Precise monitoring of individual crop growth and health status is crucial for precision agriculture practices. However, traditional manual inspection methods are time-consuming, labor-intensive, and often lack the spatial resolution required for detailed analysis. This research addresses the need for efficient and high-resolution crop monitoring by leveraging Unmanned Aerial Vehicle (UAV) imagery and advanced computational techniques. The primary objective was to develop a methodology for precise identification, extraction, and monitoring of individual corn crops throughout their growth cycle. This was achieved by integrating UAV-derived data with image processing, computational geometry, and machine learning techniques. UAV imagery was ac-quired bi-weekly at altitudes of 40m and 70m, capturing the entire growth cycle of a corn crop from planting to harvest. A time-series Canopy Height Model (CHM) was generated by analyzing the differences between the Digital Terrain Model (DTM) and the Digital Surface Model (DSM) derived from the UAV data. Local spatial analysis and image processing techniques were em-ployed to determine the local maximum height of each crop. Subsequently, a Voronoi data model was developed to delineate individual crop canopies, successfully identifying 13,000 out of 13,050 corn crops in the study area. For enhanced accuracy in canopy size delineation, vegetation indices were incorporated into the Voronoi model segmentation, refining the initial canopy area esti-mates by eliminating interference from soil and shadows. The proposed methodology enables precise estimation and monitoring of crop canopy size, height, biomass reduction, lodging, and stunted growth over time, providing valuable insights for precision agriculture practices. This work contributes to the scientific community by demonstrating the potential of integrating UAV technology, computational geometry, and machine learning for accurate and efficient crop mon-itoring at the individual plant level.

In eastern part of Ethiopia groundnut is very commonly intercropped with sorghum. Even though intercropping of sorghum with groundnut is practiced in the eastern part of Ethiopia the population density at what ratio should not be known. Therefore determining the population ratio is found to be crucial to draw management options. The study was conducted at two locations at Fadis (on station) and Babile (sub- station). Sorghum variety (Teshale) and groundnut (Fetene) were used as planting materials. All agronomic data were collected and analyzed by using GenStat software. Significant different were obtained among the treatments. The research result showed that, there were significance difference for both sorghum and ground nut yield per hectare in the years (2014 and 2015) among treatments. The result over time(in 2014 and 2015) at Fadis and Erer showed that the highest sorghum and groundnut yield per hectare were obtained/harvested from the intra row spacing of 25cmx20cm and 30cmx20cm intercropping sorghum with ground nut system with (1.27 and 1.31) respectively. The highest LER (1.31) and highest GMV (10218.00 ETBr/ha) were obtained from the intercropping of 30cmx20cm (Sorghum & groundnut). Clearly showed that, with intercropping of sorghum and Groundnut, it is possible to produce additional yield of sorghum without significant reduction in groundnut yield. As a result of this, the intra spacing of the main crop (sorghum) 25cm and 30cm and for the subsidiary crop (groundnut) 20cm was recommended for further production in the study areas of eastern Harerghe zone and similar agro-ecologies.

Rice, as a staple crop feeding billions, faces constant threats from various diseases jeopardizing global food security. Precise understanding of disease resistance mechanisms is crucial for developing resilient rice varieties. Traditional genetic mapping methods, such as QTL mapping, provide valuable insights into the genetic basis of diseases. However, the complex nature of rice diseases demands a holistic approach to gain accurate knowledge of it. Omics technologies, including genomics, transcriptomics, proteomics, and metabolomics, enable a comprehensive analysis of biological molecules, uncovering intricate molecular interactions within the rice plant. Integration of various mapping techniques using multi-omics data has revolutionized our understanding of rice disease resistance. By overlaying genetic maps with high-throughput omics datasets, researchers can pinpoint specific genes, proteins, or metabolites associated with disease resistance. This integration enhances the precision of disease-related biomarkers with better understanding of their functional roles in disease resistance. Improvement of rice breeding for disease resistance through this integration represents a significant stride in agricultural science because better understanding of the molecular intricacies and interactions underlying disease resistance architecture leads to more precise and efficient development of resilient and productive rice varieties. In this review, we explore how the integration of mapping and omics data can give a transformative impact on rice breeding for enhancing disease resistance.

In recent years, the utilization of machine learning algorithms and advancements in Unmanned Aerial Vehicle (UAV) technology have marked significant shifts in remote sensing practices. In particular, the integration of machine learning with physical models and their application in UAV-satellite data fusion have emerged as two prominent approaches for estimating vegetation biochemistry. This study evaluates the performance of five machine learning regression algorithms (MLRAs) for mapping crop canopy chlorophyll at the Kellogg Biological Station (KBS) in Michigan, USA, across three scenarios: (1) application to Landsat 7, RapidEye, and PlanetScope satellite images; (2) application to UAV-satellite data fusion; and (3) integration with the PROSAIL radiative transfer model (hybrid methods PROSAIL + MLRAs). The results indicate that the majority of the five MLRAs utilized in UAV-satellite data fusion perform better than the five PROSAIL + MLRAs. The general trend suggests that the integration of satellite data with UAV-derived information, including the normalized difference red-edge index (NDRE), canopy height model, and leaf area index (LAI), significantly enhances the performance of MLRAs. The UAV-RapidEye dataset exhibits the highest coefficient of determination (R2) and the lowest root-mean-square errors (RMSE) when employing kernel ridge regression (KRR) and Gaussian processes regression (GPR) (R2 = 0.89 and 0.89 and RMSE = 8.99 µg/cm2 and 9.65 µg/cm2, respectively). Similar performance is closely observed for the UAV-Landsat and UAV-PlanetScope datasets (R2 = 0.86 and 0.87 for KRR, respectively). For the hybrid models, maximum performance is attained with Landsat data using KRR and GPR (R2 = 0.77 and 0.51 and RMSE = 33.10 µg/cm2 and 42.91 µg/cm2, respectively), followed by R2 = 0.75 and RMSE = 39.78 µg/cm2 for PlanetScope data upon integrating partial least squares regression (PLSR) into the hybrid model. Across all hybrid models, RapidEye data yielded the most stable performance, with R2 ranging from 0.45 to 0.71 and RMSE ranging from 19.16 µg/cm2 to 33.07 µg/cm2. The study highlights the importance of synergizing UAV and satellite data which enables effective monitoring of canopy chlorophyll in small agricultural lands.

About a decade ago, active optical crop canopy sensors are being used to manage in-season variable nitrogen (N) fertilization in cornfields to match the plant demand that occurs mid season, increasing the efficiency compared to broadcast N applications. There were also initiatives of using ultrasonic sensors to measure plant height on-the-go for N application and crop water demand estimation, but no studies have integrated the optical, ultrasonic and canopy temperature for crop water stress assessment. The objective of this chapter is to evaluate the crop water status using infrared thermometry integrated with optical and ultrasonic sensors. Specifics objectives are: (i) evaluate the corn canopy temperature under different previous crop, N rates and irrigation levels; (ii) test a procedure for water stress assessment in commercial cornfields using the integration of sensors, (iii) correlate plant based sensor measurements (N status, plant height and canopy temperature) with grain yield, soil attributes and detailed topographical features, and (iv) study the spatial dependence of canopy temperature. This study was conducted in one small plot study area and on three producer’s fields in 2010. The small plot experiment consisted of two irrigation levels (70 and 100% of evapotranspiration – ET), two previous crop schemes (corn after corn – CC and corn after soybeans – CS), and four N rates (0, 75, 150, 225 kg N ha^-1). Canopy temperature, optical reflectance and plant height was measured from R2 until R6 in the small plots. At the producer’s fields, three long strips across center pivots were used to have a non-limited N and water crop and then continuous georeferenced sensors measurements were taken during side-dress (V11 growth stage) in about 10 hectares in each field. In the small plot study the crop canopy temperature was influenced by the irrigation levels and N rates. The procedure proposed could be used to identify zones in the producer’s field where water stress can be a yield limiting factor other than N derived. Inside the zones considered that water stress played a major whole, there were low correlations between plant height, plant N status and canopy temperature, indicating that the canopy temperature had more influence from water stress than vegetation cover. Concave and lower elevation areas had higher yields compared to convex and high elevation, showing that the detailed elevation mapping can be beneficial to delineate stables zones that possibly could be used in variable irrigation systems. The spatial dependence of canopy temperature was over 65 meters across producers’ sites, showing that the commercial high clearance applicator’s swath width was adequate to obtain accurate maps. The integration of plant N status, plant height and canopy temperature was beneficial to detect water stressed zones in the field. Opportunities can be foresee also for on-the-go N fertilization using integration of these sensors because is likely that water stress can be confounded with different N supply during the growing season and in different zones in the field.

In recent years, the integration of sensors in agriculture has emerged as a pivotal catalyst for transforming conventional farming practices into precision agriculture. Sensor application is impacting the everyday objects that enhance human life. In this special issue, the main objective was to address recent advantages of sensor application in agriculture covering a wide range of topics in this field. This provides overview of diverse application of sensors in agriculture, highlighting their role in enhancing productivity, sustainability, and resource management. sensors are instrumental in monitoring various agriculture parameter such as soil condition, weather, crop health and livestock wellbeing. By collecting real-time data and providing valuable insight, sensors enable precision farming, optimize resource allocation, and minimize environmental impacts. we have to explore the key sensor types used in agriculture, their applications, benefits, and future prospects, emphasizing their crucial roles in the modernization of agriculture and global quest for food security and crop production.

Powdery mildew is a severe disease causing substantial yield losses in wheat production worldwide. The Chinese wheat landrace Changanhongmai (CAHM) exhibits high resistance to the physiological race E09 of powdery mildew. This study aims to characterize the powdery mildew resistance gene in CAHM, and develop molecular markers for marker-assisted selection of wheat. To investigate the genetic characteristics of this resistant gene, we developed F1 plants, F2 generation population, and F2:3 families from a cross between CAHM and SY225. Genetic analysis demonstrated that all F1 plants were resistant to the disease, while the ratio of resistant to susceptible plants was 3: 1 in both the F2 population and F2:3 families, indicating that CAHM is inherited in a manner of single dominant powdery mildew resistance gene, which was tentatively designated as PmCAHM. By using bulk segregation analysis, we constructed a genetic map encompassing Xgwm273, Xwmc626, Xgwm11, Xgwm18, Xgdm28, Xgpw7812, Xgpw5195, Xwmc694 and PmCAHM. Among these markers, Xgpw7812 and Xgpw5195 were flanking markers tightly linked to PmCAHM at a genetic distance of 2.5 cM and 8.4 cM, respectively. Furthermore, nullisomic-tetrasomic analysis revealed that PmCAHM is located on chromosome 1B. These results indicate that PmCAHM differs from the internationally recognized powdery mildew resistance genes in both location and source. In addition, a new germplasm/line NW1748 with large seeds and powdery mildew resistance was developed from the cross and back cross populations of Fengyou 1718 (FY1718)/CAHM//FY 1718. Therefore, PmCAHM can serve as a novel powdery mildew resistance source for breeding of wheat by using NW1748 as the donor in the future.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Climate change is challenging the agricultural sector worldwide. The pressure exerted by the altered thermal conditions drives the zonal shift for various cultivations. This study presents the multiyear analysis of the Growing Degree Days (GDD) index over the Northern Mediterranean Basin (NMB), focused on the high-value vine cultivation derived from the E-OBS dataset. To handle this extensive environmental dataset, R-language scripts and packages were applied, along with the capabilities of the GIS software. The investigated time period spans from 1969 to 2018, and the performed analysis indicates a broad shift/expansion in areas of GDD exceeding 2000 heat units. The extracted results specify the viticultural areas where the GDD index surpasses the suitable values for vine cultivation, owing to the increase of the thermal stress risk. In addition to mapping areas with GDD ≥ 2000, spatial calculations of the surface of areas meeting this criterion per country in the study area were made. In the northern parts of the NMB, the rise of the GDD index values indicates the establishment of vine plantations in the future.

Adlay seed samples were collected from 3 adlay growing regions (Yeoncheon, Jeonnam and Eumseong regions) in Korea during 2012. Among all the samples collected, 400 seeds were tested for fungal occurrence by standard blotter and test tube agar methods and different taxonomic groups of fungal genera were detected. The most predominant fungal genera encountered were Fusarium, Phoma, Alternaria, Cladosporium, Curvularia, Cochliobolus and Leptosphaerulina. The occurrence of Fusarium species were 45.6% and based on the combined sequences of two protein coding genes, EF-1a, Beta-tubulin and phylogenetic analysis, 10 species were characterized as F. incarnatum (11.67%), F. kyushense (10.33%), F. fujikuroi (8.67%), F. concentricum (6.00%), F. asiaticum (5.67%), F. graminearum (1.67%), F. miscanthi (0.67%), F. polyphialidiom (0.33%), F. armeniacum (0.33%) and F. thapsinum (0.33%). The ability of these isolates to produce mycotoxins fumonisin (FUM) and zeralenone (ZEN) were tested by ELISA quantitative analysis method. The result revealed that fumonisin (FUM) was produced only by F. fujikuroi and zeralenone (ZEN) by F. asiaticum & F. graminearum. Mycotoxigenic species were then examined for their morphological characteristics to confirm their identity. Morphological observations of the species correlated well with their molecular identification and confirmed as F. asiaticum, F. fujikuroi and F. graminearum.

