The increasing demand for higher power in rocket launchers is driving the development of higher power nozzles, achieved essentially by increasing the expansion ratio. However, this can lead to flow separation and resulting unsteady, asymmetrical forces, called side loads, which can limit the life of both the nozzle itself and other engine components. If this problem can be overcome, engine performance can be significantly increased. Therefore, various separation control methods have been proposed, but none have been fully implemented to date due to the uncertainties associated with modeling and predicting the flow phenomena. A numerical study of high area ratio rocket engine is presented to analyze the aeroelastic performance of the structure under the condition of flow separation. The finite volume method, the 2nd order upwind scheme and the extended wall function are used to analyze the flow inside the rocket nozzle and the transition of the Free Shock Separation (FSS) to Restricted Shock Separation (RSS) separation pattern ) to be discussed in detail. Since the location of the flow separation point depends heavily on the flow.

Pea shoots is a popular vegetable in certain regions of the world due to their unique taste and abundance of health-promoting phytochemicals. The perishable nature and susceptibility of root rot of pea shoots necessitate a new soilless production system located close to the market. This study compared the growth of pea shoots using various cultivation methods in LED plant factory. The results showed that early topping (4 days after transplanting, ET) promoted early harvest compared to later topping (20 days after transplanting, LT) and increased the number of harvested shoots by extending the harvest time to 2.8 times, ultimately resulting in a substantial yield improvement. Moreover, the yield of ET with lower planting density (72 plants m-2, ET-LD) was 8.7% higher than ET with higher planting density (126 plants m-2, ET-HD). Particularly, the average fresh weight of individual pea shoots under ET-LD exceeded that of ET-HD by 48.9%. It is advisable to consider adopting ET-LD for the cultivation of pea shoots in LED plant factory. Based on ET-LD, the yield, nutritional quality, and light use efficiency of pea shoots were further explored at different stages under three levels of light intensity (50, 100, 150 μmol m-2 s-1). Contrasted against the light intensity of 50 μmol m-2 s-1, the average fresh weight per pea shoots, number of harvested, and total fresh yield under light intensity of 150 μmol m-2 s-1 treatment increased by 60.2%, 62.8%, and 165.1%, respectively. Meanwhile, the fresh weight per pea shoots, photosynthetic capacity, soluble sugar and vitamin C levels in leaves, as well as light use efficiency and photon yield, initially increased and then decreased with the extension of the planting period. Among these, soluble sugar, LUE, and PY started to decrease after reaching the maximum value at 60-70 days after transplanting. In conclusion, light intensity of 150 μmol m-2 s-1 with a photoperiod of 16 h d-1 using LEDs, combined with early topping within a planting period of 60-70 days, proves to be suitable for the hydroponic production of pea shoots in LED plant factory.

Silicon has a theoretical specific capacity of 4200 mAh g−1, which is considered to have significant potential for anode materials in lithium-ion batteries (LIBs). However, the volume change that occurs in silicon during charging and discharging affects the development of commercial applications. In this work, a yolk-shell structured Si@void@C anode material has been developed to address this problem. The silicon nanoparticle yolk material is obtained by recycling kerf-loss (KL) Si waste from the photovoltaic industry, the carbon shell is prepared via a hydrothermal process with glucose, and the sacrificial interlayer is Al2O3. The synthesized material is used to fabricate anodes that show a high reversible capacity of 836 mAh g−1 at the current density of 0.1 A g−1 after 100 cycles, with a Coulomb efficiency of 71.4%. This work demonstrates a relatively low-cost approach to turn KL Si waste into value-added materials for LIBs.

This review will explore the four major pillars required for design and development of an saRNA vaccine: antigen design, vector design, non-viral delivery systems, and manufacturing (both saRNA and lipid nanoparticles (LNP)). In will report on the major innovations, preclinical and clinical data reported in the last five years and will discuss future prospects.

This study provides a comprehensive analysis of the conformational dynamics of pseudo-endocannabinoid receptors (p-CBRs) CB₁ and CB₂ in response to ligand binding. The ligands studied include N-arachidonoyl dopamine (NADA), Cannabidiol (CBD), known agonists (FUB-MDMB and E3R), and inverse agonists (Taranabant and AM630). Using homology models based on crystal structures (PDB ID: 5U09 for CB₁ and 5ZTY for CB₂), molecular docking, and molecular dynamics (MD) simulations, the research validates the structural integrity and dynamic behaviours of these pseudo-receptors. Induced-fit docking revealed NADA as having the highest binding affinity for both receptors, with docking scores of −13.92 kcal/mol for CB₁ and −13.32 kcal/mol for CB₂, facilitated by key hydrogen bond interactions. MD simulations over 250 ns at ~298 K showed successful equilibration, indicating the most stable interaction for NADA, thereby further validating the models. CB₁ and CB₂ exhibited distinct conformational responses to ligands, with Cα RMSD and Cα RMSF analyses suggesting a more rigid binding pocket for CB₁ and a flexible binding pocket for CB₂. These findings highlight the significance of receptor behaviour and dynamics in the development of cannabinoid-based therapeutics, supporting the potential of CBD and NADA as modulators for CB₁ and CB₂, respectively.

In this work, we demonstrate the preparation of easy-to-fabricate nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics and examine their properties including tunnel magnetoresistance, magnetic field sensitivity and temperature coefficient of the tunnel magnetoresistance. The tunnel magnetoresistance of nanogranular, strontium ferromolybdate/strontium molybdate core-shell ceramics was modeled yielding values suitable for magnetoresistive sensor application. Such structures possess a narrow peak of magnetic flux sensibility located at about 125 mT. For magnetic flux measurement, single domain granules with superparamagnetic behavior should be applied. The predicted TMR magnetic flux sensitivities for granules with superparamagnetic behavior amount to about 7.7 % per T and 1.5 % per T for granules sizes of 6.8 nm and 4 nm, respectively. A drawback of the tunnel magnetoresistance of such nanogranular core-shell ceramics is the unacceptable large value of the temperature coefficient. Acceptable values, lower than 2 % per K, are obtained only at low temperatures (less than 100 K) or large magnetic flux densities (exceeding 6 T). Therefore, a Wheatstone bridge configuration should be adopted for magnetoresistive sensors design to compensate the effect of temperature.

Materials engineering based on metal oxides for manipulating the solar spectrum and producing solar energy have been under intense investigation over the last years. In this work, we present NiO thin films double-doped with niobium (Nb) and nitrogen (N) as cation and anion dopants (NiO:(Nb,N)) to be used as p-type layers in all oxide transparent solar cells. The films were grown by sputtering a composite Ni-Nb target on room-temperature substrates in plasma containing 50% Ar, 25% O2 and 25% N2 gases. The existence of Nb and N dopants in the NiO structure was confirmed by the Energy Dispersive X-Ray and X-Ray Photoelectron Spectroscopy techniques. The nominally undoped NiO film, which was deposited by sputtering a Ni target and used as the reference film, was oxygen-rich, single-phase cubic NiO, having a visible transmittance of less than 20%. Upon double doping with Nb and N the visible transmittance of NiO:(Nb,N) film increased to 60%, which was further improved after thermal treatment to around 85%. The respective values of the direct band gap in the undoped and double-doped films were 3.28 eV and 3.73 eV just after deposition and 3.67 eV and 3.76 eV after thermal treatment. The changes in the properties of the films such as structural disorder, direct and indirect energy band gaps, Urbach tail states and resistivity were correlated with the incorporation of Nb and N in their structure. The thermally treated NiO:(Nb,N) film was used to form a diode with a spin-coated two-layer, mesoporous on top of a compact, TiO2 film. The NiO:(Nb,N)/TiO2 heterojunction exhibited visible transparency of around 80%, showed rectifying characteristics and the diode’s parameters were deduced using the I-V method. The diode revealed photovoltaic behavior upon illumination with UV light exhibiting a short circuit current density of 0.2 mA/cm2 and open-circuit voltage of 500 mV. Improvements of the output characteristics of the NiO:(Nb,N)/TiO2 UV-photovoltaic by proper engineering of the individual layers and device processing procedures are addressed. Transparent NiO:(Nb,N) films can be potential candidates in all-oxide ultraviolet photovoltaics for tandem solar cells, smart windows and other optoelectronic devices.

Most malignant ovarian germ cell tumors (MOGTCs) have a very good prognosis and can be cured by chemotherapy, with yolk sac tumors (OYSTs) having the worse prognosis among MOGCTs. These tumors are rare and can benefit in the next future from specific therapeutic strategies after failure of platinum-based first-line and salvage regimens. In collaboration with EORTC SPECTA, we have developed a project to explore the molecular characteristics of OYST. The pilot part of the project was performed using retrospective samples and ten OYST patients including relapsed and disease free patients. The molecular analysis was performed using FoundationOne CDx. For each patient, the following variables are described in the molecular report provided by FMI (Fondation Medicine Incorporation): alteration type (SNV, deletion), actionable gene alteration, therapies approved in EU (patient's tumor type and other tumor types), tumor mutational burden (TMB) and microsatellite instability (MSI) status. A total of 10 patients with OYST diagnosed between 2007 and 2017 were analyzed. Four patients (40%) had a molecular alteration, according to the FMI test. A subset of three patients (33.3% of all patient) harbored targetable (KRAS, KIT, ARID1A) oncogenic mutations. Two patients at relapse harbored a targetable mutation. In this retrospective study, we were able to identify clinically relevant molecular alterations for all relapsed patients with molecular analysis. Dedicated studies are needed to demonstrate if they could benefit from specific therapeutic strategies after failure of platinum-based first-line and salvage regimens and if the presence of a molecular alteration could be linked to patients’ outcome.

In the present work, an innovative range of foams, based on flax gum-filled epoxy resin was developed, reinforced or not by flax fibers. Foams and composites with different gum and epoxy resin contents were produced and characterized for mechanical and thermal performances. To enhance the organic flax gum filler's cross-linking, we exploited the oxidized components' reactivity with the amine hardener (isophorone diamine). We compared the materials obtained with those derived from the native components. Flax gum and fibers were primarily characterized by chemical analysis, NMR, and FTIR to evaluate the mild oxidation of native materials. The formation of chemical bonds between oxidized polymer chains, epoxy resin, and hardener has been evidenced by FTIR, and the materials were then studied by SEM, X-ray computed micro-tomography (CT), and submitted to mechanical and thermal tests. The relevance of oxidation treatment was highlighted, through a significant increase in density and mechanical performances (+36% and +81%, respectively for the 100% flax gum material). The positive effect of flax fibers on homogeneity evidenced through micro-CT analysis was also clearly addressed. This set of promising results paves the way for future development of fully flax-based insulation composite materials.

In the current study nanocellulose was isolated from walnut shell using mechanical and chemical methods. This study highlights the particle size, morphology and these methods’ efficiency in nano structure extraction. The difference between morphology and size of the particles (of the both extracted methods) were investigated by field emission scanning electron microscopy (FESEM). Walnut shell is an agro-waste material with source of lignin and cellulose. Ball mill-ing with different times, in the presence and absence of additive and acid hydrolysis were used as mechanical and chemical methods, respectively. The result showed mechanical method is unable to extract nanoparticle and just reshape the walnut shell. Milling time were also found important in morphology of fiber extracted. FE-SEM images represented that structure mean diameter of using ball mill was 1± 5 μm while hydrolysis acid method extract nano particle with mean diameter of 40± 20 nm.

