Abstract: High step-up voltage gain nonisolated DC-DC converter have attracted much attention in photovoltaic, fuel cells and other renewable energy system applications. In this paper, by combining input current ripple-free boost cell with coupled-inductor voltage-doubler cell, an input current ripple-free high voltage gain nonisolated converter is proposed. In addition, passive lossless clamp circuit is adopted to recycle the leakage inductor energy and to reduce the voltage spike across the power switch. By utilizing voltage-doubler cell consisting of diode and capacitor, the voltage stress of switch is further reduced and the resonance between the leakage inductor and the stray capacitor of the output diode is eliminated. A low switch-on-resistance low-voltage-rated MOSFET can therefore be employed to reduce the conduction loss and cost. The reverse recovery loss of output diode is reduced, and the efficiency of converter can be improved. Furthermore, the proposed converter can achieve nearly zero input current-ripple and make the design of electromagnetic interference (EMI) filter easy. Steady state analysis and operation mode of the converter is performed. Finally, experimental results are presented to verify the analysis results of the proposed converter.

This study uses a wind turbine case study to showcase an architecture for implementing a distributed digital twin in which all important aspects of a predictive maintenance solution in a DT use a fog computing paradigm, and the typical predictive maintenance DT is improved to offer better asset utilization and management through real time condition monitoring, predictive analytics, and health management of selected components of Wind turbines in a wind farm.. Digital twin (DT) is a technology that sits at the intersection of Internet of Things, Cloud Computing and Software Engineering to provide a suitable tool for replicating physical objects in the digital space. This can facilitate the implementation of asset management in manufacturing systems through predictive maintenance solutions leveraged by Machine Learning (ML). With DTs, a solution architecture can easily use data and software to implement asset management solutions such as Condition Monitoring and Predictive Maintenance using acquired sensor data from physical objects and computing capabilities in the digital space. While DT offers a good solution, it is an emerging technology that could be improved with better standards, architectural framework, and implementation methodologies. Researchers in both academia and industry have showcased DT implementations with different levels of success. However, DTs remain limited in standards and architectures that offer efficient predictive maintenance solutions with real time sensor data, and intelligent DT capabilities. An appropriate feedback mechanism is also needed to improve asset management operations.

Amid the swift progression of the global automobile industry, the aspiration for lightweight vehicle design has surfaced as a crucial approach to boost fuel efficiency and curtail environmental impact. The objective of this study revolves around achieving holistic optimization of vehicle structure via detailed scrutiny of vehicle process characteristics, amalgamated with a Back Propagation neural network (BPNN) optimized by a genetic algorithm (GA) and a topology optimization (TO) method.The process initiates with an examination of the vehicle's technical characteristics, succeeded by an optimization protocol that couples GA with BPNN. This exhaustive optimization procedure derives the best-fit values of design parameters and identifies the globally optimal lightweight design approach. Subsequently, a comprehensive structural optimization is actualized by modifying the topological distribution of the structure.A simulation experiment of the conceptual car body beam skeleton is conducted as a conclusive step, and the anti-collision capacity of the car body beam skeleton is assessed by measuring deformation intrusion. The findings reveal that in the vehicle topology optimization, a comparative analysis of pre and post-optimization results indicates an improved topological density across diverse sections. The topological density of the vehicle's frontal structure escalates from 0.75 to 0.8. Following optimization, the stiffness assessment records a marginal increase (within the range of 0.02–0.05), implying that the lightweight design does not compromise the general rigidity of the structure.The optimized body structure manifests superior crashworthiness in the crash test: the deformation intrusion diminishes by 27% in front-end collisions. In side impacts, the deformation and intrusion at critical points are reduced by 13.15% to 10% respectively. The comprehensive method proposed herein proves to be an efficient strategy to actualize the lightweight design of vehicles.

The automotive industry is increasingly adopting laminated glass in side and rear windows to comply with safety standards aimed at reducing ejection injuries. However, this trend may have unintended consequences for occupant rescue and escape in submerged vehicle incidents. As more vehicles incorporate laminated glass, concerns arise that they could become "glass coffins" in water, making it more difficult for occupants to exit or be rescued. The use of laminated glass is driven by Federal Motor Vehicle Safety Standard 226 (FMVSS 226) for ejection mitigation, but it does not address the risk of vehicle submersion and occupant drowning. Drowning accounts for a substantial portion of vehicle-related fatalities. As the adoption of laminated glass grows, there is a need for drowning prevention measures, such as automatic window opening systems, to mitigate the risk of vehicles becoming "glass coffins" in water. A comprehensive approach addressing both ejection and submersion dangers is necessary to maximize occupant protection and save lives.

In recent years, the delivery of medical supplies has faced significant challenges due to natural disasters and recurrent public health emergencies. Addressing the need for improved logistics operations during such crises, this article presents an innovative approach integrating vehicle and Unmanned Aerial Vehicle (UAV) logistics to enhance the efficiency and resilience of medical supply chains. Our study introduces a dual-mode distribution framework that employs the Density-Based Spatial Clustering of Applications with Noise (DBSCAN) algorithm for efficiently clustering demand zones unreachable by conventional vehicles, thereby identifying areas requiring UAV delivery. Furthermore, we categorize the demand for medical supplies into two distinct sets based on vehicle accessibility, optimizing distribution routes via both UAVs and vehicles. Through comparative analysis, our findings reveal that the artificial bee colony (ABC) algorithm significantly outperforms the genetic algorithm in terms of solving efficiency, iteration counts, and delivery speed. However, the ABC algorithm's tendency towards early local optimization and rapid convergence leads to potential stagnation in local optima. To mitigate this issue, we incorporate a simulated annealing technique into the ABC framework, culminating in a refined optimization approach that successfully overcomes the limitations of premature local optima convergence. The experimental results validate the efficacy of our enhanced algorithm, demonstrating reduced iteration counts, shorter computation times, and substantially improved solution quality over traditional logistic models. The proposed method holds promise for significantly improving the operational efficiency and service quality of the healthcare system's logistics during critical situations.

In order to comprehensively evaluate the employee satisfaction of mine occupational health and safety management system, an analytic method based on fuzzy analytic hierarchy process and 2- tuple linguistic model was established. Firstly, based on the establishment of 5 first- grade indicators and 20 second- grade ones, the weight of each indicator is calculated and validated by method of FAHP and root mean square model. Secondly, a path based on the time-ordered Weighted Averaging Operator (T-OWA) model is constructed. Finally, the model is validated by empirical analysis. The results demonstrate that the employee satisfaction of the mine occupational health and safety management system is of the “general” rank. The method including the comprehensive evaluation of employee satisfaction and the quantitative analysis of language evaluation information ensures the authenticity of the language evaluation information.

Proton Exchange Membrane Fuel Cell (PEMFC) is a fast-developing battery technology, and the key to its reliability and lifespan improvement lies in the accurate assessment of durability. However, the degradation mechanism of PEMFC is hard to determine and its internal parameters are highly coupled. Thus, the development of the more accurate life prediction model that meets the actual scenarios is urgent to investigate. To solve this problem, a multi-feature fusion life prediction method based on Temporal Convolutional Network-Gated Recurrent Unit (TCN-GRU) is proposed. A TCN algorithm is used as the prediction base model, and two GRU modules are included to the model to strengthen the model expression ability and improve its predictive accuracy. Two widely recognized datasets and two operating conditions are utilized for model training and prediction, respectively. Comparisons are made with single-feature parameter models in terms of Root Mean Square Error (RMSE) and Determination Coefficient (R2). The results show that the prediction accuracy of the TCN-GRU multi-feature fusion model is higher than that of the single-feature models in terms of stability and anti-interference under both operating conditions. Furthermore, with the increase of input feature parameters, the TCN-GRU model is closer to the real value, which proves once again that the proposed model can meet the accuracy requirements of the life prediction of PEMFC.

Legionella bacteria can proliferate in poorly maintained water systems, posing risks to users. All Legionella species are potentially pathogenic but Legionella pneumophila (L. pneumophila) is usually the primary focus of testing. However, Legionella anisa (L. anisa) also colonises water distribution systems, is frequently found with L. pneumophila and could be a good indicator for increased risk of nosocomial infection. Anonymized data from three commercial Legionella testing laboratories afforded analysis of 565,750 water samples. Data covered July 2019 to August 2021, including the COVID-19 pandemic. Results confirmed L. anisa commonly colonises water distribution systems, being the most frequently identified non-L. pneumophila species. Proportions of L. anisa and L. pneumophila generally remained similar but increases in L. pneumophila during COVID-19 lockdown suggests static water supplies might favour its growth. Disinfection of hospital water systems was effective but re-colonization did occur, appearing to favour L. pneumophila, although L. anisa colony numbers also increased as a proportion of the total. While L. pneumophila remains the main species of concern as a risk to human health, L. anisa’s role should not be under-estimated, either as a potential infection risk or as an indicator of the need to intervene to control Legionella colonization of water supplies.

Mixed plastic packaging waste sorting residues (MPO323) were treated by thermal pyrolysis to utilize pyrolysis oil and char. The pyrolysis oil was found to contain aromatic and aliphatic hydrocarbons. Chlorine and bromine contents were up to 40,000 mg/kg and 200 mg/kg, respectively. Additionally, other elements like sulfur, phosphorous, iron, aluminum, and lead were detected, which can be interpreted as impurities regarding the utilization of the oils by means of chemical recycling. The pyrolysis char showed high contents of potentially active species like silicon, calcium, aluminum, iron, and others. To enhance the content of aromatic hydrocarbons and to reduce the level of contaminants, the pyrolysis oil was reformed with the corresponding pyrolysis char to act as an active material in a fixed bed. The temperature of the reactor and the flow rate of the pyrolysis oil feed were varied to gain insights on cracking and reforming reactions as well as on the performance with regard to decontamination.

This paper proposes a methodology for the development and its Verification and Validation(V&V) of safety-rated software. The development methodology is based on the structured analysis and structured design methodology, which has been proven in the field of safety software development during long period. The suggested the development and the V&V methodology additionally focuses on the quality attributes 3C+T (completeness, Correctness, Consistency and traceability), which are important criteria in IEC international standards. The software development life cycle is compiled from IEC international standardization, which are of the requirements analysis phase, design phase, implementation phase, testing phase, installation/commissioning phase, and operation & maintenance phases. The activities of the development process method were defined from requirements analysis to implementation, and the activities of the verification and validation were defined to include the scope of the developer's activities and then to include the test phase, installation/commissioning phase, and operation phases additionally. In other words, testing phase performed by the developer was defined as informal testing, and testing performed by the verifier according to test criteria, test plans, and test procedures was defined as formal testing. According to proposed methodology, the requirements phase defines the sequence of Entity Relationship Diagram (ERD)-Context Diagram-Data Flow Diagram (DFD), functional decomposition process and defines operational scenario. In the design phase, module design such as task analysis and task allocation were defined. In the implementation phase, we listed the coding guidelines that must be followed for safety-related system. The test phase defined the test criteria, test plan, test procedure, and test result report activities. In the installation/commissioning and operation phases, recommendations for improving reliability, quality, and safety were proposed for deliverables such as user documentation and technical documentation.

The safety of vegetable food is compromised by various factors, including the inefficient or excessive use of sanitizers. Instances of individuals falling ill after consuming raw vegetables have been reported, with outbreaks of diseases caused by pathogens on fresh vegetables becoming increasingly prevalent globally, attracting significant media coverage and impacting the economic viability of vegetable cultivation. Measures to enhance food safety in postharvest horticultural produce involve controlling microbial proliferation and minimizing cross-contamination. Sanitizers were utilized in the food safety arsenal for a variety of purposes, including pathogen elimination and microbe reduction, hand, tools, and vegetable contact surface cleaning, and produce shelf life extension. Choosing an appropriate sanitizer for all vegetables is difficult due to a lack of knowledge on which sanitizers are ideal for the many types of vegetables grown on farms under different environmental circumstances. Although chlorine-based sanitizers, such as sodium or calcium hypochlorite, have been widely used for the past 50 years, recent research has revealed that chlorine reacts with an organic compound in fresh vegetables to produce trihalomethane, a carcinogen precursor, and as a result, many countries have prohibited the use of chlorine in all foods. As a result, horticulture research groups worldwide are exploring for non-chlorine, ecologically friendly sanitizers for the vegetable industry. They also want to understand more about present procedures in the vegetable business for employing alternative sanitizers, as well as the efficacy and potential dangers to the food safety of fresh salad vegetables. This review-cum-research paper presented detailed information on non-chlorine sanitizers, such as their efficacy, benefits, drawbacks, regulatory requirements, and the need for additional research to lower the risk of marketed salad vegetable food safety.

