This paper proposes a new cascaded three-phase multilevel inverter based on a cascaded submultilevel and single-phase H-bridge structure. The voltage source of the traditional single-phase H-bridge is replaced with the proposed cascaded submultilevel. Cascading two basic units forms the submultilevel unit. The basic and submultilevel units generate positive voltage only hence the need for an H-bridge to generate both polarities of load voltage. Five algorithms of source voltage are proposed and the optimal algorithm selected to generate the peak load voltage and output levels. The proposed three-phase cascaded multilevel inverter generates 31-level of load voltage. The per-phase component distribution of the proffered inverter are twelve power switches, four dc sources and twelve driver circuits accordingly. Principal merits of the proposed 31-level inverter are high quality load waveforms, production of high levels of load voltage utilizing reduced component quantity, simple cascaded layout, decreased inverter area, minimal inverter cost, minimum inverter losses and utilizing lower rated switches. Also, the proposed topology is highly suited for employment in PV-DVR and other power systems. To validate these advantages of the proposed multilevel inverter, contrastive analysis of the proposed inverter and existing topologies are studied. Finally, the functionality of the proposed inverter is substantiated by simulation in PSCAD/ EMTDC software.

This paper proposes a novel three-phase voltage source inverter dead-time compensation strategy for accurate compensation in wide current regions of the inverter. In particular, an analysis of the output voltage distortion of the inverter, which appears as parasitic components of the switches, has been conducted for proper voltage compensation in the low current region, and an on-line compensation voltage controller has been proposed. Also, a new trapezoidal compensation voltage implementation method using the current phase is proposed to simplify realizing the trapezoidal shape of the three-phase compensation voltages. Finally, when the proposed dead-time compensation strategy is applied, the maximum phase voltage magnitude in the linear modulation voltage regions is defined to achieve smooth operation even at high modulation index. Simulations and experiments were conducted to verify the performance of the proposed dead-time compensation scheme.

This paper focus on the modeling and time-domain analyzing method of piecewise-smooth fractional-order circuit systems. Firstly, an analytical framework is constructed based on a generalized piecewise-smooth two-port impedance network model, which takes the topological characteristics of Dickson type switched-capacitor converters (SCCs) as examples, and considers the fractional-order characteristics of class-2 X7R ceramic capacitors, which are widely used in SCCs. Secondly, the time-domain analyzing method for such a piecewise-smooth fractional-order circuit system is developed, numerical solutions are obtained, and the influence of the fractional-order capacitor on the power conversion efficiency of the system are revealed. Finally, in order to validate the analysis, both numerical simulation and experiments are provided in the work, the results of which confirm that, the proposed fractional-order analytical framework can capture the power loss mechanism of piecewise-smooth fractional-order circuit systems more effectively than the traditional integer-order based approach, thus benefiting the design of circuit systems.

This study investigates the nonlinearities in three-phase inverters for SiC-based systems and compares their performance to IGBT-based systems. An analytical model of inverter voltage distortion is developed, which accounts not only for dead time (td), switching delay time, switching frequency (fs), and voltage drops of power devices, but also for output parasitic capacitance (Cout). Experimental tests validate the model, which provides a more accurate estimate of the inverter’s output phase voltage distortion. The power device characteristics are obtained from datasheets, while Cout is determined through experimentation. Three-phase inverters with varying switching frequencies, fundamental frequencies, and dead-time values are used in simulations and experiments to determine the influence of nonlinearity on phase voltage deviation and current distortion. The results show that, due to SiC devices’ faster switching time, the phase voltage deviation and phase current distortion are lower in SiC-based inverters than in IGBT-based ones for high-frequency applications, as the dead time can be reduced.

A three-phase multilevel inverter (MLI) synthesized with 31-levels in the output voltage is used to provide ac supply to a three-phase, squirrel-cage induction motor. The gating angles required for thirty power switches in MLI are optimized by both Genetic Algorithm (GA) and Gray Wolf Op-timization (GWO). In the optimization technique, the optimal angles are determined by solving the trigonometric equations from the Fourier analysis for targeting minimum total harmonic distortion (THD) at the MLI output. Simulation model and experimental prototype are developed for performance analysis and validation. The results obtained demonstrate that the MLI is effec-tively able to produce 31-levels of three-phase ac output voltages with THD not exceeding 5% when loaded with a resistive load and a three-phase induction motor. The voltages and currents are measured and recorded for different loads and operating conditions, including the amount of energy consumed by the loads, as well as frequency analysis, which shows the absence of most of the triple harmonics that have a negative impact on the efficiency of the inverter.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

This paper presents a novel DQ-based multicarrier Pulse Width Modulation PWM for a single-phase, three-level PV-powered grid-connected F-type inverter. The main control objective in the proposed inverter is to regulate the grid current with low total harmonic distortion and load power components compensation. Despite the F-type inverter’s advanced advantages, there are only a few works addressing the control issue in the literature yet. The proposed control and switching methods aim to achieve both DC side voltage balance and lowest switching losses. The proposed scheme has been designed based on a modified multi-carrier PWM switching algorithm. Consequently, the proposed control method able to satisfy the requirements of DC side voltage balance and achieve lower switching losses. A further advantage of the proposed control and switching methods is that they retain the main advantage of the F-Type inverter, which is that only 25% of the power switches are exposed to full DC voltage. This is an important advantage since it reduces the overall cost of the inverter and improves its reliability. Overall, the proposed modified multi-carrier PWM switching algorithm appears to be a promising approach for controlling the F-Type inverter, offering improved performance and efficiency compared to other control methods. The theoretical model was verified through simulation using MATLAB/Simulink. According to the simulation results, the grid current and dc capacitor voltages are successfully managed in all operational situations.

Four-wire low voltage microgrids supply one-phase consumers with continuously changing electricity demand. For addressing climate change concerns, governments implemented incentive schemes for residential consumers, encouraging the installation of home PV panels for covering self-consumption needs. In the absence of sufficient storage capacities, the surplus is sold back by these entities, called prosumers, to the grid operator or in local markets, to other consumers. While these initiatives encourage the proliferation of green energy resources, and ample research is dedicated to local market designs for prosumer-consumer trading, the main concern of distribution network operators is the influence of power flows generated by prosumer surplus injection on the operating states of microgrids. The change in power flow amount and direction can greatly influence the economic and technical operating conditions of radial grids. This paper proposes a metaheuristic algorithm for prosumer surplus management that optimizes the power surplus injections using the automated control of three-phase inverters, with the aim of improving the active power losses and balancing the phase voltage profiles. A case study is performed on two real distribution networks with distinct layouts and load profiles and the algorithm shows its efficiency in both scenarios.

DC-connected parallel inverter systems are gaining popularity in industrial applications. However, such parallel systems generate excess current ripple (harmonics) at the DC-link due to harmonic interactions between the inverters in addition to the harmonics from the PWM switching. These DC-link harmonics cause the failure of fragile components such as DC-link capacitors. This paper proposes an interleaving scheme to minimize the current harmonics induced in the DC-link of such a system. The results show that when the carrier waves of the two inverters are phase-shifted by 90° angle, the maximum high-frequency harmonic ripple cancellation occurs, which reduces the overall RMS value of the DC-capacitor current.The outcome of this proposed solution is a cost-effective DC-harmonics mitigating strategy for the industrial designers to practically configuring multi-inverter systems, even when most of the drives are not operating at rated power levels. Experimental and simulation results presented in this paper verify the effectiveness of the proposed carrier-based phase-shifting scheme for two different configurations of common DC connected multi-converter systems.

Zinc oxide (ZnO) nanostructures have been studied extensively in the past years due to the novel electronic, photonic, mechanical and electrochemical properties. Recently, more attention has been paid to assemble nanoscale building blocks into three dimensional (3D) complex hierarchical structures, which not only inherit the excellent properties of the single building blocks but also provide potential applications in the bottom-up fabrication of functional devices. This review article focuses on 3D ZnO hierarchical nanostructures, and summarizes major advances in the solution phase synthesis, applications in environment, and electrical/electrochemical devices. We present the principles and growth mechanisms of ZnO nanostructures via different solution methods, with an emphasis on rational control of the morphology and assembly. We then discuss the applications of 3D ZnO hierarchical nanostructures in photocatalysis, field emission, electrochemical sensor, and lithium ion batteries. Throughout the discussion, the relationship between the device performance and the microstructures of 3D ZnO hierarchical nanostructures will be highlighted. This review concludes with a personal perspective on the current challenges and future researches.

Adjustable frequency converters are widely used in modern automated asynchronous drives due to their high efficiency and high responsiveness control strategies. Control algorithms for frequency converters are divided into two main groups: constant frequency commutation and random frequency commutation. Research results on various commutation frequencies, conducted using Matlab/Simulink software, show that the use of random frequency commutation provides better efficiency by significantly reducing the amplitude of harmonic oscillations at different frequencies, with a reduction in switching losses in transistors. Currently, a converter with random frequency commutation is being researched and applied in the direct torque control system. The traditional direct control system, based on a two-level inverter, is widely used due to its simplicity and ease of implementation. However, this method results in the output current of the two-level converter, supplied to the motor stator, having many harmonic distortions, leading to strong torque fluctuations regardless of the rotation speed and ultimately causing additional losses in the stator windings and reducing the motor's lifespan. To enhance the efficiency of automated asynchronous drives, this article presents an algorithm for a direct control system based on a three-level NPC inverter using a PI speed regulator. The proposed algorithm's research is validated in the Matlab/Simulink environment. The research results show that in the absence of harmonic filtering, the stator current harmonic distortion coefficient is approximately 11%, and torque fluctuations are less than 5% of the resistive torque. The fluctuations between the two capacitors remain almost unchanged throughout the entire process.

In large-capacity energy storage systems, instructions are decomposed typically using an equalized power distribution strategy, where clusters/modules operate at the same power and durations. When dispatching shifts from stable single conditions to intricate coupled conditions, this distribution strategy inevitably results in increased inconsistency and hastened system aging. This paper presents a novel differentiated power distribution strategy comprising three control variables: the rotation status, the operating boundaries for both Depth of Discharge (DOD) and C-rates (C) within a control period. The proposed strategy integrates an aging cost prediction model developed to express the mapping relationship between these control variables and aging costs. Additionally, it incorporates the multi-colony particle swarm optimization (Mc-PSO) algorithm into the optimization model to minimize aging costs. The aging cost prediction model consists of three functions: predicting health features (HFs) based on the cumulative charge/discharge throughput quantity and operating boundaries, characterizing HFs as comprehensive scores, and calculating aging costs using both comprehensive scores and residual equipment value. Further, we elaborated on the engineering application process for the proposed control strategy. In the simulation scenarios, this strategy prolonged the service life by 14.62%, reduced the overall aging cost by 6.61%, and improved module consistency by 21.98%, compared with the traditional equalized distribution strategy. In summary, the proposed strategy proves effective in elongating service life, reducing overall aging costs, and increasing the benefit of energy storage systems in particular application scenarios.

