Three-dimensional (3D) printing technology, also known as additive manufacturing (AM), has emerged as an attractive state-of-the-art tool for precisely fabricating functional materials with complex geometries, championing several advancements in tissue engineering, regenerative medicine, and therapeutics. However, this technology has an untapped potential for biotechnological applications, such as sensor and biosensor development. By exploring these avenues, the scope of 3D printing technology can be expanded and pave the way for groundbreaking innovations in the biotechnology field. Indeed, new printing materials and printers would offer new possibilities for seamlessly incorporating biological functionalities within the growing 3D scaffolds. Herein, we review the extrusion-based 3D printing modalities emphasizing biosensor applications. We highlighted the application of natural, synthetic, and composite biomaterials as 3D-printed soft hydrogels. Emphasis was placed on the approach by which the sensing molecules were introduced during the fabrication process. Finally, the future perspective was provided.

The paper presents a method to assess the effect of electrolyte additives on the energy capacity of Pb-acid batteries. The method applies to any chemically unreactive additive, including suspensions and gels. The approach is thermodynamically based and it leads to the definition of a region of admissible concentrations –the battery’s admissible range– where the battery can undergo an indefinite number of charge/discharge cycles without suffering permanent damage. An experimental procedure to determine this range is presented. The obtained results provide a way to assess the potential of electrolyte additives to improve the energy capacity of Pb-acid batteries. The same results also provide a means to determine the additive concentration that produces the maximum energy capacity increase of the battery. The paper closes with an example of application of the proposed approach to a practical case.

This study explores the potential to reach a circular economy for post-consumer recycled polyethylene terephthalate (rPET) packaging and bottles by using it as a distributed recycling for additive manufacturing (DRAM) feedstock. Specifically, rPET is processed using only an open source toolchain with fused particle fabrication (FPF) or fused granular fabrication (FGF) processing. In this study, first the impact of granulation, sifting and heating (and their combination) is quantified on the shape and size distribution of the rPET flakes. Then feeding studies were performed to see if they could be printed through an external feeder or needed to be direct printed with a hopper using two Gigabot X machines, one with extended part cooling and one without. Print settings were optimized based on thermal characterization and for the latter which was shown to print rPET directly from shredded water bottles mechanical testing is performed. The results showed that geometry was important for extended feeding tubes and direct printed using a hopper. Further there is a wide disparity in the physical properties of rPET from water bottles depending on source and the history of the material. Future work is needed to enable water bottles to be used as a widespread DRAM feedstock.

Plasma electrolytic polishing (PeP) is mainly used to improve the surface quality and thus the performance of electrically conductive parts. It is usually used as an anodic process, i.e. the workpiece is negatively charged. However, the process is susceptible to high current peaks during the formation of the vapour skin especially when polishing workpieces with a large surface area. In this study, the critical influence of workpiece submerging velocity on the current peaks and the average power during the initialisation of the PeP process is investigated for a workpiece size of microreactor mould insert. Through systematic experimentation and analysis, this work provides insights into the control of the initialisation process by modulating the workpiece submerging velocity. The results clarify the relationship between submerging velocity, peak current and average power and provide a novel approach to improve process efficiency in PeP. The highest peak current and average power occur when the electrolyte splashes over the top of the workpiece and not, as expected, when the workpiece touches the electrolyte. By submerging the workpiece while the voltage is applied to the workpiece and counter electrode, the reduction in both parameters is over 80 %.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

This article explores the emerging concept of atrial myopathy (AM) and its potential role as a risk factor for stroke and dementia, both independently and in association with atrial fibrillation (AF). AM refers to structural and functional abnormalities of the atria, potentially causing blood clots formation and their subsequent embolization even in patients without AF. Echocardiography, particularly Left Atrial (LA) strain analysis, is a promising non-invasive tool for AM evaluation and might offer additional risk stratification beyond the established CHADS2-VASc score, potentially impacting anticoagulation decisions. By understanding AM and utilizing advanced imaging techniques like LA strain, clinicians can achieve a more comprehensive understanding of thromboembolic risk in specific patient groups. Integrating LA strain analysis into routine clinical practice holds promise for improved patient management and targeted therapies, allowing for better risk stratification in AF patients. However, standardized definitions and diagnostic criteria for AM are essential for consistent evaluation and research. Further studies are needed to explore the efficacy and safety of anticoagulation in AM patients without AF.

Nitrate and nitrite are the most extensively used food additives in the food industry for their multifunctional properties, and they have been in the spotlight for decades for its controversial back effects. The conversion of nitrate and nitrite to various nitroso compounds, specifically N-nitrosamine raises the question of the integrity of these additives. Nitrosamine is a well-known carcinogen and mutagen. A large number of studies demonstrate the carcinogenic effects of these salts. Are these findings credible? Nonetheless, the regulatory agencies approve its usage; is it biased? Are we feeding on the carcinogens in processed foods? The current work provides an insight into the basic and toxicological findings of the food additives -nitrate and nitrite.

The paper delves into an extensive exploration of the integration of the circular economy paradigm within the realm of additive manufacturing (AM). The objective is to comprehensively investigate existing methodologies for structuring the symbiotic relationship between circular economy and additive manufacturing, while meticulously analyzing the current research gap concerning the implementation of circular economy principles in additive manufacturing practices. A thorough review focusing on the sustainability of additive manufacturing within the circular economy framework was conducted. This review aims to recognize and delineate pertinent aspects related to post-use material valuation in AM, recyclability of materials, and the environmental footprint associated with these processes. Emphasis was placed on the significance of examining circular economy facets concerning additive manufacturing processes to establish a holistic understanding. The overarching goal of this review is to augment knowledge regarding the potential advantages and benefits derived from the seamless integration of circular economy principles within AM. By elucidating the activities essential to attain compliance with the Sustainable Development Goals, this study endeavors to illuminate the pathway toward promoting sustainable development through the harmonious marriage of additive manufacturing and the circular economy.

Additive manufacturing (AM) provides opportunities to design objects differently than traditional manufacturing methods allow, but only if designers understand the possibilities AM presents. In this study, we examined whether an AM workshop combined with an idea generation session could inspire engineering professionals to use AM solutions to solve current technical problems they face. All subjects were employees at an organization that will be referred to as Company X, a multinational commercial organization based in North America. During the study, we collected ideas for 24 projects generated before and after a training workshop focused on design for AM. In the workshop, we provided three hours of instruction about design for two metal-based AM processes. The participants’ ideas were assessed using four specific metrics: (1) cost, (2) time,(3) completeness of solution, and (4) quality, which was a function of feasibility, usefulness, and novelty. Using these data, we explored whether the workshop was effective in inspiring the participants to use AM methods and techniques from AM research in their concept generation and whether participants’ AM solutions showed improvement in cost, implementation time, and quality over non-AM designs generated before the workshop.

This paper provides an overview of the new CPAM Project on Additive Manufacturing (AM) in design and simulation, focusing on topology & lattice structure optimization for a light-weighting advantage. This industry/academia collaboration project aims to utilize existing hardware and software tools, and investigate the practical limits of the technologies, providing eventual guidelines for general use. This will provide a solid foundation for the practical use of metal AM optimized solid and latticed structures especially for Ti6Al4V parts. Two case studies are demonstrated here, one a purely topology optimized design, and one also incorporating lattice optimized design, both from Ti6Al4V and load-bearing components, to be utilized in the Nelson Mandela University (NMU) Eco-Car Project in competition, late in 2018. This paper presents the Design for Additive Manufacturing (DfAM) process, the challenges met iro applying a DfAM design mindset, and a unique final voxel-based smoothing step finishing off the design process. Detailed structural integrity assessment of these parts are included - the question remains: can Additive Manufacturing help win the race?

We demonstrate a new quantitative method to the sieve of Eratosthenes, which is an alternative to the sieve of Legendre. In this method, every element of a given set is sifted out once only, and therefore, this method is free of the Mobius function and of the parity barrier. Using this method, we prove that every sufficiently large even number is the sum of two primes, and that every even number is the difference of two primes in infinitely many ways.

Additive manufacturing (AM) has revolutionized the field of biopolymers by providing a range of opportunities to create complex and intricate structures. Here we provide an overview of developments in biopolymer AM, first in the context of how natural systems have impacted the synthetic processes of AM, and secondly in the context of how synthetically derived structures can be used for biomedical applications. In particular, we explore the range of biopolymers developed for AM, AM techniques for biopolymers, and potential biocompatible medical applications with a focus on four categories of tissue in the human body: skin, bone, heart, and nerve. Despite the current challenges of the technology, exciting results in tissue regeneration, synthetic replacements for natural grafts, and complex dynamic organoids have already come to pass - with many more possible in the future.

Additive Friction Extrusion Deposition (AFED) is a recently developed additive manufacturing technique that promises high deposition rates at low forces. Due to the novelty of the process, the underlying phenomena and their interactions are not fully understood, and in particular the processing strategy and tool design are still in their infancy. This work contributes to the state of the art of AFED through a comprehensive analysis of its working principles and an experimental program including a representative sample component. The working principle and process mechanics of AFED are broken down into their individual components. Forces, their origins and effects on the process are described, and measures of process efficiency and theoretical minimum energy consumption are derived. Three geometrical features of the extrusion die are identified as most relevant to the active material flow, process forces and deposition quality: the topography of the inner and outer circular surfaces and the geometry of its extrusion channels. Based on this, the experimental program investigates seven different tool designs in terms of efficiency, force reduction and throughput. The experiments using AA 6061-T6 as feedstock show that AFED is capable of both high material throughput (close to 550 mm³/s) and reduced substrate forces: For example, the forces for a run at 100 mm³/s remained continuously below 500 N, and for a run at 400 mm³/s below 3500 N. Material flow and microstructure of the AFED are assessed from the macrosections. Significant differences are found between the advancing and retracting sides for both process effects and material flow. Banded structures show strong similarities to other solid state processes. The fabrication of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical testing, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, in the microstructure show strong similarities to other solid-state processes. The manufacturing of the sample components demonstrates that AFED is already capable of producing industrial grade components. In mechanical tests, interlayer bonding defects result in a more brittle failure behavior in the direction of the structure, while in the horizontal direction of the structure mechanical properties corresponding to a T4 temper have been achieved.

The recent decade has witnessed the evolution of a novel paradigm of alloying which is based on utilising multiple elements to design compositionally complex alloys also known as high entropy alloys (HEAs). Conventional manufacturing of HEAs has a number of drawbacks, especially in terms of mechanical properties and design complexities. This has been addressed by additive manufacturing (AM), which has not only led to the fabrication of complex-shaped HEA components but has also enabled both ex-situ and in-situ tailoring of alloy microstructures. Considering the increasing interest in AM-based fabrication of HEAs in the last ten years, the present chapter is aimed at highlighting the present status and challenges in the avenue of AM of HEAs. This has been followed by a discussion on the recent trends in the avenue of AM-based fabrication of HEAs from the viewpoints of (i) microstructure evolution and mechanical properties, and (ii) alloy fabrication techniques. The chapter ends with a discussion on the future prospects in the aforementioned avenue.

Background: Advances in additive manufacturing and the development of antimicrobial biopolymers facilitate the production of critical medical devices with strong and safe biocidal properties. The purpose of this study was to assess the antimicrobial efficacy, safety, and longevity of a polylactic acid-based biopolymer supplemented with a copper-based composite additive. Methods: An antimicrobial polylactic acid-based biopolymer was tested against several inoculants including Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Material safety was evaluated according to international testing standards for in vitro cytotoxicity. Results: The main findings of the present investigation showed a strong and long-lasting biocidal effect of a polylactic acid-based biopolymer embedded with a copper-based composite additive against Staphylococcus Aureus, MRSA, E. coli, Listeria, HCoV-229E (a SARS-CoV-2 surrogate), and HIV-1. Furthermore, the cytotoxicity and safety assessment of the antimicrobial biopolymer was found to be “non-toxic” and safe for human skin contact. Conclusions: The present investigation showed that the antimicrobial biopolymer exhibits strong and long-lasting biocidal properties against an array of viral and bacterial inoculants.

