Accurately predicting the distance an object will travel to its destination is very important in various sports. Acceleration sensors as a means of real-time monitoring are increasingly gaining increasing attention in sports. Due to the low energy output and power density of Triboelectric Nanogenerators (TENGs), recent efforts have focused on developing various acceleration sensors. However, these sensors suffer from significant drawbacks of large size, complexity, high power input requirements, and high cost. Here, we described a portable and cost-effective real-time refreshable strategy design comprising a series of individually addressable and controllable units based on TENGs embedded in a flexible substrate. This results in a highly sensitive, low-cost, and self-powered acceleration sensor. Putting, which accounts for nearly half of the strokes played, is obviously an important component of the golf game. The developed acceleration sensor has an accuracy controlled within 5 %. The initial velocity and acceleration of the forward movement of a rolling golf ball after it is hit by a putter can be displayed, and the stopping distance quickly calculated and predicted in about 7 seconds. This research demonstrates the application of the portable TENG-based acceleration sensor, while paving the way for designing portable, cost-effective, scalable, and harmless ubiquitous self-powered acceleration sensors.

The use of sensors in monitoring of lateral accelerations in delivery van transport focuses on measuring lateral accelerations on routes with roundabouts and curves to increase road safety. Using microelectromechanical system (MEMS) sensors, it measures the lateral accelerations acting on the vehicle and the load being transported during the test drives to study vehicle dynamics for cargo securing. Using an accelerometer and position tracking, accelerations can be detected when traversing curves and roundabouts at selected locations on the vehicle. The level of accelerations on the roof of the vehicle was found to be like those occurring on a lashed load with limited movements, where regression analysis can be used to determine the relationship between lateral accelerations at different sensor positions. If we compare the mean values of the lateral accelerations of the individual events between the sensors, the sensor on the side of the vehicle body at the height of the sensor on the load had approximately 5% lower mean values than the sensor on the roof. The sensor on the load measured approximately 5% higher mean values than the sensor on the roof. Hence, the mean lateral accelerations of the individual events for the sensor on the load are 10% higher than for the sensor at the same height on the vehicle body. From the above testing, we can say that the values of the mean lateral accelerations of the van from the sensor on the roof of the vehicle, are closer to the values of the accelerations of the sensor on the load than to the values of the sensor on the body of the vehicle at the same height.

In relativity, the Newtonian concepts of velocity and acceleration are observer-dependent quantities that vary with the chosen frame of reference. It is well established that in the comoving frame, cosmic expansion is currently accelerating; however, in the rest frame, this expansion is actually decelerating. In this paper, we explore the implications of this distinction. The traditional measure of cosmic acceleration, denoted by q, is derived from the comoving frame and describes the acceleration of the scale factor a for a 3D space-like homogeneous sphere. We introduce a new parameter q_E representing the acceleration experienced between observers within the light cone. By comparing q_E to the traditional q using observational data from Type Ia supernovae (SN) and the radial clustering of galaxies and quasars (BAO)—including the latest results from DESI2024—our analysis demonstrates that q_E aligns more closely with these data. The core argument of the paper is that Λ—regardless of its origin—creates an event horizon that divides the manifold into two causally disconnected regions analogous to conditions inside a black hole’s interior, thereby allowing for a rest-frame perspective q_E in which cosmic expansion appears to be decelerating and the horizon acts like a friction term. Such a horizon suggests that the universe cannot maintain homogeneity outside. The observed cosmological constant Λ can then be interpreted not as a driver of new dark energy or a modification of gravity but as a boundary term exerting an attractive force, akin to a rubber band, resisting further expansion and preventing event horizon crossings. This interpretation calls for a reconsideration of current cosmological models and the assumptions underlying them.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

In this study we used a non-autonomous Chua’s Circuit, and the fractional Lorenz chaos system together with a detection method from Extension theory to analyze the voltage signals. The measured bearing signals by acceleration sensor were introduced into the master and slave systems through a Chua’s Circuit. In a chaotic system minor differences can cause significant changes that generate dynamic errors, and extension matter-element models can be used to judge the bearing conditions. Extension theory can be used to establish classical and sectional domains using the dynamic errors of the fault conditions. The results obtained were compared with those from Discrete Fourier Transform analysis, Wavelet analysis and an integer order chaos system. The diagnostic ratio showed the fractional order master and slave chaos system calculations. The results show that the method presented in this paper is very suitable for monitoring the operational state of ball bearing system to be superior to the other methods. The diagnosis ratio was better and there were other significant advantages such as low cost and few.

We propose novel spectrometer designs that aim to enhance the measured spectral range 1 of ions on a finite-sized detector. In contrast to the traditional devices that use uniform magnetic 2 field, in which the deflection of particles increases inversely proportional to their momentum, in a 3 gradient magnetic field, the deflection of particles will be decreased due to the reduction of the 4 magnetic field along their propagation. Low energy ions are particularly impacted, as they are 5 deflected less and are more likely to reach the detector compared to being driven out of it while 6 using a uniform magnetic field. By the means of a gradient magnetic field, the nonlinear dispersion 7 of ions in a homogeneous magnetic field can approach a nearly linear dispersion. Nonetheless, 8 the dispersion of low energy ions in a homogeneous magnetic field remains unnecessarily high. 9 In this article, we explore linear, quadratic, and higher-order field profiles in comparison to the 10 homogeneous field case. We discuss the employed methodology and present simulation results of 11 the spectrometer with an extended ion spectral range, focusing on the minimum detectable energy 12 (energy dynamic range) and energy resolution

Seaports are critical hubs in global trade, facing increasing pressure to accelerate green transi-tions while navigating evolving economic and environmental landscapes. This research analyses the intricate relationship between port organizational ecosystem resilience and the successful implementation of green transitions, highlighting the challenges and opportunities in moving towards a more sustainable future. The research employed a combined focus group interview and participatory observation methodology to gather insights from experts. Analysis revealed that while technological advancements are a primary driver for greening port operations, a lack of managerial capacity is a significant impediment to the successful integration of these innova-tions. It was identified several challenges, including outdated infrastructure, cybersecurity threats, and the need for ongoing investments in new technologies, along with the need to foster a sustainable behaviour culture. Experts emphasized the importance of developing managerial competencies and continuous learning. The research also highlights the role of strong stake-holder partnerships, including collaboration with government agencies, industry associations, and environmental organizations. This research provides valuable insights for policymakers, port managers, and other stakeholders seeking to navigate the challenges for ensuring a sus-tainable future for the maritime sport organizational ecosystems and maritime industry.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

The importance of bio robotics has been increasing day by day. Researchers are trying to mimic nature in a more creative way so that, the system can easily adopt the complex nature and its environment. Hence, bio robotic gripper plays a role in physical connection between the environment and bio robotics system. While handling the physical world in biorobots gripper, the complexity occurs in feedback system where sensor plays a vital role. Therefore, human centered gripper sensor has a good impact on bio robotics field. But categorical classification and their selection process is not very systematic. This review paper follows PRISMA methodology to summarize the previous works on bio robotics gripper sensor and its selection process.. This paper discusses challenges in soft robotics systems, and the importance of sensing systems to facilitate critical control mechanisms along with their selection considerations. Furthermore, a classification of soft actuation based on gripper has been introduced. Moreover, some unique characteristics for soft robotics sensor are explored namely compliance, flexibility, multifunctionality, sensor nature, surface properties, and material requirements. In addition, a categorization of sensors for soft robotic gripper in terms of modalities has been established ranging from the tactile and force sensor to slippage sensor. Various tactile sensors ranging from piezoelectric sensing to optical sensing are explored as it has utmost importance in soft gripper to effectively address the increasing requirements for intelligence and automation. Finally, taking everything into consideration, a flow diagram has been suggested for selecting sensors specific to soft robotics applications.

In this paper, the mechanism of combined process of ion beam sputtering (IBS) and HF acid etching on the chemical structure defects of fused silica and its laser damage resistance perfor-mance were investigated. During the removal process of surface material, the sputtering effect causes lattice atoms to detach from their original positions, forming a large number of unsaturated structures on silica surface, which improves the chemical activity of Si and O atoms, accelerates the chemical reaction process between surface atoms and water molecules, increases the content of hydroxyl (OH-) groups in the shallow layer, and enhances the photothermal weak absorption intensity. However, the presence of OH- groups reduces the bonding strength of Si-O, destroys the spatial network structure of silica bulk, and reduces the mechanical strength of silica surface, resulting in a decrease in its laser damage resistance performance. The paper reveals for the first time the mechanism of IBS to change the structure characteristics of silica material, accelerate the surface hydroxylation process, and thereby reduces the laser damage resistance performance. This work provides technical guidance for effectively suppressing chemical structure defects on silica surface and improving laser damage resistance performance of optical components under high-flux laser irradiation.

