Enclosed public spaces are the hotspots for airborne disease transmission. To measure and maintain indoor air quality in terms of airborne transmission, an open source, low cost and distributed array of Particulate Matter Sensors has been developed and named as Dynamic Aerosol Transport for Indoor Ventilation or DATIV system. This system can use multiple Particulate Matter Sensors (PMS) simultaneously and can be remotely controlled using a Raspberry Pie based operating system. The data acquisition system can be easily operated using the GUI within any common browser installed on a remote device such as a PC or Smartphone with corresponding IP address. The software architecture and validation measurements are presented together with possible future developments.

This study examines geothermal energy extraction potential from the basement rock within the Denver-Julesburg (DJ) Basin, focusing on flow performance and heat extraction efficiency of different geothermal well configurations. It specifically compares U-Shaped, V-Shaped, Inclined V-Shaped, and Pipe-in-Pipe configurations against Enhanced Geothermal Systems (EGS) setups. Through numerical modeling, we evaluated the thermal behavior of these systems under various operational scenarios and fracture conditions. Results suggest that while closed-loop systems offer moderate temperature increases, EGS configurations show substantial potential for high-temperature extraction. This underscores the importance of evaluating well configurations in complex geological settings like the DJ Basin. The insights from this study aid in strategic geothermal energy planning and development, marking significant advancements in geothermal technology and setting a foundation for future explorations and optimizations.

The development of virtual models has recently been generalized in the field of complex mechatronic product design. Virtual models have various advantages such as: the systemic design approach, most often parametric, the implementation of extreme, expensive, and perhaps risky scenarios for the operation of the designed product, the testing of a large number of variants, etc. The main contribution of the paper consists of the development of an interface family called DeSeRoI (Dedicated Serial Robot Interface). Each member of the interface family integrates Simulink libraries and is created by the programmer in accordance with user requests. It follows that the interfaces composing the DeSeRoI family can have different levels of complexity depending on user needs and constraints. We are implementing a MATLAB-based application with user-provided configuration for serial robots in order to automatically visualize the kinematics data and simulation. Within MATLAB, two scripts are created responsible for generating Simulink models that compute the kinematics problem. One of the scripts (Main) saves information about the configuration of the robot and the other one (Generates_Simulink_Models) computes the kinematics problem. Different types of functions (software module) have been developed. Using these functions, the Simulink models result as modular entities. The automated approach eases user’s interaction and understanding of serial robots’ kinematics by performing the simulation procedure in a shorter amount of time and with higher efficiency, assuring a precise outcome despite the chosen parameters.

Biohydrogen is a versatile energy carrier for the generation of electric energy from renewable sources. Hydrogenases can be used in enzymatic fuel cells to oxidize dihydrogen. The rate of electron transfer (ET) at the anodic side between the [NiFe]-hydrogenase enzyme distal iron-sulfur cluster and the electrode surface can be described by the Marcus equation. All parameters for the Marcus equation are accessible from DFT calculations. The distal cubane FeS-cluster has a three cysteine and one histidine coordination [Fe₄S₄](His)(Cys)₃ first ligation sphere. The reorganization energy (inner- and outer-sphere) is almost unchanged upon a histidine-to-cysteine substitution. Differences in rates of electron transfer between the wild-type enzyme and the all-cysteine mutant can be rationalized by a diminished electronic coupling between the donor and acceptor molecules in the [Fe₄S₄](Cys)₄ case. The fast and efficient electron transfer from the distal iron-sulfur cluster is realized by a fine-tuned protein environment which facilitates the flow of electrons. This study enables the design and control of electron transfer rates and pathways by protein engineering.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

In this paper we develop from first principles a unique law pertaining to the flow of fluids through closed conduits. This law, which we call “Quinn’s Law”, may be described as follows: When fluids are forced to flow through closed conduits under the driving force of a pressure gradient, there is a linear relationship between the normalized dimensionless pressure gradient, P_Q, and the normalized dimensionless fluid current, C_Q. The relationship is expressed mathematically as: P_Q = k₁ +k₂C_Q. This linear relationship remains the same whether the conduit is filled with or devoid of solid obstacles. The law differentiates, however, between a packed and an empty conduit by virtue of the tortuosity of the fluid path, which is seamlessly accommodated within the normalization framework of the law itself. When movement of the fluid is very close to being at rest, i.e., very slow, this relationship has the unique minimum constant value of k₁, and as the fluid acceleration increases, it varies with a slope of k₂ as a function of normalized fluid current. Quinn’s Law is validated herein by applying it to the data from published classical studies of measured permeability in both packed and empty conduits, as well as to the data generated by home grown experiments performed in the author’s own laboratory.

We consider that the relationship between entropy in statistical mechanics, which is the Boltzmann principle, and the complex velocity potential in complex fluid dynamics. We define the generalized complex entropy which expanded entropy from real space to complex space. We show that the complex entropy can be expressed by the composition of sources, sinks and laminar flows of the complex velocity potential. Therefore, the complex entropy is considered a special case of the complex fluid dynamics,that is, the complex velocity potential. In other words, we show that the complex entropy is expressed by the complex velocity potential. Moreover, we show that a complex number is expressed by the complex entropy. Thus, we show that the complex velocity potential is expressed by the complex entropy. Namely, we will expand entropy to complex space and see that the complex entropy is expressed by the complex velocity potential. Furthermore, we examine the possibility that it is an expansion of Boltzmann's principle and Planck distribution.

An analogy between magneto-fluid dynamics (MFD/MHD) and geostrophic flow in a rotating frame of reference including the existence of electromagnetic columns identical to Taylor-Proudman columns is identified and demonstrated theoretically. The latter occurs in the limit of large values of a dimensionless group representing the magnetic field number. Such conditions are shown to be easily satisfied in reality. Consequently, the electromagnetic fluid flow subject to these conditions is two dimensional and the streamlines are being shown to be identical to the pressure lines in complete analogy to rotating geostrophic flows. An experimental setup is suggested to confirm the theoretical results experimentally.

The construction industry has a notable negative impact on the environment; thus, the promotion of the use of timber structures is an alternative to mitigate its effects. The research develops an artificial intelligence-based decision approach in the calculation of timber structures focused on the enhancement of the sustainability of roof structures. Based on the optimization carried out through genetic algorithms and the framework established in Eurocode 5, a general set of equations has been proposed for a laminated timber roof structure. The tool, which determines the most suitable roof structure for each strength class of laminated timber, allows for the determination of the dimensions of beams and purlins and their respective separations in order to minimize wood consumption. The ultimate goal is to offer multiple solutions regarding strength classes and structural designs in order to foster informed sustainable choices that promote efficient use of resources in construction.

The paper presents a proposal for an in-house mathematical model of a liquid flat-plate solar collector. The proposed model is a one-dimensional distributed parameter model enabling simulations of the collector operation under arbitrarily variable boundary conditions. The model is based on the solution of energy balance equations for all components of the collector. The formulated differential equations are solved iteratively using an implicit difference scheme. In order to obtain a stable numerical solution, it is necessary to use appropriate steps of the time and spatial division. These were found by comparing the results obtained from the model with the results of the analytical solution available in the literature for the transient state, which constitutes the novelty of the present study. The accuracy of the results obtained from the model was verified experimentally by comparing the measured and the calculated history of the fluid temperature at the outlet of the collector. The calculation of the collector time constant is proposed in the paper as an example of the model practical application. The results of the time constant calculation were compared with the values obtained experimentally on the test stand. This is another novelty of the presented research. The analysed collector instantaneous efficiency was then calculated for selected outdoor conditions. The presented mathematical model can also be used to verify the correctness of the collector operation. Comparing, on an ongoing basis, the measured and the calculated values of the fluid temperature at the collector outlet, conclusions can be drawn about the process of solar glass fouling or glycol gelling. The model's simplicity and the low computational demands enable such comparisons in an online mode.

The main objective of this work is the assessment of the annual number of hospital admissions for respiratory disease (HARD) due to the exposure to in-healable particulate matter (PM10), within the greater Athens area (GAA), Greece. Towards this aim, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) recorded in six monitoring stations located in the GAA, for a 13-year period 2001-2013, is used. Initially, a descriptive statistical treatment of PM10 concentrations took place. Furthermore, the AirQ2.2.3 software developed by the WHO was used to evaluate adverse health effects by PM10 in the GAA during the examined period. The results show that, during the examined period PM10 concentrations present a significant decreasing trend. Also, the mean annual HARD cases per 100,000 inhabitants ranged between 20 (suburban location) and 40 (city centre location). Approximately 70% of the annual HARD cases are due to city centre residents. In all examined locations, a declining trend in the annual number of HARD cases is appeared. Moreover, a strong relation between the annual number of HARD cases and the annual number of days exceeding the European Union daily PM10 threshold value was found.

In the realm of metal steel and iron manufacturing, there is a constant drive to optimize production efficiency and enhance the quality of the final products. This abstract explores a paradigm shift in this industry through the utilization of Computational Fluid Dynamics (CFD) as a powerful tool for achieving these goals .The study focuses on various critical aspects of the manufacturing process. Firstly, it delves into three-phase processes such as slag and gas entrainment in liquid steel, which have a significant impact on the overall product quality. Understanding and optimizing these processes is crucial to ensure the desired chemical composition and physical properties of the final metal.The abstract investigates the role of CFD in vacuum degassing, a process that plays a pivotal role in removing impurities, such as hydrogen and oxygen, from the liquid steel. By leveraging CFD to simulate and analyze the fluid flow patterns, researchers and engineers can design more efficient vacuum degassing systems, leading to improved product purity and reduced waste.Another crucial aspect explored in this abstract is the alloy melt and mixing process. By employing CFD simulations, researchers can gain insights into the movement of different alloy components and optimize their distribution within the melt. This aids in achieving the desired alloy composition, ensuring uniformity, and enhancing the mechanical properties of the final product.In addition, the study delves into the movement and flotation of inclusions, which are unwanted impurities present in the metal. CFD can be utilized to model and analyze the behavior of these inclusions, enabling engineers to design efficient strategies for their removal, thereby enhancing the purity and integrity of the final product.Moreover, the abstract considers the impact of melt temperature losses, which can occur during different stages of the manufacturing process. By employing CFD, it becomes possible to understand and mitigate these temperature losses, leading to improved energy efficiency and better control over the manufacturing parameters.Part 1 of this abstract critically evaluates the use of CFD in iron making, analyzing its benefits and limitations. It highlights how CFD can aid in process optimization, improving the understanding of complex phenomena involved in iron making, and ultimately leading to enhanced production efficiency.Part 2 focuses on the application of CFD in steel making and steel operation. It explores the fluid flow dynamics during different stages of steel production, including refining, casting, and rolling. By leveraging CFD, engineers can optimize these processes, leading to improved product quality, reduced defects, and increased productivity.This abstract demonstrates the transformative potential of Computational Fluid Dynamics in metal, steel, and iron manufacturing. By utilizing CFD as a tool to model and analyze complex fluid flow phenomena, researchers and engineers can revolutionize the production process, maximizing efficiency, and ensuring high-quality end products.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

The coseismic surface three-dimensional deformation fields were significant for quantified the geometric and kinematic characteristics of earthquake rupture faults. Traditional geodetic techniques were constrained by their intrinsic limitations, such as InSAR, which could only extract far-field deformation fields due to its incoherence, and GNSS, which could only acquire deformations at discrete points. The recently developing optical pixel correlation technique based on high resolution remote sensing images could acquire the near-field coseismic horizontal deformation. In this study, the vertical displacement field of the 2022 Mw 6.6 Menyuan earthquake was obtained by differencing the pre- and post-earthquake DEMs from GaoFen-7 stereo satellite images. Further, the line-of-sight (LOS) and azimuthal (AZI) directions far-field deformations by InSAR, the horizontal near-field deformation by optical pixel correlation based on pre- and post-earthquake GF-2/7 images, and the vertical deformation by differencing the pre- and post-earthquake DEMs, were incorporated to comprehensively solve the complete three-dimensional deformation fields of the 2022 Mw 6.6 Menyuan earthquake. Firstly, the vertical displacement field by differencing DEMs indicated there were significant vertical displacements about 1 m at the bend region, which was induced by the local compressive stress. In addition, at the epicenter on the middle segment of ruptured Lenglongling fault (LLLF), the maximum lifting occurred on the southern sides of the main and secondary faults exceeded 2 m. Secondly, the three-dimensional deformation fields solved by multiple deformation data demonstrated that the near-field deformation field calculated by optical pixel correlation method could quantify the displacements distributed over the rupture fault zone, which were not available on the InSAR deformation maps. Finally, the surface 2D strain derived from the displacement maps calculated by optical pixel correlation revealed high strain concentration on the rupture fault zone. Our study focused on the complete surface three-dimensional deformation estimation from multiple far- and near-field deformation data, and provided a new perspective for a deeper understanding of the characteristics of coseismic surface deformation and the rupture pattern of the fault.

