The rapid development of the Industrial Internet of Things (IIoT) has brought enormous opportunities to the industrial environment but has also posed significant challenges to network security, especially the physical layer security challenges,which is crucial for the reliable transmission of messages interconnected devices and sensors. Focus on the enhancing the physical layer security in the IIoT communication, this paper proposed a mechanism of Spatial Secrecy Outage Probability (SSOP) to ensure the secure transmission of data. The SSOP algorithm assumes that the location of legitimate device is known, while eavesdropper on the random distribution of device locations, forming the SSOP model related to device locations from the perspective of insecure regions (ISR) and secure regions (SR), and deduce the closed-form expression for its upper bound. Subsequently under the constraint of SSOP conditions, establish an optimization model with the objective of system throughput maximization based on Spatial Secrecy Outage Probability(SRM-SSOP). By optimizing the transmission rate of legitimate channels or controlling the transmission power, the maximization of system throughput can be achieved, thus reducing the consumption of communication resources. Through sophisticated modeling and simulation in the MATLAB, we verified the accuracy of the definition and derived upper bound of SSOP. The experimental results also show that SSOP algorithm gradually converges to a specific value as the number of antenna elements increases. In addition, we observed that when the receiver device is aligned with the normal direction of the transmit antenna array, the SSOP reaches a minimum value. These performance are crucial for understanding and optimizing the security performance of IIoT communication systems.

The purpose of the study is to establish compliance of the design of the modernized car with the requirements for safe operation. An option has been proposed for upgrading a passenger wagon to a Mobile Diagnostic Complex for transporting a combined vehicle equipped with appropriate flaw detection equipment intended for rail diagnostics. The authors have established the most optimal option for locating the diagnostic vehicle on board the Mobile Diagnostic Complex (MDC) wagon, taking into account the additional load from the vehicle. To achieve this goal, the article developed a three-dimensional model of the supporting structure of the wagon body, proposed a methodology and presented the results of a study of the stress-strain state of the wagon body, taking into account the additional weight of the wagon. The article develops a methodology for studying the natural frequencies of vibrations of the wagon body and develops a three-dimensional model of the wagon for calculating dynamic indicators in the Universal Mechanism software package. Taking into account the previously carried out strength calculations, as well as in order to maintain the factory life cycle indicators of the supporting structure of the wagon body, it is recommended to use the model in the first version.

The emergence of prosumers, who actively participate in designing and producing goods, has generated interest in domestically manufactured products. Factors such as innovation, design methods, component reuse, prototyping, and digital fabrication empower prosumer designers to realize their ideas and enhance products to meet their specific design requirements. This article presents a case that combines bioinspired design methods with prosumer characteristics from the perspective of a designer who uses biological research results acting as a prosumer. By analyzing prosumer needs, bioinspired design, and domestic fabrication requirements, designers define the methods that best suit their possibilities. As a result of using biological information, the geometry of Samara seeds, propeller sizing, wind tunnel tests, and subsequent improvements, the custom design of a bioinspired microgenerator has been refined to the final design of a bicycle flashlight. The aim is to popularize a working approach that facilitates the interaction of design methods and reinforces domestic manufacturing processes. Implementing bioinspired design methods within the prosumer context offers a methodological alternative to transform the current economic model, promoting systemic sustainability and the development of proprietary technologies.

In the last decades, the impacts of urbanization on the hydrological cycle have led to an increase in the frequency and magnitude of urban flooding events, also amplified by the effects of climate change. Sustainable Drainage Systems (SuDS) provide a revolutionary change in this field, improving the sustainability and resilience of cities. This research explores the integration of different SuDS with the aim of significantly reducing both flow volume and celerity of floods in a residual urban catchment area of metropolitan city of Querétaro (Mèxico), where extreme rainfall frequently occurs. This catchment is a representative suburb of urban pressure and environmental degradation problems. Currently, managing storm water under climate uncertainty through a multi-disciplinary approach is a major concern in this urban area. A 1D-2D coupling model of shallow water equations, finite volume method, unstructured meshing method, and hybrid parallel computing application defined the optimal configuration of SuDS at catchment scale to reduce the flood vulnerability in Querétaro. Specifically, in this paper we explore the management issues of the proposed SuDS configuration that acts as a water resource system with multiple purposes. A generic simulation model called MODSIM was applied to simulate the designed urban drainage system under a balanced IPCC future climate scenario in terms of reliability, resilience and vulnerability against water scarcity.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

A proposed low-temperature forging method aims to enhance stainless steel bearings by creating a martensitic subsurface layer, significantly boosting bearing fatigue life due to increased surface hardness. This technique induces beneficial residual stresses, particularly in axial bearings, streamlining their construction and improving machine elements. Challenges persist, especially with radial bearings, but simplicity in axial bearing forging promotes compact, resource-efficient facility construction. Future research will focus on applying this technique to axial bearing washers, potentially replicating success in other bearing components. Despite the energy ex-penditure for cooling during forging, the substantial increase in bearing fatigue life offsets this, enhancing overall longevity and reliability of critical machine components. Integration of this forging technique into bearing fabrication appears seamless, offering a promising trade-off be-tween energy use and enhanced performance.

Tremor is a prevalent neurological disorder characterized by involuntary shaking or trembling of body parts. This condition impairs fine motor skills and hand coordination to varying degrees and can even affect overall body mobility. As a result, tremors severely disrupt the daily lives and work of those affected, significantly limiting their physical activity space. This study developed an innovative Spatial Augmented Reality (SAR) system aimed at assisting individuals with tremor disorders to overcome their physical limitations and expand their range of activities. The system integrates eye-tracking and Internet of Things (IoT) technologies, enabling users to smoothly control objects in the real world through eye movements. It employs a virtual stabilization algorithm for stable interaction with objects in the real environment. The study comprehensively evaluated the system's performance through three experiments: 1) assessing the effectiveness of the virtual stabilization algorithm in enhancing the system's ability to assist individuals with tremors in stable and efficient interaction with remote objects; 2) evaluating the system's fluidity and stability in performing complex interactive tasks; 3) investigating the precision and efficiency of the system in remote interactions within complex physical environments. The results demonstrate that the system significantly improves the stability and efficiency of interactions between individuals with tremor and remote objects, reduces operational errors, and enhances the accuracy and communication efficiency of interactions.

The multiphase motors due to their reliability find new areas of application in the industry and transportation. Developing of any system with multiphase motors at first requires elaborate model of the system, define control mode and controllers. The model of control system for the six-phase drive is based on its conventional d-q mathematical model and indirect field-oriented control. Simulink model of six-phase drive with indirect field-oriented control and simulated with two types PID and PID fuzzy controllers. The simulation results, reflecting step response and provided speed reference law as well as load application at constant speed, are presented and analyzed. Fuzzy controller with 49 rules is considered and applied. Six-phase electric drive with field-oriented control at well-tuned PID controller has good step response specifications: settling time 0.13 s at starting without load, step response has no overshoot, small about 1 % short time decrease of speed at load of 5 Nm application. The system employing PID fuzzy controller shows slightly better results in response to torque application: the decrease in speed 1 % is eliminated in shorter time. Simulation results indicate the robustness of both systems with six-phase drive to disturbance and provide high quality transient specifications at determined reference speed.

The development of ballistic protection vests (BPVs) has become increasingly significant, particularly in the design of soft panels, which are critical to the overall size and configuration of these vests. Despite their importance, a standardized design process for soft panels is lacking in the literature. This research addresses this gap by creating soft panels tailored to the body types of regional soldiers while adhering to relevant standards. We propose a comprehensive design algorithm and evaluate the applicability of the National Institute of Justice (NIJ) standard 0101.06 test templates for configuring these panels. This study aims to design soft ballistic panels for BPVs that cater to the body type requirements of regional soldiers and comply with NIJ 0101.06 standards. We have developed an algorithm for designing soft panels and analyzed the feasibility of using NIJ test templates for their configuration. The research encompasses a detailed literature review, analysis of existing BPV soft panels, and comparison with NIJ test templates. The panels were designed and scaled using computer-aided design (CAD) systems and evaluated through by physical fitting on mannequins and virtual fitting using the Clo3D program. Our findings indicate that the NIJ standard test templates are only partially applicable to the design of soft panels. The developed methodology includes an algorithm and size specifications tailored to regional covers. A coefficient (K) was identified to calculate the soft panel surface area prior to design, thereby saving time and resources.

Nowadays, microfluidics has become an anarchist interdisciplinary topic with considerable attention in a wide range of biotechnology applications. In this research work, numerical investigation of microfluidic micro-mixer is carried out using hybrid actuation approach with different micropillar shapes and gaps. For this purpose, COMSOL Multiphysics is used with three different physics such as thermoviscous acoustic to solve acoustic governing equations, laminar physics is used to solve fluid flow governing equations and diluted transport species is used to solve mixing governing equations. The simulations were carried out with flow velocity of 200 µm/s at both inlets with an oscillation frequency of 15kHz. The outcomes were in the form of acoustic characteristics such as acoustic pressure, acoustic velocity, acoustic streaming and mixing index. The results revealed that the inclusion of micropillars enhanced the mixing performance and strength of acoustic field resulting in improvement of mixing performance compared to the case without micropillars. In addition, it was also investigated that blade shape micropillars with 0.150 mm gaps deliver best results compared to the other cases with maximum and minimum values of the mixing index 0.95 and 0.72 respectively. The obtained results can be extremely helpful for design and modifications of hybrid microfluidics micro-mixer.

Being able to express broad families of equivariant or invariant attributed graph functions is a popular measuring stick of whether graph neural networks should be employed in practical applications. However, it is equally important to learn deep local minima of losses (i.e., with much smaller loss values than other minima), even when architectures cannot express global minima. In this work we introduce the architectural property of attracting GNN optimization trajectories to local minima as a means of achieving smaller losses. We take first steps in satisfying this property for losses defined over attributed undirected unweighted graphs with a novel architecture, called Universal Local Attractor (ULA). The latter refines each dimension of end-to-end trained node feature embeddings based on graph structure to track the optimization trajectories of losses satisfying some mild conditions. The refined dimensions are then linearly pooled to create predictions. We experiment on 10 tasks, from node classification to clique detection, on which ULA is comparable with or significantly outperforms popular alternatives of similar or greater theoretical expressive power.

The Energy Performance of Buildings Directive 2010 calls for the Nearly Zero Energy Standard for new buildings from 2021 onwards: Buildings using “almost no energy” are powered by renewable sources or energy produced by the building itself. For residential buildings, this ambitious new standard has already been reached. But for other building types this goal is still far away. The potential of these buildings to meet a Nearly Zero Energy Standard was investigated by analyzing ten case studies representing non-residential buildings with different uses. The analysis shows that the primary characteristics common to critical building types are a dense building context with a very high degree of technical installation (such as hospital, research and laboratory buildings). The large primary energy demand of these types of buildings cannot be compensated by building and property-related energy generation including off-site renewables. If the future Nearly Zero Energy Standard were to be defined with lower requirements because of this, the state related properties of Bavaria suggest that the real potential energy savings available in at least 85% of all new buildings would be insufficiently exploited. Therefore, it would be useful to instead individualize the legal energy verification process for new buildings to distinguish critical building types such as laboratories and hospitals.