In this paper, we explore the use of superluminal ionization fronts to accelerate and amplify electromagnetic radiation. These fronts are defined as optical boundaries between two regions of a gas, the neutral region and the plasma region, characterized by two different values of the refractive index. For that reason, the front velocity is not necessarily related with the motion of material particles, such as neutral atoms, ions and electrons, which can stay at rest. The fronts can therefore become superluminal without violating causality. In recent years, different experimental configurations, such as the flying-focus, showed that it is possible to create superluminal fronts in the laboratory. These fronts can easily be described theoretically in a special reference frame, called the time-frame, which is used here. In this frame, superluminal fronts reduce to time-refraction, a process that is symmetrical to the well-known optical refraction. We show that propagation through such fronts can lead to considerable frequency shift and energy amplification of probe laser beams. This could eventually be used to develop new sources of turnable radiation.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

In this paper, inspired by quantum field theory, or more specifically QED, we propose a dynamical model for relativity. By adopting the approach provided by this dynamical model, we provide a dynamical explanation for relativistic phenomena such as length contraction, time dilation and clock desynchronization. The result of the dynamical approach for clock desynchronization is especially interesting. Our dynamical approach exhausts the freedom for different clock synchronizations on frames accelerated from an initial reference frame, which is allowed by Einstein’s principle approach. Furthermore, our dynamical approach arrives at the interesting conclusion that Einstein’s equivalence principle and gravitational redshift are necessary to explain special relativistic clock desynchronization. This result shows that special relativity by itself is an incomplete theory. If our dynamical model assumptions are assumed to be valid at a fundamental level, it implies some modifications to quantum field theory and general relativity via the equivalence principle. These modifications have been discussed.

In electromagnetic ultrasonic testing, it is difficult to recognize small-size bottom cracks by time of flight (ToF), and the lift-off fluctuation of the probe affects the accuracy and consistency of the inspection results. In order to overcome the difficulty, a novel EMAT (electromagnetic acoustic transducer)-PEC (pulse eddy current) composite sensor is designed. We use amplitude of bottom echo recorded by EMAT to identify the tiny bottom crack as well as the amplitude of PEC signals picked up by the integrated symmetric coils to measure the average lift-off of the probe in real time. Firstly, the effects of lift-off and bottom cracks on amplitude of bottom echo are distinguished combining the theoretical analysis and finite element method (FEM). And then an amplitude correction method based on the fusion of EMAT and PEC signals is proposed to reduce the impact of lift-off on the defect signal. The experimental results demonstrate that the designed composite sensor can effectively detect the bottom crack as small as 0.1mm* 0.3mm. The signal fusion method can accurately correct the amplitude of defect signal and the relative error is less than ±8%.

The article presents an innovative method for synthesizing radiation patterns efficiently by 1 combining the Taguchi method and neural networks, while validating the results on a 10-element 2 antenna array. The Taguchi method aims to minimize product and process variability, while neural 3 networks are used to model the relationship between antenna design parameters and radiation 4 pattern characteristics. This approach utilizes Taguchi parameters as inputs for the neural network, 5 which is then trained on a dataset generated by the Taguchi method. After training, the network is 6 validated using a real 10-element antenna array. Analytical results demonstrate that this method 7 enables efficient synthesis of radiation patterns with a significant reduction in computation time 8 compared to traditional approaches. Furthermore, validation on the antenna array confirms the 9 accuracy and robustness of the approach, showing a high correlation between predicted performances 10 by the neural network model and actual measurements on the antenna array.In summary, our article 11 highlights that the combined use of the Taguchi method and neural networks, with validation on a 12 real antenna array, offers a promising approach for efficient synthesis of antenna radiation patterns. 13 This approach combines speed, accuracy, and reliability in antenna system design.

The state of the grinding wheel in the grinding process directly affects the surface quality of the workpiece. The monitoring of the wear state of the grinding wheel can effectively identify the wear information of the grinding wheel and timely and effectively repair the grinding wheel. In this paper, a multi-sensor fusion precision grinding wheel wear intelligent monitoring system is established for typical difficult-to-machine aerospace material titanium alloy, and a multi-eigenvalue fusion algorithm based on improved support vector machine (SVM) is proposed. The extracted sound emission signal wavelet packet decomposition coefficient mean square value, force signal grinding force ratio, and vibration signal effective value are used as the input of the improved support vector machine, and the identification strategy is adjusted by the entropy weight evaluation method. The results show that the monitoring system established in this paper can effectively identify the wear state of the grinding wheel, and the monitoring accuracy can reach more than 92%.

Plastic contamination of small dimensions (

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

Acceleration rates of vehicles are crucially important statistics needed in two main aspects: first, they are essential to incident reconstructor professionals as having a verified database on where basing the cinematic reconstructions is definitely difficult and moreover, they are useful in order to understand how to create the safest possible environment on the road. This key topic gives es-sential information for road design like intersection schemes, acceleration and deceleration lane length as well as traffic simulation modelling and furthermore, to educate vehicle drivers when entering the traffic flow and to provide limit acceleration values needed to develop autonomous vehicle’s software in order to guarantee a comfort drive. Literature reports tons of linear acceleration stats mainly referred to vehicle performances claimed by car manufacturers, but these data don’t recreate real drivers’ behaviour when entering the road by turning left or right or crossing an intersection. This work aims to integrate the most reliable data from literature with a hybrid and an electric vehicles statistic, adding also two contemporary thermal engine vehicles, extracted conducting probes that recreates real road environment. The entirety of these experiments reconstructs the scenario in which a car is entering the traffic of a two-lanes road, from a stationary position at a stop sign and the acceleration rates are collected using a M.E.M.S. (Microelectromechanical system). Finally, the space needed between the car that is about to enter or crossing the road and the car that is approaching the intersection is calculated, basing the computations on the acceleration values extracted from the probes. These spaces are pictured, as a way to give a concrete idea to readers.

In this article it is shown how Milgrom’s acceleration constant is related with the Ω_Λ, Ω_m and Ω_B values of the matter distribution within observable universe as defined in the Standard Model of Cosmology, established by the Planck Collaboration Group. The result is a two-parameter model for the observable universe. The two parameters are the age of the universe and Milgrom’s acceleration constant. It is shown that these are sufficient to calculate the amounts of matter and dark energy in the universe, as well as the contributions of dark matter and baryonic matter in the matter part. The numerical results are in agreement with those of the Lamda-CDM model.

Structural displacement is an important metric for assessing structural conditions because it has a direct relationship with the structural stiffness. Many bridge displacement measurement techniques have been developed, but most methods require fixed reference points in the vicinity of the target structure which limits field implementations. A promising alternative is to use reference-free measurement techniques that indirectly estimate the displacement by using measurements such as acceleration, and strain. This paper proposes novel reference-free bridge displacement estimation by the fusion of single acceleration with pseudo-static displacement derived from co-located strain measurements. First, we propose a conversion of the strain at the center of a beam into displacement based on the geometric relationship between strain and deflection curves with reference-free calibration. Second, an adaptive Kalman filter is proposed to fuse the displacement generated by strain with acceleration by recursively estimate the noise covariance of displacement from strain measurements which is vulnerable to measurement condition. Both numerical and experimental validations are presented to demonstrate the efficiency and robustness of the proposed approach.

Traditional population-based metaheuristic algorithms are effective in solving complex real-world problems but require careful strategy selection and parameter tuning. Parameter-less population-based optimization algorithms have gained importance due to their simplicity and efficiency. However, research on their applicability for solving large systems of nonlinear equations is still incipient. In this paper, a systematic review and detailed description of metaphor-less optimization algorithms is made, including the Jaya algorithm, the main Jaya variants for continuous optimization problems, with a focus on the Enhanced Jaya (EJAYA) algorithm, the three Rao algorithms, the best-worst-play (BWP) algorithm, and the very recent max-min-greedy-interaction (MaGI) algorithm. This paper also discusses a few previous parallelizations of the Jaya optimization algorithm, as well as recent GPU-based massively parallel implementations of the Jaya, Enhanced Jaya (EJAYA), Rao, and BWP algorithms developed by the authors. In addition, a novel GPU-accelerated version of the MaGI algorithm is proposed. The GPU-accelerated versions of the metaphor-less algorithms developed by the authors were implemented using the Julia programming language and tested primarily on GeForce RTX 3090 and NVIDIA A100 GPUs, as well as on Tesla V100S and Tesla T4 GPUs, using a set of difficult, large-scale nonlinear equation system problems. The computational experiments carried out produced quite significant speedups, which highlights the efficiency of the GPU-based versions of the metaphor-less algorithms developed for solving large-scale systems of nonlinear equations.

In this paper, a seamless connection between sensor technology and machine learning (ML) has been presented which has wide applicability in rehabilitation and physical medicine. The intent is to identify an ML algorithm which has a better performance, easy to deploy, and has less training time and consumes less computational resources. In short, we propose an algorithm which maximizes the synergy between a sensor and ML by maximizing classification performance and easy to do implementation, which is robust in computational power and lower in resource consumption. The premise of the work is to show the important considerations for evaluating ML algorithms for Upper-limb activity recognition for Physical medicine and rehabilitation field.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

The emerging wireless energy transfer technology enables sensor nodes to maintain perpetual operation. However, maximizing the network performance while preserving short charging delay is a great challenge. In this work, a Wireless Mobile Charger (WMC) and a Directional Charger (DC) are deployed to transmit wireless energy to the sensor node to improve the network's throughput. To the best of our knowledge, this is the first work to optimize the data sensing rate and charging delay by joint scheduling of MC and DC. We prove we can transmit maximum energy to each sensor node to obtain our optimization objective. In our proposed work, a DC selects a total horizon of equipped with DCs, which selects the horizon of each specific area with based on its antenna orientation. DC's orientation is scheduled for each time slot. Furthermore, multiple MCs are used to transmit energy for sensor nodes which cannot be covered by DCs. We divided the Rechargeable Wireless Sensor Network into several zones via the Voronoi diagram. We deployed a static DC and one MC charging location in each zone to provide wireless charging service jointly. We obtain the optimal charging location of MCs in each zone by solving Mix Integral Programming for energy transmission. The optimization objective of our proposed research is to sense maximum data from each sensor node with the help of maximum energy. The lifetime of each sensor network can increase, and the end delay can be maximized with joint energy transmission. Extensive simulation results demonstrate that our RWSNs are designed significantly to improve network lifetime over the baseline method.