Effective agricultural management in maize production operations starts with the early quantification of seedlings. Accurately determining plant presence allows growers to optimize planting density, allocate resources, and detect potential growth issues early on. This study presents an in-depth analysis of multiple object detection models used by drones to count maize seedlings, while concurrently investigating the influence of planting density, flight altitude, and plant growth stage. The findings of this study demonstrate that one-stage models are able to more accurately detect maize seedlings than two-stage models. In particular, YOLOv8n exhibits outstanding performance, achieving an F1-score of over 0.92 under various density conditions and maintaining a stable performance, especially under densities below 105,000 plants/ha. Additionally, planting density and growth stage were observed to significantly affect detection accuracy, with performance declining as density and growth stage increased. Image resolution and detection were impacted by flight altitude, with lower flights producing higher-quality results. Ultimately, YOLOv8n displays optimal performance under various conditions, providing crucial data to support intelligent decision-making. This research offers valuable insights into the application of object detection technology and provides a basis for the future development of precision agriculture.

Ecosystem physical structure, defined by the quantity and spatial distribution of biomass, influences a range of ecosystem functions. Remote sensing tools permit the non-destructive characterization of canopy and root features, potentially providing opportunities to link above- and belowground structure at fine spatial resolution in functionally meaningful ways. To test this possibility, we employed ground-based portable canopy lidar (PCL) and ground penetrating radar (GPR) along co-located transects in forested sites spanning multiple stages of ecosystem development and, consequently, of structural complexity. We examined canopy and root structural data for coherence at multiple spatial scales ≤ 10 m within each site using wavelet analysis. Forest sites varied substantially in vertical canopy and root structure, with leaf area index and root mass more evenly distributed by height and depth, respectively, as forests aged. In all sites, above- and belowground structure, characterized as mean maximum canopy height and root mass, exhibited significant coherence at a scale of 3.5-4 meters, and results suggest that the scale of coherence may increase with stand age. Our findings demonstrate that canopy and root structure are linked at characteristic spatial scales, which provides the basis to optimize scales of observation. Our study highlights the potential, and limitations, for fusing lidar and radar technologies to quantitatively couple above- and belowground ecosystem structure.

Emulsifiers like egg yolk (EY) are necessary for the formation of mayonnaise, which is an oil-in-water type colloid. This study aimed to assess the potential of defatted soybean powder treated with supercritical carbon dioxide (DSF-SC) in enhancing the quality of plant-based may-onnaise as plant-based alternatives gain popularity. This study involved producing DSF-SC and comparing its quality attributes to those of mayonnaise made with varying amounts of control soy flour (CSF), DSF-SC, and EY. It was found that mayonnaise made with DSF-SC, with increased emulsifier quantity, showed better emulsion stability, viscosity, and smaller, more uniform particle size compared with CSF mayonnaise. Additionally, DSF-SC mayonnaise was overall rated higher in sensory evaluation. The addition of approximately 2% DSF-SC positively influenced the emul-sion and sensory properties of the vegan mayonnaise, making DSF-SC a promising plant-based alternative emulsifier for replacing animal ingredients.

Phenotypic characterization of crop genotypes is an essential yet challenging aspect of crop management and agriculture research. Digital sensing technologies are rapidly advancing plant phenotyping and speeding-up crop breeding outcomes. However, off-the-shelf sensors might not be fully applicable and suitable for agriculture research due to diversity in crop species and specific needs during plant breeding selections. Customized sensing systems with specialized sensor hardware and software architecture provide a powerful and low-cost solution. This study designed and developed a fully integrated Raspberry Pi-based LiDAR sensor named CropBioMass (CBM), enabled by internet of things to provide a complete end-to-end pipeline. The CBM is a low-cost sensor, provides high-throughput seamless data collection in field, small data footprint, injection of data onto the remote server, and automated data processing. Phenotypic traits of crop fresh biomass, dry biomass, and plant height estimated by CBM data had high correlation with ground truth manual measurements in wheat field trial. The CBM is readily applicable for high-throughput plant phenotyping, crop monitoring, and management for precision agricultural applications.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

Automation of forest field reference data collection has been an intensive research objective for laser scanning scientists ever since the invention of terrestrial laser scanning more than two decades ago. Recently, it has been proposed that such automated data collection providing both the tree heights and stem curves would require a combination of above-canopy UAV point clouds and terrestrial point clouds. In this study, we demonstrate that an under-canopy UAV laser scanning system utilizing a rotating laser scanner can alone provide accurate estimates of the canopy height and the stem volume for the majority of the trees in a boreal forest. To this end, we mounted a rotating laser scanner based on a Velodyne VLP-16 sensor onboard a manually piloted UAV. The UAV was commanded with the help of a live video feed from the onboard camera of the UAV. Since the system was based on a rotating laser scanner providing varying view angles, all important elements such as treetops, branches, trunks, and ground could be recorded with laser hits. In an experiment including two different forest structures, namely sparse and obstructed canopy, we showed that our system can measure the heights of individual trees with a bias of -20 cm and a standard error of 40 cm in the sparse forest and with a bias of -65 cm and a standard error of 1 m in the obstructed forest. The accuracy of the obtained tree height estimates was equivalent to airborne above-canopy UAV surveys conducted in similar forest conditions. The higher underestimation and higher inaccuracy in the obstructed site can be attributed to three trees with a height exceeding 25 m and the applied laser scanning system VLP-16 that had a limited height measurement capacity when it comes to trees taller than 25 m. Additionally, we used our system to estimate the stem volumes of individual trees with a standard error at the level of 10%. This level of error is equivalent to the error obtained when merging above-canopy UAV laser scanner data with terrestrial point cloud data. Future research is needed for testing new sensors, for implementing autonomous operation inside canopies through collision avoidance and navigation through canopies, and for developing robust methods that work also with more complex forest structure. The results show that we do not necessarily need a combination of terrestrial point clouds and point clouds collected using above-canopy UAV systems in order to accurately estimate the heights and the volumes of individual trees.

Variable nitrogen(N) rate fertilization based on remote sensing is challenging for cotton production fields, but active crop canopy sensors (ACS) appear as an alternative to make this practical on farm since they can be used at night as well. The crop spatial variability in inherent in crop production in general, and not on-the-go solutions can be used with this type of active sensing technologies. Thus, the purpose of this study was to investigate the potential of two vegetation indices to identify the N requirement variability for cotton plants and to develop prototype algorithms for topdressing nitrogen variable rate on commercial and experimental areas, using the N-sufficiency methodology based on virtual reference. The concept of virtual reference is to use a histogram to characterize the vegetation index of properly fertilized plants without establishing an N-rich plot as a reference strip. The experiment was conducted in strips with four different N rates (0, 45, 90 and 180 kgN ha^-1) during the 2015, 2016, 2017 and 2018 crop seasons in partnership with large cotton producers in Mato Grosso and also in experimental area of Embrapa Agrosilvopastoral. Two algorithms for variable rate nitrogen fertilization for cotton were developed, namely: 1) N recommendation algorithm for cotton in commercial production system: N rate (kg.N ha^-1) = -234.79 ISN² + 49,879 ISN + 195.15; R² = 0.97; and 2) for cotton grown in experimental area: N dose (kgN ha^-1) = -174.73 ISN² - 107.21 ISN + 306.78; R² = 0.94.

This paper presents a piezoresistive pressure sensor with a shield layer for improved stability. Compared with the conventional piezoresistive pressure sensors, p-type piezoresistors are covered by an n-type shield layer, which is formed by ion implantation. The proposed pressure sensors have been successfully fabricated by bulk micromachining techniques. The impact of electrical field on piezoresistors is studied by simulation. The temperature drift of the pressure sensor has been investigated by both simulation and experimental measurement. Characteristics of developed pressure sensors are tested from -40 C to 125 C. A sensitivity of 0.022 mV/V/KPa and a maximum non-linearity of 0.085% FS are measured for the fabricated sensor in a pressure range of 1 MPa. The temperature coefficients of resistance of shielded piezoresistors are found to be smaller than those of un-shielded ones. It is demonstrated that the shield layer is able to reduce the drift caused by electrical field and ambient temperature variation.

This review provides a comprehensive and updated information on chalcones, presenting their sources, methods of identification and properties putting emphasis on applications in agricultural industry. Vast exploitation of synthetic pesticides led to the weed and pest resistance issue, causing economic loss but more importantly health risk due to pesticide overuse. Because one of the aim of the European Green Deal 2030 is the Farm to Fork strategy which targets on reducing by 50% the use of chemical pesticides by 2030, and push towards natural pesticides which are more environmentally friendly and restore natural resources, chalcones and their derivatives seem to fit perfectly. They have herbicidal, fungicidal, bactericidal and antiviral properties. Moreover, chalcones are naturally occurring substances, known for their favorable health effect for years, working on many areas. This review is complementary to the previous ones describing chalcones use in agriculture, updates them but additionally shows methods of detection.

Wearable technology has been proposed as a potential tool to change the way of human life, such as the smart bracelet and the Google Glass. In the wearable technology, the inertial sensor has great significance in tracking the object movements. The paper focused on detecting the movements of user’s finger based on the inertial sensor to give the control signals. Firstly, the attitude matrix, which represented the transformation relation of carrier coordinate system and the navigation coordinate system, was obtained. Secondly, the attitude matrix was expressed based on the quaternions. Thirdly, the finger gesture was processed by the attitude matrix to get the attitude angle. Finally, the robot was controlled by attitude angle to make the moving action. The experimental results showed the detection of the finger movement is effective.

During choriogenesis in insects, chorion (eggshell) is formed by surrounding follicular epithelial cells in ovarioles. However, the regulatory endocrine factor(s) activating choriogenesis and the chemical components on eggshell deserve further exploration. In two representative Coleopterans, a Coccinellid Henosepilachna vigintioctopunctata and a Chrysomelid Leptinotarsa decemlineata, genes encoding the 20-hydroxyecdysone (20E) receptor heterodimer, ecdysone receptor (EcR) and ultraspiracle (USP), and two chitin biosynthesis enzymes UDP-N-acetylglucosamine pyrophosphorylase (UAP) and chitin synthase (ChS1), were highly expressed in ovaries of the young females. RNA interference (RNAi)-aided knockdown of either HvEcR or Hvusp in H. vigintioctopunctata inhibited oviposition, suppressed the expression of HvChS1, and lessened the positive signal of Calcofluor staining on the chorions, which suggests the reduction of a chitin-like substance (CLS) deposited on eggshells. Similarly, RNAi of LdEcR or Ldusp in L. decemlineata constrained oviposition, decreased the expression of LdUAP1 and LdChS1, and declined CLS contents in the resultant ovaries. Knockdown of LdUAP1 or LdChS1 caused similar defective phenotypes, i.e., reduced oviposition and CLS contents in the L. decemlineata ovaries. These results, for the first time, indicate that 20E signaling activates choriogenesis in two Coleopteran species. Moreover, our findings propose the deposition of a CLS on the chorions.

As the global arid climate intensifies and the groundwater becomes increasingly scarce, drought stress has become a major challenge to plant growth and development worldwide, especially causing yield reduction and extinction of cultivated crops. In a large number of drought resistance studies, DNA methylation has been found dynamically associated with response to drought stress in plants by regulating gene expression and developments in plants, but the specific mechanisms are not yet clear. In this article, the current advances of research have been summarized on DNA methylation response to drought stress in various plant species, in terms of methylation detection methods, mechanisms of pattern changes (DNA de novo methylation, DNA maintenance methylation, and DNA demethylation), and its response to drought stress. With Most of the studies showed significant changes in genome or gene promoter methylation levels in plants subjected to drought stress, but the identification of the genes and pathways involved is still in the minority. The aim is to provide references for in-depth research on the response of plants to drought stress through epigenetics, and to uncover drought resistance genes regulated by DNA methylation, specific signaling pathways, and molecular mechanisms of action.

The Active Distribution Networks (ADNs) are Multi-Input Multi-Output (MIMO) systems with coupled dynamics which cause interactions among the control loops of the Distributed Energy Resources (DERs). This undesired effect lead to performance degradation in the voltage control. To mitigate the effects of these unavoidable coupling, the present paper proposes a systematic design procedure based on the analysis of the interaction's sources. In details, each DER is equipped with a double loop PI to control the active and reactive powers output by the Voltage Source Converter (VSC) which connects the DER to the network's node. Furthermore, to guarantee Ancillary Services (ASs), the two loops are coupled by a simple mechanism of cooperation of the active power to voltage regulation realized by a filtered droop law. To achieve voltage regulation with reduced loop interactions, the PI parameters and the filter's pulse are designed according to a two sequential steps procedure based on the (Internal Model Control) IMC technique. Simulation studies are finally presented to demonstrate that the proposed design method achieves both reduction of the loop interaction and robust voltage control in presence of model parameter uncertainty in the MIMO model.