Energy harvesting is an emerging topic recently. This harvested energy is used to operate wireless sensors for different industrial monitoring and automation. To maximize the harvested energy in spinning systems, the harvester should vibrate at resonance for different spinning frequencies which can be achieved by active fitting. In this research, a novel methodology was developed by actively customizing the length of vibrating element beam to manipulate its natural frequency according to the spinning frequency. Different models were investigated numerically and experimentally to verify the proposed methodology. COMSOL Multiphysics software V5.1 was used to develop the numerical model, then and tip deformation and voltage difference results were benchmarked. The numerical model was verified experimentally by attaching a piezoelectric MIDE PPA 1021 which its vibrating length was varied by changing the supporting length from 0 mm to 12 mm to a spinning object having variable frequency from 0-200 Hz. It is found that the MIDE PPA 1021 beam vibrated at its resonance throughout the specified spinning frequencies. The proposed harvester can be applied in battery-free sensors being used in automotives, wind-mills blades, and rotating machinery.

Confronting the dual challenges of rapid urbanization and climate change, although extensive research has investigated the influencing factors and practical strategies of urban carbon emissions and urban vibrancy, respectively, the unclear mutual nexus between them and the development strategy of collaborative optimization requires further in-depth analysis. This study explores the delicate balance between urban vibrancy and low-carbon sustainability within the confines of Beijing’s Fifth Ring Road. By integrating OpenStreetMap, land use, population, and building carbon emission data, we have developed a reproducible method to estimate total carbon emission and emission intensity per capita. Furthermore, we have introduced vibrancy index data to distinguish the vibrancy evaluation of residential and non-residential land and applied cross-combinational classification technology to dissect the spatial correlation between urban carbon emissions and urban vibrancy. The results reveal that the four combination typologies show more significant differences and regularity in residential land. Based on the discovery of spatial correlation, this study puts forward corresponding development strategy suggestions for each typology based on geographical location and the requirements of urban development policies of these four combination typologies. In conclusion, our study highlights the importance of integrating carbon emissions and urban vibrancy comprehensively in sustainable urban planning and proposes that various land use combinations need targeted development strategies to achieve this goal, which need to consider population, energy, service facilities, and other diverse aspects.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

The assessment of existing bridges constitutes a serious challenge for the researchers since their safety evaluation is a complex task due to several sources of uncertainty affecting the parameters identified in the knowledge process. In particular, a high level of uncertainties may arise in the case of prestressing systems requiring special investigation strategies and experimental technologies. The paper aims to investigate how the knowledge uncertainties influence the safety assessment of existing post-tensioned bridges. The semi-probabilistic approach is used, and uncertainties related to the knowledge process are described considering the number of tests, the confidence level assumed for the estimation of the problem parameters, and the measurement errors of in-situ tests. Results concerning a typical post-tensioned bridge are reported and the variability of the outcomes is discussed and compared with a reference case of “perfect knowledge”. The main results of the study confirm the general robustness of the semi-probabilistic Eurocodes safety format and provide an overview of dispersion due to different choices about the number of tests and confidence level. The measurement errors may lead to significant under-estimation of the computed structural capacity with respect to the reference one.

Autonomous navigation in dynamic environments poses a significant challenge in the field of ro-botics with the primary goals of ensuring both smooth and safe movement. This study introduces control strategy based on an Adaptive Neuro-Fuzzy Inference System (ANFIS) to enhance au-tonomous robot navigation in dynamic environments, emphasizing on collision-free path plan-ning. This strategy employs, a path planning technique to develop a trajectory that allows the ro-bot to navigate smoothly while avoiding collisions with both static and dynamic obstacles. The developed control system incorporates four ANFIS controllers: two are tasked with guiding the robot toward its end point, and the other two are activated for obstacle avoidance. The experi-mental setup conducted in CoppeliaSim involves a mobile robot equipped with ultrasonic sensors navigating in an environment with static and dynamic obstacles. Simulation experiments are conducted to demonstrate the model's capability in ensuring collision-free navigation, employing a path planning algorithm to ascertain the shortest route to the target destination. The simulation results highlight the superiority of the ANFIS-based approach over conventional methods, partic-ularly in terms of computational efficiency and navigational smoothness.

Developing and utilising of underground space is an vital direction for urban growth. Underground commercial streets, as a significant component of underground space accommodating extensive human social activities, and consequently necessitate the creation of human-scale spaces. In the evolution of urban design development towards greater refinement, applying architectural theories and excessively subjective designs has resulted in a deficiency of human-centered design and a disordered spatial environment. This study merges environmental psychology and architectural theory to determine the appropriate length of spatial scale. Two experiments focusing on spatial perception evaluation were conducted using a virtual experimental platform that featured varying dimensions of spatial scale combinations. These quantified combinations were correlated with perception evaluation, and regression analysis was employed to identify appropriate scale ranges, which were superimposed on the range of length selection. Finally, the optimal length and scale combination for underground commercial street spaces were established, providing a reference for the human-centered design of these environments.

One of the primary causes of the mechanical seal failure is rotor vibration. Traditional dynamic seal models often would not be able to fully explaining the failure mechanisms. The seal dynamic models proposed in this paper, including those developed by the authors, prove valuable in predicting seal dynamics during operation in specific turbomachinery and in explaining the causes of seal failure. The single-mass dynamic model is suitable for analyzing contact mechanical seal and simple design dry gas seals dynamics. The two-mass dynamic model is used for investigating operational dynamics processes in classical dry gas seals under complex loading conditions. The three-mass dynamic model is used to study various complex mechanical seal types. This model is able to determine the normal operating condition range and to explain leakage mechanisms in the presence of excessive rotor vibrations.

The objective of this study is to determine the relationship between body condition score (BCS) and body carcass fat (BCF) of ewes at two key stages of the production cycle. Data were collected from 88 Coopworth ewes including BCS measurements manually evaluated by the farm manager, BCF measurements determined by computerized tomography (CT) and body parameter measurements automatically determined by an image processing application. Artificial neural network (ANN) statistical analysis method was used to develop a relationship between the body parameters and the BCF with an r2=0.96 and RMSE=1.01 using all top and side variables.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

The acoustic environment in learning spaces significantly influences learning effectiveness and occupant well-being. Recent studies have shown that a series of architectural factors within physical learning environments can impact students' educational experiences. This research delves into the relationship between architectural characteristics and the perceived acoustic environment among 467 primary students in 19 learning spaces across 9 schools in Chile. The survey comprises a student questionnaire, a checklist evaluating space characteristics, and acoustic measurements of indoor noise levels during occupied conditions. Examined topics include Indoor Environmental Quality (IEQ) comfort perception, noise annoyance, hearing ability, and acoustic preference. Architectural characteristics considered encompass flexible and acoustic space design parameters. The results indicated that noise discomfort was a common issue, especially in traditional learning spaces without acoustic treatment. The type of learning space (traditional or flexible settings) has a greater impact on acoustic perception particularly concerning noise discomfort and acoustic preference. However, poorly acoustic spaces lacking absorbing materials or exhibiting lower spatial density (m2 per student) contribute to increased indoor noise levels affecting noise annoyance caused by children's talking inside. The study emphasizes the importance of considering both architectural design and acoustic conditioning for optimizing the acoustic experience in educational spaces.

A challenge in building large-scale superconducting quantum processors is the precise control and manipulation of the qubit state. However, the crosstalk between the microwave control lines impedes the parallel execution of high-fidelity digital and analog quantum operations. Here, we propose and demonstrate a universal compensation protocol for calibrating the microwave signal crosstalk. We also introduce amplified error sequences to optimize the accuracy. Furthermore, we show a definitive improvement in parallel gate operations with crosstalk cancellation, demonstrating the technique's effectiveness. This work paves the way for superconducting hardware that features automated calibration of microwave crosstalk, leading to enhanced fidelities in multiqubit circuits.

In order to quickly develop a multi ship collaborative collision avoidance plan in multi ship encounter scenarios, a multi ship collision avoidance decision model is proposed in accordance with the requirements of the International Maritime Collision Avoidance Regulations, taking into account the collision avoidance operations in multi ship encounter scenarios. Firstly, the collision risk between ships is determined by the closest encounter distance (DCPA) and closest encounter time (TCPA). Secondly, a decision objective function is established based on rules, degree of ship deviation, and ship risk. Finally, the prediction mechanism is used to calculate the minimum value of the objective function and complete the collision avoidance decision. The simulation results show that in the scenario of multiple ship encounters, the collision avoidance model can achieve safe collision avoidance with a smaller steering frequency and a shorter col-lision avoidance time. The proposed multi ship collision avoidance model can provide reference for collision avoidance decision-making in multi ship encounter scenarios, which helps to im-prove the collision avoidance efficiency in multi ship collision avoidance

Firefighters Protective Clothing consist of several layers of different properties and functions. The layers create barriers against dangerous outer factor. However, they are also barriers to transport of sweat produced by human organism. It causes that very often sweat in the form of vapor is not transferred effectively from the human organism through the FPC to environment. This leads to sweat condensation on the skin of the FPC user causing his discomfort. In order to ensure as good as possible physiological comfort of firefighter while firefighting and other rescue actions it is necessary to take into consideration the transport of condensed sweat in the multilayer textile set creating the FPC. In the presented work four variants of multilayer textile sets for the FPC have been tested in the aspect of liquid moisture transport. Measurement was performed by means of the Moisture Management Tester (MMT290) – innovative instrument manufactured by the SDL Atlas. Obtained results showed that the transfer of sweat in liquid form occurs only in the inner, next to skin layer of the multilayer sets for the FPC.

This paper investigates the effects of various process parameters, specifically the substrate temperature, on weld track geometry in Directed Energy Deposition (DED) processes. A specialized experimental setup integrated within a DED machine facilitates controlled thermal conditioning of sample sheets. Through Design of Experiments (DoE) methods, individual weld marks are generated and analysed to assess geometric characteristics. Regression models are constructed to predict machine parameters for desired weld geometry at different substrate temperatures. Validation experiments confirm the accuracy and reliability of the regression models. Results show a consistent trend towards target geometric features across a broad range of substrate temperatures. Despite deviations in measured values, successful fabrication is achieved, demonstrating robust bonding between weld and substrate. Contact angle predictions exhibit precision within a partial temperature range for proper deposition. The developed model offers insights for optimizing DED process parameters to achieve desired weld characteristics, advancing the capabilities and reliability of additive manufacturing technology. Future work aims to refine the regression model and explore additional mathematical relationships for enhanced accuracy. An implication of this work is the potential to vary the local mechanical properties of parts by controlling the temperature profile while maintaining consistent geometric characteristics. By manipulating the substrate temperature, it may be possible to tailor the microstructure and mechanical properties of fabricated components in the future to meet specific requirements in different regions of the part.

