MoS2 lithium-based grease is suitable for lubrication protection between bearings at high temperatures and loads due to its excellent tribological properties. However, there is little research on the influence of different addition methods of MoS2 additive on the tribology and corrosion properties of lithium grease. In this work, vegetable oil with low toxicity, high biodegradation rate, and low cost was selected as the base oil, lithium 12-hydroxystearate as the thickener, and MoS2 as the additive. The effects of different adding modes of MoS2 on the tribology and corrosion properties of lithium grease were studied. The experimental results showed that adding 0.01wt% MoS2 before thickening was more conducive to improving the tribological properties of lithium grease. The average friction coefficient was 0.034, and the average spot diameter was reduced by 0.16mm. After grinding and adding 0.01wt% MoS2, the corrosion inhibition efficiency of the steel sheet was as high as 96.97%. The main reason was that the longer stirring and grinding were conducive to the uniform distribution of MoS2 in the grease, and the protective film formed by MoS2 and GCr15-bearing steel improved the lubrication performance and corrosion inhibition performance of the friction system.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

Six bacterial strains with differing abilities to produce varying concentrations of Indole Acetic Acid were tested individually and in consortia for plant growth promoting and fitness related traits of Cicer arietinum. In all experiments the presence of the nitrogen fixer Mesorhizobium ciceri resulted in increased biomass production. In the absence of this strain, IAA Psedomonas putida and Bacillus megaterium hinder plant growth and fitness related traits. The application of mixes of the three strains always resulted in better plant performance when M. ciceri was present. Whereas P. putida has a noticeable plant growth-promoting effect B. megaterium resulted less effective. The low levels of IAA produced by the selected strains had a significantly greater positive effect on plant biomass accumulation, flower, pods and seed production as well as on total plant nitrogen and nitrogen concentration in seed than high IAA producer strains.

Although Eulerian approaches are standard in computational acoustics, they are less effective for certain classes of problems like bubble acoustics and combustion noise. A different approach for solving acoustic problems is to compute with individual particles following particle motion. In this paper, a Lagrangian approach to model sound propagation in moving fluid is presented and implemented numerically, using three meshfree methods to solve the Lagrangian acoustic perturbation equations (LAPE) in the time domain. The LAPE split the fluid dynamic equations into a set of hydrodynamic equations for the motion of fluid particles and perturbation equations for the acoustic quantities corresponding to each fluid particle. Then, three meshfree methods, the smoothed particle hydrodynamics (SPH) method, the corrective smoothed particle (CSP) method, and the generalized finite difference (GFD) method, are introduced to solve the LAPE and the linearized LAPE (LLAPE). The SPH and CSP methods are widely used meshfree methods, while the GFD method based on the Taylor series expansion can be easily extended to higher orders. Applications to modeling sound propagation in steady or unsteady fluids in motion are outlined, treating a number of different cases in one and two space dimensions. A comparison of the LAPE and the LLAPE using the three meshfree methods is also presented. The Lagrangian approach shows good agreement with exact solutions. The comparison indicates that the CSP and GFD method exhibit convergence in cases with different background flow. The GFD method is more accurate, while the CSP method can handle higher Courant numbers.

The principal main of this research work was the study the influence of Cu addition on the wear behavior (WB) of eutectic Al-12.6Si alloy developed by spray forming (SF) method and compared with as-cast (AC) alloys. The phases of chemical compositions and microstructure were studied by optical microscopy, energy dispersive spectroscopy (EDS) and Scanning Electron Microscopy (SEM). The microstructure of SFAl-12.6Si (SF1) alloy reside — of fine primary and eutectic Si phases evenly distributed in the equiaxed α-Al matrix and SF Al-12.6Si-2Cu (SF2) alloy lie of uniformly distributed fine eutectic Si particulates and spherical form θ-Al2Cu precipitates in α-Al matrix. On other hand, the AC Al-12.6Si alloy (AC1) alloy involve of eutectic Si needles in the dendrite α-Al matrix, whereas AC Al-12.6Si-2Cu (AC2) alloy consisted of eutectic Si needles and Chinese script form θ phase distributed randomly in the α-Al matrix. The microhardness and wear properties were analyzed using Vickers hardness (VH) and dry sliding WT. The SF alloys exhibit superior hardness compared to the AC alloys. The wear properties of SF alloys exhibited significantly superior compared to the AC alloys. The SF2 alloy showed high wear resistance (WR) than the SF1 alloy in the entire sliding velocities and applied loads. The results indicate that the spray deposited alloys have a lower coefficient of friction (CF(µ)) than the AC alloys under varying load and sliding velocity conditions. The high WR in the SF alloy was due to microstructural modification during SF and precipitation of fine Al2Cu intermetallic and solid solubility effects. The SF2 depicts increased transition from oxidative to abrasive. In other ways, AC alloys demonstrate wear mechanisms that change from oxidative to abrasive and delamination with an increase in sliding velocity and load.

The branch prediction units (BPUs) generally have security vulnerabilities, which can be used by attackers to obtain the execution status, jump directions, and jump address of conditional branches, and the existing protection methods cannot defend against these attacks. Therefore, this article proposes a hardware security protection method for conditional branches of embedded systems. This method calculates the number of updates to the branch target buffer (BTB). When it exceeds the threshold, BTB is locked to prevent attackers from analyzing the execution status of branches based on the time difference of whether BTB is updated. Moreover, the hybrid physical unclonable function (PUF) circuit is designed to provide confidentiality protection for the jump directions, jump addresses, and their indexes, preventing attackers from stealing these critical data. If these mechanism fails and attackers successfully tamper with conditional branches, this paper proposes a control flow integrity (CFI) protection mechanism based on branch labels to timely detect tampering with instruction codes, jump addresses, and jump directions. The proposed method is implemented and tested on FPGA. The experimental results show that this method can achieve fine-grained security protection for conditional branches, with about 5.4% resource overhead and less than 5.5% performance overhead.

(1) Background: The definition of value addition is based on the process or processes which are used to transform physically the initial raw material in the final food or non-food article. Diversification can enhance the possibility of increased gains. The aim of this work is to give a reliable description of value addition when speaking of coconut-based beverages among all possible derivatives; (2) Methods: a systematic review of main papers on the argument has been critically examined and discussed; (3) Results: Processing degree is a consequence of consumers’ requests. Three different drivers for value addition have been considered: packaging, durability, and size options; sensorial features; and sustainability. Results of this investigation have highlighted the added value of several products because of recyclable packaging materials, intermediate or long durability expectations, different available sizes, and good or excellent sensorial performances; (4) Conclusions: There are different value-added coconut-based beverages with interesting perspectives. On the other side, sustainability and eco-friendly policies may be a problem for those products which are produced similarly to non-coconut based beverages. The opportunity of certified organic and/or fair-trade products could help the industry of coconuts in the next future. More research is still needed in this ambit.

Rapid and accurate detection of road cracks is of great significance for road health monitoring, but currently this work is mainly completed through manual site surveys. Low-altitude UAV remote sensing can obtain images with centimeter or even subcentimeter ground resolution, which provides a new efficient and economical approach for rapid crack detection. Nevertheless, crack detection networks face challenges such as edge blurring and misidentification due to the heterogeneity of road cracks and the complexity of the background. To address these issues, we propose a real-time edge reconstruction crack detection network (ERNet) which adopts multi-level information aggregation to reconstruct crack edges and improve the accuracy of segmentation between the target and background. To capture global dependencies across spatial and channel levels, we propose an efficient bilateral decomposed convolutional attention module (BDAM) that combines depth separable convolution and dilated convolution to capture global dependencies across spatial and channel levels. To enhance the accuracy of crack detection, we use a coordinate-based fusion module that integrates spatial, semantic, and edge reconstruction information. In addition, we propose an automatic measurement of crack information for extracting the crack trunk and its corresponding length and width. Experimental results demonstrate that our network achieves the best balance between accuracy and inference speed.

Abstract In order to solve the problem that it is difficult to obtain the accurate trigger signal moment when using the time difference of UAV flight acoustic signals collected by acoustic sensors arranged in advance to locate the position of UAVs when they cannot be tracked by radar and are difficult to be observed by the human eye, an acoustic source localisation method with improved empirical modal decomposition (REMD) under an adaptive frequency window is proposed. Firstly, the collected UAV flight signals are smoothed and filtered, then the robust empirical modal decomposition (REMD) is used for IMF modal decomposition and spectral analysis of the collected signals, and a panning frequency window with variable bandwidth is introduced for corresponding frequency locking and extracting the IMFs; the GWO optimisation is used and the sliding metrics are set to determine the position of the panning frequency window automatically; finally, the extracted Finally, the extracted IMF components are reconstructed according to the criterion, and the trigger signal moments in the reconstructed IMF components are resolved and recorded, and the algorithm is used to calculate the difference between the reception moments of different sensors; for the traditional sound source localisation algorithms with a small detection range, which are prone to fall into the no-solution or false-solution, i.e., unable to achieve the localisation, a weighted least-squares-based Chan-Taylor algorithm is proposed for the localisation computation, and a weighted least-squares algorithm is proposed for the localisation computation, through the Inputting the sensor delay parameter and solving the linear equation system to get the target position information; finally, this paper verifies the robustness and performance of the design method with simulated and actual signals. The results show that the maximum positioning error is no more than 5% in an area with a side length of 15m in the measurement area. With the improved accuracy of time delay estimation, the positioning simulation results meet the positioning requirements even though the positioning error is further expanded when the measurement area is further expanded.

The segmentation of abnormal regions is vital in smart manufacturing. However, the existing segmentation system for detecting sauce-packet leakage on intelligent sensors encounters an issue of imaging blurring caused by uneven illumination. This issue adversely affects segmentation performance, thereby impeding the rapid production of industrial assembly lines. To alleviate this issue, we propose the two-stage Illumination-aware Sauce-packet Leakage Segmentation (ISLS) method for intelligent sensors. The ISLS comprises two main stages: Illumination-aware region enhancement and leakage region segmentation. In the first stage, YOLO-Fastestv2 is employed to capture the Region of Interest (ROI), which reduces redundancy computations. Additionally, we propose an image enhancement to relieve the impact of uneven illumination, enhancing the texture details of ROI. In the second stage, we propose a novel feature extraction network. Specifically, we propose the Multi-scale Feature Fusion Module (MFFM) and the Sequential Self-Attention Mechanism (SSAM) to capture discriminative representations of leakage. The multi-level features are fused by MFFM with a small number of parameters, which capture leakage semantics at different scales. The SSAM realizes the enhancement of valid features and the suppression of invalid features by adaptive weighting of spatial and channel dimensions. Furthermore, we generated a self-built dataset of sauce-packets, including 606 images with various leakage areas. Comprehensive experiments demonstrate that our ISLS method shows better results than several state-of-the-art methods, with additional performance analyses deployed on intelligent sensors to affirm the effectiveness of our proposed method. Our code is available at https://github.com/LSJ5106/SauceDetect.

We propose a neural-network-based watermarking method that introduces the quantized activation function that approximates the quantization of JPEG compression. Many neural-network-based watermarking methods have been proposed. Conventional methods have acquired robustness against various attacks by introducing an attack simulation layer between the embedding network and the extraction network. The quantization process of JPEG compression was replaced by the noise addition process in the attack layer of the conventional methods. In this paper, we propose a quantized activation function that can simulate the JPEG quantization standard as it is in order to improve the robustness against the JPEG compression. Our quantized activation function consists of several hyperbolic tangent functions and is applied as an activation function for neural networks. Our network was introduced in the attack layer of ReDMark proposed by Ahmadi et al. to compare it with their method. That is, the embedding and extraction networks had the same structure. We compared the usual JPEG compressed images and the images applying the quantized activation function. The results showed that a network with quantized activation functions can approximate JPEG compression with high accuracy. We also compared the bit error rate (BER) of estimated watermarks generated by our network with those generated by ReDMark. We found that our network was able to produce estimated watermarks with lower BERs than those of ReDMark. Therefore, our network outperformed the conventional method with respect to image quality and BER.

As argued by ‘Declaration of Concrete Environment (2010)’ of Korea and ‘Declaration of Asian Concrete Environment (2011)’ of six Asian countries, concrete as a single material has lately shown extremely large impact on environmental issues such as climate change. Assessment of environmental impact from concrete material and production has considerable importance. Concrete is a major material used in the construction industry that emits a large amount of substances with environmental impacts during its life cycle. Accordingly, technologies for the reduction in and assessment of the environmental impact of concrete from the perspective of Life Cycle Assessment must be developed. At present, the studies in relation to greenhouse gas emission from concrete are being carried out globally as a countermeasure against climate change. In this study, a sustainable concrete mix design algorithm was designed using correlation analyses, and its carbon emission and cost reduction performances were assessed. Using correlation analyses, the concrete strength, w/b and s/a ratios, and CO₂ emissions were identified as major variables of concrete mix design that influenced other variables. Also, this study aims to evaluate the CO₂ emission reduction performance of the algorithm-deduced sustainable concrete mix design, and therefore, the CO₂ emissions of the sustainable concrete mix design are compared with those of the actual concrete mix design applied to the construction of the office building A in South Korea.