Metal Additive Manufacturing (MAM) has emerged as a promising technology in the aerospace industry, enabling the production of complex components with enhanced design flexibility and reduced lead times. Concurrently, Industry 4.0 has gained significant attention for its potential to revolutionize aerospace manufacturing processes. The paper aims to cluster and review the literature on MAM in the aerospace industry, specifically focusing on its relevance to Industry 4.0 and its applicability throughout the various stages of the product life cycle for the chief purpose of matching supply with demand. Identified gaps and challenges are analyzed, highlighting the need for further research and outlining research agenda aimed at advancing the integration of MAM for Industry 4.0 in the aerospace sector. By addressing these research areas, the aerospace industry can unlock the value of MAM within an Industry 4.0 framework, leading to improved efficiency, productivity, and competitiveness.

Porous structured metallic implants are preferable as bone graft substitutes due to their faster tissue integration mediated by bone in-growth and vascularization. The porous scaffolds/ implants should also mimic the graded structure of natural bone to ensure a match of mechanical properties. This article presents a method to design graded porous structured acetabular implant and identifies the suitable parameters for manufacturing the model through additive manufacturing. The design method is based on slice-wise modification to ensure continuity of gradation. Modification of the slices was achieved through the binary image processing route. A geodesic dome type design was adopted for developing the acetabular cup model from the graded porous structure. The model had a solid shell with the target porosity and pore size gradually changing from 65% and 950 µm, respectively, in the inner side to 75% and 650 µm, respectively, towards the periphery. The required dimensions of the unit structures, and the combinations of pore structure and strut diameter to obtain the target porosity and pore size were determined analytically. Suitable process parameters were identified to manufacture the model by Direct Metal Laser Sintering (DMLS) using Ti6Al4V powder after carrying out a detailed experimental study to minimize the variation of surface roughness and warping over different build angles of the strut structures. A dual contour scanning was implemented to simplify the scan strategy. The minimum diameter of struts that could be manufactured using the selected scanning strategy and scanning parameters was found to be 375 µm. Finally, the model was built and from the micro-CT data, the porosities and pore sizes were found to be closely conforming to the designed values. The stiffness of the structures, as found from compression testing, was also found to be well matching with that of human trabecular bone. Further, the structure exhibited compliant bending-dominated behavior under compressive loading.

Additive manufacturing has already been established as a highly versatile manufacturing technique with demonstrated potential to completely transform conventional manufacturing in the future. The objective of this paper is to review the latest progress and challenges associated with the fabrication of multi-material parts using additive manufacturing technologies. Various manufacturing processes and materials used to produce functional components were investigated and summarized. The latest applications of multi-material additive manufacturing (MMAM) in automotive, aerospace, biomedical and dentistry field were demonstrated. Investigation on the current challenges were also carried out to predict the future direction of MMAM processes. It is concluded that the further research and development needed in the design of multi-material interfaces, manufacturing processes and material compatibility of MMAM parts are necessary.

(1) In recent ten years, with the fast development of digital and engineering manufacturing technology, additive manufacturing has already been more and more widely used in the field of dentistry, from the first personalized surgical guides to the latest personalized restoration crowns and root implants. (2) Especially, the bioprinting of teeth and tissue is of great potential to realize organ regeneration and finally improve the life quality. (3) In this review paper, we firstly presented the workflow of additive manufacturing technology. Then we summarized main applications and recent research progresses of additive manufacturing in dentistry. (4) Lastly, we sketched out some challenges and future directions of additive manufacturing technology in dentistry.

In this article, metallic additive manufacturing (AM) processes were classified and demonstrated. AM technology can be applied to a wide range of industrial areas because of its great feasibility in the design and manufacturing of various complex parts. The main factor that distinguishes various metallic AM processes from each other is the deposition method. Deposited metal can be imported in the form of melt or semi-solid. AM technology also covers a wide range of materials like aluminum, titanium, and many other alloys. Some of the common applications of metallic AM processes are the quick manufacturing of the parts which utilized in various industries like medical, automotive, aerospace, and jewelry industries. AM can help to fabricate parts that are impossible to be manufactured by other processes.

Additive Manufacturing and nanotechnology have been used as basic tools for the manufacture of nanostructured parts with magnetic properties to expand the variety of applications in additive processes by tank photopolymerization. Magnetic cobalt ferrite (CoFe2O4) and barium ferrite (BaFe12O19) nanoparticles with the size distribution of average value DTEM of 12 ± 2.95 nm and 37 ± 12.78 nm, respectively were generat-ed by hydroxide precipitation method. The dispersion of the nanoparticles on commercial resins (Anycubic Green and IRIX White resin) was obtained by mechanochemical reactions carried out in an agate mortar for 20 minutes, at room temperature and with limited exposure to light. The product of each reaction was placed in amber vials, also being kept in a box, to avoid contact with light. The photopolymerization process was carried out only at low concentrations (w/w % nanoparticles/resin) since, at high concentrations, there is no for-mation of pieces due to the high refractive index of ferrites. Raman shift spectroscopy of the final pieces showed that they contain the magnetic nanoparticles, with no apparent chemical changes. The EPR results of the pieces maintain the magnetic properties and apparently, they are not modified during the photopolymer-ization. Although significant differences were found in the dispersion process of the nanoparticles in each piece, we determined that the photopolymerization did not influence the structure and superparamagnetic behavior of ferrite nanoparticles during processing, and the magnetic properties were successfully transferred to the final 3D-printed magnetic obtained piece.

Additive manufacturing (AM) technologies show potential for the development of functionally integrated lightweight designs, biomimetic structures and material savings. Typically, as-built surfaces show powder particle agglomerations and re-entrant features, leading to rough surfaces, which are associated with poor fatigue performance. To benefit from the full range of advantages with special focus on aerospace applications, critical features for crack initiation when subjected to fatigue loading need to be identified and mitigated. A first step toward achieving this goal is the surface texture characterisation based on the quantification of surface features. In this paper, selected areal height, functional and feature parameters from ISO 25178-2:2022 are generated and process-specific features are examined for as-built AlSi7Mg0.6 from laser powder bed fusion (PBF-LB). A connection with the particle size distribution of the used powder is demonstrated. It is shown that surface feature analysis opens up opportunities to use physically meaningful surface characteristics in future quality assurance and part qualification processes.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

Additive manufacturing, commonly referred to as 3D printing, is an exciting and versatile manufacturing technology that is gaining traction and interest in both academic and industrial settings. Polymeric materials are essential components in a majority of the “inks” used across the various 3D printing technologies. As the environmental ramifications of sole or primary reliance on petrochemicals as a resource for industrial polymers continue to manifest themselves at a global scale, a transition to more sustainable bioderived alternatives could offer solutions. In particular, cellulose is promising due to its global abundance, biodegradability, excellent thermal and mechanical properties, and ability to be chemically modified to suit various applications. Thus far, cellulose has typically been incorporated in additive manufacturing applications as a substrate, filler, or reinforcement for other materials. However, due to its versatility and desirable properties, the exploration of all-cellulose 3D printing materials and associated methodologies is increasing. This review will discuss the progress and status of all-cellulose 3D printing approaches, associated challenges, and their potential as a key player in a more sustainable industrial future.

The 70/30 copper–nickel alloy is mainly used in critical parts with more demanding conditions in marine settings. There is a need for innovative methods that offer fast production and cost-effectiveness to supplement current copper–nickel alloy manufacturing processes. In this study, we employ wire-arc additive manufacturing (WAAM) to fabricate the 70/30 copper–nickel alloy. The as-built microstructure is characterized by columnar grains with prominent dendrites and chemical segregation in the inter-dendritic area. The aspect ratio of the columnar grain increases with increasing travel speed (TS) at the same wire feed speed (WFS). This is in contrast to an equiaxed grain structure with a more random orientation of conventional sample. The sample built with a WFS of 8 m/min, TS of 1000 mm/min, and a track distance of 3.85 mm exhibits superior corrosion properties in the 3.5 wt% NaCl solution compared to the conventional one, as evidenced by a higher film resistance and breakdown potential, along with a lower passive current density of the WAAM sample. The corrosion morphology reveals the critical roles played by the nickel element unevenly distributed between the dendrite core and inter-dendritic area.

Additive manufactured interlocking structures often face challenges in achieving suitable joinability due to thermal deformation. This issue becomes particularly interesting when fabricating structures that require high density but not fully connected layers, such as soft-magnetic materials. This study focuses on systematical investigation of the deformation as a function of finger thickness and building direction in model interlocking structure. In the perpendicular direction to the build plate, the distortions of joint part were significantly reduced due to lower thermal stress. In addition, the effect of laser power and scan speed on interlocking structure are systematically discussed. Additionally, through stress and thermal simulations of additive manufacturing process, it was confirmed that the compensated model can enhance the joinability of interlocking structures. These findings contribute to the development of optimal design for additive manufactured parts of soft magnetic materials such as stators in electric motor components, which needs insulations and density.

Metal additive manufacturing technologies have large potential for future use in load bearing aerospace applications, requiring a deeper understanding of mechanical performance and influencing factors. The objective of this study is to manufacture fatigue specimens by laser powder bed fusion with comparable bulk and different as-built surface quality (without post-processing). This goal was pursued by using identical bulk/hatch scan parameters while varying contour scan parameters. The bulk quality was evaluated by density measurements according to Archimedes’ principle and tensile testing. The surfaces were investigated using the optical fringe projection method and surface quality was assessed by the areal surface texture parameters Sa (arithmetic mean height) and Sk (core height, derived from material ratio curve). The resulting mean values of max (ultimate tensile strength) were between 375 and 405 MPa, which is a variation of roughly 8%, for seven different surface conditions. It could be confirmed that the influence of contour scan variation on bulk quality is insignificant for the assessed samples.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

Fatigue remains a challenge especially for high end metal AM parts and materials. From a design perspective, the fatigue limit of an AM solution can be improved upon by optimizing the manufacturing process for a certain material and part. In addition, improved accuracy of design methodologies aids in capturing the features critical for fatigue and quantifies their significance to desired part lifetime as well as providing a basis for their avoidance. In current work we present an overall concept merging thermomechanical process and powder bed solidification modeling to micromechanical analysis of fatigue of the resulting material microstructure. Material features critical to fatigue, particularly surface roughness, internal defects such as porosity and cracks and on the other hand inclusions, can be assessed directly on the basis of AM part microstructure with respect to the resulting fatigue limit. Case analyses consist of maraging steel and nickel alloys. The overall scheme provides a basis for optimization of metal AM solutions against fatigue and multiscale modeling founded basis for fatigue design.

Techniques for the controlled seeding and growth of cracks are urgently required for non-destructive testing technique evaluation, particularly for additive manufactured (AM) samples. This paper describes a method which uses a combination of tensile load and resonance excitation of notched AM samples, with in-situ monitoring of the resonance frequency serving to track crack dimensions. Mechanical low-cycle fatigue cracks, ranging in length from ~0.3 mm to ~5 mm, are successfully created in five AM samples using this technique. The samples are non-destructively characterized using optical microscopy and Nonlinear Resonance (NLR) testing. The exploitation of resonance enables the concentration of a significant number of stress cycles on the samples in much shorter timespans than conventional fatigue testing, enabling high throughput, while utilising compact components. Furthermore, the tracking of resonance frequency shift throughout the process enables non-invasive and non-contact real-time condition monitoring.

