The power converter is the significant device in a wind power system. Wind turbine will be shut down and off grid immediately with the occurrence of the IGBT module open-circuit fault of power converter, which will seriously impact the stability of grid and even threaten personal safety. However, in the existing diagnosis strategies of power converter, there are few single and double IGBT modules open-circuit fault diagnosis methods producing negative results including erroneous judgment, omissive judgment and low accuracy. In this paper, a novel method to diagnose the single and double IGBT modules open-circuit faults of the permanent magnet synchronous generator (PMSG) wind turbine grid-side converter (GSC) is proposed. Above all, collecting the three-phase current varying with wind speed of 22 failure states including a normal state of PMSG wind turbine GSC as the original signal data. Afterward, the original signal data are decomposed by using variational mode decomposition (VMD) to obtain the mode coefficient series, which are analyzed by the proposed method base on fault trend feature for extracting the trend feature vectors. Finally, the trend feature vectors are used as the input of deep belief network (DBN) for decision-making and obtaining the classification results. The simulation and experimental results show that the proposed method can diagnose the single and double IGBT modules open-circuit faults of GSC, and the accuracy is higher than the benchmark models.

The ability to detect the presence as well as classify the activities of individuals behind visually obscuring structures is of significant benefit to police, security and emergency services in many situations. This paper presents the analysis from a series of experimental results generated using a through-the-wall (TTW) Frequency Modulated Continuous Wave (FMCW) C-Band radar system named Soprano. The objective of this analysis was to classify whether an individual was carrying an item in both hands or not using micro-Doppler information from a FMCW sensor. The radar was deployed at a standoff distance, of approximately 0.5 m, outside a residential building and used to detect multiple people walking within a room. Through the application of digital filtering, it was shown that significant suppression of the primary wall reflection is possible, significantly enhancing the target signal to clutter ratio. Singular Value Decomposition (SVD) signal processing techniques were then applied to the micro-Doppler signatures from different individuals. Features from the SVD information have been used to classify whether the person was carrying an item or walking free handed. Excellent performance of the classifier was achieved in this challenging scenario with accuracies up to 94%, suggesting that future through wall radar sensors may have the ability to reliably recognize many different types of activities in TTW scenarios using these techniques.

Global warming may increase the potential evapotranspiration (Etp), thereby affecting the amount of clean water resources available in a region. In this study, the systematic biases in temperature outputs of 24 global climate models (GCMs) under 3 emission scenarios are corrected by using 8 bias correction methods. The trend of Etp in Yangzi River Delta in the 21st century is projected by using 4 Etp calculation formulas. The uncertainty of the projections is estimated and decomposed by using multi-way analysis of variance. The influence of uncertainty on the projected change signal is quantified by using the signal-to-noise ratio. The results show that, relative to the reference period (1971~2000), the annual mean daily Etp in Yangzi River Delta will increase by 0.14~0.17mm/d during the period 2021~2050 and by 0.21~0.41mm/d during the period 2061~2090, respectively. During 2021~2050, the uncertainty of Etp increase projections is dominantly contributed by the main effects of GCM (63%) and Etp calculation formula (24%). During 2061~2090, it is mainly contributed by the main effect of GCM (36%), followed by the main effects of emission scenario (34%) and Etp calculation formula (18%). The increase projections of Etp are generally reliable and robust during the two projection periods.

Structural health monitoring has been studied by a number of researchers as well as various industries to keep up with the increasing demand for preventive maintenance routines. This work presents a novel method for reconstruct prompt, informed strain/stress responses at the hot spots of the structures based on strain measurements at remote locations. The structural responses measured from usage monitoring system at available locations are decomposed into modal responses using empirical mode decomposition. Transformation equations based on finite element modeling are derived to extrapolate the modal responses from the measured locations to critical locations where direct sensor measurements are not available. Then, two numerical examples (a two-span beam and a 19956-degree of freedom simplified airfoil) are used to demonstrate the overall reconstruction method. Finally, the present work investigates the effectiveness and accuracy of the method through a set of experiments conducted on an aluminium alloy cantilever beam commonly used in air vehicle and spacecraft. The experiments collect the vibration strain signals of the beam via optical fiber sensors. Reconstruction results are compared with theoretical solutions and a detailed error analysis is also provided.

To make wind power more competitive, it is necessary to reduce turbine downtime and reduce costs associated with wind turbine Operation and Maintenance (O&M). Incorporating machine learning in developing condition-based predictive maintenance methodologies for wind turbines can enhance their efficiency and reliability. This paper presents a monitoring method that utilizes Base Density for the Support Vector Machine (BDSVM) and the evolutionary Fourier spectra of vibrations. This method allows smart monitoring of the function evolution of the turbine. A complex optimal function (FO) for 5-degree order has been developed that will be the boundary function of the BDSVM to timely determine the magnitude, frequency, and place of the failure occurring in wind turbine drive.

Long term Precipitation and temperature variations are one of the main determinants of climate variability of one’s area. The aim of this study is to determine trends variation in climatic elements of temperature and precipitation in the southern zone of Tigray regional state, Ethiopia. The station is assumed for the study of climatic records over southern zone of the region in detection for probable trends. The daily, monthly and annual precipitation totals and temperature observed at korem meteorological station were used for the period of 1981-2010 for Precipitation and 1985 – 2010 for minimum and maximum temperature. Summary of descriptive statistics and Mann Kendall test methods were employed for the observed data analysis to demonstrate any existence of possible trends. The main findings of the study indicated that the mean and maximum temperature had a general increasing trend; however, minimum temperature showed decreasing trend. In general annual temperature from 1985 – 2010 of the area showed a warming trend. Moreover analysis of the 30 years (1981-2010) annual precipitation showed a coefficient of variation ranging from 33.77 – 233 %. It indicated that the precipitation dissemination is not normal with large year to year variances.

We investigate and discuss in detail the structure of the restricted singular value decomposition for a tensor triplet under t-product (T-RSVD). The algorithm is provided with a numerical example illustrating the main result. For applications, we consider color image watermarking processing with T-RSVD.

Analysis of non-stationary and nonlinear sound signals obtained from dynamical processes is one of the greatest challenges in signal processing. Turning machine operation is a highly dynamic process persuaded by many events such as dynamical responses, chip formations and operational conditions of machining. Traditional and widely used fast Fourier transformation and spectrogram is not suitable for processing sound signals acquired from dynamical systems as its result have significant deficiencies because of stationary assumptions and having priori basis. The relatively new technique, Discrete Wavelet Transform, which uses Wavelet decomposition and the recently developed technique, Hilbert Huang Transform (HHT) which uses Empirical Mode Decomposition have notably better properties in the analysis of nonlinear and non-stationary sound signals. This paper presents a comparative study on the decomposition of multicomponent sound signals using Empirical Mode Decomposition and Wavelet Decomposition to highlight the suitability found in HHT to analyze tool-emitted sound signals received from turning processes. Apart from the short mathematical and theoretical foundations of the transformations, this paper demonstrates their decomposition strength using an experimental case study of tool flank wear monitoring in turning. It also concludes HHT is more suitable than DWT to analyze tool-emitted sound signals received from turning processes.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

The sudden and abrupt rise of COVID-19 became a challenge for the world economy. In this paper, we investigate the changes of a trend of mutual trade between the EU-15 countries and China during the demanding times of the COVID-19 crisis. We use monthly data for Chinese export to the EU (2018:01 – 2020:05) and import from the EU (2018:01 – 2020:07) relying on the data from open source Trademap. We employ descriptive statistics to analyze the trade. Overall, there is the obvious decline of 13-32 per cent in worldwide trade as predicted by the WTO. This affected China as the main trading partner of electronic devices and medical supplies. The trade between the EU and China has decreased, but the major change in demand brought the alteration in commodities structure and re-orientation of Chinese export production. In the first five months of 2020, we have witnessed strong engagement of the Chinese economy in new highly demanded production - mainly to articles strongly linked with healthcare and medical equipment. Thus, we have observed that the Chinese were very flexible in changing the structure of export which was triggered by COVID-19 crisis. This flexibility is worth further exploration.

In Bangladesh, climate change is a major concern because of its geophysical location and climate dependent agriculture. As sessile organisms, crops plants have to face difficulties often in this environmentally vulnerable country. Therefore, this study examines the seasonal trend of two climatic parameters viz. temperature (maximum and minimum) and rainfall over a period of 1983 to 2013. Besides, this study provides insight into the relationship between climatic parameters and crop yield of two major crops viz. rice and wheat during 1997-2013. To assess the relationship of climatic parameters with time and yield using Pearson correlation analysis, time series data used at an aggregate level. SPSS software utilized for this analysis. The cropping seasons such as rice growing seasons Aus (summer rice), Aman (autumn rice) and Boro (winter rice) exhibited a significant increase in maximum and minimum temperature. Rainfall found to have a decreasing trend for all the seasons. This study also revealed that the climatic parameters had significant effects on rice yield, but these results varied among three rice crops. Maximum temperature had positive effects on all rice yields, especially on Aus and Aman. Minimum temperature had a negative effect on Aman rice yield but a positive effect on Aus rice yield. Wheat yield negatively associated with temperature. Rainfall exhibited negative relation with both rice and wheat yield.

A new generalized definition of Mersenne numbers is proposed of the form (a^n - (a-1)^n), called Global Generalized Mersenne numbers, or simply Generalized Mersenne numbers and noted GM_{a,n} where a is the base and n is the exponent, both being positive integers. The properties are investigated for prime exponents n and several theorems on Mersenne numbers regarding their congruence properties are generalized and demonstrated. In particular, it is found that, for any base a, Generalized Mersenne numbers are in general such that (GM_{a,n} - 1) are even and divisible by n, a and (a-1) for any odd prime exponent n and by (a(a-1)+1) for any prime exponent n > 5. The remaining factor is a function of triangular numbers of (a-1), specific to each prime exponent n. Four theorems on Mersenne numbers are generalized and four new theorems are demonstrated, allowing to show first, that (GM_{a,n} - 1) are divisible by 6, and more precisely GM_{a,n} are congruent to 1(mod 12) or 7(mod 12) depending on the congruence of the base a(mod 4); second, that (GM_{a,n} - 1) are divisible by 10 if n == 1(mod 4) and, if n == 3(mod 4), GM_{a,n} == 1(mod 10), or 7(mod 10) or 9(mod 10) depending on the congruence of the base a(mod 5); third, that all factors c_{i} of GM_{a,n} are of the form (2nf_{i}+1) with f_{i} natural integers such that c_{i} is prime itself or the product of primes of the form (2nj+1) with j natural integer; fourth, that for odd prime exponents n, all GM_{a,n} are periodically congruent to either +/-1\(mod 8) or +/-3(mod 8) depending on the congruence of the base a(mod 8); and fifth, that the factors of a composite GM_{a,n} is of the form (2nf_{i}+1) with f_{i} == u(mod 4) and u being either 0, 1, 2 or 3 depending on the congruence of the exponent n(mod 4) and on the congruence of the base a(mod 8). The potential use of Generalized Mersenne primes in cryptography is shortly addressed.

Polyurethane is used extensively in the furniture industry, primarily in beds and sofas. There is a significant volume of research pertaining to the flammability of polyurethane materials, but very little regarding smoke toxicity. Given toxic fire effluents are a primary cause of injury and fatalities, more work needs to be done to test the toxicity of polyurethane materials and the fire retardants they are coated/bound with. The aim of the review is to provide a comprehensive analysis of the decomposition of polyurethane and discuss the development and application of modern fire retardants and their effect on smoke toxicity. This work then provides discussion on the challenges faced when attempting to quantify the toxicity of the effluent produced during combustion. Future work should aim to reduce the toxicity and flammability of polyurethane simultaneously by; reducing the pyrolysis of the polymer, preventing the escape of volatile products, reducing radicals within the system and lowering the temperature of the system. Before this can be achieved, a better understanding of smoke toxicity and the ability to test materials is needed.

Defect detection and identification from fruits and vegetables are particularly challenging for Indian agriculture. Defect Detection is a process to identify the defects or damages in vegetables and fruits, based on the shapes, colors and textures. The local market finds it difficult to cope with the defects and other infections in fruits and vegetables as quality evaluations and classification of vegetables and fruits have become tedious process. Recently, several approaches based on Image processing, Machine Learning and Artificial Intelligence methods have been proposed for the purpose of defect detection. On the basis of classifying the types of defects, related pathogens, and physical and morphological characteristics descriptors, we review the different approaches based on a corpus of 57 articles between 2016 and 2021. In the process of describing the defect analysis, steps from the target articles, algorithms, and methods including qualitative and quantitative evaluation are mainly summarized. The aim of this current review work is to present-day novel images and collects recent defective area calculation methods to detect surface defects of fruits and vegetables using RGB images and to classify whether the fruit is defected or fresh. A rigorous evaluation of many new algorithms provided for quality assurance by researcher’s probes of vegetables and fruits have been conducted in this work. This review work conveys that using the recent identification features will help to decrease the disadvantages in fruit storeroom owing to storage of the affected vegetables and fruits, ie. Preventing the spread of defects and other infections from the infected fruits and vegetables to the fresh ones.