Smartwatches are one of the most relevant fitness trends of the past two decades, and they collect increasing amounts of health and movement data. The accuracy of these data may be questionable and requires further investigation. Therefore, the aim of the present study is to validate smartwatches for use in triathlon training. Ten different smartwatches were tested for accuracy in measuring heart rate, distance (via global navigation satellite systems, GNSS), swim stroke rates and the number of swim laps in a 50 m Olympic-size pool. The optical heart rate measurement function of each smartwatch was compared to that of a chest strap. Thirty participants (15 females, 15 males) ran five 3-minute intervals on a motorised treadmill to evaluate the accuracy of the heart rate measurements. Moreover, for each smartwatch, running und cycling distance tracking was tested over six runs of 4,000 m on a 400 m tartan stadium track, six hilly outdoor runs over 3.4 km, and four repetitions of a 36.8 km road bike course, respectively. Three swimming protocols ranging from 200 m to 400 m were performed in triplicate in a 50 m Olympic-size pool, evaluating tracked distance and detected number of strokes. The mean absolute percentage errors (MAPEs) for the average heart rate measurements varied between 3.1% and 8.3%, with the coefficient of determination ranging from 0.22 to 0.79. MAPE results ranged from 0.8% to 12.1% for the 4,000 m run on the 400 m track, from 0.2% to 7.5% for the 3.4 km outdoor run, and from 0.0% to 4.2% for the 36.8 km bike ride. For the swimming tests, in contrast, the deviations from the true distance varied greatly, starting at a 0.0% MAPE for the 400 m freestyle and reaching 91.7% for the 200 m medley with style changes every 25 m. In summary, for some of the smartwatches, the measurement results deviated substantially from the true values. Measurements taken while road cycling over longer distances with only a few curves were in relative terms more accurate than for outdoor runs and even more accurate than for the 400 m track. In the swimming exercises, the accuracy of the measured distances was severely deteriorated by the medley changes among the majority of the smartwatches. Altogether, the results of this study should help in assessing the accuracy and thus suitability of smartwatches for general triathlon training.

Cities are complex systems requiring urban design models that balance order and disorder. Collective creativity initiatives engage citizens in these processes, empowering bottom-up approaches that prioritize people and social well-being within urban development. This paper investigates an 'Urban Laboratory' as a case study, examining the potential of collective creativity to address urban complexity. The successful and ongoing project 'El Campo de Cebada' in Madrid, Spain, demonstrates how a community transformed a vacant lot into a vibrant social hub. The phases of this study include case selection, data collection, data analysis, and presentation of the results. This study identifies key enabling factors, including agents, management, social dynamics, infrastructure, and actions. These insights offer a methodological framework for designing future collaborative, resilient, and inclusive urban spaces, addressing the complex needs of communities within our cities.

As the fast growth of information technology (IT), the safety of image transmission and the storing of images are increasingly concerned. Traditional image encryption algorithms have certain limitations in transmission and security, so there is an urgent need for a secure and reliable image encryption algorithm. A universal compression sensing (CS) image encryption (IE) algorithm based on DNA-triploid mutation (DTM) is presented in this paper. Firstly, by using CS algorithm an image is compressed while obtaining a range of chaotic sequences by iteration of chaotic map. Then DNA sequences are generated by encoding the image, and based on the DTM, new mutant DNA sequences are generated according to specific rules. Next, the chaotic sequences are operated at the DNA level to do confusion and diffusion operations on the image to ensure the security of the data. At last, DNA decoding is carried out to obtain the compressed-encrypted image. Both simulation experiments and performance tests fully show that a high level of security and reliability of the proposed algorithm in protecting image privacy is achieved.

Researchers have explored primary colour-geometric shape associations since Kandinsky's correspondence theory. However, there is a gap in the literature regarding interior colour applications on surface shapes. To address this gap, an online study was employed to gather data with one hundred participants who were asked to choose their preferred colours for shapes on bedroom walls with follow-up questions on the colour-shape semantic associations, their preference of colours and shapes on bedroom walls independently in addition to their favourite colour, their favourite shape, and colour-shape pairs without interior context. The results revealed that colour-shape preferences in interiors differ from those found in psychology studies, other colour applications on bedroom walls, and other preferences, indicating that colour preference is context-dependent. Interestingly, the most popular colour for surface shapes on bedroom walls is purple, followed by brown and blue. The study contributes to the existing literature by providing colour charts for bedroom applications for professionals in the industry, their clients/users, and future studies.

Environmental estrogen pollution and estrogen effects on the female reproduction system are well-recognized scientifically. Among the estrogens, 17 β-estradiol is a priority in environmental estrogen pollution, and it is also a major contributor to estrogen which regulates the female reproduction system. 17 β-estradiol is carcinogen and has a tumor promotion effect relating to breast cancer, lung cancer and others. It also affects the psychological well-being such as depression, fatigue and others. Thus, a simple method of detection of 17 β-estradiol will be important for both environmental estrogen pollution and women’s health care. This study demonstrates a simple-use, cost effective 17 β-estradiol biosensor system which can be used for both environment and women’s health care applications. The bio-recognition mechanism is based on the influence of the redox couple, K₃Fe (CN) ₆/K₄Fe (CN) ₆ by the interaction between 17 β-estradiol antigen and its α-receptor (ER- α; α-estrogen antibody). The transduction mechanism is an electrochemical analytical technique, differential pulse voltammetry (DPV). The levels of 17 β-estradiol antigen studied was between 2.25 pg/mL to 2,250 pg/mL, Phosphate buffered saline (PBS), tap water from the Cleveland regional water district, and simulate urine were used as the test media covering the potential application areas for 17 β-estradiol detection. An interference study by testosterone which has a similar chemical structure and molecular weight as those of 17 β-estradiol was carried out, and this 17 β-estradiol biosensor showed excellent specificity without any interference by similar chemicals.

Biohydrogen is a versatile energy carrier for the generation of electric energy from renewable sources. Hydrogenases can be used in enzymatic fuel cells to oxidize dihydrogen. The rate of electron transfer (ET) at the anodic side between the [NiFe]-hydrogenase enzyme distal iron-sulfur cluster and the electrode surface can be described by the Marcus equation. All parameters for the Marcus equation are accessible from DFT calculations. The distal cubane FeS-cluster has a three cysteine and one histidine coordination [Fe₄S₄](His)(Cys)₃ first ligation sphere. The reorganization energy (inner- and outer-sphere) is almost unchanged upon a histidine-to-cysteine substitution. Differences in rates of electron transfer between the wild-type enzyme and the all-cysteine mutant can be rationalized by a diminished electronic coupling between the donor and acceptor molecules in the [Fe₄S₄](Cys)₄ case. The fast and efficient electron transfer from the distal iron-sulfur cluster is realized by a fine-tuned protein environment which facilitates the flow of electrons. This study enables the design and control of electron transfer rates and pathways by protein engineering.

Recent advances in nanomaterials have been heavily influenced by low-dimensional nanocarbon allotropes. In particular, carbyne has attracted attention for its potential as a true one-dimensional carbon chain with sp1 hybridization. To maximize the capabilities of this material, we employ a focused data-driven inverse design approach based on the carbon nanomaterials genome concept. This involves using deep learning neural network models to identify key descriptors tied to desired properties, enabling property prediction and reverse engineering of nanocarbons. Our iterative approach entails: (i) gathering growth/property data on nanostructures; (ii) identifying informative numerical/categorical predictors; (iii) developing deep learning models mapping descriptors to properties; (iv) refining models with new insights; (v) determining required descriptors/conditions for target properties via inverse mapping; (vi) validating models by synthesizing predicted nanostructures; and (vii) enhancing models with validation data. This allows uncovering hidden growth-property connections, precisely tuning nanocarbons for desired attributes. We introduce new methodologies including exciting synergistic effects, synchronizing atomic vibrations, active screen plasma, energy-driven transformations, surface acoustic micro/nano-manipulation, doping and directed self-assembly to expose relationships and integrate insights into the inverse design flow. This research promises to accelerate discovery of next-generation low-dimensional nanocarbons with exceptional properties and applications.

This paper discusses the design and implementation of a portable IoT station. Communication and data synchronization issues in several installations are addressed here, making possible a detailed analysis of the entire system during its operation. The system proposed is interpreted as an additional tool which can be utilized in several applications, where the system operator requires a synchronized data stream, combining multiple communication protocols into one single time stamp. The hardware selected for the portable IoT station complies with the International Electrotechnical Commission (IEC) industrial standards. A short discussion regarding interface customization shows how easily the hardware can be modified so that it is integrated with almost any system. A Programmable Logic Controller enables the Node-Red to be utilized. This open-source programming tool employs flows to define operations for each global variable nominated in the Modbus register. Two applications are presented and discussed in this paper, each application has a distinct methodology utilized to publish and visualize the acquired data. The portable IoT Station is highly customizable, consisting of a modular structure and providing the best platform for future research and development of dedicated algorithms.

Vertical Indoor Farming (VIF) with hydroponics offers a promising perspective for sustainable food production. Intelligent control of VIF system components plays a key role in reducing operating costs and increasing crop yields. Modern machine vision (MV) systems use Deep Learning (DL) in combination with camera systems for various tasks in agriculture, such as disease and nutrient deficiency detection, and flower and fruit identification and classification for pollination and harvesting. This study presents the applicability of MV technology with DL modelling to detect the growth stages of chilli plants using YOLOv8 networks. The influence of different bird’s eye and side view datasets and different YOLOv8 architectures was analysed. To generate the image data for training and testing the YOLO models, chilli plants were grown in a hydroponic environment and imaged throughout their life cycle using four camera systems. The growth stages were divided into growing, flowering and fruiting classes. All trained YOLOv8 models showed reliable identification of growth stages with high accuracy. The results indicate that models trained with data from both views show better generalisation. YOLO’s middle architecture achieved the best performance.

This paper proposes a product design model for internalising users’ positive experiences through attachment. First, the research commences with a literature review to define the concepts and research status of positive experience design (PED) and product attachment. Subsequently, the design model is constructed, accompanied by relevant formulas for concept generation. Finally, the model’s validity is verified through a workshop, and its effectiveness is evaluated and discussed using the USE questionnaire. This study incorporates the seven factors of product attachment to activate positive states within the user–product relationship and facilitate the cultivation of positive thinking. Grounded in theories of PED and embracing a product attachment perspective, the attachment-driven PED model offers a systematic approach for generating design concepts that are relevant to user experience.