Mobile health technologies enable continuous, quantitative assessment of mobility and gait in real-world environments, facilitating early diagnosis of gait disorders, disease progression monitoring, and prediction of adverse events like falls. Traditionally, mobile gait assessment predominantly relied on body-fixed sensors positioned at the feet or lower trunk. Here, we investigate the potential of an algorithm utilizing an ear-worn motion sensor for spatiotemporal segmentation of gait patterns. We collected 3D acceleration profiles from the ear-worn sensor during varied walking speeds in 53 healthy adults. Temporal convolutional networks were trained to detect stepping sequences and predict spatial relations between steps. The resulting algorithm, mEar, accurately detects initial and final ground contacts (F1 score of 99% and 91%, respectively). It enables determination of temporal and spatial gait cycle characteristics (among others stride time and stride length) with good to excellent validity at a precision sufficient to monitor clinically relevant changes in walking speed, stride-to-stride variability, and side asymmetry. This study highlights the ear as a viable site for monitoring gait and proposes its potential integration with in-ear vital sign monitoring. Such integration offers a practical approach to comprehensive health monitoring and telemedical applications, by integrating multiple sensors in a single anatomical location.

In recent years, large language models have demonstrated remarkable performance across various natural language processing (NLP) tasks. However, deploying these models for real-world applications often requires efficient inference solutions to handle the computational demands. In this paper, we explore the utilization of CPUs for accelerating the inference of large language models. Specifically, we introduce a parallelized approach to enhance throughput by 1) Exploiting the parallel processing capabilities of modern CPU architectures, 2) Batching the inference request. Our evaluation shows the accelerated inference engine gives an 18-22x improvement in the generated token per sec. The improvement is more with longer sequence and larger models. In addition to this, we can also run multiple workers in the same machine with NUMA node isolation to further improvement in tokens/s. Table 2, we have received 4x additional improvement with 4 workers. This would also make Gen-AI based products and companies’ environment friendly, our estimates shows that CPU usage for Inference could reduce the power consumption of LLMs by 48.9% (1252 W for A100 with AMD EPYC 7V13 vs 613 W for Intel® Xeon® Gold 6538N) while providing production ready throughput & latency.

We measure the accelerated cosmic expansion rate of the late-time Universe and derive constraints on cosmological parameters from the final baryon acoustic oscillation (BAO) uncorrelated measurements of different surveys after two decades of dedicated spectroscopic observation combined with the Pantheon sample of Type Ia supernovae, the Hubble diagram of gamma-ray bursts & quasars data, the Cosmic Chronometers data, and the recent Hubble constant value measurement from the Hubble Space Telescope and the SH0ES Team as an additional prior. In Λ cold dark matter (ΛCDM) scenario, the model fit yields Ωm=0.313±0.034 and ΩΛ=0.672±0.025. Combining BAO with CC+Pantheon+QSR+GRB data sets we get H0=69.21±1.22 km s−1 Mpc−1, rd=133.46±2.49 Mpc. For the a flat wCDM model, we get w=−1.111±0.030. For a dynamical evolution of dark energy in a flat w0waCDM cosmology, we get wa=−0.292±0.167. We apply the Akaike information criteria probe to compare the three models, and see that all models are favored and cannot be discarded from the current data.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Currently, there is a high interest in smart sensors and integrated composite materials in various industries such as construction, aviation, automobile, medical, information technology, communication, and manufacturing. Here, a new conceptual design for a force and temperature sensor system is developed by integrating fiber optic Bragg grating sensors embedded within composite materials, and a mathematical model is proposed that allows one to estimate strain and temperature based on signals obtained from optical Bragg gratings. This is important for understanding the behaviors of sensors under different conditions and for creating effective monitoring systems. Describing the strain gradient distribution, especially considering different materials with different values of Young's modulus, provides insight into how different materials respond to applied forces and temperature changes. The shape of the strain gradient distribution was obtained, which is a quadratic function with a maximum value of 1500 µ, with a maximum value at the center of the lattice and a symmetrically decreasing strain value with distance from the central part of the fiber Bragg grating. With axial strain at the installation site of the Bragg grating sensor under applied force values ranging from 10 to 11 N, the change in strain was linear. As a result of theoretical research, it was found that the developed system with fiber-optic sensors based on Bragg gratings embedded in composite materials is resistant to external influences and temperature changes.

The market for autonomous vehicles (AV) is expected to experience significant growth over the coming decades and to revolutionize the future of transportation and mobility. The AV is a vehicle that is capable of perceiving its environment and perform driving tasks safely and efficiently with little or no human intervention and is anticipated to eventually replace conventional vehicles. Self-driving vehicles employ various sensors to sense and perceive their surroundings and, also rely on advances in 5G communication technology to achieve this objective. Sensors are fundamental to the perception of surroundings and the development of sensor technologies associated with AVs has advanced at a significant pace in recent years. Despite remarkable advancements, sensors can still fail to operate as required, due to for example, hardware defects, noise and environment conditions. Hence, it is not desirable to rely on a single sensor for any autonomous driving task. The practical approaches shown in recent research is to incorporate multiple, complementary sensors to overcome the shortcomings of individual sensors operating independently. This article reviews the technical performance and capabilities of sensors applicable to autonomous vehicles, mainly focusing on vision cameras, LiDAR and Radar sensors. The review also considers the compatibility of sensors with various software systems enabling the multi-sensor fusion approach for obstacle detection. This review article concludes by highlighting some of the challenges and possible future research directions.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

The development of a rapid, sensitive, specific method for detecting foodborne pathogens is paramount in supplying safe food to enhance public health safety. Despite the significant improvement in pathogen detection methods, key issues are still associated with rapid methods, such as distinguishing living cells from dead, pathogenic potential or health risk of the analyte at the time of consumption, detection limit, and sample-to-result. The mammalian cell-based assays analyze pathogens' interaction with the host cells and are responsive to only live pathogens or active toxins. In this study, a human embryonic kidney (HEK293) cell line expressing Toll-Like Receptor 5 (TLR-5) and chromogenic reporter system (HEK dual hTLR5) was used for the detection of viable Salmonella in a 96-well tissue culture plate. This cell line responds to low concentrations of TLR5 agonist flagellin. Stimulation of TLR5 ligand activates nuclear factor-kB (NF-κB) - linked alkaline phosphatase (AP-1) signaling cascade inducing the production of secreted embryonic alkaline phosphatase (SEAP). With the addition of a ρ-nitrophenyl phosphate as a substrate, a colored end product representing a positive signal is quantified. The assay's specificity was validated with the top 20 Salmonella enterica serovars and 19 non-Salmonella spp. The performance of the assay was also validated with spiked food samples. The total detection time (sample-to-result), including shortened pre-enrichment (4 h) and selective enrichment (4 h) steps with artificially inoculated outbreak-implicated food samples (chicken, peanut kernel, peanut butter, black pepper, mayonnaise, and peach) was 15 h when inoculated at 1–100 CFU/25 g sample. These results show the potential of HEK-DualTM hTLR5 cell-based functional biosensors for rapid screening of Salmonella.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

Abstract: With the growing integration of the Internet of Things (IoT) in smart buildings, it is crucial to ensure the precise implementation and operation of wireless sensor networks (WSNs). This paper aims to study the implementation aspect of Wireless Sensor Networks (WSNs) in a commercial multi-story building, specifically addressing the difficulty of dealing with variable environmental conditions on each floor. This research addresses the disparity between simulated situations and actual deployments, offering valuable insights that have the potential to signifi-cantly improve the efficiency and responsiveness of building management systems. We obtain real-time sensor data to analyze and evaluate the system’s performance. Our investigation is grounded in the growing importance of incorporating WSNs into buildings to create intelligent environments. By leveraging the capabilities of Contiki operating system, this study employs a specialized simulator to generate simulated data, allowing for a comparison between real-world and simulated scenarios. We provide an in-depth analysis to scrutinize the disparities and commonalities between the datasets obtained from real-world deployments and simulated en-vironments. We highlight the necessity of precise simulation to validate real-life sensor data, shedding light on the challenges and opportunities associated with implementing WSNs in in-telligent buildings. Results obtained show the significance of accurate simulation models for re-liable data representation, providing a roadmap for further developments in the integration of WSNs into intelligent building scenarios. The findings highlight the potential for optimizing living and working conditions based on the real-time monitoring of critical environmental pa-rameters. This includes insights into temperature, humidity, and light intensity, offering oppor-tunities for enhanced comfort and efficiency in intelligent environments.

In the realm of physical activity and sports science, motion tracking emerges as an important tool for specialists aiming to analyze movement data, whether for daily life activities or enhancing athletic performance. This study introduces an innovative approach to motion tracking through the development of a fully embedded smart shoe sensor system, which employs an inertial measurement unit (IMU) affixed to the shoe sole, coupled with six pressure sensors, to provide real-time calculation of individual stride lengths along with other vital movement statistics. Traditional motion tracking methods, which typically rely on various body-attached sensors, often necessitate substantial post-processing, delaying the feedback loop. In contrast, our system is designed to overcome these limitations by offering high-accuracy, real-time feedback with a minimal error rate of 1.88% from our experiments. Such prompt data acquisition facilitates immediate interventions by sports performance coaches or healthcare professionals, significantly contributing to injury prevention and performance enhancement. The experimental outcomes of this study underscore the system’s capability to deliver precise stride length measurements instantaneously, marking a significant advancement in motion tracking technology and its application in sports science and healthcare.

