Hands-on type training of Integrated Computational Materials Engineering (ICME) is characterized by assisted application and combination of multiple simulation software tools and data. In this paper, we present recent experiences in establishing a cloud-based infrastructure to enable remote use of dedicated commercial and open access simulation tools during an interactive on-line training event. In the first part, we summarize the hardware and software requirements and illustrate how these have been met using cloud hardware services, a simulation platform environment, a suitable communication channel, common workspaces and more. The second part of the article focuses (i) on the requirements for suitable on-line hands-on training material and (ii) on details of some of the approaches taken. Eventually, the practical experiences made during three consecutive on-line training courses held in September 2020 with 35 nominal participants each, are discussed in detail.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

This paper numerically investigates a 3D mesh independency study of a straight blade horizontal axis tidal turbine modelled using Computational Fluid Dynamics (CFD). The solution was produced by employing two turbulence models, the standard k-ε model and Shear Stress Transport (SST) in ANSYS CFX. Three parameters were investigated: mesh resolution, turbulence model, and power coefficient in the initial CFD, analysis. It was found that the mesh resolution and the turbulence model affect the power coefficient results. The power coefficients obtained from the standard k-ε model are 15% to 20% lower than the accuracy of the SST model. It can also be demonstrated that the torque coefficient increases with the increasing Tip Speed Ratio (TSR), but drops drastically after TSR = 5 and k-ε model failing to capture the non-linearity in the torque coefficient with the increasing TSR.

Coronaviruses constitute a global threat to human and animal health. It is essential to investigate the long-distance RNA-RNA interactions that approximate remote regulatory elements in strategies, including genome circularization, discontinuous transcription, and transcriptional enhancers, aimed at rapid replication of their large genomes, pathogenicity, and immune evasion. Based on the primary sequences and modeled RNA-RNA interactions of two experimentally de-fined coronaviral enhancers, we detected via in silico primary and secondary structural analysis potential enhancers in various coronaviruses, from the phylogenetically ancient avian IBV to the recently emerged SARS-CoV-2. These potential enhancers possess a core duplex-forming region that could transition between closed and open states, as molecular switches directed by viral or host factors. The open state would permit the enhancer to pair with remote sequences in the viral genome and modulate the expression of crucial genes involved in viral replication and host immune evasion. Consistently, variations in the predicted IBV enhancer region or its distant targets coincide with cases of viral attenuation possibly driven by decreased expression of the ORF3a immune evasion protein. The annotated enhancer sequences could inform structural prediction tools and antiviral interventions if validated experimentally.

The rapid development of three-dimensional (3D) acquisition technology based on 3D sensors provides a large volume of data, which is often represented in the form of point clouds. Point cloud representation can preserve the original geometric information along with associated attributes in a 3D space. Therefore, it has been widely adopted in many scene-understanding-related applications such as virtual reality (VR) and autonomous driving. However, the massive amount of point cloud data aggregated from distributed 3D sensors also poses challenges for secure data collection, management, storage, and sharing. Thanks to the characteristics of decentralization and security nature, Blockchain has a great potential to improve point cloud services and enhance security and privacy preservation. Inspired by the rationales behind Software Defined Network (SDN) technology, this paper envisions SAUSA, a blockchain-based authentication network that is capable of recording, tracking, and auditing the access, usage, and storage of 3D point cloud data sets in their life-cycle in a decentralized manner. SAUSA adopts an SDN-enabled point cloud service architecture which allows for efficient data processing and delivery to satisfy diverse Quality-of-Service (QoS) requirements. A blockchain-based authentication framework is proposed to ensure security and privacy preservation in point cloud data acquisition, storage, and analytics. Leveraging smart contracts for digitizing access control policies and point cloud data on the blockchain, data owners have full control of their 3D sensors and point clouds. In addition, anyone can verify the authenticity and integrity of point clouds in use without relying on a third party. Moreover, SAUSA integrates a decentralized storage platform to store encrypted point clouds while recording references of raw data on the distributed ledger. Such a hybrid on-chain and off-chain storage strategy not only improves robustness and availability but also ensures privacy preservation for sensitive information in point cloud applications. A proof-of-concept prototype is implemented and tested on a physical network. The experimental evaluation validates the feasibility and effectiveness of the proposed SAUSA solution.

In a wireless network, locations of base stations (BSs)/access points (APs)/sensor nodes can be modeled based on stochastic processes, e.g., a Poisson point process (PPP) or a deterministic pattern planned ahead by providers. While deterministic deployment does not provide tractable interference analysis in general, PPP yields tractable analysis for interference. However, PPP allows APs to be deployed very close to each other and gives pessimistic results compared to the field measurements. In this study, in order to address this issue, Lloyd’s algorithm, which functions as a bridge between random and structural APs deployments, is investigated for analyzing coverage probability in a network. The link distance distribution is modeled as a mixture of Weibull distributions and its parameters are obtained by using the expectation-maximization (EM) algorithm for each iteration of Lloyd’s algorithm. The link distance distribution is further utilized for calculating the coverage probability approximately by exploiting the tractability of PPP.

Atta capiguara is a grass-cutting ant species frequently found in Cerrado biome. However, little is known about the giant nest architecture of this ant. In this study, we investigated the architecture of three A. capiguara nests from the fragment of cerrado in Botucatu, São Paulo, Brazil. Casts were made of the nests by filling them with cement to permit better visualization of internal structures such as chambers and tunnels. After excavation, the depth and dimensions (length, width, and height) of the chambers were measured. The results showed the typical shape of Atta capiguara nests consisting of mounds of loose soil with unique features resembling a conic section. The fungus chambers were found outside the apparent main part of the nest and were spaced apart and distributed laterally at ground level. The waste chambers were located beneath the largest mound of loose soil. Both the fungus and waste chambers exhibited a sectoral distribution. Our study contributes to a better understanding of the so far unknown nest architecture of the grass-cutting ant A. capiguara.

Terms related to gradients of scalar fields are introduced as scalar products into the formulation of entropy. A Lagrange density is then formulated by adding constraints based on known conservation laws. Applying the Lagrange formalism to the resulting Lagrange density leads to the Poisson equation of gravitation and also includes terms being related to curvature of space. The formalism further leads to terms possibly explaining nonlinear extensions known from modified Newtonian dynamics approaches. The article concludes with a short discussion of the presented methodology and provides an outlook on other phenomena, which might be tackled using this new approach.

Cloud Computing is a promising and emerging technology that is rapidly being adopted by many IT companies due to a number of benefits that it provides, such as large storage space, low investment cost, virtualization, resource sharing, etc. Users are able to store a vast amount of data and information in the cloud and access it from anywhere, anytime on a pay-per-use basis. Since many users are able to share the data and the resources stored in the cloud, there arises a need to provide access to the data to only those users who are authorized to access it. This can be done through access control schemes which allow the authenticated and authorized users to access the data and deny access to unauthorized users. In this paper, a comprehensive review of all the existing access control schemes has been discussed along with analysis. Keywords: role-based access control, attribute-based access control, attribute-based encryption

Background/Objectives: Peritoneal dialysis as a form of renal function sub-stitution is not as widespread as hemodialysis. However, it has recognized advantages such as preservation of the residual renal func-tion, no need for vascular access , can be performed at home, but requires a proper in-sertion of a peritoneal dialysis (PD) catheter and maintaining its patency. Methods: We presented a 10-year retrospective study on a group of 133 patients hos-pitalized for peritoneal dialysis catheter insertion/replacement. We routinely implant the catheter laparoscopically, but there were cases in which the insertion was performed open route. We analyzed the patient group by age and gender criteria, number of complications and time when they appeared, duration of surgical intervention and the surgical technique used (126 were performed laparoscopically and 7 were inserted via open route). The open technique was performed mainly in patients with contraindications of general anesthesia. Results: We encountered a number of 23 complications in 18 patients, in only 1 case the patient was switched to permanent hemodialysis (at his own wish). We highlighted in the study the indisputable advantages of laparoscopy, supported by the results obtained: correct placement of the catheter, the possibility of adhesiolysis, preservation of the peritoneal surface through minor op-erative trauma, low number of complications(bleeding, migration, hernia 0,8%, leakage 4%, lower than those found in the literature). Even if infection was the most frequent complication (peritonitis 35%, catheter exit site infection 30.4%), only 1 case appered in the pretraining period. All complications were managed by medical treatment or by temporary cessation of peritoneal lavage, except of two cases that required reimplantation of the catheter. Conclusions: Laparoscopic catheter insertion for PD is a safe method, with reduced post-procedural complications, thus ensuring a long duration of the functionality of the catheter.

In factory automation systems, hybrid wired/wireless networks are often deployed to connect devices of difficult reachability such as those mounted on mobile equipment. A widespread version of these networks makes use of Access Points (APs) to implement wireless extensions of Real--Time Ethernet (RTE) networks via the IEEE 802.11 Wireless LAN (WLAN). Unfortunately, APs may introduce random delays in packet forwarding, mainly related to the their internal behaviors (e.g. code processing times) that negatively impact on the whole performance of the automation systems. Consequently, the knowledge of these delays represent a crucial design information. This paper presents an original and effective method to measure the delays introduced by APs, exploiting a hybrid loop-back link and a simple set-up with moderate instrumentation requirements. The method, which requires an initial calibration by means of a reference AP, has been successfully tested on some commercial APs. As it will be shown, the proposed measurement procedure is general and, as such, can be profitably adopted in even different scenarios.

Crop production in Afghanistan suffers from limited phosphorus (P) availability, which severely hinders national agriculture sustainability. This present study hypothesized that deep fertilizer placement could significantly enhance uptake of immobile P and thus tissue P accumulation and crop yield. A two-year pot experiment growing two maize (Zea mays) hybrid cultivars (Xida-789 and Xida-211) was therefore conducted to test these hypotheses under three contrasting fertilizer placement methods (broadcast, side band, and deep band). In doing so, P concentrations in both maize tissues and soils were compared at 45, 60, and 115 days after sowing (DAS) under nine combinations of nitrogen (N) and P fertilizer rates (kg ha-1: N112P45, N112P60, N112P75, N150P45, N150P60, N150P75, N187P45, N187P60, N187P75). Results have shown that deep band placement significantly increased P uptake efficiency, leading to greater P concentration and accumulation in maize tissues compared to other two fertilization methods. This improved P uptake was attributed to several factors associated with deep placement, including reduced P fixation, enhanced root access to P, and moisture availability for P uptake. Additionally, deep band placement combined with higher N application rates (N187 and N150) further enhanced plant P uptake by promoting P availability and utilization mechanisms. Deep band placement also resulted in significantly higher total soil P, Olsen-P, and P use efficiency than broadcast and side band methods, indicating a more efficient P fertilization strategy for maize that can improve growth and yield. This present study also found positive correlations between P concentration in plant organs and soil Olsen-P, highlighting the importance of adequate soil P levels for optimal plant growth. Overall, our results have showed that deep band fertilizer placement emerged as a superior strategy for enhancing P uptake efficiency, utilization, and maize productivity compared to broadcast and side band placement. This approach can potentially optimize P fertilizer utilization, improve maize growth and yield, while minimizing environmental P losses associated with broadcast applications.