With the development of the photovoltaic industry, there will be an increasing demand for efficient, high-power density, and low-cost grid interface converters. Compared with two-level inverters, multilevel inverters have the following advantages: (1) lower device voltage ratings; (2) better output filtering spectrum; (3) lower electromagnetic interference (EMI) noise; and (4) higher switching speed capability. However, the complex switching circuit of the multilevel inverter will bring more parasitic inductance, resulting in more serious switching overvoltage (ringing). Consider that commonly used overvoltage absorption schemes are effective only for overvoltage or sup-pression of oscillations. Therefore, a new overvoltage absorption circuit is proposed in this paper, which can not only alleviate the overvoltage and ringing phenomena but also suppress the effect of voltage jumps during low-frequency switching on high-frequency input voltage. This overvoltage absorption circuit is characterized by low overvoltage, fast ringing damping, and minimum ca-pacitance. Experiments and simulations are conducted to verify the effectiveness of this overvoltage absorption circuit using a three-level ANPC inverter as a prototype. The results show that the proposed overvoltage absorption circuit can significantly reduce the overvoltage level, shorten the oscillation time, and reduce the voltage difference between the upper and lower DC bus capacitors.

Because imbalanced power will cause the loss of the propulsion motor of the railway vehicle, and the increase in temperature will shorten the service life of the electric vehicle. Not only this, but also increase the cost of electricity and maintenance. In the past, the industry only focused on methods to improve power quality such as load capacity, relay setting, and harmonic resolution. Now, the consider of three-phase unbalance rate (TPUR) must be applied. I propose special transformers wiring (STW) to improve the three unbalance rates and provide different transformer wiring methods. According to the IEEE Committee, in the future, power companies will need to install balanced relay stations to improve three-phase unbalance rate. the internal regulations of Taipower must be less than 4.5% (voltage unbalance rate (NPSUR)of 2.5% and motor temperature rise of 12.5%). the derivation of the transformer "three-phase unbalance rate" model is the focus of the railway system. This research is based on the model derivation of different wiring methods to improve the hot problem caused by the three-phase imbalance and improve the service life of the train. And pointed out that Scott, Le-Blanc, Modified-Woodbridge three wiring methods can be applied to future railway system routes to improve the three-phase unbalance rate, in line with the IEEE standard of less than 2%.

The theory and working principle of fabric phase sorptive extraction (FPSE) is presented that eloquently explains the mystery behind this new and powerful sample preparation technique. FPSE innovatively integrates the benefits of sol-gel coating technology and the rich surface chemistry of cellulose/polyester/fiberglass fabric, resulting in a microextraction device with very high sorbent loading in the form of an ultra-thin coating. This porous sorbent coating and the permeable substrate synergistically facilitate very fast extraction equilibrium. The flexibility of the FPSE device allows for direct insertion into original, unmodified samples of different origin. Strong chemical bonding between the sol-gel sorbent and the fabric substrate permits the exposure of FPSE devices to any organic solvent for analyte back-extraction/elution and to highly acidic or basic environments (pH 1-12) if required. A sol-gel derived sorbent, highly polar sol-gel poly(ethylene glycol) coating, was generated on cellulose substrates. Five cm2 segments of these coated fabrics were used as the FPSE devices for sample preparation using direct immersion. An important class of environmental pollutants, substituted phenols, was used as model compounds to evaluate the extraction performance of FPSE. The high primary contact surface area (PCSA) of the FPSE device and porous structure of the sol-gel coatings resulted in very high sample capacities and incredible extraction sensitivities for both the compound classes in a relatively short period of time. Different extraction parameters were evaluated and optimized. The new extraction devices demonstrated part per trillion level detection limits for substituted phenols, a wide range of detection linearity, and good performance reproducibility.

Linear state estimation (SE) formulation under a rectangular coordinate system has been proved to be applicable for real-time distribution network management. Micro phasor measurements’ model can be accommodated into this kind of SE easily. However, voltage magnitude, active power and reactive power measurements are transformed to linear measurements with large node voltage error. To cope with this issue, a linear state estimation under a polar coordinate system is adopted at the first stage to obtain accurate enough complex node voltage, and then nonlinear measurements are transformed to be linear with complex node voltage. At the second stage, linear SE under a rectangular coordinate system can be adopted to satisfy more strict network constraints. The proposed two-stage linear SE is validated on balanced 14, 33, 70,84, 119, 135 nodes network and IEEE 13, 34, 37,123 unbalanced test feeders.

With large-scale distributed generators (DGs) in an active distribution network (ADN), conventional load flow convergence failure is incurred by heavy power transmission. The Holomorphic Embedding Load Flow Method (HELM) has proven to be more robust than the Newton–Raphson method under heavy power transmission. At present, HELM is mainly designed for balanced transmission networks. In this study, we developed a three-phase HELM model to accommodate DGs, delta connection loads, and ZIP loads for ADN. The effectiveness and better performance of the proposed method under heavy load situations were validated using modified unbalanced IEEE 13, 34, 37, and 123 test feeders.

Carotid atherosclerotic lesions are a major cause of cerebrovascular disease (CVD). Identification and quantification of carotid plaques are important for categorizing the vulnerability of plaques for rupture and assessing the impact of treatments. The irregularity of plaque surface is associated with previous plaque rupture and plays an important role in the risk of stroke. Thus, the aim of this study is to develop and validate novel vulnerability biomarkers from three-dimensional ultrasound (3DUS) images by analyzing the surface morphological characterization of carotid plaque using fractal geometry features. 3D box-counting and 3D blanket are the two types of 3D fractal dimension that were employed to describe the smoothness of plaques. This fractal dimension analysis tool was used to evaluate the effect of atorvastatin using 3DUS carotid images, which were acquired from 6 patients treated with atorvastatin with 80 mg daily and 5 patients with placebo. The Student's T Test results showed that those two fractal features were effective for detecting the statin-related changes in carotid atherosclerosis with p<0.0068 and p<0.015 respectively, suggesting that 3D fractal dimension measurements can be used effectively to analyze the surface characteristics of carotid plaques, especially for evaluating the impact of the treatment.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

The purpose of this paper is to study the influence of diffusion and thermal loading due to pulsed laser heating on a thermoelastic solid with voids in the context of the model of three-phase-lag. The non-dimensional governing equations are formulated and then the exact expressions for the temperature field, the displacement components, the stress components, the concentration field and the change in the volume fraction field are obtained using the normal mode technique. The material is an isotropic, homogeneous elastic half-space and heated by a non-Gaussian laser beam with pulse duration of ps. The magnesium crystal element is used as an application to compare the predictions induced by diffusion and laser pulse on poro-thermoelastic medium of the model of three-phase-lag with those for the theory of Green–Naghdi of type III. The results obtained for thermal changes are verified by comparison with two theories of thermoelasticity, namely the model of three-phase lag (3PHL) and the Green and Nagdi type III theory. Plot the expressions to examine the effect of the laser pulse at two different values of time and the effect void parameter. This study also yields some interesting special cases.

The discrete element method (DEM) coupled with computational dynamics (CFD) has been considered one of the most sensitive ways of studying fluidized beds. This paper presents gas-solid fluidized bed simulations by use of CFD-DEM. The two-phase interaction is calculated in a way of decoupling. Within the effective neighborhood of the particles, the kernel approximation method is used to calculate the local porosity, thereby calculating the drag force on the particles. At the grid scale, the momentum exchange coefficient is calculated using a two fluid model based method, thereby calculating the source term of the phase interaction in the fluid control equation. The simulated form, size and motion process of the big bubble are all consistent with experimental observations. The simulated solid volume fraction and relative pressure averaged in a horizontal plane at 45 mm above the bottom are in reasonable agreement with the experimental data. The fluctuation of the simulated bed height over time is similar to the experimental measurement results. The reproduction of these qualitative and quantitative results indicates that the proposed method effectively improves simulation performance and accuracy.

This paper presents a symmetrical topology for the design of solid-state transformer, made up of power switching converters, to replace conventional bulky transformers. The proposed circuitry not only reduces the overall size but also provides power flow control with the ability to be interfaced with renewable energy resources (RESs) to fulfill the future grid requirements at consumer end. Solid state transformer provides bidirectional power flow with variable voltage and frequency operation and has the ability to maintain unity power factor, and current total harmonic distortion (THD) for any type of load within defined limits of IEEE standard. Solid State Transformer offers much smaller size as compared to that of the conventional iron core transformer. MATLAB/Simulink platform is adopted to test the validity of the proposed circuit for different scenarios by providing the simulation results evaluated at 25 kHz switching frequency.

The behaviour and bifurcations of solutions to three-dimensional (three-phase) quadratic polynomial dynamical systems (DSs) are considered. The integrability in elementary functions is proved for a class of autonomous polynomial DSs. The occurrence of bifurcations of the type twisted fold is discovered on the basis and within the frames of the elements of the developed DS qualitative theory. The discriminant criterion applied originally to two-phase quadratic polynomial DSs is extended to three-phase DSs investigated in terms of their coefficient matrices. Specific classes of D- and S-vectors are introduced and complete description of the symmetry relations inherent to the DS coefficient matrices is performed using the discriminant criterion.

The notion of the three-phase (line) tension remains one of the most disputable notions in the surface science. A very broad range of its values has been reported. Experts even do not agree on the sign of the line tension. The polymer-chain-like model of the three-phase (triple) line enables the rough estimation of the entropic input into the value of the line tension, estimated as Γ_en≅(k_B T)/d_m ≅〖10〗^(-11) N, where d_m is the diameter of the liquid molecule. The introducing of the polymer-chain-like model of the triple line is justified by the “water string” model of the liquid state, predicting strong orientation effects for liquid molecules located in the vicinity of hydrophobic moieties. The estimated value of the entropic input into the line tension is close to experimental findings, reported by various groups.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

In steel recycling, the optimization of electric arc furnaces (EAFs) is of central importance in order to increase efficiency and reduce costs. This study focuses on the optimization of electric arcs, which make a significant contribution to the energy consumption of EAFs. A three-phase equivalent circuit integrated with the Cassie-Mayr arc model is used to capture the nonlinear and dynamic characteristics of arcs, including arc breakage and ignition process. A particle swarm optimization technique is applied to real EAF data containing current and voltage measurements to estimate the parameters of the Cassie-Mayr model. A novel Arc Quality Index (AQI) is introduced in the study, which can be used to evaluate arc quality based on deviations from optimal conditions. The AQI provides a qualitative assessment of arc quality, analogous to indices such as arc coverage and arc stability. The study concludes that the AQI serves as an effective operational tool for EAF operators to optimize production and increase the efficiency and sustainability of steel production. The results underline the importance of understanding electric arc dynamics for the development of EAF technology.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

This research focuses on the Hopf bifurcation occurring at a singular point with high-order degeneracy in a class of three-dimensional systems. Based on center manifold theorem, by expanding the technique for determining singular point values of degenerate singularities in two-dimensional systems, the formal series method to determine the singular point values at the high-order degenerate critical point is discussed. Furthermore, a class of specific three-dimensional differential systems with high-order degenerate singularities is explored. By computing the singular point values and determining center conditions, we proved that a minimum of 5 small-amplitude limit cycles in the vicinity of the origin. This research provides new perspectives on the center problem and limit cycle bifurcation in high-dimensional systems with high-order degenerate singular points.

