To realize the utilization of peanut shell, this study investigates the combustion behavior, chemical kinetics, and thermodynamic parameters of peanut shell using TGA under atmospheric air. Results indicate that increasing the heating rate leads to higher ignition, burnout, and peak temperatures, as observed in the TG/DTG curves shifting to the right. Analysis of combustion performance parameters suggest that higher heating rates can enhance combustion performances. Kinetic analysis using two model-free methods, KAS and FWO, shows that the activation energy (Eα) ranges from 93.30 to 109.65 kJ/mol for FWO and 89.72 to 103.88 kJ/mol for KAS. The data fit well with coefficient of determination values (R2) close to 1. Pre-exponential factors using FWO range from 2.19×106 to 8.06×107 s–1, and for KAS range from9.72×105 to 2.25×107 s–1. Thermodynamic analysis indicates a low-energy barrier (≤ ±6 kJ/mol) between activation energy and enthalpy changes, suggesting easy reaction initiation. Furthermore, variations in enthalpy (ΔH), Gibbs free energy (ΔG), and entropy (ΔS) upon conversion (α) suggest that peanut shell combustion is endothermic and non-spontaneous, with the generation of more homogeneous or well-ordered products as combustion progresses. These findings offer a theoretical basis and data support for the further utilization of agricultural biomass.

In order to study the adsorption process and adsorption characteristics of shale oil at the macro scale, the isothermal adsorption experiments of illite and kerogen on heptadecane (oil phase) solution were carried out by infrared spectrophotometry and gas chromatography-mass spectrometry. The reaction mechanism of alkane solution concentration and temperature in the adsorption process was investigated. The adsorption characteristics of heptadecane on the surface and pores of illite and kerogen were elucidated by adsorption isotherm model and adsorption thermodynamic model. The results show that: The concentration of alkane solution contributes to the adsorption of illite and kerogen. As the concentration of the solution continues to increase, the adsorption rate gradually slows down. However, the temperature hardly affects the adsorption rate. At 25℃, 50℃ and 60℃, the adsorption process of illite on alkane solution is more consistent with Langmuir model and Freundlich model, respectively. The difference is that Langmuir model is suitable for describing the whole adsorption process of kerogen on alkane solution. 3) The adsorption process of illite and kerogen to heptadecane solution is an endothermic reaction. Heating helps to accelerate the migration rate of alkanes, which is conducive to the adsorption reaction. The research results clarify the adsorption characteristics of shale oil heavy components from the macro level, and fill the research gap in the application of solid-liquid isothermal adsorption physical experiments to the adsorption and occurrence of shale oil.

This study presents a comprehensive investigation into the spectrum and determinants of child abuse and neglect in Nkpor-Uno, a community in Anambra State, Nigeria. Through a descriptive surveys design, the study explores various forms of abuse and neglect experienced by children, as well as the underlying factors contributing to these phenomena. The population for the study consisted of 1000 parents/ caregivers who are residents of Nkpor-uno. The sample for the study consisted of 100 respondents, purposive sampling techniques was used for the study. The questionnaire was a self-designed structured questionnaire. Data collected were analyzed using frequency, mean and standard deviation. Findings reveal alarming prevalence rates of child maltreatment, including physical, emotional, sexual abuse, and neglect. Socioeconomic factors such as poverty, parental substance abuse, family dynamics, and inadequate sex education emerged as significant contributors to child maltreatment. The study underscores the urgent need for targeted interventions and support systems to address the root causes of abuse and neglect and safeguard the well-being and development of children in Nkpor-Uno. By raising awareness, enhancing access to resources, and promoting positive parenting practices, we can strive towards building a safer and healthier environment for children, ensuring they are protected from harm and given the opportunity to thrive.

From the theory of relativistic chemical kinetics [M. W. Baig, Int. J. Mod. Phys. B 31, 1750177 (2017)] relativistic thermodynamics and kinetics for electrode processes have been developed to explain time dilation for electrode processes. For a moving observer moving at fractions of the speed of light, cell potential is observed to decrease. This results in the slower oxidation and reduction of ions at the respective electrodes. The newly formulated Lorentz transformation of the electrode and cell potential is explained in terms of generation of spin 2-boson “gravitons” from fusion of spin-1 boson “virtual-photons” mediating electrostatic force of attraction between ions and electrodes. It is postulated that birth of spin 2-boson i.e. gravitons is followed by their eventual escape in any of higher 4+n dimensions. To demonstrate the effectiveness of the present theory, the Daniel cell is considered as a numerical example.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

Transient conjugate heat transfer measurements under varying temperature and velocity inlet boundary conditions at incompressible flow conditions were performed for flat plate and ribbed channel geometries. Therefrom local adiabatic wall temperatures and heat transfer coefficients are determined. Those data are analyzed using typical heat transfer correlations, e.g. Nu=CRe^mPr^n determining the local distribution of C and m. It is shown that they are closely linked. A relationship lnC=A−mB is observed with A and B as modeling parameters. They could be related to parameters in log law or power law representations for turbulent boundary layer flows. The parameter m is shown to have a close link to local pressure gradients and therewith near wall streamlines as well as friction factor distributions. A normalization of the C parameter allows to derive a Reynolds analogy factor and therefrom local wall shear stresses.

Most astrophysicists today believe that the present universe was produced in a big bang. This article explores the big cycle of matter and energy in the universe, with the big bang as an important part of the cycle.The authors approve of the idea that the universe is gravitationally closed. That is, its average density is higher than the critical value. All the matter and radiation cannot fly out the closed universe.The 3k background radiation is a vast heat ocean in the closed universe, stable and eternal. It is not the afterglow of the thermal radiation of the decoupled fire ball, 380,000 years after the big bang, as many people believed so far. The big bang and the following big expansion drove the matter of more than 2×10¹² galaxies to the remote space. Their potential energies become higher and higher, while their huge kinetic energies that they derived from the big bang become smaller and smaller until drop down to zero. The galaxies will then return back one after another, passing the central region of the universe with tremendously great kinetic energies. They of course cannot all return back directly to their start point of the big bang and restore to the state of the original cosmic core. They will rush to pass the central region and fly to the other sides of the universe, and shuttle around the central part ceaselessly. From the big bang to the following expansion, to the numerous galaxies, to the more than 2×10²³ stars, and to the stars releasing huge nuclear energy due to their internal nuclear fusion each for about 10¹⁰ years, all these enormous processes are irreversible, resulting in enormous increase in entropy. These processes produce large amount of light and other radiations and pour them into the extremely vast heat ocean. These light and other radiations will also be shuttling ceaselessly in the vast heat ocean until, by their interaction with the rare dusts in the galaxies, they mingle into the 3K thermal radiation of the heat ocean. In all the galaxies, there are various black holes. Every black hole, since its birth, ceaselessly extracts the matter and radiation that approach it, and gets larger. In the above mentioned shuttling of all the galaxies, numerous stars and black holes in these galaxies have many chances to approach even meet each other. A black hole can annex other celestial bodies that it meets, including annex other black holes. All these processes carry on and on ceaselessly, resulting in the matter of these celestial bodies to concentrate again and again. The number of all the celestial bodies including the black holes reduces ceaselessly, and the mass of the survived black holes become larger, and their shuttling amplitudes become shorter. The larger black holes and the shorter amplitudes result in the rate of concentration of mass to be faster. Eventually, all the matter in the universe will be concentrated to form a tremendously large central black hole. The central black hole has an astonishingly large Schwarzschild sphere, absorbing the thermal radiation from the vast heat ocean very rapidly and ceaselessly until some threshold value of its internal energy is exceeded, and a new big bang breaks out. The black holes provide a way in the Universe to re-concentrate matter and energy again. Black holes are Maxwell’s demons in the Nature.

Nucleation is a fundamental and general process at the initial stage of first order phase transition. Although various models based on the classical nucleation theory (CNT) have been proposed to explain the energetics and kinetics of nucleation, detailed understanding on nanoscales are still required. Here we focus on homogeneous bubble nucleation, in which evaluation of the size dependence of bubble free energy is the key issue. We propose application of a formula in stochastic thermodynamics, the Jarzynski’s equality, for data analysis of molecular dynamics (MD) simulation to evaluate the free energy of bubble nucleation. As a test case, we performed a series of MD simulations with Lennard-Jones (LJ) fluid system. By applying an external spherical force field to equilibrated LJ liquid, we evaluated the free energy change during bubble growth as the Jarzynski’s ensemble average of required works. A fairly smooth free energy curve was obtained as a function of bubble radius in metastable liquid of mildly negative pressure conditions.

Renal replacement therapy (RRT), widely used in the treatment of renal injury in the course of sepsis, aims to eliminate the toxins and proinflammatory cytokines, involved in the pathomechanism underlying septic shock. Dialysis filters characterised by a high adsorption potential for cytokines in RRT when septic renal injury is the case. It is of key importance in the antibiotics treatment of sepsis to achieve desired values of PK/PD indices. Continuous renal replacement therapy (CRRT) may affect antimicrobial clearance, increasing their elimination in some cases. The aim of this study was to determine the degree of adsorption for linezolid, on three different types of filters used in CRRT. In our in vitro study a continuous veno-venous hemofiltration (CVVH) was conducted using 3 types of filters: polysulfone (PS), polyethyleneimine-treated polyacrylonitrile (PAN PEI) and non-PEI-treated polyacrylonitrile (PAN) filters. Each type of filter was used in 3 CVVH cycles, involving the use of 600 mg of linezolid dissolved in 700 ml of bovine blood or in 700 ml of 0.9% NaCl. In each case the total volume of the obtained solution was 1000 ml. Blood samples, at particular time points, were collected in order to measure drug concentration. The differences in mean drug/NaCl adsorption and drug/ blood adsorption were determined using one-way ANOVA with multiple comparisons by Tukey post-hoc test. A p-value of < 0.05 was considered to be significant. A significant adsorption of linezolid was found for PAN PEI filter, both in samples obtained from bovine blood and 0.9% NaCl solutions, at the endpoint. No significant adsorption was demonstrated on PAN or PS filters. There is a need for in vivo research to confirm the effect of filter type on linezolid concentration in patients undergoing CRRT.

With the development of the energy sector based on renewable primary sources, structural changes are emerging for the entire national energy system. Initially, it was estimated that energy generation based on fossil fuels would decrease until its disappearance. However, the evolution of CO2 capture capacity leads to a possible coexistence for a certain period with the renewable energy sector. The paper develops this concept of coexistence of the two systems, with the positioning of green hydrogen not only within the renewable energy sector but also as a transformation vector for carbon dioxide captured in the form of synthetic fuels such as CH4 and CH3OH. The paper also analyzes the economic aspects related to price differences for energy produced in the two sectors, as well as their interconnection. The technical aspect, as well as the economic one, for storage through various other solutions besides hydrogen, has been highlighted. The development of the renewable energy sector and its demarcation from the fossil fuel energy sector, even with the transcendent vector represented by green hydrogen, leads to the deepening of dispersion aspects between the electricity sector and the thermal energy sector, a less mentioned aspect in current works but of great importance.

The objective of this study was to investigate the impact of athletes' respiratory muscle strength, as assessed through maximal inspiratory (MIP) and expiratory pressure (MEP), on aerobic endurance, as indicated by maximal oxygen consump-tion (Max VO2) kinetics. Respiratory muscle strength was assessed using a digital spirometer (Pony FX Cosmed, Italy), while maximal oxygen utilization capacity was measured using a breath-by-breath automatic portable gas analysis system (Cosmed K5, Italy). Statistical analysis was conducted utilizing SPSS 22.0. Based on the standardized regression coefficients (β), it was found that MEP (mean ± SD: 130.95 ± 42.82) and inspiratory diaphragmatic circumference values significantly influenced ventilatory equivalent (VE), oxygen consumption (VO2), and carbon dioxide pro-duction (VCO2). Conversely, the remaining predictor variables did not exhibit a sig-nificant effect on VE (mean ± SD: 134.80 ± 36.69), VO2 (mean ± SD: 3877.52 ± 868.47 ml), and VCO2 (mean ± SD: 4301.27 ± 1001.07 ml). In contrast, measurements of chest circumference (mean ± SD: 91.40 ± 10.72 cm), MEP, and diaphragmatic cir-cumference during inspiration (mean ± SD: 95.20 ± 10.21 cm) were found to signifi-cantly impact Max VO2 (mean ± SD: 58.52 ± 10.74 ml/kg/min), while the other pre-dictor variables did not demonstrate a significant effect on Max VO2. Conclusively, the study revealed that measured values of diaphragmatic circumference during inspiration and MEP exerted a notable influence on Max VO2, VE, VO2, and VCO2. Our findings underscore the importance of considering respiratory muscle strength in assessing and enhancing athletes' aerobic performance. These insights contribute to a deeper understanding of the interplay between respiratory function and exercise capacity, offering potential avenues for optimizing training regimens and perfor-mance outcomes in athletic contexts.