Diabetic foot ulcers (DFUs) significantly affect the lives of patients and increase the risk of hospital stay and amputation. We suggest a remote-monitoring platform for better DFU care. This system uses digital health metrics (scaled from 0 to 10, where higher scores indicate a greater risk of slow healing) to provide a comprehensive overview through a visual interface. The platform features smart offloading devices that capture behavioral metrics such as offloading adherence, daily steps, and cadence. Coupled with remotely measurable frailty and phenotypic metrics, it offers an in-depth patient profile. Additional demographic data, wound characteristics, and clinical parameters, such as cognitive function, were integrated, contributing to a comprehensive risk factor profile. We evaluated the feasibility of this platform with 124 DFU patients over 12 weeks; 39% experienced unfavorable outcomes such as dropout, adverse events, or non-healing. Digital biomarkers were benchmarked (0-10), categorized into low, medium, and high risk for unfavorable outcomes, and visually represented using color-coded radar plots. The initial results of case reports illustrate the value of this holistic visualization to pinpoint the underlying risk factors for unfavorable outcomes, including a high number of steps, poor adherence, and cognitive impairment. Although future studies are needed to validate the effectiveness of this visualization in personalizing care and improving wound outcomes, early results in identifying risk factors for unfavorable outcomes are promising.

The Doppler band compensated by the keystone transform (KT) is limited. Therefore, it needs to be used in conjunction with the Doppler ambiguity compensation function to correct the range migration (RM) caused by maneuvering targets with Doppler ambiguity. However, the KT implemented by sinc interpolation suffers from significant performance loss at boundaries of compensation Doppler bands. Additionally, in a multi-target scenario, KT implementation methods occupy high complexity when the Doppler range of targets spans over two compensation Doppler bands. To address aforementioned issues, this study presents a variable Doppler starting point keystone transform (VDSPKT) method, where a new form of ambiguity compensation function is constructed, turning the Doppler starting point of the compensation band in KT variable. Firstly, the position of the compensation Doppler band is changed from fixed to adjustable as needed, enhancing the flexibility of KT. Crucially, the connection points of the compensation Doppler bands in sinc interpolation are reset, avoiding the performance loss at their boundaries. Also, the compensation band is adjusted to cover the narrow Doppler frequency range caused by targets, significantly improving the computational efficiency. Finally, the simulation results demonstrate that the proposed approach effectively addresses the performance degradation and high computational complexity of KT in the aforementioned scenarios, resulting in a computational load reduced by approximately 50% compared to traditional methods.

The prevalence of hepatitis B and delta viruses (HBV/HDV) among people who use drugs (PWUD) remains largely unknown. In the context of one Philadelphia-based harm reduction organization (HRO), this study aimed to assess HBV/HDV prevalence and facilitate linkage to care. Participants completed a demographic HBV/HDV risk factor survey and were screened for HBV and reflexively for HDV if positive for HBV surface antigen or isolated core antibody. Fisher’s exact tests and regression were used to understand relationships between risks and HBV blood markers. Of the 498 participants, 126 (25.3%) were susceptible to HBV, 52.6% had been vaccinated against HBV, and 17.9% had recovered from a past infection. Eleven (2.2%) participants tested positive for isolated HBV core antibody, 10 (2.0%) for HBV surface antigen, and one (0.2%) for HDV antibody. History of incarceration was associated with current HBV infection, while transactional sex and experience of homelessness were predictive of previous exposure. This study found high rates of current and past HBV infection, and a 10% HBV/HDV co-infection rate. Despite availability of vaccine, one quarter of participants remained vulnerable to infection. Findings demonstrate the need to improve low-threshold HBV/HDV screening, vaccination, and linkage to care among PWUD. The study also identified gaps in the HBV/HDV care cascade, including lack of point-of-care diagnostics and lack of support for HROs to provide HBV services.

We generalize the point information gain (PIG) and derived quantities, i.e., point information gain entropy (PIE) and point information gain entropy density (PIED), for the case of the Rényi entropy and simulate the behavior of PIG for typical distributions. We also use these methods for the analysis of multidimensional datasets. We demonstrate the main properties of PIE/PIED spectra for the real data on the example of several images, and discuss further possible utilizations in other fields of data processing.

Extruded polystyrene (XPS) is frequently used in the construction of many different structures. It is therefore necessary to appropriately characterize its mechanical properties to ensure the safety of said structures. Among the available characterization tests, static bending tests are simple and easy to perform; owing to these characteristics, they should be performed more frequently than other tests. However, in static bending tests on XPS, there are several challenges owing to the high flexibility of XPS, and the chosen testing method and sample configuration affect the accuracy of characterization. In this study, three bending properties (Young’s modulus, proportional limit stress, and bending strength) of samples cut from an XPS panel were determined using three-point bending (TPB), four-point bending (FPB), and compression bending (CB) tests with varying sample span/depth ratios, and statistical analyses were performed to determine the relevance of the tests. The experimental results suggest that the TPB and CB tests were more feasible than the FPB test when the span/depth ratio was appropriately determined. However, clear differences were observed in the sample bending properties determined in these tests. In light of these findings, further studies should be conducted to elucidate these differences.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

We report the case of a 61-year-old woman who was referred to the Oral Surgery and Implantology Unit of the University Hospitals of Geneva to take care edentulous sites after dental avulsions of teeth 11 and 21 following traumatic shock due to endotracheal intubation under general anaesthesia. The dental history revealed that the patient had a history of generalized chronic periodontitis that had been treated several years earlier. Treatment consisted, for the first time to our knowledge, of immediate insertion of implants at sites 11 and 21 with simultaneous bone augmentation in a single surgical procedure and immediate restorations.

The task of weakly supervised point cloud semantic segmentation has received widespread attention and also has been widely used in autonomous driving, robotics, and modern industries. Due to the high dimensionality and large volume of point cloud data, many technical difficulties appeal to weakly supervised semantic processing, especially segmentation. However, weakly-supervised schemes usually provide only partial labelling information of the underlying point cloud data and thus need to effectively extract local features, geometric information, and contextual relationships only using these limited labelled data for supervised learning. To improve weakly-supervised semantic segmentation, we propose a novel segmentation network through the boundary-based feature aggregation based on a K-NN algorithm with down-sampling operation, and also introduce the smoothness loss and Siamese loss for effective segmentation. The experiments on public datasets demonstrate that our presented segmentation method exceeds most of the existing fully supervised and weakly-supervised methods in terms of mIoU. Specifically, our network has high segmentation accuracy on the labels of objects with similar geometrical structures, such as ceiling, wall, floor, chair and table, reaching 91.2%, 98.8%, 83.3%, 75.3% and 80.2%, respectively. Extensive experiments also illustrate its robustness, effectiveness, and generalization of the proposed weakly supervised segmentation network.

High dimensional statistical analysis for the yield of large-scale circuits is quite difficult due to expensive simulations, especially for the memory circuits with high sigma requirement (e.g., SRAM). In this paper, we developed an efficient sparse additive model to substitute simulations. To fit high sigma region accurately, the modeling center is moved to near failure boundary searched by scaling the shape of sampling function. To solve the model efficiently, the process variables are grouped by standard cells so that the model can be solved by our developed blockwise greedy algorithm. The experiments on the 28nm memory circuits validate that our method achieves high accuracy and efficiency compared with other state-of-art works.

This paper presents experimental identification and vibration suppression of a flexible manipulator with non-collocated piezoelectric actuators and strain sensors using optimal multi-poles placement control. To precisely identify the system model, a reduced order transfer function with relocated zeros is proposed, and a first-order inertia element is added to the model to compensate the non-collocation. Comparisons show the identified model match closely with the experimental results both in the time and frequency domains, and a fit of 97.2% is achieved. Based on the identified model, a full-state multi-poles placement controller is designed, and the optimal locations of the closed loop poles are determined. The feasibility of the proposed controller is validated by simulations. Moreover, the controller is tested for different locations of the closed loop poles, and an excellent performance of the optimal locations of the closed loop poles is shown. Finally, the effectiveness of the proposed controller is demonstrated by experiments. Results show that the vibrations of the expected modes are significantly diminished. Besides, vibrations of the higher modes are also slightly suppressed. Accordingly, multi-mode vibrations of the manipulator are well attenuated, and the tip displacement converges quickly with the proposed method.

Candida spondylodiscitis (CS) is a rare disease, for which therapeutic option are limited to fluconazole or echinocandins and the treatment should be administered up to 12 months. In case of reduced azole susceptibility, there is a scarcity of therapeutic options with adequate bone penetration and limited toxicity. We report the first case of successful use of rezafungin for a spondylodiscitis due to Candida parapsilosis with reduced susceptibility to azoles. The patient, affected by paraplegia and short bowel syndrome, was diagnosed with CS with culture on vertebral biopsy guided by a 18-FDG-PET/CT scan. He received rezafungin 200 mg weekly for 26 weeks, after 10 weeks of previous antifungal treatment. He had a full clinical, radiologic and biochemical response to the therapy with rezafungin, with no adverse effects. Rezafungin is a promising therapy for Candida osteomyelitis, especially when first line therapies are ineffective or contraindicated.

Aiming at effectively generating safe and reliable motion paths for quadruped robots, a hierar-chical path planning approach driven by dynamic 3D point cloud is proposed in this article. The developed path planning model is essentially constituted of two layers: global path planning layer and local path planning layer. At the global path planning layer, a new method is proposed for calculating terrain potential field based on point cloud height segmentation. Variable step size is employed to improve the path smoothness. At the local path planning layer, a real-time prediction method for potential collision area and a strategy for temporary target point selection is developed. Quadruped robot experiments were carried out in an outdoor complex environment. The experi-mental results verified that, for global path planning, the smoothness of the path is improved and the complexity of the passing ground is reduced. The effective step size is increased by a maxi-mum of 13.4 times, and the number of iterations is decreased by up to 1/6, compared with the traditional fixed step size planning algorithm. For local path planning, the path length is short-ened by 20%, more efficient dynamic obstacle avoidance and more stable velocity planning are achieved by using the improved dynamic window approach (DWA).

In the past twenty years, the IT industry has moved away from using physical servers for workload management to workloads consolidated via virtualization and, in the next iteration, further consolidated into containers. In the next step, container workloads based on Docker and Podman as underlying container technologies were orchestrated/automated via Kubernetes or OpenShift. On the other hand, high-performance computing (HPC) environments have been lagging in that process, as there’s still much work to figure out how to apply containerization platforms for HPC in real-life scenarios. Kubernetes and OpenShift have many advantages – generally speaking, container technologies use quite a bit less overhead from the computing perspective while providing many benefits in flexibility, modularity, and maintenance. Therefore, they are ideal for tasks requiring a lot of computing power. There are also some tradeoffs regarding the complexity of these two platforms - they’re just not that user-friendly when used by people without years of experience managing them. In this paper, we propose a different architecture based on seamless hardware integration and user-friendly, dynamic workload placement based on real-time performance analysis and prediction coupled with Machine Learning-based scheduling.

Carbon Capture and Storage (CCS) stands as a pivotal technological stride toward a sustainable future, with the practice of injecting supercritical CO2 into subsurface formations having already been an established practice for enhanced oil recovery operations. The overarching objective of CCS is to protract the operational viability and sustainability of platforms and oilfields, thereby facilitating a seamless transition towards sustainable practices. This study introduces a comprehensive framework for optimizing well placements in CCS operations, employing a derivative-free method known as Bayesian optimization. The development plan is tailored for scenarios featuring aquifers devoid of flow boundaries, incorporating production wells tasked with controlling pressure buildup and injection wells dedicated to CO2 sequestration. Notably, the wells operate under group control, signifying predefined injection and production targets and constraints that must be adhered to throughout the project’s lifespan. As a result, the objective function remains invariant under specific permutations of the well locations. Our investigation delves into the efficacy of Bayesian optimization under the introduced permutation invariance. The results reveal that it demonstrates critical efficiency in handling the optimization task extremely fast. In essence, this study advocates for the efficacy of Bayesian optimization in the context of optimizing well placements for CCS operations, emphasizing its potential as a preferred methodology for enhancing sustainability in the energy sector.