Plants can utilize the different forms of nitrogen (N), including inorganic and organic N nutrients, and show the great difference in the utilizing efficiency of N-form among species and genotypes within a species. In our previous study, we found that Tibetan wild barley (XZ16) was better in utilization of organic nitrogen in comparison with cultivated barley (Hua30). In this study, metabolite profiles of the two barley genotypes were comprehensively compared in their response to four N forms, including nitrate (NO3-), ammonium (NH4+), urea and glycine. Macro-and micro-nutrient concentrations in shoots were mostly found higher in nitrate and urea treatments than in ammonium and glycine in both the genotypes. XZ16 had higher concentrations of nutrient ions in glycine treatment, but Hua30 accumulated more nutrients in ammonium treatment. Among the total 163 differentially expressed metabolites, highest up-regulation and highest down-regulation was found in XZ16 in glycine and urea treatments respectively. Some important metabolites such as proline, glutamine, serine, asparagine, L-homoserine, aspartic acid, putrescine, ornithine, 4-aminobutyrate were up-regulated in glycine treatment in both the genotypes with higher fold change in XZ16 than in Hua30. Similarly, fructose-6-PO4, aconitic acid and isocitrate were only up-regulated in XZ16 in glycine treatment. Here, we concluded that the genotype XZ16 exhibited higher response to glycine treatment, while Hua30 showed higher response to NH4+ treatment which is attributed to their better utilization of glycine-N and NH4+-N, respectively. .

A portable laser photoacoustic sensor based on a Field-Programmable Gate Array (FPGA) is reported for methane detection. A tunable DFB diode laser in the 1654 nm wavelength range is used as an excitation source. The photoacoustic signal processing was implemented by a FPGA device. A small resonant photoacoustic cell is designed. The minimum detection limit (1σ) of 10 ppm for methane (CH₄) is demonstrated.

A novel adaptive neural network-based fault-tolerant control scheme is proposed for six-degree freedom nonlinear helicopter dynamic. The proposed approach can detect and mitigate sensors' faults in real-time. An adaptive observer-based on neural network (NN) and extended Kalman filter (EKF) is designed, which incorporates the helicopter's dynamic model to detect faults in the navigation sensors. Based on the detected faults, an active fault-tolerant controller, including three loops of dynamic inversion, is designed to compensate for the occurred faults in real-time. The simulation results showed that the proposed approach is able to detect and mitigate different types of faults on the helicopter navigation sensors, and the helicopter tracks the desired trajectory without any interruption.

This paper presents the PEnsemble 4 model, a sophisticated machine learning framework that integrates IoT-based environmental data to accurately forecast maize yield. With the projected significant growth in global maize demand over the next decade, the inherent risks posed by the crop’s dependence on weather conditions necessitate improved prediction capabilities. The PEnsemble 4 model, developed with high accuracy, incorporates comprehensive datasets encompassing soil attributes, nutrient composition, weather conditions, and UAV-captured vegetation imagery. By employing a combination of Huber and M estimates, the PEnsemble 4 model effectively analyzes temporal patterns in vegetation indices, specifically CIre and NDRE, which serve as reliable indicators of canopy density and plant height. In addition, this research significantly contributes to precision agriculture by offering an efficient and sustainable alternative to conventional farming practices through precise yield predictions. Notably, the PEnsemble 4 model enables earlier estimation, advancing the timeline for yield prediction from the conventional day 100 in the R6 stage to day 79 in the R2 stage. This improvement enhances decision-making processes in farming operations. The remarkable accuracy rate of 91% underscores the importance of adopting a multifaceted data approach that harnesses IoT-derived environmental insights. Additionally, the PEnsemble 4 model extends its benefits beyond yield prediction, facilitating the detection of water and crop stress, as well as disease monitoring in broader agricultural contexts. Ultimately, the PEnsemble 4 model establishes a new standard in maize yield prediction, revolutionizing crop management and protection through the synergistic utilization of IoT and machine learning technologies.

(1) Background: The rapid expansion of 4G and 5G networks has raised public concerns about potential health risks associated with electromagnetic radiation. This study addresses these fears by investigating electromagnetic measurements in crowded squares, where human exposure is heightened. Despite rigorous scientific methodologies showing generally low levels of radiation from these technologies, public apprehension persists; (2) Methods: We conducted 496 measurements in Larissa's major squares, using a portable field strength analyzer and GIS mapping. Squares were categorized by traffic and population density; (3) Results: Low-traffic squares exhibited exposure ratios consistently below ICNIRP limits, with median values of 0.0012 and 0.00173 in non-active and active mobile phone cases, respectively. In high-traffic squares, the median exposure ratio was 0.00335 in non-active mobile phone cases, remaining below recommended limits; (4) Conclusions: These findings indicate no significant risk of electromagnetic radiation in crowded squares in Larissa, emphasizing the importance of factual communication and dispelling public misconceptions.

Existence of carcinogenic nitrite in food has attracted much attention, however, it is still a challenge to develop nitrite sensor with higher sensitivity and selectivity to enlarge its applications in daily life. Herein, one-dimensional honeycomb-like carbon nanofibers (HCNFs) were synthesized with an electrospun technology, and its specific structure enables the controlling growth and highly dispersed bismuth nanoparticles (Bi NPs) on its surface, which endows the obtained Bi/HCNFs with excellent electrocatalytic activity toward nitrite oxidation. By modifying Bi/HCNFs on screen-printed electrode, the constructed Bi/HCNFs electrode (Bi/HCNFs-SPE) can be used for nitrite detection in one drop of solution, and exhibits higher sensitivity (1269.9 μA mM-1 cm-2) in a wide range of 0.1~800 μM with lower detection limit (19 nM). Impressively, the Bi/HCNFs-SPE has been successfully used for nitrite detection in food and environment samples, the satisfactory property and recovery indicates its feasibility in further practical applications.

The experiences gathered during the past 30 years support the operational use of irrigation scheduling based on frequent multi-spectral image data. Currently, the operational use of dense time series of multispectral imagery at high spatial resolution makes monitoring of crop biophysical parameters feasible, capturing crop water use across the growing season, with suitable temporal and spatial resolutions. These achievements, and the availability of accurate forecasting of meteorological data, allow for precise predictions of crop water requirements with unprecedented spatial resolution. This information is greatly appreciated by the end users, i.e. professional farmers or decision-makers, and can be provided in an easy-to-use manner and in near-real-time by using the improvements achieved in web-GIS methodologies. This paper reviews the most operational and explored methods based on optical remote sensing for the assessment of crop water requirements, identifying strengths and weaknesses and proposing alternatives to advance towards full operational application of this methodology. In addition, we provide a general overview of the tools which facilitates co-creation and collaboration with stakeholders, paying special attention to these approaches based on web-GIS tools.

In this project, four of fibers Bragg gratings were fabricated by injecting different volumes of liquids (star line Glass Mechanix optical adhesive material, olive oil diluted with ethanol) into the hollow core fiber. The amplitude splitting interferometric technique with a high resolution specially designed translation stage was used for the fabrication process. The fabrication was done using ultraviolet laser operated at wavelength 405nm. The fabricated Bragg length of the four fibers is equal to 3.8 cm. The results presented fiber Bragg grating (FBG) with successful fabrication at 653.3 nm Bragg reflected wavelength.

Multi- and hyper-spectral, multi-angular top-of-canopy reflectance data call for an efficient retrieval system which can improve the retrieval of standard canopy parameters (as albedo, LAI, fAPAR), and exploit the information to retrieve additional parameters (e.g. leaf pigments). Furthermore consistency between the retrieved parameters and quantification of uncertainties are required for many applications. % (2) methods We present a retrieval system for canopy and sub-canopy parameters (OptiSAIL), which is based on a model comprising SAIL, PROSPECT-D (leaf properties), TARTES (snow properties), a soil model (BRDF, moisture), and a cloud contamination model. The inversion is gradient based and uses codes % created by Automatic Differentiation. The full per pixel covariance-matrix of the retrieved parameters is computed. For this demonstration, single observation data from the Sentinel-3 SY_2_SYN (synergy) product is used. The results are compared with the MODIS 4-day LAI/fPAR product and PhenoCam site photography. OptiSAIL produces generally consistent and credible results, at least matching the quality of the technically quite different MODIS product. For most of the sites, the PhenoCam images support the OptiSAIL retrievals. The system is computationally efficient with a rate of 150 pixel per second (7 millisecond per pixel) for a single thread on a current desktop CPU using observations on 26 bands. Not all of the model parameters are well determined in all situations. Significant correlations between the parameters are found, which can change sign and magnitude over time. OptiSAIL appears to meet the design goals, puts real-time processing with this kind of system into reach, seamlessly extends to hyper-spectral and multi-sensor retrievals, and promises to be a good platform for sensitivity studies. The incorporated cloud and snow detection adds to the robustness of the system.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Floods are among the most serious natural disasters worldwide; they cause enormous crop losses every year and threaten world food security. There are many studies focused on flood impact assessments for administrative districts but fewer on postdisaster impact assessments for specific crops. Therefore, this study used remote sensing data, including the normalized difference vegetation index (NDVI), elevation data, slope data, and rainfall data, combined with crop growing season data to construct a crop flood damage assessment index (CFAI). First, an analytic hierarchy process (AHP) was used to assign weights to the impact factors; then, the weighted composite score method was used to calculate the CFAI; and finally, the impact was classified as slight, moderate, or severe based on the magnitude of the CFAI . This method was used for the Missouri River floods of 2019 in the U.S. Due to the lack of measured data, the disaster vegetation damage index (DVDI) was used to validate the results. The combined approach achieved a high degree of consistency in spatial distribution. The CFAI can respond well to the degree of crop impact after flooding, providing new ideas and reference standards for agriculture-related departments.

This paper investigates an Energy Neutral System using Micro Energy Harvesters for a Health Monitoring Wireless Sensor Node (HM-WSN). We have implemented HM-WSN consisting of a solar cell energy harvester, a Power Management Unit (PMU) and the ucontroller, sensor and transmitter acting as load. A battery extender and a switching logic circuit for sensor node is designed to evaluate the efficiency of the proposed system. The HM-WSN senses body temperature with improvement in lifetime of coincell. The HM-WSN is built using commercially available off the shelf (COTS components and consumes 47.2uW for data being updated every 134s. It can be operated for approximately 1.32 years only on a coincell. Furthermore, the HM-WSN can be operated with solar energy at 200lux, achieving 96.36 years with a combination of a coincell with an additional capacitor of 2.2mF. It attains 4.07 years to 16.87 years lifetime with the load capacitor varying from 1mF to 1.5mF at 350lux lighting condition. With the same ambient condition and a 2mF load capacitor, HM-WSN attains complete energy autonomy.

The maintenance of traditional agricultural practices in protected small islands is closely linked to the preservation of the land, the protection of natural resources, and the conservation of local traditions. For this purpose, the Tuscan Archipelago National Park promoted the census of ancient horticultural varieties preserved by some farmers on the island of Elba. The survey revealed a deep-rooted historical, cultural, social, and economic link between this germplasm and the island’s territory. A scientific characterization of the landrace under ethnobotanical, morphological, and genetic aspects was carried out. Among these local varieties, two landraces of the Brassica species and three landraces of the Phaseolus species were identified and analyzed in this study. To ascertain their distinguishability and uniqueness, similar varieties were also identified based on morpho-physiological characteristics or territorial proximity and compared with the Elban landraces. Morpho-phenological data were collected, and molecular analyses were carried out using Simple Sequence Repeats (SSR) markers. Ten different SSR loci were considered for the Phaseolus species and nine for the Brassica species. The Tuscan Archipelago landraces showed a high level of internal variability but were clearly distinct from each other and from the analyzed varieties, as shown by AMOVA (Analysis of Molecular Variance). Their distinctness was further highlighted by the UPGMA dendrogram obtained from the genetic distance matrix. The same results were confirmed by Principal Coordinate Analysis (PCoA). This study confirms the peculiarity of the Elban landraces, their biodiversity is a heritage to be safeguarded, which can also be used in future breeding programs. These ancient Elban landraces were allocated to local farmers (most were young farmers) to protect them from extinction and to promote more resilient varieties cultivation compared to commercial hybrids widely spread in the area. Local farmhouses also play a strategic role in safeguarding the germplasm and dissemination of sustainable agricultural practices. There is high demand for ancient Elban landraces, this has led to the development of a new local economy balanced between agricultural tradition and innovation.

An active power dispatch method for a microgrid (MG) with multi-type loads, renewable energy sources (RESs) and distributed energy storage devices (DESDs) is the focus of this paper. The MG operates in a grid-connected model, and distributed power sources contribute to the service for load demands. The outputs of multiple DESDs are controlled to optimize the active power dispatch. Our goal with optimization is to reduce the economic cost under time-of-use (TOU) price, and to adjust the excessively high or low load rate of distributed transformers (DTs) caused by the peak-valley demand and load uncertainties. To simulate a practical environment, the stochastic characteristics of multi-type loads are formulated. The transition matrix of system state is provided. Then, a finite-horizon Markov decision process (FHMDP) model is established to describe the dispatch optimization problem. A learning-based technique is adopted to search the optimal joint control policy of multiple DESDs. Finally, simulation experiments are performed to validate the effectiveness of the proposed method, and the fuzzification analysis of the method is presented.

