Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

The design complexity of the new generation of civil aero-engines results in higher demands on engines’ components, higher component temperature, higher heat generation, and, finally, critical thermal management issues. This paper will propose a methodological approach to create physics-based models for heat loads developed by sources as well as a systematic sensitivity analysis to identify the effects of design parameters on the thermal behaviour of civil aero-engines. The ranges and levels of heat loads generated by heat sources (e.g., accessory gearbox, bearing, pumps, etc.) and heat absorption capacity of heat sinks (e.g., engine fuel, oil, and air) are discussed systematically. The practical research challenges for thermal management system design and development for the new and next generation of turbofan engines will then be addressed through a sensitivity analysis of the heat load values as well as the heat sinks flow rates. The potential solutions for thermal performance enhancements of propulsion systems will be proposed and discussed accordingly.

: Tunnel instability and lining integrity are intimately tied to the creep properties of the surrounding rock. The acquisition of rock mass creep parameters is critical in ascertaining the appropriate timing for lining construction. Nevertheless, creep tests on rock specimens conducted in a controlled setting cannot be straightforwardly extrapolated to rock mass creep analysis. This study performs laboratory-based creep tests on mudstone samples and establishes the corresponding creep constitutive model. Integration of a Mohr-Coulomb element with the Burgers model in series serves to characterise the yield creep behaviour of the rock mass. Additionally, the research outlines a series of 100 orthogonal experiments utilising randomised creep parameters, and formulates a GA-BP neural network inversion model. Employing long-term deformation measurements from the crown and sidewalls of the project site, this study deduces the creep parameters of the mudstone in the investigated tunnel section and examines the prolonged deformation traits of the surrounding rock. Drawing on the deformation traits of the surrounding rock and the forces impacting the primary support and lining structures, this paper evaluates the earliest and latest viable lining casting periods and pinpoints an optimal timing interval for lining implementation. The methodologies employed herein can serve as a benchmark for analogous endeavors internationally.

Plant growth regulators (PGRs) and deficit irrigation (DI) play a crucial strategic role in sustaining agricultural yield and reducing water stress in drought prone areas. The study was carried out in 2021-2022 to assess the impact of various PGRs (SA & NAA) & irrigation levels (60% Epan, 80 % Epan, and 100 % Epan) with DI & partial root drying (PRD) irrigation strategies. PGR application boosted fruit yields and demonstrated its significance in reducing water stress by lowering canopy temperature, maintaining higher relative water content in the leaves, modifying stomatal opening, and increasing photosynthetic rate. PGRs were used to assess the increased accumulation of total phenols, flavonoids, and improved antioxidant activity. Results indicated that exogenous use of PGRs like SA+NAA in conjunction with 80% irrigation levels increased fruit yield (31.97 and 40.38%) and water productivity (64.92 and 75.39%) for DI and PRD treatments, respectively. Thus standardizing irrigation and crop management practices including PGR application can be recommended to boost pomegranate productivity particularly in water-scarce environments.

Coal gasification with carbon dioxide is a process for generating clean gaseous fuels and relieving greenhouse effect. Zhundong coal has high alkali and alkali earth metals (AAEMs) content, medium volatile and low ash in nature. Isothermal CO₂ gasification of char derived from Zhundong coal (R-char) and char from acid washing R-char (AR-char) are performed in thermo-gravimetric analyzer (TGA). The effect of AAEMs is investigated on the gasification behavior in the range of temperatures 1073 K to 1273 K. The carbon conversion increases rapidly with increasing reaction temperature and CO₂ concentration. R-char has high gasification rate and carbon conversion compared with AR-char. The accuracy of the free-model approach for calculating activation energy at different conversions is validated by compared with different kinetic models (volume reaction model, distributed activation energy model). Moreover, R-char gasification with CO₂ shows a compensation effect as the Arrhenius parameters (EA and k0) increase or decrease simultaneously.

Phosphite (Phi) has gained attention in agriculture due to its biostimulant effect on crops. This molecule has been found to benefit plant performance by providing protection against pathogens, improving yield and fruit quality, and improving nutrient and water use efficiency. It is still unclear how Phi enhances plant growth and protects against multiple stresses. It has been hypothesized that Phi acts by directly affecting the pathogens and interacting with the plant cellular components and molecular machinery to elicit defense responses. This study delves into elucidating the mechanisms underlying Phi’s beneficial effects on plants, revealing a complex interplay with fundamental signaling pathways. A RNA-seq study of Arabidopsis seedlings under optimal and limiting phosphate conditions helped us unveil Phi’s role in promoting plant growth by activating the expression of genes involved in the biosynthesis and signaling pathways associated with abscisic acid (ABA), salicylic acid (SA), and jasmonic acid (JA). Expression of ABA-related genes, known for their involvement in stress response and development regulation, is triggered by Phi treatment, contributing to enhanced resilience and growth. Simultaneously, the activation of the SA pathway, associated with defense responses, suggests Phi’s potential in bolstering plant immunity. Moreover, Phi influences JA biosynthesis and signaling, which are crucial for defense against herbivores and pathogens, thereby strengthening plants’ defenses. Our findings reveal a multifaceted mechanism through which Phi benefits Arabidopsis development. Understanding its intricate interplay with key signaling pathways opens avenues for leveraging Phi as a strategic tool to enhance plant resilience, immunity, and growth in agricultural and ecological contexts.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Large-scale hydrological modeling in China is challenging given the sparse meteorological stations and large uncertainties associated with atmospheric forcing data.Here we introduce the development and use of the China Meteorological Assimilation Driving Datasets for the SWAT model (CMADS) in the Heihe River Basin(HRB) for improving hydrologic modeling, by leveraging the datasets from the China Meteorological Administration Land Data Assimilation System (CLDAS)(including climate data from nearly 40000 area encryption stations, 2700 national automatic weather stations, FengYun (FY) 2 satellite and radar stations). CMADS uses the Space Time Multiscale Analysis System (STMAS) to fuse data based on ECWMF ambient field and ensure data accuracy. In addition, compared with CLDAS, CMADS includes relative humidity and climate data of varied resolutions to drive hydrological models such as the Soil and Water Assessment Tool (SWAT) model. Here, we compared climate data from CMADS, Climate Forecast System Reanalysis (CFSR) and traditional weather station (TWS) climate forcing data and evaluatedtheir applicability for driving large scale hydrologic modeling with SWAT. In general, CMADS has higher accuracy than CFRS when evaluated against observations at TWS; CMADS also provides spatially continuous climate field to drive distributed hydrologic models, which is an important advantage over TWS climate data, particular in regions with sparse weather stations. Therefore, SWAT model simulations driven with CMADS and TWS achieved similar performances in terms of monthly and daily stream flow simulations, and both of them outperformed CFRS. For example, for the three hydrological stations (Ying Luoxia, Qilian Mountain, and ZhaMasheke) in the HRB at the monthly and daily Nash-Sutcliffe efficiency ranges of 0.75-0.95 and 0.58-0.78, respectively, which are much higher than corresponding efficiency statistics achieved with CFSR (monthly: 0.32-0.49 and daily: 0.26 – 0.45). The CMADS dataset is available free of charge and is expected to a valuable addition to the existing climate reanalysis datasets for deriving distributed hydrologic modeling in China and other countries in East Asia.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

To enhance pomegranate production on marginal gravelly lands, our study evaluated standardized planting techniques in an 8-year-old orchard. We employed trenching, wider pit excavation, pit digging, and auger digs with dimensions of 1 and 2 meters. Utilizing native soil from barren land, with or without spent wash, and mixing it with black soil up to 1 meter deep, we assessed growth parameters, leaf nutrients, and fruit yield. The trench and wider pit methods outperformed others, yielding greater above-ground biomass (>7.03 t tree-1), root biomass (2.5 t tree-1), and cross-sectional area (3.3 m² tree-1). Additionally, trench planting enhanced leaf phosphorus (0.28%) and potassium (1.8%) levels, fruit juice content (48.5%), total soluble solids (16.05°), and fruit yield (>9.3 t ha-1). The trench method also fostered longer roots at 90–150 cm radial distance and deeper roots at 40–60 cm depth. In summary, the trench and wider pit methods, combined with a soil mixture, are recommended for sustainable, high-quality fruit production in shallow gravelly terrains, thereby improving food security and the livelihoods of farmers in arid regions.

Ectopic expression of the MYB transcription factor of AmROSEA1 from Antirrhinum majus has been reported to change anthocyanin and other metabolites in several species. In this study, we found that overexpression of AmRosea1 significantly improved the tolerance of transgenic rice to drought and salinity stress. Transcriptome analysis revealed that a considerable amount of stress-related genes were affected by exogenous AmRosea1 during both drought and salinity stress treatments. These affected genes are involved in stress signal transduction, the hormone signal pathway, ion homeostasis and the enzymes that remove peroxides. This work suggests that the AmRosea1 gene is a potential candidate for genetic engineering of crops.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

Combining modern thermodynamics theory branches, including finite time thermodynamics or entropy generation minimization, constructal theory and entransy theory, with metallurgical process engineering, this paper provides a new exploration on generalized thermodynamic optimization theory for iron and steel production processes. The theoretical core is to thermodynamically optimize performances of elemental packages, working procedure modules, functional subsystems, and whole process of iron and steel production processes with real finite-resource and/or finite-size constraints with various irreversibilities toward saving energy, decreasing consumption, reducing emission and increasing yield, and to achieve the comprehensive coordination among the material flow, energy flow and environment of the hierarchical process systems. A series of application cases of the theory are reviewed. It can provide a new angle of view for the iron and steel production processes from thermodynamics, and can also provide some guidelines for other process industries.

An electrothermal analysis for barium titanate based ceramics is presented combining the Heywang–Jonker model for the electric resistivity with a heat dissipation mechanism based on natural convection and radiation in a one dimensional model on the device level with voltage as the control parameter. Both PTC and NTC effects are accounted for through the double Schottky barriers at the grain boundaries of the material. The problem formulated in this way admits uniform and non–uniform multiple steady state solutions that do not depend on the external circuit. The numerical bifurcation analysis reveals that the PTC effect gives rise to several multiplicites above the Curie point, whereas the NTC effect is responsible for the thermal runaway (temperature blowup). The thermal runaway phenomenon as a potential thermal shock could be among the possible reasons for the observed thermomechanical failures (delamination fracture). The theoretical results for the NTC regime and the thermal runaway are in agreement with experimental flash sintering results obtained for 3% and 8% yttria stabilized zirconia.

Replication stress (RS) is a characteristic state of cancer cells as they tend to exchange precision of replication for fast proliferation and increased genomic instability. To overcome the consequences of improper replication control malignant cells frequently inactivate parts of their DNA damage response (DDR) pathways (the ATM-CHK2-p53 pathway), while relying on other pathways which help to maintain replication fork stability (ATR-CHK1). This creates a dependency on the remaining DDR pathways, vulnerability to further destabilization of replication and synthetic lethality of DDR inhibitors with common oncogenic alterations such as mutations of TP53, RB1, ATM, amplifications of MYC, CCNE1 and others. The response to RS is normally limited by coordination of cell cycle, transcription and replication. Inhibition of WEE1 and PKMYT1 kinases, which prevent unscheduled mitosis entry, leads to fragility of under-replicated sites. Recent evi-dence also shows that inhibition of Cyclin-dependent kinases (CDKs), such as CDK4/6, CDK2, CDK8/19 and CDK12/13 can contribute to RS through disruption of DNA repair and replication control. Here, we review the main causes of RS in cancers as well as main therapeutic targets – ATR, CHK1, PARP and their inhibitors.

