One of the major concerns in structural health management (SHM) is the early detection of a growing crack. Using this, future damage due to crack propagation can be mitigated or eliminated by implementing proper repair and maintenance. Acoustic Emission (AE) is a non-destructive testing (NDT) method with potential applications for locating and monitoring fatigue cracks. The research presented in this paper focuses on SHM using AE. A novel AE signal analysis approach was proposed in order to detect crack initiation and assess small crack lengths. Experimental investigation indicated that initiation of a crack could be identified through the statistical analysis of the resulting features of the AE signals. A probabilistic AE-based model for small fatigue crack sizing was developed and the uncertainties of the model were estimated. In addition, a probabilistic model validation approach was implemented to confirm accurate estimation of the results. The outcome of this research can be used to evaluate the integrity of structures under fatigue loading. The proposed approach can also be applied as an approach to manage health and assess prognosis of structures.

This paper seeks to model the crack propagation in of AAs (aluminum-alloys) 2524-T3 and 7050-T7452 subjected to fatigue loading at low temperature. Fatigue crack growth tests were performed on AAs 2524-T3 and 7050-T7452 subjected to constant-amplitude and actual random-spectra loading histories at room temperature of about 25 °C and at cryogenic temperature of -70 °C, respectively, to determine their crack growth properties and residual lives. The interaction mechanisms between cryogenic temperature and the fatigue load were deduced on the basis of the results of fractographic analysis. Temperature-dependent residual lives under actual random-spectrum load history were modeled based on a modified accumulation damage rule by accounting for the load interaction. Good correlation was achieved between the predictions and actual experiments, demonstrating the practical and effective use of the proposed method.

This study aimed to investigate the fatigue performance and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar lap joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Furthermore, the fatigue life of the 14 kV joints was one order of magnitude higher compared to the 12 kV joints. SEM observation of the fatigue fracture surface revealed the presence of typical "tire-mark" fatigue striations only in the 14 kV joint, indicating higher ductility and the ability to withstand extended plastic deformation. Notably, ultra-fine nanocrystalline Al2Cu phase, amorphous phase, and numerous dislocations hindered EBSD acquisition in the transition zone. Nevertheless, dense low-angle grain boundaries (LAGBs) and refined grains were examined at the bonding interface. This suggests that the high-velocity collision caused severe plastic deformation and led to the formation of substructures. The interfacial strength was attributed not only to the "wave-like" or "inverted hook-like" diffusion layer but also to the presence of refined grains along the interface and nanocrystalline Al2Cu in the transition zone. Furthermore, the hybrid nanocrystalline-amorphous microstructure strengthened the joint by regulating the balance between strength and ductility.

The main purpose of this work was to tests of form and size of fatigue wear of the top layer of oil gear pump wheel (3PW-BPF-24). The object of tests was operated during a determined number of hours at strictly controlled operational and environmental parameters. A microscope of focal differentiation by Alicona InfiniteFocus G4 (with Focus-Variation optical measuring technology) was used for an identification, measurement and description of noticed superficial defects, which resulted from the fatigue process of the top layer and an earlier thermochemical treatment. The work was finished with an analysis of obtained results (based on the analysis of 3D scans) and conclusions concerning about optimization of the thermal treatment. Taking into consideration the presented results (suggestions) in the technology of improving strength properties of gear wheels (of this type oil pumps) may render it possible to obtain an appropriate fatigue endurance of the top layer, i.e. a minimization of observed superficial defects.

Analysis of Fatigue Strain, Fatigue Modulus and Fatigue Damage for the modeling of concrete plays a vital role in the evolution material behaviour which is heterogeneous and anisotropic in nature. In this paper, the Level-S nonlinear fatigue strain curve, fatigue modulus curve, residual strain curve of concrete in compression, tension, flexure and torsional fatigue loading were proposed using strain life approach. The parameters such as physical meaning, the ranges, and the impact on the shape of the curve were discussed. Then, the evolution model of fatigue modulus was established based on the fatigue strain evolution model, fatigue modulus evaluation model, residual strain evaluation model, secondary strain evaluation model. The hypothesis of fatigue modulus is inversely related with the fatigue strain amplitude. The fatigue evolution of concrete damages the bond between material grains, changed the orientation of structure of molecules and affects the elastic properties resulting in the reduction of material stiffness and modulus by utilizing strain life analysis, regarding stiffness degradation and inelastic deformation by formation of microcracking, macro cracking, cracking which is heterogeneous and anisotropic in nature . This paper presents the Fatigue Strain Life Model and analyses of fatigue strain, fatigue modulus and damage parameters of concrete which is capable of predicting stiffness degradation, inelastic deformation, strength reduction under fatigue loading. Hence, the obtainable results were compared with experimental results for the validation of the proposed model.

This paper reassesses the detrimental effect on fatigue performance due to thicker sections based on extensive fatigue strength test database, taken from research program worldwide over the past half of a century in offshore oil & gas and renewable industry. The data entries in the database have been evaluated to ensure its data integrity. Statistical analyses on these S-N data are performed with or without the thickness correction at different exposure level to corrosive environment, in order to re-evaluate the suitability of current standards in regard to the thickness effect. The study has concentrated on T-joint, transverse butt welded joint and tubular joint as these are the most commonly used joint types in the offshore wind industry. The analysis indicates general agreement of fatigue strength with the thickness effects in current standard for in air conditions but great conservatism for corrosive environment.

Objective: This research was aimed to estimate the anti-fatigue effects of arecoline and elucidate its underlying mechanisms using a murine model of central fatigue precipitated by sleep deprivation (SD). Methods: Seventy-two male C57BL/6 mice were randomly allocated into six groups: a control group, a SD-induced fatigue model group, a group receiving Rhodiola Rosea capsules (2.5 mg/kg), and arecoline groups administered low, medium, and high doses (10, 20, and 40 mg/kg, respectively). Following 28 days of continuous administrations, the effects of arecoline on the mouse fatigue-related behaviors was assessed by the behavioral tests, including grip strength, rotarod performance, and weight-bearing swimming endurance. Enzyme-linked immunosorbent assays (ELISAs) were utilized to measure the levels of the relevant biochemical markers. Western blotting was employed to quantify the expression of nuclear factor erythroid 2-related factor (Nrf2), Kelch-like ECH-associated protein 1 (Keap1), heme oxygenase 1 (HO-1), sequestosome-1 (p62), and NADPH quinone oxidoreductase 1 (NQO1) in the gastrocnemius muscle. Results: Arecoline administration notably enhanced grip strength, delayed the onset of fatigue as evidenced by extended latencies in rotarod tests, and increased the duration of weight-bearing swimming in mice. In the elevated plus maze, arecoline significantly reduced both the number of entries and the total distance traveled in the open arms. Arecoline markedly decreased serum levels of creatine kinase, blood urea nitrogen, lactate dehydrogenase, triglycerides, and cholesterol, while elevated total testosterone, lactate dehydrogenase, and immunoglobulin G levels. Furthermore, it significantly increased superoxide dismutase(SOD), catalase(CAT), and glutathione peroxidase activity in the gastrocnemius muscle, reduced malondialdehyde levels, augmented hippocampal SOD and CAT activity, and elevated glycogen stores in both liver and muscle tissues. Neurotransmitter levels were significantly increased, cytokine levels were markedly reduced, and the expression of Nrf2, Keap1, NQO1, p62, and HO-1 in brain tissue was significantly upregulated. Conclusion: The current study for the first time demonstrated that arecoline has significant anti-fatigue activity, and its mechanism of action is related to elevate the levels of glucose and lipid metabolism, relieve oxidative stress damage, inhibit neuroinflammatory response, regulate neurotransmitter levels and Keap1/Nrf2/HO-1 signaling pathway. The current study provides a new insight into the potential of arecoline in prevention and improvement of fatigue.

Leaf springs are critical components for the railway vehicle safety in which they are installed. Although these components are produced in high-strength alloyed steel and designed to operate under cyclic loading conditions in the high-cyclic fatigue region, their failure is still possible to occur and hence lead to economic and human catastrophes. The aim of this document is precisely to characterise the mechanical crack growth behaviour of the 51CrV4 spring steel representative of leaf springs under cyclic conditions, that is, crack propagation in mode I. The common fatigue crack growth prediction models (Paris and Walker) considering the effect of stress ratio and parameters such as propagation threshold, critical stress intensity factor and crack closure ratio are also determined using statistical methods, which resulted in good approximations with respect to the experimental results. Lastly, the fracture surfaces under the different test conditions were analysed using SEM, with no significant differences to declare. As a result of this research work, it is expected that the developed properties and fatigue crack growth prediction models can assist design and maintenance engineers in understanding fatigue behaviour in the initiation and propagation phase of cracks in leaf springs for railway freight wagons.

It has been known for nearly over 150 years that fatigue life data exhibits a considerable amount of variability. Furthermore, statistically modeling fatigue life adequately is challenging. Different empirical approaches have been used, each of which has merit; however, none is appropriate universally. Even when a sufficiently robust database exists, the scatter in the fatigue lives may be extremely large and difficult to characterize. The complications in empirical modeling are exacerbated for long life estimation when experimental observations are rare. The purpose of this work is to review traditional and more modern empirically based methodologies for estimating the cumulative distribution functions for fatigue life, given an applied load. To assess the applicability of the methods confidence bounds will be estimated. The analyses will be performed on an historic set of data for annealed aluminum wire tested in reverse torsion fatigue. These data are available in publications. It is recommended that a time dependent distribution function that is an based on principles of reliability that can be generalized for a variety of modeling applications should be considered for fatigue life estimation.

The concept of Design Fatigue Factors (DFFs) was introduced for providing desired level of safety in structural fatigue design, often associated with damage calculated from S-N curves. Calculation of fatigue damage from S-N curves can be affected by multiple factors, e.g. types of weld class, corrosion condition, loading conditions, stress concentration on different geometries etc. Each of them can be subject to different level of uncertainties. This study intends to recalibrate the DFFs from a detailed reliability analysis by investigating the probabilistic models derived from the database of S-N curves that has been most frequently used in offshore wind industry. The results of such study indicate that the DFFs can be reduced substantially for the corrosive environmental fatigue models from current standards to the same level of target reliability.

In 2011, it was reviewed that there is a strong co-occurrence between major depression and chronic fatigue syndrome (CFS), with fatigue and physio-somatic symptoms being key symptoms of depression, and depressive symptoms appearing during the course of CFS. Moreover, the comorbidity between both conditions may in part be explained by activated immune-inflammatory pathways, including increased translocation of Gram-negative bacteria and increased levels of pro-inflammatory cytokines, such as interleukin (IL)-1. Nevertheless, the possible involvement of activated microglia in this comorbidity has remained unclear. This paper aims to review microglial disturbances in major depression, CFS and their comorbidity. A comprehensive literature search was conducted using the PubMed / MEDLINE database to identify studies that are relevant to this current review. Depressed patients present neuroinflammatory alterations, probably related to microglial activation, while animal models show that a microglial response to immune challenges including lipopolysaccharides is accompanied by depressive-like behaviors. Recent evidence from preclinical studies indicate that activated microglia have a key role in the onset of fatigue. In chronic inflammatory conditions, such as infections and senescence, microglia orchestrate an inflammatory microenvironment thereby causing fatigue. In conclusion, based on our review we may posit that shared immune-inflammatory pathways and activated microglia underpin comorbid depression and CFS and that activated microglia are the main orchestrators of this comorbidity. As such, microglial activation and neuro-inflammation may be promising targets to treat the overlapping manifestations of both depression and CFS.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

Recent works in mechanical fatigue consider that a threshold of entropy exists, the fracture fatigue entropy. The determination of this quantity is usually done considering empirical models for the mechanical power estimation. In this paper, we experimentally observe the existence of a threshold of entropy and exergy in low cycle fatigue for a flat Al-2024 specimen avoiding the use of a model, solely measuring the heat generated during a fatigue test. Results are then compared considering various hypotheses (1D heat dissipation with convection and radiation considered as heat sources, and, heat transfer from a fin with convection and radiation as boundary conditions) to an empirical mechanical model known in the literature and deviations between them are discussed.

Athletes are exposed to high-intensity loads to promote athletic performance, however without appropriate evaluation for its effects. This study investigates the effects of four types of exhaustion exercises on Heart Rate Variability (HRV) and Poincaré features as markers of central fatigue; Creatine Kinase (CK) and blood lactate concentrations ([LA-]b) as biomarkers of peripheral fatigue. To achieve this purpose, ten healthy volunteers were exposed to exhaustive exercise using isotonic-, isometric-, aerobic-, and anaerobic-fatigue protocols. HRV Poincaré features, standard deviation of instantaneous beat-to-beat R-R interval variability (SD1) and standard deviation of continuous long-term R-R interval variability (SD2) variables were collected. Central fatigue was tested through the sympathetic stress index (SS) and the sympathetic and parasympathetic index (SS/SD1). Blood samples were collected at the beginning and at the end of the exercises to determine CK and [LA-]b. The SD1 decreased in each exercise protocol, while the SS and SS/SD1 increased. [LA-]b and CK increased at the end of each protocol and correlated with SD1 and SS/SD1. HRV, CK, and [LA^-]_b are acute markers to detect, both central and peripheral fatigue; sensitive to the type, duration, and intensity of exercise, being HRV a novel noninvasive marker, simple and useful for sports coaches and athletes.

