Over the last two decades, a considerable amount of equipment has been acquired (spreaders, seeders, sprayers, among others) to respond to the challenges of Precision Agriculture (PA) concept. Most of this equipment has been purchased at a high cost. However, many of them, despite still being functional and equipped with sensors, actuators, and electronic processing units capable of adjusting to variations in speed, have become obsolete in terms of communication, and incompatible with new monitoring and control systems based on the “Isobus” protocol. This work aims to present a solution for updating the control system (“Ferticontrol”) of a “Vicon RS-EDW” spreader with variable rate application (VRA), making it compatible with the “InCommand” system from “Ag Leader”. The solution includes low-cost “Arduino” and “Raspberry Pi” microcontrollers and open-source software. The development shows that it is possible to implement a solution that is accessible to farmers in general. It also provides a niche business opportunity for young researchers to set up small technology-based enterprises associated with universities and research centers. These partnerships guarantee permanent innovation and represent a decisive step towards modern, technological, competitive, and sustainable agriculture.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

Plastic contamination of small dimensions (

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

The COVID-19 pandemic has triggered seismic shifts in how we work, and organizations behave. It has caused many organizations to transition from an office-centric culture to more flexible ways of working. This shift is necessitated by health conditions and the need for controls. It is also driven by the assumption that remote work or working from home offer a certain assurance of safety for employees against the threat of infection in highly vulnerable office conditions. The shift to remote work has so far been mainly experimental as most businesses continue to learn about what works and what doesn’t. There is also the assumption that all that matters for the efficient operability of a remote work regime is the availability and effectiveness of computing technologies and internet connectivity. Thus, once those supplies are in place remote work is expected to be fully functional and without problems. As learning continues about what works and what doesn’t, it has also become increasingly clear that beyond the threat of covid-19 and the relative safety that individual homes may offer, there are other vulnerabilities which are ignored or underestimated in the process. In most instances, the home environment of the employee, the conditions under which employees operate from home and the health and safety such environments provide (or not) are either ignored or underestimated in discussions around remote work practices. This paper highlights remote work as an emergent practice while exploring associated, but ignored, health and safety issues in employee homes.

The Upper Hunter Valley is a major coal mining area containing approximately 40% of the currently identified total coal reserves in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. This paper summarises the spatial and temporal variability modes of PM10 pollution in the region, based on long-term multi-site monitoring data and the application of the rotated principal component analysis (RPCA) and wavelet analysis techniques. RPCA identified two distinct air quality clusters/subregions in the valley, one in the west/northwest, the other in the southeast. Wavelet analysis revealed the annual cycle to be most persistent temporal mode of PM10 variability in both subregions, with intermittent signals observed at time scales of around 120, 30~90 and under 30 days. How these variation modes are related to the effects of local PM10 emissions and the influence of meteorology at different time scales deserves further attention in future work. The findings will be used in air quality reporting and forecasting in NSW. The methodology and results can also be useful for air quality research in similar regions elsewhere.

Off-grid electrification planning increasingly recognizes the importance of productive use of electricity (PUE) to promote community value creation and (financial) project sustainability. To ensure a sustainable and efficient integration in the community and energy system, PUE assets must carefully be evaluated to match both the community needs and the residential electricity demand patterns. We propose a novel methodology interlinking qualitative interviews, statistical analysis, and energy system modelling to optimize decision-making for PUE integration in off-grid energy systems in rural Madagascar by aligning relevant PUE effectively with anticipated residential electricity demand patterns based on socio-economic determinants of the community. We find that a possible contribution of the PUE to reducing the electricity costs depends signifi-cantly on three factors: 1. the residential electricity consumption patterns that are influenced by the socio-economic composition of the community, 2. the degree of flexibility of i) PUE assets and ii) operational preferences of the PUE user, and 3. the capacity of community members to finance and operate PUE assets. Our study demonstrates that significant cost reductions for PUE-integrated off-grid energy systems can be achieved by applying our proposed methodology. When matching PUE and residential consumption patterns, the integration of PUE assets in residential community energy system can reduce the financial risk of operators, provided the PUE enterprise operates reliably and sustainably. We highlight that the consideration of local value chains and co-creation approaches are essential to ensure the energy system is addressing the community’s needs, creates value for the community, enhances the project´s financial sustainability, and is achieving the overall objectives of decentralized energy system planning.

In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

Understanding the structural intricacies of RNA molecules is essential for deciphering numerous biological processes. Traditionally, scientists have relied on experimental methods to gain insights and draw conclusions. However, the recent advent of advanced computational techniques has significantly accelerated and refined the accuracy of research results in several areas. A particularly challenging aspect of RNA analysis is the prediction of its secondary structure, which is crucial for elucidating its functional role in biological systems. This paper deals with the prediction of pseudoknots in RNA, focusing on two types of pseudoknots: K-type and M-type pseudoknots. Pseudoknots are complex RNA formations in which nucleotides in a loop form base pairs with nucleotides outside the loop and thus contribute to essential biological functions. Accurate prediction of these structures is crucial for understanding RNA dynamics and interactions. Building on our previous work in which we developed a framework for the recognition of H- and L-type pseudoknots, an extended grammar-based framework tailored to the prediction of K- and M-type pseudoknots is proposed. This approach uses syntactic pattern recognition techniques and provides a systematic method to identify and characterize these complex RNA structures. Our framework uses context-free grammars (CFGs) to model RNA sequences and predict the occurrence of pseudoknots. By formulating specific grammatical rules for type K and type M pseudoknots, we enable efficient parsing of RNA sequences to recognize potential pseudoknot configurations. This method ensures an exhaustive exploration of possible pseudoknot structures within a reasonable time frame. In addition, the proposed method incorporates essential concepts of biology, such as base pairing optimization and free energy reduction, to improve the accuracy of pseudoknot prediction. These principles are crucial to ensure that the predicted structures are biologically plausible. By embedding these principles into our grammar-based framework, we aim to predict RNA conformations that are both theoretically sound and biologically relevant.

Language is an essential aspect of teaching and learning mathematics. It is necessary for communicating, transmission of concepts and ideas, and formation of meaning of mathematical concepts. In mathematics, besides symbols, which are usually common in different languages, words and expressions are used, which may invoke different concept images to students in various languages. Some words are used in mathematics and in everyday language with different meanings, while others are used only in mathematics or in mathematics and other disciplines in similar but non-identical ways. In Mathematical Analysis, the used vocabulary is gradually enhanced, and the concepts are defined in a more formal way. In the current study, the language used regarding mathematics of change is examined, focusing on rate of change and in relation to misconceptions of students.

Human induced climate change led to the recognition of Community-Based Adaptation (CBA) as one of the remedies in building adaptive capacity and resilience of communities. It recognizes the agency of communities in shaping the optimal strategy. CBA interventions are vital in addressing community needs and contextual specificities, enable participatory and inclusive engagement and thereby facilitate more profound adaptation impacts. Agent-based modelling (ABM) has the potential to be an invaluable approach in developing tailored adaptation strategies considering capacities, resources, skills, priorities, needs and the cultural context of local communities. ABM allows to capture the complex relationships among various components within community decision making on CBA actions, the CBA actions themselves and the environment, however available tools provide for various degrees of freedom in agent definition, sensitivity analysis, scalability, experiment design and output analysis to name a few. This article assesses all available ABM modelling and simulation tools for its application in the context of CBA. NetLogo emerges as the most suitable tool for incorporating and handling the special features of CBA. It is closely followed by GAMA and Envision. The article provides insights and guidance to researchers and practitioners in selecting ABM tools aligned with the specific requirements of their CBA simulations and projects.

In recent years, research on adversarial attack techniques for remote sensing object detection (RSOD) has made great progress. Still, most of the research nowadays is on end-to-end attacks, which mainly design adversarial perturbations based on the prediction information of the object detectors (ODs) to achieve the attack. These methods do not discover the common vulnerabilities of the ODs and thus the transferability is weak. Based on this, this paper proposes a foreground feature approximation (FFA) method to generate adversarial examples (AEs) that discover the common vulnerabilities of the ODs by changing the feature information carried by the image itself to implement the attack. Specifically, firstly, the high-quality predictions are filtered as attacked objects using the detector, after which a hybrid image without any target is made, and the hybrid foreground is created based on the attacked targets. The images' shallow features are extracted using the backbone network, and the features of the input foreground are approximated towards the hybrid foreground to implement the attack. In contrast, the model predictions are used to assist in realizing the attack. In addition, we have found the effectiveness of FFA for targeted attacks, and replacing the hybrid foreground with the targeted foreground can realize targeted attacks. Extensive experiments with seven rotating ODs on the RSOD datasets DOTA and UCAS-AOD show that FFA achieves both targetless and targeted attacks with a high success rate and transferability.

This paper represents the first investigation into the consensus problem of linear time-varying multi-agent systems utilizing an event-triggered communication scheme. First, a general event-triggered consensus control scheme is proposed for a general category of linear time-varying multi-agent systems. Under some suitable assumptions, it is demonstrated that all agents’ states will converge exponentially, with Zeno behaviour being ruled out. Second, the consensus problem in a network of linear time-varying multi-agent systems with a spanning tree is investigated using the proposed control strategy. It demonstrates that the consensus issue for the specified system can be reformulated as a stabilization problem for an error system through a time-varying linear transformation. Then, the event-triggered consensus problem is just a special instance of the general event-triggered consensus problem mentioned above. Finally, to illustrate the efficacy of the event-triggered method proposed in this study, simulation results are shown.

Climate simulations in West Africa have been attributed with large uncertainties. Global climate projections are not consistent with changes in observations at the regional or local level of the Niger basin, making management of hydrological projects in the basin uncertain. This study evaluates the potential of using the quantile mapping bias correction to improve the Coupled Model Intercomparison Project (CMIP5) outputs for use in hydrology impact studies. Rainfall and temperature projections from 8 CMIP5 Global Climate Models (GCM) were bias corrected using the quantile mapping approach. Impacts of climate change was evaluated with bias corrected rainfall, temperature and potential evapotranspiration (PET). The IHACRES hydrological model was adapted to the Niger basin and used to simulate impacts of climate change on discharge under present and future conditions. Bias correction significantly improved the accuracy of rainfall and temperature simulations compared to observations. Nash coefficient (NSE) for monthly rainfall comparisons of 8 GCMs to the observed was improved by bias correction from 0.69 to 0.84. The standard deviations among the 8 GCM rainfall data were significantly reduced from 0.13 to 0.03. Increasing rainfall, temperature, PET and river discharge were projected for all GCMs used in this study under the RCP8.5 scenario. These results will help improving projections and contribute to the development of sustainable climate change adaptation strategies.

The Double Diaphragm Forming (DDF) process uses vacuum pressure and heat to pre-shape composite reinforcements between flexible diaphragms. Accurate modelling of heat transfer within DDF requires knowledge of the thermophysical properties of the constituent materials. This study investigates the specific heat and thermal conductivity of silicone diaphragms, carbon fibers (chopped and powdered), thermoplastic veils, and their combinations. Experiments measured the specific heat of each material using differential scanning calorimetry and the thermal conductivity of silicone and carbon fabric preforms using the transient plane source method and modified transient plane source method respectively. The influence of reheating cycles on specific heat of carbon fiber-veil samples and the effect of compaction on thermal conductivity of silicone and carbon fabrics were explored. While silicone exhibited linear specific heat behavior, the thermoplastic veil showed non-linearity due to phase change. The combined carbon fiber-veil samples demonstrated slight non-linear specific heat variations depending on reheating cycles. Thermal conductivity of the fabric preforms decreased with the addition of thermoplastic veil and under vacuum-compaction conditions. The established temperature-dependent property relationships provide valuable data for optimizing DDF preforming parameters and enhancing energy efficiency in composite manufacturing.

Coupling faults that occur simultaneously widely exist in the operation of mechanical equipment, and coupling fault features are formed by nonlinear coupling of multiple base fault features. In this paper, hypergraph neural network is used to obtain the characteristics of coupling faults, and two coupling fault diagnosis frameworks based on hypergraph are provided. 1. Coupling fault diagnosis framework based on feature generation: The hypergraph neural network is used as a generator to provide negative samples for discriminator training. The generator outputs hyperedge vectors as fake samples, and each hyperedge connects a base fault containing a fault type. 2. Coupling fault diagnosis framework based on feature extraction: Each node is regarded as a fault type, and the fault characteristics of each type of fault are extracted through the aggregation operation of hypergraph. The attention mechanism is introduced to realize the dynamic adjustment of the hyperedge, and the dynamic vertex is used to classify the unknown faults. The results show that the diagnostic accuracy of coupling faults under the two frameworks reaches 88.6% and 86.76%, respectively.