Available water resources in the Middle East, as one of the most water-scarce regions of the world, have undergone extra pressure due to climatic change, population growth, and economic development during the past decades. The objective of this study is to detect the trends and quantify the changes in aridity with respect to precipitation and potential evapotranspiration in 20 countries of the Middle East and the adjacent area. A Pixel-wised trend analysis was conducted on precipitation, potential evapotranspiration, and aridity index for 71 years from 1948 to 2018. A nonparametric Mann-Kendall test was used over 14106 points in the study area to detect the trends at monthly and annual time scales. Results showed statistically significant (|Z| >1.96) upward trends in aridity (a downward trend in aridity index) up to 96 percent from December through September in most parts of the region. Aridity in October and November had a downward tendency in most parts of the study area. At the annual time scale, 62.5 percent of the statistically significant trends in aridity were found to be upward (up to 96 percent increase in aridity) due to the combined effects of the decrease in precipitation and the increase in potential evapotranspiration and 37.5 percent of the detected trends were downward (up to 61 percent decrease in aridity). The highest and the lowest trends in aridity were found in the north of Sudan (96 percent increase in aridity) and Eastern Arabia (61 percent decrease in aridity), respectively.

The study focused on two climatic variables i.e. precipitation and stream flow for analysing change in trend of rainfall for the River Ssezibwa Catchment area and stream flow of River Ssezibwa. This Catchment is found in the districts of Mukono and Buikwe in Uganda. In this area agriculture is majorly dependent on rainfall and irrigation on a small scale. However, rainfall occurrence has become unpredictable over the past few years as result of the changes in patterns of weather. This has caused severe effects on the agricultural cropping system as well as caused negative effects on the natural water resources. Stream flow data of 57 years (1960 – 2017) and rainfall data for 35 years (1982 – 2017) on a daily basis was analysed to find out the trend and detect change point. Trend analysis was done by using the non-parametric analysis while the change point detection was carried out by using the Pettit test (1979).Magnitude of trend for the time series data was carried out using Sen’s Slope estimator and Mann – Kendall test was done to determine the trend. Results from the statistical analysis highlighted that; for stream flow the trend was generally positive and change point detected to be in the year 2000 while for rainfall data analysis indicated that the trend was predominantly negative and change point was in the year 1998.

Objective: To visualize and analyze the published literature on diabetes and pyroptosis based on a bibliometric approach, so as to provide a comprehensive picture of the hot research directions and dynamic progress in this field. Methods: This study was based on the web of science core collection database to conduct a comprehensive search of the published literature in the field of diabetes and Pyroptosis from January 1985 to August 2022, including the published research literature in this field, as well as a visual analysis of the number of citations, year of publication, journal, author, research institution, country, and research topic. Results: A total of 139 literature on research related to diabetes and cellular scorch from 2011 to 2022 were retrieved, with a total of 3009 citations and a maximum of 255 citations for a single article, which had a first authorSchmid-Burgk, JL The first author of this article is from Germany; among 20 publishing countries, China leads with 100 articles; among 222 publishing institutions, Harbin Medical University leads with 18 articles and 184 citations; among 980 authors, Chen, X from China tops the list of high-impact authors with 5 articles and 29 citations; Among the 98 journals, "CELL DEATH DISEASE" ranked first in both volume and high impact journals with 4 articles and 29 citations; among 349 keywords, "pyroptosis" ranked first with a cumulative frequency of 65 times. The cluster analysis was divided into three categories, chronic complications of diabetes and pyroptosis (67 articles), diabetes and pyroptosis (60 articles), and diabetes combined with other diseases and pyroptosis (12 articles), and the number of articles related to diabetes and its chronic complications increased rapidly from 2019, among which, diabetic cardiomyopathy (27 articles) had the highest number of articles. Conclusions: Based on a comprehensive analysis of published literature in the field of diabetes and pyroptosis from 2011-2022, this study achieved a visual analysis of studies with significant and outstanding contributions to the field, thus framing a picture showing the development and changes in the field. At the same time, this study provides research information and direction for clinicians and investigators to conduct diabetes and pyroptosis related research in the future.

A set of programs for the numerical simulation of the diffusion decomposition processes was developed by using simulation methods, kinetic and particle method. The complex has been validated on the model system Ni-Al by the growth of -phase separations. The results on the evolution of the distribution function and other characteristics of the ensemble, which in the zero volume fraction approximation are asymptotically in good agreement with the theory and the experiment, have been obtained. The peculiarity of the created program complex is the possibility of its adaptation to the description of the decomposition of multicomponent multiphase systems. Fig. 6, list of references - 19 titles.

The thermal decomposition of brominated butyl rubber under air atmosphere was investigated by thermogravimetry (TG) and derivative thermogravimetry (DTG) at various heating rates. The kinetic parameters were evaluated by TG and the isoconversional method developed by Ozawa. One prominent decomposition stage was observed in the DTG curves at high heating rates while an additional small peak was observed at low heating rates. The apparent activation energy determined using the TG method ranged from 219.31–228.13 kJ·mol-1 at various heating rates. The non-isothermal degradation was found to be a first order reaction, and the activation energy, as determined by the isoconversional method, increased with an increase in mass loss. The kinetic data suggested that brominated butyl rubber had excellent thermal stability. This study will indirectly aid in improving rubber pyrolysis methods and in enhancing the heat resistance of materials.

Two desirable functions of healthy soil are nutrient cycling and pest suppression. We review recent literature on the contributions of soil microarthropods to soil health through their intersecting roles in decomposition and nutrient cycling and direct and indirect suppression of plant pests. Microarthropods can impact soil and plant health directly by feeding on pest organisms or serving as alternate prey for larger predatory arthropods, and indirectly, by mediating the ability of crop plants to resist or tolerate insect pests and diseases through interactions with the decomposition food web in support of plant nutrition. Soil fauna, including microarthropods, are key regulators of decomposition at local scales but their role at larger scales is unresolved. Future research priorities include the incorporation of multi-channel omnivory into food web modeling and understanding the vulnerability of our soil carbon to increased global temperatures.

We explored the dynamics of the two interacting information systems. We show that for the Markovian marginal systems the driving force for information dynamics is determined by both the information landscape and information flux. While the information landscape can be used to construct the driving force to describe the equilibrium time reversible information system dynamics, the information flux can be used to describe the nonequilibrium time-irreversible behaviours of the information system dynamics. The information flux explicitly breaks the detailed balance and is a direct measure of the degree of the nonequilibriumness or time irreversibility. We further demonstrate that the mutual information rate between the two subsystems can be decomposed into the equilibrium time-reversible and nonequilibrium time-irreversible parts respectively. This decomposition of the mutual information rate (MIR) corresponds to the information landscape-flux decomposition explicitly when the two subsystems behave as Markov chains. Finally, we uncover the intimate relationship between the nonequilibrium thermodynamics in terms of the entropy production rates and the time-irreversible part of the mutual information rate. We found that this relationship and MIR decomposition still hold for the more general stationary and ergodic cases. We demonstrate the above features with two examples of the bivariate Markov chains.

Abstract:High-pressure water jet technology has received extensive attention and application due to its high efficiency and environmental protection characteristics. The high-pressure water jet nozzle is its core component, and the research on the high-pressure water jet nozzle is conducive to improving the jet performance and improving the jet efficiency. This paper introduces the characteristics of water jet and the working principle of pure water jet, abrasive water jet, pulsed water jet and cavitation water jet, reviews the theoretical analysis and experiment of the predecessor's nozzle, briefly explains the application of high-pressure water jet and looks forward to the development trend of this technology.

With the development of information technology and the wide application of building information modelling technology, the construction industry continues to make digital changes. Managers are trying to apply smart construction site management to promote the upgrading of production modes. We used CiteSpace software to analyze 1707 articles from China National Knowledge Infrastructure, Web of Science and Scopus to understand the current research hotspots of global scholars in this field. Results show that: (1) The number of studies on smart construction sites increases rapidly by year. Researchers from China, America and the UK have the most influential studies. (2) The cooperation between researchers and institutions is not close enough. In addition, the directions of research in the field are still scattered; (3) Chinese scholars are good at building intelligent platforms and evaluating intelligent systems from multiple perspectives. International scholars are willing to pursue technological innovation, allowing the continuous development of intelligent construction technology. (4) The applications in this field have not been popularized despite relatively perfect technology and typical cases. Future scholars should gradually improve the theoretical basis and industry standards of smart construction sites, promote the development of intelligent construction technology and establish the evaluation standards of qualified smart sites. This study will provide scholars in this field with the theoretical basis and research directions for further in-depth research, help construction companies to understand the development status and trend of smart construction sites and accelerate the intelligent transformation of construction companies.

The partial information decomposition (PID) framework is concerned with decomposing the information that a set of random variables has with respect to a target variable into three types of components: redundant, synergistic, and unique. Classical information theory alone does not provide a unique way to decompose information in this manner and additional assumptions have to be made. Inspired by Kolchinsky's recent proposal for measures of intersection information, we introduce three new measures based on well-known partial orders between communication channels and study some of their properties.

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

This report provides a comprehensive overview of occupational asthma and respiratory hypersensitivity, focusing on some chemicals used in the workplace Includes numerous case studies and research papers related to occupational exposure methacrylates, such as HEMA-HPMA, and respiratory hypersensitivity are discussed And the relationship is explored The book also examines asthma pathophysiology, emerging drug delivery systems used to treat asthma, and the potential of nanoparticles , dendrimers and micellar systems have to improve pulmonary drug delivery in detail The worldwide prevalence of asthma is highlighted, with higher rates in high-GDP countries. The book highlights the need to improve asthma diagnosis, treatment and biomarkers, particularly in rural and low-income countries where the disease is often underdiagnosed and inadequately treated, and discusses the role of inflammation in asthma, in particular secondary inflammation characterized by specific cytokines and inflammation cells In addition, the paper explores various drug delivery methods, such as parenteral and parenteral drugs, pressurized inhalers (pMDIs), dry powder inhalers ( DPIs), nebulizers, nanoparticles, liposomes, micellar systems, microparticles , dendrimers, and gene therapy . These systems aim to increase pulmonary delivery of drugs and improve clinical outcomes. The potential of dendrimer bilirubin-based nanoparticles and micellar systems in the treatment of asthma and lung inflammatory diseases, including asthma, has been discussed in summary, this paper provides an overview of occupational asthma and respiratory hypersensitivity, and this discussion highlights the association between methacrylate exposure and respiratory hypersensitivity.

Systematic traders employ algorithmic strategies to manage their investments. As a result of the deterministic nature of such strategies, it is possible to determine their exact responses to any conceivable set of market conditions. Consequently, sensitivity analysis can be conducted to systematically uncover undesirable strategy behavior and enhance strategy robustness by adding controls to reduce exposure during periods of poor performance / unfavorable market conditions or increase exposure during periods of strong performance / favorable market conditions. In this study, we formulate both a simple systematic trend-following strategy (i.e., trading model) to simulate investment decisions, and a market model to simulate the evolution of instrument prices. We then map the relationship between market model parameters under various conditions and strategy performance. We focus, in particular, on identifying the performance impact of changes in both serial dependence in price variability and changes in the trend. The long-range serial dependence of the true range worsens performance of the simple classic trend-following strategy. During periods of strong performance, the dispersion of trading outcomes increases significantly as long-range serial dependence increases.

This research delves into a detailed exploration of the thermal decomposition behavior of bio-based polymers, specifically Thermoplastic Starch (TPS) and Poly(lactic acid) (PLA). The study focuses on the impact of three different heating rates under a nitrogen atmosphere, providing comprehensive insights into the thermal stability of these eco-friendly polymers. In particular, the TPS kinetic model is examined, encompassing the decomposition of three distinct fractions. In contrast, PLA exhibits a simplified kinetic behavior requiring only a fraction described by a zero-order model. The kinetic study involves a systematic investigation into the individual contributions of key components within TPS, including starch, glycerin, and polyvinyl alcohol (PVA). This nuanced analysis contributes to a comprehensive understanding of the thermal degradation process of TPS and PLA, enabling the optimization of processing conditions and the prediction of material behavior across varying thermal environments. Furthermore, the incorporation of different starch sources and calcium carbonate additives in TPS enhances our understanding of the polymer's thermal stability, offering insights into potential applications in diverse industries.

Spatio-Temporal Dynamic Mode Decomposition (STDMD) is an extension of Dynamic Mode Decomposition (DMD) designed to handle spatio-temporal datasets. It extends the framework so that it can analyze data that has both spatial and temporal variations, allowing for the extraction of spatial structures and their temporal evolution. The STDMD method extracts temporal and spatial development information simultaneously, including wavenumber, frequencies and growth rates, which is essential in complex dynamic systems. We provide a comprehensive mathematical framework for sequential and parallel STDMD approaches. We also introduce delay coordinates generalization to the presented algorithms to extend the scope of their application. The extension, labeled delay embedding STDMD allows the use of delayed data, which can be both time-delayed and space-delayed. An explicit expression of the presented algorithms in matrix form is also provided, which facilitates theoretical analysis and provides a solid foundation for further research and development. The novel approach is demonstrated using some illustrative model dynamics.