Water electrolysis is a highly efficient route to produce ideally clean H2 fuel with excellent energy conversion efficiency and high gravimetric energy density, without producing carbon trace unlike steam methane reforming, and resolves the issues of environmental contamination via replacing the conventional fossil fuel. Of special importance lies in the advancement of highly effective non-precious catalysts for the oxygen evolution reaction (OER). The electrocatalytic activity of an active catalyst mainly depends on the material conductivity, accessible catalytically active sites, and intrinsic OER reaction kinetics, which can be tuned via introducing heteroatom N in the catalyst stricture. Herein, an efficacious nitrogenation of CuS has been accomplished, which was synthesized using hydrothermal procedure, and characterized for their electrocatalytic activity towards OER. The nitrogen-doped CuO@CuS (N,CuO@CuS) electrocatalyst exhibits superior OER activity than pristine CuS (268 and 602 mV), achieving the low overpotential of 240 and 392 mV at a current density of 10 and 100 mA/cm2, respectively, ascribed to the favorable electronic structural modification triggered by nitrogen incorporation. The N,CuO@CuS also exhibits excellent endurance under varied current rates and a static potential response over 25 h stability measured at 10 and 100 mA/cm2.

Graphene was synthesized through a two-step pyrolysis method using waste candlenut (Aleurites moluccanus) shells as the precursor. Cerium (Ce)/graphene composites were prepared via an impregnation technique. The resulting graphene and Ce/graphene were characterized using various analytical methods, including Scanning Electron Microscopy with Energy-Dispersive Spectroscopy (SEM-EDS), X-ray Diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Transmission Electron Microscopy (TEM), Thermo Gravimetric Analysis (TGA), Fourier Transform Infrared (FTIR) spectroscopy, Cyclic Voltammetry (CV), and Linear Sweep Voltammetry (LSV). The bio-carbon produced predominantly exhibited a graphene structure with flat carbon morphology and an interlayer distance of 0.33 nm. This structural information is supported by XRD data, which shows a broad and weak peak at 2θ = 26° corresponding to the C (002) plane, indicative of graphene presence. FTIR, XPS, and Raman spectroscopy further confirmed the presence of graphene through the detection of Csp2 aromatic bonds and the characteristic D, G, and 2D peaks. Notably, the performance of cerium can be enhanced by the incorporation of graphene, attributed to the large surface area and chemical interactions between Ce and graphene. Consequently, candlenut-derived graphene shows potential as a supportive material for modifying the properties of cerium, thereby opening avenues for various advanced applications, such as sustainable and high-performance energy storage systems.

A configurable design of a microstrip square spiral RFID tag antenna, for a wide range of microwave frequencies in S- and C-band, is presented. The design is parameterized in dimensions, and hence changing the design frequency (or frequencies) is easy, by changing only an initial value for the spiral geometry. A tag specimen was fabricated using Cu electroplating technique according to the design for frequencies of interest in the areas of 2.4 and 5.8 GHz. The substrate material is a 320 μm high resistivity Si and the bridge dielectric is a 15μm polyimide PI2525. The microfabrication process involves steps of metallic structure pattern transfer techniques with optical UV lithography procedures. The reflection coefficient and gain of the specimen were measured inside an anechoic enclosure using a vector network analyzer (VNA) and a TEM horn test antenna over a frequency range of up to 6 GHz. Simulated and measured results are presented and discussed, exhibiting reasonable agreement.

To realize the utilization of peanut shell, this study investigates the combustion behavior, chemical kinetics, and thermodynamic parameters of peanut shell using TGA under atmospheric air. Results indicate that increasing the heating rate leads to higher ignition, burnout, and peak temperatures, as observed in the TG/DTG curves shifting to the right. Analysis of combustion performance parameters suggest that higher heating rates can enhance combustion performances. Kinetic analysis using two model-free methods, KAS and FWO, shows that the activation energy (Eα) ranges from 93.30 to 109.65 kJ/mol for FWO and 89.72 to 103.88 kJ/mol for KAS. The data fit well with coefficient of determination values (R2) close to 1. Pre-exponential factors using FWO range from 2.19×106 to 8.06×107 s–1, and for KAS range from9.72×105 to 2.25×107 s–1. Thermodynamic analysis indicates a low-energy barrier (≤ ±6 kJ/mol) between activation energy and enthalpy changes, suggesting easy reaction initiation. Furthermore, variations in enthalpy (ΔH), Gibbs free energy (ΔG), and entropy (ΔS) upon conversion (α) suggest that peanut shell combustion is endothermic and non-spontaneous, with the generation of more homogeneous or well-ordered products as combustion progresses. These findings offer a theoretical basis and data support for the further utilization of agricultural biomass.

Wide bandgap semiconductors-based photocatalysts are usually limited by their low solar energy conversion efficiency due to their limited absorption solar wavelength, surface’s fast recombination of photoelectron–hole pairs and low charge-carrier mobility. Here we report a new stepwise solution synthesis for making a new photocatalytic core/shell of titanate nanowire/reduced graphene oxide shell (or titanate/rGO) 1D-nanocomposite. The new core/shell nanocomposite maximized the specific surface area, largely reduced the charge transfer resistance and reaction energy barrier, and significantly improved the absorption of the visible light. The core/shell nanocomposites’ large on/off current ratio and rapid photo-responses boosted the photocurrent by 30.0%, the photocatalysis rate by 50.0%, and the specific surface area by 16.4%, when comparing with the pure titanate nanowire core. Our numerical simulations support the effective charge separation on the new core-shell nanostructure, which can help further advance the new photocatalysis.

Pyrethroid pesticides (PYRs) as the third most widely used pesticides, following organophosphorus and carbamate pesticides, which are of significant importance in the analysis and detection of vegetables. However, the current pretreatment technology for PYRs confronts challenges of difficult separation and low enrichment efficiency, resulting in a cumbersome and time-consuming pretreatment process with poor selectivity. Here, a simple and efficient magnetic solid-phase extraction (MSPE) strategy was developed to simultaneously purify and enrich five PYRs in vegetables, with the magnetic covalent organic framework nanomaterial COF-SiO2@Fe3O4 as an adsorbent. The COF-SiO2@Fe3O4 was prepared by a simple solvothermal conditions method, using Fe3O4 as magnetic core, benzidine and 3,3,5,5-tetraaldehyde biphenyl as two building units. COF-SiO2@Fe3O4 could effectively capture the targeted PYRs by virtue of its abundant π-electron system and hydroxyl groups. The impact of various experimental parameters on extraction efficiency was investigated to optimize the MSPE conditions, including adsorbent amount, extraction time, elution solvent type and elution time. Subsequently, method validation was conducted under the optimal conditions in conjunction with gas chromatography-mass spectrometry (GC-MS). Within the range of 5.00–100 μg·kg-1 (1.00–100 μg·kg-1 for bifenthrin and 2.5–100 μg·kg-1 for fenpropathrin), the five PYRs exhibited a strong linear relationship, with determination coefficients ranging from 0.9990 to 0.9997. The limits of detection (LODs) were 0.3–1.5 μg·kg-1, and the limits of quantification (LOQs) were 0.9–4.5 μg·kg-1. The recoveries were 80.2–116.7% with relative standard deviations (RSDs) below 7.0%. Finally, COF-SiO2@Fe3O4, NH2-SiO2@Fe3O4 and Fe3O4 were compared as MSPE adsorbents for PYRs. The results indicated that COF-SiO2@Fe3O4 was an efficient and rapid selective adsorbent for PYRs. This method holds promising prospects for the determination of PYRs in real samples.

Background: Some viruses cause outbreaks which require immediate attention. Neutralizing antibodies could be developed for viral outbreak management. However, development of monoclonal antibodies is often long, laborious, and unprofitable. Here we report a Norwegian platform for development of chicken polyclonal neutralizing antibodies with powerful therapeutic potential. Methods: Layers were immunized twice with 14-day interval using purified RBD of SARS-CoV-2. Eggs were harvested 14 days after the second immunization. Polyclonal IgY antibodies were extracted. Binding of anti-RBD IgY to RBD was measured by indirect ELISA. Neutralization capacity of anti-RBD IgYs was measured in Vero-E6 cells infected with SARS-CoV-2-mCherry strain using fluorescence and cell viability assay. In addition, the effect of IgYs on the expression of SARS-CoV-2 and host cytokine genes in lungs of Syrian Golden hamsters was examined using qRT-PCR. Results: Anti-RBD IgYs efficiently bind RBD of S protein of SARS-CoV-2 in situ, neutralize the virus in vitro, and lower viral RNA amplification without significant alteration of virus-mediated immune gene expression in vivo. Conclusions: Altogether, our results indicated that chicken polyclonal IgYs can be attractive targets for pre-clinical and clinical development for rapid management of outbreaks of emerging and re-emerging viruses.

Soft magnetic composites cores were produced by Spark Plasma Sintering (SPS) from Ni3Fe@ZnFe2O4 and NiFeMo@ZnFe2O4 pseudo-core-shell powders. In the Fe-Ni alloys@ZnFe2O4 pseudo-core-shell composite powders, the core is a large nanocrystalline Permalloy or Supermalloy particle obtained by mechanical alloying, and the shell is a pseudo continuously layer of Zn ferrite particles. The pseudo-core-shell powders have been compacted by SPS at temperatures between 500-700 ºC, with a holding time of 0 minutes. Several techniques were used for the characterisation of the powders and sintered compacts: X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, magnetic hysteresis measurements (DC and AC) and electrical resistivity. The electrical resistivity is stabilised at values of about 7·10-3 Ω·m for sintering temperatures between 600-700 °C and this value is 3 orders of magnitude higher than the electrical resistivity of sintered Fe compacts. The best relative initial permeability was obtained for the Supermalloy/ZnFe2O4 composite compacts sintered at 600 ºC, which decreases linearly for the entire frequency range studied, from around 95 to 50. Up a frequency of 2,000 Hz the power losses are lower than 1.5 W/kg. At the frequency of 10 kHz, the power losses are larger, but they remain at a low level. In the case of Supermalloy/ZnFe2O4 composite compact SPS-ed at 700 °C, the specific power losses are even lower than 5 W/kg. The power losses decomposition proved that intra-particles losses give the main part of the losses.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

Industry 4.0 (I4.0) epitomizes the nexus of technological evolution and manufacturing process enhancements, underpinned by four critical pillars: Cyber-Physical Systems (CPS), Digital Twins (DT), the Industrial Internet of Things (IIoT), and Cloud Computing (CC). Through the lens of the German Reference Architectural Model Industrie (RAMI) 4.0, these components are integral to fostering Smart Manufacturing (SM) practices. In conjunction, the Asset Administration Shell (AAS) facilitates seamless inter-company communication and enables adaptability to fluctuating market demands. This paper delves into the structural intricacies of AAS and SM within the RAMI 4.0 framework, unveiling three distinct implementation strategies. Furthermore, it meticulously scrutinizes challenges that hinder the full realization of I4.0 potential, such as interoperability, security concerns, and standardized communication protocols. By examining these models and identifying current barriers, the study illuminates pathways for future research, particularly in enhancing the integration of AAS and SM systems, ensuring robust security measures, and advocating for the development of universal standards. This exploration aims to contribute to the ongoing discourse on I4.0, proposing avenues for advancing manufacturing technologies and operational frameworks in alignment with the principles of RAMI 4.0.