The information of seismic damage of buildings in SAR images of different time phase, especially in SAR images after earthquake, is easily disturbed by other factors, which affects the accuracy of information discrimination. In order to identify and evaluate the distribution information of the seismic damage accurately and make full use of the abundant texture features in the SAR image. The conventional method of change detection based on texture features usually takes the pixel as the calculating unit. In this paper, a method of texture feature change detection of SAR images based on watershed segmentation algorithm is proposed. Based on the optimization of texture feature parameters, the feature parameters are segmented by the watershed segmentation algorithm, and the feature object image is obtained. This method introduces the idea of object oriented, and carries out the calculation of the difference map at the object level, Finally, the classification threshold value of different types of seismic damage types is selected, and the recognition of building damage is achieved. Taking the ALOS data before and after the earthquake in Yushu as an example to verify the effectiveness of the method, the overall accuracy of the building extraction is 88.9%, Compared with pixel-based methods, it is proved that the proposed method is effective.

This study presents a novel approach to understanding evolutionary dynamics through topological analysis of genotypic structures. We model the genome of a simple organism as a topological torus undergoing mutations at a constant rate of 1% per generation. Employing persistent homology and other topological data analysis techniques, we investigate how these mutations influence the overall topology of the genomic structure over time. Our simulations reveal that specific critical mutations lead to significant changes in the homotopic and homologic properties of the torus. We interpret these topological shifts as potential markers for the formation of new subspecies. By identifying the precise points of topological "breaks" within the toroidal genomic representation, our model provides a quantitative framework for observing the incremental transformations that underpin major evolutionary developments. The results offer new insights into the thresholds of speciation and adaptation, demonstrating how gradual genetic changes can accumulate to produce qualitative shifts in organismal traits. This approach bridges the gap between microscopic genetic mutations and macroscopic evolutionary outcomes, potentially revolutionizing our understanding of evolutionary processes. Our findings have implications for various fields, including theoretical biology, genetic engineering, and conservation biology. The model provides a novel perspective on genetic resilience and adaptability, offering a foundation for future research on the relationship between genomic topology and evolutionary trajectories. It also emphasizes the innovative nature of the research and its potential impact on multiple fields of study.

In this article we compute many topological indices for the family of Möbius ladder. At first we give general closed form of M-polynomial of this family and recover many degree based topological indices out of it. We also compute Zagreb indices and Zagreb polynomials of this family.

This study presents two interconnected mathematical models: one describing the stability and bifurcation dynamics of ecological biomes, and another simulating the progressive deformation and structural failure of a toroidal object. Both models explore topological changes in complex systems, bridging concepts from ecology, materials science, and mathematical physics. The first part introduces a dynamic model of ecological biomes, incorporating seasonal oscillations and external pressures. We define equations for topology updates, seasonal effects, and pressure impacts, culminating in a bifurcation condition that represents a critical shift in the biome's equilibrium state. This model provides insights into the resilience and tipping points of ecological systems under varying environmental stresses.The second part extends these concepts to a three-dimensional toroidal structure. We present parametric equations describing the torus geometry and develop a time-dependent deformation model that includes both stochastic and deterministic elements. A novel twisting deformation component enhances the realism of the structural changes. We define a critical threshold for maximum displacement, beyond which the torus undergoes structural failure, analogous to the bifurcation point in the biome model. Both models are implemented computationally, providing visual representations of the systems' evolution over time. The biome model illustrates the path to and consequences of bifurcation, while the torus simulation depicts the stages of deformation leading to structural break. This work contributes to the understanding of topological changes and critical transitions in both ecological and physical systems. By presenting these models in parallel, we highlight the universal nature of stability, bifurcation, and failure across different domains. The methodologies presented here have potential applications in ecology, materials science, structural engineering, and theoretical physics, offering a framework for studying the limits of system integrity under stress.

This manuscript presents a novel approach to estimating the potential within Schrödinger equations, with a particular focus on applications to the Navier-Stokes problem in fluid dynamics. By establishing new theoretical estimates, we delve into the intricate dynamics of fluid flow, aiming to unveil previously obscured aspects of the Navier-Stokes equations. Through a rigorous mathematical framework, we explore how these new potential estimates can provide a fresh perspective on fluid mechanics, contributing to the ongoing quest to solve some of its most persistent challenges.

Food systems will need to undergo considerable transformation. To be better prepared for and resilient to uncertainty and disturbances in the future, resource users and managers need to further develop knowledge about the food and farming system, with its dominating feedback structures and complexities, and to test robust and integrated system-based solutions. This paper investigates how participatory system dynamics modeling can be adapted to groups at the community level with low or no formal educational background. The paper also analyzes the refinement of workshop participants’ mental models as a consequence of a participatory system dynamics intervention. For this purpose, we ran two workshops with small-scale farmers in Zambia. Analysis of workshop data and post-workshop interviews shows that participatory system dynamics is well adaptable to support an audience-specific learning-by-doing approach. The use of pictures, objects and water glasses in combination with the basic aspects of causal loop diagramming makes for a well-balanced toolbox. Participants acquire understanding that is also relevant beyond systems thinking in that is offers a range of practical insights such as a critical evaluation of common food security strategies.

Maxwell equations governing electromagnetic effects are being shown to be equivalent to the compressible inviscid Navier-Stokes equations applicable in fluid dynamics and representing conservation of mass and linear momentum. The latter applies subject to a generalized Beltrami condition to be satisfied by the magnetic field. This equivalence indicates that the compressible inviscid Navier-Stokes equations are Lorentz invariant as they derive directly from the Lorentz invariant Maxwell equations subject to the same Beltrami condition. In addition, the derivation results provide support for the claim that electromagnetic potentials have physical significance as demonstrated by Aharonov-Bohm effect, and are not only a convenient mathematical formulation.

At the Atsumi Wind Farm in Aichi Prefecture, Japan, damage to wind turbines occurred frequently due to terrain-induced turbulence. In the present study, numerical analyses of terrain-induced turbulence were conducted by reproducing the topography in the vicinity of the wind turbine sites in high resolution and using RIAM-COMPACT natural terrain version, which is based on large eddy simulation (LES). The results of the diagnoses indicated that, in the case of south-easterly wind, terrain-induced turbulence is generated at a small terrain feature located upstream of Wind Turbine (WT) #2, which serves as the origin of the turbulence. At the Atsumi Wind Farm, a combination of the series of wind diagnoses and on-site operation experience led to a decision to adopt an "automatic shutdown program" for WTs #1 and #2. Here, "automatic shutdown program" refers to the automatic suspension of wind turbine operation upon the wind speed and direction meeting the conditions associated with significant effects of terrain-induced turbulence at a wind turbine site. The adoption of the "automatic shutdown program" has successfully resulted in a large reduction in the number of occurrences of wind turbine damage, thus, creating major positive economic effects. 1) a reduction in the repair costs by 9.322 million yen per year per wind turbine, 2) an increase in the availability factor by 8.05%, and 3) an increase in the capacity factor by 1.7%.

As the global population faces an increasing prevalence of physical disabilities, the challenge of motor rehabilitation has become increasingly urgent. Considering that approximately 15% of the global population lives with some form of disability, with a significant number having motor disa-bilities that greatly impact their quality of life, the integration of robotic technologies into rehabili-tation processes offers an opportunity for significant improvement in functional recovery and pa-tient autonomy. This analysis aims to evaluate the progress and challenges encountered in imple-menting robotic technology for the rehabilitation of patients with physical disabilities, highlighting the potential of emerging technologies such as exoskeletons, assisted training devices, and brain-computer interface systems in facilitating motor recovery. By examining relevant clinical studies, the analysis demonstrates the varied effectiveness of robotic therapies compared to traditional re-habilitation methods, while also highlighting the need for ongoing research to optimize care prac-tices and address challenges related to cost, accessibility, and treatment personalization. In con-clusion, robotic technologies represent a promising direction in motor rehabilitation, with the po-tential to revolutionize the care of patients with physical disabilities, significantly improving quali-ty of life and social integration.

The part of this article dealing with topological insulators and topological superconductors was first written about two years ago - the ideas in the part about the topological universe originated six years ago or more. It’s rather strange that I never put the two parts together in writing before. My belief in unification is unshakeable - I’ve been convinced for years that the universe must be composed of topology. Since Earth is part of the cosmos, entanglement means it must have topological materials. The reverse is also true: topological materials on Earth are well known to science - so in a unification, space and time inevitably possess topological composition. Topological materials (topological insulators, topological superconductors) can be less mystifying if they’re related to the paradigm-shifting deterministic view of quantum mechanics which is described in the universal topology (the “rubber-sheet geometry” of the cosmos): see my previous submission “Hypothesis of Quantum Gravity - Resulting from a Static, Topological Universe Resulting from the Positives and Negatives of the Steady State and Big Bang Theories" at https://www.preprints.org/manuscript/202105.0239/v1 (the first section of this present article is a quick summary of the relevant parts).

In recent years, applying deep learning to solve physics problems has attracted much attention. Data-driven deep learning methods produce operators that can learn solutions to the whole system of partial differential equations. However, the existing methods are only evaluated on simple flow equations (e.g., Burger's equation), and only consider the generalization ability on different initial conditions. In this paper, we construct CFDBench, a benchmark with four classic problems in computational fluid dynamics (CFD): lid-driven cavity flow, laminar boundary layer flow in circular tubes, dam flows through the steps, and periodic Karman vortex street. Each flow problem includes data with various boundary conditions, fluid physical properties, and domain geometries. Compared to existing datasets, the advantages of CFDBench are (1) comprehensive. It contains common physical parameters such as velocity, pressure, and cavity fraction. (2) realistic. It is very suitable for deep learning solutions of fluid mechanics equations. (3) challenging. It has a certain learning difficulty, prompting to find models with strong learning ability. (4) standardized. CFDBench facilitates a comprehensive and fair comparison of different deep learning methods for CFD. We make appropriate modifications to popular deep neural networks to apply them to CFDBench and enable the accommodation of more changing inputs. The evaluation on CFDBench reveals some new shortcomings of existing works and we propose possible directions for solving such problems.