Three-phase motors are commonly adopted in several industrial contexts and their failures can result in costly downtime causing undesired service outages; this way, motor diagnostics is an issue that assumes great importance. To prevent their failures and timely face the considered service outages, a non-invasive method to identify electrical and mechanical faults in three-phase asynchronous electric motors is proposed in the paper. In particular, a measurement strategy along with a machine learning algorithm based on Artificial Neural Network is exploited to properly classify failures. In particular, digitized current samples of each motor phase are first processed by means of FFT and PSD in order to estimate the associated spectrum. Suitable features (in terms of frequency and amplitude of the spectral components) are then singled out to either train or feed a neural network acting as a classifier. The method is preliminary validated on a set of 28 electric motors, and its performance is compared with common state-of-art machine learning techniques. The obtained results show that the proposed methodology is able to reach accuracy levels greater than 98\% in identifying anomalous conditions of three-phase asynchronous motors.

The AREB/ABF (ABA response element binding) proteins in plants are vital for plant stress responses, but the understanding of AREB/ABFs in orchid species, an important traditional medicinal and ornamental plants, is limited. Here, twelve AREB/ABF genes were identified within three orchids’ complete genome and classified into three groups (groups I, II, and III) via a phylogenetic analysis, which was further supported by the analysis of their conserved motifs and gene structures. The cis-elements analysis showed that hormone response elements followed by light and stress responses were widely rich in AREB/ABFs. A prediction analysis of orchid ABRE/ABF-mediated regulatory network was further constructed through cis-regulatory elements (CREs) analysis of their promoter regions and revealed that several transcriptional factor (TF) gene family were abundant as the potential regulators for orchid AREB/ABFs. Expression profile analysis based on public transcriptomic data showed that most AREB/ABF genes have distinct tissue-specific expression patterns in orchid plants. Additionally, DcaABI5 as the homolog of ABA INSENSITIVE 5 (ABI5) from Arabidopsis was selected for further analysis. The results showed that Arabidopsis transgenic overexpressing DcaABI5 could rescue the ABA insensitive phenotype in the mutant abi5. Collectively, these findings will provide valuable information on AREB/ABF genes in orchids.

The main objective of this study was to compare the removal efficiency of nutrients using Lactuca sativa, Medicago sativa and Phragmites australis in subsurface flow constructed wetlands with horizontal flow. In order to test water quality, fabricated reactors designed and the plants cultivated in the soil while their root were inside the wastewater. A long time study carried out from spring till end of autumn (9 months) in order to evaluate the difference in removal rate based on the seasonal changes. The highest removal rate was during summer which followed by spring and autumn. Thus, the effect of plants on the removal efficiency of organic matter (COD, BOD), TSS and nutrient (P and TN) appeared to be dependent on the seasonal growth. Phragmites australis the most sensitive species in order the removal of nutrient from wastewater.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

Epilepsy is a common neurological condition, typically diagnosed using Electroencephalogram (EEG). Large scale EEG datasets have recently been made publicly available, allowing the use of advanced Machine Learning (ML) algorithms to analyze EEG patterns associated with epilepsy. While most existing studies focus on identifying seizures in the EEG, few have tried to identify preictal EEG segments. Identifying preictal EEG segments are not only useful in developing early warning systems but also helps inform the course of treatment for the patient. In this study, we propose to represent EEG segments as images, instead of time-series data, and identify preictal EEG segments using a preexisting ML algorithm (YOLOv8) designed for image processing. Multiplexed images (containing the original EEG signal represented on a 2D grid, kurtosis, and spectral entropy) achieve the best accuracy of 95.75% on the dataset while images just containing the EEG signal result in an accuracy of 91.25%. Using only spectrograms, generated from the original EEG signal, results in an accuracy of 90.15%.

A power factor correction (PFC) rectifier is compulsory for any electronic circuitry connected to the electrical grid. The majority of PFCs that are utilized are based on a step-up converter that supplies high DC voltage at its output terminal. Electric vehicle battery voltage varies from a few hundred to almost a thousand volts. Thus, an additional conversion step is obligatory when designing an all-brand universal charger. This paper presents a new type of front-end versatile step up / down three voltage level PFC. The rectifier can operate in continuous conduction mode or discontinuous conduction mode. First, the rectifier’s principle of operation is described, and then an innovative rectifier is analyzed for continuous and discontinuous conduction modes. Finally, the proposed theory is experimentally validated in a multiplier-less dual loop mode at discontinuous conduction modes. It was shown that although there is no multiplier use in the control circuitry, the power factor is near unity. It was revealed that the rectifier could swing the output voltage from 50 V to 900 V while the input voltage was 230 Vrms. The innovative topology suits any standard PFC rectifier, three-level voltage supplement, and dual-stage low-voltage power supply.

The past two decades has seen a growing demand for high-power, high-voltage utility scale inverters mostly fueled by the integration of large solar PV and wind farms. Multilevel inverters have emerged as the industry choice for these megawatt range inverters because their reduced voltage stress, capable of generating an almost sinusoidal voltage, in-built redundancy, among others. This paper present a new Switched-Source Multilevel Inverter (SS MLI) architecture. The new inverter show superior over existing topologies. It has reduced voltage stress on the semiconductor, uses less number of switches –reduced size/weight/cost and increased efficiency. The new SSMLI is comprised of two voltage sources (V₁, V₂) and 6 switches. It is capable of generating 5-level output voltage in symmetric modes (i.e., V₁ = V₂), and 7-level output voltage in asymmetric modes (i.e., V₁ ≠ V₂). To demonstrate the validity of the proposed inverter, simulations results using MATLAB^® /Simulink^® for 5- and 7-level output voltages are presented . The simulations are also verified experimentally using a laboratory prototype.

The three-phase separator was perforated after four years’ service. The perforation position is at the bottom of the vessel under the baffle plate in an oil transfer station. The cause of perforation was investigated by chemical analysis using a direct-reading spectrometer, microstructure examined by optical microscope(OM), and lab simulated corrosion experiments by electrochemical workstation, and the corrosion products examined with scanning electron microscopy(SEM), energy dispersive spectrometer(EDS) in this paper. The analyses indicated that the coating at the base of the pressure vessel failed and this led to the direct exposure of the carbon steel plate to the corrosive medium. The electrical contact between the carbon steel and the stainless steel, sets up a galvanic cell that accelerated the corrosion of the pressure vessel which eventually led leads to the perforation.

Structural vibration induced by dynamic load or natural vibration is a nonnegligible factor in failure analysis. Based on vibrating boundary condition, impact resistance of shape memory alloy reinforced composites is investigated. In this investigation, modified Hashin’s failure criterion, Brinson’s model and visco-hyperelastic model are implemented into the numerical model to charactering the mechanical behavior of glass fiber/epoxy resin laminates, SMAs and interphase, respectively. First, fixed boundary condition is maintained in simulation to verify the accuracy of material parameters and procedures by comparing with experimental data. Then, a series of vibrating boundaries with different frequencies and amplitudes are applied during the simulation process to reveals the effect on impact resistances. The statistics of absorbed energy and contact force indicate that impact resistance of the composite under high frequency and large amplitude is lower than that under low frequency and small amplitude, and summarized by a mathematical expression.

This paper proposed a three-layer distributed simulation network architecture: 1. Distributed virtual simulation network, 2. Perception and control sub-network, and 3. Collaborative communication service network. This simulation architecture runs on a distributed platform. The platform can provide a unique virtual scenario and several simulation services to verify the individual robot system's basic perception, control, and planning algorithms and the distributed collaborative algorithms of heterogeneous multi-robot systems. Furthermore, we designed a simulation experiment scenario for classical heterogeneous robot systems such as unmanned aerial vehicles (UAVs) and unmanned ground vehicles (UGVs). At last, We gave a rough estimation model of the bandwidth.

To enhance the applicability of dual-phase high-entropy alloys (HEAs) like Fe32Cr33Ni29Al3Ti3, fabricated via selective laser melting (SLM), a focus on improving their mechanical properties is essential. As part of this effort, heat treatment was explored. This study compares the microstructure and mechanical properties of the as-printed sample with those cooled in water after undergoing heat treatment at temperatures ranging from 1000 to 1200 ℃ for 1 hour. Both pre- and post-treatment samples reveal a dual-phase microstructure comprising FCC and BCC phases. Although heat treatment led to a reduction in tensile and yield strength, it significantly increased ductility compared to the as-printed sample. This strength-ductility trade-off is related to changes in grain sizes with ultrafine grains enhancing strength and micron grains optimizing ductility, also the influence of the content of FCC/BCC phases and dislocation density. In particular, the sample heat-treated at 1000 °C for 1 hour and then water-cooled exhibited a better combination of strength and ductility, a yield strength of 790 MPa, and an elongation of 13%. This research offers innovative perspectives on crafting dual-phase HEA of Fe32Cr33Ni29Al3Ti3, allowing for tailorable microstructure and mechanical properties through a synergistic approach involving SLM and heat treatment.

To build a stable power factor and high output accuracy, it should use balanced active and reactive power, also used ultrasonic PWM was used with the frequencies (20–500 kHz). I also used a three-phase dynamic load at the output system and was connected to the compound splicing (CS) system this is a novelty. An oscillator circuit with 4Ghz as a microcontroller is a novelty, and designing ADC is utilized to increase accuracy, as well as contribute to the reduction of loss brought on by the characteristics of voltage source inverters (VSI), such as dead time determined by the excess voltage or voltage drop in the inverter, circumstances abnormal to the load current, such as short circuit current in the production phase, and so forth. The innovation relates to the inverter's load sensing circuit, current smoothing during operation, reaction, spontaneous power factor enhancement of the inverter, and correction of reactive power of passive devices. This invention contributes to the advancement of D.C to A.C power converter by the achievement of extremely low losses, excellent precision, and lightweight construction. Additionally, the accuracy ranges from 99%, and the total harmonic distortion (THD) of the voltage and current is (0.1%-0.8%). We Power MOSFET are used, along with FPGA to improve control over the creation of ultrasonic PWM signals, the programmable peripheral interface (PPI) 8255A for regulatory work. The marks serve as proof of this.

