The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

This study assesses Human Thermal Comfort in two selected areas: a Green Infrastructure (GI) area represented by a garden and a high-rise building area, in the Central Business District (CBD) of Melbourne, Australia. Three-dimensional microclimatic modelling software, ENVI-met version 4 was used to simulate the microclimate. The indices of Predicted Mean Vote (PMV), Physiological Equivalent Temperature (PET) and Universal Temperature Climate Index (UTCI) were used to quantify the level of thermal comfort in the research areas. The simulation results showed that at midday, the difference in temperature between the garden area and the high-rise building area was approximately 1°C. Increasing temperatures at midday led to a change in the level of thermal comfort for both the areas, even though it was not significant. In general, the thermal perception in the GI area was slightly ‘cooler’ than in the high-rise building area. The results of the study indicated the important role of GI in improving the thermal comfort in urban areas.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

Titania is one of the most comprehensively studied nanostructures due to its widespread applications in production of catalytic, gas- sensing and corrosion- resistance materials [1]. M-polynomial of nanotubes has been vastly investigated as it produces many degree-based topological indices which are numerical parameters capturing structural and chemical properties. These indices are used in the development of quantitative structure-activity relationships (QSARs) in which the biological activity and other properties of molecules are correlated with their structure like boiling point, stability, strain energy etc of chemical compounds. In this paper, we determine M-polynomials of single-walled titanium (SW TiO2) nanotubes and recover important topological degree based indices of them to theoretically judge these nanotubes. We also use Maple to plot surfaces associated to different types of single-walled titanium (SW TiO2) nanotubes.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

M-polynomial of different molecular structures helps to calculate many topological indices. A topological index of graph G is a numerical parameter related to G which characterizes its molecular topology and is usually graph invariant. In the field of quantitative structure-activity (QSAR) quantitative structure-activity structure-property (QSPR) research, theoretical properties of the chemical compounds and their molecular topological indices such as the Zagreb indices, Randic index, Symmetric division index, Harmonic index, Inverse sum index, Augmented Zagreb index, multiple Zagreb indices etc. are correlated. In this report, we compute closed forms of M-polynomial, first Zagreb polynomial and second Zagreb polynomial of Octagonal network. From the M-polynomial we recover some degree-based topological indices for Octagonal network. Moreover, we give a graphical representation of our results.

Background: In recent years, whole blood parameters and derivatives have been used as prognostic criteria in the course of the disease in various diseases. The prognostic nutritional index (PNI), the systemic immune-inflammation index (SII), the neutrophil-lymphocyte ratio (NLR) have been adapted as an indicator of inflammation and have been widely studied to define the severity of inflammation in some diseases. The aim of this study was to evaluate the relationship between parameters such as NLR, SII, PNI, controlling nutritional status (CONUT) score, nutritional risk index (NRI) and with immunonutrition status and disease activity in patients with ischemic stroke of small vessel, large vessel and other etiologies. Methods: We retrospectively evaluated the records of 1454 consecutive ischemic stroke patients hospitalized in the emergency department of Gaziosmanpasa Education and Research Hospital from 2019 to 2023. Results: Of the 1350 SVO patients included in the study, 58.8% had small vessel, 29.3% had large vessel and 11.9% had other etiologies. There was a significant difference between the 3 etiology groups for PNI and CONUT. The median PNI was 47.03 (41.33-52.85) in the other etiology group, 35.29 (33.69-37.25) in the small vessel group, and 34.11 (30.23-36.87) in the large vessel group. The CONUT median was 5(5-6) in the small vessel group, 5(4-6) in the large vessel group and 4(4-4) in the other etiology group. In addition, CONUT and PNI were also found to be independent risk factors for death. A negative significant correlation was observed between PNI and NLR (r:-0.692), SII (r:-0.591), CONUT (r:-0.685). Significant correlations were observed between CONUT and NLR (r:0.402), SII (r:0.312). Conclusion: PNI and SII were significantly associated with disease activity. PNI, CONUT and NRI as a more accurate prognostic indicator of nutritional status in patients with ischemic stroke of small vessel, large vessel and other etiologies. NLR and SII may be important predictive markers in the course and prognosis of stroke.

Drought affects human and natural systems, human and animal life and health, and socioeconomic activities. Drought consequences depend on its type and class, but also on the preparedness and resistance of communities to this climate disturbance. In the last decades, droughts accounted for about 16% of the total number of disasters but were responsible for 95% of the number of deaths and 26% of economic losses in Africa. This study aims to assess the drought regime in Southern Africa based on drought and vegetation indices. The SPI and SPEI were calculated at different timescales, using ERA5 data for the 1971 – 2020 period. The spatiotemporal distribution of drought descriptors was analyzed and compared with the patterns of the NDVI, EVI and VCI vegetation indices. The results reveal (i) the occurrence of droughts of various classes and at different timescales throughout the study period and region, (ii) high spatial variability in the number, duration, severity and intensity of drought, which tends to decrease with increasing timescale, (iii) high spatial-temporal agreement between drought and vegetation indices that confirm the dryness of vegetation during drought. These results aim to support policymakers in defining legislation to manage drought and water resources.

Detecting and monitoring changes in soil salinity through remote sensing provides an opportunity for field assessment in regions where on-site measurements are limited. This investigation, carried out in Siwa Oasis, Egypt, aimed to assess the efficacy of several soil salinity indices derived from Landsat 5 and 7 satellite images. To achieve this, 56 on-site ground measurements were utilized for evaluation purposes. The study aimed to improve the correlation between EC and index values and explore the relationship between salinity and changes in land cover. Eleven spectral indices were calculated for nine scenes captured in different months from August to December. The first approach involved stacking the data to identify the index with the strongest correlation with ground EC values, without the need for complex analysis or EC value ranging. In the second approach, the ground EC measurements were classified into seven different salinity categories, and the correlation coefficient was calculated between each index and each salinity category. The third approach analyzed the data temporally, considering different salinity levels. Lastly, a spatial correlation analysis was conducted between EC and index values in the fourth scenario. The initial approach revealed a weak correlation due to substantial variation in EC values. However, the SI index demonstrated the highest correlation coefficient of 0.38. In the second scenario, the S2 index exhibited the highest correlation of 0.96 for moderate salinity samples. The third scenario showed that the S1 index achieved the highest correlation value of 0.99 for moderately saline areas. In the fourth scenario, the SI index exhibited the strongest correlation among all four ponds with correlation coefficients of 0.23, 0.23, 0.18, and 0.61. Notably, the correlations observed in the second and third scenarios demonstrated higher correlation coefficients compared to both the first and fourth scenarios. The study highlighted significant variations in EC levels related to land cover types and pond elevation. Additionally, remote sensing methods detected a 48% increase in total vegetated area over 17 years, showing the potential of remote sensing techniques in salinity monitoring for expanding agriculture and improving land management.

This research is dedicated to a comprehensive examination of the strengths and weaknesses inherent in the legal and institutional measures designed to protect cultural heritage in the Republic of Serbia from the adverse effects of natural disasters, including earthquakes, landslides, rockfalls, floods, torrents, storms, hail, and forest fires. The study aims to identify the primary challenges and shortcomings within the existing legal and institutional framework, while also pinpointing and analyzing best practices and potential improvements for the protection system. This research posits a preliminary hypothesis suggesting that challenges may exist within the legal and institutional framework for the protection of cultural heritage in the Republic of Serbia, potentially limiting effective response and recovery following natural disasters. This hypothesis will be further developed and adapted based on the analysis of available data. Data collection for this research was conducted through semi-structured interviews with experts and an in-depth analysis of existing documentation. By conducting interviews with experts in the field, the research seeks to gather critical data and insights that will enhance the understanding of these issues and contribute to formulating viable solutions. The analysis and processing of data were carried out using ATLAS.ti software, which facilitated a comprehensive and systematic examination of the collected qualitative information. Furthermore, an assessment of the current capacity of institutions to respond rapidly and effectively to natural disasters that pose a threat to cultural heritage is a key component of the study. The ultimate goal is to develop recommendations that will fortify the legal and institutional framework, thereby bolstering the resilience of cultural heritage sites in Serbia against future natural disasters. The results of the research, highlight significant deficiencies in the legal framework, inadequate institutional capacities and resources, as well as a lack of proper training for crisis response. The need for improved inter-institutional cooperation and the development of technical-logistical resources is emphasized. This paper represents a significant contribution to the understanding and enhancement of the cultural heritage protection system, providing a foundation for further research and strategy development in this area.