A new class of nano-cube core-shell heterostructures containing Ag coating on the top of WO₃ was fabricated. Physical vapor deposition was used to produce WO₃ based nano-heterostructures. All kind of wet toxic chemical process was avoided to make the process simple and contaminant free. Sputtering of WO₃ and a subsequent thermal annealing process was done to create nano-cubes of WO₃. After that, sputtering of Ag was performed to form the Ag-WO₃ core-shell nano-heterostructures (CSNH). The CSNHs were characterized using field emission scanning electron microscopy (FESEM), energy dispersive spectroscopy (EDS), X-ray diffraction analysis (XRD) and UV-vis spectroscopy. The morphologies, elemental analysis, interfaces, crystallinity, phases, and chemical compositions were analyzed. The bottom-up growth of WO₃ nanocubes was studied using different time periods at 900°C. Ag coating was also studied before and after annealing. Finally, an optical property (band gap) was also analyzed using Tauc plot derive from absorption spectra. The tailoring the band gap of WO₃ from ~2.9eV to ~ 2.45 eV was observed while Ag-WO₃ CSNH formed.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

With the burgeoning growth of online retail, the issue of counterfeit products has become a significant threat to both consumer trust and brand integrity, posing challenges to sustainable market practices. Online retail platforms are promoted to redesign their channel structures and enhance brand traceability to tackle counterfeits using blockchain technology. To investigate the interactions between blockchain technology and the channel structures of online retail platforms, we design a game theory model incorporating a manufacturer with(out) blockchain participation selling products via an online retail platform that operates an agency channel and/or a reselling channel. We show that the critical trade-off of blockchain participation comprises the brand assurance effect of the blockchain, the channel competition intensification effect, and the blockchain adoption cost. The platform is capable of strategically designing the channel structure to encourage (while discouraging) blockchain participation by the manufacturer. Our analysis highlights the complementarity between blockchain participation and the channel structure. Furthermore, the effect of the consumer’s belief in the reselling channel, the commission fee in the agency channel, and the substitutability between channels are investigated in depth. The research provides valuable insights for online retail platforms and policymakers seeking to foster a sustainable and trustworthy e-commerce ecosystem.

Waterbomb structures are origami-inspired deformable structural components used in new types of robots. They have a unique radially deployable ability that enables robots to better adapt to their environment. In this paper, we propose a series of new waterbomb structures with square, rectangle, and parallelogram base units. Through quasi-static axial and radial compression experiments and numerical simulations, we prove that the parallelogram waterbomb structure has a twist displacement mode along the axial direction. Compared with the square waterbomb structure, the proposed optimal design of the parallelogram waterbomb structure reduces the critical axial buckling load-to-weight ratio by 55.4% and increases the radial stiffness-to-weight ratio by 67.6%. The significant increase in the radial stiffness-to-weight ratio of the waterbomb structure and decrease in the critical axial buckling load-to-weight ratio make the proposed origami pattern attractive for practical robotics applications.

Hazelnut shells (HS), scientifically known as Corylus avellana L. shells, are a waste produced in companies that process nuts. The main objective of this study was to find an efficient way to maximize the chemical potential of HS by solubilizing the hemicelluloses, which could then be used to recover sugars and at the same time increase the lignin content of this material in order to produce adhesives or high strength foams. In order to optimize the pre-hydrolysis process, two different temperatures (160 and 170 C) and times varying from 15 to 180 min were tested. All the remaining solid materials were then liquefied by polyalcohols with acid catalysis. The chemical composition of hazelnut shells was determined before and after the pre-hydrolysis. All the process was monitored by FTIR-ATR by determining the spectra of solids and liquids after pre-hydrolisis and liquefactions steps. The highest solubilization of hazelnut shells was found for 170 C and 180 min, resulting in a 25.8% solubilization. Chemical analysis after the hydrolysis process showed a gradual increase in the solubilization of hemicelluloses as both the temperature and time of the reactor were increased. Simultaneously, the percentages of α-cellulose and lignin in the material also increased with rises in temperature and duration. FTIR-ATR allowed for the detection of significant spectral changes in the hazelnut shells from their initial state to the solid residue and further into the liquefied phase. This confirmed that pre-hydrolysis was effective in enhancing the chemical composition of the material, making it more suitable for the production of adhesives or polyurethane foams with enhanced mechanical strength.

In this work, we introduce the first pipeline that combines a refraction-aware Structure-from-Motion (SfM) method with a deep learning model specifically designed for airborne bathymetry. We accurately estimate the 3D positions of the submerged points by integrating refraction geometry within the SfM optimization problem. This way, no refraction correction as post-processing is required. Experiments with simulated data that approach the real-world capturing conditions demonstrate that SfM with refraction correction is extremely accurate, with submillimeter errors. We integrate our refraction-aware SfM within a deep learning framework that also takes into account radiometrical information, developing a combined spectral and geometry-based approach, with further improvements on accuracy and robustness to different seafloor types, both textured and textureless. We conducted experiments with real-world data at 2 locations in the southern Mediterranean Sea, with varying seafloor types which demonstrate the benefits of refraction correction for the deep learning framework. We open-source our refraction-aware SfM, providing researchers in airborne bathymetry with a practical tool to apply SfM in shallow water areas.

By using the particle swarm optimization algorithm for crystal structure prediction, we reveal a newly orthorhombic Cmcm structure of HfB4, which is more energetically superior to the previously proposed YB4-, ReP4-, FeB4-, CrB4-, and MnB4-type structures in the considered pressure range. The phonon dispersion and elastic constants calculations confirm that the new phase is dynamically and mechanically stable. The calculated large shear modulus (240 GPa) and high hardness (45.7 GPa) imply that the predicted Cmcm-HfB4 is a potential superhard material. Meanwhile, the directional dependences of the Young's modulus, bulk modulus, and shear modulus for HfB4 are systematically investigated. Further analyses of the density of states and electronic localization function indicate that the strong B-B and B-Hf covalent bonds greatly contribute to its high hardness and stability.

The SK model proposed by Sherrington and Kirkpatrick is an important mean field model for spin glasses. The dependence structure of Hamiltonians of the SK model is considered in this paper. We have investigated the covariance matrix of Hamiltonians of the SK model, and establish a relationship between the rank of the corresponding covariance matrix and the dimension of the space spanned by the Hamiltonians. Finally, we also give an upper bound for the rank of the covariance matrix, which might be the best.

This paper seeks to fill in the gaps of modern relativistic Cosmology by utilizing the total symmetry between space and time dimensions and re-interpreting the scale factor of the Universe as a gravitational potential generated by the mass/energy of the entire Universe as a whole. The gradient of this potential is along the cosmological time dimension through which the Universe is falling. This gradient gives us an arrow of time, we find explanations for why the Universe began expanding and why the expansion is accelerating without the need for a Cosmological Constant. In a finite time, the gradient will point in the opposite direction of time turning the expanding Universe into a collapsing one where it is shown that when placing the Schwarzschild metric in the dynamic Cosmological background, gravity becomes repulsive and things like would-be Black Holes become White Holes. The model naturally describes a Universe and an anti-Universe (consisting of antimatter) moving in opposite directions of time that collide at the end of collapse, annihilating and subsequently pair producing two new Universes as the cycle begins again. It is shown that the model's Hubble diagram fits the currently available supernova and quasar data. It is found that Dark Matter can perhaps be understood as ordinary matter that is not connected to us with null geodesics.

Two novel core-shell composites SiO2@PMDA-Si-Tb, SiO2@PMDA-Si-Tb-phen with SiO2 as the core and terbium organic complex as the shell, were successfully synthesized. The terbium ion was coordinated with organic ligand forming terbium organic complex in the shell layer. The bi-functional organosilane ((HOOC)2C6H2(CONH(CH2)3Si(OCH2CH3)3)2 (abbreviated as PMDA-Si) was used as the first ligand and phen as the second ligand. Furthermore, the silica-modified SiO2@PMDA-Si-Tb@SiO2, SiO2@PMDA-Si-Tb-phen@SiO2 core-shell-shell composites were also synthesized by sol–gel chemical route. An amorphous silica shell was coated around the SiO2@PMDA-Si-Tb and SiO2@PMDA-Si-Tb-phen core-shell composites. The core-shell and core-shell-shell composites both exhibited excellent luminescence in solid state. The luminescence of core-shell-shell composites was stronger than that of core-shell composites. Meanwhile, an improved luminescence stability property for the core-shell-shell composites was found in the aqueous solution. The core-shell-shell composites exhibited bright luminescence, high stability, long lifetime, and good solubility, which may present potential applications in the field of bio-medical.

Estimating the ocean’s subsurface thermohaline information from satellite measurements is essential for understanding ocean dynamics and El Niño phenomenon. This paper proposes an improved double-output Residual Neural Network (DO-ResNet) model to concurrently estimate the ocean subsurface temperature (OST) and ocean subsurface salinity (OSS) in the tropical Western Pacific using multi-source remote sensing data, including sea surface temperature (SST), sea surface salinity (SSS), sea surface height anomaly(SSHA), sea surface wind (SSW), and geographical information (including longitude (LON) and latitude (LAT)). In the model experiment, Argo data were used to train and validate the model, and the root mean square error (RMSE), normalized root mean square error (NRMSE) and coefficient of determination (R²) were employed to evaluate the model's performance. The results showed that the sea surface parameters selected in this study have a positive effect on the estimation process, and the average RMSE and R² values for estimating OST (OSS) by the proposed model are 0.34 °C (0.05 psu) and 0.91 (0.95), respectively. Under the data conditions considered in this study, DO-ResNet demonstrates superior performance relative to the extreme gradient boosting model, random forest model, and artificial neural network model. Additionally, this study evaluates the model’s accuracy by comparing its estimations of OST and OSS across different depths with Argo-derived data, demonstrating the model's ability to effectively capture the most spatial features, and by comparing NRMSE across different depths and seasons, the model displays strong seasonal adaptability. In conclusion, this research introduces a novel artificial intelligence technique for estimating OST and OSS in the tropical Western Pacific Ocean.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

Effects and interactions of incubation time and chick preplacement holding time on mortality at placement, utilization of yolk sac, crop filling rate, early feeding–drinking behavior and broiler live performance were investigated. Ross 308 broiler hatching eggs from a 39-week-old flock were set in two identical setters in a commercial hatchery,with setting time 12 hours earlier in one machine. At the end of incubation, chicks were removed from the hatchers at the same time. Thus, incubation times were either 504 h (normal incubation time (NIT) treatment) or 516 h (longer incubation time (LIT) treatment). After pull time, chicks from each incubation time group were subjected to either 6, 24, 48, 60 or 72 h preplacement holding times. At placement, chicks were given access to feed and water. In total, 19,200 chicks were randomly assigned to a total of 10 subtreatment groups (2 incubation times × 5 preplacement holding times). Therefore, a total of 1,920 chicks were used in each subtreatment group for the grow-out period in a commercial broiler house. An interaction was found between incubation time and preplacement holding time for residual yolk sac (RYS) weight (g, %) (p < 0.001). RYS weight was greater at pull time and at 6 and 24 h of preplacement holding time in the NIT treatment compared to the LIT treatment, while differences were no longer evident at 48–72 h. The lowest percentage of chicks with full crops and eating activity was observed in the shortest preplacement holding time (6 h) group at 3 h after placement. As expected, the initial BW at placement clearly decreased with increasing duration after the pull time (p < 0.05) with the highest and lowest weights were found in the 6 and 72 h holding time treatments respectively. This BW difference was still evident at 35 d after placement and chicks held for the longest period after the pull time (72 h) showed the lowest BW (p < 0.001). However, there was no significant difference between the 6 and 60 h preplacement holding times. Mortality during the first 7 d after placement increased only when the preplacement holding time was extended to 72 h (p = 0.031). Similar to the 7 d results, chicks held for 72 h exhibited higher 0-35 day mortality compared to those held for 6 or 24 h (p = 0.028). Neither BW nor mortality was affected by incubation time treatment at 35 d after placement (p > 0.05). It can be concluded that there were no significant differences in average BW and mortality, up to and including a 60-h holding time under thermal comfort conditions, but a 72-h preplacement holding time resulted in final BW and mortality being negatively affected. In addition, LIT tended to have a beneficial effect on BW and mortality compared to NIT when the preplacement holding time was shorter (6–24 h) but had a negative effect for extended holding times (48–72 h).