In this research paper, a high gain transformer less inverter modeling which is used for the smart grid technology or as the stand alone for home appliances is proposed. The proposed transformer less topology provides a higher voltage gain, low cost, small size and simple control stand alone transformer less inverter for home appliances. The above inverter is modeled by using software which is known as MATLAB/ Simulimk.

Air conditioning system of electric vehicles has new change as the internal combustion engine is being replaced with electrified AC motor. With large amount of batteries installed at the bottom of frame, the conventional compressor which is belt-driven can be removed and another AC motor can play the role for air conditioning in electric vehicles. From this change, the system efficiency would be improved since it is possible to control the electrified compressor independently from traction system in contrast with the belt-driven compressor. As a result, by applying the electrified compressor for air conditioning system, the whole system can achieve better efficiency and longer driving distance, which is most important in electric vehicles. In this paper, 3-phase interior permanent magnet synchronous motor (IPMSM) was designed using lumped-parameter model and finite element method.

High-penetration of Distributed Energy Resources (DER) in low voltage distribution grids, mainly photovoltaics (PV), might lead to overvoltage in the point of common coupling. Volt-VAr is one of the common control functions for DER power converters used to enhance the stability and the reliability of the voltage in the distribution system and, thus, fulfilling the network operator requirements. In this study, a centralized algorithm will provide local Volt-VAr control parameters to each PV inverter, based on the electrical grid characteristics where each equipment is installed. Since accurate information of grid characteristics is typically not available, the parametrization of the electrical grid is done using power meter data in DER location and a voltage sensitivity matrix. The algorithm has different optimization modes to both minimize voltage deviation and line current. In order to validate the effectiveness of the algorithm and its deployment in real infrastructure, it has been tested in an experimental setup with PV emulators in a set of 5-day tests. Volt-VAr control algorithm successfully adapted its parameters based on grid topology and PV inverter characteristics, achieving a voltage reduction up to 25% of the allowed voltage deviation.

A hybrid material, consisting of commercially available nitrocellulose (NC) membrane non-covalently modified with amino-polyethylene glycol functionalized reduced graphene oxide (NH2-PEG-rGO) nanoparticles, was successfully synthesized for oligonucleotide extraction. Fourier Transform Infrared Spectroscopy (FTIR) confirmed the modification of the NC membrane, revealing characteristic peaks of both compounds NC and NH2-PEG-rGO. Scanning Electron Microscopy (SEM) exhibited morphological changes in the NC/NH2-PEG-rGO hybrid membrane, marked by the introduction of NH2-PEG-rGO particles, resulting in a distinctly smothered surface compared to the porous surface of the NC control membrane. Wettability assays revealed hydrophobic behavior for the NC/NH2-PEG-rGO hybrid membrane, with a water contact angle exceeding 90°, contrasting with the hydrophilic behavior characterized by a 16.7° contact angle in the NC membrane. The performance of the NC/NH2-PEG-rGO hybrid membrane was evaluated for the extraction of ssDNA with fewer than 50 nucleotides from solutions containing various ionic species (MnCl2, MgCl2, and MnCl2/MgCl2). The NC/NH2-PEG-rGO hybrid membrane exhibited optimal performance when incubated in MgCl2, presenting the highest fluorescence emission at 525 relative fluorescence units (r.f.u.). This corresponds to the extraction of approximately 610 pg (≈13%) of the total oligo-DNA, underscoring the efficacy of the pristine material, which extracts 286 pg (≈6%) of oligo-DNA in complex solutions.

Considering the fault "N-1" checksum and the power flow, the single-phase power flow model is further transformed into a three-phase power flow model, and the asymmetry of the three-phase power flow is measured by the three-phase unbalance factor. The calculation model is linearized by the second-order cone relaxation and the Big-M method. At the same time, the load response and distribution network reconstruction are used to improve the reliability of the power supply network to cope with the power failure. The relationship between power supply capability and power flow constraints, main transformer capacity and distributed power parameters is analyzed by IEEE 33-node three-phase power distribution system. The feasibility of the proposed model and the accuracy of the second-order cone relaxation are verified by numerical examples, which provides a technical reference for distribution network planning.

In this paper, intrusion detection systems are thoroughly investigated utilizing the CSE-CIC-IDS-2018 dataset. The research is divided into three key phases: first, applying Data Cleaning, Exploratory Data Analysis, and Data Normalization techniques (min-max and z-score) for preparing data across distinct classifiers. Second, feature importance is reduced using a combination of Principal Component Analysis (PCA) and Random Forest (RF), with the goal of improving processing speed and decreasing model complexity. This stage comprises a comparison with the entire dataset. Finally, machine learning algorithms (XGBoost, CART, DT, KNN, MLP, RF, LR, and Bayes) are applied to specific features and preprocessing approaches. Surprisingly, the XGBoost, DT, and RF models outperform in both ROC values and CPU runtime. Following evaluation, which includes PCA and RF feature selection, an optimal set is produced.

A modular approach to the construction of electric machines, drive systems, power supply systems is a new direction of modern technology development. Especially, the modular approach is promising for electric vehicles due to such positive aspects as increased efficiency, fault tolerance, overall reliability, safety, enhanced control capabilities, etc. In this work, the modular approach is comprehensively applied to an EV powertrain system, which includes a dual three-phase (DTP) BLDC motor with two machine modules of an asymmetric configuration, two battery modules and a supercapacitor module (SCM). The proposed H–H configuration of modular EV powertrain system includes four voltage source inverters that combine the power modules with the open ends of the windings (OEW) of the module machine armature, and provide control of their operation. Based on the developed mode system of the OEW machine module operation for EV traction and braking, a general control algorithm for the proposed configuration of the modular EV powertrain system has been developed. It combines the control of the operating modes with the functions of maintaining the required SOC level of the SCM and equalizing the SOCs of the two battery modules. The conducted simulation and experimental studies confirmed the workability and effectiveness of the proposed solutions.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

The fitting and modeling of skewed, complex, symmetric, and asymmetric datasets is an exciting research topic in many fields of applied sciences, notably lifetime, medical, and financial sciences. The Heavy tailed Nadarajah Haghighi model is introduced by compounding the heavy tailed family and Nadarajah Haghighi distribution in this paper. The so obtained model has three parameters accounting for the scale and shape of the distribution. The proposed distribution's fundamental characteristics such as probability density, cumulative distribution, hazard rate, and survival functions are provided, and several key statistical properties are established, and several entropy information measures are proposed. The estimation of model parameter is performed via the ML procedure. Further, different simulation experiments are conducted to demonstrate the performance of proposed estimator’s using some measure, like the average estimate, the average bias, and associated mean square error. Finally, we are applied our proposed model to analyze three different real datasets. In our illustration, we are compared the practicality of the recommended model with several well-known competing models.

We report neutralization titer data against contemporary SARS-CoV-2 sublineages from an ongoing, open-label, phase 2/3 trial of a single 30-μg dose of monovalent Omicron XBB.1.5-adapted BNT162b2 vaccine. Healthy participants had previously received ≥3 doses of a US-authorized mRNA vaccine, with the most recent being a bivalent Omicron BA.4/BA.5-adapted vaccine administered ≥150 days before study vaccination. In this analysis, Omicron XBB.1.5, BA.2.86, and JN.1 serum neutralizing titers were assessed at baseline and 1 month after vaccination in a subset of ≥18-year-olds (N = 40) with evidence of previous SARS-CoV-2 infection. Immunogenicity was also evaluated in a demographically matched group of participants who received bivalent BA.4/BA.5-adapted BNT162b2 in another study (ClinicalTrials.gov Identifier: NCT05472038). The XBB.1.5-adapted BNT162b2 vaccine elicited higher XBB.1.5, BA.2.86, and JN.1 neutralizing titers than those elicited by bivalent BA.4/BA.5-adapted BNT162b2. Overall geometric mean fold rises in neutralizing titers from baseline to 1 month after vaccination were higher among participants who received XBB.1.5-adapted BNT162b2 than those who received bivalent BA.4/BA.5-adapted BNT162b2 for XBB.1.5 (7.6 vs 5.6), slightly higher for JN.1 (3.9 vs 3.5), and similar for BA.2.86 (4.8 vs 4.9). ClinicalTrials.gov Identifier: NCT05997290.

The search of DNA polymorphisms useful for the genetic improvement of dairy farm animals lasts more than 40 years with relevant findings in cattle for milk traits, where the best combination of alleles for dairy processing have been found in casein genes and in the DGAT1. Nowadays, similar results are not reached yet in river buffaloes despite advanced genomic technologies and accurate phenotype records are available. The aim of the present study was to investigate and validate in a larger buffalo population the effect on six milk traits of four single nucleotide polymorphisms (SNP) in the CSN1S1, CSN3, SCD and LPL genes, previously reported to be associated with or affect dairy traits in smaller populations often belonging to one farm. A total of 800 buffaloes were genotyped. Daily milk yield (dMY, kg), protein yield (dPY, kg) and fat yields (dFY, kg), fat and protein contents (dFP, % and dPP, %), somatic cell count (SCC, 103cell/ml) and urea (mg/dl) were individually recorded in each month for the whole lactation from 2010 to 2021. A total of 15,742 individual milk test day records (2,496 lactations) were available on 680 buffalo cows with 3.6±1.7 parity (from 1 to 13) and 6.1±1.2 test day records per lactation on average. Three out four SNP in CSN1S1, CSN3 and LPL were associated with at least one of analyzed traits. In particular, the CSN1S1 (AJ005430:c.578C&gt;T) gave favorable associations with all yield traits (dMY, p=0.022; dPY, p=0.014 ; dFY, p=0.029) and SCS (p=0.032), whereas the CSN3 (HQ677596: c.536C&gt;T) positively associated with SCS (p=0.005) and milk urea (p=0.04). Favorable effect on dMY (p=0.028), dFP (p=0.027) and dPP (p=0.050) were observed for the LPL. Conversely, SCD did not show any association with milk traits. This is the first example of confirmation study carried out in the Mediterranean river buffalo for genes of economic interest in dairy field and it represents a very important indication for the preselection of young bulls destined to breeding programs in the view of a more sustainable dairy production.