Rural landscapes are acknowledged for their potential to restore human health due to their natural characteristics. However, few studies have systematically analysed the impact of naturalness, landscape types, and combinations of landscape elements on restorativeness using both subjective and objective measurements. This study investigated the restorative effects of various rural landscapes in Guangzhou, employing electroencephalography and eye-tracking technologies to record physiological responses and using the Restorative Components Scale and the Perceived Restorativeness and Naturalness Scale to evaluate psychological responses. The results indicated the following: (1) There was a significant positive correlation between perceived naturalness and restorativeness, surpassing the impact of actual naturalness. (2) Different landscape types had a varying impact on mental health at the equal perceived naturalness. Natural forest landscapes and artificial forest landscapes exhibited the most substantial restorative effects among the natural and semi-natural landscapes examined, respectively, while settlement landscapes showed the highest restorative potential among the artificial landscapes. (3) Restorative properties varied across landscape elements, with identical elements yielding different benefits in different environments. Trees and water significantly enhanced restorativeness, whereas constructed elements such as roads and infrastructure reduced it. This study provides a scientific basis for restorative rural landscape design to enhance mental health and well-being.

Intense climate change and rapid urbanization have increased the risk of urban flooding, seriously affecting urban economic and social stability. Enhancing the urban flood resilience (UFR) has required a new solution to cope with urban flood disasters. In this study, taking Yingtan city as an example, a system of indicators for evaluating UFR was constructed, with 17 representative indicators, comprising three subsystems: socio-economic, ecological and infrastructural. A hybrid (FAHP-EWM)-TOPSIS model was applied, to develop an index-based measurement to compare and evaluate UFR, and Gray Relational Analysis (GRA) was used to discover the main factors affecting UFR. In addition, the natural discontinuous method was innovatively used to divide the UFR grade interval into levels, and the grade change was evaluated based on the TOPSIS method. The results showed that (1) from 2010 to 2022, the UFR in Yingtan City increased by 80.69%, and the factors affecting UFR are highly correlated with urban infrastructure development. However, the ecological resilience in the subsystem showed a fluctuating downward trend, because of the influence of the surface area of lakes and rivers. (2) The grades of UFR for Yingtan City increased from Level III (2010 and 2016) to Level IV (2022), with local financial expenditures and the age structure of the population being the main factors currently limiting the development of UFR. The study provides a theoretical basis for the construction of an indicator system for assessing the UFR of Yingtan and proposes practical improvement directions for UFR.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

China is experiencing rapid urbanization. The focus on health issues has shifted from the treatment of diseases to passive or active prevention. Diseases caused by the deterioration of the urban environment, such as cardiovascular disease, diabetes, obesity and other chronic diseases and mental illness, have gradually become the main threat to public health. Studies have confirmed that urban green spaces (UGS) can help residents relieve mental stress, improve mood, reduce mental fatigue and restore attention, which has a positive effect on people's physical and mental health. In this study, the relationship between the quantity and quality factors of UGS and the physical and mental health of urban residents in Xihu District of Hangzhou is examined, and on this basis, UGS design strategies are proposed to promote the physical and mental health of residents. This study is of great significance for the future construction of UGS that are beneficial to the health of residents and the promotion of a healthy China and healthy city construction.

This study investigates the spatial and temporal dynamics of Paomo restaurants in Xi'an's central urban area from 2012 to 2023, leveraging Point of Interest (POI) data through a series of sophisticated analytical techniques. Methods including nearest neighbor distance, kernel density estimation, and band set statistical analysis were employed to thoroughly examine the evolutionary patterns and key drivers influencing the spatial distribution of these eateries. Our results highlight a notable trend of expansion from the central city to the periphery, characterized by significant spatial agglomeration. Initially concentrated in the city center, the distribution of Paomo restaurants has progressively shifted towards multiple distinct cores, reflecting the dual influence of urban policy initiatives and the dynamics of market competition. Furthermore, the research identifies several pivotal factors shaping this spatial distribution, particularly transportation access, residential quality of life, and the availability of commercial services. These findings demonstrate the profound effects of urban spatial reconfiguration and socioeconomic development on the specialized catering industry. The insights gleaned from this analysis offer valuable guidance for urban planners and policymakers, providing strategic recommendations for the spatial planning of specialty catering services to optimize urban layouts and foster sustainable economic progress.

Ever since Varela and Maturana proposed the concept of autopoiesis as the minimal requirement for life, there has been a focus on cellular systems that erect topological boundaries to separate themselves from their surrounding environment. Here we reconsider whether the existence of such a spatial boundary is strictly necessary for self-producing entities. This work presents a novel computational model of a minimal autopoietic system inspired by dendrites and molecular dynamics simulations in three-dimensional space. A series of simulation experiments where the metabolic pathways of a particular autocatalytic set are successively inhibited until autocatalytic entities that could be considered autopoietic are produced. These entities maintain their distinctness in an environment containing multiple identical instances of the entities without the existence of a topological boundary. This gives rise to the concept of a metabolic boundary which manifests as emergent self-selection criteria for the processes of self-production without any need for unique identifiers. However, the adoption of such a boundary comes at a cost, as these autopoietic entities are less suited to their simulated environment than their autocatalytic counterparts. Finally, this work showcases a generalized metabolism-centered approach to the study of autopoiesis that can be applied to both physical and abstract systems alike.

Amid escalating urbanization, devising rational commercial space layouts is a critical challenge. Leveraging machine learning, this study uses a Back-propagation (BP) neural network to optimize commercial spaces in Weinan City's central urban area. The results indicate an increased number of commercial facilities with a trend of multi-centered agglomeration and outward expansion. Based on these findings, we propose a strategic framework for rational commercial space development emphasizing aggregation centers, development axes, and spatial guidelines. This strategy provides valuable insights for urban planners in small and medium-sized cities in the Yellow River Basin and metropolitan areas, ultimately showcasing the power of machine learning in enhancing urban planning.

A single qubit may be represented on the Bloch sphere or similarly on the 3-sphere S3. Our goal is to dress this correspondence by converting the language of universal quantum computing (UQC) to that of 3-manifolds. A magic state and the Pauli group acting on it define a model of UQC as a positive operator-valued measure (POVM) that one recognizes to be a 3-manifold M3. More precisely, the d-dimensional POVMs defined from subgroups of finite index of the modular group PSL(2, Z) correspond to d-fold M3- coverings over the trefoil knot. In this paper, one also investigates quantum information on a few ‘universal’ knots and links such as the figure-of-eight knot, the Whitehead link and Borromean rings, making use of the catalog of platonic manifolds available on the software SnapPy. Further connections between POVMs based UQC and M3’s obtained from Dehn fillings are explored.

A single qubit may be represented on the Bloch sphere or similarly on the $3$-sphere $S^3$. Our goal is to dress this correspondence by converting the language of universal quantum computing (uqc) to that of $3$-manifolds. A magic state and the Pauli group acting on it define a model of uqc as a POVM that one recognizes to be a $3$-manifold $M^3$. E. g., the $d$-dimensional POVMs defined from subgroups of finite index of the modular group $PSL(2,\mathbb{Z})$ correspond to $d$-fold $M^3$- coverings over the trefoil knot. In this paper, one also investigates quantum information on a few \lq universal' knots and links such as the figure-of-eight knot, the Whitehead link and Borromean rings, making use of the catalog of platonic manifolds available on SnapPy. Further connections between POVMs based uqc and $M^3$'s obtained from Dehn fillings are explored.

Presently, Jordan confronts a double substantial challenge of enhancing energy security and mitigating greenhouse gas emissions. One of the most encouraging avenues to attain the objectives of sustainable development, energy security, and environmental conservation is to enhance the integration of renewable energy into the generation of electricity. In pursuit of this goal, the Jordanian government intends to expand investments in the green energy sector, with solar and wind energy poised to play a key role in satisfying energy demands and cultivating an environmental sustainability. This paper aims to examine the distinctive dynamics, challenges, obstacles, and potential solutions corresponding to the establishment of community solar and wind farms in Jordan suburban areas. It aims to highlight the opportunities and barriers influencing the track of sustainable energy adoption in the country. Through a comprehensive analysis of the Jordanian context, the goal is to extract insights that can guide policies and practices. Additionally, the findings may serve as a valuable benchmark for other regions confronting similar challenges on their pursuit for a sustainable energy future.

This paper presents laboratory devices on which experimental measurements were carried out to prove the validity of the assumption about the reduction of vibrations transmitted to the conveyor belt structure generated by the impact forces of falling material grains in the places of transfer or on the hoppers of conveyor belts. In order to limit damage to the conveyor belts caused by the impact of the sharp edges of material grains, conveyor belts are supported by impact rollers or impact rubber rods in the places of transfers and on the hoppers of belt conveyors. The flattened ends of the impact rollers are inserted into the grooves of steel brackets installed on the supports of the fixed conveyor idlers of a conventional design. In this paper, a special modification of the fixed conveyor idler is presented, which consists of inserting plastic brackets into the structurally modified roller axle holders of the fixed conveyor idler. Measurements were carried out on the first laboratory device, which showed that the specially modified fixed conveyor idler resulted in a higher damping of up to 15% of the impact forces of the falling weight on the rubberized hoop of the impact roller shell compared to the conventional fixed conveyor idler design. Measurements carried out on the second laboratory device show that the effective vibration velocity values detected at the points where the impact roller axis fits into the fixed roller table holder, i.e. points B and D, are higher than when using plastic brackets, up to 6% for a 108 mm diameter roller, compared to steel impact roller brackets.

The graphene based highly conductive and flexible devices has received momentous attraction and growth in recent years for potential multifunctional uses. The development of flexible and washable textile sensors, actuators, energy storage and energy harvesting systems. Textile fabrics coated with graphene and conductive polymers have been used for wearable self-powered e-textiles, such as tribo-electric, piezoelectric, and Thermoelectric. Herein this research, 100% woven cotton fabric is Fictionalized with graphene oxide (GO) using industrial-scale cold pad batch dyeing technique for the development of low-grade body heat into self-powered wearable e-textiles. The conductive polymer PEDOT: PSS was coated using layer by layer approach. The study demonstrates that the resultant textile electrodes showed reduced electrical sheet resistance from 2.5 MΩ to 15KΩ, with a reduced graphene oxide and further reduced to (2.5 -12.5 Ω) for conductive polymer. The sheet resistance was decreased with the number of dyeing cycles (10-15) and increased with 20 washing cycles vice versa. The study demonstrates that the sensor response and performance were improved with increasing the content percent of rGO and PEDOT: PSS. The tensile strength of as coated fabric electrodes was improved from (25.0-85.5 mPa) and fabric thickness was increased to (26-38µm) without compromising or influencing the air permeability. The resultant textile electrodes may potentially be used in smart textiles for self-powered flexible wearable generators, sensors, and energy storage. The study demonstrates that the cold pad batch dyeing method is a suitable and effective method for the fabrication of graphene-based textiles.

