The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

An laboratory procedure has been developed to obtain lanthanum oxide from spent fluid catalytic cracking catalyst, commonly used in the cracking the heavy crude oil process. Two different spent fluid catalytic cracking catalysts, which are mainly formed by silica and alumina, and a certain amount of rare earths were leached under several conditions to recover the rare earth from the solids waste. Subsequently, liquid phases were subjected to a liquid-liquid extraction process, and lanthanum was quantitatively stripped using oxalic acid to obtain the corresponding lanthanum oxalates. After the corresponding thermal treatment, these solids were transformed into lanthanum oxide. Both, lanthanum oxalates and oxides solids have been characterized by wide techniques in order to investigate the purity of the phases.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

In the FCC conversion of heavy petroleum fractions as atmospheric residues, the main challenge for refiners to achieve the quantity and quality of various commercial products depends essentially on the catalyst used in the process. A deep characterization of the catalyst at different steps of the process (fresh, regenerated, and spent catalyst) was investigated to study the catalyst's behavior including the physicochemical evolution, the deactivation factor, and kinetic-thermodynamic parameters. All samples have been characterized by various spectroscopy methods such as N2 adsorption-desorption, UV-visible spectroscopy, Raman spectroscopy, LECO carbon analysis, Scanning electron microscopy (SEM), X-ray diffraction (XRD), X‐ray fluorescence (XRF), nuclear magnetic resonance spectroscopy (NMR13C) analysis, and Thermogravimetric analysis. The results of N2 adsorption-desorption, UV-vis, Raman, LECO carbon, and SEM images showed that the main causes of catalyst deactivation and coking were the deposition of carbon species that covered the active sites and clogged the pores, and the attrition factor due to thermal conditions and poisonous metals. The XRD and XRF results showed the catalyst’s physicochemical evolution during the process and the different interlinks between catalyst and feedstock (Nickel, Vanadium, Sulfur, and Iron) elements which should be responsible for the coking and catalyst attrition factor. It has been found that, in addition to the temperature, the residence time of the catalyst in the process also has an influence on catalyst structure transformation. NMR13C analysis revealed that polyaromatic hydrocarbon is the main component in the deposited coke of the spent catalyst. Thermogravimetric analysis showed that the order of catalyst mass loss was fresh > regenerated > spent catalyst due to the progressive losses of the hydroxyl bonds (OH) and the structure change along the catalyst thermal treatment. Moreover, the kinetic and thermodynamic parameters showed that all zones are non-spontaneous endothermic reactions.

Associating the most influential parameters with the product distribution is of uttermost importance in complex catalytic processes such as fluid catalytic cracking (FCC). These correlations can lead to the information-driven catalyst screening, kinetic modeling and reactor design. In this work, a dataset of 104 uncorrelated experiments, with 64 variables, has been obtained in an FCC simulator using 6 types of feedstock (vacuum gasoil, polyethylene pyrolysis waxes, scrap tire pyrolysis oil, dissolved polyethylene and blends of the previous), 36 possible sets of conditions (varying contact time, temperature and catalyst/oil ratio) and 3 industrial catalysts. Principal component analysis (PCA) has been applied over the dataset, showing that the main components are associated with feed composition (27.41% variance); operational conditions (19.09%) and catalyst properties (12.72%). The variables of each component have been correlated with the indexes and yields of the products: conversion, octane number, aromatics, olefins (propylene) or coke, among others.

The study experimentally investigated a novel approach for producing hydrogen from methane cracking in dielectric barrier discharge catalytic plasma reactor using a nanocatalyst. Plasma-catalytic methane (CH4) cracking was undertaken in a dielectric barrier discharge (DBD) catalytic plasma reactor using Ni/MgAl2O4. The Ni/MgAl2O4 was synthesised through co-precipitation followed customised hydrothermal method. The physicochemical properties of the catalyst were examined using X-ray diffraction (XRD), scanning electron microscopy - energy dispersive X-ray spectrometry (SEM-EDX) and thermogravimetric analysis (TGA). The Ni/MgAl2O4 shows a porous structure spinel MgAl2O4 and thermal stability. In the catalytic-plasma methane cracking, the Ni/MgAl2O4 shows 80% of the maximum conversion of CH4 with H2 selectivity 75%. Furthermore, the stability of the catalyst was encouraging 16 hours with CH4 conversion above 75%, and the selectivity of H2 was above 70%. This is attributed to the synergistic effect of the catalyst and plasma. The plasma-catalytic CH4 cracking is a promising technology for the simultaneous H2 and carbon nanotubes (CNTs) production for energy storage applications.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

Thermal and catalytic pyrolysis of virgin low-density polyethylene (LDPE), high-density polyethylene (HDPE), polypropylene (PP) and mixtures of LDPE/PP were carried out in a 200 ml laboratory scale batch reactor at 460 °C in a nitrogen atmosphere. Thermogravimetric analysis (TGA) was carried out to study the thermal and catalytic degradation of the polymers at a heating rate of 10 °C/min. The amount of PP was varied in the LDPE/PP mixture to explore its effect on the reaction. In thermal degradation (TGA) of LDPE/PP blends, a lower decomposition temperature was observed for LDPE/PP mixtures compared to pure LDPE, indicating interaction between the two polymer types. In the presence of a catalyst (CAT-2), the degradation temperatures for the pure polymers were reduced. The TGA results were validated in a batch reactor using PP and LDPE respectively. Thermal cracking results showed that the oil product contains a significant amount of gasoline (C7 − C12) and diesel (C13 − C20) hydrocarbon fractions. The catalyst enhanced cracking at lower temperatures and narrowed the hydrocarbon distribution in the oil towards the gasoline range fraction (C7 – C12). The result suggests that the oil produced from catalytic pyrolysis of waste plastics has a potential as an alternative fuel.

Aerobic vaginitis (AV) is a distinct clinical entity characterized by inflammation and abnormal vaginal microflora. Often mistaken for bacterial vaginosis, AV remains relatively unknown and underdiagnosed. AV's understanding is evolving, with some experts suggesting it may primarily be an immunological disorder, the prevalence of which ranges from 7-13% in non-pregnant women and 4.1-8.3% during pregnancy. Pregnancy can affect susceptibility to vaginal infections, leading to adverse outcomes for the woman and the newborn. This review summarizes the correlation between AV and adverse pregnancy outcomes, particularly preterm birth, the leading cause of morbidity and mortality among neonates. Improved understanding of AV's impact on pregnancy outcomes can lead to early recognition, proper management, and effective interventions. While some studies support an association between AV and preterm labor, the existing knowledge of this relationship remains limited. The evidence suggests that AV may contribute to adverse pregnancy outcomes, mainly preterm birth, but further research is needed to establish a definitive link. Further studies are needed to investigate the underlying mechanisms and clarify AV's role in premature labor. A comprehensive understanding of AV's impact on pregnancy outcomes is crucial for early recognition, appropriate management, and effective interventions.

Plastics have become an indispensable part of modern life today. The global production of plastics has gone up to 299million tones in 2013, which is believed to be increasing in the near future. The utilization of plastics and its final disposal pose a tremendous negative significance impacts on the environment. The aim of this study was to investigate the thermal and catalytic pyrolysis for production of fuel oil from the polyethene plastic wastes. Catalysts used in the experiment were acid activated clay mineral and aluminum chlorides on activated carbon. The clay mineral was activated by refluxing it with 6M Sulphuric acid for 3hours. The experiment was conducted in three different phases: the first phase of the experiment was done without a catalyst where 88mL oil was obtained at a maximum temperature of 39 and heating rates of 12.5, reaction time of 4hours. The second phase involves the use of acid activated clay mineral where 100mL of oil was obtained and heating rates of 12.5 and reaction time of 3hours 30minutes. The third phase was done using aluminium chlorides on activated carbon and 105ml oil was obtained at a maximum temperature of 400 and heating rates of 15.5 reaction time of 3hours 10minutes. From the results, catalytic pyrolysis is more efficient than purely thermal pyrolysis and homogenous catalysis (aluminum chlorides) shows a better result than solid acid catalyst (activated clay minerals) hence saving the energy needed for pyrolysis and making the process more economically feasible.