In a previous series of papers relating to the Combined Gravitational Action (CGA), we have exclusively studied orbital motion without spin. In the present paper, we apply CGA to any self-rotating material body, i.e., an axially spinning massive object, which itself may be locally seen as a gravito-rotational source because it is capable of generating the gravito-rotational acceleration, which seems to be unknown to previously existing theories of gravity. The consequences of such an acceleration are very interesting, particularly for Compact Stellar Objects. Independently of the equation of state, it is found that the minimum radius of a stable neutron star is three times its gravitational radius, R_min = 3GM_NS/c², and its critical and maximum internal magnetic field strength cannot exceed the value of 3×10¹⁸ G.

As technology advances, people are increasingly adopting IoT (Internet of Things) devices in smart cities. These devices are equipped with sensors that are connected everywhere, from energy infrastructure and transportation to telecommunications, health and human services, waste management, public safety, and more. People want to access sensor data anytime and everywhere to make better decisions and improve their lives. To achieve this, a sensor integration model has been developed where multiple sensors are integrated under one gateway to manage and share sensor data. However, effective sharing of sensor data requires data security, privacy, confidentiality, fairness, effective architectural design, and low communication and computation costs. These issues need to be addressed in the sensor integration model in smart cities. Existing storage models face challenges in managing sensor data effectively. To overcome these issues and hurdles, a data storage framework leveraging blockchain technology has been proposed within the sensor integration model. This framework ensures data security, privacy, confidentiality, and a fair and transparent financial model, all while minimizing communication and computation costs.

Survivability is a critical concern in WSNs, heavily influenced by energy efficiency. Addressing severe energy constraints in WSNs requires solutions that meet application goals while prolonging network life. This paper presents an energy optimization approach (EOAMRCL) for WSNs, integrating the Grey Wolf Optimization (GWO) for enhanced performance. EOAMRCL aims to enhance energy efficiency by selecting the optimal duty-cycle schedule, transmission power, and routing paths. The proposed approach employs a centralized strategy using a hierarchical network architecture. During the cluster formation phase, an objective function, augmented with GWO, determines the ideal cluster heads (CHs). The routing protocol then selects routes with minimal energy consumption for data transmission to CHs, using transmission power as a metric. In the transmission phase, the MAC layer forms a duty-cycle schedule based on cross-layer routing information, enabling nodes to switch between active and sleep modes according to their network allocation vectors (NAV). This process is further optimized by an enhanced CSMA/CA mechanism, which incorporates sleep/activate modes and pairing nodes to alternate between active and sleep states. This integration reduces collisions, improves channel assessment accuracy, and lowers energy consumption, thereby enhancing overall network performance. EOAMRCL was evaluated in a MATLAB environment, demonstrating superior performance compared to EEUC, DWEHC, and CGA-GWO protocols, particularly in terms of network lifetime and energy consumption. This highlights the effectiveness of integrating GWO and the updated CSMA/CA mechanism in achieving optimal energy efficiency and network performance.

This article uses machine learning analysis of wearable sensor data to explore the topic of driver differentiation. The study focuses on using detailed analyzes of data collected from wearable sensors to identify patterns that differentiate skilled drivers from inexperienced ones. On a predetermined driving route, participants experienced a variety of driving conditions, including parking, navigating cities, driving on highways and driving through residential neighborhoods. The gathered data was analyzed using machine learning techniques, yielding a classification accuracy of 94% overall. The results highlight important differences in sensor data between inexperienced and experienced drivers, providing insight into possible uses for improving safety protocols, driver education, and personalized feedback systems. The article fosters improvements in traffic safety and driver education by offering insightful information on the link between driver behavior analysis and machine learning.

We show that the accelerating expansion phase of the universe can emerge from the group field theory formalism, a candidate theory of quantum gravity. The cosmological evolution can be extracted from condensate states using mean field approximation, in a form of modified FLRW equations. By introducing an effective equation of state w, we can reveal the relevant features of the evolution, and show that with proper choice of parameters, w will approach to −1, corresponds to the behaviour of cosmological constant, results in a late time acceleration and leads to de Sitter spacetime asymptotically.

Consider a robot that is navigating in a space modeled by a graph, and that wants to know its current location. It can send a signal to determine how far it is from each landmark among a set of fixed landmarks. We study the problem of computing the minimum required number of landmarks, and where they should be placed so that the robot can always determine its location. Since the problem is an NP-complete problem, the robot's responses to the actions are slow. To accelerate this response, we can use the parallel version of this problem. In this work, we introduce a new parallel implementation for determining the metric dimension of a given graph. We run the proposed algorithm on a symmetric multi-processing (SMP) cluster using C programming language and the Message Passing Interface (MPI) library. Finally, we run our implementation on four categories of graphs (the tracks in which the robot moves): a cycle graph Cn, a path graph Pn, a triangular snake graph and a ladder graph Ln. Preliminary computational results indicate that the metric dimension problem is an NP-complete problem and prove the ability of the proposed algorithm to achieve a speedup of 6 for 8 processors.

Intraoperative load sensors have been developed with the aim of balancing the soft tissue in the knee during Total Knee Replacements (TKRs). Literature has shown success in soft tissue bal-ancing however, concerns regarding the accuracy of these sensors remain. For this reason, pre-vious research has attempted to create robust sensors for intraoperative use. The design of the sensor in this research has aimed to address the concerns outlined in the literature to create a new and novel smart-sensor for soft-tissue balancing. This new intraoperative load sensor included design features to increase accuracy while artificial intelligence allowed for comprehensive sensing across the entirety of the sensor, providing unparalleled insight during the operation. Notably, the sensor was designed to withstand loads of at least 450 N, ensuring robust perfor-mance of the sensor. To optimize the design process while minimizing cost, Finite Element Analysis was employed. This approach ensured the design features fulfilled their function while maintaining structural integrity to withstand loads. Moreover, the novelty of using training data from simulated data will reduce the iterative process of the labor-intensive collection of training data for the artificial intelligence while reducing human error associated with it. Results from the evaluation demonstrated the ability of this design to successfully bridge the current gap in the market by fulfilling all essential design criteria established within the literature. This innovative smart-sensing tool will in turn enhance patient outcomes and alleviate financial burdens to pa-tients and the healthcare systems by reducing the need for early revision surgeries associated with improper joint tension.

Of the 100,000 railroad bridges in the United States, 50% are over 100 years old. Many of these bridges do not meet the minimum vertical clearance standards, making them susceptible to impacts from over-height vehicles. Impacts can cause structural damage and unwanted disruption to railroad bridge services; rapid notification of the railroad authorities is crucial to ensure that the bridges are safe for continued use and to affect timely repairs. Therefore, researchers have developed approaches to identify these impacts to railroad bridges. Some recent approaches use machine learning to more effectively identify impacts from the sensor data. Typically, the collected sensor data is transmitted to a central location for processing. However, the challenge with this centralized approach is that the transfer of data to a central location can take considerable time, which is undesirable for time-sensitive events like impact detection that require rapid assessment and response to potential damage. To address the challenges posed by the centralized approach, this study develops a framework for edge implementation of machine learning predictions on wireless smart sensors. Wireless sensors are used because of their ease of installation and lower costs compared to their wired counterparts. The framework is implemented on the Xnode wireless smart sensor platform, thus bringing artificial intelligence models directly to the sensor nodes and eliminating the need to transfer data to a central location for processing. This framework is demonstrated using data obtained from events on a railroad bridge near Chicago; results illustrate the efficacy of the proposed edge computing framework for such time-sensitive structural health monitoring applications.

An application of CO2/HCO3--free solution (Zero-CO2) did not increase intracellular pH (pHi) in ciliated human nasal epithelial cells (c-hNECs), leading to no increase in the beating frequency (CBF) or bend distance (CBD, an index of amplitude). This study demonstrated that the pHi of the c-hNECs expressing carbonic anhydrase IV (CAIV) is high (7.64), while that of the ciliated human bronchial epithelial cells (c-hBECs) expressing no CAIV is low (7.10). Upon applying Zero-CO2, an extremely high level of pHi caused the pHi, CBF and CBD to decrease, while a low level of pHi caused them to increase. The high pHi was generated by a high rate of HCO3- influx via interac-tions between CAIV and Na+/HCO3- cotransport (NBC) in c-hNECs. An NBC inhibitor (S0859) decreased the pHi and CBF, and Zero-CO2 application increased the CBF in S0859-treated c-hNECs. In conclusion, the interactions of CAIV and NBC maximize the HCO3- influx to increase the pHi in c-hNECs. This novel mechanism causes the pHi to decrease, leading to no increase in CBF and CBD in c-hNECs upon Zero-CO2 application, and appears to play a crucial role in maintaining pHi, CBF and CBD in c-hNECs periodically exposed to air (0.04% CO2) with respiration.