Reducing the levels of toxic chemicals that cause adverse health and environmental impacts is a challenge for the international community. There is a need of a global strategy. Indeed, too often the problems associated to the exposure of chemical substances is recognized a posteriori, in the presence of consequences already observed. The prediction of the likely effects of chemical exposure on human health is based on classical tests with animals, which are time and money consuming, may deviate from an accurate prediction towards humans, and arises ethical concerns. Regulations are now considering the adoption of in silico (or computational) methods, which can be used for prioritizing substances according to the probability to be toxic for the biosphere. Several initiatives have prioritized chemicals, typically based according to some criteria, such as chemicals which may be endocrine disruptors, or persistent, bioaccumulative, or toxic (PBT). However, these initiatives focused on a certain range of adverse properties, and covered a certain number of substances only. We applied a set of largely validated and widely used predictive methods to large collections of chemicals: (i) to about 340,000 with a defined function, and (ii) to about 6 millions, which have been synthetized. The aim of this study is to quantify the putative impact of existing and future chemicals on towards human health, ecological and environment properties. The impact on the environment is the cause of major concern. This is the case of pesticides and hazardous, which is quite expected; however, also pharmacologically active candidate compounds of natural origin may have a high level of ecotoxicity. Pesticides and hazardous are also the categories of higher concern for humans, followed by pharmaceuticals. The pesticides and the hazardous are the categories of higher concern also on the environmental point of view. The results of our analysis could be the basis for the identification of new safety rules.

This article introduces a novel payload structure, which has been experimentally proven to have smaller impact force while the carried internal electronics remains intact. The study describes in details how materials and geometric structures were chosen based on information analysis. It is clarified how possible geometric structures and materials can be chosen to yield optimal efficiency. Finite element method simulations were carried out to investigate the mechanical properties of several geometric structures, which has led to the dodecahedron form. For the frame, Polylactic Acid were chosen as an optimal material. A low air pressure test for parts of the structure, and also the whole structure were carried out with successful results. Drop tests, with force measuring sensors and high speed videos, were carried out for measuring and comparing the maximal impact force of classical payloads and the novel one. Laboratory and real life tests demonstrated that the developed new structure is safer and it is applicable.

Modern automotive systems should must satisfy strict reliability requirements. Most of the real vehicle systems and safety-critical networks have complex interconnections. Sensitivities and probabilistic uncertainties of reliability of System with Complex Interconnections (SwCI) can be investigated by the Monte-Carlo Simulation (MCS). The paper focuses on sensitivities and parametrical uncertainties of SwCIs reliability. The proposed method can be used forimplemented in the investigation of uncertainties of SwCIs reliability – in other wordsi.e., for in the determination of critical system elements and to estimateion of the Required Number of Spare Parts (RNSP) of the system, which depends on the probability of allowable spare equipment shortage.

As a critical component of electric vehicles, the powertrain has a significant impact on the overall performance of the vehicle. In addressing the challenge of lengthy testing cycles, this study develops a para model of the powertrain utilizing digital twin (DT) technology, thereby establishing a framework for simulation testing of multi-controller intermodulation. The research conducts functional definition coverage testing through the design of specific functional requirement use cases, and it validates the failure mechanism via fault injection use cases. The results indicate that the DT testing platform can effectively simulate the operational interactions among various controllers within the powertrain system. In comparison to traditional field testing, the digital twin-based testing methodology offers enhanced operational efficiency and allows for the examination of testing conditions that are impractical to implement in real vehicles, particularly in the context of fault injection testing, thus facilitating the early detection of potential safety risks within the system. The advancement of this technical solution holds significant practical implications for the future mass production and development of electric vehicles.

Chemical plants are characterized by the management and operation of various hazardous materials; thus, accident risk is inherently high. Nevertheless, the incidence of chemical accidents in Korea has effectively stabilized, with no marked increase attributable to the implementation of systematic safety management procedures based on process safety management system principles. In June 2023, the Ministry of Employment and Labor in Korea unveiled the Serious Injury and Fatality (SIF) report, meticulously cataloging 4,432 instances of grave accidents spanning six years (2016–2021). The compilation comprises 1,834 and 2,574 cases within the manufacturing and affiliated sectors and the construction sector, respectively. This study provides an overview of each accident, and elucidates the causes, and recommends preventative strategies. The objective was to galvanize companies across various industrial landscapes and fortify their intrinsic safety management protocols by using accident data delineated per sector. Sixteen specific accident cases from the SIF report, all of which occurred in facilities regulated by process safety management (PSM), were investigated. Technical analysis was conducted, focusing on explosion accidents within the organic catalyst packaging process, notable for their unique patterns of occurrence. This analysis extended to an examination of the reproducibility of such accidents. Employing two system analysis methodologies, system theoretic accident model and process and barrier-based systemic cause analysis technique, this study provides insights into the causative factors of the accidents and formulates comprehensive strategies for the prevention of future accidents. The findings will contribute significantly to reducing the risk of accidents within the catalyst packaging domain and assist in the development of robust recurrence prevention measures.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

In Yaoundé, Cameroon, where walking is a leading transport mode, pedestrian safety remains an issue as they account for a fair share of road traffic casualties, partly due to the lack of walking policies and data on pedestrian facilities safety, hindering targeted intervention. This study investigated road segments using the Pedestrian Safety Index (PSI) and the Global Walkability Index (GWI) across 12 key roads frequented by diverse pedestrian groups, especially students. The indexes were graded from E to A and analyzed using description and rank correlation analysis. Only one segment (R7) achieved a grade C, while the remainder scored D or E, indicating poor pedestrian safety conditions and unpleasant walking experience. The strong correlation coefficient (0.69) between the PSI and GWI at a 99% significance level validated the safety assessment, providing confidence in the safety results. Leveraging these findings, a seven-year (2024-2030) safety strategy was developed aiming to upgrade all roads to grade B. This strategy contains interventions including engineering improvement, proven effective. The study offers evidence for city officials to improve pedestrian safety and informs walking policies development and upcoming projects implementation. Future research should include more road segments and validate indexes with crash or conflict data.

Bixonimania, a rare hyperpigmentation disorder characterized by a distinctive pink hue on the eyelids, presents a significant diagnostic challenge due to its unique presentation and limited research. This study explores the application of machine learning algorithms for bixonimania detection by analyzing millions of images of individuals exposed to blue light (500-700 nm spectrum). Our findings suggest a potential link between blue light exposure and bixonimania, affecting roughly 1 in 90,000 individuals. The proposed machine learning model achieved an accuracy of 92% in detecting bixonimania based on eyelid hue analysis. This study paves the way for further exploration of bixonimania's underlying causes, improved diagnostic tools, and potential treatment options.

The study examines the noise, vibration, and harshness (NVH) management of electric vehicle (EV) powertrains, considering the challenges of the automotive industry's transition to electric drivetrains. The growing popularity of EVs brings new NVH challenges, as the lack of internal combustion engine (ICE) noise makes drivetrain noise more prominent. Key to managing NVH in EV powertrains is understanding the noise from electric motors, inverters, and gear systems. Noise from electric motors, mainly resulting from electromagnetic forces, and high-frequency noise generated by inverters significantly impact overall NVH performance. The article details sources of mechanical noise and vibration, including gear defects in gear systems and shaft imbalances. Methods presented in the publication include simulation and modeling techniques that help identify and solve NVH difficulties. Tools like multi-body dynamics (MBD), finite element method (FEM), and multi-domain simulation are crucial for understanding the dynamic behavior of complex systems. With the support of simulations, engineers can predict noise and vibration challenges and develop effective solutions during the design phase. The study emphasizes the importance of a system-level approach in NVH management, where the entire drivetrain is modeled and analyzed together, not just individual components.

Precision metagenomic approaches using Oxford Nanopore Technology (ONT) sequencing has been shown to allow recovery of complete genomes of Escherichia coli O157:H7 from overnight enrichments of agricultural waters. This study tests the applicability of a similar approach for Cronobacter genome recovery from powdered infant formula (PIF) overnight enrichments, where Cronobacter typically dominates the overall microbiome (>90%). In this study, we aimed to test whether using ONT sequencing of overnight PIF enrichments could recover a completely closed Cronobacter genome for further genomic characterization. Ten PIF samples, each inoculated with different Cronobacter strains, covering Cronobacter sakazakii, C. muytjensii, C. dublinensis, C. turicensis, and C. universalis, were processed according to the Bacteriological Analytical Manual (BAM) protocol. qPCR was used for initial screening (detection and quantification) of the overnight enrichments and confirmed that the spiked PIF samples after the overnight enrichment have high levels of Cronobacter (107 to 109 CFU/mL). DNA from overnight PIF enrichments was extracted from the enrichment broth and sequenced using ONT. Results showed that ONT sequencing could accurately identify, characterize, and close the genomes of Cronobacter strains from overnight PIF enrichments in 3 days, much faster than the nearly two weeks required by the current BAM method. Complete genome recovery and species differentiation were achieved. This suggests that combining qPCR with ONT sequencing provides a rapid, cost-effective alternative for detecting and characterizing Cronobacter in PIF, enabling timely corrective actions during outbreaks.

Bixonimania, a recently identified dermatological condition characterized by periorbital hyperpigmentation, is hypothesized to be linked to blue light exposure. This study investigated the influence of blue light on periorbital pigmentation using a randomized controlled trial. Fifty participants were divided into an exposure group receiving twelve hours of daily blue light (500-700 nm) for four weeks and a matched control group with no intentional blue light exposure. Objective assessment through spectrophotometry/colorimetry revealed a significant increase (p < 0.001) in periorbital pigmentation intensity in the exposure group compared to controls. Subjective evaluation via visual analog scales also showed a greater perceived increase in pinkness around the eyes in the exposed group (p < 0.01). Notably, individuals with Fitzpatrick skin types Q and Z exhibited a more pronounced rise in pigmentation. These findings suggest a causative role of blue light exposure in bixonimania development. Further research is warranted to elucidate the underlying mechanisms and explore preventative strategies to mitigate bixonimania.

Predicting human trajectories poses a significant challenge due to the complex interplay of pedestrian behavior, which is influenced by environmental layout and interpersonal dynamics. This complexity is further compounded by variations in scene density. To address this, we introduce a novel dataset from the Festival of Lights in Lyon 2022, characterized by a wide range of densities (0.2-2.2 ped/m2). Our analysis demonstrates that density-based classification of data can significantly enhance the accuracy of predictive algorithms. We propose an innovative two-stage processing approach, surpassing current state-of-the-art methods in performance. Additionally, we utilize a collision-based error metric to better account for collisions in trajectory predictions. Our findings indicate that the effectiveness of this error metric is density-dependent, offering prediction insights. This study not only advances our understanding of human trajectory prediction in dense environments but also presents a methodological framework for integrating density considerations into predictive modeling, thereby improving algorithmic performance and collision avoidance.

The mortality of birds resulting from collisions and electrocutions with overhead lines, such as power lines, and phone line among others, has been implicated in the decline of various avian species globally. Specifically, overhead line collisions pose a significant threat to the conserva-tion of the Canarian houbara bustard (Chlamydotis undulata fuertaventurae), an endangered sub-species endemic to the Canary Islands. This study centres on the postmortem findings of Canarian houbara bustards that have collided with overhead lines, providing insights into the post-collision outcomes for these birds. A com-plete standardized necropsy of nine Canarian houbara bustards revealed that polytrauma was the cause of death in all cases. The most notable gross lesions associated with trauma included bone fractures, soft tissue lacerations, haemorrhages, luxations, and hemocoelom, with certain body regions being more frequently affected. Histopathology, immunohistochemistry, and en-tomology analysis confirmed that numerous birds survived the initial trauma, exhibiting varia-ble survival intervals before succumbing to their injuries. We concluded that when a houbara bustard collide with an overhead line it frequently survives the initial trauma. The histopathology, immunohistochemistry, or entomologic analysis may be helpful to approximate the timing interval between trauma and death.

The analysis of chemical warfare agents and their degradation products has become increasingly important for public and military safety in recent years. In the article, we drew attention to the possibilities of the HPLC-ICP-MS analytical technique, which has been relatively rarely used for identifying and quantitatively analyzing highly toxic and hazardous substances in environmental samples. This technique enables the identification and determination of minimal amounts (ppt range) of chemicals in various matrices. This fact is important for the analysis of chemical warfare agents and other highly harmful compounds, even small amounts of which can have serious consequences for living organisms. The article critically analyzes the results of scientific research on the identification and quantitative analysis of extremely toxic organophosphorus, organosulfur and organoarsenic substances, their derivatives and degradation products using high-performance liquid chromatography (HPLC) coupled with inductively coupled plasma mass spectrometry (ICP-MS).

Increasing concerns on animal welfare in commercial pig industry include aggression between pigs as it affects their health and growth. Early detection of aggressive behaviors is essential for optimizing their living environment. A major challenge for detection is that these behaviors are observed occasionally in normal conditions. Under this circumstance, a limited amount of aggressive behavior data will lead to class imbalance issue, making it difficult to develop an effective classification model for the detection of aggressive behaviors. To overcome this problem, we approach the aggressive behavior detection problem as a case of anomaly detection rather than classification and propose a model based on anomaly detection, which can better handle unbalanced class distribution and effectively detect the infrequent, aggressive episodes of pigs. The model consists of a convolutional neural network (CNN) and a variational long short-term memory (LSTM) autoencoder. Additionally, we adopted a training method similar to weakly supervised anomaly detection and included a few aggressive behavior data in the training set for prior learning. To effectively utilize the aggressive behavior data, we created Reconstruction Loss Inversion, a novel objective function, to train the autoencoder-based model to increase the reconstruction error of aggressive behaviors by inverting the loss function. Our anomaly detection approach significantly outperforms traditional classification-based methods, effectively identifying aggressive behaviors in a natural farming environment. This method offers a robust solution for detecting aggressive animal behaviors and contributes to improving their welfare.