Emergency Medical Response Systems (EMRS) play a vital role in delivering medical aid during disasters. In Serbia, these systems encounter several obstacles due to economic limitations, scarce resources, and ongoing healthcare reforms, all of which affect their performance. This study focuses on examining the risk factors and effectiveness of Serbia's EMRS, identifying systemic issues, and proposing enhancements to improve emergency preparedness for disasters. A survey was conducted across healthcare institutions in Serbia to gather comprehensive insights. The survey explored various aspects, including organizational structures, resource distribution, communication systems, and the speed of emergency responses. Statistical methods such as Pearson's correlation, multivariate regression analysis and chi-square tests were utilized to interpret data collected from 172 healthcare institutions. The multivariate regression analysis of EMS organization identified that factors such as the structuring of working hours and shift patterns are significant predictors, contributing to small but meaningful variations in various EMS outcomes. In contrast, other factors, such as financial resources and the availability of ambulance vehicles, showed more targeted significance depending on the specific EMS aspect being analyzed. Institutions with written mass casualty plans and procedures demonstrate superior effectiveness in EMS activities, excelling in resource allocation, operational continuity, and emergency preparedness, particularly through enhanced coordination and specialized systems for managing large-scale emergencies. The findings highlighted notable disparities in how EMRS are organized, with only 46% of institutions having specific emergency departments. Resource limitations were evident, as many facilities operated with minimal staff and outdated equipment. The communication systems revealed weaknesses, with just 54% having established protocols for handling emergency calls. Response times frequently surpassed international standards, which negatively affected patient outcomes. Additionally, the study found training deficiencies, with 68% of participants expressing a need for further education. Serbia’s EMRS are significantly impacted by systemic issues such as insufficient funding, disjointed service delivery, and inadequate training. Overcoming these challenges necessitates a comprehensive approach that includes boosting financial support, implementing standardized protocols, and fostering enhanced collaboration across different sectors.

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

With the development of the energy sector based on renewable primary sources, structural changes are emerging for the entire national energy system. Initially, it was estimated that energy generation based on fossil fuels would decrease until its disappearance. However, the evolution of CO2 capture capacity leads to a possible coexistence for a certain period with the renewable energy sector. The paper develops this concept of coexistence of the two systems, with the positioning of green hydrogen not only within the renewable energy sector but also as a transformation vector for carbon dioxide captured in the form of synthetic fuels such as CH4 and CH3OH. The paper also analyzes the economic aspects related to price differences for energy produced in the two sectors, as well as their interconnection. The technical aspect, as well as the economic one, for storage through various other solutions besides hydrogen, has been highlighted. The development of the renewable energy sector and its demarcation from the fossil fuel energy sector, even with the transcendent vector represented by green hydrogen, leads to the deepening of dispersion aspects between the electricity sector and the thermal energy sector, a less mentioned aspect in current works but of great importance.

Although vitamin D deficiency has been correlated with an increased risk of cardiovascular disease (CVD), there are few data on the association between 25-hydroxyvitamin D (25(OH) D) and atherogenic indices predictive of CVD. This study aimed to investigate the relationship of vitamin D status with lipid profile and atherogenic indices in adult women in Morocco. Three hundred healthy women, aged 18 to 50 years, from Meknes were included. Fasting 25(OH) D and lipid concentrations were determined using a one-step electrochemiluminescence-based immunoassay and an enzymatic method, respectively. Atherogenic indices (Atherogenic index of plasma (AIP), non-HDL cholesterol (Non-HDL-C), Atherogenic coefficient (AC), Castelli risk indices I and II (CRI-I and II), and CHOLIndex (CI)) were calculated using conventional lipid parameters. Logistic regression models and operating characteristic curve (ROC) analysis were used to assess the relationship of the variables and estimate the threshold of 25(OH) D levels associated with high atherogenic indices. 25(OH) D below 20 ng/ml was significantly associated with an enhanced risk of hypertriglyceridemia and elevated values of AIP, AC, Non-HDL-C, and CRI-I with an OR (95% CI) of 4.904 (1.856-12.959); 3.637(2.149-6.158); 3.589(1.673-7.700); 2.074(1.215-3.540), and 2.481(1.481-4.123), respectively. According to ROC analysis, the likelihood of hypertriglyceridemia and high values of AIP, AC, Non-HDL-C, and CRI-I were associated with 25(OH)D thresholds ≤15.15 ng/ml, ≤ 17.5 ng/ml, ≤ 19.8 ng/ml, ≤ 20.1 ng/ml and ≤ 19.5 ng/ml, respectively, all p < 0.01. Based on atherogenic indices, this study indicates that vitamin D below 20 ng/ml may increase the risk of cardiovascular disease in adult women. Additional health efforts are needed to raise awareness among women and healthcare providers in preventing and controlling cardiovascular risk factors.

(1) Background: Depressional wetlands are highly vulnerable to changes in temperature and rainfall, affecting littoral vegetation, thus HydroGeoMorphic (HGM) wetland types. This study aimed to assess the utility of Sentinel-2A vegetation indices in enhancing delineation and sub-classify depressional HGM types. (2) Methods: We sampled 84 pairs of four vegetation indices from 10x10m plots along 14 belt transects in eight depressional wetlands in Mpumalanga, South Africa. We evaluated vegetation index differences between and within wetlands, focusing on lit-toral gradients. (3) Results: Significant differences (Bonferroni p

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

Based on literature data, an analysis was conducted on the thermodynamic and kinetic dependencies of the thermal decomposition of methane. Course of this process was analysed for both thermal and thermal-catalytic conditions. The elementary reaction, i.e. the synthesis of methane from its elements, including its reversibility, was used as the basis for the for considerations on the kinetic model. The conversion degree was adopted as the kinetic parameter (kinetic variable) since this measure is essential for determining the amount of carbon deposit formed and thus closing the mass balance of this process. Several different kinetic models for the elementary reaction were analysed to determine how do they relate in regard to the constant of the reaction rate. It was determined that regardless of whether the process is catalytic or purely thermal, for temperatures t>900°C, the influence of reversibility of the reaction, has negligible influence on the yield of hydrogen produced, and thus can be omitted from the kinetic models. Special attention was given to iron-based catalysts, analysing the reactivity of Fe/C systems. It was demonstrated that the determined kinetic parameters satisfy the Kinetic Compensation Effect (KCE). Furthermore, by incorporating elements of Transition State Theory (TST), the existence of Entropy-Enthalpy Compensation (EEC) was highlighted. Based on these findings Authors show that through analysis of the changes in activation energy (E=20–421 kJ·mol-1) only an estimate of the optimal process conditions can be found, because the isoconversional temperature is also dependent on the way in which the reaction is conducted (T_{iso}=1200-1450K\ >\ \ T_{eq}). In other words, it was found that strong influences of such factors as T, P, etc. can locally compensate each other. Finally, it was also shown that the relations between KCE and EEC complement each other, which is confirmed by the determined average activation entropy at the isokinetic temperature (∆SB= -275.0 J·(mol·K)-1).

Objective. The present study examined the potential use of computed tomography panoramic mandibular indices on cone beam CT (CBCT) for the assessment of bone density in postmenopausal women with low bone mass. Study design. We enrolled 104 postmenopausal women who performed dual energy X-ray absorptiometry (DXA) using a DXA scanner and mental foramen region CBCT using NewTom VGi EVO Cone Beam 3D system. We assessed the relationship between DXA parameters: lumbar, femoral neck and total hip T score, bone mineral density (BMD), and lumbar trabecular bone score (TBS) and the panoramic mandibular indices: computed tomography mandibular index superior (CTI(S)), computed tomography mandibular index inferior (CTI(I)) and computed tomography mental index (CTMI). Results. We found important correlations between the CTI(I), CTI(S) and CTMI and bone mass, quantitative evaluated as BMD and T-score and also quality using TBS score. Conclusion. CBCT measured indices CTI(S), CTI(I), CTMI are useful in assessing patients with low bone mass.

Recently two new degree concepts have been defined in graph theory: ev-degree and ve-degree. Also the ev-degree and ve-degree Zagreb and Randić indices have been defined very recently as parallel of the classical definitions of Zagreb and Randić indices. It was shown that ev-degree and ve-degree topological indices can be used as possible tools in QSPR researches . In this paper we define the ve-degree and ev-degree Narumi–Katayama indices, investigate the predicting power of these novel indices and extremal graphs with respect to these novel topological indices. Also we give some basic mathematical properties of ev-degree and ve-degree Narumi-Katayama and Zagreb indices.

Our aim is at three feels: i) study safe haven properties of sectoral CDS; ii) study hedging effectiveness and measure the diversification benefits of introducing them in both Conventional and Islamic stock markets portfolios and iii) compare these results with VSTOXX, Gold and Bitcoin indices. To do this, we estimate time varying hedge ratio using (A)DCC and GOGARCH models and then deduce hedging effectiveness.. We follow the same methodology for each sub-period and each refit to test the effect of bubble crypto currency and COVID-19 pandemic on hedging effectiveness. Empirical results show the superiority of industrial CDS sectoral index to hedge both conventional and Islamic stock markets whether long or short term despite that their performances were reduced slightly during the second and third periods. VSTOXX and Others sectoral CDS indices offers Hedging performances that are generally better than Bitcoin and gold.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

A method for estimating river water surface elevation (WSE) from Landsat imagery using the river inundation area - water surface elevation (RIA-WSE) rating curve constructed from the U.S. Geological Survey Topobathymetric Elevation Model (TEM) data was developed and tested at six gauging stations along the upper Mississippi River. The Otsu's automatic threshold selection algorithm was employed for the image classification and estimation of inundation areas within each pre-defined polygon around each gauging station. In addition to the commonly used green-band based water indices, Landsat 8 and 9 OLI's ultra-blue, blue, and red band-based water indices were also tested in this study, which resulted in twenty different water indices: NDWIv (Normalized Difference Water Index), MNDWI1v and MNDWI2v (Modified Normalized Difference Water Index), AWEIsv (Automatic Water Extraction Index with shadow), and AWEInsv (AWEI without shadow), where v represents the visible light band used in the water index. At each station, about 60-80 Landsat 8 or 9 images during 2013-2023 were used for assessing the performances of the twenty water indices through comparing the estimated WSEs with the measured WSEs. Results showed that the ultra-blue or red band-based AWEIs yielded the most accurate estimations of WSEs among the twenty tested water indices.