The world is facing a serious energy crisis and environmental pollution problems due to a sharp increase in the world population. Bioenergy is an eminent solution to these problems. Anaerobic digestion is a green energy technology used worldwide for the conversion of organic waste to biogas. It is reported that organic wastes are hard to digest and need some technical improvement in the anaerobic digestion process to improve biogas yield. Iron-based additives, due to their electron acceptance and donation capabilities, have been emphasized as being exceptional in improving anaerobic digestion process efficiency amongst all other enhancement options. This study reviews the major available types of iron-based additives, their characteristics, and their preparation methods. The preferred iron-based additive that has a significant effect on the enhancement of biogas yield is also discussed. The use of iron-based additives in the anaerobic digestion process with varying dosages and their impact on the biogas generation rate is also being studied. Substrates, operating parameters, and types of anaerobic digesters used in recent studies while researching the effects of iron-based additives are also part of this review. Lastly, this study also confirms that iron-based additives have a significant effect on the reduction rate of the volatile suspended solids, methane content, biogas yield, and volatile fatty acids.

One century ago, ferroelectricity and then piezoelectricity were discovered using Rochelle salt crystals. Today, modern societies are invited to switch towards a resilient and circular economy model. In this context, this work proposes a method to manufacture piezoelectric devices made from agro-resources such as tartric acid and polylactide significantly reducing the energy budget without requiring any sophisticated equipement. These piezoelectric devices are manufactured by liquid phase epitaxy grown Rochelle salt (RS) crystals into a 3D printed poly(Lactic acid) (PLA) matrix being the artificial squared meshes which mimic the natural wood anatomy. This composite material can easily be produced in any fablab with renewable materials and at low processsing temperatures, reducing then the total energy consumed. Manufactured biodegradable samples are fully recyclable and have good piezoelectric properties without any pooling step. The measured piezoelectric coefficients of manufactured samples are higher than many piezoelectric polymers such as PVDF-TrFE.

Hybrid machine tools combining additive and subtractive processes have arisen as a solution to the increasing manufacture requirements, boosting the potentials of both technologies, while compensating and minimizing their limitations. Nevertheless, the idea of hybrid machines is relatively new and there is a notable lack of knowledge in the field. Therefore, in the present paper, an insight into the advancements of hybrid machines is given, identifying their real capabilities, together with the latest developments from an industrial context. In addition, the current situation and future perspectives of hybrid machines from the point of view of process planning, monitoring and inspection are discussed. Finally, the challenges that must be overcome and the opportunities that the hybrid machines will provide in the forthcoming years are presented.

Polyphenols and fermentable fibers have shown favorable effects on gut microbiota composition and metabolic function. However, few studies have investigated whether combining multiple fermentable fibers or polyphenols may have additive beneficial effects on gut microbial states. Here, an in vitro fer-mentation model, seeded with human stool combined from 30 healthy volunteers, was supplemented with blends of polyphenols (PP), dietary fibers (FB) or their combination (PPFB) to determine influence on gut bacteria growth dynamics and select metabolite changes. PP and FB blends independently lead to significant increases in the absolute abundance of select beneficial taxa, namely Ruminococcus bromii, Bifidobacterium spp., Lactobacillus spp. and Dorea spp. Total short chain fatty acid concentrations, relative to non-supplemented control (F), increased significantly with PPFB and FB supplementation, but not PP. Indole and ammonia concentrations decreased with FB and PPFB supplementation, but not PP alone while increased antioxidant capacity was only evident with both PP and PPFB. These findings demonstrated that, while the independent blends displayed selective positive impacts on gut states, combination of both blends provided an additive effect. The work outlines the potential of mixed substrate blends to elicit a broader positive influence on gut microbial composition and function to build resiliency toward dysbiosis.

Automobile industry is recognized as one of the most influential sectors shaping the global economies, societies, and individual lifestyles. Therefore, fierce competitions among different companies are continuously undergoing, and innovations deserve special attention to improve the competitiveness. In the past several years, additive manufacturing (AM) is emerging as an innovative technology in the applications of automobile industry with significant advantages over traditional techniques. As a result, increasing attention has been attracted to combining AM technology with the development of automobile industry. Currently, many automobile players are optimizing their industrial layout by incorporating with innovative AM techniques, and meanwhile, many research progresses have been achieved to meet the market demand. This article aims at presenting a timely review to conclude the recent advances in the application of AM techniques in automobile industry, focusing on the available AM techniques, printable materials, and the industry applications. The future research opportunities and challenges are also outlooked. Hopefully, this work can be useful to the related researchers, as well as the game players in the industry of this field.

The paper presents the conceptualization and realization of a novel platform for additive manu-facturing, an industrial robot arm-based system for additive manufacturing applications. Tradi-tional 3D printers, especially those employing fused deposition modelling (FDM) processes, are restricted to depositing material in a single toolpath plane (e.g. x-y plane). The focus of this study was to explore the feasibility of integrating commercial off the shelf (COTS) additive manufac-turing technologies with a six degree of freedom industrial robot arm to yield a 3D additive manufacturing system with the capability to perform free-form six degree of freedom fused deposition modelling. The present paper presents the development of a platform from stage 0, i.e. materials to its use, and finally a printed product with the developed extruder.

The potential of the Additive Manufacturing technologies is impeded by the surface finish obtained on the as-manufactured material. Therefore, the influence of various surface treatments, commonly applied to space hardware, on the mechanical properties of three selected metallic alloys (SS316L, AlSi10Mg, Ti6Al4V) prepared by using Selective Laser Melting (SLM) and Electron Beam Melting (EBM) additive manufacturing processes have been investigated. Within this study, SLM using EOS M400 and EOS M280 equipment and in addition EBM using an ARCAM Q20 machine have been applied for sample manufacturing. A half-automated shot-peening process followed by a chemical and/or electrochemical polishing or Hirtisation® process has been applied in order to obtain lower surface roughness compared to their as-received states. Special emphasize has been taken on their tensile, fatigue, and fracture toughness properties. In addition, their stress corrosion cracking (SCC) behaviour including microstructural analysis using HR-SEM have been investigated.

Intermetallic alloys like e.g. Iron-Aluminides, Titanium-Aluminides or Molybdenum- Silizides are prospective materials for high-temperature applications. For additive manufacturing (AM) intermetallic structural materials are particularly challenging due to their high melting points, oxygen susceptibility and low temperature brittleness. The feasibility of manufacturing intermetallic Mo-Si-B alloys with the laser additive manufacturing process of direct energy deposition (DED) is demonstrated and recent results in characterizing rapidly solidified material with respect to correlations between process, composition and microstructures are presented. The possibility to dope the material with Yttrium oxide (Y2O3) for dispersion is successfully demonstrated. Current challenges, e.g. homogenous distribution of alloying elements and applicability are addressed.

This work investigates the influence of strain rate on the stress/strain behaviour of Scalmalloy. This material is an aluminium-scandium-magnesium alloy, specifically developed for additive manufacturing. The bulk yield stress of the material processed by Selective Laser Melting is approximately 340 MPa which can be increased by heat-treating to approximately 530 MPa. These numbers, combined with the low mass density of 2.7 g/cm3, make Scalmalloy an interesting candidate for lightweight crash-absorbing structures. As this application is inherently dynamic, it is of interest to study the loading rate sensitivity, which is difficult to predict: Al-Sc alloys exhibit classic strain rate sensitivity with an increased yield stress at elevated strain rates. However, Al-Mg alloys are known to show the contrary effect, they exhibit less strength as strain rate is increased. To answer the question how these effects combine, we study the dynamic behaviour at four different strain rates ranging from 10−3 /s to 1000 /s using servo-hydraulic and Split-Hopkinson testing methods. The resulting data is analysed in terms of strain rate sensitivity of tensile strength and failure strain. A constitutive model based on a simplified Johnson-Cook approach is employed to simulate the tensile tests and provides good agreement with the experimental observations.

Fabrication of a true-3D inorganic ceramic with resolution down to nanoscale using sol-gel resist precursor is demonstrated. The method has an unrestricted free-form capability, control of the fill-factor, and high fabrication throughput. A systematic study of the proposed approach based on ultrafast laser 3D lithography of organic-inorganic hybrid sol-gel resin followed by a heat treatment enabled formation of inorganic amorphous and crystalline composites guided by the composition of the initial resin. The achieved resolution of 100 nm was obtained for 3D patterns of complex free-form architectures. Fabrication throughput of 50×10³ voxels/s is achieved; voxel - a single volume element was recorded by a single pulse exposure. After a subsequent thermal treatment, ceramic phase was formed depending on the temperature and duration of the heat treatment as validated by Raman micro-spectroscopy. The X-ray diffraction (XRD) revealed a gradual emergence of the crystalline phases at higher temperatures with a signature of cristobalite SiO₂, a high-temperature polymorph. Also, the tetragonal ZrO₂ phase known for its high fracture strength was observed. This 3D nano-sintering technique is scalable from nano- to millimeter dimensions and opens a conceptually novel route for optical 3D nano-printing of various crystalline inorganic materials defined by an initial composition for diverse applications for microdevices in harsh physical and chemical environments and high temperatures.

The aim of this study was to investigate the possibility of a freeform fabrication of porous ceramic parts through selective laser sintering (SLS). SLS was proposed to manufacture ceramic green parts because this additive manufacturing technique can be used to fabricate three-dimensional objects directly without a mold, and the technique has the capability of generating porous ceramics with controlled porosity. However, ceramic printing has yet fully achieved its 3D fabrication capabilities without using polymer binder. Except for the limitation of high melting point, brittleness and low thermal shock resistance from instinct ceramic material properties, the key hurdle lies on very poor absorptivity of oxide ceramics to fiber laser which is widely installed in the commercial SLS equipment. An alternative solution to overcome the poor laser absorptivity via improving material compositions was presented in this study. The positive effect of carbon additive on the absorptivity of silica powder to fiber laser will be discussed. To investigate the capabilities of the SLS process, 3D porous silica structures were successfully prepared and characterized.

Additive manufacturing processes offer various options to fabricate metal parts, which show numerous ecological and technological advantages compared to formative and subtractive manufacturing methods. Due to quick availability and high accuracy, they are particularly suitable to produce complex prototypes. Metal fused deposition modeling is a relatively new material extrusion additive manufacturing technique based on the widely used fused filament deposition process. This study focuses on the Inconel 625 metal filament from Markforged Inc., it consists of a mixture of metal powder and a binder system, the latter being removed during washing and sintering. In this article, the mechanical properties of printed and sintered Inconel were investigated using tensile testing specimens with three different infill patterns, solid, triangular, and gyroid, printed in flatwise and upright direction. In addition, investigations into the dimensional accuracy of the printed specimens and the sintering shrinkage were carried out. The results showed that neither the dimensional accuracy nor the sintering shrinkage was significantly influenced by the printing orientation. In the context of lightweight engineering, the structures proofed beneficial especially within the elastic region. Generally, triangular infill patterns resulted in higher stiffness, while gyroids led to more ductile specimens. A mass-related evaluation of tensile testing elucidates that with aid of the infill structures weight savings of 40 % resulted in mechanical performance decreased by only 20 % on average.

In this work SiC-Ti3AlC2 and TiC-Ti3AlC2 composites produced by additive manufacturing are investigated. The fused granules fabrication (FGF) method as one of the material extrusion additive manufacturing (MEAM) technology is used to obtain composite samples. Composites with different ratios between components and different powder:polymer ratios are investigated. The technological features of the additive formation of composites are investigated, as well as their structure and properties. The optimal sintering temperature to form the best mechanical properties for both composites is 1300 °C. The composites have a regulatable porosity. Ti3AlC2 content, sintering temperature, and polymer content in the feedstock are the main parameters that regulates the porosity of FGF samples.