The aim of this study was to evaluate the effect of two different insertion speeds at 8 different insertion torque values ranging from 25-60 during implantation in a dense polyurethane D1 bone model on the placement status and removal torque of dental implants. In this study, 50 pcf single layer polyurethane plates were used. In the study, a total of 320 implant sockets were divided into 2 groups as Group 1 (30 rpm) and Group 2 (50 rpm) in terms of insertion speed. Group 1 and Group 2 were divided into 8 subgroups as 25, 30, 35, 40, 45, 50, 55 and 60 torques. There were 20 implant sockets in each subgroup. During the implantations, implant placement status and removal torque values were assessed. There was a statistically significant difference between the 30 and 50 RPM groups in terms of overall implant placement status (p<0.01). It was found that the removal torque values at 50 RPM were statistically significantly higher than those at 30 RPM (p<0.01). This study showed that in dense D1 bone, the minimum parameters at which all implants could be placed at bone level were 50 torque at 30 rpm and 40 torque at 50 rpm.

Poultry farming in Slovakia has a tradition and an irreplaceable position to ensure rational nutrition for the population. In terms of a nutritional value, poultrymeat (Galliformes) contains a high amount of proteins, essential amino acids, essential unsaturated fatty acids, minerals, vitamins and a low fat content. Poultrymeat production has a relatively short reproductive cycle and thus allows regulating the demand and supply. The poultry market also influences the development of domestic consumption. According to the Statistical Office of the Slovak Republic, the consumption of meat has witnessed a persistent increase over the last 10 years. [1] According to the 2023 AVEC (The Voice of European Meat Sector) annual report, the consumption of poultrymeat in Slovakia was 20.0 kg per person per year. The average consumption in the EU-27 (2021) was 23.4 kg, with the countries with the highest consumption being Portugal (37.8 kg), Ireland (36.0 kg), Hungary (33.5 kg) and Spain (29.9 kg). On the other hand, the countries with the lowest consumption of poultrymeat, apart from Slovakia, also include Austria and Greece with a consumption of 21.5, resp. 21.0 kg [2]. The breeding of broiler chickens, as well as the production and placing on the market of poultrymeat must comply with the requirements laid down by legislation, while the compliance is regularly checked by the competent authorities.

Sharing confidential information is a critical concern in today’s world. Secret sharing schemes facilitate the sharing of secrets in a way that ensures only authorized participants (shareholders) can access the secret using their allocated shares. Hierarchical secret sharing schemes (HSSSs) build upon Shamir’s scheme by organizing participants into different levels based on priority. Within HSSS, participants at each level can reconstruct the secret if a specified number, denoted as the threshold value (t), or more of them are present. Each level has a predetermined threshold value. If the number of participants falls below the threshold at any level, higher-level participants must be involved in reconstructing the secret at lower levels. Our paper proposes schemes that implement hierarchical access structures and enable the sharing of multiple secrets. Additionally, our proposed scheme includes share verification. We have analyzed potential attacks and demonstrated the scheme’s resistance against them. Through security analysis and comparison with existing schemes, we highlight the novelty and superiority of our proposed approach, contributing to advancements in secure information sharing practices.

Artificial intelligence (AI) is increasingly being used to improve the quality control of point-of-care diagnostics. This is caused by a number of factors, including the following: 1. AI can accelerate and improve testing accuracy. In comparison to humans, AI technology can review data more quickly and precisely, reducing errors and improving overall quality assurance. 2. When it comes to improving POC test findings on healthcare issues such as infectious diseases or medical crises such as heart attacks, AI can be used for sophisticated predictive analytics and modeling that aid in better decision-making. 3. Artificial intelligence facilitates process automation, increasing productivity and lowering labor costs in labor-intensive tasks such as testing and analyzing samples collected at point-of-care facilities. 4. The use of AI enables organizations implementing these solutions to gain insights from large volumes of raw diagnostic data generated faster and more accurately, allowing them to build solid frameworks around preventive care initiatives and significantly influence public health outcomes.5. Artificial intelligence (AI) has been demonstrated to be a useful tool for real-time monitoring systems that identify any problems with test results early so that they can be corrected before affected patients receive inaccurate diagnoses or treatment plans based on false information provided by diagnostic tests performed at points of care such as clinics or hospitals.Using these technologies would allow healthcare organizations to spend less on labor while still receiving exact diagnoses and rapid treatment delivery at a fraction of the cost that manual approaches required earlier.

The research of object classification and part segmentation is a hot topic in computer vision. A considerable number of studies have been carried out about deep learning on 3D point clouds. However,it is challenging to achieve effective feature learning due to sparsity of point clouds. Recently, a variety of Transformers have been adopted to improve point cloud processing and display great potential. Nevertheless, large numbers of Transformer layers tend to incur huge computational and memory costs. PointNet++ is one of the most influential neural architectures for point cloud understanding. Although the accuracy of PointNet++ has been largely surpassed by recent networks, this does not mean that PointNet++ has no potential.Thus, this paper offer two major contributions that significantly improve PointNet++ performance. Firstly, we introduce a novel contextual feature extraction (CFE) block that significantly enhances the feature extraction capabilities of PointNet++ networks. Secondly, to further enhance feature fusion, we seamlessly integrate a mutual learning (ML) block into the network architecture. By embedding these two innovative blocks within each layer of the network, we not only enrich the network's functionality but also impart it with greater robustness and adaptability. The specific experiments were conducted on the S3DIS (6-fold cross-validation) and Modelnet40 datasets with 86.5% and 92.7% accuracy, respectively, which proved that our model is comparable or even better than most existing methods for classification and segmentation tasks.

Access to medicines is one of the essential problems in Public Health of low- and middle-income countries (LMICs). The World Health Organization (WHO) defines access to medicines as the possibility of "having continuously accessible and affordable medicines in public or private health facilities that are within a kilometer of the place of residence." Access to medicines, as defined by the WHO, is not fully guaranteed in many LMICs and even in many regions of high-resource countries. The WHO identifies several factors as determinants of limitations in the access to medicines: rational selection, affordable prices, sustainable financing, and reliable health services. The action on these factors makes it possible to improve universal access to medicines with consequent improvement in Public Health. Adequate access to antibiotics and vaccination will avoid a large part of the deaths caused by infectious diseases in the LMICs. However, the emergence of resistance and the difficulties in vaccination campaigns due to socio-political or cultural problems make it challenging to fight many easily treatable infectious diseases. The use and abuse of antibiotics are inevitably associated with the appearance of resistances that make them ineffective. Thus, whereas limited access to antibiotics raises mortality rates from infectious diseases, generalized open access to them ends up eliminating their clinical value. Moreover, the contraction of research in this field for many years has reduced the success in discovering new drugs. Additionally, local market regulations, inadequate selection, inaccessible prices, especially for those of second and third-generation, inefficient health systems, and difficulties of administration and control of prescription compliance, especially in the case of combined therapies, are additional obstacles to universal access to antibiotics. In order to simultaneously improve access to antibiotics and keep resistances under control, it is necessary to develop training and education activities at different social levels (from patients to various Health Care Providers) to complement the national or supranational strategic plans.

Background and Objectives: Cancer as the second leading cause of death in the United States poses a huge healthcare burden. Barriers to access to advanced therapies influence the outcome of cancer treatment. In this study, we examined whether insurance types affect the quality of cancer clinical care regarding access to an important monoclonal antibody, ramucirumab. Materials and Methods: Data for 13,340 cancer patients with Purchased or Medicaid insurance from the All of Us Database were collected for this study. The Chi-square test of proportions was employed to determine the significance of patient cohort characteristics and ramucirumab usage between Purchased and Medicaid insurance groups. The independent t-test was utilized to assess the influences of other determinants on insurance types. Results: Cancer patients who are African American, with lower socioeconomic status, or with lower educational attainment are more likely to be insured by Medicaid. Analysis of survey questions demonstrated the relationship between income and education level with insurance type as Medicaid cancer patients were less likely to receive primary care and specialist physician access and more likely to request lower cost medications. In addition, those with Medicaid insurance were identified to have poorer access to expensive therapeutics like ramucirumab compared to those with Purchased insurance.  Conclusions: The inequities of the US healthcare system are observed for cancer patient care; access to physicians and therapeutics are highly varied and dependent on insurance types. Socioeconomic status determines insurance type, which unfortunately generates a significant impact on cancer treatment and disease outcome.

In recent years supply chains have evolved into huge ecosystems, demanding trust, provenance, and data privacy. Since blockchain technology (BCT) allows for the development of a distributed environment, it is ideal for supply chain management (SCM) applications. However, concerns regarding data privacy have impeded the development of blockchains. Despite the fact that some blockchains can restrict participants to read and write data, the blockchain’s transparency makes protecting sensitive data challenging. To solve the data privacy challenge, this paper proposes a framework, AccessChain, that is an SCM access control framework based on an attribute-based access control (ABAC) model that restricts access to competing parties while allowing for network scalability. This proposed AccessChain model has two types of ledgers in the system: local and global. Local ledgers are used to store business contracts between stakeholders and the ABAC model management, whereas the global ledger is used to record transaction data. AccessChain can enable decentralized, fine-grained and dynamic access control management in SCM when combined with the ABAC model and BCT. This paper’s experimental results illustrate that high throughput can be achieved in a large-scale request environment while maintaining data privacy and sustaining a scalable network.

Data4HumanRights training materials have been developed as open-source and tailored to limited resource settings where community data collectors often live and work. An overview of how the training material was developed together with community data collectors in Nigeria and Kenya is provided. The paper gives insights into the fundamental principles (i.e., inclusiveness, adaptive, limited resources, gender- and incentive-sensitive) and the structure of the open-access training materials. This resulted in 28 modules designed to be delivered in a face-to-face format in less than one day by a local trainer. To maximize adaptivity, the training modules can be mixed and matched (e.g., as individual modules or a learning path of several modules around a specific training need). The individual modules cover a range of methods and tools that are useful to human rights work, for example, documenting evictions, performing rapid needs assessments after acute crises, community profiling, and monitoring community development indicators. The training materials contain instructions for the facilitator(s) of the training and all necessary training materials to conduct the training. To maximize inclusivity, the training covers basic to advanced topics. Most training modules address basic training topics that can be optimally followed with a mobile phone (to avoid using a computer and printing handouts). The training was developed and implemented with local community groups in Nigeria and Kenya. The material is free to use, adapt, and translate into different contexts and languages.

Ensuring fire safety is an important condition for the successful operation of industrial enterprises. It is necessary to detect the threat of fire before ignition. An indicator of danger is the appearance of gas, which occurs as a result of unauthorized heating of equipment. Gas sensors make it possible to detect the appearance of gases characteristic of the decomposition of materials at the stage of smouldering and pyrolysis, which cause a change in the composition of the atmosphere. This paper presents a mathematical method for the rational placement of gas analyzers for premises of potentially hazardous industries. It is the rational placement of gas sensors, which ensures safety, taking into account economic feasibility that determines the effectiveness of their use. For the first time, the analysis of gas accumulation during the movement of the flow from the source to the ceil-ing, then propagation to the location of the sensors, is used for the first time to select the placement of gas sensors. Depending on the permissible values of the gas volume, the placement and number of gas sensors are selected. The calculation of the conditions for the rational placement of gas sen-sors for the most common indicators, such as carbon monoxide and hydrogen at different sizes and heights of rooms, is carried out. The method of calculating the location of gas analyzers makes it possible to diagnose and predict fire hazard at technological facilities on the basis of gas control, and compare the obtained values with the maximum permissible values. This method provides cal-culation of the coordinates of the gas source from the coordinates of the triggered sensors. Knowing the coordinates of all sensors, the coordinates of the sensors that gave the alarm, and the formula for determining the volume of the gas cloud under these sensors, it is possible to assess the localization of the source of dangerous gas in the protected room. This increases the efficiency of the fire safety system. The method makes it possible to control the layout of sensors depending on the volume of protected premises, types of production, the creation of new sensors, changes in the composition of hazardous gas in different technological conditions.