Floral nectar is a key reward in Leguminosae despite the exceptional diversity of flowers in this family. The paper aims to summarize the available data on structure, ontogeny, regulation, and possible evolution of the leguminous floral nectaries. To date, detailed characterization of ultrastructure and mode of secretion is available only for a few representative of the family whereas the majority remains understudied from this perspective. In most cases, regardless of flower symmetry, nectaries are localized between stamens and a carpel. The nectar is usually exuded from modified stomata although the exact mode of secretion by specialized parenchyma may differ between taxa. The leguminous floral nectaries often have certain features of monosymmetry with preferentially abaxial development. Nectaries were independently lost in several lineages, and equally recurrent is the emergence of substitutive, i.e. evolutionary innovative, nectar-producing structures. Floral nectaries possess a certain degree of evolutionary inertia, i.e. they remain stable even in lineages in which flower morphology underwent significant changes compared with an ancestral plan, such as shifts in merism, symmetry, organ number and alike. Due to their evolutionary stability, floral nectaries are rarely used in taxonomy of Leguminosae.

The catenary shells of revolution are widely used in constructions due to their unique mechanics' feature. However, no publications on this type of shells can be found in the literature. To have a better understanding of the deformation and stress of the catenary shells of revolution, we formulate the principal radii for two kinds of catenary shells of revolution and their displacement type governing equations. Numerical simulations are carried out based on both Reissner-Meissner mixed formulations and displacement formulations. Our investigations show that both deformation and stress response of elastic catenary shells of revolution are sensitive to its geometric parameter $c$, and reveal that the mechanics of the catenary shells of revolution does much better than the spherical shells. Two complete codes in Maple are provided.

The versatile one-pot green synthesis of a highly concentrated and stable colloidal dispersion of AgNPs was carried out using the self-assembled tannic acid without using any other hazardous chemicals. Tannic acid (Plant-based polyphenol) was used as a reducing and stabilizing agent for silver nitrate in a mild alkaline condition. The synthesized AgNPs were characterized for their concentration, capping, size distribution, and shape. The experimental results confirmed the successful synthesis of nearly spherical and highly concentrated (2281 ppm) AgNPs, capped with poly-tannic acid (AgNPs-PTA). The average particle size of AgNPs-PTA was found 9.90 ± 1.60 nm. The colloidal dispersion of synthesized nanoparticles was observed stable for more than 15 months in the ambient environment (25 oC, 65 % relative humidity). The synthesized AgNPs-PTA showed an effective antimicrobial activity against Staphylococcus Aureus Escherichia coli. Ag-PTA also exhibited enhanced catalytic properties. It reduces 4-nitrophenol into 4-aminophenol in the presence of NaBH4 with a normalized rate constant (Knor = K/m) of 615.04 mL·s-1·mg-1. Furthermore, AgNPs-PTA were stable for more than 15 months under ambient conditions. The unique core-shell structure and ease of synthesis render the synthesized nanoparticles superior to others, with potential for large-scale applications, especially in the field of catalysis and biomedical.

The attitude dynamics and orbit dynamics of large rigid space structures are coupled with each other under gravity gradient, which may affect the stability of the large rigid space structures. In this paper, the gravity gradient stability of a large rigid space structure is studied under both small and large disturbances. Based on the rigid body dynamics and orbit dynamics, an accurate dynamic model without any linearization of the large rigid space structure is established via the natural coordinate formulation (NCF), which is able to describe the large overall motions of the structures. By using the generalized-α algorithm, the gravity gradient stability of the large rigid space structure is simulated and analyzed via various examples, including the influence of large disturbance angles, the positions at the stabilization and unstabilization regions. Finally, the relationship between spinning stability and gravity gradient stability is also investigated via a large spinning space structure.

The present work investigates primarily the morphology evolution of the body-centered-cubic (BCC)/B2 phases in AlxNiCoFeCr high-entropy alloys (HEAs) with increasing Al content, which has been neglected so far. There exist two types of microscopic morphologies of BCC and B2 phases in this HEA series: one is the weave-like morphology induced by the spinodal decomposition, and the other is the microstructure of a spherical disordered BCC precipitation on the ordered B2 matrix that appears in HEAs with a much higher Al content. The shape of coherent precipitates is found to be closely related to the lattice misfit between BCC and B2 phases, which is sensitive to Al. The mechanical properties, including the compressive yielding strength and microhardness of the AlxNiCoFeCr HEAs, are also discussed in light of the concept of the valence electron concentration (VEC).

Lignin is insoluble in water, limiting its use in the synthesis of adhesives. Therefore, in order to increase the amount of lignin raw materials used in the synthesis of adhesives, a kind of aminated lignin compounds was prepared through lignin amination reaction, and conducting structural analysis in this paper. The particle size of the amino lignin is about 100 nm, with the weight average molecular weight of 57,627 g/mol and a water solubility of 0.45g/100ml. The reaction mechanisms were proposed that the phenolic hydroxyl groups of lignin react with ammonia molecules, and thereby successfully introducing amino groups to generate the aminated lignin compounds. Therefore, this article enriches the scientific theory of lignin reactions and provides reference for the widespread application of lignin raw materials in the field of adhesives.

Knowledge is not merely the characteristic of certain pieces of information being deemed true and justifiable, but rather a process. Within an axiomatic system, the set of information that reaches the status of knowledge forms a universe that provides an interpretation of the reality one aims to describe. Language exchanges information through communication and the process of justification (exchange of information), if it consistently justifies a particular piece of information, it elevates it to knowledge. In this paper, we provide a framework for knowledge within an axiomatic model where we define the fundamental elements of communication and grammar. As a result, the structure dictates that knowledge, to be considered as such, must be investigateable by anyone who utilizes it in its entirety, both in form and content. Ultimately, the development of knowledge processing, referred to as \emph{knowmatics}, represents a clear evolution of the computer science that processes information (subset of knowledge).

Prunus dulcis is one of the most widely cultivated species in the world. Its fruit (almond) is rich in various nutritious and bioactive compounds that exert several beneficial effects. The aim of this study was to determine the chemical profile and evaluate the biological potential in vitro of almond shell extracts. The chemical analysis of shell extracts led to the identification of 15 com-pounds by HPLC-DAD of which 11 were first detected in the almond plant. Twenty-six volatile compounds were identified by the GC-MS technique, among them; seven were firstly detected in the studied plant. For the biological activities, the extracts demonstrated moderate inhibition potential against the antioxidant, antidiabetic, and cytotoxic activities. The methanol extract at 50 µg/mL showed the highest antioxidant (45%) and antidiabetic activities (45% against alpha-glucosidase and 31% against alpha-amylase extracts), while the cyclohexane and dichloromethane at 50 µg/mL showed the highest cytotoxic activity towards Hela (32.2% with cyclohexane), and RAW 264-7 (45% with dichloromethane). Overall, these findings demonstrate the potential of almond shell extracts as a source of bioactive compounds that could be applied in the pharmaceutical and medical fields.

In this study we have investigated the effect of the addition of Nb2O5 (up to 5 mol%) on the structure and luminescent properties of ZnO-B2O3 glass doped with 0.5 mol % Eu2O3 by using of infrared (IR), Raman and photoluminescence (PL) spectroscopy. Physical properties as molar volume, oxygen packing density and glass transition temperature were determined using the results of differential thermal analyisis (DTA) and Archimedes principle for density. IR and Raman spectra revealed that niobium ions incorporate into the base zinc borate glass as NbO4 trtraherda and NbO6 octahedra. A strong red emission from the 5D0 level of Eu3+ ions was registered under near UV (392 nm) excitation using the sharp 7F0 - 5L6 transition of Eu3+. The integrated fluorescence intensity ratio R (5D0 → 7F2/5D0 → 7F1) was calculated to estimate the degree of asymmetry around the active ion, suggesting a location of Eu3+ in non-centrosymmetric sites. The higher Еu3+ luminescence emission observed in zinc borate glasses containing 1÷5 mol% Nb2O5 compared to the Nb2O5-free zinc borate glass evidences that Nb2O5 is suitable component for modification of host glass structure and improving the emission intensity.

The atomic structures of Zn and Na borophosphate glasses were studied by X-ray and neutron diffraction. Peaks assigned to the B−O, P−O, and O−O distances confirm that only BO4 units co-exist with the PO4 tetrahedra. The Zn−O and Na−O coordination numbers are found to be a little larger than four. The narrowest peaks of the Zn−O first-neighbor distances exist for the glasses along a line connecting the Zn(PO3)2 and BPO4 compositions (50 mol% P2O5) which is explained by networks of ZnO4, BO4, and PO4 tetrahedra with twofold coordinated oxygens. Calculated amounts of the available oxygen support this interpretation. Broadened peaks occur for glasses with lower P2O5 contents, consistent with the presence of threefold coordinated oxygens. The two distinct P−O peak components of the Zn and Na borophosphate glasses differ in their relative abundances which is interpreted by Na+ cations that coordinate oxygens in some P−O−B bridges, something not seen for the Zn2+ ions.

This study investigates the potential of utilizing hazelnut shells (HS) as an innovative filler in three-layer plywood technology, addressing the growing need for sustainable, high-performance materials. Traditional plywood production relies on adhesives enhanced with various fillers to improve physical, mechanical, and operational characteristics. This research explores using native, chemically modified, and activated carbon derived from hazelnut shells as fillers in urea-formaldehyde (UF) resin. The mechanical properties, water absorption, and formaldehyde emissions of the produced plywood were thoroughly analyzed. Key findings demonstrate that incorporating 10 part by weight (pbw) native hazelnut shell flour significantly enhances the modulus of rupture (MOR) and modulus of elasticity (MOE). Chemically modified hazelnut shell flour achieves optimal results at 5 pbw, while activated carbon from hazelnut shells, even at 1 pbw, markedly improves bonding strength and thermal properties. Notably, activated carbon effectively reduces formaldehyde emissions and improves water resistance, indicating better further dimensional stability and lower environmental impact. The study also shows that excessive filler content negatively affects strength parameters, confirming the importance of optimizing filler concentration. These results highlight the potential of hazelnut shells as an eco-friendly alternative filler in plywood production, contributing to waste valorization and environmental sustainability. This study supports the practical application of hazelnut shell fillers, promoting a circular economy and reducing reliance on traditional, less sustainable materials, thus providing a valuable solution for the wood composite industry.

High-spin states of 192Tl are populated by the heavy ion fusion-evaporation reaction 181Ta(16O, 5n)192Tl at 97 MeV beam energy. A new level scheme with eight new levels is constructed and the level spins are tentatively assigned. The negative-parity yrast band is extended up to 23^{-}\hbar. Subsequently, the systematics of signature splitting and signature inversion are discussed for the negative-parity yrast band of odd-odd Tl isotopes including 192Tl, 194Tl, 196Tl, and 198Tl. With the increase of neutron number signature inversion is found in 196,198Tl at high-spin state in these four Tl isotopes. The reason may be due to the competition between neutron-proton interaction and Coriolis force.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

Background: Molecular genetic events are among the numerous factors affecting the clinical course of papillary thyroid carcinoma (PTC). Recent studies have demonstrated that aberrant expression of miRNA, as well as different thyroid-related genes, correlate with the aggressive clinical course of PTC and unfavorable treatment outcome, which opens up new avenues for using them in personalization of the treatment strategy for patients with PTC. In the present work, our goal was to assess the applicability of molecular markers in preoperative diagnosis of aggressive variants of papillary thyroid cancer. Methods: The molecular genetic profile (expression levels of 34 different markers and BRAF mutation) was studied for 108 cytology specimens collected by fine-needle aspiration biopsy in patients with PTC having different clinical manifestations. Results: Statistically significant differences with adjustment for multiple comparisons (p < 0.0015) for clinically aggressive variants of PTC were obtained for four markers: miRNA-146b, miRNA-221, FN1, and CDKN2A. Weak statistical correlation (0.0015< р<0.05) was observed for miRNA-31, -375, -551b, -148b, -125b, mtDNA, CITED1, TPO, HMGA2, CLU, NIS, SERPINA1, TFF3, and TMPRSS4. Conclusions: The recurrence risk of papillary thyroid carcinoma can be preoperatively predicted using miRNA-221, the fibronectin and cyclin-dependent kinase inhibitor 2A genes.