Metal-organic frameworks (MOFs) have been subject of extensive scientific investigation in the last three decades and, currently, are one of the type of compounds most studied to be potentially applied in a wide range of distinct catalytic processes. Pristine MOF compounds provide several intriguing benefits for catalytic applications, including high interior surface areas and densities of active sites, allowing high catalytic reaction rates per volume, post-synthesis modified with com-plementary catalytic groups, enabling multiple functional groups to catalyze the reaction. Most of large-scale catalytic applications, including those in fuel processing, gas emission reduction and chemical synthesis, nevertheless the pristine MOFs often reveal limited stabilities and opportuni-ties for regeneration at high temperatures. As a result, the real applications of MOFs in these tech-nologies are likely to be constrained, and their controlled thermal modification aiming the prepa-ration of MOF-derivative compounds has been applied to induce crystalline structural changes and increase their structural stability, enhancing its potential applicability in more severe catalytic processes. Recent advances concerning the use of this strategy to boost the catalytic potential of the MOF-derivative compounds are outlined in this short-review article.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

This article presents a description of a new method for solving the factorization problem, based on the gradient descent algorithm. This approach demonstrates significant improvements in efficiency compared to traditional methods proposed in previous research. This article describes a new method for solving the factorization problem, based on the gradient descent algorithm, and demonstrates the transition from algebraic methods to approaches based on functional analysis. The proposed approach not only improves the efficiency of solving the problem but also allows the application of computational algorithms of functional analysis, opening new possibilities for research and optimization.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

A four-step synthesis of bifunctional, noncovalent organocatalysts based on the chiral (1R,2R)-cyclohexane-1,2-diamine scaffold containing a 1,2-benzenediamine H-bond donor was developed. Nucleophilic aromatic substitution of the 2-fluoronitrobenzene derivative with the commercial (1R,2R)-cyclohexane-1,2-diamine was followed by selective alkylation of the primary amino group, reduction of the aromatic nitro group and final derivatization of the primary aromatic amino group, i.e. acylation, sulfonation, reductive alkylation and arylation, leading to the four subtypes of organocatalysts. All new compounds were fully characterized. The prepared organocatalysts (32 examples) were tested in the Michael addition of acetylacetone to trans-β-nitrostyrene, yielding the addition product with incomplete conversions (up to 93%) and enantioselectivities of up to 41% ee.

In this research, catalytic steam reforming acetic acid derived from the aqueous portion of bio-oil for hydrogen production was investigated by using different Ni/ATC (Attapulgite Clay) catalysts prepared by precipitation, impregnation and mechanical blending methods. The fresh and reduced catalysts were characterized by XRD, N₂ adsorption-desorption, TEM and H₂-TPR. The comprehensive results demonstrated that the interaction between active metallic Ni and ATC carrier was significantly improved in Ni/ATC catalyst prepared by precipitation method, and in which the mean Ni particle size was the smallest (~13 nm) resulted in the highest metal dispersion (7.5%). The catalytic performance of the three catalysts was evaluated through the process of steam reforming of acetic acid in a fixed-bed reactor under atmospheric pressure at two different temperatures, such as 550 ℃ and 650 ℃. Results showed that the Ni/ATC (PM-N/ATC) prepared by precipitation method, achieved the highest H₂ yield of ~82% and little lower acetic acid conversion efficiency of ~85% than that (~95%) of Ni/ATC (IM-NATC) prepared by impregnation method. In addition, the deactivation catalysts after reaction for 4 h were analyzed by XRD, TGA-DTG and TEM, which demonstrated that the catalyst deactivation was not caused by the amount of carbon deposition, but owed to the significant agglomeration and sintering of Ni particles in the carrier.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

In this work, the influence of catalyst reuse and reaction time on the yield and quality of organic liquid products (OLP) obtained in a cracking pilot plant at 450 °C and 1.0 atm has been systematically investigated. The distillation of OLP produced 04 (four) distilled fractions. The quality of the biofuels was certified by physical-chemical analysis, as well as FT-IR and GC-MS analysis. The experimental results showed the feasibility of applying the spent sodium carbonate twice in catalytic cracking of vegetable oils. The physical-chemical properties (density, viscosity, acid value, saponification value, and flash point) of OLP decrease as the reaction time increases. The distillation of OLP yields 62.35% (wt.), producing green-like gasoline, kerosene, and diesel fractions rich in hydrocarbons. Therefore, biofuels-like fractions produced by distillation of OLP have a great potential for replacing partially petroleum derived fuels.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

In terms of obtaining fuels as well as chemicals with or without catalysts at different conditions, the plum seed stands out as an alternative biomass source. Under varying heating rates (10, 50, and 100ºC min-1) and pyrolysis temperatures (400, 450, 500, 550 and 600 °C), the plum seed was pyrolysed at constant sweep gas flow at a constant rate (100 cm3min-1) in a tubular fixed bed reactor. According to the results, an oil yield reaching to a maximum of %45 was procured at the heating rate of 100 ºCmin-1 and the pyrolysis temperature of 550ºC in non-catalytic procedure. The catalytic pyrolysis was carried out in optimum conditions with two selected commercial catalysts, namely ZSM-5 and PURMOL-CTX and clinoptilolite (natural zeolite, NZ) with catalyst ratio of 10 % of raw material. Along with the catalyst addition, the quantity and the quality of bio-oil increased including the calorific value, removal of oxygenated groups, and hydrocarbon distribution. An increase related to the desirable products like phenols, alkene, and alkane and a decrease in undesirable products like acids were observed in the presence of catalysts. When all the results are considered and evaluated, using zeolite materials in the pyrolysis as catalysts is a recommendable option to achieve enhanced chemicals and fuels.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

Fruit cracking or splitting, a severe physiological disease that highly affects appearance and quality, compromise the commodity value of fruit and also causes huge economical losses to the producers of several fleshy fruit crops. The growth-promoting phytohormone gibberellic acid (GA) and growth-inhibiting phytohormone abscisic acid (ABA) antagonistically regulate numerous developmental processes throughout the plant life cycle. Homeostasis of endogenous GA and ABA play a significant role in the normal growth of fruits, and its imbalance may lead to the occurrence of cracking or splitting during the process of fruit growth, development, ripening and postharvest storage. The pathways of GA and ABA metabolism and signaling have been studied widely, and the major components were well characterized, which including the genes encoding major biosynthesis and catabolism enzymes and the key signaling components. Nevertheless, our knowledge of the mechanisms of GA and ABA governing fruit cracking is not comprehensive enough. In this review, we not only focus on the scenarios of effects of endogenous GA and ABA contents in the fruit and exogenous plant growth regulators GA and ABA treatments, but also endeavor to provide some genetic cues on the function of GA and ABA responsible for fruit cracking modulation. Information from this review aims to strengthen the understanding of potential molecular bases underlying GA and ABA in fruit cracking control and provide guidance in breeding of fruit cultivars with cracking-resistant ideotypes, and also make great theoretical significance in guiding the establishment of integrated prevention and control measures to fruit cracking or splitting.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

This work aims to investigate systematically the tecno-economic feasibility of ther-mos-catalytic cracking process for two solid waste materials, a lipid-base material (re-sidual fat/scum from retention box of the University Restaurant of UFPA) and a lig-nin-cellulosic material Açaí seed (Euterpe oleracea. Mart). The thermo-catalytic process-es were carried out in pilot scale (THERMTEK/LEQ/UFPA/IME/RJ), and their economic feasibility analyzed. The yields of biofuels produced by fractional distillation were al-so studied. The physicochemical characteristics of the raw materials, the organic liquid product (bio-oil) and the chemical composition of kerosene, light-diesel and heavy-diesel from the lipid-base material, as well as those of kerosene and light-diesel from the Açaí seed were also determined. The economic indicators for the evaluation of the most viable cracking (pyrolysis) and distillation process of bio-oils were: a) the sim-ple payback criterion, b) discounted payback, c) net present value (NPV), d) internal rate of return (IRR), and e) index of profitability (IP). The analysis of the indicators showed the economic viability of crude palm oil (Elaeis guineensis, Jacq) and unfeasibil-ity for the palm oil neutralization. The minimum fuel selling price (MFSP) obtained is this work for the biofuels was of 1.34 US$/L) and the breakeven point obtained was of 1.28 US$/L. The sensibility analysis demonstrated that the pyrolysis and distillation yields are the most important variables to affect the minimum fuel selling price (MFSP).

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

3,4-Dihydroquinolin-2(1H)-ones represent a class of valuable bioactive compounds with six-membered nitrogen-containing heterocyclic structures. The development of simple, mild and efficient synthetic methods has been widely concerned by synthetic chemists. In this review, we have summarized a series of different synthetic strategies for the synthesis of dihydroquinoline-2(1H)-ones via catalytic annulation of α,β-unsaturated N-arylamides in the past decade, including covering electrophilic cyclization, radical initiated cyclization and photochemical cyclization reactions. Besides, the substrate scope and mechanistic details are also discussed. This paper will provide a useful reference for the development of diverse synthesis methodologies of 3,4-dihydroquinolin-2(1H)-ones.