The accompanying mechanical behavior during the flow of ore-rock dispersion is an important factor leading to the instability and failure of the orepass in the ore storage section. It is of great significance to accurately understand the instability characteristics of the well wall in the ore section, during the ore drawing process by understanding the flow characteristics and internal mechanical transfer mechanism of ore-rock dispersion. Using the discrete element method to analyze the flow characteristics, contact compactness, stress distribution characteristics and contact force probability distribution of the ore-rock dispersion, it realizes the quantitative characterization of the damage degree of ore-rock flow, and reveals the damage mechanism of mine storage wall. The results show that: (1) The friction between ore-rock particles, between ore-rock and well wall is an important reason for the change of the macroscopic flow form of ore-rock from “one” to “V” type. (2) The compactness and stress concentration of ores are increasing with the increase of storage depth, which is shown that with the increase of storage depth, the greater the probability of well wall instability. (3) The probability distribution of contact force strength between particles decreases exponentially in the whole process of ore drawing, in which the strong chain plays a major role in the stability of the dispersion system. (4) The number of overpressure and the overpressure coefficient can be used to quantitatively characterize the wall damage degree under the action of ore-rock flow. The dynamic side pressure decreases periodically in the form of exponential fluctuations, and the dynamic load formed by the ore-rock flow mainly played a role in the lower area of the ore storage section.

With the integrated development of the Internet, wireless sensor technology, cloud computing, and mobile Internet, there has been a lot of attention given to research about and applications of the Internet of Things. A Wireless Sensor Network (WSN) is one of the important information technologies in the Internet of Things; it integrates multi-technology to detect and gather information in a network environment by mutual cooperation, using a variety of methods to process and analyze data, implement awareness, and perform tests. This paper mainly researches the localization algorithm of sensor nodes in a wireless sensor network. Firstly, a multi-granularity region partition is proposed to divide the location region. In the range-based method, the RSSI (Received Signal Strength indicator, RSSI) is used to estimate distance. The optimal RSSI value is computed by the Gaussian fitting method. Furthermore, a Voronoi diagram is characterized by the use of dividing region. Rach anchor node is regarded as the center of each region; the whole position region is divided into several regions and the sub-region of neighboring nodes is combined into triangles while the unknown node is locked in the ultimate area. Secondly, the multi-granularity regional division and Lagrange multiplier method are used to calculate the final coordinates. Because nodes are influenced by many factors in the practical application, two kinds of positioning methods are designed: the unknown node is in the positioning unit or not. When the unknown node is on the side of the positioning unit, we use the method of vector similarity. Moreover, we use the centroid algorithm to calculate the ultimate coordinates of unknown node. When the unknown node is not on the side of the positioning unit, we establish a Lagrange equation containing the constraint condition to calculate the first coordinates. Furthermore, we use the Taylor expansion formula to correct the coordinates of the unknown node. In addition, this localization method has been validated by establishing the real environment.

The development of computational acoustics allows simulation of sound generation and propagation in complex environment. In particular, meshfree methods are widely used to solve acoustics problems through arbitrarily distributed field points and approximation smoothness flexibility. As a Lagrangian meshfree method, smoothed particle hydrodynamics (SPH) method reduce the difficulty in solving problems with deformable boundaries, complex topologies, or multiphase medium. The traditional SPH method has been applied in acoustic simulation. This study presents the corrective smoothed particle method (CSPM), which is a combination of SPH kernel estimate and Taylor series expansion. The CSPM is introduced as a Lagrangian approach to improve accuracy in solving acoustic wave equations in the time domain. Moreover, a boundary treatment technique based on the hybrid meshfree and finite difference time domain (FDTD) method is proposed to represent different acoustic boundaries with particles. To model sound propagation in pipes with different boundaries, soft, rigid, and absorbing boundary conditions are built with this technique. Numerical results show that the CSPM algorithm is consistent and demonstrates convergence with exact solutions. Main computational parameters are discussed, and different boundary conditions are validated to be effective for benchmark problems in computational acoustics.

Introduction of Cl- and O- atoms into C4-vinyl carbocations was studied by X-ray diffraction analysis and IR spectroscopy. Chlorine atoms are weak electron acceptors in ordinary molecules, but within vinyl carbocations, manifest themselves as strong electron donors that accept a positive charge. The attachment of a Cl atom directly to a C=C bond leads to an increase in the e-density on it, exceeding that of the common double bond. The positive charge should be concentrated on the Cl atom, and weak δ- may appear on the C=C bond. More distant attachment of the Cl atom—to a C atom adjacent to the C=C bond—has a weaker effect on it. If two Cl atoms are attached to the Сγ atom of the vinyl cation, as in Cl2СγСδHСαHCH3, then the cation switches to the allyl type with two practically equivalent and almost uncharged СγСδСα bonds. When such a strong nucleophile as the O atom is introduced into the carbocation, a protonated ester molecule with a C-O(H+)-C group and a C=C bond forms. Nonetheless, in the future, there is still a possibility of obtaining carbocations with a non-protonated C-O-C group.

The wellness economy has developed rapidly recently, particularly in wellness tourism. Wellness tourism transforms sustainable strategy through the availability of extended multi-actor engagement in service innovation to further the tourism experience. Therefore, when operating a wellness tourism destination, it is necessary to encourage multi-actor engagement in service innovation to achieve sustainable development. This paper introduces a mixed research method with the SWOT-AHP-QSPM, as it qualitatively analyzes the advantages, disadvantages, opportunities, and threats, constructs an evaluation index system, conducts quantitative analysis using the analytic hierarchy process, determines the index weight and weighted score, and calculate the sustainable development strategy, which is appropriate for wellness development of Chongqing Tea Mountain and Bamboo Forest National Forest Park. Purposive field surveys and personal interviews were conducted in Chongqing forest tourism destinations, involving 356 effective respondents. The research reveals that multi-actor engagement significantly enhances sustainable development. These findings bridge service innovation knowledge gaps and provide valuable insights for forest tourism destination management and sustainable policy strategies to elevate multi-actor engagement in forest sites.

By repeated unloading and loading of the excavation dynamic and static loads, repeated train dynamic and static loads of multi-factors, the underpass tunnel, cross tunnel engineering influence area rock layer, the existing tunnel structure of the three constitutes a multifaceted structure, multi-factor interaction system. Existing tunnels into the prediction theory model of the new tunnel excavation process of dynamic and static loads, dynamic and static loads of existing tunnels are mostly analyzed individually, the results of synergistic analysis needs to be improved. Based on the theory of the current layer method, the paper comprehensively considers the stiffness of the existing tunnel, the stiffness of the new tunnel, the excavation method load and the existing tunnel load, coupled with Peck's empirical formula, the theoretical model of deformation prediction for excavation of a two-lane highway tunnel under the tunnel through the existing railroad is proposed, and verified and optimized by numerical calculations and monitoring data, which proves the applicability and reliability of the theoretical model in the similar strata and the project promotion.

The effects of co-addition CeO2 and SiC particles on the morphology, surface cracks, microstructure, precipitated phases and wear property of plasma beam spraying Fe55-based coatings on 1025 steel were investigated by optical microscopy (OM), scanning electron microscopy (SEM), energy-dispersive X-ray spectrometer (EDS), ultra-deep field microscope and wet sand rubber wheel friction tester, respectively. The results showed that the dendrite exhibited a directional growth pattern perpendicular to the substrate and the transitional states of microstructure with the co-addition CeO2 and SiC particles. With addition of CeO2 or SiC affected the flowability of molten steel at macro level, leading to a reduction in the liquid phase diffusion coefficient DL of Cr and C and resulted in a decrease in the G/R ratio. The dendrites changed into equiaxed grains. The main phase composition of Fe55 welding layer is Cr7C3, γ-Fe. The grain boundaries consisted mainly of a reticular eutectic structure. The worn-out uniformly surface of the Fe55+1.5 wt% SiC+0.01wt% CeO2 with Ra was 0.28 μm was smoother than that of other samples. The sub-wear mechanisms during the friction process were microploughing and microcutting. The hardness and toughness of Fe55+1.5 wt% SiC+0.01wt% CeO2 were well-matched, avoiding excessive microcutting and microplastic deformation.

Positioning based on wireless signals such as mobile communication networks has become an important means to provide high-precision location services in environments where satellite signals are blocked. In complex environments such as indoor and underground, wireless signal propagation is obstructed and non-line-of-sight (NLOS) phenomena appears due to serious occlusion and reflection. The time delay caused by NLOS effects has little impact on communication system but can significantly increase positioning errors in positioning systems. Therefore, effective suppression of NLOS errors is crucial to improving 5G positioning accuracy. To address the insufficient feature extraction of existing NLOS error suppression methods, the neglect of residual NLOS measurement errors, and poor stability of position estimation results, this paper innovatively proposes a NLOS mitigation and location estimation method for 5G positioning terminals. Simulation and experimental test results demonstrate that the proposed method outperforms the comparative methods both theoretically and practically, achieving an average positioning accuracy of 1.85 meters in complex indoor NLOS environments. The method proposed in this paper provides a new strategy for NLOS error suppression in indoor 5G positioning, which can significantly contribute to high-precision location services based on commercial 5G networks.

One of the industries with the fastest rate of growth is healthcare, and this industry's enormous data requires extensive cloud storage. The cloud may offer some protection, but there is no assurance that data owners can rely on it for refuge and privacy amenities. Therefore, it is essential to offer security and privacy protection. Increased customer satisfaction with security and privacy preservation is crucial since healthcare big data and its sources are stored in the cloud and contain increasingly private and sensitive information. However, maintaining privacy and security in an untrusted green cloud environment is difficult, thus the data owner should have complete data control. A new work SecPri-BGMPOP(security and privacy of Boost graph Convolutional Network -Pinpointing-Optimization Performance) is suggested that can offer a solution that involves several different steps in order to handle the numerous problems relating to security and protecting privacy. Initially Boost Graph Convolutional Network Clustering (BGCNC) algorithm, which reduces computational complexity in terms of time and memory measurements, is first applied to the input dataset to begin the clustering process. Second, enlarge by employing a piece of the magnifying bit string to generate a safe key, pinpointing based encryption avoids amplify leakage even if a rival or attacker decrypts the key or asymmetric encryption. Finally, to determine the accuracy of the method, an optimal key was created using a meta-heuristic algorithmic framework called Hybrid fragment horde bland lobo Optimization (HFHBLO). Our proposed method currently kept in a cloud environment, allowing analytics users to utilize it without risking their privacy or security.

As the natural resources are getting exhausted, the concept of sustainable development of region has received increasing attentions, especially for resource-dependent cities. In this paper an innovative method that emergy analysis and IPAT (Human Impact Population Affluence Technology) model were combined in order to analyze the quantitative relationship of economic growth and energy consumption and further to evaluate its overall sustainability level. Taiyuan, a traditional, resource-dependent city in China, is selected as the case study region. The main results show that total emergy of Taiyuan increased from 9.023× 1023 sej in 2007 to 9.116× 1023sej in 2014, with 38% reduction on non-renewable emergy and 125% growth on imported emergy. Regional emergy money ratio (RMB) was reduced by 48% from 5.31× 1013sej/$ in 2007 to 2.74× 1013sej/$ in 2014, indicating that the increasing speed of consuming resources and energy was faster than the increase of GDP, and that Taiyuan’s money purchasing power declined. The lower emergy sustainability index (ESI) indicates that Taiyuan was explored and produced large quantities of mineral resources, which puts more stress on the environment as a consequence, and that this is not sustainable in the long run. The IPAT analysis demonstrates that Taiyuan sticks to the efforts of energy conservation and environmental protection, in order to promote regional sustainable development, it is necessary to take an integrated effort. Policy insights suggest that resourceful regions should improve include energy and resource efficiency, optimizing energy and resourceful structure.

Jacobian theta function identities are related to the Addition formula for the Weierstrass 1 Sigma function. In this paper, from the Addition formula for Weierstrass Sigma function, new and 2 simple proofs of four square sums theorem are given. Using the addition formula of the theta func- 3 tions, we also give simple proofs of two square sums and eight square sums theorem.

Mass hauling operations play central roles in construction projects. They typically use many haulers that consume large amounts of energy and emit significant quantities of CO₂. However, practical methods for estimating the energy consumption and CO₂ emissions of such operations during project planning are lacking. This paper presents a detailed model for estimating the energy consumption and CO₂ emissions of mass haulers that integrates the mass hauling plan with a set of predictive equations. The mass hauling plan is generated using a planning program such as DynaRoad in conjunction with data on the productivity of selected haulers and the amount of material to be hauled during cutting, filling, borrowing, and disposal operations. This plan is then used as input for estimating the energy consumption and CO₂ emissions of the selected hauling fleet. The proposed model will help planners to assess the energy and environmental performance of mass hauling plans, and to select hauler and fleet configurations that will minimize these quantities. The model was applied in a case study, demonstrating that it can reliably predict energy consumption, CO₂ emissions, and hauler productivity as functions of the hauling distance for individual haulers and entire hauling fleets.