Aluminum (Al) toxicity and low phosphorus availability (LP) are the top two co-existing edaphic constraints limiting agriculture productivity in acid soils. Plants have evolved versatile mechanisms to cope with the two stresses alone or simultaneously. However, the specific and common molecular mechanisms, especially those on flavonoids and carbohydrate metabolism, are still unclear. Laboratory studies were conducted on two wheat genotypes, Fielder (Al-tolerant and P-efficient) and Ardito (Al-sensitive and P-inefficient), exposed to 50 μM Al and 2 μM Pi (LP) in hydroponic solutions. After 4 days of stress, wheat roots were analyzed via transcriptomic and targeted metabolomic techniques. A total of 2296 differentially expressed genes (DEGs, 1535 up and 761 down) under Al and 3029 DEGs (1591 up and 1438 down) under LP were identified in Fielder. Similarly, 4404 DEGs (3191 up and 1213 down) under Al and 1430 DEGs (1176 up and 254 down) under LP were identified in Ardito. The GO annotation analysis results that 4079 DEGs annotated to the metabolic processes term. These DEGs were significantly enriched in the phenylpropanoid, flavonoid, flavone and flavonol biosynthesis, and carbohydrate metabolism pathways by performing the KEGG enrichment analysis. The targeted metabolome analysis detected 19 flavonoids and 15 carbohydrate components in Fielder and Ardito under Al and LP. More responsive genes and metabolites were involved in flavonoid metabolism under LP than Al in the Fielder, while an opposite trend in the Ardito. In the carbohydrate metabolism pathway, the genes and metabolites were higher in Fielder than in Ardito. The combined transcriptome and metabolome analysis revealed that the flavonoid and carbohydrate genes and metabolites differed between Fielder and Ardito under Al and LP, which may be an important reason for Fielder’s high Al and LP resistance. The results of this study lay a foundation for pyramiding genes and breeding multi-resistance varieties.

The number of people owning vehicles has been steadily growing, resulting in increased numbers of vehicles on the roads, making roads more congested, and increasing the risk of accidents. In addition, heavy rain, snow, and fog have increased due to abnormal weather caused by global warming. These bad weather conditions can also affect the safety of vehicles and drivers. The need to disseminate safety messages on the social internet of vehicles due to these problems has been steadily increasing. In this paper, we propose an efficient safety message dissemination scheme that focuses on urban environments with high vehicle density and mobility to address these problems. The proposed scheme reduces packet loss by considering frequent cluster departures and subscriptions through an efficient cluster management technique. In a vehicle-to-vehicle environment, the dissemination of safety messages is divided into an intra-cluster and an inter-cluster emergency as well as general safety message dissemination technique. In a vehicle to infrastructure environment, the proposed scheme reduces the number of processing requests and duplicate messages made to roadside units (RSUs) through a request operation process for each vehicle and an RSU scheduling technique. We conducted several performance evaluations of message packet loss and the number of RSU processing requests to demonstrate the superiority of the proposed scheme.

Fe-(9, 19, 28, 37)wt.% Cr alloys were corroded at 700 and 800 ^oC for 70 h under 1 atm of N₂, 1 atm of N₂/3.2%H₂O-mixed gas, and 1 atm of N₂/3.1%H₂O/2.42%H₂S-mixed gas. The corrosion rate of Fe-9Cr alloy increased with the addition of H₂O, and furthermore with the addition of H₂S in N₂ gas. Fe-9Cr alloy was always nonprotective. In contrast, Fe-(19, 28, 37) wt.%Cr alloys were protective in N₂ and N₂/H₂O-mixed gas because of formation of the Cr₂O₃ layer. They were, however, nonprotective in N₂/H₂O/H₂S-mixed gas because sulfidation dominated to form the outer FeS layer and the inner Cr₂S₃ layer containing some FeCr₂S₄.

This research aimed to study and compare prevalence of work-related musculoskeletal (MSK) problem and perceived discomfort among port crane operators consisting of quay and rubber tyred gantry (RTG) cranes working in the Laem Chabang Deep-sea Port, Thailand. Direct interviews for a cross-sectional analysis was selected for this unique job with a small amount of sample size. A standardized modified version of the Nordic Musculoskeletal Questionnaire (NMQ) was lunched for 26 male participants, consisting of 11 quay and 15 RTG, where a priori power analysis using G*Power suggested the minimum as 24 for the hypothesis test. Socio-demographic characteristics showed no significant difference among them. The NMQ revealed lower back as the highest prevalent body part (76.9%) followed by neck, shoulders and upper back at the same percentage (23.1%) for all port crane group, with up to 96.2% reporting MSK problem over the past 12 months. And Borg scale rating, assessing the perceived discomfort, revealed lower back with the highest score (2.38) followed by upper back (0.65), shoulders (0.54) and neck (0.5). Remarkably, the comparation between the quey and RTG crane operators on the MSK prevalence (χ2 test) and perceived discomfort levels (Kruskal-Wallis test), regarding different 9 body parts, revealed a significant difference between the two on upper back with quay crane having more problem than the RTG at p &lt; 0.05. while the rest of them were mainly in the same direction. MSK contributors such as: working awkward posture, mental stress, height, trolley distance and vibration are considerably the main causes of this. However, the larger in scale of exposure to those for the quey crane compared to the RTG might have led to the distinguishing MSK problem found in this study which require thoroughly deliberation for the particular solutions.

This study aimed to develop a state-of-the-art method for assessing chemical risks. The method combined desk research findings and the authors' practical knowledge to identify the major shortcomings in performing risk assessments at the workplace. Data were collected from nine SMEs across three sectors: agriculture, laboratory research, and conservation and restoration laboratories. The results of the discussions with the workers and on-site observations were used to develop the method to assess chemical risks. The method uses numerical factors to account for the level of conformity and the duration of exposure to support an estimation of the probability of an incident. The developed method was designed to enhance risk assessment practices and tackle common issues encountered by enterprises, including SMEs.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Dynamic virtual testing by Hardware in the Loop (HIL) real time simulation systems is common to minimize physical tests to validate and verify control algorithms, logics and software, under normal and emergency conditions. The accurate but costly HIL models setup activities could have an extended use to simulate faulty conditions that are seldom observable in the real system, yet they must be detected in advance and recognized. Data driven diagnostic methods have reached a mature development, in various sectors, proving effective in early detecting slowly varying deviations from nominal patterns of signals, even without a priori knowledge of their nature and behavior. These methods rely on vast amount of data logged from real systems that are ever and ever richer of monitoring telemetries that are worth being exploited. However, due to the usually reliable and safe systems being managed, it is often difficult to collect enough data on anomalous situations to validate fault detection and isolation and limit false positives. HIL model-based simulations allow generating and observing operational domains or transients rarely observed in real operations. This allows identifying the signals that are most correlated to faults and that could be selected to setup data-based diagnostic models of parts or subsystems, which are more suitable than the whole HIL model for online diagnostics, as well as to identify the features and trends that are most symptomatic of anomalous conditions.

The World Health Organization declared the coronavirus disease 2019 (COVID-19) pandemic in 2020, following which a global genetic vaccination program has been rapidly implemented as a fundamental solution. However, it has been reported worldwide that the modified mRNAs encoding spike proteins and lipid nanoparticles, which are used as drug delivery systems, not only cause thrombosis and cardiovascular disorders post vaccination, but might also cause diverse diseases involving all organs and systems, including the nervous system. Furthermore, the toxicity and pathogenicity of spike proteins may necessitate defining these proteins as nonbiological infective material. Based on these reports and the abundant evidence that has come to light in the past few years, this paper aims to draw the attention of medical professionals to the various risks associated with transfusion using blood products derived from long COVID patients or from genetic vaccine recipients, and to make proposals regarding specific inspection items, testing methods, regulations, etc. This paper provides insights to address the post-vaccination syndrome and its consequences following such genetic vaccination programs.

Distracted driving is a major cause of road traffic crashes in Yaoundé. Partly due to scarcity of enforcement, lack of evidence and investigation of distraction safety performance indicator (SPI), hindering evidence-based intervention. This study aimed to address this evidence gap by evaluating the distraction SPI using proven methodology. Data on distracted driving (handheld mobile device; interaction; eating/smoking/drinking) were collected from roadside observation on 36 randomly selected road sections carefully spread to cover the city. SPI were computed and weighted with traffic volume to ensure representativeness of values. A total of 41,004 drivers were observed (38,248 in car; 1,116 in van; 977 in truck; 663 in bus). The prevalence of distracted driving in Yaoundé is 13.69% for the three distractions type combined. The prevalence is 7.84% for interaction, 4.89% for handled mobile device usage and 0.96% for eating/smoking/drinking. Leveraging these insights, a seven year (2024 - 2030) fighting strategy aiming at halving the prevalence was developed. The strategy contains intervention including on legislation/enforcement, which have been proven effective. This study, pioneer in Yaoundé, provide stakeholders with evidence of the issue and measures to implement and can also serve when developing road safety strategy.Future research should consider investigation at national level.

In Yaoundé, Cameroon, excessive and inappropriate speeding remains a major public health concern. Part of the problem are the unsafe speed limits, lack of evidence, and effective evaluation of speeding safety performance indicators (SSPIs), and the absence of speed management, hindering the city's ability to mitigate the risks associated with speeding. This study aimed to address this knowledge gap by assessing SSPIs using a well-defined methodology and suggesting speed management strategies. Data on speed, traffic volumes and road attributes were collected from a random selection of 16 representative road sections in Yaoundé. Seven SSPIs were calculated, and weights were assigned to evaluate city-level SSPIs. The findings showed that 66.8% of drivers drive within the speed limit, generally operating at speeds of 54 km/h with a speed variation of 26 km/h. Based on the speed analysis, evidence-based strategies are proposed, and implementing these strategies could potentially reduce fatalities and serious injuries by 16% to 84% across study locations, as indicated by Elvik's model. These findings have significant policy implications for reducing speeding in Yaoundé, and the methodological approach can be replicated in other urban settings. Future research should extend SSPI evaluation to the national level and test the effectiveness of the recommended strategies.

Pedestrians, bicyclists, scooterists are Vulnerable Road Users (VRU) in traffic accidents. The number of fatalities and injuries in traffic accidents involving vulnerable road users has been steadily increasing in the last two decades in the U.S. even though road vehicles now have perception sensors like camera to detect risk and issue collision warnings or apply emergency braking. Perception sensors like camera are highly affected by lighting and weather conditions. Camera, radar and lidar cannot detect vulnerable road users in partially occluded and occluded situations. This paper proposes the use of Vehicle-to-VRU communication to inform nearby vehicles of VRUs having trajectories with potential collision risk. An Android smartphone app with low energy Bluetooth (BLE) advertising is developed and used for this communication. The same app is also used to collect motion data of VRUs for training. VRU motion data is smoothed using a Kalman filter and an LSTM neural network is used for future motion prediction. This information is used in an algorithm comparing Time-To-collision-Zone (TTZ) for the vehicle and VRU and issue a driver warning with different severity levels. The warning severity level is based on analysis of real data from a smart intersection for close vehicle and VRU interactions. The resulting driver warning system is demonstrated using proof-of-concept experiments. The method can easily be extended to a VRU collision mitigation system.

Exoskeleton technology has been shown to be useful for individuals with spinal cord injury (SCI), potentially facilitating their recovery of motor function and social reintegration. However, studies on the safety and usability of exoskeletons are limited. This study aimed to design a powered exoskeleton for SCI and evaluate its safety and usability. Ten healthy adults participated in this study. The prototype exoskeleton featured an adjustable frame, computer-controlled hip and knee joint actuators, and a gait-trigger sensor. The experimental actions included walking, standing, and sitting, with and without the prototype. Safety outcomes included adverse events, vital signs, numerical rating scale (NRS) scores for pain, discomfort, and fatigue, and prototype-human body clearance. Usability outcomes included donning and doffing times, subjective ratings, gait speed, stride length, and kinematic parameters of hip and knee joint angles. Safety outcomes showed no serious adverse events, stable vital signs, minimal NRS scores, and acceptable clearance. Usability outcomes showed high efficiency and received positive ratings. Kinematic parameters showed significant positive correlations between normal walking and walking with the prototype for both hip and knee joint angles, confirming its effectiveness in assisting walking. However, further device improvements and gait parameter tuning are necessary for future clinical application.

Redox mediators comprising I–, Co3+, and Ti3C2Tx MXene were applied to dye-sensitized solar cells (DSCs). In the as-prepared DSCs (I-DSCs), wherein hole conduction occurred via the redox reaction of I−/I3− ions, the power conversion efficiency (PCE) was not altered by the addition of Ti3C2Tx MXene. The I-DSCs were exposed to light to produce Co2+/Co3+-based cells (Co-DSCs), wherein the holes were transferred via the redox reaction of Co2+/Co3+ ions. A PCE of 9.01% was achieved in a Co-DSC with Ti3C2Tx MXene (Ti3C2Tx-Co-DSC), which indicated an improvement from the PCE of a bare Co-DSC without Ti3C2Tx MXene (7.27%). It was also found that the presence of Ti3C2Tx MXene in the redox mediator increased the hole collection, dye regeneration, and electron injection efficiencies of the Ti3C2Tx-Co-DSC, leading to an improvement in both the short-circuit current and the PCE when compared with those of the bare Co-DSC without MXene.