K417G Ni-based superalloy is widely used in aeroengine turbine blade for its excellent properties. However, the aeroengine rotor blade zigzag crown appears early failure frequently, which is because of the wear problems occurring in the working process. Laser forming repairing (LFR) is a promising technique to repair these damaged blades. Unfortunately, the laser formed Ni-based superalloys with high content of (Al + Ti) have a high cracking sensitivity. In this paper, the crack characterization of the LFRed K417G, the microstructure, microhardness and tribological properties of the coating before and after laser remelting are presented. The results show that the microstructure of as-deposited K417G consists of γ phase, γ′ precipitated phase, γ + γ′ eutectic and carbide. Cracking mechanisms including solidification cracking, liquation cracking and ductility dip cracking are proposed based on the composition of K417G and processing characteristics to explain the cracking behavior of the K417G superalloy during LFR. After laser remelting, the microstructure of the coating has been refined, and the microhardness and tribological properties has been improved. Laser remelting can decrease the size of the cracks in the LFRed K417G but not the number. Therefore, laser remelting can be applied as an effective method for strengthening coating and as an auxiliary method for controlling cracking.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

“Clickase” single-chain nanoparticles (Ck-SCNPs) are folded, enzyme-mimetic unimolecular polymeric nano-objects containing copper (Cu) ions able to catalyze the azide-alkyne Huisgen cycloaddition reaction in water and/or selected organic solvents, often in the presence of a reductant. Herein, we investigate the effect of morphology on catalytic activity of Ck-SCNPs synthesized by means of two different routes. An amphiphilic random copolymer composed of oligo(ethylene glycol) methyl ether methyl methacrylate (OEGMA) and 2-acetoacetoxy ethyl methacrylate (AEMA) units was used as precursor of these Ck-SCNPs. Folding was promoted through metal complexation between Cu(II) ions and beta-ketoester-containing AEMA moieties. The first route resulted in Ck-SCNPs1 containing Cu ions homogeneously distributed within each nanoparticle, whereas the second one promoted intra-chain clustering of Cu ions inside Ck-SCNPs2. A model fluorogenic “click” reaction between 9-(azidomethyl)anthracene and phenylacetylene, which was catalyzed either by Ck-SCNPs1 or Ck-SCNPs2, was used to unravel the effect of morphology on catalytic activity. This work paves the way to improve the catalytic activity of metallo-folded SCNPs through control of the intra-chain distribution of catalytic sites.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

Two austenitic stainless steel (ASS) plates, 304L and 316L, were cold-rolled (304R and 316R) with a 10 % reduction in thickness then subjected to laser welding. Cold-rolling caused a slight surface hardening and introduced residual tensile stress into the ASS plates. The susceptibility to stress corrosion cracking (SCC) of the welds (304RW and 316RW) was determined using the U-bend test pieces in a salt spray. To highlight the stress concentration at the weld’s fusion boundary (FB), the top weld reinforcement was not ground off before bending. Moreover, micro-shot peening (MSP) was performed to mitigate the SCC of the welds by imposing high residual compressive stress and forming a fine-grained structure. Cold-rolling increased the susceptibility of the 304R specimen to pitting corrosion (PTC) and intergranular (IG) microcracking. Moreover, PTC and SCC were found more often at the FBs of the 304RW. The corrosion pits of the peened 304RW (304RWSP) were finer but greater in amount than the un-peened one. The results also indicated that the 316L ASS welds with MSP was resistant to the incidence of PTC and SCC in a salt spray. The better reliability and longer service life of dry storage canister could be achieved by using 316L ASS for construction and application of MSP on it.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

This study represents a significant stride in advancing furan chemistry, presenting the synthesis of high-molecular-weight polyfurfuryl alcohol (PFA) resin (Mw = 118,959 g/mol) from furfuryl alcohol (FA) using a co-catalytic system as against the conventional single-catalytic methods. The resulting PFA resin is fully characterised, and we conclude that it exhibits good shelf life and potential in diverse applications, serving as a standalone moulded material or contributing to composites, coatings, adhesives, and nanostructured carbons.

Fly ash cement has rarely been used in Japan, mainly because its strength development is slower than ordinary Portland cement. In this research, the effect of the new fly ash cement with both high alite (C3S) cement and fly ash modified by electrostatic belt separation method on cracking resistance of precast concrete prepared by steam curing was studied. The mechanical and shrinkage properties of the proposed fly ash concrete were compared with those of concrete made using OPC cement without fly ash. In order to study the cracking tendency of precast concrete with the proposed fly ash cement, thermal stress analysis was conducted taking into consideration of the experimental data of concrete properties with the different concrete mix proportions. A standard precast concrete box culvert model was used in this 3D FEM analysis and the distribution of temperature and relative humidity in cross section and induced restraint stress during and after steam curing were discussed. Steam-cured concrete with fly ash and high alite cement developed higher compressive strength on the first day of age than concrete with OPC. The proposed fly ash concrete developed high cracking resistance in the early days. On the other hand, the results showed that the drying shrinkage at later ages was the main cause of cracking.

This article aimed to evaluate, using statistical tools, the generation and composition of urban solid waste (MSW) in the city of Belém, Pará, from nine urban collection sectors in the municipality, and the average nominal income of the population. Approximately 900kg of urban solid waste were col-lected from the municipality in the period from 2021 to 2022. Statistical tests were carried out on hypotheses with 5% significance in comparative evaluations, and their respective average nominal incomes. The results indicated that the organic fraction corresponds to 55.57% of the waste generated in the municipality, 14.26% is inert waste (potentially contaminating) and 0.67% is miscellaneous waste. It was observed that the waste generated by families with high purchasing power tends to contain higher percentages of recyclables, while in families with lower purchasing power the highest percentages tend to be organic. Knowledge of the generation of MSW is fundamental for the choice and dimensioning of operations and processes involved in the management chain at the municipal level. The decentralization of services offered based on solid waste management would enable greater success in serving the population.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Deep eutectic solvents are a mixture of two or more components, that at a particular composition become liquids at room temperature. When the compounds that constitute the DES are primary metabolites, namely, amino acids, organic acids, sugars, or choline derivatives, the DES are so called natural deep eutectic solvents (NADES). NADES fully represent green chemistry principles. These solvents are highly welcome, as they are obtained from renewable resources, and gratifyingly biodegradable and biocompatible. They are an alternative to room temperature ionic liquids (RTILs). From the pharmaceutical industry point of view, they are highly desirable, but unfortunately have been rarely used despite their enormous potential. In this review, we will look at their impact on the asymmetric catalytic synthesis of key target molecules, via metal-based catalysis, biocatalysis and organocatalysis. In many cases the NADES that have been used are chiral and can even promote enantioselective reactions, this crucial and very exciting aspect will also be discussed and analysed.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

Nickel molybdate, NiMoO₄, nanoparticles were synthesized via calcination of an oxalate complex in static air at 500 °C. The oxalate complex was analyzed by thermal gravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FTIR). The as-synthesized nickel molybdate was characterized by Brunauer–Emmett–Teller technique (BET), X-ray diffraction (XRD), and transmission electron microscopy (TEM) and its catalytic efficiency was tested in the reduction reaction of the three-nitrophenol isomers. The nickel molybdate displays a very high activity in the catalytic reduction of the nitro functional group to an amino. The reduction progress was controlled using UV-Vis absorption.

Exploration practices have proven that over mature shale gas exhibits a feature of carbon isotope reversal. The geochemical statistics indicate that the wetness (C2-C5/C1-C5) of shale gas with carbon isotope reversal is less than 1.8%. In addition, the magnitude of carbon isotope reversal (δ13C1- δ13C2) for the over mature shale gas presents a parabolic variation with decreasing wetness. δ13C1-δ13C2 increases with decreasing wetness within a wetness range of 0.9% ~1.8% and then decreases with decreasing wetness at wetness < 0.9%. The CH4 cracking experiment demonstrates that CH4 polymerization occurring in the early stage of CH4 cracking is an important factor involved in isotope reversal of over mature shale gas. Moreover, δ13C1- δ13C2 decreases with an increase in experimental temperature prior to CH4 substantial cracking. The values of δ13C1 and δ13C2 tend to equalize during CH4 substantial cracking. The δ13C1-δ13C2 of mud gas present at different depths during shale gas drilling in Sichuan Basin increases initially, then decreases with further increase in the depth and finally tends to zero, with only a trace hydrocarbon gas being detectable. Statistical data suggests that the shale gas production in Sichuan Basin decreases with the decreasing δ13C1-δ13C2 value and wetness. Thus, δ13C1-δ13C2 and wetness could potentially serve as useful criteria to screen CH4 cracking degree and to determine the largest depth of natural gas exploration. Great care should be taken during shale gas exploration in deeper layers, with wetness and δ13C1-δ13C2 less than 0.2% and 1%, respectively, since very low wetness (<0.2%) and δ13C1-δ13C2 (<1%) might be indicative of CH4 substantial cracking in a geological setting.