The Internet of Things (IoT) is a concept based on the integration of various devices and methods of communication to exchange information in order to contribute to the improvement of everyday life, business and environment. This paper focuses on the establishment of a modern Internet of Things platform to ensure secure collection, processing and storage of data, under unexpected events. This platform establishes reliable connectivity which enhance system uptime; the key to success when implementing an IoT strategy. For this purpose, we proposed a hybrid approach combining different connectivity technologies to ensure the availability and smooth operation of the system and the prevention of data loss in unforeseen cases.

In recent decades, with the ever-growing scale of video data, near-duplicate videos continue to emerge. Data quality issue caused by near-duplicate videos is becoming more and more prominent, which has affected the application of normal videos. Although current studies on near-duplicate video detection can be helpful to uncover data quality issues for videos, they still lack a process of automatic merging for the video data represented by high-dimensional features, which are difficult to automatically clean the near-duplicate videos to improve data quality for video datasets. At present, there are few studies on near-duplicate video data cleaning. The existing studies have the sensitive problems of video data orderliness and clustering initial center under a condition that prior distribution is unknown, which seriously affect the accuracy of near-duplicate video data cleaning. To address the above issues, an automatic near-duplicate video data cleaning method based on a consistent feature hash ring is proposed in this paper. First, a residual network with convolutional block attention modules, a long short-term memory deep network, and an attention model are integrated to construct an RCLA deep network with the multi-headed attention mechanism to extract spatiotemporal features of video data. Then, a consistent feature hash ring is constructed, which can effectively alleviate the sensitivity of video data orderliness while providing a condition of near-duplicate video merging. To reduce the sensitivity of the initial cluster centers to results of near-duplicate video cleansing, an optimized feature distance-means clustering algorithm is constructed by utilizing a mountain peak function on a consistent feature hash ring, which can implement automatic cleaning of near-duplicate video data. Finally, experiments are conducted based on a commonly used dataset named CC_WEB_VIDEO and a coal mining video dataset. Compared with some existing works, simulation results demonstrate that the performance of the proposed method.

Pedestrian Dead Reckoning (PDR) is a promising algorithm for indoor positioning. However, the accuracy of PDR degrades due to the accumulated error, especially in multi-floor buildings. This paper introduces a three-dimensional (3D) positioning method based on terrain feature matching to reduce the influence of accumulated error in multi-floor scene. The proposed method involves two steps: motion pattern recognition and position matching calibration. The motion pattern recognition aims to detect different motion states, i.e., taking the stairs or horizontal walking, from the streaming data. Then, stair entrances and corridor corners are matched with transition points of motion states and pedestrian turning points, respectively. After matching, calibration is performed to eliminate the accumulated errors. By carrying out experiments on a two-floor closed-loop path with a walking distance about 145 m, it is shown that this method can effectively reduce the accumulated error of PDR , achieving accurate 3D positioning . The average error is reduced from 6.60 m to 1.83 m.

Objective: The aim of this study was to optimize the fermentation process of Radix Ranunculi ternate via microbial fermentation and analyze the changes in the contents of the main components, the antioxidant and hypoglycemic capacities of the extract before and after fermentation. Methods: The solid-state fermentation process was optimized using single-factor tests and the response surface method, with the yield of the alcohol extract of R. ternate as an evaluation index. Results: The best fermentation process was optimized using solid-state endophytic fungus fermentation technology as follows: strain addition ratio of Chaetomium globosum/Fusarium equiseti =1:1, fermentation for 5 d, sieve size of 40 mesh, liquid/material ratio of 0.8:1 mL·g−1, fermentation temperature of 31 °C, and inoculation amount of 7.5%. Under the optimized conditions, the contents of the water-soluble extract and total polysaccharides decreased by 12.71% and 12.95%, respectively, in the fermentation, The contents of ethanol-soluble-extract, flavonoids, saponins, polyphenols, organic acids, and total amino acids of fermented R. ternate increased by 19.77%, 57.14%, 79.67%, 14.29%, 17.63% and 3.82%, respectively, and the scavenging rate for DPPH, ABTS+, ·OH free radicals and inhibitory rate for α-amylase also increased by 19.02%, 14.17%, 7.53% and 34.54%, respectively, compared with unfermented R. ternate. Conclusions: Solid-state fermentation opens new avenues for the development and application of R. ternate as natural antioxidant and hypoglycemic food.

Starting from acid chlorides, alkynes, tryptamines, and acroyl chloride, 21 densely substituted tetrahydro-beta-carbolines are prepared in a four-component one-pot reaction. In this study, the aza-Michael addition step to generate intermediate enaminones is optimized in the presence of ytterbium triflate. Moreover, apart from acroyl chloride, all reactants can be deployed in almost equimolar ratios, which increases the atom economy of the sequence. For mechanistic rationali-zation, the concluding aza-anellation was investigated by DFT calculations on potential inter-mediates and corresponding activation energies, revealing that the aza-anellation rather pro-ceeds via ene-reaction than via electrocyclization.

Fire detection from satellite sensors relies on an accurate estimation of the unperturbed state of a target pixel, from which an anomaly can be isolated. Methods for estimating the radiation budget of a pixel without fire depend upon training data derived from the location's recent history of brightness temperature variation over the diurnal cycle, which can be vulnerable to cloud contamination and the effects of weather. This study proposes a new method that utilises the common solar budget found at a given latitude in conjunction with an area's local solar time to aggregate a broad-area training dataset, which can be used to model the expected diurnal temperature cycle of a location. This training data is then used in a temperature fitting process with the measured brightness temperatures in a pixel, and compared to pixel-derived training data and contextual methods of background temperature determination. Results of this study show similar accuracy between clear-sky medium wave infrared upwelling radiation and the diurnal temperature cycle estimation compared to previous methods, with demonstrable improvements in processing time and training data availability. This method can be used in conjunction with brightness temperature thresholds to provide a baseline for upwelling radiation, from which positive thermal anomalies such as fire can be isolated.

This study proposes an innovative pharmacovigilance approach, VIGI-4, leveraging ChatGPT Teams Pro version. Our method involves aggregating data from all phase 4 studies published in February 2024 to identify adverse reactions. These results are categorized by disease state alphabetically, demonstrating the method's capacity to generate structured and easily navigable outputs. The results section is tailored to exemplify the valuable, actionable insights attainable through our workflow. This research emphasizes the game-changing potential of integrating advanced technologies such as ChatGPT into pharmacovigilance, signaling a new era in safeguarding drug safety.

Driving factors of smart city construction are exploratively studied by grounded theory method based on text sources from journal papers in SCI and CSSCI databases. Initial scale of driving factors about smart city construction is obtained on the basis of above analyses. This paper modifies measuring items of the initial scale with a small sample pretest and reliability test, then forms final items by exploratory factor analysis. According to the above scale, questionnaires are designed to obtain empirical data, and confirmatory factor analysis is used to verify further validity and reliability of the scale. The results show that driving factors of smart city construction include three main dimensions: problem-oriented factors, business- or technology-driven factors and endogenous development requirements.

The River Habitat Survey (RHS) is a method for assessing the conditions of a river channel and valley, taking into account hydromorphological factors, and assessing the degree of naturalness or the degree of anthropogenic alteration within the channel and valley based on physical and landscape data. The hypothesis tested in this study was that the quality of river habitats demonstrated using the RHS should translate into the composition of their fauna. We investigated aquatic bugs (Heteroptera Aquatica), which are a group with considerable dispersal abilities and, at the same time, composed of stenotopic species associated with a particular environment as well as of eurytopic elements inhabiting a wide range of environments (REF). The research was carried out in a small lowland river, the River Krąpiel (north-western Poland) at 6 sites with 43 sub-sites included. Our analyses suggest the RHS method can predict the composition and quality of the aquatic bug fauna inhabiting a given river. Indicators of river habitat quality (HQA and RHQ) will be associated with different habitat types depending on the geographic location and type of river, once indicating habitats associated with the mainstream river and mineral substrate (mountain and small lowland rivers) and at other times habitats covered by vegetation with relatively slow water flow (large and medium lowland rivers). Therefore, RHS may be a good method for estimating the water bug fauna, linking it to the size and character of the river.

There are rich proper noun derivative semantic relationships in geographic entity vector data. The identification of traditional proper noun derivative semantic relationships usually requires toponym researchers to examine the source of derived toponyms by consulting a large number of toponym documents. This method cannot adapt to the mining of proper noun derivative semantic relationships for large-scale geographical entity. In this regard, this paper proposes a method of identifying the proper noun derivative semantic relationships for geographical entity by combining prompt learning and XGBoost model. This method transforms the extraction problem of proper noun derivative semantic relationships into a binary classification problem by analyzing the characteristics of the derivation relationship of toponyms in the form of toponyms and the spatial and temporal distribution of geography. Firstly, prompt learning and gaussian mixture model are used to extract and cluster the derivation words of toponyms, so as to realize the recognition of derived toponyms collections. Then, enumerate the possible proper noun derivations in the toponym set, and then the XGBoost model is used to identify the semantic relations derived from the proper noun of geographical entities. In the experiment, the recognition method of proper noun derivative semantic relationships based on prompt learning and XGBoost proposed in this paper has achieved good relationship recognition effect in the experiment. This method has certain practical value in the fields of toponym management and toponym translation.

The manufacturing parameters influence the properties of thermo-mechanically processed met-als such as Mg alloys. This paper presents how the mechanical properties, the microstructure and the degradation rate of extruded Mn-containing Mg-Gd-alloys can be modified. Gd as repre-sented REE-element is particularly interesting due to the influence on the texture development in Mg and therefore studied as a base alloy system. The contents of Gd were investigated be-tween 2 to 9 wt.% with Mn-addition of 0.5 and 1.0 wt.%. The grain sizes and the corresponding textures were modified by the extrusion parameters and the alloy content. It was shown that modification by Mn can decrease the grain size, but increase the degree of recrystallization and decrease the degradation rate in the biological medium compared to the binary Mg-Gd system from previous studies. The results suggest that the binary Mg-Gd system can be produced more efficiently by adding Mn and that the resulting properties are more robust.

In typical Cobalt-chromium (CoCr) alloys powders, aluminum oxide (Al₂O₃) powder can be added. In the present study, we successfully prepared alloyed samples of various powder ratios by laser cladding, and analyzed their microstructure and carbide structural characteristics, including microhardness, biological properties, morphology (using scanning electron microscopy), and crystal structure (using X-ray powder diffraction). Elemental distribution was also determined by energy-dispersive X-ray spectral analysis. The results showed that Al₂O₃ addition caused the alloy to change from slender columnar crystals to columnar grains similar, to equiaxed grains. In addition, Al₂O₃ agglomeration zones appeared, and carbide structures were altered. The mechanism of the observed performance changes was also analyzed.

By using Modified simple equation method, we study the Cahn Allen equation which arises in many scientific applications such as mathematical biology, quantum mechanics and plasma physics. As a result, the existence of solitary wave solutions of the Cahn Allen equation is obtained. Exact explicit solutions interms of hyperbolic solutions of the associated Cahn Allen equation are characterized with some free parameters. Finally, the variety of structure and graphical representation make the dynamics of the equations visible and provides the mathematical foundation in mathematical biology, quantum mechanics and plasma physics.

An addition sequence is an important operation in many applications of computer science, such as multi-modular exponentiation and outsourcing protocols. Finding an addition sequence for a set of positive integers with the shortest length is challenging due to the high computational time required to find the solution. In this paper, a new metaheuristic algorithm is designed based on the simulated annealing strategy to generate a short addition sequence. The efficiency of the proposed algorithm was proved experimentally by comparing it with the previous exact and heuristic algorithms in terms of running time and the length of the addition sequence.

The main goal of this study was to introduce glycerol as a plasticizer to Polyvinyl Alcohol (PVA) membranes in order to increase their flexibility. The qualities of PVA membranes produced with various glycerol concentrations were evaluated. With the modified PVA membranes containing 5% glycerol, encouraging results were obtained. These membranes had superb optical characteristics and a 90% transmittance rate. This shows that the membranes are suited for applications needing excellent optical clarity since they permit light to travel through with little distortion. Importantly, FTIR analysis demonstrated that the addition of glycerol had no effect on the PVA membranes' chemical composition or structural integrity. In comparison to pure PVA Membrane, the modified membranes' water barrier qualities showed a considerable drop of up to 50%. The membranes are useful for applications requiring moisture management or breathability because of the decline, which points to an increase in permeability to water vapour. The large increase in flexibility, which was achieved by the PVA membranes containing 5% glycerol and beyond the brittleness typically associated with pure PVA, was a noteworthy discovery. The possible applications are expanded due to the increased flexibility, especially in industries where adaptability and flexibility are essential. Additionally, the addition of glycerol improved the thermal stability of the membranes, as they showed increased resistance to breakdown or decomposition at high temperatures. Additionally, the modified membranes' mechanical qualities were better than those of pure PVA, indicating that the glycerol addition improved their overall mechanical performance and tensile strength. PVA membranes were effectively made more flexible by adding 5% glycerol as a plasticizer. This led to membranes with superior optical qualities, reduced water barrier properties, greater flexibility, improved thermal stability, and maybe improved mechanical capabilities. These discoveries open up new opportunities for the use of these flexible PVA membranes in a range of settings, such as flexible packaging, biomedical materials, and other industries that need adaptive and flexible materials.