TThe aim of the work is to present a newly developed stand and methodology of accelerated tests of fatigue strength of flexible propellers and fins. The paper presents the design and concepts of the measuring elements used in the research. Test methodology and water stressing were devel-oped. The mechanical properties of the following materials were presented: Arnitel EL-550 and QUEO 8230 with the addition of PP / EVA 50/50 (polypropylene / ethylene-vinyl acetate) - in the proportion of 70/30 (QUEO 8230 / additive). The constructed test stand and a new method of fa-tigue testing of biomimetic fins made it possible to determine the number of fin movement cy-cles under a given load, which may facilitate the determination of a warranty for a newly intro-duced product. The current consumption by the fin drive and video monitoring allowed for the selection of the range of the number of movement cycles and the determination of the moment of fatigue cracks until the fin structure loses its capacity. During the analysis, the test results showed that the fins made of Arnitel EL-550 did not show changes in the measured values of the current and the force generated by the fin. For a fin made of QUEO 8230, at 35,000 cycles, there is a decrease in the current and force consumed, which indicates the initiation of fatigue damage to the fin. The performed tests can be the basis for the development of standards for the fatigue strength of flexible propellers.

The fatigue delamination damage is one of the most important fatigue failure modes of laminated composite structures. However, the developments of the theoretical framework, mathematical/physical model and numerical simulation of fatigue delamination are still challenging issues, and there is a lack of systematic classification. This article reviews the experimental phenomena of the onset and propagation stage of delamination under fatigue loading, and summarizes the commonly used phenomenological models for laminated composite structures. The research methods, general modeling formulas and development prospects of the phenomenological models are presented in detail. In the light of the analysis of finite element model (FEM) for the laminated composite structures, a number of simulation methods of fatigue delamination crack propagation damage model are carefully classified. Furthermore, within the theoretical framework of strength theory model (SM), fracture mechanics model (FM), damage mechanics model (DM) and hybrid model (HM), the complete procedure, application, capability assessment, advantages and limitations of the models are also discussed in detail. Finally, several valuable suggestions are given for the research interests, and challenging technical problems that need to be overcome on the fatigue delamination prediction of laminated composite structures in the future.

Steel structures, such as bridges, must be continuously maintained. Due to increasing trac loads, design and execution shortcomings, many steel bridges are subject to various types of damage, such as cracks. The bridges must be maintained by crack removal and re-welding the cracks. During this work, the bridge is closed for trac in order to suppress the crack ank movement during welding. As a result, trac loads on other routes are higher, which increases further damage on detour routes and subsequently additional welding work and costs on theses structures. Therefore, the aim is to provide a method that allows welding work on steel structures under running trac, respectively under cyclic loads. First, measurements at a representative steel bridge were conducted to derive gap opening parameters of amplitude and frequency for welding tests under cyclic loads. In a test setup for reproducible and comparable welding tests, specimen were welded under cyclic loads. Deep grinding of the root layer allowed defect-free welding within the range of 0.1 mm amplitude at a frequency of 2 Hz loadings. For such welds, the weld quality and the fatigue strength was comparable to the standard requirements.

In this paper, we present a new stress calculation method for flexible structures, particularly, the tensile armors, and apply it to flexible riser fatigue analysis. The method is based on a 3-dimensional curved bar theory. First, the tensile armor center line was described as a cylindrical helix curve, its bended curve length and bending migration length were derived and studied under different friction scenarios. Second, the tensile and bending stiffness was given with consideration of frictional hysteretic effect, and verified through FEA analysis results. Third, we presented the stress calculation formula for tensile armor under tension and bending load. All stress components are considered, including tensile, bending and shear stresses. Fourth, the method was benchmarked with published experimental results on a flexible prototype tension and bending tests, and comparisons showed general agreements. Fifth, the method is further applied to a 8” flexible riser for fatigue assessment and lifetime extension evaluation, and showed the flexible riser has sufficient remaining fatigue life, and is suitable to continue its service under the current operating conditions. Last, conclusions are drawn. It concluded that the presented tensile armor stress calculation method and modelling techniques are valid for flexible riser fatigue analysis. This method is time efficient, and can be implemented into other multi-scale models for riser dynamic analysis. It is also applicable to other similar helix structure stress analysis, such as wire ropes, submarine hoses, and subsea umbilicals.

Natural cellulose hydrogels have been widely used to enhance mechanical properties. However, existing natural fiber composite hydrogels are not reusable, limiting their potential applications. To address this issue, we designed and prepared a polyvinyl alcohol/glycerol /bamboo microfibril double network tough hydrogel using a simple method. The bamboo microfibril and polyvinyl alcohol form a tight and rigid network through hydrogen bonding, improving mechanical properties. The prepared polyvinyl alcohol/glycerol/bamboo microfibril double network tough hydrogel has the advantages of reusability and fatigue resistance. Furthermore, both the elastic modulus and toughness of the hydrogel increase with increasing bamboo microfibril content. We also demonstrated that the hydrogel can be recast after cyclic compression, maintaining its recyclability, stability, and certain stiffness and toughness. Our study highlights the potential of hydrogels for controllable mechanical properties, fatigue resistance and shows that polyvinyl alcohol/glycerol/bamboo microfibril hydrogel has broad value for plasticity and reuse.

This paper aims to provide an overall review of degradation, damage evolution and fatigue models in the literature of various engineering materials, mostly metals, and composites.

Reliable fatigue design rules affect the proactive identification of safety parameters in aerospace industry. Numerous fatigue crack initiation and propagation models, linear and nonlinear, have been developed for designing purposes or estimation of the remaining life of aging airplanes. Depending on the adopted assumptions, the accuracy varies for different loading histories, loading types, and materials. Semi empirical models are simple but yield significant inaccuracies. Models with better theoretical basis provide better accuracy, but implementation in real conditions is problematic. In the present work, a review of author’s recent fatigue crack initiation and propagation models based on physical mechanisms is presented and improvements are proposed. Verification of the models on test results is provided and discussed.

In Nature, it is common for living plants and non-living plant tissues to consist of materials with anisotropic multilayer and non-homogenous structure. The structure of tissues determines their self-shaping and self-folding capabilities in response to a stimulus in order to activate different functionalities. Predetermined movements are realized according to changes in environmental conditions, which trigger the fibrous anisotropic structure of the plants’ material. In this study, we present the fabrication process of low-cost anisotropic multilayer materials that are capable of realizing complex movements caused by small temperature changes (<40 ^oC). The mismatch in the thermo-mechanical properties between three or more anisotropic thin layers creates responsive materials that alter their shape owing to the developed internal stresses. Isotropic layers can perform only bending movements, whereas anisotropic multilayer materials can perform bending, twisting or complex combined modes. The movements of the material can be controlled by forming anisotropic homogenous metallic strips over an anisotropic polymer. As a result, inexpensive responsive materials can be developed to passively react to a very broad range of thermal requirements. We studied the major parameters that affect the sensitivity of the developed materials, as well as their failure modes and crack formation under thermal fatigue conditions.

The plate heat exchanger (PHE) is a component that provides heat to be transferred from hot water to domestic cold water without mixing them with high efficiency. Over the lifetime of the PHE, cyclic pressures act on the brazing points and the plates, and this may lead to fatigue failure. The fatigue behaviour of the PHE, designed by using copper-brazed 316L stainless steel, was investigated in this study. First, the fatigue tests under the load ratio R = 0.1 were performed on the Vibrophore 100 testing machine to obtain the S-N curve of the analysed brazed joint. Based on the obtained experimental results, an appropriate material model of the analysed brazed joint has been created, which was validated with numerical calculation in the framework of a program code Ansys. A validated material model was then used for the subsequent numerical analysis of PHE. In order to carry out a numerical calculation using the finite element method (FEM), a 3D model of the heat exchanger was created based on the previous scanning of PHE-geometry. Thereafter, the geometry was parameterised, which allowed us to perform parametric simulations (monitoring different responses depending on the input geometry). Numerical simulations were carried out in the framework of the Ansys software, whereby the obtained results were analysed, and the responses were appropriately characterised according to previously determined load cases.

The underlying molecular basis of Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is not well understood. Characterized by chronic, unexplained fatigue, a disabling payback following exertion (“post-exertional malaise”) and variably presenting, multi-system symptoms, ME/CFS is a complex disease which demands concerted biomedical investigation from disparate fields of expertise. ME/CFS research and patient treatment have been challenged by the lack of diagnostic biomarkers and finding these is a prominent direction of current work. Despite these challenges, modern research demonstrates a tangible biomedical basis for the disorder across many body systems. This evidence is largely comprised of disturbances to immunological and inflammatory pathways, autonomic and neurologic systems, abnormalities in muscle and mitochondrial function, shifts in metabolism, and gut physiology or gut microbiome disturbances. It is possible that these threads are together entangled as parts of an underlying molecular pathology reflecting a far-reaching homeostatic shift affecting each of these systems. Due to the variability of non-overlapping symptom presentation or precipitating events such as infection or other bodily stresses, the initiation of body-wide pathological cascades with similar outcomes stemming from different causes may be implicated in the condition. Patient stratification to account for this heterogeneity is therefore one important consideration during exploration of potential diagnostic developments.

Abstract Background Fatigue Syndrome (FS) is described as extreme exhaustion following ordinary activities. Sleep deprivation, the use of antidepressants, autoimmune illnesses, and anemia are also risk factors for FS. Symptoms of FS include headache, dizziness, and dyspnea, among others. Objective: This study focused on assessing the prevalence of fatigue syndrome (FS) and its association with depression and anxiety, among the medical students in Saudi Arabia. Methodology In this cross-sectional investigation conducted in 2023, 740 medical students participated. Data were gathered using an online survey, which encompassed four key sections: Sociodemographic details, the 11-item Chalder Fatigue Questionnaire (CFQ), the 9-item Primary Health Questionnaire (PHQ) assessing depression, and the Generalized Anxiety Disorder 7-item (GAD-7) scale. Analyses were performed by the use of SPSS version 25. Results A total of 740 students were surveyed, 417 (56.4%) satisfied the diagnostic requirements for fatigue syndrome (FS), with most of them being females. Furthermore, 234 (31.2%) and 296 (40.8%) of the participants reported having significant anxiety symptoms and depressive symptoms, respectively. FS was positively correlated with symptoms of anxiety and depression (P

Chronic Fatigue Syndrome (CFS) can be triggered by different factors and create a complex health situation. In the last decades incidence has been increasing. This situation is a clear example of how humans, viruses, and the environment are all connected. In the 90s cases related to CFS, com-plaints about a feeling of chronic fatigue, inability for everyday tasks, dull pain, cephalalgia, de-pression, anxiety, poor concentration. Clinical tests for EBV, HHV, CMV, IgG, IgM, T4 and T8 subsets were tested, along with hormones and hemogram tests. Most of the cases were women. The timeline of the medical history showed also myomas, breast lumps, premenstrual syndrome previously to CFS development. The nature of these conditions promoted the idea of a possible common link among them and CFS. Some cases also suffered from allergies, food intolerances, candidiasis, intestinal impairment, thyroid implications, endometriosis. As an initial working hypothesis, The Liver Link (TLL) was proposed in order to understand those different conditions affecting body, mind and emotional wellbeing. Considering liver implication can make a differ-ence in treatment and recovery. Low grade inflammatory conditions are related to Th2 predom-inance and liver functions. Functional disharmonies are very important because they usually still do not appear in any conventional tests. In 2002, TLL was presented as a framework to explain the concomitance of CFS and other conditions and the relationship with some viruses such as EBV, HHV, CMV, as a lecture in a congress at the University of Westminster (London). When SARS-CoV-2 outbroke, TLL helped to warn about the post-covid syndrome more likely to occur in specific individuals.

In this paper, we investigate the effects of mean stress, multiaxial loading, and residual stresses on the fatigue life of springs. We study the fatigue life of a homogeneously stressed material subjected to cyclic loading with nonzero mean stress. Traditional methods for estimating fatigue life are based on Goodman and HAIGH diagrams. The formal analytical descriptions, namely "stress-life" and "strain-life" approaches, are found to be more suitable for the numerical methods. The fatigue analysis method described above, which describes crack growth per cycle, is extended. The extensions allow consideration of the mean stress of a load cycle. Closed-form expressions for crack length versus number of cycles are derived. The complementary effects on the fatigue life of springs, which ultimately have a significant influence on the fatigue life of springs, are summarized. For the proposed unified fatigue life functions, the ranges for the stress loading factor are extended by introducing the effective stress intensity. The solution leads to the factor range for the effective stress intensity, the effective mean value of the stress intensity factor and the effective stress ratio. The developed method assumes the homogeneous stress state in the whole spring element. For the non-homogeneously loaded structural elements, the weak-link concept is applied to account for fatigue.