A method is proposed for describing the dynamics of systems of interacting particles in terms of an auxiliary field, which in the static mode is equivalent to given interatomic potentials, and in the dynamic mode is a classical relativistic composite field. It is established that for interatomic potentials, the Fourier transform of which is a rational algebraic function of the wave vector, the auxiliary field is a composition of elementary fields that satisfy the Klein-Gordon equation with complex masses. The interaction between particles carried by the auxiliary field is nonlocal both in space variables and in time. The temporal non-locality is due to the dynamic nature of the auxiliary field and can be described in terms of functional-differential equations of retarded type. Due to the finiteness mass of the auxiliary field, the delay in interactions between particles can be arbitrarily large. A qualitative analysis of the dynamics of few-body and many-body systems with retarded interactions has been carried out, and a non-statistical mechanisms for both the thermodynamic behavior of systems and synergistic effects has been established.

Human serum albumin (HSA) corona formation at polymer microparticles of a spheroidal shape was studied using dynamic light scattering and laser Doppler velocimetry (LDV). Physicochemical characteristics of the albumin comprising, the zeta potential and the isoelectric point were determined as a function of pH for various ionic strengths. Analogous characteristics of the polymer particles were carried out. The adsorption of albumin on the particles was monitored by electrophoretic mobility measurements (LDV). The stability of the HSA functionalized particle suspensions under various pHs and their electrokinetic properties were determined. The deposition kinetics of the particles on mica, silica and gold sensors were determined in situ by optical microscopy, AFM and by the quartz microbalance (QCM) under diffusion and flow conditions. The obtained results were interpreted in terms of the coarse-grained random sequential adsorption model that allowed to estimate the range of applicability of QCM for determining deposition kinetics of virus and bacteria at abiotic surfaces.

The esterification of propylene glycol methanol (PM) and acetic acid (AA) is an important reaction for the production of propylene glycol methyl ether acetate (PMA). Herein, we used macroporous ion exchange resin Amberlyst-35 as a catalyst to explore the effects of reaction conditions on the reaction rate and equilibrium yield of PMA. Under the optimized conditions of reaction temperature of 353 K, initial reactant PM/AA molar ratio of 1:3, and catalyst loading of 10 wt%, PMA equilibrium yield reached 78%, which is the highest equilibrium yield so far. The reaction equilibrium constants and activity coefficients were estimated to obtain reaction thermodynamic properties, indicating the exothermicity of the reaction. Furthermore, Pseudo-homogeneous (PH), Eley-Rideal (ER), and Langmuir-Hinshelwood-Hogen-Watson (LHHW) kinetic models were fitted based on experimental reaction kinetic data. The results demonstrate that the LHHW model is the most consistent with experimental data, indicating surface reaction controlled process and exhibiting an apparent activation energy of 62.0 kJ/mol. This work represents a valuable example of calculating the reaction thermodynamic and kinetics, which are particularly essential for promising industrial reactor design.

Reducing CO2 emissions is urgently needed to slow down the impacts of climate change. CO2 capture using an amine solution has been developed and implemented on pilot and commercial scales. However, amine scrubbing, in particular, produces a lot of degraded solvent as waste and is energy intensive. Solid sorbents have been called to overcome those drawbacks. In this work, waste biomass-derived carbon materials were developed and tested for CO2 capture and conversion. Advanced thermal chemical processes i.e. hydrothermal and pyrolysis were applied to produce materials from agri-food waste such as soybean and okara. It was found that the number of functional groups (-C=O and -OH) in activated carbon appears in the synthesized materials, implying the generation of surface oxygenated groups. Preliminary results showed that the synthesized activated carbons are obtained with good yields, and a relatively high surface area, which may be applied as CO2 adsorption materials to solve the CO2 emission problems.

The effects of rare earth Ce on the microstructure and properties of cast pure copper were investigated through thermodynamic calculations, XRD analysis, mechanical testing, metallographic microscopy, and scanning electron microscopy (SEM). The experimental results demonstrate that the reaction between rare earth Ce and oxygen as well as sulfur in copper exhibits a significantly negative Gibbs free energy value, indicating a strong thermodynamic driving force for deoxidation and desulfurization reactions. Ce is capable of removing trace amounts of O and S from copper. Moreover, the maximum solid solubility of Ce in Cu falls within the range of 0.009% to 0.01%. Furthermore, Ce can refine columnar grains while enlarging equiaxed grains in as-cast copper.Upon addition of rare earth Ce, the tensile strength increased by 8.45%, elongation increased by 12.1%, and microhardness rose from 73.5HV to 81.2HV-an increase of 10.5%. Overall, rare earth Ce has been found to enhance both the microstructure and mechanical properties of cast pure copper.

Molecular-scale density fluctuations at equilibrium produce cavities in a liquid and can be analyzed to shed light on the statistics of the number of molecules occupying observation volumes of increasing radius. An information theory approach led to the conclusion that these probabilities should follow a Gaussian distribution function. This prediction has been confirmed by computer simulations in different liquid models if the size of the observation volume is not large. The reversible work of cavity creation is exactly linked to the probability of finding zero molecules in a given observation volume. The Gaussian formula for the latter probability is scrutinized to arrive at the enthalpy and entropy changes associated with cavity creation. The reversible work of cavity creation has a purely entropic origin due to the solvent-excluded volume effect produced by the inaccessibility of a given region of the configurational space. The consequent structural reorganization of liquid molecules leads to exactly compensating enthalpy and entropy changes. These results are in line with those obtained in a direct statistical mechanical study by Lee.

Although composting has many advantages in the treatment of organic waste, there are still many problems and challenges associated with emissions, like NH3, VOCs, and H2S, as well as greenhouse gases such as CO2, CH4, and N2O. One promising approach to enhancing composting conditions is used of novel analytical methods bad on artificial intelligence. To predict and optimize the emissions (CO, CO2, H2S, NH3) during composting process kinetics thought mathematical models (MM) and machine learning (ML) models were utilized. Data about everyday emissions from laboratory composting with compost’s biochar with different incubation (50, 60, 70 °C) and biochar doses (0, 3, 6, 9, 12, 15% d.m.) were used for MM and ML models selections and training. MM has not been very effective in predicting emissions, (R2 0.1 - 0.9), while ML models such as acritical neural network (ANN, Bayesian Regularized Neural Network; R2 accuracy CO:0,71, CO2:0,81, NH3:0,95, H2S:0,72)) and decision tree (DT, RPART; R2 accuracy CO:0,693, CO2:0,80, NH3:0,93, H2S:0,65) have demonstrated satisfactory results. For the first time the ML models to predict CO and H2S during composting were demonstrated. Further research in a semi-scale and field study composting with biochar is needed to improve the accuracy of developments models.

Due to the accumulation of pesticides in the environment, the development of efficient strategies for their removal is of utmost importance. Activated carbons are currently seen as excellent candidates for adsorptive pesticide removal based on several beneficial properties, like a large surface area, developed porosity, and low price. However, a deep link between materials' properties and performance is still elusive. Here we focus on the kinetics of three organophosphate pesticides removal, aliphatic dimethoate and malathion and aromatic chlorpyrifos, using a series of carefully prepared activated carbon fibers. Used adsorbents have a wide range of specific surface areas, pore size distributions, and elemental content, allowing the establishment of the link between physicochemical properties and their performance as adsorbents. We use data analysis tools to link these properties and discuss their different roles in the removal of three structurally different yet extremely dangerous pesticides. The obtained results can guide the synthesis of novel adsorbents or rationally select adsorbents for specific target pollutants based on the physicochemical properties of adsorbents and the chemical structure of pollutants.

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

The numerical simulation of entropy generation at mixed natural free and forced convection flow in a square lid-driven cavity filled with an eletrically conducting binary fluids saturated porous media in the presence of a magnetic field is performed in this investigation. Both the top and bottom horizontal walls of the cavity are kept at constant and different temperatures while the left and right vertical walls are adiabatic and insulated. The magnetic field is applied in normal direction to the cavity. The Darcy model, including Brinkman term relative to viscous effects and Forchheimer term due to inertial forces, is used for the momentum equations, and the SIMPLER algorithm, based on the control volume finite-element method approach is used to solve the pressure –velocity coupling. The flow pattern and the heat transfer characteristics inside the cavity are presented in the form of isotherms, streamlines and isentropic lines and average Nusselt number trend. The entropy generation rate is determined for various values of Darcy number (10^-3 ≤ Da ≤ 1) and for a range of Hartmann number (0 ≤ Ha ≤ 10²). This study is limited to Pr = 7 which corresponds to water. It is observed that entropy generation is very affected by the variations of dimensionless control parameters considered.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

A sustainable low cost activated carbon substitute was produced based on pretreated lignocellulosic biomass, especially spruce sawdust. A harmful liquid waste, desalination brine was used for the treatment of a solid wood industry waste, spruce sawdust. This approach is in the circular economy theory and aims to the decarbonization of the economy. The pretreated sawdust was tested as an adsorbent appropriate for the removal of a commonly used pollutant, methylene blue, from industrial wastewater. The adsorption capacity of the pretreated material was found to increased four times comparing to the untreated one in the case that the Freundlich equation was fitted to the isotherms’ data. The treatment experimental conditions with desalination brine that gave maximum adsorption capacity correspond to 1.97 combined severity factor in logarithmic form value. The same adsorption capacity was found to increase five to six times comparing to the untreated spruce sawdust in the case that the Langmuir isotherm model was applied at the same data. Moreover, kinetic experiment was cried out as regards the methylene blue adsorption process. The desalination brine pretreated sawdust adsorption capacity increased 1.4 times comparing to the untreated one, in the case of the Lagergren kinetic equation fitting. Furthermore, the adsorption capacity of the same material was increased 1.6 times when the second order kinetic model was applied to the same data. Industrial scale applications can be based on the kinetic data findings as they have to do with a very shorter adsorption period comparing to the isotherm data.

Pore structure characterization and fractal analysis have great significance for understanding and evaluating tight limestone reservoirs. In this work, the pore structure of tight limestone is characterized combined with low-temperature nitrogen adsorption (LTNA) and low-field nuclear magnetic resonance (NMR), and the fractal dimension of tight limestone pore structure is discussed based on LTNA and NMR data. The results indicate that the pores of tight limestone have H3 and H4 types, the pore size distribution (PSD) of H3 type is a wave distribution ranging from 2 to 10 nm, and the PSD of H4 type is a unimodal distribution ranging from 2 to 10 nm. The transverse relaxation time (T2) spectrum of tight limestone shows single peak (DF), double peak (SF) and three peak (TF), and the T2 spectrums for micropores, mesopores and macropores range from 0.1 to 10 ms, from 10 to 100 ms, and greater than 100 ms, respectively. The LTNA fractal dimension of tight limestone (DL) ranges between 2.4446 and 2.7688, with an average of 2.5729, and the NMR fractal dimensions of micropores (DNMR1), mesopores (DNMR2) and macropores (DNMR3) are distributed between 0.3744 to 1.1293, 2.4263 to 2.9395 and 2.6582 to 2.9989, respectively. Moreover, there is no correlation between fractal dimension and permeability and porosity, a negative correlation between DL and average pore radius, a positive correlation between DL and specific surface area, and a positive correlation between DNMR2 and DNMR3 and micropore content, while DNMR2 and DNMR3 are negatively correlated with the content of mesopores and macropores.

Water is essential for all living things however its pain has become serious. Many industrial activities cause its pollution by the release of polluting byproduct. Waste water treatment is hence necessary. In this context, the waste water of the textile industry containing Red Acid 52 was treated by the solid waste of the washed natural phosphate byproduct. Natural phosphate was also studied. The solid materials were first characterized by chemical analysis, Fourier Transform Infrared spectroscopy (FTIR) and X-ray diffraction (XRD). The phosphate materials were after that, tested in the adsorption of the Red Acid 52. The experimental data indicated that the phosphate waste rock allowed the removal of Red Acid 52. Its maximum retention capacity attained 18.4 mg.g-1. Calcinations of materials inhibits the removal capacity found reduced by 60 to 70%. The adsorption kinetics of the Red Acid 52 on the material is well described by the pseudo second order model while the adsorption isotherms are identified by the Langmuir model. Hereafter, the thermodynamic study revealed that the adsorption process is spontaneous and exothermic. Keywords: Waste water, Phosphate co-product, Adsorption, Red Acid 52.