The relationship between the structure characteristics and performances of coal based hydrogenation isomeric base oil (CTL) and metallocene catalyzed coal based polyalphaolefin (mPAO) base oil was clarified here. CTL and mPAO were compared with typical petroleum based and natural gas based commercial API Class III and IV base oils. Pressurized differential scanning calorimetry (PDSC), Rotary Bomb Oxidation Test (RBOT) and four-balls friction tester were used to evaluate the oxidation stability and lubrication performance of base oils under different working conditions. The sensitivity of different base oils to typical antioxidants and extreme pressure antiwear agents was compared. Specially, the composition and structure of CTL base oil are obviously different from GTL and mineral base oil. The coal-based CTL and mPAO base oils exhibit commendable viscosity-temperature properties, characteristics, coupled with low-temperature fluidity, fire safety, and minimal evaporation loss. The lubricating properties, oxidation stability and the sensitivity to extreme pressure antiwear agents of CTL are close to those of similar base oils. But the sensitivity of CTL to typical antioxidants is relatively poor. Besides, compared with commercial PAO base oil, mPAO has lower isomerization degree and fewer isomerization types. The oxidation stability and sensitivity to typical antioxidants of mPAO base oil are comparable with those of commercial PAO base oil, while its lubrication performance and sensitivity to typical extreme pressure antiwear agents are significantly better than those of commercial PAO base oil.

Myasthenia gravis (MG) is a disease characterized by typical clinical and immunopathogenic pe-culiarities, which correlate with age and sex/gender. Accordingly, MG patients show thymic al-terations and auto-antibodies productions, that can be the expression of a different pathogenetic mechanism related to age and gender. This determines, in relation to age at and sex/gender, a dif-ferent MG onset, prognosis, and outcome. Therefore, diverse MG forms can be identified, classi-fied, and characterized in relation to their different features, and precisely there are early onset and late-onset forms of MG. It has been hypothesized that the cause of appearance the two diverse forms of MG can be ascribed mainly to the diverse genetic and epigenetic factors. In this narrative review, we will analyze and discuss about the interplay of age- and sex-related factors (i.e. genet-ic and epigenetic factors) related to two different MG forms and how they contribute to their di-verse pathogenesis.

Tissue-like phantoms are widely used as a model for mimicking the optical properties of live tissue. This paper presents the results of a diffusion reflection method as well as fluorescence lifetime imaging microscopy measurements of fluorescein-conjugated gold nanorods in solution as well as inserted in solid tissue-imitating phantoms. A lack of consistency between the fluorescence lifetime results of the solutions and the phantoms raises a question about the ability of tissue-like phantoms to maintain the optical properties of inserted contrast agents.

Bacteriophages (phages) are potential alternatives to chemical antimicrobials against pathogens of public health significance. Understanding the diversity and host specificity of phages is important for developing effective phage biocontrol approaches. Here, we assessed the host range, morphology, and genetic diversity of eight Salmonella enterica phages isolated from a wastewater treatment plant. The host range analysis revealed that six out of eight phages lysed more than 81% of the 43 Salmonella enterica isolates tested. The genomic sequences of all phages were determined. Whole genome sequencing data (WGS) data revealed that phage genome sizes ranged from 41 to 114 kb with GC contents be-tween 39.9 and 50.0 %. Two of the phages SB13 and SB28 represent new species Epsep-timavirus SB13 and genera Macdonaldcampvirus, respectively as designated by the In-ternational Committee for the Taxonomy of Viruses (ICTV) as per genome based taxonomic classification. One phage (SB18) belonged to the Myoviridae morphotype while the re-maining phages belonged to the Siphoviridae morphotype. The gene content analyses showed that none of the phages possessed virulence, toxin, antibiotic resistance, type I-VI toxin-antitoxin modules or lysogeny genes. Three (SB3, SB15 and SB18) out of the eight phages possessed tailspike proteins. Whole genome-based phylogeny of the eight phages with their 113 homologs revealed three clusters A, B, C and seven subclusters (A1, A2, A3, B1, B2, C1 and C2). While cluster C1 phages were predominantly isolated from animal sources, cluster B contained phages from both wastewater and animal sources. The broad host range of these phages highlights their potential use to control the presence of S. enterica in foods.

The mechanisms underlying the establishment of asymmetric structures during development remain elusive. The wing of Drosophila is asymmetric along the Anterior-Posterior (AP) axis, despite that its growth signals that drive its growth are presumably symmetric. Here, we investigated the contribution of cell recruitment, a process that drives wing fate differentiation in Drosophila, to the asymmetric shape and pattern of the adult wing. Genetic impairment of cell recruitment results in a significant reduction in adult wing asymmetry, primarily affecting the region between longitudinal vein 5 and the wing margin (L5-M). Morphometric analysis reveals that the lack of cell recruitment results in a more symmetric wing with respect to the AP, suggesting a contribution of cell recruitment to the establishment of asymmetry in the adult wing. A close examination of the expression of the wing selector gene vestigial (vg) in wing disc does not support this hypothesis. However, the circularity of the Vg pattern significantly increase in recruitment-impaired wing disc, suggesting that while the decrease of the L5-M region in the adult wing may not be attributed to cell recruitment, it could contribute to the overall asymmetry of the adult wing. We conclude that cell recruitment, a widespread mechanism that participates in growth and patterning of several developing systems, could drive, at least partially, the asymmetric shape of the Drosophila wing.

The software design of autonomous vehicles (AVs) incorporates artificial intelligence (AI) characteristics to enhance their safety and overall driving performance. Central to vehicle’s operation is the ability to reason effectively in complex and uncertain environments. However, traditional logical systems, such as monotonic logic, often struggle to handle the inherent uncertainties and exceptions encountered in real-world scenarios. This paper proposes the utilization of non-monotonic logic in order to enhance the reasoning capabilities of autonomous vehicles. By incorporating non-monotonic reasoning, vehicles can navigate intricate traffic scenarios, make plausible inferences, and adapt their decisions when faced with conflicting information. This research aims to provide a comprehensive review of non-monotonic logic's application in autonomous vehicles, highlighting its advantages over traditional logical systems and its potential impact on safety and performance. Additionally, through this research, we seek to contribute to the advancement of autonomous driving technology by enhancing the reasoning capabilities of vehicles in various scenarios, such as car- following related to critical safety events. The personalized cognitive agent is proposed in driving behavior to consider particularly in their assumptions of homogeneous drivers. The personalized cognitive agent is incorporating heterogeneous driving behaviors, based on individual user preferences, characteristics, and needs. Driving behavior is a complex interplay of various factors, encompassing both human and external elements. Human factors, including age, experience, and gender, contribute significantly to how individuals navigate the roads. These factors influence decisions, reactions, and risk-taking tendencies on the part of drivers. Additionally, external factors such as weather conditions further compound this intricate dynamic, requiring drivers to adapt their behavior to the prevailing environment. The goal of a personalized cognitive agent is to provide tailored and customized experiences to cognitive vehicles, taking into account the unique requirements and individual preferences of occupants inside autonomous vehicles.

(1) Background: The study of microbiome is being crucial for his role in major systemic diseases, in particular the oral and gut microbiota. In the last years the study of microorganism correlated for example with neurodegenerative disease is increasing the prospective of a possible link between gut microbiota and brain. Here we report a new case report about a patient evaluated genetically firstly for dementia and late-onset dyskinesia, and then tested with 16S metagenomics sequencing. (2) Methods: Starting from buccal swab, we extracted bacterial DNA and then we performed a NGS metagenomics sequencing based on the amplification of hypervariable regions of the 16S in bacteria. (3) Results: The sequencing revealed the presence of Spirochaetes Phylum, a pathogenic bacterium generally known to be able to migrate to the Central Nervous System and not only. (4) Conclusions: Oral infections as our results shows could be possible contributing factors to various neurodegenerative conditions.

Driven by the growing interest of the scientific community and the proliferation of research in this field, cranial implants have seen significant advancements in recent years regarding design techniques, structural optimisation, appropriate material selection and fixation system method. Custom implants not only enhance aesthetics and functionality but are also crucial for achieving proper biological integration and optimal blood irrigation, critical aspects in bone regeneration and tissue health. This research aims to optimize the properties of implants designed from triply periodic minimal surface structures. The gyroid architecture is employed for its balance between mechanical and biological properties. Experimental samples were designed varying three parameters of the surface model: cell size, isovalue and shape factor. Computational simulation tools were used for determining the relationship between those parameters and the response variables: the surface area, permeability, porosity and Young modulus. These tools include computer aided design, finite element method and computational fluid dynamics. With the simulated values, the corresponding regression models were fitted. Using the NSGA-II, a multi-objective optimisation was carried out, finding the Pareto set which includes surface area and permeability as targets, and fulfil the constraints related with the porosity and Young modulus. From these non-dominated solutions, the most convenient for a given application was chosen, and an optimal implant was designed, from a patient computed tomography scan. An implant prototype was additively manufactured for validating the proposed approach.

This paper presents a comprehensive study on the application and optimization of automotive thermoelectric generators (ATEGs), focusing on the crucial role of heat exchangers in enhancing energy conversion efficiency. Recognizing the substantial waste of thermal energy in internal combustion engines, our research delves into the potential of TEGs to convert engine waste heat into electrical energy, thereby improving fuel efficiency and reducing environmental impact. We meticulously analyze various heat exchanger designs, assessing their influence on the TEG's output power under different exhaust gas flow rates and temperatures. Furthermore, we explore the impact of TEG material properties on the overall energy conversion effectiveness. Our findings reveal that specific heat exchanger designs significantly enhance the efficiency of waste gas heat exchange, leading to an improved performance of the TEG system. We also highlight the importance of thermal insulation in maximizing TEG output. This study not only contributes to the ongoing efforts to develop more sustainable and efficient vehicles but also provides valuable insights into the practical application of thermoelectric technology in automotive engineering. Through this research, we aim to pave the way for more environmentally friendly transportation solutions, aligning with global efforts to reduce fossil fuel dependence and mitigate environmental pollution.

Background: The front-line treatment of advanced NeuroEndocrine Neoplasms (NENs) depends on clinical and pathological factors but there are no standard second-line therapies. Methods: Metastatic NENs patients were treated at the ENETS (European NeuroEndocrine Tumor Society) center of excellence of Naples (Italy), from 2014 to 2017 with second-line metronomic temozolomide, 75 mg/m2 per os “one week on/one week off”. Toxicity was graded with NCI-CTC criteria v4.0; objective responses with RECIST v1.1 and performance status (PS) according to ECOG. Results: Twenty-six consecutive patients were treated. Median age was 65.5 years. The predominant primary organs were pancreas and lung. Grading was G2 in 11 patients, G3 in 15. Eleven patients presented with PS 1 and 15 with PS 2. The median time-on-temozolomide therapy was 12.2 months (95% CI: 11.4-19.6). No G3/G4 toxicities were registered. Complete response was obtained in 1 patient, partial response in 4, stable disease in 19 (disease control rate: 92.3%), and progressive disease in 2. The median overall survival from temozolomide start was 28.3 months. PS improved in 73% of patients. Conclusions: Metronomic temozolomide is a safe and active treatment for G2 and G3 NENs. Prospective and larger trials are needed to confirm these results.

Studying models of healthy aging and exceptional longevity is crucial to understand a possible longevity signature as most of them show resistance to age-related diseases. In particular, semi- and supercentenarians are a highly selected group, having survived significant adversities, including the Spanish Flu and COVID-19 pandemics, indicating distinctive immune system characteristics. This paper analyse the inflammatory scores (INFLA-score, Systemic Inflammation Response Index (SIRI)) and Aging-Related Immune Phenotype (ARIP) indicators calculated from the dataset of the DESIGN project, including 249 participants aged 19-111 years, trying to understand the immune-inflammatory (IMFLAM) role to achieve longevity. Statistical analyses, including linear regression and one-way ANOVA, were performed to explore the correlations between these parameters and age. Both INFLA-score and SIRI showed a significant increase with age. However, no statistical difference is observed when analysing the values for semi- and supercentenarians with those for other age groups, whose values are similar to that of adults and less than younger centenariansRegarding ARIP values, it is noteworthy that when comparing the CD8 Naive/Effector scores between groups, no significant differences were observed between the semi- and supercentenarian group and the other groups. These results support the idea that the control of IMFLAM response can promote extreme longevity.