The dielectric constant (ε) reflects the ability of a material to align and orient electrical dipoles within its structure in response to an externally applied electric field; the greater the polarizability of molecules, the greater the value of dielectric constant. In this study a data set of 86 polymers was investigated to develop a structure-property quantitative relations (QSPR) model to predict the dielectric constant in polymers. An initial set of 1273 descriptors was used to select a best set of descriptors and to construct two machine learning models with Gradient Boosting Regressor (GB_A and GB_B). The best performing model (GB_A) with 8 descriptors, exhibited a performance of (R2train) = 0.938 and (R2test) = 0.802. The models were internally validated by 5 folds cross-validation, demonstrating robustness. Additionally, using the Accumulative Local Effect (ALE) technique, we analyzed the relationship between the 8 descriptors involved and the impact of these descriptors to dielectric constant of polymers.

The advancement in science and technology has led to luffa sponge (LS) being widely used as a natural material in industrial application as its polyporous structure and light texture. In order to enhance the utility of LS fibers as the reinforcement of lightweight composite materials, this study investigate its water absorption, mechanical properties, anatomical characteristic and thermal performance. Hence, moisture regain, tensile properties of LS fiber bundles were measured in accordance with standards and the structural characteristics were investigated via microscopic observation. Scanning electron microscopy (SEM) was used to observe the surface morphology and fracture surface of fiber bundles. Test results shows that the special structure where the phloem tissues degenerate to cavities had a significant influence on the mechanical properties of LS fiber bundles. Additionally, the transverse sectional area occupied by fibers in a fiber bundle (SF), wall thickness and ratio of wall to lumen of fiber cell, and crystallinity of cellulose had an impact on the mechanical properties of LS fiber bundles. Furthermore, the fiber bundles density of LS varies range of 385.46-468.70 kg/m³, much less than that of jute (1360.40 kg/m³) and Arenga engleri (950.20 kg/m³) while LS fiber bundles has superior specific modulus.

In the present paper, the comparison is conducted between three classical shell theories as applied to the linear vibrations of single-walled carbon nanotubes (SWCNTs); specifically, the evaluation of the natural frequencies is conducted via Donnell, Sanders and Flügge shell theories. The actual discrete SWCNT is modelled by means of a continuous homogeneous cylindrical shell considering equivalent thickness and surface density. In order to take into account the intrinsic chirality of carbon nanotubes (CNTs), a molecular based anisotropic elastic shell model is considered. Simply supported boundary conditions are imposed and complex method is applied to solve the equations of motion and to obtain the natural frequencies. Comparisons with the results of molecular dynamics simulations available in literature are performed to check the accuracy of the three different shell theories, where Flügge shell theory is found to be the most accurate. Then, a parametric analysis evaluating the effect of diameter, aspect ratio and number of waves along the longitudinal and circumferential directions on the natural frequencies of SWCNTs is performed in the framework of the three different shell theories. Assuming the results of Flügge shell theory as references, it is obtained that Donnell shell theory is not accurate for relatively low longitudinal and circumferential wavenumbers, for relatively low diameters and for relatively high aspect ratios. On the other hand, it is obtained that Sanders shell theory is very accurate for all the considered geometries and wavenumbers, and therefore it can be correctly adopted instead of the more complex Flügge shell theory for the vibration modelling of SWCNTs.

The extracellular matrix (ECM) plays a key role as both structural scaffold and regulator of cell signal transduction in tissues. In times of ECM assembly and turnover, cells upregulate assembly of the ECM protein, fibronectin (FN). FN is assembled by cells into viscoelastic fibrils that can bind upward of 40 distinct growth factors and cytokines. These fibrils play a key role in assembling a provisional ECM during embryonic development and wound healing. Fibril assembly is also often upregulated during disease states, including cancer and fibrotic diseases. FN fibrils have unique mechanical properties, which allow them to alter mechanotransduction signals sensed and relayed by cells. Binding of soluble growth factors to FN fibrils alters signal transduction from these proteins, while binding of other ECM proteins, including collagens, elastins, and proteoglycans, to FN fibrils facilitates the maturation and tissue specificity of the ECM. In this review, we will discuss the assembly of FN fibrils from individual FN molecules; the composition, structure, and mechanics of FN fibrils; the interaction of FN fibrils with other ECM proteins and growth factors; the role of FN in transmitting mechanobiology signaling events; and approaches for studying the mechanics of FN fibrils.

Recently, some authors have developed a shell-less culture system for chick embryos by using a plastic lm as culture vessels. We will show that velocity of rotation of vessels in incubator and temperature have direct relations with growth of chick embryos. We also obtain a mathematical relation between velocity, temperature and rate of growth of chick embryo.

In recent decades, the requirements for implantable medical devices increased, but the risks of implant rejection still exist. These issues are primarily associated with poor osseointegration, leading to biofilm formation on the implant surface. This study focuses on addressing these issues by developing a biomaterial for implant coatings. 45S5 Bioglass has been widely used in tissue engineering due to its ability to form a hydroxyapatite layer, ensuring a strong bond between the hard tissue and the bioglass. In this context, 45S5 bioglasses, modified by the incorporation of different amounts of copper oxide, from 0 to 8 mol%, were synthesized by the melt-quenching technique. The incorporation of Cu ions does not show a significant change in the glass structure. Since the bioglass exhibited the capacity of being polarized, and therefore promoting the osseointegration effectiveness, the electrical properties of the prepared samples were studied using the impedance spectroscopy method, in the frequency range of 102-106 Hz and temperature range of 200-400 K. The effects of CuO on charge transport mobility were investigated. Additionally, the bioactivity of the modified bioglasses was evaluated through immersion tests in simulated body fluid. The results revealed the initiation of a Ca-P-rich layer formation on the surface within 24 h, indicating the potential of the bioglasses to enhance the bone regeneration process.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

This letter presents a dual-frequency terahertz amplitude modulator based on a cross-shaped structure and U-shaped metal patches. Its structural unit is a typical metal-substrate structure. The top metal consists of a cross-shaped structure and U-shaped metal patches, and the bottom substrate layer is made of quartz. Amplitude modulation is achieved by adjusting the temperature of the vanadium dioxide (VO2) patches. The modulation depth can be approximately 75%. The mechanism of the resonance frequency is explained by the equivalent circuit model. The proposed structure shows good amplitude modulation capability at different incidence and azimuth angles by changing the location of the VO2 patches. The dual-frequency terahertz amplitude modulator can be used in terahertz communication, imaging, etc.

The nucleon-pair shell model (NPSM) with broken symmetry basis is studied. The results demonstrate the validity of NPSM with symmetry broken basis, which leads to a significant reduction in the dimensionality of the multi-pair configuration space. We have observed that the axial-deformed basis provides a satisfactory description of the low-lying spectrum, even without the need for the projection procedure. In the case of the triaxial-deformed basis, we have investigated the variation after angular momentum projection, indicating the potential for NPSM to find exact solutions in the half-closed system.

Low-energy Coulomb excitation is capable of providing unique information on static electromagnetic moments of short-lived excited nuclear states, including non-yrast states. The process selectively populates low-lying collective states and is therefore ideally suited to study phenomena such as shape coexistence and development of exotic deformation (triaxial or octupole shapes). Historically, these experiments were restricted to stable isotopes. However, the advent of new facilities providing intense beams of short-lived radioactive species has opened the possibility to apply this powerful technique to a much wider range of nuclei. We discuss the observables that can be measured in a Coulomb-excitation experiment, their relation to nuclear structure parameters with an emphasis on the nuclear shape, and present some recent examples of Coulomb-excitation studies that provided outcomes relevant for the Shell Model.

To clarify effects of weathered coal humic acid on water-stable aggregates and pore characteristics of reclaimed cambisol, this research analyzed the evolution characteristics of soil aggregates and pores. Effects of different humic acid dosages (0, 1%, 3%, and 5% by weight) and application period (1 year, 2 years, and 3 years) on soil aggregates and organic carbon components in soil water-stable aggregates were investigated. The results showed that water-stable macroaggregates (>0.25 mm) had the highest content in the first year; but in the third year, water-stable microaggregates (0.053–0.25 mm) had the highest content, and silt and clay (<0.053 mm) were at a maximum. In the third year of 5% treatment, mean weight and geometric mean diameters were the largest, soil structure was the most stable, and TOC and water-stable microaggregates (0.053–0.25 mm) in soil had the highest proportions. For 5% treatment, the majority of irregular pores were independent in the first year, and number of pores decreased in the second year, but average pore volume increased, forming robust connected pores. In the third year, the number of elongated and irregular pores increased. In the third year of 5% treatment, most pores were irregular and of size >100 μm, and soil structure was the most stable.

In this paper, the synthesis of two novel luminescent Eu3+ ion complexes [Eu(TFT)3(phen) (1) and Eu(TFT)3(bpy)•Hex (2)] based on the combination of 2-(2,2,2-trifluoroethyl)-1-tetralone (TFT), containing n-donor ligands (1,10-phenanthroline or 2,2'-Bipyridine) and Eu3+ ion is reported herein, and their structural features are discussed on the basis of X-ray crystallographic and thermal analyses. We observed that the ligands transfer energy effectively to the metal center by fluorescence, IR and UV spectrograms studies. The structures and properties of complexes 1-2 were optimized by the DFT theoretical calculation, and the calculation results were consistent with the experimental X-ray structure data and spectral analysis.

Most of the mid-high permeability sandstone oilfields in China have entered the ultra-high water cut stage, accompanied with the highly-dispersed residual oil, and the control effect of mi-cro-heterogeneity on the residual oil is increasingly prominent. Understanding the microscopic characteristics of pore structural and its evolution during the long-term waterflooding is critical for enhancing the accuracy and efficiency of oil field exploitation. While the previous insights paid more attention to the geometrical and morphological features of pore structure and ignores the relation of pore structure with the fluid flow capacity. In this study, we propose a microscopic pore structure classification method considering pore size and local permeable capacity, which realizes the physical classification and quantitative evaluation of pore structure characteristics for different permeability rocks. The micro-pore structure is classified into 6 types based on the key evaluation parameters of pore diameter and flow flux area. By taking six mid-high permea-bility sandstone core samples from Daqing oilfield in China, a series of long-term waterflooding experiments are carried out and the interior pore structure was captured using high precision CT scanning technique. The results reveals that high-permeability reservoirs exhibit concentrated pores diameters and finer throats, whereas mid-permeability reservoirs exhibit smaller pores and throats in greater quantity. With the increase of water injection volumes, the permeable ca-pacity and connectivity of the high-connectivity pore space in ultra-high- and high-permeability reservoirs are enhanced, and in mid-permeability reservoirs, the micro-heterogeneity intensifies the increase in low-connectivity small pores. These findings provide new insights for the micro-scopic heterogeneity and a solid theoretical basis for investigating the occurrence of microscopic residual oil and optimising enhanced oil recovery strategies at the late stage of ultra-high water cut.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Leakage is important in groundwater cycle research and water resource management, the key is to construct the spatial distribution of aquitard. Influenced by natural and anthropogenic factors, the density of boreholes restricts the accuracy of aquitard structure. This paper explores the K-Nearest Neighbor (KNN) method to construct multi-layer aquitard structure in the hinterland of Songnen Plain, Northeast China, with limited boreholes, and compare it with Inverse Distance Weight (IDW) and Ordinary Kriging (OK) methods to evaluate the leakage. The KNN needs to first identify the eigenvalue-k of each layer, which is used to enhance the trainset to obtain the testset with a larger amount of sample data enhanced, and to make a prediction to obtain the 3-dimensional structure of aquitard. KNN is more accurate than the IDW and OK. The aquitrad structure obtained by the KNN is different from the IDW and OK, the thickness difference is 3.53%-54.00%, the area difference is 2.28%-23.91%, and the difference in leakage can be up to 24.51%. KNN also has a high degree of identification of aquitard edges, which can help the prevention of groundwater pollution. The results provide guidance for water balance analysis, borehole engineering design, water resources management and exploitation.