Little is known about how recreational triathletes prepare for an Olympic distance event. The aim of this study was to identify the training characteristics of recreational-level triathletes within the competition period and assess how their preparation for a triathlon influences their health and their levels of fatigue. During the 6 weeks prior to an Olympic distance triathlon, and the 2 weeks after, 9 recreational athletes (5 males, 4 females) completed a daily training log. Participants answered the Daily Analysis of Life Demands Questionnaire (DALDA), the Training Distress Scale (TDS), and the Alberta Swim Fatigue and Health Questionnaire weekly. The Recovery-Stress Questionnaire (REST-Q) was completed at the beginning of the study, on the day before the competition, and at the end of week 8. Training loads were calculated using session-based rating of perceived exertion (sRPE). The data from every week of training was compared to week 1 to determine how athletes’ training and health changed throughout the study. No changes in training loads, duration, or training intensity distribution were seen in the weeks leading up to the competition. Training duration was significantly reduced in week 6 (p=0.041, d = 1.58, 95% CI = 6.9, 421.9), while the number of sessions was reduced in week 6 (Z=2.32, p=0.02, ES = 0.88) and week 7 (Z = 2.31, p=0.02, ES = 0.87). Training was characterized by large weekly variations in training loads and a high training intensity. No significant changes were seen in the DALDA, TDS, or REST-Q questionnaire scores throughout the 8 weeks. Despite large spikes in training load and a high overall training intensity, these recreational-level triathletes were able to maintain their health in the 6 weeks of training prior an Olympic distance triathlon.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

Using the culture-work-health model, this study investigates the factors influencing the quality of life of maritime workers. This study conducted a survey of 320 maritime workers who have experience living and working on a ship for more than six months. This self-administered questionnaire included questions on organizational culture and support, self-efficacy, perceived fatigue, as well as the quality of work life. Organizational culture and self-efficacy were identified as factors affecting the quality of work life, while organizational support was found to have an indirect effect after passing through self-efficacy and perceived fatigue. The final model accounts for 63.1% of the variance in maritime workers’ quality of life. As such, this study shows that self-efficacy is important for the quality of life of maritime workers, having both direct and indirect effects. Moreover, organizational support may prove the primary intervention point for relieving perceived fatigue and enhancing self-efficacy, thus improving the quality of work life.

Myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) is a complex, multisystem, and profoundly debilitating condition, probably of multifactorial etiology. No effective approved drugs are currently available for its treatment. Several studies have proposed symptomatic treatment with melatonin and zinc supplementation in chronic illnesses; however, little is known about the synergistic effect of this treatment on fatigue-related symptoms in ME/CFS. The primary endpoint of the study was to assess the effect of oral melatonin plus zinc supplementation on fatigue in ME/CFS. Secondary measures included participants’ sleep disturbances, anxiety/depression, and health-related quality of life. A proof-of-concept, 16-week, randomized, placebo-controlled, double-blind trial was conducted in 50 ME/CFS patients assigned to receive either oral melatonin (1 mg) plus zinc (10 mg) supplementation (n = 24) or matching placebo (n = 26) once daily. Endpoint outcomes were evaluated at baseline and then reassessed at 8 and 16 weeks of treatment and 4 weeks after treatment cessation, using self-reported outcome measures. Treatment was safe and well-tolerated. The most relevant results were the significant reduction in the perception of physical fatigue in the active group at the final follow-up versus placebo (p < 0.05), and the significant improvement in the physical component summary at all follow-up visits in the experimental group. Our findings suggest that oral melatonin plus zinc supplementation for 16 weeks is safe and potentially effective in reducing fatigue and improving the quality of life in ME/CFS. This clinical study was registered on ClinicalTrials.gov (NCT03000777).

The aim of our study was to assess university students’ sleep quality and fatigue before and during the academic exam period and identify potential associated factors. A Web-based survey was completed by 940 students of 20 different Tertiary Institutions including demographics, sleep habits, exercise, caffeine, tobacco, alcohol use, subjective sleep quality (Pittsburgh Sleep Quality Index - PSQI) and fatigue (Fatigue severity scale – FSS) at the beginning of semester and at examination period. During exam period, PSQI (8.9 vs 6.1, p&lt;0.001) and FSS scores (36.9 vs 32.7, p&lt;0.001) were significantly elevated compared to pre-exam period. Increase of PSQI score was associated with age (β=0.111, p=0.011), presence of chronic disease (β=0.914, p=0.006), and depressive symptoms (β=0.459, p=0.001). Increase of FSS score was associated with female gender (β=1.658, p&lt;0.001), age, (β=0.198, p=0.010), increase in smoking (β=1.7, p=0.029), coffee/energy drinks consumption (β=1.988, p&lt;0.001), decreased levels of physical exercise (β=1.660, p&lt;0.001), and depressive symptoms (β=2.526, p&lt;0.001). In conclusion, our results show that sleep quality and fatigue are affected in university students during exam periods. Potential factors were identified which may lead to development of strategies for better quality of sleep, and wellbeing.

Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is a complex disease characterized by profound fatigue, post-exertional malaise (PEM), and neurocognitive dysfunction. Immune dysregulation and gastrointestinal symptoms are commonly observed in ME/CFS patients. Despite affecting approximately 0.89% of the general population, the underlying pathophysiological mechanisms remain poorly understood. This study aimed to elucidate the relationship between immunological characteristics and intestinal barrier function in ME/CFS patients. ME/CFS patients were stratified into two groups based on their immune competence. After documentation of detailed medical records, serum and plasma samples were collected for assessment of inflammatory immune mediators and biomarkers for intestinal barrier integrity by ELISA. We found reduced complement protein C4a levels in immunodeficient ME/CFS patients suggesting a sub-group specific innate immune dysregulation. ME/CFS patients without immunodeficiencies exhibit a mucosal barrier leakage, as indicated by elevated levels of Lipopolysaccharide-binding protein (LBP). Stratifying ME/CFS patients based on immune competence enabled the distinction of two subgroups with different pathophysiological patterns. The study highlights the importance of emphasizing precise patient stratification in ME/CFS, particularly in the context of defining suitable treatment strategies. Given the substantial health and socioeconomic burden associated with ME/CFS, urgent attention and research efforts are needed to define causative treatment approaches.

The fixed stroke fatigue test can not simulate the real load condition of the landing gear, and the variable stroke fatigue test has increasingly become the mainstream. A modular test device for fatigue test for aircraft landing gears was designed, the automatic control of the buffer stroke was realized with ectopic displacement control technology effectively, the horizontal loading cylinder could follow the wheel axis actively with the displacement active control technology, follow-up loading along the vertical direction was realized through constructing a polar coordinate system and making the load line automatic alignment, a split-type dummy wheel was designed to improve the loading accuracy, a booster cylinder was designed to realize the control loading of high pressure combined with the hydraulic control system. The test shows that the technical scheme meets the design requirements, and the fatigue test was completed successfully. The device for landing gear variable stroke fatigue testing can be applied to other landing gear static / fatigue tests.

In the Netherlands, the assessment of existing prestressed concrete slab-between-girder bridges showed that the thin, transversely prestressed slabs may be critical for static and fatigue punching when evaluated using the recently introduced Eurocodes. On the other hand, compressive membrane action increases the capacity of these slabs and changes the failure mode from bending to punching shear. To improve the assessment of the existing prestressed slab-between-girder bridges in the Netherlands, two 1:2 scale models of an existing bridge, the Van Brienenoord Bridge, were built in the laboratory and tested monotonically as well as under cycles of loading. The result of these experiments is: 1) the static strength of the decks, showing that compressive membrane action significantly enhances the punching capacity, and 2) the Wöhler curve of the decks, showing that compressive membrane action remains under fatigue loading. The experimental results can then be used for the assessment of the most critical existing slab-between-girder bridge. The outcome is that the bridge has sufficient punching capacity for static and fatigue loads, and thus that the existing slab-between-girder bridges in the Netherlands fulfil the code requirements for static and fatigue punching.

The use of high strength to weight ratio laminated composites is emerging in marine industry and applications as a very efficient solution for improving productivity. Nevertheless, delamination between the layers is a limiting factor for the wider application of laminated composites, as it reduces the stiffness and strengths of the structure. Interleaving nanofibrous mats between layers of composite laminates has been proved to be an effective method for improving composites delamination resistance. This paper aims to characterize the effect of interleaved nanofiber on mode I interlaminar properties and failure mechanisms when subjected to static and fatigue loadings. For this purpose, virgin and nanomodified woven laminates were subjected to Double Cantilever Beam (DCB) specimens. Static and fatigue tests were performed and the tests were monitored by acoustic emission technique. The mechanical results showed a 130% increase of delamination toughness for nanomodified specimens in the static loadings and more crack growth resistance in the fatigue loading. The AE results revealed that different type of failure mechanisms was the cause of these improvements for the modified specimens compared with the virgin ones.

This work aims at improving surface integrity and LCF life of machined Inconel 718. The correlation between the LCF life of Inconel 718 and various states of machined surface integrity is explored. In this paper, the surface integrity of Inconel 718 specimens is enhanced by low plasticity burnishing (LPB). The LCF life with different surface integrity specimens is predicted by micro-macro finite element method (FEM). Firstly, the LCF specimens with different surface integrity are machined by turning (turned specimen), polishing (matrix specimen) and LPB process (LPBed specimen). Secondly, the LCF experiment is carried out to reveal the effect of surface integrity on LCF life. Finally, the LCF micro-macro FEM model is proposed to predict the LCF of machined Inconel 718 specimens. The representative volume element (RVE) model is established based on the measured surface integrity and microstructure of Inconel 718 specimens. The effect of surface integrity on LCF life is transformed to equivalent load. The micro-macro FEM model combined with Tanaka-Mura dislocation crack initiation theory and extended finite element method (XFEM) is applied to predict the LCF life the machined specimens. The study results show that the LCF life of LPBed specimens can be improved by 90.5% and 36.1% compared with that of turned specimens and polished matrix specimens, respectively. The errors between FEM prediction results and experimental results are 13.1%, 9.2% and 12.2%, respectively. The proposed micro-macro FEM model could be utilized to predict the LCF life of Inconel 718 with different surface integrity, and further to apply the LCF life prediction in industry.

Post-viral fatigue syndrome (PVFS) encompasses a wide range of complex neuroimmune disorders of unknown cause characterized by disabling post-exertional fatigue, myalgia and joint pain, cognitive impairments, unrefreshing sleep, autonomic dysfunction, and neuropsychiatric symptoms. It includes myalgic encephalomyelitis, also known as chronic fatigue syndrome (ME/CFS), fibromyalgia (FM), and more recently post-COVID-19 condition (Long COVID). To date, there are no definitive clinical case criteria and no FDA-approved pharmacological therapies for PVFS. Given the current lack of effective treatments, there is a need to develop novel therapeutic strategies for these disorders. Mitochondria, the cellular organelles responsible for tissue energy production, have recently garnered attention in research into PVFS due to their crucial role in cellular bioenergetic metabolism in these conditions. Accumulating literature has identified a link between mitochondrial dysfunction and low-grade systemic inflammation in ME/CFS, FM, and Long COVID. To address this issue, this article aimed to critically review the evidence relating to mitochondrial dysfunction in the pathogenesis of these disorders; in particular, to evaluate the effectiveness of coenzyme Q10 supplementation on chronic fatigue and pain symptoms as a novel therapeutic strategy for the treatment of PVFS.

Although the Orthotropic steel decks (OSDs) have been widely used in the construction of long-span bridges, there are frequently reported fatigue cracks after years of operation, and the bridge deck overlay also presents severe damage due to OSD crack-induced stiffness reduction. The ultra-high performance concrete (UHPC), recognized as the most innovative cementitious composites and the next generation of high-performance materials, shows high strength, ductility, toughness and well performance on durability. After its first application to the OSD bridge in early 2000s, the orthotropic Steel-UHPC composite deck has been comprehensively studied worldwide. This review will summarize some important studies and findings on behavior and fatigue performance of orthotropic steel-UHPC composite deck. The existing studies and engineering application indicate that such deck system presents good bending behavior and high fatigue performance. The failure mode of shear studs in UHPC layer is dominated by shear fractures. The cracking of UHPC layer shall consider the superposition effect of stress from both the whole bridge structure and local decks. While some reasonable structural details in the traditional OSD may not work for the orthotropic steel-UHPC composite deck. It is recommended to evaluate the stress behavior and structural parameters, as well as fatigue life by conducting the field test under in-service traffic conditions.

A Myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) is a debilitating chronic disease of unknown aetiology under growing interest now in view of the increasingly recognized post-COVID syndrome as a new entity with similar clinical presentation. We performed the first cross-sectional study of ME/CFS in community population in Russia and then described and compared some clinical and pathophysiological characteristics of ME/CFS and post-COVID syndrome as neuroimmune disorders. Of the cohort of 76 individuals who suggested themselves suffering from ME/CFS 56 subsequently were confirmed as having CFS/ME according to ≥1 of the 4 most commonly used case definition. Of the cohort of 14 individuals with post-COVID-19 syndrome 14 met diagnostic criteria for ME/CFS. The prevalence of clinically expressed and subclinical anxiety and depression in ME / CFS and post-COVID ME/CFS did not differ significantly from that in healthy individuals. Severity of anxiety / depressive symptoms did not correlate with the severity of fatigue neigther in ME / CFS nor in post-COVID ME/CFS, but the positive correlation was found between the severity of fatigue and 20 other symptoms of ME / CFS related to the domains of “post-exertional exhaustion”, “immune dysfunction”, “sleep disturbances”, "dysfunction of the autonomic nervous system", "neurological sensory / motor disorders" and "pain syndromes". Immunological abnormalities were identified in 12/12 patients with ME / CFS according to the results of laboratory testing. The prevalence of postural orthostatic tachycardia assessed by the active standing test was 37.5% in ME / CFS and 75.0% in post-COVID ME/CFS (the latter was higher than in healthy controls, p = 0.02) There was a more pronounced increase in heart rate starting from the 6th minute of the test in post-COVID ME/CFS compared with the control group. Assessment of the functional characteristics of microcirculation by laser doppler flowmetry revealed obvious and very similar changes in ME/CFS and post-COVID ME/CFS compared to the healthy controls. The identified pattern corresponded to the hyperemic form of microcirculation disorders, usually observed in acute inflammatory processes or in deficiency of systemic vasoconstriction influences.