Permanent magnet brushless DC motor (BLDCM) is usually controlled by six step commutation method, and flux-weakening method is used to make the motor run higher above the base speed. For now, it is considered that the weak magneto-electric angle range is 0-pi/3, and that of deep weakening is pi/3-pi/2. In the field- weakening control, the forward shift of commutation point will form inverter circulating current in the three-phase bridge of inverter and the stator winding of the motor. In this paper, the principle of inverter circulating current formed by inverter is analyzed. Through magnetic potential analysis and Simulink simulation, it is concluded that flux-weakening control will generate inverter circulating current in the inverter and motor stator winding. The inverter circulating current affects the magnetic potential of motor, and magnetic potential will move to the rotating direction of motor rotor. When the forward shift angle of inverter commutation point is 0-pi/6 electrical angle, the movement amplitude of current circulating current of inverter is less than pi/6, which plays the role of weakening magnetic field and driving effect; when the forward moving angle is pi/6-pi/3, the movement amplitude of inverter circulating current exceeds pi/6, which plays the role of magnetic weakening and braking. When the braking effect occurs, the reverse torque will appear, resulting in the decrease of motor torque and efficiency. Therefore, the range of weak magneto-electric angle should be between 0-pi/6.

The total ionizing dose (TID) effect significantly impacts the electrical parameters of fully depleted silicon on insulator (FDSOI) devices and even invalidates the on-off function of devices. At present, most of the irradiation research on the circuit level is focused on the single event effect, and the research on the total ionizing dose effect is very little. Therefore, this study mainly analyzes the influence of TID effects on a CMOS inverter circuit based on 22 nm FDSOI transistors. First, we constructed and calibrated an N-type FDSOI metal-oxide semiconductor (NMOS) structure and P-type FDSOI metal-oxide semiconductor (PMOS) structure. The transfer characteristics and trapped charge distribution of these devices were studied under different irradiation doses. Next, we studied the TID effect on an inverter circuit composed of these two MOS transistors. The simulation results show that when the radiation dose is 400 krad (Si), the logic threshold drift of the inverter is approximately 0.052 V. These results help further investigate the impact on integrated circuits in the irradiation environment.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015 TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

The aims of this study are to measure the technical efficiency (TE) of Cambodian household’s rice production and trying to determine its main influencing factors using the stochastic frontier production function. The study utilized primary data collected from 301 rice farmers in three selected districts of Battambang by structured questionnaires. The empirical results indicated the level of household rice output varied according to differences in the efficiency of the production processes. The mean TE is 0.34 which means that famers produce 34% of rice at best practice at the current level of production inputs and technology, indicates that rice output has the potential of being increased further by 66% at the same level of inputs if farmers had been technically efficient. Furthermore, between 2013-2015, TE of household’s rice production recorded -14.3% decline rate due to highly affected of drought during dry season of 2015. Moreover, evidence reveals that land, fertilizer, and pesticide are the major influencing input factors of household’s rice production, while disaster, education of household head, family size and other crops’ cultivated area are core influencing factors decreasing TE. Conversely, the main influencing factors increasing TE are irrigated area, number of plot area and sex of household head.

Availability and continuous operation under critical conditions are very important in electric machine drive systems. However, such systems, are suffering from several type of failures that affect the electric machine or the associated voltage source inverter. Therefore, fault diagnosis and fault tolerance are highly required. This paper presents a new robust deep learning-based approach to diagnosis multiple open-circuit fault in three phase two level voltage source inverter for induction motor drive applications. The proposed approach uses fault diagnosis variables obtained from sigmoid transformation of the motor stator currents. The open-circuit fault diagnosis variables are then introduced to a Bidirectional Long Short-Term Memory algorithm to detect the faulty switch(es). Several simulation and experimental results are presented to show the proposed fault diagnosis algorithm effectiveness and robustness.

Mutations in epidermal growth factor receptor (EGFR) occur in about 48% of Asian and 19% of Western patients with lung adenocarcinoma (LUAD), leading to its constitutive activation and subsequent uncontrolled cell proliferation. To counteract this, tyrosine kinase inhibitors (TKIs) have been developed, targeting EGFR activity. However, the emergence of metastases and resistance mutations often undermines the durability of the treatment response. Knowledge-based mechanistic models that replicate existing clinical trial outcomes, tailored to specific population characteristics, provide invaluable assistance in designing future clinical trials. These models are particularly effective in identifying optimal responders to specific treatments, thereby enhancing therapeutic efficacy. We have developed physiologically based pharmacokinetic (PBPK) models for gefitinib and osimertinib, representing two distinct generations of EGFR TKIs, to accurately simulate the drugs’ distribution within the primary tumor and metastatic sites following oral administration. These models were integrated with a pathophysiological mechanistic model of EGFR-mutant LUAD, enabling the representation of the effects of both gefitinib and osimertinib on EGFR activation-induced signaling pathways. This comprehensive model outputs detailed evolutions of the primary tumor and each metastatic site, facilitating the evaluation of patient progression in alignment with RECIST guidelines (version 1.1). Notably, the model encapsulates the heterogeneity within the tumor, through the representation of various subclones, each characterized by unique mutation profiles, thereby reflecting differential responses to treatment. Calibration of the model was achieved using publicly available data from the NEJ002 and FLAURA clinical trials. Rigorous visual predictive checks and statistical tests were employed to ensure the proper behavior of the model. The model adeptly replicated the time to progression observed in real clinical trials in EGFR-mutant LUAD patients receiving gefitinib or osimertinib as first-line therapy. In addition, the model was able to reproduce the results from a retrospective study comparing gefitinib and osimertinib, a study that was not used to inform the model. With a consistent virtual population as a reference, the combined model facilitated a comparative analysis of the efficacy of both treatments, thereby underscoring its utility in evaluating therapeutic strategies. The faithful replication of real-world data significantly enhances the credibility of our model, rendering it a vital investigational tool for deriving pertinent insights and informing treatment strategies, particularly in identifying optimal responders to various generations of EGFR TKIs. Following its consecutive prospective validations in the FLAURA2 and MARIPOSA trials, the model is poised to facilitate the generation of synthetic control arms in future clinical trials. This advancement promises a more nuanced analysis of covariate relationships, especially when comparing investigational treatments to established standards of care. Additionally, it potentially reduces the required patient cohort size in such trials, optimizing resource utilization.

Coronavirus disease 2019 (COVID-19) has affected medical practice. More than 7,000,000 patients died worldwide after being infected with COVID-19; however, no specific laboratory markers have yet been established to predict death related to this disease. In contrast, electrocardiographic changes owing to COVID-19 include QT prolongation and ST-T changes; however, there have been no studies on ambulatory electrocardiographic markers of COVID-19. We encountered three patients diagnosed as having COVID-19 who did not have a prior history of significant structural heart diseases. All had abnormalities in ambulatory echocardiogram parameters detected by high-resolution 24-h electrocardiogram monitoring: positive late potentials (LPs) and T-wave alternans (TWA), abnormal heart rate variability (HRV), and heart rate turbulence (HRT). Case 1 involved a 78-year-old woman with a history of chronic kidney disease, Case 2 a 76-year-old man with hypertension and diabetes, and Case 3 a 67-year-old man with renal cancer, lung cancer, and diabetes. None of them had a prior history of significant structural heart disease. Although no significant consistent increases in clinical markers were observed, all three patients died, mainly because of respiratory failure with mild heart failure. LP, TWA, HRV, and HRT were all positive in three cases with no significant structural cardiac disease at the initial phase of admission. There is a possibility that LP, TWA, HRV, and HRT have the potential to be risk stratifiers of COVID-19 pneumonia in the early phase of admission. Further accumulation of data regarding ambulatory electrocardiographic markers in patients with COVID-19 is needed.

The objective of this paper is to research the impact of electrical and physical parameters that characterize the complementary MOSFET transistors (NMOS and PMOS transistors) in the CMOS inverter for static mode of operation. In addition to this, the paper also aims at exploring the directives that are to be followed during the design phase of the CMOS inverters that enable designers to design the CMOS inverters with the best possible performance, depending on operation conditions. The CMOS inverter designed with the best possible features also enables the designing of the CMOS logic circuits with the best possible performance, according to the operation conditions and designers’ requirements.

Three Seas Initiative (3SI) is still an underresearched area and is particularly important due to historical circumstances and economic backwardness. A study was carried out to assess the impact of renewable energy and production generated by the agricultural sector on CO2 emissions in 3SI countries between 2008 and 2020. The study used panel data analysis based on the two-step system generalised method of moments (GMM) and the Dumitrescu-Hurlin panel causality test. The results show that a 1% increase in the value-added generated by agriculture increases CO2 emissions in the countries studied by 0.11%. In contrast, a 1% increase in GDP leads to a 0.29% increase in CO2 emissions. Conversely, when renewable energy consumption increases by 1%, CO2 emissions fall by 0.25% in the countries studied. One way to reduce CO2 emissions from agricultural production in the short term is to increase the share of renewables, which, incidentally, is in line with EU action.

The purpose of this study is to investigate the impact of the voltage drop of a three-phase voltage source inverter in driving brushless motors. This study also proposes an enhanced Field Oriented Control scheme that accounts for the inverter voltage drop enabling efficient drive at very low motor-speeds. Experimental results are provided to verify the theoretical study and the proposed control scheme.

Induction heating (IH) technology is widely recognized and utilized in residential applications due to its high efficiency and safe operating characteristics. Resonant inverter circuits are widely used in IH systems because of their high efficiency and ability to perform soft-switching. Among the various resonant inverters used in IH systems, the single-switch quasi-resonant (SSQR) inverter topology is typically preferred for low-cost and low-output-power applications. Despite its cost advantage, the SSQR topology has a relatively narrow soft-switching range, which can be unstable depending on the electrical parameters of the load and the resonant converter circuit. Accurately determining the capacitance value of the resonant capacitor and the inductance value of the induction coil, which are the key circuit elements of the SSQR induction cooker, is crucial for designing a reliable, efficient, and durable cooking system. In other words, there exists a critical relationship between the resonant converter circuit parameters, load characteristics, and safe operating conditions. Additionally, when considering closed-loop control methods used for power control and safety, selecting appropriate resonant circuit elements becomes vital in ensuring both reliable and efficient operation. This paper focuses on a novel and simplified design method for the SSQR inverter utilized in household appliances. The proposed method and its advantages in terms of the safe operating area of the switch are theoretically investigated and verified through simulations and prototype circuits.