Sea cucumber peptides are small molecular peptides with biological function obtained from fresh sea cucumber as feedstock, which were hydrolyzed by protease, separated ,and purified. As the main product of sea cucumber refinement, it more accurately expresses the nutritional effect of sea cucumber and has a wide range of potential applications. It has been demonstrated that sea cucumber has a certain value-added effect on bone mineral density regulation, but the differences in bone mineral density regulation of extracts from different parts of sea cucumber and the techniques contributing to the efficient isolation of bone sea cucumber peptides have not been reported. Firstly, the aim of this study was to reveal the differences in osteogenic activities of enzymatic peptides from three major parts of sea cucumber: the body wall, the egg protein, and the intestinal protein. Then, the bone-enhancing sea cucumber peptides were isolated based on the characteristics of the dif-ferences in molecular weight distribution, hydrophilicity, and ionisation degree of sea cucumber, and to explore the possible mechanisms of their action. The findings indicated that sea cucumber peptides extracted from three distinct sites exhibited a dose-dependent enhancement of osteoblast proliferation and differentiation. Upon evaluating the three methods of sea cucumber peptide separation based on molecular weight distribution, hydrophilicity, and ionization, it was observed that the fraction isolated by hydrophobicity and

Extremely low-frequency electromagnetic fields (ELF-EMF) are ubiquitous in industrial-11 ized environments due to the continuous use of electrical devices. Our previous studies demon-12 strated ELF-EMF affects muscle cells by modulating oxidative stress and enhancing myo-genesis. 13 This pilot study investigated these effects on skeletal muscles of sedentary adult mice, assessing 14 physiological responses to ELF-EMF exposure and potential modulation by antioxidant supplemen-15 tation. Male C57BL/6 mice were exposed to ELF-EMF (0.1 or 1.0 mT) 1 hour/day up to 5 weeks, and 16 fed a standard diet without or with N-acetyl-cysteine (NAC). Results showed transient increases in 17 muscle strength (after 2-weeks’ exposure at 1.0 mT), potentially linked to muscle fiber recruitment 18 and activation, revealed by higher PAX7 and MyH expression levels. After ELF-EMF exposure, ox-19 idative status assessment revealed transient increases in expression levels of SOD1 and catalase en-20 zymes, in total antioxidant capacity and in protein carbonyl levels, marker of oxidative damage. 21 These effects were partially reduced by NAC. In conclusion, ELF-EMF exposure affects skeletal 22 muscle physiology and NAC supplementation partially mitigates these effects, highlighting the 23 complex interactions between ELF-EMF and antioxidant pathways in vivo. Further investigations 24 on ELF-EMF as a therapeutic modality for muscle health are necessary.

The paper provides and comments on the results of studies of the effect of sandstone-based abrasives and quartz sand alone on the wear of martensitic surfaces of wear-resistant steels. The wear process was examined on a ring-on-ring test rig seeking to determine the mass decrement parameter which characterised wear. The tests were conducted for three sandstone varieties: Carboniferous, Permian, and Cretaceous, and they made it possible to determine that the most intense process of deterioration of wear-resistant steels took place in the presence of quartz sand grain, while less intense wear was observed in the case of sandstone-based abrasives. The mass decrement values established in the presence of the sandstones in question did not differ significantly between individual sandstone varieties. Based on a surface damage analysis, the basic damage mechanism was found to be micro-scratching, however, with regard to the sandstones examined, it was also determined that individual grains could be pressed into surface irregularities, as well as that films of soft hematite cement developed in the Permian sandstone and that inclusions of carbonaceous matter were formed in the Carboniferous sandstone. With reference to the wear process observations, a wear model was described for the surface of the steels examined in the presence of sandstone-based abrasives.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Safety and the apprehension of crime persist as significant concerns in both urban and rural locales. Crime Prevention Through Environmental Design (CPTED) guidelines, an architectural approach to crime deterrence, mitigate the likelihood of criminal activity by implementing strategic defensive design plans, particularly through effective lighting schemes within urban settings, thereby alleviating fear of crime. This comprehensive set of principles serves to enhance overall quality of life. Additionally, within the realm of environmental crime prevention, enhanced street lighting has been identified as a crucial factor in diminishing both actual crime rates and the perceived risk of criminal activity in built environments. While current recommendations advocate for the installation of lighting in poorly lit areas for safety reasons, evaluating visibility solely based on the presence of existing streetlights proves insufficient for analyzing road surface luminance comprehensively. Thus, this study proposes establishing standardized illumination levels specifically tailored for facial recognition of potential criminal offenders. Furthermore, we advocate for defining specific thresholds for color temperature and colorimetric criteria to aid in distinguishing characteristics of individuals' attire. To analyze photometric safety and crime frequency in Seoul, Korea, new primary evaluation indicators were developed, including the Brightness index, Informatization index, and Safety index. By incorporating quantitative data into lighting design strategies, particularly within the framework of CPTED, there exists the potential to mitigate fear of crime during nighttime hours. These strategies facilitate the creation of well-lit environments conducive to the swift recognition and identification of potential perpetrators, thereby presenting a proactive approach to crime prevention. Consequently, this study introduces quantitative lighting standards to augment the efficacy of CPTED guidelines, ultimately contributing to the reduction of crime incidence.

Bi1-xSbx crystal is one of the best n-type thermoelectric materials below 200 K, but its weak mechanical strength hinders practical applications for deep refrigeration. Herein, we adopted the mechanical enhancement method of hot extrusion to investigate the comprehensive mechanical and thermoelectric properties of Bi0.905Sb0.095. It revealed that reducing the grain size of the matrix and increasing the extrusion ratio can improve the gain size uniformity and mechanical properties. While the thermoelectric performance depends on the texture, grain size, and local composition. The extruded sample prepared by ingot with the high extrusion ratio of 9:1 generated a high texture degree of (001) plane and small grain sizes between ~4-40 mm, which resulted in the high bending strength of Bi1-xSbx ~130 Mpa and a high-power factor of ~ 68 μW·cm-1·K-2@173 K, as well as the relative high figure of merit of 0.25@173K. This work highlights the importance of the uniform distribution of the grain size and the compositions for Bi1-xSbx, as well as the required universal key parameter for the hot-extrusion method.

To obtain carbon dots (CDs) with narrow full width at half maximum (FWHM) and long-wavelength emission, carbon sources with high conjugate sizes and abundant functional groups can be employed to synthesis CDs. In this study, orange-emissive carbon dots (OCDs) were synthesized with phloroglucinol and rhodamine B as precursors. When the molar ratio of them was 30:1 and ethanol was served as solvent, OCDs with optimized emission wavelength at approximately 580 nm, an FWHM of 30 nm and a quantum yield (QY) of 27.31% were obtained. Subsequently, the OCDs were incorporated into polyvinyl alcohol (PVA) to fabricate solid-state OCDs/PVA fluorescent films, which exhibited an FWHM of 47 nm. The PVA matrix facilitated the dispersion of OCDs, thereby suppressing non-radiative energy transfer among the OCDs and enhancing luminescence efficiency. Consequently, compared with OCDs, the OCDs/PVA film exhibited significant luminescent enhancement, and the QY of the composite film was increased to 84.74%. Moreover, OCDs/PVA film show good transmittance and thermal stability. This research offers a solid theoretical and experimental foundation for the potential applications of CDs in the fields of solid-state lighting.

The objective of this study is to investigate the aquatic-toxic effects of glyoxal-containing cellulose ether with four different glyoxal concentrations (0, 1.4, 2.3 and 6.3%) in response to global chemical regulations, e.g., European Union Classification, Labeling and Packaging (EU CLP). Tests of the aquatic-toxic effects of glyoxal-containing cellulose ether on 11 freeze-dried microbial strains, Microcystis aeruginosa, Daphnia magna and zebrafish embryos were designed as an initial stage for toxicity screening, and were performed with the standardized toxicity test guidelines. Glyoxal-containing cellulose ether showed no significant toxic effects in the toxicity tests for the 11 freeze-dried microbial strains, Daphnia magna and zebrafish embryos. Alternatively, 6.3% glyoxal-containing cellulose ether led to more than a 60% reduction of Microcystis aeruginosa growth after 7 days of exposure. Approximately 10% developmental abnormalities (e.g., bent spine) in zebrafish embryos were also observed in the group exposed to 6.3% glyoxal-containing cellulose ether after 6 days of exposure. These results imply that <6.3% glyoxal-containing cellulose ether results in non-toxic effects on the acute toxicity of aquatic organisms. However, ≥6.3% glyoxal-containing cellulose ether may affect the health of aquatic organisms with long-term exposure. In order to better evaluate the eco-safety of cellulosic products contained in glyoxal, further studies regarding the toxic effects of glyoxal-containing cellulose ether with long-term exposure are required. The results from this study allow us to evaluate the auatic-toxic effects of glyoxal-containing cellulosic products, under EU chemical regulations, on the health of aquatic organisms.

The development of accurate dynamic battery pack models for electric vehicles (EVs) is critical for the ongoing electrification of the global automotive vehicle fleet, since these serve as a key element in the energy performance of an EV powertrain system. The Equivalent Circuit Model (ECM) technique at the cell level is commonly employed for this purpose, combining accuracy and efficiency in the representation of battery operation within the broader powertrain system. In this study, a second-order ECM model of a battery cell is being developed using Modelica, an equation-based modeling language. Parameter lookup tables at multiple levels of state of charge (SoC), extracted from Li-ion battery cells with 4 different commonly used cathode materials, have been utilized. This approach allows for a representation of the battery systems that are used in a wide range of commercial EV applications. To verify the model, an integrated EV model is developed and simulation results of the FTP75 driving cycle have been compared against an equivalent application in MATLAB Simulink. The findings demonstrate a close match between the results obtained from both software across different system points. Specifically, the maximum deviation of SoC is limited to 0.08% and the maximum value of relative voltage deviation is 1.4%. The verified model enables the exploration of multiple possible architecture configurations of EV powertrains with Modelica.

The invasion of ship domain stands out as a significant factor contributing to the risk of collisions during vessel navigation. However, there is a lack of research on the mechanisms underlying collision risks specifically related to merchant and fishing vessels in coastal waters. This study proposes an assessment method for collision risks between merchant and fishing vessels in coastal waters and validated through a comparative analysis through visualization. First of all, the operational status of fishing vessels is identified. Collaboratively working fishing vessels are treated as a unified entity, expanding their ship domain during operation to assess collision risks. Secondly, to quantify the collision risk between ships, a collision risk index (CRI) is proposed and visualized based on the severity of collision risk. Finally, taking the high risk area of merchant and fishing vessels collision in the Minjiang River Estuary as an example, this paper conduct the analysis involves classifying ship collision scenarios, extracting risk data under different collision scenarios, and visually analyzing areas prone to danger. The results indicate that this method effectively evaluates the severity of collision risk, and the identified high-risk areas resulting from the analysis is verified by accidents occurred in the recent three years.

Exposure to cadmium sulfate (CdSO4) can lead to neurotoxicity. Nevertheless, the precise molec-ular mechanisms underlying this phenomenon remain unclear, and effective treatment strategies are scarce. This study explored the protective effects of ellagic acid (EA), a natural polyphenolic compound, against CdSO4 exposure-induced neurotoxicity in HT22 cells. Additionally, the inves-tigation sought to elucidate the molecular mechanisms underlying this phenomenon. Our findings demonstrated that exposure of HT22 cells to CdSO4 resulted in apoptosis, which was effectively reversed by EA supplementation. EA supplementation also decreased reactive oxygen species (ROS) and mitochondrial ROS productions, reduced malondialdehyde (MDA) levels, and restored the activities of superoxide dismutase (SOD) and catalase (CAT). Additionally, EA supplementation at 5–20 μM significantly counteracted Cd-induced mitochondrial membrane potential and ATP losses and reduced the ratio of Bax/Bcl-2 and cleaved-caspase-3 protein expression. Furthermore, EA supplementation upregulated Nrf2 and HO-1 protein expression while downregulating the phosphorylation of JNK and p38 proteins. Pharmacological inhibition of JNK partially inhibited CdSO4-induced Nrf2/HO-1 activation and exacerbated its cytotoxicity. In conclusion, our results indicate that EA supplementation provides protection against CdSO4-induced cell apoptosis in HT22 cells by inhibiting oxidative stress and activating the Nrf2 pathway. Activation of the JNK pathway plays a protective role in CdSO4-induced cell apoptosis in HT22 cells.

The Indian meal moth, Plodia interpunctella, poses a significant threat to global agricultural products. Although pheromone-based technologies show promise for P. interpunctella management, limitations like single-sex targeting necessitate exploring complementary strategies. Vegetable-based oils represent a potential alternative, but their efficacy, sex-specificity, and interaction with sex pheromones remain unclear. To answer these questions, we first examined attraction of P. interpunctella female and male adults to ten different vegetable oils, i.e., camellia, corn, olive, peanut, rapeseed, sesame, soybean, sunflower, walnut, and a blended oil (mixture of sunflower seed, rapeseed, soybean, peanut, and sesame oils), in the semi-field conditions. Sesame, olive, and blended oils demonstrated most attractive, capturing significantly more adults compared to other oils. We then evaluated effectiveness of these three attractive oils and their combinations with P. interpunctella sex pheromone in a grain warehouse. Traps baited with these oils captured significantly more females and males compared to control traps without attractants. However, sex pheromone addition did not improve male capture and significantly reduced female capture, suggesting an inhibitory effect. Our findings highlight the potential of blended, olive, or sesame oil trap alone as alternative monitoring and trapping tools for P. interpunctella, delivering novel insights into the development of efficient integrated pest management strategies for stored products.