Zinc Oxide nanoparticles functionalized with APTES were obtained to evaluate their CH4 and CO2 adsorption and separation behavior. First, ZnO nanoparticles were obtained by a precipitation method and subsequently coated with (3-aminopropyl)-triethoxysilane (APTES). The nanoparticles sample was characterized by UV-Vis, FT-IR spectroscopy, TGA, XRD, TEM/EDX, XPS and N2 adsorption at 77 K. CH4 and CO2 adsorption experiments were carried out at 298 K in a range between 0-10 bar. It was observed that the amount of gas adsorbed on the surface of the nanostructure is very small in comparison with other materials traditionally used for this purpose but slightly higher than those obtained in naked nanoparticles evaluated in previous studies.

Weathering and erosion transport minerals and organics toward the sea or lake bottoms over geologic time. The finest solids are deposited in lower, less turbulent areas, such as lake bottoms and continental shelves. They sometimes stack up to thicknesses of kilometers, and begin compacting. These sediment sections are called shales, and as initially deposited in water, shales can have porosities up to 50-80{\%} water, As they are buried, many alteration products from oil to slate are produced due to overburden and temperature increasess, making them important to study. A preceeding paper \cite{1} showed that pressure solution is the primary mechanism for porosity reduction, with possible mechanical compaction at shallow depths. Without naming the mineral(s) involved, it postulated that the greater the product of the water and pore interfaces, the faster the reaction would proceed. This term is $ \varphi^{4m/3}(1-\varphi)^{4n/3}$ , where $\varphi$ is porosity and m and n are numbers close to unity. The large exponents, {\em 4/3}, recognize that the reaction occurs at the molecular scale at which the surfaces are rough. A second term, $\exp^{(-E/RT)}$ , indicates that the reaction is impeded by a quantum energy barrier, E, with diminished impeding power as increased available thermal energy, represented by the absolute temperature, T, becomes available at greater depths in the Earth. These two factors combine to allow porosity $\varphi$ to reduce with time, or equivalently for the fraction of solids, $(1-\varphi)$, to increase with time,$\left. \frac{\partial(ln(1-\varphi) ) }{\partial t } \right |_{\sigma} = (\varphi )^{4m/3}( 1-\varphi )^{4n/3}Ae^{-E/(RT)}$. { \em Here it is shown that this equation can cover quantitatively any actual deposition rates which may have been experienced by the six sections studied, the actual deposition rates being unknown for these cases. Hence a time-depth depositional history for any new shale section, known in detail, would allow determination of the parameters m, n, E and a lumped proportionality constant A. This was accomplished by showing that, for a wide range of depositional rates, r, the range of E for any of the studied sections is small compared to laboratory measurements of quartz solution\cite{2}, 24+-15kJ/mol. Results were obtained over this range of r's using the previously determined m and n, and porosity and temperature profiles. The presently existing porosity profiles necessarily incorporate any overpressure or underpressure conditions that may have existed in the past or currently, as the net difference between overburden and pore pressure is a primary driving force for pressure solution. $SiO_2$ usually comprises 20-50{\%} of shales. In conclusion, pressure solution of quartz can account for vertical compaction of shales quantitatively in the studied examples. Separately, a quasi-eqivalent method for discussing reduced porosities in Macron 2 versus Macron 1 as increased vertical stress, rather than additional horizontal stress, is illustrated. Experiments are suggested to clarify the pressure solution mechanism. The role of horizontal forces is discussed. From a global point of view, shale compaction by pressure solution is a quantified step in the cycling of continental rocks, beginning with rifting.

Turner syndrome (TS) is caused by a complete or partial absence of an X or Y chromosome, including chromosomal mosaicism, affecting 1 in 2,500 female live births. Sister chromatid exchange (SCE) is used as a sensitive indicator of spontaneous chromosome instability. Cells from mosaic patients constitute useful material for SCE evaluations as they grow under the influence of the same genetic background and endogenous and exogenous factors. We evaluated proliferation dynamics and SCE frequencies of 45,X and 46,XN cells of 17 mosaic TS patients. In two participants, 45,X cells exhibited a proliferative disadvantage in relation to 46,XN cells after 72h of cultivation. The analysis of mean PI showed significant differences between 45,X and 46,XN lineages; however there were no intraindividual differences. On the other hand, mean SCE frequencies showed no differences between the two lineages, but there were intraindividual differences in 5 patients. The absence of mean SCE frequency differences between 45,X and 46,XN lineages may indicate that both were equally unstable, as more than 70% of the 46,XN lineages had an anomalous karyotype. However, 46,XN had a higher mean PI, suggesting that the amount of cells with a karyotype distinct from 45,X may increase with time in mosaic TS women.

Cadmium(II) contamination in the environment is an emerging problem due to its acute toxicity and mobility, so it is very urgent to remove this species from industrial wastewater before it is discharged into the environment. Thus, a starch-based activated carbon (AC) with a specific surface area of 1600 m2g-1 is used as an adsorbent for the capturing of toxic cadmium(II) ions from synthetic solutions. The sorbent is characterized by BET, SEM, TEM, XRD, FT-IR, TGA, and zeta potential. The maximum uptake (284 mg g-1) of Cadmium(II) ion is obtained at pH 6. The thermodynamic parameters like ∆G, ∆H, ΔS are found to be -17.42 kJmol-1, 6.49 kJ mol-1, and 55.66 Jmol-1K-1 respectively, revealing that the adsorption mechanism is endothermic, spontaneous, and feasible. The experimental data follows the D-R and Langmuir models well. The mass transfer is controlled by pseudo 2nd order kinetics. Furthermore, the density functional theory simulations demonstrate that the activated carbon strongly interacted with the Cd(II) ion through its various active sites. The adsorption energy noted for all interactive sites is highly negative (-0.45 eV to -10.03 eV), which shows that the adsorption process is spontaneous and stable which is in agreement with the experimental thermodynamics analysis.

Kinetic parameters of SO2 adsorption on unburned carbons from lignite fly ash and activated carbons based on hard coal dust were determined. The model studies were performed using the linear and non-linear regression method for the following models: pseudo first and second-order, intraparticle diffusion, and chemisorption on a heterogeneous surface. The quality of the fitting of a given model to empirical data was assessed based on: R2, R, Δq, SSE, ARE, χ2, HYBRID, MPSD, EABS, and SNE. It was clearly shown that it is the linear regression that more accurately reflects the behaviour of the adsorption system, which is consistent with the first-order kinetic reaction – for activated carbons (SO2+Ar) or chemisorption on a heterogeneous surface – for unburned carbons (SO2+Ar and SO2+Ar+H2O(g)+O2) and activated carbons (SO2+Ar+H2O(g)+O2). Importantly, usually, each of the approaches (linear/non-linear) indicated a different mechanism of the studied phenomenon. A certain universality of the χ2 and HYBRID functions has been proved, the minimization of which repeatedly led to the lowest SNE values for the indicated models. Fitting data by any of the non-linear equations based on the R or R2 functions only, cannot be treated as evidence/prerequisite of the existence of a given adsorption mechanism.

Three kinds of inorganic alkali are introduced into tetraethylenepentamine (TPEA) and polyethyleneimine (PEI) modified MCM-41 as the CO2 adsorbents. FT-IR and TGA are used to characterize the surface groups and the thermal stability of adsorbents. Chemical titration method is used to measure the alkali amounts of adsorbents. Thermo-gravimetric analysis with 10%CO2/N2 as the simulated flue gas is used to test the CO2 adsorption performance of adsorbents. The results show that all three kinds of inorganic alkali containing adsorbents exhibit promoted CO2 adsorption capability than traditional TPEA and PEI modified samples. Ca(OH)2 and PEI modified samples exhibit the highest adsorption capacity and stable regeneration property. The introduction of inorganic alkali changes the chemical adsorption mechanism between CO2 and increases the effective alkali amounts due to its hydroxyl groups. The CO2 adsorption capacities have a linear dependence relation with the alkali amounts of adsorbents, indicating that alkali amount is a critical factor for novel adsorbents exploring.

The alcoholic fermentation process with agitation/static, followed by the acetic fermentation submerged in banana was evaluated. Kinetics parameters of alcoholic fermentation for the maximum ethanol/glycerol metabolites in agitated process was 29 and 27 h, and in static 47 and 45 h, respectively. For acetic fermentation, the kinetics parameters were medium time of 39.9 h, acetic acid yield of 53.1% and acetic acid productivity of 0.216 g/Lh. Wines from agitated/static process presented 5.73 and 6.81% (v/v) of alcohol content, respectively. Wine obtained by the static process presented higher concentrations of volatile compounds. The vinegar showed 49.2 g/L of acetic acid and the esters concentrations were higher than in wine. The wine and vinegar minerals were consistent with amount observed in the pulp, with an increase in sulphur concentration after alcoholic fermentation and decrease after acetic fermentation. Products showed chemical and composition of sensory and nutritional interest.

Spent coffee grounds (SCG) have great potential as a useful, value-added biological material. In this context, activated carbon (AC) was prepared from SCG by an activation process using H3PO4 at 600°C in air and used as an adsorbent for the azo dye AO7, a model molecule for dye colorants found in textile industry effluents. X-ray diffraction, SEM and BET revealed that the AC was predominantly amorphous, consisting of a powder of 20-100 µm particles with mesopores averaging 5.5 nm in pore size. Adsorption kinetics followed a pseudo-second-order law, while the Langmuir model best fitted experimental isotherm data (maximum capacity of 119.5 mg AO7 per AC g). Thermodynamic parameters revealed that adsorption was endothermic and spontaneous. All the characterizations indicated that adsorption occurred by physisorption via mainly - interactions. The best experimental removal efficiency optimized by means of a Box-Behnken design and response surface methodology was 98% for an initial AO7 concentration of 20 mg.L-1 at pH 7.5 with a dose of 0.285 g.L-1 of AC and a contact time of 40 min. These results clearly show that activated carbon prepared from SCG can be a useful material for efficiently removing organic matter from aqueous solutions.

This study aimed to evaluate the impact of Candida albicans on subgingival biofilm formation on dental implant surfaces. Scanning electron microscopy (SEM) and confocal laser scanning microscopy (CLSM) were used to compare biofilm structure and microbial biomass in the presence and absence of the fungus after periods of 24, 48, and 72 h. Quantitative polymerase chain reaction (qPCR) was used to quantify the number of viable and total micro-organisms for each of the biofilm-forming strains. A general linear model was applied to compare CLSM and qPCR results between control and test conditions. The biofilm developed with C. albicans at 72 h had a higher bacterial biomass, with a significantly higher cell viability (p &lt; 0.05). After both 48 and 72 h of incubation, in the presence of C. albicans, there was a significant increase in counts of Fusobacterium nucleatum and Porphyromonas gingivalis and in the cell viability of Streptococcus oralis, Aggregatibacter actinomycetemcomitans, F. nucleatum, and P. gingivalis. Using a dynamic in vitro multispecies biofilm model, C. albicans exacerbated the development of the biofilm grown on dental implant surfaces, significantly increasing the number and cell viability of periodontal bacteria.

Re-shaping of thermodynamics with the graph theory and Ramsey theory is suggested. Maps built of thermodynamic states are addressed. Thermodynamic states may be attainable and non-attainable by the thermodynamic process in the system of constant mass. We address the following question how large should be a graph describing connections between discrete thermodynamic states to guarantee the appearance of thermodynamic cycles? The Ramsey theory supplies the answer to this question. Direct graphs emerging from the chains of irreversible thermodynamic processes are considered. In any complete directed graph, representing the thermodynamic states of the system the Hamiltonian path is found. Transitive thermodynamic tournaments are addressed. The entire transitive thermodynamic tournament built of irreversible processes does not contain a cycle of length 3, or in other words, the transitive thermodynamic tournament is acyclic and contains no directed thermodynamic cycles.