Polyphenols are well-known health promoting agents, but they have some limitations due to their spontaneous oxidation. This evidence has limited their use as drugs in the last years. In this field, several chemical modifications have been proposed to overcome these restrictions; among these, the esterification seems to be the preferred. Ester derivatives could be able to reduce the bioavailability problems connected to polyphenols. On the other hand, the presence of the esterase enzymes in the body guarantees the ester hydrolysis, which in turn frees the two molecules that make it up. Lipase-catalyzed esterifications afforded several derivatives of flavonoids glycosides, in green conditions. In this short note, pancreatic porcine lipase was firstly used as a cheap bio-catalyst, to synthesize oleoyl derivatives of quercetin in aglycone form. Results demonstrated how the enzyme acyl regioselective in position C-3, with high yields and easy purification processes

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Acacia dealbata Link, named Mimosa in Portugal, is an invasive hardwood species with potential for construction use, but research is limited. The available stock of small-diameter juvenile wood (sjw) logs can help reduce this gap, but tangential cracking at log ends challenges fastener connections. This study evaluated different treatments to control and reduce end-face cracking in sjw logs during air drying, an economical and environmentally friendly procedure. Extreme two-thirds of sixteen Mimosa logs were subjected to two treatments: one with longitudinal kerfs 15 mm deep along the length (2 and 3 kerfs) and the other with a hollow in the centre up to half the length (16 mm and 30 mm diameters). Over 219 days of air drying and compared with the central part, kerfing treatments significantly reduced outer wood tangential cracking (p &lt; 0.001), with the 3-kerf also reducing crack numbers (p &lt; 0.05) but increasing significantly cracks near the pith (p &lt; 0.01). The 30 mm central hollow significantly reduced central perforation cracking (p &lt; 0.05). Results suggest that a combined treatment approach could help mitigate cracking, enhancing the suitability of wild Mimosa logs for construction use.

In recent years, the emergence of cancer drug resistance is one of the crucial tumor hallmarks which is supported by the level of genetic heterogeneity and complexities at cellular levels. Oxidative stress, immune evasion, metabolic reprogramming, overexpression of ABC transporters and stemness are among the several key contributing molecular and cellular response mechanisms. Topo-active drugs, e.g., doxorubicin and topotecan, are clinically active and are utilized extensively against a wide variety of human tumors and often results in the development of resistance and failure to therapy. Thus, there is an urgent need for an incremental and comprehensive understanding of mechanisms of cancer drug resistance specifically in the context of topo-active drugs. This review delves into the intricate mechanistic aspects of these intracellular and extracellular topo-active drug resistance mechanisms and explores use of potential combinatorial approaches by utilizing various topo-active drugs and inhibitors of pathways involved in drug resistance. We believe that this review will help guide basic scientists, pre-clinicians, clinicians, and policymakers toward holistic and interdisciplinary strategies that transcend resistance, renewing optimism in the ongoing battle against cancer.

We report the development of an extrinsic self-healing coating system that shows no fluorescence from the intact coating, yellowish fluorescence in cracked regions, and greenish fluorescence in healed regions, thus allowing the separate monitoring of cracking and healing of coatings. This fluorescence monitoring self-healing system consisted of a top coating, an epoxy matrix resin containing mixed dye-loaded in single microcapsule. The dye-loaded microcapsules consisted of a poly(urea-formaldehyde) shell encapsulating a healing agent containing MAT-PDMS and styrene, a photo-initiator and a mixture of two dyes, one that fluoresces only in the solid state (DCM) and a second that fluoresces dramatically increased in the solid than solution state (4-TPAE). A mixture of the healing agent, photo-initiator and the two dyes was yellow due to fluorescence from DCM. On UV curing of this mixture, however, the color changed from yellow to green and the fluorescence intensity increased due to fluorescence from 4-TPAE in the solid state. When a self-healing coating embedded with microcapsules containing the DCM/4-TPAE dye mixture was scratched, the damaged region exhibited a yellowish color that changed to green after healing. Thus, the self-healing system reported here allows the separate monitoring of cracking and healing based on changes in fluorescence color.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

This study investigates the stress corrosion cracking (SCC) behavior of type 316L stainless steel (SS316L) produced with sinter-based material extrusion additive manufacturing (AM). This technology has been shown to produce SS316L with microstructures and mechanical properties comparable to its wrought counterpart in the annealed condition. However, despite plenty of research on SCC of SS316L, little is known about SCC in sinter-based AM SS316L. This study focuses on the influence of sintered microstructures on susceptibility to SCC initiation and crack-branching. Custom-made C-rings were exposed to different stress levels in acidic chloride solutions at various temperatures. To better understand the SCC behavior of SS316L, solution-annealed (SA) and cold-drawn (CD) wrought SS316L were tested for comparison. Results showed that sinter-based AM SS316L was more susceptible to SCC initiation than SA wrought SS316L but more resistant than CD wrought SS316L. Moreover, sinter-based AM SS316L showed noticeably better resistance to crack-branching than both wrought SS316L counterparts. The investigation was supported by comprehensive pre- and post-test microanalysis using light optical microscopy (LOM), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), and micro-computed tomography (micro-CT)

In this work, the recently proposed cracking elements method (CEM) is used for simulating the damaging processes of structures with initial imperfections. CEM is built in the framework of conventional FEM which is formally like a special type of finite element. The disconnected piecewise cracks are used for representing crack paths. Taking the advantages of CEM that both the initiations and propagations of cracks can be naturally captured, we numerically study the uni-axial compression tests of specimens with multiple joints and fissures, where the cracks may propagate from the tips, or from some other unexpected positions. Though uni-axial compression tests are considered, mainly tensile damage criteria are used in the numerical model. On one hand, the results demonstrate the robustness and effectiveness of the CEM while on the other hand, some drawbacks of the present model are demonstrated, showing the future work.

MoS2 has long been considered as a promising catalyst for hydrogen production. At present, there are many strategies to further improve its catalytic performance, such as edge engineering, defect engineering, phase engineering and so on. However, at present, there is still a great deal of controversy about the mechanism of MoS2 catalytic hydrogen production. For example, it is generally believed that the base plane of MoS2 is inert, but it has been reported that the inert base plane can undergo a transient phase transition in the catalytic process to play the catalytic role, which is contrary to the common understanding that the catalytic activity is only at the edge. Therefore, it is necessary to further understand the mechanism of MoS2 catalytic hydrogen production. In this article, we summarized the latest research progress on the catalytic hydrogen production of MoS2, which is of great significance for revisited the mechanism of MoS2 catalytic hydrogen production.

This short review is aimed at giving an overview of catalytic carbonylative double cyclization reactions, which are processes in which suitable organic substrates and carbon monoxide are sequentially activated by a promoting catalyst to afford the formation of two new cycles with concomitant incorporation of carbon monoxide as a carbonyl function into the final product. Paradigmatic examples of this powerful synthetic methodology, which allows the one-step synthesis of complex molecular architectures from simple building blocks using the simplest and readily available C-1 unit (CO) are illustrated and discussed. The review is divided into five sections: 1) Introduction; 2) Functionalized Olefinic Substrates; 3) Functionalized Acetylenic Substrates; 4) Functionalized Halides; 5) Conclusions and Future Perspectives.