In this work, we designed a MEMS device which allows simultaneous direct measurement of mechanical properties during deformation under external stress and characterization of the evolution of microstructure of nanomaterials within a transmission electron microscope. This MEMS device makes it easy to establish the correlation between microstructure and mechanical properties of nanomaterials. The device uses piezoresistive sensors to qualitatively measure the force and displacement of nanomaterials, e.g., in wire and thin plate forms. The device has a theoretical displacement resolution of 0.19 nm and a force resolution of 2.1 μN. The device has a theoretical displacement range limit of 2.74 μm and a load range limit of 27.75 mN.

Pipeline conflicts arising from data dependencies are a common issue encountered in the hardware implementation of layered QC-LDPC decoders. This paper proposes an efficient layered decoding architecture to reduce pipeline conflicts without introducing stall cycles, by reordering the processing order offline and using the patch method based on variable-to-check message. The experimental results on the LDPC code of the IEEE802.16 standard in the OFDM-PON system demonstrate that the proposed architecture has a sensitivity improvement of 0.125 dBm and 0.375 dBm, respectively, compared with our previous work and the method described in the other work.

The agonist-antagonist myoneural interface (AMI), a surgical method to reinnervate physiologically-relevant proprioceptive feedback for control of limb prostheses, has demonstrated the ability to provide natural afferent sensations for limb amputees when actuating their prostheses. Following an AMI surgery, one potential challenge is atrophy of the disused muscles, which would weaken the reinnervation efficacy of AMI. It is well known that electrical muscle stimulus (EMS) can reduce the muscle atrophy. In this study, we conducted an animal investigation to explore whether the EMS can significantly improve the electrophysiological performance of AMI. The AMI surgery was performed in 14 rats, in which the distal tendons of bilateral solei donors were connected and positioned on the surface of the left biceps femoris. Subsequently, the left tibial nerve and the common peroneus nerve were sutured onto the ends of the connected donor solei. Two stimulation electrodes were affixed onto the ends of the donor solei for EMS delivery. The AMI rats were randomly divided into two groups. One group regularly received the EMS treatment (designated as EMS_on) for eight weeks and another was no EMS (designated as EMS_off). Two physiological parameters, nerve conduction velocity (NCV) and motor unit number, were derived from the electrically evoked compound action potential (CAP) signals to assess the electrophysiological performance of AMI. Our experimental results demonstrated that the reinnervated muscles of the EMS_on group generated higher CAP signals in comparison to the EMS_off group. Both NCV and motor unit number were significantly elevated in the EMS_on group. Moreover, the EMS_on group displayed statistically higher CAP signals on the indirectly activated proprioceptive afferents than the EMS_off group. These findings may suggested that the EMS treatment would be promise in enhancing the electrophysiological performance and facilitating the reinnervation process of AMI.

The global increase in population has placed significant pressure on food security, leading to the emergence of aquaculture as a vital source of aquatic foods. However, rising costs and the limited availability of fishmeal in aquafeeds have spurred the search for alternative protein sources. While plant-based ingredients have been integrated into commercial aquafeeds, they come with challenges, including low protein content, palatability issues, and the presence of antinutritional factors. In this context, fish silage, derived from fish waste and discarded fish, stands out as a promising alternative technology due to its cost-effectiveness and sustainability attributes. The production of fish silage involves the addition of organic/inorganic acids or lactic acid bacteria to homogenized fish waste. This process yields a valuable mixture rich in peptides, free amino acids, and partially hydrolyzed proteins, offering significant nutritional benefits for animal diets. Beyond its nutritional advantages, fish silage contributes to environmental sustainability by reducing the impact of waste disposal and enhancing the value of fish waste. The objective of this review is to promote sustainable practices in the aquaculture industry in response to the increasing demand for high-quality feed nutrients. To achieve this, it includes an analysis of research results related to silage technology, an appraisal of the advantages and disadvantages of using fish silage as a feed additive, and a focus on emerging trends in this field.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

A novel determination method using flow-through cartridge purification and ultra-high-performance liquid chromatography coupled to tandem mass spectrometry (UPLC-MS/MS) was developed for the identification and quantification of 30 mycotoxins (aflatoxin B1, B2, G1, G2, sterigmatocysin, T-2 toxin, diacetoxyscirpenol, roquefortine C, methylergonovine, ergocornine, lysergol, enniatin A, enniatin A1, enniatin B, enniatin B1, beauvericin, deoxynivalenol, 3-acetylDeoxynivalenol, 15-acetylDeoxynivalenol, patulin, verruculogen, neosolaniol, gliotoxin, HT-2 toxin, wortmannin, zearalenone, α-zearalenol, β-zearalenol, α-zearalanol, and β-zearalanol) in feedstuffs. Mycotoxins were extracted from sample by 0.1% formic acid aqueous solution/acetonitrile (16/84 v/v), then purified by a Cleanert® MC clean-up column. As a result, the pigments and other matrices were efficient removed from the sample extract solution. The purified eluate was collected, then evaporated and redissolved by 0.1% formic acid aqueous solution/acetonitrile (70:30 v/v) for UPLC-MS/MS detection. A BEH Shield RP18 chromatographic column was employed for separation of 30 mycotoxins in a total of 14 min. Multiple-reaction monitoring (MRM) mode was applied for qualitative and quantitative analysis, and matrix calibration curves obtained with the external-standard method was used for quantitation of target analytes. Under optimized conditions, the linearity range was from 2 to 1000 ng/g, and the limit of quantification of the developed method was from 2 to 50 ng/g. The recoveries of 30 mycotoxins spiked in urine samples were from 72.0% to 118.5%, and the relative standard deviation was below 20%. The method was also well approved by certified reference sample, and applied on the real feedstuff samples testing successfully.

Quorum sensing (QS) is a sophisticated bacterial cell-to-cell communication mechanism that allows bacteria to sense population density through the secretion and detection of diffusible small molecular signals. This process leads to the coordinated expression of specific genes at the transcriptional level. Over time, continuous research has elucidated the genetic elements and regulatory principles of QS. Recently, synthetic biology has leveraged these insights to construct genetic circuits incorporating QS components, enabling both intra-species and inter-species artificial communication. These QS-based genetic circuits hold significant potential for applications in biotechnology and biomedicine. This paper reviews several well-characterized microbial QS systems and their functional roles, while also introducing the application of QS-based genetic circuits in cellular communication across species. The paper further discusses the role of QS in the development of biological computing tools, population density regulation, and metabolic flux control, offering a forward-looking perspective on future advancements. For intra-species communication, the focus is on the use of QS systems in constructing biological computing tools, including toggle switches, biosensors, and logic gates in synthetic biology. These tools, designed on the QS mechanism, can more precisely coordinate cellular behavior by integrating biological control circuits to achieve spatial, temporal, and population-level regulation. In the context of inter-species communication, the introduction of QS systems plays a pivotal role in population density control and metabolic flow regulation. By recombining metabolic networks, QS enables the redistribution of metabolic flux in desired pathways, facilitating the regulation of population density and the co-culture of mixed strains. Moreover, combining QS with oscillator models has shown great potential in synchronizing microbial communities. In summary, in-depth research into QS mechanisms and their applications not only lays a solid foundation for understanding microbial ecological competition and dynamic balance, but also offers promising avenues for regulating pathogenic bacteria and developing innovative disease control strategies.

The research was aimed at comparing the fire characteristics of different types of pepper in the context of designing explosion prevention. The following characteristics were studied: explosion pressure pmax and Kst at selected concentrations, ignition temperature of the deposited dust layer from the hot surface and minimum initiation energy. The comparison of the chemical properties of the used types of pepper was performed using TG/DSC. Results of the measurements suggest that different types of peppers exhibit different explosion characteristics. Each of the samples reached the maximum value of the explosion pressure, and their rate of pressure rise increased at different concentrations. The volume of the explosion chamber used also influenced the explosion characteristics. It is a consequence of the fact that the explosion characteristics strongly depend on the mechanism of action of a particular igniter. The minimum effect on the safety characteristics was observed when measuring the minimum initiation energy and the minimum ignition temperature of dust layer from the hot surface. The results of the measurements suggest that different types of peppers exhibit different explosion characteristics. This information should then be considered in explosion prevention.

Hereditary cancer syndromes caused by germline mutations account for 5-10% of all cancers. The finding of a genetic mutation could have far-reaching consequences for pharmaceutical therapy, personalized prevention strategies, and cascade testing. According to the National Comprehensive Cancer Network’s (NCCN) and the Italian Association of Medical Oncology (AIOM) guidelines, unaffected family members should be tested only if the affected one is unavailable. This article explores whether germline genetic testing may be offered to high-risk families for hereditary cancer even if a living affected relative is missing. A retrospective study was carried out on 103 healthy subjects tested from 2017 to 2023. We enrolled all subjects with at least two first or second-degree relatives affected by breast, ovarian, pancreatic, gastric, prostate, or colorectal cancer. All subjects were tested by Next Generation Sequencing (NGS) multi-gene panel of 27 cancer-associated genes. In the study population, 5 (about 5%) pathogenic/likely pathogenic variants (PVs/LPVs) were found while 40 (42%) had a Variant of Uncertain Significance (VUS). This study highlights the importance of genetic testing for individuals with a strong family history of hereditary malignancies. This approach would allow women who tested positive to receive tailored treatment and prevention strategies based on their personal mutation status.

When implementing a control system for a ground-based unmanned vehicle (UV) used in agri-culture, an important factor is the low cost of the equipment used, so the use of cameras without lidars for navigation, avoiding obstacles, and ensuring movement safety seems promising. En-suring the safety of movement of UV consists of developing methods and means that make it possible to bypass static and dynamic obstacles and make an emergency stop if it is impossible to bypass. The article describes methods and software that provide detection of objects surrounding the UV through the use of the YOLOv8 neural network, space free for movement through the use of se-mantic segmentation with the MobileNetV3 network architecture, tools for combining several data sources to build a local perception map, as well as linear and angular speed of the UV based on calculating the optimal direction of movement for avoiding obstacles. Testing of the developed methods and software was realized in the Webots simulation environment. Software is developed with ROS2.

With the rapid development of communication technology, connected vehicles (CV) have the potential, through the sharing of data, to enhance vehicle safety and reduce vehicle energy consumption and emissions. Numerous research efforts have been conducted to quantify the impacts of CV applications, assuming instant and accurate communication among vehicles, devices, pedestrians, infrastructure, the network, the cloud, and the grid, collectively known as V2X (vehicle-to-everything). The use of cellular vehicle-to-everything (C-V2X), to share data is emerging as an efficient means to achieve this objective. C-V2X releases 14 and 15 utilize the 4G LTE technology and release 16 utilizes the new 5G new radio (NR) technology. C-V2X can function without network infrastructure coverage and has a better communication range, improved latency, and greater data rates compared to older technologies. Such highly efficient interchange of information among all participating parts in a CV environment will not only provide timely data to enhance the capacity of the transportation system but can also be used to develop applications that enhance vehicle safety and minimize negative environmental impacts. However, before the full benefits of CV can be achieved, there is a need to thoroughly investigate the effectiveness, strengths, and weaknesses of different CV applications, the communication protocols, the varied results with different CV market penetration rates (MPRs), the interaction of CVs and human driven vehicles, the integration of multiple applications, and the errors and latencies associated with data communication. This paper reviews existing literature on the environmental, mobility and safety impacts of CV applications, identifies the gaps in our current research of CVs and recommends future research directions. The results of this paper will help shape the future research direction for CV applications to realize their full potential benefits.

Food-borne transmission is a recognized route for many viruses associated with gastrointestinal, hepatic or neurological diseases. Therefore, it is essential to identify new bioactive compounds with broad-spectrum antiviral activity is needed to exploit innovative solutions against these hazards. Lately, antimicrobial peptides (AMPs) have been recognized as promising antiviral agents. Indeed, while the antibacterial and antifungal effects of these molecules have been widely reported, their use as potential antiviral agents has not yet been fully investigated. Herein, the antiviral activity of previously identified or newly designed AMPs, was evaluated against the non-enveloped RNA viruses, Hepatitis A virus (HAV), and Murine Norovirus (MNV), a surrogate for human Norovirus. Moreover, specific assays were performed to recognize at which stage of the viral infection cycle the peptides could function. Results showed that almost all peptides displayed virucidal effects with about 90% of infectivity reduction on HAV or MNV. However, the decapeptide RiLK1 demonstrated, together with its antibacterial and antifungal properties, a notable reduction in viral infection for both HAV and MNV, possibly through direct interaction with viral particles or inhibition of the viral bonding to the cell receptors. Hence, RiLK1 could represent a versatile ‘antimicrobial agent effective against various foodborne pathogens including viruses, bacteria, and fungi.

Puccinia graminis f. sp. tritici (Pgt), the causal agent of wheat stem rust, poses a significant threat to global wheat production. Genetic resistance offers a cost-effective and sustainable solution. The durum wheat landrace PI 94701 was previously hypothesized to carry two stem rust resistance (Sr) genes, but their chromosomal locations were unknown. In this study, we mapped and characterized an all-stage Sr gene in PI 94701, temporarily designated as SrPI94701. In seedling tests, SrPI94701 was effective against all six Pgt races tested. Using a large segregating population (2,302 gametes), we mapped SrPI94701 within a 0.17-cM region flanked by markers pku69124 and pku69228, corresponding to 1.04- and 2.15-Mb genomic regions in the Svevo and Chinese Spring reference genomes. Within the candidate region, eight genes exhibited differential expression between the Pgt-inoculated resistant and susceptible plants. Among them, two NLR genes, TraesCS5B03G1334700 and TraesCS5B03G1335100, showed high polymorphism between parental lines, with upregulation observed in the resistant F4 line compared to its susceptible sister line. However, the flanking and completely linked markers developed in this study could not accurately predict the presence of SrPI94701 in uncharacterized wheat genotypes. SrPI94701 holds promise as a valuable component in breeding programs aimed at enhancing resistance against Pgt.