The paper describes problems with the current additive manufacturing chain before considering additive manufacturing as part of a modern manufacturing chain. Additive manufacturing can be used for near net-shape for finishing, for repair or for adding special features which cannot be made with traditional manufacturing. This paper describes how STEP-NC deals with these different scenarios in terms of accuracy, multi-material and variation of slice direction. The possibilities of multi-material objects also raises questions about the design of such objects and how these need to be handled by an advanced controller. The paper also describes non-planar slicing. Curved direction and cylindrical direction are shown to improve the accuracy of curved structure additive manufacturing. STEP-NC using boundary representation has better capability of depicting complex internal structures for additive processes. By using exact model of the final product represented by STEP-NC, the paper demonstrates improvements in data size reduction, slicing accuracy, and precise manipulation of internal structure.

In this work, a xylan-based antimicrobial additive agent was prepared and aimed for uses in paper products against Escherichia coli bacteria. The derived Cationic-Xylan-grafted-PHGH (CX-g-PHGH) was successfully synthesized by graft copolymerization of cationic-xylan with guanidine polymer (PHGH) using ceric ammonium nitrate as initiator. The obtained CX-g-PHGH had maximum PHGH grafting ratio of 18.45% and efficiency of 58.45%, and showed good viscosity and thermal stability. Furthermore, the paper samples prepared in this work were reinforced obviously with the addition of CX-g-PHGH by improved mechanical properties. Compared to the reference paper without any of the xylan-derivatives, the index of tensile, tear, burst and folding endurance of the paper had increases up to 20.07%, 25.31%, 30.20% and 77.78%, respectively. Moreover, the prepared CX-g-PHGH paper exhibited an efficient antimicrobial activity against E. coli bacterial, by which a lot of applications based on the new xylan-derived additive agent obtained in this work could be found, especially in field of antimicrobial paper products against E. Coli bacteria from contaminated food.

The limitations of investment casting of cobalt-based alloys are claimed to be less problematic with significant improvements in metal additive manufacturing by selective laser melting (SLM). Despite these advantages, the metallic devices are likely to display mechanical anisotropy in relation to build orientations, which could consequently affect their performance ‘in vivo’. In addition, there are inconclusive evidence concerning the requisite composition and post-processing steps (e.g. heat-treatment to relieve stress) that must be completed prior to the devices being used. In the current paper, we evaluate the microstructure of ternary cobalt-chromium-molybdenum (Co-Cr-Mo) and cobalt-chromium-tungsten (Co-Cr-W) alloys built with Direct Metal Printing and LaserCUSING SLM systems respectively at 0°, 30°, 60° and 90° inclinations (Φ) in as-built (AB) and heat-treated (HT) conditions. The study also examines the tensile properties (Young's modulus, E; yield strength, R_P0.2; elongation at failure, A_t and ultimate tensile strength, R_m), relative density (RD), and micro-hardness (HV5) and macro-hardness (HV20) as relevant physico-mechanical properties of the alloys. Data obtained indicate improved tensile properties and HV values after short and cost-effective heat-treatment cycle of Co-Cr-Mo alloy; however, the process did not homogenize the microstructure of the alloy. Annealing heat-treatment of Co-Cr-W led to significant isotropic characteristics with increased E and A_t (except for Φ = 90º) in contrast to decreased R_P0.2, R_m and HV values, compared to the AB form. Similarly, the interlaced weld-bead structures in AB Co-Cr-W were removed during heat-treatment, which led to a complete recrystallization in the microstructure. Both alloys exhibited defect-free microstructures with RD exceeding 99.5%.

The synergic features and enhancing strategies for various photopolymerization systems are reviewed by kinetic schemes and the associated measurements. The important topics include: (i) photo crosslinking of corneas for the treatmnet of corneal deseases using UVA-light (365 nm) light and riboflavin as the photosensitizer; (ii) synergic effects by a dual-function enhancer in a 3-initiator system; (iii) synergic effects by a 3-initiator C/B/A system, having an electron-transfer and oxygen-mediated energy-transfer pathways; (iv) copper-complex (G1) photoredox catalyst in G1/Iod/NVK systems for free radiical (FRP) and cationic photopolymeriation (CP); (v) radical-mediated thiol-ene (TE) photopolymerizations; (vi) superbase photogenerator based-catalyzed thiol−acrylate Michael (TM) addition reaction; and the combined system of TE and TM usinghual wavelength; (vii) dual-wavelength (UV and blue) controlled photopolymerization confinement (PC); (viii) dual-wavelength (UV and red) selectively controlled 3D printing; and (ix) 3-wavelength selectively controlled in 3D printing and additive manufacturing (AM). With minimum mathematics, we present ( for the first time), the synergic features and enhancing strategies for various systems of multi-commponents, initiators, monomers, and under one- two- and there-wavelength light. Therefore, this Review provides not only the bridging between modeling and measurements, but also guidances for further experimantal stuides and new applications in 3D printings and additive manufacturing (AM), based on the innovative concepts (kinetics/schemes).

Synthetic polymer-based gradient foams have considered as promising category of functionally graded materials with unique properties. In this study, the carbon dioxide (CO₂) foaming technology has used for PET-PEN (Polyethylene Terephthalate - Polyethylene Naphthalate) copolymer towards porous functional materials with thermal insulation with reasonable mechanical strength. Through scanning electron microscope based morphological characterization, a potential to fabricate gradient foam structures with micro-pores has identified. It has shown that variation of post-foaming temperature can tune the pore size distribution although the very high post-foaming temperature tends to cause structural instability. Thermal measurement data set the limits of operation, confirmed by simultaneous differential scanning calorimeter and thermo-gravimetric analysis. Mechanical stress and thermal conductivity also has measured to find rationale of thermal insulation with reasonable mechanical strength and to elucidate the actual 3D grid foam of copolymer.

Background: Drought, N deficiency and herbivory are considered the most important stressors caused by climate change in the agro- and eco-systems and varied in space and time shaping a highly dynamic and heterogeneous stressful environments. This study aims to evaluate the to-mato morpho-physiological and metabolic responses to combined abiotic and herbivory at dif-ferent within-plant spatial levels and temporal scales. Methods: Leaf-level morphological, gas exchange traits and VOC profiles were measured in to-mato plants exposed to N deficiency and drought, T. absoluta larvae and their combination. Ad-ditive, synergistic or antagonistic effects of the single stress when combined were also evaluat-ed. Morpho-physiological traits and VOC profile were also measured on leaves located at three different positions along the shoot axes. Results: The combination of the abiotic and biotic stress has been more harmful than single stress with antagonistic and synergistic but non-additive effects for the morpho-physiological and VOC tomato responses, respectively. Combined stress also determined a high within-plant phenotypic plasticity of the morpho-physiological responses. Conclusions: These results suggest that the combined stress in tomato determined a “new stress state” and a higher within-plant phenotypic plasticity which could permit an efficient use of the growth and defence resources in the heterogeneous and multiple stressful environmental condi-tions.

CAD-CAE software companies have introduced numerous tools aimed at facilitating topology optimization through Finite Element Simulation, thereby enhancing accessibility for designers via user-friendly interfaces. However, the imposition of intricate constraint conditions or additional restrictions during calculations may introduce instability into the resultant outcomes. In this paper, an algorithm for updating the design variables called Adaptive Variable Design is proposed to keep the final design space volume of the optimized part always under the target value while giving the main algorithm multiple chances to update the optimization parameters and search for a valid design. This algorithm aims to producing results that are more conducive to manufacturability and potentially more straightforward in interpretation. A comparison between several commercial software and the proposed algorithm, implemented in MATLAB, is carried out to prove the robustness of the latter. By simulating identical parts under similar conditions, we seek to generate comparable results and underscore the advantages stemming from the adoption and comprehension of the proposed topology optimization methodology. Our findings reveal that the integrated enhancements within MATLAB pertaining to the topology optimization process yield favourable outcomes with respect to discretization, and the manufacturability of resultant geometries. Furthermore, we assert that the methodology evaluated within MATLAB holds promise for potential integration into commercial packages, thereby enhancing the efficiency of topology optimization processes.

Oxide additive-free α- ⇀ β-Si3N4 phase transformation of a high-purity commercial α-Si3N4 powder was investigated at 1600 to 1900 ℃ under nitrogen pressure of 980 kPa. The XRD analysis revealed that the α- ⇀ β-Si3N4 phase transformation proceeded mainly at 1900 ℃, and was completed by the extensive 1900 ℃-heat treatment for 20 h. This phase transformation temperature was 33 ℃ lower than the theoretical α-Si3N4 dissociation temperature and confirmed as completely different from that often discussed for the liquid phase sintering of α-Si3N4 powder by direct comparison with the phase transformation behavior of a reference powder, α-Si3N4 powder doped with 1 mol% Y2O3. The unique α- ⇀ β-Si3N4 phase transformation was further studied by a set of characterization techniques including elemental analysis, HAADF-STEM and STEM-EDS analyses. The results strongly suggested that the oxide additive-free α- ⇀ β-Si3N4 phase transformation was governed by the for-mation of metastable solid solution between α-Si3N4 and impurity oxygen of approximately 0.6 wt%, which promoted the dissociation below the theoretical α-Si3N4 dissociation temperature to afford thermodynamically favorable β-Si3N4. Along with the β-Si3N4 formation, the impurity oxygen was concentrated at the Si3N4 crystal grain boundaries and subsequently released from the sample via the grain boundary diffusion.

This paper presents the use of Graph Neural Networks (GNNs) to predict the tensile strength of Fused Deposition Modeling (FDM) specimens. In the present work, there are four main input parameters i.e. Infill percentage, Layer height, Print speed and Extrusion temperature while the Tensile Strength is an output parameter were considered. This study includes use of central composite design based response surface methodology to finalize the experimental layout. 3D printed specimen were manufactured as per the ASTM E8 standard on FDM printer using Polylactic Acid (PLA) as filament. Micro-tensile test were performed on the printed specimen as per ASTM E8 standard. The GNN algorithm was trained on a dataset of FDM specimens, achieving a mean squared error (MSE) of 2.47, mean absolute error (MAE) of 1.14, and R-squared value of 0.78. An adjacency matrix, which shows the connections between nodes in a graph. The obtained plot for nodes and weights in a GNN provide valuable information about the model and its performance. The results show the potential of using GNNs in predicting the mechanical properties of additively manufactured specimens and provide a promising direction for further research in this field.

To obtain a given structure in 3D building-up modes, it is necessary to use optimal surfacing modes that determine the amount of heat input in local areas. For this purpose, aluminum bronze was surfacing onto a deformed base and the structure and its characteristics in the surfacing and heat-affected zones were studied by the EBSD method. The heterogeneity of the formation of the structure in each selected zone is established, which indicates the heterogeneity of heat input in local areas of the material in one mode of surfacing. For typical cases of crystallization, a molecular dynamics simulation of crystallization processes with different heat input to the base with characteristics specified based on experimental data was carried out. It has been established that the amount of heat input determines the degree of melting and the inherited defectiveness of growing crystals. The formation of misorientation boundaries and crystallization centers of new grains is determined by the conditions of joint growth of grains with given crystallographic parameters of the computational model. Numerical calculations agree with the experimentally observed results.