This work aimed to develop an anionic cellulose nanofiber (CNF) bio-adsorbent from palm date tree waste and to investigate its removal efficiency against cationic methylene blue dye from contaminated water. Palm date pulp was first prepared from palm date leaves through acid hydrolysis using H2SO4, followed by hydrolysis in a basic medium using KOH, in which the process completely removed the components of hemicellulose, lignin, and silica. To obtain anionic CNF, the resulting pulp was further treated with H2SO4, followed by centrifugation. Biogel formation of the CNF suspension was promoted by sonication, where its removal efficiency of methylene blue dye was studied as a function of dye concentration, temperature, contact time, and pH value. Two equilibrium models, the Langmuir and Freundlich models were employed, and the Langmuir model was found to be consistent with the experimental data. The highest removal efficiency was obtained at 60oC and was 5mg/gm. Furthermore, several kinetic models were used to gain insight into the adsorption mechanism. The pseudo-second-order model provided an accurate description of the adsorption process, while the Elovich equation suggested a chemical reaction between methylene blue dye and CNF. The study’s findings were in agreement with the pseudo-second-order model, indicating general chemical reactions. The study indicates that CNF adsorbents derived from renewable natural waste sources such as palm date leaves can be effective in removing cationic contaminants such as methylene blue dye.

Despite the successful introduction of oral cholera vaccines, Zambia continues to experience multiple, sporadic, and protracted cholera outbreaks in various parts of the country. While vaccines have been useful in staying the cholera outbreaks, the ideal window for re-vaccinating individual’s resident in cholera hotspot areas remains unclear. Using a prospective cohort study design, 225 individuals were enrolled, re-vaccinated with two doses of Shanchol™ regardless of previous vaccination and followed-up for 90 days. Bloods collected at baseline before re-vaccination, at day 14 prior to second dosing and subsequently on days 28, 60, and 90. Vibriocidal assay was performed on samples collected at all five time points. Our results showed that anti-LPS and vibriocidal antibody titers increased at day 14 after re-vaccination and decreased gradually at 28, 60 and 90 across all the groups. Seroconversion rates were generally comparable in all treatment arms. We therefore conclude that vibriocidal antibody titers generated in response to re-vaccination still wane quickly irrespective of previous vaccination status. However, despite the observed decline, the levels of vibriocidal antibodies remained elevated over baseline values across all groups, an important aspect for Zambia where there is no empirical evidence as to the ideal time for re-vaccination.

We consider the thermodynamic and stability problem of Kerr black holes arising from the nonextensive/nonadditive nature of the Bekenstein-Hawking entropy formula. Nonadditive thermodynamics is often criticized by asserting that the zeroth law cannot be compatible with nonadditive composition rules, so in this work we follow the so-called formal logarithm method to derive an additive entropy function for Kerr black holes satisfying also the zeroth law's requirement. Starting from the most general, equilibrium compatible, nonadditive entropy composition rule of Abe, we consider the simplest, non-parametric approach that is generated by the explicit nonadditive form of the Bekenstein-Hawking formula. This analysis extends our previous results on the Schwarzschild case and shows that the zeroth law compatible temperature function in the model is independent of the mass-energy parameter of the black hole. By applying the Poincaré turning point method we also study the thermodynamic stability problem in the system.

This study aimed to develop a laboratory-scale direct air capture unit for evaluating and comparing amine-based adsorbents under temperature vacuum swing adsorption conditions. The experimental campaign conducted with the direct air capture unit allowed for the determination of equilibrium loading, CO2 uptake capacity, and other main performance parameters of the investigated adsorbent Lewatit VP OC 1065®. The investigations also helped to understand the co-adsorption of both CO2 and H2O on the tested material, which is crucial for improving temperature vacuum swing adsorption processes. This was achieved by obtaining pure component isotherms for CO2 and H2O as well as three different co-adsorption isotherm models from literature. It was found that the weighted average dual-site Toth model emerged as the most accurate and reliable model for simulating this co-adsorption behavior. Its predictions closely align with experimental data, particularly in capturing the adsorption equilibrium at various temperatures. It was also observed that this lab-scale unit offers advantages over thermogravimetric analysis when conducting adsorption experiments on the chosen amine. The final aim of this study is to provide a pathway to develop devices for testing and developing efficient and cost-effective adsorbents for direct air capture.

We report on the role of synergistic polarization of Ba0.9Sr0.1TiO3 (BST) nanoparticles in sulfur cathodes to enhance the redox kinetics of polysulfides for high-capacity Li-S batteries. Ferroelectric nanoparticles are known to significantly improve the electrochemical performance of Li-S batteries due to their inherent self-polarization and high adsorption capacity towards polysulfides. X-ray diffraction spectra confirmed the tetragonal symmetry (c/a=1.0073), while Raman spectroscopic analysis validated the presence of tetragonal orientation Raman modes in BST-modified composites. Scanning electron microscope (SEM) images showed a homogeneous distribution of BST in the sulfur cathode system, with grain sizes ranging from 1 to 1.5 μm. Notably, the BST-coupled S50BST30CB10PVDF10 composite cathode achieved a capacity of approximately 820 mAh/g at 100 mA/g, maintaining stability over 100 cycles, demonstrating improved electrochemical performance. Two distinct plateaus between 2.3 V to 2.0 V and 2.0 V to 1.5 V further underscore the superior performance of BST ferroelectric nanoparticles in enhancing the redox kinetics of Li-S batteries. By leveraging the favourable affinity of polar substances towards polysulfides, we aimed to create a more stable reactive environment within the cathodic site, effectively trapping polysulfide intermediates through the synergistic polarization of BST nanoparticles. The synergistic polarization induced by the asymmetric crystal structure of ferroelectrics is anticipated to generate internal electric fields, enhancing chemisorption with heteropolar reactive. The observed high cyclic stability further validates the efficacy of these composite cathodes in mitigating the polysulfide shuttle effect, offering promising prospects for advancing Li-S battery technology.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

The results of the investigation showed that second-order kinetics govern the adsorption process, and the corresponding rate constants were found. To evaluate the parameters related to the adsorption process, the adsorption equilibrium was examined using a variety of mathematical models, such as the Langmuir, Freundlich, Temkin, and Dubinin-Radushkevich isotherm models. The Langmuir isotherm was found to be the best appropriate among all models for describing the adsorption of Cu2+ and Ni2+ ions using bio-nanocomposite beads. The positive values of ΔH° indicate that the adsorption is physical and endothermic, in agreement with experimental results. The negative value of ∆G° shows that the adsorption process is spontaneous. Positive ΔS° values indicate increased randomness at the solid/liquid interface, during adsorption of Cu2+ and Ni2+ cations onto the engineered bio-nanocomposite. The maximum adsorbed amounts of metal ions by the bio-nanocomposite used were 370.37 mg/g for Ni2+ and 454.54 mg/g for Cu2+ from single system. For the binary system, according to the Langmuir isotherm, the maximum adsorbed amounts of Ni2+ and Cu2+ were 357.14 mg/g and 370,37 mg/g, respectively. There is proof that Alginate-Moroccan clay bio-nanocomposites can serve as a different, less expensive source of sorbents for the removal of metal ions from single and binary systems.

The massive amount of human biological, imaging and clinical data produced by multiple and diverse sources, necessitates integrative modeling approaches able to summarize all this information into answers to specific clinical questions. In this paper, we present a hypermodeling scheme able to combine models of diverse cancer aspects regardless of their underlying method or scale. Describing tissue-scale cancer cell proliferation, biomechanical tumor growth, nutrient transport, genomic-scale aberrant cancer cell metabolism, and cell signaling pathways that regulate the cellular response to therapy, the hypermodel integrates mutation, miRNA expression, imaging, and clinical data. The constituting hypomodels as well as their orchestration and links are described. Two specific cancer types, Wilms tumor (nephroblastoma) and non-small cell lung cancer, are addressed as proof of concept study cases. Personalized simulations over the actual anatomy of a patient have been carried out. The hypermodel has also applied to predict tumor control after radiotherapy and the relationship between tumor proliferative activity and response to neoadjuvant chemotherapy. Our innovative hypermodel holds promise as a digital twin based clinical decision support system and the core of future in silico trial platforms, although additional retrospective adaptation and validation is necessary.

The growing threat of antibiotic pollution in water systems demands innovative and sustainable remediation strategies. Nanocellulose-based magnetic metal-organic frameworks (MOFs) represent a cutting-edge solution for the adsorption and removal of antibiotics, leveraging their high porosity, magnetic properties, and environmentally friendly nature. This paper provides an in-depth review of recent advancements in nanocellulose-based MOFs, focusing on their synthesis, adsorption mechanisms, and applications in environmental remediation between 2020 and 2024. By summarizing key studies, we highlight their performance in targeting widely used antibiotics such as tetracyclines and fluoroquinolones. The integration of nanocellulose with MOFs not only enhances adsorption capacity but also offers easy recovery, recyclability, and environmental compatibility. This review explores their adsorption mechanisms, practical applications, and future research directions, contributing to the advancement of scalable and sustainable water treatment technologies.

From the formalism of the thermodynamics of irreversible processes and the theory of complex systems, characterization of longevity and aging and its relationship with the emergence and evolution of cancer was carried out. It was found that: 1. The rate of entropy production can be used as an index of robustness, plasticity, the aggressiveness of cancer, and as a measure of biological age; 2. The aging process, as well as the evolution of cancer, goes through what we have called “biological phase transition”; 3. The process of metastasis, which occurs through epithelial-mesenchymal transition (EMT), appears as a phase transition far from thermodynamic equilibrium and exhibits Shilnikov chaos-like dynamic behavior. This dynamic guarantees the robustness of the process and, in turn, its unpredictability; 4. It was shown that as the ferroptosis process is strengthened, the complexity of the dynamics associated with the emergence and evolution of cancer decreases. The theoretical framework developed contributes to a better understanding of the biophysical-chemical phenomena of longevity and aging and their relationship with cancer.

PFAS are a variety of ecologically persistent compounds of anthropogenic origin loosely included in many industrial products, in which the carbon chain can be fully (perfluoroalkyl substances) or partially (polyfluoroalkyl substances) fluorinated. Their ubiquitous presence in many environmental compartments over the years, and highly long-lasting nature, arose concern because of the possible adverse effects of PFAS on ecosystem and human health. Between the remediation technologies, adsorption has been demonstrated to be a maneageble and cost-effective method for the removal of PFAS in aqueous media. This study tested two novel and eco-friendly adsorbents (pinewood and date seeds biochar) on 6 different PFAS (PFOS, GenX, PFHxA, PFOA, PFDA, PFTeDA). Batch sorption tests (24 hours) were carried out to evaluate the removal efficiency of each PFAS substance in relation to the two biochars. All samples of liquid phase were analysed by a developed and then well-established method: i) pre-treatment (centrifugation and filtration); ii) determination by high-performance liquid chromatography coupled with mass spectrometry (HPLC-MS/MS). Results evidenced a comparable adsorption capacity of both materials, but greater for the long-chain PFAS. Such findings may lead to a promising path for the use of waste origin materials in the PFAS remediation field.

The temperature effect plays an important role for an accurate determination of the polar free energy, polar thermodynamic parameters, and enthalpic and entropic Lewis’s acid base properties of oxides, polymers and composites polymers/oxides. The adsorption of polymers on other solid surfaces is crucial in many industrial applications, coatings, paints, catalysis, colloids and adhesion processes. (1) Background: Inverse gas chromatography at infinite was used for the physico-chemical characterization of solid substrates by determining the thermodynamic parameters of adsorption of model organic solvents on solid surfaces such as polymers, metallic oxides, carbon fibers, pharmaceutical or 3D/4D printing substrates. (2) Methods: A new method based on the London dispersion equation was applied with a new parameter associating the deformation po-larizability and the harmonic mean of the ionization energies of solvent. More accurate values of the dispersive and polar interaction energies of the various organic solvents adsorbed on PMMA in bulk phase and PMMA/silica at different recovery fractions were obtained as well as the Lewis acid-base parameters and the transition temperatures of the different composites. (3) Results: This new methodology gave very interesting results on the behavior of PMMA adsorbed on silica. An important effect of the temperature and the recovery fraction on the various physicochemical and thermodynamic properties was highlighted. The variations of all interaction parameters showed the presence of three transition temperatures for the different PMMA adsorbed on silica with the various coverage rates with a shift of these temperatures for a recovery fraction of 31% (4) Con-clusions: An important variation of the polar enthalpy and entropy of adsorption, the Lewis ac-id-base parameters and the intermolecular separation distance as a function of the temperature and the recovery fraction of PMMA on silica.