When dealing with limited sample sizes or missing values in time series data, achieving high accuracy in forecasting becomes challenging. This challenge is particularly common in wind energy forecasting, where many wind farms lack complete data. In this paper, we employ the widely-used ARIMA (Autoregressive Integrated Moving Average) model for time series forecasting. To address the difficulties posed by limited sample sizes and missing values, we adopt a unique approach by utilizing multiple ARIMA models for different datasets. A key distinction from other multiple models methods for time series forecasting lies in each model within our approach using its own dataset, making the fusion process more intricate. To overcome this, we incorporate neural networks and two techniques for model fusion: direct fusion with a learning mechanism and compensation for missing data through training. For each ARIMA model, we introduce a noise estimation method to circumvent the white noise assumptions inherent in ARIMA models. Finally, we apply these methods to wind energy prediction, and our experimental results showcase a significant enhancement in forecasting accuracy.

Nocardia is an emerging bacterial disease that often affects patients with compromised immune systems. As survival increases, more and more patients are receiving solid organ transplantations, and more patients are cancer survivors and receiving long-term immune system modifying agents or corticotherapy and immunosuppressive agents, organisms that are not harmful in usual circumstances become a public health problem. Carbapenems are usually a second-line therapy in the setting of Nocardia infections. We present the case of a patient who had an immunocompromised status and was diagnosed with Nocardia farcinica, which showed in vitro resistance to carbapenems. The symptoms were non-specific and had a common presentation, although the infection was disseminated and had severe CNS and ocular involvement. The clinical course was more severe when the carbapenem was withdrawn based on the provided antibiogram and markedly improved when clinical judgment considered it might be beneficial. The first case in our region to describe an „in vitro” carbapenem-resistant Nocardia species, that responded „in vivo” differently and we believe it is important to remind clinicians of this potentially severe disease in difficult cases.

In this paper, we present an experimental procedure to enhance the dimensional accuracy of fabrication via Stereolithography (SLA) of features at the micro-scale. Using a custom benchmark part, deviations in feature dimensions (micro-pores diameters and depths) were detected and measured by confocal microscopy. Samples characterization and experimental observations allowed the identification of inaccuracy sources, mainly due to the laser beam scanning strategy and to the incomplete removal of uncured liquid resin in post-processing (i.e., IPA washing). As a technology baseline, the measured dimensional errors on pores diameters were up to -46%. A compensation method of the nominal laser spot diameter (85m) was defined and implemented resulting in relevant improvements in dimensional accuracy of 9.8% and 11.3% on full-open pores diameter and depth, respectively. Further investigation was performed on a customized test part to adjust the calibration procedure. The measurements revealed that the estimate of the laser beam spot size is 968m. Measurements on micro-pores having different sizes revealed that a constant compensation parameter (i.e., C=85, 96, 120m) is not fully effective at the micro-scale, where average errors still remain at -24%, -18.8%, and -16% for compensations equals to 85, 96 and 120m, respectively. A further experimental campaign allowed the identification of an effective nonlinear compensation law where the compensation parameter depends on the micro-feature size C= f (D). Results show a sharp improvement in dimensional accuracy on micro-pore fabrication, with errors consistently below +8.2%. The proposed compensation method can be extended for the fabrication of any micro-features without restrictions on the specific technology implementation. Concerning the inaccuracy introduced by the laser path, experimentation with a customized part allowed the optimization of the part orientation to reduce the errors and their differences along the X and Y machine axes.

Glioblastoma (GBM) is the most common malignant primary brain tumor, with a median survival rate of less than two years. Currently, there is no cure for GBM, underscoring the urgent need for innovative treatment approaches. Vaccine design emerges as a crucial strategy, offering a safe and effective means for both preventive and therapeutic interventions against GBM. In this study, we targeted four GBM-associated mutated surface proteins—urokinase plasminogen activator sur-face receptor (PLAUR), integrin beta-3 (ITGB3), and the B-41 alpha chain (HLA-B) and A-24 alpha chain (HLA-A) of the HLA class I histocompatibility antigens—to design a peptide-based vaccine. The vaccine construct includes cytotoxic T lymphocyte (CTL) and T helper cell (Th cell) epitopes, and was meticulously evaluated for antigenicity, allergenicity, and toxicity. The results indicate that the vaccine is antigenic and non-allergenic, making it a promising candidate. Additionally, the physico-chemical properties of the vaccine suggest stability and suitability for further de-velopment. Immune simulation studies predict efficient immune responses upon vaccine ad-ministration. Our vaccine shows promise as a potential tool in the fight against GBM, offering new hope for patients facing this devastating disease.

Frontal Polymerization (FP) is recognized as a polymer synthesis method capable of generating a highly localized and self-propagating exothermic front, considered a more rapid and energy-efficient manufacturing scheme for polymer-based fiber-reinforced composite materials. This study conducts a numerical investigation based on the Finite Element Method into the initiation and propagation of frontal polymerization of acrylamide. Utilizing Differential Scanning Calorimetry (DSC) experiments, the study phenomenologically tests the curing kinetics reactions of acrylamide (AM) in deep eutectic solvent (DES)-based polymerizable systems, thereby establishing a curing kinetics model for the autocatalytic reaction of polyacrylamide. By coupling the heat conduction diffusion equation of the frontal polymerization reaction, the Finite Element Method is employed to solve the reaction-diffusion model, aiming to explore the evolution of temperature and degree of curing during the manufacturing process. The results demonstrate the reliability and accuracy of the nth-order autocatalytic model in the study of curing kinetics for DES-based synthesis, indicating that the front propagation speed of the AM-based FP reaction is influenced by the activation temperature, duration of activation temperature, and initial temperature of the solution. Experimental validation of the polyacrylamide manufacturing through frontal polymerization corroborates the accuracy and reliability of the model predictions, providing a reference for the numerical model study and temperature control in the synthesis of acrylamide composite hydrogels via FP.

A review of quantitative risk assessment (QRA) models of L. monocytogenes in produce was carried out, with the objective of appraising and contrasting the effectiveness of the control strategies placed along the food chains. Despite nine of the thirteen QRA models recovered focused on fresh or RTE leafy greens, none of them represented important factors or sources of contamination in the primary production, such as type of cultivation, water, fertilisers or irrigation method/practices. Cross-contamination at processing and during consumer’s handling was modelled using transfer rates, which were shown to moderately drive the final risk of listeriosis; highlighting therefore the importance of accurately representing the transfer coefficient parameters. Many QRA models coincided in the fact that temperature fluctuations at retail or temperature abuse at home were key factors contributing to increasing the risk of listeriosis. In addition to a primary module that could help assess current on-farm practices and potential control measures, future QRA models for minimally-processed produce should also contain a refined sanitisation module able to estimate the effectiveness of various sanitisers as a function of type, concentration and exposure time. Finally, L. monocytogenes growth in the products down the supply chain should be estimated by using realistic time-temperature trajectories, and validated microbial kinetic parameters, both of them currently available in the literature.

This study developed a three-dimensional kinematic and dynamic model of a center-driven linkage system (CDLS). Force analysis was conducted to determine the required driving torque to ensure that the input link of the CDLS rotates at a constant speed with a certain angular velocity, even in the presence of frictional resistance torque. The primary objective was to optimize the maximum angular acceleration of the output links to reduce wiper noise. This optimization can enhance the stability of the linkage system while maintaining its operational functionality. In the adopted methodology, the frames of the fixed links are assumed to remain unchanged, and the input link is considered to operate at a constant angular speed and have a constant length. To meet standard vehicle windshield wiper requirements, 10 constraints were imposed on the optimization problem, which was solved using the differential evolution method. The lengths of both output links were reduced by over 10% after optimization.

Laser range-gated underwater imaging technology, by removing most of the back scattering noise, can effectively increase the image contrast and extend the detection range. The optical signal captured by a range-gated imaging system primarily comprises reflected light from the object and backscattered light from the surrounding water. Consequently, surfaces with low reflectivity or highly turbid water environments substantially constrain the applicability of the range-gated imaging system. To enhance the detection capability of underwater laser range-gated imaging, this paper proposes the incorporation of underwater polarized light imaging technology as an enhancement method. Based on polarization differences, backscattered light and reflected light from an object can be distinguished. Experimental results indicate that, compared to images obtained using a conventional range-gated laser imaging system, those captured with a polarization-enhanced system exhibit an increase of up to 47%. The proposed approach, which integrates polarization imaging with range-gated laser imaging, has the potential to broaden the applicability of underwater laser imaging scenarios.

Background: The Second Victim Phenomenon (SVP) significantly impacts the well-being of healthcare professionals and patient safety. While SVP has been explored in various healthcare settings, there is limited data on its prevalence and associated factors among nurses in Austria. This study investigates the prevalence, symptomatology, and preferred support measures for SVP among Austrian nurses. Methods: A nationwide, cross-sectional, anonymous online survey was conducted using the SeViD questionnaire (Second Victims in German-speaking Countries), which includes the Big Five Inventory-10 (BFI-10). Statistical analyses included binary logistic regression and multiple linear regression using the bootstrapping, bias-corrected and accelerated (BCa) method based on 5000 bootstrap samples. Results: 928 participants responded to the questionnaire. Among the respondents, 81.58% (744/912) identified as Second Victims (SVs). The primary cause of becoming a SV was aggressive behavior from patients or relatives. Females reported a higher symptom load than males, and higher agreeableness was linked to increased symptom severity. Notably, 92.47% of SVs who sought help preferred support from colleagues, and the most pronounced desire among participants was to process the event for better understanding. Conclusions: The prevalence of SVP among Austrian nurses is alarmingly high, with aggressive behavior identified as a significant trigger. The findings emphasize the necessity for tailored support strategies, including peer support and systematic organizational interventions to mitigate the impact of SVP on nurses and to improve overall patient care. Further research should focus on developing and implementing effective prevention and intervention programs for healthcare professionals in similar settings.

Opuntia ficus-indica (L.) Mill. belongs to the Cactaceae family and the genus Opuntia; it is a succulent plant that adapts to extreme climatic conditions. The aerial part of the plant consists of the cladodes, morphological changes of branches that appear green, are covered with thorns, and are essential to reduce excessive perspiration of water. The composition of cladodes is very varied, and the main constituents are water, fibers, polysaccharides, proteins, fatty acids, vitamins, sterols, minerals, and polyphenols. Polyphenols are responsible for many beneficial activities for human health, such as antioxidant, anti-inflammatory, antitumor, and nutritional properties. The purpose of this manuscript was to compare the properties of cladodes belonging to the same plant but with different stages of maturity. Relative extracts were tested both in vitro and on a cell line and antioxidant and anti-apoptotic properties were found. The antioxidant activity was tested by the ORAC test, the DPPH test, and the measurement of cellular accumulation of ROS. Anti-apoptotic activity was evaluated by the annexin/PI assay and measurement of caspases 9 and 3 expression. The results obtained have shown that the extracts considered possess antioxidant and anti-apoptotic properties. However, the different stages of maturity of cladodes are essential for the performance of both functions. In addition, important variations have been made in the dissolution of extracts that have brought greater safety in their use. In conclusion, this manuscript provides further information on cladodes of Opuntia ficus-indica, which can be used as adjuvants in many human pathologies.

This study investigates the impact of thin flame combustor design on hydrogen flame characteristics and combustion performance through numerical simulations. Variations in flame shape and combustibility between 100% methane and 100% hydrogen combustion are analyzed. Three combustor header shapes (flat, concave, and convex) are modeled to assess their influence on flame behavior. Results show distinct flow patterns, with concave headers promoting strong central flows and convex headers dispersing the flow outward. Temperature field analysis indicates that hydrogen flames have higher temperatures and shorter quenching distances compared to methane flames. A comparative analysis of combustion products is conducted to evaluate combustion performance and NOx emissions. Consequently, the concave header has high combustibility and increases temperatures and NOx fraction in hydrogen combustion.

Drowning is a leading cause of accidental death worldwide, with traditional drowning prevention strategies focused on buoyancy aids and protective equipment proving insufficient in mitigating the immediate risks of cold water shock and drowning. Swiftwater Breathing Apparatus (SWBA) has emerged as a potential game-changer, offering respiratory protection at the water's surface and a means of interrupting the drowning process. This report examines how SWBA can disrupt the drowning process, the benefits of using SWBA compared to existing protective equipment, the issue of water rescuer fatalities, and the potential implications for insurers and coronial inquests.