This study explored the development of neuromuscular fatigue responses during progressive cycling exercise. The sample comprised 32 participants aged 22.0 ± 0.54 years who were assigned into three groups: endurance-trained group (END, triathletes, n = 10), strength-trained group (STR, body-builders, n = 10), and control group (CON, recreationally active students, n = 12). The incremental cycling exercise was performed using a progressive protocol starting with a 3 min resting measurement and then 50 W workload with subsequent constant increments of 50 W every 3 minutes until 200 W. Surface electromyography (SEMG) of rectus femoris muscles was recorded during the final 30 s of each of the four workloads. During the final 15 s of each workload, participants rated their overall perception of effort using the 20-point RPE scale. Post-hoc Tukey’s HSD testing showed significant differences between END and STR groups in MF and MPF across all workloads (p < 0.001 and p < 0.01, respectively). Athletes from END group had significantly lower AEMG responses than those from STR (p = 0.0093) and CON group (p = 0.0006). Increasing RPE points from 50 to 200 W were significantly higher in STR than in END group (p < 0.001). In conclusion, there is a significant variation in neuromuscular fatigue profiles between athletes with different training backgrounds when a cycling exercise is applied. The approximately linear trend of the SEMG and RPE values of both groups of athletes with increasing workload support the increased skeletal muscle recruitment with perceived exertion or fatiguing effect.

The fatigue life of welded joints under cyclic loading is a complex process that can be roughly divided into fatigue crack initiation, crack propagation and final fracture. Usually, these phases are evaluated separately. Several methods are available to estimate the extent of the different phases in welded components, such as stress-based fatigue concepts for crack initiation or linear elastic fracture mechanics for crack propagation; however, distinguishing these phases in welded components is a complex procedure and often relies on assumptions such as transition crack sizes. The objective of this study is to investigate the relationship between fatigue crack initiation and propagation in welded joints using artificially notched specimens with welded joints characteristics of different notch acuity (different radii and opening angle). The experiments show that the investigated relationship basically depends on the notch acuity, the load level and the stress ratio.

Background: Depending on the phase of the menstrual cycle the athlete is in, some kinetic, physiological and fatigue variables will show differences. The aim of this study is to analyze whether there are changes in these variables over the course of the menstrual cycle. Methods: Eight regular female runners and triathletes performed a maximal treadmill test, as well as a submaximal test (6’ stages at 50%, 60% and 80% of maximal aerobic speed) in each of the phases of the menstrual cycle: bleeding phase (day 2.4 ± 0.7), follicular phase (day 10.4 ± 2.2) and luteal phase (day 21.8 ± 2.1). Running dynamics were measured (using RunScribe) at the end of each test, as were lactate concentration, heart rate and fatigue (evaluated on a scale of 0 to 5). Results: Higher shock (G) values were recorded in the bleeding phase and higher vertical spring stiffness (kN/m) in the follicular phase. The phase of the menstrual cycle had a significant effect on average and peak heart rate, which was significantly higher in the follicular phase. Conclusions: Higher vertical spring stiffness was observed in the follicular phase, as well as higher peak and average heart rate.

Crohn's disease (CD) is a chronic, relapsing disorder belonging to inflammatory bowel diseases (IBD). It is manifested by relapsing transmural inflammation found in any segment of the gastrointestinal tract. Chronic fatigue is a common and underrecognized symptom of CD, which prevalence is much higher in the population of CD patients as compared to healthy population. It stems from an intricate web of interactions between various risk factors, and its pathophysiology is still not fully understood. Implementation of routine screening and holistic, multidisciplinary approach involving psychological support may be crucial in management of CD patients with chronic fatigue. There is currently no single intervention aimed at decreasing fatigue alone, and its treatment is especially difficult in patients with fatigue persisting despite clinical and endoscopic remission. Extensive research is still needed in order to be able to predict, prevent, identify and ultimately treat fatigue associated with CD. The aim of this review is to summarize the knowledge on the etiology, diagnosis, and treatment of chronic fatigue in CD patients.

Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is a devastating illness whose biomedical basis is now beginning to be elucidated. We reported previously that, after recovery from frozen storage, lymphocytes (peripheral blood monocytic cells, PBMCs) from ME/CFS patients die faster in culture medium than those from healthy controls. We also found that lymphoblastoid cell lines (lymphoblasts) derived from these PBMCs exhibit multiple abnormalities in mitochondrial respiratory function and signalling activity by the cellular stress-sensing kinase TORC1. These differences were correlated with disease severity, as measured by the Richardson and Lidbury Weighted Standing Test. The clarity of the differences between these cells derived from ME/CFS patient blood and those from healthy controls suggested that they may provide useful biomarkers for ME/CFS. Here we report a preliminary investigation into that possibility using a variety of analytical classification tools, including linear discriminant analysis, logistic regression and Receiver Operating Characteristic (ROC) curve analysis. We found that results from three different tests, lymphocyte death rate, mitochondrial respiratory function and TORC1 activity could each individually serve as biomarker with better than 90% sensitivity but only modest specificity vís a vís healthy controls. However, in combination they provided a cell-based biomarker with sensitivity and specificity approaching 100% in our sample. This level of sensitivity and specificity was almost equalled by a suggested protocol in which the frozen lymphocyte death rate was used as a highly sensitive test to triage positive samples to the more time consuming and expensive tests measuring lymphoblast respiratory function and TORC1 activity. This protocol provides a promising biomarker that could assist in more rapid and accurate diagnosis of ME/CFS.

In this paper, the fatigue response of Fused Filament Fabrication (FFF) Acrylonitrile butadiene styrene (ABS) parts is studied. Different building parameters (layer height, nozzle diameter, infill density, and printing speed) were chosen to study their influence on the lifespan of cylindrical specimens according to a design of experiments (DOE) using the Taguchi methodology. The same DOE was applied on two different specimen sets using two different infill patterns: rectilinear and honeycomb. The results show that infill density is the most important parameter for both studied patterns. The specimens manufactured with the honeycomb pattern show longer lifespans. The best parameter set associated to that infill was chosen for a second experimental phase, in which the specimens were tested under different maximum bending stresses to construct the Wöhler curve associated to this 3D printing configuration. The results of this study are useful to design and manufacture ABS end-use parts that are expected to work under oscillating periodic loads.

Plasma treatment of soft polymers is the promising technique to improve biomedical properties. The response to the deformation of such materials is not yet clear. Soft elastic polyurethane treated with plasma immersion ion implantation is subjected to fatigue uniaxial loading (50000 cycles, frequency – 1 Hz, strain amplitude – 10, 20, 40%). The influence of the strain amplitude and the plasma treatment regime on damage character is discussed. Surface defects are studied in unloaded and stretched states of the material. As a result of fatigue loading, transverse cracks (with closed overlapping edges as well as with open edges deeply propagating into the polymer) and longitudinal folds which are break and bend inward, appear on the surface. Hard edges of cracks cut the soft polymer which is squeezed from the bulk to the surface.

This study investigates the effects of ambient illumination and negatively polarized text color on visual fatigue, exploring the issue of visual fatigue when using visual display terminals in low-illumination environments. The research methodology utilized an experimental design to collect data on changes in pupil accommodation and blink rate through an eye tracker. Partici-pants completed a reading task while exposed to various text colors and ambient light conditions to evaluate visual fatigue and cognitive performance. The study's findings suggest that text color significantly affects visual fatigue, with red text causing the highest level of visual fatigue and yellow text causing the lowest level of visual fatigue. Improvements in ambient lighting reduce visual fatigue, but the degree of improvement varies depending on the text color. Additionally, cognitive performance is better when using yellow and white text but worse when using red text. Yellow text is the most effective choice for reducing visual fatigue under negative polarity. In-creasing ambient lighting can also improve visual fatigue in low-illumination conditions. These findings will offer valuable guidance for designing visual terminal device interfaces, especially for low-illumination or night environments, to minimize visual fatigue and improve the user ex-perience.

Thermoplastic composites are continuously replacing thermosetting composites in lightweight structures. However, the accomplished work on the fatigue behavior of thermoplastics is quite limited. In the present work, we propose a numerical modeling approach for simulating fatigue delamination growth and predicting the residual tensile strength of quasi-isotropic TC 1225 LM PAEK thermoplastic coupons. The approach is supported and validated by tension and fatigue (non-interrupted and interrupted) tests. Fatigue delamination growth is simulated using a mixed-mode fatigue crack growth model, which is based on the cohesive zone modeling method. All interfaces between the thermoplastic plies were modelled using cohesive elements. Quasi-static tension analyses on pristine and fatigued coupons were performed using a progressive damage model implementing a set of Hashin-type strain-based failure criteria and a damage mechanics-based material property degradation module. Using the fatigue model, delamination growth was predicted as a function of number of cycles at all interfaces. The results agree well with C-scan images taken on fatigued coupons during interruptions of fatigue tests. An unequal and unsymmetric delamination growth was predicted due to the quasi-isotropic lay-up. Moreover, the combined models capture the decrease in the residual tensile strength of the coupons. In the quasi-static tension analysis of the fatigued coupons, the driving failure mechanisms are the fast propagation of the pre-existing delamination and the severe matrix cracking.

Background There is a considerable overlap between clinical presentation of post-COVID-19 condition (PCC) and myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) . Many of their common symptoms can be linked to dysregulation of the autonomic nervous system (dysautonomia). This study aimed to objectively assess autonomic function in patients with PCC and in patients with ME/CFS whose disease was not related to COVID-19. Methods Synchronous recordings of an electrocardiogram, continuous dynamics of blood pressure in the digital artery using the Penaz method and ultrasound pneumotachography with the spirography function were obtained with spiroarteriocardiorhythmography method in 34 patients diagnosed with ME/CFS, in whom the onset of the disease was not associated with COVID-19, 29 patients meeting PCC definition and 32 healthy controls. Heart rate variability (HRV), systolic and diastolic blood pressure variability (RV), respiration variability were assessed at rest and in tests with fixed respiratory rates. At rest, indicators of baroreflex regulation were additionally determined (baroreflex effectiveness index and baroreflex sensitivity). Results The total power, power of very low frequency, low-frequency and high-frequency of RR interval variability at rest as well as baroreflex effectiveness index in up-ramps of arterial blood pressure and baroreflex sensitivity were significantly lower both in PCC and ME/CFS patients compared to HC. Several diagnostic prediction models for ME/CFS were developed based on HRV parameters. During slow breathing HRV parameters return to normal in PCC, but not in ME/CFS. Correlation analysis revealed a close relationship of HRV, RV parameters and baroreflex sensitivity with fatigue, but not with HADS depressive/anxiety symptoms in ME/CFS and PCC. Conclusion A similar pattern of HRV and baroreflex failure with signs of a pathological acceleration of age-dependant dysautonomia was identified in ME/CFS and PCC. The clinical, diagnostic and therapeutic implications of these findings are discussed, in light of previously described relationship between inflammation, vascular pathology, atherosclerotic cardiovascular disease and autonomic dysfunction.

This paper discusses the theoretical and experimental correlations between fatigue and static strength statistical distributions. We use a two-parameter residual strength model that obeys the qualitative Strenght-Life Equal-Rank (SLERA) assumption for guidance. The modeling approach consists of recovering the model's parameters by best fitting the constant amplitude (CA) fatigue data at a given stress ratio, R, and the experimental Weibull parameters of the static strength distribution function. Once the model's parameters are fixed, its capabilities, potential, and limits are discussed by comparing its predictions with residual strength and fatigue data obtained at different stress ratios, R. Moreover, from a preliminary analysis, the theoretical extension of the model's capabilities to variable amplitude loadings is conceptualized. The application of Miner's rule is also discussed and compared with a new damage rule to analyze the fatigue responses under variable amplitude loadings.

This article presents a method that uses a semi-automatic algorithm for the detection and analysis of microcracks in steel test specimens using binarized image analysis. It obtains the length along the crack path in contrast to previous methods that have obtained linear length, thereby achieving a closer approximation to its actual value. Additionally, this method automatically calculates the COD and COA parameters with measurement deviations in micrometres, thus providing greater precision than previous methods proposed to date.

A model to rationalize the effects of test temperature and microstructural variables on the creep crack growth (CCG) and creep-fatigue crack growth (CFCG) rates in ferritic steels is described. The model predicts that as the average spacing between grain boundary particles that initiate creep cavities decrease, the CCG and CFCG rates increase. Further, CCG data at several temperatures collapse into a single trend when a temperature compensated CCG rate derived from the model is used. CCG and CFCG behavior measured at different temperatures is used to assess the effects of variables such as differences between basemetal (BM), weldmetal (WM) and the heat-affected zone (HAZ) regions. The model is demonstrated for Grade 22 and Grade 91 steels using data from literature. It is shown that differences between the CCG behavior of Grade 22 steel in new and ex-service conditions are negligible in the BM and WM regions but not in the HAZ region. The CCG behavior of Grade 91 steels can be separated into creep-ductile and creep-brittle regions. The creep-brittle tendency is linked to the presence of excess trace element concentrations in the material chemistry. Significant differences found in the CCG rates between BM and the WM and HAZ regions of Grade 91 steel were explained.