As a fast and nondestructive spectroscopic analysis technique, Raman spectroscopy has been widely applied in chemistry. However, noise is usually unavoidable in Raman spectra. Hence, denoising is an important step before Raman spectral analysis. A novel spectral denoising method based on variational mode decomposition (VMD) was introduced to solve the above problem. The spectrum is decomposed into a series of modes (uk) by VMD. Then, the high frequency noise modes are removed and the remaining modes are reconstructed to obtain the denoised spectrum. The proposed method was verified by two artificial noised signals and two actual Raman spectra. As comparison, empirical mode decomposition (EMD), Savitzky-Golay (SG) smoothing and discrete wavelet transformation (DWT) are also investigated. At the same time, signal-to-noise ratio (SNR) was introduced as evaluation indicators to verify the performance of the proposed method. The results show that compared with EMD, VMD can significantly improve mode mixing and endpoint effect. Some information of the small sharp peak is lost after VMD denoising. However, VMD lost fewer information than that of EMD, SG smoothing and DWT. Moreover, the Raman spectrum by VMD denoising is more excellent than that of EMD, SG smoothing and DWT in terms of visualization and SNR. Therefore, VMD provides superior denoising capabilities for Raman spectra.

The solution of structural problems with nonlinear material behaviour in a model order reduction framework is investigated in this paper. In such a framework, greedy algorithms or adaptive strategies are interesting as they adjust the reduced order basis (ROB) to the problem of interest. However, these greedy strategies may lead to an excessive increase in the size of the reduced basis, i.e. the solution is no more represented in its optimal low-dimensional expansion. Here, an optimised strategy is proposed to maintain, at each step of the greedy algorithm, the lowest dimension of the PGD basis using a randomised SVD algorithm. Comparing to conventional approaches such as Gram-Schmidt orthonormalisation or deterministic SVD, it is shown to be very efficient both in terms of numerical cost and optimality of the reduced basis. Examples with different mesh densities are investigated to demonstrate the numerical efficiency of the presented method.

We propose an electrocardiogram (ECG) signal-based algorithm to estimate the respiratory rate is a significant informative indicator of physiological state of a patient. The consecutive ECG signals reflect the information about the respiration because inhalation and exhalation make transthoracic impedance vary. The proposed algorithm extracts the respiration-related signal by finding out the commonality between the frequency and amplitude features in the ECG pulse train. The respiration rate can be calculated from the principle components after the procedure of the singular spectrum analysis. We achieved 1.7569 breaths per min of root-mean-squared error and 1.7517 of standard deviation with a 32-seconds signal window of the Capnobase dataset, which gives notable improvement compared with the conventional Autoregressive model based estimation methods.

Empirical models help us understand the process of plant residue decomposition and nutrient release into the soil. The objective of this study was to determine an appropriate model to describe the decomposition of hairy vetch (Vicia villosa Roth) and cereal rye (Secale cereale L.) cover crop (CC) residue and nitrogen (N) release. Data pertaining to above and belowground CC residue mass loss and N release for up to 2633 cumulative decomposition degree days (112 d) after litterbag installation were obtained from two cropping system experiments, one conducted in 2015 and the other in 2017 and 2018 at the humid subtropical environment of southern IL, USA. Six exponential and two hyperbolic models were fit to percent mass and N remaining data to find the one with minimum Akaike Information Criterion (AIC) and residual sum of squares. Modified three-parameter single exponential and two- or three-parameter hyperbolic models best met the assumed criteria of selection for above and belowground CC residue, respectively. Fitting a double exponential model to a combined data for percent mass and N remaining, which identified two mass and N pools, a fast and a slow pool with different rate constants. A five-parameter double exponential with an asymptote met the preset criteria and passed all tests for normally distributed population, constant variance, and independence of residuals at α = 0.05 when fit to combined data of hairy vetch shoot mass and N remaining. However, a two-parameter hyperbolic and three-parameter asymptotic hyperbolic model provided the best fit to a combined data of cereal rye shoot mass and N remaining, respectively. Both hyperbolic decay models showed a good fit for belowground mass decomposition and N release for both CCs. Cereal rye had poorer fit than hairy vetch for mass and N remaining of both above and belowground mass. The best-selected decay models can be used to estimate the decomposition and N release rates of hairy vetch and cereal rye above and belowground residue in a similar environment.

Magnesium alloy stents have been extensively studied in the field of biodegradable metal stents due to their exceptional biocompatibility, biodegradability and excellent biomechanical properties. Nevertheless, the specific in vivo service environment causes magnesium alloy stents to degrade rapidly and fail to provide sufficient support for certain time. This paper presents an overview of the development history and protection strategies for magnesium alloy stents. Alloying, optimizing stent structure and preparing protective coating have improved the corrosion resistance of magnesium alloy stents. Based on the corrosion mechanism of magnesium alloy stents, as well as their deformation during use and environmental characteristics, we present some novel solution strategies aiming at reducing the corrosion rate of magnesium alloys and enhancing the comprehensive performance of magnesium alloy stents. These strategies include adapting protective coatings for the deformation of the stents, preparing rapid endothelialization coatings to enhance the service environment of the stent, and constructing coatings with self-healing functions. It is hoped that this review can help to understand the development of magnesium alloy cardiovascular stents and solve the problems related to magnesium alloy stents in clinical applications at the early implantation stage.

The recent happenings in the world such as flood and wild forest fire were as a result of climate effect as being envisaged by scientists. It is urgent now to adopt a source of energy that will eliminate this effect on our universe. Solar energy is the major energy means that is abundant which could be utilized. In this review, the prospects of solar energy exploration were studied in Nigeria which include assessments, economic viability and hybrid systems. Findings show higher potential in the North as compared to the Southern region. Additionally, potential of offshore solar energy system was simulated by considering 2002, 2003 and 2004 data sets from Era5-land base. Their monthly mean, seasonal changes and annual mean value were estimated. The algebraic annual solar radiance for 2002, 2003 and 2004 were 34,914.732 kWh/m2, 33,898.316 kWh/m2 and 34,338.324 kWh/m2. Suggestions were made due to the present status of solar energy utilization that will enhance its maximum usage and development. One of these is the establishment of a functioning financial scheme and the database for all renewable energy systems. When all these are put in place, the energy supply will increase, climate effect will be reduced, and the economy will be boosted.

The paper investigates new robust code constructions based on bent functions and spline–wavelet transformation. Implementation of bent functions in codes construction increases the probability of error detection in the data channel and cryptographic devices. Meanwhile, use of spline–wavelets theory for constructing the codes gives the possibility to increase system security from the actions of an attacker. Presented constructions combines spline–wavelets functions and bent functions. Developed robust codes, compared to existing ones, have a higher parameter of maximum error masking probability. Illustrated codes are ensuring the security of transmitted information. Some of the granted constructions were implemented on FPGA.

The observed data of COVID-19 progression in Pakistan for first 50 days from the first patient been reported has shown quite an unusual trend which is in opposition to clear exponential spread pattern of any infectious disease. The data of positive cases of 50 days of disease progression has been collected from COVID-19 dashboard of Pakistan and analyzed to see the graphical trend and to forecast the behaviour of disease progression for next 30 days. Mathematical equations regarding exponential growth are used to analyse the disease progression and different possible trajectories are plotted to understand the approximate trend pattern. The possible projections estimated 20k-456k positive cases within 80 days of disease spread in Pakistan. Although, the disease progression pattern is not perfectly exponential, it is still threatening a major fraction of susceptible population and demands effective strategic planning and control.

Policymakers, academics, and industry players have been focused on determining whether connected health (CH) is a fad or a trend by looking at its sustainability. Although the significance of innovation in healthcare is gradually rising, a definitive identification and systematic comprehension of the core drivers, structure, content, and pattern of innovation in CH are missing. To bridge this gap, this study re-examines and analyses CH from the perspectives of its industrial chain and structure, to assess its future prospects and sustainability by focusing on how its structures and participants act in the ecosystem. This study involves an inductive theory building approach based on multi-stage, semi-structured interviews (n=60 in total). The results indicate that the core drivers, constituents, and components of CH need to be identified and restructured. A valid discourse, which is missing in the current literature, should be proposed with regard to the sustainability of CH. A sustainable business model innovation (BMI) system and the methods employed to achieve sustainability are suggested to discover indicators for future success. This study enriches the current CH understanding from a technology perspective and suggests some implications for practitioners as well as policymakers to enhance sustainable development in the healthcare sector.

A mixture of nonlabeled (14N2H4) and 15N labeled hydrazine (15N2H4) in an aqueous solution is oxidized to 15N2, 14N2, and 14N15N molecules, indicating the intermediate existence of the 14NH2-14NH-15NH-15NH2 with subsequent hydrogen transfers and splitting of side N-N bonds. Structures, thermodynamics, and electron characteristics of various N4H6 molecules in aqueous solutions are investigated using theoretical treatment at the CCSD/cc-pVTZ level of theory to explain the crucial part of the hydrazine oxidation reaction. Most N4H6 structures in aqueous solutions are decomposed during geometry optimization. Splitting the bond between central nitrogen atoms is the most frequent, but the breakaway of the side nitrogen is energetically the most preferred. The N-N fissions are enabled by suitable hydrogen rearrangements. Gibbs free energy data indicate the dominant abundance of NH3... N2... NH3 species. The side N atoms have very high negative charges, which should support hydrogen transfers in aqueous solutions. The only stable cyclo-(NH)4…H2 structure has a too high Gibbs energy and breaks the H2 molecule. The remaining initial cyclic structures are split into hydrazine and HN≡NH or H2N≡N species, and their relative abundance in aqueous solutions is vanishing.

In this study, we have focused on studying the heterogenous degradation kinetics of regarding the decomposition of emergency contraceptive agent levonorgestrel (LNG), which is a second-generation synthetic progestogen that is the active component of the racemic mixture of norgestrel. The degradation processes of the active pharmaceutical ingredient (API) were compared with the ones obtained from model system containing the API along with the excipients that are found in a commercialized pharmaceutical formulation in a mass ratio of 1:1 (LNGMIX), in order to observe if the excipients have a stabilizing or destabilizing effect for the degradation of this progestogen. To achieve this, the following investigational methods were used: FTIR (Fourier transform infrared) spectroscopy and thermal analysis (TG/DTG/DSC analysis). For the kinetic analysis the data obtained from two main decomposition processes observed on the DTG curves were used and processed with a preliminary method, namely ASTM E698 and two isoconversional methods: Friedman and Flynn-Wall-Ozawa. The isoconversional study revealed that the decomposition mechanism of both LNG and LNGMIX are complex, and the excipients have a stabilizing effect over decomposition of API in tablet.

A data-driven analysis method known as dynamic mode decomposition (DMD) approximates the linear Koopman operator on projected space. In the spirit of Johnson-Lindenstrauss Lemma, we will use random projection to estimate the DMD modes in reduced dimensional space. In practical applications, snapshots are in high dimensional observable space and the DMD operator matrix is massive. Hence, computing DMD with the full spectrum is infeasible, so our main computational goal is estimating the eigenvalue and eigenvectors of the DMD operator in a projected domain. We will generalize the current algorithm to estimate a projected DMD operator. We focus on a powerful and simple random projection algorithm that will reduce the computational and storage cost. While clearly, a random projection simplifies the algorithmic complexity of a detailed optimal projection, as we will show, generally the results can be excellent nonetheless, and quality understood through a well-developed theory of random projections. We will demonstrate that modes can be calculated for a low cost by the projected data with sufficient dimension.

We propose a partial information decomposition based on the newly introduced framework of causal tensors, i.e., multilinear stochastic maps that transform source data into destination data. The innovation that causal tensors introduce is that the framework allows for an exact expression of an indirect association in terms of the constituting, direct associations. This is not possible when expressing associations only in measures like mutual information or transfer entropy. Instead of a priori expressing associations in terms of mutual information or transfer entropy, the a posteriori expression of associations in these terms results in an intuitive definition of a nonnegative and left monotonic redundancy, which also meets the identity property. Our proposed redundancy satisfies the three axioms introduced by Williams and Beer. Symmetry and self-redundancy axioms follow directly from our definition. The data processing inequality ensures that the monotonicity axiom is satisfied. Because causal tensors can describe both mutual information as transfer entropy, the partial information decomposition applies to both measures. Results show that the decomposition closely resembles the decomposition of other another approach that expresses associations in terms of mutual information a posteriori. A negative synergistic term could indicate that there is an unobserved common cause.

Prevalence of overweight and obesity are escalating globally among the general population. However, there are limited evidence on the trends and prevalence of overweight /obesity in the military setting. Increased rates of injuries, low work productivity, incurred higher healthcare costs and prematurely discharge from service are consequences of overweight/obesity among the military. Therefore, we aimed to systematically describe the trends and prevalence of overweight and obesity in the military population, by regions and military service branches. Databases including PubMed, Scopus, Web of Science and Google Scholar were used. Inclusion criteria were military population (inclusive of all service branches) with BMI reported as the overweight/obesity indicator. Population related to military but not exclusively military personnel such as the retirees, the veterans and their dependents were excluded. From the 27 included studies, 13 were published between year 2010 to 2014 and half were conducted in the United States. Overall, studies showed increasing trend in the prevalence of overweight (30% to 50%) and obesity (2% to 30%); only one study showed a decreasing trend of 0.9% and 0.6% for the prevalence of overweight and obesity respectively. However, the rates of increment differed between countries, where Asian countries demonstrated lower overweight prevalence compared to the United States and the European countries. In conclusion, the military population is not protected from overweight and obesity. Interventions should be implemented to prevent overweight / obesity among the military personnel.