Comprehensive understanding of tree characteristics and conditions holds paramount importance for the precise management of hazelnut orchards. It facilitates the determination of tree vigor, pruning requirements, phytosanitary interventions, and plant water consumption. The primary objective of this study was to explore, for the first time on a fruit tree with a bushy structure and across trees of four Italian distinct hazelnut cultivars, the efficacy of multispectral and thermal UAV (Unmanned Aerial Vehicle) technologies in assessing canopy attributes, vegetative growth, and predicting abiotic stresses. These technologies serve as tools for precision agriculture, enabling the computation of various indices such as the Normalized Difference Vegetation Index (NDVI) and crop water stress index (CWSI). The study of water content is of particular importance at this time, especially considering the increasing water stress levels in Europe as well as globally. While Red Green Blue (RGB) and thermal imagery collectively demonstrated superior performance in model reconstruction, the multispectral UAV remained more adept at characterizing size traits of hazelnut plants. Thermal images alone proved inadequate for accurately reconstructing hazelnut biometric characteristics. Furthermore, all indices were found to be cultivar-specific, underscoring the importance of conducting studies across different cultivars. The utilization of two UAVs, namely multispectral and thermal, facilitated the examination of the relationship between NDVI and CWSI across tree species.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

The KcsA is a prokaryotic potassium-oriented channel, which is sourced from the Streptomyces lividans soil bacteria. From extensive studies that have been carried over the KcsA potassium channel, it has been proved that various factors enable the gating and shuttling of the potassium ions into and out of the cells. Some of the factors include the different concentration of protons in the inside and outside membrane. The other factor is the existence of the selectivity filter equipped in the exit of channel pore, which enables the movement of the K⁺ ions. Not only are potassium ions present in the channel but also sodium ions. Potassium and sodium ions are the ions that are essential in the conductivity of a cell because of their charge. An intuitive idea about why K⁺ ions are at least 10,000 times more permeant than Na⁺ ions is presented in various entities. The hypothesis is that the selectivity ratio is probably related to the successive entry of Na⁺ ions, based on the premise that the ratio seems to be relevant to unpredictable quantities caused by Brownian corrosion of ions.

In "genome editing," a type of genetic engineering, DNA is added, taken away, or changed in an organism's genome. Biomedicine, biotechnology, and synthetic biology, just to name a few, have all gained a lot from how often this method is used. Before the editing process can start, a Double-Strand Breaks (DSB) must be made in the DNA at a specific gene. Researchers have made nucleases, which are sometimes called "molecular scissors," to fix this DSB. Transcription activator-like effector nucleases (TALENs), Zinc-finger nucleases (ZFNs), and homing endonucleases are all examples of protein targets that have been studied and changed. The last part gave an overview of these study projects and explained how to make Cas12a for specific uses. The applications of Cas12a have been extensively studied in recent years, but the protein still holds a lot of promise as a treatment and screening tool. In order to give a quick review of CRISPR-Cas12a and its uses, we will briefly talk about the structure and function of the different parts of the reaction pathway that lead up to the catalysis of the target DNA. Cas12a uses a multistep process to make sure that it is selecting the right DNA. This is a good trait for a device that changes the DNA because it makes it less likely that something bad will happen. Even though data shows that a new CRISPR RNAs (crRNA) molecule can stop Cas12a from randomly destroying ssDNA, it may still hurt the host cell while trying to change the genome. The action of Cas12a catalysis, which is a powerful tool for changing the genome, needs to be changed so that it can be more easily controlled and managed. Using what we know about how Cas12a works, we have made mutants that are less active on ssDNA and more active on dsDNA. So far, only Cas9 and Cas12a, which are both part of the CRISPR family, have been used to change the genome. Because of how similar and different these two endonucleases are, CRISPR can now be used for multiple scientific purposes. Cas12a is better than Cas9 because it makes double-strand breaks (DSBs) that favor Homology-Directed Repair (HDR) over Non-homologous end joining (NHEJ) and can change more than one copy of the genome at the same time. Both Cas9 and Cas12a are being changed to make them better at detecting Protospacer Adjacent Motif (PAM) than they are in their natural state. This will make it possible to start focusing on more genes.

Nucleolin is an RNA binding protein that is involved in many post-transcriptional regulation steps of messenger RNAs in addition to its nucleolar role in ribosomal RNA transcription and assembly in pre-ribosomes. Acetylated nucleolin was found to be associated with nuclear speckles and to co-localize with the splicing factor SC35. Previous nuclear pull down of nucleolin identified several splicing components and factors involved in RNA polymerase II transcription associated with nucleolin. In this report, we show that these splicing components are specifics of the pre-catalytic A and B spliceosomes, while proteins recruited in the Bact, C and P complexes are absent from the nucleolin interacting proteins. Furthermore, we show that acetylated nucleolin co-localized with P-SF3B1, a marker of co-transcriptional active spliceosomes. P-SF3B1 complexes can be pulled down with nucleolin specific antibodies. Interestingly, the alternative splicing of Fibronectin at the IIICS and EDB sites was affected by nucleolin depletion. These data are consistent with a model where nucleolin could be a factor bridging RNA polymerase II transcription and assembly of pre-catalytic spliceosome similarly to its function in the co-transcriptional maturation of pre-rRNA.

Radially polymerized dendritic compounds are nowadays an established polymer category next to their linear, branched and cross-linked counterparts. Their uncommon tree-like architecture is characterized by adjustable internal cavities and external groups. They are therefore exceptional absorbents and this attainment of high concentrations into their interior renders them ideal reac-tion media. In this framework they are applied in many environmentally benign implementa-tions. One of the most important among them is water purification though pollutant decomposi-tion. Simple and composite catalysts and photo-catalysts containing dendritic polymers and ap-plied in water remediation will be discussed jointly with some unconventional solutions and fu-ture prospects.

A series of polynuclear, dinuclear, and mononuclear Mo(VI) complexes were synthesized with the hydrazonato ligands derived from 5-methoxysalicylaldehyde and the corresponding hydrazides (isonicotinic hydrazide (H2L1), nicotinic hydrazide (H2L2), 2-aminobenzhydrazide (H2L3) or 4-aminobenzhydrazide (H2L4)). The metallosupramolecular compounds obtained from non-coordinating solvents, [MoO2(L1,2)]n (1 and 2) and [MoO2(L3,4)]2 (3 and 4), formed infinite structures and metallacycles, respectively. By blocking two coordination sites with cis-dioxo ligands, the molybdenum centers have three coordination sites occupied by the ONO donor atoms from the rigid hydrazone ligands and one by N atom of pyridyl or amine-functionalized ligand subcomponents from the neighbouring Mo building units. The reaction in methanol afforded the mononuclear analogues [MoO2(L1-4)(MeOH)] (1a-4a) with additional monodentate MeOH ligand. All isolated complexes were tested as catalysts for cyclooctene epoxidation using tBuOOH (TBHP) as an oxidant in water. The impact of the structure and ligand lability on the catalytic efficiency in homogeneous cyclooctene epoxidation was elucidated through theoretical considerations. Thus, dinuclear assemblies exhibited better catalytic activity than mononuclear or polynuclear complexes.

Two types of heterometallic (Fe(III),Na) silsesquioxanes [Ph₅Si₅O₁₀]₂[Ph₁₀Si₁₀O₂₁]Fe₆(O^2‒)₂Na₇(H₃O⁺)(MeOH)₂(MeCN)_4.5.1.25(MeCN), I, and [Ph₅Si₅O₁₀]₂[Ph₄Si₄O₈]₂Fe₆Na₆(O^2‒)₃(MeCN)_8.5(H₂O)_8.44, II, were obtained and characterized. X-Ray studies established distinctive structures of both products, with pair of Fe(III)-O-based triangles surrounded by siloxanolate ligands, giving fascinating cage architectures. Complex II proved to be catalytically active in the formation of amides from alcohols and amines, thus becoming a rare example of metallasilsesquioxanes performing homogeneous catalysis. Benzene, cyclohexane and other alkanes, as well as alcohols, can be oxidized in acetonitrile solution to phenol, the corresponding alkyl hydroperoxides and ketones, respectively, by hydrogen peroxide in air in the presence of catalytic amounts of complex II and trifluoroacetic acid. Thus, the cyclohexane oxidation at 20 °C gave oxygenates in very high for alkanes yield (48% based on alkane). The kinetic behaviour of the system indicates that the mechanism includes the formation of hydroxyl radicals generated from hydrogen peroxide in its interaction with diiron species. The latter are formed via monomerization of starting hexairon complex with further dimerization of the monomers.

