and characteristics of CPB. In this paper, a series of dynamic loading tests on CPB specimens by SHPB were taken to study the characteristic of stress-strain, dynamic strength, deformation and failure of CPB. The experimental results revealed that some CPB specimens have 1~2 lower stress peaks after reaching the peak stress before getting completely failed. The greater the cement-sand ratio was, the more obvious of strain reaction was. This property mainly showed like follows. The greater the cement-sand ratio was, the greater the dynamic compressive strength was under similar velocity impact; the dynamic compressive strength and the average strain rate were quadratic equation relationship, and the greater the cement-sand ratio was, the higher increase rate of dynamic compressive strength caused by strain rate. The dynamic compressive strength enhancement factor increased with the increase of the strain rate, and is larger than that of rock samples. The failure forms of CPB specimens under low-speed impact were almost the same as them under static uniaxial and triaxle compression. The CPB specimens were crushed broken under the critical strain rate, similar to the failure mode of low strength concrete. The experimental research results will improve our understanding the dynamic mechanical property of CPB and help to guide the strength design of deep mining backfill.

Copper mine tailings are the residual products after the purification of precious copper from copper ores, and their storage can create numerous environmental problems. Many researchers have used copper mine tailings for preparation of geopolymer. This paper studies the enhancement of the cementitious activity of copper mine tailings in geopolymer system. First, copper mine tailings are activated through a mechanical grinding activation. Afterward, the mechanically activated copper mine tailings are further processed through thermal activation and alkaline roasting activating. The cementitious activity index of copper mine tailings is characterized through the degree of concentration of alkali leaching silicon and aluminum. It was observed that the Si and Al alkali leaching concentration of mechanical activated tailings was increased by 26.03% and 93.33%, respectively. The concentration of Si and Al was increased by 54.19% and 119.92%, respectively. For alkaline roasting activating, roasting time, temperature and (C/N ratio) were evaluated through the orthogonal test, and the best condition was activation for 120 min at 600℃ with C/N ratio is 5:1. In this study, the SEM, XRD and IR analysis show that mechanically activation, thermal activation and alkaline roasting activating can improve the cementitious activity index of copper mine tailings.

Mining and processing tailings often contain significant amounts of valuable metals, that can represent valuable sources of secondary raw materials. Especially this is case in early-stage operations, in which the head grades were higher, and the tailings were higher grade. These tailings can also present a substantial risk to the environment. Serbia has copper deposits which have been exploited since ancient times, and these operations have generated large amounts of mineral processing tailings. The main objective of this study is to show how valuables can be recovered from chemically and mineralogically challenging tailings. After detailed chemical and mineralogical characterization, the laboratory scale flotation tests focused on evaluating the effect of particle size, different types of collectors, pH, and pulp potential. Based on the test work, copper and gold can be recovered effectively into pyrite concentrate

: In Chile, most tailings impoundments are in Northern and Central Chile, 20% of them are abandoned. Municipal budgets to manage these environmental liabilities are very limited and the use of native and endemic plant species to remove heavy metals from tailings is a low-cost alternative. Ex-situ phytoremediation experiments were conducted over seven months to evaluate the potential of Lycium chilense and Haplopappus foliosus to remove copper and lead from mine tailings. The results indicate that both species can concentrate high levels of both elements and they present removal efficiencies for Cu close to 50%. The best performance was presented by Haplopappus foliosus, accumulating higher concentrations of both metals than Lycium chilense. Also, it presents a bioconcentration over 1.

Deterministic simulations using the SWAN model were conducted along a stretch of the Tietê-Paraná waterway in the Ilha Solteira dam reservoir, São Paulo, Brazil, to assess the water waves generated by winds. Simultaneously employs a probabilistic metamodeling approach (PCE) and Sobol indices, to quantify uncertainty of the five involved physical parameters (wind velocity and direction, bottom friction (JONSWAP), whitecapping and depth-induced breaking index). In the deterministic part, Janssen’s formulation yielded the most successful and accurate estimations of wave heights. Probabilistic analysis underscored the importance of wind data and the whitecapping parameter in model calibration, with a significant influence of wind speed indicated by Sobol indices. The results not only refined the model calibration process, but also allowed the creation of contour maps for wave height and period that offer practical pre-project applications. This work advances understanding of wind wave hydrodynamics deterministically and probabilistically, with good concordance and performance indices compared to field data, despite being scarce.

The risk related to embankment dam breaches needs to be evaluated in order to prepare emergency action plans. The physical and hydrodynamic parameters of the flood wave generated from dam-failure event correspond to various breach parameters such as width, slope and formation time. This study aimed to simulate dam-breach failure scenario of Yabous dam (NE Algeria) and analyze its influence on areas (urban and natural environments) downstream the dam. The simulation was completed using the sensitivity analysis method in order to assess the impact of breach parameters on the dam-break scenario. The propagation of flood wave associated to dam-break was simulated using the one-dimensional HEC-RAS hydraulic model. This study ap-plied a sensitivity analysis of three breach parameters (slope, width, and formation time) in five sites selected downstream the embankment dam. The simulation showed that the maximum flow of the flood wave recorded at the level of the breach was 8768 m3/s, which gradually attenuated along the river course to reach 1579.2m3/s at about 8.5km downstream the dam. This study estab-lished the map of flood-prone areas that illustrated zones threatened with the flooding wave trig-gered by the dam failure due to extreme rainfall events. The sensitivity analysis showed that flood wave flow, height and width revealed positive and similar changes for the increase in adjustments (±25% and ±50%) of breach width and slope in the 5 sites. However, flood wave parameters of breach formation time showed significant trends that changed in the opposite direction compared to breach slope and width.

Dams are a critical infrastructure system for many communities, but they are also one of the most challenging to inspect. Dams are typically very large and complex structures, and the result is that inspections are often time-intensive and require expensive, specialized equipment and training to provide inspectors with comprehensive access to the structure. The scale and nature of dam inspections also introduces additional safety risks to the inspectors. Unmanned aerial vehicles (UAV) have the potential to address many of these challenges, particularly when used as a data acquisition platform for photogrammetric three-dimensional (3D) reconstruction and analysis, though the nature of both UAV and modern photogrammetric methods necessitates careful planning and coordination for integration. This paper presents a case study on one such integration at the Brighton Dam, a large-scale concrete gravity dam in Maryland, USA. A combination of multiple UAV platforms and multi-scale photogrammetry was used to create two comprehensive and high-resolution 3D point clouds of the dam and surrounding environment at intervals. These models were then assessed for their overall quality, as well as their ability to resolve flaws and defects that were artificially applied to the structure between inspection intervals. The results indicate that the integrated process is capable of generating models that accurately render a variety of defect types with sub-millimeter accuracy. Recommendations for mission planning and imaging specifications are provided as well.

Maintaining an adequate micronutrient status can be achieved by following a complete, diverse diet. Yet, food trends in Western countries show suboptimal consumption of healthy nutrients. In this study we explored the prevalence of vitamin and mineral imbalances in a general population cohort of Dutch adults, and evaluated the effect of a digital lifestyle program on the nutritional status and nutrition health behaviors of these individuals. A micronutrient panel was measured in 348 participants, alongside a dietary assessment. One-hundred users subsequently underwent a remeasurement. We identified at least one nutritional imbalance in 301 individuals (86.5%). 80% improved and normalized B6, 67% improved folate, 70% improved B12, and 86% improved vitamin D. Iron abnormalities were corrected in 75% of participants. In conclusion, this study found micronutrient deficiencies of easily obtainable vitamins through diet or supplementation such as B vitamins and vitamin D were more prevalent than expected in a Dutch population. This can partly be explained by an insufficient consumption of food groups rich in B vita-mins. Our preliminary results in those remeasured after a digitally-enabled lifestyle intervention show these imbalances can be corrected with adequate behavioral support in a “food as medicine” approach complemented with supplementation where needed.

We are in amidst of COVID-19 pandemic. Since Dec 2019, severe acute respiratory corona virus (SAR-CoV-2) has infected more than half a billion people killing nearly 7 million people worldwide. Now the BA.5 variant of SARS-CoV-2 is causing mayhem and driving the global surge. Epidemiologist are aware of the fact that this virus is capable of escaping immunity and likely to infect the same person multiple times despite adequate vaccination status. Elderly people of age more than 60 years and those with underlying health conditions are considered as high-risk who are likely to suffer complications and death. While it is tempting to frame complications and mortality from COVID-19 as a simple matter of too much of a virulent virus in too weak of a host, much more is at play here. Framing the pathophysiology of COVID-19 in the context of the Chrousos and Gold model of the central stress response system can shed insight into its complex pathogenesis. Understanding the mechanisms by which pharmacologic modulation of the central stress response system via administration of clonidine and/or dexamethasone may offer an explanation as to why a viral pathogen can be well tolerated and cleared by one host while inflaming and killing another.

Abstract: Green walls and green dams are increasingly being considered as part of many nation-al and international desertification initiatives. This paper studies the spatiotemporal evolution of the green dam in the Moudjbara region (Djelfa Province, Algeria) from 1972 to 2019 by using Landsat imagery, Land Change Modeler and Open Land package. The future evolution of pine plantations for the year 2029 was also forecasted, based on an anthropogenic scenario (i.e., an-thropogenic pressure is the main driver of the green dam destruction). Our findings revealed that the green dam project was successful for a few years, but after that, pine plantations deteri-orated significantly due to forest harvesting, livestock overgrazing, and the proliferation of the pine caterpillar processionary, which destroyed most of the reforestation. Land Change Modeler predicted a huge degradation of pine plantations for the year 2029, and if the deforestation con-tinues at the same rate, the green dam will disappear in the Moudjbara region during the next few decades. Aware of this threat, the Algerian authorities are now planning to reforest more than 1.2 million ha under the latest rural renewal policy by introducing new principles related to sustainable development, fighting desertification, and climate change adaptation

In large infrastructures such as dams, which have a relatively high economic value, ensuring the proper operation of the associated hydraulic facilities in different operating conditions is of utmost importance. To ensure the correct and successful operation of the dam's hydraulic equipment and prevent possible damages, including gates and downstream tunnel, to build laboratory models and perform some tests are essential (the advancement of the smart sensors based on artificial intelligence is essential). One of the causes of damage to dam bottom outlets is cavitation in downstream and between the gates, which can impact on dam facilities, and air aeration can be a solution to improve it. In the present study, six dams in different provinces in Iran has been chosen to evaluate the air entrainment in the downstream tunnel experimentally. Three artificial neural networks (ANN) based machine learning (ML) algorithms are used to model and predict the air aeration in the bottom outlet. The proposed models are trained with genetic algorithms (GA), particle swarm optimization (PSO), i.e., ANN-GA, ANN-PSO, and ANFIS-PSO. Two hydrodynamic variables, namely volume rate and opening percentage of the gate, are used as inputs into all bottom outlet models. The results showed that the most optimal model is ANFIS-PSO to predict the dependent value compared with ANN-GA and ANN-PSO. The importance of the volume rate and opening percentage of the dams' gate parameters is more effective for suitable air aeration.