A co-curing resin system consisting of 9368 epoxy resin for prepreg and 6808 epoxy resin for resin transfer molding (RTM) was developed. A corresponding preparation method of novel polymer composite bolted T-joint with internal skeleton and external skin was proposed based on prepreg-RTM co-curing process, and novel T-joints were fabricated. A series of conventional configuration T-joints based on RTM process and T-joints made of 2A12 aluminum alloy were prepared simultaneously. Bending performances were studied on these T-joints experimentally. The results indicate that 9368 epoxy resin and 6808 epoxy resin exhibit good compatibility in rheological and thermophysical properties. The novel T-joints prepared with prepreg-RTM co-curing process show no obvious fiber local winding or resin-rich regions inside, and the interface quality between internal skeleton and external skin is excellent. The main failure modes of the novel T-joint under bending load include separation of skin and skeleton and fracture along the thickness on the base panel; the skeleton carries the main bending load, but there is still load transfer between external skin and internal skeleton through their interface. The internal damages of the novel T-joint are highly consistent with surface damages observed visually, facilitating the detection and timely discovery of damages. The initial stiffness, damage initiation load, and ultimate load of the novel T-joint are 1.65 times, 5.89 times, and 3.45 times that of conventional T-joint, respectively. When considering the influence of density, the relative initial stiffness and relative ultimate load of the novel T-joint are 1.44 times and 2.07 times that of aluminum alloy T-joint, respectively.

Water networks are critical infrastructure components, ensuring the continuous supply of high-quality drinking water to consumers. To secure such water supply, regular maintenance, including the replacement of deteriorating pipelines, is essential. In this study, a methodology has been developed for determining optimal pipeline replacement solutions in water supply systems at water utilities with limited data availability. Hydraulic analysis has been conducted on the segment of 25 km of the water supply network using the free software EPANET. Applying water network optimization, eight pipeline replacement projects according to 13 pre-defined criteria have been identified and evaluated. The paper outlines the methods for evaluating the criteria, including defining specific quantitative limits. The Analytical Hierarchical Process (AHP) method was used in the paper to determine the weights of the criteria. The reason for applying this method refers to problems that involve a set of criteria with a mixed structure, including both quantitative and qualitative aspects. Also, the paper describes the steps of the multi-criteria optimization method VIKOR, used to select the optimal project. This paper, considered as case studie, describes a method, i.e. application of a new principles and an innovative way to solve a problem for developing countries.

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

The aim of this study was to develop a ready-to-eat vegetable-herb mixes with high nutritional and sensory values, as well as good storability. In this regard the suitability of fresh herbs (peppermint, oregano, green basil, red basil, and parsley) was tested for use in mixes with fresh-cut iceberg lettuce. Lettuce-herb mixtures were stored for 6 days at 5°C. The reason for the decrease in the appearance of the salads was the browning of the cut surface of the lettuce, as well as discoloration on the cut herbs. Comparing the storage ability of cut herbs, red basil and parsley retained the best appearance for 6 d at 5 °C. A small addition of herbs to fresh-cut iceberg lettuce caused a significant increase in contents of pro-health ingredients in the mixes. There were large discrepancies in the sensory quality of the mixes, but the highest quality and consumer acceptance were found for salads with parsley (5% and 10%) and red basil (5%). After harvest, the fresh herbs were more contaminated by molds than the iceberg lettuce. Bacterial, yeast and mold contamination increased during storage, but the rate of mold growth was much lower in the mixes with parsley compared to lettuce alone.

In this study, the effects of various beryllium (Be) addition (Be-free, 0.1, 0.25, 0.50 wt.%) on the microstructure, mechanical properties, and corrosion corrosion of the Al-Mg-Li alloys were systematically investigated. The best performance was obtained in alloy with 0.1 wt.% Be addition. Trace Be addition promotes the grain refinement of the as-cast alloy ingot and contributes positive effects to the recrystallization, bringing improvement of tensile property. Meanwhile, the best anti-corrosion behavior is also presented at 0.1 wt.% Be addition, due to its potential to reduce the width of precipitates free zone (PFZ). As the Be content increase to an excessive level, the comprehensive performance decreases. Therefore, it is strongly recommended that adding trace Be element into Al-Mg-Li alloys has a positive effect on the comprehensive service performance.

Fresh potatoes were deep-fried in olive oil (OO) & extra virgin olive oil (EVOO) and their blends with 5%, 10% and 20% v/v sesame oil (SO). This is the first report on the use of sesame oil as natural source of antioxidant for olive oil deep-frying. Oil was evaluated for Peroxide Value (PV), Free Fatty Acids (FFA), K₂₃₂, K₂₇₀, Trolox Equivalent Antioxidant Capacity (TEAC) and Total Phenols (TP) until Total Polar Compounds (TPCs) reached 25%. Sesame lignan transformations were monitored through Reverse-phase HPLC. While TPCs in olive oils increased at a steady rate, the addition of 5%, 10% and 20% v/v SO created a time window lasting 1, 2 and 3 hours, respectively, where TPCs were constant. SO addition to OO increased the total frying time. Furthermore, the addition of SO reduced the peroxides formation rate for both OO and EVOO. EVOO was more resistant to oxidation than OO as measured by TPCs and TEAC, while frying time raised from 21.5 to 25.25 h when EVOO replaced OO. The increase in frying time for olive oil but not for extra virgin olive oil, after SO addition, is pointing out a niche market for extra virgin olive oil in deep-frying.

Hydrogenated small fullerenes (Cn, n<60) are of interest as potential astrochemical species, and as intermediates in hydrogen catalysed fullerene growth. However computational identification of key stable species is difficult due to the vast combinatorial space of structures. In this study we explore routes to predict stable hydrogenated small fullerenes. We show that neither local fullerene geometry nor local electronic structure analysis are able to correctly predict subsequent low energy hydrogenation sites, and indeed sequential stable addition searches also sometimes fail to identify most stable hydrogenated fullerene isomers. Of the empirical and semi-empirical methods tested, GFN2-xTB consistently gives highly accurate energy correlation (r>0.99) to full DFT-LDA calculations at a fraction of the computational cost. This allows identification of the most stable hydrogenated fullerenes up to 4H for four fullerenes, namely two isomers of C28 and C40, via “brute force” systematic testing of all symmetry inequivalent combinations. The approach shows promise for wider systematic studies of smaller hydrogenated fullerenes.

The presence of antibiotic residues in honey has recently become a growing public health concern due to the overuse of these products in beekeeping and their transfer to the food industry. The aim of this study was to develop and validate a simple, selective and sensitive method for the simultaneous identification and quantification of residues of twenty-two sulfonamides, trimethoprim and dapsone in honey using a rapid and reliable liquid chromatography–tandem mass spectrometry (LC–MS/MS) method. The developed method showed good linearity, specificity, precision (repeatability and intra-laboratory reproducibility) and recovery. The decision limit (CCalpha) ranged between 2.16-22.12 µg/kg for CCα, while the detection capability (CCbeta) was between 2.16- 2.67-27.36 µg/kg. The method proved to be rapid, reliable and effective for the determination of sulfonamides, trimethoprim and dapsone from honey samples. The average recoveries were estimated to be between 70 and 106%. The relative standard deviations (RSDs) were between 6-18%. In practice, the method is essential to check the honey sold on the market and ensure its safety before it reaches the consumer.

Based on the Flashing Ratchet Potential (FRP) and Electro-Spectroscopy detection techniques, a new detection method was experimentally examined. This method allows the detection of sub-micro particles in the human exhaled air such as viral particles and other biological agents. The detection signal created by this method is carried out by electron current buildup forming an Electric Current-Spectrum (ECS) distinguishing the contents of the exhaled air samples. The detection method was developed based on FRP and a beam of free charges passing through the electrodes of the FRP. The ECS is characterized by low-energy free charges interacting with the medium through which they pass, where numerous free charges are scattered (delayed) as a result of these interactions. The resulting ECS is characterized by FRP's capacity to drift back the delayed free charges to their original starting positions. By comparing the ECS of two exhale air samples, this new technology can be utilized to identify the presence of viral and microorganisms’ particles. The time-escalating ECS difference quickly indicates the presence of such particles. Moreover, the FRP's optimal operating settings was experimentally defined, in addition to the experimental evaluation of its functionality to confirm the FRP's promising sensing capabilities, which were statistically examined several times to ensure the reproducibility of the results.

The topic of modification of magnesium oxychloride cement (MOC) via specific functional additives is very much pronounced in the research of alternative building materials. This study deals with the co-doping of MOC by 1D and 2D carbon nanomaterials in order to improve its mechanical properties while using tannic acid (TA) as a surfactant. Furthermore, the effect of TA on MOC also covers the improvement of water resistance. As a filler, three size fractions of standard quartz sand are used. The proposed types of MOC-based composites show promising results considering their mechanical, macro- and microstructural, chemical, and hygric properties. The use of 1D and 2D nanoadditives and their mixture enables the improvement of the flexural strength and most of all softening coefficient, the durability parameter characterizing the resistance of the prepared materials to water. For samples immersed in water for 24 h, the compressive strength of all modified composites tested was higher than that of the reference composite. Quantitatively, the developed co-doped composite shows mechanical parameters comparable to or even better than those of commonly used Portland cement-based materials, while maintaining high environmental efficiency. This indicates its potential use as an environmentally friendly alternative to Portland cement-based products.

For this research, a comparative evaluation was performed in which the addition of 3D-printed biocarriers fabricated with 13X and Halloysite (13Χ-Η) and commercial Kaldnes K1 biocarriers were evaluated as opposed to the non addition of biocarriers in a semi-pilot scale MBBR-MBR unit. For the evaluation of the MBBR-MBR efficiency, various physicochemical parameters were measured while static light scattering and optical microscopy observations were additionally used. Biofilm extracted from the biocarriers was also evaluated. It was observed that in the MBBR-MBR K1 unit, the membrane filtration improved while in the MBBR-MBR 13X-H unit the membrane fouling rate was the same as in the control MBBR-MBR unit. This is due to the production of large amount of SMP which resulted from the large amount of biofilm created in the 13X-H biocarriers. An optimal biodegradation of the organic load was concluded for all three MBBR-MBR units. The nitrification and denitrification processes were improved at the MBBR-MBR units using 13X-H and K1. The dry mass produced on the 13X-H biocarriers was three orders of magnitude larger than that produced on the K1. Finally, it was observed that mostly EPS was produced in the biofilm of K1 biocarriers while in the biofilm of 13X-H mostly SMP.

Acute and chronic graft versus host disease (a/cGVHD) are major complications of allogeneic stem cell transplantation and a frequent cause of non relapse-mortality. The treatment of a/cGVHD consists of steroid administration at full dose. In the case of aGVHD, around 60 % of patients with grade III/IV fails to respond (steroid-resistant, SR), requiring a second line therapy. Extracorporeal photopheresis (ECP) represents a good option for second line treatment, leading to multiorgan response in several patients. Here, we have evaluated the performances of a cytofluorimetric quality control of the first ECP procedure in 29 patients with severe SR aGVHD who underwent ECP. The quality control represents a check control of in vitro cell apoptosis/death induction in collected and irradiated CD3+ cells by ECP. Our analysis shows that in more than 70 % quality controls a relevant apoptotosis/death of CD3+ cells was observed after cell irradiation, as compared to non-irradiated controls. Albeit observed in a small patients’ series, the occurrence of relevant in vitro effect after ECP relates to less procedures and/or to a better survival on ECP. Age, disease, gender, aGVHD grade and time from transplant to the first ECP had not impact on ECP efficacy in this patients’ series.

Robotic systems have been widely used in various industries, so the security of communication between robots and their components has become an issue that needs to be focused on. As a framework for developing robotic systems, the security of ROS2 can directly affect the security of the upper-level robotic systems. Therefore, it is a worthwhile research topic to detect and analyze the security of ROS2. In this paper, we adopt a formal approach to analyze the security of the communication mechanism of ROS2. First, we use a state transition system to model the potential vulnerabilities of ROS2 based on the ROS2 communication mechanism and the basic process of penetration testing. Secondly, we introduce the CIA model on the basis of the established vulnerability model and use LTL to define its security properties. Then, we design and implement a vulnerability detection tool for ROS2 applications based on the vulnerability model and security properties. Finally, we experimentally test some ROS2-based applications, and the results show that ROS2 has vulnerabilities without additional protection safeguards.