Stevia Rebaudiana Bertoni Morita II, a perennial plant native to Paraguay and Brazil, is also widely cultivated in the state of Colima, Mexico, for its use as a sweetener in food and beverages. The op-timization of soil parameters is crucial for maximizing biomass production and stevioside levels in stevia crops. This research presents the development and implementation of a monitoring system to track essential soil parameters, including pH, temperature, humidity, electrical conductivity, ni-trogen, phosphorus, and potassium. The system employs a wireless sensor network to collect qua-si-real-time data, which is transmitted and stored in a web-based platform. A Mamdani-type fuzzy logic model is utilized to process the collected data and provide to farmers an integrated assessment of soil quality. By comparing the quality data output of the fuzzy logic model with a line-ar-regression model, the system demonstrated acceptable performance, with a determination coef-ficient of 0.532 for random data and 0.906 for gathered measurements. The system enables farmers to gain insights into the soil quality of their stevia crops and empowers them to take preventive and corrective actions to improve the soil quality specifically for stevia crops.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The existence of low-cost and accurate tools that can equip the First Responders (FRs) to detect trapped victims and provide insights about their health condition in the aftermath of a disaster, is imperative. To address the problem of detecting trapped victims behind walls or debris, we have developed a tool that exploits an Ultra-Wide Band (UWB) radar sensor for data collection and Machine Learning (ML) algorithms for data analysis. To evaluate the efficacy of our approach, we collected data from nine humans, both in standing and lying down positions. Next, we applied various ML algorithms to the collected dataset for two discrete sub-tasks that are of interest from an FR’s perspective. The first task is the detection of the victim’s presence, where the algorithms attained more than 95% accuracy and F1-Score. The second task is the estimation of the distance between the radar sensor and the victim, where the tool showed an average error of less than 40 cm.

Germplasm is a long-term resource management mission and investment for civilization. For both food and nutritional health, the present changing environmental scenario has become an urgent universal concern. Multiple excellent studies have been previously performed, although the advancement and innovation of practices will require the exploration of the potentiality of crop germplasm. In this study, we emphasized (i) germplasm activates, current challenges and ongoing trends of the crop germplasm, and (ii) how the system biology will be helpful to understand the complex traits such as water use efficiency (WUE), and nitrogen use efficiency (NUE) to mitigate challenges for sustainable development under growing food requirement and climate change conditions. We focused on a vision for transforming PGR into a bio-digital resource system, for the development of climate-smart crops for sustainable food production. Moreover, this review attempted to address current challenges, research gaps and describe the advanced integrated strategies that could provide a platform for future crop improvement research.

Underwater Sensor Networks (UWSNs) can enable a broad range of applications such as resource monitoring, disaster prevention, and navigation-assisted. It is especially relevant for sensor nodes location in UWSNs. Global Positioning System (GPS) is not suitable for using in UWSNs because of the underwater propagation problems. Hence some localization algorithms based on the precise time synchronization between sensor nodes have been proposed which are not feasible for UWSNs. In this paper, we propose a localization algorithm called Two-Phase Time Synchronization-Free Localization Algorithm (TP-TSFLA). TP-TSFLA contains two phases, namely, range-based estimation phase and range-free evaluation phase. In the first phase, we address a time synchronization-free localization scheme base on the Particle Swarm Optimization (PSO) algorithm to decrease the localization error. In the second phase, we propose a Circle-based Range-Free Localization Algorithm (CRFLA) to locate the unlocalized sensor nodes which cannot obtain the location information through the first phase. In the second phase, sensor nodes which are localized in the first phase act as the new anchor nodes to help realize localization. Hence in this algorithm, we use a small number of mobile beacons to help achieve location without any other anchor nodes. Besides, to improve the precision of the range-free method, an extension of CRFLA by designing a coordinate adjustment scheme is updated. The simulation results show that TP-TSFLA can achieve a relative high localization ratio without time synchronization.

This paper proposes an innovative mechatronic piezo-actuated module to control vibrations in modern machine tools. Vibrations represent one of the main issues that compromise seriously the quality of the workpiece. The active vibration control (AVC) device is composed by a host part integrated with sensors and actuators synchronized by a regulator, able to make a self-assessment and adjust to the environmental alteration. This study presents the mechatronic model based on the kinematic and dynamic analysis of the AVC device. To ensure a real time performance, a H2-LQG controller has been developed and validated by simulations involving machine tool, PZT actuator and controller models. The Hardware-in-the-loop (HIL) architecture is adopted to control and attenuate the vibrations. A set of experimental tests has been performed to validate the AVC module on a commercial machine tool. The feasibility of the real time vibration damping is demonstrated and the simulation accuracy is evaluated.

Green manure could improve soil nutrients and crop production, playing a significant role in sustainable agriculture. However, the impacts of green manure on crop health and the roles soil microbial communities play in the process haven’t been clarified clearly yet. In this study, we investigated soil microbial community composition and structure in four tobacco farmlands, which were treated with different green manure (control, ryegrass, pea and rape), using 16S rRNA gene amplicons sequencing. Results showed that green manure had significant impacts on soil properties, microbial communities and tobacco health. First, soil total C, N and Ca content increased significantly in groups treated with green manure than control. Second, soil community diversity was significantly higher in groups treated with green manure. Third, green manure especially ryegrass, decreased tobacco disease (bacterial wilt) rate dramatically, and the process might be mediated by soil microbial communities. On the one hand, several microbial populations were found to be potentially disease inducible or suppressive. For example, the abundances of Dokdonella and Rhodanobacter were positively correlated to tobacco disease rate, while Acidobacteira_Gp4 and Gp6 had negative correlations with tobacco disease. On the other hand, soil microbial communities were shaped by soil properties (e.g., pH, C and N content). In conclusion, our research showed that green manure could increase soil nutrients directly, and further improve tobacco health mediated by soil microorganisms, which may shed light on revealing interactions among soil properties, microorganisms and plants.

In this paper, a method is developed for presenting a novel virtual torque sensor based on precise model and position measurements avoids the need of traditional strain gauges and amplifiers. More specifically, the harmonic drive compliance model and the Gaussian process regression (GPR) technique are used together to achieve virtual torque sensor measurement. While the harmonic drive compliance model provides the analytic part, the Gaussian process regression method is used to reconstruct the unmolded part based on motor-side and link-side joint angles as well as motor current. After an automatic offline calibration, the method allows for a lean online implementation. The virtual torque sensor measurement is compared with measurements of a commercial torque sensor, and the results have attested the effectiveness of the proposed method.

This study aimed at testing the effectiveness of novel combinations of chemical and physical methods to control Prosopis juliflora, an invasive weed in the Moshi and Simanjiro districts of Nothern Tan-zania. Six different treatments including manual uprooting, glyphosate, bark chop with chemical application, two separate chemical mixtures and control were tested in a total of 32 plots, which represented two land use types (grazing land and farmland) found in the two districts. Each plot covered 20m×30m plot area. Two response variables (stem count and tree volume) were recorded to compare weed population density before and after treatment six months later. An analysis of the untreated control plots, showed that the inherent growth potential of P. juliflora was higher in Moshi than in Simanjiro district. The number of stems increased during the experiment for all six treatments showing that the P. juliflora population had not yet reached the local carrying capacity. For the manual control treatment, the increase was reduced compared to the untreated control. For all other treatments, the increase in stem count was on par with that in the untreated control or even higher. Thus, we conclude that only manual uprooting had a controlling effect but not to the extent that it eradicated P. juliflora. Thus, it is for P. juliflora as for weed control in general: weed control must be an ongoing effort.

The state detection of power cable is very important to ensure the reliability of power supply. Traditional sensors are mostly based on electric field detection, the operation is complex, and its efficiency needs to be improved. This paper optimizes the design and development of the magnetic field detection sensor for AC power cables. Firstly, through the establishment of the magnetic field sensor model, it is determined that permalloy is the material of the magnetic core, the optimal aspect ratio of the magnetic core is 20, and the ratio of coil length to core length is 0.3. Secondly, the coil simulation model is established, and it is determined that the optimal number of turns of the coil is 11000 turns, the diameter of the enamelled copper wire is 0.08mm, and the equivalent magnetic field noise of the sensor is 0.06pT. Finally, the amplifying circuit based on negative magnetic flux feedback is designed and the sensor is assembled, and the experimental circuit is built for sensitivity test. the results show that the sensitivity of the magnetic field sensor is 327.6mV/μT. The sensor designed in this paper has the advantages of small size, high sensitivity, easy to carry and high reliability.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

Alternative fertilizations are essential to minimize the deteriorating effects of chemical fertilizers on soil and water quality/health. Accordingly, the present work investigated the effects of combined organic-inorganic fertilization (COIF) on wheat and rice yields, soil nutrients, and soil Cd accumulation. Hence, seven different treatments were set up: control (CK); conventional fertilization (CF); optimized fertilization (OF); organic fertilizer replacing 25% (T1) and 50% (T2) of OF; and organic nitrogen (N) replacing 25% (M1) and 50% (M2) of OF-N. Overall, significant increases occurred in the yields of COIF crops. Compared with the CF, the highest wheat and rice yields happened in M1 treatment (approximately by18.5%) (P < 0.05). COIF slightly alleviated soil acidification, and improved the cation exchange capacity (CEC) of the study soils. Besides, COIF treatments significantly increased the contents of total phosphorus, total potassium, available phosphorus, and available potassium by 6.35 to 16.9 %, 3.17 to 10.9 %, 5.53 to 28.7 %, and 2.6 to 12 %, respectively (P <0.05). Nevertheless, negligible increases took place in Cd content of COIF soils compared with the CK. Altogether, our results concluded on 25% replacement of OF-N by organic N (M1) to effectively improve the fertility/ecological sustainability of the study soils.

Human Activity Recognition (HAR) technology enables continuous behavior monitoring, particularly valuable in healthcare. This study investigates the viability of using an ear-worn motion sensor for classifying daily activities, including lying, sitting/standing, walking, ascending stairs, descending stairs, and running. Fifty healthy participants (between 20 and 47 years old) engaged in these activities while under monitoring. Various machine learning algorithms, ranging from interpretable shallow models to state-of-the-art deep learning approaches designed for HAR, were employed for classification. Results demonstrate the ear sensor's efficacy, with deep learning models achieving 98% accuracy rate of classification. The obtained classification models are agnostic regarding which ear the sensor is worn and robust against moderate variations in sensor orientation (e.g., due to differences in auricle anatomy), meaning no initial calibration of the sensor orientation is required. The study underscores the ear's efficacy as a suitable site for monitoring human daily activity and suggests its potential for combining HAR with in-ear vital signs monitoring. This approach offers a practical method for comprehensive health monitoring by integrating sensors in a single anatomical location. This integration facilitates individualized health assessments, with potential applications in tele-monitoring, personalized health insights, and optimizing athletic training regimes.

We report the relative humidity (R.H.) sensing response of a resistive sensor, employing sensing layers based on a ternary nanohybrid comprising holey carbon nanohorns (CNHox), potassium chloride (KCl), and polyvinylpyrrolidone (PVP) at mass ratios 7/1/2, 6.5/1.5/2, and 6/2/2 (w/w/w/w). The sensing structure comprises a silicon substrate, a SiO2 layer, and interdigitated transducer (IDT) electrodes. The sensing film is deposited on the sensing structure via the drop-casting method. The sensing layers' morphology and composition are investigated through Scanning Electron Microscopy (S.E.M.) and RAMAN spectroscopy. The ternary hybrid-based thin film resistance increases when the sensors are exposed to R.H., ranging from 0% to 100%. The manufactured devices show a room temperature response comparable to a commercial capacitive R.H. sensor and are characterized by excellent linearity, rapid response time, and good sensitivity. The presented sensors exhibit superior performance in terms of sensitivity compared to other similarly manufactured and tested sensors that employ a CNHox-based sensing layer. We explain the sensing role of each constituent of the ternary hybrid nanocomposites based on their chemical and physical properties, electronic properties, and affinity for water molecules. Different alternative sensing mechanisms are considered and discussed, such as the decreasing number of holes in the holey CNHox at the interaction with water molecules, proton conduction, and PVP swelling.