Malaria is a disease spread by female mosquitos of the Anopheles genus. It is acutely prevalent in Sub-Saharan Africa, where 90% of malaria deaths occur annually. One Sub-Saharan African country historically impacted by malaria is Ethiopia. In the past twenty years, malaria prevalence has decreased throughout Sub-Saharan Africa; yet, anthropogenic environmental changes are changing the landscape of malaria. Scholarly literature has cited a positive relationship between hydroelectric dams and malaria in Sub-Saharan Africa. Ethiopia is currently expanding their hydroelectric infrastructure. The Gilgel Gibe III Dam is located on the Omo River in Southwestern Ethiopia. It began generating electricity in 2015 and its reservoir has a capacity of 14,700 million m3 of water. This research utilized Geographic Information Systems and Remote Sensing to identify populations at an increased risk of malaria due to Gilgel Gibe III Dam. Two different techniques were employed: the proximity approach and the remote sensing approach. The proximity approach was based on distance from the reservoir. It identified all populations living within three kilometers of the reservoir as being at an increased risk. The remote sensing approach evaluated the slope, elevation, water content, and land surface temperature of the study area to create a mosquito breeding habitat risk map. Then, populations living within three kilometers of the two main High-Risk areas were identified. This study suggests that mosquito breeding habitat risk is not equally distributed throughout the Gilgel Gibe III Reservoir. This causes certain populations to be at a heightened risk of malaria.

Worldwide, it is estimated that at least 1 in 4 adults suffers from hypertension, and this number is expected to increase as populations grow and age. Blood pressure (BP) possesses substantial heritability, but is also heavily modulated by lifestyle factors. As such, digital, lifestyle-based in-terventions are a promising alternative to standard care for hypertension prevention and man-agement. In this study we assessed the prevalence of elevated and high BP in a Dutch general pop-ulation cohort undergoing a health screening, and observed the effects of a subsequent self-initiated, digitally-enabled lifestyle program on BP regulation. Baseline data were available for 348 participants, of which 56 had partaken in a BP-focused lifestyle program and got re-measured 10 months after the intervention. Participants with elevated SBP and DBP at baseline showed a mean decrease of 7.2 mmHg and 5.4 mmHg, respectively. Additionally, 70% and 72.5% of participants showed an improvement in systolic and diastolic BP at remeasurement. These improvements in BP are superior to those seen in other recent studies. The long-term sustainability and the efficacy of this and similar digital lifestyle interventions will need to be estab-lished in additional, larger studies.

Dams have made great contributions to human society, facilitating flood control, power generation, shipping, agriculture and industry. However, the construction of dams greatly impacts downstream ecological environments and nearby marine areas. To summarize these impacts, this review used recent research to comprehensively analyze how dam construction has affected river hydrology, geomorphology, and ecosystem of downstream reaches globally. Effects of dams on ecosystems occur through reduced river flow, reduced sediment flux, altered water temperature, changed estuary delta, altered composition and distribution of nutrients, altered structure and distribution of phytoplankton populations, caused habitat fragmentation, and blocked migration routes in river sections and adjacent seas. Besides, exploring new reservoir management strategies (including targeted control of dam storage and flushing sediment operations), banning fishing activities, and removing unnecessary dams (obsolete or small dams) are becoming crucial tools for ecosystem restoration.

Water pollution is a common problem for dams situated within an urban or agricultural catchment. This can negatively affect the hydro ecosystem, drinking, recreational and other uses of water. In this study, the drinking water quality class of the Roodeplaat Dam, South Africa which faces pollution problems was modeled using machine learning algorisms in Python Jupyter Notebook 6.0.0. Eleven monthly water quality parameters recorded at five sampling stations from January 1981 to September 2017 were used for training and testing the model. Five machine learning classifiers: Gaussian Naïve Bayes (GNB), K-nearest neighbors (KNN), Decision Tree (DT), Support Vector Machines (SVM), and Linear Regression (LR) at a test size of 20%, 25%, 30%, and 40% were used to classify water into five classes (Excellent to Very bad). It was investigated that the dam water has only three classes good, medium, and bad. The prediction accuracies of machine learning algorithms from the highest to the lowest were 96.39%, 96.17%, 92.25%, 90.20, and 54.19% for KNN, DT, SVM, GNB, and LR, respectively. Therefore, KNN at a test size of 30% was recommended to classify the water quality of Roodeplat Dam accurately. Hence, machine learning algorithms can be used to identify the class of water quality before the water is treated and distributed for drinking use.

For embankment slope stability, soil cohesivity is one of the most important shear strength parameters. The effect of cohesiveness on the slope stability of a homogeneous embankment dam under rapid drawdown loading conditions was examined in this study. With the use of numerical modeling in GeoStudio, different situations were explored based on cohesiveness (0 kN/m², 5 kN/m², 10 kN/m^2, and 15 kN/m²) under a 1 m per day drawdown rate. The factor of safety value obtained from the long-term steady-state condition under 15 kN/m² cohesion was equivalent to a 116.8% increase from the one obtained under 0 kN/m² cohesion. The factor of safety values obtained after subjecting the embankment to different soil cohesion levels yielded a p-value of 1.91 x 10^-41, according to the Analysis of Variance. The calculated p-value (alpha value) is less than 0.05, suggesting that the differences between the examined cohesiveness values based on the list of the factor of safety values are statistically significant. The findings derived in this study show that it is significant to capture the effect of material characteristics during the design phase of an embankment dam.

Recently, torrential rain and drought have occurred in close temporal proximity and for similar durations due to changes in the spatiotemporal patterns of rainfall owing to climate change. In particular, when a drought occurs, it tends to be prolonged, making it necessary to improve the operation of multi-purpose dams that not only control flooding but also serve as water supplies. In this study, standard water volume lines and action plans by response stage were improved so that water could be stored in advance of a drought instead of reservoir operation criteria set based on data from the past. The minimum water demand by use (domestic water, industrial water, and agricultural water) was also calculated. The improved reservoir operation criteria were applied to multi-purpose dams in the Nakdong River Basin, and their effects were analyzed by calculating additionally secured water volumes. In the future, in case of lowered water volumes in multi-purpose dams owing to a drought, the application of these improved reservoir operation criteria is expected to contribute to water supply stability by delaying entry into the drought stage, and minimizing the damages caused by limited water supplies.

Background: Poor patient flow can lead to adverse outcomes for patients and organisational inefficiency. Many hospitals have addressed suboptimal patient flow by increasing resourcing, such as bed stock and staffing, however, this is an unsustainable approach. In determining the nature of poor patient flow issues, it is important to collect data from healthcare professionals who manage patient flow on a daily basis. Doing so provides insights into the current state of patient flow management in its entirety, whilst also helping with the development of sustainable solutions.; Methods: Thirteen semi-structured interviews were conducted with clinicians who were directly involved with patient flow at a tertiary care centre in Tasmania, Australia. Results: Through a thematic analysis method, four major themes were developed: managing patient flow, communication for decisions, tools as enablers and barriers and increasing complexity. Conclusions: The findings of this study provide great insights into patient flow issues, with potential solutions identified to address them.

Depletion of ore deposits, increasing demand for raw materials, the need to process low-grade, complex and finely disseminated ores and the reprocessing of tailings are challenges, especially for froth flotation separation technologies. Even though capable of handling relatively fine grain sizes the flotation separation of very fine and ultrafine particles faces many problems still. Further, the flotation of low-contrast semi-soluble salt-type minerals with very similar surface properties, many complex interactions between minerals, reagents and dissolved species often result in poor selectivity. This study investigates the flotation beneficiation of ultrafine magnesite rich in dolomite from de-sliming, currently reported to the tailings. The paper especially focuses on the impact of the depressant sodium hexametaphosphate (SHMP) on: (i) the froth properties using dynamic froth analysis (DFA), (ii) the separation between magnesite and dolomite/calcite and (iii) its effect on the entrainment. Furthermore, the application of 1-hydroxyethylene-1,1-diphosphonic acid (HEDP) is a more environmentally friendly and low-cost alternative to SHMP is presented and discussed. The paper contributes to understanding on the complexity of depressant responses in froth flotation.

Legacy mining industry has left a large number of tailings ponds exposed to water and wind erosion that causes serious environmental and health problems. Prior to rehabilitation actions a deep sampling of the materials infilling the pond used to be necessary. Thus, the primary objective of this study is to demonstrate the usefulness of the Electrical Resistivity Tomography (ERT) method as a non-invasive tool to determine the physicochemical composition of mine tailings ponds, enabling more efficient and low-cost surveys. To achieve this objective, three ERT profiles and three boreholes in each profile were carried out, from each borehole three waste samples from differents depths were collected and a geochemical characterization of the samples was carried. In order to estimate the composition of the infilling wastes in tailing ponds from electrical resistivity measures, several regression models were calculated for different physicochemical properties and metal concentrations. As a result, a high resistivity area was depicted in profiles G2 and G3 while a non-resistive area (profile G1) was also found. Relationships among low resistivity values and high salinity, clay content and high metal concentrations and mobility were established. Specifically, calibrated models were obtained for electrical conductivity, particles sizes of 0.02-50 µm and 50-2000 µm, total Zn and Cd concentration, and bioavailable Ni, Cd and Fe. Therefore, the ERT technique could be considered as a useful tool for mine tailings ponds characterization, and it can be used to estmate some physicochemical properties and metal concentrations of this mine waste.

Advanced-Differential Interferometric SAR (A-DInSAR) has been used to monitor surface deformations in open pit mines and tailings dams. In this paper, ground deformations have been detected on the area of the tailings Dam-I at the Córrego do Feijão Mine (Brumadinho, Brazil) before its catastrophic failure occurred on 25 January 2019. Two techniques optimized for different scattering models, SBAS (Small BAseline Subset) and PSI (Persistent Scatterer Interferometry), were used to perform the analysis based on 26 Sentinel-1B images in IW mode, acquired on descending orbits from 03 March 2018 to 22 January 2019. A WorldDEM DSM product was used to remove the topographic phase component. The results provided by both techniques showed a synoptic and informative view of the deformation process affecting the study area, with a detection of persistent trend of deformations on the top, middle and bottom sectors of the dam face until its collapse, as well as the expected natural settlements on the tailings. It is worth noting the detection of an acceleration in the displacement time-series for a short period near the failure. The maximum accumulated displacements detected along the downstream slope face were -39 mm (SBAS) and -48 mm (PSI). It is reasonable to consider that Sentinel-1 would provide decision makers complementary motion information to the in-situ monitoring system for risk assessment and for a better understanding of on-going instability phenomena affecting the tailings dam.