The article reviews the constituent’s physico-chemical parameters in the water of the Mansagar Lake of the Jaipur City. The water quality is also investigated using evaluated physico-chemical parameters with in-depth study of their distribution as per sample location-wise and season-wise. A detailed discussion on the associationship among parameters (pH, Conductivity, turbidity, dissolved Oxygen, chemical and Biochemical Oxygen demand, etc.) using the Pearson’s analytical method is also presented. The strength of the article is the graphical presentation of evaluated physico-chemical parameters and the water quality indices for sample station-wise and the season-wise. To our best of understanding, first time such details have been clubbed together and discussion in brief for studied lake.

Urbanization and industrialization processes in Mongolia have been significant and rapid for the last half-century. During this period, changes in political and economic systems, growth in the population, and the occasional harsh climate conditions were subject to fluctuations in the natural resource usage. The total Ecological Footprint (EF) in Mongolia has increased from 6.8 million global hectares (gha) in 1961 to 14.6 million gha in 2012. However, Biocapacity (BC) has decreased from 50.6 million gha in 1961 to 39.0 million gha in 2012. The study shows that grazing land Footprint and carbon uptake land Footprint are the two major contributors of the recent intensified use of biological resources. To ensure stable economic development and sustainable use of natural resources, environmental planning is required to consider both the population’s pressure on the environment and the ecosystem’s regeneration capacity, simultaneously. We have proposed a few possible strategies for sustainable utilization of grazing land Footprint and carbon Footprint. For grazing land Footprint, efficient management of both herding practice and number of animals should be considered. In case of carbon Footprint, it is estimated that with the improved combustion efficiencies of coal-based power plants and the maximum use of renewable energy, carbon dioxide (CO₂) emissions in Mongolia can be reduced up to 30% compared to the base line business as usual case in 2030.

In fuzzy decision problems, the ordering of fuzzy numbers is the basic problem. Among which, the fuzzy preference relation is the reasonable one to represent preference relation by a fuzzy membership function. This paper studies the Nakamura’s and Kołodziejczyk’s preference relations. Eight cases of representing different level of overlapping between two triangular fuzzy numbers are considered. We analyze the ranking behaviors of all possible combinations of decomposition and intersection of two fuzzy numbers for the Nakamura’s and Kołodziejczyk’s preference relations of these test cases. The results indicate that the decomposition and intersection can affect the fuzzy preference relations, thereby the final total order relation of fuzzy numbers.

The rapid expansion of China's A-share market, coupled with the burgeoning volume of financial research reports, presents a unique challenge to traditional stock price prediction methodologies. This study introduces FAST-SCAN, a novel framework designed to leverage natural language processing (NLP) and time series analysis for the efficient and accurate prediction of stock market trends. By integrating advanced sentiment analysis, primarily through the utilization of the RoBERTa model, with dynamic time series forecasting, FAST-SCAN aims to distill actionable insights from the vast corpus of financial research reports. This approach not only enhances the speed and efficiency of financial analysis but also addresses the time-sensitive nature of market-influencing factors, thereby providing a competitive edge in stock price prediction. The framework demonstrates a notable improvement in predictive performance, achieving a 20% annualized return and a 7.19% RankIC, marking a significant advancement over conventional statistical analysis methods. Through its innovative combination of NLP and predictive analytics, FAST-SCAN paves the way for a more informed and strategic approach to investment in the A-share market, emphasizing the importance of timely, data-driven decision-making in the financial industry.

Study of spatiotemporal dynamics of temperature is vital to assess changes in climate, especially in the Himalayan region where livelihoods of billions of people living downstream depends on water coming from the melting of snow and glacier ice. To this end, temperature trend analysis is carried out in Narayani river basin, a major river basin of Nepal characterized by three climatic regions: tropical, subtropical and alpine. Temperature data from six stations located within the basin were analyzed. The elevation of these stations ranges from 460 to 3800 m a.s.l. and the time period of available temperature data ranges from 1960–2015. Multiple regression and empirical mode decomposition (EMD) methods were applied to fill in missing data and to detect trends. Annual as well as seasonal trends were analyzed and a Mann-Kendall test was employed to test the statistical significance of detected trends. Results indicate significant cooling trends before 1970s, and warming trends after 1970s in the majority of the stations. The warming trends range from 0.028 ∘" style="position: relative;">∘C year−1" style="position: relative;">−1 to 0.035 ∘" style="position: relative;">∘C year−1" style="position: relative;">−1 with a mean increasing trend of 0.03 ∘" style="position: relative;">∘C year−1" style="position: relative;">−1 after 1971. Seasonal trends show highest warming trends in the monsoon season followed by winter, pre-monsoon, and the post-monsoon season. However, difference in warming rates between different seasons was not significant. An average temperature lapse rate of −0.006 ∘" style="position: relative;">∘C m−1" style="position: relative;">−1 with the steepest value (−0.0064 ∘" style="position: relative;">∘C m−1" style="position: relative;">−1) in pre-monsoon season and least negative (−0.0052 ∘" style="position: relative;">∘C m−1" style="position: relative;">−1) in winter season was observed for this basin. A comparative analysis of the gap-filled data with freely available global climate datasets show reasonable correlation thus confirming the suitability of the gap filling methods.

Control And Data Acquisition (SCADA) systems currently monitor and collect a huge among of data from all kind of processes. In practice, due to sensor failures or to communication errors, in the long-time running, some data may be lost. When it happens, given the nature of these failures, information is lost in bursts, that is, sets of consecutive samples, which besides can be very long. Data completion is a critical step, which must be done with the utmost rigour in order to not propagate errors in the rest of the processing chain stages. Some Big Data techniques do not work if the data series are incomplete, due to the loss of some data. When this occurs it is necessary to fill out the gaps of the historical data with a reliable data completion method. This paper presents an ad-hoc method to replenish the data lost by a SCADA system in case of long bursts. The data correspond to levels of drinking water tanks of a Water Network company that present patterns on a daily and a weekly scale. A method based on tensors is used to take advantage of the data structure. A specially designed \textit{tensorization} is employed to deal with bursts of missed data, applying a twice tensor decomposition and a signal continuity correction. Statistical tests are realized, which consist of apply the data reconstruction algorithms, by deliberately removing bursts of data in verified historical database servers, to be able to evaluate the real effectiveness of the tested methods. For this application, the presented approach outperforms the other techniques found in the literature.

The author attempts to reconstruct the climatic vicissitudes of the Mediterranean to explain why only broadly distributed Eurasian forest species have penetrated the Mediterranean peninsulas. He has carried out a bibliographic survey of the status of breeding forest birds in Italy over 15 decades (1872-2022) in order to establish an objective long-term trend (stable, increasing, decreasing, etc.). The number of breeding forest birds in Italy amounts to 61; their distribution, with a few exceptions, indicates that they are widespread in Eurasia, but only a small percentage of Eurasian forest species have colonized Italy and the other Mediterranean peninsulas, namely 49 in Iberian, 61 in Italian and 64 in Balkan peninsulas; a small percentage of them (between 10.9 and 14.3%) belongs to trans-Saharan migrants. The similarity between the forest species on the three peninsulas (Iberian, Italian and Balkan) results between 0.45 and 0.48, indicating a certain differ-ence in the overall fauna on the three territories. Not all species have penetrated southwards into the three peninsulas; for example, some that stopped in the Italian Alps have instead arrived to the forests of Greece, at a latitude corresponding to southern Italy, or species that in Italy stopped in the northern Apennines in the other two peninsulas have instead arrived far south. Iberian peninsula and the island of Corsica hold three endemic species among breeding forest birds, Italian and Balkan peninsulas have not endemic species. Overall, the Mediterranean presently hosts mainly neo-endemic taxa among forest bird species; the only paleo-endemics can be considered the three species of nuthatches living in Corsica, Algeria, and Turkey (other than Caucasus and the islet of Lesvos) and Le Vaillant’s woodpecker in the Maghreb (North Africa). Italian forests cover ca. 40% of land surface and since 1980’ are increasing, but 22% of them do not have a natural origin. However, it is difficult to know the true increase of forests, because some of them are fired every year. The presence of some ecologically demanding forest birds depends on the age of the trees, permanent open spaces and other characteristics at the edge of woodland.

Disasters related to climate change on our water resources are on the rise in terms of scale and severity. Therefore, predicting groundwater levels (GWL) is a crucial means to aid adaptive capacity towards disasters related to climate change in our water resources. In this study Gradient Boosting (GB) regression modelling approach for GWL prediction as a function of rainfall and antecedent GWL is used. Firstly, we sought to demonstrate the effects of rainfall changes on our groundwater resources through a Mann-Kendall trend analysis. Secondly, we evaluated the relationship between the input and response variables and determined the optimal lag times between the variables using autocorrelations and cross-correlations. Lastly a predictive model was developed for eight groundwater stations in the Upper Crocodile. 50 % of the groundwater stations revealed declining trends, while 25% had no trends and the other 25% showed an increasing trend. Generally low cross-correlation maximum (CCmax) were obtained, with the highest CCmax being 0.299 at an optimal lag of 2-month. While the highest autocorrelation was 0.969 at a 1-month lag. The best groundwater predictive model had R2 and MSE of 0.66 and 0.06, respectively. The stations that generally performed better had both high autocorrelation and cross-correlation coefficients. GB model performed satisfactorily in predicting GWL for most of the stations in the study area. Therefore, GB can be used for GWL prediction in the Upper Crocodile.

Trend patterns of melanoma skin in Serbia from 1999 to 2020 *Rancic K. Natasa 1,2, Tiodorovic B. Danica 1,4, Ilic V. Mirko 2, Biljana N. Kocic 1,2, Maksimovic S. Natasa 3, Ilija D. Kocic 4, Dusan P. Miljkovic 4, Otasevic A. Suzana 1,2 Introduction. Melanoma of the skin represents about 1% of all skin cancers and it causes nearly 80% of skin cancer deaths. Due to its increasing incidence, particularly in the most developed countries it represents a great challenge for primary prevention. Objective. To explore patterns and analyze incidence trends of melanoma in Central Serbia from 1999 to 2020. Materials and Methods. Descriptive study was done and data were obtained from the Population-based Cancer Registry of Serbia. The joinpoint regression analysis was done to assess the incidence trend of the melanoma skin: the annual percent change (APC) along with its 95% confidence interval (95% CI) was calculated. Results. A total number of 9952 new melanoma cases were registered melanoma (5204 in males and 4748 in females) during the observed period. Males represented 52.3% of all patients, with male to female ratio of incidence 2.09:1. A non significant increasing trend of incidence in males from 1999 to 2013 with APC of 2.53% (95%CI: from -18.2 to 21.9, p=1) and significantly increasing trend from 2013 to 2020 with the APC of 11.29 % (95%CI: from 1.4 to 5.8, p<0.001) was established. An incidence trend in females has stabilized in the whole studied period, with APC of 0.42% (95%CI: from -3.3 to 6.8, p=0.1). Melanoma of the skin was not common before the age of 30. Out of all cases and about of 76% new cases were diagnosed in persons ≥ 50 years of age. Conclusion. The incidence trend of new melanoma cases significantly increase in the whole population from 1999 to 2020. The significant increasing of incidence trend in males and stabilization of incidence trend in females was established. Males had significantlly higher incidence rates than femalesand over of 76% new melanoma cases were diagnosed in persons above 50 years of age.

Abstract Depending upon altitudinal gradient in the Himalayas, the rate of climate change varies from lowland to upland. The Chitwan Annapurna Landscape (CHAL) is the central part of the Himalayas and covers all bioclimatic zones. Analysis of time series data (1970-2019) of temperature and precipitation was carried out in seven bioclimatic zones extending from lowland Terai to higher Himalayas. The non-parametric Mann-Kendall test was applied to determine the trend, which was quantified by Sen’s slope. Annual and decade interval average temperature, precipitation trends, and lapse rate were analyzed in each bioclimatic zone. Out of seven bioclimatic zones, four zones showed a decreasing precipitation trend (lower tropical, upper tropical, upper subtropical, and alpine bioclimatic zones)at the rate of 1.8, 1.98, 2.06, and 1.80 mm/year, and in lower sub-tropical, temperate, and lower subalpine bioclimatic zones, increasing at the rate of 0.45, 1.81 and 1.28mm/year, respectively. Precipitation did not show any particular trend at decade intervals. The average annual temperature at different bioclimatic zones clearly indicates that temperature at higher elevations is significantly increasing more than at lower elevations. In lower tropical bioclimatic zone (LTBZ), upper tropical bioclimatic zone(UTBZ), lower subtropical bioclimatic zone (LSBZ), upper subtropical bioclimatic zone(USBZ), and temperate bioclimatic zone(TBZ), the average temperature increased by 0.022, 0.030, 0.036, 0.042 and 0.051oC/year, respectively. The decade level temperature scenario revealed that the hottest decade was from 1999-2009. The average temperature was found as 24.1, 21.8, 19.7, 17.5, and 13.3oC in LTBZ, UTBZ, LSBZ, USBZ, and TBZ, respectively, and the average annual precipitation in LTBZ, UTBZ, LSBZ, USBZ, TBZ, LBZ, and ABZ was 2002.1, 2613.1, 2223.9, 3146.9, 1447.2, 952.1, and 361.7mm/year, respectively, in CHAL. With the impact of climate change site and region-specific, this information highlights the need to mitigate climate change in different bioclimatic zones.