In this paper, the integrated performance of a modular biomass boiler with an existing industrial Rankine steam heat and power cycle and a supplementary supercritical-CO2 (sCO2) Brayton cycle is analyzed. The aim is to leverage the high efficiency supplementary sCO2 cycle to increase net generation and energy efficiency from the existing biomass boiler. Two sCO2 heater configurations situated within the flue gas flow path are investigated, namely a single convective-dominant heater, and a dual heater configuration with a radiative and a convective heater. A quasi-steady-state 1D model was developed to simulate the integrated cycle, including detailed component characteristics for the Rankine and Brayton cycles. The model solves the mass, energy, momentum, and species balance equations. The system is analyzed for three cases: (i) the existing Rankine cycle without the sCO2 integration, (ii) with the single convective-dominant sCO2 heater configuration, and (iii) the dual sCO2 heater configuration. The results show the required rate of overfiring for the sCO2 configurations, with a 15.3% increase in fuel flowrate resulting in an additional 21.2% in net power output. The model quantifies the impact of the sCO2 heaters, with reduced heat uptakes for downstream boiler heat exchangers. Furnace water wall heat uptake increased due to overfiring, offsetting the reduced heat uptakes at downstream evaporative heat exchangers. The dual configuration has more impact on Rankine cycle operation due to the radiative sCO2 heater placement in front of the second superheater, absorbing some of the direct radiation from the furnace.

Photovoltaic (PV) technologies are developing rapidly as a result of their ability to reduce energy consumption from conventional sources as well as the growth of global energy expenditures. Nevertheless, several impact categories during the PV panel life cycle occur and some principal sectors are affected. These impact categories are assessed by applying life cycle analysis (LCA) techniques through various software programs, databases and methods. Such analyses of energy technologies are crucial, as they can reveal the occurrence of hazardous emissions at distinct life cycle stages. In the present paper, a PV panel impact assessment through life cycle analysis is carried out. More precisely, a combination of PV technologies—monocrystalline, multicrystalline, copper indium gallium selenide (CIGS), amorphous, and ribbon—is studied. The impact categories of ozone depletion, human toxicity, particulate matter, ionising radiation, photochemical ozone formation, acidification, eutrophication, and ecotoxicity, as well as the sectors of human health, ecosystem quality, and environment, are assessed using the openLCA software, the ecoinvent database, the eco-indicator 99, IMPACT 2002+, ReCiPe, and TRACI methods.

This research investigated high-temperature corrosion (500 °C) of Cr-Mo steel processed using water jet peening or multifunction cavitation (MFC), and the suitability of such steel for high-temperature boilers and reaction vessels. High-temperature corrosion was induced using an embedment test and a coating test using sulfide-type K2SO4-Na2SO4 powder. To measure the relaxation of the residual stress due to the decrease in work hardening caused by an increase in specimen temperature and the difference in thermal shrinkage between the surface and interior of the specimen, a thermal cycling test was conducted. For the MFC-processed specimen, the oxide film that formed on the surface suppressed mass loss, prevented crack formation, and reduced the compressive residual stress caused by high-temperature corrosion. MFC-processed Cr-Mo steel is thus suitable for a high-temperature corrosion environment.

Transposable elements (TE) function as one of the major effectors to respond to biological or environmental stress. The mobility of TEs, which is heavily controlled under normal conditions, may be activated by stress. LncRNAs are emerging as a crucial tool in the regulation of TEs. This study focuses on the gene expression of THAP9, a domesticated transposon and lncRNA THAP9-AS1 (THAP9-antisense1), which form a sense and antisense gene pair with a promoter overlap of approximately 350bp. Under basal conditions, THAP9 is preferentially transcribed while THAP9-AS1 is heavily down-regulated. In the S-phase of the cell cycle, THAP9 expression exhibits stress-specific effects ranging from moderate enhancement to no change. On the other hand, THAP9-AS1, which has previously been reported to be upregulated in several cancers, always demonstrates enhanced expression under stress. Moreover, THAP9-AS1 is transcriptionally favoured during stress since the stress-induced fold-increase of THAP-AS1 expression is always higher than THAP9. Interestingly, the expression of both THAP9 and THAP9-AS1 exhibit a striking periodicity throughout the S-phase, reminiscent of cell cycle regulated genes. Thus, this study sets the stage to further explore the relationship between THAP9 and THAP9-AS1 and investigate THAP9-AS1’s potential regulatory role during stress.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

Thermal camouflage is a highly sought-after technology to increase the survivability of military equipment against infrared (IR) detectors. Recently, two-dimensional (2D) nanomaterials have shown low IR emissivity, widely tunable opto-electronic properties and compatibility with stealth-applications. Among them, graphene and graphene-like materials are the most attractive 2D materials used for thermal camouflage applications. In particular, in multilayer graphene (MLG) charge density can be effectively tuned through sufficiently intense electric fields or through electrolytic gating. Therefore, MLG optical properties, like infrared emissivity and absorbance, can be controlled in a wide range by voltage bias. The large emissivity modulation achievable with this material makes it suitable in the design of thermal dynamic camouflage devices. Generally, the emissivity modulation in the multilayered graphene medium is governed by an intercalation process of non-volatile ionic liquids under a voltage bias. The electrically-driven reduction of emissivity leads to a decrease in the apparent temperature of the surface, which can match that of the background enabling thermal camouflaging. Since this property is common to other graphene-based materials, here we present a review specifically focused on the recent advances in the field of the thermal camouflage properties of graphene in the form of composite film and aerogel structures. A summary of the current understanding of the working principle of thermal camouflage materials, current limitations, and future opportunities is presented and discussed.

Aquifer Thermal Energy Storage (ATES) systems are garnering attention as high-efficiency air conditioning technologies that contribute to the realization of a carbon-neutral society. This study focuses on an ATES system constructed in Japan, characterized by its complex geological conditions and thin aquifer layers. Through performance analysis using four years of operational data, we achieved a Coefficient of Performance (COP) of 5 on the building load side. This paper confirms the equivalence of the dimensionless production temperature and heat recovery rate, observing nearly identical changes in the dimensionless production temperature over four cycles (eight seasons). Furthermore, we propose an operational method for the following fiscal year that maintains the balance between accumulated storage quantity and pumping volume, based on predictions from this plant's operational pattern.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

Chitosan (CTS) is widely used in agriculture as a soil amendment, plant growth regulator and promoter of cold resistance. However, the effects of CTS on strawberry seedlings under the combined stress of high-temperature and high-light are unclear. In this study, Xuelixiang strawberry was used as a test material, and 100 mg·kg-1 CTS solution was sprayed onto the leaves. We measured the chlorophyll content, membrane peroxidation, reactive oxygen species content, antioxidant enzyme content, AsA-GSH cycle activity and other related indicators of strawberry seedling leaves under the combined stress of high-temperature and high-light and found that CTS can increase the contents of antioxidants, increase the contents of osmotic adjustment substances, increase the activity of antioxidant enzymes activity,; remove reactive oxygen species over time, reduce the damage of reactive oxygen species to photosynthetic organs and cell membranes, and improve the photosynthesis efficiency of leaves of strawberry plants under high-temperature and high-light stress, thereby reducing damage to strawberry seedlings caused by high-temperature and high-light.

An increasing ecological phase-shift from coral dominated reefs to macroalgae dominated reefs as a result of anthropogenic impacts, such as eutrophication, sedimentation, and overfishing, has been observed in many reef systems around the world. Ocean warming is a universal threat to both corals and macroalgae, which may alter the outcome of competition between them. Therefore, in order to explore the effects of indirect and direct exposure to macroalgae on the physiological, biochemical, and genetic expression of corals at elevated temperature, the coral Acroproa hyacinthus and highly invasive green algae Caulerpa taxifolia have been chosen. Physiologically, the results exhibited that distinguish from control and direct contact treatments, the density and chlorophyll a content of zooxanthella decreased by 53.1% and 71.2% respectively, when coral indirect contacted with algae at ambient temperature (27°C). Besides, enzyme activities of superoxide dismutase (SOD) and catalase (CAT) in coral tissue were enhanced by interacting with algae. After an increase of 3°C, the density and chlorophyll a content of zooxanthella reduced by 84.4% and 93.8% respectively, whereas the enzmy activities of SOD and CAT increased by 2.3 and 3.1-fold. However, only the zooxanthellae density and pigment content decreased when C.taxifolia co-culture with A.hyacinthus at 30°C. Molecularly, different from the control group, the differentially expressed genes (DEGs) such as Rab family, ATG family and Casp7 were significantly enriched in endocytosis, autophagy and apoptosis pathways , regardless whether A.hyacinthus was indirect or indirect exposure to C.taxifolia at 27°C. Under thermal stress without algae interaction, the DEGs were significantly enriched in microbial immune signal transduction pathways, such as Toll-like receptor signaling pathway and TNF signaling pathway, while multiple cellular immunity (IFI47, TRAF family) and oxidative stress (CAT, SODC, HSP70) genes were up-regulated. Inversely, compared with corals without interaction with algae at 30°C, the DEGs of corals interacted with C.taxifolia at 30°C, were remarkably enriched in apoptosis, NOD-like receptor signaling pathway, including the transcription factors such as Casp family, TRAF family. In conclusion, the density and chlorophyll a content of zooxanthella remained a fading tendency induced by macroalgae at ambient temperature. The oxidative stress and immune response levels of coral has been elevated at 30°C, but macroalgae alleviated the negative effects triggered by thermal stress.

For a long time, a company's Product Development Process (PDP) was seen as supporting the operations department, although PDP decisions and mistakes have a considerable impact on market performance. This is critical even in agriculture where bad habits and practices in the PDP can lead rural producers to great losses. Therefore, this research investigated the effect on the market performance of rural products (banana) in the southern region of Brazil, based on two analyses: (i) how sustainability practices support the PDP phases and (ii) how the phases of the Product Life Cycle Assessment (LCA) mediate sustainability practices and PDP phases. This study presents a quantitative analysis using Confirmatory Factor Analysis (CFA) and hierarchical ordinary least squares (OLS) regression of data obtained from a survey of 110 rural producers who directly participate in the banana production and planning process in southern Brazil. Our results shows that sustainability practices support the PDP, and we confirm that the product development and post-development phase has an effect on market performance. In addition, we identified that in the pre-development phase of the PDP, dealing with rural products (bananas), the maturity stage of the LCA mediates sustainability. In the PDP development phase, we concluded that rural families that develop economic and environmental practices with their products in the market growth phase may have reduced results. As for the post-development phase of the PDP, we conclude that when companies invest in environmental and social practices, there is a complete mediation of the effect, where these practices lose strength if the product is in the introduction and maturity phases in the market. As originality, our study contributed to demonstrate value on the product life cycle for the product development process in agriculture using sustainability practices through a systemic approach, filling the gap in the literature due to the lack of research on these areas seen in an integrated way.

Continuous technological progress places significant demands on the materials used in increasingly modern devices. An important parameter is often the long-term thermal resistance of the material. The use of heat-resistant polymer materials worked well in technologically advanced products. An economically justified direction in searching for new materials is the area of polymer nanocomposite materials. It is necessary to appropriately select both the polymer matrix and the nanofillers best able to demonstrate the synergistic effect. A promising area of exploration for such nanocomposites is the use of organosilicon polymers, which results from the unique properties of these polymers related to their structure. This review presents the results of the analysis of the most important literature reports regarding organosilicon polymer nanocomposites with increased thermal resistance. Particular attention was paid to modification methods of silicone nanocomposites focused on the increase of their thermal resistance related to the modification of siloxane molecular structure and by making nanocomposites using inorganic additives, carbon nanomaterials. Attention was also paid to such important issues as the influence of the dispersion of additives in the polymer matrix on the thermal resistance of silicone nanocomposites and the possibility of modifying the polymer matrix and permanently introducing nanofillers thanks to the presence of various reactive groups. The thermal stability mechanism of these nanocomposites was also analysed.

Age-related diseases place an intense and growing stress on healthcare systems. Numerous theories of ageing exist. Yet prediction, prevention and treatment limitations of age-related disease persist because we lack a complete aetiological understanding of their origins. Here we propose a new theory that aims to provide a blueprint-type understanding of ageing and disease aetiology, working across multiple scientific disciplines. Supported by specific examples, we demonstrate that the primary driver of much of age-related diseases is the futile triggering of specific molecular pathways in a pathological manner, which we term patho-pathways. Patho-pathways induce pathological cell, tissue and system changes in the form of hyperactivity (undesirable increased and new biological activities that are typical of age related disease). As part of patho-pathways, all wild-type (normal) genes have the potential to contribute to age-related diseases (though specific risk varies and can be formularised). In a domino-style effect, one patho-pathway typically triggers others, resulting in complex, but traceable, cascades. Utility, in terms of changing clinical and scientific practice, is derived from mapping these cascades to create Blueprint Maps that allow identification of biomarkers and therapeutic targets far upstream in the causal chain of events. Finally, our theory provides testable hypotheses concerning predictions of links between otherwise seemingly disparate diseases as well as new interventions into ageing.