In this paper, a continuous power management for a decentralized DC microgrid (DCMG) is proposed to achieve voltage regulation and power balance even under system uncertainty and voltage sensor failure. The DCMG system achieves a continuous power management through only the primary controller to reduce the computational burden of each power agent. To enhance the reliability and resilience of the DCMG system under voltage sensor failure, a DC bus voltage (DCV) sensor fault detection algorithm is proposed. In this algorithm, the DCV sensor failure is detected by comparing the measured DCV with the estimated DCV. When the power agent identifies the DCV sensor failure, it changes the operation properly according to the proposed control mode decision algorithm to maintain the stability of the DCMG system. When uncertain conditions such as the power variation of the distributed generations, sudden grid disconnection, DCV sensor failure, electricity price change, and critical battery status occur, the DCMG system is changed to transitional operation modes. These transitional operation modes are employed to transmit the power agent information to other agents without digital communication links (DCLs) and to accomplish power sharing even under such uncertain conditions. In the transitional operation modes of the DCMG system, the DCV levels are temporarily shifted to an appropriate level, enabling each power agent to detect the uncertainty conditions, and subsequently to determine its operation modes based on the DCV levels. Simulation and experimental results under different test conditions confirm the reliability and effectiveness of the proposed control scheme.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

In recent years, Edge Intelligence (EI) has emerged, combining edge computing with AI, specifically deep learning, to run AI algorithms directly on edge devices. In practical applications, EI faces challenges related to computational power, power consumption, size, and cost, with the primary challenge being the trade-off between computational power and power consumption. This has rendered traditional computing platforms unsustainable, making heterogeneous parallel computing platforms a crucial pathway for implementing EI. In our research, we leveraged the Xilinx Zynq 7000 heterogeneous computing platform, employed High-Level Synthesis (HLS) for design, and implemented two different accelerators for LeNet-5 using loop unrolling and pipelining optimization techniques. The experimental results show that when running at a clock speed of 100 MHz, the PIPELINE accelerator, compared to the UNROLL accelerator, experiences an 8.09% increase in power consumption but speeds up by 14.972 times, making the PIPELINE accelerator superior in performance. Compared to the CPU, the PIPELINE accelerator reduces power consumption by 91.37% and speeds up by 70.387 times, while compared to the GPU, it reduces power consumption by 93.35%.This study provides two different optimization schemes for edge intelligence applications through design and experimentation, and demonstrates the impact of different quantization methods on FPGA resource consumption. These experimental results can provide a reference for practical applications, thereby providing a reference hardware acceleration scheme for edge intelligence applications.

The design of curved surface sliders (CSS) based on the elastic response spectrum is done by iteration to find the combination of friction coefficient and displacement capacity which satisfies the condition that the maximum horizontal CSS force is equal to the horizontal force of the structure. Although this CSS design is valid it does not necessarily minimize structural acceleration. This paper therefore describes the optimum CSS design for minimum structural acceleration. All valid CSS designs and the optimum CSS design are represented by their associated trajectory in the elastic response spectrum plane which visualizes the optimization problem. The results demonstrate that the optimum CSS design is not obtained at maximum tolerated effective damping ratio. The subsequent sensitivity analysis describes how much the structural acceleration increases if the actual friction coefficient of the real CSS deviates from its optimum design value. The analysis points out that the increase in structural acceleration is approximately one order of magnitude smaller than the deviation in friction. The sensitivity data may be used by structural engineer to determine tolerable deviations in friction coefficient which still results in acceptable structural accelerations.

Low-frequency electromagnetic induction (EMI) is a non-invasive geophysical method that is based on the induction of electromagnetic (EM) waves into the subsurface to quantify changes in electrical conductivity. In this study we present an open (design details and software are accessible) and modular system for the collection of EMI data. The instrument proposed allows to adjust the separations between the transmitter and up to four receiving antennas as well as the acquisition frequency (in the range between 3 and 50 kHz) to permit measurements with variable depth of investigation. The sensor provides access to raw data and the software described in this study allows control of the signal processing chain. The design specifications permit apparent conductivity measurements in the range of between 1 mS/m and 1000 mS/m, with a resolution of 1.0 mS/m and with a sampling rate of up to 10 samples per second. The sensor allows for a synchronous acquisition of a time stamp and a location stamp for each data sample. The sensor has a mass of less than 5 kg, is portable and suitable for 1-person operation, provides 4 hours of operation time on one battery charge, and provides sufficient rigidity for practical field operations.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

Recently, SMR (Small Modular Reactor) is expected to be able to operate flexibly in conjunction with a high renewable energy penetration grid as a result of improved safety and easy power control compared to large nuclear power plants. SMRs such as South Korea’s System-integrated Modular Advanced ReacTor (SMART) are designed to use canned motors (CMs) for their reactor coolant pumps (RCPs) to enhance safety. The CMs passively enhance the reactor’s safety by preventing leakage of radioactive reactor coolant. However, with motor sizes designed to be as small as possible, and the increased air gap of CMs between stator and rotor, starting torque may be insufficiently small compared to that of similar sized induction motors (IMs). Thusly, CMs may require variable frequency drives (VFDs) to start. This paper compares the torque characteristics of CMs with those of IMs for SMART’s RCPs. ETAP is then used to perform motor starting analysis for CMs started with and without VFDs. The results are presented and analyzed to find out if the VFDs deal with the CM starting torque issue.

Background: Fetal overgrowth is related to many perinatal complications including stillbirth, cesarean section, maternal and neonatal injuries, and shoulder dystocia. It is related to maternal diabetes, obesity, and gestational weight gain, but also happens in low-risk pregnancies. There is ongoing discussion regarding definitions, methods of detection, and classification. The method used for detection is of crucial importance as it draws a line between those at risk and low-risk populations. Methods: In this a narrative review of relevant evidence identified through PubMed search with one of the general terms (macrosomia, large-for-gestational-age) combined with the outcome of interest. Results: This revive summarizes evidence on the relation of fetal overgrowth with stillbirth, cesarean sections, shoulder dystocia, anal sphincter injury, and hemorrhage. Customized growth charts help to detect mothers and fetuses at risk of those complications. Relations between fetal overgrowth and diabetes, maternal weight, and gestational weight gain. Conclusions: a substantial proportion of complications are an effect of the fetus growing above its potential and should be recognized as a new dangerous condition of Fetal Growth Acceleration

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

This paper introduces a novel decision-making approach grounded in insights into human visual perception of change. Modern technologies such as internet of things (IoT) provide us with large amounts of sensor data that need to be processed in real time and decisions made with a high degree of accuracy and reliability. Artificial intelligence (AI) methods are welcome in this context and need to be upgraded to meet actual challenges. While modern computing capabilities facilitate rapid data processing, the real-time demands of vast sensor data necessitate swift responses across the cyber chain, often leading to compromises in solution quality to circumvent combinatorial search complexities. Determining the adequacy of a solution entails varied approaches, often relying on heuristic methodologies. We illustrate our original approach with an example of a selected detail of a differential evolution algorithm, where we have to make a decision to adopt the best solution so far. We propose an approach inspired by human perceptual features that exploits the Weber-Fechner law to emulate human judgements, and offers a promising way to improve decision making in AI applications and real-time requirements fulfillment. Our proposed methodology demonstrates applicability across diverse AI scenarios involving numerical data, effectively mirroring human perception abilities.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

We present a Machian model of Quantum Cosmology with full dark matter and light speed expansion and rotation. During galaxy formation and evolution, fraction of dark matter transforms to visual matter with a relation of the form, m_vis = constant * (m_dark)^2/3. Using this relation and replacing MOND’s ‘critical acceleration’ with “current cosmic maximum angular acceleration”, galactic flat rotation speed range of (50 to 500) km/sec can be fitted well. Estimated flat rotation speeds of DD168, Milky Way and UGC12591 are 49.96 km/sec, 199.66 km/sec and 521.75 km/sec respectively. Based on these striking coincidences, it is possible to say that, MOND’s approach is implicitly connected with cosmological estimation of 95% invisible matter. Considering galactic total matter and current cosmic maximum angular acceleration, galactic working radii, angular velocity and visual matter density can be estimated. Even though, this model is free from ‘big bang’, ‘inflation’, ‘dark energy’, ‘flatness’ and ‘red shift’ issues, at 2.722 K, estimated present Hubble parameter is 66.24 km/sec/Mpc, cosmic radius is 146.3 times the Hubble radius, angular velocity is 146.3 times lower than the Hubble parameter and cosmic age is 146.3 times the Hubble age. With future observations and advanced telescopes, it may be possible to see far distant galaxies and very old stars far beyond the current observable cosmic radius.

Conceiving vacuum energy as gravitational particles subject to Heisenberg’s energy-time uncertainty, modelled as dipoles in a fluidal space at thermodynamic equilibrium, and interpreting the Bekenstein-Hawking entropy as the effective amount of spins of those dipoles enclosed within the event horizon of the universe, allows the calculation of Milgrom’s acceleration constant. The result is a quantum mechanical interpretation of gravity, and dark matter in particular.

Based on the need for real-time sag monitoring of Overhead Power Lines (OPL) for electricity transmission, this article presents the implementation of a hardware and software system for online monitoring of OPL cables and cable sag determination. The mathematical model based on differential equations and the methods of algorithmic calculation of OPL cable sag are presented. Considering that, based on the mathematical model presented, the calculation of OPL cable sag can be done in different ways depending on the sensors used, and the presented application uses a variety of sensors. Therefore, a direct calculation is made using one of the different methods. Subsequently, the verification relations are highlighted directly and, respectively, the calculation by the alternative method, which uses another group of sensors, to generate both a verification of the calculation and the functionality of the sensors, thus obtaining a defect observer of the sensors. The hardware architecture of the OPL cable online monitoring application is presented, together with the main characteristics of the sensors and communication equipment used. The configurations required to transmit data using the ModBUS and ZigBee protocols are also presented. The main software modules of the OPL cable condition monitoring application are described, which ensure the monitoring of the main parameters of the power line and the visualisation of the results both on the electricity provider's intranet using a web server and MySQL database, and on the Internet using an Internet of Things (IoT) server. This categorisation of the data visualisation mode is done in such a way as to ensure a high level of cyber security. Starting from the mathematical model of the OPL cable sag calculation, it goes through the stages of creating such a monitoring system, from the numerical simulations carried out using Matlab to the real-time implementation of this monitoring application. The main modules of the application software are: the software module for reading quantities from the sensor network through a ModBUS Input/Output (I/O) server, the software module for real-time calculation of the OPL cable sag, the software module for read/write operations based on MySQL type data, the software module for transferring data to the user's intranet through a web server, and the software module for viewing data by authorised users based on user and password through an IoT server. The development software environments used are Matlab and Laboratory Virtual Instrument Engineering Workbench (LabVIEW).