Water quality forecasting is increasingly significant for agricultural management and environmental protection. Enormous amounts of water quality data are increasingly being collected by advanced sensors, which leads to an interest in using data-driven models for predicting trends in water quality. However, the unpredictable background noises introduced during water quality monitoring seriously degrade the performance of those models. Meanwhile, artificial neural networks (ANN) with feed-forward architecture lack the capability of maintaining and utilizing the accumulated temporal information, which leads to biased predictions in processing time series data. Hence, we propose a water quality predictive model based on a combination of Kernal Principal Component Analysis (kPCA) and Recurrent Neural Network (RNN) to forecast the trend of dissolved oxygen. Water quality variables are reconstructed based on kPCA method, which aims to reduce the noise from the raw sensory data and preserve actionable information. With the RNN's recurrent connections, our model can make use of the previous information in predicting the trend in the future. Data collected from Burnett River, Australia was applied to evaluate our kPCA-RNN model. The kPCA-RNN model achieved R2 scores up to 0.908, 0.823 and 0.671 for predicting the concentration of dissolved oxygen in the upcoming 1, 2 and 3 hours, respectively. Compared to current data-driven methods like ANN and SVR, the predictive accuracy of the kPCA-RNN model was at least 8 %, 17 % and 21 % better than the comparative models in these 3 cases. The study demonstrates the effectiveness of the kPAC-RNN modeling technique in predicting water quality variables with noisy sensory data.

Industrial dynamical systems often exhibit multi-scale response due to material heterogeneities, operation conditions and complex environmental loadings. In such problems, it is the case that the smallest length-scale of the systems dynamics controls the numerical resolution required to effectively resolve the embedded physics. In practice however, high numerical resolutions is only required in a confined region of the system where fast dynamics or localized material variability are exhibited, whereas a coarser discretization can be sufficient in the rest majority of the system. To this end, a unified computational scheme with uniform spatio-temporal resolutions for uncertainty quantification can be very computationally demanding. Partitioning the complex dynamical system into smaller easier-to-solve problems based of the localized dynamics and material variability can reduce the overall computational cost. However, identifying the region of interest for high-resolution and intensive uncertainty quantification can be a problem dependent. The region of interest can be specified based on the localization features of the solution, user interest, and correlation length of the random material properties. For problems where a region of interest is not evident, Bayesian inference can provide a feasible solution. In this work, we employ a Bayesian framework to update our prior knowledge on the localized region of interest using measurements and system response. To address the computational cost of the Bayesian inference, we construct a Gaussian process surrogate for the forward model. Once, the localized region of interest is identified, we use polynomial chaos expansion to propagate the localization uncertainty. We demonstrate our framework through numerical experiments on a three-dimensional elastodynamic problem

With advances in Building Information Modeling (BIM), Virtual Reality (VR) and Augmented Reality (AR) technologies have many potential applications in the Architecture, Engineering, and Construction (AEC) industry. However, the AEC industry, relative to other industries, has been slow in adopting AR/VR technologies, partly due to lack of feasibility studies examining the actual cost of implementation versus an increase in profit. The main objectives of this paper are to understand the industry trends in adopting AR/VR technologies and identifying gaps within the industry. The identified gaps can lead to opportunities for developing new tools and finding new use cases. To achieve these goals, two rounds of a survey at two different time periods (a year apart) were conducted. Responses from 158 industry experts and researchers were analyzed to assess the current state, growth, and saving opportunities for AR/VR technologies for the AEC industry. The findings demonstrate that older generations are significantly more confident about the future of AR/VR technologies and they see more benefits in AR/VR utilization. Furthermore, the research results indicate that Residential and commercial sectors have adopted these tools the most, compared to other sectors and institutional and transportation sectors had the highest growth from 2017 to 2018. Industry experts anticipated a solid growth in the use of AR/VR technologies in 5 to 10 years, with the highest expectations towards healthcare. Ultimately, the findings show a significant increase in AR/VR utilization in the AEC industry from 2017 to 2018.

Plants and its corresponding botanical preparations have been used for centuries due to their remarkable potentialities in both treatment and prevention of numerous affections. Hundreds of biologically active constituents are present in each whole plant matrice, working in synergism and conferring both its own protection against invaders and even providing promissory bioactive effects for human beings. The worldwide population has devoted increasing attention and preference by medicinal plants use for health promotion and disease prevention, and more recently for oxidative-stress related disorders protection. Indeed, oxidative stress-related disorders, like cardiovascular and (neuro) degenerative disorders, and even cancer have raised exponentially. Although oxidative stress is in itself intrinsic to our own metabolism, allarming sources of free radicals are daily affecting us. In fact, plant-derived bioactives present a broad spectrum of biological effects, and its antioxidant, anti-inflammatory and more recently anti-aging effects have been considered a hot topic among the medical and scientific community. Nonetheless, and although its numerous biological effects, it should not also be forgotten that some bioactive molecules are prone to oxidation and can even exert pro-oxidant effects. In this sense, the objective of the present review is to provide a detailed overview on plant-derived bioactives in oxidative stress-related disorders. Specifically, the role of phytochemicals as antioxidants and pro-oxidant agents is carefully addressed, as is its therapeutic relevance in disease prevention. Finally, an eye-opening look in overall evidence in humans is also ensured.

Organophosphate pesticides are used in large quantities. However, they exhibit toxic effects on non-target organisms. Dimethoate and its oxo-analog omethoate inhibit acetylcholinesterase and are toxic for mammals. Moreover, they show extreme toxicity for bees. Once in the environment, they undergo chemical transformations and decomposition. We show that dime-thoate and omethoate decompose rapidly in alkaline aqueous solutions (half-lives 5.7 and 0.89 days) but are highly stable in acidic solutions (half-lives 124 and 104 days). These differences are explained using quantum chemical calculations, indicating that a weaker P–S bond in omethoate is more susceptible to hydrolysis, particularly at a high pH. The toxicity of these pesticides solutions decreases over time, indicating that no or very little highly toxic omethoate is formed during hydrolysis. Presented data can be used to predict dimethoate and omethoate concentrations in contaminated water depending on pH. Presented results suggest that alkaline hydrolysis of organophosphates has an advantage over other techniques for their removal since there is no risk of omethoate accumulation and increased toxicity of contaminated water.

China is a traditional agricultural country, and the integration of rural industries has become an essential policy direction for the current strategy of agricultural modernization in China. In recent years, the agricultural industrial chains across various regions of China have consistently expanded and extended. The multifunctionality of agriculture is continuously unearthed, and the principal entities managing agriculture have become increasingly diversified and have grown significantly. New industries and forms in agriculture emerge incessantly. Accurately and profoundly understanding the inherent features of the integration of industries in rural China, establishing a scientific and rational measurement index system in line with the current status and development goals of rural China, and employing appropriate measurement methods to assess its development level and process, is instrumental in comprehending the level of integrated development in various regions. This aids in identifying challenges in the developmental process and proposing targeted developmental strategies. Hence, this paper, rooted in the integration of rural industries, cross-industry, industry extension, industry agglomeration, and industry penetration, sets up an measurement index system. Using provincial panel data from 2011 to 2020, the paper measures the level of integrated development in rural industries across China and its 31 provinces. Based on the measurement results, further techniques such as kernel density estimation and Gini coefficient decomposition have been used to analyze the spatial distribution characteristics and dynamic trends of the integrated development of rural industries in China. Research indicates that during the sample period, the overall level of integrated development in rural industries in various provinces in China has shown an upward trend. Development among the eastern, central, and western regions is highly uneven, but this disparity has been gradually narrowing in recent years. Furthermore, the levels of integrated development in different provinces exhibit significant spatial agglomeration effects. The development level of neighboring regions significantly impacts the province's development status. In the process of integrated development of rural industries in China, there's a trend where "it's easier to downgrade than to upgrade," with very few regions achieving leapfrog development.

This study aims to identify the knowledge structure and research trends of soccer psychology research during the last 33 years (1990–2022). Data were obtained from 1,863 papers from the Web of Science database. The data were collected through keyword text mining and data preprocessing to determine the keywords needed for analysis. Based on the keywords, latent Dirichlet allocation-based topic modeling analysis was performed to analyze the topic distribution of papers and explore research trends by topic area. The topic modeling process included four topic area and fifty topics. The “Coaching Essentials in Football” topic area had the highest frequency, but it was not statistically identified as a trend. However, coaching, including training, is expected to continue to be an important research topic, as it is a key requirement for success in the highly competitive elite football world. Interest in the research field of “Psychological Skills for Performance Development” has waned in recent years. This may be due to the predominance of other subject areas rather than a lack of interest. Various high-tech interventions and problem-solving attempts are being made in this field, providing opportunities for qualitative and quantitative expansion. “Motivation, cognition, and emotion” is a largely underrated subject area in soccer psychology. This could be because survey-based psychological evaluation attempts have decreased as the importance of rapid field application has been emphasized in recent soccer-related studies. However, measuring psychological factors contributes to the study of football psychology through a new methodology and theoretical background. Recognizing the important role of psychological factors in player performance and mental management, as well as presenting new research directions and approaches that can be directly applied to the field, will advance soccer psychology research.

The purpose of the study is to control the ratio of programs of different genres when forming the broadcast grid in order to increase and maintain the rating of the channel. In the multichannel environment, television rating control consists of selecting such content, ratings of which are completely restored after advertising. A hybrid approach combining the benefits of semantic training and fuzzy relational equations in simplification of the expert recommendation systems construction is proposed. The problem of retaining the television rating can be attributed to the problems of fuzzy resources control. The increase or decrease trends of the demand and supply are described by primary fuzzy relations. The rule-based solutions of fuzzy relational equations connect significance measures of the primary fuzzy terms. Rules refinement by solving fuzzy relational equations allows avoiding labor-intensive procedures for the generation and selection of expert rules. The solution set generation corresponds to the granulation of the television time, where each solution represents the time slot and the granulated rating of the content. In automated media planning, generation of the weekly TV program in the form of the granular solutions provides the decrease of the time needed for the programming of the channel broadcast grid.

Ab initio density functional theory molecular dynamics extensive calculations were used for the first time to evaluate stability conditions for relevant phases of InN. In particular, thermal decomposition of InN with formation of N2 molecules and pressure induced wurtzite – rocksalt solid-solid phase transition were established. The results consistent with available experimental data allowed a critical evaluation of potential and limitations of the proposed simulation method. The ab initio molecular dynamics as an efficient tool for simulations of phase transformations of InN including solid-solid structural transition and thermal decomposition with formation of N2 molecules has been demonstrated. It is of high interest because InN being important component of epitaxial quantum structures has still not been obtained as a bulk single crystal making difficult a determination of its basic physical properties and designing new applications.

In view of the problem that the hot and cold loads of mushroom houses are affected by multiple factors such as environment, mushrooms, and equipment, which are difficult to accurately model, this paper proposes a short-term load prediction method based on empirical wavelet transform (EWT) and mixed autoregressive integrated moving average (ARIMA) and convolutional bi-directional short- and long-term attention mechanism (CNN-BiLSTM-Attention). The method first uses the Boruta algorithm to filter the input characteristics, and then uses the EWT method to decompose the mushroom house load data into 4 modal components. Then the Lempel-Ziv method is introduced to divide the modal components into two categories of high and low frequencies, and the CNN-BiLSTM-Attention and ARIMA prediction models are constructed separately. Finally, the two types of prediction results are superimposed and reconstructed to obtain the final load prediction value. The test results show that the Boruta algorithm can effectively filter out the characteristics of key influencing factors. Compared with the Spearman and Pearson correlation coefficient methods, the mean absolute error (MAE) of the prediction results is reduced by 14.72% and 3.75%, respectively; compared with the ensemble empirical mode decomposition (EEMD) method, the EWT method can increase the decomposition and reconstruction error by 103 orders of magnitude, which can effectively improve the prediction accuracy of the model; compared with the individual neural network model, the prediction effect of the model proposed in this paper has obvious advantages, and the MAE, root mean square error (RMSE) and mean absolute percentage error (MAPE) of the prediction results are reduced respectively. 31.06%, 26.52% and 39.27%.