The presented research article shows a functionally graded lattice as an infill structure in designing a 3D printed mechanical element—a bicycle crank arm. The authors want to answer the fundamental question: whether the functionally graded lattice structures can efficiently improve structural performance and how they can be implemented in real complex components. Intuitively, everyone senses that using such elements must bring profit. A good example might be nature, which commonly reaches for such a solution in the skeletons of animals and humans. Two aspects determine their realisations: the lack of adequate construction and analysis methods and the limitations of existing manufacturing methods. Thus, the authors used relatively simple crank arm design and design exploration methods for structural analysis. The design exploration method enabled us to find the optimum solution efficiently. A developed prototype was created utilising additive manufacturing. One of the 3D printing methods - fused filament fabrication technology for metals, allowed the prototype of a crank arm with the optimised infill to be made. As a result, the authors developed a lightweight and manufacturable crank arm showing the new construction and analysis method implementable in similar 3D printed elements.

Additive Manufacturing (AM) simplifies the fabrication of complex geometries. Its scope has rapidly expanded from the fabrication of pre-production visualization models to the manufacturing of end use parts driving the need for better part quality assurance in the additively manufactured parts. Machine learning (ML) is one of the promising techniques that can be used to achieve this goal. Current research in this field includes the use of supervised and unsupervised ML algorithms for quality control and prediction of mechanical properties of AM parts. This paper explores the applications of supervised learning algorithms - Support Vector Machines and Random Forests. Support vector machines provide high accuracy in classifying the data and is used to decide whether the final parts have the desired properties. Random Forests consist of an ensemble of decision trees capable of both classification and regression. This paper reviews the implementation of both algorithms and analyzes the research carried out on their applications in AM.

Layer-wise 3D surface morphology information is critical for the quality monitoring and control of additive manufacturing (AM) processes. However, most of the existing 3D scan technologies are either contact or time consuming, which are not capable of obtaining the 3D surface morphology data in a real-time manner during the process. Therefore, the objective of this study is to achieve real-time 3D surface data acquisition in AM, which is achieved by a supervised deep learning-based image analysis approach. The key idea of this proposed method is to capture the correlation between 2D image and 3D point cloud, and then quantify this relationship by using a deep learning algorithm, namely, convolutional neural network (CNN). To validate the effectiveness and efficiency of the proposed method, both simulation and real-world case studies were performed. The results demonstrate that this method has strong potential to be applied for real-time surface morphology measurement in AM, as well as other advanced manufacturing processes.

The current paper is focused on the rapidly developing field of nano-/micro three-dimensional production of inorganic materials. The fabrication method includes laserlithography of hybrid organic-inorganic materials with subsequent heat treatment lead-ing to a variety of crystalline phases in 3D structures. In this work, it was examineda series of organometallic polymer precursors with different silicon (Si) and zirconium (Zr) molar ratios, ranging from 9:1 to 5:5, prepared via sol-gel method. All mixtureswere examined for perspective used in 3D laser by manufacturing by fabricating nano-and micro-feature sized structures. Their deformation and surface morphology wereevaluated depending on chemical composition and crystallographic phase. The appear-ance of a crystalline phase was proven using single-crystal X-ray diffraction analysis,which revealed a lower crystallization temperature for microstructures compared tobulk materials. Fabricated 3D objects retain a complex geometry without any distortion after heat treatment up to 1400^oC. Under the proper conditions, a zircon phase (ZrSiO₄ - a highly stable material) can be observed. In addition, the highest newrecord of achieved resolution below 60 nm has been reached. The proposed prepara-tion protocol can be used to manufacture micro/nano-devices with high precision andresistance to high temperature and aggressive environment.

Cistus incanus L. (CI) has been proposed as an innovative functional supplement of food products, and hence the present study aimed to evaluate the effect of the addition of dried CI on the properties of bread. Bread was prepared from white wheat flour supplemented with the addition of 1%, 2%, 3%, 4%, and 5% of ground CI. After the completion of baking process, various characteristics of the obtained bread product, such as yield, volume, porosity, acidity, color, and texture, were evaluated. In addition, total phenolic content (TPC), ABTS radical scavenging activity, CHEL chelating power, and ability to quench OH∙ radicals were measured. The results showed that the addition of CI to bread caused a reduction in the volume of bread, but texture of the crumbs was acceptable. Acidity and moisture content of bread were found to be increased following CI enrichment. Significant changes in the ash content and the color of bread crumbs were also observed. Bread incorporated with CI was characterized by significantly higher TPC and much higher antioxidant activity, as measured by ABTS, CHEL, and OH∙ radicals, compared to control bread. Supplementation of bread with 3% CI produced a product with desirable characteristics which was also favored by consumers.

This paper presents the latest developments in microCT, both globally and locally, for supporting the additive manufacturing industry. There are a number of recently developed capabilities which are especially relevant to the non-destructive quality inspection of additive manufactured parts; and also for advanced process optimization. These new capabilities are all locally available but not yet utilized to their full potential, most likely due to a lack of knowledge of these capabilities. The aim of this paper is therefore to fill this gap and provide an overview of these latest capabilities, showcasing numerous local examples.

Additive Manufacturing (AM) provides an opportunity to fundamentally redesign components previously limited by conventional manufacturing techniques. A new process for this workflow of design, manufacture by Powder Bed Fusion (PBF) and validation is presented, to which a case study of a crank for a high performance racing bicycle is applied. Topology optimisation generated conceptually ideal geometry from which a functional design was interpreted. Design for AM considerations were employed to reduce build time, material usage and post-processing labour. PBF was employed to manufacture the parts, and the build quality assessed using Computed Tomography (CT). Static and dynamic functional testing was performed and compared to a Finite Element Analysis (FEA). CT confirmed good build quality of tall, complex geometry with no significant geometrical deviation from CAD over 0.5 mm. Static testing proved performance close to current market leaders, although failure under fatigue occurred after just 2495 ± 125 cycles, the failure mechanism was consistent in both its form and location. These physical results were representative of those simulated, thus validating the FEA. This research demonstrates a complete workflow from design, manufacture, post-treatment and validation of a highly loaded PBF manufactured component, offering practitioners with a validated approach to the application of PBF.

This study presents the manufacturing process driven development of an interlocking metasurface mechanism (ILM) for Fused Filament Fabrication (FFF) with a focus on open-source accessibility. The presented ILM is designed to enable strong contact between to planar surfaces. The mechanism consists of spring elements and locking pins which snap together when forced into contact. The mechanism is designed to optimize mechanical properties, functionality and printability with common FFF printers. The mechanisms is printed from thermoplastic polyurethane (TPU) filament which was selected for its flexibility, crucial for spring element performance and tolerances of the fabrication method. To characterize the designed mechanism a tensile test is carried out to assess the holding force of the ILM. The force-displacement profiles are analyzed and categorized into distinct phases, highlighting the interplay between spring deformation, sliding, and disengagement. The results show variations in holding forces attributed to geometric and material-related factors. The testing results are compared and discussed to a numerical simulation carried out with a frictionless approach with a nonlinear Neo–Hookean material law. The study underscores the importance of meticulous parameter control in 3D printing for consistent and reliable performance of interlocking metasurface mechanisms. The investigation leads to a scalable model of a ILM element pair with a distinct three-phase snapping characteristics ensuring reliable holding capabilities.

In recent years, in addition to the commonly known wire-based processes of Directed Energy Deposition using lasers, a process variant using the electron beam has also developed to industrial market maturity. The process offers particular potential for processing highly conductive, reflective or oxidation-prone materials. However, for industrial usage there is a lack of comprehensive data on performance, process limits and possible applications. The present study deals with this problem using the example of the high-strength aluminum bronze CuAl8Ni6. Multi-stage test welds are used to determine the physically possible process limits and draw conclusions about the suitability of the parameters for additive manufacturing. For this purpose, optimal ranges for energy input, possible welding speeds and the scalability of the process were investigated. Finally, additive test specimens in the form of cylinders and walls are produced and the hardness profile, microstructure and mechanical properties are investigated. It is found that the material CuAl8Ni6 can be well processed by wire electron beam additive manufacturing. The microstructure is similar to a cast structure, the hardness profile over the height of the specimens is constant and the tensile strength and elongation at fracture values achieved correspond to the specification of the raw material.

Rapid solidification during metal additive manufacturing (AM) leads to non-equilibrium microsegregation, which can result in the formation of detrimental phases and cracking. Most of the microsegregation models, assume a Scheil-type solidification, where the solidification interface is planar and there exists local equilibrium at the interface along with either zero or infinite solute diffusion in the respective participating phases - solid and liquid. This assumption leads to errors in prediction. One has to account for finite solute diffusion and the curvature at the dendritic tip for more accurate predictions. In this work, we compare different microsegregation models that do and do not consider finite diffusion and dendrite tip kinetics against the experiments. We also propose a method to couple dendrite tip kinetics with the diffusion module (DICTRA®) implemented in Thermo-Calc®. The models which accounted for both finite diffusion and dendrite tip kinetics matched well with the experimental data.

The COVID-19 pandemic has disrupted the supply chain for personal protective equipment (PPE) for medical professionals, including N95-type respiratory protective masks. To address this shortage, many have looked to the agility and accessibility of additive manufacturing (AM) systems to provide a democratized, decentralized solution to producing respirators with equivalent protection for last-resort measures. However, there are concerns about the viability and safety in deploying this localized download, print, and wear strategy. Several polymer-based AM processes produce porous parts, and inherent process variation between printers and materials also threaten the integrity of tolerances and seals within the printed respirator assembly. The goal of this paper is to quantitatively measure particle transmission through printed respirators of different designs, materials, and AM processes, and assess the viability of printed respirators as N95 equivalents. Results from this study show that respirators printed using desktop/industrial-scale fused filament fabrication processes and industrial-scale powder bed fusion processes have insufficient filtration efficiency at the size of the SARS-CoV-2 virus, even while assuming a perfect seal between the respirator and the user’s face. Almost all printed respirators provided <60% filtration efficiency at the 100-300 nm particle range. Only one respirator, printed on an industrial-scale fused filament fabrication system provided >90% efficiency as-printed. Post-processing procedures including cleaning, sealing surfaces, and reinforcing the filter cap seal generally improved performance, but no respirator sustained the filtration efficiency of an N95 respirator, which filters 95% of SARS-CoV-2 virus particles. Instead, the printed respirators showed similar performance to various cloth masks. While continued optimization of printing process parameters and design tolerances could be implemented to directly print respirators that provide the requisite 95% filtration efficiency, AM processes are not sufficiently reliable for widespread distribution and local production of N95-type respiratory protection without commensurate quality assurance processes in place. Certain design/printer/material combinations may provide sufficient protection for specific users, but the respirators should not be trusted without quantitative filtration efficiency testing. It is currently not advised to expect printed respirators originating from distributed designs to replicate performance across different printers and materials.

HIV diagnosis and management have often caused disruptions to the everyday life and imagined futures of people living with HIV, both at individual and social levels. This has been conceptualised, in a rather dystopian way, as ‘biographical disruption’. This paper attempts to re-cast data from interviews with 40 men living with HIV (MLHIV) in Yogyakarta and Belu, Indonesia, in a slightly more positive light. Our analysis uses the concepts of additive and subtractive resilience strategies and we show how, rather than having a purely disrupted biography, participants talked about their experiences of ‘biographical reinvention'. Study participants were recruited using the snowball sampling technique, starting from two HIV clinics in the settings. Data were collected using one-on-one in-depth interviews, and a qualitative framework analysis was used to guide step-by-step data analysis. The findings showed that despite the disruptions in their everyday life (i.e., mental health condition, work, activities, social relationships, etc.) following the HIV diagnosis and management, MLHIV in our study managed to utilise their internal assets or traits (i.e., hope, optimism, resilience) and mobilised external resources (i.e., support from families, friends and healthcare professionals) to cope with the disruptions. An interweaving of these internal assets and external resources enabled them to take on new activities and roles (additive resilience strategies) and give up health compromising behaviours (subtractive resilience strategies). These were effective for most MLHIV in our study not only to cope with the HIV repercussions and improve their physical and mental health conditions, but to think or work on a ‘reinvented’ biography which encompassed resilience, hope and optimism for better health, life and future. The findings indicate the need for HIV interventions and healthcare systems that provide appropriate support for the development and maintenance of internal assets of PLHIV to enable them to cope with the repercussions of HIV and work on a ‘reinvented’ biography.