Turner syndrome (TS) is caused by a complete or partial absence of an X or Y chromosome, including chromosomal mosaicism, affecting 1 in 2,500 female live births. Sister chromatid exchange (SCE) is used as a sensitive indicator of spontaneous chromosome instability. Cells from mosaic patients constitute useful material for SCE evaluations as they grow under the influence of the same genetic background and endogenous and exogenous factors. We evaluated proliferation dynamics and SCE frequencies of 45,X and 46,XN cells of 17 mosaic TS patients. In two participants, 45,X cells exhibited a proliferative disadvantage in relation to 46,XN cells after 72h of cultivation. The analysis of mean PI showed significant differences between 45,X and 46,XN lineages; however there were no intraindividual differences. On the other hand, mean SCE frequencies showed no differences between the two lineages, but there were intraindividual differences in 5 patients. The absence of mean SCE frequency differences between 45,X and 46,XN lineages may indicate that both were equally unstable, as more than 70% of the 46,XN lineages had an anomalous karyotype. However, 46,XN had a higher mean PI, suggesting that the amount of cells with a karyotype distinct from 45,X may increase with time in mosaic TS women.

Addressing the pressing challenge of global warming, reducing greenhouse gas emissions in the transportation sector is a critical imperative. Battery and fuel-cell electric vehicles have emerged as promising solutions for curbing emissions in this sector. In this study, we conducted a comprehensive life cycle assessment (LCA) for typical passenger vehicles, heavy duty trucks and city buses using either proton-exchange membrane fuel cells or Li-ion batteries with different cell chemistries. To ensure accuracy, we supplemented existing studies with data from the literature, particularly for the recycling phase, as database limitations were encountered. Our results highlight that fuel cell and battery systems exhibit large emissions in the production phase. Recycling can significantly offset some of these emissions, but a comparison of the technologies examined revealed considerable differences. Overall, battery electric vehicles consistently outperform fuel cell electric vehicles regarding absolute greenhouse gas emissions. Hence, we recommend prioritizing battery electric over fuel cell vehicles. However, deploying fuel cell electric vehicles could become attractive in a hydrogen economy scenario where other factors, e. g. the conversion and storage of surplus renewable electricity via electrolysis, become important.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

The temporary immersion system bioreactor named GreenTray®[2], [3]presents advantages over the existing ones. Firstly, there is no need to use forceps to move the shoots or plantlets in or out of the recipient, neither the use of scalpel to divide them. Secondly, the basis of the shoot can remain in the GreenTray® and can sprout again in several cycles of growth. These two characteristics reduce the costs in the process of micropropagation. Besides, shoots or plantlets development is enhanced by the aeration of the recipient, thus enriching with CO2 the recipient atmosphere. The chapter describes and provides images and values of interest in (1) the micropropagation process of some commercial Prunus or Pyrus rootstocks; (2) the plantlet growth under autotrophic conditions; and (2) the inoculation of plants with pathogens that reproduce in vitro the symptoms observed in vivo, using the GreenTray® bioreactor.

Anaerobic digestion is a biological process that transforms high-strength organic effluents into biogas with multiple benefits. However, concurrent with organics' biological transformation, a liquid phase with a high solid content is also derived from this process. Valorizing this fraction is not an easy task if an agronomic application cannot be considered as a suitable option. The thermal valorization of this fraction allows for energy extraction, but also gives rise to additional capital investment and increases the energy demand of the global process. In addition, the thermal treatment of digestate has to deal with a mineralized material. The changes in organic matter due to anaerobic stabilization were studied in the present manuscript, by evaluating the thermal behavior of samples, activation energy and organic transformation using FTIR spectroscopy. Digested samples of a mixture composed of manure and glycerin (5% v/v) were studied. The stabilization caused a dramatic decrease in aliphatic compounds, greatly increasing the mineral content of the sample. Thermal valorization of digestates must consider the lower energy content and more complex structure of these materials, with higher content of lignin and protein-type compounds.

This literature review provides an in-depth exploration of the research conducted on the investigation and measurement of residual stress (RS) in Wire Arc Additive Manufacturing (WAAM) products, particularly focusing on how process parameters influence the phenomenon. RS plays a crucial role in determining the mechanical behavior and structural integrity of WAAM components. This review article gives an understanding of the relationship between process parameters and RS to optimize the WAAM processes and ensure the durability of the final products. It also summarizes key findings, measurement techniques, challenges, and future directions in this evolving field. The review also analyzes a measurement of RS in the products of WAAM as a function of process parameters depending on examining various research studies, techniques, and methodologies employed in their studies. Experimental measuring techniques and numerical analysis of RS to determine the impacts of RS in mechanical response in products of WAAM were discussed. By offering a comprehensive overview of current research trends and insights, this review serves as a valuable resource to guide future investigations, fostering the advancement of WAAM as a robust and efficient manufacturing technology.

Keywords: Biomass pyrolysis, Chemical Looping Combustion, Life Cycle Assessment, Environmental Impacts, Carbon Footprint.

Electrical contacts are important circuit components with diverse industrial applications, and their failure can lead to multiple unwanted effects. Hence, the behavior of electrical contacts is a widely studied topic in scientific literature based on various approaches, tools, and techniques. The present study proposes a numerical modeling and simulation approach based on the Holm contact theory to study the dependence between the electric potential and the temperature within an electrical contact. Structured in 5 sections, the research was conducted using COMSOL Multiphysics software and its solid-state mechanics, electric current, and heat transfer modules in order to highlight contact behavior from mechanical, electrical and thermal points of view: the von Mises stress, contact force, the electric field amplitude, the variation of the electrical potential along the current path, the temperature gradient, and dependence of temperature along the contact elements edges were obtained by simulation and graphically represented. The results are in line with the expectations and with past research that was studied in the literature review.

This review aims to explore the intricate relationship between epigenetic mechanisms, stress, and affective disorders, focusing on how early life experiences and coping mechanisms contribute to susceptibility to mood disorders. Epigenetic factors play a crucial role in regulating gene expression without altering the DNA (deoxyribonucleic acid) sequence, and recent research has revealed associations between epigenetic changes and maladaptive responses to stress or psychiatric disorders. A scoping review of 33 studies employing the PRISMA-S (Preferred Reporting Items for Systematic Reviews and Meta-Analyses – Statement) guidelines investigates the role of stress-induced epigenetic mechanisms and coping strategies in affective disorders' occurrence, development, and progression. The analysis encompasses various stress factors, including childhood trauma, work-related stress, and dietary deficiencies, alongside epigenetic changes such as DNA methylation and altered gene expression. Findings indicate that specific stress-related genes frequently exhibit epigenetic changes associated with affective disorders. Moreover, the review examines coping mechanisms in patients with bipolar disorder and major depressive disorder, revealing mixed associations between coping strategies and symptom severity. While active coping is correlated with better outcomes, emotion-focused coping may exacerbate depressive or manic episodes. Overall, this review underscores the complex interplay between genetic predisposition, environmental stressors, coping mechanisms, and affective disorders. Understanding these interactions is essential for developing targeted interventions and personalized treatment strategies for individuals with mood disorders. However, further research is needed to elucidate specific genomic loci involved in affective disorders and the clinical implications of coping strategies in therapeutic settings.

Urea cycle disorders (UCDs) are common inborn errors of metabolism, with an incidence of one in 30,000 births. They are caused by deficiencies in any of six enzymes and two carrier proteins, the most common being Ornithine Transcarbamylase Deficiency (OTCD). OTCD results in impairment to excrete nitrogen, causing toxic buildup of ammonia with resultant encephalopathy. Hyperammonemia (HA) induces the conversion of glutamate to glutamine in the brain. Excess glutamine in the brain causes osmotic changes cerebral edema, changes in astrocyte morphology, and cell death. Acute symptoms of HA include vomiting, hyperventilation, seizures, and irritability. Long-term neurological changes include deficits in working memory and executive function. To date, there are no predictors of prognosis of infants with neonatal onset OTCD outside of plasma ammonia level at presentation and duration of hyperammonemic coma. We provide a comprehensive analysis of a 16-year-old male with neonatal onset of OTCD as an example of how brain biomarkers may be useful to monitor disease course and outcome. This male presented at 8 days post natal with plasma ammonia and glutamine of 677 and 4024 micromol/L and had a missense mutation in Exon 4 (p.R129H). Treatment included protein restriction, sodium benzoate, and citrulline, arginine, and iron. He suffered recurrent acute hyperammonemic episodes despite compliance, triggered by infections or catabolic stressors. We discuss the long-term effects of the hyperammonemic episodes by following MRI based disease biomarkers.

Observations of the X-ray binary system Her X-1 by the AstroSat Soft X-ray Telescope 1 (SXT) were carried out in 2020 through 2023 with the goals of measuring X-ray spectrum changes with the 35-day disk rotation phase and measuring eclipses at different 35-day phases. The four multi-day long observations were scheduled during: turn-on to Main High (MH) and MH rise; MH state; Short High (SH) state; and Low State (LS). 35-day phase was determined using monitoring observations with the Swift Burst Alert Telescope (BAT). Nine eclipses were observed at a range of 35-day phases, with at least one eclipse during each observation. Data with dips were separated from data without dips. The variation of X-ray spectral parameters vs. 35-day phase shows the following: eclipse parameters are nearly constant, showing that the scattering corona does not change with 35-day phase; dips show an increase in covering fraction but not column density compared to non-dip data; the 1 keV line normalization indicates an origin in a small region near the continuum emission region, likely the magnetospheric accretion flow from the inner disk onto the neutron star; and the change in blackbody normalization (area) shows that the emission region is much larger than the 1 keV emission region, and consistent with the inner edge of the accretion disk.

Some medical professional organizations have advocated for including the menstrual cycle as a vital sign in adolescence, but not in adulthood. However, documenting menstrual cycle patterns is not routine clinical or research practice. Vital signs are used to predict health outcomes, indicate needed treatment, and monitor a clinical course. They can help identify pathologies, affirm wellness, and are responsive to exposures. Here we review the scientific evidence showing how the menstrual cycle meets these criteria and should therefore be treated as a vital sign. Using key words and controlled vocabulary terms, we carried out multiple literature searches, prioritizing the inclusion of systematic reviews, meta-analyses, and clinical practice guidelines. This review describes how the menstrual cycle is a health indicator, can cyclically impact health conditions, and its associations with long-term post-menopausal health outcomes. We review exposures influencing the menstrual cycle, evidence underlying its use to optimize wellness, and available tools for documenting cycles. Supplementary materials include patient handouts on menstrual cycle tracking, and an index of related clinical practice guidelines and reviews by subject. The menstrual cycle is a vital sign from menarche through menopause, an underutilized but powerful tool for understanding gynecological and general health.

The comfort of human life depends on the quality, size, and reliability of the infrastructure projects. In the infrastructure systems, rapid growth is found, where the economic and sustainable impact has become a topic of significant concern for policies and government officials. To achieve con-straints of sustainable development, all the policies and actions over the infrastructure project's life cycle must be assessed. Decision-makers have adopted approaches for economic, social, and en-vironmental initiatives through Life Cycle Assessment (LCA) and Life Cycle Cost Analyses (LCCA) of infrastructure projects. The purpose of this review is to highlight the impact of per-forming LCA and LCCA in infrastructure projects. To achieve this goal, a systematic literature review methodology is adopted in which renowned databases, i.e., Web of Science, Science Direct, Emerald and Scopus were selected to extract the relevant literature. Using the PRISMA approach, 1251 publications were identified which were then filtered and 55 documents were included in the final review. In the extracted publications most, researchers were biased toward LCA and LCA individually, whereas few focused on integrated LCA and LCCA. The researchers assessed the costs and impact associated with the infrastructure project while there were less focused on the environmental cost. Besides this, techniques of economic, social, and environmental growth of infrastructure projects have been emphasized during the design phase because of substantial relations between infrastructure design and operation management. Moreover, a conceptual framework has been developed that will assist the decision-makers to consider the effects of LCA and LCCA on various aspects of the infrastructure project and how it impacts sustainability. In the last, a case study was performed to assess the developed framework with the incorporation of environmental impact cost.