Anaerobic digestion is a biological process that transforms high-strength organic effluents into biogas with multiple benefits. However, concurrent with organics' biological transformation, a liquid phase with a high solid content is also derived from this process. Valorizing this fraction is not an easy task if an agronomic application cannot be considered as a suitable option. The thermal valorization of this fraction allows for energy extraction, but also gives rise to additional capital investment and increases the energy demand of the global process. In addition, the thermal treatment of digestate has to deal with a mineralized material. The changes in organic matter due to anaerobic stabilization were studied in the present manuscript, by evaluating the thermal behavior of samples, activation energy and organic transformation using FTIR spectroscopy. Digested samples of a mixture composed of manure and glycerin (5% v/v) were studied. The stabilization caused a dramatic decrease in aliphatic compounds, greatly increasing the mineral content of the sample. Thermal valorization of digestates must consider the lower energy content and more complex structure of these materials, with higher content of lignin and protein-type compounds.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

The growing concerns about floods have highlighted the need for accurate and detailed precipitation data as extreme precipitation occurrences can lead to catastrophic floods, resulting in significant economic losses and casualties. Integrated Multi-satellitE Retrievals for the Global Precipitation Measurement (GPM-IMERG) is a commonly used high-resolution gridded precipitation dataset and is recognized as trustworthy alternative sources of precipitation data. The aim of this study is to comprehensively evaluate the performance of GPM IMERG Early (IMERG-E), Late (IMERG-L), and Run Final (IMERG-F) in precipitation estimation and their capability in detecting extreme rainfall indices over southwestern Iran during 2001-2020. The Asfezari gridded precipitation data which are developed using a dense of ground-based observation were utilized as the reference dataset. The findings indicate that the IMERG-F performs reasonably well in capturing many extreme precipitation events (defined by various indices). All the three products showed a better performance in capturing fixed and non-threshold precipitation indices across the study region. The findings also revealed that both IMERG-E and IMERG-L have problems in rainfall estimation over elevated areas showing values of overestimations. Examining the effect of land cover type on the accuracy of the precipitation products suggest that both IMERG-E and IMERG-L show large and highly unrealistic overestimations over inland water bodies and permanent wetlands. The results of the current study highlight the potential of IMERG-F as a valuable source of data for precipitation monitoring in the region.

Drought monitoring and early detection have improved greatly in recent decades through the development and refinement of numerous indices and indicators. However, a lack of guidance, based on user experience, exists as to which drought monitoring tools are most appropriate in a given location. This review paper summarizes the results of targeted user engagement and the published literature to improve the understanding of drought across North America, and to enhance the utility of drought monitoring tools. Workshops and surveys were used to assess and make general conclusions about the perceived performance of drought indicators, indices and impacts information used for monitoring drought in the five main Köppen climate types (Tropical, Temperate, Continental, Polar Tundra, Dry) found across Canada, Mexico, and the United States. In Tropical, humid Temperate, and southerly Continental climates, droughts are perceived to be more short-term (less than 6 months) in duration rather than long-term (more than 6 months). In Polar Tundra climates, Dry climates, Temperate climates with dry warm seasons, and northerly Continental climates, droughts are perceived to be more long-term than short-term. In general, agricultural and hydrological droughts were considered to be the most important drought types. Drought impacts related to agriculture, water supply, ecosystem, and human health were rated to be of greatest importance. Users identified the most effective indices and indicators for monitoring drought across North America to be the U.S. Drought Monitor (USDM) and Standardized Precipitation Index (SPI) (or another measure of precipitation anomaly), followed by the Normalized Difference Vegetation Index (NDVI) (or another satellite-observed vegetation index), temperature anomalies, crop status, soil moisture, streamflow, reservoir storage, water use (demand), and reported drought impacts. Users also noted the importance of indices that measure evapotranspiration, evaporative demand, and snow water content. Drought indices and indicators were generally thought to perform equally well across seasons in Tropical and the colder Continental climates, but their performance was perceived to vary seasonally in Dry, Temperate, Polar Tundra, and the warmer Continental climates, with improved performance during warm and wet times of the year. The drought indices and indicators, in general, were not perceived to perform equally well across geographies. This review paper provides guidance on when (time of year) and where (climate zone) the more popular drought indices and indicators should be used. The paper concludes by noting the importance of understanding how drought, its impacts, and indicators are changing over time as the climate warms, and by recommending ways to strengthen the use of indices and indicators in drought decision-making.

Topological indices have been used to modeling biological and chemical properties of molecules in quantitive structure property relationship studies and quantitive structure activity studies. All the degree based topological indices have been defined via classical degree concept. In this paper we define a novel degree concept for a vertex of a simple connected graph: S degree. And also we define S indices of a simple connected graph by using the S degree concept. We compute the S indices for well-known simple connected graphs such as paths, stars, complete graphs and cycles.

Fission-track modelling rests on etching, counting and measuring the lattice damage trails from uranium fission. The tools for interpreting fission-track data are advanced but the results are never better than the data. Confined-track samples must be an adequate size for statistical analysis, representative of the track population, consistent with the model assumptions and with the calibration data. Geometrical and measurement biases are understood and can be dealt with up to a point. The interrelated issues of etching protocol and track selection are however more difficult to untangle. Our investigation favours a two-step protocol. The duration of the first step is inversely proportional to the apatite etch rate, so that different apatites etch to the same Dpar. A long immersion reveals many more confined tracks, terminated by basal and prism faces. This allows consistent length measurements and permits to orient each track relative to the c-axis. Long immersion times combined with deep ion irradiation reveal confined tracks deep inside the grains. Provided it is long enough, the precise immersion time is not important if the effective etch times of the selected tracks are calculated from their measured widths. Then, whether the sample is mono- or multi-compositional, we can, post hoc, select tracks with the desired properties. The second part of the protocol has to do with the fact that fossil tracks in geological samples appear to be under-etched compared to induced tracks etched under the same conditions. This should be assumed if the semi-axes (l_C, l_A) of a fitted ellipse plot above the induced-track line. In that case an additional etch can increase the track lengths to a point where they are consistent with the model based on lab-annealing of induced tracks, a condition for valid thermal histories. Here too, it is possible to select a subset with effective etch times consistent with the model if the widths of confined tracks are measured along with their lengths and orientations.

Background/Objectives: The primary life-threatening complication in Spinal-bulbar muscular atrophy (SBMA) is ventilatory failure, which results from the weakening of the bulbar and respiratory muscles. However, systematic studies assessing respiratory function over the long-term have not been performed. The present study analyzes the longitudinal patterns of respiratory function tests over a follow-up of 11 years, aiming to identify any potential, sustained decline during this time. Furthermore, we explored possible correlations between respiratory function tests and clinical and biochemical serum indices. Methods: We collected data from 9 genetically confirmed SBMA patients and conducted spirometric measurements twice a year for eleven years. The spirometric data included maximum inspiratory pressure (MIP), maximum expiratory pressure (MEP), and forced vital capacity (FVC)]. Additionally, we measured serum biochemical indices and SBMA functional rating scale (SBMAFRS) for clinical analysis. Results: All three respiratory function tests showed a descending trend. A major decrease was observed for MEP (52%) and MIP (42%), while this was minor for FVC (25%). SBMAFRS score correlated with the three pulmonary function tests. MIP and MEP correlated with creatine phosphokinase and creatinine levels, and FVC correlated with serum level of transaminases. Conclusions: This longitudinal study shows a progressive decline of spirometric data throughout life in patients with SBMA. Spirometric measures relative to maximal strength of the respiratory muscles (MIP and MEP) may have a better predictive value for pulmonary and muscular decline than FVC.