The biodegradability of water hyacinth for biogas and biofertiliser production was studied under mesophilic conditions. The effects of water hyacinth pre-treatments were also included in this investigation. It was found that water hyacinth has a low biodegradability of 27% when monodigested while at a 3:1 ratio with cow manure, the biodegradability increases to 46%. At this elevated biodegradability, the water hyacinth biomethane potential was 185 LCH4/kgVS, while that of cow manure was 216 LCH4/kgVS. The Gompertz kinetic model had superior parameters than the Logistic model for most of the water hyacinth-cow manure combined substrate digestion. Based on the Gompertz model, the lag phase and daily maximum methane production rate were 5.5 days and 22.9 ml /day respectively for the 3:1 codigestion (R2 of 0.99). These values were 6.7 days and 15.2 ml/day respectively, in the case of water hyacinth monodigestion (R2 = 0.996). The dominant microbial species detected in the digestates were Bacteroidetes and Proteobacteria. A few microbial species were indigenous to water hyacinth but a more diverse consortia which is key to efficient substrate biodegradation, came from cow manure. The digestate contained ammonium nitrogen at 68 mg/kg with phosphorous and potassium at 73 and 424 mg/kg respectively. Nitrogen was lower but phosphorous and pottasium were comparable to previously studied digestates of other substrates. Only water hyacinth pretreated through aerobic composting proved to unlock a higher methane yield that matched a 3:1 codigestion with cow manure. Other pretreatments induced better biodegradation performance than that observed on untreated water hyacinth but this improvements were not as good as that of the 3:1 codigestion scheme. It was concluded that water hyacinth sourced from the Hartbeespoort dam, could be treated through anaerobic digestion to recover biogas and biofertilizer. However, more experiments are required to fully understand and harness the optimisation opportunities available in applying this technology to manage water hyacinth.

The implementation of phytoremediation strategies under arid and semi-arid climate requires the use of appropriate plant species capable of withstanding multiple abiotic stresses. In this study, we assessed the combined effects of organo-mineral amendments and microbial inoculants on chemical and biological properties of mine tailings, as well as on growth of native plant species under drought stress conditions. Plants were cultivated in pots containing 1 kg of a mixture of mine tailings and topsoil (i.e. pre-mined superficial soil) in a 60:40 ratio, 6% marble sludge and 10% sheep manure. Moreover, a consortium of four drought-resistant rhizobacteria was inoculated. Three irrigation levels were applied: well-watered, moderate water deficit, and severe water deficit, corresponding to 80%, 45%, and 30% of field capacity, respectively. The addition of topsoil and organo-mineral amendments to mine tailings significantly improved their chemical and biological properties, which were further enhanced by bacterial inoculation and plants’ establishment. Water stress negatively impacted enzymatic activities in amended tailings, resulting in a significant decrease of acid and alkaline phosphatases, urease, and dehydrogenase activities. Similar results were obtained for bacteria, fungi and actinomycetes abundance. PGPR inoculation positively influenced the availability of phosphorus, total nitrogen, and organic carbon, while increased alkaline phosphatase, urease (by about 10%) and dehydrogenase activities (by 50%). The rhizosphere of P. harmala showed the highest enzymatic activity and number of culturable microorganisms, especially in inoculated treatments. Severe water deficit has nega-tively affected plant growth, leading to a 40% reduction in shoot biomass of both Atriplex halimus and Pennisetum setaceum compared to well-watered plants. Peganum harmala showed greater tolerance to water stress, as corroborated by the lower decreases observed in root and shoot length and dry weight compared to well-watered plants. The use of bioinoculants mitigated the negative effects of drought on P. harmala shoot biomass, resulting in an increase of up to 75% in the aerial biomass in plants exposed to severe water deficit. In conclusion, the results suggest that the combination of organo-mineral amendments, PGPR inoculation and P. harmala represents a promising approach to enhance the phytoremediation of metal-polluted soils under semi-arid conditions.

The deformation monitoring information of concrete dams contains some high-frequency com-ponents, and the high-frequency components are strongly nonlinear, which reduces the accuracy of dam deformation prediction. In order to solve such problems, this paper proposes a concrete dam deformation monitoring model based on empirical mode decomposition (EMD) combined with wavelet threshold noise reduction and sparrow search algorithm (SSA) optimization of long short-term memory network (LSTM). The model uses EMD combined with wavelet threshold to decompose and denoise the measured deformation data. On this basis, the LSTM model based on SSA optimization is used to mine the nonlinear function relationship between the reconstructed monitoring data and various influencing factors. The example analysis shows that the model has good calculation speed, fitting and prediction accuracy and it can effectively mine the date char-acteristics inherent in the measured deformation, and reduce the influence of noise components on the modeling accuracy.

Cymbidium goeringii, locally known as the spring orchid in Korea, is one of the most important and popular horticultural species in the family Orchidaceae. C. goeringii cultivars were originated from plants with rare phenotypes in wild mountains where pine trees commonly grow. This study aimed to determine the cultivar-specific combined genotypes (CGs) of short sequence repeats (SSRs) by analyzing multiple samples per cultivar of C. goeringii. In this study, we collected more than 4,000 samples from 67 cultivars and determined the genotypes of 12 SSRs. Based on the most frequent combined genotypes (CG1s), the average observed allele number and combined matching probability were 11.8 per marker and 3.118×10-11, respectively. Frequencies of the CG1 in 50 cultivars (n ≥ 10) ranged from 40.9% to 100.0%, with an average of 70.1%. Assuming that individuals with the CG1 are genuine in the corresponding cultivars, approximately 30% of C. goeringii on the farms and markets may be not genuine. The dendrogram of the phylogenetic tree and principal coordinate analysis largely divided the cultivars into three groups according to their countries of origin; however, the genetic distances were not distant among the cultivars. In conclusion, this dataset of C. goeringii cultivar-specific SSR profiles could be used for ecogenetic studies and forensic authentication. This study suggests that genetic authentication should be introduced for the sale of expensive C. goeringii cultivars. We believe that this study will help establish a genetic method for the forensic authentication of C. goeringii cultivars.

The growth of demand for metallic minerals has faced with the need for new techniques and improving technologies for all mine life cycle operations. Nowadays, the exploitation of old tailings and mine wastes facilities could represent a solution to this demand, with economic and environmental advantages. W-Sn Panasqueira Mine has been operating for more than 100 years. Its first processing plant “Rio” was located near Zêrere river being the mineral processing residues deposited on the top hillside on the margin of this river in Cabeço do Pião tailings dam. The lack of maintenance and monitoring of this enormous structure in the last twenty years represents high risks to the environment and population of the surrounding region. The re-mining of the tailings by hydrometallurgical methods was considered, in order to satisfy these two enounced conditions - metals demand and environmental risk, aiming for the sale of the metal to pay the environmental intervention. Field samples campaign allowed collecting data and results from laboratory tests driving to use regression optimization. The re-mining solution was studied, taking into account the technical, economic, social, and environmental aspects.

The assessment of ecosystem quality and the maintenance of optimal ecosystem function requires understanding vegetation area dynamics and its relationship with climate variables. This study aims to detect vegetation area changes over a downstream dam and to understand the influence of the dam as well as climatic variables on the region’s vegetation areas. The case study is located in an arid area with an average rainfall amount of 50 to 100 mm/year. An analysis of seasonal changes in vegetation areas was conducted using the Normalized Difference Vegetation Index (NDVI), and supervised image classification was used to evaluate changes in vegetation areas using Landsat imagery. Pearson correlation and multivariate linear regression were used to assess the response of local vegetation areas to both hydrologic changes due to dam construction and climate variability. The NDVI analysis reveals a considerable vegetation decline after the dam construction in the dry season. This is primarily associated with the impoundment of the seasonal water by the dam and the increase in cropland areas due to dam irrigation. A significantly stronger correlation between vegetation changes and precipitation and temperature variations is observed before the dam construction. Furthermore, multivariant linear regression was used to evaluate the variations of equivalent water thickness (EWT), climate data, and NDVI before and after the dam construction. The results suggest that 85 percent of the variability in the mean NDVI was driven by climate variables and EWT before the dam construction. On the other hand, it was found that only 42 percent of the variations in NDVI were driven by climate variables and EWT after the dam construction for both dry and wet seasons.

Rapid draw-down in an earthfill dam has serious implications for dam safety regarding slope stability. The evaluation of reservoir draw-down impact on slope stability was carried out considering the case study of 8 hours of rapid draw-down of the Middle Marsyangdi Hydroelectric Power Project (MMHPP) rock-fill dam using the Limit Equilibrium Method (LEM) and stress-based Finite Element Method (FEM). The time-dependent factor of safety (FOS) was evaluated and found that the 8 hours of rapid draw-down undertaken in October 2012 for reservoir flushing was unsafe with a draw-down rate of 1.91m/h. The resulting FOS of 1.28 and 1.27 using LEM and FEM was classified as unsafe as per the US Army Corps of Engineers’ guideline, the minimum required factors of safety should be greater than 1.3. The minimum safe allowable draw-down rate of 0.76m/h for 20 hours was identified. Applying three layers of horizontal filter materials and increasing the upstream dam’s permeability provided adequate FOS results for all cases by increasing seepage discharge to reduce the destabilizing excess pore water pressure. Several gradual draw-down rates were also tested and found that FOS increases with decreased draw-down rates, as it reduces the excess pore water pressure controlled with stabilizing existing water load.

Sediment accumulation in a dam reservoir is a common happening environmental problem throughout the world. Topographic conditions, land use land cover change, the intensity of rainfall, and the soil characteristics are the major driving factors for sedimentation to occur. The effect of sedimentation in a dam reservoir is very visible in the watershed as a result of hilly topographic conditions, high rainfall intensity, thin land cover, and less soil infiltration capacity. In this paper, an integrated RUSLE and GIS technique was implemented to estimate a mean annual sediment yield based on spatial and temporal variations in Nashe dam reservoir situated in Fincha catchment, Abaya River basin, Ethiopia. Spatial and temporal estimation of mean annual sediment yield was estimated using the Revised Universal Soil Loss Equation (RUSLE) model and GIS. Historical 6-year (2014-2019) rainfall for the temporal variations and other physical factors such as soil erodibility, slope and length steepness, management and land used land cover, and support practice for spatial variations were used as sediment driving factors. The mean annual sediment yield ranges from 0 to 2712.65 t ha-1 year-1 was seen. Spatially, Very high, high, moderate, low, and very low sediment yield severity with total area coverage with 25%, 10%, 30%, 15%, and 20% in 2017, 2015, 2019, 2014, and 2018 respectively. The information about the spatial and temporal variations of the severity of sediment yield in RUSLE model has a paramount role to control the entry of sediment into the dam reservoir in this watershed. The results of the RUSLE model can also be further considered along with the watershed for planning strategies for dam reservoirs in the catchment.