Stress is a natural yet potentially harmful aspect of human life, necessitating effective management, particularly during overwhelming experiences. This paper presents a scoping review of personalized stress detection models using wearable technology. Employing the PRISMA-ScR framework for rigorous methodological structuring, we systematically analyzed literature from key databases including Scopus, IEEE Xplore, and PubMed. Our focus was on biosignals, AI methodologies, datasets, wearable devices, and real-world implementation challenges. The review presents an overview of stress and its biological mechanisms, details the methodology for the literature search, and synthesizes the findings. It shows that biosignals, especially EDA and PPG, are frequently utilized for stress detection and demonstrate potential reliability in multimodal settings. Evidence for a trend towards deep learning models was found, although the limited comparison with traditional methods calls for further research. Concerns arise regarding the representativeness of datasets and practical challenges in deploying wearable technologies, which include issues related to data quality and privacy. Future research should aim to develop comprehensive datasets and explore AI techniques that are not only accurate but also computationally efficient and user-centric, thereby closing the gap between theoretical models and practical applications to improve the effectiveness of stress detection systems in real scenarios.

The present work deals with the development of finite element methodology for obtaining the stress distributions in thick cylindrical HK40 stainless steel pipe that carry high temperature fluids. The material properties and loading are assumed to be random variables. Thermal stresses that are generated along radial, axial and tangential directions are computed generally using analytical expressions which are very complex. To circumvent such an issue, the probability theory and mathematical statistics have been applied to many engineering problems which allows to determine the safety both quantitatively and objectively based on the concepts of reliability. Monte Carlo simulation methodology is used to study the probabilistic characteristics of thermal stresses which is used for estimating the probabilistic distributions of stresses against the variations arising due to material properties and load. A 2-D Probabilistic finite element code is developed in MATLAB and the deterministic solution is compared with ABAQUS solutions. The values of stresses that are obtained from the variation of elastic modulus are found to be low as compared to the case where the load alone is varying. The probability of failure of the pipe structure is predicted against the variations in internal pressure and thermal gradient. These finite element framework developments are useful for the life estimation of piping structures in high temperature applications and subsequently quantifying the uncertainties in loading and material properties.

Surveys on the optimum seismic design of structures reveal that many investigations focus on how to minimize its initial cost while satisfying the performance constraints. Although reducing the initial cost while complying with the requirements of earthquake design codes of practice will significantly guarantee the life safety of occupants against earthquakes, it may still cause considerable economic losses to residents and fatalities. Accordingly, calculating the possible earthquake damages caused during the structure's lifetime may become essential from the optimal Life Cycle Cost (LCC) design point of view. LCC analysis is used to evaluate economic feasibility including construction, operation, occupancy, maintenance and end-of-life costs. For optimization, the population-based, meta-heuristic algorithm based on the Ideal Gas Molecular Movement (IGMM), has established its capability in solving highly nonlinear mono and multi-objective engineering problems. Therefore, this paper investigates the LCC -based mono and multi-objective optimum design of a 3-D four-story concrete building structure combined with the Endurance Time (ET) competence. The results show that, apart from substantially reducing the total number of analyses required, the proposed technique significantly affected dipping minor injury cost, rental, and income costs by 22%, 16%, and 16%, respectively. In total, a 10% reduction in all structural life-cycle costs was achieved, which could well be considered significant.

This study investigates stress perceptions, somatization, and coping strategies among 271 nursing and dentistry (n=126 and n=145, respectively), undergraduate and postgraduate students. For the study, an e-questionnaire was designed in a two-step process, uploaded in Google Forms and staying open for submissions during February 2024 in the School of Health Sciences, National and Kapodistrian University of Athens. In our sample, predominantly female (68.60%), the majority were undergraduates (80.10%). Females reported higher stress somatization (M=10.22, SD=5.23) compared to males (M=7.94, SD=6.14), with a moderate effect size (Cohen’s d=0.412, p

Electricity consumption is often the hotspot of life cycle assessment (LCA) of products, industrial activities, or services. The objective of this paper is to provide a consistent, scientific, region-specific electricity-supply-based inventory of electricity generation technology for national and regional power grids. Marginal electricity generation technology is pivotal in assessing impacts related to additional consumption of electricity. China covers a large geographical area with regional supply grids; these are arguably equally or less integrated. Meanwhile, it is also a country with internal imbalances in regional energy supply and demand. Therefore, we suggest an approach to achieve a geographical subdivision of the Chinese electricity grid, corresponding to the interprovincial regional power grids, namely the North, the Northeast, the East, the Central, the Northwest, and the Southwest China Grids, and the China Southern Power Grid. The approach combines information from the Chinese national plans on for capacity changes in both production and distribution grids, and knowledge of resource availability. The results show that nationally, marginal technology is coal-fired electricity generation, which is the same scenario in the North and Northwest China Grid. In the Northeast, East, and Central China Grid, nuclear power gradually replaces coal-fired electricity and becomes the marginal technology. In the Southwest China Grid and the China Southern Power Grid, the marginal electricity is hydropower towards 2030.

The endometrium, the inner mucosal lining of the uterus, undergoes complex molecular and cellular changes across the menstrual cycle in preparation for embryo implantation. Transcrip-tome-wide analyses have mainly been utilized to study the endometrial receptivity, the prerequisite for successful implantation, with most of the studies, so far, comparing the endometrial transcriptomes between (i) secretory versus proliferative endometrium or (ii) mid-secretory versus early-secretory endometrium. In the current study, we provide the complete transcriptome description of the endometrium across the entire menstrual cycle and, for the first time, comprehensively characterize the proliferative phase of the endometrium. Our temporal transcriptome analysis includes five time points: mid-proliferative, late-proliferative (peri-ovulatory phase), early-secretory, mid-secretory, and late-secretory phases. Thus, we exhaustively unveil the transitions between the consecutive proliferative and secretory phases, highlighting their unique gene expression profiles and possible distinct biological functions. Transcriptome analysis reveals many differentially expressed genes (DEGs) across the menstrual cycle, most of which are phase-specific. As an example of the coordinated gene activity, the expression profile of his-tone-encoding genes within the HIST cluster on chromosome 6 showed an increase in cluster activity during the late-proliferative and a decline during the mid-secretory phase. Moreover, numerous DEGs are shared among all phases. In conclusion, in the current study, we delineate the endometrial proliferative phase-centered view of transcriptome dynamics across the menstrual cycle. Data analysis highlights significant transcriptomic and functional changes occurring during the late-proliferative phase – an essential transition point from the proliferative to the secretory phase. Future studies should explore how the biology of the late-proliferative phase endometrium impacts the achievement of mid-secretory endometrial receptivity or contributes to molecular aberrations leading to embryo implantation failure.

According to previous studies the median raphe region (MRR) is known to contribute significantly to social behavior. Beside serotonin, there are reports of a small population of dopaminergic neu-rons in this region. Dopamine is linked to reward and locomotion, but very little has been known about its role in the MRR. To address that, we first confirmed the presence of dopaminergic cells in the MRR of mice (immunohistochemistry, RT-PCR) and humans (RT-PCR). Next, we used chemogenetic technology in mice containing Cre enzyme under the promoter of the dopamine transporter (DAT). With the help of an adeno-associated virus, artificial receptors were expressed in the dopaminergic cells of the MRR (DAT-MRR). Four weeks later, extensive behavioral charac-terization started 30 minutes after the injection of the artificial ligand (Clozapine-N-Oxide). Stimu-lation of DAT-MRR decreased social interest without influencing aggression and with an increase in social discrimination. Additionally, inhibition of the same cells increased the friendly social be-havior during social interaction test. No behavioral changes were detected in anxiety, memory and locomotion. All in all, dopaminergic cells were present both in the mice and human MRR, and manipulation of dopaminergic neurons of the MRR elicited a specific social response.

Students studying dentistry and nursing experience anxiety daily, which affects both their general well-being and academic achievement. Anxiety is exacerbated by several circumstances, such as stressors in one's personal life, clinical environment exposure, and academic expectations. To effectively regulate anxiety and support students' achievement, treatments that take these elements into account must be designed. In this study, 271 students from the National and Kapodistrian University of Athens, Greece's departments of dentistry and nursing were polled. Being the following resources, participants filled out an electronic questionnaire that was uploaded to Google Forms and assessed their levels of stress, anxiety, depression, resilience, hope, and spiritual well-being: a) the Depression, Anxiety, Stress Scale (DASS-21), b) the Functional Assessment of Chronic Illness Therapy-Spiritual Well-Being Scale (FACIT-12), c) the Adult Hope Scale (AHS), d) the Resilience Assessment Questionnaire (RAQ8), and e) the Brief Resilience Scale (BRS). Additionally, demographic data was gathered, such as gender, educational attainment, family income, and country of origin. Statistical analyses were performed to investigate the relationships between the variables, including hierarchical multiple linear regression and t-tests. The sample consisted of 271 students from the Department of Nursing (n=126, 46.5%) and Dentistry (n=145, 53.5%), with 68.60% of them being female, 80.10% being undergraduate students, and 48.30% being from Athens, the country's capital. Comparatively speaking, 74.50 percent of nursing students were female, while 62.80% of dental students were. Compared to dental students (2.10%), nurses (40.50%) participated in postgraduate studies at a higher rate. Compared to dental students (44.80%), nursing students reported a household income of just 13.90%, which is much less than €35,000. Anxiety was reported by 51.30% of participants overall, with dental students reporting higher anxiety than nursing students. Higher family wealth was associated with reduced stress levels, while female undergraduate students reported higher levels of anxiety than their male counterparts. Hope was a strong predictor of resilience, but stress and worry had a negative correlation. Promoting students' well-being and academic success requires effective stress-reduction and resilience-building techniques aimed to not only improve student performance but also support future healthcare professionals' personal sustainability and holistic growth.

The problems of modeling the human bladder and its stress-strain state under external static influence were considered. A method for identification of the anisotropic biomechanical characteristics of bladder tissue was proposed. A FEM model was created, which accepts into regard that the bladder is surrounded by fiber and affected by surrounding organs, and partially protected by pelvic bones. The model considered the presence of constant hydrostatic pressure on the walls of the bladder when it is full. It has been shown that isotropic mechanical characteristics of biological tissue can be used for studying the deformed state of a filled bladder if the filled bladder 300 ml is considered as initial non-deformed stage. This was shown by modeling and verification the effect of the external static force on the bladder. Numerical experiments were conducted based on the constructed model. To validate the results obtained, a series of natural experiments on the effect of external pressure on the bladder under ultrasound control was conducted. In the future, it is planned to use the constructed model to study rupture deformations of the bladder under the influence of static and dynamic loads.

Correlations among estrus cycle, pyometra, and canine diabetes mellitus (CDM) have been described since the late 1950s, and substantial progress in understanding mechanisms beyond was achieved nowadays. Progesterone-related diabetes mellitus (PRDM) in dogs is known for its particular potential for diabetes remission. Thus, a deep understanding of the physiopathological aspects involved is crucial to postulate treatment guidelines to improve the PRDM remission rate, as well as to inform preventive measures. This narrative review aims to provide relevant detailed information on 1) canine estrus cycle and its impact on CDM etiology and management, 2) the role of pyometra as a further cause of insulin resistance, and 3) useful individual therapeutic and preventive strategies. Pharmacological annulment of progesterone effects, as well as inflammatory and progesterone-related conditions resolution in association with adequate exogenous insulin therapy, and residual beta cell function, are key aspects to achieve remission, or at least to improve diabetic clinical control. In this way, spaying should be considered mandatory in most PRDM cases. Preventive measures against CDM can include spaying recommendations; however, individual-based recommendations should be considered since castration may be associated with some long-term health issues.