We discuss the consequences of the unique symmetry of the de Sitter spacetime. This symmetry leads to the specific thermodynamic properties of the de Sitter vacuum, which produces the thermal bath for matter. The de Sitter spacetime is invariant under the modified translations, ${\bf r}\rightarrow {\bf r} -e^{Ht}{\bf a}$, where $H$ is the Hubble parameter. For $H\rightarrow 0$, this symmetry corresponds to the conventional invariance of Minkowski spacetime under translations ${\bf r}\rightarrow {\bf r} -{\bf a}$. Due to this symmetry, all the comoving observers at any point of the de Sitter space perceive the de Sitter environment as the thermal bath with temperature $T=H/\pi$, which is twice larger than the Gibbons-Hawking temperature of the cosmological horizon. This temperature does not violate the de Sitter symmetry, and thus does not require the preferred reference frame, as distinct from thermal state of matter, which violates the de Sitter symmetry. This leads to the heat exchange between gravity and matter, and to instability of de Sitter state towards the creation of matter, its further heating, and finally to the decay of the de Sitter state. The temperature $T=H/\pi$ determines different processes in the de Sitter environment, which are not possible in the Minkowski vacuum, such as the process of ionization of an atom in the de Sitter environment. This temperature also determines the local entropy of the de Sitter vacuum state, and this allows us to calculate the total entropy inside the cosmological horizon. The result reproduces the Gibbons-Hawking area law, which is related to the cosmological horizon, $S_{\rm hor}=4\pi KA$, where $K=1/16\pi G$. This supports the holographic properties of the cosmological event horizon. We extend the consideration of the local thermodynamics of the de Sitter state using the $f({\cal R})$ gravity. In this thermodynamics, the Ricci scalar curvature ${\cal R}$ and the effective gravitational coupling, $K$, are thermodynamically conjugate variables. The holographic connection between the bulk entropy of the Hubble volume, and the surface entropy of the cosmological horizon remains the same, but with the gravitational coupling $K=df/d{\cal R}$. Such connection takes place only in the $3+1$ spacetime, where there is the special symmetry due to which the variables $K$ and ${\cal R}$ have the same dimensionality. We also consider the lessons from the de Sitter symmetry for the thermodynamics of black and white holes.

Current physiology attributes the mechanism of membrane potential generation to transmembrane ion transport, but ion adsorption could just as well play this fundamental role. The evidence shows that the ion adsorption mechanism accurately reproduces the experimentally measured membrane potential. The Goldman-Hodgkin-Katz equation (GHK eq.) and the Nernst equation (Nernst eq.) are the typical mathematical formulas representing the membrane potential in current physiology. However, the authors were able to show that the potential formulas by ion adsorption mechanism give identical results to GHK eq. and Nernst. eq. Our experimental and theoretical analyses suggest that there is a special relationship between the membrane potential and the membrane surface charge density, and this unique equation inevitably leads to the establishment of a GHK eq and/or a Nernst eq. The authors found that the unique equation is the foundation of thermodynamics “Boltzmann distribution”. Thus, the GHK eq. and the Nernst eq. are simply the natural consequence of thermodynamics from the view of the ion adsorption mechanism.

The emission of toxic gases from industrial production have intensified issues related to atmospheric pollution and human health. Consequently, the effective real-time monitoring and removal of these harmful industrial gases have emerged as significant challenges. In this work, the density functional theory (DFT) method was utilized to examine the adsorption behaviors and electrical characteristics of Ni-decorated InSe (Ni-InSe) monolayer when interacting with twelve gases (CO, NO, NO2, NH3, SO2, H2S, H2O, CO2, CH4, H2, O2 and N2). A comparative assessment of adsorption strength and sensing properties was performed through analyses of electronic structure, work function and recovery time. The results show that Ni doping enhances the electrical conductivity of the InSe monolayer and improves the adsorption capabilities for six toxic gases (CO, NO, NO2, NH3, SO2, H2S). Furthermore, the adsorption of these gases on the Ni-InSe surface is characterized as chemisorption, as indicated by the analysis of adsorption energy, density of states, and charge density difference. Additionally, the adsorption of CO, NO, NO2, and SO2 results in significant alterations to the bandgap of Ni-InSe, with changes of 18.65%, 11.37%, 10.62%, and –31.77%, respectively, underscoring its exceptional sensitivity. Moreover, the Ni-InSe monolayer exhibit moderate recovery times of 3.24 s and 22.72 s at 298 K for the SO2 and H2S, respectively. Consequently, the Ni-InSe is regarded as a promising gas sensor for detecting SO2 and H2S at room temperature. This research establishes a foundation for developing Ni-InSe based gas sensor in detecting and mitigating harmful gas emissions.

In this paper, we study quantum gravity effect on the symmergent black hole which is derived from quadratic-curvature gravity. To do so, we use the Klein-Gordon equation which is modified by generalized uncertainty principle (GUP). After solving the field equations, we examine the symmergent black hole's tunneling and Hawking temperature. We explore the graphs of the temperature through the outer horizon to check the GUP influenced conditions of symmergent black hole stability. We also explain how symmergent black holes behave physically when influenced by quantum gravity. The impacts of thermal fluctuations on the thermodynamics of a symmergent black holes spacetime are examined. We first evaluate the model under consideration's thermodynamic properties, such as its Hawking temperature, angular velocity, entropy, and electric potential. We evaluate the logarithmic correction terms for entropy around the equilibrium state in order to examine the impacts of thermal fluctuations. In the presence of these correction terms, we also examine the viability of the first law of thermodynamics. Finally, we evaluate the system's stability using the Hessian matrix and heat capacity. It is determined that a stable model is generated by logarithmic corrections arising from thermal fluctuations.

The prevailing interpretations of physics are based on deeply entrenched assumptions, rooted in classical mechanics. Logical implications include: the denial of entropy as a fundamental physical property, and the inability to explain irreversible change, random quantum measurements, or nonlocality without untestable and implausible metaphysical implications. We propose a conceptual model that is based on empirically justifiable assumptions and consistent with observations. The WYSIWYG Conceptual Model (WCM) assumes no hidden properties: “What You can See Is What You Get.” The WCM contextually defines a system’s state with respect to its actual ambient background, and it extends existing models of physical reality by defining entropy and exergy as objective contextual properties of state. The WCM establishes the irreversible dissipation of exergy and the Second law of thermodynamics as a fundamental law of physics, it recognizes physical randomness, and it provides a physical explanation for nonlocality, consistent with Special Relativity, without hidden variables, superdeterminism, or “spooky action.”

Trailing the modern ideas of sociophysics, a minimalistic thermodynamic model of society is proposed, which consists of three social ingredients: people, economy, and entropy. Employing the universal van der Waals equation of state, many important relationships are discovered, including laws of econophysics. A paramount finding is that the Second Law of thermodynamics governs irreversible social evolution, revealing the power of social liberty and economic freedom.

Comprehending the replication kinetics of SARS-CoV-2 variants helps explain why certain var-iants spread more easily and are more contagious, and pose significant health menaces to the global populations. The replication kinetics of Malaysian isolates of the Alpha, Beta, Delta, and Omicron variants were studied in the Vero E6 cell line. Their replication kinetics were deter-mined using the plaque assay, quantitative real-time PCR (qRT-PCR), and viral growth curve. The Beta variant exhibited the highest replication rate at 24 hours post-infection (h.p.i), as evi-denced by the highest viral titers and lowest viral RNA multiplication threshold. The plaque phenotypes also varied among the variants, in which the Beta and Omicron variants formed the largest and smallest plaques, respectively. All studied variants showed strong cytopathic effects after 48 h.p.i. The whole-genome sequencing highlighted cell-culture adaptation, where the Beta, Delta and Omicron variants acquired mutations at the multibasic cleavage site after three cycles of passaging. The findings suggest a strong link between the replication rates and their respec-tive transmissibility and pathogenicity. This is essential in predicting the impacts of the upcom-ing variants on the local and global populations and is useful in designing preventive measures to curb the virus outbreaks.

A photon inside a gravitational eld dened by the accelerates g is found to have a gravitational mass given by m_g = (ћ=2c³)g, where ћ is the reduced Planck's constant, and c is the speed of light in vacuum. This force is equivalent to the curvature force introduced by Einstein's general relativity. These photons behave like the radiation emitted by a black hole. A black hole emitting such a radiation develops an entropy that is found to increase linearly with black hole mass, and inversely with the photon mass. Based on this, the entropy of a solar black hole emitting photons of mass ~10^-33eV amounts to ~10⁷⁷ kB. The created photons could be seen as resulting from quantum fluctuation during an uncertainty time given by Δt = c/g. The gravitational force on the photon is that of an entropic nature, and varies inversely with the square of the entropy. The power of the massive photon radiation is found to be analogous to Larmor power of an accelerating charge.

This article argues that there is a consistent description of gravitationally collapsed bodies, including neutron stars above the Tolman-Oppenheimer-Volkoff mass and also supermassive galactic centres, according to which collapse stops before the object reaches its gravitational radius, the density reaching a maximum close to the surface and then decreasing towards the centre. Models for such shell-like objects have been constructed using classic formulations found in the 1939 articles of Oppenheimer-Volkoff and Oppenheimer-Snyder. It was possible to modify the conclusions of the first article by changing the authors’ boundary conditions at r = 0. In the second case we find that the authors’ solution of the field equations needs no changes, but that the choice of their article’s title led many of their successors to believe that it supports the black-hole hypothesis. However, it is easily demonstrated that their final density distribution accords with the shell models found in our articles. Because black holes, according to many formulations, "have no hair", their thermodynamics is rather simple. The kind of collapsar which our models describe are more like main-sequence stars; they have spatiotemporal distributions of pressure, density and temperature, that is they have hair. In this article we shall concentrate on the dynamics of the Oppenheimer-Snyder collapsar; both pressure and temperature are everywhere zero, so there can be no thermodynamics. Only in the time independent case of Oppenheimer-Volkoff type models is it currently feasible to consider some thermodynamic implications; here some valuable new insights are obtained through the incorporation of the Oppenheimer-Snyder dynamics.

The grain-to-grain stress vertically in sediments is given by the overburden less the pore fluid pressure, σ, divided by the fraction of the horizontal area which is the supporting matrix , (1 − φ), where φ is the porosity. It is proposed that the fractional reduction of this ratio, Λ, with time is given by the product of φ 4m/3 , (1 − φ) 4n/3 , and one or more Arrhenius functions A exp(−E/RT ) with m and n close to 1. This proposal is tested for shale sections in six wells from around the world for which porosity-depth data are available. Good agreement is obtained above 30-40 C and porosities less than 0.5. Single activation energies for each well are obtained in the range 15-33 kJ/mole, close to pressure solution of quartz, 24 kJ/mol. Values of m and n are in the range 1 to 0.8, indicating nearly fractal pore-matrix spaces and water-wet interfaces. Results are independent of over- or under-pressure of pore water. This model explains shale compaction quantitatively. Given porosity-depth data and accurate activation energy, E, one can infer paleo-geothermal-gradient and from that organic maturity, thus avoiding unnecessary drilling.

Under typical marine conditions of about 80 % relative humidity, evaporation of water from the ocean is an irreversible process accompanied by entropy production. In this article, equations are derived for the latent heat of irreversible evaporation and the related non-equilibrium entropy balance at the sea surface. To achieve this, linear irreversible thermodynamics is considered in a conceptual ocean evaporation model. The equilibrium thermodynamic standard TEOS-10, the International Thermodynamic Equation of Seawater – 2010, is applied to irreversible evaporation under the assumption of local thermodynamic equilibrium. The relevance of local-equilibrium conditions for irreversible thermodynamics is briefly explained. New equations are derived for the mass flux of evaporation and for the associated non-equilibrium enthalpies and entropies. The estimated entropy production rate of ocean evaporation amounts to 0.004 W m^(-2) K^(-1) as compared to the average terrestrial global entropy production of about 1 W m^(-2) K^(-1).

The holographic principle states that the information about the volume of space is stored on its boundary. Assuming this holds, we can explain the aspects of gravity. The spacetime needs to be extended to 5D to explain gravity in this context. This naturally explains the four classical tests of gravity namely the gravitational redshift, the perihelion precession, the bending of light, and the gravitational time delay. We also show a novel way in which the universe expands in an accelerated manner at late times without the need for any form of dark energy.