To overcome the time-consuming drawbacks of Computational Fluid Dynamics (CFD) numerical simulations, this paper proposes a hybrid model based on a parallel architecture based on the concept of intelligent aerodynamics, named PA-TLA (Parallel Architecture combining TCN, LSTM, and Attention mechanism). This model utilizes CFD data to drive efficient predictions of aircraft wake evolution at different initial altitudes during the approach phase. Initially, CFD simulations of continuous initial altitudes during the approach phase are used to generate aircraft wake evolution data, which are then validated against real-world LIDAR data to verify their reliability. The PA-TLA model is designed based on a parallel architecture, combining Long Short-Term Memory networks (LSTM), Temporal Convolutional Networks (TCN), and a tensor concatenation module based on the attention mechanism, which ensures computational efficiency while fully leveraging the advantages of each component in a parallel processing framework. The study results show that the PA-TLA model outperforms both the LSTM and TCN models in predicting the three characteristic parameters of aircraft wake: vorticity, circulation, and Q-criterion. Compared to the serially structured TCN-LSTM, PA-TLA achieves an average reduction in mean squared error (MSE) by 6.80%, mean absolute error (MAE) by 7.70%, and root mean square error (RMSE) by 4.47%, with an average increase in the coefficient of determination (R²) by 0.36%, and a 35% improvement in prediction efficiency. Lastly, this study combines numerical simulation and the PA-TLA deep learning architecture to analyze the characteristics of wake evolution during the near-ground phase, providing theoretical value for further reducing aircraft wake intervals and enhancing airport operational efficiency.

Mechanical equipment is composed of several parts, the interaction between the parts exists throughout whole life cycle leads to the widespread phenomenon of fault coupling and the diagnosis of independent faults cannot meet the requirements of the health management of mechanical equipment under actual working conditions. In this paper, the topological structure of graph neural network is used to describe the correlation of coupling faults and multiple fault types are regarded as network nodes respectively. The fault features are fused and extracted by graph convolution to achieve the classification of coupling faults. In this paper, dynamic vertexes are defined in data topology and the parameters of DIGNN classification model are optimized by changing the fault type of dynamic vertexes during training stage. The data is loaded into dynamic vertexes for classification and analysis during testing stage. The one-dimensional vibration data is converted into two-dimensional time-frequency domain data by wavelet transform making the input features of the model interpretable to reduce the uncertainty of model training. The data topology is then fed into DIGNN for fault classification, and GCN's node aggregation gives interpretability to each layer of network data processing. The method proposed in this paper can realize accurate diagnosis of independent faults on the data set, and can effectively judge the coupling mode of coupling faults, which is suitable for coupling fault analysis of mechanical equipment.

The extent of access to energy of displaced populations in settlements and camps in Africa is largely 14 unknown. A multitude of contextual factors, such as the location and the characteristics of housing, 15 the legal status, the socio-cultural background, and the availability of humanitarian and public ser- 16 vices impact the living conditions and the needed energy services. Limitations in accessing energy 17 services have direct, multilayered, and far-reaching implications, including impacts on health, nu- 18 trition, education, protection, and livelihood. The objective of this article is to contribute to a more 19 comprehensive overview of the current state of energy access in displacement contexts on the Afri- 20 can continent by identifying and utilizing existing data. After a screening of the vast and various 21 available information, setting up of a database, consolidating the gathered data as well as assessing 22 the quality through a quality assessment method, the currently available information is visualized 23 and discussed. Considerable differences in the access to electricity for displaced persons across the 24 countries are found. For both electricity and clean cooking, the availability for displaced persons 25 ranges from nearly no access at all up to an access rate of 100%. More strikingly, the results also 26 show that besides South Africa and countries in the Maghreb region, the access to both clean cook- 27 ing and electricity for displaced persons is very low. At the same time, the fragmented data availa- 28 bility, the poor data quality, and the questionable expediency of available data allows neither solid 29 theoretical conclusions nor planning of effective practical implementation measures. Novel inter- 30 disciplinary research, conceptual frameworks and indicators are needed for the purpose of compa- 31 rability and consistency. Future research has the potential to more comprehensively capture the 32 current state of access to energy in displacements contexts and in a next step to examine how energy 33 is interwoven in the lives of displaced people to derive a set of more detailed context-sensitive en- 34 ergy indicators. It is essential that the concerned persons, the displaced persons themselves are in- 35 cluded in the research in a meaningful way.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

In the past two decades, several floods have affected people and their properties in Burkina Faso, with the unprecedented flooding occurring in Ouagadougou in September 2009. So far, most studies have focused on Ouagadougou and surrounding localities and have paid little attention to other flood-prone regions in Burkina Faso. Specifically, there is a data and knowledge gap about the flood risk in the Haut-Bassins region, which in turn hampers the development of mitigation strategies and risk reduction measures in communities. This study demonstrates how data collected at the household level can be used to understand flood risk and its components at the village level in this data-scarce region. Using an indicator-based method, we analyze both flood risk and flood risk perception at the village level. Moreover, we determine the factors influencing flood risk perception at the household level using an ordered logit model. We find that 12 out of the 14 villages considered, experience high levels of flood risk. The management of runoff from the nearest urban areas and poorly designed civil engineering infrastructures, such as roads, were highlighted by the households as significant factors that increase their vulnerability. Hence, dependencies in space and between urban and rural areas may play a substantial role in modifying risk. The perceived flood risk consistently exceeds the estimated flood risk, with an insignificant positive correlation between both risk indices. Regression results indicate that flood risk perception is mainly influenced by informational and behavioral factors of the households. The findings of this study can provide valuable information to municipal and regional authorities involved in disaster risk management in the study area. Moreover, the method is transferable to other data-scarce regions

(1)Background:The purpose of the study was conducted to investigate the recovery of heart rate according to the performance level and rest interval conditions during 65%1RM bench press exercise;(2)Methods:The subjects of this study were eight healthy male college studentsin their 20 (years) attending University C. 1RM was measured before theexperiment, and the exercise sequence of six rest intervals (30sec, 1, 2, 3, 4,5min) was randomly selected and cross-distribution experiment. The experimental measurement was conducted a total of six times according to the rest interval condition (six conditions) once every 3 days to minimize the learning effect. The data was verified with repeated measures Two-way ANOVA and Contrast's repeated method was applied for post-comparison;(3)Results: First, the amount of exercise and the number of repetitions statistically substantially dropped (p<.001) as the number of sets rose, and a greater decline was shown when the rest periods got shorter. Second, the heart rate after exercise was increased significantly (p<.01) as the set progressed in the long rest interval conditions (4, 5min), and the heart rate after rest was increased statistically significantly (p<,05) as the set progressed in the short rest interval conditions (30sec, 1min). Third, the heart rate recovery rate (%) was able to perform more repetitions than in the short rest interval condition due to the relatively high physiological recovery of the neuromuscular and circulatory system under the long rest interval condition;(4)Conclusions: Therefore, according to the rest conditionduring the 65%1RM bench press exercise conducted in this study, the restinterval condition of 2~3min may be effective in improving muscular endurance,and the rest interval condition of 4~5min may be effective in improving muscular hypertrophy. As a result of this study, there was a significant difference in exercise performance (repetition) and physiological recovery depending on the rest interval condition according to the set progress during the same intensity resistance exercise. Through this, it is judged that it is possible to adjust the amount of exercise appropriate for the purpose of training by adjusting not only the intensity during resistance exercise but also the rest interval between sets.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

According to current forecasts, global heating is likely to exceed 2,8°C by the end of the century. This makes substantial adaptation measures necessary to secure a broad basis for livelihoods provision and the conservation of biodiversity. While the implementation of top-down and technocratic adaptation efforts is the majority, related adaptation shortcomings of socio-economic and ecological nature are becoming more and more apparent. Community-based adaptation (CBA) with its participatory, inclusive and needs-based bottom-up approach offers a promising and powerful alternative. This article uses a semi-systematic literature review approach to screen the current literature and identify core issues of CBA. Linking communality, locality, multidimensionality, power imbalances, transformative potential, localisation, the triad of adaptation metrics and adaptation with nature to corresponding potential actions for practical implementations provides a more holistic conceptualisation and broadens the horizons for further learnings, research and improved application.

The Automatic Dependent Surveillance-Broadcast (ADS-B) protocol stands as a cornerstone in modern aviation surveillance and Aircraft Traffic Control systems, integral to the NextGen project initiated by the US Department of Federal Aviation Administration (FAA) in 2005. ADS-B utilizes data links to autonomously broadcast Aircraft navigational and identification information to augment air transportation system capacity and safety. However, concerns regarding the protocol's security persist, particularly as its adoption expands. The unencrypted nature of transmitted aircraft data and the absence of robust authentication mechanisms render the protocol susceptible to exploitation by malicious actors. In this study, we comprehensively reviewed existing research in the field, identifying a crucial gap necessitating a holistic survey. Prior surveys have predominantly focused on specific aspects, such as vulnerabilities, attacks, or critiques of existing solutions. Our survey addresses this gap by thoroughly exploring the aviation system, providing readers with a nuanced understanding of ADS-B security. Utilizing a detailed SWOT analysis diagram, our paper delves into the vulnerabilities inherent in the ADS-B protocol outlines potential threats and scrutinizes various attack scenarios. We systematically categorize and analyze existing security solutions, considering cost-effectiveness, scalability, implementation complexity, and coverage against diverse attack vectors. Furthermore, we critically evaluate these solutions, elucidate ADS-B security requirements, discuss current challenges, and propose future research directions. This survey serves as a comprehensive resource for researchers and practitioners alike, shedding light on the multifaceted landscape of ADS-B security and paving the way for enhanced aviation system resilience in the face of evolving cybersecurity threats.

The unprecedented progress in Artificial Intelligence (AI), particularly in deep learning algorithms with ubiquitous internet connected smart devices, has created a high demand for AI computing on the edge devices. This review studied commercially available edge processors, and the processors that are still in industrial research stages. We categorized state-of-the-art edge processors based on the underlying architecture, such as dataflow, neuromorphic, and Processing in-Memory (PIM) architecture. The processors are analyzed based on their performance, chip area, energy efficiency, and application domains. The supported programming frameworks, model compression, data precision, and the CMOS fabrication process technology are discussed. Currently, most of the commercial edge processors utilize dataflow architectures. However, emerging non-von Neumann computing architectures have attracted the industry in recent years. Neuromorphic processors are highly efficient for performing computation with fewer synaptic operations, and several neuromorphic processors offer online training for secured and personalized AI applications. This review found that the PIM processors show significant energy efficiency and consume less power compared to dataflow and neuromorphic processors. The future direction of the industry would be to implement state-of-the-art deep learning algorithms in emerging non-Von Neumann computing paradigms for low power computing on the edge devices.

In this study, it was analyzed that the characteristics of ammonia and their effects on secondary particulate matter (PM) formation by region in Korea during 2020. The NH3 concentration was high in GJ (11.4 ppb) neighboring agricultural area followed by DJ (9.0 ppb) and SE (8.6 ppb) locating in the urban area. On the other hand, BI (2.6 ppb) and JI (4.5 ppb), which are background regions, were lower than other area. Seasonally, ammonia was high in spring and summer, and it generally increased when human activities are active. Therefore, it is believed that ammonia in the atmosphere changes depending on not only local emissions but also temperature-dependent phase distribution characteristics. For SE and GJ, regions with relatively high ammonia concentrations, the effect of ammonia on secondary PM formation was conducted. In both regions, the ammonium-to-sulfate mole ratio tended to increase with an ammonia or PM2.5 concentration increasing. It can be assumed that PM2.5 concentration increases as nitrates are formed under the ammonia sufficient condition. The adjusted gas ratio is generally greater than 4, indicating that there is a lot of free ammonia. Thus, it is estimated that reduction of ammonia would not effective to restrain the nitrate formation.