The formation and propagation of cracks occurs through irreversible dislocation movements at notches, material defects and grain boundaries. Since this process is partly thermally controlled, the resistance to dislocation movements at low temperatures increases. This slows both fatigue initiation and fatigue crack propagation. From recent experimental data, it can be seen that fatigue crack growth is accelerated below the fatigue transition temperature (FTT) that correlates with the ductile-brittle transition temperature (DBTT) found by well-known fracture mechanics tests, i.e., Charpy impact, fracture toughness, and CTOD. Hence, this study investigates the relation between FTT and DBTT in S500 high-strength steel base material and welded joints at low temperatures using fatigue crack growth, fracture toughness tests as well as scanning electron microscopy. From the tests, an almost constant decrease in fatigue crack propagation rate is determined with decreasing test temperature even below the DBTT.

Fatigue loading is critical to fibre reinforced polymer composites due to their anisotropic and heterogenous nature. This study investigated the tensile fatigue behaviour of polyester and vinyl ester based GFRP laminates to understand the critical aspects of failure mode and fatigue life under cyclic loading. GFRP laminates with two different resin systems (polyester and vinyl ester), two different stress ratios (0.1 and 0.5) and two different environmental conditions (air and water) were investigated at an applied stress of 80%, 60% and 40% of the ultimate capacity. Based on the investigated parameters (i.e., resin types, stress ratio, environmental conditioning and maximum applied stress), a fatigue model was proposed. Results show that the resin system plays a great role in fatigue failure mode while the stress ratio and environmental condition significantly affect the tensile fatigue life of GFRP laminates. The types of resin used in GFRP laminates and environmental conditions as input parameter in the proposed fatigue model is a unique contribution.

We asked whether the level of peripheral fatigue would differ when three consecutive exercise trials were completed to task failure, and whether there would be delayed recovery in maximal voluntary contraction (MVC) force, neuromuscular activation and peripheral fatigue following task failure. Ten trained sport students performed three consecutive knee extension isometric trials (T1, T2, T3) to task failure without breaks between trials. T1 and T2 consisted of repeated 5-s contractions followed by 5-s rest. In T1, contractions were performed at a target force at 60% pre-exercise MVC. In T2, all contractions were MVCs, and task failure occurred at 50% MVC. T3 was a sustained MVC performed until force fell below 15% MVC. Evoked force responses to supramaximal electrical femoral nerve stimulation were recorded to assess peripheral fatigue. Electromyography signals were normalized to M-wave amplitude to assess neuromuscular activation. Lower levels of evoked peak forces were observed at T3 compared to T2 and T1. Within 5 s of task failure in T3, MVC force and neuromuscular activation recovered substantially without any recovery in evoked peak force. Neuromuscular activation 5-10 s after T3 was unchanged from pre-exercise values, but evoked peak forces were substantially reduced. These results challenge the existence of a critical peripheral fatigue threshold that reduces neuromuscular activation. Since neuromuscular activation changed independently of any change in evoked peak force, immediate recovery in force production after exercise is due to increased central recruitment and not to peripheral mechanisms.

This study investigated the mechanical properties and fatigue behavior of FH36 steel plate rolled in different directions. By adopting a sequential rolling process in the rolling direction (RD) and transverse direction (TD), the differences in properties between RD and TD were eliminated, resulting in nearly identical tensile properties. The steel plate exhibited a yield strength of approximately 420 MPa, a tensile strength of approximately 506 MPa, and an elongation of approximately 25%. Fatigue tests conducted at room temperature and -60℃ showed a fatigue limit of the maximum stress of 488 MPa at room temperature and 500 MPa at -60℃, indicating improved low-temperature fatigue performance. The fracture surfaces displayed distinct characteristics, such as oblique shearing fractures for high-cycle fatigue and cup-cone shape fractures for low-cycle fatigue. The fatigue source zone were both on the surface of the specimens. As the maximum stress increased, the area of the crack propagation zone for high-cycle fatigue decreased, while the area of the final fracture zone, the number of dimples and the proportion of the LAGBs increased.

Interior permanent magnet motors (IPMSMs) are extensively used as traction motors today because of their exceptional torque and power density, and wide constant power operating range. Under real-world usage, an IPMSM rotor undergoes varying electromagnetic, thermal, and mechanical loads. Under such conditions, fatigue life-based design criteria should be utilized over stress-based design criteria to ensure the structural integrity of the rotor. Moreover, the driving dynamics can change the rotor temperature continuously, which affects the electromagnetic, mechanical, and fatigue properties of rotor material. This paper proposes a robust thermo-mechanical rotor fatigue simulation workflow considering the significant loads acting on an IPMSM rotor and the temperature variation throughout a drive cycle. It discusses an accelerated fatigue life estimation approach based on peak valley extraction to reduce the simulation time significantly for stress and fatigue analysis. Then, it presents a method for stress-life curve generation for a variable loading. It also presents a sensitivity study with a median S-N curve, and a 90%-reliability 95%-confidence (R90C95) S-N curve.

Most of the damage to Vleg cars was caused by material fatigue. The objectives of the fatigue analysis on Xenia 2011 car wheels with the Finite Element Method using Solidworks are: 1) Knowing the fatigue analysis process on car wheels, 2) Knowing the results of the fatigue analysis on car wheels. The research method used is the Finite Element Method (FEM) method; the re-search steps include model data retrieval from the Wheel code, 3D model creation process, static simulation process according to SAE J 328 standard, mesh variations, fatigue simulation, and finally, standardization of results fatigue simulation regarding the SAE J 328 standard. The re-sults of the fatigue analysis on the Xenia 2011 car wheels obtained an age of 1000,000 cycles when compared with the minimum average of SAE J 328 of 600,000 cycles, this product design is clas-sified as a high cycle, which means it will experience a prolonged failure, and this design has a maximum alternating stress value of 627.4702 MPa, a strain of 0.007105, a displacement of 7.148 mm and a SOF of 0.087890 with a load factor used of 2.5, so overall this Xenia car can be loaded with a load of 1775 kg, if it is more than that, then Wheels will experience cracking.

Most of the research of mental fatigue evaluation mainly concentrated on some indexes that require sophisticate and large instruments which make the detection of mental fatigue cumbersome, time-consuming, and difficult to apply on a large scale. A quick and sensitive mental fatigue detection index is necessary so that mental workers can be alerted in time and take corresponding countermeasures. But to date, no studies have compared the sensitivity of common objective evaluation indexes. To solve these problems this study recruited 56 human subjects. These subjects were evaluated using six fatigue indexes: the Stanford sleepiness scale, digital span, digital decoding, short-term memory, critical flicker fusion frequency (CFF), and speed perception deviation. The results of fatigue tests before and after mental fatigue were compared, and a one-way analysis of variance (ANOVA) was performed on the speed perception deviation. The result indicated the significance of this index. Considering individual differences, the relative fatigue index (RFI) was proposed to compare the sensitivity of the indexes. The results showed that when the self-rated fatigue grade changed from non-fatigue to mild fatigue, the ranges of RFI values for digital span, digital decoding, short-term memory and CFF were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. Correspondingly, when the self-rated fatigue grade changed from non-fatigue to severe fatigue, the ranges of RFI values for the above indexes were 0.175–0.258, 0.194–0.316, 0.068–0.139, and 0.055–0.075, respectively. These results suggest that the sensitivity of the digital decoding, digital span, short-term memory, and CFF decreased sequentially when the self-evaluated fatigue grade changed from no fatigue to mild or severe fatigue. The RFI individuality of the speed perception deviation is highly variable and is not suitable as an evaluation index. In mental fatigue testing, digital decoding testing can provide faster, more convenient, and more accurate results.

Medium-carbon steel is commonly used for the rail, wire ropes, tire cord, cold heading, forging steels, cold finished steel bars, machinable steel and so on. Its fatigue behavior analysis and fatigue life estimation play an important role in the machinery industry. In this paper, the estimation of fatigue life of medium-carbon steel with different surface roughness using established S-N and P-S-N curves is presented. To estimate the fatigue life, the effect of the average surface roughness on the fatigue life of medium-carbon steel has been investigated using 75 fatigue tests in three groups with average surface roughness (Ra): 0.4μm, 0.8μm, and 1.6μm respectively. S-N curves and P-S-N curves have been established based on the fatigue tests. The fatigue life of medium-carbon steel is then estimated based on Tanaka-Mura crack initiation life model, the crack propagation life model using Paris law, and material constants of the S-N curves. 6 more fatigue tests have been conducted to validate the presented fatigue life estimation formulation. The experimental results have shown that the presented model could estimate well the mean fatigue life of medium-carbon steel with different surface roughness

Ti17 alloy is mainly used to manufacture aero-engine discs due to its excellent properties such as high strength, toughness and hardenability. It is often subjected to creep-fatigue cyclic loading in service environments. Shakedown theory describes the state in which the accumulated plastic strain of the material stabilizes after several cycles of cyclic loading, without affecting its initial function and leading to failure. This theory includes three behaviors: elastic shakedown, plastic shakedown, and ratcheting. In this paper, the creep-fatigue tests (CF) were conducted on Ti17 alloy at 300℃ to study its shakedown behavior under creep-fatigue cyclic loading. Based on the plasticity-creep superposition model, a theory model that accurately describes the shakedown behavior of Ti17 alloy was constructed, and ABAQUS finite element software was used to validate the accuracy of the model. TEM analysis was performed to observe the micro-mechanisms of shakedown in Ti17 alloy. The results reveal that the Ti17 alloy specimens exhibit plastic shakedown behavior after three cycles of creep-fatigue loading. The established finite element model can effectively predict the plastic shakedown process of Ti17 alloy, with a relative error between the experimental and simulation results within 4%. TEM results reveal that anelastic recovery controlled by dislocation bending and back stress hardening caused by inhomogeneous deformation are the main mechanisms for the plastic shakedown behavior of Ti17 alloy.

This study investigates the power production and blade fatigue of a three-turbine array subjected to active yaw control (AYC) in full-wake and partial-wake configurations. A framework of two-way coupled large-eddy simulation (LES) and aeroelastic blade simulation is applied to simulate the atmospheric boundary-layer (ABL) flow through the turbine array and the structural responses of the turbine blades. Mean power outputs and blade fatigue loads are extracted from the simulation results. By exploring the feasible AYC decision space, we find that (a) in the full-wake configuration, the local power-optimal AYC strategy with positive yaw angles endures less flapwise blade fatigue and more edgewise blade fatigue than the global power-optimal strategy; (b) in the partial-wake configuration, applying positive AYC in certain inflow wind directions achieves higher optimal power gains than that in the full-wake scenario and reduces the blade fatigue from the non-yawed benchmark. Through a theoretical analysis based on the blade element momentum theory, we reveal that the aforementioned differences in flapwise blade fatigue between the positively and negatively yawed turbine are due to the differences in the azimuthal distributions of the local relative velocity on blade sections, resulting from the combined effects of vertical wind shear and blade rotation. Furthermore, the difference in the blade force between the positively and negatively yawed front-row turbine induces different wake velocity and turbulence distributions, causing different fatigue loads on the downwind turbine exposed to the wake.

(1) Background: Recent studies provide some evidence for the contribution of antibody-mediated autoimmune mechanisms to the nature of fibromyalgia (FM) and myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS). Much attention was paid to the autoantibodies (AAb) targeting G protein-coupled receptors as natural components of the immune system. However, natural AAb network is much more extensive, and has not been previously investigated in these disorders; (2) Methods: The enzyme immunoassays ELI-Viscero-Test and ELI-Neuro-Test were used to determine changes in serum content of a 33 natural AAb to neural, organ-specific and non-tissue-specific autoantigens a) in 11 FM patients with comorbid ME/CFS; b) in 11 ME/CFS patients without FM; c) in 11 healthy controls. Individual autoantibody profiles and their correlation with some clinical symptoms were analyzed. (3) Results: both patients with ME/CFS and ME/CFS+FM were characterized by more frequent and pronounced deviations in the immunoreactivity to GABA-receptors than healthy controls. Although the level of other natural AAb did not differ between study groups, AAb correlation signatures were changing in patients compared to healthy controls. Both in patients and healthy controls the level of natural AAb to various neural and tissue-specific antigens correlated with the severity of fatigue, bodily pain, depression, anxiety, physical and mental-health related quality of life. Notably, that widely different correlation patterns were observed between study groups. (4) Conclusions: Findings from this pilot study provide some evidence that the homeostasis of autoimmune relationships, which are possibly a physiological part of our immune system, may break down in FM and ME/CFS. The correlation of disease-induced perturbations in individual AAb profiles with some clinical symptoms may arise from the immune system's ability to reflect qualitative and quantitative changes in antigenic composition of the body.

The fatigue life of concrete is affected by many interwoven factors whose effect is nonlinear. Be-cause of its unique self-learning ability and strong generalization capability, the Bayesian regu-larized backpropagation neural network (BR-BPNN) is proposed to predict concrete behavior in tensile fatigue. The optimal model was determined through various combinations of network parameters. The average relative impact value (ARIV) was constructed to evaluate the correla-tion between fatigue life and its influencing parameters (maximum stress level Smax, stress ratio R, static strength f, failure probability P). ARIV results were also compared with other factor as-sessment methods (weight equation and multiple linear regression analyses). Using BR-BPNN, S-N curves were then obtained for the combinations of R=0.1, 0.2, 0.5; f=5, 6, 7MPa; P=5%, 50%, 95%. The tensile fatigue results under different testing conditions were finally compared for compatibility. It was concluded that Smax has the most significant negative effect on fatigue life; the degree of influence of R, P, and f, which positively correlate with fatigue life, decreases suc-cessively. ARIV is confirmed as a feasible way to analyze the importance of parameters and could be recommended for future applications. The tensile fatigue performance of plain concrete under different stress states (flexural tension, axial tension, splitting tension) does not differ sig-nificantly. Besides utilizing the valuable fatigue test data scattered in the literature, insights gained from this work could provide a reference for subsequent fatigue test program design and fatigue evaluation.