This study introduces an advanced dual-mode composite attitude control framework for reusable launch vehicles (RLVs), underpinned by an enhanced particle swarm optimization (PSO) algorithm. This innovative strategy is tailored to meet the stringent demands for precision and robust anti-interference capabilities across the entire flight envelope of RLVs. The research commences with the formulation of a comprehensive attitude dynamics model and diverse heterogeneous actuator representations, meticulously crafted to reflect the distinct phases of RLV flight. Building upon this foundation, a synergistic control paradigm is engineered, integrating PID and fuzzy PID controllers, complemented by a refined fitness evaluation function. The crux of the study is the application of an upgraded PSO algorithm to fine-tune the controllers' weighting coefficients, culminating in an optimized dual-mode composite attitude control system. A series of comparative simulation analyses are meticulously executed to appraise the system's responsiveness, stability, precision, and resilience to interference. The findings unequivocally substantiate the superior performance of the proposed control system, affirming its substantial contribution to the advancement of RLV attitude control.

Surface acoustic wave (SAW) is effective for the manipulation of fluids and particles in microscale. The current approach of integrating interdigitated transducers (IDTs) for SAW generation into microfluidic channels involves complex and laborious microfabrication steps. These steps often require the full access to clean room facilities and hours to align the transducers to the precise location. This work presents an affordable and innovative method for fabricating SAW-based microfluidic devices without the need of clean room facilities and alignment. The IDTs and microfluidic channels are fabricated in the same process and thus precisely self-aligned in accordance with the device design. With the use of the developed fabrication approach, a few types of different SAW-based microfluidic devices have been fabricated and demonstrated for particle separation and active droplet generation.

The three-pronged sliding universal coupling is a new kind of three-pronged coupling. To study its kinematic and dynamic characteristics, directional cosine matrices are utilized as tools to analyze the coordinate systems by establishing simplified geometric models and corresponding motions. Through the analysis of the motions of the input and output shafts and employing the method of single-force element, a set of equilibrium equations for the forces acting on the output shaft and the input shaft are formulated for solution analysis. The research indicates that during the rotation process, there exists a small angular difference between the input shaft and the intermediate shaft, demonstrating the quasi-constant angular velocity characteristics of the new tripod sliding universal coupling. The curves of the forces and torques acting on each component of the coupling approximate sinusoidal curves. The optimal operating angle range for the new tripod universal coupling is at angle , during which the system exhibits good transmission and mechanical performance.

In mining machines with friction discs, but also in multi-rope traction elevators, it is necessary to distribute the applied tensile load, generated by the weight of the cage and counterweight, evenly in all cross-sections of the load-bearing ropes. Hydraulic devices used for this purpose can operate on the principle of Pascal's law. The article presents a structural design, a 3D model and an implemented solution of a laboratory device capable of simulating a practical method of evenly distributing the total weight of the load into partial tensile forces of the same size acting on a selected number of load-bearing ropes. The laboratory equipment uses two pairs of three steel cables of finite length for the simulations. During the experimental measurements, tensile forces derived from the tractive force of the piston rods, pushed into the bodies of the hydraulic cylinders by the pressure of the hydraulic oil supplied through the pipeline under the pistons of the hydraulic cylinders, were detected. The resulting amount of hydraulic oil pressure in the hydraulic circuit influenced by different values of the hydraulic oil pressures in the hydraulic cylinders and by the pressure in the supply pipe was experimentally studied on the laboratory equipment. Simulations were also carried out in order to detect the hydraulic oil pressure in the hydraulic circuit caused by the change in the different magnitudes of the tensile forces in the ropes From the experiments carried out, it follows that with the appropriate choice of hydraulic elements and the design of the hydraulic circuit, the weight of the load, acting as the total pulling force in the ropes, can be evenly distributed (with a deviation of up to 5%) to all cross-sections of the load-bearing ropes. If the exact values of the hydraulic oil volumes under the pistons of all hydraulic cylinders are not known, it is not possible to calculate the pressure values in the hydraulic circuit when the valves of the hydraulic pipes are gradually opened.

Universal gravitation is investigated with principles of foundational classical (Newtonian) physics. The results reveal gravitation an atomic field action; hence, Newton’s law, although absolutely valid, unavoidably misleads in creating the impression of matter rather than waveform action. Six force constants fully define gravitation: (i) a waveform torque field ; (ii) an expansion force field ; (iii) a centripetal force field ; (iv) a matter-wave torque field (the force fields , and constitute gravitational inertial rest frame); (v) a Galilean acceleration field and (vi) nuclear inverse mass-squared centripetal force constant The inertial rest frame force constants sum up to give observational G = 2.266 + 2.61 + 2.61cos46^o) x 10^-11 = 6.689 x 10^-11 m³ kg^-1 s^-2. Notably, the procedure is able to account also for observational inclination of galaxies and their aligned conjunctions. An attempt is made to account for angular momentum quantization and rectilinear, parabolic or elliptic profile of objects in gravitational acceleration. Same quantitative expression, , defines the photon and gravitation thus uniquely unifying gravitation, electricity and magnetism; furthermore, the expression reveals the photon packed with tremendous energy amounting to some . It is argued that: (i) neither mass nor gravitation curves spacetime; (ii) the principles that sustain cosmic time-scale dynamic equilibrium, scale invariance and inertia are incompatible with quantum gravitation; and (iii) the cosmic vacuum field comprises gravitational (photonic) waves, hence the interferometer likely measures shock waves.

This paper is based on the concept of absolute airspace and its local absolute stationary reference system proposed by the author, on the premise of abandoning space concept and the relativity principle of relativity theory, It is proposed that general relativity and special relativity can be unified into Simple and practical a space-time transformation theory which fully includes other basic physical principles of relativity. And the unified and simple expression of the time transformation effect is proved and deduced. By comparing with the theoretical derivation and checking calculation of Hafele-Keating experiment in an ideal state, It is proved that the expression of time transformation effect proposed in this paper is completely correct. Compared with the theory of relativity, the calculation is simpler and more accurate. The paper also puts forward two checking prediction of physical cases about the time transformation effect, which are left for the capable competent unit or individual to verify in practice.

The paper suggests that the physical priciple of special relativity's space-time transformation effect is wrong, Uniform linear motion without acceleration does not exist objectively, nor does its same reference frames. Therefore, it is inferred that the space-time transformation effect of special relativity is caused by the acceleration of moving objects, special relativity is only a part of general relativity, not a theoretical system that exists independently from general relativity. The corresponding mathematical demonstration and calculation verification are carried out, and the result proves that the inference of the paper is correct. At the same time, it further explains that the concept of absolute airspace is correct. Special relativity has serious errors in the concept of space, the principle of relativity and the physical principle of space-time transformation effect. Therefore, it is necessary to make a series of revisions to the theory of relativity and to reinterpret some related physical problems.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth's surface can generate a radial centrifugal force of the Earth's center of mass, thus realizing an unconventional anti-gravity path. And through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth's surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for antigravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

In this paper, the Hafele‐Keating experiment and the geostationary orbit satellite of related physics problems of are analyzed and discussed in detail. If researchers read the paper and think about it, It will be found that the Hafele‐Keating experiment and the geostationary satellite problem prove that some of the core ideas and theories of relativity are seriously wrong. Isnʹt that a very serious problem in physics? Canʹt this cause the academic circles to pay great attention to it? Isnʹt this worthy of in‐depth analysis and research? The core of the paper is to point out that there are problems with the space concept and the reference system theory of classical physics and relativity, And that would bring up a whole host of physics problems. It takes a concerted effort from the academic community, Do furtherin‐depth analysis and research. Strive forthe further discovery and perfection of physics theory.

In order to tackle the issue of severe rocking phenomenon under seismic conditions in structures equipped with steel spring isolation bearings, this paper investigates a novel type of anti-rocking bearing. Firstly, the structural configuration and working principle of the novel anti-rocking bearing are introduced, and a design method for bearing parameters is proposed. Secondly, a finite element analysis model is established using SAP2000 software to conduct nonlinear dynamic time history analysis under seismic loading. The analysis results show that the structural arrangement of the novel anti-rocking bearing reduces both the vertical displacement difference and the rocking angle of the isolation layer. The bearing exhibits a certain level of anti-rocking effect, but it may cause significant tensile forces in some bearings, necessitating the installation of anti-tensile reinforcement. The effectiveness of the anti-rocking effect improves as the stiffness of the steel tension rod in the bearing increases; however, it also leads to higher maximum tension in individual bearings as well as the total tension in all bearings. For structures equipped with the novel anti-rocking bearing, the acceleration amplifies under most cases, with amplification coefficients ranging from 0.82 to 1.55. The performance of the novel anti-rocking bearing varies significantly for different seismic waves. The stiffness of the steel tension rod should be determined considering the reference pressure of the bearing and the maximum designed tension of the bearing. Through the finite element simulation of the bearing, the mechanical properties of the bearing are basically the same as the theoretical analysis results. For the cylinder and the joint bearing, certain structural measures need to be taken to ensure its strength and stiffness.

In the present work, a predictive modelling and optimization with the adaptive network based fuzzy inference system(ANFIS) modelling of mechanical properties of laser-coated NB/SiC/Ni welds was studied based on Taguchi design by laser cladding. An ANFIS model based on a Sugeno type fuzzy inference system was developed for predicting the hardness properties of SiC/BN/Ni welds by laser cladding with experimental data required for network training and prediction. Based on analysis of variance, three important factors were taken as inputs for the fuzzy logic inferences, while the hardness properties was taken as the output of the ANFIS. The microstructure of welds were analysed using scanning electron microscopy with an energy dispersive X-Ray spectrometer. Highly developed leaf-like dendrites and eutectic crystals were found in some areas of the melting zone for the BN/SiC/Ni weld, which was significantly hardened. The ANFIS model based on Taguchi's design provides a better pattern of response because the predicted and experimental values were highly similar. As a result, a satisfactory result was achieved between the predicted and experimental values of hardness in laser-coated NB/SiC/Ni welds, whereby the success and validity of the method was verified.

The rapid growth of the global wearable technologies market is projected to reach $61.30 billion by 2030 which reflects a shift towards personalised health monitoring embedded in everyday activities. This paper explores the potential of embroidered interdigitated transducer (IDT)-based sensors for non-invasive, continuous monitoring of human biomarkers, particularly glucose levels, in human sweat. The study employs innovative embroidery techniques to create flexible fabric-based sensors with gold-coated IDTs. Experimental results demonstrate the sensor’s capability to detect water droplets and glucose concentrations, showcasing promising applications for health monitoring. The embroidered IDT-based sensors offer a unique approach for seamless integration into clothing, paving the way for personalised, continuous health data capture.