Post-Shoah Christology is embedded in the unique relationship of Jews and Christians, especially Jesus’ Jewishness and the Jewish roots of Christianity, as well as Christian moral failures towards Jews before and during the Shoah. Essential for contemporary Christianity, a vibrant post-Shoah Christology confronts three main challenges, each demanding a different response. The first challenge is the reality that soon there will be no more first-generation witnesses to the Final Solution. Such is an inevitable challenge that has to be faced and prepared for. Religious pluralism is the second challenge, and includes a number of related threads, yet should ultimately be embraced. The third challenge is the (inevitable?) loss of memory, passion, and urgency, a willful forgetfulness by Christians towards the importance of the Jewish-Christian relationship, and especially, Christian failure in the Shoah. This challenge demands robust refutation and ongoing struggle. Before addressing these challenges, I will first further define and highlight the need for a post-Shoah Christology and will conclude this article with three general and three concrete hopes for a viable post-Shoah Christology.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

The objective of this work was to investigate the deacidification of bio-oils (BOs) from triglyceride-based biomass through the application of liquid-liquid extraction (LLE) in a simple stage, using methanol and water as a binary solvent and feed/solvent ratio of 1/1. For this, the effects of process parameters such as the water content present in the solvent, the content of carboxylic acids present in the bio-oil, and the extraction temperature on the deacidification process through the efficiency and distribution coefficient were evaluated, as well as the effects of such parameters on the quality of deacidified bio-oils through physical-chemical analyzes and GC-MS analysis. The results show that such process parameters significantly affect the quality of deacidified bio-oils. The ideal condition to have the highest acid removal, i.e., the highest deacidification efficiency (72.65%), is the one in which the deacidification process is performed with aqueous methanol (5% water) at 35 °C and for BOs that have a total acid number (TAN) equal to 24.38 mg KOH/g. Therefore, the process of deacidification by LLE using aqueous methanol is a promising alternative for removing carboxylic acids and other oxygenated compounds, contributing significantly to the upgrading or improving biofuels produced by catalytic thermal cracking.

This research work deals with the modeling and control of hybrid photovoltaic (PV) - Wind micro-grid using Quasi Z-Source inverter. This inverter provides better buck/boost characteristics, able to regulate the phase angle output, less harmonic content, no requirement of the filter and has high power performance characteristics over conventional inverter as major benefits. A SEPIC converter as dc-dc switched power apparatus is employed for maximum power point tracking (MPPT) functions which provides high voltage gain throughout the process. Moreover, a modified power ratio variable step (MPRVS) based perturb & observe (P&O) method has been proposed in the PV MPPT action which forces the operating point close to maximum power point (MPP). Practical responses justify the performance of hybrid PV-Wind micro-grid with Quasi Z-Source inverter structure.

This paper experimentally reveals some of the resources offered by the evolution of the instantaneous active electric power in describing the state of three-phase AC induction asynchronous electric motors (with squirrel-cage rotor) operating under no-load conditions. A mechanical power is required to rotate the rotor at no-load and this mechanical power is satisfactorily reflected in the constant and variable part of instantaneous active electric power. The variable part of this electrical power should necessarily have a periodic component with the same period as the period of rotation of the rotor. The paper proposes a procedure for extracting this periodic component description (as a pattern, by means of a selective averaging of instantaneous active electrical power) and analysis. The time origin of this pattern is defined by the time of a selected first passage through the origin of an angular marker placed on the rotor, detectable by a proximity sensor (e.g. a laser sensor). The usefulness of the pattern in describing the state of the motor rotor has been demonstrated by several simple experiments which show that a slight change in the no-load running conditions of the motor (e.g. by placing a dynamically unbalanced mass on the rotor) has clear effects in changing the shape of the pattern.

To improve efficacy and safety of sunscreen emulsions, UV‐filter skin permeation could be kept as low as possible by reducing UV‐filter content or changing emulsion composition. In this work, different lipid phase ratio (12, 14 and 16% w/w) were assessed for their ability to affect the technological and sensory properties of O/W emulsions in which bemotrizinol (BMTZ), a broad spectrum sunscreen agent, was incorporated free or loaded into nanostructured lipid nanocarriers (NLC) to reduce its release from the vehicle and, hence, its skin permeation. The following technological properties were evaluated in vitro by suitable methodologies: spreadability, viscosity, pH, occlusion factor, BMTZ release, sun protection factor (SPF). Sensory attributes were assessed by trained panelists in three different phases: before/during pick‐up, rub‐in, after application. Raising the lipid phase ratio led to an increase of viscosity and to a corresponding drop of spreadability while the incorporation of BMTZ‐loaded NLC determined a decrease of occlusion factor and an increase of SPF. No BMTZ release was observed from all emulsions. Sensory attributes were mainly affected by lipid phase ratio. These results suggest that lipid phase ratio and BMTZ incorporation into NLC could contribute to determine technological and sensory properties of O/W emulsions.

: Electric air conditioning and heating systems capacity is growing rapidly. So does the nameplate capacity of PV power plants. While demand in cooling has a positive correlation with solar irradiationirradiance, the demand in heating has an opposite relation. In this study, different approaches of to design (aggregation; energy storagethermal, battery and implicit systems storage) and control (frequency conversion; variable and adaptive load) and their effects on the efficiency of an off-grid active thermal stabilisation system based on a solar-powered heat pump are analysed. The case considered is permafrost thermal stabilisation system in Norway. It is shown that proper layout and control of the system with an adaptive load can reduce the capital expenses expenditures and the total cost of ownership by 30-40%. Increase in the efficiency capacity factor and cooling stability of the systems with the aggregated and threshold power consumervariable load due to the principle of aggregation is studied. The downside of that is the increase in compressors operation time by 50% with variable load and by 25% per unit with aggregation which means more frequent replacement in terms of motor-hours. But The the feasibility of this approaches considered are applicable for a wide range of solar-powered facilities, but the results are is quite case sensitive and depends on the prices for low-power heat pumps. The prospects of using the excess refrigerant and soil for thermal energy storage instead of traditional electrochemical batteries are considered.

This paper presents a configuration of dual output single phase current source inverter with 6 switches for microgrid applications. The inverter is capable of delivering power to two independent set of loads of equal voltages or different voltages at the load end. The control strategy is based on Integral Sliding Mode Control (ISMC). The remote monitoring of the inverter is performed with cyber infrastructure. The cyber physical test bench is developed based on Reconfigurable I/O processor (NI MyRIO-1900) for control and monitoring of the inverter. The inverter prototype is tested in cyber physical test bench in laboratory conditions. The performance of the inverter is analyzed and monitored through the remote system. Also, the inverter is analyzed with different voltage conditions.

Although migraine belongs to the main causes of disability worldwide the mechanisms of its pathogenesis are poorly known, which is among the reasons that this disease is underdiagnosed and undertreated. As migraine diagnosis is based on the subjective assessment of symptoms, there is a need to establish objective markers of its occurrence and severity. Tryptophan (TRP) metabolism has been associated with the pathogenesis of neurological and psychiatric disorders. In the present work, we investigated an association between migraine and the urine concentration of TRP and its metabolites 5-hydroxyindoleacetic acid (5-HIAA), kynurenine (KYN), kynurenic acid (KYNA) and quinolinic acid (QA) in 21 low-frequency episodic migraine patients and 32 controls. Migraine patients displayed lower urinary levels of 5-HIAA and KYNA, but KYN and QA were enhanced as compared with the controls. Consequently, the patients were characterized by different values of the 5-HIAA/TRP, KYN/TRP, KYNA/KYN, and KYNA/QA ratios. Furthermore, urinary concentration of 5-HIAA was negatively correlated with Migraine Disability Assessment score, monthly migraine, and monthly headache days. A negative correlation between Patient Health Questionnaire 9 scores assessing depression. In conclusion, the urinary 5-HIAA level may be an easy-to-determine marker of migraine occurrence and severity and may contribute to the identification of migraine patients with depression.

Here we will electrically-quantum model the neutron and proton as a three-phase alternating current electric generator, for this, we will use the theory of three-phase electric generators and vector or phasor diagrams. We will use this model to hypothesize how the quarks that form neutrons and protons with a combined mass of 10 MeV/c², can generate, through quarks-antiquarks-gluon interactions, a mass of 939.56 MeV/c² for the neutron and a mass of 938.27 MeV/c² for the proton. Using quantum mechanics and the theory of the generalization of the Boltzmann constant in curved space-time we will calculate the number of quarks-antiquarks-gluons and gravitons inside a neutron. We will also analyse βˉ decay using vector diagrams, we will calculate the tension of the string T₀ and the length of the string ℓs between quarks-antiquark and finally, we will model a black hole using a neutron equivalent model. In version 2 of this article, we will update the vector diagrams of the βˉ decay and theoretically calculate the energy of the W⁻ boson, the Z⁰ boson, and the Θ angle, Θ = arc cos (W⁻/Z⁰). We will demonstrate, through vector diagrams, that quarks-antiquarks-gluon interactions are the cause of the origin of the W⁻ boson and the Z⁰ boson. We will also demonstrate how the fine structure constant α originates. It is important to make clear, in future updates, we will describe the relationship that exists between the theory described in this paper and the Isospin theory, flavour and colour theory

Voltage Source Inverters (VSI) are the integral part of Electrical Vehicles (EV) to enhance the reliability of supply power to critical loads in vehicle to load (V2L) applications. Inherent properties of sliding mode control (SMC) makes it one of the best vailable options to achieve desired voltage quality under variable load conditions. Intrinsic characteristic of robustness associated with SMC is achieved generally at the cost of unwanted chattering along the sliding surface. To manage this compromise better, optimal selection of sliding surface coefficient is applied with proposed composite exponential reaching law (C-ERL). The novelty of proposed C-ERL is associated with the intelligent mix of exponential, power and difference functions blended with rotating sliding surface selection (RSS) technique for three phase two level VSI. Moreover, proposed reaching law along with power rate exponential reaching law(PRERL), enhanced exponential reaching law(EERL) and repeatitive reaching law(RRL) are implemented on two level three phase VSI under variable load condtions. Comparative analysis of which strongly advocates the authenticity and effectiveness of proposed reaching law in achieving well regulated output voltage, with high level of robustness, reduced chattering and low %THD.

In this paper, the deformation and phase transformation of disorder α phase at (α + γ) two phase region in as-forged Ti-44Al-8Nb-(W, B, Y) alloy are investigated by hot compression and hot packed rolling. Detailed microstructural evolution demonstrates that the as-deformed microstructure is significantly affected by deformation conditions. The mircrostructure differences are mainly due to temperature drop and strain rate. The evolution of α lamelae into α grains is detailed descripted. Moreover, the disorder α lamellae can also be decomposed into some new α grains by the assisted decomposition mechanism of γ grains. Microstructure evolution model of current TiAl alloy at 1250 °C during hot rolling is built.