For multi-sensor integrated systems, such as a mobile mapping system (MMS), data fusion at sensor-level, i.e., the 2D-3D registration between optical camera and LiDAR, is a prerequisite for higher level fusion and further applications. This paper proposes a line-based registration method for panoramic images and LiDAR point cloud collected by a MMS. We first introduce the system configuration and specification, including the coordinate systems of the MMS, the 3D LiDAR scanners, and the two panoramic camera models. We then establish the line-based transformation model for panoramic camera. Finally, the proposed registration method is evaluated for two types of camera models by visual inspection and quantitative comparison. The results demonstrate that the line-based registration method can significantly improve the alignment of the panoramic image and LiDAR datasets under either the ideal spherical or the rigorous panoramic camera model, though the latter is more reliable.

Minimally invasive approaches to the aortic valve have been described since 1993, with great hopes that they would become universal and facilitate day-case cardiac surgery. The literature has shown that these procedures can be undertaken with equivalent mortality, similar operative time, comparative cost and some benefits in hospital length of stay. The competing efforts of the transcatheter aortic valve implantation for these same outcomes have provided an excellent range of treatment options for patients from the Heart Team. We describe the current state of the art, including technical considerations, caveats and complications of minimal access aortic surgery and predict future directions in this space.

Minimal access cardiac surgery appears to be the future. It is increasingly desired by cardiologists and demanded by patients who perceive superiority. Minimal access coronary artery revascularisation has been increasingly adopted throughout the world. Here we review the history of minimal access coronary revascularization and see that it is almost as old as the history of cardiac surgery. Modern minimal access coronary revascularization takes a variety of forms – namely minimal access direct coronary artery bypass grafting (MIDCAB), hybrid coronary revascularisation (HCR) and totally Endoscopic Coronary Artery Bypass Grafting (TECAB). It is noteworthy that there is significant variation in nomenclature and approaches for minimal access coronary surgery and this truly presents a challenge to comparing the different methods. However, these approaches are increasing in frequency and proponents demonstrate clear advantages for their patients. The challenge that remains, as for all areas of surgery, is demonstrating superiority of these techniques over tried and tested open techniques which is very difficult. There is a paucity of randomized controlled trials to help answer this question, and the future of minimal access coronary revascularisation to some extent is dependent on such trials. Thankfully some are underway and the results eagerly anticipated.

A framework for optimal sensor placement (OSP) for virtual sensing using the modal expansion technique and taking into account uncertainties is presented based on information and utility theory. The OSP maximizes a utility function that quantifies the expected information gained from the data for reducing the uncertainty of quantities of interest (QoI) predicted at the virtual sensing locations. The utility function is extended to make the OSP design robust to uncertainties in structural model and modelling error parameters, resulting in a multidimensional integral of the expected information gain over all possible values of the uncertain parameters and weighted by their assigned probability distributions. Approximate methods are used to compute the multidimensional integral and solve the optimization problem that arises. The Gaussian nature of the response QoI is exploited to derive useful and informative analytical expressions for the utility function. A thorough study of the effect of model, prediction and measurement errors and their uncertainties, as well as the prior uncertainties in the modal coordinates on the selection of the optimal sensor configuration is presented, highlighting the importance of accounting for robustness to errors and other uncertainties.

Modal testing is a common step in aerostructure design, serving to validate the predicted natural frequencies and mode shapes obtained through computational methods. The strategic placement of sensors during testing is crucial to accurately measuring the intended natural frequencies. However, conventional methodologies for sensor placement are often time-consuming and involve iterative processes. This study explores the potential of machine learning techniques to enhance sensor selection methodologies. Three machine learning-based approaches are introduced and assessed, comparing their efficiency with established techniques. The evaluation of these methodologies is conducted using a numerical model of a beam to simulate real-world scenarios. The results offer insights into the efficacy of machine learning in optimizing sensor placement, presenting an innovative perspective on enhancing the efficiency and precision of modal testing procedures in aerostructure design.

This study aims to develop novel automated computer vision algorithms and systems for component replacement inspection for Printed Circuit Boards (PCBs). The proposed algorithms are able to identify locations as well as sizes of different components. They are object detection algorithms based on keypoints of the target components. The algorithms can be implemented as neural networks consisting of two portions: frontend networks and backend networks. The frontend networks are used for the feature extractions of input images. The backend networks are adopted for producing component inspection results. Each component class can has its own frontend and backend networks. In this way, the neural model for the component class can be effectively reused for different PCBs. To reduce the computation time for the inference of the networks, different component classes can share the same frontend networks. A two-stage training process is proposed for effectively exploring features of different components for accurate component inspection. The proposed algorithm has the advantages of the simplicity for training data collection, high accuracy for defect detection, and high reusability and flexibility for online inspection. The algorithm is an effective alternative for the automated inspection in smart factory with growing demand for product quality and diversification.

Over the past four decades, China has experienced a nutritional transition and has developed the largest population of internet users. In this study, we evaluated the impacts of internet access on the nutritional intake in Chinese rural residents. An IV-Probit-based propensity score matching method was used to determine the impact of internet access on nutritional intake. The data were collected from 10042 rural households in six Chinese provinces. The results reveal that rural residents with internet access have significantly higher energy, protein, and fat intake than those without. Chinese rural residents with internet access consumed 1.35% (28.62 kcal), 5.02% (2.61 g), and 4.33% (3.30 g) more energy, protein, and fat, respectively. There was heterogeneity as regards the intake of energy, protein, and fat among those in different income groups. Moreover, non-staple food consumption is the main channel through which internet access affects nutritional intake. The results demonstrate that the local population should use the internet to improve their nutritional status. Further studies are required to investigate the impact of internet use on food consumed away from home and micronutrients intake.

We present a set of software packages that provide uniform access to diverse biological vocabulary resources that are instrumental for current biocuration efforts and tools. The Unified Biological Dictionaries (UniBioDicts or UBDs) provide a single query-interface for accessing the online API services of leading biological data providers. Given a search string, UBDs return a list of matching term, identifier and metadata units from databases (e.g. UniProt), controlled vocabularies (e.g. PSI-MI), and ontologies (e.g. GO, via BioPortal). This can be coupled to for instance the ‘vsm-autocomplete’ module: an input field (user-interface component) that offers autocomplete lookup for these dictionaries. UBDs create a unified gateway for accessing life science concepts, helping curators find annotation terms across resources (based on descriptive metadata and unambiguous identifiers), and data users search and retrieve the right query terms.

The extent of access to energy of displaced populations in settlements and camps in Africa is largely 14 unknown. A multitude of contextual factors, such as the location and the characteristics of housing, 15 the legal status, the socio-cultural background, and the availability of humanitarian and public ser- 16 vices impact the living conditions and the needed energy services. Limitations in accessing energy 17 services have direct, multilayered, and far-reaching implications, including impacts on health, nu- 18 trition, education, protection, and livelihood. The objective of this article is to contribute to a more 19 comprehensive overview of the current state of energy access in displacement contexts on the Afri- 20 can continent by identifying and utilizing existing data. After a screening of the vast and various 21 available information, setting up of a database, consolidating the gathered data as well as assessing 22 the quality through a quality assessment method, the currently available information is visualized 23 and discussed. Considerable differences in the access to electricity for displaced persons across the 24 countries are found. For both electricity and clean cooking, the availability for displaced persons 25 ranges from nearly no access at all up to an access rate of 100%. More strikingly, the results also 26 show that besides South Africa and countries in the Maghreb region, the access to both clean cook- 27 ing and electricity for displaced persons is very low. At the same time, the fragmented data availa- 28 bility, the poor data quality, and the questionable expediency of available data allows neither solid 29 theoretical conclusions nor planning of effective practical implementation measures. Novel inter- 30 disciplinary research, conceptual frameworks and indicators are needed for the purpose of compa- 31 rability and consistency. Future research has the potential to more comprehensively capture the 32 current state of access to energy in displacements contexts and in a next step to examine how energy 33 is interwoven in the lives of displaced people to derive a set of more detailed context-sensitive en- 34 ergy indicators. It is essential that the concerned persons, the displaced persons themselves are in- 35 cluded in the research in a meaningful way.

Accurate classification of objects in 3D point clouds is a significant problem in several applications, such as autonomous navigation and augmented/virtual reality scenarios, which has become a research hot spot. In this paper, we presented a deep learning strategy for 3D object classification in augmented reality. The proposed approach is a combination of the GRU and LSTM. LSTM networks learn longer dependencies well, but due to the number of gates, it takes longer to train; on the other hand, GRU networks have a weaker performance than LSTM, but their training speed is much higher than GRU, which is The speed is due to its fewer gates. The proposed approach used the combination of speed and accuracy of these two networks. The proposed approach achieved an accuracy of 0.99 in the 4,499,0641 points dataset, which includes eight classes (unlabeled, man-made terrain, natural terrain, high vegetation, low vegetation, buildings, hardscape, scanning artifacts, cars). Meanwhile, the traditional machine learning approaches could achieve a maximum accuracy of 0.9489 in the best case.

Visual Sensor Networks (VSNs) have been the focus of numerous studies, emphasizing the quality of the information they generate. The primary goal of these networks is to capture data from an area, extract the pertinent information from the visual scene, and facilitate communication. However, the presence of objects in the study area can impacted the network's efficiency, linking the quality of acquired data directly to the positioning of the cameras. Strategically positioning multiple cameras in a potentially complex area, while ensuring effective communication between nodes, presents a challenging issue in VSNs applications. This paper introduces a specific method to enhance the deployment of visual sensors in indoor environments. The research addresses the theme of multi-objective optimization of VSN deployment, integrating various criteria: maximizing overall visual coverage, maximizing the observation of zones of interest, maximizing observation redundancy of zones of interest and ensuring communication connectivity for data transfers. To tackle this problem, we simulate the observed environment incorporating cameras, obstacles, and considering zones of interest. Camera positioning is performed while considering visual constraints and the scene's characteristics. The quality of positioning is evaluated based on the defined objective functions. Initially, a comparative study is conducted with a state-of-the-art approach, integrating the first three objective functions. Subsequently, we incorporate the fourth objective function to ensure data transfers. The proposed method demonstrates efficient camera network deployments in indoor areas, considering global coverage and observation redundancy. In contrast to the state-of-the-art, these results are achieved in areas with visual obstacles while ensuring communication connectivity between the different cameras.

The wave energy converter (WEC) technology constantly develops new designs and models. To encourage its development within the energy sector, research is required to improve current designs and create durable and effective devices. However, it is also crucial to investigate the suitability of a WEC to a site-specific sea condition as this can impact its optimal power absorption and constructability. This study evaluates and compares the efficiency of a heaving buoy with varied geometries in one of the most energetic places along the Mexican coast. A statistical analysis of the wave climate on the coast of Ensenada during the last 42 years is performed to define the conditions to which the device is subjected. The location of the WEC in shallow waters is chosen using a computational model which solves the modified mild slope equation in its elliptic shape. The heaving buoy floater is studied using three distinct geometries: a semi-sphere, a cylinder, and a proposed rounded semi-rectangle. The hydrodynamic response of the three geometries is then analysed in the frequency and time domain using ANSYS AQWA. The hydrodynamic study involves the assessment of the floating body dynamics, exerted forces, the power absorbed as well as the suitability of the proposed power take-off (PTO) system. Findings reveal that the proposed geometry absorbs the most energy, with an annual power of 135.11 MW, and that the transmission PTO design is appropriate for this type of technology.