Aim: To determine whether an AI model and single sensor measuring acceleration and ECG could model cognitive and physical fatigue for a self-paced trail run. Methods: A field-based protocol of continuous fatigue repeated hourly induced physical (~45 minutes) and cognitive (~10 minutes) fatigue on one healthy participant. Physical load was a 3.8 km, 200 m vertical gain, trail run with acceleration and electrocardiogram (ECG) data collected using a single sensor. Cognitive load was a Multi Attribute Test Battery (MATB) and separate assessment battery including the Finger Tap Test (FTT), Stroop, Trail Making A and B, Spatial Memory, Paced Visual Serial Addition Test (PVSAT), and a vertical jump. A fatigue prediction model was implemented using a Convolutional Neural Network (CNN). Results: When the fatigue test battery results were compared for sensitivity to the protocol load, FTT right hand (R2 0.71) and Jump Height (R2 0.78) were the most sensitive while the other tests were less sensitive (R2 values Stroop 0.49, Trail Making A 0.29, Trail Making B 0.05, PVSAT 0.03, spatial memory 0.003). Best prediction results were achieved with a rolling average of 200 predictions (102.4 s), during set activity types, mean absolute error for ‘walk up’ (MAE200 12.5%) and range of absolute error for ‘run down‘ (RAE200 16.7%). Conclusion: We were able to measure cognitive and physical fatigue using a single wearable sensor during a practical field protocol including contextual factors in conjunction with a neural network model. This research has practical application to fatigue research in the field.

The application of instrumented indentation to assess material properties like Young’s modulus and micro-hardness has become a standard method. In recent developments, indentation experiments and simulations have been combined to inverse methods, from which further material parameters as yield strength, work hardening rate, and tensile strength can be determined. In this work, an inverse method is introduced by which material parameters for cyclic plasticity, i.e. kinematic hardening parameters, can be determined. To accomplish this, cyclic Vickers indentation experiments are combined with finite element simulations of the indentation with unknown material properties, which are then determined by inverse analysis. To validate the proposed method, these parameters are subsequently applied to predict the uniaxial stress-strain response of a material with success. The method has been validated successfully for a quenched and tempered martensitic steel and for technically pure copper, where an excellent agreement between measured and predicted cyclic stress-strain-curves has been achieved. Hence, the proposed inverse method based on cyclic nanoindentation, as a quasi-non-destructive method, could complement or even substitute the resource-intensive conventional fatigue testing in the future for some applications.

This paper aims to analyse the mechanical properties response of polylactic acid (PLA) parts manufactured through fused filament fabrication. The influence of six manufacturing factors (layer height, filament width, fill density, layer orientation, printing velocity, and infill pattern) on the flexural resistance of PLA specimens is studied through an L27 Taguchi experimental array. Different geometries have been tested on a four-point bending machine and on a rotating bending machine. From the first experimental phase, an optimal set of parameters deriving in the highest flexural resistance have been determined. Results show that layer orientation is the most influential parameter, followed by layer height, filament width, and printing velocity, whereas the fill density and infill pattern show no significant influence. Finally, the fatigue fracture behaviour is evaluated and compared with previous studies results, to present a comprehensive study of the mechanical properties of the material under different kind of solicitations.

Nurses experience significant stress and emotional exhaustion, leading to burnout and fatigue. This study assessed how the nurses’ mood and fatigue evolves during their shifts, and the lagged and accumulated factors that influence these phenomena. A two-level design with repeated measures was applied to a sample of 113 nurses, performing an ecological momentary assessment of different parameters and multilevel longitudinal two-level modelling of the data. Accordingly, mood appeared to be explained by effort, by the negative lagged effect of reward and by accumulated effort, each following a quadratic trend, and it was influenced by previously executing a direct care task. By contrast, fatigue was explained by the current and lagged effect of effort, by the lagged effect of reward and by accumulated effort, again following quadratic trends. Fatigue was also associated with direct care, and the prior effect of documentation and communication tasks. Mood was also explained by problem-focused and emotion-focused coping strategies, indicative of negative mood, and by support-seeking and refusal coping strategies. Hence, mood and fatigue do not depend on a single factor like workload but rather, on the evolution and distribution of tasks, as well as on the stress during a shift and how it is handled.

Additive manufacturing (AM) techniques are widely investigated for the cost-effective use of titanium (Ti) alloys in various aerospace applications. One of the AM techniques developed for such applications is plasma transferred arc solid free-form fabrication (PTA-SFFF). Materials manufactured through AM techniques often exhibit anisotropies in mechanical properties due to the layer-by-layer material build. In this regard, the present study investigates the isothermal directional fatigue of Ti-TiB metal matrix composite (MMC) manufactured by PTA-SFFF. This investigation includes rotating beam fatigue test, electron microscopy, and fatigue calculations. The fatigue experiments were performed at 350 ºC using specimen with the test axis oriented diagonally (45º) and parallel (90º) to the AM builds directions. The fatigue values from the current experiments along with literature data find that Ti MMC manufactured via PTA-SFFF exhibit fatigue anisotropy reporting highest strength in 90º and lowest in perpendicular (0º) AM build directions. Further, the electron microscopy investigations on 0º, 45º, and 90º AM build specimens reveal frequent TiB clusters in all three AM build directions and suggest that the spread of these TiB clusters play a role in fatigue anisotropy. Moreover, the fatigue calculations were performed using both the Paris’ and recently reported modified Paris’ equations. Comparison of R^2 values for these calculations show that modified Paris’ equation predicts the fatigue life of AM Ti-TiB MMC more accurately than the Paris’ equation.

Fatigue failure remains a critical concern in structural engineering and material science, prompting extensive research to understand and predict the behaviour of materials under cyclic loading conditions. The present study aims to investigate the fatigue life of carbon steel specimens containing opposite semicircular edge notches through a comprehensive experimental and numerical analysis. In this study, stress concentration factors (SCF, K_t) of rectangular plate with opposite semicircular notches are considered under uniform tensile stress to analyse the notch deformation because of stretching of plate. Furthermore, the research focuses on quantifying stress concentration factors (SCFs) for these notches based on S-N curves of carbon steel. The study employs a combination of experimental and numerical techniques to understand the influence of these notches on the fatigue performance of carbon steel structures. A plate with opposite semicircular edge single notches under the axial load creates stress concentration near the notch and it is much larger than the average stress on the plate. Both analytical and finite element methods are used to calculate the maximum stress around the notch. SOLIDWORKS Premium Student Edition 2023 has been employed for modelling and SOLIDWORKS Simulation Premium Student Edition 2023 has been used for stress analysis and fatigue notch factor of rectangular plate of size 31 mm x 25.4 mm x 6.35 mm. The uniform tensile load with a magnitude of 20195 N is applied on one sides of rectangular plate normal to the sides of notches with ratio h/r = 1, for the semicircular notch. The result obtained on both analytical and finite element methods are compared and the percentage of error has been evaluated. Subsequently, these specimens undergo fatigue testing under varying loading conditions to capture their fatigue behaviour. The acquired fatigue data is then plotted against stress amplitude to construct S-N curves, forming the foundation for assessing the fatigue life of the notched specimens. To complement the experimental findings and to gain a deeper understanding of the stress concentration phenomenon, numerical simulations are conducted using advanced finite element analysis (FEA) techniques. The finite element models are carefully calibrated against the experimental results to ensure their accuracy and reliability. The FEA simulations enable the determination of stress concentration factors at critical locations within the notched specimens, further validating the experimental observations. The investigation reveals crucial insights into the effect of opposite semicircular edge notches on the fatigue life of carbon steel structures. The obtained S-N curves allow engineers and designers to predict the fatigue life of components with similar notches, aiding in the development of reliable and durable structures in practical applications. Moreover, the stress concentration factors determined from the numerical simulations provide valuable data to assess the potential failure modes and to optimise designs, effectively mitigating fatigue-related failures. The combination of experimental and numerical approaches ensures a comprehensive and rigorous analysis of the fatigue behaviour in notched specimens, offering a reliable basis for making informed engineering decisions. The comparison between the analytical method and the Finite Element Method (FEM) demonstrated good agreement, with an error percentage of 4.272%. The analysis revealed that the specimen would experience failure after approximately 2882 cycles, with a maximum stress of 395.914 MPa. This research study enhances the understanding of fatigue life in carbon steel structures containing opposite semicircular edge notches and contributes valuable data to the field of fatigue mechanics. The outcomes serve as a valuable resource for professionals engaged in structural engineering, material science, and design optimisation, ultimately leading to safer and more durable industrial components in critical applications. The findings of this research contribute to the understanding of fatigue behaviour in carbon steel components with stress concentration effects caused by semicircular notches. Moreover, the validated numerical simulations and data curves facilitate the prediction of fatigue life and aid in determining the critical conditions leading to fatigue failure. In conclusion, this research highlights the significance of combining experimental testing with numerical simulations to comprehensively analyse the fatigue life of carbon steel specimens with opposite semicircular edge notches. The obtained stress concentration factors provide crucial information for structural integrity assessment and offer potential for further optimising design criteria to mitigate fatigue-related failures. The findings of this study could play a vital role in enhancing the reliability and safety of carbon steel structures subjected to cyclic loading conditions. The comprehensive experimental and numerical analyses establish a foundation for future studies exploring other materials and geometries with notches, fostering advancements in fatigue life prediction and structural integrity assessment.

In order to realize the performance degradation trend prediction accurately, a prediction method based on multi-domain features and temporal convolutional network (TCN) is proposed. Firstly, construct a high-dimensional feature set in the multi-domain of vibration signals, and use comprehensive evaluation indicators to preliminarily screen performance degradation indexes with good sensitivity and strong trend. Secondly, the kernel principal component analysis (KPCA) method is adopted to eliminate redundant information between multi-domain features, and construct a health index (HI) based on convolutional auto-encoder (CAE) network. Thirdly, a TCN-based performance degradation trend prediction model is constructed, and direct multi-step prediction is used to predict the performance degradation trend of the monitored object. On this basis, the validity of the proposed method is verified using the bearing public data, and it is successfully applied to performance degradation trend prediction of rolling contact fatigue specimen. The results show that the feature set can be reduced from 14 dimensions to 4 dimensions by using KPCA, while 98.33% of the information of the original feature set is retained. Furthermore, the method of constructing HI based on CAE network is effective. The change process of the HI constructed truly reflects the performance degradation process of the rolling contact fatigue specimen. Compared with the two commonly used HI construction methods, auto-encoding (AE) network and gaussian mixture model (GMM), this method has obvious advantages. At the same time, the prediction model based on TCN can accurately predict the performance degradation of the rolling contact fatigue specimen with the root mean square error 0.0146 and the mean absolute error 0.0105, which has better performance and higher prediction accuracy than the prediction model based on the long short-term memory (LSTM) network and the gated recurrent unit (GRU). This method has general significance and may be extended to the performance degradation prediction of other mechanical equipment/parts.

As the demand for liquefied petroleum gas (LPG) continues to increase worldwide, more LPG facilities are being constructed. However, the design and manufacture of pressure vessels used to store dangerous liquids or pressurised fluids, such as LPG, has been a major cause of hazards, including explosions and leakage. In this study, we aim to address this issue by designing and analysing a vertical pressure vessel with a capacity of 10 m3 of pressurised LPG in accordance with the American Society of Mechanical Engineers (ASME) code. Safety is the primary concern in designing pressure vessels due to the potential risks posed by accidents. Therefore, the main objective of this project is to design a pressure vessel that is safe from failure. The vessel is cylindrical with two elliptical heads, two nozzles, a manway and four leg supports, and we used Autodesk Inventor Professional 2023 for geometric modelling and Inventor Nastran for FEA analysis. To investigate the displacements, deflections and Von-Mises stresses in the pressure vessel, we used the finite element method, and Autodesk Inventor Nastran was employed for the analysis. Our results showed that changes to the structure of the pressure vessel were needed to reduce stress in the structure. Specifically, the displacement showed an inverse relationship with the tank section shell thickness. Moreover, we observed that the factor of safety increased linearly with shell thickness. We carefully considered permissible pressures and determined the required wall thickness to ensure acceptable maximum stresses. Our results indicate that the design is safe from failure, and the highest stresses are experienced by the manway followed by the shell, while the heads, nozzles and legs support experienced the lowest stresses. We also performed a theoretical calculation for the entire model and checked the results to ensure they were within the acceptable limits. In summary, our study highlights the importance of designing pressure vessels in accordance with ASME codes to ensure safety and prevent hazards caused by improper design and manufacturing. By using the finite element method, we identified potential stress points in the pressure vessel and were able to make modifications to improve its safety.