Understanding the dynamics of Organic Carbon mineralization is fundamental in forecasting biosphere to atmosphere Net Carbon Ecosystem Exchange (NEE). With this perspective, we developed 3D-CMCC-PSM, a new version of the hybrid Process Based Model 3D‐CMCC FEM where also heterotrophic respiration (R_h) is explicitly simulated. The aim was to quantify NEE as a forward problem, by subtracting Ecosystem Respiration (R_eco) to Gross Primary Productivity (GPP). To do so, we developed a simplification of the Soil Carbon dynamics routine proposed in DNDC [1]. The method calculates decomposition as a function of soil moisture, temperature, state of the organic compartments, and relative abundance of microbial pools. Given the pulse dynamics of soil respiration, we introduced modifications in some of the principal constitutive relations involved in phenology and littering sub-routines. We quantified the model structure related uncertainty in NEE, by running our training simulations over 1000 random parameter-sets extracted from parameters distributions expected from literature. 3D-CMCC-PSM predictability was tested on independent time series for 6 Fluxnet sites. The model resulted in daily and monthly estimations highly consistent with the observed time series. It showed lower predictability in Mediterranean ecosystems, suggesting that it may need further improvements in addressing evapotranspiration and water dynamics.

Pandemics, and other risk-related contexts, require dynamic changes in behavior as situations develop. Human behavior is influenced by both explicit (cognitive) and implicit (intuitive) factors. In this study, we used psychological distance as a lens to understand what influences our decision-making with regards to risk in the context of COVID-19. The study was based on the rationale that our relational needs are more concrete to us than the risk of the virus. First, we explored the impact of social-psychological distance on participants’ risk perceptions and behavioral willingness. As hypothesized, we found that close social relationships of agents promoted willingness to engage in risky behavior. In the second phase, we tested an intervention designed to increase the concreteness of information about virus transmission as a mechanism to mitigate the bias of social influence. We found that the concreteness intervention resulted in significantly reduced willingness to engage in risky behavior. As such, communications aimed at changing the behavior of citizens during times of increased risk or danger, should consider conceptually concrete messaging when communicating complex risk, and hence may provide a valuable tool in promoting health-related behavior.

We introduce the Symplectic Structure of Information Geometry based on Souriau’s Lie Group Thermodynamics model, with a covariant definition of Gibbs equilibrium via invariances through co-adjoint action of a group on its moment space, defining physical observables like energy, heat, and moment as pure geometrical objects. Using Geometric (Planck) Temperature of Souriau model and Symplectic cocycle notion, the Fisher metric is identified as a Souriau Geometric Heat Capacity. Souriau model is based on affine representation of Lie Group and Lie algebra that we compare with Koszul works on G/K homogeneous space and bijective correspondence between the set of G-invariant flat connections on G/K and the set of affine representations of the Lie algebra of G. In the framework of Lie Group Thermodynamics, an Euler-Poincaré equation is elaborated with respect to thermodynamic variables, and a new variational principal for thermodynamics is built through an invariant Poincaré-Cartan-Souriau integral. The Souriau-Fisher metric is linked to KKS (Kostant-Kirillov-Souriau) 2-form that associates a canonical homogeneous symplectic manifold to the co-adjoint orbits. We apply this model in the framework of Information Geometry for the action of an affine Group for exponentiel families, and provide some illustrations of use cases for multivariate Gaussian densities. Information Geometry is presented in the context of seminal work of Fréchet and his Clairaut-Legendre equation. Souriau model of Statistical Physics is validated as compatible with Balian gauge model of thermodynamics. We recall the precursor work of Casalis on affine group invariance for natural exponential families.

Wind energy is a kind of renewable energy with great potential for development. This study mainly investigated the application of shock waves generated by high-pressure gases (wind energy) for generating energy. In this study, we designed a new supersonic shock wave generator that can be reused without disassembling and assembling bolts and developed a supersonic shock wave monitoring system. This system monitored the velocity of the generated shock waves, which was Mach 3-5, and the output pressure was more than 100 times higher than the input pressure of the shock wave generator tank.Then, we developed a power generation system driven by supersonic shock waves based on the characteristics of the new shock wave generator, which can generate high-pressure and high-speed blast waves and can be reused. The shock wave generator can repeatedly generate high-pressure waves to drive the Tesla turbine and then the magnetic energy generator for power generation. We established a complete control process for power generation driven by shock waves by controlling the valve stem. The system can detect the tank pressure, output pressure, gas flow, rotation speed, voltage, and current during the control process for the performance analysis of power generation.

Drones have experienced rapid technological advancements, leading to the proliferation of small, low-cost, remotely controlled, and autonomous aerial vehicles with diverse applications, from package delivery to personal transportation. However, integrating these drones into the existing air traffic management (ATM) system poses significant challenges. The current ATM infrastructure, designed primarily for traditional manned aircraft, requires enhanced capacity, workforce, and cost-effectiveness to coordinate the large numbers of drones expected to operate at low altitudes in complex urban environments. To address this critical issue, this study aims to develop an intelligent, highly automated drone management system for integration into smart city transportation networks. The key objectives include: i) Developing a conceptual framework for an intelligent total transportation management system tailored for future smart cities, focusing on incorporating drone operations; ii) Designing an advanced air traffic management and flight control system capable of managing individual drones and drone swarms in complex urban environments; iii) Improving drone management methods by leveraging drone-following models and emerging technologies such as the Internet of Things (IoT) and the Internet of Drones (IoD); and iv) Investigating the landing processes and protocols for unmanned aerial vehicles (UAVs) to enable safe and efficient operations.

At the end of the dry season in early March to early April each year, extensive agricultural biomass waste burnings occur throughout insular mainland Southeast Asia. During this biomass burnings period, smoke aerosols blanket the whole regions and were transported and dispersed by predominant westerly and south westerly winds to southern China, Taiwan and as far southern Japan and the Philippines. The extensive and intense burnings coincided with some wildfires in the forests due to high temperature making the region one of the global hot spots of biomass fires. In this study, we focus on the effect of pollutants emitted from biomass burnings in March 2019 at the height of the burnings period to the exposed population and their health impact. The Weather Research Forecast- Chemistry (WRF-Chem) model was used to predict the PM2.5 concentration over the simulating domain and health impacts are then assessed on the exposed population in the four countries of Southeast Asia, namely Thailand, Laos, Cambodia and Vietnam. Using the health impact based on log-linear concentration response function and Integrated Exposure Response (IER), the results show that at the peak period of the burnings from 13 to 20 March 2019, Thailand experienced the highest impact, with an estimated 2170 premature deaths. Laos, Vietnam, and Cambodia followed, with estimated mortalities of 277, 565, and 314 deaths respectively. However, when considering the impact per head of population, Laos exhibited the highest impact, followed by Thailand, Cambodia, and Vietnam. The results highlight the significant health impact and associated economic cost of agricultural waste burnings in Southeast Asia at the end of the dry season. And hence policy makers should take these into account to design measures to reduce the negative impact of widespread burnings on exposed population in the region.

The World Health Organization estimates that every year air pollution kills seven million people worldwide. As it is expected that climate change will affect future air quality patterns, the full understanding of the links between air pollution and climate change, and how they affect human health, are challenges of future research. In this scope, a methodology to assess the air quality impacts on health was developed. The WRF-CAMx modelling framework was applied for the medium-term future climate (considering the SSP24.5 scenario) and for the recent past (considered as baseline). Following the WHO recommendations, mortality health indicators were used to estimate health impacts of long-term exposures. For that, the Aveiro Region, in Portugal, was considered as a case study. Future climate results indicate the occurrence of higher temperatures, and lower total precipitation. Despite that, improvements in the main pollutants’ concentrations, and consequently in the reduction of the related premature deaths are foreseen, mainly due to the reduction of pollutants emissions imposed by the European legislation for the upcoming years. The applied approach constitutes an added value in this research field, being crucial to anticipate the effects of climate change on air quality and evaluate their impacts on human health.

Buttonweed (Cotula coronopifolia) is native to South Africa but invasive in wetlands in Europe, North America, and Australasia, where it excludes native plants. Despite being dry-fruited, field studies suggest migratory waterbirds can disperse its seeds via gut passage (endozoochory), aiding its expansion. To explore the potential for endozoochory in different regions and habitats, we collected seeds from six populations in Spain, Sweden, and the UK. Germination was tested under different salinity levels (0, 5, 10, 15 g/L) and simulated gut passage treatments: scarification, acidification, or both. No germination occurred at 15 g/L. Higher salinity reduced and delayed germination, but full gut passage treatment increased germinability and accelerated germination. Scarification or acid treatment alone resulted in intermediate germination patterns. There were significant salinity x population and gut passage x population interactions on germinability. The acceleration effect of gut passage on germination was stronger at 5-10 g/L than at 0 g/L. This study highlights how migratory birds can facilitate the spread of alien plants introduced by humans. Non-classical endozoochory by waterbirds is an understudied mechanism for the long-distance dispersal of dry-fruited alien plants. Further research on C. coronopifolia, including population genetics, is necessary to understand dispersal mechanisms and facilitate management strategies.

The ever-increasing industrialization of certain areas of the planet combined with the simultaneous degradation of the natural environment are alarming phenomena, especially in the field of human health. The concentration of Particulate Matter with an aerodynamic diameter of 2.5μm (PM2.5) and 10μm (PM10), nitrogen oxides (NOx), carbon monoxide (CO), sulfur dioxide (SO2), and ozone (O3) needs constant monitoring, as they consist the main cause for many diseases. Based on the existence of statutory limits, by the World Health Organization (WHO), for the concentration of each of the aforementioned air pollutants, it is considered necessary to develop forecasting systems that will have the ability to correlate the current meteorological data with the concentrations of the above pollutants. In this work, the attempt to predict the air pollutants concentrations in the wider area of Beijing, China, is successfully carried out using artificial neural networks (ANNs) models. In the frame of the specific work, a significant number of ANNs was developed. For this purpose, an open-access meteorological and air pollution database was used. Finally, a statistical evaluation of the developed prognostic models was carried out. Results showed that ANNs present a re-markable prognostic ability in order to forecast the air pollution levels in an urban environment.

To analyze the combined response of ocular cyclotorsion and head tilt during body tilt and to interpret the physiologic role of those movements, each of the three subjects completed six different experiments of body tilt not fixating their head movements using a flight simulator, which consisted of combinations of three tilt angles (30, 45, and 60) and two visual conditions. Head tilt and ocular cyclotorsion of the right eye before, during, and after the tilt maneuver were recorded and analyzed by time sequence. In the active tilting phase, the right eye showed a stepladder pattern of multiple repeats of fast and slow cyclotorsion along with head tilt to obtain maximum visual information. During the stationary tilting phase, there occurred a small amount (mean, 2.3) of ocular cyclotorsion which was reciprocal to that of head tilt. The visual cue of body tilt through the central visual field induced a larger amount of head tilt but affected little ocular cyclotorsion. The maximum degree of ocular cyclotorsion during each experiment was 10.2 on average. In conclusion, the combined response of ocular cyclotorsion and head tilt develops during body tilt and it compromises the conflicting needs between binocular vision and gravitational orientation.

Particulate matter (PM) is one of the problems faced in environmental science. It has health effects on man and animals in both developed and developing countries. Research and efforts have been on it several years back. Policy statements and efforts have been published. This review paper is an added information on air pollution. In it, efforts were made in discussing these: classification, effects, methodology, case studies and source apportionment. It is hoped that this paper would contribute to existing knowledge on PM.

The author demonstrates a stable Lagrangian solid modeling method, tracking the interactions of solid mass particles rather than using a meshed grid. This numerical method avoids the problem of tensile instability often seen with smooth particle applied mechanics by having the solid particles apply stresses expected with Hooke's law, as opposed to using a smoothing function for neighboring solid particles. This method has been tested successfully with a bar in tension, compression, and shear, as well as a disk compressed into a flat plate, and the numerical model consistently matched the analytical Hooke's law as well as Hertz contact theory for all examples. The solid modeling numerical method was then built into a 2-D model of a pressure vessel, which was tested with liquid water particles under pressure and simulated with smoothed particle hydrodynamics. This simulation was stable, and demonstrated the feasibility of Lagrangian specification modeling for fluid–solid interactions.

The present study deals with the transplantation of mature Argan trees (Argania spinosa L. Skeels) and focuses on optimizing survival rates depending on the seasons, the type of shoot pruning applied to the trees and preconditioning treatments consisting of root pruningand watering for a few months before transplanting. So far, the transplantation of this species at the adult stage has not received enough attention in spite of its ecological and socio-economic importance for the regions where it thrives. The results obtained show that transplanting in summer, autumn and winter resulted in survival rates exceeding 50%. The Argan trees transplanted in spring hardly achieved 10% survival. However, the total cutback of the crown induced survival improvement that reached a rate greater than 70% for summer, autumn and winter, and 50% for spring. Watering alone or combined with root pruning for 6 months helped improve the recovery rate but only when carried out in autumn with transplantation in spring. On the other hand, when these pre-treatments were applied in the spring to transplant the trees in summer, the recovery rate was not improved.