We review a number of preconditioners for the advection-diffusion operator and for the Schur complement matrix which in turn constitute the building blocks for Constraint and Triangular Preconditioners to accelerate the iterative solution of the discretized and linearized Navier-Stokes equations. An intensive numerical testing is performed onto the driven cavity problem with low values of the viscosity coefficient. We devise an efficient multigrid preconditioner for the advection-diffusion matrix which, combined with the commuted BFBt Schur complement approximation, and inserted in a 2 x 2 block preconditioner, provides convergence of the GMRES method in a number of iteration independent of the meshsize for the lowest values of the viscosity parameter. The low-rank acceleration of such preconditioner is also investigated showing its great potential.

Titania is one of the most comprehensively studied nanostructures due to its widespread applications in production of catalytic, gas- sensing and corrosion- resistance materials [1]. M-polynomial of nanotubes has been vastly investigated as it produces many degree-based topological indices which are numerical parameters capturing structural and chemical properties. These indices are used in the development of quantitative structure-activity relationships (QSARs) in which the biological activity and other properties of molecules are correlated with their structure like boiling point, stability, strain energy etc of chemical compounds. In this paper, we determine M-polynomials of single-walled titanium (SW TiO2) nanotubes and recover important topological degree based indices of them to theoretically judge these nanotubes. We also use Maple to plot surfaces associated to different types of single-walled titanium (SW TiO2) nanotubes.

In the history of civil aircraft transportation, ice formation has been identifies as a key factor in the safety of flight. Anti-icing and deicing system have emerged through the years with the aim to prevent or to eliminate ice formation on wing airfoil, control surface and probes. Modern flying machine demand more efficiency in order to reduce the carbon footprint and increase the sustainability of flight transport. In order to achieve this goal the need to have efficient aircraft with efficient and low power consuming system is fundamental. This paper proposes a new model for ice accretion using computational fluid dynamics (CFD). This model permits to simulate the shape of the ice formed over a profile varying boundary conditions (i.e.- speed, liquid water content and so on). The proposed model takes into account also the amount of heat transferred between water and the surrounding environment and includes the effects of air turbulence on the ice formation process. The CFD simulations have been validated with NASA experimental outcome and show good agreement. The proposed model can be also used to investigate the effects of various parameters such as air speed, Liquid Water Content and air temperature on the ice formation process. The results evidences that the proposed model can accurately predict ice formation process and is suitable to optimize the design of anti-icing or deicing system for aircraft and helicopters. This approach is not limited to aerospace but can also be exported to other applications such as transportation, wind turbine, energy management and infrastructure.

M-polynomial of different molecular structures helps to calculate many topological indices. A topological index of graph G is a numerical parameter related to G which characterizes its molecular topology and is usually graph invariant. In the field of quantitative structure-activity (QSAR) quantitative structure-activity structure-property (QSPR) research, theoretical properties of the chemical compounds and their molecular topological indices such as the Zagreb indices, Randic index, Symmetric division index, Harmonic index, Inverse sum index, Augmented Zagreb index, multiple Zagreb indices etc. are correlated. In this report, we compute closed forms of M-polynomial, first Zagreb polynomial and second Zagreb polynomial of Octagonal network. From the M-polynomial we recover some degree-based topological indices for Octagonal network. Moreover, we give a graphical representation of our results.

The NW-SE trending dextral strike-slip faults on the north side of the Tian Shan play an important role in accommodating the crustal shortening, which mainly includes the Karatau fault, Talas-Fergana fault, Dzhalair-Naiman fault, Aktas fault, Dzhungarian fault (also named Bolokenu-Aqikekuduk fault) and Chingiz fault. The classic viewpoint is that the strike-slip fault is the adjustment product caused by the difference of the crustal shortening from west to east. Another viewpoint attributes the dextral strike-slip fault to large-scale sinistral shearing. The Alakol Lake Fault is situated along the northern margin of the Dzhungarian Gate, stretching for roughly 150 km from Lake Ebinur to Lake Alakol. Our team utilized aerial photographs, Satellite Stereo-imagery, and field observation to map the distribution of the Alakol Lake fault. Our findings provided evidence supporting the assertion that the fault is a dextral strike-slip fault. In reference to its spatial distribution, Lake Alakol is situated in a pull-apart basin that lies between two major dextral strike-slip fault lines: the Chingiz and Dzhungarian faults. The Alakol Lake Fault serves as a connecting point for these two faults, resulting in the formation of a mega NW-SE dextral strike-slip fault zone. According to our analysis of the dating samples taken from the alluvial fan, as well as our measurement of the displacement of the riser and gully, it appears that the Alakol Lake fault has a dextral strike-slip rate of 0.8-1.5mm/yr. The strike-slip rate of the Alakol Lake fault is comparatively higher than that of the Chingiz fault in the northern region (~0.7 mm/yr), but slower than that of the Dzhungarian fault in the southern (3.2-5 mm/yr). The Chingiz-Alakol-Dzhungarian fault zone shows a gradual decrease in deformation towards the interior of the Kazakhstan platform. We contend that the rate of deformation observed is better explained by the crustal shortening adjustment model, rather than the large-scale sinistral shearing model.

In this work, the analytical treatment of Fourth order pd equations has been discussed with the variational iteration algorithm with an auxiliary parameter. The technique has the capability of reducing the size of computational work and easily overcomes the difficulty of the perturbation method or Adomian polynomials. Comparison with the classic variational iteration algorithm- is carried out, showing that the modification is more efficient and reliable.

Catamaran hulls have always been associated with smaller vessels in naval engineering and construction. However, recent research results have shown that by considering specific criteria based on materiality, structure and functionality, they can be designed for a more complex industry, such as hydrofoil design. Among the challenges in this type of vessel, one of the most difficult variables is estimating the resistance to the advance in the function of the degree of uncertainty generated. This research focuses on optimising the drag of a sport sailing catamaran by implementing hydrofoils, through the application of computational fluid dynamics (CFD), at different speeds to demonstrate that it is possible to modify and improve the current appendages of this vessel.

The computing power of smartphones has not received considerable attention in the mainstream education system. Most of the education-oriented smartphone applications (apps) are limited to general purpose services like Massive Open Online Courses (MOOCs), language learning, and calculators (performing basic mathematical calculations). Greater potential of smartphones lies in educators and researchers developing their customized apps for learners in highly specific domains. In line with this, we present Fluid Dynamics, a highly accurate Android application for measuring flow properties in compressible flows. This app can determine properties across the stationary normal and oblique shock, moving normal shock and across Prandtl $-$ Meyer expansion fan. This app can also measure isentropic flows, Fanno flows, and Rayleigh flows. The functionality of this app is also extended to calculate properties in the atmosphere by assuming the International Standard Atmosphere (ISA) relations and also flows across the Pitot tube. Such measurements are complicated and time-consuming since the relations are implicit and hence require the use of numerical methods, which give rise to repetitive calculations. The app is an efficient semi-implicit solver for gas dynamics formulations and uses underlying numerical methods for the computations in a graphical user interface (GUI), thereby easing and quickening the learning of concerned users. The app is designed for the Android operating system, the most ubiquitous and capable surveillance platform, and its calculations are based on JAVA based code methodology. In order to check its accuracy, the app's results are validated against the existing data given in the literature.

The electronic properties of calcium intercalated graphite (CaC6) as a function of pressure are revisited using density functional theory (DFT). The electronic band structures of CaC6, like many other layered superconducting materials, display cosine-shaped bands at or near the Fermi level (FL). Such bands encompass bonding/antibonding information with a strong connection to superconducting properties. Using an hexagonal cell representation for CaC6, construction of a double supercell in the c-direction effects six-folding in reciprocal space of the full cosine function, explicitly revealing the bonding/antibonding relationship divide at the cosine midpoint. Similarly, folding of the Fermi surface (FS) reveals physical phenomena relevant to electronic topological transitions (ETT) with application of pressure. For CaC6, the peak value for the superconducting transition temperature, Tc, occurs at about 7.5 GPa, near to the observed pressure of the calculated ETT. At this pressure, the radius of the nearly spherical Ca 4s-orbital FS coincides with three times the distance from the G centre point to the Brillouin zone (BZ) boundary of the 2c supercell (which is equal to half the identically defined distance for the primitive rhombohedral BZ). In addition, the ETT coincides with alignment of the non-bonding (inflection) point of the cosine band (the point at which the sign of the cosine amplitude modulation is reversed) with the FL. At other calculated pressure conditions, the Ca 4s-orbital FS undergoes topological changes that correspond and can be correlated to experimentally determined changes in Tc. The ETT is a key mechanism that circumscribes the known significant drop in Tc for CaC6 as a function of increasing pressure.

Wood is poised to become a material of choice for future construction. When appropriately managed, it is a renewable material with unique mechanical properties. Beyond its inherent sustainability, the use of wood has a crucial role in addressing climate change concerns due a significantly lower energy consumption and emissions during manufacturing and transportation, while simultaneously acting as a carbon sink. Thus, there has been a growing demand for hardwoods for structural applications, including Castanea sativa Mill., the focal point of this investigation. Albeit in a limited capacity, Eurocode 5-2 offers friction coefficients for softwoods, but it falls short for hardwoods which it is a gap to bridge with this research. These coefficients play a critical role in numerical simulations involving friction, enabling the optimization of joints and, by extension, the overall structural integrity. Test samples were evaluated at 18% moisture content, which is typical of Service Class 2, for various orientations of timber-to-timber and timber-to-steel friction. Considering previous friction coefficients at 12% moisture content, the linear variation was evaluated at an intermediate value of 15%. The results provide an experimental database for numerical simulations and highlight the influence of moisture content on the coefficients, which increase linearly along moisture percentages.

Road vehicles are a large contributor to Nitrogen Oxides (NOx) pollution. The routine road-side monitoring stations, however, may underrepresent the severity of personal exposure in urban areas, because long-term average readings cannot capture the effects of momentary, high peaks of air pollution. While numerical modelling tools historically have been used to propose an improved distribution of monitoring stations, ultra-high resolution Computational Fluid Dynamics models can further assist the relevant stakeholders in understanding the important details of pollutant dispersion and exposure at local level. This study deploys a 10 cm-resolution CFD model to evaluate actual high peaks of personal exposure to NOx from traffic, by tracking the gases emitted from the tailpipe of moving vehicles being dispersed towards the roadside. The investigation shows that a set of four Euro 5-rated diesel vehicles travelling at constant speed may generate momentary road-side concentrations of NOx as high as 1.25 mg/m3, with 25% expected increase for doubling the number of vehicles and approximately 50% reduction when considering Euro 6-rated vehicles. The paper demonstrates how the numerical tool can be used to identify the impact of measures to reduce personal exposure, such as protective urban furniture, as traffic patterns and environmental conditions change.