Aquifer karstic structures, due to their complex nature, present significant challenges in accurately mapping their intricate features. Traditional methods often rely on invasive techniques or sophisticated equipment, limiting accessibility and feasibility. In this paper, we propose a new approach to non-invasive, low-cost 3D reconstruction using a camera that observes the light projection of a simple diving lamp. Our method capitalizes on the principles of structured light, leveraging the projection of light contours onto the karstic surfaces. By capturing the resultant light patterns with a camera, we reconstruct three-dimensional representations of the structures. The simplicity and portability of the equipment required make this method highly versatile, enabling deployment in diverse underwater environments. We validate our approach through extensive field experiments conducted in various aquifer karstic settings. The results demonstrate the efficacy of our method in accurately delineating intricate karstic features with remarkable detail and resolution. Furthermore, the non-destructive nature of this technique minimizes disturbance to delicate aquatic ecosystems while providing valuable insights into the subterranean landscape. This innovative methodology not only offers a cost-effective and non-invasive means of mapping aquifer karstic structures but also opens avenues for comprehensive environmental monitoring and resource management. Its potential applications span hydrogeological studies, environmental conservation efforts, and sustainable water resource management in karstic terrains worldwide.

Evaluation of the effects of a high-frequency acceleration (HFA) device on patient pain response to orthodontic forces. A multi-centered trial investigating pain sensitivity to orthodontic forces on 75 subjects at 4 study centers. Subjects underwent clear aligner treatment, with or without adjunctive HFA and documented their pain intensity using the validated NRS10 numeric rating scale. In-Office and At-Home ratings were measured separately for each subject for immediate and extended effect evaluations. Use of HFA devices in conjunction with clear aligner orthodontic treatment demonstrated significant reduction in subjects’ recorded pain ratings vs controls within 5 minutes of aligner exchange, (p = 0.006) and significant reduction in recorded pain ratings vs controls over a 7-day period following aligner exchange (p = 0.018). A 99.6% daily compliance rate with at home use of the HFA device was recorded for all subjects in the study. HFA significantly reduces pain attributed to orthodontic force. HFA delivers clinically significant immediate pain relief, and clinically significant extended pain relief over the 7 days following adjustment.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

The heat and matter transfer during glucose catabolism in living systems and their relation with entropy production are a challenging subject of the classical thermodynamics applied to biology. In this respect, an analogy between mechanics and thermodynamics has been performed via the definition of the entropy density acceleration expressed by the time derivative of the rate of entropy density and related to heat and matter transfer in minimum living systems. Cells are regarded as open thermodynamic systems that exchange heat and matter resulting from irreversible processes with the intercellular environment. Prigogine’s minimum energy dissipation principle is reformulated using the notion of entropy density acceleration applied to glucose catabolism. It is shown that, for out-of-equilibrium states, the calculated entropy density acceleration is finite and negative and approaches as a function of time a zero value at global thermodynamic equilibrium for heat and matter transfer independently of the cell type and the metabolic pathway. These results could be important for a deeper understanding of entropy generation and its correlation with heat transfer in cell biology with special regard to glucose catabolism representing the prototype of irreversible reactions and a crucial metabolic pathway in stem cells and cancer stem cells.

An optical fiber scale sensor based on the detection principle of surface plasmon resonance (SPR) was developed for the rapid, high-sensitivity real-time evaluation of scale precipitation from geothermal fluids. The optical fiber SPR scale sensor was fabricated by depositing a gold thin film on the surface of an optical fiber with an exposed core. The optimal gold film thickness of the sensor was determined to be 30 nm, which achieved a refractive index sensitivity of 2140 nm per refractive index unit. A field test was conducted using geothermal brine from the Obama Binary Geothermal Power Plant in Unzen, Nagasaki Prefecture. A conventional optical fiber scale sensor and the SPR sensor were simultaneously assessed using raw and pH-adjusted brines. For the SPR sensor, a peak shift of 0.27 nm/min was observed at a response time of 1 min, whereas no change in transmittance was observed for the conventional sensor until 180 min. After the experiments, scanning electron microscopy–energy-dispersive spectroscopy analysis was conducted on the sensors, and findings showed that the deposition of Mg–SiO2 scale did not significantly differ between the two sensors. The developed SPR sensor achieved faster scale precipitation detection (tens of minutes to hours) than the conventional sensor.

in our increasingly interconnected world, sensor networks are critical in gathering and sending data for various applications, from environmental monitoring and industrial automation to healthcare and smart cities. However, as sensor networks expand in importance, so does the need to solve the multidimensional concerns of security, privacy, and forensics. This article explores the complex world of sensor network security, the delicate balance between data privacy and utility, and the emerging area of sensor network forensics. This article focuses on risk assessment of a network.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

Acceleration parameters in sit-to-stand (STS) movements are useful for measuring lower-limb function in older adults. The purpose of this study was to examine the relationship between acceleration in STS movements and physical function and the test-retest reliability of acceleration parameters in older adults. We performed cross-sectional analyses on 244 older adults including 107 men (mean age:77.4±4.7) and 137 women (mean age: 75.6±5.3). Four acceleration parameters were measured in STS movements: maximum acceleration (MA), maximum velocity (MV), maximum power (MP), and stand-up time (ST). Good intraclass correlation coefficients (ICC>0.70) were observed for all parameters. For the acceleration parameters, MA, MV, and MP were relatively strongly associated with the 5-time STS test (men: r=-0.36~-0.47; women: r=-0.37~-0.45) and the Timed up and Go test (men: r=-0.39~0.47, women: r=-0.43~-0.51): MP was also strongly associated with grip strength (men: r=0.48, women: r=0.43). All acceleration parameters were poorer in participants reporting mobility limitations than in those reporting no mobility limitations. These findings support the usefulness of sensor-based STS measurement. The system is expected to be useful in various settings where care prevention is addressed.

A Mw7.8 earthquake struck Turkey on February 6, 2023, causing severe casualties and economic losses. This paper investigates the characteristics of strong ground motion and seismogenic fault of the earthquake. We collected and processed the strong ground motion records of 379 stations using Matlab, SeismoSignal and Surfer software, and obtained the peak ground acceleration (PGA) contour map. We analyzed the near-fault effect, the fault locking segment effect and the trampoline effect of the earthquake based on the spatial distribution of PGA, the fault geometry and slip distribution. We found that the earthquake generated a very strong ground motion concentration effect in the near-fault area, with the maximum PGA exceeding 2000cm/s2. However, the presence of fault locking segments influenced the spatial distribution of ground motion, resulting in four significant PGA high-value concentration areas at a local dislocation, a turning point and the end of the East Anatolian Fault. We also revealed for the first time the typical manifestation of the trampoline effect in this earthquake, which was characterized by a large vertical acceleration with the positive direction significantly larger than the negative direction. This paper provides an important reference for understanding the seismogenic mechanism, damage mode, characteristics and strong earthquake law of Turkey earthquake.

The study put forward a data fusion approach for urban remote sensing that combines SAR (Synthetic Aperture Radar) and optical satellite data. By integrating datasets from different sensors and spatial-temporal scales, the technique aims to extract more accurate information. The fusion approach utilizes two methods: feature-based fusion, where relevant features are extracted and fused, and simple layer stacking (SLS), where the original datasets are directly stacked as multiple layers. This study extracted features using SAR textures (using Sentinel-1) and modified indices (using Landsat-8), and then classified these features using an XGBoost algorithm implemented in Python and Google Earth Engine. Researchers examined five cities, each representing a distinct climatic zone and urban dynamic: Cape Town, Guangzhou, Los Angeles, Mumbai, and Osaka. An accuracy assessment was conducted using random validation points, achieving an overall accuracy of 89.5% using the proposed MSFI method. A comparison was also performed with three well-known global products. The proposed approach, outperformed all three global products achived 89% accuracy while ESA (84%), ESRI (81%) and Dynamic World (82%). Additionally, Land surface temperature analysis was accomplished to investigate the relationship between extracted UIS and Land Surface Temperature (LST) across selected cities to show the practical use of proposed MSFI method. Los Angeles, a warm temperate city, showed the highest LST among all five cities. The datasets, along with the GEE and Python codes, are available at https://github.com/mnasarahmad/sls.