Buckling defect will appear on the outer surface of the deformed ring during constrained ring rolling (CRR) of aluminum alloy thin wall conical ring with inner high ribs (AATWCRIHR), if the geometrical dimension of the ribs doesn't match the wall thickness. To avoid the buckling defect, a quantitative method for characterizing the degree of the buckling defect is proposed using the area of buckling profile. Then an orthogonal experimental scheme was designed taking the width of the middle rib, thickness of wall, and height of the middle rib as design variables and defining the area of buckling profile as optimization objective. Subsequently, a quadratic polynomial response surface model was established by combining the optimization algorithm with the finite element method (FEM), and the geometrical dimension of the middle ribs of the deformed AATWCRIHR is optimized. Also the optimal parameter combination to minimize the area of buckling profile is obtained and verified using FE simulation. Results show that the AATWCRIHR after optimization doesn’t generate the buckling defect during constrained ring rolling, and it is proved that the quantitative buckling defect representation method and the optimization design method based on the response surface model and the finite element simulation results are feasible for the constrained ring rolling process of the AATWCRIHR.

In this paper, we compile the fractional power series method and the Laplace transform to design a new algorithm for solving the fractional Volterra integro-differential equation. For that, we assume the Laplace power series (LPS) solution in terms of power q=1m,m∈Z+, where the fractional derivative of order α=qγ for which γ∈Z+. This assumption will help us to write the integral, the kernel, and the nonhomogeneous terms as a LPS with the same power. The recurrence relations for finding the series coefficients can be constructed using this form. To demonstrate the algorithm's accuracy, the residual error is defined and calculated for several values of the fractional derivative. Two strongly nonlinear examples are discussed to provide the efficiency of the algorithm. The algorithm gains powerful results for this kind of problem. Under Caputo meaning the obtained results are illustrated numerically, and graphically. Geometrically, the behavior of the solution declares that the changing of the fractional derivative parameter values' in their domain alters the style of the attained solution in a symmetrical meaning and fully coinciding to the ordinary derivative value'. From these simulations, the results report that the recommended novel algorithm is a straightforward, accurate, and superb tool to generate analytic-approximate solutions for Integral, and integro-differental equations of fractional order.

Polydimethylsiloxane with hydroxy groups was functionalized to form functionalized polydimethylsiloxane, which subsequently underwent an addition reaction with isophorone diisocyanate to form the prepolymer. Next, 3-aminopropyltriethoxysilane (APTS) reacted with 3-glycidoxypropyltrimethoxysilane (GPTS) to produce bridged polysilsesquioxanes, and the sol–gel technology was employed to form hyperbranched polysiloxane nanoparticles with hydroxy groups, which was used as the additive. The hyperbranched polysiloxane and the prepolymer containing NCO functional groups then underwent an addition reaction to produce the hybrid materials. Fourier-transform infrared spectroscopy and 29Si nuclear magnetic resonance were used to characterize the structure of the polyurethane hybrid. Regarding thermal stability, after the hyperbranched polysiloxane nanoparticles was introduced, the integral procedural decomposition temperature increased from 348 ºC for polyurethane matrix to 859 ºC for the hybrid material. The results revealed that the thermal stability of the hybrid material substantially increased by approximately 247%.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

A enantioselective tandem transformation concerning asymmetric allylic decarboxylative addition and cyclization of N-nosylimines with vinylethylene carbonates (VECs) in the presence of [Rh(C2H4)2Cl]2, chiral sulfoxide-N-olefin tridentate ligand has been developed. The reaction of VECs with various substituted N-nosylimines proceeded smoothly under mild conditions, giving highly functionalized oxazolidine frameworks in good to high yields with good to excellent enantioselectivity.

Compared to tin lead alloys, lead-free tin alloys have lower toxicity, making them more widely used. In this study, Sn-20Bi-0.3Al-xY solders alloys were prepared. The effects of the addition of Y on its microstructure, micro-hardness, wettability and mechanical properties was investigated. The result showed that the addition of Y had significant effect on the refinement of Sn-20Bi-0.3Al-xY. From the spreading tests results, Y increased the wettability of the solders, however when the fraction of Y gradually increased, the wettability reduced. The ultimate tensile and hardness of Sn-20Bi-0.3Al-xY solders alloys were increased as the content of Y increasing.

Soil is an extremely significant resource for human survival, and agglomerates, as the basic unit of soil structure, not only enhance soil fertility and control the biological validity of nutrients, but also strengthen the soil's erosion resistance. The mass application of fertilizers may have a significant impact on crop growth and soil structure, and the rational application and dispensing of fertilizers will be an urgent issue to be addressed. Therefore, the effect of fertilizer application on the stability of water-stable soil aggregates needs to be studied under different meteorological and soil conditions to draw more general and feasible conclusions. Our Meta-analysis of data from 220 of 56 published studies found that fertilizer application increased mean weight diameter (MWD) by an average of 18% compared to the no-fertilizer treatment. Among the nitrogen (N), phosphate (P), and organic (OM) fertilizer treatments, the organic fertilizer treatment had a greater stimulatory effect on MWD (26%). Among the different fertilizer levels, low level of phosphorus (<40kg·hm-2·yr-1), high level of N (>120kg·hm-2·yr-1), and low level of organic fertilizer (<5000kg·hm-2·yr-1) increased MWD by 19%, 14%, and 41% respectively. Across soil types and land use types, the response to MWD was positive for red soils and paddy fields, and the stimulatory effect of organic fertilizer was more significant compared to chemical fertilizer. The regression model showed that the response ratio of MWD was negatively correlated with the response ratio of soil pH and bulk density (BD), and positively correlated with the response ratio of soil organic carbon (SOC) and microbial mass carbon (MBC). Meanwhile, the PLS-SEM model showed that average annual temperature was the main factor affecting the stability of soil aggregates, and the average annual rainfall is the secondary factor. Therefore, this study found that the long-term use of organic fertilizers in place of some chemical fertilizers was more effective than chemical fertilizer alone. Temperature and rainfall have greater effects on the response of fertilizer to soil aggregate stability.

The narrow process window during intercritical annealing and discontinuous yielding have limited the commercialisation of medium Mn steels. In this study, a double annealing process based on the commercial continuous annealing line is proposed. The cold-rolled medium Mn steels were first fully austenitized and quenched during the first annealing, followed by the intercritical annealing for reverted austenite transformation. The microstructure of duplex lath-shaped austenite and ferrite is produced and the steel exhibit a desirable continuous yielding during tensile deformation. Al is added into the medium Mn steel to enlarge the process window and to improve partitioning efficiency of Mn. The produced steel is more robust with temperature fluctuation during the industrial process due to the enlarged intercritical region. Mn partitioning is more efficient owing to elevated annealing temperature, which results in the improvement of ductility in the Al-added steel with increased austenite stability.

Optimizing the nitrogen (N) timings and rate can improve nutrient uptake, and nutrient-efficiencies, especially of N in wheat under the changing climate scenario. Climatic stress in the form of high temperature and drought resulted in the decreased crop physiology and, ultimately, grain yield. Taking the example of rainfed wheat, we quantified the impact of N application rates as full and split-dose at three variable sites of rainfed Pothwar, Pakistan by conducting field experiments for two years (2013-14 and 201-15). Treatments include, T₁ = Control (No fertilizer applied), full dose of N applied at the time of crop sowing, i.e. T₂ = 50 kg N ha^-1, T₃ = 100 kg N ha^-1 and T₄ = 150 kg N ha^-1 and split application of N at different timings during different stages of the crop called as split application of N, i.e. T₅: Application of 50 kg N ha^-1 (15 kg N ha^-1 (Sowing) : 20 kg N ha^-1 (Tillering) :15 kg N ha^-1 (Anthesis), T₆: Application of 100 kg N ha^-1 (30 kg N ha^-1 (Sowing): 40 kg N ha^-1 (Tillering) : 30 kg N ha^-1 (Anthesis) and T₇: Application of 150 kg N ha^-1(45 kg N ha^-1 (Sowing) : 60 kg N ha^-1 (Tillering) : 45 kg N ha^-1 (Anthesis). Three study sites include viz. Islamabad (High rainfall with optimum temperature), University Research Farm (URF)-Koont (Medium rainfall with moderate temperature), and Talagang (low rainfall with high temperature). Results showed that the highest stomatal conductance (0.80 mole m^-2 sec^-1), net photosynthetic rate (20.07 μmole m^-2s^-1), transpiration rate (9.58 mmole m^-2s^-1), intercellular CO₂ concentration (329.25 μmole CO₂ mol^-1 air), SPAD values (58.86 %) and proline contents (35.42 μg g^-1) were obtained for split application of N (T₆ = Split N₁₀₀) compared to control and full dose of N treatments. Among sites, these physiological traits remained highest at Islamabad and lowest at Talagang, while among years, maximum values of the measured parameters were obtained in 2013-14. A similar trend was observed for crop total N, N efficiencies, and agronomic traits of the crop. Our results suggest that optimum N application rate and its suitable timings can help to harvest real benefits of N as in our findings, split dose resulted in the maximum performance of the crop from physiological parameters to the agronomic traits of the rainfed wheat crop.

The photoreduction of CO2 is an intriguing process, which allows the synthesis of fuels and chemicals. One of the limitations for CO2 photoreduction in the liquid phase is its low solubility in water. This point has been here addressed by designing a fully innovative concept of pressurized photoreactor, allowing operation up to 20 bar and applied to improve the productivity of this very challenging process. The photoreduction of CO2 in the liquid phase was performed using commercial TiO2 (Evonink P25), TiO2 obtained by flame spray pyrolysis (FSP) and gold doped P25 (0.2 wt% Au-P25) in the presence of Na2SO3 as hole scavenger (HS). The different reaction parameters (catalyst concentration, pH and amount of HS) have been addressed. The products in liquid phase were formic acid and formaldehyde. Moreover, for longer reaction time and with total consumption of HS, gas phase products formed (H2 and CO) after accumulation of significant amount of organic compounds in the liquid phase, due to their consecutive photoreforming. Enhanced CO2 solubility in water was achieved by adding a base (pH= 12-14). In basic environment, CO2 formed carbonates which further reduced to formaldehyde and formic acid and consequently formed CO/CO2+H2 in the gas phase through photoreforming. The deposition of small Au nanoparticles (3-5 nm) (NPs) onto TiO2 was found to quantitatively influence the products distribution and increase the selectivity towards gas phase products.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Microwave radiation diagnosis technology can detect thermal changes in skin tissue earlier than anatomical changes, but its detection accuracy is limited by non-target radiation interference in the measurement environment, additional measurement errors of system units, and energy scattering and transmission between skin tissues. This paper aims to address the scientific challenges of analyzing the forward and inversion modelling detection mechanism of layered accurate temperature measurement of human skin tissue based on multi-band. The study focuses on the construction of a pencil beam antenna optimization system, the optimization strategy of high-sensitivity correlated radiometer architecture, and the high-precision multi-band forward and inversion modelling detection algorithm. The key technologies include: (1) A new method of integrated modeling and multi-index optimization of antenna with high directivity and small aperture is proposed, and a priori knowledge-guided neural network of pencil beam distribution is constructed to realize the inversion model of antenna structural parameters; (2) The influence mechanism of high sensitivity correlated radiometer architecture error is analyzed, and a periodic phase shift error correction algorithm based on uniform polar circle is designed; (3) Combining deep learning theory and hyperparameter optimization framework, an iterative model is established, and the objective function modified by the penalty factor is defined to realize a new detection method combining forward and inversion. This paper presents a theoretical foundation for the industrialization of microwave radiation diagnostic technology.

(1) Background: Although diagnostic criteria for massive hemorrhage with organ dysfunction such as disseminated intravascular coagulation associated with delivery have been empirically established based on clinical findings, strict logic has yet to be used to establish numerical criteria. (2) Methods: A dataset of 107 deliveries with ≥2,000 g of blood loss, among 13,368 deliveries from nine national perinatal centers in Japan between 2020 and 2023 was obtained. Twenty-three patients had fibrinogen levels &lt;170 mg/dl, which is the initiation of coagulation system failure per our previous reports. Three of these patients had hematuria. We used six machine learning methods to identify the borderline criteria dividing the fibrinogen/fibrin/fibrinogen degradation product (FDP) planes, using 15 coagulation fibrinolytic factors. (3) Results: The boundaries of hematuria development on a two-dimensional plane of fibrinogen and FDP were obtained. If the FDP–fibrinogen/3–60 (mg/dl) value is positive, this indicates hematuria; otherwise, the case is non-hematuria, as demonstrated by the support vector machine method that seemed the most appropriate. (4) Conclusions: The borderline criterion dividing the fibrinogen/FDP plane for patients with hematuria that could be considered organ dysfunction in massive hemorrhage during delivery was obtained using artificial intelligence, and this method seemed to be useful.