The pharmacological effects of the fruiting body of Ophiocordyceps sinensis (Os) exerted antioxidant, anti-virus, and immunomodulatory, whereas the anti-inflammatory effects and active components of Os mycelial submerged culture (OMSC) are not known. This study aimed to investigate the active compounds in the fermented liquid (FLOS), hot water (WEOS), and 50-95% (EEOS-50, EEOS-95) ethanol extracts of OMSC and their anti-inflammatory effects and potential mechanisms in LPS-stimulated microglial BV2 cells. The results demonstrated that all of the OMSC extracts could inhibit NO production in BV2 cells. EEOS-95 exhibited the strongest inhibitory effects (41 % inhibitory ability at 500 µg/mL), and its ergosterol, GABA, total phenolic, and total flavonoid contents were significantly higher than those of the other extracts (18.60, 18.60, 2.28, and 2.14 mg/g, p < 0.05, respectively). EEOS-95 also has a strong inhibitory ability against IL-6, IL-1β and TNF-α with IC50 of 617, 277 and 507 µg/mL, respectively, which is higher than that of 1 mM melatonin. The anti-inflammatory mechanism of EEOS-95 seems to be associated with up-regulation of PPAR-γ/Nrf-2/HO-1 antioxidant-related expression and down-regulation of NF-κB/COX-2/iNOS pro-inflammatory expression signaling. Therefore, we hypothesized that EEOS-95 can prevent neurodegenerative diseases, but the effect on the application in vivo should be further investigated.

The importance of irrigation in boosting agricultural production and productivity is widely understood. Proper planning and effective and efficient management and operation of irrigation system require crop and site-specific data. Since the last few years, Ethiopia has embarked on expansion of irrigated wheat. However, crop-specific data useful for irrigation planning and management for wheat crop is limited. The objective of this research was to determine water requirements and crop coefficients for wheat crops based on field measurements. The research was carried out at the Debre Zeit Agricultural Research Center in central Ethiopia during the dry season (Bega) of 2021/22. The crop considered for the experiment was durum wheat of the Utuba variety. Two non-weighing lysimeter units were employed to measure the water balance components. The soil moisture was monitored using gravimetric method on daily basis conducted both before and after each irrigation event at various depth intervals. The crop required a total of 115 days to fully mature. The length of the growth of initial, development, mid, and late stages were about 20, 30, 42, and 23 days, respectively. Microsoft Excel was used for the data analysis and the CropWAT8.0 model to estimate the reference evapotranspiration. Crop evapotranspiration (ETc) was determined using the water balance equation, and crop coefficients were computed from ETc and reference evapotranspiration (ETo). The results indicate that the total seasonal water requirement of the crop was 392.75mm. The growth stage-based water requirement was 40.35 mm, 82.44 mm, 238.66 mm, and 31.3 mm during the initial, development, mid, and late growing stages, respectively. For the initial, development, mid, and late stages of wheat growth, the crop coefficient was calculated to be 0.51, 0.83, 1.29, and 0.52, respectively. It was found that a fourth-degree polynomial equation fits well and explains the relationship between day of growth stage and kc of the crop. Although a one-season measurement, the results generated here could be useful for crop-specific data in scarce areas.

In contemporary construction, the prevalence of vibration serviceability issues in lightweight and slender structures has become increasingly common, owing to advancements in building materials and construction methods. While these structures often meet the criteria for ultimate limit states, they can still elicit complaints due to excessive vibrations induced by human activity. To address this challenge, the Integral Resonant Control (IRC) technique has emerged as a favored approach for actively damping vibrations in various systems. This study introduces a fresh perspective on implementing a multi-input multi-output (MIMO) IRC scheme for active vibration control (AVC) specifically tailored for pedestrian structures utilizing inertial mass actuators. Building upon a common framework and design methodology outlined in previous research, this work presents a novel application of MIMO IRC for AVC. The designed controller is rigorously tested and implemented on a laboratory floor structure to validate its efficacy.

In California, water is a perennial concern. As competition for water resources increases due to growth in population, California’s tree nut farmers are committed to improving the efficiency of water used for food production. There is an imminent need to have reliable methods that provide information about the temporal and spatial variability of crop water requirements, which allow farmers to make irrigation decisions at field scale. This study focuses on estimating the actual evapotranspiration and crop coefficients of an almond and pistachio orchard located in Central Valley (California) during an entire growing season by combining a simple crop evapotranspiration model with remote sensing data. A dataset of the vegetation index NDVI derived from Landsat-8 was used to facilitate the estimation of the basal crop coefficient (Kcb), or potential crop water use. The soil water evaporation coefficient (Ke) was measured from microlysimeters. The water stress coefficient (Ks) was derived from airborne remotely sensed canopy thermal-based methods, using seasonal regressions between the crop water stress index (CWSI) and stem water potential (Ystem). These regressions were statistically-significant for both crops, indicating clear seasonal differences in pistachios, but not in almonds. In almonds, the estimated maximum Kcb values ranged between 1.05 to 0.90, while for pistachios, it ranged between 0.89 to 0.80. The model indicated a difference of 97 mm in transpiration over the season between both crops. Soil evaporation accounted for an average of 16% and 13% of the total actual evapotranspiration for almonds and pistachios, respectively. Verification of the model-based daily crop evapotranspiration estimates was done using eddy-covariance and surface renewal data collected in the same orchards, yielding an r² >= 0.7 and average root mean square errors (RMSE) of 0.74 and 0.91 mm day^-1 for almond and pistachio, respectively. It is concluded that the combination of crop evapotranspiration models with remotely-sensed data is helpful for upscaling irrigation information from plant to field scale and thus may be used by farmers for making day-to-day irrigation management decisions.

An easy to implement and cost-effective Fiber Bragg Grating (FBG) sensor interrogation technique based on a ring Erbium-Doped Fiber Laser (EDFL) topology is proposed and experimentally assessed. The FBG sensor is part of the EDFL cavity and must have a central wavelength located within the linear region of the EDF’s amplified spontaneous emission (ASE) spectrum which occurs between 1530 and 1540nm. In this manner, the wavelength-encoded response of the FBG under strain is converted to a linear variation of the laser output power, removing the need for spectrum analysis as well as any limitations from the use of external edge-filtering components. In addition, the laser linewidth is significantly reduced with respect to the FBG bandwidth thus improving the resolution of the system, whereas its sensitivity can be controlled through the pumping power. The performance of the system has been characterized by modeling and experiments for EDF's with different lengths, doping concentrations and pumping power levels. The influence of mode-hopping in the laser cavity on the resolution and accuracy of the system has also been investigated.

Forest canopy structure (CS) controls many ecosystem functions and is highly variable across landscapes, but the magnitude and scale of this variation is not well understood. We used a portable canopy lidar system to characterize variation in five categories of CS along N = 3 transects (140–800 m long) at each of six forested landscapes within the eastern USA. The cumulative coefficient of variation was calculated for subsegments of each transect to determine the point of stability for individual CS metrics. We then quantified the scale at which CS is autocorrelated using Moran’s I in an Incremental Autocorrelation analysis. All CS metrics reached stable values within 300 m but varied substantially within and among forested landscapes. A stable point of 300 m for CS metrics corresponds with the spatial extent that many ecosystem functions are measured and modeled. Additionally, CS metrics were spatially autocorrelated at 40 to 88 m, suggesting that patch scale disturbance or environmental factors drive these patterns. Our study shows CS is heterogeneous across temperate forest landscapes at the scale of 10’s of meters, requiring a resolution of this size for upscaling CS with remote sensing to large spatial scales.

Rice canopy height and density are directly usable crop phenotypic traits for the direct estimation of crop biomass. Therefore, it is crucial to rapidly and accurately estimate rice canopy phenotypic parameters. To achieve non-destructive detection and estimation of essential phenotypic parameters in rice, a platform based on LiDAR point cloud data for rice phenotypic parameter detection was established. Data collection of rice canopy layers was performed across multiple plots. The LiDAR-detected canopy top point clouds were selected using a method based on the highest percentile, and the rice canopy surface model was calculated. Canopy height estimation was the difference between ground elevation and percentile value. To determine the optimal percentile defining the rice canopy top, testing was conducted incrementally from 0.8 to 1 with an increment of 0.005. The optimal percentile value was found to be 0.975. The root mean square error (RMSE) between LiDAR-detected canopy height and manually measured canopy height was calculated. The prediction model based on canopy height (R2=0.941, RMSE=0.019) exhibited a strong correlation with actual canopy height. Linear regression analysis was conducted between gap fraction of different plots and manually detected average Leaf Area Index (LAI) of rice canopy. Prediction models for canopy LAI based on ground return counts (R2=0.24, RMSE=0.1) and ground return intensity (R2=0.28, RMSE=0.09) showed strong correlations but had lower correlation with rice canopy LAI. Regression analysis was performed between LiDAR-detected canopy height and manually measured rice canopy LAI. The results indicated that the prediction model based on canopy height (R2=0.77, RMSE=0.03) was more accurate.

Subsoil tillage loosens compacted soil for better plant growth, but promotes water loss, which is a concern in areas commonly irrigated. Therefore, our objective was to determine the physiological responses of high yield spring corn (Zea mays L.) to Subsoil tillage depth when grown in the western plain irrigation area of Inner Mongolia that leads to the best water use efficiency. The experiment during 2014 and 2015 used Zhengdan958 and Xianyu335 with three differing subsoil tillage depths (30, 40, or 50 cm) as trial factor and shallow rotary as a control. Subsoil tillage increased shoot dry matter accumulation, leading to a greater shoot/root ratio. Subsoil tillage helped retain greater leaf area index in each growth stage, increase the leaf area duration, net assimilation rate, and relative growth rate, with greater effects as tillage was deeper, effectively delaying the aging of the blade. Grain yields were increased by 0.7%–8.9% on average in subsoil tillage treatments compared to conventional soil treatment shallow rotary, Water use efficiency were increased by 1.93%–18.49% on average in subsoil tillage treatment compared to shallow rotary, resulting in net income increases by 2.24% to 6.97% compared to shallow rotary. Among the three different subsoil tillage depth treatment, the grain yield, water use efficiency, and net income is the best under the treatment of subsoil tillage depth of 50 cm.

Hyperspectral images are an important tool to assess ecosystem biodiversity both on terrestrial and benthic habitats. To obtain more precise analysis of biodiversity indicators that agree with indicators obtained using field data, analysis of spectral diversity calculated from images have to be validated with field based diversity estimates. The plant species richness is one of the most important indicators of biodiversity. This indicator can be measured in hyperspectral images considering the Spectral Variation Hypothesis (SVH) which states that the spectral heterogeneity is related to spatial heterogeneity and thus to species richness. The goal of this research is to capture spectral heterogeneity from hyperspectral images for a terrestrial neo tropical forest site using Vector Quantization (VQ) method and then use the result for prediction of plant species richness. The results are compared with that of Hierarchical Agglomerative Clustering (HAC). The validation of the process index is done calculating the Pearson correlation coefficient between the Shannon entropy from actual field data and the Shannon entropy computed in the images. Terrestrial dry forest and marine coastal hyperspectral images with different resolutions have been used for spectral diversity feature validation.

A reliable and efficient rail track defect detection system is essential for maintaining rail track integrity and avoiding safety hazards and financial losses. Eddy current (EC) testing is a non-destructive technique that can be employed for this purpose. The trade-off between spatial resolution and lift-off should be carefully considered in practical applications to distinguish closely spaced cracks such as those caused by rolling contact fatigue (RCF). A multi-channel eddy current sensor array has been developed to detect defects on rails. Based on the sensor scanning data, defect reconstruction along the rails is achieved using an inverse algorithm that includes both direct and iterative approaches. In experimental evaluations, the EC system with the developed sensor is used to measure defects on a standard test piece of rail with a probe lift-off of 4-6 mm. The reconstruction results clearly reveal cracks at various depths and spacings on the test piece.

The application of artificial intelligence to point-of-care testing (POCT) disease detection has become a hot research field, in which breath detection which detects the patient's exhaled VOCs combined with sensor arrays of Convolutional Neural Network (CNN) algorithms as a new lung cancer detection is attracting more researchers' attention. However, due to low accuracy, high complexity computation and large number of parameters make the CNN algorithms difficult transplant to the embedded system of POCT devices. A lightweight neural network (LTNet) in this work is proposed to deal with this problem, and meanwhile, achieve high-precision classification of acetone and ethanol gases, which are respiratory markers for lung cancer patients. Compared to currently popular lightweight CNN models such as EfficientNet, LTNet has fewer parameters (32K) and its training weight size is only 0.155 MB. LTNet achieved an overall classification accuracy of 99.06% and 99.14% in the own mixed gas dataset and the University of California (UCI) dataset, which are both higher than that of the five existing models’, and it also offers the shortest training (844.38s and 584.67s) and inference time (23s and 14s) in the same validation set. Compared to the existing CNN models, LTNet is more suitable for resource-limited POCT devices.