Basaltic activity is the most common class of volcanism on Earth, characterized by magmas of sufficiently low viscosities such that bubbles can move independently of the melt. Following exsolution, spherical bubbles can then expand and/or coalesce to generate larger bubbles of spherical-cap or Taylor bubble (slug) morphologies. Puffing and strombolian explosive activity are driven by bursting of these larger bubbles at the surface. Here, we present the first combined model classification of spherical-cap and Taylor bubble driven puffing and strombolian activity modes on volcanoes. We furthermore incorporate the possibility that neighboring bubbles might coalesce, leading to elevated strombolian explosivity. The model categorizes behavior in terms of the temporal separation between the arrival of successive bubbles at the surface and bubble gas volume or length, with the output presented on visually intuitive two-dimensional plots. The categorized behavior is grouped into the following regimes: puffing from a) cap bubbles; and b) non-overpressurised Taylor bubbles; and c) Taylor bubble driven strombolian explosions; each of these regimes is further subdivided into scenarios whereby inter-bubble interaction does/doesn't occur. The model performance is corroborated using field data from Stromboli (Aeolian Islands, Italy), Etna (Sicily, Italy) and Yasur (Vanuatu), representing one of the very first studies, focused on combining high temporal resolution degassing data with fluid dynamics, as a means of deepening our understanding of the processes which drive basaltic volcanism.

In the present study, a numerical model was developed to predict the flow pattern inside a broiler building. The model intends to predict the velocities fields inside the domain and ammonia (NH3) emitted or released by litter from poultry housing. The numerical model developed in Computational Fluid Dynamics (CFD) commercial code, intends to represent a commercial broiler building, and intends to simulate the 3D and heat transfer, in steady state flow. The evaporative cooling pads were also included in the model. The validation of the model was based in experimental measurements obtained in previous studies. The simulations were focused on Summer, Winter and also Mid-Season situation. The numerical results of NH3 concentration were compared with the experimental measurements, and a quite good agreement was verified. The numerical results allowed the characterization of: the inside flow pattern developed for the summer and winter situation; the inside NH3 distribution, and the velocity field distribution inside the broiler building. It was found that NH3 concentration increases along the tunnel, especially in low flow rate imposed from the exhaust fan. Also, it was verified that the low velocities inside domain are no sufficient to remove the gaseous pollutants.

Existing Reynolds Averaged Navier-Stokes based transition models do not accurately predict separation induced transition for low pressure turbines. Therefore, in this study, a novel framework based on computational fluids dynamics driven machine learning coupled with multi-expression and multi-objective optimization is explored to develop models which can improve the transition prediction for the T106A low pressure turbine at an isentropic exit Reynolds number of Re2is=100,000. Model formulations are proposed for the transfer and laminar eddy viscosity terms of the laminar kinetic energy transition model using seven non-dimensional pi groups. The multi-objective optimization approach makes use of cost functions based on the suction-side wall-shear stress and the pressure coefficient. A family of solutions is thus developed, whose performance is assessed using Pareto analysis and in terms of physical characteristics of separated-flow transition. Two models are found which bring the wall-shear stress profile in the separated region at least two times closer to the reference high-fidelity data than the baseline transition model. As these models are able to accurately predict the flow coming off the blade trailing edge, they are also able to significantly enhance the wake-mixing prediction over the baseline model.

We study the coupling of two topologcal subsystems in distinct topological states, and show that it leads to a precursor behavior of the topological phase transition in the overall system. This behavior is solely determined by the symmetry classes of the subsystem Hamiltonians and coupling terms, and is marked by the persistent existence of subgap states within the bulk energy gap. By investigating the critical current of Josephson junctions involving topological superconductors, we also illustrate that such subgap states play crucial roles in physical properties of nanoscale devices or materials.

The current study presents a computational fluid dynamics model designed to simulate the isolation of 2D graphene components from their dispersion using a microfiltration hollow fiber membrane unit. The model utilizes Navier-Stokes and mass conservation equations to predict the flow and concentration behaviors in the system, and it employs the resistance-in-series approach to couple the fouling of the non-exfoliated graphites in the dispersion to the model. Specifically, the model accounts for the effects of the concentration polarization and cake formation of the fouling component, resulting in the increment of the transmembrane pressure (TMP) of the system. Additionally, we assumed the wettability of polymeric membrane’s inner wall enhances upon fouling by the flat layered structure material, leading to the reduction of the transmemrabe pressure. This approach demosntrates accurate reproduction of the exceptional experimental TMP behavior corresponding to the fouling of the graphite.

This paper proposes a procedure for predicting the actual wind speed for flow over complex terrain with CFD. It converts a time-series of wind speed data acquired from field observations into a time-series of actual scalar wind speed by using non-dimensional wind speed parameters which are determined beforehand with the use of CFD output. The accuracy and reproducibility of the prediction procedure were examined by simulating the flow with CFD with the use of high resolution (5 m) surface elevation data for the Noma Wind Park in Kagoshima Prefecture, Japan. The errors of the predicted average monthly wind speeds relative to the observed values were less than approximately 20%.

This review paper provides an overview of recent advances in computational fluid dynamics (CFD) simulations of ejector pumps for vacuum generation. It examines various turbulence models, multiphase flow approaches, and numerical techniques employed to capture complex flow phenomena like shock waves, mixing, phase transitions, and heat/mass transfer. Emphasis is placed on comprehensive assessment of flow characteristics within ejectors, including condensation effects such as nucleation, droplet growth, and non-equilibrium conditions. The review highlights efforts in optimizing ejector geometries and operating parameters to enhance the entrainment ratio, a crucial performance metric for ejectors. The studies reviewed encompass diverse working fluids, flow regimes, and geometric configurations, underscoring the significance of ejector technology across various industries. While substantial progress has been made in developing advanced simulation techniques, several challenges persist, including accurate modeling of real gas behavior, phase change kinetics, and coupled heat/mass transfer phenomena. Future research efforts should focus on developing robust multiphase models, implementing advanced turbulence modeling techniques, integrating machine learning based optimization methods, and exploring novel ejector configurations for emerging applications.

Backgroumd: The feeling of nasal obstruction is one of the most complaints of the Ear Nose and Throats (ENT) patients. The reason of this complaint is variable, such as Nasal Septal Deviation (NSD). NSD is a significant obstacle to normal respiration and the volume of air entering the lungs. Understanding how the deviation causes the obstruction is so important, because it leads to better management of this disease. Rhinomanometry and acoustic rhinometry are methods that are used for objective evaluation of upper airway, but they are semi invasive and the accuracy are not guaranteed. With development of Computed Tomography (CT scan) and Computational Fluid Dynamics (CFD), numerical studies on airflow in different parts of the nasal cavity have been performed. Objectives: The purpose of this study was to compare nasal airflow patterns between patient with NSD and healthy nasal cavity using a computational fluid dynamics (CFD) Methods: A patient with NSD and a healthy human were selected. Using CFD, the maximal airflow velocity, nasal resistance, maximal Wall Shear Stress (WSS), and pressure drop in bilateral nostrils of both cases were assessed. Results: Pressure and velocity profiles are evaluated at a mass flow rate of 17.4 Liters Per Minute (LPM). The velocity profile shows an abnormal flow profile in the septal deviated nasal cavity and the peak velocity is observed at the middle nasal region, whereas this point is at the nasal valve level in a healthy nasal cavity. Wall shear stress (WSS) caused by NSD is lower than in normal nasal cavities. The pressure drop in a nasal cavity with deviated septum is higher than in a healthy nasal cavity. Based on the results of this investigation nasal resistance in NSD was higher than in normal, healthy nasal cavity. Conclusions: NSD plays an important role in nasal airflow regime and it results in the feeling of obstruction comparing to normal nasal cavity. Also there is a promising future for CFD to become a useful tool in understanding airflow physiology and pathology.

People have always hoped to be able to fill an entire plane with ``single unit cells'' without periodicity. This wish was realized after the mathematician discovered a 13-sided ``single unit cell'' named `einstein'. These non-periodic tessellations generally exhibit anisotropic properties, making them superior in terms of mechanical performance compared to periodic structures. From the perspective of information entropy, the reason behind the improved mechanical properties of these structures is the higher entropy associated with non-periodic configurations. To quantify the disorder of non-periodic structures, we propose an entropy expression for the `einstein' metamaterial. To demonstrate the mechanical properties of these high-entropy structures, we fabricate specimens using 3D printing and conducte mechanical experiments. For comparative analysis, we also use ABAQUS to perform finite element analysis of the problem. The research results reveal that the mechanical properties of high-entropy structures created by the non-periodic stacking of cells are significantly improved compared to those of low-entropy structures created by periodic stacking. The conclusions drawn from the study of individual issues are generalizable and may be of assistance in future material and structural design.

The emergence of electric vehicles has brought new issues such as the problem of rolling element bearings (REBs) operating at high speeds. Losses due to these components in mechanical transmissions are a key issue and must therefore be taken into account right from the design stage of these systems. Among these losses, the one induced by the motion of rolling elements , known as drag loss, becomes predominant in high-speed REBs. Although an experimental approach is still possible, it is difficult to isolate this loss in order to study it properly. A numerical approach based on CFD is therefore a possible way forward, even if other issues arise. The aim of this article is to study the ability of such an approach to correctly estimate the drag coefficient associated with the motion of rolling elements. The influence of the numerical domain extension, the mesh refinement, the simplification of the ring shape and the presence of the cage, on the values of the drag coefficient is presented. While it seems possible to compromise on the calculation domain and mesh size, it appears that the other parameters must be taken into account as much as possible to obtain realistic results.

The automotive industry has witnessed a significant push towards increased fuel efficiency and reduced carbon emissions. Among many factors influencing overall vehicle efficiency, aerodynamic drag is a critical consideration, accounting for a substantial portion of fuel consumption. Our investigation focused on the drag coefficients of three prominent 2023 passenger car models – the Toyota Corolla, Hyundai Elantra, and Kia Soul. Using ANSYS Fluent to perform computational fluid dynamics, we demonstrated an inverse correlation between drag force and gas mileage, underlining the significance of aerodynamic design in fuel efficiency. Notably, the Hyundai Elantra emerged as the most aerodynamically efficient of the three vehicles, followed closely by the Toyota Corolla. In contrast, the boxier-designed Kia Soul exhibited significantly higher drag coefficients and drag forces, rendering it the least efficient of the trio. These findings emphasize the importance of environmental factors in car design. Shaping aerodynamic profiles directly impacts fuel efficiency, stability, and overall performance.

This study proposes a customized industrial nozzle for generating impulsive air jets. It is installed on an automatic machine where wine caps are stacked and shot consecutively into a rotating cylinder by an air jet. This process is very noisy; hence, this study aimed to investigate possible geometric variations of the nozzle that can reduce the emitted noise. First, the nozzle was tested in a laboratory to measure the air consumption at different supply pressures. Subsequently, 3D models of the nozzle and its variations were created and used for computational fluid dynamics simulations. Different boundary conditions were set, first to validate the model and compare it with the experimental test results, and then to simulate the real working conditions and determine the geometry that is less noisy while maintaining the velocity peak. Among the various possibilities, shortening the final ducts of the nozzle appears to be the most promising solution. These modified nozzles could be easily added to current machines to provide immediate benefits, and this study represents a promising start for action on other machines where this type of device is present.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

The efficiency of organic solar cells (OSCs) is influenced by various factors, among which environmental temperature plays a significant role. Previous studies have shown that the thermal stability of these cells can be enhanced by incorporating a third component into their structure. Ternary organic solar cells, in particular, have shown promising results in improving thermal stability. A well-designed electron transport layer (ETL) can significantly bolster thermal stability by facilitating efficient charge transport and reducing charge recombination. In this study, we investigated the effect of temperature on the efficiency of inverted ternary structures, ranging from 300 K to 400 K. The structures examined include FTO/SnO2/PM6:D18:L8-BO/PEDOT: PSS/Ag, FTO/Spiro-OMeTAD/PM6:D18:L8-BO/PEDOT: PSS/Ag, and FTO/PC60BM/PM6:D18:L8-BO/PEDOT: PSS/Ag. Through simulations employing three different electron transport layers—SnO2, Spiro-OMeTAD, and PC60BM—we observed that at 340 K (65°C) these structures maintained 92% of their original high efficiency of ~20% at 300 K, which represents a high level of thermal stability under the high PCE condition.