Information theory provides robust measures of multivariable interdependence, but classically does little to characterize the multivariable relationships it detects. The Partial Information Decomposition (PID) characterizes the mutual information between variables by decomposing it into unique, redundant, and synergistic components. This has been usefully applied, particularly in neuroscience, but there is currently no generally accepted method for its computation. Independently, the Information Delta framework characterizes non-pairwise dependencies in genetic datasets. This framework has developed an intuitive geometric interpretation for how discrete functions encode information, but lacks some important generalizations. This paper shows that the PID and Delta frameworks are largely equivalent. We equate their key expressions, allowing for results in one framework to apply towards open questions in the other. For example, we find that the approach of Bertschinger et al. is useful for the open Information Delta question of how to deal with linkage disequilibrium. We also show how PID solutions can be mapped onto the space of delta measures. Using Bertschinger et al. as an example solution, we identify a specific plane in delta-space on which this approach’s optimization is constrained, and compute it for all possible three-variable discrete functions of a three-letter alphabet. This yields a clear geometric picture of how a given solution decomposes information

Glucose-sensitive films were prepared by the layer-by-layer (LbL) deposition of poly(ethyleneimine) (H-PEI) solution and DNA solution (containing glucose oxidase (GOx)). H-PEI/DNA+GOx multilayer films were constructed using electrostatic interactions. The (H-PEI/DNA+GOx)5 film was then partially decomposed by hydrogen peroxide (H2O2). The mechanism for the decomposition of the LbL film was considered to involve a more reactive oxygen species (ROS) that was formed by the reaction of hemin and H2O2, which then caused nonspecific DNA cleavage. GOx present in the LbL films reacts with glucose to generate hydrogen peroxide. Therefore, decomposition of the H-PEI/DNA+GOx)5 film was observed when the thin film was immersed in a glucose solution. A (H-PEI/DNA+GOx)5 film exposed to a glucose solution for periods of 24, 48 72, and 96 h indicated decomposition of the film increased with the time. The rate of LbL film decomposition increased with the glucose concentration. At pH and ionic strength close to physiological conditions, it was possible to slowly decompose the LbL film at a sub-millimolar glucose concentration.

Abstract: A recent approach to radiotherapy for prostate cancer is the administration of high doses of radiation to the prostate while minimizing the risk of side effects. Thus, image-guided radiotherapy utilizes advanced imaging techniques and is a feasible strategy for increasing the radiation dose. New radioactive particles are another approach to achieving high doses and safe procedures. Prostate brachytherapy is currently considered as a combination therapy. Spacers are useful to protect adjacent organs, specifically the rectum, from excessive radiation exposure.

The article is aimed at a brief comparison and analysis of the results of queries to IEEE Xplore and the leading abstract databases Scopus and Web of Science to identify research trends. Some errors in the Author Keywords in Web of Science have been revealed. Therefore, a more detailed analysis was conducted by comparing different types of key terms for IEEE Xplore and Scopus platforms only. I used IEEE Access journal metadata as indexed on both platforms. The sample match for IEEE Xplore and Scopus was achieved by comparing DOI. The IEEE Xplore metadata contains more types of key terms, which provides an advantage in analyzing research trends. Using NSPEC Controlled Terms from expert-compiled vocabulary provides a more stable data, which gives an advantage when considering the change of terms over time. Apriori, an algorithm for finding association rules, has been used to compare co-occurrence of terms for a more detailed description of sample subjects on both platforms. VOSviewer was used to analyze trends in scientific research based on IEEE Xplore data. The 2011-2021 ten-year period was divided into two sub-intervals for comparing the occurrence of Author Keywords, IEEE Terms, and NSPEC Controlled Terms. Using the IEEE conference proceedings bibliometric data, I illustrated the importance of context in estimating the rate of growth of publishing activity on a topic of interest.

This paper is an attempt to present a COVID-19 prediction model for India. Lockdown plays an important role in the arrest of community spread of the disease. This was evident from the study of other countries such as Russia, Belgium and Germany, where peak cases were recorded within a month of the imposition of lockdown, that it showed an immediate positive effect. However, in India, even after 65 days of lockdown, there is no decrease in the number of daily new cases reported. There were many models prepared for India and almost all of them were proven wrong by the increase in the number of cases. The model in this paper is prepared using the COVID-19 trend in other countries, population density and the pandemic bell curve. Based on the available data until 24^th May 2020, two scenarios have been presented. In one, the peak shall be obtained when the number of daily new cases per million reaches 190 and in the second when the daily new cases per million reach 724. One model predicts the number of cases to reach 1 million by mid-July 2020. The other model predicts the number of cases to peak by mid-July with the total cases reaching 20 million. The predicted cases were compared with the actual cases recorded for the period 25^th May to 11^th June 2020. It was observed that the actual values matched quite reasonably with the predicted values.

GRACE-derived Terrestrial Water Storage Anomalies (TWSA) continue to be used in an expanding array of studies to analyze numerous processes and phenomena related to terrestrial water storage dynamics, including groundwater depletions, lake storage variations, snow, and glacial mass changes, as well as floods, droughts, among others. So far, however, few studies have investigated how the factors that affect total water storage (e.g., precipitation, runoff, soil moisture, evapotranspiration) interact and combine over space and time to produce the mass variations that GRACE detects. This paper is an attempt to fill that gap and stimulate needed research in this area. Using the Nile River Basin as case study, it explicitly analyzes nine hydroclimatic and anthropogenic processes, as well as their relationship to TWS in different climatic zones in the Nile River Basin. The analytic method employed the trends in both the dependent and independent variables applying two geographically multiple regression (GMR) approaches: (i) an unweighted or ordinary least square regression (OLS) model in which the contributions of all variables to TWS variability are deemed equal at all locations; and (ii) a geographically weighted regression (GWR) which assigns a weight to each variable at different locations based on the occurrence of trend clusters, determined by Moran’s cluster index. In both cases, model efficacy was investigated using standard goodness of fit diagnostics. The OLS showed that trends in five variables (i.e., precipitation, runoff, surface water soil moisture, and population density) significantly (p<0.0001) explain the trends in TWSA for the basin at large. However, the models R2 value is only 0.14. In contrast, the GWR produced R2 values ranging between 0.40 and 0.89, with an average of 0.86 and normally distributed standard residuals. The models retained in the GWR differ by climatic zone. The results showed that all nine variables contribute significantly to the trend in TWS in the Tropical region; population density is an important contributor to TWSA variability in all zones; ET and Population density are the only significant variables in the semiarid zone. This type of information is critical for developing robust statistical models for reconstructing time series of proxy GRACE anomalies that predate the launch of the GRACE mission and for gap-filling between GRACE and GRACE-FO.

The New Zealand housing sector is experiencing rapid growth that boosts the national economy but also results in the loss of valuable resources. In line with the growth, the housing market for both residential and business purposes has been booming, as have house prices. To sustain the housing development, it is critical to accurately monitor and predict housing prices so as to support the decision-making process in housing sector. This study is devoted to applying a mathematical method to predict housing prices. The forecasting performance of two types of models: ARIMA and multiple linear regression analysis are compared. The ARIMA and regression models are developed based on a training-validation sample method. The results show that the ARIMA model generally performs better than the regression model. However, the regression model explores, to some extent, the significant correlations between house prices in New Zealand and the macro-economic conditions.

We studied the dynamics of stable carbon (δ13C) and nitrogen (δ15N) isotopes in litters from Norway spruce (NSL) (Picea abies) and Scots pine (SPL) (Pinus silvestris) during in situ decomposition over a period of more than 4 years. Relative to initial values, δ13CNSL showed a weak enrichment (0.33‰), whereas δ13CSPL resulted in depletion (-0.74‰) at the end of decomposition. Both litter types experienced a depletion in δ15N during decomposition; δ15NNSL decreased by -1.74‰ and δ15NSPL decreased by -1.99‰. The effect of the selective preservation of or acid unhydrolyzable residue (AUR) in lowering δ13C of the residual litter was evident only in SPL. In the NSL, only in the initial stage C/N had a large effect on the δ13C values. In the later stages, there was a non-linear decrease in δ13CNSL with a simultaneous increase in AUR concentrations , but the effect size was large, suggesting the role of lignin in driving δ13C of residues in later stages. Depletion in 15N of the residual litters concomitant with the increase in N concentration suggests bacterial transformation of the litter over fungal components. A consistent decline in δ15N values further implies that bacterial dominance prompted this by immobilizing nitrate depleted in 15N in the residual litter.

Nowadays, it is highly desired to develop highly active and humidity resistive ozone decomposition catalyst to eliminate the ozone contaminant, one of the primary pollutants in air. In this work, a series of Cu2S hollow structured materials are rapidly synthesized using different structured Cu2O templates. The Cu2S from porous Cu2O shows the highest ozone catalytic decomposition efficiency of >95% to 400 ppm ozone with a weight hourly space velocity of 480,000 cm3g-1h-1 in dry air. Importantly, the conversion still keeps >85% in a high relative humidity of 90%. The mechanism is explored by diffusive reflectance infrared spectroscopy which shows the decomposition intermediate of O22-, and the X-ray photoelectron spectroscopy reveals the dual active site of both Cu and S. All these results show the effective decomposition of ozone by Cu2S especially in harsh environments, promising for active ozone elimination.

A rigorous perturbation analysis of the singular value decomposition of a real matrix of full column rank is presented. It is shown that the SVD perturbation problem is well posed only in case of distinct singular values. The analysis involves the solution of coupled systems of linear equations and produces asymptotic (local) componentwise perturbation bounds of the entries of the orthogonal matrices participating in the decomposition of the given matrix and of its singular values. Local bounds are derived for the sensitivity of the singular subspaces measured by the angles between the unperturbed and perturbed subspaces. An iterative scheme is described to find global bounds on the respective perturbations. The analysis implements the same methodology used previously to determine componentwise perturbation bounds of the Schur form and the QR decomposition of a matrix.

A new method in which completely eliminated the negative value of the scattering power is proposed in this paper. Primarily, here are presented the Freeman-Durden decomposition of the scattering powers, which are computed by using the coherency matrix elements with rotation and without rotation. Secondly, this paper investigates the reasons of the occurrence of negative values of the scattering powers. Then using the modification like in algorithm proposed by Yamaguchi for G4U, it was applied for the algorithm of Freeman-Durden decomposition to eliminate negative values. In this research, Radarsat-2 radar remote sensing data were used, which are acquired for study area Yushu County, Qinghai province, China. At the end, the comparison results of Yamaguchi G4U and a modified Freeman-Durden decompositions were presented.

A highly-integrated experimental system for plasma decomposition of fuels was built. Experiments were conducted and confirmed that macromolecular chain hydrocarbons were cracked by large-gap dielectric barrier discharge under the excitation of a microsecond-pulse power supply. Alkanes and olefins with a C atom number smaller than 10 as well as hydrogen were found in the cracked products of n-decane (n-C10H22). The combination of preheating and plasma decomposition had strong selectivity for olefins. Under strong discharge conditions, micromolecular olefins were found in the products. Moreover, there was a general tendency that micromolecular olefins gradually accounted for higher percentage of products at higher temperature and discharge frequency.

In order to realize the performance degradation trend prediction accurately, a prediction method based on multi-domain features and temporal convolutional network (TCN) is proposed. Firstly, construct a high-dimensional feature set in the multi-domain of vibration signals, and use comprehensive evaluation indicators to preliminarily screen performance degradation indexes with good sensitivity and strong trend. Secondly, the kernel principal component analysis (KPCA) method is adopted to eliminate redundant information between multi-domain features, and construct a health index (HI) based on convolutional auto-encoder (CAE) network. Thirdly, a TCN-based performance degradation trend prediction model is constructed, and direct multi-step prediction is used to predict the performance degradation trend of the monitored object. On this basis, the validity of the proposed method is verified using the bearing public data, and it is successfully applied to performance degradation trend prediction of rolling contact fatigue specimen. The results show that the feature set can be reduced from 14 dimensions to 4 dimensions by using KPCA, while 98.33% of the information of the original feature set is retained. Furthermore, the method of constructing HI based on CAE network is effective. The change process of the HI constructed truly reflects the performance degradation process of the rolling contact fatigue specimen. Compared with the two commonly used HI construction methods, auto-encoding (AE) network and gaussian mixture model (GMM), this method has obvious advantages. At the same time, the prediction model based on TCN can accurately predict the performance degradation of the rolling contact fatigue specimen with the root mean square error 0.0146 and the mean absolute error 0.0105, which has better performance and higher prediction accuracy than the prediction model based on the long short-term memory (LSTM) network and the gated recurrent unit (GRU). This method has general significance and may be extended to the performance degradation prediction of other mechanical equipment/parts.

A digital text abstract presents the essential information of an article, and we can find the trend and value of the research by analyzing it rigorously and digging up knowledge. Therefore, this study focuses on the abstracts of index journals in China and Taiwan from July 2010 to June 2020 (a total of 3,283 abstracts). Through the concepts of text mining and natural language processing (NLP), it constructs processes such as text retrieval, text segmentation and word cloud analysis, TF-IDF weight analysis, co-word analysis, network analysis, and trend analysis, and analyses a large amount of text data. The results show that the scope of research in China covers the fields of social sports and sports science, and research in Taiwan covers both natural and social sciences. The network diagram highlights the richness of sports-related research fields in the two regions, but research on sports philosophy is relatively rare. It is suggested that all disci-plines/departments should re-allocate the same resources, so as to show a balanced development trend and help expand a new chapter in the sports academic field.