In the present work, diamond films have been grown on GaN-on-Sapphire substrates by chemical vapor deposition (CVD) with the addition of nitrogen to the standard H2/CH4 precursor recipe. Diamond on GaN materials processing is not straight-forward, as GaN is susceptible to a quasi-pure hydrogen CVD plasma etching. 1%, 3% and 5% N2 gas was gradually added to the H2 gas with fixed 6% CH4 in the recipe to promote the growth of diamond nanocrystals. Different types of microstructures were produced, with addition of nitrogen to the precursor gas recipe. Nitrogen gas changes the diamond film microstructure from faceted to spherical grains, with signs of GaN etching. The sp3 bonded diamond film produced by nitrogen addition was found to be co-deposited along with a considerable amount of other non-diamond carbon phases (D - disordered graphite, G - crystalline graphite, TPA - trans-polyacetylene) and qualitatively all the diamond films were 50% pure (Raman peak ratio Isp3 / ID). The FWHM of the sp3 carbon Raman peak was calculated to be 6.5 cm-1, when there was no nitrogen gas in the precursor recipe, which deteriorates to a large extent after successive addition of N2. Fourier transform infrared spectroscopy (FTIR) showed a strong presence of the nitrogen related defects (peak positions at 1190 and 1299 cm-1) inside the nanocrystalline diamond (NCD) films grown with N2 addition. GaN layer etching from the base substrate by the CVD plasma was clearly evidenced by energy dispersive X-ray spectra (EDS) of the deposited films. Al elemental EDS peaks from the base sapphire substrate were observed for the films grown with nitrogen addition, but no Ga EDS peaks were detected. X-ray diffraction (XRD) micrographs further supported the enhanced GaN etching phenomenon. Nitrogen addition was thus found to be detrimental for growing CVD diamond films over GaN surfaces. The electrical resistivity of the uncoated GaN was initially measured to be 22.2 Ω-cm. However, the resistivity rose to 1.59×106 Ω-cm after the nitrogen assisted film deposition; due to the GaN etching - thereby exposing the underlying insulating sapphire substrate.

The cast defects strongly degrade the mechanical properties in cast alloys. The effect of Sn addition on Al-Si alloys was investigated by 3D computed tomography, SEM and TEM. Amorphous Sn oxides are found near the alumina film, cause more shrinkage pores, initiate cracks and deteriorate mechanical properties. This work suggests not adding Sn in various Al alloys used in cast state.

Additives can improve the efficiency of anaerobic digestion by increasing biogas production, reducing air pollution, and preventing total ammoniacal nitrogen (TAN) inhibition. Biological or chemical supplementation can also improve the economic efficiency of anaerobic digestion. However, the effects of specific additives on biogas production can vary depending on the type of supplement used. This research utilizes the additives on an industrial scale and monitors the optimization of the anaerobic digestion operating parameters after their addition. The various AD additives were examined in a sufficient cycle of operation for three biogas plants located in northern Greece. In this manner, the effectiveness was investigated in multiple initial feeds and unstable operating situations caused by the seasonality of specific feedstocks. The existing operation state in the three biogas plants was recorded before and after adding the supplements. In all three cases, lower concentration levels were observed in many of the examined trace elements. Introducing additives proved to be a stabilization factor in AD performance and inhibition mediator.

For order-of-addition experiments, the response is affected by the addition order of the experimental materials. Consequently, the main interest focuses on creating a predictive model and an optimal design for optimizing the response. Van Nostrand (1995) proposed the pairwise-order (PWO) model for detecting PWO effects. Under the PWO model, the full PWO design is optimal under various criteria but is often unaffordable because of the large run size. In this paper, we consider the D-, A- and M.S.-optimal fractional PWO designs. We first present some results on information matrices. Then, a flexible and efficient algorithm is given for generating these optimal PWO designs. Numerical simulation shows that the generated design has an appealing efficiency in comparison with the full PWO design, though with only a small fraction of runs. Several comparisons with existing designs illustrate that the generated designs achieve better efficiencies, and the best PWO designs and some selected 100% efficient PWO designs generated by the new algorithm are reported.

The process of shock wave focusing can make the strength of shock waves be continuously accumulated and turned into detonation wave in Pulse Detonation Engine (PDE). However, its effective application needs the inlet jets be in high temperature and velocity, which is difficult to be satisfied under certain conditions. Therefore, in this paper, metal magnesium assisted detonation initiation is proposed and the effect of magnesium particle addition on the shock wave focusing process in a kerosene-fueled PDE with cavity configuration is investigated through numerical simulation. The result showed that when the temperature of the premixed fuel/air jets injected in opposite direction was set as 650 K, the collision of leading shock waves on the central axis was the main source of energy deposition and the shock wave focusing could make the detonation be initiated in the cavity. When the temperature of jets is reduced to 550 K, fuel ignition and detonation could not be achieved through shock wave focusing. Then adding metal magnesium particles into the combustor made the energy deposition be enhanced and the detonation be induced. The diffusion of metal particles can significantly change the structure, motion, merging and dissipation of vortices in the flow field. Generally, the shock wave focusing process is basically not affected with metal particles injection. Therefore, this method can be successfully employed for detonation initiation in the cavity when the fuel/air premixed jet temperature is not high for PDE.

Thermoplastic molded regenerated silk was proposed as structural material in tissue engineering applications, mainly for application in bone. The protocol allows to obtain a compact non-porous material with a compression modulus in the order of a Giga Pascal starting from silk fibroin by compressing a silk fibroin lyophilized sponge of powder in mold at temperature higher than the glass transition temperature (Tg). The main purpose of the produced resin was the osteofixation and other structural applications in which the lack of porosity was not an issue. In this work, we introduced the use of citric acid in the thermoplastic molding protocol of SF to obtain a porosity inside the structural material. In addition to the previously developed protocols the addition of citric acid allowed us to obtain a structural material. The CA powder during the compression acted as a template for the pore formation. In addition, the CA was able to effectively crosslink the SF chain improving the mechanical strength. This effect was proved both evaluating the compression modulus and by studying the spectra obtained by Fourier infrared spectroscopy (FTIR). This protocol may be applied in the near future to the production of a structural bone scaffold.

Geopolymer is an emerging material alternative to Portland cement and has potential as a refractory material. Adding filler in geopolymer material is a strategy to increase the advantages of its physical and mechanical properties. It has been previously reported that adding nanoparticles can increase the compressive strength value, but there is no reported interaction between nanoparticles and geopolymer during the geopolymerization process. This study aims to study the effect of adding nano-zirconia fillers on the physical and mechanical changes of metakaolin-based geopolymers with nano-zirconia fillers. The geopolymer samples were made with 100 g of metakaolin as the base material and nano-zirconia in amounts of 2 gr, 5 gr, 10 gr, and 15 gr. Further characterization was carried out by XRD, FTIR, and SEM-EDX. This study showed that the compressive strength of the MZr05 sample increased significantly by 58.7% compared to the control sample. The test results of the structure and functional groups did not lead to any new compounds formed in the geopolymerization reaction. Therefore, the interaction of metakaolin geopolymer with nano-zirconia only creates an interfacial bonding.

We apply principles of Gibbs phase plane chemistry to and across the entire ocean-atmospheric interface. Surface tension increments support a two dimensional, tangential pressure well known to determine rates of bulk gas, bubble, salt, spray and momentum transfer plus both sensible and latent heat fluxes. Hence it is worth asking whether tension mapping follows from current understanding of two dimensional composition. A history is provided dating back centuries and demonstrating that detrital organic macromolecules are central; subtle surfactant functional variation creates a microforcing field which dissipates turbulent energy at the sub-meter scale. Since we have just distributed major biopolymeric classes emitted as primary organic aerosol, further climate links can be established by considering full planar thermochemistry. Organic microlayer behaviors are reviewed with attention to confined, analog phase transitions among two dimensional “solid, liquid, (and) gaseous” states serving as elasticity indicators. We also discuss surfactant properties of general marine dissolved organic carbon, demonstrating that only proteins and lipids are capable of occupying significant local micro-area. The literature often suggests albumin and stearic acid as best proxies, and so we distribute their concentrations through multilevel global ecodynamic simulations. Consensus distributions are obtained in order to control adsorptive equilibria. Working from conservation of planar free energy, a parametric equation of state is devised relating excess coverage to the surface pressure-modulus. Constant settings for the proxy pair are drawn from laboratory study, and they successfully reproduce frequencies for surfactant solid-to-gas occurrence in ambient compression experiments. Functionally resolved organic measurements are rare and so we group them into super-ecological province tables showing that our bulk concentration estimates are reasonable. Outputs are then fed into a coverage-tension-elasticity code. Resulting contours traverse the critical range for piston velocity, bubble-spray and damping effects on either a regional or seasonal basis. There is also a possibility for widespread microlayer crystallization in polar seas. The concepts are a direct extension of our organic aerosol work, and the two approaches could be inserted into Earth System Models in tandem. Uncertainties in the logic are enumerated and include kinetic and thermochemical factors at multiple scales. But the problems are reducible through molecular modeling coupled to renewed laboratory and field study. Connections to marine colloids-gels, microlayer iron chelation, and linings of the ice channel network are discussed additionally.

The present study aims to develop an efficient numerical method for computing the diffraction and radiation of water waves with horizontal long cylindrical structures, such as floating breakwaters. A higher-order scheme is used to discretize geometry of the structure as well as the relevant physical quantities. As the kernel of this method, Wehausen’s free-surface Green function is calculated by a newly-developed Gauss-Kronrod adaptive quadrature algorithm after elimination of its Cauchy-type singularities. To improve computational efficiency, a Chebyshev approximation approach is applied to a fast calculation of the Green function that needs evaluation thousands of times. In addition, OpenMP parallel technique is used to the formation of influence coefficient matrix, which significantly reduces CPU time. Finally, computations are performed on wave exciting forces and hydrodynamic coefficients for the long cylindrical structures, either floating or submerged. Comparison with other numerical and analytical methods demonstrates good performance of the present method.

This study investigates the effect of Re addition on the microstructure evolution and oxidation resistance of Co-Cr-Ta-Ti-C alloys. The alloys tested in this study consist of a Co-rich matrix with mixed HCP and FCC phases, together with TaTiC2 and Ti-based carbides. The addition of Re promotes the precipitation and growth of a CoCr-rich σ phase. Differential thermal analysis (DTA) showed that the melting temperatures did not change drastically up to 10 at% Re addition, whereas 15 at% Re addition significantly increased the melting temperature of the alloys. Oxidation tests in air at 1200°C showed that excessive Re content could lead to deterioration in oxidation resistance, mainly due to the accelerated formation of volatile Re oxides.

: Sulfate presence is of great importance for anaerobic digestion as its addition can control the anaerobic microbial community. In this study, the effect of sulfuric acid addition on the perfor-mance of an UASB reactor fed with hydrolyzed starch was investigated. TOC, Fe and SO4-2 re-moval as well as the methane production were monitored under various COD/ SO4-2 ratios, HRTs and OLRs. When HRT was 16 hours and OLR equal to 2 g COD/LUASB-d the methane production was 0.24 L CH4/LUASB-day. After the sulfuric acid addition, TOC removal reached 95%. At HRT, OLR, and COD/ SO4-2 ratio equal to 16 hours, 2 g COD/ LUASB-d and 3.72 respectively, the methane production was 0.267 L CH4/LUASB-d. When the OLR was increased to 5.94 g COD/LUASB-d and COD/SO4-2 ratio was equal to 12.5, the methane production was 3 times higher (0.84 L CH4/LUASB-d) with a methane content in the produced biogas greater than 70%. 16s rRNA gene analysis demonstrated that after the sulfate addition, SRB were enriched and methane was mainly produced by Methanosaeta sp. This study indicates that appropriate sulfate concentrations in the feed in combination with the presence of iron in the UASB reactor lead to enhanced me-thane yields.

In the present work, a comparative evaluation of an MBBR unit performance was carried out for the following cases: when adding 3D-printed biocarriers fabricated with 13X and bentonite, when using K1 commercial biocarriers and when not adding biocarriers at all. For the evaluation of the MBBR efficiency, various physicochemical parameters were measured, while static light scattering and optical microscopy observations were additionally used. Finally, biofilm extracted from the biocarriers was evaluated. The findings suggest that there is an optimal biodegradation of the organic load in all MBBR units. The nitrification and denitrification process were improved at the 3D MBBR as compared to the control MBBR and MBBR K1. The dry mass of the biofilm in the 3D-printed biocarriers was two orders of magnitude larger than the one in the K1 biocarriers. What is more, in the K1 biocarriers the mass of the biofilm varied in relation to time, due to the fact that it could not be kept inside the holes, something that was not observed to happen with the 3D-printed biocarriers. Finally, it was observed, mostly in the 3D MBBR and less in the K1 MBBR, that the growth of nitrifying bacteria and heterotrophs inside the units increased the biomass production in the form of SMP, which in turn favored the adhesion of biomass on the surface of biocarriers.

Glutathione (GSH) and melatonin (MLT) are two antioxidants that have been described as having a protective role against oxidative stress in several animal species, improving sperm quality and survival after cryopreservation. Since there is no knowledge on the simultaneous use of these two substances concerning its effects on ram semen cryopreservation, this study aimed to evaluate the effects of MLT, GSH, or their association, on in vitro parameters of ram semen after thawing. During eight weekly sessions, the semen from three Merino rams was pooled, divided into four aliquots, and diluted with an egg yolk-based semen extender without (control) and with antioxidants (MLT 1mM, GSH 5mM, and MLT 1mM + GSH 5mM). Diluted semen was evaluated before and after freezing process. Supplementation of fresh semen with GSH at 5 mM had a deleterious effect on total motility progressive (TPM), curvilinear velocity (VCL), straight-line velocity (VSL), average-path velocity (VAP), linearity (LIN), straightness (STR) and increased slow spermatozoon (%). MLT at 1 mM also has a negative effect on TPM, VSL, and STR in fresh semen. In thawed semen, 1 mM of melatonin increased the TPM regarding the group control. Also, the combination of both antioxidants attenuates the negative effect of GSH 5mM on TPM, VSL and BCF. These results indicate that 5mM GSH impairs or does not improve sperm kinetic parameters in fresh semen and suggest that melatonin when combined with GSH plays a protective role on these effects.