The point cloud is a form of three-dimensional data that comprises various detailed features at multiple scales. Due to this characteristic and its irregularity, point cloud analysis based on deep learning is challenging. While previous works utilize the sampling-grouping operation of PointNet++ for feature description and then explore geometry by means of sophisticated feature extractors or deep networks, such operations fail to describe multi-scale features effectively. Additionally, these techniques have led to performance saturation. And it is difficult for standard MLPs to directly "mine" point cloud. To address above problems, we propose the Detail Activation (DA) module, which encodes data based on Fourier transform after sampling and grouping. We activate the channels at different frequency levels from low to high in the DA module to gradually recover finer point cloud details. As training progresses, the proposed Point-MDA can uncover local and global geometries of point cloud progressively. Our experiments show that Point-MDA achieves superior classification accuracy, outperforming PointNet++ by 3.3% and 7.9% in terms of overall accuracy on the ModelNet40 and ScanObjectNN dataset, respectively. Furthermore, it accomplishes this without employing complicated operations, while exploring the full potential of PointNet++.

A software defined radio (SDR) is a communication system that makes use of components that can be configured through software, in contrast to traditional systems where these components are variable through hardware, these radio devices are much more versatile, this article describes the factors that must be considered when implementing a communication system based on Software Defined Radios (SDR), in order to reduce the attenuation factors and thus obtain the maximum distance for a transmission of data effectively in the UHF band. The calculations made for the first Fresnel zone and for the design of the Ground Plane type antennas used in the transmission/reception stages of the x40 bladeRF platforms are also presented. The tests were carried out at the facilities of the Huarangal Nuclear Center of the Peruvian Institute of Nuclear Energy, obtaining favorable results that allow ratifying the versatility and performance of the SDRs.

Background: While it is established that intravenous catheter placement duration is strongly linked to the risk of catheter colonization and bloodstream infections, there are still substantial knowledge gaps concerning the varying durations of PICC placement that lead to either infection or colonization by common pathogens, particularly MDR pathogens. The present study aims to compare the dwell time required for MDR pathogens to colonize with the time required to cause Central Line-Associated Bloodstream Infections (CLABSIs) in critically ill patients with PICCs and compares it with non-MDR pathogens, shedding light on the significance of preventive procedures to control MDR infections in clinical settings. Methods: Data from critically ill patients with PICCs admitted consecutively to «Metropolitan» Hospital in Athens, Greece, from May 2017 to May 2020 were retrospectively analysed. Results: In this study, 86 hospitalized patients, consisting of 56 (65.1%) males and 30 (34.9%) females, with a mean age of 55.67±21.1 years (range 16-91 years), presented with both CLABSIs and colonization following PICC placements. Specifically, 42 (48.8%) of them presented with CLABSIs, while 44 (51.2%) presented with colonization. Among the total participants, an MDR pathogen was isolated from 26 (30.2%) PICCs, while other pathogens were isolated from 60 (69.8%). The mean duration of catheter dwell time for all participants was 20.94±14.22 days (range 3-72 days). When analysed separately for each group, the dwell time for PICCs with CLABSIs was 25.73±16.19 days and 16.36±10.28 days for those with colonization (T test, p=0.002). Additionally, the mean dwell time for PICCs infected by non-MDROs was 22.48±15.64 days whereas for PICCs with MDROs, it was 17.38±9.5 days (T test, p=0.005). In PICCs with CLABSIs, the mean indwelling time for MDR pathogens was 21.50±12.31 days, while for non-MDROs, it was 27.73±16.98 days (T test, p=0.417). In PICCs with colonization, the mean dwell time for MDR pathogens was 15.55±7.73 days, while for non-MDROs, it was 16.92±11.85 days (T test, p=0.124). Among PICCs with MDR pathogens (n=26), the mean duration in CLABSIs events (n=18) was 21.5±12.31 days and in colonization events 15.55±7.73 days, (n=8) (T test, p=0.146). Conclusions: The present study reveals that colonization of PICCs exhibited a shorter dwell time compared to those with CLABSIs. Moreover, PICCs infected by MDROs had a shorter mean dwell time than those with non-MDROs. These findings underscore the importance of considering infection status and microbial resistance patterns when evaluating PICC dwell times.

The WTO is here to stay. Institutions are never perfect. The way the WTO, as an institution, runs its business may not be perfect either. Arab countries are attempting to broaden their engagement in the multilateral trading system in a manner that has many implications. This engagement includes accession to the WTO, participation in WTO dispute resolution mechanism, and representations at the WTO.

This paper proposes a novel single-stage buck-boost three-Level neutral-point-clamped (NPC) inverter with two independent dc sources coupled for the grid-tied photovoltaic (PV) application, which can effectively solve the unbalanced operational conditions generally appeared between two coupled independent PV sources induced by the unequal irradiation and temperature distribution. The proposed control scheme can simultaneously guarantee the maximum power point (MPP) operation of both PV sources and maintain the output waveform quality. Compared to the traditional two-stage PV inverter, the proposed NPC inverter could reduce the PV array voltage requirement and dc-link capacitors’ voltage rating, meanwhile show the advantage in operational efficiency. MATLAB simulations and the captured experimental results are presented to show the performance of the proposed three-level inverter.

_{Superconducting foams of YBa$_2$Cu$_3$O$_y$ (YBCO) are proposed as trapped field magnets or supermagnets. The foams with an open-porous structure are light-weight, mechanically strong and can be prepared in large sample sizes. The trapped field distributions were measured using a scanning Hall probe on various sides of an YBCO foam sample after field-cooling in a magnetic field of 0.5 T produced by a square Nd-Fe-B permanent magnet. The maximum trapped field (TF) measured is about 400 G (77 K) at the bottom of the sample. Several details of the TF distribution, the current flow and possible applicatons of such superconducting foam samples in space applications, e.g., as active elements in flux-pinning docking interfaces (FPDI) or as portable strong magnets to collect debris in space, are outlined.}

Interactions between mobile robots and human operators in common areas require a high safety especially in terms of trajectory planning, obstacle avoidance and mutual cooperation. In this connection the crossings of planned trajectories, their uncertainty based on model fluctuations, system noise and sensor noise,play an outstanding role. This paper discusses the calculation of expected areas of interactions du ring human-robot navigation with respect to fuzzy and noisy information. Expected crossing points of possible trajectories are nonlinearily associated with positions and orientations of robot and human. The nonlinear transformation of a noisy system input, such as directions of motion of human and robot, to a system output, the expected area of intersection of their trajectories, is done by two methods: statistical linearization and the sigma-point-transformation. For both approaches fuzzy approximations are presented and the inverse problem is discussed where the input distribution parameters are computed from given output distribution parameters.

Edge computing reduces the response time of real-time services with handling dynamic traffics reliably. Edge servers with limited resources utilize container technology that provides a lightweight execution environment. When deploying containers in edge servers, a container image is required and is downloaded from a remote registry. Therefore, these operations are dependent on network overhead between the container deployment system and the remote registry. Through motivation experiments, we show that container pooling time increases in proportion to physical distance and has characteristics that vary flexibly depending on runtime time. In this study, we define a system model for high-speed registry deployment in this edge system and propose a clustering technique into k groups based on the network overhead and affinity of the regionally distributed edge servers that make up the edge system. Also, considering idle resources, we propose a technique to deploy a registry after electing a leader for each cluster. A simulation experiment is conducted to verify the performance of the proposed technique and shows that performance improvement can be achieved regardless of the number of edge servers and the k value.

INTRODUCTION: Achalasia is a pathology with an incidence of 1 in 100,000 inhabitants per year. There are very limited data on achalasia in the obese population, especially in those undergoing bariatric surgery. The approach of choice for cases of achalasia is fundoplication to correct the reflux; however, lacking a fundus due to a previous gastrectomy, an alternative that offers optimal results should be chosen. Here we present the surgical approach in a case of esophageal achalasia and a history of vertical sleeve gastrectomy, where we performed simultaneous Heller's cardiomyotomy and laparoscopic Roux-en-Y gastric bypass, as well as the results obtained. CASE PRESENTATION: 44-year-old woman with no chronic degenerative diseases, with a previous record of vertical sleeve gastrectomy 5 years ago, who started 1 year and 5 months earlier with dysphagia to liquids, then to solids, in addition to weight loss of 10 kilograms in 4 months. The BMI before vertical sleeve gastrectomy was 32 kg/m2, her BMI at the time of admission was 20 kg/m2; she also presented regurgitation and generalized weakness. After analyzing the surgical options, it was decided to perform a Heller cardiomyotomy and a Roux-en-Y gastric bypass. DISCUSSION AND CONCLUSIONS: The procedure turned out to be safe and successful in treating achalasia symptomatology, in addition to complete resolution of the reflux symptom.

In this paper, we investigated transducer placement strategies for detecting crack in primary aircraft structures using ultrasonic Structural Health Monitoring (SHM). The approach developed is for an expected damage location based on fracture mechanics, for example fatigue crack growth in a high stress location. To assess the performance of the developed approach, finite-element (FE) modelling of a damage tolerant aluminum fuselage has been performed by introducing an artificial crack at a rivet hole into the structural FE model and assessing its influence on the Lamb wave propagation, compared to a baseline measurement simulation. The efficient practical sensor position was determined from the largest change in area that is covered by reflected and missing wave scatter using an additive color model. Blob detection algorithms were employed in order to determine the boundaries of this area and to calculate the blob centroid. To demonstrate that the technique can be generalized, the results from different crack lengths and from tilted crack are also presented.

One of the rapidly developing research areas in the power system is the integration of distributed generation (DG) with the distribution system. The size and location of DG sources had a considerable impact on power system networks. Artificial intelligence (AI) techniques can be used to address multidimensional problems relating to DG size and location in distribution systems. Heuristic optimization offers a reliable and effective method for solving complicated real-world problems. This work focuses on a hybrid approach that combines the two heuristic optimization methods i.e., Particle Swarm Optimization (PSO) and Genetic Algorithm (GA) for the optimal siting and sizing of DG in distribution systems. This hybrid approach combines ideas from GA and PSO and generates individuals in a new generation using both PSO mechanisms and the procedures found in GA. An extensive performance analysis of the IEEE 14 busbar standard test system is conducted to demonstrate the viability of the suggested methodologies. In the designated locations, DG is placed, and the outcomes have been verified. The results indicated that the right placement of DG injection enhances the voltage profile and lowers the distributed system’s power losses. These techniques offer unique methods for determining the location of the DG unit, demonstrating the potential of such a computational techniques to reduce computing time and complexity while simultaneously reducing human errors associated with hit-and-trail methods.

Vehicle windshield wiper system increases the driving safety by contributing a clear shot viewing to the driver. In this paper, modelling, designing and simulation of a vehicle windshield wiper system with robust control theory is done successfully. H∞ loop shaping and robust pole placement controllers are used to improve the wiping speed by tracking a reference speed signals. The reference speed signals used in this paper are step and sine wave signals. Comparison of the H∞ loop shaping and robust pole placement controllers based on the two reference signals is done and convincing results have been obtained. Finally the comparative results prove the effectiveness of the proposed H∞ Loop Shaping controller to improve the wiping mechanism for the given two reference signals.

Access and Benefit Sharing (ABS) is a framework which refers to a relatively recent type of legal requirements for access to and/or use of “genetic resources”. They are based on diverse national and regional laws and regulations, which mostly result from the implementation of the United Nations’ Convention on Biological Diversity (CBD) and its supplementary agreement, the Nagoya Protocol. Their ambition is to achieve fair and equitable sharing of benefits arising out of the use of genetic resources as an incentive to conserve and sustainably use them. This paper describes the experiences, practical constraints and complexities encountered by users of genetic resources when dealing with ABS legislation, with a focus on users from the private sector. We provide insights on how ABS laws have fundamentally changed the way of working with genetic resources in the hope that it inspires re-thinking of the ABS framework, to better support the overall objectives of the CBD.