We recently proposed that topological quantum computing might be based on $SL(2,\mathbb{C})$ representations of the fundamental group $\pi_1(S^3\setminus K)$ for the complement of a link $K$ in the $3$-sphere. The restriction to links whose associated $SL(2,\mathbb{C})$ character variety $\mathcal{V}$ contains a Fricke surface $\kappa_d=xyz -x^2-y^2-z^2+d$ is desirable due to the connection of Fricke spaces to elementary topology. Taking $K$ as the Hopf link $L2a1$, one of the three arithmetic two-bridge links [the Whitehead link $5_1^2$, the Berge link $6_2^2$, the double-eight link $6_3^2$] or the link $7_3^2$, the $\mathcal{V}$ for those links contains the reducible component $\kappa_4$, the so-called Cayley cubic. In addition, the $\mathcal{V}$ for the later two links contains the irreducible component $\kappa_3$, or $\kappa_2$, respectively. Taking $\rho$ to be a representation with character $\kappa_d$ ($d<4$), with $|x|,|y|,|z| \le 2$, then $\rho(\pi_1)$ fixes a unique point in the hyperbolic space $\mathcal{H}_3$ and is conjugate to a $SU(2)$ representation (a qubit). Even though details on the physical implementation remain open, more generally, we show that topological quantum computing may be developed from the point of view of three-bridge links, the topology of the $4$-punctured sphere and Painlev\'e VI equation. The $0$-surgery on the $3$ circles of the Borromean rings L6a4 is taken as an example.

During HIV-1 virus assembly the genomic RNA (vRNA) is selected for packaging by the viral protein Gag because it contains a specific packaging signal, Psi. While there have been numerous studies of Gag-Psi interactions, there is almost no information on kinetic aspects of this interaction. We have investigated the kinetics of Gag binding to different RNAs using switchSENSE DRX2 technology. We measured the association rate of Gag binding to monomeric Psi, to a “Multiple Binding Site Mutant” Psi that is inactive for genome packaging in vivo, and to a scrambled Psi. We discovered that Gag binds more rapidly to Psi RNA than to the mutant or scrambled RNAs. Furthermore, rapid Gag association kinetics are retained within sub-regions of Psi: Gag associates more rapidly with RNA containing only the 3’ two of the three Psi stem-loops than with monomeric RNA containing the 5’ two stem-loops or a scrambled RNA. No differences were detectable with individual Psi stem-loops. Interestingly, the rate of binding of Gag molecules to Psi increases with increasing Gag concentration, suggesting cooperativity in binding. The results are consistent with the hypothesis that selectivity in packaging derives from kinetic differences in initiation of particle assembly.

We study the Kelvinons: monopole ring solutions to the Euler equations, regularized as the Burgers vortex in the viscous core. There is finite anomalous dissipation in the inviscid limit. However, in the anomalous Hamiltonian, some terms are growing as logarithms of Reynolds number; these terms come from the core of the Burgers vortex. In our theory, the turbulent multifractal phenomenon is similar to asymptotic freedom in QCD, with these logarithmic terms summed up by an RG equation. The small effective coupling does not imply small velocity; on the contrary, velocity is large compared to its fluctuations, which opens the way for a quantitative theory. In the leading order in the perturbation theory in this effective coupling constant, we compute running multifractal dimensions for high moments of velocity circulation, in good agreement with the data for quantum Turbulence and available data for classical Turbulence. The logarithmic dependence of fractal dimensions on the loop size comes from the running coupling in anomalous dimensions. This slow logarithmic drift of fractal dimensions would be barely observable at Reynolds numbers achievable at modern DNS.

We have developed an unsteady and non-linear wind synopsis simulator called RIAM-COMPACT (Research Institute for Applied Mechanics, Kyushu University, COMputational Prediction of Airflow over Complex Terrain) in order to simulate the airflow on a microscale, i.e., a few tens of km or less. In RIAM-COMPACT, the large-eddy simulation (LES) has been adopted for turbulence modeling. LES is a technique in which the structures of relatively large eddies are directly simulated and smaller eddies are modeled using a sub-grid scale model. In the present study, we have conducted the numerical wind diagnoses for Taikoyama Wind Farm nacelle separation accident in Japan. The simulation results suggest that all six wind turbines at the Taikoyama Wind Farm are subject to significant influence from separated flow (terrain-induced turbulence) which is generated due to the topographic irregularities in the vicinity of the wind turbines. A proposal has been also made on reconstruction of the wind farm.

The main objective of this work is to investigate the temporal variation of PM10 concentrations within the urban area of Athens during the years 2001-2015. For this purpose, the time series of the particulate matter with aerodynamic diameter less than 10μm (PM10) is recorded for a 15-year period (2001-2015) in two different monitoring stations located in the urban area of Athens. The results show a totally different behavior of PM10 concentrations between the Athens city center and the suburban areas. It seems that in the city center the main sources of PM10 are traffic and heating systems especially during the cold period of the year. Furthermore, in the city center a significant seasonal variation was found with high concentrations during the cold period of the year and lower concentrations during the warm period of the year. Moreover, it was found that during the weekends, there is a decrease in PM10 concentrations probably due to the fact that majority of people do not use their vehicles. Finally, for both locations a significant temporal decreasing trend of the mean annual PM10 concentrations was found which indicates that during the last years, there have been improvements towards a better air quality.

The combination of artificial intelligence algorithms and numerical methods has recently become popular in the prediction of macroscopic and microscopic hydrodynamics parameters of bubble column reactors. The multi inputs and outputs machine learning can cover small phase interactions or large fluid behavior in industrial domains. This numerical combination can develop the smart multiphase bubble column reactor with the ability of low-cost computational time. It can also decrease case studies for the optimization process when big data is appropriately used during learning. There are still many model parameters that need to be optimized for a very accurate artificial algorithm, including data processing and initialization, the combination of inputs and outputs, number of inputs and model tuning parameters. For this study, we aim to train four inputs big data during learning process by an adaptive neuro-fuzzy inference system or adaptive-network-based fuzzy inference system (ANFIS) method, and we consider the superficial gas velocity as one of the input variables, while for the first time, one of the computational fluid dynamics (CFD) outputs named gas velocity is used as an output of the artificial algorithm. The results show that the increasing number of input variables improves the intelligence of the ANFIS method up to , and the number of rules during learning process has a significant effect on the accuracy of this type of modeling. The results also show that propper selection of model parameters results in more accuracy in prediction of the flow characteristics in the column structure.

Stueckelberg-Horwitz-Piron (SHP) electrodynamics formalizes the distinction between coordinate time (measured by laboratory clocks) and chronology (temporal ordering) by defining 4D spacetime events x^μ as functions of an external evolution parameter τ. Classical spacetime events x^μ (τ) evolve as τ grows monotonically, tracing out particle worldlines dynamically and inducing the five U(1) gauge potentials through which events interact. Since Lorentz invariance imposes time reversal symmetry on x⁰ but not τ, the formalism resolves grandfather paradoxes and related problems of irreversibility. The action involves standard first order field derivatives but includes a higher order τ derivative that while preserving gauge and Lorentz invariance removes certain singularities and makes the related QFT super-renormalizable. The resulting field equations are Maxwell-like but τ-dependent and sourced by a current that represents a statistical ensemble of instantaneous events distributed along the worldline. The width λ of this distribution defines a correlation time for the interactions and a mass spectrum for the photons that carry the interaction. As λ becomes very large, the photon mass goes to zero and the field equations become τ-independent Maxwell’s equations. Maxwell theory thus emerges as an equilibrium limit of SHP, in which λ is larger than any other relevant time scale. Particles and fields are not constrained to mass shells in SHP theory, and by exchanging mass may produce pair creation/annihilation processes at the classical level. On-shell evolution with fixed particle masses is restored through a self-interaction associated with the 5D wave equation.

In this paper we introduce a computational model for the simulation of hypervelocity impact (HVI) phenomena which is based on the Discrete Element Method (DEM). Our paper constitutes the first application of DEM to the modeling and simulating of impact events for velocities beyond 5 kms⁻¹. We present here the results of a systematic numerical study on HVI of solids. For modeling the solids, we use discrete spherical particles that interact with each other via potentials. In our numerical investigations we are particularly interested in the dynamics of material fragmentation upon impact. We model a typical HVI experiment configuration where a sphere strikes a thin plate and investigate the properties of the resulting debris cloud. We provide a quantitative computational analysis of the resulting debris cloud caused by impact and a comprehensive parameter study by varying key parameters of our model. We compare our findings from the simulations with recent HVI experiments performed at our institute. Our findings are that the DEM method leads to very stable, energy–conserving simulations of HVI scenarios that map the experimental setup where a sphere strikes a thin plate at hypervelocity speed. Our chosen interaction model works particularly well in the velocity range where the local stresses caused by impact shock waves markedly exceed the ultimate material strength.

Objective: The stability of the flight phase in ski jumping is crucial for athletes' performance and safety. This study aims to investigate the influence of unfavorable conditions on aerodynamic characteristics and flight stability through computational fluid dynamics (CFD) numerical simulations. Methods: The ski jumper and the skis are considered as a multi-body system. A detailed three-dimensional (3D) model of this multi-body system under a commonly observed posture during flight is established. The partially averaged Navier-Stokes (PANS) turbulence model is employed, and CFD simulations are conducted to predict the aerodynamic characteristics of the multi-body system under lateral environmental wind and asymmetric postures during flight phase. The conditions of asymmetric postures include yaw rotation and roll rotation. Results: (1) Lateral environmental wind generated yaw force, yaw moment, and roll moment, which influenced the lift, drag, and pitch moment of the athlete. These forces and moments were relatively small at lower wind speeds (less than 3 m/s) and became more significant at higher wind speeds (greater than 4.5 m/s). (2) Under the influence of yaw rotation or roll rotation, the multi-body system exhibited noticeable yaw force, yaw moment, and roll moment, all showing a monotonic increasing trend. Moreover, they had a significant impact on the lift, drag, and pitch moment of the multi-body system. Conclusion: (1) The influence of unfavorable conditions is complex, resulting in significant yaw force, yaw moment, and roll moment on the multi-body system. The adverse effects of roll rotation were generally greater than those of yaw rotation. (2) The multi-body system exhibited self-stabilizing tendencies in yaw and roll. This phenomenon can provide a solution to maintain flight stability by employing appropriate yaw or (and) roll rotation angles, effectively compensating for or even eliminating the adverse effects of lateral environmental wind. (3) Understanding the mechanisms of how unfavorable conditions affect the aerodynamic characteristics and stability during flight in ski jumping can provide valuable assistance for real-time prediction and decision-making during competitions, as well as scientific guidance for training athletes stable flight control and techniques and improving their sport performance.