Hyperspectral imaging data holds great potential for the different stages of the mining life cycle in active and post-mining environments. However, the technology has yet to reach the stage of large-scale industrial implementation and acceptance. While hyperspectral satellite imagery can achieve high spectral resolution, signal-to-noise ratio (SNR) and global availability with break-through satellite systems like EnMAP, EMIT and PRISMA, limited spatial resolution poses chal-lenges for sectors like mining, which require decimetre to centimetre scale resolution for applica-tions such as reconciliation, ore/waste estimates, geotechnical assessments and environmental monitoring. Hyperspectral imaging from drones (referred to herein as Uncrewed Aerial Systems; UASs) offers high spatial resolution data relevant to the camp/ mine scale, with the capability for frequent, user-defined re-visit times. This has been made possible by the miniaturization of hy-perspectral imaging systems. Collection of data in the visible to near and shortwave infrared (VNIR-SWIR) wavelength regions enables the detection of different minerals and surface altera-tion patterns potentially revealing crucial information for exploration, extraction, re-mining, waste remediation, and rehabilitation. In this paper, we provide a review of relevant studies de-ploying hyperspectral imaging in or applicable to the mining sector, especially for the use of hy-perspectral VNIR-SWIR Uncrewed Aerial Systems. Where required, we draw on previous in-sights derived from satellite or ground-based systems. We also discuss UAS survey planning, and sampling considerations for validation and interpretation.

The Carnot cycle and the attendant notions of reversibility and entropy are examined. It is shown how the modern view of these concepts still correspond to the ideas Clausius laid down in the nineteenth century. As such, they reflect the outmoded idea current at the time that heat is motion. It is shown how this view of heat led Clausius to develop the entropy of a body based on the work that could be done in a reversible process rather than the work that was actually done. In consequence, Clausius built into entropy a conflict with energy conservation, which is concerned with actual changes in energy. In this paper, a macroscopic formulation of internal mechanisms of damping based on rate equations for the distribution of energy within a gas. It is shown that work processes involving a step-change in external pressure, however small, are intrinsically irreversible. However, under idealised conditions of zero damping the gas inside a piston expands and traces out a trajectory through the space of equilibrium states. Therefore, the entropy change due to heat flow from the reservoir matches the entropy change of the equilibrium states. This trajectory can traced out in reverse as the piston reverses direction, but if the external conditions are adjusted appro-priately, the gas can be made to trace out a Carnot cycle in P-V space. The cycle is dynamic as opposed to quasi-static as the piston has kinetic energy equal in difference to the work done in-ternally and externally.

The amino acid proline accumulates in plants during abiotic stresses such as drought and salinity and is considered a reliable marker of environmental stress. While its accumulation is well established, its precise role in stress tolerance and its underlying molecular mechanism remain less clear. To address these issues, we performed a meta-analysis - a robust statistical technique that synthesizes results from multiple independent studies while accounting for experimental differences. We focused on 16 physiological and morphological parameters affected by drought and salt stress in transgenic plants expressing proline metabolic genes. For each parameter, we calculated the effect size as the response ratio (RR), which represents the logarithm of the mean value in the transgenic group over the mean value of the control group (lnRR). Under stress, most parameters exhibited significantly higher response ratios in the transgenic group, confirming the beneficial effects of proline during drought and salt stress. Surprisingly, under non-stressed conditions, most stress markers showed no significant differences between transgenic and non-transgenic plants, despite elevated proline levels in the former. These results suggest that the benefits of proline may be related to proline catabolism or may only become apparent during stress, possibly due to interactions with reactive oxygen species (ROS), which accumulate predominantly under stress conditions.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

As a result of climate change, the Mediterranean Sea has been exposed to an increase in frequency and intensity of marine heat waves in the last decades, some of which caused mass mortality events of benthic invertebrates, including sponges. Sponges are an important component of benthic ecosystems and can be the dominant group in some rocky shallow-water areas in the Mediterranean Sea. In this study, we exposed the common shallow-water Mediterranean sponge Chondrilla nucula (Demospongiae: Chondrillidae) to six different temperatures for 24 h, ranging from temperatures experienced in the field during the year (15, 19, 22, 26, 28 °C) and above normal temperatures (32 °C) and metabolic (respiration rate) and behavioural (clearance rate) were measured. Both respiration and clearance rates were affected by temperature. Respiration rates increased at higher temperatures but were similar between 26 and 32 °C treatments. Clearance rates decreased at temperatures > 26 °C, indicating a drop in food intake that was not reflected by respiration rates. This decline in feeding, while maintaining high respiration rates, may indicate a negative energy balance that could affect this species under chronic or repeated thermal stress exposure. C. nucula will probably be a vulnerable species under climate change conditions, affecting its metabolic performance, ecological functioning and the ecosystem services it provides.

Pregnancy is a complex biological process which is associated with significant metabolic and hemodynamic changes of the maternal body which allow a normal fetal growth. The inability to adapt to these changes can affect the cardiovascular health. During pregnancy, women may experience mood swings, anxiety and emotional ambivalence. These symptoms can lead to stress and have a negative impact on the mental well-being of expectant mothers. It is crucial to know the aspects that can influence the development of cardiovascular problems among pregnant women in order to manage these cases properly. The current narrative review explores and summarizes the evidence regarding the impact of stress and anxiety on cardiovascular health in pregnant women. Understanding the physiological adaptations that the body undergoes throughout pregnancy is crucial for educating and supporting individuals as well as healthcare professionals. This enables them to recognize any risk factors or pathological conditions that may exacerbate pregnant women's health. In order to reduce maternal morbidity and mortality from cardiovascular disease, a psychological and cardiovascular risk factor screening that is done either before or during pregnancy may be able to identify situations that call for particular medical and/or psychological therapies.

Salinity stress emerges as an important menace to global food security, particularly affecting susceptible crops such as common bean plants (Phaseolus vulgaris L.). The disruption of ion balances caused by salt stress withing plants cells reduces water and nutrient absorption, and hampers growth and productivity. Sacchorhiza polyschides, a brown macroalga rich in essential elements, and macrominerals, has drawn attention as a natural biostimulant, being a potential remedy to bolster crop resilience against salt stress. This study delves into the effect of water extracts of Sacchorhiza polyschides (SPE) across varying concentrations (1%, 2%, and 5%) in common bean plants under salt stress (68.4 mM NaCl) conditions. Two different methods of application were used: by spraying the aerial part of the plant or by irrigation together with the watering solution. The effects of both systems of application were studied on the aerial parts of the plants. SPE exhibited significant enhancements in morphological parameters, chlorophyll content, carbon-nitrogen activities, and antioxidant enzymatic system activities, alongside increasing osmolyte accumulation, compared to salt-stressed plants without biostimulation. Moreover, SPE reduced reactive oxygen species (ROS) levels caused by salt stress, mitigating lipid peroxidation. The concentrations of 2% and 5% SPE applied by spraying showed the most significant results in most of the parameters analyzed. By shedding light on the underlying science behind this biostimulant effect, this research underscores the potential of SPE to enhance crop resilience and augment food production in salt-challenged environments.

This paper details the comprehensive activities conducted in a laboratory setting to assess the Structural Health Monitoring (SHM) of prefabricated building envelopes. Aimed at enhancing the structural evaluation of buildings, the focus of this research lies in employing nondestructive sensors for SHM with the objective to advance in the understanding and assessment of facade conditions. The paper outlines the methodologies employed, starting with a modal analysis to define the structural vibration's modal frequency. Subsequently, tests were defined and executed to validate building envelope compliance in case of stress typical of high-rise building. Throughout these tests, continuous monitoring of the façade was conducted using both conventional (accelerometers, extensimeter washers) and non-conventional sensors (Fiber Optic Sensing) The gathered data underwent thorough processing and analysis to provide an overall perspective on the structure's behavior during the stress test. The investigation aimed to identify whether specific physical phenomena correlate with distinct signals and to evaluate if continuous façade monitoring over the building's lifespan aids in preventing potential structural damage. Moreover, two modal analyses were conducted to compare final data and frequencies with earlier data, enabling the detection of any structural alterations. The results from compliance testing and structural analysis yielded noteworthy insights contributing to the evolving field of structural health monitoring, offering valuable findings that advance our ability to proactively manage and maintain the integrity of building structures.

Temperature Cycle Induced Deracemization (TCID) offers a promising approach to obtain enantiopure solids from racemic mixtures. By combining rapid racemization in solution and temperature swings, homochirality is theoretically achieved. Despite theoretical expectations of doubled yields compared to traditional chiral separation methods, such as in Preferential Crystallization, experimental validation remains lacking. We applied TCID to (1-(4-chlorophenyl)-4,4-dimethyl-2-(1H-1,2,4-triazol-1-yl) pentan-3-one) (Cl-TAK), introducing a post-TCID cooling step to enhance yield and a washing step to augment enantiopurity. This refinement yielded an 89.8% mass yield with 99.1% enantiomeric excess in the crystal phase (c.e.e.) within 24 hours on an 8.75g scale, showcasing improved performance with insignificant process duration extension. Additionally, we explored the stochasticity of deracemization, observing the development from low initial crystal enantiomeric excesses(1-6% c.e.e0) at a 2.5 g scale. Kinetic analysis revealed that a 2% c.e.e0 effectively mitigates chiral flipping risks and induction time in our system. Our study underscores the potential for reduced initial c.e.e. to expedite deracemization and presents a straightforward method to optimize yield and purity, facilitating industrial application.

In steel structures, oblique thin steel plates serve as panel zones in structures spanning large spaces (e.g., warehouses and gymnasiums). Considerable research has been conducted on the shear buckling of panels due to seismic loads acting on a structure. Conversely, under snow or wind loads, the panel zone may experience compressive and tensile stresses simultaneously from two directions. Considering the economic preference for thin steel plates, evaluating the elastic critical local buckling stresses in the panel zone under biaxial normal stress may provide essential information to structural engineers. In this study, an elastic buckling analysis based on the energy method is performed to clarify the impact of panel geometry and boundary conditions on the elastic local buckling stresses of oblique panel zones. As confirmed, the buckling stresses derived from the energy method could simulate the local buckling stresses with accuracy comparable to that of finite element analysis, and an engineer-friendly design formula was proposed. Finally, we determined the correlation of the buckling stresses under biaxial stresses and presented a method for evaluating this correlation. Engineers can utilize the provided design equations to more efficiently and accurately calculate buckling loads, facilitating safer and more economical design of structures with oblique plates.

Saikosaponin (SS) a is a compound with various pharmacological properties and easily degraded into SSb1 and SSg in acid condition. In present work another two new degradation products of SSa formed under acid hydrolytic condition were detected and isolated by analytical and semi-preparative liquid chromatography technology, furthermore their structures were characterized as hydroxyl-saikosaponin a and SSb2 by spectral analysis, which is not only essential in stability-indicating method development and validation but also could be used as a worst case to assess the analytical method performance of SSa. Moreover their structural transformation pathways were also proposed.

The thermal degradation behaviour of 10:90 and 90:10 blends of Polyethylene Terephthalate (PET) and petroleum coke has been investigated using mechanical alloying (milling) at 300 rpm and for periods up to 1-10 hours. Milled specimens were characterised using SEM and x-ray diffraction; their thermal degradation behaviour was investigated using thermo-gravimetric analyser (TGA) for temperatures up to 1200°C. Whereas PET specimens showed a tendency towards flattening out and increased surface area during collisions in ball mills, petroleum coke particles tended to break down into smaller particles. 10:90 and 90:10 blends of PET and coke showed significant microstructural evolution with increasing speeds and time including fracture, strain hardening and re-welding. X-ray diffraction results showed clear evidence for increasing amorphous component in petroleum coke without much influence on PET crystallinity. Thermo-gravimetric results showed a significant increase in the overall degradation and much higher weight losses associated with mechanical alloying. This study has shown that mechanical alloying could be used to modify the degradation behaviour of coke/plastic blends and corresponding yield during pyrolysis with implications for plastic waste management.