This paper details the evolution of access network sharing models from legacy DSL to the most recent fibre-based technology and the main challenges faced from a technical and business perspectives. We first give an overview of existing access sharing models, that span physical local loop unbundling and virtual unbundled local access. We then describe different types of optical access technologies and highlight how they support network sharing. Next, we examine how the concept of SDN and network virtualization has been pivotal in enabling the idea of “true multi-tenancy”, through the use of programmability, flexible architecture and resource isolation. We give examples of recent developments of cloud central office and OLT virtualization. Finally, we provide an insight into the role that novel business models, such as blockchain and smart contract technology, could play in 5G networks. We discuss how these might evolve, to provide flexibility and dynamic operations that are needed in the data and control planes.

Sparse recovery of fluid flows using data-driven proper orthogonal decomposition (POD) basis is systematically explored in this work. Fluid flows are manifestations of nonlinear multiscale PDE dynamical systems with inherent scale separation that impact the system dimensionality. Given that sparse reconstruction is inherently an ill-posed problem, the most successful approaches require the knowledge of the underlying basis space spanning the manifold in which the system resides. In this study, we employ an approach that learns basis from singular value decomposition (SVD) of training data to reconstruct sparsely sensed information. This results in a set of four control parameters for sparse recovery, namely, the choice of basis, system dimension required for sufficiently accurate reconstruction, sensor budget and their placement. The choice of control parameters implicitly determines the choice of algorithm as either $l_2$ minimization reconstruction or sparsity promoting $l_1$ norm minimization reconstruction. In this work, we systematically explore the implications of these control parameters on reconstruction accuracy so that practical recommendations can be identified. We observe that greedy-smart sensor placement provides the best balance of computational complexity and robust reconstruction for marginally oversampled cases which happens to be the most challenging regime in the explored parameter design space.

Dental caries is a public health problem worldwide according to WHO data. Among treatments in pediatric dentistry, prefabricated metal crowns (PMCs) have been one of the most successful options since they were introduced in cases of considerable tooth destruction. Our objective was to detect the presence and concentration of iron (Fe), chromium (Cr), and nickel (Ni) in saliva of patients who require rehabilitation with PMCs, before and after their placement. A quasi-experimental study was performed in 32 patients who attended dental care in a pediatric dentistry clinic at a public university and who required rehabilitation with PMCs. Parametric tests (ANOVA and Pearson correlation) were performed, and a p ≤ 0.05 was considered statistically significant. Statistically significant differences were found when comparing the Ni release before, 1 week, and 1 month after placing the crowns. Similarly, we observed a positive correlation between the number of crowns and Ni release. No tests were performed for Fe and Cr because the amounts of these metals were less than 0.1 ppb, which was not detectable by inductively coupled plasma optical emission spectrometry (ICP-OES). The levels of Fe, Cr, and Ni released were below toxic health levels. Studies are required to evaluate whether this release has negative effects at cellular levels.

Much of the debate on Plan S seems to concentrate on how to make toll access journals open access, taking for granted that existing open access journals are Plan S compliant. We suspected this was not so, and set out to explore this using DOAJ's journal metadata. We conclude that an overwhelmingly large majority of open access journals are not Plan S compliant, and that it is small HSS publishers not charging APCs that are least compliant and will face major challenges with becoming compliant. Plan S need to give special considerations to smaller publishers and/or non-APC-based journals.

Preprints is a multidisciplinary preprint platform that makes scientific manuscripts from all fields of research immediately available at www.preprints.org. Preprints is a free (not-for-profit) open access service supported by MDPI in Basel, Switzerland.

A healthy 47-year-old woman consulted the Oral Surgery and Implantology Unit of the University Hospitals of Geneva with a request to treat her painful tooth 11 and replace the missing tooth 21. The dental history revealed that the patient had lost teeth 21 and 22 due to advanced caries. On clinical examination, tooth 11 showed an ill-fitting prosthetic crown with overhanging margins, an increased localized probing depth of 8 mm in the disto-vestibular area and sensitivity to percussion. The edentulous site 21 showed horizontal bone atrophy. Radiological examination revealed a well-defined unilocular radiotransparent lesion surrounded by a thin radiolucent border, located at the apex of tooth 11 and measuring 10 x 8 mm. The treatment consisted of extraction of 11, enucleation of the apical lesion, insertion of implants at sites 11 and 21 with simultaneous bone augmentation in a single surgical procedure with aesthetic and functional results at 3-year follow-up without any complications. Our case highlights that immediate implant placement in case of cystic periapical lesion represents a good valid alternative to standard treatment.

Agricultural drainage canals that connect upstream fish spawning areas to downstream rivers and lakes serve as crucial habitats for migrating fish. However, disconnections, such as drops and chutes, have been constructed in these canals due to agricultural modernization and flood control measures, hindering the movement of fish with limited swimming abilities. Portable fishways offer a promising solution to reconnect water bodies in agricultural canals, as they can be easily removed during high water discharges to avoid impeding the canals' drainage function. In addition to experimental assessments of fishway functionality, employing a hydrodynamic model to explore effective placement strategies for portable fishways is essential to maximize their effectiveness. This study presents a method to determine the best horizontal location of a portable fishway in an agricultural drainage canal using two-dimensional hydrodynamic simulations within the specified cases. The applicability of this method is demonstrated by addressing the positioning challenge of a portable fishway on a chute in an agricultural drainage canal in Japan. Results indicate that the proposed method allows for the selection of a suitable location, considering preferable hydraulic conditions both within the portable fishway and around its entrance.

Due to the rapid growth of the Internet of Things (IoT), securing communications between a huge number of devices has become very difficult. Access controls and authentication secure the connection between IoT devices and protect sensitive data from unauthorized users or malicious attackers. In this paper, we provide a comprehensive review to emphasize the critical role of authentication and access control in securing IoT environments. This paper explores different types of access controls, like Attribute-Based Access Control and Role-Based Access Control. Furthermore, it demonstrates different authentication techniques, like passwords and biometrics. Based on the previous mechanisms, we discuss different IoT security challenges regarding authentication and access control mechanisms and highlight future directions. In addition, this paper investigates the integration between access control and authentication to safeguard IoT communications.

River monitoring has the potential to grow substantially with present-day available affordable and locally sourced hardware. Yet river monitoring networks are still under pressure due to lack of resources, difficulties with maintenance, and rapidly changing conditions which in part may be due to climate change. We advocate that to turn around this trend, monitoring stations must rely on local people, work with locally available devices, work without contact with water and operate through openly available knowledge. River observations with camera videos have this potential. IP cameras, drones or smartphones are widely available as observation platforms. The scientific methods are well established in literature. Yet current attempts to establish scalable open-source software solutions that can be operated anywhere are lacking. In fact, currently available software is either research-oriented, more aimed at incidental observations, is restricted to single-use licenses, entirely proprietary, or restricted to operations through a third-party Software as a Service. To overcome this obstacle, we present OpenRiverCam, a free and open-source software ecosystem for river observations that can fulfill a wide variety of use cases and business cases through a well-documented and simple to use Application Programming Interface, service workflows, cloud scalability and interoperability, and options to extend to several applications within the hydrological, hydrodynamic, environmental and geospatial domains. We demonstrate its current technical abilities through three different case studies that all originate from a user perspective. We discuss the future developments to meet further requirements, which include documentation, widely available training materials and embedding in curricula, and further hardware and software developments.

Facing unprecedented global declines in the extent and integrity of ecosystems, the 15^th UN Biodiversity Conference (COP-15) in Kunming, China, presents an opportunity for transformative change. However, a lack of consensus on two key issues – resource mobilization and Access and Benefit Sharing (ABS) associated with Digital Sequence Information (DSI) – risks stalling negotiations for an ambitious ‘Post-2020 Global Biodiversity Framework’ as the next 10-year strategic plan under the Convention on Biological Diversity. We highlight systemic misconceptions concerning the financing of biodiversity and the burden this places on the ABS system. In the context of DSI, we caution that conflating ABS with resource mobilization risks disrupting modern science policy built on open access, with potentially severe ramifications for scientific research and innovation. To resolve these tensions, we call for a recalibration of discussions on ABS in order to maximize the value delivered by biodiversity for all of society, including indigenous peoples and local communities.

This paper describes some of the challenges that need to be addressed in order to develop collaborative spectrum sharing systems. The importance of these challenges stems from the assumption that rules for spectrum sharing can change after the deployment of radio networks and the whole system must be able to adapt to them. To address such a requirement, we used a policy-based approach in which transmissions are controlled by a policy interpreter system, and the policies can be modified during system operation. Our primary goal was to develop a prototype of such a system. In this paper, we outline the implementation of policy interpretation, automatic generation of transmission opportunities in case a request for transmission is denied by the policy reasoner, and the generation of rendezvous channels for the synchronization of otherwise asynchronously running software defined radios.

Whole-genome sequencing has advanced our understanding of the population structure of the pathogenic species complex Cryptococcus gattii, which has allowed for the phylogenomic specification of previously described major molecular type groupings and novel lineages. Recently, isolates collected in Mexico in the 1960s were determined to be genetically distant from other known molecular types and were classified as VGVI. We sequenced four clinical isolates and one veterinary isolate collected in the southwestern U.S. and Argentina during 2012-2021. Phylogenomic analysis groups these genomes with those of the Mexican VGVI isolates, expanding VGVI into a clade and establishing this molecular type as a clinically important population. These findings also potentially expand the known Cryptococcus ecological range with a previously unrecognized endemic area.

We investigate the impact of aging on exchangeable inter-arrival times in mixed renewal processes, exploring its implications for reliability and survival analysis. In this study, first, we revisit the definition of renewal point processes, where inter-event time intervals are considered as exchangeable non-negative random variables. Then, we define the concept of statistical aging as latency in the observational process of event counting. Latency affects event detection but preserves exchangeability. However, it may alter the statistical properties of inter-event time intervals. Our analytical and numerical assessments highlight the significance of aging in exchangeable lifetimes, offering insights into key metrics such as the failure survival function, renewal function, and hazard rate function. Through archetypal examples and empirical findings, we illustrate the implications of aging on renewal processes. In particular, employing a Bayesian perspective, we analyze high-frequency currency exchange rate data to assess the impact of aging on volatility risk evaluation. This study contributes novel insights to the literature of renewal theory and survival analysis, emphasizing the role of latency aging in stochastic point processes under exchangeability assumption.

We consider a Cauchy problem for differential equations in a Hilbert space $X$. The problem is stated in a time interval $I$, which can be finite or infinite. Weuse a fixed point argument for history-dependent operators to prove the unique solvability of the problem. Then, we state and prove convergence criteria for both a general fixed point problem and thecorresponding Cauchy problem. These criteria provide necessary and sufficient conditions on a sequence $\{u_n\}$ which guarantee its convergence to the solution of the corresponding problem, in the space of both continuous and continuously differentiable functions. We then specify our results in the study of a particular differential equation governed by two nonlinear operators. Finally, we provide an application in viscoelasticity and give a mechanical interpretation of the corresponding convergence result.

First came the digital banks without offices, and then the “fintech” companies that combined technology and finance to achieve greater efficiency and new business models. Later was the turn of transport and logistics, understood as the sector whose economic activities derived from the transport of people and goods, while on the one hand, it has had a new spring thanks to factors such as online sales. Then, perhaps catalyzed by the pandemic scenario, the turn has reached education, where years ago was only a complement of traditional education, now is a central part with multiple modern methodologies. Numerous studies exist about using or implementing these e-learning procedures, but technical analysis is barely found in references. This work aims to analyze the digital transformation of the main sectors of our society, including finances, transport, and education, together with several examples of how technology was helping to fight the pandemic scenario.