Finding sustainable renewable energy sources for energy conversion and management is still an obscure topic. This paper presents a model-based simulation for an energy conversion system using piezoelectric energy harvester (PEH) technology. A dynamic mathematical model of a PEH device consists of a piezoelectric transducer, a controlled PWM rectifier, and a closed-loop buck boost converter is developed. A piezoelectric transducer converts mechanical vibrations from a wind force into an oscillating train of electrical charges. The sinewave peak-to-peak level relationship describes the changeable values of these charges, which depend on the severity of the wind vibration. The controlled PWM rectifier, in conjunction with a closed-loop buck-boost converter, converts this train of sinewave cycles into DC voltages. The control blocks of the closed-loop buck-boost converter use the perturbation and observation (P&O) algorithm based on maximum power point tracking (MPPT), which adapts the operational voltage of the piezoelectric source to deliver the maximum power to load and improves the PEHS output voltage stability. A simulation program is employed to perform mathematical analysis on various wind vibration scenarios, piezoelectric sources without PWM converters, and piezoelectric vibration sources connected to a closed-loop P&O converter. The crucial results of this paper demonstrate that the proposed dynamic PEHS model effectively feeds low-power electronic loads by directly adjusting the output voltage level to the set voltage, even under different vibration severity levels. As a result, the proposed PEHS dynamic model serves as a guideline for researchers in the development of self-powered sensors, which contributes to understanding sustainable energy alternatives.

This study investigated the efficiency of scale-propellers, typically used on small drones. A scale-propeller is accepted as having a diameter of 7 to 21 inches. The Ukraine War has demonstrated the utility of relatively small, low-cost first-person view (FPV) drones, which are attritable. This investigation outlines the development of a MATLAB optimisation code, based on minimum induced loss propeller theory, which calculates the optimal chord and twist distribution for a chosen propeller operating in known flight conditions. The MATLAB code includes a minimum Reynolds number functionality, which provides the option to alter the chord distribution to ensure the entire propeller is operating above a set threshold value of Reynolds (>100,000), as this has been found to be a transition point between low and high section lift-to-drag ratios. Additional functions allow plotting of torque and thrust distributions along the blade. The results have been validated on experimental data taken from an APC ‘Thin Electric’ 10” x 7” propeller, where it was found that both the chord and twist distributions were accurately modelled. The MATLAB code resulted in a 16% increase in the maximum propulsive efficiency. Further work will investigate a direct interface to SolidWorks to aid rapid propeller manufacturing capability.

The Vu Gia - Thu Bon River Basin (VG-TB) is confronting numerous challenges related to water security (WS), particularly in the face of the impacts of climate change. These challenges manifest in salinity intrusion, altered rainfall patterns, and reduced water supply in downstream areas. To assess the current state of water security in the basin, the study employed statistical analysis methods, Process Analysis Method (PAM), SMART, and Analytic Hierarchy Process (AHP) to develop a comprehensive Assessment Framework for Water Security (AFWS) in the VG-TB. The AFWS encompasses five key dimensions, 17 indicators, and 28 variables, aligning with the UN-Water definition of water security and addressing the Sustainable Development Goal 6 (SDG6) criteria for global water sustainability. It also adheres to the Asian Development Bank's (ADB) approach to water security assessment as outlined in the Asian Water Development Outlook (AWDO) reports. This allows for the computation of a comprehensive Water Security Index (WSI) for specific regions, serving as a foundation for decision-making and policy formulation aimed at enhancing water security in the context of climate change and facilitating sustainable basin development in the future.

Ambulatory heart rate (HR) monitors that acquire electrocardiogram (ECG) or/and photoplethysmographm (PPG) signals from the torso, wrists, or ears are notably less accurate in tasks associated with high levels of movement compared to clinical measurements. However, reliable estimation of HR can be obtained through data fusion from different sensors. These methods are especially suitable for multimodal hearable devices, where heart rate can be tracked from different modalities, including electrical ECG, optical PPG, and sounds (heart tones). Combined information from different modalities can compensate for single source limitations. In this paper, we evaluate the possible application of data fusion methods in hearables. We assess data fusion for heart rate estimation from simultaneous in-ear ECG and in-ear PPG, recorded on eight subjects while performing 5-minute sitting and walking tasks. Our findings show that data fusion methods provide a similar level of mean absolute error as the best single-source heart rate estimation but with much lower intra-subject variability, especially during walking activities. We conclude that data fusion methods provide more robust HR estimation than a single cardiovascular signal. These methods can enhance the performance of wearable devices, especially multimodal hearables, in heart rate tracking during physical activity.

We developed an artificial neural network as an air quality model and estimated the scope of the impact of climate change on future (until 2064) summertime trends of hourly Ozone (O3) concentrations at an urban air quality station in Tehran, Iran. Our developed scenarios assume that present-time emissions conditions of O3 precursors will remain constant in the future. Therefore, only the impact of climate change on future O3 concentrations is investigated in this study. GCM projections indicate more favorable climate conditions for O3 formation over the study area in the future: the surface temperature increases over all months of the year, solar radiation increases, and precipitation decreases in future summers, and summertime daily maximum temperature increases about 1.2 ∘C to 3 ∘C until 2064. In the scenario based on present-time O3 conditions in 2012 summer without any axceedances, the summertime exceedance days of 8-hr O3 standard are projected to increase in the future by about 4.2 days in the short term and about 12.3 days in the mid-term. Similarly, in the scenario based on present-time O3 conditions in 2010 summer with 58 days of exceedance from 8-hr O3 standard, exceedances are projected to increase about 4.5 days in the short term and about 14.1 days in the mid-term. Moreover, the number of Unhealthy and Very Unhealthy days in 8-hr AQI is also projected to increase based on pollution scenarios of both summers.

A dynamic impact test was performed on as-rolled AZ31 alloy with gradient microstructure under various strains. The microstructural evolution and mechanical properties were systematically investigated. As the strain rate gradually increases, an increasing number of twins are formed, facilitating dynamic recrystallization (DRX), and the mechanical properties are also gradually improved as well. The microstructure becomes heterogeneous at higher strain rates, but the peak stress decreases. The impact process results in significantly higher performance due to microstructural refinement, work hardening by dislocations and precipitates. In addition, both the adiabatic shear band and the adjacent crack experience a temperature rise that exceeds the recrystallization temperature of the alloy. This observation also explains the presence of ultrafine recrystallized grains within the adiabatic shear band and the appearance of molten metal around the crack.

The agronomic characteristics of Cenchrus purpureus were assessed through a randomized block experimental design with seven accessions (Taiwan grass, King grass, Elephant grass, Merkeron, CT-115, Purpule grass and Maralfalfa) as treatments and four replications research was carried out at the Instituto Tecnológico Superior de Tantoyuca, in 2019 and 2020, under rainfed conditions. Sowing density was established at 36 tillers in 25 m2. Green and dry matter yield, daily rates of dry matter accumulation in leaves, leaf/stem ratio, height, leaf area index and cutting frequency were assessed. Rainfall amount, temperature, relative humidity and global radiation levels were recorded to assess their effect on the evaluated variables. One-way ANOVA and multivariate analysis techniques, such as multiple linear regression (MLR), Clustering, and Principal component analysis (PCA) with the Statistica V7 software, were used. The leaf area index was greatest (p < 0.05) on the dry season. Green and dry matter yield were greatest in Maralfalfa (p < 0.05). Variation in the results is attributed to weather phenomena; nonetheless, Elephant grass and Maralfalfa showed the highest yields. Quality parameters must be evaluated to identify those grasses with the best attributes.

In the 21st century, climate change and its consequences are getting more serious. The changes in temperature and precipitation alter the run-off conditions, subsequently influencing the channel processes of rivers. The study aims to analyse the hydrological changes of a small, sub-alpine river (Rába River, Central Europe) and the bank erosional processes since the 1950s. The bank erosion was determined based on topographical maps, aerial photographs, and RTK–GPS surveys. Short (2–3 days) floods were common between 1950–1980, and low stages occurred in 65–81% of a year. However, in the 21st century, extreme regimes developed, as record-high, flashy floods alter with long low stages (91–96% of a year). The bank erosion shows a cyclic temporal pattern, gradually increasing until it reaches a high value (4.1–4.9 m/y), followed by a limited erosional rate (2.2–2.8 m/y). However, the magnitude of the bank erosion is decreasing. It could be explained by (1) the lower transport capacity of the more common low stages and (2) the seasonal shift of the flood waves, appearing in the vegetational period when the riparian vegetation can more effectively protect the banks from erosion.

This study presents PlanteSaine, a novel mobile application powered by Artificial Intelligence (AI) models explicitly designed for maize, tomato, and onion farmers in Burkina Faso. Agriculture in Burkina Faso, like many developing nations, faces substantial challenges from plant pests and diseases, posing threats to both food security and economic stability. PlanteSaine addresses these challenges by offering a comprehensive solution that provides farmers with real-time identification of pests and diseases. Farmers capture images of affected plants with their smartphones, and PlanteSaine's AI system analyzes these images to provide accurate diagnoses. The application's offline functionality ensures accessibility even in remote areas with limited internet connectivity, while its messaging feature facilitates communication with agricultural authorities for guidance and support. Additionally, PlanteSaine includes an emergency alert mechanism to notify farmers about pest and disease outbreaks, enhancing their preparedness to deal with these threats. An AI-driven framework, featuring an image feature extraction phase with EfficientNetB3 and an artificial neural network (ANN) classifier, was developed and integrated into PlanteSaine. The evaluation of PlanteSaine demonstrates its superior performance compared to baseline models, showcasing its effectiveness in accurately detecting diseases and pests across maize, tomato, and onion crops. Overall, this study highlights the potential of PlanteSaine to revolutionize agricultural technology in Burkina Faso and beyond. Leveraging AI and mobile computing, PlanteSaine provides farmers with accessible and reliable pest and disease management tools, ultimately contributing to sustainable farming practices and enhancing food security. The success of PlanteSaine underscores the importance of interdisciplinary approaches in addressing pressing challenges in global agriculture

This paper, from the perspective of Mode 3 of knowledge production, takes the important carrier of knowledge, scientific research papers, as the research object. The mainstream databases (SCIE and SSCI) are chosen as the data sources. Firstly, bibliometric methods are applied to analyze the cooperation status among the main bodies of paper production, including authors and their affiliated institutions, countries, and disciplines; secondly, the Analytic Hierarchy Process (AHP) is used to construct a comprehensive evaluation model for the state of research cooperation in carbon neutrality. Based on the evaluation model, the cooperation characteristics of different disciplinary fields and the relationship between paper cooperation status and high-impact research papers are comparatively analyzed. At the same time, an analysis is conducted on the support from the government, the sponsorship from enterprises, and the participation of the public in the process of paper production. Finally, some suggestions are put forward on how to build an innovative ecosystem for carbon neutrality research from the perspective of Mode 3 of knowledge production.

Autosomal dominant polycystic kidney disease (ADPKD) is an inherited disorder characterized by renal tubular cystic dilatations. The cysts can develop anywhere along the nephron and over time the cystic dilatation lead to kidney enlargement. On the other hand, the cysts begin to reduce the number of functional nephrons as a consequence of cystic expansion that further contributes to the decline in renal function over the years. The pressure exerted by the dilated cysts lead to compensatory mechanisms that further contribute to the decline in renal function. These structural changes are responsible of glomerular hyperfiltration states, albuminuria, proteinuria, and haematuria. However, the presentation of ADPKD varies in children from a completely asymptomatic child with incidental ultrasound detection of cysts to a rapidly progressive disease. There have been reports of early onset of ADPKD in children younger than 2 years that showed a more rapid decline in renal function. ADPKD is caused by mutation in PKD1 and PKD2 genes. Today, the PKD1 gene mutation seems to account for up to 85% of the cases worldwide, and it is associated with worse renal outcomes. Individuals with PKD2 gene mutation seem to present a milder form of the disease, with a more delayed onset of end stage kidney disease. The cardinal sign of ADPKD is the presence of renal cysts during renal ultrasound. The current guidelines provide the clinicians the recommendations for genetic testing in children with a positive family history. Given that the vast majority of children with ADPKD present with normal or supra normal kidney function we explored the glomerular filtration rates dynamics and the renal ultrasound adjusted percentiles. 14 out of 16 patients had kidney percentile over 90%. The gene mutations were equally distributed among our cohort. In addition, we compared the modified Schwartz formula to the quadratic equation after adjusting the serum creatinine measurements. It seems that even though children with ADPKD have enlarged kidneys, the renal function is more likely normal or near normal when the quadratic estimation of glomerular filtration rate is used (qGFR tended to be lower, 111.95 ± 12.43 ml/min/1.73m2 compared to Schwartz eGFR 126.28 ± 33.07ml/min/1.73m2, p=0.14). Also, when the quadratic equation was employed, not even a patient reached the glomerular hyperfiltration thresholds. The quadratic formula showed that glomerular filtration rates are linear or slightly decreasing after 1-year of follow-up (Quadratic ΔeGFR=0.32±5.78ml/min/1.73m2) as opposed to Schwartz formula that can falsely classify children in a hyperfiltration state ΔeGFR=7.51±19.46ml/min/1.73m2), p=0.019.