Zn–Ni plating is indispensable in various industries because of its high corrosion resistance. However, Ni has been reported to trigger allergies; thus, an alternative Ni-free plating is desired. Zn–Fe plating is considered to be a promising candidate, albeit its corrosion resistance still needs to be improved. The corrosion resistance of Zn–Fe plating is expected to increase by the addition of Mo as the third alloying element as it is more noble than Zn and Fe. In this study, Zn–Fe–Mo plating with a corrosion resistance nearly equivalent to that of the Zn–Ni plating was fabricated. Zn–Fe–Mo plating was electrically deposited from continuously agitated plating baths prepared by mixing ZnSO₄, FeSO₄, Na₂MoO₄, Na₃C₆H₅O₇, and Na₂SO₄ using Fe or Ni plates as the substrate. The surface morphology, composition, crystal phase, and electronic state of Mo of the platings were investigated by SEM-EDS, XRD, and XPS. The anti-corrosion performance was evaluated by Tafel extrapolation method. Formation of plating comprising a Mo containing alloy phase was found to be crucial for improving corrosion resistance. The Zn–Fe–Mo plating demonstrates promise for replacing anti-corrosion Zn–Ni platings.

In this work we looked for a stable and accurate procedure to perform feature selection in datasets with a much higher number of predictors than individuals, as in Genome-Wide Association Studies. Due to the instability in feature selection when many potential predictors are measured, a variable selection procedure is proposed that combines several replications of shrinkage regression models. A weighted formulation is used to define the final predictors. The procedure is applied to investigate Single Nucleotide Polymorphisms (SNPs) predictors associated to Alzheimer’s disease in the Alzheimer’s disease Neuroimaging Initiative (ADNI) dataset. Two data scenarios are investigated: one considering only the set of SNPs and another with the covariates age, sex, educational level and APOE4 genotype. The SNP rs2075650 and the APOE4 genotype are given as risk factors for AD, which is in line with the literature, and other four new SNPs are pointed, opening new hypotheses for in vivo analyses. These experiments demonstrate the potential of the new method for stable feature selection.

In this paper we describe a method which combines sentiment analysis with machine learning techniques and/or multivariate statistical analysis. By applying this methodology it is possible to classify a collection of texts into two or more groups or clusters. On the basis of a number of previously defined clusters, the novelty of the outlined approach is the use of the sentiment analysis results as input to the machine learning model or multivariate statistical analysis. Once the classifier has been obtained, we can assign a given text into one of the pre-established clusters. The groups or clusters can represent different time periods, classes of texts transcribed from different conversations, etc. The method is illustrated through an example taken from one of the two studies in which we have applied this methodology. In one of the studies, the method was used to classify press news of a volcanic eruption, while in the other study it was used to classify the conversations recorded between a chatbot with different kinds of speakers (humans or chatbots). This last study was the seminal work in which we introduced this methodology.

The thesis proposes a argument that a mass point moving in a horizontal circle on the Earth's surface can generate a radial centrifugal force of the Earth's center of mass, thus realizing an unconventional anti-gravity path. And through the theoretical analysis of the difference in the distribution of gravitational acceleration at different latitudes caused by the rotation of the earth, and the centrifugal force of a mass point moving in a horizontal circle on the earth's surface is analyzed, the validity of the argument is demonstrated. At the same time, the paper puts forward two possible basic principles, and makes theoretical analysis and demonstration. Conceive of the concrete experimental verification of principle two is proposed. Four technical schemes for antigravity ascent are proposed and basic analysis is made. On the premise of not fully considering the practical technical ability, it is theoretically proved that three of them have realistic operability and development potential. In theory, this paper opens up a different way of anti-gravity for human beings, which will bring new ideas and prospects for human beings to get rid of the bondage of gravity.

A construction for the systems of natural and real numbers is presented in Zermelo-Fraenkel Set Thoery, that allows for simple proofs of the properties of these systems, and practical and mathematical applications. A practical application is discussed, in the form of a Simple and Linear Fast Adder (Patent Pending). Applications to finite group theory and analysis are also presented. A method is illustrated for finding the automorphisms of any finite group $G$, which consists of defining a canonical block form for finite groups. Examples are given, to illustrate the procedure for finding all groups of $n$ elements along with their automorphisms. The canonical block form of the symmetry group $\Delta_4$ is provided along with its automorphisms. The construction of natural numbers is naturally generalized to provide a simple and sound construction of the continuum with order and addition properties, and where a real number is an infinite set of natural numbers. A basic outline of analysis is proposed with a fast derivative algorithm. Under this representation, a countable sequence of real numbers is represented by a single real number. Furthermore, an infinite $\infty\times\infty$ real-valued matrix is represented with a single real number. A real function is represented by a set of real numbers, and a countable sequence of real functions is also represented by a set of real numbers. In general, mathematical objects can be represented using the smallest possible data type and these representations are calculable. In the last section, mathematical objects of all types are well assigned to tree structures in a proposed type hierarchy.

The addition of flaxseed and amaranth on the physicochemical, functional and microstructural changes of instant-extruded cereals was evaluated. Six different mixtures were made with additions of amaranth (30%–50%) and flaxseed (10% and 15%) using maize grits and minor additives as supplementary ingredients and then extruded in a twin-screw extruder. The extrudates evaluated, had insoluble and soluble fiber contents increased with the proportion of amaranth and flaxseed. The mixture 4 (higher flaxseed content) presented highest soluble fiber percentage (1.9%). Extruded cereals had the lowest viscosity (<99.5 cp) and highest hardness values (5.2 N) whereas the dietary fiber content was highest. Fiber content increase, resulted in a higher water solubility index (WSI) (0.5) and decrease the water absorption index (WAI) (2.5). Amaranth and flaxseed incorporation increased crystallinity, resulting in a larger, and more compact laminar structure. Amaranth and flaxseed addition resulted in extruded cereals with acceptable physicochemical and functional properties.

Natural montane peatlands generally are not a significant source of nitrous oxide (N₂O) due to environment limitation including phosphorus (P) scarcity and temperature lowness. Phosphorus enrichment and warming caused by global change are altering this limitation, likely to increase the source function of N₂O. However, the combined effects of P addition and warming on N₂O fluxes and biotic/abiotic factor in peatlands are still uncertain. To address this, we investigated the long-term (12 yrs) effects of P addition (5 and 10 kg ha^-1 yr^-1) and its interaction with warming on N₂O fluxes in a peatland. The results showed that although long-term P addition did not significantly affect the source/sink function of N₂O in the peatland, it stimulated enzyme activities, promoted peat decomposition. However, warming amplified the effect of P addition to increase N₂O emissions by stimulating enzyme activities and changing soil stoichiometry, even turned the peatland into a significant source of N₂O with an emission of approximate 100 g m^-2 during the growing season. Our study suggests that P enrichment under the current background of global warming will enhance the possibility of strong N₂O emissions in montane peatlands, which may increase the risk to further aggravate global warming.

The variability observed in the annual seed production of perennial plants can be seen as an indication of changes in the allocation of resources between growth and reproduction, which can be attributed to fluctuations in the environment. However, a significant knowledge gap exists concerning the impacts of nitrogen addition on the interannual seed production patterns of perennial plant. We hypothesized that the addition of nitrogen would impact the annual variations in the seed production of perennial plants, ultimately affecting their overall reproductive efficiency. A multiyear field experiment was conducted to investigate the effects of varying nitrogen supply levels (e.g., 0, 4, 8 kg N ha−1 yr−1 of N0, N4, and N8) on the vegetative and floral traits, pollinator visitation rates, and seed traits over a period of four consecutive years. The results showed that the N0 treatment exhibited the highest levels of seed production and reproductive efficiency within the initial two years. In contrast, the N4 treatment displayed its highest level of performance in these metrics in the second and third years, whereas the N8 treatment showcased its most favorable outcomes in the third and fourth years. The similar patterns were found in the number of flowers per capitulum and the number of capitula per plant. There exists a positive correlation between aboveground biomass and several factors, encompassing the number of flowers per capitulum, the number of capitula per plant, the volume of nectar per capitulum, and the seed production per plant. This implies that the addition of N affected the maintenance of plant aboveground biomass, flower traits stability and, subsequently, the frequency of seed production, and the reproductive efficiency. Our results suggest that augmenting the nitrogen content in the soil may have the capacity to modify the inherent variability in seed production that is observed across various years. These findings have the potential to enhance our comprehension of the impact of nitrogen addition on the reproductive performance of perennial herbaceous plants, and the underlying mechanisms of biodiversity in the context of global environmental changes.

The method of micro-arc oxidation has been utilized to synthesize a protective biocompatible coating for a bioresorbable orthopedic Mg implant. This paper presents the results of a comprehensive research of micro-arc coatings based on diatomite – a biogenic material consisting of shells of diatom microalgae. The main focus of this study was the functionalization of diatomite-based micro-arc coatings by incorporating the particles of titania (TiO2) into them. Various properties of the resulting coatings were examined and evaluated. The XRD analysis has revealed the formation of a new magnesium orthosilicate phase – forsterite (Mg2SiO4). It has been established that the corrosion current density of the coatings has decreased by 2-4 orders of magnitude after the inclusion of TiO2 particles, depending on the coating process voltage. The adhesion strength of the coatings has increased following the particle incorporation. The processes of dissolution of both coated and uncoated samples in a sodium chloride solution were studied. The in vitro cell viability was assessed, which showed that the coatings significantly reduce the cytotoxicity of Mg samples.

Computational investigations on the BPE-ligated Cu-catalysed enantioselective addition of enynes to ketones were performed with DFT method. Two BPE-CuMes catalysts, BPE-CuMes and (S,S)-Ph-BPE–CuMes, were employed to probe the reaction mechanism with the emphasis on stereoselectivity. The calculations on the BPE-CuMes system indicate that the actvie metallized enyne intermediate acts as the catalyst for the catalytic cycle. The catalytic cycle involves two steps: 1) the ketone addition to the alkene moiety of the metallized enyne; 2) the metallization of enyne followed by the release of product with the recovery of the active metallized enyne intermediate. The first step accounts for the distribution of the products, and therefore is the stereo-controlling step in chiral systems. In the chiral (S,S)-Ph-BPE–CuMes system, the steric hindrance is vital for the distribution of products and responsible for the stereoselectivity of this reaction. The steric hindrance between the phenyl ring of the two substrates and groups at the chiral centers in the ligand skeleton is identified as the original of the stereoselectivity for the titled reaction.

Membrane distillation techniques appear as one of the most promise alternative to guarantee the availability of potable water in time of scarce of this essential resource. For membrane preparation, polyvinylidene fluoride (PVDF) is preferred due to the easier synthesis procedures with respect to other fluorine based polymers. In this work, copper oxide nanoparticles (CuONPs) at different weight percent (wt.%), embedded in PVDF membranes supported on non-woven polyester fabric (NWPET) were prepared by the phase-inversion method, and characterized by spectroscopy (ATR-FTIR, Raman) and electron microscopy techniques (SEM). The PVDF deposited onto the NWPET was highly composed by its polar -phase (F()= 53 %) which was determined from the ATR-FTIR spectrum. The F() value was kept constant, in the whole range of CuONPs studied (2-10 wt.%) as was determined from the ATR-FTIR spectrum. The absence of signals corresponding to CuONPs in the ATR-FTIR spectra and the appearance of peaks at 297, 360 and 630 cm-1 in the Raman spectra of the membranes suggested that the CuONPs are preferably located in the inner of the membrane but not on its surface. The membrane morphologies were characterized by SEM. From the obtained SEM micrographs, a decrease and increase in the amount of micropores and nanopores, respectively, near to the surface and intercalated in the finger-like layer were observed. As result of the CuONPs addition, the nanopores in the sponge-like layer decrease in size. The values of water contact angle (WCA) measurements showed a trend to decrease from 94° to 80° upon the addition of CuONPs (2-10 wt.%) indicating a diminish in the hydrophobicity degree of the membranes. Apparently, the increase in the amount of nanopores near to the surface decreased the membrane roughness becoming less hydrophobic.

Brushless Synchronous Machines (BSM) are replacing conventional synchronous machines with static excitation in generation facilities due to the absence of sparking and lower maintenance. However, this excitation system makes challenging measuring electric parameters in the rotor. This fact highly difficult the detection of ground faults, which are the most common type of electrical fault in electric machines. In this paper, a ground fault detection method for BSM is proposed. It is based on an inductive AC/DC rotating current sensor installed in the shaft. In case of a ground fault in the rotating parts of the BSM, a fault current will flow through the rotor’s sensor, inducing voltage in its stator. Analyzing the frequency components of the induced voltage the detection of a ground fault in the rotating elements is possible. The ground faults detection method proposed covers the whole rotor and discern between DC and AC sides. To corroborate the detection method, experimental tests have been performed using a prototype of this sensor connected to laboratory synchronous machines achieving satisfactory results.