The physics of Hubble's law, motivated by the anomalous acceleration of Pioneer 10/11, suggests that the Hubble constant corresponds to a gravitational field of the Universe. The Hubble constant inferred from Pioneer 10/11 data is $\sim 69$ km/s/Mpc. The anomalous acceleration of Pioneer 10/11 can be interpreted as an observational evidence for Mach's principle. The redshift is an apparent value. Its intrinsic value has a limit resulting to $v

Nondipole terms in the atom-laser interaction arising due to the presence of a magnetic component in an electromagnetic wave and its inhomogeneity lead to nonseparability of the center-of-mass (CM) and electron variables in the neutral atom and, as a consequence, to its acceleration. We investigate this effect as well as the accompanying excitation and ionization processes for the hydrogen atom in strong (1012 - 2×1014 W/cm2) linearly polarized short-wavelength (5eV ≲ℏω≲ 27 eV) electromagnetic pulses of about 8 fs duration. The study has been carried out within the framework of a hybrid quantum-quasiclassical approach in which the coupled time-dependent Schrödinger equation for an electron and the classical Hamilton equations for the CM of an atom are simultaneously integrated. Optimal conditions with respect to the frequency and intensity of the electromagnetic wave for the acceleration of atoms without their noticeable ionization are found in the analyzed region.

The crystallization conditions from the solution play an important role in determining the mor-phology, phase composition, and photovoltaic properties of perovskite films. Post-processing of the obtained films can have a crucial role in increasing the grain size of perovskite and enhancing its crystallinity. It has been shown that the formation of crystal nuclei can be utilized to accelerate crystallization. In this case, crystallization occurs through the growth of seed crystals created in the solution, enabling the formation of relatively large crystals. For the deposition of CH3NH3PbI3 hybrid halide perovskite films from a solution of the perovskite in dimethylformamide the spin coating echnique was employed. Pre-crystallization was achieved by heating films at a temperature of 100 or 110 °C. The dissolution process involved adding a drop of dimethylformamide onto the substrate surface and allowing it to partially dis-solve the perovskite for 30-40 seconds. Subsequently, residual solvent was removed through spin coating. The recrystallization process was carried out by heating films at the temperature range of 80 to 130 °C. The morphological analysis of the perovskite film surfaces after recrystallization at tem-peratures ranging from 80 to 130 °C was performed. The infrared transmission spectra of the obtained perovskite films were investigated, and their light absorption characteristics were studied through transmission spectra. The perovskite structure in the obtained films was con-firmed by the peaks observed in the X-ray diffraction patterns.

In this paper, we implement a new method binary Particle Swarm Optimization (PSO) for solving the kidney exchange problem, which will improve the future decisions of kidney exchange programs. Because using a kidney exchange, we can help incompatible patient-donor couples to swap donors to receive a compatible kidney. Kidney paired donation programs provide an innovative approach for increasing the number of available kidneys. Further, we implementing binary particle swarm optimization in parallel with MATLAB with one, two, three and four threads and from the computations point of view, the authors compare the performance to reduce the running time for kidney exchange to match patients as fast as possible to help clinicians. Moreover, implementing binary particle swarm optimization in solving the kidney exchange problem is an effective method. The obtained results indicate that binary PSO outperforms other stochastic-based methods such as genetic algorithm, ant lion optimization, and efficient the number of resulting exchanges.

Evaluation of the effect of a high frequency acceleration device on clear aligner exchange intervals and treatment time required to achieve prescribed tooth movements. Sixteen subjects with similar Class I malocclusions, 5mm or less crowding, and treated with Invisalign were divided into two groups. Group 1 (experimental; N=8) underwent aligner treatment in conjunction with daily use of the high frequency acceleration device and exchanged aligners every 5 days. Group 2 (controls; N=8) underwent aligner treatment without use of the device and exchanged aligners every 14 days according to the manufacturer's recommended interval. All subjects were treated by one investigator, and results were evaluated by both; total number of aligners used, and number of refinements required, prior to final Vivera retention scan. A significant decrease in both treatment time, and number of aligners required to complete treatment was observed by experimental subjects as compared to controls. In addition, no refinements were required by experimental subjects, whereas 6 of 8 of the control subjects required 1 or more refinements. Use of the high frequency acceleration device in conjunction with Invisalign treatment resulted in more predictable tooth movement and a significant decrease in the length of treatment.

This review article explores the innovative application of software sensors for monitoring and controlling biosystems, emphasizing their advantage in managing the complexities of various biological processes. Biosystems—from cellular interactions to ecological dynamics—are characterized by intrinsic nonlinearity, temporal variability, and uncertainty, posing significant challenges for traditional monitoring approaches. A critical challenge highlighted is that what is typically measurable may not align with what needs to be monitored. Software sensors bridge this gap by combining hardware sensor data with advanced computational modelling techniques to indirectly infer hard-to-measure target variables, such as stress level, animal and human health indicators, and chemical soil properties. The article outlines advancements in sensor technologies and their integration into model-based monitoring and control systems, leveraging the capabilities of Internet of Things (IoT) devices, wearables, remote sensing, and smart sensors. It provides an overview of common methodologies for designing software sensors, focusing on the modelling process. The discussion contrasts hypothetico-deductive (mechanistic) models with inductive (data-driven) models, illustrating the trade-offs between model accuracy and interpretability. Specific case studies are presented, showcasing software sensor applications such as the use of Kalman filter in greenhouse control, remote detection of soil organic matter, and sound recognition algorithms for early detection of respiratory infections in animals. Key challenges in designing software sensors, including the complexity of biological systems, inherent temporal and individual variabilities, and the trade-offs between model simplicity and predictive performance, are also discussed. This article positions software sensor as remarkable tool for advancing biosystem management, driving forward the potential for sustainable practices in various sectors such as agriculture, healthcare, and environmental monitoring.

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

it has been just over three years since SARS-CoV-2 viral infection was first known as causing severe acute and highly transmissible respiratory syndrome coronavirus. During one of the worst global pandemics of the last century, caused by the COVID-19 disease, under the persistent immune pressure exerted by the newest vaccines, the SARS-CoV-2 virus is fastly mutating and becoming less severe, but more contagious. On the other hand, some studies [1,2,3] indicate that the elderly COVID-19 patients or those who have reported a virulent episode of this infection, experience some long-lasting neurological complications, including encephalopathy, encephalitis, cerebrovascular disease, Parkinson’s disease (PD), Alzheimer’s disease (AD) and prion disease (PrD). So, there are several recent reports of patients [4,5] developing PrD following the SARS-CoV-2 infection, but, to the best of our knowledge, this is the first case reported in Italy on an association of the PRNP E200K somatic mutation with gCJD. The rising global prevalence neurodegenerative complications following COVID-19 disease adds urgency to the study of this potential relationship.

The integration of Wireless Sensor Networks (WSNs) into agricultural areas has had a significant impact and has provided new, more complex, efficient, and structured solutions for enhancing crop production. This research reviews the role of Wireless Sensor Networks (WSNs) in monitoring the macro-nutrient content of plants. The review study focuses on identifying the types of sensors used to measure macro-nutrients, determining sensor placement within agricultural areas, implementing wireless technology for sensor communication, and selecting device transmission intervals and ratings. The study of NPK (Nitrogen, Phosphorus, Potassium) monitoring using sensor technology in precision agriculture is of high significance in efforts to improve agricultural productivity and efficiency. In addition to fostering technological innovations and precision farming solutions, in future this research aims to increase agricultural yields, particularly by enabling the cultivation of certain crops in locations different from their original ones.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

The integration of nanoparticles in biomedical applications requires precise analysis of their photochemical properties. However, computational simulations of these properties are computationally intensive, hindering rapid advancement. This study explores the implementation of Graphics Processing Unit (GPU) acceleration techniques to enhance computational efficiency in analyzing nanoparticle photochemistry within bioinformatics frameworks.By leveraging GPU parallel processing capabilities, we developed optimized algorithms for photochemical property simulations, achieving significant speedup over traditional Central Processing Unit (CPU)-based methods. Our GPU-accelerated framework demonstrated substantial performance gains in computing photochemical properties, such as absorption spectra and energy transfer rates.

Spiking neural networks (SNNs) promise to perform tasks currently done by classical artificial neural networks (ANNs) faster, in smaller footprints and using less energy. Neuromorphic processors are set out to revolutionize computing at a large scale, but the move to edge-computing applications calls for finely-tuned custom implementations to keep pushing towards more efficient systems. To that end, we have examined the architectural design space for executing spiking neuron models on FPGA platforms, focusing on achieving ultra-low area and power consumption. This work presents an efficient clock-driven spiking neuron architecture used for the implementation of both fully-connected cores and 2D convolutional cores, which rely on deep pipelines for synaptic processing and distributed memory for weight and neuron states. With them, we have developed an accelerator for an SNN version of the LeNet-5 network trained on the MNIST dataset. At around 5.5 slices/neuron and only 348 mW, it is able to use 33% less area and 4 times as less power per neuron as current state-of-the-art implementations while keeping low simulation step times.

This paper is intended at highlighting the main mechanical parameters controlling the behavior of the so-called "acceleration-sensitive" Non-Structural Components (NSCs). In the first part a short review of the current state of knowledge and the critical issues related to the prediction of the seismic response of NSCs is reported. Then, the paper presents the results of a numerical parametric analysis intended to capture the key features of the dynamic response of a two-degree-of-freedom (2DOF) system which is supposed to be representative of both the main structure and the "non-structural" component (NSC). Particularly, it allows to simulate the coupled behaviour of both main structure and NSC and evaluating their response. The main parameters controlling the dynamic response of NSCs emerge from this study, which could pave the way towards formulating more mechanically consistent relationships for evaluating the maximum accelerations induced by seismic shakings on NSCs.