Metal fabrications experience complex physical metallurgical processes during additive manufacturing, leading to residual stress and coarse microstructure with directional growth. It significantly affects the comprehensive performance of the fabrications, which limits the application of additive manufacturing. Ultrasonic impact treatment (UIT), as a strengthening means to assist additive manufacturing, can effectively improve the stress state and refine the microstructure and the comprehensive performance. This paper introduces the effect of UIT on AM metal fabrications on microstructure morphology, stress distribution, surface roughness, internal defects, and comprehensive performance to gain a deeper understanding of the role of UIT on additively manufactured metal fabrications, which is based on the working principle and effect of process parameters. In addition, the strengthening mechanism of UIT in additive manufacturing is described from the perspective of surface plastic deformation and substructure formation, providing support for the shape and property control of metal fabrications in the process of additive manufacturing assisted by UIT. Finally, the issues that need to be studied in depth on UIT in additive manufacturing are summarized, and an outlook on future research directions is taken.

The powder bed fusion (PBF) metal additive manufacturing (AM) method uses an energy source like a laser to melt the metal powders. The laser can locally melt the metal powders and creates a solid structure as it moves. The complexity of the heat distribution in laser PBF metal AM is one of the main features that need to be accurately addressed and understood to design and manage an optimized printing process. In this research, the dependency of local thermal rates and gradients on print after solidification (in the heat-affected zone) was numerically simulated and studied to provide information for designing the print process. The simulation results were validated by independent experimental results. The simulation shows that the local thermal rates are higher at higher laser power and scan speed. Also, the local thermal gradients increase if the laser power increases. The effect of scan speed on the thermal gradients is opposite during heating versus cooling times. Increasing the scan speed increases the local thermal gradients in the cooling times and decreases the local thermal gradients during the heating. In addition, these simulation results could be used in artificial intelligence (AI) and machine learning for developing digital additive manufacturing.

Selective Laser Melting (SLM) is an additive manufacturing technique. It allows to produce elements with very complex geometry using metallic powders. A geometry of manufacturing elements bases only on 3D CAD data. The metal powder is melt selectively layer by layer using ytterbium laser. The paper contains results of porosity and microhardness analysis made on specimens which were manufactured during specially prepared process. Final analysis helped to discover connections between changing hatching distance, exposure speed and porosity. There was no significant differences in microhardness and porosity measurement results in the planes: perpendicular and parallel to the machine building platform surface.

This study is dedicated to enhancing lithium battery performance through the utilization of porous conductive polyaniline-modified graphene composites (PMGC). Given the growing importance of green energy, coupled with the development of lithium-ion battery systems and electric vehicles, achieving high-speed charge and discharge performance has become imperative. Traditional approaches involve incorporating additives like carbon nanotubes and graphene into electrodes to improve conductivity, but they encounter challenges related to cost and aggregation issues. In this study, polyaniline (PANI), a cost-effective, stable, and conductive polymer, was explored. PMGC was formed by employing ammonium persulfate (APS) as an oxidant during PANI polymerization, simultaneously serving as a surface modifier for graphene. The study systematically investigated the impact of varying amounts of PMGC on lithium-ion battery electrodes, assessing reductions in internal resistance, aging effects, different charge and discharge rates, and cycle performance. PMGC exhibited a porous structure formed by nanoscale PANI intertwining on graphene. Various measurements, including FT-IR, TGA, Raman spectroscopy, and battery performance assessments, confirmed the successful synthesis and positive effects of PMGC. Results indicated that a 0.5% addition of PMGC led to reduced internal resistance and enhanced fast charging and discharge capacity. However, excessive PMGC adversely affected aging and self-discharge. The study provides valuable insights into optimizing PMGC content for improved lithium battery performance, presenting potential advancements in energy storage systems and electric vehicles.

Advancements in 3D printing technologies have led to new implementations in rapid prototyping, microfluidics, tooling, dentistry, biomedical devices, drug delivery, and tissue engineering. Stereolithography techniques, which are photopolymerization-based processes, contribute to the optical, chemical, and mechanical properties of 3D printed materials using versatile polymer chemistry. This study used potassium titanate powder (K2Ti8O17) as an additive to enhance the mechanical strength of photocurable resins. PEG was selected as the stabilizer to optimize the dispersion and precipitation of potassium titanate. The flexural strength, hardness, and tensile strength were compared to assess the mechanical strength of the 3D printing resin. The flexural strengths of the printed specimens were in the range of 15–39 N/mm2. The measured surface hardness and tensile strength were 41–80 HV and 2.3–15 N/mm2, respectively. The output resolution of the potassium titanate/acrylate resin was tested using a line-pattern structure. 3D printing resin without stabilizers produced lines with a thickness of 0.3 mm, whereas 3D printing resin containing a stabilizer produced lines with a thickness of 0.2 mm. The flexural strength and pattern thickness results suggest that the potassium titanate/acrylate resin can be utilized as a 3D printer resin, suggesting new possibilities for potassium titanate materials.

A formula for the turbulent Prandtl number is derived in terms of local variables available from two-equations turbulence models. The derivation is a direct consequence of the expected square additivity of the molecular and turbulent parameters defining the effective viscosity and the effective conductivity. The formula does not degenerate and leads to a Kays like formulation if approximated. Its utility and its limitation are discussed.

One of the major limitations of the current 3D-concrete-printing technology is incorporation of reinforcement. Furthermore, there is a need to decrease the ecological footprint of printable concrete. As a possible solution for these challenges, this paper presents a 3D-printable strain-hardening geopolymer composite (3DP-SHGC) that shows pseudo-ductile behaviour under direct tension. The developed 3DP-SHGC is composed of one-part (just-add-water) geopolymer binder made of slag (GGBFS), fly ash (FA) and solid activator. The one-part geopolymer binder eliminates the need for elevated temperature curing and handling of corrosive alkaline liquids. At first, an optimum matrix was identified by studying the effects of FA to GGBFS ratio on the rheological properties and compressive strength. Subsequently the optimum matrix was reinforced by PVA fibres to make the 3DP-SHGC, which printing performance and rheological properties were evaluated. In addition, the influences of curing temperature on the compressive, flexural and tensile performances of the printed specimens were also investigated. The results were compared with those obtained for the mould-cast specimens. The 3DP-SHGC exhibited superior flexural performance, higher tensile strength, and comparable tensile strain capacity to the mould-cast counterpart. Further, the curing temperature had influence on the mechanical properties of both 3D-printed and mould-cast SHGCs. The underlying reasons for the differences are discussed.

Additive manufacturing (AM) is a promising new technology that is having a very fast growth from home workshops to high-tech cutting-edge factories. As any manufacturing technique, adequate metrology services are needed to assure the quality of items manufactured by AM. One of the most widely used instruments to measure the characteristics of surfaces manufactured with AM is the confocal microscope. In this paper, authors present a whole calibration procedure for confocal microscopes designed to be implemented preferably in workshops or industrial environments rather than in research and development departments. Because of that, it is as simple as possible. The procedure is designed without forgetting any of the key aspects that need to be taken into account and based on classical reference material standards. These standards can be easily found in industrial dimensional laboratories and easily calibrated in accredited calibration laboratories.

Design for Manufacture and Assembly (DfMA) in architectural, engineering, and construction (AEC) industry is attracting the attention of designers, practitioners, and construction project stakeholders. Digital fabrication (Dfab) and design for additive manufacturing (DfAM) practices are found in current needs for further research and development. The DfMA's conceptual function is to maximize the process efficiency of Dfab and AM building projects. This work reviewed 171 relevant research articles over the past few decades. The concept of DfMA and the fundamentals of DfMA in building and construction were explored. In addition, DfMA procedures associated with Dfab and DfAM, as well as its AM assembly process, were discussed. Lastly, the current machine learning research on DfMA in construction was also highlighted. Large research gaps in the DfMA for Dfab and DfAM can be filled to increase operational efficiency and sustainable practices.

Cement-free concrete has superior physical performance, such as strength and durability, compared to OPC concrete, however, it has the disadvantage of large shrinkage. Large shrinkage can cause cracks due to shrinkage stress in the long term. In this study, a shrinkage reducing agent (SRA) was used to reduce the shrinkage of cement-free mortar; its content was increased from 0.0 to 1.5 %. For an SRA content of 1.0 %, a calcium sulfoaluminate (CSA) expansive additive (EA) (2.5, 5.0, and 7.5%) was added. To calculate the shrinkage stress of cement-free mortar using the SRA and EA, the compressive strength, elastic modulus, and total and autogenous shrinkage were measured. The unit shrinkage stress of cement-free mortar was obtained by multiplying the elastic modulus by the length change and accumulated to obtain the shrinkage stress acting on the mortar according to the age. The shrinkage stress of cement-free mortar showed different tendencies as the age increased. At early ages, the shrinkage rate of the mortar occupied a large proportion of the shrinkage stress. In the long term, the shrinkage stress was significantly affected by the elastic modulus. As a result, SRA was found to be effective in reducing the shrinkage stress by decreasing both the elastic modulus and shrinkage. However, EA increased the shrinkage stress over the long term due to an increase in elastic modulus even though it compensated for early-ages shrinkage.

In this research, a screw-barrel system was designed and implemented, coupled with material extrusion, to print high-melt-temperature thermoplastic materials. The aim was to integrate two methods: the direct extrusion of thermoplastic polymer pellets with material extrusion,utilize various polymers in the form of pellets, especially high melt temperature ones, instead of traditional filaments. This addresses one of the significant challenges in filament preparation for various materials that are not readily available in the market or nearly impossible to fabricate (such as highly filled plastics). First, the screw-barrel assembly performance and factors influencing feed rate were evaluated. Subsequently, specimens were printed with polyether ether ketone (PEEK), an advanced plastic material known for its outstanding mechanical properties, high-temperature tolerance, and broad applications in various sectors, such as medical. Additionally, the material was reinforced with 2.5% continuous glass fibers while printing, which presented a novel product. Upon comparing theoretical values with experimental data from the tensile testing, a notable observation emerged: the inclusion of 2.5% glass fibers led to an approximate 43% increase in the tensile strength of the material. Furthermore, SEM images provided visual evidence of satisfactory adhesion between layers and fibers.

Literature review indicates that the basic microstructure of Ti-6Al-4V is bimodal which consist of two phases: α + β, and it occurs after the fabrication in conventional methods such as casting, plastic forming or machining processes. After the additive manufacturing methods, there could be significant changes in the microstructure. Due to the rapid heat exchange during heat-treatment process, bimodal microstructure transforms into lamellar microstructure which consists of two phases α′ + β. Despite applying optimum printing parameters, 3D-printed products exhibit typical surface defects and discontinuities. Recently, two of the primary technologies for the improvement of surface layer properties of titanium alloys are shot peening and electropolishing. Literature review signalizes that shot peening and electropolishing processes have positive impact on the corrosion behaviour, mechanical properties and the condition of the surface layer of titanium alloy. Furthermore, there is a lack of studies about combining shot peening and electropolishing in one hybrid process on titanium alloys, which could synthesize the benefits of both processes. The scope of future investigation is also included in this review.