The work is devoted to the study of the mechanisms of damage accumulation in a polymer composite material (PCM) during fatigue loading. Mechanical testing of a fiberglass sample was carried out by cyclic tension accompanied by registration of acoustic emission (AE). For the recorded AE signals, the Fourier spectra were calculated and used for clustering with Kohonen self-organizing map. Relations between clusters and types of damage in the PCM structure were established. The analysis of the peak frequencies of the Daubechies D14-wavelet components of AE signals was carried out. Obtained results has allows one to describe the processes of destruction in the PCM sample. It has been established that, on the base of local formation of microdamages in the matrix and the fracture of the fibers detected during recording of the AE data, it is possible to predict the destruction of the polymer composite material, while the beginning of a material destruction can be registered if the damage identified as an adhesion failure is observed. Perspectives of application of adaptive fiber-optic AE sensors for structural monitoring of PCMs on the base of preliminary experimental results are considered and discussed.

(1) Background: Most hemodialysis patients may experience physiological and psychological stress. Exposure to nature has been previously reported to reduce the measures of psychological and physiological stress, and immune function. This study aimed to investigate psychological and physiological effects of integrated indirect forest therapy on chronic renal failure patients undergoing hemodialysis. (2) Methods: As a quasi-experiment, this study employed a nonequivalent control group, repeated measurements, and a non-synchronized design. A total of 54 participants were included: 26 and 28 in the experimental and control groups, respectively. During hemodialysis, five types of forest therapy stimuli (visual, auditory, olfactory, tactile, and motor) were applied 3 times per week for 4 weeks during 15-minute sessions. (3) Results: Positive but not negative emotion measures differed between the groups after the intervention. Fatigue and physiological stress levels were significantly reduced in the experimental group, whereas no significant difference was found between the groups on the measures of psychological stress. Activation of both the parasympathetic and sympathetic nervous systems was similar in both groups, as was the number of natural killer cells. (4) Conclusion: Integrated indirect forest therapy may help increase positive emotions and reduce fatigue and stress levels during hemodialysis in patients with chronic renal failure.

The effects of environmental media on the corrosion fatigue fracture behavior of 25CrMo steel were investigated. The media include air, and a 3.5 wt.% and a 5.0 wt.% NaCl solutions. Experimental results indicate that the media induces the initiation of corrosion fatigue cracks at multiple sites. The multi-cracking sites cause the changes in the crack growth directions, the crack growth rate during the coupling action of the media and the stress amplitude. The coupling effects are important for engineering applications and research. The probability and predictions of the corrosion fatigue characteristic life can be estimated using the 3-parameter Weibull distribution function.

This study demonstrates the efficacy of structured pruning and architectural fine-tuning on the YOLOv7-tiny model for eye state detection, emphasizing optimization for real-time applications. Structured pruning significantly reduced the model's complexity and storage size while maintaining high detection accuracy, as evidenced by stable precision, recall, and [email protected] metrics across iterations. Further fine-tuning adjusted the model's width and depth, optimizing efficiency and processing speed without compromising performance. These optimizations yielded YOLOv7-tiny variants that are both computationally efficient and accurate, suitable for resource-constrained environments. The findings highlight the critical role of model optimization in deploying effective neural networks for specific detection tasks in real-time scenarios.

An algorithm is proposed for discriminating the fatigue state of air traffic controllers based on ap-plying multispeech feature fusion using an FSVM to voice data, and for extracting eye-fatigue-state discrimination features based on PERCLOS eye data. For the speech algorithm and an eye-fatigue index, a new controller fatigue-state evaluation index based on the entropy weight method is proposed based on decision-level fusion of fatigue discrimination results for speech and the eyes. Experimental results show that the fatigue-state recognition accuracy rate was 84.81% for the fatigue state evaluation index, which was 3.36% and 1.86% higher than those for speech and eye assessments, respectively. The comprehensive fatigue evaluation index provides important reference values for controller scheduling and mental-state evaluations.

Multiaxial fatigue experiments under asynchronous loadings with four different loading frequency ratios were carried out on 30CrMnSiA steel. The experimental results show that the fatigue life decreases when the axial or torsion frequency increases from 1 to 2, while there is no significant change when the axial or torsion frequency increases from 2 to 4. The surface crack paths are observed and show that cracks initiate on the maximum shear stress amplitude planes, propagate approximately tens of microns, and then turn to propagate along the maximum normal stress planes. The number of secondary cracks increases when the axial or torsion frequency increases. Subsequently, the Bannantine-Socie and Wang-Brown cycle counting methods along with various multiaxial fatigue criteria and Palmgren-Miner’s cumulative damage rule were used for fatigue life prediction. The experimental results are consistent with the fatigue life predicted by the Bannantine-Socie method with the section critical plane criterion for 30CrMnSiA steel under asynchronous loading paths.

Myalgic encephalomyelitis/chronic fatigue syndrome (ME/CFS) is a disabling condition affecting millions of adults and children worldwide. Despite the development of multiple criteria sets for defining this disorder, agreement on the core symptoms and other implications of ME/CFS point to the importance of understanding their role in oral health care. Overall, care for the homebound and bedbound population with ME/CFS issues has been under-addressed in the literature to date and there has been little consideration of the oral health needs of this population. Evaluation, diagnosis and treatment of dental concerns may be hindered by many of the diverse symptoms of ME/CFS. The present paper utilizes the International Consensus Criteria (ICC) in discussing treatment considerations for the most severely affected patients with ME/CFS, both in oral evaluation and active care. While no specific dental pathology is linked to ME/CFS, proper care for the patient so affected must take into account the disorder’s symptoms and severity.

Fatigue in any material is a result of continuous irreversible degradation process. Traditionally, fatigue life is predicted by extrapolating experimentally curve fitted empirical models. In the current study, unified mechanics theory is used to predict fatigue life of Ti-6Al-4V under monotonic tensile, compressive and cyclic load conditions. The unified mechanics theory is used to derive constitutive model for fatigue life prediction using a three-dimensional computational model. The proposed analytical and computational models have been used to predict the low cycle fatigue life of Ti-6Al-4V alloys. It is shown that the unified mechanics theory can be used to predict fatigue life of Ti-6Al-4V alloys by using simple predictive models that are based on fundamental equation of the material, which is based on thermodynamics associated with degradation of materials.

The Ti-6Al-4V alloy is widely used in the manufacture of components that should have low density, high corrosion resistance, and fatigue strength. The fatigue strength can be improved by surface modification. The aim of this study was to determine the influence of plasma nitriding on the fatigue behavior of Ti-6Al-4V alloy with a lamellar microstructure (Widmanstätten type). Nitriding was executed at 720 °C for 4 hours in an atmosphere with N₂, Ar and H₂. Samples microstructure characterization was carried out by X-ray diffraction analysis, optical microscopy and scanning electron microscopy. The average roughness of the specimens was determined, and fatigue tests were executed in a bending-rotating machine with reverse tension cycles (R= -1). X-ray diffraction analysis revealed the matrix phases α and β, and the phases Ɛ-Ti₂N and δ-TiN in the nitrided alloy. A nitrogen diffusion layer was formed between the substrate and the titanium nitrides. Plasma nitriding resulted in an increase in low cycle fatigue strength, whereas at high cycles, both conditions exhibit similar behavior. The fracture surface of the fatigue tested specimens clearly revealed the lamellar microstructure. The fracture mechanism appears to be due to cracking at the interface of α and β phases of the lamellar microstructure.

Acoustic emission (AE) has proven to be a very useful technique for determining damage in ceramic matrix composites (CMCs). CMCs rely on various cracking mechanisms which enable non-linear stress-strain behavior with ultimate failure of the composite due to fiber failure. Since these damage mechanisms are all micro-fracture mechanisms, they emit stress waves ideal for AE monitoring. These are typically plate waves since for most specimens or applications one dimension is significantly smaller than the wavelength of the sound waves emitted. By utilizing the information of the sound waveforms captured on multiple channels from individual events, the location and identity of the sources can often be elucidated. The keys to the technique are the use of wide-band frequency sensors, digitization of the waveforms (modal AE), strategic placement of sensors to sort the data and acquire important contents of the waveforms pertinent for identification, and familiarity with the material as to the damage mechanisms occurring at prescribed points of the stress history. The AE information informs the damage progression in a unique way which adds to the understanding of the process of failure for these composites. The AE methodology was applied to composites tested in fatigue at different frequencies where identification of when and where AE occurred coupled with waveform analysis leads to source identification and failure progression.

Abstract—The static and fatigue analysis of plates with holes, made of 2D woven roving composites, is conducted. The parametrization of convex holes is proposed. Experimental results of specimens without holes and with different shapes of notches are discussed. The fatigue behaviour is considered with the use of the low cycle fatigue method. The analysis is supplemented by the numerical finite element modeling. The present work is an extension of the results discussed in the literature. The finite element modeling of plates with holes is presented in details in Ref [1-3] including also the problems of the accuracy. The experimental results and the form of specimens are shown in Ref [4]. Two parametrical description of static and fatigue behaviour of plates with holes characterizes the goal and the novelty of the paper. The fuzzy approach is employed to reduce the number of experimental data [5].

The new slide roller burnishing (SRB) method has been developed to produce mirror-like surfaces. Unlike conventional roller burnishing (RB), SRB is implemented through a unique device that allows the axes of the deforming roller and the rotary workpiece to cross resulting in a relative sliding velocity that can be controlled (in magnitude and direction) by varying the crossing angle. In the present work, the effect of SRB on the fatigue behavior of AISI 316 steel fatigue specimens was investigated by comparing with a conventional RB using the basic correlation in surface engineering: finishing–surface integrity (SI)–operating behavior. To obtain a more representative picture of the comparison, we implemented each method (RB and SRB) with two combinations of governing factors: (A) a radius of the roller toroidal surface of 3 mm, a burnishing force of 250 N and feed rate of 0.05 mm/rev (RB-A and SRB-A) and (B) a radius of the roller toroidal surface of 4 mm, a burnishing force of 550 N and feed rate of 0.11 mm/rev (RB-B and SRB- B). Both SRB-A (crossing angle of –45°) and SRB-B (crossing angle of –30°) achieved mirror-finish surfaces. SRB-B lead to the greatest fatigue strength and, thus, the longest fatigue life among all tested processes. SRB-B created the deepest zone (&gt;0.5 mm) with residual compressive macro-stresses and a clearly defined modified surface layer, whose thickness of more than 20 m is about twice that created by the other three processes.

Fastener holes are among the most common natural stress concentrators in metal structures. The life cycles of various structural elements, such as those in aircraft structures, automobiles, and rail-end bolt joints are limited by fatigue damage around the holes. An effective approach to delay the formation and growth of fatigue macrocracks is to introduce residual hoop compressive stresses around the holes. Two methods have become established in the prestressing of fastener holes in aircraft components: split sleeve and split mandrel, which implement one-sided processes. The common disadvantage of both methods is the complex procedure due to the need for high accuracy of the initial holes. This article presents a new modified split mandrel method providing the same tightness (interference fit) with a wide tolerance of the pre-drilled hole diameters reducing the number of technological cycle steps and production costs. То implement the new method, a functionally connected tool and a device with a hydraulic drive were developed. An extensive experimental study of 2024-T3 AA specimens was carried out to evaluate the effectiveness of the method under a high scattering of the pre-drilled holes. The new method provided a deep zone of residual hoop compressive stresses on both faces of the specimens after cold working and after hole final reaming. The removal of a plastically deformed layer around the hole of suitable thickness during the final reaming decreased the axial gradient of residual hoop stress distribution. Fatigue tests on a tensile pulsating cycle verified the effectiveness of the modified split mandrel method to significantly increase the fatigue life by 6.6 times based on cycle fatigue strength compared to the conventional case of machining the holes. The obtained S-N curves for three groups of samples with initial hole diameters of 8.0, 8.1, and 8.2 mm which were cold worked with the same tightness of 0.32 mm and final reamed, aligned well indicating that the new method can provide constant fatigue strength for a given stress amplitude.

The high demands of caring for and raising a child with autism spectrum disorder on a daily basis fatally lead parents to the appearance of physical and mental fatigue. This study aimed to assess the effect of social support and spirituality on the fatigue of parents with children with autistic spectrum disorder. A cross-sectional study with a convenience sample was conducted in Schools of Special Education in Attica (Greece). The sample consisted of 123 parents who completed The Fatigue Assessment Scale (FAS), the Multidimensional Scale of Perceived Social Support (MSPSS), and the Functional Assessment of Chronic Illness Therapy Spiritual Well-Being Scale (FACIT Sp-12) to measure the levels of fatigue, social support, and spirituality, respectively. Demographic data were, also, recorded. Data analysis was applied using IBM SPSS 21.0. The mean age was 47.3 years old, 81.3% were women, and 38.9% stated much / very much religious. The mean of total FAS was 28.4 (SD±7.5), of total FACIT Sp-12 was 31.5 (SD±8.7), and of total MSPSS 5.1 (SD±1.1). Higher levels of total MSPSS and FACIT Sp-12 were associated with lower total FAS (r= -0.50, p &lt;0.001 and r= -0.49, p&lt;0.001 respectively). Social support and spirituality are significant predictors of fatigue.