The definition of UTC in 1972 balanced the needs of the time and frequency community for a universal time scale that was traceable to the definition of frequency in the SI system of units with the needs of the astronomical community for a time scale that was closely linked to UT1, a time scale related to the rotation of Earth. The balance between these two considerations has changed very significantly since 1972, and there is widespread agreement that the method of relating UTC to UT1 should be changed by increasing the maximum tolerance between the two scales to more than the current limit of 0.9 s. I propose to realize this decision by means of an algorithmic adjustment process based on the variation in the length of the day over the previous centuries. I use these historical data to extrapolate the length of the day for a century into the future, and to compute a periodic rate adjustment to UTC based on this extrapolation. The adjustment process will not use time steps. The magnitude of the periodic rate adjustment will be re-considered every century, but the basic adjustment algorithm will not change. I suggest a maximum tolerance between UT1 and UTC that is large enough to absorb the irregular and unpredictable variations in the length of the day with respect to the long-term average increase in this value but plays no role in determining the parameters of the adjustment process that is proposed. I also propose that the adjustment be implemented at 12 UTC on 1 January since that is closest to a universal holiday in all time zones.

In this paper we present a city-scale (possibly global) air pollution network made of low-cost sensors for particulate matter concentration in the air. The components of presented system are based on our research and experience from previous studies focused on air quality instruments and sensors for addressing urban air pollution. Sensor nodes are produced locally and distributed over a city of Sarajevo, Bosnia and Herzegovina. The system collects, calibrates and displays particulate metal concentrations in real-time. In comparison to the available measurements from governmental institutions, our system demonstrated good agreement of measured parameters, with several advantages including: higher resolution in space and time, lower costs, both horizontal and vertical measurements and many more. One of the capabilities of the system is the real-time air pollution city map with animations. By installing multiple sensor nodes over a slope (cable car), we receive vertical measurements of temperature, humidity and particulate matter concentration in real time, which gives a valuable insight into the dynamics of temperature inversion episodes and air pollution below the inversion layer.

Panel data of our interest consist of a moderate number of panels, while the panels contain a small number of observations. An estimator of common breaks in panel means without a boundary issue for this kind of scenario is proposed. In particular, the novel estimator is able to detect a common break point even when the change happens immediately after the first time point or just before the last observation period. Another advantage of the elaborated change point estimator is that it results in the last observation in situations with no structural breaks. The consistency of the change point estimator in panel data is established. The results are illustrated through a simulation study. As a by-product of the developed estimation technique, a theoretical utilization for correlation structure estimation, hypothesis testing, and bootstrapping in panel data is demonstrated. A practical application to non-life insurance is presented as well.

Acute and chronic respiratory diseases impose a significant economic and health burden. Distal small airway assessment requires invasive procedures such as a bronchoscopy and bronchoalveolar lavage. The Particles in Exhaled Air (PExA) device provides a non-invasive means of assessing small airways; it captures distal airway particles sized around 0.5-7m and contains particles of respiratory tract lining fluid (RTLF) that originate during airway closure and opening. The PExA device can measure particle count and mass according to particle size. Subsequent capture of particles in a thin membrane enables application of various analytical methods to assess a broad range of biomolecules including phospholipids, proteins, inflammatory profile, and other metabolites to characterise inflammation and diseases processes such as asthma, chronic obstructive pulmonary disease, acute respiratory distress syndrome, lung cancer, and more recently acute infections such as COVID-19. PExA analysis provides a promising alternative to traditional investigative methods in the assessment, diagnosis, and management of respiratory conditions. By evaluating specific biomarkers in the RTLF associated with airway inflammation, PExA may offer a more accurate and comprehensive understanding of the molecular-level changes in the small airways of patients with acute and chronic lung diseases.

Background: Bioaerosol can represent a danger to the health. During SARS-CoV-2 pandemic, portable devices were used in different environments and considered a valuable prevention tool. This study has evaluated the effectiveness of the air treatment device “AEROK 1.0” in reducing microbial, particulate and pollen airborne contamination indoors, during normal activity. Methods: In an administrative room, airborne microbial contamination was measured using active (DUOSAS 360 and MD8) and passive sampling; a particle counter was used to evaluate particle concentrations; a Hirst-type pollen trap was used to assess airborne pollen and Alternaria spores. Statistical analysis was performed using SPSS 26.0; p values <0.05 were considered statistically significant. Results: The airborne bacterial contamination assessed by the two different samplers decreased by 55.54% and 69.13%, respectively. The airborne bacterial contamination assessed by passive sampling decreased by 44.16%. For fungi, the reduction was 38.7% by active sampling. Airborne particles (diameters ≥ 1.0, 2.0 μm) and the ratio of indoor/outdoor concentrations of total pollen and Alternaria spp spores significantly decreased. Conclusions: The results highlight the effectiveness of AEROK 1.0 in reducing airborne contamination. The approach carried out represents a contribution to the definition of a standardized model for evaluating the effectiveness of this type of devices.

This bibliographic study addresses key aspects related to fishing, product safety, and climate change in the Adriatic Sea region. The examination of product safety focuses on the assessment of contaminants originating from human activities such as industry, mining, agriculture, and household waste disposal. The contamination of the aquatic environment has emerged as a pressing global concern, extending to the Adriatic subbasin. Aquatic organisms, including fish, are prone to accumulating pollutants directly from polluted water sources and indirectly through the food web. The bio-accumulation of potentially hazardous substances, particularly heavy metals, pesticides, PCBs, PAHs, and antibiotic resistance in aquatic organisms, poses a significant threat to human health. Climate change effects will deplete our seafood supply in terms of quantity and safety owing to negative consequences such as higher levels of pollution, parasites, viruses, infections, acidification, and toxicities such as shellfish poisoning. Global food safety strategies should be developed to reduce greenhouse gas emissions and promote environmentally friendly technology, which indirectly affects seafood quality and microbiological safety, especially for Adriatic Sea, which is part of the Mediterranean Sea, characterized by the most polluted waters in the world.

The working environment of mining electric locomotives is wet and muddy coal mine 1 roadway. There may be idling or slipping between the wheels and rails of mining electric locomotives 2 due to low friction between the wheel and rail and insufficient utilization of creep rate. Therefore, it 3 is necessary to control the creep rate within a reasonable range. In this paper, the autonomous control 4 algorithm for mining electric locomotives based on improved ε-greedy is theoretically proven to be 5 convergent and effective firstly. Secondly, after analyzing the contact state between the wheel and rail 6 under wet and slippery road conditions, it was concluded that the value of creep rate is an important 7 factor affecting the autonomous driving of mining electric locomotives. Therefore, the autonomous 8 control method for mining electric locomotives based on creep control is proposed in this paper. 9 Finally, the effectiveness of the proposed method was verified through simulation. The problem of 10 wheel slipping and idling caused by insufficient friction of mining electric locomotives in coal mining 11 environments is effectively suppressed. Autonomous operation of vehicles with optimal driving 12 efficiency can be achieved through quantitative control and utilization of the creep rate between 13 wheels and rails

Air pollution is a critical issue impacting urban environments, leading to severe health problems and environmental degradation. This comprehensive review examines the potential of green systems—specifically green walls, active green walls, and urban greenery systems—to mitigate atmospheric pollutants such as particulate matter (PM), volatile organic compounds (VOCs), and carbon dioxide (CO2). By systematically analyzing 44 recent studies, the review highlights the pollutant capture efficiency of various green technologies and plant species in both indoor and outdoor settings. Active green walls, particularly those utilizing plant species such as Chlorophytum comosum and Sansevieria trifasciata, were found to be highly effective, with VOC reduction efficiencies up to 96.34%, PM reductions by 65.42%, and CO2 reduction rates reaching 4.8% under optimal conditions. The review identifies key strengths in current research, including diverse experimental setups and the use of sophisticated measurement techniques, but also notes significant limitations such as variability in experimental conditions and a lack of long-term performance data. The study underscores the importance of proper maintenance to sustain green systems' efficacy and highlights the potential issue of pollutant resuspension, which remains under-researched. Practical implications for urban planning are discussed, advocating for the integration of effective green systems into urban infrastructure to enhance air quality and public health. Recommendations for future research include the need for standardized metrics, long-term studies, economic feasibility analyses, and real-world validation of simulation models to better understand and optimize green systems for urban air pollution mitigation.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

The recent mountain pine beetle outbreaks have caused widespread mortality among lodgepole pine trees in western North America, resulting in a reduced population of surviving trees. While previous studies have focused on the cascading impacts of these outbreaks on the physiology and growth of the surviving trees, there remains a need for a comprehensive study into the interactions among various physiological traits and the growth in post-outbreak stands. Specifically, the relationship between chemical (primarily terpenes) and anatomical (mainly resin ducts) defences, as well as the allocation of non-structural carbohydrates (NSCs) to support these defence modalities, is poorly understood. To address these gaps, we conducted a field survey of surviving lodgepole pine trees in post-mountain pine beetle outbreak stands in western Canada. Our retrospective analysis targeted to determine correlations between the post-outbreak concentrations of monoterpenes, diterpenes, and NSCs in the phloem, and the historical resin duct characteristics and growth traits before and after the outbreak. We detected strong correlations between post-outbreak concentrations of monoterpenes and historical resin duct characteristics, suggesting a possible link between these two defence modalities. Additionally, we found a positive relationship between NSCs and the total concentrations of monoterpenes and diterpenes, suggesting that NSCs likely influence the production of these terpenes in lodgepole pine. Furthermore, historical tree growth patterns showed strong positive correlations with many individual monoterpenes and diterpenes. Interestingly, while surviving trees had enhanced anatomical defences after the outbreak, their growth patterns did not vary before and after the outbreak conditions. The complexity of these relationships emphasizes the dynamics of post-outbreak stand dynamics and resource allocation in lodgepole pine forests, highlighting the need for further research. These findings contribute to a broader understanding of conifer defenses and their coordinated responses to forest insect outbreaks, with implications for forest management and conservation strategies.

One challenging problem is the representation of three-dimensional datasets that vary with time. These datasets can be though as a cloud of points that gradually deforms. But point-wise variations lack of information about the overall deformation pattern, and more importantly, about the extreme deformation locations inside the cloud. The present article applies a technique in computational mechanics to derive the strain-rate state of a time-dependent and three-dimensional data distribution, by which one can characterize its main trends of shift. Indeed, the tensorial analysis methodology is able to determine the global deformation rates in the entire dataset. With the use of this technique, one can characterize the significant fluctuations in a reduced multivariate description of an urban system and identify the possible causes of those changes: calculating the strain-rate state of a PCA-based multivariate description of an urban system, we are able to describe the clustering and divergence patterns between the districts of the city and to characterize the temporal rate in which those variations happen.

Several studies have reported a relationship between autonomic dysfunction　 during tasks and Internet addiction. Changes within 24 h regarding heart rate variability (HRV) may be a more sensitive indicator than short term observations. We evaluated the influence of excessive Internet usage on HRV using a 24 h electrocardiogram (ECG) and examined acute changes during computer game tasks. A total 13 high school students and 22 young adults were recruited, and divided into excessive Internet user and non- excessive user groups based on Internet addiction test scores. The ECG was recorded continuously for 24 h by a wearable sensor and during two computer games (the Iowa gambling task and each participant’s preferred game) using a standard type ECG system. Multiple psychometric tests were also conducted. The excessive Internet user group exhibited clinically significant depressive symptoms, and higher self-reported scores for anxiety, impulsivity, autistic tendencies, and sleep problems than the non- excessive internet user group. There were weak differences within the 24 h high-frequency (HF) band power between two groups. During the Iowa gambling task, younger participants exhibited a reduced HF response, which may be related to weaker top- down self- regulatory mechanisms.