The quiet-time solar wind electrons feature non-thermal characteristics when viewed from the perspective of their velocity distribution functions. They typically have an appearance of being composed of a denser thermal “core” population plus a tenuous energetic “halo” population. At first, such a feature was empirically fitted with the Kappa velocity space distribution function, but ever since the ground-breaking work by Tsallis, the space physics community has embraced the potential implication of the Kappa distribution as reflecting the non-extensive nature of the space plasma. From the viewpoint of microscopic plasma theory, the formation of non-thermal electron velocity distribution function can be interpreted in terms of the plasma being in a state of turbulent quasi equilibrium. Such a finding brings forth the possible existence of a profound inter-relationship between the non-extensive statistical state and the turbulent quasi-equilibrium state. The present paper further develops the idea of solar wind electrons being in the turbulent equilibrium, but unlike the previous model, which involves the electrostatic turbulence near the plasma oscillation frequency (i.e., Langmuir turbulence), the present paper considers the impact of transverse electromagnetic turbulence, particularly, the turbulence in the whistler-mode frequency range. It is found that the coupling of spontaneously-emitted thermal fluctuations and the background turbulence leads to the formation of non-thermal electron velocity distribution function of the type observed in the solar wind during quiet times. This demonstrates that the whistler-range turbulence represents an alternative mechanism for producing the Kappa-like non-thermal distribution, especially close to the Sun and in the near-Earth space environment.

Abiotic stress, especially drought stress poses a significant threat to the terrestrial plant growth, development, and productivity. Although mulberry have great genetic diversity and extensive stress tolerant traits in agroforestry systems, only a few reports offer preliminary insight into biochemical responses of mulberry leaves under drought conditions. In this study, we performed a comparative metabolomic and transcriptomic analysis on the “drooping mulberry” (Morus alba var. Pendula Dippel) under PEG-6000-simulated drought stress. Our research revealed that drought stress significantly enhanced flavonoid accumulation and up-regulated the expression of phenylpropanoid biosynthetic genes. Furthermore, the activities of superoxide dismutase (SOD), catalase (CAT) and malondialdehyde (MDA) content were elevated. In vitro enzyme assays and fermentation tests indicated the involvement of flavonol synthase/flavanone 3-hydroxylase (XM_010098126.2) and anthocyanidin 3-O-glucosyltransferase 5 (XM_010101521.2) in the biosynthesis of flavonol aglycones and glycosides, respectively. The recombinant MaF3GT5 protein was found to recognize kaempferol, quercetin, and UDP-glucose as substrates, but not 3-/7-O-glucosylated flavonols and UDP-rhamnose. MaF3GT5 is capable of forming 3-O- and 7-O-monoglucoside, but not di-O-glucosides, form kaempferol. This implies its role as a flavonol 3, 7-O-glucosyltransferase. The findings from this study provided insights into the biosynthesis of flavonoids and could have substantial implications for the future diversified utilization of mulberry.

Flap surgery is a common method used to cover defects following tumor ablation, trauma, or infection. However, insufficient vascularity in the transferred flap can lead to flap necrosis and failure. Proper postoperative monitoring is essential to prevent these complications. Recently, research has explored the use of infrared thermal imaging in plastic surgery, leading to its clinical application. This study investigates the use of a forward-looking infrared (FLIR) camera to monitor blood flow in flaps. In the study, 28 rats underwent reverse McFarlane flap surgery, and their flaps were analyzed using a FLIR thermal imaging camera seven days post-surgery. Additionally, thermal images of flaps were taken on postoperative days 0, 1, 2, 3, and 7 in 22 patients. The study focused on temperature differences between normal skin and the perforator compared to the average flap temperature. Results showed that the temperature difference was higher in the necrosis group and increased over time in cases of total necrosis. A lower perforator temperature compared to the flap's average indicated vascular compromise, potentially leading to flap failure. The FLIR camera, being contact-free and convenient, shows promise for understanding and inferring the clinical progression of flaps in postoperative monitoring.

Plant cells' ability to withstand abiotic stress is strongly linked to modifications in their mechanical characteristics. Nevertheless, the lack of a workable method for consistently tracking plant cell mechanical properties severely restricts our comprehension of the mechanical alterations in plant cells under stress. With Polyethylene Glycol (PEG6000), we created a drought-like environment, and we used the Double Resonator Piezoelectric Cytometry (DRPC) method to dynamically and non-invasively track changes in the stress (ΔS) created and viscoelasticity (storage modulus G' and loss modulus G") of protoplasts and suspension cells of rice during drought stress. The findings demonstrate that, rice suspension cells and protoplasts react mechanically differently to 5%–15% PEG6000 stress, implying distinct resistance mechanisms. However, neither of them can withstand 25% PEG6000 stress, they respond mechanically similarly to 25% PEG6000 stress. The results of DRPC are further corroborated by the morphological alterations of rice cells and protoplasts observed under an optical microscope. To sum up, the DRPC technique functions as a precise cellular mechanical sensor and offers novel research tools for the evaluation of plant cell adversity and differentiating between the mechanical reactions of cells and protoplasts under abiotic stress.

Bicyclic peptides have attracted the interest of pharmaceutical companies because of their remarkable properties putting them on a new path in medicine. Their conformational rigidity that improves proteolytic stability, leads to rapid penetration into tissues via any possible route of administration and elimination, occurring by renal metabolism, is of great importance for people with a history of liver diseases. In addition, each ring can function independently, making them extremely versatile molecules for further optimization. In this paper we compared the potentiometric and spectroscopic properties studied by UV-Vis, MCD, and EPR, of four synthetic analogues of the bi-cyclic peptide c(PKKHP-c(CFWKTC)-PKKH). In particular we correlated the structural and spectral properties of complexes with coordinating abilities toward Cu(II) ions of MCL (Ac-PKKHPc(CFWKTC)PKKH-NH2) that contains the unbinding cycle and N- and C-terminal linear parts, with two histidine residues, one per part; two monocyclic ligands containing one histidine residue, both in the N-terminal position i.e., MCL2 (Ac-PKKHPc(CFWKTC)PKKS-NH2) and in the C-terminal position i.e., MCL3 (Ac-PKKSPc(CFWKTC)PKKH-NH2), respectively, and the linear structure LNL (Ac-PKKHPSFWKTSPKKH-NH2).

Electric heating and solid thermal storage system (EHSTSS) is widely used in district clean heating and the flexibility adjustment of combined heat and power (CHP) unit. It has been an effective way to absorb renewable energy. Aiming at the thermal design calculation and experimental verification of EHSTSS, the thermal calculation and the heat transfer characteristics of the EHSTSS are investigated in this paper. Firstly, a thermal calculation method for the EHSTSS is proposed in the paper. The calculation flow and calculation method for key parameters of heating system, heat storage system, heat exchange system and fan-circulating system in the EHSTSS are studied. Then, the instantaneous heat transfer characteristics of the thermal storage system (TSS) in the EHSTSS are analyzed, and the heat transfer process of ESS is simulated by FLUENT software. The uniform temperature distribution in the heat storage and release process of the TSS verifies the good heat transfer characteristics of the EHSTSS. Finally, EHSTSS test verification platform is built, and the historical operation data of the EHSTSS is analyzed. During the heating and release thermal process, the maximum temperature standard deviation of each temperature measurement point is 28.3℃ and 59℃respectively. The correctness of the thermal calculation of the EHSTSS is verified.

In this paper, the deformation behavior of S32750 duplex stainless steel during low cycle fatigue was studied by controlling number of cycles. The microstructure of the specimens under different cycles was characterized by optical microscope (OM), scanning electron microscope (SEM), electron backscatter diffraction (EBSD) and transmission electron microscope (TEM). Microhardness of two phases was measured by a digital microhardness instrument. The results showed that the microhardness of ferrite increases significantly after the first 4000 cycles, while the austenite shows a higher strain hardening rate after fatigue fracture, and the microhardness of ferrite and austenite increases by 23 HV and 87 HV, respectively. Two-phase kernel average misorientation (KAM) diagram showed that the continuous accumulation of plastic deformation easily leads to the initiation of cracks inside the austenite and at the phase boundaries. The evolution of dislocation morphology in two phases was obviously different. With the increase of cycle number, the dislocation in ferrite gradually transforms from dislocation bundles and dislocation array to sub-grain structure, while the dislocation in austenite gradually develops from dipole array to ordered Taylor lattice network structure.

The complexity of plastic polymers and even more so of additives has increased enormously in recent years. This makes the high-quality recycling of mixed plastic waste considerably more difficult. Some additives have now been strictly regulated or even completely banned for good reasons ('legacy additives'). Material or mechanical recycling generally utilises old plastics that still contain these substances. Consequently, products that are manufactured using such recyclates are contaminated with these harmful substances. We therefore recommend avoiding the use of these recyclates for products with intensive contact with consumers until further notice. We also show that the climate policy challenges for the plastics (and chemical) industry necessitate a defossilisation ('feedstock change'). This turnaround can only succeed if solely high-quality recycling takes place in future; recyclates should primarily replace virgin plastics. This can only work if used plastics with a high degree of homogeneity and known formulation are collected separately, as is already the case today with PET bottles. In this context, we would like to point out inconsistencies in the current legislation on the European emissions trading system.

The purpose of this study is to investigate the influence of heat stress on some biochemical parameters in the blood of dairy cows raised in Bulgaria. The study was conducted on a dairy farm with a capacity of 500 cows, Holstein breed, raised in free-group housing in individual resting boxes. The research was carried out over three seasons: spring, summer, and autumn, with a total of 90 blood samples collected from the cows raised on the farm - 30 blood samples for each season, including cows from the 30th to the 60th day of lactation. Temperature and humidity data were obtained from the nearest meteorological station to the farm. Based on this data, the minimum, average, and maximum values of the temperature-humidity index were calculated. The analysis of variance revealed that the month of the study significantly influenced the following blood parameters: glucose, urea, total protein, cortisol, prolactin, and Ca (P < 0.001). Analysis of the data expressed by LS mean values clearly shows that during the hot months, dairy cows experience a deficit of energy from carbohydrate sources, which they compensate for from other non-carbohydrate sources. Confirmation of this is seen in the blood glucose values, which during the summer are 1.50 mmol/l, approximately twice as low as the values measured during spring and autumn. Regarding urea concentration, a final product of protein metabolism, the values recorded during the summer are 5.3 mmol/l, 1.5 times higher compared to other study periods. As a result of the metabolic load on the liver, the values of hepatic enzymes (ASAT and ALAT) decrease during the summer months, respectively to 93.92 and 17.68 U/L. Cortisol levels in the blood during the summer were registered at 50.92 nmol/l, indicating that cows are under stress. Values for prolactin are of interest, with the highest values being recorded in spring - 1.09 mlU/I. During the summer and autumn studies, the values are 0.99 and 0.89 mlU/I, respectively. A similar trend of decreasing values from spring to autumn season is observed in total blood protein, namely 89.93; 81.99, and 74.36 g/l.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

Adult neurogenesis involves generation of functional neurons from neural progenitor cells, which have the potential to complement and restore damaged neurons and neural circuits. Therefore, the development of drugs that stimulate neurogenesis represents a promising strategy in stem cell therapy and neural regeneration, greatly facilitating the reconstruction of neural circuits in cases of neurodegeneration and brain injury. Our study reveals that compound A5, previously designed and synthesized by our team, exhibits remarkable neuritogenic activities, effectively inducing neurogenesis in neural stem/progenitor cells (NSPCs). Subsequently, transcriptome analysis using high-throughput Illumina RNA-seq technology was performed to further elucidate the underlying molecular mechanisms by which compound A5 promotes neurogenesis. Notably, comparative transcriptome analysis showed that the up-regulated genes were mainly associated with neurogenesis and the down-regulated genes were mainly concerned with cell cycle progression. Furthermore, we confirmed that compound A5 significantly affected the expression of transcription factors related to neurogenesis and cell cycle regulatory proteins. Collectively, these findings identify a new compound with neurogenic activity and may provide insights into drug discovery for neural repair and regeneration.