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels considering Nigeria as case study. It is found that high solar radiation in Nigeria increases surface temperature of PV panel above 25oC of optimal operating temperature of PV panels. Redundant energy gain from incident solar energy is dissipated at the rear of PV panels as heat, which reduces the efficiency of PV panel. Cooling mechanism is needed to cool the PV panels to increase the efficiency. In this study we demonstrated a unique design of a bifunctional photovoltaic-thermal (PVT) system by employing heat exchanger at the rear of PV panel and water is used as a working fluid that is circulated through the heat exchanger to remove the excess heat. It is observed from the simulation results that Maiduguri peak annual electrical power output gives 1907kWh/kWp which is the highest, because of high solar radiation average of 727W/m2 in a year. And for Makurdi the peak annual electrical power output of 1542kWh/kWp while for Port Harcourt the peak power output of 1355kWh/kWp respectively. Interestingly, Polycrystalline Si-PV surface temperature decrease from 49.25oC to 38.38oC. Electrical power increased from 1526.83W to 1566.82W in a day and efficiency increase from 13.99% to 15.01%.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

In an analogous manner as occurred during the development of a connected metabolism that at some point reached characteristics associated with what is called ‘life’ ―due mainly to a catalytic closure phenomenon when chemicals started to autocatalyze themselves forming a closed web of chemical reactions― it is here proposed that cognition and consciousness (or features associated with them) arose as a consequence of another type of closure within the nervous system, the brain especially. Proper brain function requires an efficient web of connections and once certain complexity is attained due to the number and coordinated activities of the brain cell networks, the emergent properties of cognition and consciousness take place. Seeking to identify main features of the nervous system organization for optimal function, it is here proposed that while catalytic closure yielded life, neuroglial closure produced cognition/consciousness.

The mesoporous heteroatom molecular sieve MCM-41 bulk crystals with the crystalline phase were synthesized via a one-step hydrothermal method using an ionic complex as template. The ionic complex template was formed by interaction between cetyltrimethylammonium ions and metal complex ion [M (EDTA)]2- (M=Co or Ni ). The materials were characterized by X-ray diffraction, scanning electron microscopy, high-resolution transmission electron microscopy, N2 adsorption–desorption isotherms, and X-ray absorption fine structure spectroscopy. The results showed that the materials possess a highly ordered mesoporous structure with the crystalline phase and possess high uniform ordered arrangement channels. The structure is in the vertical cross directions with a crystalline size of about 12 µm and high specific surface areas. The metal atoms were incorporated into the zeolite frameworks in the form of octahedral coordinate and have a uniform distribution in the materials. The amount of metal complexes formed by metal ion and EDTA is an essential factor for the formation of the vertical cross structure. Comparing to Si-MCM-41, the samples exhibited better conversion, higher selectivity for cumene cracking.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

Electroless etching of semiconductors was elevated to an advanced micromachining process by the addition of a structured metal catalyst. Patterning of the catalyst by lithographic techniques facilitates the patterning of crystalline and polycrystalline wafer substrates. Galvanic deposition of metals on semiconductors has a natural tendency to produce nanoparticles rather than flat uniform films. This characteristic makes possible the etching of not only wafers but also particles with arbitrary shape. While it has been widely recognized that spontaneous deposition of metal nanoparticles can be used in connection with etching to porosify wafers, it is also possible to produced nanostructured powders. MACE can be controlled to produce (1) etch track pores with shapes and sizes closely related to the shape and size of the metal nanoparticle, (2) hierarchically porosified substrates exhibiting combinations of large etch track pores and mesopores, and (3) nanowires with either solid or mesoporous cores. This review discussed the mechanisms of porosification, processing advances and the properties of the etch product with special emphasis on the etching of silicon powders.

Dimers and oligomers of alkenes represent a category of compounds that are in great demand for diverse industrial sectors. Among the developing synthetic methods, the catalysis of alkene dimerization and oligomerization using transition metal salts and complexes is of undoubted interest for practical application. This approach demonstrates substantial potential, offering not only elevated reaction rates but also precise control over the chemo-, regio-, and stereoselectivity of the reactions. In this review, we discuss the data on catalytic systems for alkene dimerization and oligomerization. Our focus lies in the analysis of how the activity and chemoselectivity of these catalytic systems are influenced by various factors, such as the nature of the transition metal, the ligand environment, the activator, and substrate structure. Notably, the review particularly discusses the reaction mechanisms, encompassing metal complex activation, structural and dynamic features, and the reactivity of hydride intermediates, which serve as potential catalytically active centers in alkene dimerization and oligomerization.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

With the ever-growing emphasis on global decarbonization and rapid increases in the power density of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with Coefficient of Thermal Expansion (CTE) mismatch between components. The Al-Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as aerospace, automotive, consumer electronics, defense, EV and space. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al-Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17μm/(m·°C)) as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructure, physical and mechanical properties of these Al-Si alloys.

Two ligands, 1, 3-bis(4-carboxyphenyl)imidazolium chloride and 4, 4՛-bipyridine, were employed to prepare nickel and zinc azolium based MOFs, 1 and 2 by the mixed ligand solvothermal approach. The positively charged azolium moieties in the imidazolium linker resulted in a charged environment in the as-synthesized frameworks. As a result, 1 and 2 demonstrated preferential adsorption of CO2 over methane molecules in the gas phase adsorption due to the higher quadruple moment of CO2, which interacts more with the positively charged frameworks. Besides, in aqueous media, 1 and 2 exhibited incredible adsorption efficiency for anionic dyes. In the following, MOF 1 was metallated at the carbene site of the azolium linker to generate the novel heterogeneous catalyst 1-Pd, which was successfully applied for Sonogashira and Suzuki-Miyaura coupling reactions without losing its activity after three cycles.

In this research paper a novel Ultra Violet Photo Catalyst Oxidation (UVPCO) sensor for air and surface sanitization using Common Source (CS) amplifier is presented. The ultra violet photo catalysis is the process in which the highly reactive radicals like H+, OH-and peroxides ions are produced from air in the presence of the ultra violet radiation and photo catalyst. In this process, the free radicals outbreaks the bio aerosols like bacteria, fungus and volatile organic compounds (VOCs) and destroy them. The proposed system is relies on the fast operation of PCS which operates under sub-threshold conditions and reduced computation time. The properties of common source amplifier like very high voltage gain and input output resistance increased the sensitivity as well as stability of the circuit. The system is more user friendly and the outcomes of simulation are fairly in agreement with the theoretical estimation. Keywords: bio aerosol, Photo Catalytic Oxidation (PCO), hydroxyl, hydrogen peroxide, SPICE, surface sanitizer.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

Thermal infrared imagery provides temperature information on target objects, and has been widely applied in non-destructive testing. However, thermal infrared imagery is not always able to display detailed textures of inspected objects, which hampers the understanding of geometric entities consisting of temperature information. Although some commercial software has been developed for 3D thermal model displays, the software requires the use of expensive specific thermal infrared sensors. This study proposes a cost-effective method for 3D thermal model reconstruction based on image-based modeling. Two smart phones and a low-cost thermal infrared camera are employed to acquire visible images and thermal images, respectively, that are fused for 3D thermal model reconstruction. The experiment results demonstrate that the proposed method is able to effectively reconstruct a 3D thermal model which extremely approximates its corresponding entity. The total computation time for the 3D thermal model reconstruction is intensive while generating dense points required for the creation of a geometric entity. Future work will improve the efficiency of the proposed method in order to expand its potential applications to in-time monitoring.

The influence of hafnium metal (Hf) and sulfate ions (SO₄^-2) on the acidic properties of SiO₂ mesopores synthesized by a non-hydrothermal method was studied using the following characterization techniques; TG-DTG, XRD, BET, SEM, TEM, EDS, FTIR, n-butylamine titration, FTIR-pyridine, and alcohol dehydration. The incorporation of 3.6% mol of Hf during the silicate synthesis step caused the characteristic structural arrangement of MCM-41 to collapse. However, an increase in the acid strength of the catalyst of up to 315 mV was observed, with Brönsted and Lewis-type acid sites being mostly present therein. Furthermore, the acidity of Hf- and (SO₄^-2) -modified SiO₂ in the dehydration of ethanol and methanol was evaluated, resulting in a selectivity towards ethylene and dimethyl ether, respectively. Acid solids have enormous potential to produce important compounds for the chemical industry using alternative routes other than petrochemical processes. They also represent a significant advance for biorefineries.

This work shows the results obtained in the synthesis of srilankite nanoparticles, (Zr, Ti)O2, and TiO2 anatase, both catalysts presented an admix of phases, anatase/rutile, and srilankite/rutile, respectively. Their performance in the production of biodiesel through the esterification of oleic acid was evaluated. The catalysts were obtained using the sol-gel process and sulfated via the impregnation method. The samples were characterized using X-ray diffraction (XRD), scan electron microscopy (SEM), energy-dispersive X-ray spectroscopy (EDS) and Fourier-Transform Infrared Spectroscopy (FTIR) to analyze the properties in its crystalline structure, morphology, and chemical composition. Its efficiency during the esterification reaction was measured based on the decrease in free fatty acids (FFA). FFA, oleic acid was added at different weight percentages (1%, 3%, and 5% w/w). The time of reaction was 6 hours at 55 °C and the catalyst with better performance was the sulfated Srilankite/rutile, reaching a maximum conversion of up to 90%.