Subnational governments play a key role responding to climate change risks in terms of policy strategies and instruments. This article analyzes how Brazilian municipal and state governments have developed and implemented public policies to mitigate and to adapt to climate change risks. We surveyed all cities’ and states’ climate policies within the country. The methodological approach includes five main points of analysis: 1. mitigation targets and intentions; 2. adaptation actions; 3. stakeholders’ participation; 4. policy implementation; 5. participation in networks related to climate change. Our results suggest that even though subnational climate policies in Brazil are isolated initiatives within the national context, they play an important role responding to climate change risks in different scales and levels. The strongest Brazilian policies with both mitigation and adaptation actions counted on previous mobilization for the climate issue involving different stakeholders from several segments of the society. These governments have also participated in transnational cooperation networks related to climate change.

It is concerning that Cameroon's urban centers are experiencing an alarming rise in air pollution as a result of urbanization, population growth, industrial activity, and transportation emissions. We examined the causes, health impacts, research methodology, case studies, and government measures to address the urgent issue of air pollution in Cameroon's urban regions. We have emphasized how Cameroon's air pollution levels have significantly increased as a result of causes like population expansion, urbanization, industrial emissions, and automobile exhaust A thorough discussion of the negative health impacts of extended exposure to air pollution is included, with special attention to the sensitivity of the old and young. These effects include respiratory disorders, cardiovascular ailments, and early mortality. We emphasized the pressing need for all-encompassing strategies to address air pollution, such as increased public awareness campaigns, stronger emissions regulations, the development of renewable energy sources, and better waste management. The techniques employed in studies on air pollution, like as epidemiological research and air quality monitoring, are also explained to provide light on the unique health dangers that Cameroonian urban dwellers must contend with. We emphasized in our conclusion the significance of joint efforts by legislators, medical professionals, and the general people to reduce air pollution and protect public health in Cameroon in order to create a cleaner and healthier future. In order to protect public health in the future, it is imperative that Cameroon's air pollution be addressed.

Museums are called to respond to contemporary challenges and contribute to the formation of more progressive societies. One of the major challenges of our time is climate change and museums could construct cocreated narratives around climate and implement targeted actions for the audiences through their sensorial and affective experiences. More specifically, Geology and Palaeontology museums are repositories of knowledge on geoheritage and geoconservation, recognized for their scientific, pedagogical, cultural and recreational values. The educational potential of geological and paleontological exhibits could be used in informal education activities regarding the climate emergency. Taking the above into consideration, this study focuses on both the creation and evaluation of an educational program for the Natural History Museum of Arsakeio Campus at Psychicko.

This article utilizes the Canny edge extraction algorithm based on contour curvature and the cross-correlation template matching algorithm to extensively study the impact of high-repetition-rate CO2 pulsed Laser on the target extraction and tracking performance of the infrared imaging detector. It establishes a quantified dazzling pattern for lasers on infrared imaging systems. By conducting laser dazzling and damage experiments, a detailed analysis of the normalized correlation between target and dazzling images is performed to quantitatively describe laser dazzling effects. Simultaneously, an evaluation system, including target distance and laser power evaluation factors, is established to determine the dazzling level and whether the target is recognizable. The research results reveal that laser power and target position are crucial factors affecting the detection performance of infrared imaging-guided weapon systems under laser dazzling. Different laser powers are required to successfully interfere with the recognition algorithm of infrared imaging-guided weapons at different distances. And laser dazzling will produce a lot of false edge information, which seriously affects the performance of pattern recognition algorithm. In laser damage experiments, the detector experienced functional damage, with a quarter of the image displaying as completely black. The energy density threshold required for functional damage to the detector is approximately 3 J/cm2. The dazzling assessment conclusions also apply to evaluating damage results. Finally, the proposed evaluation formula aligns with experimental results, objectively reflecting the actual impact of laser dazzling on the target extraction and tracking performance of infrared imaging systems. This study provides an in-depth and accurate analysis for understanding the influence of lasers on the performance of infrared imaging-guided weapons.

Melioidosis is an endemic infectious disease caused by Burkholderia pseudomallei bacteria, which contaminates soil and water. To better understand the environmental changes that have contributed to melioidosis outbreaks, this study used spatiotemporal analyses to clarify the distribution pattern of melioidosis and the relationship between melioidosis morbidity rate and local environmental indicators (land surface temperature, normalised difference vegetation index, normalised difference water index) and rainfall. A retrospective study was conducted from January 2013 to December 2022, covering data from 219 sub-districts, with each exhibiting varying morbidity rate of melioidosis on a monthly basis. Spatial autocorrelation was determined using local Moran’s I, and the relationship between melioidosis morbidity rate and the environmental indicators was evaluated using geographically weighted Poisson regression. The results revealed clustered spatiotemporal patterns of melioidosis morbidity rate across sub-districts, with hotspots predominantly observed in the northern region. Furthermore, we observed a range of coefficients for the environmental indicators, varying from negative to positive, which provided insights into their relative contributions to melioidosis in each local area and month. These findings highlight the presence of spatial heterogeneity driven by environmental indicators and underscore the importance of public health offices implementing targeted monitoring and surveillance strategies for melioidosis in different locations.

The extensive use of polypropylene (PP) in various industries has heightened interest in devel-oping efficient methods for recycling and optimising its mixtures. This study focuses on formu-lating predictive models for the Melt Flow Rate (MFR) and shear viscosity of PP blends. The in-vestigation involved characterising various grades, including virgin homopolymers, copolymers, and post-consumer recyclates, in accordance with ISO 1133 standards. The research examined both binary and ternary blends, utilising traditional mixing rules and symbolic regression to predict rheological properties. High accuracy was achieved with the Arrhenius and Cragoe models, at-taining R² values over 0.99. Symbolic regression further enhanced these models, offering signif-icant improvements. To mitigate overfitting, empirical noise and variable swapping were in-troduced, increasing the models' robustness and generalisability. The results demonstrated that the developed models could reliably predict MFR and shear viscosity, providing a valuable tool for improving the quality and consistency of PP mixtures. These advancements support the de-velopment of recycling technologies and sustainable practices in the polymer industry by opti-mising processing and enhancing the use of recycled materials.

The enterprise software sector is experiencing a significant transformation driven by rapid technological progress and evolving business needs. An effective release management process is crucial for the solution providers and customers, as they incorporate the principles of Industry 4.0 and 5.0. With the growing dependence on software solutions and services, ensuring their quality, reliability, and security is highly necessary. The release management process incorporates strategic planning, regression testing, accurate deployment, and continuous monitoring of software updates. However, the rapid advancements in artificial intelligence (AI) and machine learning (ML) create a unique challenge to the release management process. The existing research needs to address the necessary adaptations for Industry 5.0, mainly in product-based software organizations, to the release management process without a change management system. After working with several software solution stakeholders, based on the responses from SaaS project stakeholders, we have presented a revised software release readiness workflow by incorporating a change management module. The preliminary result based on data over a limited period of time indicates that the revised workflow has the potential to improve the management of slippage, particularly by more effectively addressing NFR-related issues, thereby resulting in more predictable and reliable release cycles.

As the demand of heating and air conditioning is increasing day by day due to getting a comfortable life, for that reason, the market for heat pump and air conditioning systems or both, is seeing a steady increase in low global warming potential. All researchers on heat pump and air conditioning systems are searching for environmentally friendly refrigerants. However, a significant number of contemporary refrigerants (HCFCs) have the potential to cause global warming and ozone depletion, such as those found in heat pump air conditioning systems. Using more environmentally friendly refrigerants, including hydrocarbon and blend refrigerant mixtures, is one way to lower GWP and Ozone depletion potential. This study examines the performance of several alternative refrigerants, including R32, R134A, R410A, R22, and R290. In order to examine the performance of R290, theoretical and simulation results are compared on various refrigerants while taking into account a number of performance parameters, including the refrigerant energy efficiency ratio, mass flow rate, coefficient of performance, cooling capacity, and compressor work for one ton of refrigeration (1TR) air conditioners. One player with a very low GWP is R290. However, the only drawback is that it can catch fire and is hazardous to use in split-type commercial heat pump air conditioning applications. The environmental and thermo physical properties of HC-290 are significantly better than those of other materials, according to theoretical and simulation studies utilizing Cool Pack software, hence it is a viable replacement.

Large water bodies such as the Laurentian Great Lakes have significant influences on local and regional climate through their unique physical features. Due to the coarse spatial resolution of general circulation models (GCMs), the Great Lakes are geometrically ignored in most GCMs. Thus, the dynamical downscaling technique serves as a necessary and feasible solution to bridge the gap. The Weather Research and Forecasting model (WRF) with an updated lake scheme is employed to downscale from a GCM, GFDL-CM3. The WRF-Lake’s performance is evaluated against observations, the GCM, as well as 23 other GCMs. Results show that the coupled air-lake model, with a fine spatial resolution and realistic lake bathymetries, reproduced a more reasonable spatiotemporal climatology than GCMs, as well as the lake-induced characteristics that were missed in GCMs. With lakes present, the seasonal variability of air temperature was reduced in WRF-Lake relative to GFDL-CM3, especially in summer. A reduced air temperature trend, about 4.5 °C/100 year in the 21st century, was projected in WRF-Lake. The seasonal evolutions of lake surface temperature and lake ice coverage were well captured by the lake model. The lake surface temperature was projected to be warming by 3.5-4 °C and the lake ice diminishing by 58.9% - 86%. Those results brought by the WRF-Lake model suggest that a fine resolution of the topography and the incorporation of the lake-atmosphere interactions are crucial to improve the understanding of the climate and climate change in the Great Lakes region.

Introduction: Subtalar Arthroereisis (STA) is a surgical intervention for pediatric flexible flatfoot (PFF), primarily targeting hindfoot alignment by limiting excessive subtalar eversion. However, its effects on forefoot parameters remain underexplored. This study aims to investigate radiological changes following STA in pediatric patients. Materials and Methods: A retrospective analysis was conducted on consecutive patients treated with STA for PFF. First ray-related angles, including Hallux Valgus Angle (HVA) and Inter-Metatarsal Angle (IMA), alongside hindfoot radiological parameters such as Meary, Calcaneal Pitch, and Costa Bartani angles, were assessed. Subgroup analysis by gender was performed, and correlations between demographic and pre-operative radiological parameters were examined. Results: Forty-one patients (81 feet) with a mean age of 11.6 years were included, with a mean follow-up duration of 6.4 months. No significant differences were observed in first ray-related an-gles pre- and post-operatively, with mean IMA changing from 7.97° to 7.18° and mean HV angles from 9.51° to 8.66°. Noteworthy improvements were seen in flat foot angles, including Meary, Calcaneal Pitch, and Costa Bartani angles, postoperatively. Age subgroup analysis revealed similar trends in IMA and HVA changes between Group A (operated before peak growth) and Group B (operated later). Higher preoperative angles tended to improve, while lower preoperative IMA and HVA tended to worsen postoperatively, all remaining within normal ranges. Conclusion: STA showed positive radiological outcomes for PFF treatment, while negligible changes in first ray-related angles were observed. Age subgroup analysis indicated similar trends regardless of operation timing. Higher preoperative angles tended to improve, while lower preoperative angles tended to worsen postoperatively, despite all falling within non-pathological ranges. Further re-search is warranted to confirm this correlation.

In this study the effects of three different main preparatory tillage operations [ploughing at 0.4 m (P40) and 0.20 m (P20) depth and minimum tillage at 0.20 m depth (MT) each of them carried out at two different soil water contents (WC) [low, 58% (LH) and high, 80% (HH) of field capacity] were investigated. The results obtained in this research show high values of soil strength in term of Penetration resistance (CI) and shear strength (SS) particularly in deeper soil layers at lower water content. Fossil-fuel energy requirements both for P40 LH and P20 LH were 25 and 35% higher with respect to the HH treatments and tractor slip were very high (P40 LH = 32.4%) with respect to the P40 HH treatment (16%). Therefore soil water content had significantly influenced tractor performance during soil ploughing, particularly at 0.40 m depth while MT was not influenced at all. A significant correlation between grain yield and soil penetration resistance was found highlighting how soil strength may be good indicator of its productivity. Obtained results during these field tests allowed considering MT and P20 treatments more suitable for this type of soil in climate change scenarios.