The objective of this study was to investigate the impact of adding fermented herbal extracts (FHE) derived from mulberry leaf (Morus alba), Javanese turmeric (Curcuma xanthorrhiza), and fingerroot (Boesenbergia rotunda) to the diet of tiger shrimp (Penaeus monodon) on their growth, moulting performance, feed efficiency, and nutrient retention. The main feed used in this trial was a commercially manufactured pellet, then five different doses of FHE supplementation were used: 0 mg/kg feed (P0, control), 50 mg/kg feed (P1), 100 mg/kg feed (P2), 150 mg/kg feed (P3), and 200 mg/kg feed (P4). Weight gain, average daily gain, and length gain of shrimps fed P2 was significantly higher than that of those fed the control diet. Similar result was observed in moulting performance. The application of P2 showed superior results in enhancing the FE of cultured shrimp. Thus, the protein and energy retention of P. monodon was significantly better in P2 treatment groups. P0 had the lowest crude protein, while shrimp given P2 and P3 diets had the highest crude protein content of any treatment group. Based on the findings, it is recommended that the juvenile tiger shrimp diet contain 100 mg/kg of FHE for the best effects.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

The development of the finite element method (FEM) combined block polynomial interpolation with the concepts of finite difference formats and the variation principle. Because of this combination, FEM overcomes the shortcomings of traditional variation methods while maintaining the benefits of current variation methods and the flexibility of the finite difference method. As a result, FEM is an advancement above the traditional variation methods. The aim of the study is to experimentally determine the thermal behavior of two stomatognathic systems, one control and the other presenting orthodontic treatment by means of a fixed metallic orthodontic appliance, both being subjected to several thermal regimes. In order to carry out this experimental study, we examined the case of a female subject, who was diagnosed with Angle class I malocclusion. The patient underwent a bimaxillary CBCT investigation before initiating the orthodontic treatment. A three-dimensional model with fully closed surfaces was obtained by using the InVesalius and Geomagic programs. Like the tissues examined in the patient, bracket and tube-like components, as well as orthodontic wires, can be included to these models. Once it is finished and geometrically accurate, the model is exported to a FEM-using program, such as Ansys Workbench. The intention was to study the behavior of two stomatognathic systems (with and without a fixed metallic orthodontic appliance) subjected to very hot food (70 ⁰C) and very cold food (-18 ⁰C). From the analysis of the obtained data, it was concluded that, following the simulations carried out in the presence of the fixed metallic orthodontic appliance, significantly higher temperatures were generated in the dental pulp.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Financial stress can have significant implications for individuals, businesses, asset prices and the economy as a whole. This study examines the nonlinear structure and dynamic changes in the multifractal behavior of cross-correlation between the financial stress index (FSI) and four well-known commodity indices, namely Commodity Research Bureau Index (CRBI), Baltic Dry Index (BDI), London Metal Index (LME) and Brent Oil prices (BROIL), using multifractal detrended cross correlation analysis (MFDCCA). For analysis, we utilized daily values of FSI and commodity index prices from 16th June 2016 to 9th July 2023. The following are the most important empirical findings: (I) All of the chosen commodity market indices show cross correlations with the FSI and have notable multifractal characteristics. (II) The presence of power law cross-correlation implies that a noteworthy shift in FSI is likely to coincide with a considerable shift in the commodity indices. (III) The multifractal cross-correlation is highest between FSI and Brent Oil (BROIL) and lowest with LME. (IV) The rolling windows analysis reveals a varying degree of persistency between FSI and commodity markets. The findings of this study have a number of important implications for commodity market investors and policymakers.

In this paper, we give some upper and lower bounds for the multiplicative Randic index, reduced reciprocal Randic index, Narumi-Katayama index and symmetric division index a graph using solely the vertex degrees. Then we obtain upper and lower bounds for these indices for the complete graphs, path graphs and Fibonacci-sum graphs. Finally, we compared the bounds of these indices for a general graph and some special graphs.

Lake Chapala is a natural ecosystem of Mexico, declared Ramsar site, currently, is an area with importance in the agricultural sector, tourism, and important source of drinking water in the Metropolitan area of Guadalajara, considered as a thermo regulatory body. This study used tools such as Rhtest, as well as analyzing extreme climate indices using RClimdex. In addition, the relationship with the change in water surface of Lake Chapala was assessed through the NDWI index, using Landsat images, between 1985 and 2018. According to the obtained results, the signs of climatic variability are detected in the study region, which, directly affects the basin runoff and water levels in the lake, as well as, the factor of water overexploitation in the basin, so it is considered that the lake conditions mostly depend on the type of management that is given to the resource. Finally, the results will help the understanding of climate variability and its water resources influence of the Lerma Chapala basin, which will assist in future research.

The topological index is a numerical quantity based on the characteristics of various invariants or molecular graph. For ease of discussion, these indices are classified according to their logical derivation from topological invariants rather than their temporal development. Degree based topological indices depends upon the degree of vertices. This paper computes degree based topological indices of Bismuth Tri-Iodide chains and sheets with the help of M-polynomial.

In the study of QSAR/QSPR, due to high degree of predictability of pharmaceutical properties, the eccentric-connectivity index has very important place among the other topological descriptors, In this paper, we compute the exact formulas of eccentric-connectivity index and its corresponding polynomial, total eccentric-connectivity index and its corresponding polynomial, first Zagreb eccentricity index, augmented eccentric-connectivity index, modified eccentric-connectivity index and its corresponding polynomial for a class of phosphorus containing dendrimers.

The pursuit of materials that offer both wear comfort and protection for functional and protective clothing has led to the exploration of weft-knitted spacer structures. Traditional cushioning materials such as spacer fabrics and laminated foam often suffer from deformation under compression stresses, thus compromising their protective properties. This study investigates the enhancement of the force absorption, stress-strain and thermal properties of weft-knitted spacer fabrics with inlays. Surface yarns with optimal stretchability and thermal properties are used and combined with elastic yarns in various patterns to fabricate nine different inlay samples. The mechanical and thermal properties of these samples are systematically analyzed, including their compression, stretchability, thermal comfort and surface properties. The results show that the inlay spacer fabric exhibits superior compression properties and thermal conductivity compared to traditional laminated foam and spacer fabrics, while maintaining stretchability, thus providing a better performance than traditional fabrics for protective clothing and wearable cushioning products. This study further confirms that the type of inlay yarn and inlay structure are crucial factors that significantly influence the thermal, tensile and compressive properties of fabric. This research provides valuable insights into the design and development of advanced textile structures to improve wear comfort and protection in functional garment applications.

This study investigates the impact of vertical greenery systems (VGS) applied to heavyweight walls on indoor thermal conditions in a building module situated in the Mediterranean climate of Catania, Italy. Using dynamic simulations in TRNSYS, the research compares the thermal behavior of walls constructed from hollow clay blocks (Poroton) and lava stone blocks with a lightweight wall setup already in place at the University of Catania. The primary focus is on evaluating the VGS’s effect on reducing peak inner surface temperatures and moderating heat flux fluctuations entering the building. The findings indicate that adding a vertical greenery layer to heavyweight walls can decrease the peak inner surface temperature by up to 1.0°C compared to the same wall without vegetation. However, the greenery’s impact on mitigating heat flux fluctuations is less pronounced than in the case of the lightweight wall. This research underscores the potential of green facades in enhancing indoor thermal comfort in regions with climates similar to the Mediterranean, providing valuable insights for sustainable building design and urban planning.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

Vertex-degree-based (VDB) topological indices have been applied in QSPR/QSAR. As an important category, the general logarithmic VDB topological index $T_{lnf}(G)$, is defined as the summation of $ln{f(d(u),d(v))}$, where the summation over all $uv\in E(G)$. In this paper, we give the sufficient conditions for that (1) the path $P_{n}$ is the only tree with the minimal $T_{lnf}$; (2) the star $S_n$ is the only tree with the maximal and the minimal $T_{lnf}$, respectively. As applications, the minimal and maximal trees of some logarithmic VDB indices are determined.

Vegetation indexes help perform precision farming because they provide useful information regarding moisture, nutrient content, and crop health. Primary sources of those indexes are satellites and unmanned aerial vehicles equipped with expensive multispectral sensors. Reducing the price of obtaining such information would increase the availability of precision farming for small farms. Several studies have proposed deep neural network methods to estimate the indexes from RGB color images. However, these methods report relatively large errors for mature plants when highly non-linear relationships of images and vegetation indexes arise. One could apply multilayer random forest-based models (Deep Forests) to solve this problem, but the discriminative power of such models is limited: they cannot catch complex dependencies between image features. In this paper, we propose a method that combines ideas of deep forests, random forests of kernel trees, and global pruning of random forests to tackle the problem. As a result, the method considers the properties of objects with a complex structure: the presence of relationships between groups of features, displacement, and scaling of objects. The experimental results show that the proposed method outperforms neural network-based solutions in several datasets.

The organic material present at the same depth in the reservoir has the potential for conversion, as indicated by analyses conducted before and after combustion in the development of heavy oil. This paper examines the oxidation and pyrolysis reaction pathways of hydrocarbons, specifically benzaldehyde (C₇H₆O) and naphthalene (C₁₀H₈), before and after combustion using molecular dynamics simulations. The primary products formed under various temperature conditions include H₂O, HO₂, CO, and CO₂. The discussion includes the number of molecules, such as HO and H, as well as their temperature variations. The activating group functions as an electron donor, while the inactivating group serves as an electron acceptor. The oxidation and pyrolysis reactions of naphthalene and the synthesis pathway of benzaldehyde are also explored. The C-C dissociation pathway in the early stages of combustion and the process of C-C bond synthesis in the later stages of the reactions are investigated through dynamic simulations at different temperatures: 3000 K, 3500 K, and 4000 K, with a particular focus on the reaction network at 4000 K. The application of the molecular reaction dynamics method to heavy oil combustion research is the primary objective of this work. This study aims to provide a novel approach to investigating hydrocarbon conversion at high temperatures and offers recommendations for enhanced oil recovery.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