The growth of plant and process of yield formation in crops are moderated by surrounding conditions as well as interaction of genetic background of plants and environment. In the last two decades significant changes in climate can be observed generating unfavorable and harmful impact on plant development. Drought stress can be considered as one of the most dangerous environmental factor influencing plant life cycle and decreasing production of biomass and finally the yield. Plants can react to water deficit in a wide degree what is dependent on the species, the genetic variability within the species, the phase of the plant ontogenesis, the intensity of stress, and other potential stress factors. In plants there can be observed hybrids between distinct taxa which exhibit certain traits adopted to tolerate stress conditions better than parental plants. Oat × maize addition (OMA) plants are good example of fertile hybrids with retained maize chromosomes as addition to complete oat genome. Hybrids generated via wide crossing can exhibit morphological, physiological and biochemical variations implemented by the occurrence of extra chromosomes of maize, as well as interaction of maize and oat chromatin. The molecular analysis indicated 12.5% OMA lines among all tested descendants of wide oat-maize crossing. On the fourteenth day of the drought, a significant effect of stress on the content of soluble sugars and phenolic compounds was observed, soil drought significantly reduced plant biomass above ground and several yield components. Less water lost revealed by results of the excised leaf water loss test was correlated with high yield of OMA lines. Phenolic compounds content might be used as biochemical indicator of plant drought tolerance since there were significant correlation with high kernel yields of plants subjected to drought stress.

Intensive development of many industries, including textile, paper or plastic, which consume large amounts of water and generate huge amounts of wastewaters containing toxic dyes, contribute to pollution of the aquatic environment. Among many known methods of wastewater treatment, adsorption techniques are considered as the most effective. In the present study the weakly basic anion exchangers such as Amberlyst A21, Amberlyst A23 and Amberlyst A24 of the polystyrene, phenol-formaldehyde and polyacrylic matrices were used for C.I. Direct Yellow 50 removal from aqueous solutions. The equilibrium adsorption data were well fitted to the Langmuir adsorption isotherm. Kinetic studies were described by the pseudo-second order model. The pseudo-second order rate constants were in the range of 0.0609-0.0128 g/mg·min for Amberlyst A24, 0.0038-0.0015 g/mg·min for Amberlyst A21 and 1.1945-0.0032 g/mg·min for Amberlyst A23, and decreased with the increasing initial concentration of dye from 100-500 mg/L, respectively. There were observed auxiliaries (Na2CO3, Na2SO4, anionic and non-ionic surfactants) impact on the dye uptake. The polyacrylic resin Amberlyst A24 can be promising sorbent for C.I. Direct Yellow 50 removal as it is able to uptake 666.5 mg/g of the dye compared to the phenol-formaldehyde Amberlyst A23 of the 284.3 mg/g capacity.

Successive-addition-of-digits-of-a-number(SADN) refers to the process of adding up the digits of an integer number until a single digit is obtained. Concept of SADN has been occasionally identified but seldom employed in extensive mathematical applications. This paper discusses SADN and its properties in terms of addition, subtraction and multiplication. Further, the paper applies the multiplication-property of SADN to understand the distribution of prime numbers. For this purpose the paper introduces three series of numbers -S1, S3 and S5 series- into which all odd numbers can be placed, depending on their SADN and the rationale of such classification. Extending the analysis the paper explains how composite numbers of the S1 and S5 series can be derived. Based on this discussion it concludes that even as the concept of SADN is rather simple in its formulation and appears as an obvious truism but a profound analysis of the properties of SADN in terms of fundamental mathematical functions reveals that SADN holds a noteworthy position in number theory and may have significant implications for unfolding complex mathematical questions like understanding the distribution of prime numbers and Goldbach-problem.

Cobalt oxide nanoparticles are promising candidates for various kinds of practical application. The interest of researchers and scientists in these nanoparticles is due to their unique physical and chemical properties such as density, melting point, magnetic characteristics and band gap. The need to develop high performance and low-cost technologies for obtaining Co3O4 nanoparticles is a major reason in research in this area. The widespread commercial use of Co3O4 nanoparticles will open doors for numerous novel cost effective technologies, which are mostly dependent on the type of synthesis method and raw materials. A possible solution to this problem is to use Cobalt nitrates as a cost-effective precursor using the solution combustion method. Solution combustion synthesis method is one of the best candidate methods that have the potential for high performance and is also cost-effective. This review examines recent progress in the synthesis of Co3O4 nanoparticles by solution combustion method and underscores their significance across various fields, highlighting the need for further research and exploration of their multifaceted applications. In addition, the most recent advancements in the applications of Co3O4 nanoparticles in sensitive sensing, catalysis, supercapacitors/batteries and water treatment/pollutants removal are reviewed and described, focusing on current trends, challenges, and future outlooks.

Titanium boride (TiB2) is a material classified as ultra-high temperature ceramics. The TiB2 structure is dominated by covalent bonds, which gives materials based on TiB2 very good mechanical and thermal properties, but also makes them difficult to sinter. Obtaining dense TiB2 polycrystals requires chemical or physical sintering activation. Carbon and molybdenum disilicide (MoSi2) were chosen as sintering activation additives. Three series of samples were made, the first with carbon additives: 0 to 4 wt.%; the second with 2.5, 5 and 10 wt.%. MoSi2 and the third with both additions of 2 wt.% carbon and 2.5, 5 and 10 wt.% MoSi2. MoSi2. On the basis of dilatometric sintering analysis, all additives were found to have a favourable effect on sinterability of TiB2, and it was determined that sintering of TiB2 with carbon addition can be carried at 2100°C and with MoSi2 and both additives at 1800°C. The polycrystals were sintered using the hot pressing technique. On the basis of the studies conducted in this work, it was found that addition of 1 wt.% of carbon allows to obtain single-phase TiB2 polycrystals of high density (>90%). The minimum MoSi2 addition required to obtain dense sinters with a cermet-like microstructure was 5 wt.%. High density was also achieved by materials containing both additives. Samples with higher MoSi2 content, i.e. 5 and 10% showed densities close to 100%. Mechanical properties such; as Young's modulus, hardness and fracture toughness (KIc) of the polycrystals and composites were similar for samples with densities exceeding 95%. The Vickers hardness was 23 to 27 GPa, the fracture toughness (KIC) was 4 to 6 MPa·m0.5 and the Young's modulus was 480 to 540 GPa. The resulting TiB2-based materials showed potential in high-temperature applications.

Virgin Argan Oil (VAO) is extracted from the fruits of the Moroccan endemic species argan [Argania spinosa (L.) Skeels]. It is known for its richness in polyunsaturated fatty acids and its unique composition in tocopherols conferring a panoply of pharmacological properties, documented in several studies. The aim of this study was to investigate the potential protective effect of VAO against oxidative and nitrosative stress induced in cells of the model species Tetrahymena pyriformis. As a comparison, well-known Virgin Olive Oil (VOO) from Olea europaea L. was used instead. Both oils were subjected to a preliminary analysis of phytochemicals and properties of interest. Oxidative stress in T. pyriformis cells was induced by hydrogen peroxide (H2O2) at 350µM, whereas sodium nitroprusside (SNP) nitrosative stress was induced using a 1mM concentration. Neither of these concentrations caused relevant changes in cell viability. The level of reactive oxygen species (ROS) was evaluated in the cell cultures by using H2-DCFDA dye. The activity and cell localization of the antioxidant enzymes catalase (CAT), superoxide dismutase (SOD) and glutathione peroxidase (GPX) was evaluated as well as the levels of glutathione (GSH) and the malondialdehyde (MDA) generated after lipid peroxidation. Finally, the presence and localization of intracellular lipid droplets was assessed by using Nile red. The treatment of cultures with H2O2 produced significant increases in the activity of CAT, SOD and GPX and in the level of GSH, as also did the SNP treatment. MDA level was increased by both the treatments. VAO and VOO treatment were found to protect T. pyriformis from oxidative stress and increased cells defense in nitrosative stress. In another hand VAO and VOO decreased significantly MDA level increased by H2O2 treatment and failed after SNP treatment. The quantification of fluorescence signal obtained from immunolocalization of antioxidant enzymes confirmed the results obtained after the evaluation of their activities. Interestingly the level of ROS and the number of lipid droplets increased by H2O2 treatment was significantly decreased by VAO and VOO co-treatments. VAO and VOO represent strong antioxidants, playing an important role in protecting cells against oxidative stress.

The extrusion of food for human and animal consumption is a unit operation that includes mixing, shearing and force to the materials related to the rheological properties of the materials in the extruder. The present work aims to study the rheological behavior of an extruded fish diet incorporating hydrolyzed protein flour processed by extrusion. The measurement was carried out online with a slit die rheometer, defining the rheological models and parameters that fit the process. During the extrusion process, the raw materials used were hydrolyzed protein meal, fish meal and cassava starch. For the results, the evaluated treatments were adjusted to the Power Law, where an increase in the shear rate decreases the viscosity of the material, corresponding to a pseudoplastic behavior. The incorporation of hydrolyzed protein flour presented a significant effect on the value of n and Klp, increasing the viscosity with the increase in the percentage of inclusion of HPH. The models obtained for the prediction of the viscosity are adjusted to the changes in shear rate, temperature and humidity of the system.

Hybrid forecasting methods have emerged as a solution surpassing the limitations of both statistical and deep learning approaches. While the first emphasize the significance of variables, they often produce worse forecasting results when compared to newer techniques. In contrast, deep learning models remain enigmatic "black boxes" in terms of interpretability, although achieving better results in forecasting. This article introduces the Comprehensive Cross-Correlation and Lagged Linear Regression Deep Learning (CCLR-DL) framework, designed to harness the best of both approaches, enhancing forecasting accuracy while retaining model interpretability through a feature selection process. CCLR-DL blens cross-correlation analysis, lagged multiple linear regression and granger's causality procedures with deep learning architectures based on LSTM. In a practical demonstration, CCLR-DL was applied to a real database of clinical visits associated to diagnoses in Catalonia, Spain (tracking a population of 6.3 million patients during 10 years). Predicting visits enables the healthcare managers to be ready for future demand shifts. Results demonstrate a consistent and substantial improvement over standalone statistical and deep learning methods when predicting healthcare demand. This hybrid approach not only showcases its efficacy but also offers a promising solution to the challenge of balancing predictive accuracy with model explicability. In this context, this work aims to design and validate a method for feature selection and forecasting of multivariate high dimensional time series datasets not only to improve prediction accuracy but also to model transparency by identifying a subset of variables that improve predictions and G-cause the target variable.

In view of the problem that the output thrust of solenoid actuator is affected by various factors and is difficult to calculate in actual working conditions, this paper proposes a semi-analytical model constructed by magnetic field subdomain method with internal and external boundary conditions in cylindrical coordinate system for calculation, and the general solution equations of magnetic vector potential for each subdomain are derived and solved by MATLAB. Taking a push-pull electromagnet as an example, the finite element simulation and experimental comparative analysis are carried out. The correctness and applicable conditions of the subdomain method are illustrated by comparing the gradient plot of magnetic vector potential, inductance curve and electromagnetic force. By calculating the output thrust after considering the core gravity, spring force and electromagnetic force, it is shown that this method has the advantage of computational flexibility compared with the finite element method, and it is easier to write special algorithms according to various working conditions to calculate the important parameters in engineering applications.

The present study analyzed the effect of temperature, pH, retention time, pretreatment and mixing ratio on the anerobic digestion process. The parameters during the anaerobic co digestion of cow manure and food waste were then optimized using the Taguchi experimental design method. ANOVA is carried out to find the significant parameters which influence the biogas production. Experimental tests were carried out at laboratory scale reactors kept at different temperatures (28 °C, 35 °C, and 50 °C). The specific methanogenic Performance (SMP) during anerobic digestion at higher temperatures was characterized with the analysis of acetate, propionate, butyrate, hydrogen, glucose, and formate. The improvement of biogas production with different pre-treatment i.e., ultrasonic, autoclave, and microwave techniques also analysed. The results showed that reactor that maintained at 35 °C showed the highest biogas production. While the reactor that maintained at lower temperature (28 °C) produced the lower volume of biogas. As the retention time increases, the amount of biogas produced increases. Methanogenic activities of microorganisms reduced at higher temperature conditions (65 °C). Biogas production increased by 28.1%, 20.23%, and 13.27 % when the of substrates treated with ultrasonic, autoclave, and microwave, respectively, compared to the untreated substrate. The optimized condition for the highest biogas production during anaerobic co digestion of food waste and cow manure is temperature of 35 °C, pH of 7 and mixing ratio (CM: FW=1.5:0.5). ANOVA showed that temperature is the most important input parameter affecting biogas production, followed by mixing ratio.