Arabinoxylans (AXs) are non-starch polysaccharides with complex structures naturally occurring in grains (i.e., barley, corn, and others) providing many health benefits, especially as prebiotics. AXs can be classified as water-extractable (WEAX) and water-unextractable (WUAX) based on their solubility, with properties influenced by grain sources and extraction methods. A large body of evidence shows that AXs exert an im-portant health impact, including glucose and lipid metabolism regulation and immune system enhancement, which is induced by the interactions between AXs and the gut microbiota. Recent research underscores the dependence of AX physiological effects on structure, advocating for a deeper understanding of struc-ture-activity relationships. While systematic studies on WEAX are prevalent, knowledge gaps persist re-garding WUAX, despite its higher grain abundance. Thus, this review reports recent data on WUAX struc-tural properties (chemical structure, branching, MW) in cereals under different treatments. It discusses WUAX applications in baking and its benefits deriving from gut fermentation.

Flexible wearable pressure sensors offer numerous benefits, including superior sensing capabilities, a lightweight and compact design, and exceptional conformal properties, making them highly sought after in various applications including medical monitoring, human-computer interaction, and electronic skin. Because of their excellent characteristics, such as simple fabrication, low power consumption, and short response time, capacitive pressure sensors have received widespread attention. As a flexible polymer material, polydimethylsiloxane (PDMS) is widely used in the preparation of dielectric layers for capacitive pressure sensors. The Young's modulus of the flexible polymer can be effectively decreased through the synergistic application of sacrificial template and laser ablation techniques, thereby improving the functionality of capacitive pressure sensors. In this study, a novel sensor was developed through a series of processes including sacrificial template method using NaCl microparticles, CO₂ laser ablation, and sandwiching a porous PDMS dielectric layer between two flexible electrodes to create a capacitive pressure sensor. The sensor demonstrates a sensitivity of 0.694 kPa-1 within the pressure range of 0-1 kPa, and can effectively detect pressures ranging from 3 Pa to 200 kPa. The sensor demonstrates stability for up to 500 cycles, with a rapid response time of 96ms and a recovery time of 118ms, coupled with a low hysteresis of 6.8%. Furthermore, our testing indicates that the sensor possesses limitless potential for use in detecting human physiological activities and signaling emergencies.

Metal nanoparticles are used to modify/enhance the properties of a polymer matrix for a broad range of applications in bio-nanotechnology. Here, we study the properties of polymer/gold nanoparticle (NP) nanocomposites through atomistic molecular dynamics, MD, simulations. We probe the structural, conformational and dynamical properties of polymer chains at the vicinity of a gold (Au) NP and a functionalized (core/shell) Au NP, and compare them against the behavior of bulk PE. The bare Au NPs were constructed via a systematic methodology starting from ab-initio calculations and an atomistic Wulff construction algorithm resulting in the crystal shape with the minimum surface energy. For the functionalized NPs the interactions between gold atoms and chemically adsorbed functional groups change their shape. As a model polymer matrix we consider polyethylene of different molecular lengths, from the oligomer to unentangled Rouse like systems. By computing the different properties the concept of the interface, and the interphase as well, in polymer nanocomposites with metal NPs are critically examined. Results concerning polymer density profiles, bond order parameter, segmental and terminal dynamics show clearly that the size of the interface / interphase, depends on the actual property under study. In addition, the anchored polymeric chains change the behavior/properties, and especially the chain density profile and the dynamics, of the polymer chain at the vicinity of the Au NP.

Concrete production requires a significant amount of natural resources, with aggregates comprising between 55% and 80% of the total volume. However, over-exploitation of natural aggregates has led to the exploration of alternative materials for use in concrete production. In this study, crushed hazelnut shells were investigated as a partial replacement for fine aggregate, addressing the problem of natural resource depletion and offering a second use for this important agricultural waste product available in Chile. Hazelnut shells were incorporated in percentages of 2.5%, 5%, and 10% by weight of sand for water-cement ratios of 0.4 and 0.5. The compressive strengths at 7 and 28 days and bending tensile strengths at 28 days were determined, alongside physical properties such as workability, temperature, air content, fresh density, and hardened density of the concrete. Our findings show that replacing 2.5% of the fine aggregate with hazelnut shells led to higher compressive strength at 28 days, exceeding the strength of the standard specimens by 9.5%, whereas replacing 5% of the fine aggregate led to the highest bending tensile strength, exceeding the resistance of the standard specimens by 3.5%. Moreover, the 0.4 w/c ratio consistently led to better results for both compressive and bending tensile resistances, with fewer and lower reductions in mechanical resistances compared to the standard mixture. Our results suggest that concrete mixes with hazelnut shells as a replacement for fine aggregate at a percentage of up to 2.5% can be used in constructive systems with compression strengths lower than 17 MPa, and mixtures with up to 10% hazelnut shell replacement can be used in structures with tensile bending stress requirements lower than 6 MPa. Overall, the use of hazelnut shells as a partial replacement for fine aggregate in concrete production presents an environmentally-friendly and cost-effective solution for the construction industry.

A thin-shell wormhole is crafted by the cut-and-paste method of two Bardeen de-Sitter black holes using Darmois-Israel formalism. Energy conditions are considered for different values of magnetic charge while both mass and cosmological constant are fixed. The attractive and repulsive characteristics of the throat of the thin-shell wormhole are also examined through the radial acceleration. Dynamics and stability of the wormhole are studied around the static solutions of the linearized radial perturbations at the throat of the wormhole. The regions of stability are determined by checking out the condition of concavity of the potential as a function in the throat radius for different values of magnetic charges.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Although promoting healthy eating is a policy objective, the controllability of dietary habits remains uncertain. The personal dietary patterns reflect many factors, of which some are relatively controllable for individual, and others are not. In this article, assuming that some sort of information about controllability of dietary habits is contained in the observed pattern of food consumptions, we focused on dietary pattern on its own. We introduced a statistical descriptive model for data on food frequency questionnaire, estimated strength of pairwise linkage between foodstuffs, and grouped foodstuffs by applying community detection to the networks of the estimated inter-food linkages. Those linkages represent co-movement of pairs of foods consumption. Furthermore, we demonstrated an analysis on the relationship between health of mind and dietary habits considering the aspect of controllability of dietary habits. Using an observational study in Japan, we obtained the following results: 115 foodstuffs were divided into 3 groups for both of genders, but the compositions were different by gender; in the analysis of mental health, some stress response items were associated with the dependence on some of those food groupings. As the grouping of foodstuffs based on our estimation depicted the internal structure of dietary habit that a healthy eating policy should regard as constraint, it follows that we should design the policy along the line with that grouping.

The article focuses on the galvanic replacement synthesis of Ti-Ni and Zr-Ni metal systems with the "core-shell" structure which are potential precursors for intermetallics. The authors defined the effective synthesis parameters and the formation features of polymetallic systems character-ized by granulometric, phase and elemental composition. The X-ray fluorescence and X-ray phase analysis methods showed that the deposition of nickel on dispersed titanium and zirconium leads to the production of test samples with phase composition representing a mechanical mixture of Ni and Ti, Ni and Zr. The method of X-ray fluorescence analysis showed that the presence of hy-drofluoric acid with a 0.5-1.5 M concentration results in the formation of fixed quantitative ratios of elements in the precipitate, which allows the quantitative composition of dispersed systems "titanium - nickel", "zirconium - nickel" to be regulated within a relatively wide range. Scanning electron microscopy proved that all synthesized systems are characterized by a highly porous structure that follows the titanium and zirconium particle surface contour and the presence of spherical nanoscale subunits on the formed particle surface.

In this work, we present a study of ordinary muon capture (OMC) on 136Ba, the daughter nucleus of the 136Xe double beta decay (DBD). OMC rates to low-lying nuclear states (below 1 MeV of excitation energy) in 136Cs are assessed by using both the interacting shell model (ISM) and the proton-neutron quasiparticle random-phase approximation (pnQRPA). We also add the chiral two-body (2BC) meson-exchange currents and use an exact Dirac wave function for the captured s-orbital muon. OMC can be viewed as a complementary probe of the wave functions in 136Cs, the intermediate nucleus of the 136Xe DBD. At the same time OMC can be considered as a powerful probe of the effective values of the weak axial-type couplings in a 100-MeV momentum-exchange region relevant for the neutrinoless DBD. The present work represents the first attempt to compare the ISM and pnQRPA results for the OMC on a heavy nucleus by including also the exact muon wave function and the 2BC. Sensitivity estimates of the present and future neutrinoless DBD experiments will clearly benefit from the future OMC measurements through the OMC calculations similar to the present one.

As the most active plateau on the Earth, the Qinghai-Tibet Plateau has a complex crust-mantle structure. Knowledge of the distribution of such a structure provides information for understanding the underlying geodynamic processes. We obtains a three-dimensional density model of crustal and upper mantle beneath Qinghai-Tibet plateau and its surrounding areas from the residual geoid anomalies using the Earth Gravitational Model (EGM) 2008. We estimate a refined density model by iterations, using an initial density contrast model. We confirm that the EGM2008 mission products can be used to constrain the crust-mantle density structures. Our major findings are: (1). At 300-400 km depth, high-D anomalies terminate around Jinsha River Suture (JRS) in the central TP, suggesting that the Indian plate has been reached over the Bangong Nujiang Suture (BNS) and almost reach to the JRS. (2). On the eastern TP, low-D anomalies at the depth of 0-300 km together with high-D anomalies at 400-670 km further verified the current eastward subduction of Indian plate. The ongoing subduction provides forces to the occurrences of frequent earthquakes and volcano. (3). At 600 km depth, low-D anomalies inside the TP illustrate the existence of hot weak material beneath there, contributing to the external material inward-thrusting.

Capital structure decision plays an imperative role in firm’s performance. Recognizing the importance, there has been many studies inspected the rapport of capital structure with performance of firms and findings of those studies are inconclusive. In addition, there is relative deficiency of empirical studies examining the link of capital structure with performance of banks in Bangladesh. This paper attempted to fill this gap. Using panel data of 22 banks for the period of 2005-2014, this study empirically examined the impacts of capital structure on the performance of Bangladeshi banks assessed by return on equity, return on assets and earnings per share. Results from pooled ordinary least square analysis show that there are inverse impacts of capital structure on bank’s performance. Empirical findings of this study is of greater significance for the developing countries like Bangladesh because it will call upon concentration of the bank management and policy makers to pursue such policies to reduce reliance on debt and to accomplish optimal level capital structure. This research also contributes to empirical literatures by reconfirming (or otherwise) findings of previous studies.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P<0.05), left hippocampus volume (LHV, β: -0.02435, P<0.01) and right hippocampus volume (RHV, β: -0.02544, P<0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P<0.05) and LHV (β: -0.01173, P<0.05) and RHV (β: -0.01193, P<0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P<0.05; RHV, β: -0.005527, P<0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

The temperature-dependent intensities of the exciton (X) and biexciton (XX) peaks from single GaAs cone-shell quantum dots (QDs) are studied with micro photoluminescence (PL) at varied excitation power and QD size. The QDs are fabricated by filling of self-assembled nanoholes, which are drilled in an AlGaAs barrier by local droplet etching (LDE) during molecular beam epitaxy (MBE). This method allows the fabrication of strain-free QDs with sizes precisely controlled by the amount of material deposited for hole filling. Starting from the base temperature T = 3.2 K of the cryostat, single-dot PL measurements demonstrate a strong enhancement of the exciton emission up to a factor of five with increasing T. Both, the maximum exciton intensity and the temperature Tx,max of the maximum intensity depend on excitation power and dot size. At an elevated excitation power, Tx,max becomes larger than 30 K. This allows an operation using an inexpensive and compact Stirling cryocooler. Above Tx,max, the exciton intensity decreases strongly up to its disappearance. The experimental data are quantitatively reproduced by a model which considers the competing processes of exciton generation, annihilation, and recombination. Exciton generation in the QDs is given by the sum of direct excitation in the dot plus additional bulk excitons diffusing from the barrier layers into the dot. The thermally-driven bulk-exciton diffusion from the barriers causes the temperature enhancement of the exciton emission. Above Tx,max, the intensity decreases due to exciton annihilation processes. In comparison to the exciton, the biexciton intensity shows an only very weak enhancement, which is attributed to more efficient annihilation processes.