We survey the main results emerging in the rapidly developing field that considers the geometry of thermodynamics and statistical mechanics. Our ideas of stability depend on variational principles – Maximum Entropy together with Least Action (and the isomorphic Least Exertion) – and this stability (invariance in time) indicates the centrality of the geometries of the systems. We explore a variety of examples of the application of thermodynamics in both macro- and micro-systems, and propose that irreversibility is an intrinsic and fundamental property of the physical realm (instead of being merely emergent). Using the concept of complex time, we examine the underlying mathematical unity of quantum mechanics, statistical mechanics, and geometrical thermodynamics. We show how the Planck and Boltzmann constants provide the fundamental quantum units for the phenomenological characteristics of the two Noether-conserved quantities controlling overall thermodynamic behaviour: respectively, energy and entropy production. We discuss the far-reaching isomorphisms (between all of complex time, temperature and the system symmetry) that always exist for Maximum Entropy systems, even as they exhibit either irreversible (dissipative, yet still dynamically stable) or reversible (including stable and static geometries) behaviours.

Classical physics meets the obstacle of describing a point particle because from everyday experience we know that objects occupy a certain volume. We overcome this obstacle by using the equivalence principle for electric energy and describe a curved spacetime of fluid nature. From thereon by using the notion of a point volume the rest of the thermodynamic quantities appear.

We apply the stochastic thermodynamics formalism to describe the dynamics of systems of complex Langevin and Fokker-Planck equations. We provide in particular a simple and general recipe to calculate thermodynamical currents, dissipated and propagating heat for networks of nonlinear oscillators. By using the Hodge decomposition of thermodynamical forces and fluxes, we derive a formula for entropy production that generalises the notion of non-potential forces and makes transparent the breaking of detailed balance and of time reversal symmetry for states arbitrarily far from equilibrium. Our formalism is then applied to describe the off-equilibrium thermodynamics of a few examples, notably a continuum ferromagnet, a network of classical spin-oscillators and the Frenkel-Kontorova model of nano friction.

Silicon (Si) is the major material of semiconductor element. For semiconductor element producing, Si need to refined into high-purity silicon crystals, which has the approximate characteristics of intrinsic semiconductor, then doping 13th group or 15th group trace element. Producing the high-purity silicon crystals with well-lattice structure need a lot of energy and highly cost. Besides, the high-purity silicon is very hard and fragile which limits the scope of application. For this reason, this study added low-grade non-complete lattice silicon in the elastic polymer, and then doped with high concentrations of fine carbon powder. This material can be conductive by physisorption;therefore, it can be used to making semiconductors. Using this material to produce electronic components can significantly reduce the cost of purification and crystallization, saving energy at the same time. Moreover, because this elastic polymer materials containing silicon, which has soft, warm, and durable physical properties. With those properties, the design of the device could be more flex, full scalability and close to the skin.

Here we investigate how the local properties of particles in a thermal bath may influence the thermodynamics of the bath, and consequently alter the statistical mechanics of subsystems that comprise the bath. We are guided by the theory of small-system thermodynamics, which is based on two primary postulates: that small systems can be treated self-consistently by coupling them to an ensemble of similarly small systems, and that a large ensemble of small systems forms its own thermodynamic bath. We adapt this “nanothermodynamics” to investigate how a large system may subdivide into an ensemble of smaller subsystems, causing internal heterogeneity across multiple size scales. For the semi-classical ideal gas, maximum entropy favors subdividing a large system of “atoms” into an ensemble of “regions” of variable size. The mechanism of region formation could come from quantum exchange symmetry that makes atoms in each region indistinguishable, while decoherence between regions allows atoms in separate regions to be distinguishable by their distinct locations. Combining regions reduces the total entropy, as expected when distinguishable particles become indistinguishable, and as required by a theorem in quantum mechanics for sub-additive entropy. Combining large volumes of small regions gives the usual entropy of mixing for a semi-classical ideal gas, resolving Gibbs paradox without invoking quantum symmetry for atoms that may be meters apart. Other models presented here are based on Ising-like spins, which are solved analytically in one dimension. Focusing on the bonds between the Ising-like spins we find similarity in the equilibrium properties of a two-state model in the nanocanonical ensemble and a three-state model in the canonical ensemble. Thus, emergent phenomena may alter the thermal behavior of microscopic models, and the correct ensemble is necessary for fully-accurate predictions. Another result using Ising-like spins involves simulations that include a nonlinear correction to Boltzmann’s factor, which mimics the statistics of indistinguishable states by imitating the dynamics of spin exchange on intermediate lengths. These simulations exhibit 1/f-like noise at low frequencies (f), and white noise at higher f, similar to equilibrium thermal fluctuations found in many materials.

The current evolutionary theories have remained incomplete, controversial, and stagnant for multiple decades. To solve this issue, we create the concept of carbon-based entities (CBEs) which include methane, amino acids, proteins, organisms, and other entities containing carbon atoms. We deduce from thermodynamics the driving force, the progressive mechanisms, and the major steps of evolution of CBEs, and hence establish a comprehensive evolutionary theory termed the CBE evolutionary theory (CBEET). The CBEET demonstrates that evolution is driven hierarchy-wise by thermodynamics and favors fitness and diversity. It provides novel explanations for origin of life (abiogenesis), macroevolution, natural selection, sympatric speciation, evolution tempos, animal group evolution, and human society development in a comprehensive and comprehensible way. It elucidates that collaboration, altruism, obeying rules with properly increased freedom are important throughout evolution of CBEs. It refutes thoroughly the wrong notion that negative entropy (negentropy) leads to biological order which is distinct from thermodynamic order. It integrates with research advances in multiple disciplines and bridges laws of physics, evolution in biology, and harmonious development of human society.

In the first part of this talk we review some prerequisites for and essential arguments involved in the construction of the thermal-ground-state estimate for the deconfining phase in the thermodynamics of SU(2) Quantum Yang-Mills theory and how this structure supports its distinct excitations. The second part applies deconfining SU(2) Yang-Mills thermodynamics to the Cosmic Microwave Background in view of (i) a modified temperature-redshift relation with an interesting link to correlation-length criticality in the 3D Ising model, (ii) the implied minimal changes in the dark sector of the cosmological model, and (iii) best-fit parameter values of this model when confronted with the spectra of the angular two-point functions TT, TE, and EE, excluding the low-$l$ physics. The latter, which is treated in an incomplete way because of the omission of radiative effects, is addressed in passing towards future work.

For a set of closed curved surfaces that resemble a Langmuir monolayer an energy is defined that depends only on the curvature of the surfaces interacting with the dimensions normal to the surfaces, that is, the thickness of these surfaces. The thickness, or depth, of the surfaces originates because of surface-particles with chains, that move freely on the inside of the surfaces at a certain depth. This is a purely geometrical description that does not depend on the introduction of ad hoc constants like the elastic constant. With a statistical mechanical model the equations of state are calculated for a gas of non-connected sphere-like surfaces in a volume. There are two states of which the lower temperature state is depending mostly on the interaction energy and surface properties, and the higher temperature state is depending mostly on sphere kinetic and volume properties. This results in aggregation of the sphere-like surfaces from many small ones to few large ones when lowering temperature and vice versa. The model allows for the calculation of the partition function and, when the emergence of the curvature - depth interaction is described as a phase-transformation, for the application of Noether’s theorem. Because of these properties the model is interesting in its own right apart from being an addition to existing elastic descriptions of surfaces.

Asphaltene precipitation and deposition pose significant operational challenges in both reservoirs and surface facilities by inducing formation damage. To understand the kinetics involved in asphaltene particle nucleation, growth, and aggregation, this study employed confocal microscopy and centrifuge-based methods under a unified set of experimental parameters. The acquired time-resolved particle size images were analyzed using MIPAR image processing software, while asphaltene mass yield was quantitatively evaluated through centrifugation. Experimental conditions were varied to study the effects of heptane concentration, asphaltene concentration, and shear rate. Notably, this investigation introduces, for the first time, the parameter of particle count as an additional variable influencing asphaltene mass production. This study aims to discern how particle count correlates with asphaltene mass yield over time. Results indicate that the minimum mean particle diameter was observed to be 2 microns, which progressively grew up to 80 microns. The mean particle diameter exhibited a positive correlation with both asphaltene concentration and shear rate, whereas an inverse correlation was seen with heptane concentration. Furthermore, the asphaltene mass yield was found to increase with greater asphaltene and heptane concentrations, as well as with higher shear rates. The relationship between mean particle diameter and mass yield was found to be nonlinear. In the early stages, a higher prevalence of small particles contributed to a greater total particle count, while at later stages, particle aggregation led to the formation of larger particles that influenced the overall asphaltene mass. The insights gained from understanding the relationship between particle diameter, count, and mass yield are crucial for advancing the fundamental science of asphaltene precipitation and deposition. These findings may also guide future research that relies solely on particle counts for assessing asphaltene deposition.

In this study, 12 organic waste materials were subjected to TG/DTG thermogravimetric analysis and DSC calorimetric analysis. These analyses provided basic information about thermochemical transformations and degradation rates during organic waste pyrolysis. Waste materials were chosen to cover the most abundant waste that can be found in the municipal solid waste stream. Based on TG results, kinetic parameters according to Coats–Redfern method were determined. The pyrolysis activation energy was the highest for cotton 134.5 kJ∙(mol∙K)-1 and the lowest for leather 25.2 kJ∙(mol∙K)-1. The DSC analysis showed number of transformations occurred during pyrolysis for each material. For each transformation, normalized energy required for transformation, or released during transformation were determined and then summarized to present energy balance. The study found that only for three waste materials: PET (-220.1 J⸱g-1), leather (-66.9 J⸱g-1), and chicken meat (-130.3 J⸱g-1) energy balance was negative, while the highest positive balance value was found for potato peelings (367.8 J⸱g-1). The obtained results may be applied for the modelling of energy and mass balance of municipal solid waste pyrolysis.

The reaction kinetics of burnt lime (CaO) in contact with sea water has been elucidated and compared to its behaviour in fresh water. In the first minutes of contact between burnt lime and water, it "slaked" as CaO reacted with water to yield calcium hydroxide (Ca(OH)2). Subsequently, calcium hydroxide reacted with magnesium, sulphate and carbonate from the sea water to yield magnesium hydroxide (Mg(OH)2), calcium sulphate dihydrate (gypsum, CaSO4·2H2O) and calcium carbonate (CaCO3), respectively. In a closed system of 1% CaO in natural sea water (where the supply of sulphate, magnesium and carbonate is limited), more than 90% reacted within the first 5 hours. It is foreseen that in an open system, like a marine fjord, it will react even faster. The pH 8 of sea water close to the CaO particle surface will immediately increase to a theoretical value of about 12.5 but will, in an open system with large excess of sea water, rapidly fall back to pH 10.5 being equilibrium pH of magnesium hydroxide. This is further reduced to < 9 due to the common ion effect of dissolved magnesium in sea water and then be diluted to the sea water background pH, about 8. Field test dosing CaO particles to sea water showed that the pH of water between the particles stayed around 8.

In an attempt to correct misunderstandings this article brings together the observations on Calcium, Myosin Binding Protein-C and Hypertrophic Cardiomyopathy in the basic function of cardiac muscle. A finding of many years ago is reiterated in a novel enzyme kinetic format with defined rate limiting step which makes CaATP the apparent substrate of the actomyosin cross-bridge. The relationship of these kinetics to recent observations on disruption of myosin binding protein-C is described along with how this bears on the understanding of the related cardiomyopathies.