Steel fibre reinforced concrete (SFRC) consists of short hooked steel fibres randomly distributed and oriented within the cementitious matrix. The contribution of fibre in bridging cracks to provide the stress transfer required relies upon the orientation of the fibre in the concrete. Bridging fibre aligned with a crack are less effective than those inclined to it. Therefore, understanding the pull-out behaviour of misaligned fibre is a key factor to quantify and optimize the design of SFRC in the structural applications. In the laboratory a single oriented fibre embedded in a solid cylinder of concrete is subjected to a pull-out test where the axis of a tensile force is aligned with the axis of the cylinder. Based upon the observed behaviour this paper presents a new analytical bounding approach to capture the pull-out response of misaligned hooked-end steel fibre embedded in a concrete matrix. The analysis is based upon a transversely isotropic condition assumed for the plasticity that occurs in the cold drawn fibre. The model accounts for the influence of fibre diameter and the combined strengths of the steel and concrete. The model predictions have also been compared with other experimental results published in the literature. The results showed that the model can predict pull-out loads reasonably for different fibre orientations between bounds of failure derived from the strengths of the two constituents. A critical orientation is observed at maximum strength. Therein, an understanding of the pull-out behaviour of misaligned, hooked-end fibres is necessary to optimize the strength of concrete from this method of reinforcement.

The blood counts of α thalassemia carriers (α-thal) are similar to those of β thalassemia carriers, except for Hgb A2 that is not elevated. The objective of this study was to determine whether mathematical formulas are effective for detecting suspected α-thal. The data were obtained from the database of the prevention program for detecting couples at risk for having a child with hemoglobinopathy. RBC indices were analyzed using mathematical formulas and the sensitivity and negative predictive value (NPV) calculated. Among 1334 blood counts suspected α-thal analyzed, only the Shine&Lal and the Support Vector Machine formulas revealed high sensitivity and NPV. Sensitivity was 85.54 and 99.33% and NPV 98.93 and 99.93%, respectively. Molecular defects were found in 291, 81 had normal α genes. Molecular analysis was not performed in 962. Based on these results, mathematical formulas incorporating one of these reliable formulas for detecting suspected α or β thalassemia carriers in the program of the automatic analyzers can flag these results and increase the awareness of the primary physicians about the carrier risk and send an alert with a recommendation for further testing.

This paper presents a comprehensive analytical-numerical algorithm constructed for proprotor performance evaluation, focusing on accommodating large inflow angles. The algorithm’s design, range, and analytical features are clarified, indicating its potential to improve performance analysis, particularly for blades with substantial pitch variations. The Stahlhut model has not been validated against the conventional BEMT small-inflow angle methodology. This paper implements a modified Stahlhut model, coupled with the conventional BEMT theory. Preliminary validations of the model demonstrate promising results, with deviations reduced to -3% to 4% compared to conventional BEMT methods exhibiting deviations as high as 20% to 88% against experimental data for a highly twisted proprotor. The reconsideration of the computational module carries considerable implications for the design and refinement of proprotors, providing alternative analysis methods that could improve operational effectiveness across a range of flight scenarios. Drawing upon the theoretical framework presented by Stahlhut, the algorithm enables a more complex understanding of proprotor dynamics, facilitating accurate predictions of the loads at each blade section. The introduced algorithm emerges as a valuable asset for evaluating proprotor performance during the early stages of design and certification, offering both low computational cost and medium to high reliability.

Involving local people in natural area management is very important to address the complexity of environmental management issues for sustainable use of local resources. Participatory methods require the contribution of local stakeholders in decision making. Mapping the environmental views of local communities allows for detecting aspects that could facilitate management efforts. This research – in the frame of the Skyros LIFE project and the PAMNATURA project - measures local acceptability of the conservation actions proposed by the LIFE project in Skyros Island (Greece) in relation with recording local people’s environmental orientation using the 15-item revised New Ecological Paradigm (NEP) scale. The research was carried out by means of questionnaires. The LIFE project proposed actions were grouped into three categories according to their theme, i.e. promoting (a) Nature protection, (b) Agro-pastoralism and (c) Ecotourism. The sample seems to largely agree with the LIFE project proposals, while the results showed high scores for most of the NEP scale items, implying pro-environmental beliefs, though there appears disagreement or neutrality regarding a few items. Local acceptability of the proposed actions was found to correlate to local people’s environmental concern measured through the NEP scale. Drawing on the results, implementation of actions related directly or indirectly to economic activities, preservation of traditional activities, as well as environmental education, interactive informing and consultation could enhance local participation. Skyros island seems to offer an appropriate social background for applying participatory and adaptive management and implementing conservation programs.

A novel method for finding linear mappings among word embeddings for several languages, taking as pivot a shared, universal embedding space, is proposed in this paper. Previous approaches learn translation matrices between two specific languages, but this method learn translation matrices between a given language and a shared, universal space. The system was first trained on bilingual, and later on multilingual corpora as well. In the first case two different training data were applied; Dinu’s English-Italian benchmark data, and English-Italian translation pairs extracted from the PanLex database. In the second case only the PanLex database was used. The system performs on English-Italian languages with the best setting significantly better than the baseline system of Mikolov et al. [1], and it provides a comparable performance with the more sophisticated systems of Faruqui and Dyer [2] and Dinu et al. [3]. Exploiting the richness of the PanLex database, the proposed method makes it possible to learn linear mappings among an arbitrary number of languages.

In areas with a deep floor plan, the distribution of natural light is not uniform. Consequently, relying solely on daylight may not suffice to meet the space's lighting requirements, necessitating the use of artificial lighting in darker areas. Therefore, a lighting system is needed that not only controls the glare near the windows but also increases the light at the end of the room and provides uniform daylight. One of the widely used systems is the “light shelf“which has three main functions: shading, increasing the depth of light penetration and reducing glare. Review articles about light shelves have been done in 2015 and 2017, while more than 80% of the studies have been carried out since 2016 and light shelves with more diverse forms and dynamic elements and many consolidations were proposed. Therefore, there is a need for a more comprehensive review. The main question of this research is how different parameters (including climate, material, ceiling and integrated systems) can help to increase the efficiency of light shelves. By using a systematic review, studies in the past three decades were classified in order to determine the effect of these parameters on improving lighting performance and controlling solar heat gain.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

In this work, an analytical and numerical analysis of the transition to chaos in five nonlinear systems of ordinary and partial differential equations, which are models of the autocatalytic chemical processes and the numbers of interacting populations, is carried out. It is analytically and numerically shown that in all considered systems of equations, further complication of the dynamics of solutions and the transition to chemical and biological turbulence is carried out in full accordance with the universal Feigenbaum-Sharkovsky-Magnitskii bifurcation theory through subharmonic and homoclinic cascades of bifurcations of stable limit cycles. In this case, irregular (chaotic) attractors in all cases are exclusively singular attractors in the sense of the FShM theory.

The Standard Model (SM) fails to account for either the triplication of fermion families or chiral symmetry breaking in the electroweak sector. Here we show that both phenomena arise from the approach to chaos of quantum theory near the Fermi scale.

In this study, a new type of temperature sensor device was developed. The circular electrode of the thermal sensitive sensor was modified with TMT and O₂ plasma to enhance the conductivity by forming a thin SnOxCy layer on the electrode surface. The Nano-Au particles were subjected to O₂ plasma pretreatment to form peroxide groups on the surface. The thermally sensitive sensor was made by mixing the above-treated Nano-Au particles with N-isopropylacrylamide (NIPAAm) to form solution and then UV-induced grafting polymerization of the NIPAAm-containing solution onto the electrode substrate. The composite hydrogels on the electrode introduce thermo-sensitive polymeric surface films for temperature sensing. Using ambient environment resistance test to measure the resistance, the LCST (lower critical solution temperature) of Nano-Au (MUA) mixed with NIPAAm hydrogel was found to be 32 °C. At ambient temperatures higher than LCST, the electrode resistance decreases linearly.

To address the response of small RNAs (sRNAs) biogenesis to drought stress, we identified sRNAs biogenesis genes, including 11 encoding argonauts (AGO), 8 encoding dicer-like proteins (DCL), and 9 encoding RNA-dependent RNA polymerases (RDR) in the peach genome. Notably, the largest numbers of sRNAs biogenesis genes are located to chromosome 1. The PAZ, PIWI, and MID domains were identified in PpAGOs, while the ribonuclease IIIa and IIIb domains were characterized in PpDCLs. The RDRP domain was recognized in PpRDRs. Orthologous similarity and collinearity analyses between Arabidopsis and peach revealed 5, 1, and 2 collinear blocks in AGOs, DCLs, and RDRs, respectively. Moreover, 41, 40, and 42 cis-acting elements were located in the promoters of PpAGOs, PpDCLs, and PpRDRs, respectively, with the majority related to drought stress response. Analysis of RNA sequencing (RNA-seq) data revealed that sRNAs biogenesis genes were involved in drought stress response in different tissues. Furthermore, the expression of candidate genes was verified in two peach cultivars, Beijing 2-7 (BJ2-7) and Sinai (SN), which are drought tolerance and sensitive, respectively. Interestingly, the expression of PpAGO2b, PpDCL2b, PpDCL4, and PpRDR4 genes was induced in ‘BJ2-7’ but inhibited in ‘SN’ under drought stress. Overall, this study provides insight into the roles of sRNA biogenesis genes in response to drought stress in peach.

To fulfil a need of limitation automotive emissions the reduction of vehicle weight is widely recommended and achieved in many ways, both by the construction of individual elements of the vehicle, and by the selection of light materials including Al alloys. Connecting these elements with each other and with elements made of iron alloys can be realized, inter alia, by welding or stir welding. However, the quality of the welds obtained varies widely and depends on many design, operational and environmental factors. The present study focused on a review of various welding technics used to joint both similar and dissimilar Al alloys utilized in automotive industry, the effect of various process parameters on welds quality, and phenomena appeared in such welds..

This study presents an advanced Simulated Shearer Machine Cutting Experiment System enhanced with digital twin technology. Central to this system is a simulated shearer drum, designed based on similarity theory to mirror the operational dynamics of actual mining cutters accurately. The setup incorporates a modified machining center equipped with sophisticated sensors that monitor various parameters such as cutting states, forces, torque, vibration, temperature and sound. These sensors are crucial for precisely simulating the shearer cutting actions. The integration of digital twin technology is pivotal, featuring a real-time data management layer, a dynamic simulation mechanism model layer, and an application service layer that facilitates virtual experiments and algorithm refinement. This multifaceted approach allows for in-depth analysis of simulated coal cutting, utilizing sensor data to comprehensively evaluate the shearer's performance. The study also includes tests on simulated coal samples. The system effectively conducts experiments and captures cutting condition signals via the sensors. Through time-domain analysis of these signals, gathered while cutting materials of varying strengths, it is determined that the cutting force signal characteristics are particularly distinct. By isolating the cutting force signal as a key feature, the system can effectively distinguish between different cutting modes. This capability provides a robust experimental basis for coal-rock identification research, offering significant insights into the nuances of shearer operation.