In this work, satellite data from the Clouds and Earth’s Radiant Energy System (CERES) and Moderate Resolution Imaging Spectroradiometer (MODIS) instruments is analyzed to determine how the global absorbed sunlight and global entropy generation rate have changed during the time period from 2002 to 2023. The data is used to test hypotheses derived from the Maximum Power Principle (MPP) and Maximum Entropy Production Principle (MEP) about the evolution of earth’s surface and atmosphere. The results indicate that the amount of absorbed sunlight has increased over the last 20 years but rising surface temperatures have caused the entropy generation rate to remain approximately constant despite that decrease in albedo. The results are simpler to explain using the MPP but do not completely rule out the MEP. Given the acceptance of the MPP or MEP, some extensions and nuances are discussed.

Background: Anxiety disorders can be both an independent risk factor of many somatic conditions and the cause of complications of various organic disorders leading to poor prognosis. Objectives: The purpose of this study is to compare the heart rate variability (HRV) recorded both during the day and at night in patients with anxiety disorders and healthy individuals. Methods: The study was conducted on fifty consecutive outpatients with anxiety disorders who participated in intensive group psychotherapy. The diagnosis was made according to DSM-IV-TR criteria using the PSE-10 questionnaire. Out of 50 patients under study, 17 were diagnosed with panic disorder (PD) and 21 with generalized anxiety disorder (GAD). The control group consisted of 40 healthy people. The resulting three groups were compared in terms of circadian HRV using the Oxford Medilog Suprima Holter System. Results: The HRV analysis showed the nocturnal falls in the time and frequency parameters related to parasympathetic activity (rMSSD, pNN50, HF). The most unfavourable alterations were observed in the PD group, which comprised the disappearance of day vs. night amplitude of the majority of HRV parameters. Hence, the PD group was particularly susceptible to the arrhythmic events. It was noticeable that nocturnal vagotonia in the PD group was significantly lower as compared with the GAD and control group. Conclusions: The innovative aspect of the present study was to find a distinct profile of HRV with regard to the types of anxiety disorders because of the existing considerable differences between the nature of PD and GAD.

Smartwatches are one of the most relevant fitness trends of the past two decades, and they collect increasing amounts of health and movement data. The accuracy of these data may be questionable and requires further investigation. Therefore, the aim of the present study is to validate smartwatches for use in triathlon training. Ten different smartwatches were tested for accuracy in measuring heart rate, distance (via global navigation satellite systems, GNSS), swim stroke rates and the number of swim laps in a 50 m Olympic-size pool. The optical heart rate measurement function of each smartwatch was compared to that of a chest strap. Thirty participants (15 females, 15 males) ran five 3-minute intervals on a motorised treadmill to evaluate the accuracy of the heart rate measurements. Moreover, for each smartwatch, running und cycling distance tracking was tested over six runs of 4,000 m on a 400 m tartan stadium track, six hilly outdoor runs over 3.4 km, and four repetitions of a 36.8 km road bike course, respectively. Three swimming protocols ranging from 200 m to 400 m were performed in triplicate in a 50 m Olympic-size pool, evaluating tracked distance and detected number of strokes. The mean absolute percentage errors (MAPEs) for the average heart rate measurements varied between 3.1% and 8.3%, with the coefficient of determination ranging from 0.22 to 0.79. MAPE results ranged from 0.8% to 12.1% for the 4,000 m run on the 400 m track, from 0.2% to 7.5% for the 3.4 km outdoor run, and from 0.0% to 4.2% for the 36.8 km bike ride. For the swimming tests, in contrast, the deviations from the true distance varied greatly, starting at a 0.0% MAPE for the 400 m freestyle and reaching 91.7% for the 200 m medley with style changes every 25 m. In summary, for some of the smartwatches, the measurement results deviated substantially from the true values. Measurements taken while road cycling over longer distances with only a few curves were in relative terms more accurate than for outdoor runs and even more accurate than for the 400 m track. In the swimming exercises, the accuracy of the measured distances was severely deteriorated by the medley changes among the majority of the smartwatches. Altogether, the results of this study should help in assessing the accuracy and thus suitability of smartwatches for general triathlon training.

The Food and Drug Administration’s 2011 Process Validation Guidance and International Council for Harmonization Quality Guidelines recommend continued process verification (CPV) as a mandatory requirement for pharmaceutical, biopharmaceutical, and other regulated industries. As a part of product life cycle management, after process characterization in stage 1 and process qualification and validation in stage-2, CPV is performed as stage-3 validation during commercial manufacturing. CPV ensures that the process continues to remain within a validated state. CPV requires the collection and analysis of data related to critical quality attributes, critical material attributes, and critical process parameters on a minimum basis. Data is then used to elucidate process control regarding the capability to meet predefined specifications and stability via statistical process control tools. In statistical process control, control charts and Nelson rules are commonly used throughout the industry to monitor and trend data to ensure that a process remains in control. In the control chart, the mean value is taken as the center line, and 3σ limits are placed on either side of the center line. In CPV, manufactured lots are summarized, trended, and discussed at a cross-functional level at pre-defined intervals (either weekly, bi-weekly, or even monthly) based on the batch run rate. A cross-functional team assesses details regarding 1) violation frequency, 2) statistical strength of the signal, 3) violation magnitude and its impact on process or quality, and 4) any potential root causes for out-of-expectation or out-of-trend signals. The cross-functional team must analyze whether any signal identified by the control chart is reliable and must determine whether corrective action should be taken and justify the decision in the CPV meeting minutes based on statistical strength and reliability of the signal. However, basic control charts are susceptible to false alarms and nuisance alarms. Therefore, it is imperative to understand the assumptions behind control charts and the inherent false alarm rates for different Nelson rules. In this article, the authors have detailed the assumptions behind the usage of control charts, the rate of false alarms for different Nelson rules, the impact of skewness and kurtosis of a data distribution on the false alarm rate, and methods for optimizing control chart design by reducing false alarm rates and nuisance signals.

Climate change has altered the frequency and severity of extreme weather, which can affect vegetation condition and habitat quality for wildlife. Declines in vegetation productivity during droughts and heatwaves can negatively impact animals that depend on vegetation for water and nutrition. The ability to detect such effects on habitat suitability can reveal refugia, which can be prioritised for protection to improve threatened species conservation. We used the normalised difference vegetation index (NDVI) to look at relationships between vegetation productivity and the presence of koalas (Phascolarctos cinereus) in potential habitat throughout much of their range. Using a large, long-term koala presence dataset, we tested the hypothesis that locations where koalas had been observed would exhibit higher NDVI values than a random, representative sample from the same vegetation group (i.e. woodlands, open forests or tall open forests). We also identified the minimum NDVI threshold at which koalas occurred across time for each vegetation group and compared these to the minimum NDVI values observed across potential koala habitat before and during the millennium drought; one of the worst recorded in Australia. Additionally, we investigated whether vegetation above the minimum NDVI thresholds was significantly closer to perennial water than unsuitable vegetation. We found that koalas tend to occur at locations exhibiting higher NDVI than average for all vegetation groups. We also found that 49% of all vegetation groups maintained a minimum NDVI above the koalas’ NDVI threshold before drought, equating to 190,227 km2, which declined to 166,746 km2 during drought (a 12% reduction). We also found that unsuitable vegetation tended to occur farther from perennial water than suitable vegetation for some vegetation groups. Areas that remained above the NDVI thresholds during the drought should be considered potential refugia for populations during an event of similar magnitude and could indicate future core habitat extent.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

Nowadays, the growing concern about improving thermal comfort in textiles, asphalt pavements and buildings has stimulated research into phase change materials (PCMs). However, the incorporation of PCMs directly causes mechanical impacts. Therefore, this study herein reported focuses on designing coaxial phase change fibres using commercial cellulose acetate (CA) or recycled CA obtained from cotton fabrics (CAt) as a coating and polyethylene glycol (PEG) 2000 as a core. The phase change fibres (PCF) were produced by wet spinning, varying the parameters: (i) CA concentration, molecular weight and source (virgin versus recycled); and (ii) PEG concentration and ejection. For phase change recycled fibres (PCFt), PEG concentration and ejection were varied. The fibres were assessed for their optical, chemical, thermal and mechanical properties. Bright-field microscopy images and Scanning Electron Microscopy (SEM) micrographs proved the coaxial structure. Fourier Transform Infrared spectroscopy (FTIR) confirmed the presence of PEG in the core. Thermogravimetric Analysis (TGA) proved the ability of PCFs to tolerate high temperatures. Differential Scanning Calorimetry (DSC) attested to the presence of PEG2000 peaks, since their melting points were close to those of virgin PEG2000, with a slight change in the PCFs and PCFts caused by the protective sheath of CA and CAt.

During the last decade, Bangladesh has been experienced a significant climatic anomalies which lead to an increase in magnitude and frequency of various climate relate extreme events. Climate scientists substantiate that global temperature and precipitation pattern is expected to change, which may result in consequential impact on agriculture, livelihood, and ecosystem. Bangladesh is therefore likely to face substantial challenges in the coming decades. In order to adequately understand this complex, dynamic phenomena, Analyzing historical Climate change scenarios as well as projecting its future trends is a great concern for researcher. This study aims to analyzes/ historical climatic data from (1901-2020), and predict future temperature and precipitation patterns in Bangladesh using CMIP6 data. Data used in this study (Observed data is from CRU TS 4.05 and future data is from CMIP6) have been acquired from WorldClim v2.1. Various methods including correlation, regression, standard deviation, correlation matrix, percentiles, cell statistics, and IDW interpolation were performed to analyze the trends, variability and spatial patterns of temperature and rainfall. This study revealed that Over the historical study period (1901-2020) Bangladesh has been experienced a significant warming trend with an average increase in temperature 2°C and with annual decline of the total precipitation 607.26 mm along with a shift towards drier conditions despite weak correlation with hotter years. Projected climate models represents that Bangladesh minimum temperature is expected to increase from 1°C to 4.4°C as well as maximum temperatures from 1°C to 4.1°C by 2100. Moreover, projected precipitation is expected to increase by 480.38 mm, with the biggest rises during monsoon months. Regional variations in temperature and precipitation are again expected, with the Southeast (SE) likely experiencing the most significant warming and the Northeast (NE) seeing the most substantial increase in precipitation.

Currently, one of the main challenges is the mitigation of the effects of climate change on the agricultural sector. Conventional agriculture, with the intensive use of herbicides and pesticides to control weeds and pests, and the improper use of mineral fertilizers, contributes to climate change by causing increased greenhouse gases and groundwater pollution. Therefore, more innovative technologies must be used to overcome these problems. One possible solution is nanotechnology, which has the potential to revolutionize the conventional agricultural system. Active nanoparticles can be used both as a direct source of micronutrients and as a delivery platform for bioactive agrochemicals to improve crop growth, yield and quality. The use of nanoparticle formulations, including nanopesticides, nanoherbicides, nano-fertilizers and nano-emulsions, has been extensively studied to improve crop health and shelf life of agricultural products. Comprehensive knowledge of the interactions between plants and nanoparticles opens up new opportunities to improve cropping practices through the enhancement of properties such as disease resistance, crop yield, and nutrient use. The main objective of this review is to analyze the main effects of climate change on conventional agricultural practices, such as the use of pesticides, herbicides and fertilizers. It also focuses on how the introduction of nanoparticles into conventional practices can improve the efficiency of chemical pest control and crop nutrition. Finally, this review examines in depth the last 10 years (2014-2024) of scientific literature regarding the use of nanoparticles in agriculture to mitigate the effects of climate change.

In the Internet of Things (IoT) era, Mobile Edge Computing (MEC) significantly enhances the efficiency of smart devices but is limited by battery life issues. Wireless Power Transfer (WPT) addresses this issue by providing a stable energy supply. However, effectively managing overall energy consumption remains a critical and under-addressed aspect for ensuring the network’s sustainable operation and growth. In this paper, we consider a WPT-MEC network wit user cooperation to migrate the double near-far effect for the mobile node (MD) far from the base station. We formulate the problem of maximizing long-term computation rates under a power consumption constraint as a multi-stage stochastic optimization (MSSO) problem. This approach is tailored for a sustainable WPT-MEC network, considering the dynamic and varying MEC network environment, including randomness in task arrivals and fluctuating channels. We introduce a virtual queue to transform the time-average energy constraint into a queue stability problem. Using the Lyapunov optimization technique, we decouple the stochastic optimization problem into a deterministic problem for each time slot, which can be further transformed into a convex problem and solved efficiently. Our proposed algorithm works efficiently online without requiring further system information. Rigorous mathematical analysis shows that our algorithm achieves O(1/V),O(V) trade-off between computation rate and queues stability. Extensive simulation results demonstrate that our proposed algorithm outperforms baseline schemes, achieving approximately 4% enhancement while maintain the queues stability.