In this work, a deep characterization of the properties of K6Ta10.8O30 microrods has been performed. The starting material used to grow the microrods has been recovered from mining tailings coming from the Penouta Sn-Ta-Nb deposit, located in the north of Spain. The recovered material has been submitted to a thermal treatment to grow the microrods. Then, they have been characterized by scanning electron microscopy, X-ray diffraction, micro-Raman and micro-photoluminescence. The results of our study confirm that the K6Ta10.8O30 microrods have a tetragonal tungsten bronze-like crystal structure, which can be useful for ion-batteries and photocatalysis.

Attention-deficit/hyperactivity disorder (ADHD) is a common neurodevelopmental disorder. Given the growing evidence of gut microbiota being involved in psychiatric (including neurodevelopmental) disorders, we aimed to identify differences in gut microbiota composition between participants with ADHD and controls and to investigate the role of the microbiota in inattention and hyperactivity/impulsivity. Fecal samples were collected from 107 participants (NADHD=42; Ncontrols=50; NsubthreholdADHD=15; range age: 13-29 years). The relative quantification of bacterial taxa was done using 16S ribosomal RNA gene amplicon sequencing. Beta-diversity revealed significant differences in bacterial composition between participants with ADHD and healthy controls, which was also significant for inattention, but showing a trend in case of hyperactivity/impulsivity only. Ten genera showed nominal differences (P < 0.05) between both groups, of which seven genera were tested for their association with ADHD symptom scores (adjusting for age, sex, body mass index, time delay between feces collection and symptoms assessment, medication use and family relatedness). Our results show that variation of a genus from the Ruminococcaceae family (Ruminococcaceae_UCG_004) is associated (after multiple testing correction) with inattention symptoms, and suggest a role of gut microbiota in ADHD pathophysiology.

The application of multiple criteria decision-making (MCDM) techniques in real-life problems has increased in recent years. The need to build advanced decision models with higher capabilities that can support decision making in a broad spectrum of applications, promotes the integration of MCDM techniques with applicable systems, including artificial intelligence, and Geographic Information Systems (GIS). The Analytic Hierarchy Process (AHP) and Technique for Order of Preference by Similarity to Ideal Solution (TOPSIS) are amongst the most widely adopted MCDM techniques capable of resolving water resources challenges. A critical problem associated with water resource management is dam site selection. This paper presents a comparative analysis of TOPSIS and AHP in the context of decision making using GIS for dam site selection. The comparison was made based on geographic and water quality criteria. A ratio estimation procedure was used to determine the weights of these criteria. Both methods were applied for selection of optimal sites for dams in the Sistan and Baluchestan province, Iran. The results show that the TOPSIS method is better suited to the problem of dam site selection for this case study. Actual locations of dams constructed in the area were used to verify the results of both methods.

One source of kaolinite-rich wastes is from mine tailings and the generation of enormous volumes of mine tailings waste is standard practice in this industry. These volumes of waste are, at present, dumped, provoking significant environmental impact and transforming the environment. The impact of storing coal waste requires the study of eco-innovative solutions for the assessment of waste types. The present investigation has the objective of expanding the knowledge on the behavior of new siliceous-aluminum minerals with pozzolanic activity, of added value in the manufacture of similar cements. Four samples were characterized to determine their chemical, morphological and mineralogical composition. The samples were subjected to different thermal activation conditions for the transformation of an inert waste into a material with cementitious properties. XRD analysis have confirmed the total transformation of kaolinite into metakaolinite. The results have shown that after the activation process, the coal refuse presented good pozzolanic activity, meaning that it may be used as a pozzolanic addition in industrial cements, thereby removing high levels of contaminated waste from the environment. In subsequent investigations, research work will continue with the replication of cements with this pozzolanic addition for use in the manufacture of sleepers and slab track railway system.

The problem of limited water supply in the Vhembe District (Limpopo Province, South Africa) is exacerbated by a preponderance of dissolved salts, which cause disagreeable taste and odour in the water as reported by the communities using this water for drinking. The water treatment plant that supplies the treated water to the communities in the District sources this raw water from the Nandoni Dam at the Livhuvu river catchment. However, there are no scientific studies that have been reported in the literature which focused on determining the levels of water salinity from various water sources in the municipalities of the District. Water samples from various sites across the Nandoni Dam, a primary source of domestic water supply in the region, were collected during all the seasons basis over a period of twelve months in order to ascertain the concentrations of dissolved salts in the dam. Onsite analyses of the water samples were conducted using the YSI ProDSS multimeter, while the laboratory water analyses were conducted using the spectroquant and atomic absorption spectrometers. Although salinity tests seem to indicate that the water sampled across most of the Nandoni Dam is brackish during all seasons of the year with the highest being 750 mg/L, water samples from the dam mid-outlet and the treatment plant are slightly below the WHO brackish water bracket of 500 mg/L with unfavourable taste for drinking. Results from this study indicate that the water sourced from the Nandoni Dam is not suitable for human consumption and therefore requires integrated water resource management, as well as robust and cost-effective water desalination treatment.

The Vaal Dam catchment, which is the source of potable water for Gauteng province, holds various human activities including mining, urbanization, agricultural and industrial activities coupled with high fluxes of nutrients from different areas within the catchment. This situation led to an enhancement of Harmful Algal Blooms (HABs) in the dam reservoir. Phosphorus and Nitrogen are the limiting nutrients for HABs in many eutrophic aquatic systems when their concentrations are raised in such waters. In this study, multi-time-series plot types and scutter plots were analysed to reveal the relationship between HABs proxy chlorophyll-a (Chl-a) and the potential nutrients. Also (Chl-a) data extracted from landsat-8 satellite images were visualised to show the spatial distribution of HABs in the reservoir. The results showed that the Vaal Dam HABs productivity is a function of the total phosphorus (TP) and the organic nitrogen (KJEL_N) levels, which were positively correlated with chlorophyll-a (Chl-a) concentration. The long-term analysis of Chl-a in-situ data (1986 – 2022) measured at one point within the reservoir showed an average of 11.25μg/l but at some stochastic dates, the Chl-a concentration jumped to very high values reaching the maximum value of 452.8μg/l. Such high values are associated with high records of TP and KJEL_N concentrations at the same dates which clearly reveals their effect on the productivity levels. The decadal time series and its trend analysis showed that the average productivity level of Chl-a increased during the studded period from 4.75μg/l in the first decade (1990 – 2000) to 10.51μg/l in the second decade (2000 – 2010) reaching 16.7 during the last decade (2010 – 2020). The increasing averages of the decadal values are associated with the increasing decadal average of its driving factors, TP from 0.1043 to 0.1096 to 0.1119mg/l for the three decades, respectively and KJEL_N from 0.80mg/l in the first decade to 1.14mg/l in the last decade. The decadal average of temperature showed no significant increase, 17.9 °C in the first decade and 18 °C in the last decade which suggests that temperature is not the only enhancing factor of the HABs productivity in the Vaal Dam. The satellite data analysis during the last decade revealed that the HABs spatial dynamics is a function of the dam geometry and the levels of the discharges from its two feeding rivers. Higher concentrations were observed where the reservoir is meandering and within the areas of restricted water circulation.

The Grand Ethiopian Renaissance Dam (GERD), formerly known as the Millennium Dam, is currently under construction and has been filling at a fast rate without sufficient known analysis on possible impacts on the body of the structure. The filling of GERD not only has an impact on the Blue Nile Basin hydrology, water storages and flow but also pose massive risks in case of collapse. Rosaries Dam located in Sudan at only 116 km downstream of GERD, along with the 20 million Sudanese benefiting from that dam, would be seriously threatened in case of the collapse of GERD. In this study, through the analysis of Sentinal-1 satellite imagery we show concerning deformation patterns associated with different sections of the GERD’s Main Dam (structure RCC Dam type) and the Saddle Dam (Embankment Dam type). We processed 109 descending mode scenes from Sentinel-1 SAR imagery, from December 2016 to July 2021, using the Differential Synthetic Aperture Radar Interferometry technique to demonstrate the deformation trends of both - the GERD’s Main and Saddle Dams. The time-series generated from the analysis clearly indicates different displacement trends at various sections of the GERD as well as the Saddle Dam. Results of the multi temporal data analysis on and around the project area show inconsistent subsidence at the extremities of the GERD Main Dam, especially the west side of the dam where we recorded varying displacements in the range of 10 mm to 90 mm at the crest of the dam. We conducted the current analysis after masking the images with a coherence value of 0.9 and hence, the subsequent results are extremely reliable and accurate. Further decomposition of the subsiding rate has revealed higher vertical displacement over the west side of the GERD’s Main Dam as compared to the east side. The local geological structures consisting of weak zones under the GERD’s accompanying Saddle Dam adds further instability to its structure. We identified seven critical nodes on the Saddle Dam that match the tectonic faults lying underneath it, and which display a varying degree of vertical displacements. In fact, the nodes located next to each other displayed varying displacement trends: one or more nodes displayed subsidence since 2017 while the other node in the same section displayed uplift. The geological weak zones underneath and the weight of the Saddle Dam itself may somewhat explain this inconsistency and the non-uniform vertical displacements. For the most affected cells, we observed a total displacement value of ~90 mm during the whole study period (~20 mm/year) for the Main Dam while the value of the total displacement for the Saddle dam is ~380 mm during the same period (~85 mm/year). Analysis through CoastSat tool also suggested a non-uniformity in trends of surface water-edge at the two extremities of the Main Dam.

Osteoporosis is an abnormal bone remodeling condition characterized by decreased bone density, which leads to high risks of broken bones. Previous studies have demonstrated that Lycii Radicis Cortex (LRC) extract inhibits bone loss in ovariectomized (OVX) mice by enhancing the osteoblast differentiation. A bioactive compound, Kukoamine B (KB), was identified from a fractionation of LRC extract as a candidate component responsible for an anti-osteoporotic effect. This study investigated the anti-osteoporotic effects of KB using in vitro and in vivo osteoporosis models. KB treatment significantly increased the osteoblastic differentiation and mineralized nodule formation of osteoblastic MC3T3-E1 cells, while it significantly decreased the osteoclast differentiation of primary-cultured monocytes derived from mouse bone marrow. The effects of KB on osteoblastic and osteoclastic differentiations under more physiological conditions were also examined. In the co-culture of MC3T3-E1 cells and monocytes, KB promoted osteoblast differentiation but did not affect osteoclast differentiation. For the in vivo experiments, KB significantly inhibited OVX-induced bone mineral density loss and restored the impaired bone structural properties in osteoporosis model mice. These results suggest that KB may be a potential therapeutic candidate for the treatment of osteoporosis.