This paper introduces the complex Rayleigh-van der Pol-Duffing oscillators (RVDOs), which are hyperchaotic and can be either autonomous or non-autonomous. The fundamental dynamics of the autonomous and nonautonomous complex RVDOs including dissipation, symmetry, fixed points and their stability are studied. These oscillators are found in various important fields of physics and engineering. The paper proposes a scheme to achieve phase synchronization (PS) and antiphase synchronization (APS) for different dimensional models. These kinds of synchronization are considered as generalization of several other types of synchronization. For this scheme we use the active control method based on Lyapunov stability theory. By analytically determining the control functions, the scheme achieved PS and APS. Our scheme is applied to study PS of hyperchaotic behaviours for two distinct hyperchaotic non-autonomous and autonomous complex RVDOs. Additionally, the scheme is employed to achieve APS of chaotic real non-autonomous RVDO and hyperchaotic complex autonomous RVDO, including those with different dimensions. Our work presents numerical results that plot the amplitudes and phases of these hyperchaotic behaviours, demonstrating the successful achievement of PS and APS.

Duplex Stainless Steels (DSS) and Superduplex Stainless Steels (SDSS) are an important class of stainless steels because they combine the benefits of austenite and ferrite phases, resulting in steels with better mechanical properties and higher corrosion resistance. Due to these characteristics are widely employed in various industries. However, the appearance of deleterious phases in their microstructure impairs the properties of DSS and SDSS. Among the deleterious phases, the main one is the sigma phase (σ), which can be nucleated when the steel is exposed to the temperature range between 650 °C and 900 °C, reducing its toughness and resistance to corrosion. In a previous work, Fonseca and collaborators used two descriptors of the microstructural path to analyze the formation of sigma phase (σ), SV, interfacial area per unit volume between sigma phase and austenite, and <λ>, mean chord length of sigma, both in function of the VV, volume fraction of sigma, known in the literature as microstructural partial path (MP). In this work, the contiguity ratio is applied for the first time to describe the microstructural path in the study of sigma phase precipitation in SDSS. The contiguity ratio showed that the distribution of the ferrite/sigma boundaries is homogeneous. Thus, it is reasonable to infer that one has a uniform distribution of sigma phase nuclei within the ferrite. About the kinetics of sigma phase formation, the DSS can be described by the classical JMAK equation, whereas for the SDSS, the kinetics tends to follow the Cahn model for grain edge nucleation. Finally, we present the 3D reconstruction of the sigma phase in SDSS. The results demonstrate that the sigma phase nucleates at the edges of the ferrite/austenite interfaces. Moreover, the sigma phase grows consuming the ferrite, but it is not fully interconnected.

In the case of long-stator linear drive, unlike rotative drives for which speed or position sensors are a single unit attached to the shaft, these sensors extend along the guideway. The position signals transmitted from maglev vehicle can’t meet the need of the real-time propulsion control in the on-ground inverter power substations. In this paper the design of the propulsion inverter control system with a position estimator for driving long-stator synchronous motor in high speed maglev train is proposed. The experiments have been carried out at the 150m long guideway in O-song test track. To investigate the performance of the position estimator, the propulsion control system with and without the position estimator are compared. The result confirms that the proposed strategy can meet the dynamic property need of propulsion inverter control system for driving long-stator linear synchronous motors

The structure of arylpiperazine moieties as an important pharmacophore could generate wide pharmacological activities．Arylpiperazine derivatives referred in this paper possessed antitumor activity. The title compounds were crystallized by slow evaporation. 2-(4-(2-(4-Phenylpiperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione(1), 2-(4-(2-(4-(4-Bromophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (2) and 2-(4-(2-(4-(4-Chlorophenyl)piperazin-1-yl)ethyl)benzyl)isoindoline-1,3-dione (3) crystallizes in the triclinic space group P-1 with two molecules in the unit cell. The unit cell parameters for 1 are a = 6.9159(14) Å, b = 9.999(2) Å, c = 16.925(3) Å, α = 88.25(3)°, β = 85.14(3) °, γ = 79.22(3) °. The unit cell parameters for 2 are a = 6.9995(14) Å, b = 9.919(2) Å, c = 17.671(4) Å, α= 97.55(3)°, β = 92.19(3) °, γ = 102.23(3) °. The unit cell parameters for 1 are a = 6.9872(14) Å, b = 9.863(2) Å, c = 17.557(4) Å, α=96.81(3)°, β = 91.89(3) °, γ = 101.74(3) °. Pi-pi interactions were observed between molecules, and compound 2 and 3 showed halogen interactions between molecules nearby, which was different from compound 1.

Plantar flexors (PF) spasticity is known to poorly correlate with active dorsiflexion (DF) impairment throughout the swing phase of hemiparetic gait. Spastic Cocontraction, instead, stemming from descending pathways, potentially misdirect antagonist PF activity opposing DF during swing. Electromyographic (EMG) recordings, while unable to differentiate between reflex-based and descending origins, may offer valuable insights into this distinction by exploring PF EMG activity after tibial nerve neurotomy (which eliminates PF spasticity). Eleven subjects with hemiparesis walking at comfortable velocity and 11 controls walking at comfortable and slow velocity, underwent kinematic and PF/DF EMG analysis. Five of the hemiparetic subjects underwent tibial neurotomy &gt;1 year prior. We evaluated spasticity at rest (Tardieu scale), maximal ankle dorsiflexion, tibialis anterior agonist recruitment and gastrocnemius medialis and soleus cocontraction coefficients during swing. At slow velocity, controls (0.80±0.12 m/s) moved at a similar pace as hemiparetic subjects (0.73±0.37 m/s, NS). Hemiparetic subjects showed: (i) reduced ankle DF across swing (ii) increased PF cocontraction, including before any DF (iii) higher cocontraction despite absent spasticity in tibial neurotomy subjects (iv) higher tibialis anterior recruitment. Increased PF cocontraction occurs in the absence of spasticity or ankle DF despite higher agonist recruitment. Spastic cocontraction is a major factor limiting active DF at swing, unlike spasticity.

A single qubit may be represented on the Bloch sphere or similarly on the 3-sphere S3. Our goal is to dress this correspondence by converting the language of universal quantum computing (UQC) to that of 3-manifolds. A magic state and the Pauli group acting on it define a model of UQC as a positive operator-valued measure (POVM) that one recognizes to be a 3-manifold M3. More precisely, the d-dimensional POVMs defined from subgroups of finite index of the modular group PSL(2, Z) correspond to d-fold M3- coverings over the trefoil knot. In this paper, one also investigates quantum information on a few ‘universal’ knots and links such as the figure-of-eight knot, the Whitehead link and Borromean rings, making use of the catalog of platonic manifolds available on the software SnapPy. Further connections between POVMs based UQC and M3’s obtained from Dehn fillings are explored.

A single qubit may be represented on the Bloch sphere or similarly on the $3$-sphere $S^3$. Our goal is to dress this correspondence by converting the language of universal quantum computing (uqc) to that of $3$-manifolds. A magic state and the Pauli group acting on it define a model of uqc as a POVM that one recognizes to be a $3$-manifold $M^3$. E. g., the $d$-dimensional POVMs defined from subgroups of finite index of the modular group $PSL(2,\mathbb{Z})$ correspond to $d$-fold $M^3$- coverings over the trefoil knot. In this paper, one also investigates quantum information on a few \lq universal' knots and links such as the figure-of-eight knot, the Whitehead link and Borromean rings, making use of the catalog of platonic manifolds available on SnapPy. Further connections between POVMs based uqc and $M^3$'s obtained from Dehn fillings are explored.

This paper presents an improved droop control strategy for grid-connected inverter power stability and power quality under distorted with consideration of grid fluctuation and inter-harmonics. An instantaneous frequency without PLL and amplitude of capacitor voltage feed-forward control strategy is given to power stability control, meanwhile a grid current feedback control is given by an incomplete derivation with a high-pass filter, so that the harmonics and inter-harmonics current can be suppressed. These approaches can provide both good active and reactive power dynamic response under fluctuation of frequency, and rejection ability against harmonic and inter-harmonic voltage. Based on model of inverter, the proposed control strategies are designed in detail. Simulations and experiments are present to validate the effectiveness of proposed method.

In this research, atomistic molecular dynamics simulations are combined with mesoscopic phase-field computational methods in order to investigate phase-transformation in polycrystalline Aluminum microstructure. In fact, microstructural computational modeling of engineering materials could help to optimize their mechanical properties for industrial applications (e.g. directional solidification for turbine blades). As a result, a multiscale modeling approach is developed to find a relation between manufacturing variables (e.g. temperature) and microstructural properties of crystalline materials (e.g. grain size), which could be used to develop an advanced manufacturing process for sensitive applications. The results show that atomistic modeling of grain growth could be used as a first-principle approach in order to study phase transformation's kinetics, which could capture morphology of polycrystalline materials more accurately. On the other hand, phase-field mesoscopic approach needs less computational efforts, but still it relies on semi-empirical data to capture accurate phase transformation regimes, which makes this approach suitable for rapid examining of new manufacturing conditions as well as its effects on microstructural properties of polycrystalline materials.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

The aim of this paper is to provide a new perspective on the conditions for the multiple dimensions of concerns, and to understand why some wind power projects run smoothly while others lead to unexpected outcomes due to local resistance. The paper described how multiple community concerns about wind power project planning can be described using conflict management theory and by using different procedures to handle tangible and intangible concerns. Policy recommendations are given on how: to minimise overflowing and the risk of the conflicts; to avoid “boxing” community concerns in categories; to give more attention to the intangible and less calculable concerns; to secure appropriate and early planning with proactive involvement of local communities.

A key step in the study of tree pathology is the identification of appropriate method for inoculating pathogens of diseases in branch and trunk. Pathogens of diseases in branch and trunk are commonly inoculated through punching, burning, and toothpick inoculation. However, there is a lack of comparative analysis of the inoculation outcomes of these three methods. In this work, Six‐year‐old P. alba var. pyramidalis were inoculated with V. sordida, using punching, burning, and toothpick techniques, respectively, to investigate the differences in the effectiveness of these inoculation methods. Results reveal that the incidence rate was 93.55% in the toothpick inoculation group, significantly higher than 80.65% in the burning inoculation group (p = 0.007), while punching inoculation exhibited significant pathological responses in the early stages, with spontaneous healing in the later stage. Addi-tionally, toothpick inoculation was more efficient in inducing Valsa canker when inoculating the pathogen at the bottom of the tree, with lower intra‐ and inter‐row spacing (stand density) providing better outcomes than higher intra‐ and inter‐row spacing. The results of this study demonstrate that toothpick inoculation is an optimal option for studying the artificial inoculation of V. sordida in six‐year‐old P. alba var. pyramidalis, providing technical support for research on poplar diseases and offering a theoretical basis for the inoculation of other diseases in branch and trunk.