The rapid expansion of livestock production sector to meet the world population demand is posing a big challenge to environmental sustainability. Plant-based feed additives extracted from food by-products could potentially result in a double outcome: improving animal zootechnical performances and mitigating environmental impacts of meat production chains. This presented study was carried out to assess the environmental impacts of the supplementation of a commercial Citrus extract feed additive (CEFA) in swine and broiler farming. Life cycle assessment (LCA) was applied to assess the impact of manufacturing and distributing 1 bag of 25 kg of CEFA and its use in feed in broiler and swine productions. With regard to CEFA manufacturing and distribution, results showed that the majority of impact came from the production of CEFA ingredients, accounting for 70% impact generated. The remaining 30% effect was divided to transportation to customer (25%), CEFA packaging (3%), CEFA manufacture, and production loss (2%). When enlarging the scope, the use of CEFA in piglet and broiler diets showed improving the measured environmental indicators, compared to such standard systems. Indeed, feed supplemented CEFA have demonstrated in elevating zootechnical performances, hence saving feed consumed. Consequently, that helped reduce environmental issues from animal feed ingredients’ agriculture. To be more specific, the supplementation of 25 kg of CEFA in feed led to a reduction of 6 tons of CO2 emitted along the life cycle of broiler production and 5 tons in the case of fattening pig. 0.7 hectares of land used had been saved as well as, 201 m3 of water (broiler) and 82 m3 (swine) were economized. Environmental performance assessment showed the interest in using this CEFA in swine and broiler diets to mitigate the environmental impacts.

Biogas production from organic waste is a promising renewable energy source, but achieving optimal production and digester stability can be challenging. This study investigated the impact of the Evogen microbial additive on biogas production and digester quality through microbial abundance and physicochemical parameter analysis. Two biogas plants, BG01 and BG02, were examined using 16S rRNA profiling to assess microbial abundance. Simultaneously, physicochemical parameters, including FOS/TAC ratio, total solids, volatile solids, biogas production, and VFA profile, were measured to evaluate digester performance. Results revealed distinct microbial community shifts in Evogen-treated digesters. Increased abundance of methanogenic archaea and hydrolytic bacteria indicated improved anaerobic digestion. Evogen supplementation also positively affected digester performance, with higher FOS/TAC ratios indicating enhanced acidification and methanogenesis. Reductions in total solids and volatile solids demonstrated improved organic matter degradation. Significantly higher biogas production was observed in Evogen-treated digesters, highlighting its potential as a microbial additive. Furthermore, VFA profiling demonstrated improved process stability and reduced substrate inhibition in Evogen-treated digesters. In summary, Evogen microbial additive positively influenced microbial dynamics, improving biogas production and digester quality. These findings contribute to optimizing biogas production systems and understanding the complex microbial interactions within anaerobic digesters.

Less than half of e-waste plastics is sorted worldwide and this rate is likely to decline as major processing countries have banned importation of e-waste plastics. This forces the development of decentralized processing facilities, also known as microfactories. The present work investigates the recyclability of different grades of acrylonitrile-butadiene-styrene (ABS) copolymer, polycarbonate, and polypropylene, which were found to be very abundant in a recycling site in the UK. The determination of the matrix relied on the resin identification code imprinted in the e-waste plastic and subsequent FTIR analysis. The melt-blend extrusion technology enabled the valorization of the wasted thermoplastics as 3D filament without significant degradation of the polymers. The recycled materials maintained the tensile strength around 2.5 MPa in agreement with the specifications offered by virgin polymers. Further characterization was done by means of laser microscope, thermogravimetric analysis, and XRF to determine the commercial viability of the recycled filament. A modified solvent-based method was developed with acetone to remove the brominated flame retardants: 25g/100mL, 30 minutes of contact time, and 4 extraction steps. The FTIR results show that the degradation of the rubbery dispersed phase corresponding to the butadiene can be accumulated in the less soluble fraction of the waste ABS.

This literature review provides an in-depth exploration of the research conducted on the investigation and measurement of residual stress (RS) in Wire Arc Additive Manufacturing (WAAM) products, particularly focusing on how process parameters influence the phenomenon. RS plays a crucial role in determining the mechanical behavior and structural integrity of WAAM components. This review article gives an understanding of the relationship between process parameters and RS to optimize the WAAM processes and ensure the durability of the final products. It also summarizes key findings, measurement techniques, challenges, and future directions in this evolving field. The review also analyzes a measurement of RS in the products of WAAM as a function of process parameters depending on examining various research studies, techniques, and methodologies employed in their studies. Experimental measuring techniques and numerical analysis of RS to determine the impacts of RS in mechanical response in products of WAAM were discussed. By offering a comprehensive overview of current research trends and insights, this review serves as a valuable resource to guide future investigations, fostering the advancement of WAAM as a robust and efficient manufacturing technology.

Direct Energy Deposition (DED) is a versatile and efficient method in metal additive manufacturing. However, humping, caused by abnormal dynamics in the melt pool (MP), poses a significant threat to the geometric integrity of manufactured products. Current state-of-the-art (SOTA) methods primarily detect humping by analyzing late-stage spatial abnormalities, such as MP detachment. This approach is fundamentally reactive, leading to a tendency to miss early humping spatiotemporal dynamics, like cyclic elongation of the MP. This study introduces a novel, proactive indicator named VIMPS (Variability of Instantaneous MP Solidification-Front Speed), a physics-based tool designed to quantify early abnormal fluctuations in MP solidification speed. The experiments demonstrate VIMPS correlation with humping-induced geometric inaccuracies. By capturing early spatiotemporal dynamics of the MP, VIMPS reduces detection latency by 30 seconds compared to existing SOTAs that focus solely on spatial abnormalities. This significant improvement transforms detection from reactive to proactive, providing the time needed for corrective actions to enhance the overall productivity and quality of the DED process.

The main development direction of energy efficiency technologies in construction is the creation of various materials with a complex structure and unique strength, thermal and other properties. The aerogel is a material with high porosity and excellent thermal insulation properties. This paper provides the state-of-the-art of aerogel applications for the additive manufacturing of energy efficient buildings. This work provides the experimental and numerical assessment results of thermal conductivity of aerogel-enhanced blanket, the experimental assessment results of thermal performance of aerogel-enhanced building structure, the experimental assessment results of the aerogel application as mixture powder component of the concrete mixture to printing building and the experimental assessment results of the aerogel application as parget powder component. Experimental results show the effect of aerogel powder component application: thermal conductivity decreased by 25%.

Electronic devices are sensitive to electromagnetic (EM) emissions requiring electromagnetic shielding protection to assure good operation, preventing noise, malfunctioning, or even burning. To assure protection, it is important to develop suitable material and design solutions for electronic enclosures. Most common enclosures are made with metal alloys by traditional manufacturing methods. However, resourcing to thermoplastic composites combined with additive manufac-turing (AM) technologies emerges as an alternative that enables to fabricate complex parts that are lightweight, consolidated and oxidation and corrosion resistant. In this research, an AM technique based in material extrusion was used to print 2 mm thick specimens with a multi-material made of micro-carbon fiber (CF) filled polyamide, reinforced, at specific layers, by continuous carbon fibers stacked with a 90° rotation to each other. Specimens electromagnetic shielding effectiveness (EMSE) was evaluated in the frequency band of 0.03 – 3 GHz by coaxial transmission line method. De-pending on the number of CF layers, the EM shielding obtained can up to 70 dB, with a specific shielding up to 60 dB.cm3/g, predominantly by absorption mechanism, being 22 times higher that without the CF layers. These findings fundament this innovative approach for lightweight cus-tomizable solutions for EM shielding applications.

The need for Artificial Intelligence (AI) and Machine Learning (ML) technologies is increasingly being leveraged for optimizing Data centers’ (DCs’) operations as the volume of operations management data increase tremendously. These strategies can assist operators in better understanding their DC operations and making informed decisions up front to preserve service reliability and availability. Aiming at creating models that optimize energy efficiency, identify inefficient resource utilization and scheduling policies, and predict outages. Apart from model hyperparameter tuning, feature selection is a crucial step to identify relevant features with the objective of providing insight into the data, improving performance, and reducing computational expenses. Although several feature selection methods have been discussed in various domains, none have been discussed in the context of the data center. This paper introduces SHapley Additive exPlanation (SHAP), a class of additive feature attribution values-based feature selection that is rarely discussed in literature. We compared the effectiveness of SHAP method with several widely used methods. We used a real DC dataset obtained from the ENEA CRESCO6 cluster with 2,0832 cores to evaluate the methods. To demonstrate the comparison of the methods, we picked the top 10 most important features from each method, the predictions were retrained, and their performance was evaluated using MAE, RMSE, and MPAE. The results show that the SHAP-assisted feature selection performed best and align with human intuition.

The power conversion efficiency (PCE) of polymer solar cells (PSCs) are strongly depended on the bulk-heterojunction active layer. Here, the 1,8-diiodooctane (DIO) additives have been added into the PCDTBT: PC70BM blend PSCs. Based on the higher boiling point than host solvent ODB and better solubility of PC71BM, the device photovoltaic properties with DIO additive were changed obviously. The investigations of EQE indicate that the DIO can influence the charge recombination and transportation process, and absorption studies demonstrate that the charge carriers generation process can also be affected by DIO. The overall impact reflected on the decreased equivalent resistant. With 3% v/v DIO, the Jsc, Voc and FF are both increased. Correspondingly, a highest PCE is achieved of 6.15%, while the reference device without DIO only has a PCE of 5.23%. Hence, adding DIO solvent additive is a effective method for the photovoltaic properties improving of PCDTBT: PC70BM blend PSCs.

This paper presents a physical and mathematical model that has been developed in the framework of the approach used in the computational mechanics of materials. The model is designed to enable the study of the patterns of deformation and fracture of ceramic composites with a transformation-hardened matrix that are obtained by additive technologies at the mesoscopic and macroscopic levels under intense dynamic loading. The influence of the loading rate on the formation of the fracture and energy dissipation fronts for composite materials, based on the Al2O3 20%ZrO2 system, is shown. Nonlinear effects under intense dynamic loading in the considered composites are associated with the processes of self-organization of structural fragments at the mesoscopic level, as well as the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

This paper describes a multi-channel in-situ monitoring system developed to better understand defect formation signatures in metal additive manufacturing. Three high-speed imaging modes coupled with an image computer capable of processing and storing these data streams allowed an examination of defect formations signatures and mechanisms. It was found that defects later detected in X-ray computed tomography (CT) scans were related to regions with anomalous heat signatures and powder bed morphology. Automated defect detection algorithms based on these defect signatures captured 80% of defects greater than 300 µm.

It is a common practice to detect outliers in a financial time series in order to avoid the adverse effect of additive outliers. This paper investigated the performance of GARCH family models (sGARCH; gjrGARCH; iGARCH; TGARCH and NGARCH) in the presence of different sizes of outliers (small, medium and large) for different time series lengths (250, 500, 750, 1000, 1250 and 1500) using root mean square error (RMSE) and mean absolute error (MAE) to adjudge the models. In a simulation iteration of 1000 times in R environment using rugarch package, results revealed that for small size of outliers, irrespective of the length of time series, iGARCH dominated, for medium size of outliers, it was sGARCH and gjrGARCH that dominated irrespective of time series length, while for large size of outliers, irrespective of time series length, gjrGARCH dominated. The study further leveled that in the presence of additive outliers on time series analysis, both RMSE and MAE increased as the time series length increased.