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

The importance of conflict analysis and safety considerations during work zone intervals at signalized intersections cannot be overstated, as these periods pose unique challenges and safety risks for both motorists and pedestrians. Work zones introduce temporary changes to traffic patterns, lane configurations, and signal timings, which can disrupt the flow of traffic and increase the likelihood of conflicts between vehicles and pedestrians. By conducting comprehensive conflict analysis, it is possible to identify potential conflict points, such as merging areas, pedestrian crossings, and lane transitions, and implement targeted safety measures to mitigate risks. Additionally, considering safety considerations during work zone intervals is paramount to safeguarding the well-being of road users and minimizing the occurrence of conflicts or collisions. Measures such as enhanced signage, temporary traffic control devices, and increased enforcement efforts can help promote compliance with traffic regulations and ensure the safe passage of vehicles and pedestrians through work zones. This study investigates the dynamics of traffic behavior and safety implications within work zones at signalized intersections, aiming to address key challenges and enhance intersection management strategies. Through comprehensive analysis, varying frequencies of Vehicle-to-Vehicle (V2V) conflicts were observed across different movement directions, with significant occurrences identified in specific phases of the traffic signal cycle. Specifically, 69 V2V conflicts in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8 were recorded. Furthermore, the examination of Vehicle-to-Pedestrian (V2P) conflicts underscored the importance of prioritizing pedestrian safety, with notable occurrences observed in phases associated with pedestrian crossing movements. Meanwhile, despite the closure of left-turn movements, instances of red light running persisted, with 69 red light running events in phase #1, 181 in phase #2, 31 in phase #3, 207 in phase #4, 1 in phase #5, 274 in phase #6, 93 in phase #7, and 186 in phase #8.To mitigate these safety concerns during work zone intervals, proactive measures are essential. Strategies include improving communication through clear signage and advanced warning systems, enhancing enforcement efforts with red light cameras and increased police presence, and investing in infrastructure improvements such as temporary pedestrian facilities. Integration of real-time data from sensors, particularly LiDAR technology, offers significant advantages in detecting conflicts and red light runners during work zone intervals. LiDAR's precise, real-time data on vehicle and pedestrian movements, combined with its 360-degree coverage and high spatial resolution, facilitates accurate detection and tracking of potential conflict scenarios, contributing to enhanced intersection safety and traffic management efficiency. This study endeavored to conduct a traffic safety analysis during work zone intervals at a signalized intersection in Baltimore City, known for its high rate of traffic crashes, utilizing LiDAR sensor technology.

The objective of this study was to carry out the extraction and characterization of chitin and chitosan from the exoskeletons of the Farfantepenaeus californiensis species of shrimp, as well as its application in the formulation of polymeric films plasticized with glycerol used in the process of food packaging. The characterization of the extracted polymer was made by Fourier transform infrared spectroscopy (FTIR), Scanning electron microscopy (SEM), and physicochemical analysis of chitin and chitosan, resulting in a theoretical performance of 29.33% and 16.46%, respectively. In terms of quality, it was determined that the extracted chitosan had a molecular weight of 1.10 x105 g/mol and a deacetylation degree of 80.23%, which classifies it as a low-molecular weight chitosan, suitable for food packaging. It was shown that the extracted chitosan is fit for the production of the films by using the casting method, presenting a tension resistance of 1 MPa. The Antibacterial analysis was carried out using Staphylococcus aureus (S. aureus) and Escherichia coli (E. coli), bacterial models commonly found in food. The results showed an effective inhibition capability of the polymeric materials. Overall, the results for both chitosan and the films indicate a high potential for application in the food packaging sector.

This paper presents a two-stage ADC based on pseudo-differential operational transconductance amplifier (OTA), which is designed for the readout circuit of X-ray linear array sensor. This hybrid ADC employs an incremental sigma-delta ADC and a cyclic ADC, achieving a good trade-off between accuracy and conversion speed. The two stages share the same hardware to reduce power consumption and die area. A common-mood feedback module is used to suppress the influence of charge injection, and the effectiveness is demonstrated by detailed theoretical analysis. A test chip of 14-bit ADC is fabricated in 0.35μm CMOS technology. The measured root mean square (RMS) value of DNL is 0.254 LSB, and the maximum value of INL is -0.776/+1.56 LSB. The measured effective number of bits (ENOB) is 13.43 bits.

This paper focuses on optimal sensor positioning for monitoring activities of daily living and investigates different combinations of features and models on different sensor positions, i.e., the side of the waist, front of the waist, chest, thigh, head, upper arm, wrist, and ankle. Sixteen features are extracted and the feature importance is measured by using the Relief-F feature selection algorithm. Eight classification algorithms are evaluated on a dataset collected from young subjects and that collected from elderly subjects, with two different experimental settings. To deal with different sampling rates, signals with a high data rate are down-sampled and a transformation matrix is used for aligning signals to the same coordinate system. The thigh, chest, side of the waist, and front of the waist are the best four sensor positions for the first dataset (young subjects), with average accuracy values being greater than 95%. The best model obtained from the first dataset for the side of the waist is validated on the second dataset (elderly subjects). The most appropriate number of features for each sensor position is reported. The results provide a reference for building activity recognition models for different sensor positions, as well as for data acquired from different hardware platforms and subject groups.

Development and redevelopment are important drivers of tree removal and canopy loss in urban landscapes. Local ordinances are often used to curtail tree removal, but punitive regulations alone may not be enough to reduce urban tree canopy loss in land development. In Florida (US), efforts to balance trees and development have so far focused on fees and fines, but with a recent backlash against tree regulations and the fast pace of urban growth, we explored the possible role of incentives in urban tree policies. We interviewed 20 land developers across Florida to understand their perspectives on current barriers and potential incentives for tree preservation and planting. We collected data from developers, whose perspectives on tree preservation are often unknown or overlooked, despite their significant role in tree planting, removal, and retention in and around cities. Our results show that major barriers to tree preservation and planting include requirements to grade sites for stormwater management, site constraints, and monetary costs. Most developers did not know of any existing incentives beyond intrinsic motivations but said that financial incentives would be most appealing to them. Top incentive suggestions include increasing building density, reducing impact fees and tax liability, and changing tree mitigation policies. Another promising finding is that developers are willing to work with regulators to find solutions that benefit both parties. Future research should consider evaluating the level of support and viability of different incentives by gathering feedback from policymakers, land developers, and the public.

Climate change related increases in frequency and intensity of heatwaves affect viticulture, leading to losses in yield and grape quality. We assessed whether canopy architecture manipulation mitigates the effects of summer stress in a Mediterranean vineyard. Muscat of Alexandria grapevines were monitored during 2019-2020. Two canopy shoot positioning treatments were applied: Vertical shoot positioning (VSP); and Modulated shoot positioning (MSP), the west side upper foliage released to promote partial shoot leaning, shading the clusters. Clusters were sampled at pea size (PS), veraison (VER) and full maturation (FM). Measurements included rachis anatomy and hydraulic conductance, and aquaporins (AQP) and stress-related genes expression in cluster tissues. Results show significant seasonal and interannual differences in Kh and vascular anatomy. At VER, Krachis , Krachis+pedicels, and xylem diameter decreased but were unaffected by treatments. The Phloem/Xylem ratio was either increased (2019) or reduced (2020) in MSP, compared to VSP. Most AQP were down-regulated at FM in pedicels, and up-regulated at VER in pulp. A potential maturation shift in MSP was observed, confirmed by the up-regulation of several stress-related genes in all tissues. The study pinpoints the role of canopy architecture in berry water relations and stress response during ripening.

Leaf temperature (T_leaf) influences photosynthesis and respiration. Currently, there is a growing interest on including lianas in productivity models due to their increasing abundance, and their detrimental effects on net primary productivity in tropical environments. Therefore, understanding the differences of T_leaf between lianas and trees is important for future of forest on whole ecosystem productivity. Here we determined the displayed leaf temperature (T_d= T_leaf – ambient temperature) of several species of lianas and their host trees during ENSO and non-ENSO years to evaluate if the presence of lianas affects the T_d of their host trees, and if leaves of lianas and their host trees exhibit differences in T_d. Our results suggest that close to midday, the presence of lianas does not affect the T_d of their host trees; however, lianas tend to have higher values of T_d than their hosts across seasons, in both ENSO and non-ENSO years. Although lianas and trees tend to have similar physiological-temperature responses, differences in T_d could lead to significant differences in rates of photosynthesis and respiration based temperature response curves. Future models should thus consider differences in leaf temperature between these life forms to achieve robust predictions of productivity.

Huperzine A is an herbal reversible inhibitor of Acetylcholinesterase (AChE). A molecular docking analysis on Huperzine A molecule has been carried out to understand its structure, conformational flexibility, intermolecular interaction and the binding affinity in the active site of AChE enzyme. Further, the charge density distribution of huperzine A molecule (lifted from the active site of AChE) was determined from the high level quantum chemical calculations coupled with charge density analysis. The binding affinity of Huperzine A towards AChE was calculated from the molecular docking; the lowest docked energy is -8.46 kcal/mol. In the active site, huperzine A molecule interacts with acyl binding pocket-Phe330 of AChE, that is, the bicyclo ring group of huperzine A forms an intermolecular interaction with the oxygen atom of main chain of the amino acid residue Phe330 at the distances 3.02 and 3.25 Å respectively. On the other hand, a gas phase study on huperzine A molecule also performed using HF and DFT (B3LYP) methods with the basis set 6-311G**. The molecular structure, conformation, and the charge density distribution of huperzine A molecule in the gas phase have determined using quantum chemical calculations and the charge density analysis. The comparative studies between the gas phase and the active site forms of huperzine A molecule, explicitly reveals the degree of conformational modification and the charge density redistribution of huperzine A when present in the active site. The dipole moment of the molecule in the active site is 6.85 D, which is slightly higher than its gas phase value (5.91 D). The electrostatic potential (ESP) surface of active site molecule clearly shows the strong electronegative and positive ESP regions of the molecule, which are the expected strong reactive locations of the molecule.

Obesity is related to the establishment of chronic inflammation and metabolic diseases, but it can be positively influenced by the regular practice of physical activity. The study aimed to compare the anthropometric, metabolic, and inflammatory parameters of physically active Military Police Officers (MPOs) with those who are less physically active. Sixty male MPOs, low activity (n=28) and physically active (n=32) participated. The following parameters were measured: plasma cytokine levels, C-reactive protein (CRP) levels, circulating glucose triglyceride (TAG) and high-density lipoprotein cholesterol (HDL-C) levels, and plasma glutamic oxalacetate transaminase (GOT), glutamic-pyruvate transaminase (GPT), and gamma-glutamyl transferase (GGT) activities. The physically active group presented lower body fat and reduced TAG and IL-8 levels compared to the low activity group. Moreover, a negative correlation between SPE and SBP, DBP, BPM was detected for the physically active group (p<0.05) but not in the low activity group. Furthermore, the physically active group's work time (WT) values were not correlated with the important metabolic markers SBP, DBP, BPM, GLU, TAG (p>0.05) but could be in the low activity group (p<0.05). These findings highlight the fundamental protective role of physical activity in controlling body composition, subclinical inflammation, and cardiovascular risk in MPOs.

In the context of improving aircraft safety, this study focuses on the development and evaluation of a graphene-based ice detection system using an environmental chamber. The research is driven by the need for more accurate and efficient ice detection methods, crucial in mitigating in-flight icing hazards. The methodology employed involves testing flat graphene-based sensors in a controlled environment, simulating a variety of climatic conditions that could be experienced in an aircraft during its entire flight. The environmental chamber enabled precise manipulation of temperature and humidity levels, thereby providing a realistic and comprehensive test bed for sensor performance evaluation. The results were significant, revealing the graphene sensors’ heightened sensitivity and rapid response to the subtle changes in environmental conditions, especially the critical phase transition from water to ice. This sensitivity is the key to detecting ice formation at its onset, a critical requirement for aviation safety. The study concludes that graphene-based sensors, tested under varied and controlled atmospheric conditions, exhibit a remarkable potential in enhancing ice detection systems for aircraft. Their lightweight, efficient and highly responsive nature makes them a superior alternative to traditional ice detection technologies, paving the way for more advanced and reliable aircraft safety solutions.

Wireless Powered Communication Networks (WPCN), which has attracted much attention of researchers, also been recently recommended in 5^th generation (5G) wireless networks. With the help of the WPCN, the reliability and battery life of wireless low-power devices can be improved. In this paper, we investigate throughput and ergodic capacity in WPCN-assisted amplify-and-forward (AF) relaying system, considering two transmission modes including delay-tolerant and delay-limited. As important achievement, we propose symmetric energy harvesting protocol, namely time power switching relaying (TPSR) in order to find maximal throughput. In particular, both time switching and power switching coefficients in this schemes are considered. Unlike most of the previous works, we further focus on impact of outdated channel state information (CSI) in this WPCN. In order to evaluate information processing efficiency, the performance can be substantially improved by optimally harvesting time and power coefficients of the received signal at relay node for energy and information extraction, and by deploying several scenarios. By deploying Monte Carlo simulation, it is confirmed that the system performance is more sensitive to CSI estimation error, noise variance, signal-to-noise ratio (SNR) and resulting in other reasonable computations of TPSR need be deployed to obtain QoS requirement.