When a grid-forming (GFM) inverter is connected to a low or medium voltage weak power grid, the line impedance with resistive-inductive characteristics will cause power coupling. Typical GFM decoupling control strategies are designed under nominal line impedance parameters. However, there are deviations between the nominal line impedance and actual parameters, resulting in poor decoupling effects. Aiming at this problem, this paper proposes a power decoupling strategy based on a reduced-order extended state observer (ESO). Firstly, the power dynamic model of GFM is established based on the dynamic phasor method. Then, the model deviation and power coupling due to line impedance parameter perturbation are estimated as internal disturbances of the system, and the disturbances are compensated on the basis of typical power control strategy and virtual impedance decoupling. Good decoupling performance is obtained under different impedance parameters, improving the control strategy's robustness. Finally, the effectiveness of the proposed method is verified by the results of RT Box hardware-in-the-loop experiments.

A robust explicit model predictive control (EMPC)-based frequency adaptive grid voltage sensorless control is developed for a grid-connected inverter (GCI) via a linear matrix inequality (LMI) approach under the model parameter uncertainties and non-ideal grid environment. The control scheme is achieved by an enhanced prediction model rather than the conventional prediction model provided by fixed parameters to maintain the quality of grid currents injected into the grid when the model parameters are varied. Furthermore, an LMI-based observer is integrated with the disturbance observer to improve the reference tracking performance and reject disturbances. The proposed observer is employed for the grid frequency adaptive control without need of grid voltage sensors. The proposed current controller and observer employ the LMI scheme to maintain a stable and robust operation of the GCI. The discrete-time frequency response and pole-zero map analyses are used to investigate system stability and robustness against parameter uncertainties. Comprehensive simulation, experimental results and analyses clearly demonstrate the robustness of the proposed control scheme under various adverse test conditions with unexpected grid and system uncertainties.

This research proposes a roof-mounted auxiliary power supply (APS) system for 600VDC low-floor light rail vehicle (LRV). The proposed APS system consists of five parallel-connected dc-ac inverter modules (modules 1-5). The inverter modules 1 and 2 are three-phase dc-ac inverters for compressor motors of the cooling system, and the inverter modules 3 and 4 are three-phase dc-ac inverters for air pump motors of the braking system. The inverter module 5 is single-phase dc-ac inverter for 220VAC power supply for onboard electric loads. Simulations and experiments were carried out under variable load torque and output frequency for modules 1 – 4; and under full and no resistive loads for the inverter module 5. The measured total input current and total input power of the proposed APS system under full load condition are 118.76A and 71.25kW. Essentially, the proposed APS system is operationally applicable to the 600VDC low-floor RLV. Besides, the novelty of this research lies in the use of five parallel-connected inverter modules, unlike in the conventional APS systems which require three-phase output transformer or isolated dc-dc converter. Specifically, the proposed APS system requires neither three-phase output transformer nor isolated dc-dc converter.

This study aims to implement a SSDBI (single-stage differential boost inverter, SSDBI) applying in a single-stage BESS (battery energy storage system, BESS) topology, which can supply power from lower voltage battery module to AC load. Compared with the common two-stage topology, which has a two-stage converter and higher voltage battery module array, the single-stage topology can reduce the number of cells and components, and improve the power density. In addition, a modified SPWM control was proposed to reduce the control complexity of the SSDBI while improving the THD of the inverter. The modified SPWM control can reduce the duty ratio of the SSDBI and the stress on the components to improve the AC voltage output waveform and reduce the THD value about 2.654%.

The first objective of this paper is to investigate the scaling behavior of liquid-vapor phase transition in FCC and BCC metals starting from the zero-temperature four-parameter formula for cohesive energy. The effective potentials between the atoms in the solid are determined using lattice inversion techniques as a function of scaling variables in the above formula. These potentials are split into repulsive and attractive parts as per the Weeks-Chandler-Anderson prescription, and used in the coupling-parameter expansion for solving the Ornstein-Zernike equation supplemented with an accurate closure. Thermodynamic quantities obtained via the correlation functions are used to obtain critical point parameters and liquid-vapor phase diagrams. Their dependence on the scaling variables in the cohesive energy formula are also determined. Equally important second objective of the paper is to revisit coupling parameter expansion for solving the Ornstein-Zernike equation. The Newton-Armijo non-linear solver and Krylov-space based linear solvers are employed in this regard. These methods generate a robust algorithm that can be used to span the entire fluid region, except very low temperatures. Accuracy of the method is established by comparing the phase diagrams with those obtained via computer simulation. Avoidance of the 'no-solution-region' of Ornstein-Zernike equation in coupling-parameter expansion is also discussed. Details of the method and the complete algorithm provided here would make this technique more accessible to researchers investigating thermodynamic properties of one component fluids.

The wood-based panel industry is experiencing an excessive accumulation of solid residues from the production of medium-density fiberboard (MDF) panels and moldings. It is possible to create new MDF products with acceptable physical and mechanical properties by revaluing MDF residues. Additionally, those products’ thermal properties can be improved by incorporating phase change materials (PCMs). This study aims to develop a wood-based fiberboard made of MDF residues, capable of storing thermal energy. Two types of PCMs, two PCM ratios, and two types of adhesives were used to produce eight different types of panels. The vertical density profile, thickness swelling, water absorption, internal bond (IB), and static bending properties – modulus of elasticity (MOE) and modulus of rupture (MOR) – were determined for each panel type. The specific heat of the panels was also determined. The results show the panels’ densities were greater than 700 kg/m3. Thickness swelling in water improved by 23% compared to the reference value of the control panel PCMs after PCM incorporation. The highest IB value was 1.30 MPa, which is almost three times the minimum required by regulation standards. The incorporation of PCMs reduced the panels’ bending properties compared to the properties of the control panels. Even though the values obtained are sufficient to comply with the minimum values set out in ANSI standard A208.2 with a MOE value of 2072.4 MPa and the values obtained are sufficient to comply with the minimum standards with a MOE value of 2072.4 MPa and a MOR value of 16.4 MPa. When microencapsulated PCM is used, the specific heat of the panels is increased by more than 100% over that of the control panels. This study develops a feasible alternative for using MDF residues: to create fiberboard that is capable of storing thermal energy and has adequate physical and mechanical properties.

A review of influence of drag-reducing agents on curved pipe flows is presented in this work. In addition, this review outlined proposed mechanism, friction factor and fluid flux models for drag-reducing agents in curved pipe flows. Our finding reveals that drag reduction by additives in curved pipes is quite significant but generally lower than the corresponding drag reduction in straight pipes. It decreases with increase in curvature ratio and more pronounced in the transition and turbulent flow regimes. Drag reduction strongly depends on the polymers and surfactants’ concentrations as well as the bubble fraction of micro-bubbles. It is also reported that drag reduction in curved pipes depends on temperature and existence of dissolved salts in the fluids. Maximum drag reduction asymptote differed between straight and curved pipes and between polymer and surfactant. No definite conclusion could be drawn as regards drag reduction for two-phase flow in curved pipes due to the limited studies in this area. Many questions such as the mechanism of drag reduction in curved pipes and how drag-reducing agents interact with secondary flows still remained unanswered. Hence, some research gaps have been identified with recommendations for areas of future researches.

In this paper, the Phase-Scheduled-Command FXLMS algorithm with the phase error between the disturbance and command signal is analyzed in detail. The influence of the phase error on the convergence time constant, convergence rate, and performance of convergence is explained for both stationary and nonstationary disturbance signals case. For stationary disturbance, the phase error slightly increases the convergence rate but heavily increases the distance of the optimum vector from the initial value, leading to poor convergence time constant performance. For nonstationary disturbance, the existence of phase error leads to poor convergence performance in every step, resulting in poor sound profiling performance. And the estimation of the phase error influence is developed in the closed form. Simulations are performed to demonstrate the validity of the analysis results.

The design and integration of intelligent energy management systems in hybrid Electric Vehicle (EV) charging stations, leveraging Industry 4.0 and renewable energy sources, is crucial for advancing sustainability, efficiency, and technological development. This paper introduces a pioneering hybrid EV charging station that employs hybrid power sources, combining photovoltaic panels, a battery, and a fuel cell, each operating at 240V and 14A. Utilizing wireless power transfer technology, the system comprises five integral blocks: a power source, a boost converter, a High-Frequency (HF) inverter, transfer coils, and EV batteries. The optimization process involves two key stages: i) maximum power point tracking optimization of the boost converter, ensuring maximum power generation by varying the duty cycle between 10% and 90%, and ii) the HF phase employing a class-ϕ2 inverter at 30 MHz, synchronized with the resonant frequency of wireless power transfer coils. Control is executed through a digital signal processor card utilizing zero-voltage switching for efficient operations. This design enhances sustainability in EV charging solutions by optimizing power transfer through the use of hybrid sources.

Colorectal cancer (CRC) is the third most commonly diagnosed cancer worldwide, and despite advances in treatment, survival rates are still low; therefore, the development of novel drugs is imperative. Acetylcorynoline (ACN) is derived from Corydalis ambigua. The effect of ACN on colon cancer is still unknown. Therefore, we investigated its potential effects. Our data showed that ACN inhibited cell viability and proliferation. Moreover, ACN induced apoptosis and cell cycle arrest by inhibiting cell growth. In the present study, we hypothesized that ACN regulates c-Myc through CNOT2 or MID1IP1. ACN reduced the protein expression of oncogenic genes, decreased c-Myc half-life, and rapidly inhibited the serum stimulation response. Moreover, knockdown of CNOT2 and MID1IP1 with ACN increased apoptosis and further reduced the expression of oncogenes. In addition, ACN exhibited a synergistic effect with low-dose of 5-fluorouracil (5-FU) and doxorubicin (Dox). Collectively, our data demonstrates that ACN inhibited c-Myc expression through CNOT2 and MID1IP1 and induced apoptosis. These findings indicate the potential of ACN as a therapeutic agent against colon cancer.

Growth and yield of boreal tree species are discussed. A growth model is applied, along with verified yield models of sawlogs and veneer logs. Using the normal forest-principle, thinning schedules and rotation ages maximizing the estate-level capital return rate are clarified. Regeneration expenses are amortized at the end of any rotation. Consequently, capitalizations are greater and rotations longer than in recent studies. The capital return rate is a weak function of initial stem count but differs by tree species. The initial stem count strongly contributes to biomass stored in trees. The most promising way of increasing the capital return rate is the reduction of regeneration expenses. Thinnings are triggered by stand volumes of at least 200 m3/ha. The average commercial trunk volume of trees removed in thinnings always exceeds 200 liters. Risk aversion theory proposes short rotations and low stem count in seedling planting unless carbon storage compensation exists.