In this paper, a numerical modeling of the impact, spreading, and eventually rebound of a viscoelastic droplet is reported. The numerical model is based on the volume of fluid (VOF) method coupled with the FENE-CR constitutive equations, and accounts for both the surface tension and the substrate wettability. The FENE-CR constitutive equations are used to model the polymer solution, while taking advantage of its rheological characterization. The comparison is performed between droplets of Newtonian solvent and a monodisperse polymer solution. The droplet impact on both hydrophilic and superhydrophobic substrate is analyzed through a detailed analysis of the spreading diameter evolution. It is found that while the droplet kinematic phase seems independent of the substrate and fluids properties, the recoiling phase is highly related to all of them. In addition, the model infers a critical polymer concentration above which the droplet rebound from a superhydrophobic substrate is suppressed. The simulation is of particular interest to ink-jet processing, and demonstrates the capability of the model to handle complex non-Newtonian droplet dynamics.

Topological indices are invariant numerical fields of a graph that give facts about the structure of graphs and are found to be very helpful in predicting the physical properties of aluminophosphates. The characteristics of the aluminophosphates are similar to those of zeolites. Two examples of current applications are natural gas dehydration and humidity sensor. New frameworks are being synthesised by researchers in chemistry and materials science. There are many layers and holes in these substances. In this study, Vertex version of distance-based topological indices, the entropy of topological indices and their numerical analysis are explained.

The main objective of this study is to demonstrate proof of principle that computational fluid dynamics (CFD) modeling is a tool for studying the contribution of covert and overt vascular architecture to the risk of cerebrovascular disease in in sickle cell disease (SCD) as well as uncover one or more mechanism of response to therapy such as chronic red blood cell (cRBC) transfusion. We analyzed baseline (screening), pre-randomization and study exit magnetic resonance angiogram (MRA) images from 10 (5 each from the transfusion and observation arms) pediatric sickle SCD participants in the silent cerebral infarct transfusion (SIT) trial, using CFD modeling. We reconstructed the intracranial portion of the internal carotid artery and branches and extracted the geometry using 3D Slicer. We cut specific potions of the large intracranial artery to include segments of the internal carotid, middle, anterior, and posterior cerebral artery such that the vessel segment analyzed extended from the intracranial beginning of the internal carotid artery up to immediately after (~0.25 inches) the middle cerebral artery branching point. Cut models were imported into Ansys 2021R2/2022R1 and laminar and time-dependent flow simulation was performed. Change in time averaged mean velocity, wall shear stress, and vessel tortuosity were compared between the observation and cRBC arm. We did not observe a correlation between time averaged mean velocity (TAMV) and mean transcranial doppler (TCD) velocity at study entry. There was also no difference in change in time average mean velocity, wall shear stress (WSS), and vessel tortuosity between the observation and cRBC transfusion arms. WSS and TAMV were abnormal for 2 (developed TIA) out of the 3 participants (one participant had SCI) that developed neurovascular outcomes. CFD approaches allows for the evaluation of vascular topology and hemodynamics in SCD using MRA images. In this proof of principle study, we show that CFD could be a useful tool and we intend to carry out future studies with a larger sample to enable more robust conclusions.

The experimental realization of twisted bilayer graphene strongly pushed the inspection of bilayer systems. In this context, it was recently shown that a two layer Haldane model with a thirty degree rotation angle between the layers represents a higher order topological insulator, with zero-dimensional states isolated in energy and localized at the physical vertices of the nanostructure. We show, within a numerical tight binding approach, that the energy of the zero dimensional states strongly depends on the geometrical structure of the vertices. In the most extreme cases, once a specific band gap is considered, these bound states can even disappear just by changing the vertex structure.

While the observation of magnetic monopoles has defied all experimental attempts in high-energy physics and astrophysics, sound theoretical approaches predict they should exist, and they have indeed been observed as quasiparticle excitations in certain condensed-matter systems. This indicates that, even though they are not ubiquitous contrary to electrons, it is possible to get them as excitations above a ground state. In this report, we show that phonons or lattice shear strain generate topological monopoles in some low-dimensional quantum antiferromagnets. For the Heisenberg ladder, phonons are found to generate topological monopoles with nonzero density due to quantum spin fluctuations. For the four-leg Heisenberg tube, longitudinal shear stress generates topological monopoles with density proportional to the strain deformation. The present theory is based on mapping the spin degrees of freedom onto spinless fermions using the generalized Jordan-Wigner transformation in dimensions higher than one. The effective magnetic field generated by the motion of the spinless fermions has non-zero divergence when phonons or shear stress are present. A possible system where the present kind of monopoles could be observed is BiCu$_2$PO$_6$.

In this paper, it is introduced the notion of r-fuzzy β-T_i, i = 0, 1, 2 separation axioms related to a fuzzy operator β on the initial set X which is a generalization of previous fuzzy separation axioms. An r-fuzzy α-connectedness related to a fuzzy operator α on the set X is introduced which is a generalization of many types of r-fuzzy connectedness. An r-fuzzy α-compactness related to a fuzzy operator α on the set X is introduced which is a generalization of many types of fuzzy compactness.

We will apply Pascal’s hydrostatic pressure law to black holes and also to the Hubble sphere. Haug has recently demonstrated how hydrostatic pressure in water can be utilized to determine the Planck length. One can conceptualize the energy in the Hubble sphere as a type of superfluid, and if this is correct, then Blaise Pascal’s hydrostatic pressure formula may also be applicable to such a superfluid, even within the Hubble sphere. By employing the same method on the Hubble sphere and considering it as a Schwarzschild black hole with the critical Friedmann mass, we can estimate the Planck length based on its hypothetical hydrostatic pressure.

The most important plastic resins used for wire coating are Polyvinyl Chloride (PVC), Nylon, Polysulfone and Low-high density polyethylene (LDPE / HDPE). In this article,the coating process is performed using elastic-viscous fluid as a coating material for wire coating in a pressure type coating die. The elastic-viscous fluid is electrically conducted in the presence of an applied magnetic field. The governing non-linear equations are modeled and then solved analytically by utilizing an Adomian decomposition method (ADM). The convergence of the series solution is established. The results are also verified by Optimal Homotopy Asymptotic Method (OHAM). The effect of different emerging parameters such as non-Newtonian parameters α and β, magnetic parameter M and the Brinkman number Br on solutions (velocity and temperature profiles) are discussed through several graphs. Additionally, the current result also compares with the published work already available in the literature.

This work aims to generate some types of M_(j )–neighborhoods. Relationships among these M_(j )-neighborhoods and some other types of neighborhoods are discussed. Additionally, M_(j )-lower, M_(j )-upper approximations and M_(j )-accuracy in terms of M_(j )-neighborhoods are presented. Their properties, with some examples, are investigated. Finally, We addressed the comparisons among M_(j )approach and other approaches.

Recently two new degree concepts have been defined in graph theory: ev-degree and ve-degree. Also the ev-degree and ve-degree Zagreb and Randić indices have been defined very recently as parallel of the classical definitions of Zagreb and Randić indices. It was shown that ev-degree and ve-degree topological indices can be used as possible tools in QSPR researches . In this paper we define the ve-degree and ev-degree Narumi–Katayama indices, investigate the predicting power of these novel indices and extremal graphs with respect to these novel topological indices. Also we give some basic mathematical properties of ev-degree and ve-degree Narumi-Katayama and Zagreb indices.

The dynamics of a spherical particle in an asymmetric serpentine is studied by finite element method (FEM) simulations in a physically unconstrained system. The two-way coupled time dependent solutions illustrate the path of the particle along a curve where a secondary flow (Dean flow) has developed. The simulated conditions were adjusted to match those of an experiment for which particles were focused under inertial focusing conditions. The obtained rotational modes allowed to infer the influence of the local flow around the particle. We propose a new approach to find the decoupled secondary flow contribution employing a quasi-Stokes flow.

Mammarenavirus Wenzhouense (WENV) is broadly distributed in Asia, while the he dynamics process of WENV infection remains unclear. A field derived strain of WENV was used to inoculate Sprague-Dawley (SD) rats by intramuscular injection, the process of virus infection was de-tected by controlling time for 28 days. Viral RNA became detectable in the blood at 3 d pi, and remained detectable for about 12 d. In most organ tissues, viral RNA peaked at 7 d pi, then began to decline by 14 d, however remained detectable in intestine and brain tissues at 21 and 28 d pi. Virus shedding had been detected from fecal samples for 5 days from 6 to 11 d pi using qRT-PCR, and was recovered from feces collected at 8 d pi. Horizontal contact infection occurred among cage-mates at 14 and 21 d pi. Antibodies against the nucleocapsid were detected at 5 dpi, next increased and persisted until the end of experiment. The results enabled to discriminate the kinetic of viremic response, virus shedding in feces and horizontal transmission, as well as the potential sites for WENV replication or maintenance of the virus in nature.

The oscillating heat pipe (OHP) is a new member in the family of heat pipes, and it has great potential applications in energy conservation. However, the fluid flow and heat transfer in the OHP as well as the fundamental effects of inner diameter on them have not been fully understood, which are essential to the design and optimization of the OHP in real applications. Therefore, by combining the high-speed visualization method and infrared thermal imaging technique, the fluid flow and thermal performance in the OHPs with inner diameters of 1, 2 and 3 mm are presented and analyzed. The results indicate that three fluid flow motions, including small oscillation, bulk oscillation and circulation, coexist or, respectively, exist alone with the increasing heating load under different inner diameters, with three flow patterns occurring in the OHPs, viz. bubbly flow, slug flow and annular flow. These fluid flow motions are closely correlated with the heat and mass transfer performance in the OHPs, which can be reflected by the characteristics of infrared thermal images of condensers. The decrease in the inner diameter increases the frictional flow resistance and capillary instability while restricting the nucleate boiling in OHPs, which leads to a smaller proportion of bubbly flow, a larger proportion of short slug flow, a poorer thermal performance, and easier dry-out of working fluid. In addition, when compared with the 2 mm OHP, the increasing role of gravity induces the thermosyphon effect and weakens the 'bubble pumping' action, which results in a little smaller and bigger thermal resistances of 3 mm OHP under small and bulk oscillation of working fluid, respectively.

In patients with heart failure, the evaluation of left ventricular (LV) diastolic function is vital, offering crucial insights into hemodynamic impact and prognostic accuracy. Echocardiography stands as the primary imaging modality for diastolic function assessment, and using it effectively requires a profound understanding of the underlying pathology. This review covers four main topics: first, the fundamental driving forces behind each phase of normal diastolic dynamics, along with the physiological basis of two widely used echocardiographic assessment parameters, E/e' and mitral annulus early diastolic velocity (e'); second, the intricate functional relationship between the left atrium and LV in patients with varying degrees of LV diastolic dysfunction (LVDD); third, the role of stress echocardiography in diagnosing LVDD and the significance of parameter changes in this context; and fourth, the clinical utility of evaluating diastolic function from echocardiography images across diverse cardiovascular care areas.