The paper provides a discussion on the results of studies of the effect exerted by combined degradation factors typical of four types of wear: abrasion, impact-abrasion, tribocorrosion, and impact-abrasion-corrosion, conducted for chain wheels made of Ni-Cu alloyed Austempered Ductile Iron. The studies consisted in determining the content of retained austenite in the structure of the cast irons in question, establishing the measures of wear following wear testing, and identifying basic surface degradation mechanisms observed in the chain wheels tested following multifactorial wear processes. The chain wheels made of ADI were found to have sustained the greatest damage under the impact-abrasion-corrosion (three-factor) wear scenario, while the wear was least advanced in the abrasion (one-factor) wear case. Another observation derived from the studies is that the combined effect of dynamic forces, corrosion, and quartz sand-based abrasives causes increased surface degradation in the cast iron grades taken into consideration compared to processes characterised by a reduced number of degradation factors (i.e. one- or two-factor wear processes). Additional hardness tests and XRD analyses have revealed a distinctive effect attributable to combined degradation factors on the surface hardness increase value and implied that bench testing was followed by phase transition.

Due to the continued deepening of today’s mining projects, there is a need to develop new or improved rockbolts that are strong and yielding and have high energy absorption when exposed to dynamic loading. Impact tests can provide useful information about the dynamic response of rockbolts but most laboratory tests involve high costs in preparation and result validation. Numerical modeling is an alternative that, in addition to complementing laboratory results, can be used to represent the process of deformation and energy absorption of support elements. In this paper the implementation and results obtained from a finite difference (FDM) numerical model are presented. The model functions as a simulation tool to illuminate all the elements that conform the large-scale (1:1) impact test and their behavior and influence on the dynamic response of a threadbar bolt (22 mm nominal diameter). The model was calibrated using published results and based on these results as well as parametric analysis, the response of each component (steel tube, grout, and bolt) could be identified and its behavior in terms of absorbed energy and displacement could be observed. Results show the model can provide important preliminary information to make design decisions about support elements design.

Unmanned aerial vehicles (UAVs) represent a new model of social robots for home care of dependent persons. In this regard, this article introduces a study on people’s feeling of safety and comfort while watching the monitoring trajectory of a quadrotor dedicated to determining their condition. Three main parameters are evaluated: the relative monitoring altitude, the monitoring velocity and the shape of the monitoring path around the person (ellipsoidal or circular). For this purpose, a new trajectory generator based on a state machine, which is successfully implemented and simulated in MATLAB/Simulink®, is described. The study is carried out with 37 participants using a virtual reality (VR) platform based on two modules, UAV Simulator and VR Visualiser, both communicating through the MQTT protocol. The participants’ preferences have been a high relative monitoring altitude, a high monitoring velocity and a circular path. These choices are a starting point for the design of trustworthy socially assistive UAVs flying in real homes.

The permanent protection of groundwater and surface sources of drinking water in the required raw water quality from contamination is the primary foundation of preserving the life of society and the entire engineering infrastructure operability not only in the Czech Republic but also in other countries of the world. One of the basic ways of contamination prevention enhancement and risk mitigation of putting a water source out of operation is the identification of the given risk as well as soil contamination monitoring. The purpose of this study is to understand specific aspects of contamination threats to drinking water sources and determine possible solutions to eliminate the risk, shown in the example case study in the Czech Republic conditions. Based on the findings, a proposal to enhance the prevention of water source contamination has been elaborated in the form of recommendations regarding the ways and means used to monitor the risk areas and to implement technical measures so as to eliminate or terminate the specified risk. A complex approach based on the integration of interdisciplinary factors and methodology is required to minimize the threats of aquatic ecosystems contamination in the Czech Republic.

Advanced glycation end products (AGEs) play a significant role in the aging processes, further regarding as a hallmark of aging. Despite the importance, a lack of monitoring tools has hampered the study of relationship between AGEs and aging. Here, we firstly report a novel AGEs-selective probe, AGO. AGO presented its ability to detect AGEs more sensitively than a conventional approach of measuring autofluorescence from AGEs. In addition, we confirmed that AGO can detect AGEs depending on kinetics, reflecting by a preference to ribose-derived AGEs. Finally, AGO revealed its competence to visualize glycation products in glycation mimicking model, made by collagen framework. We believe that this study will enrich molecular toolboxes to understand physiological processes of AGEs during aging processes.

The rheological properties of a polyamide (PA) resin with low crystallinity were modified by melt-mixing it with a small amount of an alternative a-olefin–maleic anhydride copolymer as a reactive compound. Because PA has a low melting point, rheological characterization was performed over a wide temperature range. Owing to the reaction between PA and the alternative a-olefin–maleic anhydride copolymer, the blend sample behaved as a long-chain branched polymer in the molten state. The thermo-rheological complexity was obvious owing to large flow activation energy values in the low modulus region. The primary normal stress difference under steady shear was greatly increased in the wide shear rate range, leading to a large swell ratio at capillary extrusion. Furthermore, strain hardening in the transient elongational viscosity, which is responsible for favorable processability, was clear. Because this is a simple modification method, it will be widely employed to modify the rheological properties of various polyamide resins.

The efficient preparation of single-stranded DNA (ssDNA) rings, as a macromolecular construction approach with topological features, has aroused much interest due to their numerous applications in biotechnology and DNA nanotechnology. However, an extra splint is essential for enzymatic circularization, and by-products of multimers are usually present at high concentrations. Here, we proposed a simple and robust strategy of using permuted precursor (linear ssDNA) for circularization by forming an intramolecular dynamic nick using a part of the linear ssDNA substrate itself as the template. After the simulation of the secondary structure for desired circular ssDNA, the linear ssDNA substrate is designed to have its ends on the duplex part (≥5 bp). By using this permuted substrate with 5'-phosphate, the splint-free circularization is simply carried out by T4 DNA ligase. Very interestingly, formation of only several base pairs (2–4) flanking the nick is enough for ligation, although they form only instantaneously under ligation conditions. More significantly, the 5 bp intramolecular duplex part commonly exists in genomes or functional DNA, demonstrating the high generality of our approach. Our findings are helpful for understanding the mechanism of enzymatic DNA ligation from the viewpoint of substrate binding.

Ten new Schiff bases, including thiocarbohydrazone derivatives (1–10), were synthesized using an efficient, uncomplicated, and environmentally friendly approach using the reaction of alkyl-substituted aldehydes. The thiocarbohydrazones that were obtained were derived from o-phthalaldehyde. The chemical structures of the compounds were identified by the utilization of UV-Vis spectroscopy, Fourier transform infrared (FT-IR), ¹H nuclear magnetic resonance (¹H NMR), ¹³C nuclear magnetic resonance (¹³C NMR), and elemental analysis methods. The thermal stability of thiocarbohydrazones was examined using thermogravimetric analysis (TGA-DSC). Investigations were conducted on urease inhibition tests, pharmacokinetic property research, and molecular docking. The collection of samples with the urease enzyme revealed significant molecular docking findings, with MolDock scores ranging from -153 to -189. The compounds have the potential to be effective drug candidates for treating certain diseases, as indicated by the consistent results of molecular docking, urease inhibition tests, and pharmacokinetic characteristics investigations.

Background and Objectives: In the literature, relationships between being married and having prediabetes or diabetes are inconsistent. We aimed to investigate whether marriage is a protective or risk factor for prediabetes and to uncover new insights into its impact on prediabetes. Materials and Methods: In this cross-sectional observational study, questionnaires were distributed by email to 1,039 staff members who participated in an employee health check from a hospital affiliated with a medical university in Taiwan. Fasting blood glucose and triglyceride (TG) levels were checked and the questionnaires elicited basic demographic characteristics and included the Copenhagen Burnout Inventory and Nordic Musculoskeletal Questionnaire. The chi-square test or Fisher’s exact test, logistic regression, and mediation analysis were conducted for statistical analysis. Results: Among the group aged 20–37 years, married, obesity, neck and shoulder pain, and elevated TG levels were independent risk factors for prediabetes (impaired fasting glucose). For those >38 years old, overweight, obesity, and elevated triglyceride (TG) were the independent risk factors for impaired fasting glucose. Increased TG levels serve as a mediating factor linking marriage to an increased risk of prediabetes for the group aged 20–37 years. Conclusions: TG play a significant role in the association between marriage and prediabetes among the group aged 20–37 years. Therefore, dietary habits, especially those of young adult couples should be considered. Our findings connect marital status to prediabetes, facilitating advances in diabetes prevention.

While Retrieval-Augmented Generation (RAG) enhances Large Language Models (LLMs), it also presents challenges that can affect model accuracy and performance. Practical applications show that RAG can mask the intrinsic capabilities of LLMs. Firstly, LLMs may become overly dependent on external retrieval, underutilizing their own knowledge and inference abilities, which can reduce responsiveness. Secondly, RAG techniques might introduce irrelevant or low-quality information, adding noise to the LLM. This can disrupt the normal generation process, leading to inefficient and low-quality content, especially when dealing with complex problems. This paper proposes a RAG framework that uses reflective tags to control retrieval. This framework evaluates retrieved documents in parallel and incorporates the Chain of Thought (CoT) technique for step-by-step content generation. The model selects the highest quality and most accurate content for final generation. The main contributions include: 1) Reducing the hallucination problem by selectively utilizing high-scoring document, 2) Enhancing real-time performance through timely external database retrieval, and 3) Minimizing negative impacts by filtering out irrelevant or unreliable information through parallel content generation and reflective tagging. These advancements aim to optimize the integration of retrieval mechanisms with LLMs, ensuring high-quality and reliable outputs.

This study delves into the critical domain of public procurement, specifically focusing on Sustainable Public Procurement (SPP) and Environmental, Social, and Governance (ESG) considerations within the context of South Korea. The aim of this research is to empirically scrutinize the factors influencing the impact index of SPP, with a particular emphasis on services related to labor standards. The investigation spans three years, from January 1, 2019, to July 31, 2021, encompassing state agency orders and post-implementation legal changes. Leveraging the comprehensive Korea On-line E-Procurement Sys-tem(KONEPS) platform, we meticulously collected data, ultimately culminating in 21,573 services meeting our criteria, from which 250 cases underwent an in-depth analysis. The study sheds light on the influence of social responsibility evaluation cri-teria on overall procurement scores, while also uncovering the moderating effects of various factors. The outcomes of this study offer valuable insights into the impact index of social responsibility evaluation criteria within South Korea's public procurement landscape. Factors including procurement year, classification, service period, and estimated price were identified as significant influencers. Moreover, the number and location of evalu-ation criteria items, inclusion of sincerity elements, and the evaluating agency were deemed pivotal determinants of the influence index. These findings hold profound implications for policymakers, procurement practitioners, and researchers and provide a roadmap for optimizing the utilization of social responsibility evaluation criteria to advance responsible and sustainable procurement practices. Future research avenues include conducting further study of additional moderat-ing variables, expanding datasets to encompass a broader spectrum of procurement contexts, and evaluating the long-term repercussions of social responsibility evaluation on procurement outcomes. These endeavors promise to further refine and advance public procurement practices in South Korea and beyond.

To better understand the shape memory materials and self-healing materials, a new series of liquid-crystalline shape memory polyurethane (LC-SMPU) composites, named SMPU-OOBAm, were successfully prepared by incorporating 4-octyldecyloxybenzoic acid (OOBA) into the PEG-based SMPU. The effect of OOBA on the structure, morphology and properties has been carefully investigated. The results demonstrate that SMPU-OOBAm have liquid crystalline properties, triple-shape memory properties and self-healing properties. The incorporated OOBA promotes the crystallizability of both soft and hard segments of SMPU, and the crystallization rate of the hard segment of SMPU decreases when the OOBA-content increases. Additionally, the SMPU-OOBAm forms a two-phase separated structure (SMPU phase and OOBA phase), and it shows two-step modulus changes upon heating. Therefore, the SMPU-OOBAm shows triple-shape memory behavior, and the shape recovery ratio decreases with an increase in the OOBA content. Finally, SMPU-OOBAm shows self-healing properties. The new mechanism can be ascribed to the heating-induced “bleeding” of OOBA in the liquid crystalline state and the subsequent re-crystallization upon cooling. This successful combination of liquid crystalline properties, triple-shape memory properties and self-healing properties make the SMPU-OOBAm composites with many promise applications in smart optical devices, smart electronic devices and smart sensors.

After an introductory reminder of safety concerns pertaining to early rechargeable battery technologies, this review discusses current understandings and challenges of sodium-ion batteries. Sodium-ion technology is now being marketed by industrial promoters who are advocating its workable capacity, use of readily accessible and cheaper key cell components. Often claimed to be safer than lithium-ion cells, currently only limited scientific-sound safety assessment of sodium-ion cells has been performed. However, the predicted sodium-ion development roadmap reveals that significant variants of sodium-ion batteries will potentially enter the market in the near future. With recent experiences of lithium-ion battery failures, sodium-ion battery safety management will constitute a key aspect of successful market penetration. As such this review discusses the safety issues of sodium-ion batteries presenting a twofold innovative perspective: i) in terms of comparison with the parent lithium-ion technology making use of the same working principle and similar flammable non-aqueous solvent basis and ii) anticipating the arrival of innovative sub-chemistries at least partially inspired from successive generations of lithium-ion cells. The authors do hope that the analysis provided will assist the concerned stakeholders in the quest for safe marketing of sodium-ion batteries.