Core-shell particles are heterogenous micro- or nanoparticles with solid, liquid or gas core encapsulated by a protective solid shell. The unique composition of core and shell materials imparts smart properties to the particles. Core-shell particles are gaining increasing attention as tuneable and versatile carriers for pharmaceutical and biomedical applications including targeted drug delivery, controlled drug release, and biosensing. This review first provides an overview of fabrication methods for core-shell particles, followed by a brief discussion on their application and a detailed analysis on manipulation including assembly, sorting, and triggered release. We compile current methodologies employed for manipulation of core-shell particles and demonstrate how existing methods of assembly and sorting micro/nanospheres can be adopted or modified for core-shell particles. Various triggered release approaches for diagnostics and drug delivery are also discussed in detail.

The need for quick and easy deflection calculations of various prefabricated slabs causes that simplified procedures and numerical tools are used more and more often. Modelling of full 3D finite element (FE) geometry of such plates is not only uneconomical but often requires the use of complex software and advanced numerical knowledge. Therefore, numerical homogenization is an excellent tool, which can be easily employed to simplify a model, especially when accurate modelling is not necessary. Homogenization allows for simplifying a computational model and replacing a complicated composite structure with a homogeneous plate. Here, a numerical homogenization method based on strain energy equivalence is derived. Using the method proposed, the structure of the prefabricated concrete slabs reinforced with steel spatial trusses is homogenized to a single plate element with an effective stiffness. There is a complete equivalence between the full 3D FE model built with solid elements combined with truss structural elements and the simplified homogenized plate FE model. The method allows for the correct homogenization of any complex composite structures made of both solid and structural elements, without the need to perform advanced numerical analyses. The only requirement is a correctly formulated stiffness matrix of a representative volume element (RVE) and appropriate formulation of the transformation between kinematic constrains on RVE boundary and generalized strains.

By introducing a variable transformation $\xi=\frac{1}{2}(\sin \theta+1)$, the symmetrical deformation equation of elastic toroidal shells is successfully transferred into a well-known equation, namely Heun's equation of ordinary differential equation, whose exact solution is obtained in terms of Heun's functions. The computation of the problem can be carried out by symbolic software that is able to with the Heun's function, such as Maple. The Gauss curvature of the elastic toroidal shells shows that the internal portion of the toroidal shells has better bending capacity than the outer portion, which might be useful for the design of metamaterials with toroidal shells cells. Through numerical comparison study, the mechanics of elastic toroidal shells is sensitive to the radius ratio. By slightly adjustment of the ratio might get a desired high performance shell structure.

This study focuses on examining the determinants of capital structure and the influence of taxes within Iran Khodro Company in the automobile industry from 2016 to 2023. The research analyzes the relationship between debt, taxes, and various company-specific factors. Findings indicate a direct relationship between taxes and debt, with financial leverage being the most significant element related to taxes. The study aims to provide valuable insights for managers and decision-makers in enhancing financial decision-making and shareholder wealth. Various studies have also been conducted on the impact of taxes and different factors on the capital structure of companies listed on the Tehran Stock Exchange, highlighting the importance of tax implications in financial decisions.

GABAA receptors are channel proteins crucial to mediating neuronal balance in the CNS. The structure of GABAA receptors allows for multiple binding sites and is key to drug development. Yet, the formation mechanism of the receptor’s distinctive pentameric structure is still unknown. This study aims to investigate the role of three predominant subunits of the human GABAA receptor in the formation of protein pentamers. Through purifying and refolding the protein fragments of the GABAA receptor α1, β2, and γ2 subunits, homopentamers were visualised with negative staining and Cryo-EM. To aid the analysis, AlphaFold2 was used to compare the structures. Results show that α1 and β2 subunit fragments successfully formed homo-oligomers, particularly homopentameric structures, while the predominant heteropentameric GABAA receptor was also replicated through the combination of the three subunits. However, it is still unclear whether γ2 subunits can form homopentamers or their main purpose is to bring together the α1 and β2 subunits to form GABAA receptors. Nevertheless, this study will lead to a deeper understanding of the atomic structure of GABAA receptors, especially in the formation mechanism of complex protein structures, and hopefully pave the way to the development of novel therapeutics for neuropsychiatric diseases.

Scaffolds for tissue engineering are expected to respond to a challenging combination of physical and mechanical requirements, guiding the research towards the development of novel hybrid materials. This study introduces innovative three-dimensional bioresorbable scaffolds, in which a stiff poly(lactic acid) lattice structure is meant to ensure temporary mechanical support, while a bioactive gelatin-chitosan hydrogel is incorporated to provide a better environment for cell adhesion and proliferation. The scaffolds present a core-shell structure, in which the lattice core is realized by additive manufacturing, while the shell is nested throughout the core by grafting and crosslinking a hydrogel forming solution. After subsequent freeze-drying, the hydrogel network forms a highly interconnected porous structure that completely envelops the poly(lactic acid) core. Thanks to this strategy, it is easy to tailor the scaffold properties for a specific target application, by properly designing the lattice geometry and the core/shell ratio, which are found to significantly affect the scaffold mechanical performance and its bioresorption. Compression stiffness and strength provided by poly(lactic acid) lattices are overall within the range of values displayed by human bone tissue and remain stable after prolonged immersion in water at body temperature for several weeks. On the other hand, the hydrogel undergoes gradual and homogeneous degradation over time, but the core-shell integrity and structural stability are nevertheless maintained during at least 7-week hydrolytic degradation tests. In vitro experiments with human mesenchymal stromal cells reveal that the core-shell scaffolds are biocompatible and their physical-mechanical properties and architecture are suitable to support cell growth and osteogenic differentiation, as demonstrated by hydroxyapatite formation. These results suggest that the bioresorbable core-shell scaffolds can be considered, and further studied, in view of clinically relevant endpoints in bone regenerative medicine.

This article discusses the fabrication of pullulan/polyvinyl alcohol (PVA) and PVA blends as carrier polymers for drug delivery. This study utilized coaxial electrospinning to encapsulate doxorubicin (DOX), a common anticancer drug, within nanofibers, which helped mitigate the adverse effects of DOX on normal cells. The study also demonstrated that the coaxial electrospinning technique using PVA/pullulan cores was effective in inhibiting the attachment and proliferation of HeLa cells, a type of cervical cancer cell. The use of pullulan/PVA and PVA blends as carrier polymers in conjunction with coaxial electrospinning could provide a safe and effective drug delivery system for the treatment of cervical and other solid malignancies. The study concluded that nanofibers showed promising results in inhibiting the growth of HeLa cells, indicating their potential as safe and effective drug delivery systems for treating cervical cancer and other solid malignant tumors.

Biomass is a widely distributed and renewable source of carbon. The main objective of this work is to produce an activated carbon from coconut shells with suitable characteristics to separate CO2 from biogas. The textural characterization of the adsorbent has been determined. Pure component adsorption isotherms of CO2 and CH4 at 30, 50 and 70 °C have been measured. Moreover, the performance of the produced activated carbon, as potential adsorbent for CO2 capture from a CO2/CH4 gas mixture has been evaluated under dynamic conditions in a purpose-built fixed-bed setup.

Dengue (DENV) and Zika (ZIKV) virus continue to pose significant challenges globally due to their widespread prevalence and severe health implications. Given the absence of effective vaccines and specific therapeutics, targeting of the highly conserved NS5 RNA-dependent RNA polymerase (RdRp) domain has emerged as a promising strategy. However, limited efforts have been made to develop inhibitors for this crucial target. In this study, we employed an integrated in silico approach utilizing combinatorial chemistry, docking, molecular dynamics simulations, MM/GBSA, and ADMET studies to target the allosteric N-pocket of DENV3-RdRp and ZIKV-RdRp. Using this methodology, we designed lycorine analogs with natural S-enantiomers (LYCS) and R-enantiomers (LYCR) as potential inhibitors of non-structural protein 5 (NS5) in DENV3 and ZIKV. Notably, 12 lycorine analogs displayed a robust binding free energy (<-9.00 kcal/mol), surpassing that of RdRp-Ribavirin (<-7.00 kcal/mol) along with promising ADMET score predictions (<4.00), of which (LYCR728-210, LYCS728-210, LYCR728-212, LYCS505-214) displayed binding properties to both DENV3 and ZIKV targets. This study highlights the potential of non-nucleoside lycorine-based analogs with different enantiomers that may present different or even completely opposite metabolic, toxicological, and pharmacological profiles as promising candidates for inhibiting NS5-RdRp in ZIKV and DENV3, paving the way for further exploration for the development of effective antiviral agents.

In the present research, it has been tried to use the applied research bases in the field of business management with marketing orientation. Since there were wide and diverse spectrum in the field of economic activities in Isfahan province and Isfahan city, the model of economic sectors was used to categorize these activities. In this regard, the specific goals of the research in all five sectors of the model of economic sectors, drawing and prioritizing the components (in-dices) of the 7P marketing mix model in each of these economic sectors by the related individuals and members of subgroups of guilds and non-governmental organizations in Isfahan province, have been formed, specified and determined. Collecting data for processing and answer the question of this research, after designing a questionnaire in accordance with the AHP model standard, by spending a period of 2 months from September 2022 and ended in November 2022 , from the statistical population has been done.

The presented research article shows a functionally graded lattice as an infill structure in designing a 3D printed mechanical element—a bicycle crank arm. The authors want to answer the fundamental question: whether the functionally graded lattice structures can efficiently improve structural performance and how they can be implemented in real complex components. Intuitively, everyone senses that using such elements must bring profit. A good example might be nature, which commonly reaches for such a solution in the skeletons of animals and humans. Two aspects determine their realisations: the lack of adequate construction and analysis methods and the limitations of existing manufacturing methods. Thus, the authors used relatively simple crank arm design and design exploration methods for structural analysis. The design exploration method enabled us to find the optimum solution efficiently. A developed prototype was created utilising additive manufacturing. One of the 3D printing methods - fused filament fabrication technology for metals, allowed the prototype of a crank arm with the optimised infill to be made. As a result, the authors developed a lightweight and manufacturable crank arm showing the new construction and analysis method implementable in similar 3D printed elements.

In this paper, the results of finite element analyses of a single-layer cylindrical latticed shell under severe earthquake is presented. A 3D Finite Element model using fiber beam elements were used to investigate the collapse mechanism of this type of shell. The failure criteria of structural members are simulated based on the theory of damage accumulation. Severe earthquake of peak ground acceleration (PGA) of 500 gal was applied to the shell. The stress and defeomation of the shell were studied in detail. A three-stages collapse mechanism “double-diagonal -members-failure-belt” of this type of structure was discovered. Based on the analysis results, the measures to mitigate collapse of this type of structure is recomanded.

Recent research efforts in bone tissue engineering have been primarily directed towards manufacture-viable synthesis of biomaterials that can significantly enhance the biocompatibilities and osteogenic capabilities on the new biomaterials. This paper presents a straightforward, cost-effective, optimized, and well-controlled hydrothermal synthesis of Nb-doped potassium titanate nanofibers in high-purity. Characterization data revealed that the Nb-doping potassium titanate maintained the crystal structure, showing great promise for applications in bone tissue engineering.