Open source software such as OpenDSS has given a lot of help to distribution network researchers and educators. With high penetration of distributed renewable energy resources into distribution network, tradition distribution steady state analysis software such as OpenDSS is faced with difficulty in handling distributed generators. Three-phase distributed generators are often modeled in sequence frame while unbalanced distribution network are usually modeled in phase frame. So a load flow in sequence-phase coupled frame is proposed to handle models described in both frames. Voltage controlled DGs which are difficult to cope with in OpenDSS are handled in proposed program. The steady state analysis platform is programmed with open source Modelica language and the main aim of this paper is to introduce an open source platform for active distribution network steady analysis include load flow and short circuit analysis which can be easily adopted and improved by other educators and researchers.

During public health events, Active Mobility (walking and cycling) plays an important role in securing residents' travel. To enhance the resilience of urban transportation, this article integrates the travel environment elements for walking and cycling and constructs a travel environment for Active Mobility evaluation index system. This article uses survey data from the main urban area of Harbin in the context of the COVID-19 pandemic in May 2022, and combines the Gradient Boosting Decision Tree (GBDT) and Impact-Asymmetry Analysis (IAA) methods to analyze the satisfaction of the travel environment for Active Mobility. It proposes strategies for optimizing the travel environment for Active Mobility, ensuring residents' travel during public health events, guiding them to adopt Active Mobility, and improving urban transportation resilience. This research shows that Active Mobility can enhance urban transportation resilience. In addition, there are differences in resident demand for walking and cycling environments in the travel environment for Active Mobility. Residents are more concerned about the comfort of the walking environment, while they prioritize the convenience of the cycling environment.

RNAi technology is a versatile, effective, safe, and eco-friendly alternative for crop protection. There is plenty of evidence of its use through host-induced gene silencing (HIGS) and spray-induced gene silencing (SIGS) techniques to control viruses, bacteria, fungi, insects, and nematodes. For SIGS, its most significant challenge is achieving stability and avoiding premature degradation of RNAi in the environment or during its absorption by the target organism. One alternative is encapsulation in liposomes, virus-like particles, polyplex nanoparticles, and bioclay, which can be obtained through the recombinant production of RNAi in vectors, transgenesis, and micro/nanoencapsulation. The materials must be safe, biodegradable, and stable in multiple chemical environments, favoring the controlled release of RNAi. Most of the current research on encapsulated RNAi focuses primarily on oral delivery to control insects by silencing essential genes. The regulation of RNAi technology focuses on risk assessment using different approaches; however, this technology has positive economic, environmental, and human health implications for its use in agriculture. The emergence of alternatives combining RNAi gene silencing with the induction of resistance in crops by elicitation and metabolic control is expected, as well as multiple silencing and biotechnological optimization of its large-scale production.

Nitrogen (N) is an essential macro nutrient for crop growth; therefore, N deficit can greatly limit crop growth and production. In the North China Plain (NCP), winter wheat is one of the main food crops, and its yield has increased from approximately 4000 kg ha-1 to 6000 kg ha-1 in the last two decades. Determining the proper N application rates at different growth stages and in all seasons is very important for the sustainable and high production of wheat in the NCP. A field experiment with five N application rates (250, 200, 150, 100, and 40 kgN·ha-1, designated as N250, N200, N150, N100, and N40, respectively) was conducted during the 2017-2018 and 2018-2019 winter wheat seasons to investigate the effects of the N application rate on water- and fertiliz-er-utilization efficiency, and on the crop growth and yield of winter wheat under sprinkler fer-tigation conditions. The results showed that, in the N application range of 40-200 kg ha-1, crop yield and water- and fertilizer-use efficiencies increased as the N application rate increased; however, further increases in the N application rate did not have additional benefits. The N up-take after regreening of winter wheat linearly increased with crop growth. Considering the wheat yield and N-use efficiency, the optimal N application range was 200 kg ha-1, and the best top-dressing strategy was equal amounts of N applied at the regreening, jointing, and grain-filling stages. The results of this study will be useful for optimizing field N management to achieve high wheat yield production in the NCP and in regions with similar climatic and soil environment conditions.

The market for autonomous vehicles (AV) is expected to experience significant growth over the coming decades and to revolutionize the future of transportation and mobility. The AV is a vehicle that is capable of perceiving its environment and perform driving tasks safely and efficiently with little or no human intervention and is anticipated to eventually replace conventional vehicles. Self-driving vehicles employ various sensors to sense and perceive their surroundings and, also rely on advances in 5G communication technology to achieve this objective. Sensors are fundamental to the perception of surroundings and the development of sensor technologies associated with AVs has advanced at a significant pace in recent years. Despite remarkable advancements, sensors can still fail to operate as required, due to for example, hardware defects, noise and environment conditions. Hence, it is not desirable to rely on a single sensor for any autonomous driving task. The practical approaches shown in recent research is to incorporate multiple, complementary sensors to overcome the shortcomings of individual sensors operating independently. This article reviews the technical performance and capabilities of sensors applicable to autonomous vehicles, mainly focusing on vision cameras, LiDAR and Radar sensors. The review also considers the compatibility of sensors with various software systems enabling the multi-sensor fusion approach for obstacle detection. This review article concludes by highlighting some of the challenges and possible future research directions.

Maize is an important staple food crop in sub-Saharan Africa (SSA). However, the average grain yield on farmers’ fields falls considerably short of the demand of the region’s population. In addition, the normal endosperm maize widely consumed in SSA is deficient in vitamin A. Drought, a consequence of climate change, is a major constraint to maize production, resulting in seasonal low grain yield in farmers’ fields. The objectives of this study were to assess the performance of newly developed extra-early maturing provitamin A hybrids under managed drought and well-watered conditions, compare the outcomes of multiple trait base-index and multi-trait genotype-ideotype distance index selection procedures, and identify drought-tolerant hybrids with stable performance across contrasting environments for commercialization in SSA. One hundred and ninety provitamin A hybrids and six checks were evaluated under managed drought and well-watered conditions at Ikenne for two seasons between 2021 and 2023. A 14*14-lattice design was used for the field evaluations under both research conditions. Drought stress was achieved by the complete withdrawal of irrigation water 25 days after planting. Results revealed significant differences among the hybrids under drought and well-watered conditions. Grain yield, ears per plant, and plant aspect under managed drought were correlated to the same traits under well-watered conditions suggesting that the expression of these traits is governed by common genetic factors. Twenty-nine hybrids were identified as top-performing drought-tolerant hybrids by the multiple trait base index and multiple-trait genotype–ideotype distance index. Of the selected outstanding 29 hybrids, 34% were derived from crosses involving the tester TZEEIOR 197, demonstrating the outstanding genetic potential of this inbred line. Further analysis of the 29 selected hybrids revealed TZEEIOR 509 × TZEEIOR 197 as the hybrid that combined the most drought-tolerant adaptive traits. However, the hybrids TZEEIOR 526 × TZEEIOR 97, TZEEIOR 384 × TZEEIOR 30, TZEEIOR 515 × TZEEIOR 249, TZEEIOR 510 × TZEEIOR 197, TZEEIOR 479 × TZEEIOR 197, and TZEEIOR 458 × TZEEIOR 197 were identified as the most stable hybrids across drought and well-watered conditions. These hybrids should be extensively tested in multi-location trials for deployment and commercialization in SSA.

Tree condition, pruning and orchard management practices within intensive horticultural tree crop systems can be determined via measurements of tree structure. Multi-spectral imagery acquired from an unmanned aerial system (UAS) has been demonstrated as an accurate and efficient platform for measuring various tree structural attributes, but research in complex horticultural environments has been limited. This research established a methodology for accurately estimating tree crown height, extent, plant projective cover (PPC) and condition of avocado tree crops, from a UAS platform. Individual tree crowns were delineated using object-based image analysis. In comparison to field measured canopy heights, an image-derived canopy height model provided a coefficient of determination (R2) of 0.65 and relative root mean squared error of 6%. Tree crown length perpendicular to the hedgerow was accurately mapped. PPC was measured using spectral and textural image information and produced an R2 value of 0.62 against field data. A random forest classifier was applied to assign tree condition into four categories in accordance with industry standards, producing out-of-bag accuracies >96%. Our results demonstrate the potential of UAS-based mapping for the provision of information to support the horticulture industry and facilitate orchard-based assessment and management.

A compact Mach-zehnder interferometer with a novel design of directional couplers and a phase shifter has been presented as a thermo-optical sensor. With the aim of reducing device size to micro and nano dimension silicon-on-insulator technology was employed. That allowed miniaturization of device size through the reduction of its cross sectional area to 0.066 µm² and the radius of curvature of both the arms of the directional coupler and S-bends of the phase shifter to 5 µm and C-bends to 3 µm. These nano size device dimensions made it possible to reduce the coupling gap to 0.2 µm, which resulted in a significant reduction in the coupling length. The device geometry and its performance characteristics were analyzed and optimized using coupled mode analysis and finite difference time domain simulation tools, respectively. The wavelength dependent transmission loss of the device was measured at different temperature to verify and validate its performance characteristics. Tested devices showed a remarkable temperature dependent transmission characteristic offering significant changes in transmission loss band – with as low as 0.45 ⁰C change in substrate temperature. The extinction ratio and the free spectral range of the device were 26 dB and 0.26 nm respectively in the wavelength range of 1549.5 nm – 1550.5 nm. These results imply that the devices presented here can be used as compact and highly sensitive thermal sensors and optical switches.

Adaptations to climate change rely on understanding the dynamics of plant biomass stocks on the planet. The high levels of deforestation in Cerrado have transformed this biome into the second-largest Brazilian source of carbon emissions. The objective of this study was to develop a method to accurately estimate aboveground and total biomass values among shrublands, savannas, and forests located in the Cerrado biome, using an allometric equation adjusted from canopy height, obtained through optical and laser sensors. The results show similarity between the estimates employed by our method and the data found in the literature review for different phytophysiognomies in the Cerrado biome. Shrubland formations showed higher biomass estimation uncertainties due to the discontinuity of isolated trees and the lower canopy height when compared to more clustered tree canopies in savannas and taller canopies in forests. Aboveground biomass estimates were related to expansion factors, and specific maps were developed for each compartment by root, litter, and necromass. The sum of these compartments is presented in the aboveground and below forest biomass map. This study presents, for the first time, the mapping of total biomass in 10 m pixels of all regions of the Cerrado biome.

The antimicrobial properties of the new strains of microorganisms isolated from natural sources of various ecological niches in the Moscow Region and the Republic of Tatarstan were studied. An antifungal activity of isolates was established in a test culture of toxin-producing microscopic fungi that cause various plant diseases: Fusarium oxysporum, Aspergillus flavus, Penicillium spp. and Candida albicans. Of the 46 studied microorganisms, 4 isolates (Bacillus subtilis, Propionibacterium freudenreichii, Lactobacillus plantarum and Streptomyces spp.) showed an ability to produce biologically active metabolites with a pronounced antimicrobial potential. This is promising in the growth and protection of the Scots pine, pedunculate oak and small-leaved linden forest crops from diseases caused by fungi Lophodermium pinastri Chev. and Microsphaera alphitoides stimulation. Based on selected isolates, a Bacterial product LRV composition has been developed. A Scots pine, pedunculate oak and small-leaved linden seedlings single and double foliar treatment with Bacterial product LRV at a concentration of 10 ml/l led to an increase in the growth of an above-ground part by 31.8, 51.9 and 25.4 %, respectively, and an underground part – by 25.0, 37.2 and 25.7 %, respectively, compared with the control. The weight of seedling at the end of the study exceeded the control variant by an average of 26.0, 44.0 and 78.0 %, respectively. A use of a plant protection Bacterial product LRV did not have a significant effect on a powdery mildew and Schütte disease damage to forest crops. A Biogeosystem Technique methodology has been developed to improve a long-term forest growing.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

Separase is a key cysteine protease to separate sister chromatids through digestion of cohesion ring that inhibits chromosome segregation as trigger of metaphase–anaphase transition in eukaryotes and highly regulated its activity by binding with securin and cyclinB-CDK1 complex. Those bindings prevent proteolytic activity of separase until the onset of anaphase. Chromosome missegregation and aneuploidy are frequently observed in malignancies. However, there are some difficulties for biochemical examinations due to instability of separase in vitro and a few spatiotemporal resolution approaches monitoring live separase activity throughout mitotic processes. Here we have developed FRET-based molecular sensors including GFP variants with separase cleavable sequences as donor and covalently attached fluorescent dye as acceptor molecules applicable to conventional live cell imaging and flow cytometric analysis because of efficient live cell uptake. We investigated performance of equivalent molecular sensors localized or not localized inside nucleus under cell cycle control using flow cytometry. Synchronized cell cycle progression rendered significant separase activity detections in both molecular sensors. We obtained consistent outcomes with localized molecular sensor introduction and cell cycle control by fluorescent microscopic observations. We thus established live cell separase activity monitoring systems specifically or statistically that could lead to elucidate separase properties in detail.