Although distributed additive manufacturing can provide high returns on investment the current markup on commercial filament over base polymers limits deployment. These cost barriers can be surmounted by eliminating the entire process of fusing filament by 3-D printing products directly from polymer granules. Fused granular fabrication (FGF) (or fused particle fabrication (FPF)) is being held back in part by the accessibility of low-cost pelletizers and choppers. An open-source 3-D printable invention disclosed here provides for precise controlled pelletizing of both single thermopolymers as well as composites for 3-D printing. The system is designed, built and tested for its ability to provide high tolerance thermopolymer pellets from a number of sizes capable of being used in a FGF printer. In addition, the chopping pelletizer is tested for its ability to chop multi-materials simultaneously for color mixing and composite fabrication as well as precise fractional measuring back to filament. The US$185 open-source 3-D printable pelletizer chopper system was successfully fabricated and has a 0.5 kg/hr throughput with one motor, and 1.0 kg/hr throughput with two motors using only 0.24 kWh/kg during the chopping process. Pellets were successfully printed directly via FGF and indirectly after being converted into high-tolerance filament in a recyclebot.

The paper investigates the influence of ion nitriding on the microstructure, corrosion resistance, and tensile strength at elevated temperatures of Haynes 282 nickel superalloy specimens produced by the Direct Metal Laser Sintering-DMLS technique. Analysis of the specimens’ surface morphology revealed that the ion nitriding process significantly affects the physical and chemical phenomena occurring on the surface of the specimens. Phase composition and stress analysis showed that Haynes 282 nickel alloy specimens produced by the DMLS technique and a chromium nitride layer produced in the ion nitriding process have tensile stress. The layer is also characterized by high nanohardness compared to specimens produced using the classical method (wrought) and DMLS technique. The conducted corrosion resistance tests confirmed the positive effect of the nitrided layer on the corrosion resistance of Haynes 282 nickel alloy produced by the DMLS technique. The ion nitriding process did not significantly affect the elevated-temperature tensile strength of Haynes 282 nickel alloy specimens produced by the DMLS technique.

Edible films were produced combining pectin (P) matrix with chitosan nanoparticle (CSNP), polysorbate 80 (T80), and garlic essential oil (GEO) as an antimicrobial agent. The CSNP were analyzed for their size and stability, and the films, throughout their contact angle, scanning electron microscopy (SEM), mechanical and thermal properties, WVP and antimicrobial activity. Four filming-forming suspension were investigated: PGEO (control); PGEO@T80; PGEO@CSNP; PGEO@T80@CSNP. The average particle size was 317nm with zeta potential reaching +21.4 mV, which indicated colloidal stability. The wettability of the films exhibited values of 65°, 43°, 78°, 64° respectively. In antimicrobial tests, the films containing GEO showed inhibition only by contact for S.aureus. For E. coli, the inhibition occurred only in films containing CSNP and by direct contact in the culture. The results indicate a promising alternative for designing stable antimicrobial nanoparticles for application in novel food active packaging.

This article explores the cutting-edge advancement of gypsum and cement building boards infused with shape-stabilized n-octadecane, an organic phase change material (PCM). The primary focus is on improving energy efficiency and providing electromagnetic interference (EMI) shielding capabilities for contemporary buildings. The research investigates the integration of these materials into construction materials, using red-mud Carbon Foam as a stabilizer for n-octadecane (OD@CCF). Various analyses, including microstructural examination, porosity assessment, and additive dispersion, were conducted using X-ray microtomography and density measurements. Thermal conductivity measurements demonstrated the enhancement of composite boards as the OD@CCF content increased, while mechanical tests indicated an optimal additive content of up to 20%. The thermal-regulated capabilities of these advanced panels were evaluated in a custom-designed room model equipped with a homemade environmental chamber, illustrating a consistent temperature environment during heating and cooling cycles. The incorporation of OD@CCF into cement boards exhibited improved thermal energy storage properties. Moreover, the examined composite boards displayed efficient electromagnetic shielding performance within the frequency range of 3.2–7.0 GHz, achieving EMI values of approximately 18 and 19.5 dB for gypsum and cement boards, respectively, meeting the entry-level value required for commercial applications.

This study was carried out with a low-cost electronic nose prototype based on eight metal oxide sensors (MQ) in order to characterize samples of lemons treated with 0.5% and 0.1% of sodium benzoate. The MQ sensors designed are sensitive to one or more chemicals to detect the presence of a variety of chemicals in the air. The sensor MQ135 detects ammonia, hydrogen sulphide and benzene. Signal data were studied to obtain a pattern recognition of rotten in lemon fruits. Network analysis was used to obtain a calibration of measures among the stage of lemons. In this article, an electronic nose prototype based on 8 MQ metal oxide sensors has been used in order to analyze and characterize different lemon varieties to which different chemical treatments have been applied in pre-harvest. PCA-based data analyzes were used to observe clusters in the data. Through the combined use of the data obtained by the nose and these Sequential Neural Networks (SNNs) a classification tool for lemon varieties and applied treatments has been obtained. It is shown the ability of this device to be used as a reliable discrimination method, in addition to providing low cost and optimization of time and expert resources.

Ceramic composites have good strength, fracture toughness and hardness characteristics and are widely used in industry, medicine. The properties of ceramic composites can be controlled at the production stage by setting the internal structure. This is made possible by the development of additive manufacturing. However, not all properties are well understood, especially dynamic fracture resistance and fracture toughness. In order to predict the mechanical behavior of ceramic composites in the manufacturing phase with a controlled structure under dynamic loads, it is convenient to use methods of numerical analysis. The aim of this work was to investigate the influence of loading speed and internal structure on dynamic resistance and fracture toughness of ATZ nanocomposites. Within the framework of the study physical and mathematical model that is used in computational mechanics of materials is developed. In the paper is shown the influence of the loading rate on the strain rate in the region of the shock transition for materials based on ZrO2 - Al2O3 system. The research shows nonlinear effects under intense dynamic loads in the shown composite materials are bound up with either the processes of self-organisation of deformation modes at the mesoscopic level or the occurrence of martensitic phase transformations in matrix volumes adjacent to the strengthening particles.

In this study, additive manufacturing of reinforced parts using metallic wire as both a reinforcement component and a shape memory stimulus through Fused Deposition Modeling (FDM) was investigated. A Shape Memory Polymer (SMP) restores its original shape and recovers it upon specific stimuli. This research employed chromium-nickel metal wire as a reinforcing component to enhance mechanical properties and introduce the capability for thermal stimulation of polylactic acid (PLA) via electrical current using the "in-situ impregnation" method within FDM process. Reinforced specimens were fabricated with wire with two diameters of 0.1 and 0.15 mm, along with two volume percentages of 5 and 10. Comprehensive evaluations encompassing mechanical (tensile and flexural) and thermal properties of the printed specimens were conducted. The outcomes revealed a significant enhancement in both tensile and flexural properties of the polymer matrix due to the embedding metallic wire, even under elevated temperatures during bending test. Furthermore, the thermal properties of the reinforced specimens were examined by subjecting them to various voltages, resulting in temperature ranging from 36.4 to 150.1°C. These findings highlight the ability to tailor a wide range of mechanical properties and shape recovery in the reinforced specimens by carefully selecting the wire volume fraction, voltage, and wire diameter, thus regulating the materials properties with specific application requirements.

Investment management is a common process and practice used for achieving a desirable investment goal or outcome. Investment assessment should be carried out at various stages of project realization in accordance with capital investment volume. Investment risk management implies the effective control of all procedures and monitoring of risks in all phases of the investment project. Because of the reason that a single indicator in probability calculation of achieving optimal return from the investment does not exist, performing sufficiently reliable estimates of the quality of investments becomes a tedious task. There are many indicators, factors, and criteria required for consideration to reach the effective solution of the investment problem. Unfortunately, the systematic variation of economic situations in the marketplace stipulates the continuous and frequent changes of investment conditions and environment in which the investor should act and operate. Hence, the rules required for providing a reasonable quality of investment projects can be based only on investor’s management strategy and rely on investor’s intuition and practice. The importance of classification in investment management and decision making process is undeniable. The objects to be classified are described using assessments in accordance with various criteria which can be both quantitative and qualitative. With a competent formulation of the investment process, both methods are used in parallel. There exist various decision making approaches for the investment management, and simple additive weighting (SAW) is one of the well-known multi-criteria decision making (MCDM) methods aiming to provide an optimal decision for decision maker when solving various real-life problems, and particularly, investment problem. In this paper, fuzzy simple additive weighting (FSAW) method in group decision making is applied to undertake the capital investment expenditure for purchasing cars with the purpose of renting them to the public. The development of existing FSAW method is accomplished and this process involves the sensibility of outcomes to changes in the rate of fuzziness represented with decisions taken. Eventually, the degree of fuzziness involved in an analysis that directly attempts to model the immanent vagueness and imperfectness in particular precedency judgments made, is determined. A numerical example illustrates the importance and effectiveness of the suggested approach with the aim of ranking alternatives and hence, determining the most preferred alternative in MCDM problem.

Applying of blood biopolymers to regulate the phase composition is promising in designing the hydroxyapatite-based hybrid biomaterials with controllable resorbability. Hybrid materials based on hydroxyapatite and platelet-poor plasma (PPP) were formed in conditions of chemical precipi-tation at pH 11, [Ca2+] / [PO43–] ratio 1.67, PPP volume fraction of 6–24%, maturing time of 4–9 days. Mineral component of the materials was represented as 53% hydroxyapatite / 47% amor-phous calcium phosphate after 4 days of maturation, and 100% hydroxyapatite after 9 days of maturation. Varying PPP content from 6% to 24% provided forming of materials with rather de-fined content of amorphous calcium phosphate and biopolymer component, having desired mor-phology ranging from typical apatitic conglomerates to hybrid apatite-biopolymer fibers. Co-precipitated hybrid materials based on hydroxyapatite and PPP are promising for bone regen-eration in osteoplastic and maxillofacial applications.

Surfaces of additively manufactured metal parts from powder-based processes typically show powder particle agglomerations and other features, resulting in high surface roughness. Proper characterization of those surfaces is necessary in order to assess part quality with respect to coatability, mechanical performance or corrosion resistance for use in aerospace, automotive, medical and more industrial applications. Optical surface texture measurement allows for collection of areal surface data, while the established contact stylus method only captures line profile data. When applying optical methods for surface topography measurements, proper data acquisition and post-processing in order to assess surface texture may be complex. A number of variables can be adjusted, such as different measurement settings, approaches to outlier removal, evaluated area size or form removal. This work shows the influence of selected z-range prior to measurement and the influence of choosing pre-defined outlier removal settings in MountainsMap 9.2 on selected ISO 25178-2:2022 parameters calculated from data obtained from confocal microscopy for as-built Ti6Al4V from laser powder bed fusion. The aim is to show the influence of variation in measurement and post-processing on calculated surface texture parameters and stress the importance of proper documentation in order to achieve reproducibility of data for quality management.

We report the influence of ammonium hydroxide (NH4OH), as growth additive, on zinc oxide nanomaterial through the optical response obtained by photoluminescence (PL). A low-temperature hydrothermal process is employed for the growth of ZnO nanowires (NWs) on seedless Au surface. A more than two order of magnitude change in ZnO NW density is demonstrated via careful addition of NH4OH in the growth solution. Further, we show by systematic experimental study and PL characterization data that the addition of NH4OH can degrade the optical response of ZnO NWs produced. The increase of growth solution basicity with the addition of NH4OH may slowly degrade the optical response of NWs by slowly etching its surfaces, increasing the point defects in ZnO NWs. The present study demonstrates the importance of growth nutrients to obtain quality controlled density tunable ZnO NWs on seedless conducting substrates.