Starting from unidentified objects moving inside a two-dimensional Euclidean manifold, we propose a simple method to detect the topological changes that occur during their reciprocal interactions and shape morphing. This method, which allows the detection of topological holes development and disappearance, makes it possible to solve the uncertainty due to disconnectedness, lack of information and absence of objects’ sharp boundaries, i.e., the three troubling issues which prevent scientists to select the required proper sets/subsets during their experimental assessment of natural and artificial dynamical phenomena, such as fire propagation, wireless sensor networks, migration flows, neural networks’ and cosmic bodies’ analysis.

The landscape of business intelligence (BI) is marked by rapid growth, extensive research, and practical implementations, reflecting its sustained relevance in modern business strategies. This paper delves into the dynamics of BI, particularly focusing on the interplay between maturity and agility. While BI maturity emphasizes optimization and predefined goals, BI agility prioritizes adaptability and response to change. The paper highlights the contradictions between these concepts, emphasizing the need for a balanced approach in BI strategy formulation.The role of organizational culture in fostering BI agility is explored through literature review and interviews with BI professionals. Key insights include the necessity of an open culture for effective BI utilization, clear strategic vision, decision delegation, information sharing, business-IT cooperation, and a learning-oriented mindset. These cultural factors contribute significantly to BI effectiveness and the ability to navigate dynamic business landscapes. The paper proposes pillars of agile maturity supported by an open organizational culture, including efficient communication, information integration, creative problem-solving, and close collaboration between business and IT. These pillars underscore the importance of a flexible and open mindset in navigating BI challenges and ensuring sustained value. Empirical validation and further research are suggested to deepen our understanding of the impact of organizational culture on BI agility and effectiveness.

The alternating stress caused by periodic high-pressure injection and extraction in gas storage can potentially induce fault slippage, compromising the sealing integrity of faults within these facil-ities. Understanding the mechanical behavior of faults under alternating stress is crucial for en-suring the long-term stability and safety of gas storage operations. To explore the impact of fault dip angle and fault gouge strength on fault slip characteristics, fault samples were prepared with uniaxial compressive strengths of 20.1, 30.2, 42.4, and 51.4 MPa at two distinct dip angles. Triaxial compression experiments were conducted under alternating stress conditions corresponding to operational pressures at a specific gas storage in China. Results indicate that faults with dip angles of 30° and 45° tend to fail at their weakest points. Increasing strength of fault gouge shifts failure mechanisms from interfacial failure between gouge and surrounding rock towards internal gouge failure, often accompanied by shear failure across sections, resulting in characteristic "X"-shaped conjugate shear failures. The decrease in the ratio of bedrock strength to fault gouge strength elucidates the observed phenomena of initial reduction followed by increased fault deformation. Transition points for faults with 30° and 45° dips occur around the strength ratios of 1.7/1 and 1.2/1, respectively. Fault damage exhibits a negative correlation with fault gouge strength and a positive correlation with fault dip angle. Samples with higher strength fault gouge at a 30° dip angle generally incur less damage compared to those with lower strength fault gouge at a 45° dip angle. Moreover, higher maximum static friction coefficients denote greater fault resistance to slipping, with 30° faults consistently demonstrating superior resistance compared to 45° faults. Additionally, higher strength fault gouge consistently enhances slip resistance under identical dip angles.

The work proposes a backtesting analysis in comparison between the Lee-Carter and the Cairns-Blake-Dowd mortality models, employing Italian data. The mortality data come from the Italian National Statistics Institute (ISTAT) database and span the period 1975-2014, over which we computed back-projections evaluating the performances of the models in comparisons with real data. We propose three different backtest approaches, evaluating the goodness of short-run forecast versus medium-length ones. We find that both models were not able to capture the improving shock on the mortality observed for the male population on the analyzed period. Moreover, the results suggest that CBD forecast are reliable prevalently for ages above 75, and that LC forecast are basically more accurate for this data.

We propose a method for creating parallel Bessel-like vortical optical needles with an arbitrary axial intensity distribution via superposition of different cone-angle Bessel vortices. We analyze the interplay between the separation of individual optical vortical needles and their respective lengths and introduce a super-Gaussian function as their axial profile. We also analyze the physical limitations to observe well-separated optic needles, as they are influenced by mutual interference of the individual beams. To verify our theoretical and numerical results, we generate controllable spatial arrays of individual Bessel beams with various numbers and spatial separations by altering the spectrum of the incoming laser beam via the spatial light modulator. We demonstrate experimentally how to implement such beams using a diffractive mask. The presented method facilitates the creation of diverse spatial intensity distributions in three dimensions, potentially finding applications in specific microfabrication tasks or other contexts. These beams may have benefits in laser material processing applications such as nanochannel machining, glass via production, modification of glass refractive indices, and glass dicing.

The current work reveals the fine tuning between stability zones and randomness of Pointwise Stationary Fluid Flow Approximation (PSFFA) model of the non-stationary queueing D/M/1 system. More specifically, this clearly provides more insights into developing a contemporary PSFFA theory that unifies non-stationary queueing theory with chaos theory and fields in both theoretical physics and chaotic systems. This opens new grounds for stability analysis of non-stationary queueing systems.

The Chikungunya virus (CHIKV) poses a significant global public health concern, especially in Africa. Since its first isolation in Tanzania in 1953, CHIKV has caused recurrent outbreaks, challenging healthcare systems in low-resource settings. Recent outbreaks in Africa highlight the dynamic nature of CHIKV transmission and the challenges of underreporting and underdiagnosis. Here, we review literature and analyze publicly available cases, outbreaks, and genomic data providing insights into the epidemiology, genetic diversity, and transmission dynamics of CHIKV in Africa. Our analyses reveal the circulation of geographically distinct CHIKV genotypes, with certain regions experiencing a disproportionate burden of disease. Phylogenetic analysis of sporadic outbreaks in West Africa suggests repeated emergence of the virus through enzootic spillover, which is markedly different from inferred transmission dynamics in East Africa, where the virus is often introduced from Asian outbreaks, including the recent reintroduction of the Indian Ocean lineage from the Indian subcontinent to east Africa. Furthermore, there is limited evidence of viral movement between these two regions. Understanding the history and transmission dynamics of outbreaks is crucial for public health planning. Despite advances in surveillance and research, diagnostic and surveillance challenges persist. This review and secondary analysis highlight the importance of ongoing surveillance, research, and collaboration to mitigate the burden of CHIKV in Africa and improve public health outcomes.

This paper deals with a non-standard finite difference scheme defined on a quasi-uniform mesh for approximate solutions of the Magneto-Hydro Dynamics (MHD) boundary layer flow of an incompressible fluid past a flat plate for a wide range of the magnetic parameter. We show how to improve the obtained numerical results via a mesh refinement and a Richardson extrapolation. The obtained numerical results are favourably compared with those available in the literature.

Topological interlocking assembly (TIA) and computational architecture treat form as an emergent property of a material system, where the final shape results from the interplay of geometries and geometric interdependencies influenced by material, structural, and fabrication constraints. This paper posits that TIA is an ideal pedagogical tool for introducing students to computational architecture, its theoretical foundations and design principles. Specifically, defining TIA as a material system provides a robust educational approach for engaging students with computation, fostering design processes through bottom-up, hands-on investigations and procedural logic, understanding generative geometric rules, and exploring the flexibility of parametric variations. The methodology is illustrated through a Design Workshop and study unit from the Bachelor’s and Master’s programs at the Faculty for the Built Environment, University of Malta. The paper presents four investigations of defining a material system based on TIA - of tetrahedra, cones, octahedra, and osteomorphic blocks—as case studies to demonstrate how these exercises introduce students to computational thinking, parametric design, and fabrication techniques. Finally, the paper discusses the advantages and limitations of this pedagogical methodology.

Physical measurements might display range values extending towards infinite. The occurrence of infinity in physical equations, such as the black hole singularities, is a troublesome issue that causes many theories to break down when assessing extreme events. Different methods, such as re-normalization, have been proposed to avoid detrimental infinity. Here a novel technique is proposed, based on physical geometrical considerations and the Alexander Horned sphere, that permits to undermine infinity in physical equations. In this unconventional approach, a continuous monodimensional line becomes an assembly of countless bidimensional lines that superimpose in quantifiable knots and bifurcations.

3D city models are being extensively used in applications such as evacuation scenarios and energy consumption estimation. The main standard for 3D city models is the CityGML data model which can be encoded through the CityJSON data format. CityGML and CityJSON use polygonal modelling in order to represent geometries. True topological data structures have proven to be more computationally efficient for geometric analysis compared to polygonal modelling. In a previous study, we have introduced a method to topologically reconstruct CityGML models while maintaining the semantic information of the dataset, based solely on the combinatorial map (C-Map) data structure. As a result of the limitations of C-Map's semantic representation mechanism, the resulting datasets could suffer either from semantic information loss or the redundant repetition of them. In this article, we propose a solution for a more efficient representation of both geometry, topology and semantics by incorporating the C-Map data structure in the CityGML data model and implementing a CityJSON extension to encode the C-Map data. In addition, we provide an algorithm for the topological reconstruction of CityJSON datasets to append them according to this extension. Finally, we apply our methodology to three open datasets in order to validate our approach when applied to real-world data. Our results show that the proposed CityJSON extension can represent all geometric information of a city model in a lossless way, providing additional topological information for the objects of the model.

Recently, microfluidics deformability cytometry has emerged as a powerful tool for high throughput mechanical phenotyping of large populations of cells. These methods characterize cells by their mechanical fingerprints through exerting hydrodynamic forces and monitoring the resulting deformation. These devices have shown great promise for label free cytometry, yet there is a critical need to improve their accuracy and reconcile any discrepancies with other methods, such as atomic force microscopy. In this study, we employ computational fluid dynamics simulations and uncover how the elasticity of frequently used carrier fluids such as methyl-cellulose dissolved in phosphate-buffered saline is significantly influential to the resulting cellular deformation. We conducted CFD simulations that are conventionally used within the deformability cytometry field, which neglect fluid elasticity. Subsequently, we incorporated a more comprehensive model that simulates the viscoelastic nature of the carrier fluid. A comparison of the predicted stresses between these two approaches underscores the significance of the emerging elastic stresses in addition to the well-recognized viscous stresses along the channel. Furthermore, we utilize a two-phase flow model to predict the deformation of a promyelocyte (i.e. HL-60 cell type) within a hydrodynamic constriction channel. The obtained results highlight a substantial impact of the elasticity of carrier fluid on cellular deformation and raise questions about the accuracy of mechanical property estimates derived by neglecting elastic stresses.

Metabolites present in the hemolymph of honey bees play a crucial role in modulating the metamorphic process within the species. However, the precise alterations in metabolite composition, along with the associated variances and regulatory pathways implicated during the larvae-to-pupae metamorphosis of honey bees, remain incompletely elucidated. In this investigation, we gathered hemolymph samples from honey bee larvae at three distinct physiological stages-feeding, prepupal, and pupae and subjected them to metabolite analysis utilizing the liquid chromatography-mass spectrometry (LC-MS) technique. Employing principal component analysis (PCA) and partial least squares-discriminant analysis (PLS-DA), we identified significant differential metabolites and conducted a metabolic pathway analysis on those differentially up-regulated during the prepupal and pupae stages. Notably, metabolites up-regulated in the hemolymph of prepupal stage larvae primarily governed glucose metabolism and fat digestion and absorption, while those in pupae stage larvae were involved in regulating chitin and lipopolysaccharide precursor formation, as well as the biosynthesis of phenylalanine, tyrosine, and tryptophan. These findings bear significant implications for advancing our comprehension of the metamorphic processes in honey bees.