The main goal of the Soil Moisture and Ocean Salinity (SMOS) mission over land surfaces is the production of global maps of soil moisture (SM) and vegetation optical depth (τ) based on multi-angular brightness temperature (TB) measurements at L-band. The operational SMOS Level 2 and Level 3 soil moisture algorithms account for different surface effects, such as vegetation opacity and soil roughness at 4 km resolution, in order to produce global retrievals of SM and τ. In this study, we present an alternative SMOS product which was developed by INRA (Institut National de la Recherche Agronomique) and CESBIO (Centre d’Etudes Spatiales de la BIOsphère). This SMOS-INRA-CESBIO (SMOS-IC) product provides daily SM and τ at the global scale and differs from the operational SMOS Level 3 (SMOSL3) product in the treatment of retrievals over heterogeneous pixels. Specifically, SMOS-IC is much simpler and does not account for corrections associated to the antenna pattern and the complex SMOS viewing angle geometry. It considers pixels as homogeneous to avoid uncertainties and errors linked to inconsistent auxiliary data sets which are used to characterize the pixel heterogeneity in the SMOS L3 algorithm. SMOS-IC also differs from the current SMOSL3 product (Version 300, V300) in the values of the effective vegetation scattering albedo (ω) and soil roughness parameters. An inter-comparison is presented in this study based on the use of ECMWF (European Center for Medium range Weather Forecasting) SM outputs and NDVI (Normalized Difference Vegetation Index) from MODIS (Moderate-Resolution Imaging Spectroradiometer). A 6 year (2010-2015) inter-comparison of the SMOS products SMOS-IC and SMOSL3 SM (V300) with ECMWF SM yielded higher correlations and lower ubRMSD (unbiased root mean square difference) for SMOS-IC over most of the pixels. In terms of τ, SMOS-IC τ was found to be better correlated to MODIS NDVI in most regions of the globe, with the exception of the Amazonian basin and of the northern mid-latitudes.

The article introduces the reader to the new thermodynamic potential of classical thermodynamics, called the J-potential. For the case of a homogeneous system, it vanishes, but it perfectly serves multiphase (heterogeneous) systems. The J-potential is especially important for the thermodynamics of capillary systems in colloidal science. The J-potential simplifies the derivation of the Neumann and Young equations, and has found application in the thermodynamics of thin films and the theory of strength of materials. In this work, for example, it was used to study the dependence of the chemical potential of a substance of a small bubble on the bubble size.

We propose a thermodynamic model describing the thermoelastic behavior of composition graded materials. The compatibility of the model with second law of thermodynamics is explored by applying a generalized Coleman-Noll procedure. We calculate the speeds of coupled first- and second-sound pulses, propagating either trough nonequilibrium or trough equilibrium states. We characterize several different types of perturbations, depending on the value of the material coefficients. Under the assumption that the deformation of the body can produce changes in its stoichiometry, altering locally the material composition, the possibility of propagation of pure stoichiometric waves is pointed out. Thermoelastic perturbations generated by the coupling of stoichiometric and thermal effects are analyzed as well.

This paper explores the Wilsonian renormalization group of probe-D-branes, focusing on the Dirac-Born-Infeld (DBI) action. The analysis involves deriving the constant of motion and formulating the Wilsonian renormalization group equation. The study extends to the infrared regime, considering both zero and non-zero temperatures. Additionally, thermodynamic aspects related to the functional form of the grand potential are discussed. The investigation provides insights into the renormalization of probe-D-branes and their thermodynamic properties.

Layered Ti3C2Tx MXene has been successfully intercalated and exfoliated with the simultaneous generation of a 3D silica network by treating its cationic surfactant intercalation compound (MXene-CTAB) with an alkoxysilane (TMOS) resulting in a MXene-silica nanoarchitecture that exhibits porosity along with the intrinsic properties of MXene (e.g., photothermal response). The ability of these new materials to produce thermal activation reactions of compounds previously adsorbed on MXene-SiO2 is shown here. For this purpose, the pinacol rearrangement reaction has been selected as a first model example, testing the effectiveness of NIR laser-assisted photothermal irradiation in these processes. This work shows that Ti3C2Tx – based nanoarchitectures open new avenues for applications that rely on the combined properties inherent to their integrated nanocomponents that could be extended to the broader MXene family.

Carbamazepine (CBZ) is one of the most common emerging contaminants released to the aquatic environment through domestic and pharmaceutical wastewater. Due to its high persistence through conventional degradation treatments, is considered a typical indicator for anthropogenic activities. This study tested the removal of CBZ through two different clay-based purification techniques: adsorption of relatively large concentrations (20-500 μmol L-1) and photocatalysis of lower concentrations (&lt;20 μmol L-1). The sorption mechanism was examined by FTIR measurements, exchangeable cations released, and colloidal charge of the adsorbing clay materials. Photocatalysis was performed in batch experiments under various conditions. Despite the neutral charge of carbamazepine, the highest adsorption was observed on negatively charged montmorillonite-based clays. Desorption tests indicate that adsorbed CBZ is not released by washing. The adsorption/desorption processes were confirmed by ATR-FTIR analysis of the clay-CBZ particles. A combination of synthetic montmorillonite or hectorite with low H2O2 concentrations under UVC irradiation exhibits efficient homo-heterogeneous photodegradation at μM CBZ levels. The two techniques presented in this study suggest solutions for both industrial and municipal wastewater, possibly enabling water reuse.

The high environmental impact of conventional methods of cooling and heating has increased the need for renewable energy deployment for covering thermal loads. Towards that direction, the proposed system aims at offering an efficient solar powered alternative, coupling a zeolite-water adsorption chiller with a conventional vapor compression cycle. The system is designed to operate under intermittent heat supply of low-temperature solar thermal energy (<90 °C) provided by evacuated tube collectors. A prototype was developed and tested in cooling mode operation. The results of separate components testing showed that the adsorption chiller was operating efficiently, achieving a maximum coefficient of performance (COP) of 0.65. With respect to the combined performance of the system, evaluated on a typical week of summer in Athens, the maximum reported COP was approximately 0.575, mainly due to the lower driving temperatures at a range of 75 °C. The corresponding mean energy efficiency ratio (EER) obtained was 5.8.

The aim of the present study is to provide new insights into the CO2 and CH4 adsorption using a set of biomass-based activated carbons obtained by physical and chemical activation of olive-stones. The adsorption behavior is analyzed by means of pure gas adsorption isotherms up to 3.2 MPa at two temperatures (303.15 and 323.15 K).The influence of the activation method on the adsorption uptake is studied in terms of both textural properties and surface chemistry. For three activated carbons the CO2 adsorption was more important than that of CH4. The chemically activation resulted in higher BET surface area and micropore volume that lead to higher adsorption for both CO2 and CH4. For methane the presence of mesopores seems to facilitate the access of the gas molecules into the micropores while for carbon dioxide, the presence of oxygen groups enhanced the adsorption capacity.

Thermal energy storage (TES) is a key technology to enhance the efficiency of energy systems as well as to increase the share of renewable energies. In this context, the present paper reports a literature review of the recent advancement in the field of adsorption TES systems. After a first introduction about different heat storage technologies, the adsorption TES working principle is explained and compared to the other technologies. Subsequently, promising features and critical issues at material, component and system levels are deeply analyzed and the ongoing activities to make this technology ready for marketing are introduced.

Abstract: Founders of quantum theory have pointed out the irreducibility of living systems to quantum mechanics. Quantum mechanics is never violated they rightfully argue but works under a set of active macroscopic constraints that selectively order the behavior of the micro components and these constraints are not reducible to the reversible, causally closed formalism of quantum mechanics. The whole of biological evolution is characterized by the production of increasingly more highly-ordered levels of such macroscopic constraints and biological evolutionary theory has no account for this either. It is assumed outside its theoretical first principles. In fact this generative macroscopic ordering, the production of increasingly more highly differentiated levels of order—more things, more kinds of things, cannot be explained within biological theory because it is generic to the universe itself. Irreducible to quantum mechanics this begs the question of fundamentality in physics. Fundamental laws in a universe defined by active macroscopic ordering, level-building, and differentiation must be able to causally cross levels, and more importantly explain why there is any level-building at all to begin with. The laws of thermodynamics are fundamental laws in this sense, and 4th Law path selection explains the generative universal ordering and differentiation (“complexification”).

1,3,5-Tris-(α-naphthyl)benzene is an organic non-electrolyte with notable stability of an amorphous phase. Its glassy and supercooled liquid states were previously studied by spectroscopic and calorimetric methods. However, the thermodynamic parameters of phase transitions available from the literature are inconsistent. In this work, the heat capacities of crystalline and liquid phases, the temperature dependence of the saturated vapor pressures, fusion and vaporization enthalpies were determined using differential and fast scanning calorimetry and verified using the estimates based on solution calorimetry. The structural features of 1,3,5-tris-(α-naphthyl)benzene are discussed based on the computations performed and the data on the molecular refractivity. The consistency between the values obtained by independent techniques was demonstrated. The deviations in the previously published data were attributed to possible polymorphism.

Starting from the analysis of the lack of positivity of the Cattaneo heat equation, the article addresses the thermodynamic relevance of the positivity constraint in irreversible thermodynamics, than is at least as important as the entropic constraints. The fulfillment of this condition in hyperbolic models leads to the parametrization of the concentration fields with respect to internal variables associated with the microscopic dynamics. Using Brownian motion theory as a landmarking example for deriving macroscopic transport equations from the equations of motion at the particle/molecular level, we discuss two typical problems involving hydrodynamic interactions at microscale: surface chemical reactions at a solid interface of a diffusing reactant, and mass-balance equations in a complex viscoelastic fluid, in which the physics of the interaction leads either to the overcome the parabolic diffusion model or to consider the parametrization of the concentration with respect to the degrees of freedom associated with the relaxation dynamics of the solvent fluid.

The purpose of this paper is to show a new approach to unify the theory of general relativity and quantum physics. For this, we rely on thermodynamics, fluid mechanics and the theory of information. We will then see that the Shannon entropy, Boltzmann and Von Neumann can be the source of gravity, which would be a form emerging. For this, we will study at first what is lacking for the unification of general relativity and physics. Secondly, we will explain the concept of entropic gravity by introducing calculations Erik Verlinde. Then we will explain the concept of entropy Boltzmann, Shannon, Von Neumann and the links between them. Then, we will modify Einstein's equations by transforming the tensor of perfect fluid in terms of entropy. Finally, we will link our theory with experience already carried out as part of a link between gravity and quantum theory.

Lactic acid production from lactose by Lactiplantibacillus plantarum AC 11S was studied. The influence of initial substrate concentration was investigated, and optimal pH and temperature were determined. An unstructured mathematical model was developed comprising equations for bacterial growth, substrate consumption, and product formation. The model was solved with different terms for specific growth rates considering substrate and/or product inhibition. The best bacterial growth and lactic acid production were achieved at pH = 6.5 and 30 oC. Production of lactic acid was mainly growth-associated and at substrate concentration over 15 g/L a considerable product inhibition was observed. The parameters of different models were determined and compared. While the modified Gompertz equation gave the best fit for biomass growth, a variant of the logistic equation including a term for product inhibition described in the best way the entire set of equations comprising bacterial growth, substrate consumption, and product formation at different initial substrate concentrations.

The work presents a mathematical model of a thermogravimetric curve for the growth and simultaneous sublimation of scale on a metal or alloy surface. Reduction of the reaction area as a result of the formation of oxides of alloying elements (for obtaining the basic oxide) is considered for the alloy. For metals, the case where this area is increased as a result of powder metal crushing is also considered. The equations that were obtained are employed to explain the kinetic curves of the mass change of the samples.

Large-scale volumetric fracturing is generally used during shale gas development. The return rate of fracturing fluid is low, and a large amount of slickwater will be retained in the reservoir. The adsorption and desorption of partially hydrolyzed polyacrylamide (HPAM), an additive commonly used in slickwater, on the surface of shale was studied using Longmaxi Shale from the Sichuan Basin. The experimental results showed that the mass ratio of the HPAM solution to shale reached saturation adsorption at 20:1 when the concentration of HPAM solution was 1000 mg/L and 25:1 when the concentration of HPAM solution was 500 mg/L. The mass ratio of the HPAM solution to shale was fixed at 25:1, and the adsorption equilibrium was reached at a HPAM concentration of 1000 mg/L when the aqueous solution temperature was 30°C and 800 mg/L when the aqueous solution temperature was 60°C. The Langmuir adsorption model yielded a better fit than the Freundlich adsorption model. The adsorption equilibrium time at 30°C was at 60 min for a HPAM concentration of 500 mg/L, while for a concentration of 1000 mg/L, it was at 90 min. The adsorption equilibrium time at 60°C was 40 min for a HPAM concentration of 500 mg/L, whereas it was 60 min for a HPAM concentration at 1000 mg/L. The pseudo-second order kinetics model yielded better fits than the pseudo-first order kinetics model. The adsorption of HPAM on shale was strong, and the adsorbed HPAM resembled cobwebs adhering to the shale surface. HPAM on the surface of shale after adsorption could resist the desorption capacity of water. However, when the amount of adsorbed HPAM on shale increased significantly, the amount of residual HPAM on the surface of the shale decreased rapidly during desorption in deionized water. The desorption of HPAM on the shale surface followed a modified desorption model. The higher the concentration of HPAM adsorbed on the shale surface was, the easier it was to desorb, the easier it was to be removed from the shale.