The processing of alkanes (the main components of natural gas) for obtaining of industrially important chemical products is one of the most urgent environmental problems, because the major share of raw materials are burned in torches. Therefore, the main goal of the work is the development of catalysts and conditions for obtaining of important petrochemical products from light alkanes. For the preparation of catalysts, Mo, Cr and Ga oxide catalysts as well as catalysts based on heteropoly compounds, supported on natural materials were used. The catalysts were prepared by the capillary impregnation method and used in oxidative conversion in a flowing unit while varying the process conditions. It has been determined that 5 and 10% MoCrGa catalysts are optimal for obtaining of liquid and gaseous products, and 1% catalyst is more favorable for the synthesis of gaseous products. Supported catalysts from heteropoly acid Н₃PW₁₂O₄₀ are highly active in oxidative dehydrogenation and cracking processes, which are concurrent. High activity is caused by dispersity of catalysts, formation of crystal hydrates and amorphous phase of heteropoly acid in a condition of interaction with carrier. Maximum yield of C₂H₄ - 35.2% at 973 K, C₃H₆ – 20.0% and C₄H₈ – 14.3% at 773 К were observed.

Cost-efficient catalyst for hydrogen evolution reaction (HER) and methanol oxidization reaction (MOR) is of great importance for industrial application. The alloying of platinum with cheap transition metal offers a great opportunity to reduce cost and enhance the electro-catalytic performance. Herein, we report a simple and green route to synthesize porous Pt-Cu catalysts, where Pt-Cu solid particles were first produced by using cuprous chloride (CuCl) nanoparticles as the template, followed by a dealloying treatment to obtain final porous product. The porous alloy nanoparticles show higher catalytic activity and superior stability for HER and methanol oxidation reaction, which is beneficial from the porous structure and synergetic effect between Pt and Cu.

Conversion of electromagnetic energy into magnetohydrodynamic energy occurs when the electric conductivity changes from negligible to finite values. This process is relevant during the epoch of reheating of the early Universe at the end of inflation and before the emergence of the radiation-dominated era. We find that conversion into kinetic and thermal energies is primarily the result of electric energy dissipation and that the magnetic energy plays only a secondary role in this process. This means that, since electric energy dominates over magnetic energy during inflation and reheating, significant amounts of electric energy can be converted into magnetohydrodynamic energy when conductivity emerges early enough, before the relevant length scales become stable.

In this paper we establish information theoretical bridges between 1) Thermal Heisenberg uncertainties $\Delta x \Delta p$ (at temperature $T$), and 2) LMC structural quantifiers. After having achieved such purpose, we determine to what an extent our bridges can be extended to both the semi classical and classical realms. Also, we find a strict bound relating a special LMC structural quantifier to quantum uncertainties.

Solidification cracking is a major obstacle when joining dissimilar alloys using additive manufacturing. In this work, location-specific solidification cracking susceptibility has been investigated using an integrated computational materials engineering (ICME) approach for a graded alloy formed by mixing P91 steel and Inconel 740H superalloy. An alloy derived from a mixture of 26 wt.% P91 steel and 74 wt.% Inconel 740H, with high configurational and total entropy, was fabricated using wire-arc additive manufacturing. Microstructure characterization revealed intergranular solidification cracks, which increased in length along with the build height. With inputs from experiments, such as secondary dendrite arm spacing, the DICTRA (diffusion-controlled transformations) module within the Thermo-Calc software was used to model location-specific solidification cracking susceptibility. The top region, with the highest cooling rate, has the highest solidification cracking susceptibility and is in good agreement with the experimentally observed crack length. From Scheil simulations, it was deduced that pronounced segregation of Nb and Cu within the cracks increased the solidification range by suppressing the solidus temperature. The overall solidification cracking susceptibility and freezing range was highest for the 26 wt.% P91 alloy amongst the mixed compositions between P91 steel and 740H superalloy, proving that solidification characteristics play a major role in alloy design for additive manufacturing.

Fluorescent labels, especially FRET probes, are promising tools for studying a number of bio-chemical processes. In this paper, we promoted 2 important applications of FRET probes (MUTMAC-R6G and FITC-R6G): i) the formation of micelles from surfactants of various natures and polymers (chitosan – fatty acid), as well as ii) monitoring of enzymatic activity with improved parameters (increased analytical signal and improved selectivity due to shift to the long-wavelength region). The formation of micelles is accompanied by the convergence of fluorophores in the hydrophobic micelle core by a distance closer than in the buffer solution, thus r/R0 (where R0 – Foerster radius) is chosen as an analytical signal of micelle formation, including critical micelle concentration (CMC) and critical pre-micelle concentration (CPMC). The CMC values calculated using FRET probes are in a good agreement with literature data. At the same time, the r/R0 function provides valuable information about the nature and mechanism of micelle formation. With the second analytical application of FRET probes, we considered the optimization of techniques for studying enzymatic activity. The enzyme catalyses the reaction with the release of a fluorescent product, the signal from which may not be enough for detection, or it may be quenched, for example, in the reverse micelles (AOT-octane). Here we have proposed a solution – a FRET probe containing a rhodamine 6G (R6G) acceptor, which allows us to monitor the enzymatic reaction selectively (in the red region, 550-600 nm), and obtain a significantly higher fluorescence yield (potentially from 10 to 250 times). Thus, we have demonstrated a high potential for the FRET probes application as indicators of micelle formation as well as for the study of the enzyme catalytic activity. In the future, the method developed has prospects for application in the visualization of the enzyme functioning in cells due to the shift of the fluorescence signal to the long-wavelength region with an increase in the signal selectivity to suppress autofluorescence.

Aquathermolysis is a promising method to upgrade heavy oil in reservoir conditions. However, application of catalysts can significantly promote transformation of the heavy fragments (resins and asphaltenes) and heteroatom-containing compounds of crude oil mixture into low-molecular-weight hydrocarbons. In this paper, the comparison study of the catalytic performance of the water-soluble metal salts such as NiSO4 and FeSO4 on the aquathermolytic upgrading of heavy oil samples produced from Ashal’cha reservoir was carried out at a temperature of 300 °C for 24 hours. Iron nanoparticles contributed to the highest viscosity reduction degree - 60% in contrast to the viscosity of the native crude oil sample. The viscosity alteration is reasoned by the changes in the group composition of heavy oil after catalytic (FeSO4) aquathermolysis, where the content of resins and asphaltenes were reduced by 17% and 7%, respectively. Moreover, the aquathermolytic upgrading of heavy oil in the presence of FeSO4 led to an increase in the yield of gasoline fraction by 13% and diesel fraction by 53%. The H/C ratio, which represents the hydrogenation of crude oil, increased from 1.52 (before catalytic upgrading) to 1.99 (after catalytic upgrading). The results of Chromatomass (GC-MS) and Fourier-infrared (FT-IR) spectroscopies confirmed the intensification of destructive hydrogenation of resins and asphaltenes in the presence of the water-soluble catalysts. According to XRD and SEM-EDX results, the metal salts are thermally decomposed during the aquathermolysis process into the oxides of corresponding metals and particularly sulfided by the sulfur-containing aquathermolysis products.

Minerals might have played critical roles for the origin and evolution of possible life forms on Mars. The study of the interactions between “building blocks of life” and minerals relevant to Mars mineralogy under conditions mimicking the harsh Martian environment may provide key insight into possible prebiotic processes. Therefore, this contribution aims at reviewing the most important investigations carried out so far about the catalytic/protective properties of Martian minerals toward molecular biosignatures under Martian-like conditions. Overall, it turns out that the fate of molecular biosignatures on Mars depends on a delicate balance between multiple preservation and degradation mechanisms often regulated by minerals, which may take place simultaneously. Such a complexity requires more efforts in simulating realistically the Martian environment in order to better inspect plausible prebiotic pathways and shed light on the nature of the organic compounds detected both in meteorites and on the surface of Mars through in situ analysis.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

In the quest for more efficient solar thermal systems, accurately determining the thermal emittance of low-emissive materials is crucial in determining the power losses. This paper describes the calorimetric method designed to precisely measure the thermal emittance of Selective Solar Absorbers (SSAs) to be used in High Vacuum Flat Plate Collectors (HVFPCs). The method's capability is demonstrated through the successful correction of thermal emittance values for copper samples of varying sizes, including dimensions down to 49 cm². Results highlight the method's potential to significantly reduce measurement errors associated with small-size and/or low-emittance samples, providing a path forward to improve the design and efficiency of SSAs. This research marks a significant step in advancing solar thermal technology by enabling emittance measurements with a precision better than 0.003, which is essential for the development of high-performance solar thermal absorbers. The method has also been applied to correct the thermal emittance value of SSA measured in previous measurement campaigns, and it allows a better estimation of the SSA efficiency conversion curve.