Bone drilling is a common procedure used to create pilot holes for inserting screws to secure implants for fracture fixation. However, dis process can increase bone temperature, teh excessive heat can lead to cell death and thermal osteonecrosis, potentially causing early fixation failure or complications. We conducted a three-dimensional dynamic elastoplastic finite element model to evaluate teh propagation and distribution of heat during bone drilling and assess teh thermally TEMPeffected zone (TAZ) dat may lead to thermal necrosis. dis model investigates teh parameters influencing bone temperature during bone drilling, including drill diameter, rotational speed, feed force, and predrilled hole. Teh results indicate dat our FE model is sufficiently accurate in predicting teh temperature rise TEMPeffect during bone drilling. Teh maximum temperature decreases exponentially wif radial distance. When teh feed forces are 40 and 60 N, teh maximum temperature does not exceed 45 °C. However, wif feed forces of 10 and 20 N, both teh maximum temperature exceeds 45 °C wifin a radial distance of 0.2 mm, indicating a high-risk zone for potential thermal osteonecrosis. Wif teh two-stage drilling procedure, where a 2.5 mm pilot hole is pre-drilled, teh maximum temperature can be reduced by 14 °C. dis suggests dat higher feed force and rotational speed and/or using a two-stage drilling process could mitigate bone temperature elevation and reduce teh risk of thermal osteonecrosis during bone drilling.

Rhododendron chrysanthum Pall., live in Changbai Mountain being exposed to chilling temperature, high light intensities and water scarcity condition. To adapt to the harsh environment, the cold resistance mechanisms of R. chrysanthum have been successfully evolved in the long-term adaptive process. In our present work, the methods of proteomics combined with physiological and biochemical analyses were used to investigate the effects of cold stress on the photosynthesis and antioxidant system of Rhododendron chrysanthum Pall. and the molecular mechanisms involved in cold resistance of plants. A total of 153 photosynthesis related proteins were identified in present work, of which 7 proteins including Rubisco large subunit (rbcL) were up-regulated in experiment group (EG) compared with control group (CG). Simultaneously, four chlorophyll fluorescence parameters were measured in present study. The results showed that the maximum photochemical efficiency of photosystem II (Fv/Fm), actual quantum yield of PSII (Y(II)) and photochemical quenching (qP) were significantly higher in EG, whereas the non-photochemical quenching (NPQ) was notably decreased. Cold stress could lead to a significant reduction in electron transport rate (ETR) accompanied with an increase in excitation pressure (1-qP). The abundance of PetE which involved in the plants photosynthetic electron transfer was also significantly influenced by cold stress. Moreover, the up-regulated expressions and higher levels of enzymatic activities of Glutathione peroxidase (GPX) and Ascorbate peroxidases (APXs) were detected in EG. All these changes which can help plants to survive in low temperature are considered as the crucial parts of cold tolerance mechanisms. These results revealed that photosynthesis and redox adjustment play significant roles in the defense of cold-induced damage.

Separase is a key cysteine protease to separate sister chromatids through digestion of cohesion ring that inhibits chromosome segregation as trigger of metaphase–anaphase transition in eukaryotes and highly regulated its activity by binding with securin and cyclinB-CDK1 complex. Those bindings prevent proteolytic activity of separase until the onset of anaphase. Chromosome missegregation and aneuploidy are frequently observed in malignancies. However, there are some difficulties for biochemical examinations due to instability of separase in vitro and a few spatiotemporal resolution approaches monitoring live separase activity throughout mitotic processes. Here we have developed FRET-based molecular sensors including GFP variants with separase cleavable sequences as donor and covalently attached fluorescent dye as acceptor molecules applicable to conventional live cell imaging and flow cytometric analysis because of efficient live cell uptake. We investigated performance of equivalent molecular sensors localized or not localized inside nucleus under cell cycle control using flow cytometry. Synchronized cell cycle progression rendered significant separase activity detections in both molecular sensors. We obtained consistent outcomes with localized molecular sensor introduction and cell cycle control by fluorescent microscopic observations. We thus established live cell separase activity monitoring systems specifically or statistically that could lead to elucidate separase properties in detail.

Plant hormones regulate the adaptive responses to various biotic and abiotic stress factors. Applied exogenously they trigger the natural plant defense mechanisms, a feature that could be implemented in strategies for supporting crop resilience. The potential of exogenous cytokinin-like acting compound (kinetin), the auxin analogue 1-naphtyl acetic acid (NAA), abscisic acid (ABA) and the ethylene-precursor 1-aminocyclopropane-1-carboxylic acid (ACC) to mitigate dehydration was tested on Lactuca sativa (lettuce) grown on 12% polyethylene glycol (PEG). Priming with different blends containing these plant growth regulators applied in bioequivalent concentrations was evaluated through biometric measurements and biochemical analyses. The combined treatment with the four plant hormones exhibited the best dehydration protective effect. The antioxidative enzyme profiling of the PGR-primed individuals revealed increased SOD, catalase and peroxidase activity in the leaves. Immunodetection of higher levels of the rate-limiting enzyme for proline biosynthesis (delta-pyroline-5-carboxylate synthase) in the primed plants coincided with a significantly higher content of the amino acid measured in the leaves. These plants also accumulated particular dehydrin types, which may have contributed to the observed stress-relieving effect. The four-component hormonal mix applied by spraying or through the roots exerted similar stress-mitigating properties on soil-grown lettuce subjected to moderate drought.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

Citrus waste has been used as a source of bioplastic research in different ways. Because the juice industry produces significant amounts of residue each year, it would be advantageous to use the byproducts in the creation of new materials. For many years, researchers have been investigating an environmentally friendly way to take citrus and other organic waste and turn it into polymers that may be used, for instance, to produce bio-based and biodegradable films for food packaging. The goal of this study is to create biofilms from orange (OW) and ginger waste (GW) using an ultrafine grinder and study the films' properties. Since pectin has the ability to gel and because cellulosic fibres are strong, citrus waste has been studied for its potential to produce biofilms. After being washed, dried, and milled, orange and ginger waste were shaped into films using a casting process. Tensile testing was used to determine the mechanical properties of biofilms, while dynamic mechanical thermal analysis (DMTA), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC) were used to determine their thermal properties. As the number of grinding cycles increased, the suspension's viscosity increased from 29 to 57 mPa.s for OW and from 217 to 376 mPa.s for GW while the particle size in the suspension significantly decreased. For OW and GW films, the highest tensile strength was 17 MPa and 15 MPa, respectively. The maximum strain obtained among all films was 4.8%. All the tested films were stable up to 150°C, and maximum degradation occurs after 300°C.

An eight-sided prism sample, obtained from a hot-rolled AZ31 magnesium alloy sheet, was compressed at room temperature along the transverse direction to investigate the influence of local strain on twinning behavior using electron backscatter diffraction (EBSD) measurements. The octagonal surface of the sample was divided into distinct regions based on hardness distribution and metallographic observations. The EBSD maps of different areas show significant variations, suggesting that these areas experienced different local strain conditions. The EBSD measurements provided detailed data from three distinct regions, with the strain state known in two regions and uncertain in the third. The combined analysis of the Schmid factor (SF) and the strain compatibility factor (m') was employed to study twin variant selection. The comparison of twinning behavior in different regions showed that the strain compatibility factor offered a more comprehensive explanation for the observed twinning pattern in the region with local shear strain.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Australia’s avian species are unique and diverse. Due to the dramatic changed in distribution, physiology, and behaviour caused by both changing climatic conditions and human activities, Australian bird species becomes highly vulnerable to health-related factors such as impact injury and vehicle trauma, as well as environmental-related stressors such as animal attack and abnormal behaviours. This is reflected in increasing number of avian patients received by wildlife hospitals. The most common outcome of avian species in wildlife hospitals was euthanasia, only few of them were released back into their ecosystem. During the process of bird rescue and rehabilitation, stress can be caused by various stressors such as injury, infection, trauma, shock and stressful environment in wildlife hospitals and rehabilitation centres. Therefore, in order to better understand the causes of the high rates of mortality and improve the management and conservation strategies, it is important to study the species responses to environmental changes. Similar with other species, in birds, the HPA axis plays an essential role in maintaining homeostasis by producing glucocorticoids (corticosterone in birds). In this study, we sampled a total of 30 individuals humanely euthanised at the Adelaide Koala and Wildlife Centre (AKWC), and noted their clinical information. Feather samples were collected from all 30 individuals, and then were processed and analysed for corticosterone levels using enzyme-immunoassay (EIA). The biological relevance of feather CORT assay was evaluated by comparing the absolute levels of CORT between birds. We also analysed the effects of different stressors by grouped the diagnosis into acute and chronic categories. Although results suggest that stress levels were variable between the diagnosis, no statistically significant difference was found between these two categories in this study due to the limited sample size. We also obtained patient records from the 2022-2023 period from AKWC for retrospective analysis. Records were categorized and analysed based on the diagnoses, species and admission dates. Retrospective analysis suggests that in 2022, the Rainbow Lorikeet had the highest admission rate (192/544, 35.29%), followed by Magpie (124/544, 22.79%). Most admissions occurred in Summer. Musculoskeletal injury was the most prevalent diagnosis across all species with Magpies having the highest rates (73.39%) across all diagnoses and Rainbow Lorikeets the second highest (36.46%). Beak and Feather disease (BFD) was another common diagnosis for lorikeets. Data collected at 2023 followed the similar trend. This is the first study that uses non-invasive method to determine stress levels of rescued Australian native avian species, aims at improving and implementing native avian species management and conservation initiatives. This research also provides a basis for future studies which allow for more detailed analyses of wild populations and a broader range of species.

Remote Photoplethysmography (rPPG) has emerged as a non-intrusive and promising physiological sensing capability in HCI research, gradually extending its applications in health-monitoring and clinical care contexts. With advanced machine learning models, recent datasets collected in real-world conditions have gradually enhanced the performance of rPPG methods in recovering heart-rate and heart-rate variability metrics. However, the signal quality of reference ground-truth PPG data in existing datasets is by and large neglected, while poor quality references negatively influence models. Here, this work introduces a new imaging blood volume pulse (iBVP) dataset of synchronized RGB and thermal infrared videos with PPG ground-truth signals from the ear and its high resolution signal quality labels, for the first time. Participants perform rhythmic breathing, head-movement, and stress-inducing tasks, which help reflect real-world variations in psycho-physiological states. This work conducts dense (per sample) signal quality assessment to discard noisy segments of ground-truth and corresponding video frames. We further present a novel end-to-end machine learning framework, iBVPNet that features an efficient and effective spatio-temporal feature aggregation for reliable estimation of BVP signals. Finally, this work examines the feasibility of extracting BVP signals from thermal video frames, which is underexplored. The iBVP dataset and source codes are publicly available for research use.

Abstract: Ovarian cancer (OC) ranks as the fifth most common cancer among women in the United States and globally, posing a significant health threat. Reactive oxygen species (ROS) have emerged as critical factors in the pathophysiology of this malignancy. ROS, characterized by their instability due to an unpaired electron, are involved in essential cellular functions and play a crucial role in the immune response under normal physiological conditions. However, an imbalance in ROS homeostasis, leading to excessive ROS production, results in oxidative stress (OS), which can cause indiscriminate damage to cellular structures and contribute to the pathogenesis of specific diseases, including OC. OC is primarily classified based on the originating cell type into epithelial, stromal, and germinal tumors, with epithelial tumors being the most prevalent. Despite advancements in medical technology, early detection of OC remains challenging, often leading to delayed treatment initiation. Current therapeutic approaches include surgical excision of tumor tissue, radiotherapy and chemotherapy. While these treatments are effective in early-stage OC, high mortality rates and frequent relapse underscore the urgent need for novel diagnostic and therapeutic strategies. This review aims to elucidate the role of ROS in OC, emphasizing the potential for developing innovative diagnostic tools and treatments that target ROS-mediated pathways. Given the critical impact of early detection and effective treatment, advancing our understanding of ROS in the context of OC could significantly enhance patient outcomes.

In this paper, a thermodynamic investigation is done on a Kalina-flash cycle. This work is initially validated with the Kalina cycle power plant, Wich is commissioned in Husavic. Low-temperature Kalina-flash is considered for this study. This cycle is working with the ammonia-water mixture. The Kalina-flash cycle was optimized in the view of exergy and thermal efficiency. A multi-objective genetic algorithm is used to accomplish optimization. The optimum values of the objective functions are observed to be 40.20 and 11.70% respectively. At last, The influence of the separator inlet dryness fraction, basic ammonia mass fraction, temperature and flash pressure ratio on the first and second law efficiencies are analysed.