Cereal crops, such as oats and barley, possess a number of valuable properties that meet the requirements for functional diet components. This review summarized the available information about bioactive compounds of oat and barley grain. The results of studying the structure and physicochemical properties of the cell wall polysaccharides of barley and oat are presented. The main components of the flavonoids formation pathway are shown and data, concerning anthocyanins biosynthesis in various barley tissues, are discussed. Moreover, we analyzed the available information about structural and regulatory genes of anthocyanin biosynthesis in Hordeum vulgare L. genome, including β-glucan biosynthesis genes in Avena sativa L species. However, there is not enough knowledge about genes responsible for biosynthesis of β-glucans and corresponding enzymes and plant polyphenols. The review also covers contemporary studies about collections of oat and barley genetic resources held by VIR. This review intended to provide information on the processes of biosynthesis of biologically active compounds in cereals that will promote further researches devoted to transcription factors controlling expression of structural genes and their role in other physiological processes in higher plants. Found achievements will allow breeders to create new highly productive varieties with the desirable properties.

The literature shows that both in laboratory and in industrial conditions, photocatalytic oxidation method copes quite well with the degradation of the most organic substances, including environmental toxins and molecular components of pathogenic microorganisms. However, the effective utilization of photocatalytic processes for environmental decontamination and disinfection require significant technological advancement both in the area of semiconductor material synthesis and its application. Here we focused on the presence and ‘photocatalytic capability‘ of photocatalysts among soil minerals, and their potential contribution to the environmental decontamination in vitro and in vivo. (The issue is sketched from the perspective of chemists and environmental scientist.) Reactions caused by sunlight on the soil surface are involved in its normal redox activity. It appears that some of them may take part in the soil decontamination. However, their importance for decontamination in vivo cannot be overstated due to diversity of soils on the Earth caused by the environmental conditions, such as climate, parent material, relief, vegetation etc. The solar-light induced reactions are just a part of extremely complicated processes dependent on a plethora of environmental determinates. Such multiplicity of affecting factors, which we tried to sketch from the perspective of chemists and environmental scientist, makes us rather sceptical about the effectiveness of the photocatalytic processes in vivo. On the other hand, there is a huge potential of the soils as the alternative source of useful photocatalytic materials of unique properties

Photovoltaic(PV) power generation is highly nonlinear and stochastic. Accurate prediction of PV power generation plays a crucial role in grid connection as well as the operation and scheduling of power plants. To predict the PV power combination model, this paper suggests a method based on Empirical Mode Decomposition (EMD), Ensemble Empirical Mode Decomposition (EEMD), Complete Ensemble Empirical Mode Decomposition with Adaptive Noise (CEEMDAN), Nonlinear Auto-Regressive Neural Networks with Exogenous Input (NARXNN), Long Short Term Memory (LSTM) Neural Network, and Light Gradient Boosting Machine (LightGBM) algorithms. To attempt to reduce the non-smoothness of PV power, the weather variable features with the greatest effect on PV power are first identified by correlation analysis. Following this, the PV power modal decomposition is split and reorganized into a new feature matrix. Finally， a NARX is used to obtain preliminary PV power components and residual vector features， and the PV power is predicted by combining three models of LightGBM， LSTM, and NARX and then the final prediction results are obtained by combining the PV power prediction results using error inverse method weighted optimization. The prediction results demonstrate that the model put forth in this paper outperforms those of other models and validate the model's validity by utilizing real measurement data from Andre Agassi College in the United States.

Plants are affected by soil environments to the same extent they affect soil functioning through interactions between environmental and genetic factors. Here, five plant species (broad bean, pea, cabbage, fennel, and olive) grown under controlled pot conditions were tested for their ability to differently stimulate the degradation of standard litter. Litter, soil C and N contents and soil microbial abundance were measured. The architecture and morphological traits of roots systems were also evaluated by using specific open-source software (SmartRoot). Soil chemical and microbiological characteristics were significantly influenced by the plant species. Variations in soil C/N dynamics were correlated with the diversity of root traits among species. Early-stage decomposition of the standard litter changed on the basis of the plant species. The results indicated that key soil processes are governed by interactions between plant roots, soil C and N, and the microbial metabolism that stimulate decomposition reactions. This, in turn, can have marked effects on soil chemical and microbiological fertility, both fundamental for sustaining crops, and can promote the development of new approaches for optimizing soil C and N cycling, managing nutrient transport, and sustaining and improving net primary production.

Diesel engines, as power equipment, are widely used in the fields of automobile industry, ship and power equipment. Due to wear or faulty adjustment, the valve train clearance abnormal fault is a typical failure of diesel engines, which may result in the performance degradation, even valve fracture and cylinder hit fault. However, the failure mechanism features mainly in time domain and angular domain, on which the current diagnosis methods based, are easily affected by working conditions or hard to extract accurate enough, as the diesel engine keeps running in transient and non-stationary process. This work arms at diagnosing this fault mainly based on frequency band features which would change when the valve clearance fault occurs. For the purpose of extracting a series of frequency band features adaptively，a decomposition technique based on improved variational mode decomposition is investigated in this work. As the connection between the features and the fault is fuzzy, the random forest algorithm is used to analyze the correspondence between features and faults. In addition, the feature dimension is reduced to improve the operation efficiency according to importance score. The experimental results under variable speed condition show that the method based on variational mode decomposition and random forest is capable to detect valve clearance fault effectively.

Arsenic, an element of environmental impact, can be incorporated into jarosite–type compounds and remain stabilised within the structure under a wide range of environmental conditions. In this study, a sample of ammonium–arsenic jarosite was synthesised by precipitation in sulphate medium at controlled pH of 1.2–1.8. The behaviour of arsenic during the thermal and chemical decomposition of jarosite was analysed; the degradation in alkaline medium of jarosite was also studied. According to the results, the synthesised jarosite is composed of joined rhombohedral crystals, forming tightly spherical shaped particles, 37–54 μm size. The ammonium jarosite produced possessed a high arsenic concentration; its calculated stoichiometry being (NH₄)Fe_2.45[(SO₄)_1.80(AsO₄)_0.20][(OH)_4.15(H₂0)_1.85]. It was found that arsenic is stabilised in the jarosite structure; upon heating, it remains in residual solids above 700°C, whilst in alkaline medium an incongruent dissolution takes place, with the arsenic retained in the solid phase along with iron. These solids, when exposed to high temperatures (1200°C), transform into a type of iron oxide known as hematite, so with arsenic it is retained an iron compound forming a stable compound which withstands high temperatures.

For the purpose of clean energy hydropower development, the construction of reservoirs has been continuously promoted in the Jinsha River basin for many years, and how the reservoirs affect the water and sediment process is a very necessary topic to study. This study is based on the gauged water and sediment data (span from the 1960’s to 2020) at Shigu, Panzhihua, and Xiangjiaba stations downstream located in the trunk channel of the river, and uses Mann-Kendall trend test method and double cumulative curve method to comprehensively judge the variation trends of runoff and suspended sediment load and reveal their credible mutation years. The linear regression method is used to reveal the variation characteristics of the relationship between water and sediment before and after the abrupt change years. The results show that the variations in runoff at Shigu and Panzhihua stations have significant and relatively obvious increasing trends, respectively, and that at Panzhihua station has a mutation year of 1985. The runoff at Xiangjiaba Station slightly increased but not significantly. The variation of suspended sediment load showed a temporal and spatial differentiation. The variation of sediment discharge at Shigu Station showed an increasing trend with a mutation year of 1997. For Panzhihua Station, it showed an increasing trend before 1998, but has significantly decreased since 1998. The fluctuation of sediment transport at Xiangjiaba Station was significant before 1998, but the trend is unclear. In the period of 1998−2020, it showed a significant decreasing trend, especially since 2013, when the mean annual suspended sediment load only accounted for 0.61% of its multi-year average. The variations of mean annual sediment concentration and sediment inflow coefficient at the hydrological stations is consistent with the variation trend of sediment transport. Before 2013, the correlation between water and sediment was strong, but thereafter it was extremely weak. The two sudden years of 1998 and 2013 are consistent with the year when large reservoirs were built in the river basin. The construction of large reservoirs and their large amount of sediment retention are the key reasons for the sudden changes in the water-sediment relationship and the sharp decrease in sediment transport in the downstream reach of the reservoir dam. The climate and underlying surface changes in the study area are not significant, and their impact on the water and sediment processes in the watershed is limited.

In the paper, we measure the digital financial inclusion index of 31 provinces in China from 2011 to 2020 based on three dimensions: coverage breadth, depth of use and digitalization degree. By means of weighted Dagum Gini coefficient and quantile standardization, we explored the degree of imbalance and insufficiency of the development of digital inclusive finance in China and four major regions and its structural causes. Using Kernel density estimation method and Markov chain analysis method, we further investigates the evolution trend of imbalance and insufficiency. The study finds that (1) the Digital Inclusive Financial Index in China and the four major regions rise significantly, with the COVID-19 epidemic reducing its growth rate. Of these, the eastern region has the highest development level. (2) The imbalance level of digital inclusive finance development obviously has reduced. The level of imbalance is highest within the eastern region, and the development gap between the eastern and western regions is the widest. The imbalance of overall development is mainly due to the regional imbalance. The imbalance of coverage breadth and depth of use is the main structural cause of unbalanced development in the four major regions. There is a trend of bipolarization or multipolarization in China and the other three major regions, with the exception of the central region. (3) The western region is the least developed. The development shortcoming of digital inclusive finance in China and the four major regions is the breadth of coverage. There are "Club Convergence" and "Matthew Effect" in the eastern, central and western regions.

Drought severity still remains a serious concern across sub-Saharan Africa (SSA) due to the destructive impact on multiple sectors of our society The interannual variability and trends in the changes of self-calibrated Palmer Drought Severity Index based on Penman–Monteith (scPDSIPM) and Thornthwaite (scPDSITH) methods for potential evapotranspiration (PET), precipitation (P) and normalized difference vegetation index (NDVI) anomalies, and sea surface temperature (SST) anomaly were investigated through statistical analysis of modelled and remote sensing data. It is shown that scPDSIPM and scPDSITH differed in the representation of drought characteristics over SSA. The scPDSI and remotely-sensed-based anomalies of P and NDVI showed wetting and drying trends over the period 1980-2012. The trend analysis showed increased drought events in the semi-arid and arid regions of SSA over the same period. A correlation analysis reveals a strong relationship between scPDSI variability and P, and NDVI anomalies for monsoon and pre-monsoon seasons. The correlation analysis of scPDSI variability with SST anomalies indicates significant positive and negative relationships, respectively. This study has demonstrated the applicability of multiple data sources for drought assessment and provides useful information for regional drought predictability and mitigation strategies.

This study investigates the trend in monthly and annual rainfall, minimum and maximum temperature (T_min and T_max) using the Mann–Kendall (MK) test and Sen’s slope (SS) method and evaluates the significance of their variability for maize, sorghum and millet yields in northern Togo employing multiple regression analysis. The historical data of Kara, Niamtougou, Mango and Dapaong weather stations from 1977 to 2012 were used. Four non-parametric methods—Alexandersson’s Standard Normal Homogeneity Test (SNHT), Buishand’s Range Test (BRT), Pettitt’s Test (PT) and Von Neumann’s Ratio Test (VNRT)—were applied to detect homogeneity in the data. For the data which were serially correlated, a modified version of the MK test (pre-whitening) was utilised. Results showed an increasing trend in the annual rainfall in all four locations. However, this trend was only significant at Dapaong (p < 0.1). There was an increasing trend in T_max at Kara, Mango and Niamtougou, unlike Dapaong where T_max revealed a significant decreasing trend (p < 0.01). Similarly, there was an increasing trend in T_min at Kara, Mango and Dapaong, unlike Niamtougou where T_min showed a non-significant decreasing trend (p > 0.05). Rainfall in Dapaong was found to have increased (7.79 mm/year) more than the other locations such as Kara (2.20 mm/year), Niamtougou (4.57 mm/year) and Mango (0.67 mm). T_max increased by 0.13, 0.13 and 0.32 °C per decade at Kara, Niamtougou and Mango, respectively, and decreased by 0.20 per decade in Dapaong. Likewise, T_min increased by 0.07, 0.20 and 0.02 °C per decade at Kara, Mango and Dapaong, respectively, and decreased by 0.01 °C per decade at Niamtougou. Results of multiple regression analysis revealed nonlinear yield responses to changes in rainfall and temperature. Rainfall and temperature variability affects rainfed cereal crops production, but the effects vary across crops. The temperature has a positive effect on maize yield in Kara, Niamtougou and Mango but a negative effect on sorghum in Niamtougou and millet in Dapaong, while rainfall has a negative effect on maize yield in Niamtougou and Dapaong and millet yield in Mango. In all locations, rainfall and temperature variability has a significant effect on the cereal crop yields. There is, therefore, a need to adopt some adaptation strategies for sustainable agricultural production in northern Togo.