Residential segregation refers to the phenomenon where people of different socioeconomic backgrounds live in spatially separated areas. It is essential to ensure equitable access to urban amenities for all residents in pursuit of the normative values in urban planning. To achieve this planning goal, the disparity in accessibility to urban amenities needs to be appropriately diagnosed. Private apartments and public rental apartments are representative types of residences where residential segregation is likely to occur in the context of South Korea, since these two types show considerable differences in the education, income, and occupations. The objective of this study is to develop an analysis framework for diagnosing the difference in accessibility to urban amenities between the two residential types, and to empirically demonstrate their utility in the planning process. The empirical analysis conducted on Seoul revealed that not only were there significant local variations in accessibility between the two segregated residential areas, but the overall differences across the entire area were also pronounced. The proposed framework is useful in supporting decision-making processes for locating new public facilities or identifying regional priorities for guiding the placement of private amenities, with the aim of mitigating differences between segregated residential areas.

This paper describes an entropy equation that can be used for measuring energy. It originated from measuring economy in AI models, where the assumption would be that any organic system makes use of energy efficiency to form its structures. Looking at clustering and cohesion resulted in the equation E = (mean * variance). It was apparent however, that it was a very generic type of equation and it could be adjusted so that distance represents mean. This new version was applied to the domain of physics and the universe, when the equation can support the idea that work is done through the energy released by the 'change' in entropy. A comparison with Einstein's relativity equation is made and also the audacious suggestion that a black hole has only potential energy inside, which converts to kinetic energy after a Big Bang, for example. From that suggestion, a universal theory about state change can be made.

The hydraulic fracturing is studied by using dimensional analysis. A universal scaling law of the hydraulic fracturing is obtained. This simple relation has not been seen in the literature.

We propose a novel interpretation of consciousness and an enlarged definition of locality, which provide a solution to the problem of the consistency of measurements in quantum mechanics: consciousness is a characteristics of the Universe as a whole. Besides its physical conse- quences, this interpretation has also moral implications: individuality comes out naturally to be just an accident functional to evolution which shaped past and present history through competition, and re- alizing this fact should enforce cooperation.

With reference to our earlier published views on large nuclear gravitational constant , nuclear elementary charge and strong coupling constant , in this paper, we present simple relations for nuclear stability range, binding energy of isotopes and magic proton numbers.

To protect skin from harmful ultraviolet (UV), zinc oxide (ZnO) with tannin from gallnuts was treated on cotton and polyester fabrics in this study. Before the treatments, the fabrics were dyed with shikonin and xanthophyll from Gromwell and Cape Jasmine. First, this study found that xanthophyll was more effective at preventing light fade or discoloration than shikonin. Despite the highest K/S, the untreated cotton in violet faded the most intensely when exposed to UV. The color variation of untreated polyester was narrow, with little change in L, a*, and K/S. Due to the non-photochemical xanthophyll, the yellow-dyed samples treated with ZnO/polyphenol did not vary yellowness (b*: 28.838) significantly, while the violet fabrics displayed a significant decrease in K/S and an increase in b*. The combination of ZnO and polyphenol treatment improved UV absorption at 350 to 250 nm. Cu-mordanting after ZnO/polyphenols treatment caused the violet cotton to turn reddish from blueish (negative to positive b*), with a hue change of 316° to 59° and the highest ΔE (25.90±4.34) after UV exposure. In this study, the combination of ZnO/polyphenol with Cu-mordants contributed the xanthophyll-dyed polyester to achieve a minimum ΔE and keep chroma and hue after UV exposure.

Studies have demonstrated the critical role that safety plays in preserving favourable working conditions in the construction industry, which is necessary to accomplish goals. The aim of this research was to inform stakeholders in the construction industry in developing nations about the value of safety and possible strategies for influencing their opinions regarding safety protocols. The importance of safety to the construction sector, which is crucial to the advancement of the country, has also been emphasized. However, due to a lack of adequate safety understanding among stakeholders in the construction sector, the construction industry is characterized by a great deal of instability and hazard. To determine what factors, affect productive working conditions in the construction production, this study examined safety. A conceptual framework for safe working conditions in the construction sector was developed by considering several aspects, including the person dimension, environment factor, safety behaviour, organization features, technology, and incentives. It is now imperative to bring in these dimensions to improve the safe working conditions in the construction industry, particularly in the developing countries. By putting these safety factors into practice, the construction industry can reduce safety risks, lower the number of accidents and fatalities, cut expenses related to subpar safety performance, safeguard the reputation of construction companies, boost employee morale and satisfaction with their work, enhanced employee retention, reduced absenteeism, and enhanced sustainability goals. Additionally, the proposed conceptual framework is assured to be new and to be widely accepted in the developing nations. Based on this assumption the conceptual framework is designed.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

Brand visual identity is a critical component of brand image and impacts consumers' brand perception and attitude. Although scholars and practitioners have increasingly researched brand visual identity, most focus on brand communication and corporate management perspectives, necessitating a systematic review of consumer attitudes based on brand visual identity elements. This study aims to review the impact of brand visual identity on consumer attitudes and provide directions for future research. We conducted a systematic search using PRISMA guidelines, reviewed relevant articles published in four databases (Web of Sciences, ProQuest, Scopus, and Elsevier) in the past two decades (2004-2024), and obtained 559 articles in April 2024. We conducted a thorough peer-review of both theoretical and empirical journal articles, followed by a scoping review. Thirty-four studies were eligible, analysing consumers' perceptions of various core elements of brand visual identity (BVI) (such as brand logo, colour, name, typography, and font), as well as the impact of brand visual identity on consumer attitudes and the practical implications of brand management. The results show that the consumption of visual identification elements affects consumers' perceived brand quality, brand personality, brand satisfaction, loyalty, favourability, and so on., as well as purchase intentions and social attitudes. In summary, the findings indicate that brand visual identity elements impact consumer perceptions and attitudes. However, despite some progress, further research is necessary to arrive at more definitive and robust conclusions.

The existence of a common ancestor to all living organisms in Earth is a necessary corollary of Darwin idea of common ancestry. The Last Universal Common Ancestor (LUCA) has been normally considered as the ancestor of cellular organisms that originated the three domains of life: Bacteria, Archaea and Eukarya. Recent studies about the nature of LUCA indicate that this first organism should present hundreds of genes and a complex metabolism. Trying to bring another of Darwin ideas into the origins of life discussion, we went back into the prebiotic chemistry trying to understand how LUCA could be originated under gradualist assumptions. Along this line of reasoning, it became clear to us that the definition of another ancestral should be of particular relevance to the understanding about the emergence of biological systems. Together with the view of biology as a language for chemical translation, on which proteins are encoded into nucleic acids polymers, we glimpse a point in the deep past on which this Translation mechanism could have taken place. Thus, we propose the emergence of this process shared by all biological systems as a point of interest and propose the existence of this pre-cellular entity named FUCA, as the First Universal Common Ancestor. FUCA was born in the very instant on which RNA-world replicators started to be capable to catalyze the bonding of amino acids into oligopeptides. FUCA has been considered mature when the translation system apparatus has been assembled together with the establishment of a primeval, possibly error-prone genetic code. This is FUCA, the earliest ancestor of LUCA’s lineage.

Background: Atopic dermatitis is a chronic condition that significantly affects the daily life of those who suffer from it, requiring complex and personalized management with active participation of the patient in the management of their disease. Objective: to describe the design and development process of a mobile application, using the Design Thinking method, for the follow-up of patients with atopic dermatitis. Methods: User-centered design and prototype creation method, differentiating the phases of the empathize, define, idea, prototype, and test. A purposive snowball sampling was used to recruit patients with atopic dermatitis, family members, and health professionals. Three two-hour workshops were held, attended by 25 people. Results: the parameters to be monitored will include objective data (physical, behavioral, treatments, environmental, integration of daily routines) and subjective data (user experience). On the other hand, it will figure out behavior patterns, set up rewards, foster a feeling of community, and use notifications and a chatbot. Conclusion: The active integration of all stakeholders at each stage of the design and development of the digital solution has improved its relevance and acceptance, resulting in a tool that is expected to significantly improve the management of atopic dermatitis.

Human Immunodeficiency Virus (HIV) infection and its latent recurrent infection make vaccine development a significant challenge for traditional vaccines; however, the mRNA delivery of multiepitope antigens capable of creating antibodies against the surface proteins of HIV-1 and HIV-2 along with their respective Nef proteins, responsible for the latent infection can bring a most effective, as well as affordable solution to the unresolved epidemics of HIV. In this paper, we present the complete design of a multiepitope vaccine to prevent acute infections and inactivate Nef proteins that block the MHC-1 and MHC-2 pathways to hide the virus for later reinfection.

Examining contemporary developments and cutting-edge approaches in the field, this literature review explores how antenna design for transmission lines is changing. Review findings are compiled from a variety of academic sources, including pertinent technical reports published as recently as 2018, conference papers, journal articles, and reports. A variety of antenna topologies suited for transmission lines are evaluated in this paper, including microstrip, slot, and patch antennas, with a focus on theoretical frameworks and practical implementations. This overview clarifies the complex relationship between antenna design and transmission line characteristics by looking at important factors like impedance matching, bandwidth, and radiation pattern management. Notable developments in materials, fabrication methods, and numerical simulations are also examined and their effects on antenna performance explained. Through a comprehensive analysis of the literature, this review offers valuable insights into the state-of-the-art antenna design practices for transmission lines, facilitating informed decision-making and inspiring future research endeavors in this field.

Dengue (DENV) and Zika (ZIKV) virus continue to pose significant challenges globally due to their widespread prevalence and severe health implications. Given the absence of effective vaccines and specific therapeutics, targeting of the highly conserved NS5 RNA-dependent RNA polymerase (RdRp) domain has emerged as a promising strategy. However, limited efforts have been made to develop inhibitors for this crucial target. In this study, we employed an integrated in silico approach utilizing combinatorial chemistry, docking, molecular dynamics simulations, MM/GBSA, and ADMET studies to target the allosteric N-pocket of DENV3-RdRp and ZIKV-RdRp. Using this methodology, we designed lycorine analogs with natural S-enantiomers (LYCS) and R-enantiomers (LYCR) as potential inhibitors of non-structural protein 5 (NS5) in DENV3 and ZIKV. Notably, 12 lycorine analogs displayed a robust binding free energy (<-9.00 kcal/mol), surpassing that of RdRp-Ribavirin (<-7.00 kcal/mol) along with promising ADMET score predictions (<4.00), of which (LYCR728-210, LYCS728-210, LYCR728-212, LYCS505-214) displayed binding properties to both DENV3 and ZIKV targets. This study highlights the potential of non-nucleoside lycorine-based analogs with different enantiomers that may present different or even completely opposite metabolic, toxicological, and pharmacological profiles as promising candidates for inhibiting NS5-RdRp in ZIKV and DENV3, paving the way for further exploration for the development of effective antiviral agents.