This pioneering study explores the geospatial and temporal patterns of natural and human-induced disasters from 1900 to 2024, providing essential insights into their global distribution and impacts. Utilizing the comprehensive international EM-DAT database, our analysis reveals significant trends and disparities in disaster occurrences and their widespread consequences. Results showed a dramatic escalation in both natural and man-made (technological) disasters over the decades, with notable surges in the 1991-2000 and 2001-2010 periods. A total of 25,836 disasters were recorded worldwide, of which 69.41% were natural disasters (16,567) and 30.59% were man-made (technological) disasters (9,269). The most significant increase in natural disasters occurred from 1961-1970, while man-made (technological) disasters surged substantially from 1981-1990. Seasonal trends reveal that floods peak in January and July, while storms are most frequent in June and October. Droughts and floods are the most devastating in terms of human lives, while storms and earthquakes cause the highest economic losses. The most substantial economic losses were reported during the 2001-2010 period, driven by catastrophic natural disasters in Asia and North America. Our research highlights Asia as the most disaster-prone continent, accounting for 41.75% of global events, with natural disasters making up 61.89% of these events. Oceania, despite experiencing fewer total disasters, shows a remarkable 91.51% of these as natural disasters. Africa is notable for its high incidence of man-made (technological) disasters, which constitute 43.79% of the continent's disaster events. Europe, representing 11.96% of total disasters, exhibits a balanced distribution but tends towards natural disasters at 64.54%. Examining specific countries, China, India, and the United States emerged as the most frequently affected by both natural and man-made (technological) disasters. The impact of these disasters has been immense, with economic losses reaching their highest during the decade of 2010-2020, largely due to natural disasters. The human toll has been equally significant, with Asia recording the most fatalities and Africa the most injuries. Particularly, the decade from 2001 to 2010 experienced the greatest economic losses, primarily driven by natural disasters in Asia and North America. These insights highlight the urgent need for tailored disaster risk management strategies that address the distinct challenges and impacts in various regions. By understanding historical disaster patterns, policymakers and stakeholders can better anticipate and manage future risks, ultimately safeguarding lives and economies.

Non-destructive, accurate, and timely approach for crop yield prediction at field scale is vital for precision agriculture. This study aimed to investigate the appropriate wavelengths and their combinations to explore the new SIs derived from UAV hyperspectral images in predicting yield during the growing season of spring maize. The best wavelengths and new SIs, including the difference spectral index, ratio spectral index, and normalized difference spectral index forms, were obtained by the contour maps constructed by the coefficient of determination (R2) from the linear regression models between the yield and all possible SIs screening out from the 450-950 nm wavelengths. The results showed that the most sensitive wavelengths were 640-714 nm at WJQ, 450-650 nm and 750-950 nm at SKS, and 450-700 nm and 750-950 nm at FJJ. The new SIs established here were different across the three experimental fields, and their performance on maize yield prediction were generally better than that of the published SIs. In addition, the new SIs presented different response to various N fertilization levels. This study demonstrated the potential of exploring new spectral characteristics from remote sensing technology for predicting field-scale crop yield in spring maize cropping systems before harvest.

The socioeconomic sectors increasingly rely on prompt and affordable tools to predict climatic conditions. This study uses a decision tree classifier model to identify similar monthly ENSO 3.4 indices from March 2001 to February 2011 through monthly historical ENSO3.4 indices (December 1950 – February 2001). Historical monthly ENSO3.4 indices were used to extract available high-resolution monthly historical precipitation grids (1950-2001) for Mexico and constructed monthly ensembles (March 2001 – February 2011 hindcasts). Formerly, a precipitation categorization of monthly observed and simulated precipitation (2001-2011 hindcasts) was employed. Thereafter, global vector data and spatial map assessments were performed seasonally (winter, spring, summer, and fall). Global KSS and HSS metrics indicated the model approach has skill, especially in the spring and fall. Spatial metrics exposed large areas with hit rates > 0.60 in winter and spring, though in winter and spring (dry seasons), it was due to the precipitation categorization hindcast and observed were within the first classification. Lower hit rates, but still acceptable (> 0.40), were detected in summer and fall (during the rainy season and at the end, respectively) because more precipitation classifications were tested and prone to miss. Spatial Spearman correlations provided specific areas of significant model performances and found that high hit rates during the winter and spring are spurious. Meanwhile, it was also found that during the fall the model approach is reliable in most of Mexico, followed by the spring, and in constraint areas in summer and winter across the country. It also appears that dominant ENSO neutral events followed by balanced ENSO cooling and warming events do not prefer the model skill. Overall, the empirical method shows promise (low-cost human and computational resources if ENSO indices expose certainty in its Lead months to forecast) and has the potential to be used in other developing countries influenced by El Niño phenomena.

The purpose of this article is to analyze urban form through the mapping of morphological indices, namely impervious surface fraction, building density, verticality, height/width ratio, roughness length, and porosity, to support urban planning in the city of João Pessoa, PB, in northeastern Brazil. The application of this study identifies and calculates such significant indices for the city's urban space from a Geographic Information System (GIS) model. The spatial indices play notable roles in climate at different scales, developing guidelines to maximize environmental quality, promote improvements to thermal comfort, minimize the urban heat island in the city of João Pessoa, and provide relevant data (considering microclimate aspects), guiding decisions related to the planning process.

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels considering Nigeria as case study. It is found that high solar radiation in Nigeria increases surface temperature of PV panel above 25oC of optimal operating temperature of PV panels. Redundant energy gain from incident solar energy is dissipated at the rear of PV panels as heat, which reduces the efficiency of PV panel. Cooling mechanism is needed to cool the PV panels to increase the efficiency. In this study we demonstrated a unique design of a bifunctional photovoltaic-thermal (PVT) system by employing heat exchanger at the rear of PV panel and water is used as a working fluid that is circulated through the heat exchanger to remove the excess heat. It is observed from the simulation results that Maiduguri peak annual electrical power output gives 1907kWh/kWp which is the highest, because of high solar radiation average of 727W/m2 in a year. And for Makurdi the peak annual electrical power output of 1542kWh/kWp while for Port Harcourt the peak power output of 1355kWh/kWp respectively. Interestingly, Polycrystalline Si-PV surface temperature decrease from 49.25oC to 38.38oC. Electrical power increased from 1526.83W to 1566.82W in a day and efficiency increase from 13.99% to 15.01%.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

A medium scale household in South Africa consumes about 1000 kWh on average, and ae household spend about 3000 ZAR per month on energy supply using grid electricity. Grid electricity. South Africa’s energy is supplied by a huge governmental organization. Statistical analyses indicate that projected increase of the cost of grid electricity in South Africa is about 30% per annum for the next five years. Our research show that Photo-Voltaic (PV) technology can offer a viable alternative, provided a large initial capital outlay can be made. The technology is user-friendly and easy to operate. It is calculated that the cost of electricity, capitalized over 20 years, considering an 80 % supply of needs and assuming 20 sunny days per month, is about 2.80 ZAR. The study also shows that utilizing a hybrid combination of renewable energies, such as combining PV supply with solar thermal energy absorbers, and converting thermal energy to electricity, as energy supply systems, could reduce the current cost of electricity per household in South Africa to about half of national grid supply prize, R1,50 per kWhr. The study also shows that water provides as a most viable medium to store energy, instead of using expensive battery technology to perform such functions.

Increased exposure to artificial light at night can affect human health including disruption of melatonin production and circadian rhythms and extend to increased risks of hormonal cancers and other serious diseases. In addition, multiple negative impacts on fauna and flora are well documented, and it is a matter of fact that artificial light at night is a nuisance for ground-based astronomy. These impacts are frequently linked to the colour of the light or more specifically to its spectral content. Artificial light at night is often mapped by using space borne sensors, but most of them are panchromatic and thus insensitive to the colour. In this paper, we suggest a method that allows high resolution mapping of the Artificial light at night by using ground-based measurements with the LANcube system. The device separates the light detected in four bands (Red, Green, Blue, and Clear) and provides this information for six faces of a cube. We found relationships between the LANcube’s colour ratios and 1- the Melatonin Suppression Index, 2- the StarLight Index and 3- the Induced Photosynthesis Index. We show how such relationships combined with data acquisition from a LANcube positioned on the top of a car can be used to produce spectral indices maps of a whole city in a few hours.