Studies on the domestication, genetic differentiation, and crop evolution of foxtail millet are re-viewed. Several genetic studies were carried out to elucidate the genetic relationships among foxtail millet accessions originating mainly from Eurasia, based on intraspecific hybrid pollen semi-sterility, isozymes, DNA markers, and single-nucleotide polymorphisms. Most studies suggest that China is the center of diversity of foxtail millet, and landraces were categorized into geographical groups. Furthermore, the evolution of genes was reviewed (i.e., the Waxy gene conferring amylose content in the endosperm, the Si7PPO gene controlling polyphenol oxidase, the HD1 and SiPRR37 genes controlling heading time, the Sh1 and SvLes1 genes involved in grain shattering, and the C gene controlling leaf sheath pigmentation), and the variation and distribu-tion of these genes suggested complex patterns of evolution under human and/or natural selec-tion.

Originally developed to image the shadow region of the central black hole in Sagittarius A* and in the nearby galaxy M87, the Event Horizon Telescope (EHT) provides deep, very high angular resolution data on other AGN sources too. The challenges of working with EHT data have spurred the development of new image reconstruction algorithms. This work briefly reviews the status of the EHT and its utility for observing AGN sources, with emphasis on novel imaging techniques that offer the promise of better reconstructions at 1.3 mm and other wavelengths.

Active ageing is defined as the process of optimizing opportunities for physical, social and mental health to enable older people to take an active part in society without discrimination and to enjoy an independent and good quality of life. The World Health Organization assumed this as a process for increasing and maintaining an individual’s participation in activities to enhance his/her quality of life. In this survey, the authors addressed the following question: “Is assistive technology (AT) for mobility contributing to enhancement of lifelong capacity and performance?”. From June 2015 until February 2016, 96 community dwelling adults, AT users for mobility (powered wheelchairs, manual wheelchairs, lower limb prostheses, walkers, crutches and canes), aged 45-97, mean 67.02 +/- 14.24 years old, 56.3% female, were interviewed using the Psychosocial Impact of Assistive Devices Scale (P-PIADS), the Activities and Participation Profile related to Mobility (APPM) and demographics, clinical and questions about AT use and training. The participants’ profiles revealed moderate limitation and restrictions in participation, measured by the APPM (2.03). Most participants showed positive impact of AT; average scores obtained from the P-PIADS subscales were: Self-esteem 0.62, Competency 1.11 and Adaptability 1.10. P-PIADS total was 0.96, with the powered wheelchair users scoring the highest (1.53) and the walker users scoring the lowest (0.73). All subscales and P-PIADS total were positively correlated with the activities and participation profile. There was no relation between age and the psychosocial impact of AT or activities and participation profile. These results encourage the authors to follow these participants up for a lifelong intervention. To accomplish that aim, currently, the protocol is implemented at the AT prescribing centers in Coimbra, Portugal in order to assess the impact of AT on participation in society, one of the domains of the Active Ageing Index, a new analytical tool to help policy makers in developing policies for active and healthy ageing.

UAV-captured multispectral imagery was used to characterize and associate Moriche’s palm 1 canopy features with the maturity stage of the corresponding fruits. Deep learning models based on 2 convolutional neural networks (CNN) were trained in order to determine correlations between the 3 photosynthetic radiation of the palms with the fruit. Here, we compare several approaches for feature 4 extraction based on vegetation indices and graph-based models. Also, a comprehensive dataset has 5 been collected and labeled, containing plant data for an entire phenological cycle of the Moriche 6 palms. Experimental results reported an average estimation accuracy of 72%, by using the proposed 7 method in dense forests of the Amazonian region.

Forest canopy gaps are important for the ecosystem dynamics. Depending on tree species, small canopy openings might be also associated to intra-crown porosity and to space between crowns. Yet, little is known on the relationships between the fine-scaled pattern of canopy openings and biodiversity features. This research explored the possibility of i)- mapping forest canopy gaps from a very high resolution orthomosaic (10 cm), processed from a versatile imaging platform such as unmanned aerial vehicles (UAV), ii)- to derive patch metrics that can be tested as covariates of variables of interest for forest biodiversity monitoring. This is attempted in a test area of 240 ha covered by temperate deciduous forest types in Central Italy and containing 50 forest inventory plots of about 530 m². Correlation and linear regression techniques were used to explore relationships between patch metrics and understorey (density, development and species diversity) or forest habitat biodiversity variables (density of micro-habitat bearing trees, vertical species profile, tree species diversity). The results revealed that small openings in the canopy cover (75% smaller than 7 m²) can be faithfully extracted from UAV RGB imagery, using the red band and contrast split segmentation. Highest correlations were observed in the mixed forest (beech and turkey oak), while beech forest had the poorest ones and turkey oak forest displayed intermediate results. Moderate to strong linear relationships were found between gap metrics and understorey variables in mixed forest type, with adjusted R² from linear regression ranging from 0.52 to 0.87. Equally good results, in the same forest types, were observed for forest habitat biodiversity variables (0.52<adjusted R²<0.79) with highest values found for density of trees with microhabitats and vertical species profile. In conclusion, this research highlights that UAV remote sensing can potentially provide covariate surfaces of variables of interest for forest biodiversity monitoring, conventionally collected in forest inventory plots. By integrating the two sources of data, these variables can be mapped over small forest areas with satisfactory levels of accuracy, at a much higher spatial resolution than would be possible by field-based forest inventory solely.

Endophytic microbes are a ubiquitous group of plant-associated communities that colonize the intercellular or intracellular host tissues while giving numerous beneficial effects to the plants. All the plant species are thought to be associated with endophytes, majorly constituted with bacteria and fungi. During the last two decades, there has been a considerable movement toward the study of endophytes associated with coffee plants. In this review, the main consideration is given to address the coffee-associated endophytic bacteria and fungi, particularly their action on plant growth promotion and the biocontrol of pests. In addition, we sought to identify and analyze the gaps in available research. Additionally, the potential of endophytes to improve the quality of coffee seeds is briefly discussed. Even though there are limited studies on the subject, it has been well recognized the potentiality of coffee endophytes in plant growth promotion through enhancing nitrogen fixation, availability of minerals, nutrient absorption, secretion of phytohormones, and other bioactive metabolites. Further, the antagonistic effect against various coffee pathogenic bacteria, fungi, nematodes, and also insect pests lead to the protection of the crop. Furthermore, it is recognized that endophytes enhance the sensory characteristics of coffee as a new field of study.

In Bangladesh, climate change is a major concern because of its geophysical location and climate dependent agriculture. As sessile organisms, crops plants have to face difficulties often in this environmentally vulnerable country. Therefore, this study examines the seasonal trend of two climatic parameters viz. temperature (maximum and minimum) and rainfall over a period of 1983 to 2013. Besides, this study provides insight into the relationship between climatic parameters and crop yield of two major crops viz. rice and wheat during 1997-2013. To assess the relationship of climatic parameters with time and yield using Pearson correlation analysis, time series data used at an aggregate level. SPSS software utilized for this analysis. The cropping seasons such as rice growing seasons Aus (summer rice), Aman (autumn rice) and Boro (winter rice) exhibited a significant increase in maximum and minimum temperature. Rainfall found to have a decreasing trend for all the seasons. This study also revealed that the climatic parameters had significant effects on rice yield, but these results varied among three rice crops. Maximum temperature had positive effects on all rice yields, especially on Aus and Aman. Minimum temperature had a negative effect on Aman rice yield but a positive effect on Aus rice yield. Wheat yield negatively associated with temperature. Rainfall exhibited negative relation with both rice and wheat yield.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

Ultrasound, as mechanical waves with frequencies exceeding 20 thousand hertz, has found wide applications in medicine, physiotherapy, and more recently in agriculture. This study aimed to investigate the impact of ultrasound on potato yield and its parameters, particularly on seed potato yield, quantity, mass, and multiplication coefficient of potato tubers. The research was based on a three-year field experiment, utilizing the randomized block design in a split-split-plot arrangement, in the central-eastern region of Poland. The primary factor were technologies: a) technology with employing ultrasonic pre-planting treatment, b) traditional cultivation without this treatment. The secondary factors were potato varieties. Sonication of tubers was conducted using a bath-type ultrasonic device equipped with piezoe-lectric transducers. Results revealed a significant influence of cultivation technology, cultivar, and weather conditions on seed tubers yield, quantity, and multiplication coefficient of potato tubers. However, genetic traits of the examined varieties and random factors significantly affected the individual seed tuber mass and the number of shoots emerging from a single tuber. Future Outlook: Future research could focus on further optimizing ultrasound application techniques in potato cultivation, considering diverse varieties and environmental conditions. Additionally, it would be worthwhile to analyze the long-term effects of ultrasound on tuber seed potato quality and their ability to adapt to changing climatic and soil conditions. Furthermore, studies investi-gating the impact of ultrasound on other plant species could broaden our understanding of po-tential benefits in agriculture.

The growing attention for plug-in electric vehicles, and the associated high-performance demands, have initiated a development trend towards highly efficient and compact on-board battery chargers. These isolated ac-dc converters are most commonly realized using two conversion stages, combining a non-isolated power factor correction (PFC) rectifier with an isolated dc-dc converter. This, however, involves two loss stages and a relatively high component count, limiting the achievable efficiency and power density and resulting in high costs. In this paper a single-stage converter approach is analyzed to realize a single-phase ac-dc converter, combining all functionalities into one conversion stage and thus enabling a cost-effective efficiency and power density increase. The converter topology consists of a quasi-lossless synchronous rectifier followed by an isolated dual active bridge (DAB) dc-dc converter, putting a small filter capacitor in between. To show the performance potential of this bidirectional, isolated ac-dc converter, a comprehensive design procedure and multi-objective optimization with respect to efficiency and power density is presented, using detailed loss and volume models. The models and procedures are verified by a 3.7 kW hardware demonstrator, interfacing a 400 V dc-bus with the single-phase 230 V, 50 Hz utility grid. Measurement results indicate a state-of-the-art efficiency of 96.1% and power density of 2.2 kW/dm³, confirming the competitiveness of the investigated single-stage DAB ac-dc converter.

Crop breeding is an important global strategy to meet sustainable food demand. CRISPR-Cas is a most promising gene-editing technology for rapid and precise generation of novel germplasm, and leads to revolutionary crop breeding innovation. In this review, we summarize recent advance of CRISPR/Cas technology in gene function analyses and generation of new germplasms with increased yield, improved product quality, and enhanced resistance to biotic and abiotic stress. We highlight their applications and breakthroughs in agriculture including crop de novo domestication, decoupling the gene pleiotropy tradeoff, crop hybrid seed conventional production, hybrid rice asexual reproduction, and double haploid breeding. Moreover, the challenges and development of CRISPR/Cas technology in crops are also discussed.

In the last 20 years, an increasing number of studies have been reported on membrane active peptides, which exert their biological activity by interacting with the cell membrane either to disrupt it and lead to cell lysis or to translocate through it to deliver cargos into the cell and reach their target. These peptides are attractive alternatives to currently used pharmaceuticals. Antimicrobial peptides (AMPs) and peptides designed for drug and gene delivery currently in the drug pipeline suggest that these membrane active peptides will soon constitute a significant percentage of the drug market. Here, we focus on two most prominent classes of membrane active peptides; AMPs and cell-penetrating peptides (CPPs). AMPs are a group of membrane active peptides that disrupt the membrane integrity or inhibit the cellular functions of bacteria, virus and fungi. CPPs are another group of membrane active peptides that mainly function as cargo-carriers even though they may also show antimicrobial activity to some extent. Biophysical techniques to understand how they interact with the membrane have shed light on the peptide–membrane interaction at various levels of detail. Structural investigation of membrane active peptides in the presence of the membrane provides important clues on the effect of the membrane environment on peptide conformations. Advances in live imaging techniques have allowed examination of peptide action at a single cell or single molecule level. In addition to these experimental biophysical techniques, molecular dynamics simulations provided clues on the peptide-lipid interactions and dynamics of the cell entry process at atomic detail. In this review, we summarize the recent advances in experimental and computational investigation of membrane active peptides with particular emphasis on two amphipathic membrane active peptides, the AMP melittin and the CPP pVEC.

Crop phenotyping data collection is the basis for precision agriculture and smart decisionmaking applications. In this study, a dynamic slicing and reconstruction canopy volume (DR) algorithm is proposed to accurately estimate citrus canopy volume. The algorithm dynamically slices nearby slices based on their proportional area change and density difference, subsequently conducting AS reconstruction and volume calculation for each slice using an iterative mean point spacing as the α-value. Compared with six point cloud-based reconstruction algorithms, the DR approach achieved the best results in removing perforations and lacunae (0.84) and exhibited volumetric consistency (1.53) that closely aligned with the growth pattern of citrus trees. The DR algorithm effectively addresses the challenges of adapting the thickness and number of canopy point cloud slices to the shape and size of the canopy in the ASBS and CHBS algorithms, as well as overcoming inaccuracies and incompleteness in reconstructed canopy models caused by limitations in capturing detailed features using the PCH algorithm. It offers improved adaptive ability, finer volume computations, better noise reduction, and anomaly removal. In conclusion, we recommend selecting appropriate operating environments for each algorithm based on their principles, geometric properties, volumetric values, running time, and linear relationships with one another to guide orchard mechanization and intelligent operation.