(1) Background: The 2002 Budapest Open Access Initiative recommended on self-archiving of scientific articles in open repositories as the “green road” to open access. Twenty years later, only one part of the researchers deposits their publications in open repositories; moreover, one part of the repositories’ content is not based on self-archived deposits but on mediated nonfaculty contributions. The purpose of the paper is to provide more empirical evidence on this situation and to assess the impact on the future of the green road. (2) Methods: We analyzed the contributions on the French national HAL repository from more than 1,000 laboratories affiliated to the ten most important French research universities, with a focus on 2020, representing 14,023 contributor accounts and 166,939 deposits. (3) Results: We identified seven different types of contributor accounts, including deposits from nonfaculty staff and import flows from other platforms. Mediated nonfaculty contribution accounts for at least 48% of the deposits. We also identified difference between institutions and disciplines. (4) Conclusions: Our empirical results reveal a transformation of open repositories from self-archiving and direct scientific communication towards research information management. Repositories like HAL are somewhere in the middle of the process. The paper describes data quality as the main issue and major challenge of this transformation.

The worldwide interconnected objects, called Internet of Things (IoTs), have been increasingly growing in the last several years. Different social media platforms and devices are continuously generating data about individuals and facilitate the technological and the social convergence of their Internet-based data and services with globalized users. These social and device-related IoTs create rooms for data breaches as such platforms provide ability to collect private and sensitive data. We assert that data breaches are fundamentally failures of access control - most users are too busy or technically ill-equipped to understand access control policy expressions and decisions. We argue that this is symptomatic of globalised societies structured by the conditions of algorithmic modernity; an era in which our data is increasingly interdependent on, and enmeshed with, ever more complex systems and processes that are vulnerable to attack. Ethically managing data breaches is now too complex for current access control systems, such as Role-Based Access Control (RBAC) and Context-Aware Access Control (CAAC). These systems do not provide an explicit mechanism to engage in decision making processes, about who should have access to what data and when, that are involved in data breaches. We argue that a policy ontology will contribute towards the development of Ethical CAAC better suited to attributing accountability for data breaches in the context of algorithmic modernity. We interrogate our proposed Ethical CAAC as a theoretical construct with implications for future policy ontology models and data breach countermeasures. An experimental study on the performance of the proposed framework is carried out with respect to a more generic CAAC framework.

In this paper, a new relay system that uses the UAV as a relay station between the tethered UAV and ground user (TU2U2G) is proposed. The TU2U2G system replaces the base station (BS) in the cellular system with a tethered UAV (TUAV). The TUAV is a UAV that receives power over a cable from a ground control station. It has advantages of high and variable altitude up to (100m) compared to BS. In addition, it overcomes the UAV drawback of the batteries' limited capacity. After that, a 3D placement Algorithm of the UAV as a relay station in the TU2U2G system is proposed. It is presented to maximize the coverage by jointly optimizing the transmitting power and relaying distance. The TU2U2G system shows better results than the traditional cellular system in terms of optimum UAV height, maximum coverage radius, and maximum distance between BS and UAV.

Balanced nitrogen (N) and phosphorus (P) rates coupling with rational fertilization methodology could promote crop N accumulation, N use efficiency and yield production, particularly in semi-arid and arid regions. To test these characteristics, a two-year (2018 and 2019) pot experiment was therefore performed by growing summer maize in a rain-proof glass greenhouse, under 9 combined N (112, 150 and 187 kg ha-1, urea) and P (45, 60, 75 kg ha-1, calcium superphosphate) rates and three contrasting fertilizer placements. The fertilizers were placed by broadcast on soil surface (Broadcast), side band on 4 cm strip soil surface within 7 cm from sowing line (Side band) and deep band on 4 cm strip below 7 cm soil depth within 7 cm from sowing line (Deep band). Results from three maize growth stages (eight-leaf, 45 days after sowing, DAS; tasseling, 60 DAS; and harvest, 115 DAS) showed that leaf, stem, root N accumulation and total soil N were significantly increased under Deep band than under both Side band and Broadcast at N150P60, N187P60, N150P75 and N187P75, but not at N112P45, N150P45, N187P45, N112P60 and N112P75. Significantly greater leaf, stem, and root N accumulations were also displayed at N150 and N187 than at N112 for the same P60 or P75 under Deep band at 60 DAS and 115 DAS, while were for leaf and stem N accumulations at P75 and P60 than at P45 for the same N150 under Deep band at 45 DAS, 60 DAS and 115 DAS. Significantly greater agronomy N use efficiency, partial factor productivity and N use efficiency exhibited under Deep band than under Side band and Broadcast at N150P75 and N187P75, but at N150P60 and N187P60 for NUE only. In addition, leaf, stem, seed, root N concentrations positively correlated with their own N accumulations or soil N concentration at tasseling and harvest stages. Our results demonstrate that a synchronized N150P60, N187P60, N150P75 or N187P75 fertilization rate with Deep band placement can improve soil N availability and root N uptake, and hereby greater aboveground N accumulation, N use efficiency and yield production of maize particularly practical for small-holder farmers globally.

Lymphedema is a chronic and debilitating disease that affects up to 250 million patients worldwide. Recent advances in understanding its pathophysiology, along with improved diagnosis and microsurgical techniques, have enhanced our ability to cope with the challenging task of treating this disease. This review provides an overview of the disease from a surgeon's point of view, including existing imaging modalities used for preoperative assessment, as well as surgical procedures used in its treatment. Advantages and drawbacks of various existing modalities used for pre or intraoperative assessment of lymphatic vessels are discussed. Lymphedema treatment has shifted from palliative debulking procedures (liposuction and direct excision) to those aimed at restoring lymphatic flow and countering the pathophysiology of the disease (lymphaticovenous anastomosis and vascularized lymph node transfer). A combination of both approaches can result in a synergistic benefit for patients and are discussed in this review. Despite recent advances, some controversies persist, and further studies are needed to better define surgical treatment algorithms.

Small and medium-sized enterprises (SMEs) help and support the country in financial and business aspects and employs in the country, overcomes unemployment, and creates job opportunities in different sectors of the country. The study aims to know the entrepreneurial-specific factors like age, gender, education, experience, and skills used as predictors for access to financing of small firms in Khyber Pakhtunkhwa. The questionnaire is used for data collection, and about 204 questionnaires were distributed, of which 192 returned and analyzed through binary logistic regression. The study results reveal that age and level of education have been found significant while gender, experience and skills have insignificant with the access to finance in Khyber Pakhtunkhwa, Pakistan.

Sustainable agriculture is at the forefront of modern farming practices, with a growing emphasis on optimizing crop production while minimizing environmental impact. The choice of fertilizer application technology plays a critical role in achieving these objectives. Soybean (Glycine max (L.) Merr.), a valuable crop globally, serves both as a source of human nutrition and livestock feed. To address the challenges of enhancing soybean production while minimizing ecological harm, this study evaluates and compares the performance of different fertilizer application technologies. In this study we combined remote and ground surveys to allow a comprehensive understanding of the impact of these technologies on soybean cultivation. The study focuses on deep placement of slow-release nitrogen fertilizers with coated urea at a 20 cm depth, conventional nitrogen fertilizer application, and manure organic fertilizer application. Remote surveys are conducted using advanced smart farming tools such as Unmanned Aerial Vehicle (UAV), ground surveys such as soil plant analysis development SPAD measurements, and soybean parameters to assess the impact of fertilizer application. This study revealed that deep placement fertilizer demonstrated better performance compared to other fertilizer application technologies for soybean cultivation. The findings from this study contribute to the advancement of sustainable agricultural practices and empower farmers with knowledge to make informed decisions for optimizing green soybean production.

The objective of this study was to evaluate the pain and inflammatory response in soft tissues using healing and prosthetic abutments of different diameters and lengths. Methods: The study population was rehabilitated with Astra tech EV single implants (Dentsply Sirona, Atlantis, Dentsply Sirona S.A., Barcelona, Spain), 4.2 and 4.8 millimetres in diameter in upper and lower maxilla and loaded with custom abutments digitally designed with the software of the company Dentsply Sirona (Atlantis WebOrder, Dentsply Sirona S.A., Barcelona, Spain), version 4.6.5, with a larger diameter than the healing abutment, to account for biomarkers through ELISA. Results: Rehabilitations in mandible and with healing abutments below 4.29 millimetres and rehabilitators below 2.18 millimetres elicited higher pain and inflammatory responses, and in turn higher interleukin 1β values. Conclusions: Greater inflammation was evident in cases in which healing abutments with reduced diameter were used in relation to the same subsequent rehabilitation with prosthetic abutments of larger diameter.

The Ionian Sea is a crucial intersection for various water masses in the Mediterranean. Its hydrography and dynamics play a significant role in the seawater budgets and biogeochemistry of the neighboring sub-basins. Multiple theories have been formulated to gain a better understanding of the Ionian dynamics. These theories primarily attribute the variability of the near-surface Ionian circulation to internal processes. Here, we utilize horizontal currents and temperature-salinity profiles from the Copernicus reanalysis to examine the contribution of baroclinic modes to the variability of the basin horizontal circulation. Our findings demonstrate that, although the basin vertical structure is characterized by three layers, the primary patterns of the Ionian circulation can be attributed to the first baroclinic mode. This mode, along with the barotropic mode, accounts for over 85% of the overall variability in the Ionian circulation, suggesting that only one of the three interfaces separating the different water masses in the basin is dynamically active. We estimate the depth of this interface to be about 490 m. Additionally, our analysis shows that more than 90% of the kinetic energy over the water column is localized above this interface, indicating that the deep layer of the Ionian is dynamically nearly inert.

Schizoaffective disorder and its classification have always been a topic of discrepancy among researchers. The overlapping presentations of schizoaffective disorder, schizophrenia and psychotic bipolar disorder makes it difficult to classify and diagnose. This study is a narrative review of literatures and genetic and epidemiological research evidences, done to determine the similarities and differences between schizoaffective and psychotic bipolar disorder. Beginning from the introduction of schizoaffective disorder as "schizoaffective psychosis" by Kasanin in 1933, various researchers have proposed different views regarding the diagnosis and classifications for schizoaffective disorder. DSM-III considered schizoaffective disorder as a diagnosis of exclusion as it fails to fit the definite diagnostic criteria of schizophrenia, major affective disorders, or schizophreniform disorder. DSM-V updated the criteria of schizoaffective disorder and stated it as a life time illness rather than being an episodic disorder as in DSM-IV and hence is more reliable. However, some studies show that schizoaffective disorder patients are more like schizophrenia than mood disorder. It still remains unclear whether schizoaffective disorder is a heterogenous disease, a form of schizophrenia, a form of mood disorder or a midpoint in the continuation spectrum of schizophrenia and psychotic bipolar disease.

3D object detection is essential for an accurate and reliable autonomous driving system. Currently, the methods used by the state-of-the-art two-stage detectors are not flexible enough and their fea-ture extraction capabilities are very limited to cope effectively with the disorder and irregularity of point clouds. In this paper, we combine the advantages of both PV-RCNN and PAConv (Position Adaptive Convolution) to create a completely new network, FANet, in order to overcome the ir-regularity and disorder of point clouds. The convolution in our network builds convolutional ker-nels from a basic weight matrix, whose combined coefficients are learned adaptively by LearnNet from relative points. This network allows for flexible modeling of complex spatial variations and geometric structures in the 3D point cloud, enabling better extraction of point cloud features and producing high-quality 3D proposal boxes. Compared to other methods, FANet is superior in terms of 3D object detection accuracy. Extensive experiments on the KITTI dataset have shown a signif-icant improvement in our approach.