Graph theory plays a crucial role in modeling and designing of chemical structure or chemical network. Chemical Graph theory helps to understand the molecular structure of molecular graph. The molecular graph consists of atoms as vertices and bonds as edges. Topological indices capture symmetry of molecular structures and give it a mathematical language to predict properties such as boiling points, viscosity, the radius of gyrations etc. In this article, we study the chemical graph of carbon Crystal structure of graphite and cubic carbon and compute several degree-based topological indices. Firstly we compute M-Polynomials of these structures and then from these M-polynomials we recover nine degree-based topological indices.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

With the ever-growing emphasis on global decarbonization and rapid increases in the power density of electronics equipment in recent years, new methods and lightweight materials have been developed to manage heat load as well as interfacial stresses associated with Coefficient of Thermal Expansion (CTE) mismatch between components. The Al-Si system provides an attractive combination of CTE performance and high thermal conductivity whilst being a very lightweight option. Such materials are of interest to industries where thermal management is a key design criterion, such as aerospace, automotive, consumer electronics, defense, EV and space. This paper will describe the development and manufacture of a family of high-performance hypereutectic Al-Si alloys (AyontEX™) by a powder metallurgy method. These alloys are of particular interest for structural heat sink applications that require high reliability under thermal cycling (CTE of 17μm/(m·°C)) as well as reflective optics and instrument assemblies that require good thermal and mechanical stability (CTE of 13μm/(m·°C)). Critical performance relationships are presented, coupled with the microstructure, physical and mechanical properties of these Al-Si alloys.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

The thermal insulation properties of building walls are critical to the overall energy efficiency and comfort of a building. One important factor that can affect these properties is the type of bricks used in construction. Bricks can vary in their geometry and thermal coefficient, which can impact their ability to transfer heat through the wall. The geometry of a brick can affect its thermal properties by altering the amount of air trapped within it and the surface area available for heat transfer. Hollow bricks or those with complex geometries may have lower thermal conductivity than regular solid bricks due to the air pockets trapped within them. Conversely, larger surface areas on the exterior of the brick can increase heat transfer. The thermal coefficient of clay, a common material used in brick production, is another important factor. Clay has a relatively low thermal conductivity, meaning it is a poor conductor of heat. However, the quality of the clay, as well as the firing temperature and duration used in brick production, can impact its thermal coefficient. Higher firing temperatures and longer firing times can result in a more compact and dense clay brick, which can improve its thermal properties. In summary, the thermal insulation properties of building walls can be significantly affected by the type of bricks used in their construction. It is important to consider the geometry and thermal coefficient of the bricks when designing a building to achieve the desired level of thermal insulation. By selecting bricks with appropriate properties, designers can help to improve the energy efficiency and comfort of the building while reducing its environmental impact.

The optimal combination of five components to develop a concrete for high-temperature applications was studied through a response surface methodology known as mixture design of experiment. The selected components were water, an alkali-activated binder based on ferronickel slag activated with potassium silicate and potassium hydroxide, and three aggregate sizes corresponding to 0-4 mm, 4-8 mm, and 8-16 mm. Selected response parameters were slump and compressive strength before and after heat exposure. Six cubes of side 150 mm were cast for each concrete mix, three for ambient and three for residual (post-heat exposure) compressive strength. All 20 concrete mixes were exposed to a thermal load of 600 °C for two hours. The optimal concrete mix was adapted for large-scale applications, by increasing slump and replacing limestone with olivine aggregates for enhanced residual compressive strength. The adapted mix resulted in concrete with 76 MPa and 32 MPa compressive strength before and after high-temperature exposure. The CO2 emissions were found to be 77 % lower when compared to traditional OPC concrete.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

In this paper, we demonstrate a method of measuring the flexural elastic modulus of ceramics at an intermediate (~millimeter) scale, at high temperatures. We used a picosecond laser to precisely cut micro-beams from the location of interest in a bulk ceramic. They had a cross-section of approximately 100 μm × 300 μm, and a length of ~1 cm. They were then tested in a thermal-mechanical analyzer at room temperature, 500°C, 800°C, and 1100°C using the four-point flexural testing method. We compared the elastic moduli of high-purity Al2O3 and AlN measured by our method with the reported values in the literature and found that the difference was less than 5% for both materials. This paper provides a new and accurate method of characterizing the high-temperature elastic modulus of miniature samples extracted from representative/selected areas of bulk materials.

We characterize the form of the order divisor graph of cyclic groups based on the group order. Furthermore, we describe some topological indices of the order divisor graph of cyclic groups, including the Wiener index, Harary index, first Zagreb index, and second Zagreb index.

Haemodynamic indices are widely used in clinical practice for deciding on a particular type of treatment. Low quality of the CT data and tachycardia complicate interpretation of the measured or simulated values. In this work, we present a novel approach for evaluating resistances in terminal coronary arteries. Using 14 measurements from 10 patients, we show that this algorithm retains the accuracy of 1D haemodynamic simulations in less detailed (truncated) geometric models of coronary networks. We also apply the variable systole fraction model to study the effect of elevated heart rate on the values of FFR, CFR and iFR. We conclude that tachycardia may produce both overestimation or underestimation of coronary stenosis significance.

Traditional phase change composites usually suffer poor mechanical property and easy collapsing in the phase changing process. Herein, a highly flexible phase change composite is fabricated using thermoplastic elastomer as the basic gel and the expanded graphite/paraffin as the filler. This new phase change composite shows a tensile strength of 2.1 MPa and a breaking elongation of 220%. It has a melting enthalpy of 145.4 J•g^-1 and a thermal conductivity of 2.2 W•m^-1•K^-1 with 70% of expanded graphite/paraffin. The thermoplastic elastomer based phase change composite exhibits great reversible property after 200 heating/cooling cycles. This flexible phase change composite demonstrates good photo-thermal energy charging/discharging property and shows great potential to be applied in the solar thermal energy systems.

Thermal infrared imagery provides temperature information on target objects, and has been widely applied in non-destructive testing. However, thermal infrared imagery is not always able to display detailed textures of inspected objects, which hampers the understanding of geometric entities consisting of temperature information. Although some commercial software has been developed for 3D thermal model displays, the software requires the use of expensive specific thermal infrared sensors. This study proposes a cost-effective method for 3D thermal model reconstruction based on image-based modeling. Two smart phones and a low-cost thermal infrared camera are employed to acquire visible images and thermal images, respectively, that are fused for 3D thermal model reconstruction. The experiment results demonstrate that the proposed method is able to effectively reconstruct a 3D thermal model which extremely approximates its corresponding entity. The total computation time for the 3D thermal model reconstruction is intensive while generating dense points required for the creation of a geometric entity. Future work will improve the efficiency of the proposed method in order to expand its potential applications to in-time monitoring.

Amphiphilic block copolymers of N-vinyl pyrrolidone (NVP) and various vinyl esters (VEs), PNVP-b-PVEs, namely vinyl butyrate (VBu), vinyl decanoate (VDc) and vinyl stearate (VSt) were synthesized by RAFT polymerization techniques. The sequential addition of monomers methodology was employed starting from the polymerization of NVP followed by the polymerization of the VEs monomer. The reaction was conducted at 80oC in dioxane solutions using AIBN as initiator and O-ethyl S-(phthalimidylmethyl) xanthate as the CTA. The block copolymers were characterized by Size Exclusion Chromatography (SEC) and NMR spectroscopy. The thermal transitions of the copolymers were studied by Differential Scanning Calorimetry (DSC), whereas their thermal stability via Thermogravimetric Analysis (TGA) and Differential Thermogravimetry (DTG).

. (1) Background: The aim of this study was to verify the differences in body composition, power and lower limb muscle strength in futsal players from three competitive levels. (2) Methods: The study involved 68 players (24.26 ± 4.63 years), divided into three competitive levels: elite, sub-elite and amateur. To assess physical condition, we used the Inbody270, the ChronoJump and the Isokinetic Dynamometer and used the non-parametric Kruskal-Wallis test to compare the three independent variables. (3) Results: There were no differences in body composition between the players at the three competitive levels. With regard to lower limb muscle power and strength, the elite group showed, on average, better performance and capabilities, especially when compared to the amateur group, and all groups showed an H/Q ratio > 60%. (4) Conclusions: We conclude that there are not many differences in physical condition between the three competitive levels of futsal, despite the unequal sporting demands between them. However, the elite group has greater power and muscle strength, and both groups showed a high probability of lower limb muscle injury at this stage of the sporting season, alerting sports training professionals to the importance of individualized analysis of physical condition and performance capacity.

In this study, we performed periodicity analyzes of selected daily solar (FI, CI), geomagnetic (Ap, Dst, Scalar B) and cosmic (CRI) activity indices for the last solar Cycle 24 (December 2008 to December 2019). To investigate the periodic variations of above selected data sets the Multi Taper Method (MTM), Morlet wavelet, Cross Wavelet Transform (XWT), and Wavelet Coherence (WTC) analysis techniques were used. In results of our analysis we found that i) the 25-33 and 2048-day periodicities exist in all data sets without any exception, while all other detected periodicities have data preferences, ii) all detected periods located around the maximum phase of the cycle (Cycle 24), iii) the phase relations between compared data sets periodicities are gradually changing from small periods to large ones; there are no phase relations between small periodicities and they show mixed phases, while they are completely in phase/antiphase for large periodicities, iv) all detected FI periodicities, except 2048 days periodicity, are common periodicities with all other data sets used in this study.

The urban environment induces stress on trees and the impact can be identified by observing the condition of the crown. The aim of this study is to correlate the variables crown density (Cdn), crown transparency (Ctr) and dieback (Cdie) with the following vegetation indices: normalized difference vegetation index (NDVI), enhanced vegetation index (EVI2), blue normalized difference vegetation index (BNDVI), green normalized difference vegetation index (GNDVI), green-red vegetation Index (GRVI) and red-green-blue vegetation index (RGBVI) of the tree crown located in urban green areas, as well as chlorophyll fluorescence (Fv/Fm) as an indirect indicator of tree health condition. A total of 549 trees were evaluated, represented in 24 families, 36 genera and 53 species; the variables had average values of 67.96 % in Cdn, 35.19 % in Ctr and 1 % in Cdie. Correlations were found between Fv/Fm, NDVI and BNDVI. NDVI and BNDVI correlated with variables such as Cdn and Ctr, mainly in species such as Ligustrum lucidum, Jacaranda mimosifolia and Fraxinus uhdei. Therefore, it is possible to evaluate tree health condition of trees in urban green environments through the identification of unfavorable conditions at the crown level by using vegetation indices for some of the species studied.