This study aims to contribute to the characterization of Katangese Copperbelt's mining wastes and soils polluted with trace metals, using pollution indices and direct concentration measurements. The study also evaluated the use of these indices in assessing the success of remediation projects. Analytical data from previous studies and samples collected from six types of discharge and one polluted soil were used to address the first objective. Soil and plant samples were collected at Kipushi and Penga Penga for the second objective. The results revealed very high concentrations of As, Cd, Co, Cu, Mn, Pb, and Zn in all mine tailings and polluted soils, compared with local references. The degree of contamination (DC) values (from 72 to 5440) and potential ecological risk (RI) values (from 549 to 162 091) indicate very high-risk situations associated with polluted discharges and soils. Regarding revegetation trials, the results show lower concentrations and RIs in tree rhizospheres compared with unamended areas at both sites. However, trace metal concentrations are higher in tree rhizospheres compared with local references, and RI values are in the considerable risk range for Penga Penga (RI = 533) and very high (&gt;1500) for Kipushi. Bioconcentration factor values are below 1, indicating low accumulation in roots, wood, and leaves, and low risk of contamination of the trophic chain. In this context, it seems that the pollution indices used are unsuitable for assessing the effectiveness of phytotechnology processes based on metal stabilization. Direct plant performance measurements combined with direct measurements of metals in substrates and plants to assess transfer and efficiency are more appropriate.

The paper focuses on the application of a multilevel, integrative and territorial approach to the protection of cultural heritage through planning instruments in Serbia. It points out the problems of the sectoral approach and discusses international recommendations that can be integrated into the planning methodology. The case study is the area of Djerdap National Park, which has an already established international and national importance. The research suggests that the cultural heritage in the area, with the exception of the Roman limes, is still recognized at the level of individual localities. The study emphasizes the importance of aligning all levels of governance to safeguard the whole spatial entity rather than focusing solely on its particular areas. The interna-tional and national importance of the planning area contributes to the strengthening of awareness of heritage and its institutional protection. However, the vitality of the area, which is key to its sustainable development, comes from the local level. Planning documents contribute to the inte-gration of local values and local communities into development programs and projects.

Glycosidic linkage analysis was conducted on the unfractionated polysaccharides in the alcohol-insoluble residues (AIRs) prepared from six red seaweeds (Gracilariopsis sp., Prionitis sp., Mastocarpus papillatus, Callophyllis sp., Mazzaella splendens, and Palmaria palmata) using GC-MS/FID analysis of partially methylated alditol acetates (PMAAs). The cell walls of P. palmata primarily contained mixed-linkage xylans and small amounts of sulfated galactans and cellulose. In contrast, the unfractionated polysaccharides of the other five species were rich in galactans displaying diverse 3,6-anhydro-galactose and galactose linkages with varied sulfation patterns. Different levels of cellulose were also observed. This glycosidic linkage method offers advantages for cellulose analysis over traditional monosaccharide analysis that is known for underrepresenting glucose in crystalline cellulose. Relative linkage compositions calculated from GC-MS and GC-FID measurements showed that anhydro sugar linkages generated more response in the latter detection method. This improved linkage workflow presents a useful tool for studying polysaccharide structural variations across red seaweed species. Furthermore, for the first time, relative linkage compositions from GC-MS and GC-FID measurements, along with normalized FID and total ion current (TIC) chromatograms without peak assignments, were analyzed using principal component analysis (PCA) as a proof-of-concept demonstration of the technique's potential to differentiate various red seaweed species.

Background: Educating college students about the importance of good sleep habits could lead to the adoption of healthier sleep routines, including sufficient sleep duration and sleep quality. The current pre-post study examines the impact of completing a sleep education program called “Sleep 101” on (1) sleep hygiene practices, (2) sleep quality, and (3) weekday and weekend sleep behaviors among college students. “Sleep 101” is an interactive online course developed to educate college students about the importance of sleep by addressing basic sleep physiology, the impact of sleep on mood, academic and physical performance, the interactions between sleep and various substances, and common sleep disorders. Methods: 338 college students were recruited from a midsized public university in the US and invited to participate in “Sleep 101”, of which 25 participants completed the baseline and post-intervention questionnaire. The Sleep Hygiene Index (SHI) was utilized to evaluate sleep hygiene practices, while standard questions were employed to assess weekday and weekend sleep behaviors and overall sleep quality. Results: Those who completed the study demonstrated a significant increase in weekday sleep duration and were less likely to engage in negative prior bedtime activities. In addition, 40% of those who completed baseline and post-intervention assessments noticed improvements in their sleep quality. Conclusion: These findings suggest that a brief online program is beneficial in improving sleep behaviors among college and could be a scalable approach to addressing current sleep issues and preventing future sleep problems in college students.

The profile of secondary metabolites occurring in apple cuticular layer is not only characteristic for particular apple cultivar, but also dynamically reflects various external factors in growing environment. In this study, the possibility to authenticate apple samples based on analysis of their cuticular layer extracts was investigated. Ultra-high-performance liquid chromatography coupled to high resolution tandem mass spectrometry (UHPLC-HRMS/MS) was employed for obtaining metabolomic fingerprints. In total, 274 authentic apple samples, four cultivars harvested within the seasons 2020 to 2022 in the Czech Republic and Poland were analysed. The generated complex data processed by univariate and multivariate statistical methods enabled to build classification models for discrimination of apple cultivars as well as their geographical origin. The models showed very good performance in differentiation of Czech and Polish samples for three of four cultivars: ‘Gala’, ‘Golden Delicious’ and ‘Idared’, moreover, the validity of the models was verified over harvest seasons. The diagnostic markers, besides metabolites of triterpene biosynthetic pathway, mainly represented wax esters. ‘Jonagold’, which is known to be susceptible to mutations, was the only cultivar for which the unambiguous classification of geographical origin was not possible.

Strawberry root rot caused by Neopestalotiopsis clavispora is one of the main diseases of strawberry and significantly impacts the yield and quality of strawberry fruit. There are now no effective control techniques available except for fungicide sprays, which may directly impact consumers. Biological control is becoming an alternative method for the control of plant diseases to replace or decrease the application of traditional synthetic chemical fungicides. Trichoderma is widely used as a biological agent for controlling strawberry root rot. In order to provide resources for screening the highly effective biocontrol fungus for controlling strawberry root rot caused by Neopestalotiopsis clavispora, the biocontrol mechanism,the control effects of Trichoderma asperellum CMT10 against strawberry root rot and growth-promoting effects on strawberry seedlings were investigated by plate culture, microscopy observation and root drenching methods.The results showed that CMT10 had obvious competitive, antibiotic and hyperparasitism effects on Neopestalotiopsis clavispora CMGF3. The CMT10 could quickly occupy nutritional space, and the inhibition rates of CMT10 against CMGF3 in confrontation culture on 7 d was 65.49%. The inhibition rates of volatile metabolite and fermentation metabolite produced by CMT10 against CMGF3 were 79.67% and 69.84%, respectively. The mycelium of strain CMT10 can act as hyperparasites by making contacting, winding and penetrating hyphae of CMGF3. Pot experiment showed that the biocontrol efficacy of CMT10 on strawberry root rot caused by Neopestalotiopsis clavispora was 63.00%. CMT10 had obvious promotion effect on strawberry growth, the plant height, root length, total fresh weight, root fresh weight, stem fresh weight and root dry weight, with the promotion rates were 20.09%, 22.39%, 87.11%, 101.58%, 79.82% and 72.33%, respectively. Overall, this study showed the ability of Trichoderma asperellum CMT10 to control strawberry root rot and their potential to develop as novel biocontrol agents to replace chemical fungicides for eco-friendly, sustainable agriculture.

Apis mellifera, especially weak ones, are highly vulnerable to Carpoglyphus lactis mites, which can rapidly infest and consume stored pollen, leading to weakened colonies and potentially colony collapse. This study aimed to ascertain and investigate the prevalence of this mite in honeybee colonies across 9 provinces in the Republic of Korea (ROK). A total of 615 honeybee colonies were collected, from 66 apiaries during the spring and 58 apiaries during the summer of 2023. A 1,242 bp segment of the the Cytochrome c oxidase subunit 1 (COI) gene was amplified using the polymerase chain reaction method. The detection levels of C. lactis in the honeybees were compared between winter and summer. Based on the COI sequence analysis, the nucleotide sequence similarity of C. lactis mites isolated in the ROK with those from China (NC048990.1) was found to be 99.5%, and with those from the United Kingdom (KY922482.1) was 99.3%. This study is the first report of C. lactis in Korean apiaries. The findings in this study demonstrate a significantly higher detection rate in winter, which is 4.1 times greater than that in summer (p &lt; 0.001). Furthermore, the results underscore the usefulness of molecular diagnostic techniques for detecting C. lactis mites.

COX II containing a dual core CuA active site is one of the three core subunits of mitochondrial Cco, which plays a significant role in the physiological process. In this report, the full-length cDNA of COXⅡ gene was cloned from Sitophilus zeamais, which had an ORF of 684 bp encoding 227 amino acids residues. The predicted COXⅡ protein had a molecular mass of 26.2 kDa with pI value of 6.37, and multiple sequence alignment and phylogenetic analysis indicated that Sitophilus zeamais COXⅡ had high sequence identity 78.51% with the COXⅡ of other insect species, especially similarity to sitophilus oryzae. This gene was subcloned into the prokaryotic expression vector pET-32a, and induced by IPTG in E.coli Transetta (DE3) expression system. Finally the COXⅡ with 6-His tag was purified using affinity chromatography with Ni²⁺-NTA agarose. WB showed the recombinant COXⅡ was about 44 kD, and the concentration of fusion protein was 50μg/mL. UV-spectrophotometer and infrared spectrometer analysis showed that recombinant COXⅡ could catalyze the oxidation of substrate Cytc, and influenced by AITC. It was found that AITC could form a hydrophobic region with COXⅡ protein via molecular docking, besides, a sulfur atom of AITC structure could form a length of 2.9 Å hydrogen bond with Leu-31. These results will provide valuable information for elucidating the role of COXⅡ in Sitophilus zeamais responses to AITC, meanwhile, it will helpful to carry out a point mutation in AITC binding sites for the future research.