Smartphones, smartwatches, fitness trackers, and ad-hoc wearable devices are being increasingly used to monitor human activities. Data acquired by the hosted sensors are usually processed by machine-learning-based algorithms to classify human activities. The success of those algorithms mostly depends on the availability of training (labeled) data that, if made publicly available, would allow researchers to make objective comparisons between techniques. Nowadays, publicly available data sets are few, often contain samples from subjects with too similar characteristics, and very often lack of specific information so that is not possible to select subsets of samples according to specific criteria. In this article, we present a new smartphone accelerometer dataset designed for activity recognition. The dataset includes 11,771 activities performed by 30 subjects of ages ranging from 18 to 60 years. Activities are divided in 17 fine grained classes grouped in two coarse grained classes: 9 types of activities of daily living (ADL) and 8 types of falls. The dataset has been stored to include all the information useful to select samples according to different criteria, such as the type of ADL performed, the age, the gender, and so on. Finally, the dataset has been benchmarked with two different classifiers and with different configurations. The best results are achieved with k-NN classifying ADLs only, considering personalization, and with both windows of 51 and 151 samples.

Separase is a key cysteine protease to separate sister chromatids through digestion of cohesion ring that inhibits chromosome segregation as trigger of metaphase–anaphase transition in eukaryotes and highly regulated its activity by binding with securin and cyclinB-CDK1 complex. Those bindings prevent proteolytic activity of separase until the onset of anaphase. Chromosome missegregation and aneuploidy are frequently observed in malignancies. However, there are some difficulties for biochemical examinations due to instability of separase in vitro and a few spatiotemporal resolution approaches monitoring live separase activity throughout mitotic processes. Here we have developed FRET-based molecular sensors including GFP variants with separase cleavable sequences as donor and covalently attached fluorescent dye as acceptor molecules applicable to conventional live cell imaging and flow cytometric analysis because of efficient live cell uptake. We investigated performance of equivalent molecular sensors localized or not localized inside nucleus under cell cycle control using flow cytometry. Synchronized cell cycle progression rendered significant separase activity detections in both molecular sensors. We obtained consistent outcomes with localized molecular sensor introduction and cell cycle control by fluorescent microscopic observations. We thus established live cell separase activity monitoring systems specifically or statistically that could lead to elucidate separase properties in detail.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Quasi-bound state in the continuum (QBIC) can effectively enhance the interaction of terahertz (THz) wave with matters due to the tunable high-Q property, which has a strong potential application in detection of low-concentration biological samples in the THz band. In this paper, a novel THz metamaterial sensor with a double-chain separated resonant cavity structure based on QBIC is designed and fabricated. The process of excitation of the QBIC mode is verified and the structural parameters are optimized after considering the ohmic loss by simulations. The simulated refractive index sensitivity of the sensor is up to 544 GHz/RIU, much higher than those of recently reported THz metamaterial sensors. Sensing sensitivity of the proposed metamaterial sensor is confirmed in experiment by detecting low-concentration lithium citrate (LC) and bovine serum albumin (BSA) solutions. The limits of detection (LoDs) are obtained to be 0.0025 mg/mL (12 μM) for LC and 0.03125 mg/mL (0.47 μM) for BSA, respectively, both of which excel over most of reported results in previous studies. These results indicate that the proposed THz metamaterial sensor has excellent sensing performances and can well be applied to the detection of low concentration biological samples.

We present a data-driven, in situ proximal multi-sensor digital soil mapping approach to develop digital twins for multiple agricultural fields. A novel Digital Soil CoreTM (DSC) Probe was engineered that contains seven sensors, each of a distinct modality, including sleeve friction, tip force, dielectric permittivity, electrical resistivity, soil imagery, acoustics, and visible and near-infrared spectroscopy. The DSC System integrates components the DSC Probe, DSC software, and deployment equipment to sense soil characteristics at a high vertical spatial resolution (mm scale) along in situ soil profiles up to a depth of 120 cm in about 60 sec. The DSC Probe in situ proximal data are harmonized into a data cube providing vertical high-density knowledge associated with physical-chemical-biological soil conditions. In contrast, conventional ex situ soil samples derived from soil cores, soil pits, or surface samples analyzed using laboratory and other methods are bound by substantially coarser spatial resolution and multiple compounding errors. Our objective was to investigate the effects of mismatched scale between high-resolution in situ proximal sensor data and coarser resolution ex situ soil laboratory measurements to develop soil prediction models. Our study was conducted in central California soil in almond orchards. We collected DSC sensor data and spatially co-located soil cores that were sliced into narrow layers for laboratory-based soil measurements. Partial Least Squares Regression (PLSR) cross-validation was used to compare results testing four data integration methods. Method A reduced the high-resolution sensor data to discrete values paired with layer-based soil laboratory measurements. Method B used stochastic distributions of sensor data paired with layer-based soil laboratory measurements. Method C allocated the same soil analytical data to each one of the high-resolution multi-sensor data within a soil layer. Method D linked the high-density multi-sensor soil data directly to crop responses (crop performance and behavior metrics) bypassing costly laboratory soil analysis. Overall, the soil models derived from Method C outperformed Methods A and B. Soil predictions derived using Method D were most cost-effective for directly assessing soil-crop relationships, making this method well-suited for industrial-scale precision agriculture applications.

The monitoring of maternal and child health, using wearable devices made with wireless sensor technologies, is expected to reduce maternal and child death rates. Wireless sensor technologies have been used in wireless sensor networks to enable the acquisition of data for monitoring machines, smart cities, transportation, asset tracking, and tracking of human activity. Applications based on wireless body area network (WBAN) have been used in healthcare for measuring and monitoring of patient health and activity through integration with wearable devices. Wireless sensors used in WBAN can be cost-effective, enable remote availability, and can be integrated with electronic health record (EHR) management systems. Interoperability of WBAN sensor data with other linked data has the potential to improve health for all, including maternal and child health through the improvement of data access, data quality and healthcare access. This paper presents a survey of the state-of-the-art techniques for managing WBAN sensor data interoperability. The findings in this study will provide reliable support to enable policymakers and health care providers to take action to enhance the use of e-health to improve maternal-child health and reduce the mortality rates of women and children.

The aim of this review is to provide a survey of the recent advances and the main remaining challenges related to the ultrananocrystalline diamond (UNCD) nanowires and other nanostructures which exhibit excellent capability as the core components for many diverse novel sensing devices, due to the unique material properties and geometry advantages. The doping introduced in the gas phase during deposition promotes p-type or n-type conductivity. With the establishment of the UNCD nanofabrication techniques, more and more nanostructure based devices are being explored in measuring basic physical and chemical parameters via classic and quantum methods, as exemplified by gas sensors, ultraviolet photodetectors, piezoresistance effect based devices, biological applications, and nitrogen-vacancy color center based magnetic field quantum sensors. Highlighted finally are some of the remaining challenges and future outlook in this area.

In this study, a novel flexible ethanol gas sensor was created by the deposition of CoFe2O4 (CFO) thin film was on a thin mica substrate using pulsed laser deposition. Transition electron microscopy (TEM) investigations clearly demonstrated the successful growth of CFO on the mica, where a well-defined interface was observed. Ethanol gas-sensing studies showed optimal performance at 200 °C, with the highest response, 19.2, to 100 ppm ethanol. Operating the sensor in self-heating mode under 7 V applied voltage, which was corresponds to a temperature of approximately 200 °C, produced a maximal response to ethanol of 19.2. This aligned with the highest responses observed during testing at 200 °C, confirming the sensor’s accuracy and sensitivity to ethanol under self-heating conditions. In addition, the sensor exhibited good selectivity to ethanol and excellent flexibility; maintaining its high performance after bending and tilting up to 5000 times. As this is the first report on flexible self-heated CFO gas sensors, we believe that this research holds great promise for the future development of high-quality sensors based on this approach.

In order to enhance the comfort of cycling, it is imperative to investigate the effects of vibration on non-motorized bicycle riding from the perspectives of road characteristics and traffic features. Through an analysis of the mechanisms by which road and traffic conditions influence cycling vibrations, 13 influencing factors were identified. Subsequently, the non-motorized bicycle lanes in Wuhan city were selected as the subject of empirical research, where three-axis accelerometers attached to the rider's torso were employed to measure and categorize vibration comfort levels. The experimental road segments were found to exhibit comfort levels falling between slightly uncomfortable and relatively uncomfortable. Further analysis of the influencing factors was conducted using the Random Forest algorithm and Logistic Regression. The results revealed that six factors significantly impact the comfort of cycling: the presence of dedicated non-motorized bicycle lanes, the absence of physical separation between non-motorized and motorized traffic, cycling speed, the number of road surface irregularities, the presence of parking areas within the non-motorized bicycle lane, and the type of non-motorized bicycle. This study provides valuable insights into the factors affecting non-motorized bicycle lane usage and contributes to the refined design of urban non-motorized bicycle infrastructure, thereby facilitating better support for sustainable urban transportation.

The paper briefly reviews the Clifford algebras of space Cl(3,0) and anti-space Cl(0,3) with a particular focus on the paravector representation, emphasizing the fact that both algebras have an isomorphic center represented just by two coordinates. Since the paravector representation allows assigning the scalar element of grade 0 to the time coordinate, we consider the relativity in such two-dimensional spacetime for a uniformly accelerated frame with the constant acceleration 3Hc. Using the Rindler coordinate transformations in two-dimensional spacetime and then applying it to Minkowski coordinates, we obtain the FLRW metric, which in the case of the Clifford algebra of space Cl(3,0) corresponds to the anti-de Sitter (AdS) flat (k=0) case, the negative cosmological term and an oscillating model of the universe. The approach with anti-Euclidean Clifford algebra Cl(0,3) leads to the de Sitter model with the positive cosmological term and the exact form of the scale factor used in modern cosmology.