By using the method of high-temperature solid-phase reaction, the new piezoceramic SrBi2Nb2-2xWxSnxO9 was obtained, in which partial substitution of niobium (Nb) atoms with Sn4+ and W6+ atoms in the compound SrBi2Nb2O9 took place in the octahedra of the perovskite layer (B-position). X-ray diffraction studies have shown that these compounds are single-phase SrBi2Nb2-2xWxSnxO9 (x = 0.1, 0.2) and two-phase SrBi2Nb2-2xWxSnxO9 (x = 0.3, 0.4), but they all had the structure of Aurivillius – Smolensky phases (ASPs) with similar parameters of orthorhombic elementary cells, corresponding to the spatial group A21am. The dependences on temperature of the relative permittivity ε/ε0 and the tangent of the loss angle tan d at different frequencies were measured.

Sharing confidential information is a critical concern in today’s world. Secret sharing schemes facilitate the sharing of secrets in a way that ensures only authorized participants (shareholders) can access the secret using their allocated shares. Hierarchical secret sharing schemes (HSSSs) build upon Shamir’s scheme by organizing participants into different levels based on priority. Within HSSS, participants at each level can reconstruct the secret if a specified number, denoted as the threshold value (t), or more of them are present. Each level has a predetermined threshold value. If the number of participants falls below the threshold at any level, higher-level participants must be involved in reconstructing the secret at lower levels. Our paper proposes schemes that implement hierarchical access structures and enable the sharing of multiple secrets. Additionally, our proposed scheme includes share verification. We have analyzed potential attacks and demonstrated the scheme’s resistance against them. Through security analysis and comparison with existing schemes, we highlight the novelty and superiority of our proposed approach, contributing to advancements in secure information sharing practices.

Calcium dihydrogen phosphate monohydrate [Ca(H2PO4)2·H2O] (a fertilizer) was successfully synthesized by the recrystallization process by using a prepared triple superphosphate (TSP) that derived from oyster shell waste as starting material. This bio-green, eco-friendly process to produce an important fertilizer can promote a sustainable society. The shell-waste-derived TSP was dissolved in distilled water and kept at 30, 50, and 80 °C. Non-soluble powder and TSP solution were obtained. The TSP solution fraction were then dried and the recrystallized products (RCP30, RCP50, and RCP80) were obtained and confirmed as Ca(H2PO4)2·H2O. Whereas the non-soluble products (NSP30, NSP50, and NSP80) were observed as calcium hydrogen phosphate dihydrate (CaHPO4·2H2O). The recrystallized yields of RCP30, RCP50, and RCP80 were found to be 51.0%, 49.6%, and 46.3%, whereas the soluble percentages were 98.72%, 99.16%, and 96.63%, respectively. RCP30 shows different morphological plate sizes, while RCP50 and RCP80 present the coagulate crystal plates. X-ray diffractograms confirm the formation of both the NSP and RCP. The infrared adsorption spectra confirmed the vibrational characteristics of HPO42‒, H2PO4‒ and H2O existed in CaHPO4·2H2O and Ca(H2PO4)2·H2O. Three thermal dehydration steps of Ca(H2PO4)2·H2O (physisorbed water, polycondensation, and re-polycondensation) were observed. Ca(H2PO4)2 and CaH2P2O7 are the thermodecomposed products from the first and second steps, whereas the final product is CaP2O6.

A triangular lattice model for pattern formation by core-shell particles at fluid interfaces is introduced and studied for the particle to core diameter ratio equal to 3. Repulsion for overlapping shells and attraction at larger distances due to capillary forces are assumed. Ground states and thermodynamic properties are determined analytically and by Monte Carlo simulations for soft outer- and stiffer inner shells, with different decay rates of the interparticle repulsion. We find that thermodynamic properties are qualitatively the same for slow and for fast decay of the repulsive potential, but the ordered phases are stable for temperature range depending strongly on the shape of the repulsive potential. More importantly, there are two types of patterns formed for fixed chemical potential - one for a slow and another one for a fast decay of the repulsion at small distances. In the first case two different patterns - for example clusters or stripes - occur with the same probability for some range of the chemical potential. For fixed concentration, an interface is formed between two ordered phases with the closest concentration, and the surface tension takes the same value for all stable interfaces. In the case of degeneracy, a stable interface cannot be formed for one out of four combinations of the coexisting phases, because of a larger surface tension. Our results show that by tuning the architecture of a thick polymeric shell, many different patterns can be obtained for sufficiently low temperature.

Acidic ostreolysin A/pleurotolysin B (OlyA/PlyB, formerly known as ostreolysin (Oly), and basic 20 kDa equinatoxins (EqTs) are cytolytic proteins isolated from the edible mushroom Pleurotus ostreatus and the sea anemone Actinia equina, respectively. Both toxins, although from different sources, share many similar biological activities: (i) colloid-osmotic shock by forming pores in cellular and artificial membranes enriched in cholesterol and sphingomyelin; (ii) increased vascular endothelial wall permeability in vivo and perivascular oedema; (iii) dose-dependent contraction of coronary vessels; (iv) haemolysis with pronounced hyperkalaemia in vivo; (v) bradycardia, myocardial ischemia and ventricular extrasystoles accompanied by progressive fall of arterial blood pressure and respiratory arrest in rodents. Both types of toxins are haemolytic within nanomolar range concentrations, and it seems that hyperkalaemia plays an important role in toxin cardiotoxicity. However, it was observed that the haemolytically more active EqT III is less toxic than EqT I, the most toxic and least haemolytic EqT. In mice, EqT II is more than 30 times more toxic than OlyA/PlyB when applied intravenously. These observations imply that haemolysis with hyperkalaemia is not the sole cause of the lethal activity of both toxins. Additional mechanisms responsible for lethal action of the two toxins are direct effects on heart, coronary vasoconstriction and related myocardial hypoxia. In this review, we appraise the pathophysiological mechanisms related to the chemical structure of OlyA/PlyB and EqTs, as well as their toxicity.

The paper discusses the mechanism of montmorillonite structure alteration and bentonites properties modification (on the example of samples from clay deposit Taganka, Kazakhstan) due to the thermochemical treatment (treatment with inorganic acid solutions at different temperatures, concentrations and reaction times). With the use of the suit of methods certain processes were distinguished: transformation of montmorillonite structure, which appears in the leaching of interlayer and octahedral cations, protonation of the interlayer and OH groups at octahedral sheets. Changes in the structure of the 2:1 layer of montmorillonite and its interlayer result in significant changes in the properties – reduction of cation exchange capacity and an increase of specific surface area. The results of the work showed that bentonite clays retain a significant portion of its adsorption properties even after the long term and intense thermochemical treatment (6M HNO3, 60°C, 108 hours)

The dynamic response of the shed-tunnel structure under rockfall impact attracts much attention in recent years. However, the research on the dynamic response of the shed-tunnel structure under rockfall impact mostly focuses on the rockfall single impact, while in practical engineering, the shed-tunnel structure often encounters the rockfall repeated impacts during its service life. Therefore, this research focuses on exploring the dynamic response characteristics of the shed-tunnel structure under the rockfall repeated impacts. First of all, based on the model test of the shed-tunnel under rockfall impact as a reference, the FEM (Finite Element Method)-SPH (Smoothed Particle Hydrodynamics) coupling numerical calculation model is established based on ANSYS/LS-DYNA finite element code. The numerical simulation of the dynamic response of the shed-tunnel structure under rockfall impact is realized, and the rationality of the model is verified. Then, with this model and the full restart technology of LS-DYNA code, the effects of four factors, e.g. rockfall mass, rockfall impact velocity, rockfall impact angle and rockfall shape, on the impact force and impact depth of the buffer layer, the maximum plastic strain and axial force of the rebar, the shed roof vertical displacement and the shed-tunnel plastic strain are studied. These results show that the cumulative deformation and damage of the shed-tunnel structure caused by the rockfall repeated impacts play an important role in the destruction of the shed-tunnel structure, and the special attention should be paid to this issue.

The Ylistrum japonicum is a commercially valuable scallop known for its long-distance swimming abilities. Despite its economic importance, genetic and genomic research on this species is limited. This study presents the first complete mitochondrial genome of Y. japonicum. The mitochondrial genome is 19,475 bp long and encompasses 13 protein-coding genes, 3 ribosomal RNA genes, and 23 transfer RNA genes. By selecting 15 Pectinidae species and additional outgroup taxa, we have constructed phylogenetic trees to elucidate the evolutionary placement of Ylistrum within the family Pectinidae. Our analysis reveals that Ylistrum is a basal lineage to the Pectininae clade, distinct from its previously assigned tribe, Amusiini. This study offers critical insights into the genetic makeup and evolutionary history of Y. japonicum, enhancing our knowledge of this economically vital species.

Bio-inspired gyroid triply periodic minimum surface (TPMS) lattice structures have been the focus of research in automotive engineering because they can absorb a lot of energy and have wider plateau ranges. The main challenge is determining the optimal energy absorption capacity and accurately capturing plastic plateau areas using finite element analysis (FEA). Using nTop's Boolean subtraction method, this study combined walled TPMS gyroid structures with normal TPMS gyroid lattice. This made a composite TPMS-gyroid lattice with relative densities ranging from 14% to 54%. Using the ideaMaker software and the fused deposition modeling (FDM) Raise3D Pro 2 3D printer to print polylactic acid (PLA) bioplastics in 1.75 mm filament made it possible to slice computer aided design (CAD) models and fabricate 36 lattices samples precisely layer by layer technique. Shimadzu 100kN testing equipment was utilized for the mechanical compression experiments. And the validation using finite element analysis (FEA). Further, CTG was examined using a field emission scanning electron microscope (FE-SEM) before and after compression testing. The composite TPMS gyroid lattice showed potential as shock absorbers for vehicles with relative densities of 33%, 38%, and 54%. The Gibson-Ashby model showed that the composite TPMS gyroid lattice deformed mainly by bending, and the size effect was seen when the relative densities were less than 15%. The lattice's relative density had a significant impact on its ability to absorb energy. The research also explored the use of these innovative foam-like composite TPMS-gyroid lattices in high-speed crash box scenarios, potentially enhancing vehicle safety and performance.

Depressions containing partially molten rocks were investigated in Quaternary pebbly sedi-ments in Alpine foreland in Bavaria, Germany. Ruins of limekilns from 18-19th centuries are abundant around Seeshaupt. They are usually associated with earthworks for fuel feeding and protection from wind. Depressions contain partially molten stones from furnace walls, with lime and burnt loam remnants. On the surface of pebbles (typically gneisses), green glass formed with chemical composition possibly affected by moderately volatile components of wood biomass, mainly K and Cu. Thermoplastic deformation of pebbles is limited and the sur-face melt deformation points to slow flow. At Emmerting, on the other hand, two walled circu-lar depressions which lack additional earthworks have been identified as possible impact cra-ters. Thermally affected pebbles show much more intense deformation. Colorless to greenish glass, also K and Cu enriched, usually forms only thin surface coatings, in places covered by younger melt extruded from pebble interior. Burnt loam is missing. At Grabenstätt-Kaltenbach, a depression of unclear origin was investigated. Morphologically, it matches craters rather than limekilns, but anthropogenic contamination (brick-like material) is probable. The rare molten samples do not display extreme deformation features. The thermally affected stones, mainly those from Emmerting, have elevated magnetic susceptibility.

This paper investigates the impact of debt financing on dividend payments when they face the agency costs of free cash flow. Focusing on a sample of 120 firms listed on the Saudi Stock Exchange during the period 2011-2021. The study found a negative association between agency cost of free cash flow and dividend payment. More importantly, our research highlights the significant role of long-term debt in making more prudent use of free cash flow. The obligation to meet interest and principal payments acts as an incentive for them to steer clear of unprofitable expenses and risky investments. Concurrently, long-term debt imposes restrictive clauses in debt contracts, such as minimum dividend distribution requirements, which further encourage higher dividend payments. Since interest and debt repayments are fixed obligations, using free cash flow for dividend disbursement is considered a more profitable and beneficial approach for shareholders in the context of Saudi Arabia.