The properties of the annual, semiannual and triennial oscillations (AO, SAO and TO) in the middle atmosphere have been investigated using the TIMED/SABER temperature data. The Lomb-Scargle and wavelet spectra were used to determine the dominant oscillations in the background temperature field. The AO is prominent at the mid-latitudes. The AO amplitudes present an asymmetry between the two Hemispheres, being larger in the mesosphere than in the stratosphere. The SAO dominates the tropical regions, with three amplitude maxima at altitudes of 45, 75, and 85 km. The SAOs in the upper mesosphere (75 km) are out of phase with those in the mesopause (85 km) in the tropical regions, which can generate an enhancement of 11 K at each equinox, contributing to the lower mesospheric inversion layer. The TO is significant in the tropical region, with amplitude being maximum at 35, 45 and 85 km. Result shows that there may be potential interaction by the TO with SAO at 85km at the equator. The relation between ENSO and TO has also been discussed. The ENSO signal may modulate the amplitude of the TO, mainly in the lower stratosphere. The real origin of the TO may lie in the wave-mean-flow interaction.

This paper is focused on typical rural settlements in the Stara Planina Mountain area in Serbia. They are distinguished by their authenticity, identity and character, and they have still not been destroyed by inappropriate development as is the case in some other mountain areas in Serbia, where the effects of urbanization, globalization and homogenization are obvious. Consequently, there is a need to prevent these effects in mountain areas where there is a threat of disbalance between development and the inherited natural and cultural values. The paper starts from several important concepts that relate contemporary approaches to cultural heritage preservation, place morphology and planning future development. The concept definitions from recent documents from related fields are used. These concepts are then applied to the area of Stara Planina Mountain and its rural settlements. The necessity for an integrative approach to planning this area with significant natural and anthropogenic potential is pointed out, including its integration into international programs of sustainable development.

The research reported on this paper was aimed at improving the overall efficiency of a PDO certified artisanal cheese production process. Being a PDO certified foodstuff by the EU, it is considered to have properties and qualities determined by the geographical environment in which is made, with its production taking place in a specific and determined geographical location, in this case the Serra da Estrela region. In that sense, the authors conducted a mapping according to a systemic perspective of the processes involved in the context of manufacturing and distribution of certified Serra da Estrela cheese. Numerous methods were used throughout the process, such as a systemic design analysis, and techniques derived from ethnographic methods, which led to the collection of data in the field and consequently provided the immersion of the researcher in genuine work situations. Critical points were identified and emphasized in the systemic map with the purpose of encouraging initiatives to address and overcome the gaps and inefficiencies detected. The systemic design analysis triggered the development of design work. Observations following an ethnographic approach identified ergonomic risks in cheese making during the process of cutting excess chips, fostering the emergence of musculoskeletal disorders at the wrist. A tool that fits best to the task at hand was developed. A prototype of the new tool enabled collecting feedback from use in the work context, in order to inform product development. The domains of agricultural production and microbiology, considering the specific microorganisms developed trough the ripening process of the cheese, turned out to be aspects of high importance for the issue under focus, contributing to a broader understanding of the ripening process and its risks, simultaneously improving the efficiency and success of cheese production. If it were not for the systemic analysis, which served as a link between the boundaries of distinct domains such as the risk of microorganism contamination, ergonomics, energy efficiency, legislation and regulation policies, transportation challenges and economic viability, approached throughout the research. Simultaneously creating bridges between them, the various problems might not have been detected in the first place, as they are usually addressed in specialized disciplines, predetermined by the restrictions of each specific area of knowledge. As a consequence of the development of this research, which was based on an analysis that sought to establish possible connections between various disciplines and tried to constantly maintain a holistic perspective, making new connections and observing the issues from a new angle, apart from the already established methodologies. All this allowed to lay out the seeds for the development of a plan to tackle the critical points identified by the systemic analysis reported in this paper.

Promoting green development has become an important way to optimize the ecological and economic structure and promote sustainable development. The Yangtze River Economic Belt is an important economic corridor in China, and it remains to be examined whether the implementation of environmental regulations has enhanced the green total factor productivity (GTFP) of cities. This paper calculates the green total factor productivity of 107 cities within the Yangtze River Economic Belt by using the super-efficient SBM model and the GML index with Chinese city panel data from 2007-2019 and measures the intensity of environmental regulations through textual analysis. The bidirectional fixed-effects model constructed in this paper suggests an inverted U-shaped relationship between environmental regulation and GTFP, which is confirmed by a series of robustness tests. Green technology innovation and advanced industrial structure play a mechanism role in this. In regions with lower levels of green technology and industrial structure, the inverted U-shaped relationship between environmental regulation and green total factor productivity is more significant. In addition, the phenomenon of GTFP rising and then falling because of environmental regulation is more obvious in cities in the middle and upper reaches of the Yangtze River and outside the urban agglomerations. Therefore, when formulating environmental regulation policies, it is necessary to balance the relationship between economic development and environmental protection and harmonize the environment and economic development of the entire Yangtze River Basin.

The wetlands in northeastern Bangladesh are home to some of the most prolific and valuable ecosystems on the planet, offering a wide range of benefits to both the local and wider communities. A limited number of research on this topic have been carried out in various wetlands in coastal hilsa, but none have been located in the northeastern region of Bangladesh. Thus, the goal of this study was to better understand the most commercially relevant species (anadromous hilsa) in northeastern Bangladesh as well as to assess the wetland ecosystem services more thoroughly with the contribution of their fish genetic resources. In addition to laboratory studies, fieldwork was done in the fishing settlements along the Surma River, Hakaluki Haor, and Tanguar Haor. The study classified 77 fish species into 21 subcategories of ecosystem services, of which 56% were not threatened, 17% were vulnerable, and 10% were highly endangered. The species Hilsa was found to be the most economically significant, accounting for 1% of the GDP overall. The study determined if the hilsa stock of the examined wetlands maintains a single or several subpopulations in comparison to other parts of the country when they migrate from saline water to northeastern Bangladesh (freshwater). But when compared to other groups, the FST score was between 0.000 to 0.017, indicating that the populations are identical and that there is genetic material sharing between them. Additionally, these statistics imply that the Sylhet haor and adjacent river systems contain a single stock of Hilsa fish. Nevertheless, a number of stresses and risks, including overexploitation, illicit and destructive fishing, siltation, and natural disasters like flash floods, have been linked to changes in the supply of hilsa and other ecosystem services. This study also emphasizes the necessity of policy attention and research to address the concerns.

In this paper, we introduce a specialized, fully automated experimental arrangement designed for assessing the effectiveness of augmented and virtual reality technologies in healthcare setting and explore its design principles focusing on depth sensor characterization. The main goal of this project is to establish a robust benchtop platform for the quantitative evaluation of extended reality technologies in a controlled environment, emphasizing the practical assessment of augmented reality head-mounted devices. We outline a design concept and considerations for an experimental configuration aimed at creating a realistic testing environment. This apparatus comprises an observation platform mounted on a three-degree-of-freedom motorized system and a test phantom stage. Focusing on real-case scenarios, we utilized a range of sensors, including readily available range-sensing cameras and commercial augmented reality headsets, such as the Intel RealSense L515 LiDAR camera, mounted on the motion control system. The setup enabled automated data collection and facilitates controlled assessments and validation of various facets of augmented reality technologies, including object, hand, and head tracking, as well as static and dynamic image registration. This paper describes the system architecture, the process of automated data collection, and presents several evaluation studies conducted with this setup, providing insights into the quality and temporal noise associated with static or moving objects or observers in augmented reality applications.

To conduct high-precision and high-resolution numerical simulation of complex flow structures in turbomachinery, a high-order finite volume weighted essentially non-oscillatory (WENO) scheme for the large eddy simulation (LES) is improved and embedded into the three-dimensional viscous unsteady CFD solver NUAA-Turbo. Firstly, the spectral characteristics and unsteady convergence of the improved WENO scheme are studied. Compared with the classical WENO scheme, the improved WENO scheme has better dissipation and dispersion characteristics and faster convergence speed. Then, the coefficient CW of the Wall-Adapting Local Eddy-viscosity (WALE) model is calibrated by decaying homogeneous isotropic turbulence (DHIT) test case. Finally, the scheme is applied to conduct high-precision LES calculations of turbulent boundary layer flow, supersonic compression corner flow, and low-pressure turbine cascade separation flow. The numerical simulation results show that this WENO scheme has excellent shock wave capture ability and turbulence resolution and can capture more flow field details with less mesh size, greatly reducing the computational cost and laying a foundation for large-scale engineering application of LES.

To secure logic circuits against the illegal copying the insertion of the so-called key bit inputs using XOR/XNOR gates has been proposed in . The inserted gates modify (lock) the behavior of the original circuit and only the correct choice of the secret key bits guarantees the equivalent behaviour of the locked circuit to the original circuit. To break this kind of security, i.e. to find the secret key bits, there was a SAT solver based attack proposed in . The aim of this work is to experimentally verify this attack on several locked circuits with various number of primary inputs and outputs and with various number of gates. Except for the random placement of the key gates we evaluate also the positioning with chaining elimination. The obtained and presented results show that we were able to unlock 10 of 11 circuits within few minutes on a common PC.

Intermetallic compounds are increasingly being expected to utilize in tribological environments, but to date the works are hindered by insufficient ductility at low and medium temperature. This paper presents a novel multiphase intermetallic alloy with the chemical composition of Mo-40Ni-13Si (at.%). Microstructure characterization reveals that a certain amount of ductile Mo phases formed during the solidification process of ternary Mo-Ni-Si alloy melt, which is undoubtedly beneficial to the ductility improvement of intermetallic alloy. Tribological properties of the designed alloy, including wear resistance, friction coefficient and metallic tribological compatibility, were evaluated under dry sliding wear test conditions at room temperature. Results suggested that the multiphase alloy possesses an excellent property for room-temperature wear applications, which is attributed to the unique microstructural features and thereby good combination in hardness and ductility. The corresponding wear mechanism is also reported by observing the worn surface, subsurface and wear debris of alloy, which to be found is soft abrasive wear.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The electroencephalogram (EEG) is a record of brain activity. Brain Computer Interface (BCI) technology formed by the EEG signal has become one of the hotspots at present. How to extract the feature signal of EEG is the most basic research of BCI technology. In this paper, A new method of recognizing fatigue, conscious, concentrated state of human brain is proposed by the combination of discrete wavelet transform and the neural network based on EEG signal. First of all, the law signal is preprocessed by the wavelet denoising method because the law EEG signal contains a large number of high frequency noise, which is decomposed into multi-layer high frequency signal and low frequency signal. thus, δ wave, θ wave, α wave, β wave are obtained by the wavelet transform. And then, frequency band energy of the different wave is regards as the feature signal of EEG. In the experiment, the feature signal is classified by radial basic function (RBF) and annealed chaotic competitive learning network (ACCLN). RBF and ACCLN networks are trained with 500 sets of sample data and are tested by 100 sets of samples in different mental states. The experimental results show that the average accuracy of RBF network under three conditions are 88.75%, 88.25%, 88.5%, respectively, and the correct rate of ACCLN network is 97%, 98%, 98%, respectively.