In order to utilize high-alumina coal gangue (HACG) as auxiliary cementitious admixture, it is of fundamental significance to thermally activating Al2O3 effectively in HACG and promoting formation of hydratable products containing Al2O3. In this paper, a new preparation technology is developed to make HACG auxiliary cementitious admixture by thermal activation of HACG-Ca(OH)2 (CH) mixture. HACG powders mixed with 20wt.% CH were calcined within a temperature range of 600-900oC, the thermal transformation and mineral phase formation were analyzed by thermogavimetric analyzer (TGA), X-ray diffractometer (XRD), scanning electron microscope (SEM) and energy dispersive X-ray spectrometer (EDS). The hydration reaction between activated HACG-CH mixture and cement was also investigated. HACG experienced a conventional transformation from kaolinite to metakaolin at 600oC and finally to mullite at 900oC. However, CH underwent an unexpected transformation process from CH to CaO, then to CaCO3, and finally to CaO again with increasing calcining temperature. These substances states were associated with dehydroxylation of CH, chemical reaction between CaO and CO2 generating from combustion of carbon in HACG, and decomposition of CaCO3, respectively. It is the formation of a large amount of CaO above 800oC that favors the formation of hydratable products containing Al2O3 in the calcining process and C-A-H gel in hydration process. The mechanical properties of HACG-cement mortar specimens were measured, from which the optimal calcination temperature for preparing HACG auxiliary cementitious admixture was determined to be 850oC. As compared with pure cement mortar specimens, the maximum 28-d flexural and compressive strength of HACG-cement mortar specimens increased by 5.4% and 38.2%, respectively.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

The annual energy matrix has been changing in the last years because of the necessity of less dependence on fossil fuels, which are running out on the planet. Therefore, a study was started to simulate the most efficient production of H2 through COMSOL Multiphysics®, as it is a gas that in the future will be essential to supply the world's energy necessities, due to its easy to get and insert in piped gas pipes. From this study, we were able to present an optimization of parameters that presents good indications of how to obtain efficient hydrogen production in an idealized reactor.

The post-weld heat treatment (PWHT) cracking susceptibility of a coarse grain heat-affected zone (CGHAZ) in SA213-T23 (2.25Cr-1.6W steel), used for boiler tubes employed in thermal power plants, was investigated using a Gleeble thermal cycle simulator. The PWHT cracking susceptibility test was performed at 650℃, 700℃ and 750℃, and it can be judged that the lower the reduce of area, the more susceptible it is to PWHT cracking. The results of the test also showed higher cracking susceptibility at 650℃ and 700℃, mostly involving intergranular fracture, while at 750℃, transgranular fracture was exhibited. Therefore, the PWHT cracking susceptibility is considered to be closely related to grain boundary. The microstructure of the simulated CGHAZ and PWHT at 650℃, 700℃and 750℃ was observed after etching with nital and alkaline sodium picrate etchants. Alkaline sodium picrate etched microstructures showed a white band at the grain boundary at 650℃, 700℃ and 750, that did not appear in nital etching. Analysis of the white band using EPMA, TEM and nanoindentation revealed that it was intergranular ferrite depleted with C, W and Cr as compared to that in the matrix. Based on these results, we investigated the mechanism of intergranular ferrite formation during PWHT and its effect on PWHT cracking susceptibility at 650℃, 700℃ and 750℃.

Graphene foam prepared by chemical vapor deposition method is a promising thermal interfacial material. However, the thermal properties of graphene foam highly depend on the experimental fabrication conditions during the chemical vapor deposition process. Aiming to reveal how to prepare the appropriate graphene foam for the various thermal management scenarios, the influence of experimental conditions on thermal properties of graphene foam is investigated. Furthermore, the contribution of thermal conductivity and thermal radiation to the effective thermal coefficient of graphene foam is carried out for comparison. Research results show that, the porosity and the cross-section shape of struts of growth template are two critical factors to affect the thermal transport of graphene foam, especially with the increase of temperature. In addition, the deposition time of graphene determines the wall thickness and affects the thermal conductivity directly. The thermal radiation contributes more than thermal conductivity when the temperature climbs continuously. Comparatively, the effective thermal coefficient of graphene foam composite with high porosity and circular shape struts is much superior to others at high temperature. The research findings can provide important guidance for the graphene foam fabrication and its applications in the field of thermal management.

Multilayer absorbers based on Cr2O3 and Cr, designed to improve the Solar-to-thermal conversion efficiency at mid temperatures in high vacuum flat thermal panel, are fabricated via sputtering deposition on bulk copper substrates and characterized by thermal and optical analysis. The refractive index of the single layers has been measured and used to estimate absorber thermal efficiency at the operating temperatures. Multilayers have been produced via sputtering deposition on bulk copper substrates. The absorber multilayers can be 10% more efficient than the commercial alternative at 250 °C operating temperatures, reaching 380 °C stagnation temperature without Sun concentration. The thermal stability has been checked at temperature of 400 °C in vacuum for four hours. High vacuum flat thermal collectors, equipped with the produced selective solar absorbers can obtain unprecedented performances and can give important contribution to the energy transition from fossil fuels to renewable energy for efficient heat production.

Plastics are highly beneficial for the day-to-day activities of human beings; however, their decomposition is limited due to their strong covalent bonding. The concept of degradation of these big molecules into smaller ones or monomers was attempted by several researchers in the preceding decades with limited success. Pyrolysis is one of the ideas used to convert plastics into fuel, rather than small molecules, compared to the crowded structure of polymers. Among these plastics, low-density polyethylene (LDPE) is largely used as carry bags throughout the world, and, herein, the results of catalytic pyrolysis of the conversion of LDPE into fuel are reported. Different dosages of zinc oxide (ZnO) were used as a catalyst to do the pyrolysis at a specific temperature in a batch reactor specially designed at our laboratory. 0.6 g of ZnO was found to be the optimal dosage for a 50 g waste LDPE batch to get the maximum oil yield. The yielded oil was analyzed chemically through Fourier transform infrared spectroscopy (FTIR) and Reformulyzer M4 Hydrocarbon Group Type Analyzer. Evaluation of physical and chemical exergy along with exergetic efficiency of the process was done.

The TREX1 exonuclease degrades DNA to prevent aberrant nucleic acid sensing through the cGAS-STING pathway, and dominant Aicardi-Goutières Syndrome type 1 (AGS1) represents one of numerous TREX1-related autoimmune diseases. Monoallelic TREX1 mutations were identified in patients showing early-onset cerebrovascular disease, ascribable to small vessel disease, and CADASIL-like neuroimaging. We report the clinical-neuroradiological features of two patients with AGS-like (Patient A) and CADASIL-like (Patient B) phenotypes carrying the heterozygous p.A136V and p.R174G TREX1 variants, respectively. Genetic findings, obtained by a customized panel including 183 genes associated with monogenic stroke, were combined with interferon signature testing and biochemical assays to determine the mutations’ effects in vitro. Comprehensive studies revealed no pathological impact on TREX1 enzymatic function for the p.A136V variant. The p.R174G variant modestly altered exonuclease activity consistently with perturbation of substrate interaction rather than catalysis, which represents the first robust enzymological data for a TREX1 variant identified in a CADASIL-like patient. In conclusion, functional analysis allowed us to interpret the impact of TREX1 variants on patients’ phenotypes. Whilst Patient A’s manifestations are not related to p.A136V variant, Patient B’s phenotype is likely related to the p.R174G variant. Further functional investigations of TREX1 variants found in CADASIL-like patients are warranted to establish a causal link and interrogate the molecular disease mechanism.

The ordered Ca3TaGa3Si2O14 and disordered La3Ga5SiO14 crystals of the lantangallium silicate family were grown by the Czochralski method. The independent coefficients of thermal expansion of crystals αc and αa were determined by X-ray powder diffraction based on the analysis of X-ray diffraction spectra measured in the temperature range of 25÷1000°C. It is shown that in the temperature range of 25÷800°C the thermal expansion coefficients are linear. At temperatures above 800°C there is a nonlinear character of the thermal expansion coefficients associated with a decrease in the Ga content in the crystal lattice of the lantangallium silicate family crystals.