High levels of groundwater containing both arsenic and fluorine are prevalent, resulting in serious health problems when consumed as drinking water. This co-pollution phenomenon is widespread and requires urgent attention. The multiple forms of arsenic and arsenic-fluorine co-contamination pose a significant challenge to efficiently co-remove both substances. This research utilized a green and stable synthesis approach to create MgLaFe LDO heterostructures, which were anchored on α-MnO2 nanowires. The materials comprise magnesium and lanthanum elements with a powerful attraction towards fluoride ions, elemental iron, which can establish stable compounds with arsenate, and MnO2, which can effectively oxidize arsenous acid, thereby enabling efficient co-removal of arsenic and fluorine. The efficient oxidation process of the MnO2 nanowire and the prompt ion adsorption process of the LDO work together synergistically. The adsorption performance was assessed through isotherm and kinetic fitting. Chemisorption was found to be the process for As(Ⅲ), As(V), and F- adsorption, with As(Ⅲ) going through monolayer adsorption on the surface of MnO2 nanowires, while As(V) and F- were mainly adsorbed by multilayer process on LDO. The maximum adsorption capacities were 111.76 mg/g, 230.51 mg/g, and 765.10 mg/g for As(Ⅲ), As(V), and F-, respectively. The XPS analysis provided further elucidation on the adsorption mechanism of the MnO2@LDO heterostructure, detailing each component's role in the process. The results confirm the successful construction of the heterostructure and its efficient coupling of oxidation and adsorption.

Leather waste was carbonized at 800 °C in inert atmosphere. The resulting biochar was coated in situ with polypyrrole nanotubes produced by the oxidation of pyrrole in the presence of methyl orange. The composites of carbonized leather with deposited polypyrrole nanotubes of various composition were compared with similar composites based on globular polypyrrole. Their molecular structure was characterized by infrared and Raman spectra. Both conducting components formed a bicontinuous structure. The resistivity determined by four-point van der Pauw method was monitored as a function of pressure applied up to 10 MPa. The typical conductivity of composites was of the order of tenths to units S cm−1 and it was always higher for polypyrrole nanotubes than for globular polypyrrole. The conductivity decreased by 1–2 orders of magnitude after treatment with ammonia but still maintained a level acceptable for applications operating under non-acidic conditions. The composites were tested for dye adsorption, viz. cationic methylene blue and anionic methyl orange, using UV-spectroscopy. The composites are designed for the future use as functional adsorbents controlled by the electrical potential.

Air pollution is related to the development of people's livelihood. As one of the main pollutants in the air, formaldehyde affects people's physical and mental health. In order to remove formaldehyde and better protect the health of residents, it is very necessary to develop efficient adsorption materials. In this study, a cellulose composite aerogel Microcrystalline Cellulose/ N-(2- aminoethyl) -3- aminopropyl methyl dimethoxysilane (MCC/APMDS) modified by APMDS was explored. The pore volume and specific surface area of the modified aerogel decreased, the average pore diameter increased, and the adsorption capacity of formaldehyde was stronger. The adsorption experiment shows that the sample prepared under the conditions of APMDS dosage of 6 wt%, reaction time of 4 h and reaction temperature of 90℃ has the largest average pore size (14.56 nm) and the largest formaldehyde adsorption capacity (9.52 mg/g). The excellent adsorption of the composite aerogel is due to high porosity and rich active amino groups on the surface. This study provides valuable information for the preparation of adsorption materials with high formaldehyde adsorption capacity for air purification.

Even in the first quarter of XXI century, the presence of organic dyes in wastewaters is a normal occurrence in a series of countries, and being these compounds toxics, their removal from these waters is of a necessity. Among the separation technologies, adsorption processing appeared as one of the most widely used to reach this goal. The present work reviewed the most recent approaches (first half of 2021 year) about the use of a variety of adsorbents on the removal of, also, a variety of organic dyes of different nature.

The processes of the sublimation and thermal decomposition of the 1‐ethyl‐3‐methylimidazolium hexafluorophosphate ionic liquid (EMImPF6) were studied by a complex approach including Knudsen effusion mass spectrometry, IR and NMR spectroscopy, and quantum chemical calculations. It was established that the vapor over liquid phase primarily consists of decomposition products under equilibrium conditions. Otherwise, the neutral ion pairs are the only vapor components under Langmuir conditions. To identify the nature of the decomposition products an experiment on the distillation of the ionic liquid was performed and the collected distillate was analyzed. It was revealed by the IR and NMR spectroscopy that EMImPF6 decomposes to substituted imidazole‐2‐ylidene (C6N2H10PF5) and HF. The measured vapor pressure of C6N2H10PF5 reveals a very low activity of the decomposition products (&lt;10–4) in the liquid phase. The absence of significant accumulation of decomposition products in the condensed phase makes it possible to determine the enthalpy of sublimation of the ionic liquid assuming its unchanged activity. The thermodynamics of the EMImPF6 sublimation was studied by Knudsen effusion mass spectrometry. The formation enthalpy of EMImPF6 in ideal gas state was found from combination of the sublimation enthalpy and formation enthalpy of ionic liquid in the condensed state. The obtained value is in good agreement with those calculated by quantum chemical methods.

A simple line of reasoning, based on the most fundamental concepts of thermodynamics, yields some intriguing results for a better understanding of the processes occurring in the observable Universe. Gravitational mass must be continuously generated within an expanding thermodynamic system for this system to remain closed. The Second Law is a direct consequence of this production of mass. Simple expressions for the entropy and temperature of the Universe were obtained and the results agree well with observable values. Furthermore, it is demonstrated that the conservation laws within the Universe are independent of its energy density. Based on the solution for the quantum state of the Universe, it is conjectured that the Second Law is incomplete and must be complemented to a conservation law, which takes into account the growth of the amount of information within the Universe. Once the Second Law is complemented to a conservation law, the importance of mass generation within the Universe becomes well pronounced – not only gravitational effects play the role of an organising force, but also the amount of mass within the Universe defines both the amount of information within the Universe and the level of the Universe’s complexity.

Cathinone is a natural stimulant found in Catha edulis and commonly used in new psychoactive substances. The objective of this study was to examine the disposition kinetics and metabolic profile of cathinone and its metabolite cathine through a single oral dose of cathinone administration in rats. Cathine and cathinone concentrations were identified and quantified using ion trap liquid chromatography (LC-IT/MS), while the metabolic profile was determined using the quadrupole time of flight UPLC-QTOF/MS method in the serum, brain, lung, liver, kidney, and heart over a period of 0, 0.5, 2.5, 6, 12, 24, 48, and 72 hours. The findings revealed a dynamic interplay between the pharmacokinetics of cathinone and its impact on organ-specific biomarkers. The distribution of cathinone and cathine was determined in serum, brain, heart, lung, kidney, and liver. The highest concentration of cathinone was found in the kidney at 1438.6 ug/L. It gradually decreased to 1.97 within 48 hours and disappeared after 72 hours. Within half an hour, cathinone levels in the lungs, liver, and heart were found to be 859, 798.9, and 385.8 ug/L, respectively. However, within 2.5 hours, these levels decreased to 608.1, 429.3, and 309.1 ug/L and kept decreasing until they became undetectable after 24 hours. The concentration of cathinone in the rat brain reduces quickly, dropping to undetectable levels within six hours, with levels decreasing from 712.7 ug/L after just 30 minutes. In the brain and serum, cathine reached its highest levels at 2.5 hours, while in other organs, it peaked at 0.5 hours. This indicates that the conversion of cathinone to cathine is slower in the brain and serum. The study found that cathinone's pharmacokinetics have a significant impact on organ-specific biomarkers. After administering the cathinone, there was a sharp change in biomarker levels, particularly in the liver and brain, during the initial hours. It is essential to investigate the correlation between the changes in biomarkers found in the brain and the levels of cathinone and cathine. The results have significant implications for drug development, pharmacovigilance, and clinical practices involving cathinone. In conclusion, this comprehensive analysis of cathinone's impact on organ-specific biomarkers provides a basis for informed decision-making in medical practices and further research into the cathinone's pharmacological properties.

Gold- and MnO₂- nanozymes are well-known for their enzyme-like activity. In this regard, initially, gold- and MnO₂- nanozymes were synthesized by simple and green methods. Afterward, the kinetic studies were performed using the Michaelis–Menten model for both gold- and MnO₂- nanozymes. The kinetic parameters including K_m and V_max were calculated via the construction of the linear plot of Lineweaver–Burk for both nanozymes. The results showed a V_max and K_m of 185 nM sec^-1 and 47 nM sec^-1 for the gold- and MnO₂- nanozymes, in order. The ratio of V_max(gold)/V_max(MnO₂) was found to be about 4.0 which pointed that the catalytic efficiency of gold-nanozymes is 4.0-fold higher than the catalytic efficiency of MnO₂- nanozymes. The K_m value was found to be 0.72 mM and 1.6 mM for the as-prepared gold- and MnO₂- nanozymes, respectively, and the K_m of MnO₂-nanozymes is 2.2-fold higher than that of gold nanozymes. Since the Km shows the affinity of substrate for binding to nanozyme active nodes (lower K_m=higher affinity), it is consultable that the substrate affinity toward MnO₂-nanozymes is 2.2-fold lower than that of the gold-nanozymes. Considering the above results, the as-prepared gold nanozymes are very stronger peroxidase-like mimics than the metal oxide MnO₂-nanozymes.

In the context of the COVID-19 epidemic, and on the basis of the Theory of Dynamical Systems, we propose a simple model for the expansion of contagious diseases, with a particular focus on viral respiratory tracts. The infection develops through contacts between contagious and exposed people, with a rate proportional to contact duration and turnover, inversely proportional to the efficiency of protection measures, and balanced by the average immunological response. The obvious initial exponential increase is readily hindered by the size reduction of the exposed population. The system converges towards a stable attractor whose value is expressed in terms of the ratio C/D of contamination vs decay factors. Decreasing this ratio below a critical value leads to a tipping point beyond which the epidemic is over. By contrast, significant values of C/D may bring the system through a bifurcating hierarchy of stable cycles up to a chaotic behaviour.

Activated carbon (AC) is an effective adsorbent for creatinine removal in hemoperfusion. However, the hemocompatibility and adsorption capacity of AC was required to be improved furthermore. Heparin, a widely used anticoagulant biomacromolecule, could improve the hemocompatibility of the absorbents in different ways based on its molecular weight. Thus, it was necessary to study the surface modification with unfractionated heparin (UFH) or low molecular weight heparin (LMWH) on improvement of hemocompatibility and adsorption. In this study, UFH and LMWH were respectively grafted on AC through polyethyleneimine as an intermediate layer. The modification of AC about morphology, mechanical strength and pore structure was characterized by XPS, SEM, TA and BET. It was found that compared with AC, the morphology and mechanical strength AC-UFH and AC-LMWH could be well maintained, but the BET surface was decreased due to the grafting of macromolecules. Furthermore, AC-UFH and AC-LMWH showed the better hemocompatibility on protein adsorption, APTT and platelet activation compared with AC, in which AC-LMWH had lower fibrinogen adsorption and longer APTT than AC-UFH. Besides, it was found that AC, AC-UFH and AC-LMWH had no significant effect on blood cell composition. Finally, the adsorption capacity of adsorbents for creatinine was evaluated. Although there was no significant difference between AC-UFH and AC-LMWH, it was found that heparin could be interacted with creatinine to enhance the adsorption capacity when compared with AC-PEI. This study deepened the understanding of anticoagulation of heparinized surface and provided a theoretical basis for adsorbents in hemoperfusion.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2&gt;CH4&gt;N2.

Thermodynamics and phase transitions of magnetic Anti-de Sitter black holes are studied. We consider an extended phase space thermodynamics with the cosmological constant being a thermodynamic pressure and the black hole mass is treated as a chemical enthalpy. The extended phase space thermodynamics of black holes mimics the behavior of the Van der Walls liquid. Quantities conjugated to the coupling of nonlinear electrodynamics (NED) and a magnetic charge are obtained. Thermodynamic critical points of phase transitions are investigated. It is demonstrated that the first law of black hole thermodynamics and the generalized Smarr relation take place. The Joule--Thomson adiabatic expansion of NED-AdS black holes is studied. The dependence of inversion temperature on pressure and the minimum of inversion temperature are found.