Early discharge after childbirth has led to a rise in neonatal readmission, becoming a major concern in recent decades. Our research aimed to identify the risk factors and incidence of neonatal readmission, as well as explore preventive measures. Our study at the Clinical Hospital of Pediatrics in Ploiești, Romania included 108 neonates admitted during the neonatal period. This accounted for 2.06% of all admissions (5226). The most prevalent cases were malnutrition (25%), fever (20.3%) and bronchiolitis (17.5%). Diarrhea and infectious gastroenteritis were also observed (14.8%), along with acute rhinoconjunctivitis (9.2%) and late onset sepsis (3.7%). No deaths were recorded. The most significant characteristics identified were number of children (p&lt;0.001) and age at maternity discharge (p&lt;0.001). By following the prevention rules, malnutrition, feeding errors, and infections can be avoided. This includes practicing proper hand hygiene for both mothers and medical staff, as well as educating and demonstrating to mothers the benefits of breastfeeding. In addition, all newborns discharged from the maternity ward should benefit from follow-up at 7-10 days of life. Our results confirm the effectiveness of a multidisciplinary team and endorse promoting breastfeeding. Implementing quality control measures and regularly evaluating the surveillance program will help improve its effectiveness.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

Two interesting compounds such as quaternary ammonium lignin(QAL) and 2-ethylhexyl phosphoric acid mono-2-ethylhexyl ester (P507) were synthesized as ionic liquids(QP-ILs) for the extraction of metal ions. The extraction behavior of Co(II) and Ni(II) from chloride solution was compared between QP-ILs and P507. The results showed that the extraction rates of Co(II) and Ni(II) in the two solutions varied with the extraction conditions, but QP-ILs has stronger extractability for cobalt than P507, while Ni is on the contrary. Under the same conditions, the Co/Ni separation performance(βCo/Ni) in QP-ILs is superior to that in p507. At pH4.0, 55℃, concentration of 20%, extraction time of 10 minutes, the βCo/Ni of QP-ILs reached to 2703, while that of P507 was only 164. In conclusion, QP-ILs was more efficient than P507 for separating Co from mixed solutions.

Brain aging causes a wide variety of changes at molecular and cellular levels, leading to the decline of cognitive functions and increased vulnerability to neurodegenerative disorders. The research aimed at understanding the aging of the brain has made much progress in recent decades. Technological innovations such as single-cell RNA-sequencing (scRNA-seq), proteomic analyses, and spatial transcriptomic analyses have facilitated the research on the dynamic changes occurring within neurons, glia, and other cells along with their impacts on intercellular communication during aging. In this review, we introduce recent trends of how neurons and glia change during aging and discuss the impact of the brain microenvironment such as the blood-brain barrier (BBB).

In this paper, we study the semilinear pseudo-parabolic equations $\displaystyle u_{t} - \triangle_{\mathbb{B}}u - \triangle_{\mathbb{B}}u_{t} = \left|u\right|^{p-1}u$ on a manifold with conical singularity, where $\triangle _{\mathbb{B}}$ is Fuchsian type Laplace operator investigated with totally characteristic degeneracy on the boundary $x_{1} = 0$. Firstly, we discuss the invariant sets and the vacuum isolating behavior of solutions with the help of a family of potential wells. Then, we derive a threshold result of existence and nonexistence of global weak solution: for the low initial energy $J(u_{0})<d$, the solution is global in time with $I(u_{0}) >0$ or $\displaystyle\Vert \nabla_{\mathbb{B}}u_{0}\Vert_{L_{2}^{\frac{n}{2}}(\mathbb{B})} = 0$ and blows up in finite time with $I(u_{0}) < 0$; for the critical initial energy $J(u_{0}) = d$, the solution is global in time with $I(u_{0}) \geq0$ and blows up in finite time with $I(u_{0}) < 0$. The decay estimate of the energy functional for the global solution and the estimates of the lifespan of local solution are also given.

Multimodal remote sensing data classification can enhance the model’s ability to distinguish land features through multimodal data fusion. In this context, how to help models understand the relationship between multimodal data and target tasks is the focus of researchers. Inspired by human feedback learning mechanisms, causal reasoning mechanisms, and knowledge induction mechanisms, this paper integrates causal learning, reinforcement learning, and meta learning into a unified remote sensing data classification framework and proposed the causal meta-reinforcement learning (CMRL). First, based on feedback learning mechanisms, we have overcome the limitations of traditional implicit optimization of fusion features and customized a reinforcement learning environment for multimodal remote sensing data classification tasks. Through feedback interactive learning between agents and the environment, we help them understand the complex relationships between multimodal data and labels, thereby achieving full mining of multimodal complementary information. Second, based on the causal inference mechanism we designed causal distribution prediction action, classification reward, and causal intervention reward, capturing pure causal factors in multimodal data and cutting off false statistical associations between non-causal factors and class labels. Finally, based on the knowledge induction mechanism, we designed a bi-layer optimization mechanism based on meta-learning. By constructing a meta training task and meta validation task simulation model in the generalization scenario of unseen data, we helped the model induce cross-task shared knowledge, thereby improving its generalization ability for unseen multimodal data. The experimental results on multiple sets of multimodal datasets show that the proposed method achieved state-of-the-art performance in multimodal remote sensing data classification tasks.

Moso bamboo is famous for fast growing and biomass accumulation, as well as high annual output for timber and bamboo shoots. These high outputs require high nutrient inputs to maintain and improve stand productivity. Soil nitrogen (N), phosphorus (P) and potassium (K) are important micronutrients for plant growth and productivity. Due to high variability of soils, analysing spatial patterns of soil N, P and K stocks is necessary for scientific nutrient management in Moso bamboo forests. In this study, soils were sampled from 138 locations across Yong’an City and ordinary kriging was applied for spatial interpolation of soil N, P and K stocks. Soil N stock showed a strong spatial dependence while soil N and P stocks presented a moderate spatial dependence, indicating soil N was mainly controlled by intrinsic factors while soil N and P stocks were controlled by both intrinsic and extrinsic factors. Different spatial patterns were observed for soil N, P and K stocks across the whole study area, indicating that fertilizations with different ratios of N:P:K should be applied for different sites to maintain and improve stand productivity. The total soil N, P and K stocks within 0-60 cm were 0.624, 0.020 and 0.583 Tg, respectively.

With the increasing concern of environment, the energy-efficiency scheduling of manufacturing industry is becoming urgent and popular. In turning processes, both spindle speed and processing time can affect the final energy consumption and thus the spindle speed and scheduling scheme need to be optimized simultaneously. Since the turning workshop can be regarded as the flexible flow shop, this paper formulates a mixed integer linear programming model for energy-efficient scheduling of flexible flow shop. Accordingly, a new decoding method is developed by considering of the optimization of spindle speed and scheduling scheme simultaneously, and an estimation of distribution algorithm adopting the new decoding method is proposed to solve large-size problems. The parameters of this algorithm are determined by statistical technique with a simplified practical case. In order to validate the proposed method, a case from practical factories is studied, in which the makespan can be shortened by 25.22%, and the consumed energy can be saved by 5.48%. These results demonstrate the effectiveness of the proposed mathematical model and algorithm.

Lignocellulosic biomass, an abundant and renewable resource, serves as a crucial raw material for the production of biofuels, biochemicals, and various value-added products. This paper aims to develop and optimize a mild alkaline treatment of sawdust assisted by ultrasound, along with enzymatic hydrolysis of the pretreated material. The sonochemical pretreatment with alkali emerged as the optimal approach to enhance the susceptibility of cellulose to subsequent enzymatic hydrolysis, thereby increasing the yield of reducing sugars. A comparative study was performed using various ultrasonic applicators (horn and bath) and conventional assisted alkaline pretreatment. The ultrasonic assisted pretreatment revealed a higher delignification as 68% (horn) and 57% (bath) comparing with conventional pretreatment. Processes were optimized using a statistical analysis based on a 23 factorial design. The ratio between sawdust and alkanine solution (RSL = 0.5–1.5 g/100 mL), US amplitude (A = 20–60%), and working temperature (t = 30–50 °C) were selected as process factors. The optimal operating conditions to maximize the reducing sugar yield (138.15 mg GE /gsubstrate) were found as following: solid/liquid ratio RSL,opt = 1.25 g/100 mL, US amplitude Aopt = 60%, and and pretreatment temperature topt = 50 °C. The overall outcomes clearly confirmed the intensification of delignification by ultrasound assisted alkaline pretreatment

At 12:28 UTC (8:28 PM, local time) on 15 January 2023, a shallow, moderate earthquake with a magnitude (Mw) of 4.7 and a depth of one (1) kilometer shook the northern part of Leyte Island in the central part of the Philippines. The ground shaking was felt at PHIVOLCS Earthquake Intensity Scale (PEIS) VI, (very strong) equivalent to Modified Mercalli Intensity (MMI) VI in areas along the strike of the Leyte segment of the Philippine Fault. Even though this earthquake is classified as moderate in size, significant geologic, structural, and socio-economic impacts were documented. Most of the earthquake impacts that include surface rupture, liquefaction, and mass movements are limited near the epicentral area. The earthquake produced an 8-km-long surface rupture, the first documented rupture generated by a magnitude &lt;6 along the Philippine Fault, and is unusual in other surface rupturing earthquakes worldwide. It injured 18 persons and damaged 434 residential buildings and 26 public infrastructures which amounts to about 500 thousand US dollars. Structural damages were caused by surface rupture and/or poor engineering construction practices. Analysis of the seismic waveform and recorded peak ground acceleration (PGA) suggests that the subsurface geology influenced the ground motion amplification in an area near the epicenter. Based on the hypocenter, focal mechanism solution, aftershock distribution, and actual field observation, the causative fault for this event is the northern end of the Philippine Fault – Leyte segment. Moderate in size, this earthquake emphasizes the need and importance of documenting moderate-sized earthquakes as a tool and guide for medium and long-term earthquake risk assessment and resiliency.

Background: The bacterium Capnocytophaga spp. is a part of the oral microbiome of dogs, which has zoonotic potential. This study aimed to assess factors that influence the prevalence of Capnocytophaga cynodegmi and Capnocytophaga canimorsus in Wrocaw’s dog population. Methods: Molecular detection (PCR) involved 105 swabs, examining parameters such as oral cavity condition, underlying health issues, recent antibiotics, age, medications, material collection, and dog chews. Results: The study highlighted significant associations between the presence of Capnocytophaga cynodegmi and oral cavity condition, material collection method, and use of dog’s chews. Conclusions: Correlations obtained in this study between the oral health of Wroclaw's dog population and the presence of Capnocytophaga cynodegmi suggest its significance in the oral microbiome of dogs. Limitations, including the small sample size, highlight the need for more research to comprehensively understand additional factors that affect the prevalence of Capnocytophaga spp. in dogs

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

A simple design of an ultrathin six-band polarization-insensitive terahertz perfect metamaterial absorber (PMMA) composed of a metal cross-cave-patch resonator (CCPR) placed over a ground plane was proposed and investigated numerically. The numerical simulation results demonstrate that the average absorption peaks are up to 95% at six resonance frequencies with high quality-factors (>65). In addition, the absorption properties can be kept stability for both normal incident transverse magnetic (TM) and transverse electric (TE) waves. The physical mechanism behind the observed high level absorption is illustrated by the electric and power loss density distributions. The different absorption mainly originates from the higher order multipolar and multipolar plasmon resonance of the structure, which are sharp different to the most previous studies of the PMMAs. Furthermore, the resonance absorption of the PMMA can be tunable by varying the geometric parameters of the unit cell.