Al has very good corrosion resistance and corrosion properties. The corrosion resistance of Al cast alloys is different because these alloys contain a lot of elements. Especially in secondary alloys which contain more impurity elements from which Fe is the most common. This study deals with secondary AlSi7Mg0.3 cast alloys which contain more Fe and are affected by a chloride corrosion environment. This environment was selected based on the application of castings in the automo-tive industry. The main object was to research the effect of such an environment on basic me-chanical properties and fatigue properties. The results show that a higher Fe content does not lead to a significant reduction in the properties of the casting and the chloride environment is not so harmful. Therefore, can be stated that the investigated secondary sand-cast experimental materials can replace the primary alloys without losing the required corrosion and mechanical properties.

Shot peening is an attractive technique for fatigue enhanced performance of metallic components, because it promotes crack initiation retardation and later crack growth. Engineering design based on fatigue crack propagation predictions applying the principles of fracture mechanics is commonly used in aluminum structures for aerospace engineering. The main purpose of present work was to analyze the effect of shot peening on the fatigue crack propagation of the 7475 aluminum alloy, under both constant amplitude loading and periodical overload blocks. The tests were performed on 4 and 8 mm thickness specimen's with stress ratios of 0.05 and 0.4. The analysis of the shot-peened surface showed a small increase of the micro-hardness values, due to the plastic deformations imposed by shot peening. The beneficial effect of surface peening on fatigue crack growth rates is quite limited to an increasing near the threshold. The specimens’ thickness has only marginal influence on the crack propagation, in opposite to the stress ratio. Periodic overload blocks of 300 cycles promotes a reduction of the fatigue crack growth rate for both intervals of 7,500 and 15,000 cycles.

As a new type of high-performance material, gradient structural steel is widely used in engineering fields due to its unique microstructure and excellent mechanical properties. For the prevalent fatigue failure problem, the rate of change of the local grain size gradients along the structure (referred to as the gradient rate) is a key parameter in the design of gradient structures, which significantly affects the fatigue performance of gradient structural steel. In this work, a method of ‘Voronoi primary + secondary modeling’ is adopted to successfully establish three typical high-strength steel models corresponding to the convex, linear, and concave type gradient rates for gradient structures, focusing on the stress-strain response and crack propagation in structural steel with different gradient rates under cyclic loading. It is found that the concave gradient rate structural model is dominated by finer grains with larger volume fraction, which is conducive to hindering fatigue crack propagation and has the longest fatigue life; the linear structure is the second one, and the convex structure is the shortest one. The simulation results in this work are consistent with the relevant experimental phenomena. Therefore, when regulating the gradient rate, priority should be given to increasing the volume fraction of fine grains and designing a gradient rate structure dominated by fine grains to improve the fatigue life of the material.

The Interdisciplinary Canadian Collaborative ME Research Network (ICanCME), established in 2019, aims to foster research in Canada and contribute to finding the causes and possible treatments for myalgic encephalomyelitis /chronic fatigue syndrome (ME/CFS), thereby reducing the impact of ME/CFS on the health of Canadians. The main objectives of this paper are to suggest standards for ME/CFS research for the collection of data from participants (Recommended Data Elements) and to consider other factors, such as design, language, cultural issues, equity, and diversity. Consensus of the relevant contents of this research guideline was reached during the ICanCME working group meetings and were based on existing guidelines. Members of the working group contributed to guideline development based on their respective expertise. The proposed research guidelines could improve research quality and advance knowledge in the field of ME/CFS, and ultimately benefit ME/CFS patients.

Understanding the pathophysiology of Myalgic Encephalomyelitis/Chronic Fatigue Syndrome (ME/CFS) is critical for advancing treatment options. This review explores the novel hypothesis that herpesviruses' infection of endothelial cells (ECs) may underlie ME/CFS symptomatology. We review evidence linking herpesviruses to persistent EC infection and the implications for endothelial dysfunction, encompassing blood flow regulation, coagulation, and cognitive impairment – symptoms consistent with ME/CFS and Long COVID. The paper provides a synthesis of current research on herpesvirus latency and reactivation, detailing the impact on ECs and subsequent systemic complications, including latent modulation and long-term maladaptation. We suggest that the chronicity of ME/CFS symptoms and the multisystemic nature of the disease may be partly attributable to herpesvirus-induced endothelial maladaptation. Our conclusions underscore the necessity for further investigation into the prevalence and load of herpesvirus infection within ECs of ME/CFS patients. This review offers a conceptual advance by proposing an endothelial infection model as a systemic mechanism contributing to ME/CFS, steering future research towards potentially unexplored avenues in understanding and treating this complex syndrome.

Muscle fatigue caused by using staplers affects the surgical procedures of surgeons. Compared to manual staplers, electric staplers decrease the muscle fatigue by replacing repeated gripping and releasing with automatic model. Still powered by the battery, the electric staplers are confronted with new operation fatigue due to the extra weight of the battery. The weight and manual operation of the electric stapler can cause user's muscle fatigue. To tackle the unsettled fatigue issue, the study is to propose a new design method to offset the influence of extra weight of the battery attached to the electrical stapler by changing the opening and closing of the stapler end clamp to electric control. The purpose of this study is to verify whether the design of this electric stapler can offset the impact of weight. Experiments are set up to test the feasibility of the design on 12 male Chinese surgeons. The muscle fatigue is indicated by measuring the EMG (electromyography) signal, and the stapler's working effect is indicated by measuring the end movement of the stapler. The result shows the new-designed stapler reduce the operation fatigue, counteracting the impact of the battery weight.

A progressive FEA fatigue degradation model for composites was developed and implemented using a UMAT user material subroutine in Abaqus. Numerical results were compared to experimental strain field data from high frequency Digital Image Correlation (DIC) of split disk fatigue testing of pressure vessel cut outs with holes. The model correctly predicted the onset and evolution of damage in the matrix as well as the onset of fiber failure. The model use progressive failure analysis based on the maximum strain failure criterion, the cycle jump method and Miner sum damage accumulation rule. A parameter study on matrix properties was needed to capture the scatter in strain fields observed experimentally by DIC. S-N curve for the matrix material had to be lowered by 0% to 60% to capture the experimental scatter. The onset of local fiber failure had to be described by local S-N curves measured by DIC having 2.5 times greater strain than that of S-N curves found from standard coupon testing.

This study investigated the fatigue properties and interfacial strengthening mechanisms of Al6061-to-Cu dissimilar welded joints via electromagnetic pulse welding (EMPW). The load-bearing capacity of the joints at discharge voltages of 14 kV and 16 kV was superior to that of 12 kV. Meanwhile, the fatigue life of 14 kV joints was one order of magnitude higher than that of 12 kV. The SEM observation on the fatigue fracture surface shows that the typical “tire-mark” fatigue striation just appeared on the 14 kV joint, indicating higher ductility for handling more extended plastic deformation. The high EBSD acquisition was achieved except for the transition zone due to the formation of ultra-fine nanocrystalline Al2Cu phase and amorphous phase, along with many dislocations. Dense low-angle grain boundaries (LAGBs) and refined grains are formed along the bonding interface. This indicates that severe plastic deformation induced dislocations to form the substructure in such an instant (40-60 μs) during the high-velocity collision. The interfacial strength is not only due to the continuous interfacial diffusion layer with a “wave-like” or “inverted hook-like” pattern but also benefits from refined grains along the interface and in the transition zone, as well as the hybrid amorphous-nanocrystalline microstructure, which strengthens the joint through increasing ductility induced by refined grains and regulating amorphous or nanocrystalline phases to affect the balance between strength and ductility of the Al/Cu joint.

The work presents the results of numerical fatigue analysis of a turbine engine compressor blade, taking into account the values of initial stresses resulting from surface treatment - shot-peening. The values of the residual stresses were estimated experimentally using X-ray diffraction. The paper specifies the values of the residual stresses on both sides of the blade and their reduction due to the cutting through the blade - relaxation. The obtained values of the residual stresses were used as initial stresses in the numerical fatigue analysis of the damaged compressor blade, which is subjected to resonant vibrations of known amplitude. Numerical fatigue ε-N life analysis was based on the several fatigue material models: Manson’s, Mitchell’s, Baumel-Seeger’s, Muralidharan-Manson’s, Ong’s, Roessle-Fatemi’s and Median’s, and also on the three models of cyclic hardening: Manson’s, Xianxin’s, and Fatemi’s. Because of this approach, it was possible to determine the relationship between the selection of the fatigue material ε-N model and the cyclic hardening model on the results of the numerical fatigue analysis. Additionally, the calculated results were compared with the results of experimental research, which allowed for a substantive evaluation of the obtained results. These results are of great scientific and practical importance. The problem of determining the fatigue life of blades with defects operating under resonance vibrations is one of the original tasks in the field of fracture mechanics and experimental mechanics. The results obtained are of great importance in the aviation industry and can be used during engine maintenance and inspections to assess the suitability of blades with defects in terms of the needs of further work. This aspect of engineering maintenance is of great importance from the aircraft safety point of view.

A subset of patients with schizophrenia experience physio-somatic symptoms reminiscent of chronic fatigue and fibromyalgia. In schizophrenia, these symptoms contribute to impaired quality of life, and are strongly related to neuro-cognitive deficits, and increased IgA responses to tryptophan catabolites. Negative and PHEM (psychosis, hostility, excitation, mannerism) symptoms, psychomotor retardation (PMR) and formal thought disorders, appear to be manifestations of a single trait reflecting overall severity of schizophrenia (OSOS). In this study, 120 patients with deficit schizophrenia (DEFSCZ) and 54 healthy subjects were assessed with the FibroFatigue (FF) rating scale, and the above-mentioned symptom domains as well as neuro-cognitive tests and biomarkers were measured. In DEFSCZ, there were robust associations between the FF score and all above-mentioned symptom domains, and impairments in semantic and episodic memory and executive functions. Furthermore, the FF score loaded highly on an OSOS latent vector (LV), which showed adequate convergent validity, internal consistency reliability and predictive relevance and fitted a reflective model. Soft Independent Modelling of Class Analogy (SIMCA) showed that the FF items discriminated DEFSCZ from controls with an overall accuracy of 100%. Interleukin IL-1β, IL-1 receptor antagonist (sIL-1RA), tumour necrosis factor (TNF)-α and CCL-11 (eotaxin) explained 66.8% of the variance in the FF score and 59.4% of the variance in OSOS. In conclusion, these data show that physio-somatic symptoms are a core component of the phenomenology of DEFSCZ and are largely mediated by neurotoxic effects of activated immune pathways, including aberrations in CCL-11, IL-1β and TNF-α signalling.

Chronic fatigue syndrome (CFS) is a disease in which fatigue that interferes with daily life persists for six months or longer. The number of patients with CFS is increasing, as CFS-like symptoms have been reported to occur in the sequelae of both COVID-19 infection and the SARS-CoV-2 vaccine, both of which have become significant issues in recent years. While the pathogenesis mechanism is not yet fully understood, research suggests that oxidative stress (OS) may play a role in the development of CFS. In this paper, we discuss the antioxidant potential of the antioxidant formulation Twendee M® (TwM) and the results of a questionnaire that monitored changes in symptoms before and after TwM in a total of 23 men and women diagnosed with CFS. TwM is a supplement containing 15 different ingredients, and has a strong antioxidant capacity that cannot be achieved with a single antioxidant ingredient. The results of the questionnaire showed that TwM significantly improved all of the major symptoms of CFS, including fatigue, muscle pain, joint pain, sleep disturbance, decreased memory and concentration, and headache. TwM was shown to alleviate various symptoms of CFS and improve quality of life.

For underwater vehicles navigating in Arctic Sea ice-covered waters, fatigue damage is a crucial issue. Many scholars have conducted low-temperature fatigue analysis on low-temperature ma-terials and substrate platforms for ships, and the results show that low-temperature is beneficial for improving the mechanical properties of materials. However, they mainly focus on low-temperature performance experiments and simulation analysis of standard components of materials, and there are very few fatigue life experimental studies on underwater vehicle me-chanical structures. This paper conducts experimental investigations on a scaled model of an underwater vehicle rudder mechanism in a polar environment laboratory. Using a comparative analysis method involving simulations and experiments, the low-temperature fatigue test data of the scaled underwater vehicle rudder mechanism are analyzed, and the quantified analysis be-tween fatigue and different low-temperature loading cycles, as well as the influence of icing on the fatigue life, is explored. It is indicated that the arctic environment can decrease the fatigue life of the underwater vehicle rudder mechanism by deteriorating its material properties. The paper builds the foundation for the fatigue life of an underwater vehicle rudder mechanism in arctic low-temperature environments.

Fatigue fractures in materials are the main cause of approximately 80% of all material failures, and it is believed that such failures can be predicted and mathematically calculated in a reliable manner. It is possible to establish prediction modalities in cases of fatigue fracture, according to three fundamental variables in fatigue, such as volume, number of fracture cycles, as well as applied stress, with the integration of Weibull constants (length characteristic). This investigation was carried out mechanical fatigue tests on specimens smaller than 4 mm2 in section of different industrial materials for their subsequent analysis through precision computed tomography in search of microfractures. The measurement of these microfractures, along with their metrics and classifications, was recorded. A convolutional neural network trained with deep learning was used to achieve the detection of microfractures in image processing. The detection of microfractures in images with 480x854 or 960x960 pixels is the primary objective of this network, and its accuracy is above 95%. Images that have microfractures and those that do not are classified by the network. Subsequently, by means of image processing, the microfracture is isolated. Finally, the images that do contain this feature are interpreted by image processing to obtain their area, perimeter, characteristic length, circularity, orientation, and type microfracture metrics. All values will be obtained in pixels and converted to metric units (μm) through a conversion factor based on image resolution.