This study explored differences in student-athletes’ symptoms of depression, anxiety, and stress pre- to post-COVID-19 pandemic. The WHO reported a 25% increase in depression and anxiety rates worldwide with young people disproportionately affected. Student-athletes face many stressors related to their sporting and academic feats but what is not known is how the COVID-19 pandemic affected their experiences of mental illness. A multiple cohort cross-sectional study design was employed, and data collected using physical and online surveys. Participants (M age = 19.98 years, SD = 1.50) were recruited from UK universities (N = 807; 427 pre-pandemic cohort, 380 post-pandemic cohort). Results revealed statistically significant differences in mean depression, anxiety, and stress scores between cohorts. Scores for the post-pandemic cohort were significantly higher than pre-pandemic, suggesting a worsening of symptom severity. Distributions of student-athletes across categories of symptom severity also worsened for depressive and anxiety symptoms post-pandemic and were skewed towards more severe categories. Symptoms of de-pression, anxiety, and stress were a concern pre-pandemic. Rates are higher in the post-pandemic cohort, suggesting a worsening of symptoms. This data adds to evidence on student-athletes’ symptoms of mental illness by exploring a UK sample and comparing scores pre- and post-pandemic.

Climate change is a global issue that draws widespread attention from the international society. As an important component of the climate system, the water cycle is directly affected by climate change. Thus, it is very important to study the influences of climate change on the basin water cycle with respect to maintenance of healthy rivers, sustainable use of water resources, and sustainable socioeconomic development in the basin. In this study, by assessing the suitability of multiple General Circulation Models (GCMs) recommended by the Intergovernmental Panel on Climate Change, Statistical Downscaling Model (SDSM) and Automated Statistical Downscaling model (ASD) were used to generate future climate change scenarios. These were then used to drive distributed hydrologic models (Variable Infiltration Capacity, Soil and Water Assessment Tool) for hydrological simulation of the Yangtze River and Yellow River basins, thereby quantifying the effects of climate change on the basin water cycle. The results showed that suitability assessment adopted in this study could effectively reduce the uncertainty of GCMs, and that statistical downscaling was able to greatly improve precipitation and temperature outputs in global climate mode. Compared to a baseline period (1961–1990), projected future periods (2046–2065 and 2081–2100) had a slightly decreasing tendency of runoff in the lower reaches of the Yangtze River basin. In particular, a significant increase in runoff was observed during flood seasons in the southeast part. However, runoff of the upper Yellow River basin decreased continuously. The results provide a reference for studying climate change in major river basins of China.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

According to many research groups, high glucose induces over production of superoxide anions, and reactive oxygen species (ROS) in general is the link between high glucose levels and the toxicities seen at cellular levels. Respiratory complex anomalies could lead to the production of ROS. Calcium [Ca2+], at physiological levels serves as a second messenger in many physiological functions. Accordingly, mitochondrial calcium [Ca2+]m overload leads to ROS production which could be lethal to the mitochondria through various mechanisms. The F1F0-ATPase (ATP syn-thase or complex V) is the enzyme that is responsible for catalyzing the final step of oxidative phosphorylation. It does so by coupling the translocation of protons in the mitochondrial in-termembrane space and shuttling them to the mitochondrial matrix for ATP synthesis to take place. Mitochondrial complex V T8993G mutation specifically blocks the translocation of protons across the intermembrane space thereby blocking ATP synthesis leading to Neuropathy, Ataxia and Retinitis Pigmentosa Syndromes (NARP). This study seeks to explore the possibility of [Ca2+]m overload mediating the pathological roles of high glucose in defective respiratory chain mediated mitochondrial stress. The NARP cybrids are the in vitro experimental models for the cells with F1FO-ATPase defects, these cells harbor 98% of mtDNA T8993G mutation. Their coun-terparts 143B osteosarcoma cell lines are the parental cell lines used for comparisons. We uncov-ered that, NARP cells mediated and enhanced the death of the cells (apoptosis) when incubated with hydrogen peroxide (H2O2) and high glucose respectively as depicted by the MTT assay of cell viability. Furthermore, using the fluorescence probe-coupled laser scanning confocal imag-ing microscopy, NARP cells significantly enabled mitochondrial reactive oxygen species (mROS) formation and enhanced the depolarization of the mitochondrial membrane potential (ΔΨm). Elucidating the mechanisms of sugar enhanced toxicity on mitochondria would help in the fu-ture to alleviate the symptoms of patients associated with (NARP) syndromes.

Background: This study aimed to identify the association between occupational stress and depression-well-being by proposing a comprehensive and flexible job burden-capital model with its corresponding hypotheses. Methods: For this research, 1618 valid samples were gathered from the electronic manufacturing service industry in Hunan Province, China; self-rated questionnaires were administered to participants for data collection after obtaining their written consent. The proposed model was fitted and tested through structural equation model analysis. Results: Single-factor correlation analysis results indicated that coefficients between all items and dimensions had statistical significance. The final model demonstrated satisfactory global goodness of fit (CMIN/DF=5.37, AGFI=0.915, NNFI=0.945, IFI=0.952, RMSEA=0.052). Both the measurement and structural models showed acceptable path loadings. Job burden and capital were directly associated with depression and well-being or indirectly related to them through personality. Multi-group structural equation model analyses indicated general applicability of the proposed model to basic features of such a population. Gender, marriage and education led to differences in the relation between occupational stress and health outcomes. Conclusions: The job burden-capital model of occupational stress-depression and well-being was found to be more systematic and comprehensive than previous models.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

In the realm of high-pressure vessel simulation, conventional finite element method (FEM) approaches, as per ASME standards, may inadequately predict the behavior of flat surfaces under elevated temperatures. This study challenges the efficacy of shell-type mesh modeling for high-temperature flat plates, demonstrating that the thermal conditions within such high-pressure vessels can induce thermal instability and buckling, not accounted for by traditional FEM methods recommended by ASME. Through comprehensive analytical investigations, we reveal that traditional shell-type meshing techniques, while suitable for certain applications, fail to capture the intricate thermal stresses and deformation patterns inherent in high-temperature flat plate configurations. Our analysis delineates distinct stability regimes governed by key design parameters—including plate thickness, operating temperature, and geometric dimensions—profoundly impacting the structural integrity of heating plates under thermal loading. By elucidating these stability boundaries, this research provides engineers with critical insights necessary for optimizing the design and performance of high-temperature equipment. This includes the design of high-pressure vessels with flat surfaces for heating materials, flanges in high-temperature environments, and fins in heat exchangers across various industries such as oil and gas, pyrolysis, and power plants. The findings presented herein serve as a valuable reference for engineers seeking to comprehend and mitigate instability phenomena in solid mechanics, offering practical guidance for developing robust and reliable high-temperature structures in demanding industrial environments.

Diacylglycerol kinase (DGK) is a lipid kinase that phosphorylates diacylglycerol (DAG) to generate phosphatidic acid (PA). Based on converting one important signaling molecule (DAG) to another (PA), DGK plays an important role in plant responses to abiotic stress including waterlogging stress. However, no studies have been reported on the characterization of the DGK gene family in the waterlogging-tolerant kiwifruit germplasm, Actinidia valvata Dunn. Here, we identified 18 AvDGK genes in the A. valvata genome. The phylogenetic analysis showed that AvDGKs can be classified into three clusters, and members within the same cluster have similar domain distribution, exon-intron structures and conserved motif compositions. Chromosome localization analysis revealed that all the AvDGK genes are located across 18 different chromosomes. There were 29 duplicated gene pairs in kiwifruit and all had undergone purifying selection during evolution. Promoter cis-element analysis revealed that the cis-elements within AvDGK genes are associated with multiple functions, including phytohormone signal transduction, stress response, and plant growth and development. The expression pattern analyses indicated that AvDGK play an important role in the fruit development and plant response to waterlogging stress. AvDGKs gene family in the tetraploid A. valvata genome might promote PA synthesis and subsequent signal transduction both under short-term and long-term waterlogging stress. These results provide information regarding the structural characteristics and potential function of DGK genes within kiwifruit and lay a fundamental basis for further research into breeding for enhancing the kiwifruit’s tolerance to waterlogging stress.

The research work explores the impact of temperature on Silicon photovoltaic (PV) panels considering Nigeria as case study. It is found that high solar radiation in Nigeria increases surface temperature of PV panel above 25oC of optimal operating temperature of PV panels. Redundant energy gain from incident solar energy is dissipated at the rear of PV panels as heat, which reduces the efficiency of PV panel. Cooling mechanism is needed to cool the PV panels to increase the efficiency. In this study we demonstrated a unique design of a bifunctional photovoltaic-thermal (PVT) system by employing heat exchanger at the rear of PV panel and water is used as a working fluid that is circulated through the heat exchanger to remove the excess heat. It is observed from the simulation results that Maiduguri peak annual electrical power output gives 1907kWh/kWp which is the highest, because of high solar radiation average of 727W/m2 in a year. And for Makurdi the peak annual electrical power output of 1542kWh/kWp while for Port Harcourt the peak power output of 1355kWh/kWp respectively. Interestingly, Polycrystalline Si-PV surface temperature decrease from 49.25oC to 38.38oC. Electrical power increased from 1526.83W to 1566.82W in a day and efficiency increase from 13.99% to 15.01%.

Optical characterization and thermal aging tests are performed on a sputter-deposited coating, consisting of SiO₂/Cr₂O₃/Cr/Cr₂O₃ layers, designed and developed as a selective solar absorber to be used for unconcentrated solar thermal applications. Both measurements are performed by using a home-made apparatus, which mimics a flat plate collector under high vacuum. A Performance Criterion (PC_η(T)), based on absorber efficiency is proposed, and a forecast of service lifetime is obtained. As a result of the thermal aging tests, the selective solar absorber under study appears to be highly efficient at mid temperatures (up to 573 K) and thermally stable at temperatures (up to 690 K).

Our hypothesis that controlled ozone applications interfere into the redox balance of the biological organism (first published in 1998 with a preclinical trial on protecting the liver from CCl4 intoxication), has been verified over the last 2 decades in reactive oxygen species (ROS)-induced mitochondrial pathologies, such as rheumatoid arthritis, osteoarthritis, aging processes, diabetes-2 and in prevention of intoxications. Low-dose ozone acts as a redox bioregulator: The restoration of the disturbed redox balance is comprehensible in a number of preclinical and clinical studies by a remarkable increase of the antioxidant repair markers, here mainly shown as glutathione increase and a reduction in oxidative stress markers, mainly malondialdehyde. The mechanism of action is shown, relevant data are displayed, evaluated and comprehensively discussed: The repair side of the equilibrium increases by 21% up to 140% compared to the non-ozone treated groups and depending on the indication; the stress markers are simultaneously reduced, the redox system regains its balance.

Excretory-secretory products (ESPs) are the main research targets for investigating the hosts and helminths interaction. Parasitic worms can migrate to parasitic sites and avoid the host immune response by secreting this product. Angiostrongylus cantonensisis an important food-borne zoonotic parasite that causes severe neuropathological damage and symptoms, including eosinophilic meningitis or meningoencephalitis in humans. Benzaldehydes are organic compounds composed of a benzene ring and formyl substituents. This compound has anti-inflammatory and antioxidation properties. Previous studies showed that 3-hydroxybenzaldehyde (3-HBA) and 4-hydroxybenzaldehyde (4-HBA) can reduce apoptosis in A. cantonensis ESPs treated astrocytes. These results on the protective effect underlying benzaldehyde have primarily focused on cell survival. The study was designed to investigate the molecular mechanisms of endoplasmic reticulum stress (ER stress) and oxidative stress in astrocytes in A. cantonensis ESPs treated astrocytes and to evaluate the therapeutic consequent of 3-HBA and 4-HBA. First, we initially established the RNA-seq dataset in each group, including Normal, ESPs, ESPs+3-HBA, and ESPs+4-HBA. We also found that benzaldehyde (3-HBA and 4-HBA) can stimulate astrocytes to express ER stress-related molecules after ESP treatment. The level of oxidative stress could also be decreased in astrocytes by elevating antioxidant activity and reducing ROS generation. These results suggested that benzaldehyde may be a potential therapeutic compound for human angiostrongyliasis to support brain cell survival by inducing the expression levels of ER stress- and oxidative stress-related pathway.