The assortment of low-cost 3D printers for “in-practice” use, e.g., for clear aligner therapies, is ever increasing. To address concerns about the accuracy of orthodontic models produced on such printers when cost efficient modes of 3D printing are employed, this study examined the effect of print model body type and print angulation on accuracy. Six printing-configuration groups were included: 2 model types (solid or hollow shell) combined with 3 print angles (0°, 70°, or 90°) with 10 models/group; all models were printed with 100-µm layer thickness using a digital light processing-based 3-dimensional printer. Eleven selected structures and distances were measured on the printed models with a digital microscope and compared to the same measures on a digitized master model. The clinically-acceptability range was set at ±0.25 mm difference from the master model for single tooth measurements (intra-tooth) and ±0.5 mm for cross-arch measurements (inter-tooth). For individual measurements across all models, 98% fell within clinical acceptability. For mean measurements within each model group, only canine height for the shell-0° model had a mean difference (0.26 mm ± 0.03) outside the clinically acceptable range for intra-tooth measurements. Standard deviations for all intra-tooth measurements were within 0.07 mm. While none of the mean inter-tooth measurements exceeded the acceptability range, the standard deviations were larger (0.04 to 0.30 mm). Accuracy of orthodontic models for clear aligner therapies was not impacted beyond the clinically acceptable range when altering model body type and print angulation to improve efficiency of 3D printing. These findings suggest greater flexibility of the practitioner to alter print settings to address time and cost efficiency in various clinical scenarios and still maintain clinically acceptable model accuracy.

Background: Alfalfa, the most economically important forage legume worldwide, features modest genetic progress due to long selection cycles and large extent of non-additive genetic variance associated with its autotetraploid genome. Methods: To improve the efficiency of genomic selection in alfalfa, we explored the effects of genome parametrization (as autotetraploid and diploid dosage, plus allele ratios) and SNP marker subsetting (all available SNPs; only genic regions; only non-genic regions) on genomic regressions, together with various levels of filtering on reading depth and missing rates. We used Genotyping by Sequencing-generated data and focused on traits of different genetic complexity, i.e., dry biomass yield in moisture-favorable (FE) and drought stress (SE) environments, leaf size, and onset of flowering, assessed on 143 genotyped plants from a genetically-broad European reference population and their phenotyped half-sib progenies. Results: On average, allele ratio improved the predictive ability compared with other genome parametrizations (+7.9% vs. tetraploid dosage, +12.6% vs. diploid dosage), SNP subsetting offered an advantage compared with any tested subsettings (+3.7% vs. genic regions, +7.6% vs. non-genic regions). However, when focusing on specific traits, different combinations of genome parametrization and subsetting reached better performances. We also released Legpipe2, a SNP calling pipeline tailored for reduced representation (GBS, RAD) medium-sized genotyping experiments.

Climate change is challenging the agricultural sector worldwide. The pressure exerted by the altered thermal conditions drives the zonal shift for various cultivations. This study presents the multiyear analysis of the Growing Degree Days (GDD) index over the Northern Mediterranean Basin (NMB), focused on the high-value vine cultivation derived from the E-OBS dataset. To handle this extensive environmental dataset, R-language scripts and packages were applied, along with the capabilities of the GIS software. The investigated time period spans from 1969 to 2018, and the performed analysis indicates a broad shift/expansion in areas of GDD exceeding 2000 heat units. The extracted results specify the viticultural areas where the GDD index surpasses the suitable values for vine cultivation, owing to the increase of the thermal stress risk. In addition to mapping areas with GDD ≥ 2000, spatial calculations of the surface of areas meeting this criterion per country in the study area were made. In the northern parts of the NMB, the rise of the GDD index values indicates the establishment of vine plantations in the future.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x104 – 2x107 CFU per ml and has a sensitivity of S = 1.655x105 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10-9 grams (g) which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

Regeneration of lost tail is of great importance to lizards. Anolis carolinensis, a green lizard, is capable of regenerating its tail efficiently after autotomy. Hence, it is considered as a model organism in regeneration study. A. carolinensis shed its tail in order to distract the predator’s attention and thus makes a way to escape. Restoring of the amputated tail takes several days and the mechanism is currently clearly understood. Although save its life, tail regeneration is associated with the impairment of several vital functions in Anoles. In addition, various differences have been observed between original and regenerated tail in terms of mechanism and structure. To date, very little work has been conducted on tail autotomy and regeneration at molecular and genetic level. The genes responsible for regeneration in anoles are identified recently. These genes are evolutionarily conserved through all tetrapod vertebrates. They are, however, in a state of ‘switched-off’ in other vertebrates including humans. Consequently, a throughout study of these so called ‘switched-off’ genes may provide a way of restoring lost organs in human, and thus could revolutionize the modern medical science.

The strong competition in the automotive industry has required manufacturers to implement lean production, both with methods and techniques specific to Industry 4.0. At the same time, universities must provide graduates with specific skills for applying these new production methods and techniques. In this context, a Lean Learning Factory was developed in the Pitesti University Center, which allows students to learn, experiment, and research, in an environment similar to that of enterprises, the new Lean Manufacturing methods and techniques, and Industry 4.0. The research presented in this study had as its objective identifying the minimum number of repetitions necessary to train operators who serve two differently organized workstations, one classic, the other including digital techniques, but on which the same assembly operation is performed. Several indicators were considered in the analysis, such as the number of errors, the number of stops, the effective duration of the work cycle, and the percentage ratio between the standard duration of cyclical activities and the effective duration of the work cycle. The evolution of these indicators was mathematically modelled by regression functions, using the least squares method. The obtained results also highlight the usefulness of applying the DOJO method as a Lean manufacturing-specific learning technique and the efficiency of implementing digital techniques in work organization.

Classifying network flow subsequences in an Industrial IoT gateway is an effective method for identifying Industrial IoT faults. This paper proposes a subsequence classification algorithm SSGBUL-IKNN based on unsupervised learning encoding to address the problem of low classification accuracy. Firstly, we built a network module based on unsupervised learning to encode the flow sequence of the Industrial IoT gateway. In the encoding module, a subsequence calibration algorithm controls the increasing error during the coding process. Then, the specific fault type is obtained through an improved KNN classification algorithm based on the indication distance source from the integrated coding sequences converted by multi-dimensional network flow sequences. The test result on three Industrial IoT datasets of a sewage treatment plant shows that the accuracy of SSGBUL-IKNN in this paper exceeds 92%, significantly higher than the algorithm DTW and TSF. It reaches the classification requirements of Industrial IoT fault diagnosis.

In this paper, we study the global existence and exponential decay for a dynamic contact problem between a Timoshenko beam with second sound and two rigid obstacles, of which the heat flux is given by Cattaneo's law instead of the usual Fourier's law. The main difficulties arise from the irregular boundary terms, from the low regularity of the weak solution and from the weaker dissipative effects of heat conduction induced by Cattaneo's law. By considering related penalized problems, proving some a priori estimates and passing to the limit, we prove the global existence of the solutions. By considering the approximate framework, constructing some new functionals and applying the perturbed energy method, we obtain the exponential decay result for the approximate solution, and then prove the exponential decay rate to the original problem by utilizing the weak lower semicontinuity arguments.

Reducing the hardness of hard water is of great concern nowadays due to some adverse effects on water pipes, boilers and soap consumption. Using the method of biomineralization to precipitate calcium and magnesium ions to become carbonate minerals was one of the most important innovations for reducing the hardness of hard water. The present study sought to explore the physical and chemical conditions of carbonates bio-precipitation and the potential use of Bacillus licheniformis SRB2 strain (GenBank: KM884945.1) isolated from sludge sample of Moshui River (Shandong University of Science and Technology, Qingdao, China) in reducing the hardness of hard waters by the induction of carbonate minerals. In this study, B. licheniformis SRB2 strain was identified based on the morphological, biochemical and 16S rDNA gene sequence homology analysis. The carbonate minerals induced by B. licheniformis bacteria in the liquid culture medium with 3% NaCl and Mg/Ca molar ratio of 0, 6, 8, 10 and 12 were investigated. The culture medium was inoculated with the bacterial liquid seed was set as the experimental group and the other culture medium was inoculated with the same volume of distilled water was set as the control group. The mineral phases, micromorphologies, and crystal structures were analyzed using X-ray powder diffraction, scanning electron microscope, energy dispersive X-ray detector, high resolution transmission electron microscopy and selected area electron diffraction. The bacterial concentrations and pH values of the solution were measured by a spectrophotometer and a pH meter, respectively. The urease secreted by B. licheniformis SRB2 was found to greatly increase the pH values of the liquid medium, which favored the formation of calcium carbonate.As a result, Mg²⁺ and Ca²⁺ ion concentrations decreased greatly due to the biomineralization of calcium carbonate and nesquehonite minerals in the presence of B. licheniformis SRB2 bacterium. There were only few calcium carbonates and no nesquehonite minerals in the control groups. It was also found that the minerals of nesquehonite induced by B. licheniformis SRB2 had a phenomenon of preferred orientation. What was more, even though Mg²⁺ ions inhibited the precipitation of Ca²⁺ ions, but under the action of B. licheniformis SRB2 bacteria, the inhibition effect was significantly declined. The bio-precipitation of calcium carbonate and nesquehonite minerals may represent a new method of pretreatment for the hardness reduction of hard water. The accomplished study is of certain interest for interpretation of the carbonates biomineralization in natural environment, and maybe also has a certain application value in the former processing of hard water

In this paper, a novel permanent magnet-assisted synchronous reluctance machine (PMASynRM) with rare-earth PMs and ferrite magnets is proposed. The performance of PMASynRM is discussed with respected to the different magnet ratio of rare-earth PMs and ferrite magnets. Some characteristics including the flux density, output torque, cogging torque, output power, power factor, torque ripple, loss, efficiency, and demagnetization are calculated by 2-D finite element analysis (FEA). The analysis results show that the excellent performance can be obtained by using hybrid magnet of rare-earth PMs and ferrite magnets with the suitable magnet ratio, and provide some desirable cost-performance trade-off.