In this paper, we present the idea of Self Supervised learning on the Shape Completion and Classification of point clouds. Most 3D shape completion pipelines utilize autoencoders to extract features from point clouds used in downstream tasks such as Classification, Segmentation, Detection, and other related applications. Our idea is to add Contrastive Learning into Auto-Encoders to learn both global and local feature representations of point clouds. We use a combination of Triplet Loss and Chamfer distance to learn global and local feature representations. To evaluate the performance of embeddings for Classification, we utilize the PointNet classifier. We also extend the number of classes to evaluate our model from 4 to 10 to show the generalization ability of learned features. Based on our results, embedding generated from the Contrastive autoencoder enhances Shape Completion and Classification performance from 84.2% to 84.9% of point clouds achieving the state-of-the-art results with 10 classes.

Vienna Atomic Line Database (VALD) contains data on atomic and molecular energy levels and parameters of spectral lines required for stellar spectra analysis. Hundreds of millions lines for fine spectral synthesis and for opacity calculations are collected in present version of VALD (VALD3). Critical evaluation of the data and the diversity of extraction tools support high popularity of VALD among users. The data model of VALD3 incorporates obligatory links to the bibliography making our database more attractive as publishing platform for data producers. The VALD data quality and completeness are constantly improving allowing better reproduction of stellar spectra. To illustrate continuous evolution of the data content we present a comparative analysis of the recent experimental and theoretical atomic data for Fe-group elements, which will be included in the next VALD release. This release will also include a possibility for extracting the line data with full isotopic and hyperfine structures.

The present contribution introduces the task dependent comfort zone as a base placement strategy for mobile manipulators using different manipulability measures. Four different manipulability measures depending on end-effector velocities, forces, stiffness, and accelerations are considered. By evaluating a discrete subspace of the manipulator workspace with these manipulability measures and by using image processing algorithms, a suitable goal position for the autonomous mobile manipulator was defined within the comfort zone. This always ensures a certain manipulator manipulablity value with a lower limit in respect to the maximum possible manipulability in the discrete subspace. Results are shown for three different mobile manipulators using the velocity dependent manipulability measure in a simulation.

Spinal Cord Stimulation (SCS) is an effective and validated treatment to address chronic refractory neuropathic pain in Persistent Spinal Pain Syndrome-Type 2 (PSPS-T2) patients. Surgical SCS lead placement is traditionally performed under general anesthesia due to its invasiveness. In parallel, recent works have suggested that Awake Anesthesia (AA), consisting in Target Controlled Intra-Veinous Anesthesia (TCIVA), could be an interesting tool to optimize lead anatomical placement using patient intra-operative feedback. We hypothesized that combining AA with Minimal Invasive Surgery (MIS) could improve SCS outcomes. The goal of this study was to evaluate SCS lead performance (defined by the area of pain adequately covered by paraesthesia generated via SCS), using an intraoperative objective quantitative mapping tool, and secondarily to assess pain relief, functional improvement and change in quality of life with a composite score. We analyzed data from a prospective multicenter study (ESTIMET) to compare the outcomes of 115 patients implanted with MIS under AA (MISAA group) or General Anesthesia (MISGA group), or by Laminectomy under General Anesthesia (LGA group). All in all, MISAA appears to show significantly better performance in terms of patient pain coverage, as well as improved secondary outcomes. One step further, our results suggest that MISAA combined with intra-operative hypnosis could potentialize patient intraoperative cooperation and could be proposed as a personalized package offered to PSPS-T2 patients eligible for SCS implantation in highly dedicated neuromodulation centers.

Well placement optimization in a given geological setting for a fractured geothermal reservoir is a prerequisite for enhanced geothermal operations. High computational cost associated in the framework of fully coupled thermo-hydraulic-mechanical (THM) processes in a fractured reservoir simulation, makes the well positioning as a missing point in developing a field scale investigation. Here, in this study, we shed light on this topic through examining different injection-production well (doublet) position in a given real fracture network. Water and CO2 are used as working fluids for geothermal operations and importance of well positions are examined using coupled THM numerical simulations for both the fluids. Results of this study are examined through the thermal breakthrough time, mass flux and the energy extraction potential to assess the impact of well position in a two-dimensional reservoir framework. Almost ten times of the difference between the final amount of heat extraction is observed for different well position but with the same well spacing and geological characteristics. Furthermore, stress field is be a strong function of well position that is important with respect to the possibility of unwanted stress development. As part of the MEET project, this study recommends to perform similar well placement optimization study for each fracture set in a fully coupled THM manner before a field well drilling.

In the past, Unmanned Aerial Vehicles (UAVs) were mostly used in the military operations to prevent pilot losses. Nowadays, the fast technological evolution enables the production of a class of cost-effective UAVs which can service a plethora of public and civilian applications, specially when configured to work cooperatively to accomplish a task. However, designing a communication network among the UAVs is challenging task. In this article, we propose a centralized UAV placement strategy, where UAVs are used as flying access points forming a mesh network, providing connectivity to ground nodes deployed in a target area. The geographical placement of UAVs is optimized based on a Multi-Objective Evolutionary Algorithm (MOEA). The goal of the proposed scheme is to cover all ground nodes using a minimum number of UAVs, while maximizing the fulfillment of their data rate requirements. The UAVs can employ different data rates depending on the channel conditions, which are expressed by the Signal-to-Noise-Ratio (SNR). In this work, elitist Non-Dominated Sorting Genetic Algorithm II (NSGA-II) is used to find a set of optimal positions to place UAVs, given the positions of the ground nodes. We evaluate the trade-off between the number of UAVs used to cover the target area and the data rate requirement of the ground nodes. Simulation results show that the proposed algorithm can optimize the UAV placement given the requirement and the positions of the ground nodes in the geographical area.

Several empirical studies indicate that the lack of financing is one of the main barriers that affects the economic growth of small and medium enterprises (SMEs). The main objective of this investigation was to determine to what extent the economic sector; enterprise size; the characteristics inherent to the enterprise; legal status; the variables linked to the performance of the enterprise; and the attributes of the owner influence the access to bank financing of SMEs in Mexico. Using a discrete response probit regression model, the impact of enterprises characteristics on the probability of obtaining a bank loan was determined. The data collected is from the Enterprise Surveys of Mexico, carried out by the World Bank. The sample of 1,480 enterprises is representative by enterprise size, by economic sector, and by region. The research has a quantitative approach with a correlational scope and a non-experimental and transectional design. One of the main results highlights that the determinants with the greatest influence on access to bank financing are: age, the small size, foreign participation, and the manufacturing sector. These results are consistent with other empirical studies, as well as with the pecking order theory and the financial life cycle theory.

Nowadays, cloud computing is one of the important and rapidly growing paradigms that extend its capabilities and applications in various areas of life. The cloud computing system challenges many security issues, such as scalability, integrity, confidentiality, and unauthorized access, etc. An illegitimate intruder may gain access to the sensitive cloud computing system and use the data for inappropriate purposes that may lead to losses in business or system damage. This paper proposes a hybrid unauthorized data handling (HUDH) scheme for Big data in cloud computing. The HUDU aims to restrict illegitimate users from accessing the cloud and data security provision. The proposed HUDH consists of three steps: data encryption, data access, and intrusion detection. HUDH involves three algorithms; Advanced Encryption Standards (AES) for encryption, Attribute-Based Access Control (ABAC) for data access control, and Hybrid Intrusion Detection (HID) for unauthorized access detection. The proposed scheme is implemented using Python and Java language. Testing results demonstrate that the HUDH can delegate computation overhead to powerful cloud servers. User confidentiality, access privilege, and user secret key accountability can be attained with more than 97% high accuracy.

The world is growing very rapidly concerning technology. In the next-generation Internet, the existing architecture requires to be upgraded from Host-Centric Networking paradigm to Information-centric networking architecture. The unique aspect of information-centric networking is in-network cashing. Due to the system augmentation and In-network cashing technique, this novel system needs extremely high content security to ensure system integrity and maintenance. 5G network may be supported by the Information-Centric Network due to its high data transmission rate. In order to handle the serious security issues such as attack on confidentiality, authentication and integrity of the content, a Digital Signature based Access Control Mechanism in Information-Centric Network (DSAC) scheme is proposed to enhance security of ICN. Briefly, this new scheme uses Digital Signature, hash function, Trusted Third Party (TTP) and Proxy TTP. The client request for content, after receiving a request, the content provider generates and encrypts content with the digital signature and random value ‘k’ hash function and send it to TTP. After the signing process, the TTP sends the encryption hash key to Proxy TTP. In this proposed scheme authentication, confidentiality, the integrity aspects of the content security are improved.

Multimedia materials represent a promising approach for the Geoheritage promotion. Despite Geology is normally associated with natural environments, new tendencies are projected towards a better knowledge of the “geological reason” for the location and the development of urban settlements. The urban environment is, in fact, a perfect “laboratory” for opening the scientific topics to a broad audience. In this paper the experience of a geological exhibition organized in the town of Perugia city (Umbria, central Italy) is illustrated, highlighting the SECRET (SEe and CREaTe) for an effective dissemination activity. Panels, interactive tools, laboratories and trekking tours outside the museum represent the main activities, which counted more than eight thousand visitors in a few months. Moreover, the exhibition was the starting point for ongoing projects on geotourism in the city with important consequences in terms of visibility and financial return.

With the development of IoT technology, various information resources, such as social resources and physical resources, are deeply integrated for different comprehensive applications. Social networking, car networking, medical services, video surveillance and other forms of IoT information Service model gradually change people's daily life. Facing the vast amounts of IoT information data, IoT search technology is used to quickly find accurate information to meet real-time search needs of users. However, IoT search requires to use a large number of user privacy Information, such as personal health information, location information, social relations information, to provide personalized services. User privacy information will meet security problems if an effective access control mechanism is missing during the IoT search process. Access control mechanism can effectively monitor the access activities of resources, and ensure authorized users to access information resources under legitimate conditions. This survey examines the growing literature on access control for IoT search. Problems and challenges of access control mechanism are analyzed to facilitate the adoption of access control solutions in real-life settings. This paper aims to provides theoretical, methodological and technical guidance for IoT search access control mechanism in large-scale dynamic heterogeneous environment. Based on the literature study, we also analyzed future development direction of access control in the age of IoT.

Gyroscopes are fascinating instruments with a history of about 200 years. When J.G.F. Bohnenberger presented his machine to his students in 1810 at the University of Tuebingen, Germany, nobody could have foreseen that this fascinating development would be used for complex orientation and positioning. At the University of Stuttgart, Germany, a collection of 160 exhibits is available and in transition for a sustainable future. Here, the systems are digitized in 2D, 2.5D and 3D and are made available for a world-wide community using OpenAccess platforms. The technologies being used are Computed Tomography, Computer Vision, Endoscopy and Photogrammetry. The workflows for combining voxel representations and colored point clouds are described, to create Digital Twins of the tangible assets. Advantages and disadvantages are discussed und work for near future is outlined in this new and challenging field of Tech Heritage digitization.

Telerehabilitation is an appealing service delivery option for optimising recovering. Internationally, the equity of telerehabilitation services for people from culturally and linguistically diverse (CALD) backgrounds has been questioned. Using a 31-item survey, our study explored the access, readiness, and willingness of 260 patients to use allied health telerehabilitation services for adults receiving interventions from a large tertiary health service located in Sydney, Australia. Overall, 72% patients reported having access to technology, 38% met our readiness criteria, and 53% reported willingness to engage in telerehabilitation. There were no difference in access, readiness and willingness to engage in telerehabilitation between patients from CALD and non-CALD backgrounds. Age was the only factor that influenced access, readiness and willingness to engage in telerehabilitation. Past experience of telerehabilitation was related to willingness, but not access or readiness. Findings highlight the importance of ensuring positive patient experiences to promote ongoing willingness to use telerehabilitation. Efforts are needed to improve patients’ digital health literacy, especially patients from older age groups, to ensure equitable access to telerehabilitation services.