In order for the body to function properly, it needs not only food, but also nutrients and non-nutritive bioactive compounds that have an immunomodulating effect. This applies not only to healthy people, but especially to people with accompanying chronic diseases, including type 2 diabetes. Unfortunately, the current food industry and the use of highly processed food promote nutritional deficiencies. Many studies confirm their occurrence in patients with type 2 diabetes. The article presents the influence of selected nutrients on the functioning of the immune system, which ensures homeostasis of the body, with particular emphasis on type 2 diabetes. The role of macroelements, microelements, vitamins and selected substances, such as omega-3 acids, coenzyme Q10 and alpha-lipoic acid. The minimum scope of tests that should be performed in patients to directly or indirectly determine the degree of malnutrition in this group of patients is presented.

Partial Information Decompositions (PIDs) aim to categorize how a set of source variables provide information about a target variable redundantly, uniquely, or synergetically. The original proposal for such an analysis used a lattice-based approach and gained significant attention. However, finding a suitable underlying decomposition measure is still an open research question, even at an arbitrary number of discrete random variables. This work proposes a solution to this case with a non-negative PID that satisfies an inclusion-exclusion relation for any f-information measure. The decomposition is constructed from a pointwise perspective of the target variable to take advantage of the equivalence between the Blackwell and zonogon order in this setting. The zonogons correspond to the Neyman-Pearson region for an indicator variable of one target state and f-information is the expected value of quantifying its boundary. We prove that the decomposition satisfies the axioms of the original decomposition framework and guarantees non-negative partial information results. We highlight that our decomposition behaves differently depending on the used information measure, which can be utilized for different applications. We additionally show how our proposal can be used to obtain a non-negative decomposition of Rényi-information at a transformed inclusion-exclusion relation, and for tracing partial information flows through Markov chains.

The research develops and validates new decomposition models for DNI estimations from Southern African data. The results demonstrated improved DNI estimation accuracy compared to the baseline models across all testing and validation datasets. These outcomes suggest that utilising a localised model can significantly enhance DNI estimations for Southern Africa and potentially for developing similar models in diverse geographic regions worldwide. Furthermore, clustered models highlighted the potential advantages of grouping data based on shared geographical and climatic attributes. This clustering approach could enhance decomposition model performance, particularly when local data is limited or data is available from multiple nearby stations. The Southern African decomposition model, which encompasses a wide spectrum of climatic regions and geographic locations, exhibited notable improvements over the baseline models despite occasional overestimation or underestimation. The overall metrics affirm the substantial advancement achieved with the Southern African model. This study focused on validating the model for hourly DNI in Southern Africa within a range of clearness index-intervals from 0.175 to 0.875. Implementing accurate decomposition models in developing countries can accelerate the adoption of renewable energy sources, diminishing reliance on coal and fossil fuels.

Due to nonlinear components in the charging piles of electric vehicles, harmonics and non-stationary signals in the electric vehicle charging load brings voltage and current distortion, seriously affecting the accuracy of the power-related calculation in non-sinusoidal environments. This paper proposed a new approach to calculate the active power and root mean square values from decomposed components using the adaptive chirp mode decomposition (ACMD) method on voltage and current. The advantage of the ACMD-based method is that it correctly provides the power-related quantities of harmonics or non-stationary components for the electric vehicle charging load. The performance of the proposed method was verified using synthetic signals and simulation tests. The experimental results presented better estimations for each quantity defined in IEEE Standard 1459-2010, compared with the discrete wavelet transform approach.

Highly reactive decomposition products of (deuterated) chloroform can deteriorate samples dissolved in this commonly used NMR solvent. For sensitive samples (such as peptides, unsaturated fatty acids, vitamins), this can lead to abnormal NMR spectra (e.g. signal shifts depending on pH, attenuation of signals over time due to chemical changes of analytes, new signals from reaction products). Such irreproducibly influenced spectra are especially problematic for non-targeted analysis methods. To prevent these artefacts, chlorine, phosgene and hydrochloric acid need to be eliminated from deuterated chloroform prior to its use. Since the common stabilization methods have proven insufficient for sensitive NMR samples, another purging method has been tested: Mitigation is easily and reliably achieved by washing the deuterated chloroform with concentrated Na2CO3-solution and subsequent desiccation with oven-dried Na2CO3.

In this paper, a two-stage stochastic programming modelling is proposed to design a multi-period, multistage, and single-commodity integrated forward/reverse logistics network design problem under uncertainty. The problem involves both strategic and tactical decision levels. The first stage deals with strategic decisions, which are the number, capacity, and location of forward and reverse facilities. At the second stage tactical decisions such as base stock level as an inventory policy is determined. The generic introduced model consists of suppliers, manufactures, and distribution centers in forward logistic and collection centers, remanufactures, redistribution, and disposal centers in reverse logistic. The strength of proposed model is its applicability to various industries. The problem is formulated as a mixed-integer linear programming model and is solved by using Benders’ Decomposition (BD) approach. In order to accelerate the Benders’ decomposition, a number of valid inequalities are added to the master problem. The proposed accelerated BD is evaluated through small-, medium-, and large-sized test problems. Numerical results reveal that proposed solution algorithm increases convergence of lower bound and upper bound of BD and is able to reach an acceptable optimality gap in a convenient CPU time.

Abstract: This paper presents a comprehensive analysis of links between satellite-measured vegetation vigor and climate variables in Armenian mountain grassland ecosystems in years 1984–2018. NDVI is derived from MODIS and Landsat data, temperature and precipitation data are from meteorological stations. Two study sites were selected, representing arid and semi-arid grassland vegetation types, respectively. Various trend estimators including Mann-Kendall (MK) and derivatives were combined for vegetation change analysis at different time scales. Results suggest that temperature and precipitation had negative and positive impacts on vegetation growth, respectively, in both areas. NDVI-to-precipitation correlation was significant but with an apparent time-lag effect that was further investigated. No significant general changes were observed in vegetation along the observed period. Further comparisons between results from corrected and uncorrected data led us to conclude that MODIS and Landsat data with BRDF, topographic and atmospheric corrections applied are best suited for analyzing relationships between NDVI and climatic factors for the 2000-2018 period in grassland at a very local scale, but in the absence of correction tools and information, uncorrected data can still provide meaningful results. Future refinements will include removal of anthropogenic impact, and deeper investigation of time-lag effects of climatic factors on vegetation dynamics.

Through the arrow decomposition of the Mueller matrix, respective sets of sixteen independent polarimetric images of biological tissues are obtained for enpolarizing, retarding and depolariz-ing descriptors. In addition to the mean intensity coefficient and the three indices of polarimetric purity, the absolute values and Poincaré orientations of diattenuation, polarizance, entrance re-tardance and exit retardance vectors are considered. In this work we use for the first time this set of polarimetric observables for the visualization of biological structures, both of animal and vege-tal origin. Results show images with enhanced visualization derived from the spatial variation of such significant polarimetric properties. The experimental results are discussed, showing the suit-ability of such set of observables for applications in biophotonics imaging, providing not only ex-cellent visualization of biological tissues, but also showing structures not visible in non-polarimetric images.

Iron oxide nanoparticles are widely used as contrast agent for MRI and may be used as therapeutic agent by magnetic hyperthermia if they display a high magnetic anisotropy. Considering the effect of the nanoparticles shape on anisotropy, the reproducible shape control of nanoparticles is currently a challenge of synthesis methods. By investigating reaction parameters which are the iron precursor structure, the water content and the amount of the surfactant, sodium oleate, reported to trigger the cubic shape, iron oxide nanoparticles with different shape and composition were observed to form. In particular, iron oxide nanoplates have been thus synthesized. The effect of the surfactant coming from precursor was taking into account by using in house iron stearates bearing either two or three stearate chains and the negative effect of water on shape was confirmed by considering these precursors after their dehydration. Nanocubes with straight faces and a FeO@Fe3-xO4 composition were obtained only with dehydrated precursors and 50% of sodium oleate in the oleic acid and sodium oleate surfactant mixtures. When iron stearates with three chains led mainly to nanocubes in presence of soduim oleate, Iron stearates with two chains led to the formation of nanoplates with 80% of sodium oleate. The original flat shape of the plates was confirmed with 3D TEM tomography. The investigation of the synthesis mechanisms confirmed the major role of deprotonated carboxylic acid and of the heating rate to drive the cubic shape of nanoparticles and showed that the nanoplate formation would depend mainly on the nucleation step and possibly on the presence of a given ratio of oleic acid and deprotonated carboxylic acid.

Highly photoluminescent C-Dots are prepared by hydrothermal reaction of citric acid and piperazine as dual reason in both hydrolysis and surface passivation agent along with the N-doping agent. The resulting C-Dots without external passivation showed PL enhancement by electron transfer from C-Dots-donor to piperazine-acceptor with the maximum emission yields of more than 84%. After mixing the prepared C-Dots with the mixture of EtOH and acetone (1:1 vol %), a novel washing process was performed by centrifugation to remove the precursors and by-products. The resulting C-Dots showed much better stability than dialysis. For evaluating the possible application of the C-Dots as a fluorescent biological probe which possess the wide dosing window and multicolor properties. The C-Dots were localized in perinuclear vacuole-like structures with granular pattern in cytoplasm sparing the nucleus. No signs of any morphological deterioration like nuclear shrinkage were observed.

Densimetric Froude (Fr) is the minimum velocity required to prevent sediment deposition in pipes. Prediction of Fr is of utmost importance in numerous applications in civil engineering. In this paper through using a new hybrid method. Genetic Algorithm (GA) is used for optimum selection of membership functions of Adaptive Neuro-Fuzzy Inference System (ANFIS), and Singular Value Decomposition (SVD) method is used to compute the linear parameters of ANFIS’s results section (ANFIS-GA/SVD). Also, two different target functions are known as training error (TE) and prediction error (PE) by Pareto curve, the trade-off between these functions is selected as the optimal modeling point. First, different models will be presented using the parameters affecting Fr prediction, classifying them in different groups; then the Fr parameter will be predicted for all the different models through utilizing three different sets of data and the ANFIS-GA/SVD technique. The results of the models indicate that the best Fr prediction is obtained when independent parameters such as volumetric sediment concentration (CV), ratio of median diameter of particle size to pipe diameter (d/D), ratio of median diameter of particle size to hydraulic radius (d/R) and overall friction factor of sediment (λs) use as input variables in prediction of Fr. A sensitivity analysis is also conducted for the purpose of examining the effect of each of the dimensionless parameters on Fr prediction accuracy. Comparing the results of the suggested models with the existing regression-based equations shows that ANFIS-GA/SVD (R²=0.986, MAPE=4.397, RMSE=0.206, SI=0.053, ρ=0.026, BIAS=-0.025) is more accurate than the rest of the models.

The vibration signal of heavy gearbox presents non-stationary and nonlinear characteristics, which increases the difficulty to extract the fault feature. When the gear has a subtle fault, it may cause a perceptible change of local fluctuation rather than the large scale fluctuation. Therefore, the feature parameters extracted from local fluctuation can effectively improve the recognition performance of the gear fault. In this paper, a novel signal processing method based on variational mode decomposition (VMD) and detrended fluctuation analysis (DFA) is proposed to identify the gear fault of heavy gearbox. Firstly, the raw vibration signal is decomposed several mode components by VMD, which is an adaptive and non-recursive signal decomposition method. Next, the sensitive mode component is selected by a maximal indicator, which is composed of kurtosis and correlation coefficient of relative higher frequency mode components corresponding to local fluctuation of raw vibration signal. Finally, the characteristics of the double-scales feature parameters of selected sensitive mode are extracted by DFA. In addition, the position of turning point of double scales is estimated by sliding windowing algorithm. The proposed method is evaluated through its application to gear fault classification using vibration signal. The results demonstrates that the recognization rate of gear faults condition have marked improvement by proposed method than the DFA of Small Time Scale (STS-DFA) method.

Because of ambiguous and widely debated observations concerning incidence trend and management of TC, we performed this analysis. We drew attention to some events, such as “cancer screening activity,” introduction of noninvasive follicular neoplasm with papillary-like nuclear features (NIFTP) to TC types, possibility of papillary thyroid microcarcinoma (PTMC) active surveillance (AS), occurrence of personalized medicine in TC management and finally COVID-19 pandemic time. Because of the opinion that all changes have been made mostly by PTC, we compared it to the rest of types of TC in terms of incidence, clinical and pathological characteristics and treatment. The prevalence of TC significantly increased from 5.15% in 2008 to 13.84% in 2015 and then significantly decreased to 1.33% in 2022 when the pandemic lasted (p<0.0001). A similar trend was observed for PTC, when the incidence significantly increased to 13.99% in 2015 and then decreased to 1.38% in 2022 (p<0.0001). At that time, the NIFTP category was introduced, and observation of PTMC began. The prevalence of FTC and MTC also increased until 2015 and then decreased. Significant differences in age, types of surgery, necessity of reoperation, pTNM, between PTCs and other types of TCs were observed. The average age was significantly lower in PTC patients than in patients with the remaining types of TC (p<0.0001). Four milestones, including NIFTP introduction, the possibility of PTMC AS, personalized cancer medicine and the COVID-19 pandemic, may have influenced the general statistics of TC.