The Universe at last scattering is locally treated as an unbound gas. The internal kinetic energy of the gas effectively constitutes a scalar energy field. The gas’s adiabatic expansion is entropic, giving repulsive entropic pressure. Gas kinetic energy is converted into entropic energy gain (63%) and isoentropic work against gravity (37%) at a constant 63:37 ratio. A three-term expression of the gas’s Hubble parameter is derived and found to be exclusively dependent on its mass density. At last scattering, this model gives a Hubble constant that is 125% of the value found from the ΛCDM model. After partition of Universal mass into the cosmic web of galaxies and the intergalactic medium (IGM), expansion came mostly from the IGM, presently comprising about 84% of total Universal mass and 90% of its volume. The onset of star formation within the cosmic web increased the IGM’s kinetic energy through the action of starlight, giving free electrons as an additional repository. Many of these free electrons are suprathermal. Suprathermal energy from both electrons and protons comprises about half of the IGM’s total kinetic energy and is expressed in the ΛCDM model as “dark energy” Λ. Entropic pressure derives from thermodynamic laws not found within general relativity.

Expansion of the universal space was never directly observed. It is an unproven assumption. Measurement of the gravitational redshift proves only gravitational redshift and nothing more. Gravitational redshift is proven by the Mössbauer experiment. Claiming that gravitational redshift proves universal space expansion is false because there is no causality between gravitational redshift and hypothetical expansion. Even if universal space would expand, gravitational redshift could not be taken as proof of expansion. The Doppler effect was never observed in an expanding space and claiming that cosmological redshift is partially caused by the Doppler effect caused by the expanding of space is an unproved assumption. The discovery of CMB proves only that the entire universal space radiates CMB. CMB is not proof of the existence of the recombination period.

This letter solves an open question of paper spring risen by Yoneda (2019). Universal scaling laws of a paper spring are proposed by using both dimensional analysis and data fitting. It is found that spring force obeys power square law of spring extension, however strong nonlinear to the total twist angle. Without doing any additional works, we have successfully generalize the scaling laws for Poisson ratio 0.3 to the materials with an arbitrary Poisson's ratio with the help of dimensional analysis.

Lignin fibers typically influence the mixture performance of stone matrix asphalt (SMA), such as strength, stability, durability, noise level, rutting resistance, fatigue life, and water sensitivity. However, limited studies were conducted to analyze the influence of fibers on the percent voids in mineral aggregate in bituminous mixture (VMA) during the mixture design. This study analyzed the effect of different fibers and fiber contents on the VMA in SMA mixture design. A surface-dry condition method test and Marshall Stability test were applied on the SMA mixture with four different fibers (i.e., flocculent lignin fiber, mineral fiber, polyester fiber, blended fiber). The test results indicated that the bulk specific gravity of SMA mixtures and asphalt saturation decreased with the increasing fiber content, whilst the percent air voids in bituminous mixtures (VV), Marshall Stability and VMA increased. Mineral fiber had the most obvious impact on the bulk specific gravity of bituminous mixtures, while flocculent lignin fiber had a minimal impact. The mixture with mineral fiber and polyester fiber had significant effects on the volumetric properties, and, consequently, exhibited better VMA over the conventional SMA mixture with lignin fiber. Modified fiber content range was also provided, which will widen the utilization of mineral fiber and polyester fiber in the applications of SMA mixtures. The mixture evaluation suggested no statistically significant difference between lignin fiber and polyester fiber on the stability. The mineral fiber required a much larger fiber content to improve the mixture performance than other fibers. Overall, the results can be a reference to guide SMA mixture design.

Cultural routes are a composite set of heritage, referring to any ancient routes of human communication. As one of the key products of cultural tourism, they providing visitors with a rich cultural experience across regions. We systematically review reports and studies related to the tourism development of 38 cultural routes cases around the world, with a special focus on their distribution, typology, planning patterns and tools for cultural tourism. We summarized eight tools, there are some differences in how often these eight tools are used by the different types of routes and different planning patterns for routes tourism. The study also made an evaluation system based on the conservation principles of cultural routes to find out how different tools of tourism affect the conservation and development of the historical region. It was found that although many efforts have been made by tourism decision-makers to protect and develop cultural routes there are still many problems and challenges in the process of tourism development along cultural routes. We close the paper by making a few recommendations for decision makers and researchers concerning future routes’ tourism planning and study.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

The objective of this paper was to verify the applicability of statistical learning (SL) compared to human reasoning with respect to the Universal Thermal Climate Index (UTCI), a complex tool for the assessment of outdoor thermal stress. UTCI is an equivalent temperature index based on the 48-dimensional output of an advanced model of human thermoregulation formed by 12 variables at four consecutive 30-minute intervals, which were calculated for 105642 thermal conditions from extreme cold to extreme heat. Comparing the performance of SL algorithms to the results accomplished by an international endeavor involving more than 40 experts from 23 countries, we found that random forests and k-nearest neighbors closely predicted UTCI values, but that clustering applied after dimension reduction algorithms (principal component analysis and t-distributed stochastic neighbor embedding) were inadequate for risk assessment in relation to the UTCI stress categories. This indicates a potential supportive role for SL, as it will not (yet) fully replace the bio-meteorological expert knowledge.

Transition metal complexes have historically played a pivotal role in creating vibrant pigments utilized across artistic mediums such as ceramics, paintings, and glass mosaics. Despite their extensive historical use, our understanding of the mechanisms governing transition metal complex behavior has predominantly emerged in recent times, leaving numerous aspects of this process ripe for exploration. These complexes exhibit striking color variations under diverse conditions when employed in pigment formulations. This review utilizes a bottom-up scientific approach, spanning from microscopic to macroscopic scales, to unravel the molecular origins of the colors generated by transition metal complexes in pigments and ceramic glazes. Advanced spectroscopy techniques and computational chemistry play pivotal roles in this endeavor, highlighting the significance of understanding and utilizing analytical data effectively, with careful consideration of each technique's specific application. Furthermore, the review investigates the influence of processing conditions on color variations, providing valuable insights for artists and manufacturers aiming to enhance the precision and quality of their creations while mitigating environmental impact.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

The paper introduces a control hybrid model that is designed on the basis of OOSEM (Object-Oriented Systems Engineering Method), MDA (Model-Driven Architecture) concepts, RealTime UML/SysML (Unified Modeling Language/Systems Modeling Language), and an algorithm based on UKF (Unscented Kalman Filter). This hybrid model enables the implementation of control elements for autonomous underwater vehicles (AUVs) and can be adapted to reuse for most standard AUV platforms. To obtain this goal, the dynamic model of AUV is integrated with the following specializations of OOSEM/MDA, in which the analysis model is clarified via the use-case model definition and then combines with HA (hybrid automata) to precisely define the requirements for control. Next, the designed model is specialized via real-time UML/SysML to get the core control blocks, which describe the behaviors and structures of control parts in detail. This design model is then transformed into the model of implementation with the assistance of round-trip engineering to conveniently realize the controller of AUVs. Based on this new model, an AUV controller for low-cost turtle-shaped AUVs is implemented that performs tracking for a planar trajectory with accepted feasibility.

The integration of magnetic observatories of many countries into the Intermagnet network has provided researchers with new opportunities to investigate many geophysical processes. The joint processing of measurement evidence from magnetic observatories located in various geolocations makes it possible to better understand the dynamics of the interaction of solar plasma fluxes with the Earth's magnetosphere. For the correct interpretation of the dynamics of physical processes, the accuracy of the time reference of measurement results is of great importance. The measurement results of local observatories were transformed to a unified ecliptic coordinate system oriented towards the Sun in order to extract small variations in the magnetic field occurring before the magnetic storm commencement. Before transforming the coordinates, a constant component equal to the average daily value of the magnetic field components was removed from the results of minute-by-minute measurements. Owing to the averaging evidence from 84 magnetic observatories of the Intermagnet network, variations in the magnetic field of cosmic origin, preceding the magnetic storm commencement were detected. The correlation analysis of these variations recorded by different observatories revealed the presence of time shifts between the data series of different observatories. Only 62% of the observatories had a relative data shift within the range of ± 1 minute. Before the joint data processing in order to efficient use of data recorded with a time shift a method for correcting time shifts has proposed.

This study aims to spatially analyze the distribution characteristics of vacant homes in Asan-si, Chungcheongnam-do, and understand the differences in factors causing vacant homes by type. We use a variety of statistical methods to examine these factors and identify key influencing factors such as the number of vacant stores, changes in overall population, land use complexity, and physical characteristics of land and buildings. The findings reveal that the factors contributing to the occurrence of vacant homes vary significantly by region and property type, highlighting the need for region-specific policies. For instance, in old town areas, small lot ratios and land use complexity are significant, while in rural village, the average number of floors and land use complexity play a major role. This study underscores the diversity of factors influencing vacant homes, suggesting that policies should be tailored to the unique characteristics of different regions to effectively address this issue.

The human mandible's cancellous bone, which is characterized by its unique porosity and directional sensitivity to external forces, is crucial for sustaining biting stress. Traditional CAD models fail to fully represent bone's anisotropic structure and thus depend on simple isotropic assumptions. For our research, we use the latest versions of nTopology and Creo Parametric software to make biomimetic Voronoi lattice models that accurately reflect the complex geometry and mechanical properties of trabecular bone. The porosity of human cancellous bone is accurately modeled in this work using biomimetic Voronoi lattice models. The porosities range from 70% to 95%, which can be achieved by changing the pore sizes to 1.0 mm, 1.5 mm, 2.0 mm, and 2.5 mm. Finite element analysis (FEA) was used to examine the displacements, stresses, and strains acting on dental implants with a buttress thread, abutment, retaining screw, and biting load surface. The results show that the Voronoi model accurately depicts the complex anatomy of the trabecular bone in the human jaw, compared to standard solid block models. The ideal pore size for biomimetic Voronoi lattice trabecular bone models is 2 mm, taking into account both the von Mises stress distribution over the dental implant, screw retention, cortical bone, cancellous bone, and micromotions. This pore size displayed balanced performance by successfully matching natural bone's mechanical characteristics. Advanced finite element analysis (FEA) improves biomechanical understanding of how bones and implants interact by creating more accurate models of biological problems and dynamic loading situations. This makes biomechanical engineering better.