Air pollution is responsible for any adverse effects on human beings. Thermal discomfort, on the other hand, is able to overload the human body and eventually provoke health implications due to the heat imbalance. Methods: The aim of the present work is to study the behavior of two bio-climatic indexes and statistical characteristics of the air quality index for Sofia city - the capital of Bulgaria for the period 2008 - 2014. The study is based on WRF-CMAQ model system simula-tions with a spatial resolution of 1 kilometer. The air quality is estimated by the air quality index, taking into account the influence of different pollutants and the thermal conditions by two indi-ces, respectively, for hot and cold weather. Results: It was found that half of the heat and cold index categories are present in the simulations. Their distribution has some spatial features. All air quality categories are present in the domain, with dominance only of the O3 and PM10. Conclu-sions: It was found that Sofia is not so hot and air polluted place, but in some situations, people have to have some concerns when intend to be outdoors for a prolonged time.

The use of heart rate variability (HRV) in research has been greatly popularized over the past decades due to the ease and affordability of HRV collection, coupled with its clinical relevance and significant relationships with psychophysiological constructs and psychopathological disorders. Despite the wide use of electrocardiogram (ECG) in research and advancement in sensors technology, the analytical approach and steps applied to obtain HRV measures can be seen as complex. Thus, posing a challenge to users who may not have the adequate background knowledge to obtain the HRV indices reliably. To maximize the impact of HRV-related research and its reproducibility, parallel advances in users’ understanding of the indices and the standardization of analysis pipelines in its utility will be crucial. This paper addresses this gap and aims to provide an overview of the most up-to-date and commonly used HRV indices, as well as common research areas that these indices have shown to be very useful, particularly in psychology. In addition, we also provide a step-by-step guide on how to perform HRV analysis using an integrative neurophysiological toolkit, NeuroKit2.

Conversion of electromagnetic energy into magnetohydrodynamic energy occurs when the electric conductivity changes from negligible to finite values. This process is relevant during the epoch of reheating of the early Universe at the end of inflation and before the emergence of the radiation-dominated era. We find that conversion into kinetic and thermal energies is primarily the result of electric energy dissipation and that the magnetic energy plays only a secondary role in this process. This means that, since electric energy dominates over magnetic energy during inflation and reheating, significant amounts of electric energy can be converted into magnetohydrodynamic energy when conductivity emerges early enough, before the relevant length scales become stable.

In this paper we establish information theoretical bridges between 1) Thermal Heisenberg uncertainties $\Delta x \Delta p$ (at temperature $T$), and 2) LMC structural quantifiers. After having achieved such purpose, we determine to what an extent our bridges can be extended to both the semi classical and classical realms. Also, we find a strict bound relating a special LMC structural quantifier to quantum uncertainties.

This study addresses the gap in methodological guidelines for Neuroergonomic attention assessment in safety-critical tasks, focusing on validating EEG indices including the Engagement Index (EI) and Beta/Alpha ratio alongside subjective ratings. A novel task-embedded reaction time paradigm was developed to evaluate the sensitivity of these metrics to dynamic attentional demands in a more naturalistic multitasking context. By manipulating attention levels through varying secondary tasks in the NASA MATB-II task while maintaining a consistent primary reaction-time task, the study successfully demonstrated the effectiveness of the paradigm. Results indicate that both Beta/Alpha ratio and EI are sensitive to changes in attentional demands, with Beta/Alpha being more responsive to dynamic variations in attention, and EI reflecting more the overall effort required to sustain performance, especially in conditions where maintaining attention is challenging. The potential for predicting the attention lapses through integration of performance metrics, EEG measures, and subjective assessments was demonstrated, providing a more nuanced understanding of dynamic fluctuations of attention in multitasking scenarios, mimicking those in real-world safety-critical tasks. These findings provide a foundation for advancing methods to accurately monitor attention fluctuations and mitigate risks in critical scenarios, such as train-driving or automated vehicle operation, where maintaining high attention level is crucial.

In this paper, we synthesized MC(BeA-co-MMA) copolymer microcapsules through suspension polymerization. The pendent n-behenyl group of BeA is highly crystalline, and it acts as the side-chain in the structure of BeA-co-MMA copolymer. The highly crystalline n-behenyl side-chain provides BeA-co-MMA copolymer thermal-energy-storage capacity. In order to investigate the correlation between thermal properties and crystal structure of BeA-co-MMA copolymer, the effects of monomer ratio, temperature changing and changing rate, as well as synthesis method were discussed. The monomer ratio influenced crystal transition behavior and thermal properties greatly. The DSC results proved that when the monomer ratio of BeA and MMA was 3:1, MC(BeA-co-MMA)3 showed the highest average phase change enthalpy ΔH (105.1 J·g–1). It indicated that the n-behenyl side-chain formed relatively perfect crystal region, which ensured a high energy storage capacity of copolymer. All the DSC and SAXS results proved that the amount of BeA had a strong effect on the thermal-energy-storage capacity of copolymer and the long spacing of crystals, but barely on the crystal lamella. It was found that MMA units worked like defects in the n-behenyl side-chain crystal structure of BeA-co-MMA copolymer. Therefore, a lower fraction of MMA, that is, a higher fraction of BeA contributed to a higher crystallinity of BeA-co-MMA copolymer for providing a better energy storage capacity and thermoregulation property. ST(BeA-co-MMA) copolymer sheets with the same ingredients as microcapsules were also prepared through light-induced polymerization aiming at clarifying the effect of synthesis method. The results proved that synthesis method mainly influenced the copolymer chemical component, but lightly on the crystal packing of n-behenyl side-chain.

In the quest for more efficient solar thermal systems, accurately determining the thermal emittance of low-emissive materials is crucial in determining the power losses. This paper describes the calorimetric method designed to precisely measure the thermal emittance of Selective Solar Absorbers (SSAs) to be used in High Vacuum Flat Plate Collectors (HVFPCs). The method's capability is demonstrated through the successful correction of thermal emittance values for copper samples of varying sizes, including dimensions down to 49 cm². Results highlight the method's potential to significantly reduce measurement errors associated with small-size and/or low-emittance samples, providing a path forward to improve the design and efficiency of SSAs. This research marks a significant step in advancing solar thermal technology by enabling emittance measurements with a precision better than 0.003, which is essential for the development of high-performance solar thermal absorbers. The method has also been applied to correct the thermal emittance value of SSA measured in previous measurement campaigns, and it allows a better estimation of the SSA efficiency conversion curve.

The current echocardiography reference values are derived primarily from populations in North America and Europe. It becomes necessary to study ethnically different groups of the population, which often have different living conditions, food habits and lifestyle. The aim of the study was to compare echocardiography indicators in urbanized patients with arterial hypertension of the Shor and non-indigenous ethnic groups living in the Gornaya Shoria region. The study included patients with arterial hypertension: 58 Shors (20 men and 38 women) and 50 non-indigenous residents (15 men and 35 women) of Gornaya Shoria. All underwent an echocardiographic study with an assessment of the left heart parameters. We assessed the left ventricular hypertrophy (LVH) severity, LV geometry and diastolic function in the ethnic and sex groups. Shor with hypertension no showed a significant difference in left ventricular dimensions compared to Caucasian. Severe abnormal LVH was associated in the Shors with glucose levels (OR 3.24, 95%CI 1.56-6.7, p=0,001), and in Caucasians with systolic (p=0.021) and diastolic (p=0.011) blood pressure, and heart rate (p=0.033). The Shor men were more likely to have normal LV diastolic function (p=0.029) and LV concentric remodeling (p=0.023), and less often to have normal LV geometry (p=0.015) compared to non-indigenous men. Thus, this study can be useful in assessing the impact of the development of arterial hypertension, as well as the impact of changing the lifestyle of the Shors when moving to the city from rural areas on ethnic differences in echocardiography.

We assessed how close human perceptions of landscape modification matched a multivariate index based on remotely sensed data of the same locations. Using a Human Footprint (HF) map of the continental U.S. (scaled 0-100), we created three series of aerial images, each with ten images distributed evenly across the 10 deciles of HF score. Using a web-based survey, 290 members of the global public ranked the images in one series based on their perception of the degree of human modification. Respondents also reported age, sex, and country. The degree of correspondence between rankings by respondents and by HF score was high, an average of 1.29 units of difference out of a maximum possible of 5.0. Differences among respondents were not explained by age, sex, or general geographic location. These results suggest that human perception of relative landscape modification conforms closely with the relative ranking made by a multivariate, analytical index.

Increasing demand for electricity and modernization of power systems within competitive markets induce power systems to operate close to their stability limits. Therefore, a power system continuous monitoring and control by using voltage stability indices are known exigence. This is the first-ever effort, examined more than 40 voltage stability indices thorough an exhaustive study based in on their formulation, application, performance, and assessment measures. Which is conducted based on a logical and chronological order considering the most recent worldwide applied voltage stability indices. However, the generalizability of such an immense diversity of these indices in term of multivariable objectives subjects to a certain limitation to summate into a deciphered outcome. Despite all these obstacles, this study systematically reviews available indices in the literature within the past three decades to set out an integrated knowledge with an insight up-to-date exposition. That followed with a comparative analysis in term of their similarity, functionality, applicability, formulation, merit, demerit, and overall performances. Also, a broad categorization of voltage stability indices is addressed. This study with an immediate implication in practice as an exhaustive roadmap can be counted a planning and operation reference in the context of voltage stability for students, researchers, scholars, and practitioners.