The present review paper aims at collecting and discussing the research work, numerical and experimental, carried out in the field of Fluid-Structure Interaction (FSI) in one-dimensional (1D) pressurized transient flow in the time-domain approach. Background theory and basic definitions are provided for the proper understanding of the assessed literature. A novel frame of reference is proposed for the classification of FSI models based on pipe degrees-of-freedom. Numerical research is organized according to this classification, while an extensive review on experimental research is presented by institution. Engineering applications of FSI models are described and historical accidents and post-accident analyses documented.

On 17 October 1947, Niels Bohr was made a knight of the Order of the Elephant by the King of Denmark in view of his outstanding achievements and contributions to science. Bohr designed his own coat of arms that featured a pattern of Yin and Yang (Tai Chi symbol) to symbolize the wave-particle complementarity. However, Bohr’s Yin-Yang diagram (YYD) was neither drawn based on the principles of quantum mechanics, nor did it originate from the traditional Taoist YYD. Scientists still have doubts about the legitimacy of using YYD as the icon of the wave-particle complementarity, because the YYD belonging to quantum mechanics itself is unknown so far. This article reports the YYDs existing in quantum mechanics and justifies the role of YYD in the wave-particle duality by showing that any system, whether classical or quantum, has an ideal YYD as long as it satisfies Bohr’s principle of complementarity (BPC). The deviation of a deformed YYD from the ideal YYD indicates the extent to which a real system satisfies BPC. This article constructs the quantum YYD by the complex quantum trajectory of a particle tunneling via a step barrier, which displays the continuous transition between the wave behavior and the particle behavior. It appears that the YYD designed by Bohr in his coat of arms resembles the YYD generated by tunneling motion, not only in appearance but also in the governing equation.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

This work presents a novel approach for the study of the movement of droplets on inclined surfaces under the influence of gravity and chemical heterogeneities. The developed numerical methodology uses data-driven modeling to extend the applicability limits of an analytically derived reduced-order model for the contact line velocity. More specifically, while the reduced-order model is able to capture the effects of the chemical heterogeneities to a satisfactory degree, it does not account for gravity. To alleviate this shortcoming, datasets generated from direct numerical simulations are used to train a data-driven model for the contact line velocity, which is based on the Fourier neural operator and corrects the reduced-order model predictions to match the reference solutions. This hybrid surrogate model, which comprises of both analytical and data-driven components, is then integrated in time to simulate the droplet movement, offering a speedup of five orders of magnitude compared to direct numerical simulations. The performance of this hybrid model is quantified and assessed in different wetting scenarios, by considering various inclination angles and values for the Bond number, demonstrating the accuracy of the predictions as long as the adopted parameters lie within the ranges considered in the training dataset.

A topological quantum interplay between the magnetic flux and the mass has been investigated, for the case of an electron, by evaluating a gauge-invariant phase factor (a Wilson loop) linked to the electromagnetic gauge field of the particle. In particular, from this phase factor and the quantization of the magnetic flux variations, a relationship between the mass at rest of the electron and its self-energy , arising from radiative corrections, has been obtained also within a QED approach. Besides, a formulation of an energy scale comparable to the energy at rest of an electron-positron pair is proposed. Remarkably, a reckoning of the Bohr energy of a W⁺ W^- pair is compatible with constants and parameters usually employed within the electroweak theory and comparable to the energy at rest of an electron-positron pair.

In this work the general problem of the characterization of the topological phase of an open quantum system is addressed. In particular, we study the topological properties of Kitaev chains and ladders under the perturbing effect of a current flux injected into the system using an external normal lead and derived from it via a superconducting electrode. After discussing the topological phase diagram of the isolated systems, using a scattering technique within the Bogoliubov-de Gennes formulation, we analyze the differential conductance properties of these topological devices as a function of all relevant model parameters. The relevant problem of implementing local spectroscopic measurements to characterize topological systems is also addressed by studying the system electrical response as a function of the position and the distance of the normal electrode (tip). The results show how the signatures of topological order affect the electrical response of the analyzed systems, a subset of such signatures being robust also against the effects of a moderate amount of disorder. The analysis of the internal modes of the nanodevices demonstrates that topological protection can be lost when quantum states of an initially isolated topological system are hybridized with those of the external reservoirs. The conclusions of this work could be useful in understanding the topological phases of nanowire-based mesoscopic devices.

The topological index is a numerical quantity based on the characteristics of various invariants or molecular graph. For ease of discussion, these indices are classified according to their logical derivation from topological invariants rather than their temporal development. Degree based topological indices depends upon the degree of vertices. This paper computes degree based topological indices of Bismuth Tri-Iodide chains and sheets with the help of M-polynomial.

In the study of QSAR/QSPR, due to high degree of predictability of pharmaceutical properties, the eccentric-connectivity index has very important place among the other topological descriptors, In this paper, we compute the exact formulas of eccentric-connectivity index and its corresponding polynomial, total eccentric-connectivity index and its corresponding polynomial, first Zagreb eccentricity index, augmented eccentric-connectivity index, modified eccentric-connectivity index and its corresponding polynomial for a class of phosphorus containing dendrimers.

Background: Vestibular Neuritis (VN) induces Acute Vestibular Syndrome (AVS). This study aimed to identify predictive factors of VN recovery by healing and/or compensation. Methods: In this longitudinal and prospective study, 40 patients were included. The first assessment (T0) included medical history taking (general and specific), for cardiovascular risk factors (CVRFs), a battery of diagnostic tests, bithermal caloric test (BCT), video Head Impulse Test (VHIT) and skull vibration induced nystagmus (SVIN). All patients also completed a Dizziness Handicap Inventory (DHI). All assessments were repeated 90±15 days (T3) later. Subjective criteria compensation were based on DHI total score and objective criteria compensation on the instrumental test results. Four groups of patients (A, B, C, D) were delineated by combining patients with normal vs abnormal vestibular tests and patients with normal vs abnormal DH. Results: CVRFs were associated with a poorer recovery of symptoms but not the age or BMI. Vestibular tests mainly BCT (canal paresis %), VHIT (lateral semicircular canal gain) and SVINT (nystagmus slow phase velocity) recovered within normal values in 20%, 20%, 26% of cases respectively at T3 for the 40-patient group. Conclusions: Vascular risk factors (hypercholesterolemia) are correlated with patients who do not recover their symptoms either by healing or compensation. The evolution did not show any significant difference between high or low frequency vestibular tests in patients recovering from their symptoms. However, some patients with objective recovery may continue to show persisting subjective symptoms.

Topological data analysis (TDA) is a recent approach for analyzing and interpreting complex data sets, based on ideas a branch of mathematics called algebraic topology. TDA has proven useful to disentangle non-trivial data structure in a broad range of data analytics problems including the study of cardiovascular signals. This review aims to provide an overview of the application of TDA to cardiovascular signals and its potential to enhance the understanding of cardiovascular diseases and their treatment. We first introduce the concept of TDA and its key techniques, including persistent homology, Mapper, and multidimensional scaling. We then discuss the use of TDA in analyzing various cardiovascular signals, including electrocardiography, photoplethysmography, and arterial stiffness. We also discuss the potential of TDA to improve the diagnosis and prognosis of cardiovascular diseases, as well as its limitations and challenges. Finally, we outline future directions for the use of TDA in cardiovascular signal analysis and its potential impact on clinical practice. Overall, TDA has shown great promise as a powerful tool for the analysis of complex cardiovascular signals and may offer significant insights into the understanding and management of cardiovascular diseases.

The study of photonic crystals has emerged as an attractive area of research in nanoscience in the last years. In this work we study the properties of a two-dimensional photonic crystal composed of dielectric rods. The unit cell of the system is composed of six rods organized on the sites of a C6 triangular lattice. We induce a topological phase by introducing an angular perturbation ϕ in the pristine system. The topology of the system is then determined by using the so-called k.p perturbed model. Our results show that the system presents a topological and a trivial phases, depending on the sign of the angular perturbation ϕ. The topological character of the system is probed by evaluating the electromagnetic energy density and analyzing its distribution in the real space, in particular on the maximal Wyckoff points. We also find two edge modes at the interface between the trivial and topological photonic crystals, which present a pseudospin topological behavior. By applying the Bulk-Edge correspondence, we study the pseudospin edge modes and conclude that they are robust against defects, disorder and reflection. Moreover, the localization of the edge modes leads to the confinement of light and the interface behaves as a waveguide for the propagation of electromagnetic waves. Finally, we show that the two edge modes present energy flux propagating in opposite directions, which is the photonic analogue of the quantum spin Hall effect.

In 1999, Molodtsov initiated the theory of soft sets as a new mathematical tool for dealing with uncertainties in many fields of applied sciences. In 2011, Shabir and Naz introduced and studied the notion of soft topological spaces, also defining and investigating many new soft properties as generalization of the classical ones. In this paper, we introduce the notions of soft separation between soft points and soft closed sets in order to obtain a generalization of the well-known Embedding Lemma to the class of soft topological spaces.

In this study, the friction factor of turbulent pipe flow for dried rice malt extract solutions is reduced experimentally to that of a Newtonian fluid. The friction factor is measured for four types of solutions at different culture times and concentrations. The results indicate that the experimental data points of the test solutions diverge from the maximum drag reduction asymptote at and above Re√f ≅ 200 and align parallel to those of Newtonian fluids. This drag reduction phenomenon differs from that of artificial high molecular polymer solutions. It is classified as a Type B drag reduction phenomenon of biopolymer solutions and fine solid particle suspensions. The order of drag reduction corresponds approximately to that of 5–50 ppm xanthan-gum solutions reported previously. Furthermore, the velocity profile in a turbulent pipe flow was predicted using a semi-theoretical equation, in which the friction factors were determined using the difference between the experimental results of the tested solutions and Newtonian fluids. The results indicate a more considerable thickening of the viscous sublayer in the turbulent pipe flow of the test solutions than that of Newtonian fluids.

Kisspeptin, a key neuropeptide derived from the KISS1 gene, is renowned for its critical role in regulating the hypothalamic-pituitary-gonadal axis and reproductive hormone secretion. Beyond its primary function in reproductive biology, emerging research has illuminated its influence in various cancers, mediating significant effects through its interaction with the G-protein coupled receptor, Kisspeptin receptor. This interaction has been implicated in modulating cellular pro-cesses such as proliferation and metastasis, making it a potential target for therapeutic interven-tion. Our study initially screened ten kisspeptin-10 analogs through cytotoxic effects of kisspep-tin-10 (KP10) and its analogs in several cancer types, including cervical, prostate, breast, and gastric cancers, with a particular focus on cervical cancer where the most profound effects were observed. Further exploration using kinase array assays revealed that these analogs specifically alter key kinases involved in cancer progression. Migration assays demonstrated a substantial decrease in cell motility, and Bioluminiscence Resonance Energy Transfer assays confirmed these analogs strong interactions with the kisspeptin receptor. Overall, our results indicate that these KP10 analogs not only hinder cervical cancer cell proliferation but also curtail migration through targeted modulation of kinase signaling, suggesting their potential as therapeutic ayfgents in managing cervical cancer progression. This comprehensive approach underscores the therapeutic promise of exploiting kisspeptin signaling in cancer treatment strategies.