Topological indices are numerical parameters of a graph which characterize its topology and are usually graph invariant. In this paper, bounds for the Randić, general Randić, sum-connectivity, the general sum-connectivity and harmonic indices for tensor product of graphs are determined by using the combinatorial inequalities and combinatorial computing.

Comprehensive understanding of tree characteristics and conditions holds paramount importance for the precise management of hazelnut orchards. It facilitates the determination of tree vigor, pruning requirements, phytosanitary interventions, and plant water consumption. The primary objective of this study was to explore, for the first time on a fruit tree with a bushy structure and across trees of four Italian distinct hazelnut cultivars, the efficacy of multispectral and thermal UAV (Unmanned Aerial Vehicle) technologies in assessing canopy attributes, vegetative growth, and predicting abiotic stresses. These technologies serve as tools for precision agriculture, enabling the computation of various indices such as the Normalized Difference Vegetation Index (NDVI) and crop water stress index (CWSI). The study of water content is of particular importance at this time, especially considering the increasing water stress levels in Europe as well as globally. While Red Green Blue (RGB) and thermal imagery collectively demonstrated superior performance in model reconstruction, the multispectral UAV remained more adept at characterizing size traits of hazelnut plants. Thermal images alone proved inadequate for accurately reconstructing hazelnut biometric characteristics. Furthermore, all indices were found to be cultivar-specific, underscoring the importance of conducting studies across different cultivars. The utilization of two UAVs, namely multispectral and thermal, facilitated the examination of the relationship between NDVI and CWSI across tree species.

Achieving the thermal conductivity required for efficient heat management in semiconductors and other devices requires the integration of thermally conductive ceramic fillers at concentrations of 60 vol% or higher. However, the increased filler content often negatively affects the mechanical properties of the composite matrix, limiting its practical applicability. To address this issue, in this paper, we present a new strategy to reduce the required ceramic filler content: the use of a thermally conductive ceramic composite filler with carbon nanotubes (CNT) grown on aluminum nitride (AlN). We have combined catalyst coating technology with vacuum filtration to ensure that the catalyst is uniformly applied to micrometer-sized AlN particles, followed by efficient and uniform synthesis of CNTs using a water-assisted process in a vertical furnace. By carefully controlling the number of vacuum filtration cycles and the growth time of the CNTs, we demonstrate precise control over the number and length of the CNT layers, thereby adjusting the properties of the composite to the intended specifications. When AlN/CNT hybrid fillers are incorporated into silicone rubber, while maintaining the mechanical properties of rubber, the thermal diffusivity achieved at reduced filler levels exceeds that of composites using AlN-only or simultaneous AlN and CNTs formulations. This demonstrates the critical role of CNTs on AlN surfaces. Our study represents a significant advancement in the design of thermally conductive materials with potential implications for a wide range of applications.

Collatz conjecture states that an integer $n$ reduces to $1$ when certain simple operations are applied to it. Mathematically, the Collatz function is written as $f^k(n) = \frac{3^kn + C}{2^{z}}$, where $z, k, C \geq 1$. Suppose the integer $n$ violates Collatz conjecture by reappearing as $2^in$, where $i \geq 1$, then the equation modifies to $n \left(1 - \frac{3^k}{2^{z}2^i}\right) = \frac{C}{2^{z}2^i}$. The article takes an elementary approach to this problem by calculating the bounds on the values of $\frac{C}{2^{z}2^i}$ and $1 - \frac{3^k}{2^{z}2^i}$. Correspondingly, an upper limit on the integer $n$ is placed that can re-appear in the sequence. The integer $n$ lies in the $(-\infty, 5)$ range, and the limit on the number of odd steps is $k < 3$. Finally, it is shown that no integer chain exists that does not lead to 1.

The importance of small urban green areas has increased in the context of rapid urbanization and densification of the urban tissue. The analysis of these areas through remote sensing has been limited due to the low spatial resolution of freely available satellite images. We propose a timeseries analysis on 3 m resolution Planet images, using GEOBIA and vegetation indices, with the aim of extracting and assessing the quality of small urban green areas in two different climatic and biogeographical regions – temperate (Bucharest, Romania) and mediterranean (Athens, Greece). Our results have shown high accuracy (over 91%) regarding the extraction of small urban green areas in both cities, across all analysed images. The timeseries analysis showed consistency in location for around 55% of the identified surfaces throughout the entire period. The vegetation indices registered higher values in the temperate region, due to the vegetation characteristics and the planning of the two cities. For the same reasons, the increase in vegetation density and quality, as a result of the distance from the city centre and the decrease in the density of built-up areas is more obvious in Athens. The proposed method provides valuable insights in the distribution and quality of small urban green areas at city level and can represent the ground basis for many analyses, currently limited by poor spatial resolution.

Polycystic ovary syndrome (PCOS) is a complex hormonal disorder which impair ovarian function. The adherence to healthy dietary patterns and physical exercise are the first line of recommended treatment for PCOS patients, but it is no clear what type of diet is more adequate. In this case-control study, we explore the association between the adherence to five dietary quality indices widely used and PCOS. We enrolled 126 cases of PCOS and 159 controls (Murcia, Spain). Diagnostic of PCOS and its phenotypes were established following the Rotterdam criteria [hyperandrogenism (H), oligoanovulation (O), polycystic ovaries morphology (POM)]. We used a validated food frequency questionnaires to calculate the scores for five dietary indices: alternate Healthy Eating index (AHEI), AHEI-2010, relative Mediterranean Dietary Score (rMED), alternate Mediterranean Dietary Score (aMED) and Dietary Approaches to Stop Hypertension (DASH). We used multivariable logistic regression to estimate adjusted odds ratios and confidence intervals. In the multivariable analysis, AHEI-2010 index was inversely associated with “H+O” PCOS’ phenotype (ORQ3 VS Q1= 0.1; 95% CI :(0.0; 0.9); P for trend= 0.02). In conclusion, we did not find any statistical significative association between dietary indices and total, anovulatory and ovulatory PCOS, but it seems interesting explore these association among the diverse phenotypes of PCOS in studies with higher sample size.

Sufficient evidence is currently available to demonstrate the reality of the warming of our planet's climate system. Global warming has different effects on climate at the regional and local levels. The detection of changes in extreme events using instrumental data provides further evidence of such warming and allows for the characterization of its local manifestations. The present study analyzes changes in temperature and precipitation extremes in the Mexican state of Zacatecas using climate change indices developed by the Expert Team on Climate Change Detection, Monitoring and Indices (ETCCDI). We studied a 40-year period (1976-2015) using annual and seasonal time scales. Maximum and minimum temperature data were used, as well as precipitation statistics from the Mexican climatology database (CLICOM) provided by the Mexican meteorological service. Weather stations with at least 80% of data availability for the selected study period were selected; these databases were subjected to quality control, homogenization, and data filling using Climatol, which runs in the R programming language. These homogenized series were used to obtain daily grides of the three variables at a resolution of 1.3 km. Results reveal important changes in temperature-related indices, such as the increase in maximum temperature and the decrease in minimum temperature. Irregular variability was observed in the case of precipitation, which could be associated with low-frequency oscillations such as the Pacific Decadal Oscillation and the El Niño–Southern Oscillation. The possible impact of these changes in temperature and the increased irregularity of precipitation could have a negative impact on the agricultural sector, especially given that the state of Zacatecas is the largest national bean producer. The most important problems in the short term will be related to the difficulty of adapting to these rapid changes and the new climate scenario, which will pose new challenges in the future.

Considering animal welfare, the free-range laying hen farming model is increasingly gaining attention. However, in some countries, large-scale farming still relies on the cage-rearing model, making the focus on the welfare of caged laying hens equally important. To evaluate the health status of caged laying hens, a dataset comprising visible light and thermal infrared images was established for analyses, including morphological, thermographic, comb, and behavioural as-sessments, enabling a comprehensive evaluation of the hens' health, behaviour, and population counts. To address the issue of insufficient data samples in the health detection process for indi-vidual and group hens, a dataset named BClayinghens was constructed containing 61,133 images of visible light and thermal infrared images. The BClayinghens dataset was completed using three types of devices: smartphones, visible light cameras, and infrared thermal cameras. All thermal infrared images correspond to visible light images and have achieved positional alignment through coordinate correction. Additionally, the visible light images were annotated with chicken head labels, obtaining 63,693 chicken head labels, which can be directly used for training deep learning models for chicken head object detection and combined with corresponding thermal infrared data to analyze the temperature of the chicken heads. To enable the constructed deep-learning object detection and recognition models to adapt to different breeding environ-ments, various data enhancement methods such as rotation, shearing, colour enhancement, and noise addition were used for image processing. The BClayinghens dataset is important for ap-plying visible light images and corresponding thermal infrared images in the health detection, behavioural analysis, and counting of caged laying hens under large-scale farming.