The study examines projected changes in dry- and wet-spell probabilities in West Africa using a Markov chain approach. Four simulations of regional climate models from the CORDEX-Africa program were used to analyze projected changes in intraseasonal variability. The results show an increase in the probability of having a dry day, a dry day preceding a wet day and a dry day preceding a dry day, and a decrease in the probability of wet days in the Sahel region under anthropogenic forcing scenarios RCP4.5 and RCP8.5. The decrease in wet days is stronger in the far future and under the RCP8.5 scenario (up to -30%). The study also finds that the probability of consecutive dry days (lasting at least 7 days and 10 days) is expected to increase in the Western Sahel, the Central Sahel, and the Sudanian Area under both scenarios, with stronger increases in the RCP8.5 scenario. In contrast, the decrease is expected over the Guinea Coast, with the changes more important under the RCP4.5. These changes in dry- and wet-spell probabilities are important for water management decisions and risk reduction in the energy and agricultural sectors. The study also highlights the need for decision-makers to implement mitigation and adaptation policies to minimize the adverse effects of climate change.

The climate change constitutes nowadays an enormous global threat for human health and environmental sustainability. The expanding world population and the increased global needs for food production have an important negative impact upon environment. Diet can link human health with environmental sustainability. Food production systems are closely related to anthropogenic greenhouse gas emissions and the aggravation of climate change, and current western type, animal-based, dietary patterns may lead to adverse environmental footprints. In the present narrative review, we address the interconnection of the Mediterranean diet (MD) with climate change and sustainability. MD is a highly recommended dietary intervention for the prevention and management of various endocrine and cardiometabolic diseases. Beyond its evidence-based, health-promoting effects, it also has beneficial environmental impact, reducing greenhouse gas emissions and enhancing biodiversity, food security and sustainability. Based on the evidence reviewed herein, MD should be incorporated within the framework of a “One Health” model, which involves the improvement not only of human health but also of planetary health and food system sustainability. Our review aims to provide a stimulus for health pro-fessionals to strongly recommend the implementation of MD under the current pressure of climate change, despite all barriers, targeting both human health preservation and the planetary well-being.

In order to solve the problem of large eddy current loss and high temperature rise caused by large amount of permanent magnet, a new type of combined magnetic pole permanent magnet motor is proposed in this paper. The sinusoidal distribution subdomain model of non-uniform air gap rotor is established by using Laplace equation, and the analytical expression of eddy current loss of rotor in uniform air-gap and non-uniform air-gap is derived. The effect of rotor eccentricity on eddy current loss is obtained. According to the characteristics of distributed winding of non-uniform air gap combined pole permanent magnet motor, equivalent treatment is performed to obtain the equivalent thermal conductivity, so as to establish equivalent thermal network model of motor, calculate the temperature value of each component of the motor, and verify the correctness of the thermal network model through the method of magnetothermal bidirectional coupling. Finally, an experimental platform is set up to carry out temperature rise experiments on the two prototypes respectively. Experimental results show that the non-uniform air-gap rotor structure can effectively reduce the rotor eddy current loss and motor temperature rise, and also verify the accuracy of the analytical model calculation results.

Bicycle transport stands at the forefront of sustainable mobility initiatives, a cornerstone of European Union policy. While support for cycling is crucial, its advancement hinges upon the presence of high-quality, secure infrastructure for cyclists. Safety emerges as a paramount concern, influencing the viability of cycling as a mode of transportation, yet its perception varies among user demographics. Considering this, this article endeavours to examine and contrast cycling infrastructure across various European nations, alongside analysing statistics pertaining to fatal traffic accidents involving cyclists. In our paper, we have chosen the Netherlands as a representative of building quality cycling infrastructure with many years of experience, and two countries that are developing conditions for cyclists, Slovakia and Poland. We have applied a correlation between the length of the transport infrastructure and the number of cyclists killed. The findings point to the substantial correlation between the quality of cycling infrastructure and the incidence of accidents. This correlation underscores the pressing need for robust infrastructure development and safety measures to bolster cycling as a safe and viable transportation option. We have employed the Shapiro-Wilk test for normal distribution to verify the input data and process the Pearson correlation to investigate the correlation between cycling infrastructure and road accident fatalities of cyclists.

Few studies have examined the dietary protein intake and sources in combination with the longitudinal changes in brain structure markers. Our study aimed to examine the association between dietary protein intake and different sources of dietary protein with the longitudinal rate of change in brain structural markers. A total of 2723 and 2679 participants from the UK Biobank were included in the analysis. The relative and absolute amounts of dietary protein intake were calculated through a 24-hour dietary recall questionnaire. The longitudinal change rates of brain structural biomarkers were computed using two waves of brain imaging data. We utilized multiple linear regression to examine the association between dietary protein and different sources and the longitudinal changes in brain structural biomarkers. Restrictive cubic splines were used to explore nonlinear relationships, and stratified and sensitivity analyses were conducted. Increasing the proportion of animal protein in dietary protein intake is associated with a slower reduction in the total hippocampus volume (THV, β: -0.02524, P&lt;0.05), left hippocampus volume (LHV, β: -0.02435, P&lt;0.01) and right hippocampus volume (RHV, β: -0.02544, P&lt;0.05).Higher intake of animal protein relative to plant protein is linked to a lower atrophy rate in THV (β: -0.01249, P&lt;0.05) and LHV (β: -0.01173, P&lt;0.05) and RHV (β: -0.01193, P&lt;0.05). Individuals with higher intake of seafood exhibit lower longitudinal rate of change in HV compared to those with no consume (THV, β: -0.004514; P&lt;0.05; RHV, β: -0.005527, P&lt;0.05). In subgroup and sensitivity analyses, there was not a significantly alteration. A moderate increase in the intake and proportion of animal protein in the diet, especially from seafood, is associated with a lower longitudinal change rate in hippocampus volume.

With the exponential growth of internet usage and mobile devices, the volume of user behavior data has surged, offering significant opportunities and challenges for businesses. This paper explores user behavior analysis in the context of big data, highlighting its pivotal role in driving innovation and strategic decision-making. We begin by discussing the importance of user behavior data and reviewing technological advancements such as machine learning, natural language processing, and data mining that enable deep insights into user behavior. Through a case study on linguistic analysis in livestreaming e-commerce, we demonstrate how text-mining techniques can correlate linguistic characteristics with sales performance, providing actionable marketing insights. We further explore the broader business applications, including personalized recommendations, user portraits, product design, and strategic decision-making. Technical and ethical challenges, such as data integration, privacy concerns, and algorithmic bias, are also addressed. The paper concludes with a discussion on future trends, such as AI and ML advancements, edge computing, IoT proliferation, and ethical AI frameworks, poised to shape user behavior analysis. Our findings underscore the transformative potential of user behavior data in enhancing business operations and user experiences, providing recommendations for future research focused on real-time analytics, privacy-preserving techniques, and ethical implications of data-driven decisions.

This article examines the impact of climate change on the hydrometeorological state of some lakes and reservoirs in the Akmola and North Kazakhstan regions. Time series with values of various climate parameters for the period 1986-2023 are used for the climate analysis; the reliability of the results was assessed using the Fisher criteria. Hydrometric indicators were studied using the ArcGIG program. Using GIS to spatially analyze water climate data, 8-channel satellite images from 1995 to 2023 were used. During the study, it was found that the area of the main lakes has undergone changes.

One of the factors in the mobility of a nation's economy is the stock exchange which plays a decisive role in sustainable economic development. Accordingly, and for the special place of the stock exchange in the economy, we decided to investigate the relationship between the interest and exchange rates and the Tehran stock exchange dividend and price index (TEDPIX). Using the autoregressive distributed lag method, the present study is conducted utilizing the annual data over the period of 1991 to 2020. The results indicate that the exchange rate has a positive long-run relationship with the TEDPIX, but no statistically significant relationship was found between the TEDPIX and the interest rate. Furthermore, the results of the estimation of the error correction model show that 30.786% of the disequilibrium in each period is adjusted to the long-run equilibrium.

Warsaw is among European cities with the worst atmospheric air quality, mainly due to very high pollution emitted by the residential sector and road traffic. This results in high concentrations of particulate matter and nitrogen oxides, often exceeding WHO standards. The paper discusses the current and expected effects of actions taken by the Warsaw authorities, to significantly improve air quality in the city. The Clean Air Program currently implemented mainly involves the reduction, and ultimately the total elimination, of coal combustion in all heat sources of the municipal sector, which is identified in numerous publications as the main source of air quality degradation in cities. The program's goal, which timeframe covers the years 2018-2029, is a definite reduction in particulate pollution. The second part of the remedial activities, covering the years 2024-2034, mainly concerns the reduction of nitrogen oxide pollution, the main source of which is urban road traffic. In the latter case, the expected effects of introducing Low-Emission Zone (launched July 2024) in the city center are considered. According to the project, the zone's implementation will consist of five two-year stages, in which the car emission limits will gradually tighten. The paper compares the effectiveness of two being considered versions, differing in size zones.

This study investigates the impacts of climate change policies on businesses across various sectors, aiming to understand how these regulations affect operational, financial, and strategic aspects of business management. Utilizing a mixed-methods approach, data was collected from 500 businesses through surveys and interviews, encompassing a wide range of industries, sizes, and geographic locations. The findings reveal a complex landscape where 30% of businesses report positive impacts, primarily in the renewable energy and technology sectors, citing increased demand for green products and improvements in energy efficiency. Conversely, 45% of businesses, especially from manufacturing and agriculture, experience negative impacts, including increased operational costs and regulatory compliance challenges. Notwithstanding, a significant majority of businesses are committed to enhancing their sustainability practices, viewing climate change policies as an opportunity for innovation and long-term growth. The study highlights the nuanced effects of climate change policies, emphasizing the need for sector-specific support measures to alleviate financial and operational burdens on negatively impacted businesses. Moreover, it points to a broader shift towards sustainability within the business community, suggesting that climate policies, despite their varied impacts, are driving significant changes in business strategies towards environmental stewardship.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

(1) Background: The aim of the work was to characterize the climatic evolution and change based on the Multi Criteria Classification through the dynamics of bioclimatic indices in viticulture across Italy and its regional administrative boundaries, focusing on latitudes and elevations. (2) Methods: The impact of climate change on viticulture in Italy was analysed and spatialized with reference to historical data from 1991 to 2021 and to the Future Scenarios up to 2080 assumed by SSP2-4.5 and SSP5-8.5, taking into account 13 GCMs. (3) Results: The bioclimatic indices have all shown a significant trend in the historical period, with an increase in temperature and a decrease in precipitation, reflecting their effects on the entire Italian territory with respect to HI, up to 44°N for CI and up to 46°N for DI, regardless of altitude. The Future Scenarios highlighted a shift towards the warmer classes of the two temperature-based indices (HI and CI) for both SSPs, especially for altitudes up to 900 m a.s.l.. The DI-based classification based on DI remained relatively stable in Italy over time, although DI values will become increasingly negative in the near future. (4) Conclusions: The climate in Italy is warming, especially in the south and in the coastal regions. By 2080, more areas will be “Very Hot” with “Warm Nights.” Drought will also increase and have a negative impact on viticulture. The importance of higher latitudes and altitudes in mitigating the effects of climate change justifies the continuing trend towards the relocation of vineyards as a medium-term solution and as an alternative to targeted cultivation methods that must be adopted in the short-term to safeguard the suitability of an area to quality viticulture.

Understanding the interrelationships between land use, climate change, and regional water yield is critical for effective water resource management and ecosystem protection. However, comprehensive insights into how water yield evolves under different land use scenarios and climate change remain elusive. This study employs the Integrated Valuation of Ecosystem Services and Trade-offs (InVEST) models, Patch-generating Land Use Simulation (PLUS) model, and Geodetector within a unified framework to evaluate the dynamics of land use, water yield, and their relationships with various factors (meteorological, social, economic, etc.). To forecast the Land Use/Cover Change (LUCC) pattern of the Yellow River Basin by 2030, three scenarios were considered: economic development priority (Scenario1), ecological development priority(Scenario2), and cropland development priority(Scenario3). Climate change scenarios were constructed using CMIP6 data, representing low stress (SSP119), medium stress (SSP245), and high stress (SSP585) conditions. The results show the following: (1) From 2000 to 2020, cropland was predominant in the Yellow River Basin, Henan Province, with significant land conversion to impervious land (construction land) and forest land; (2) Water yield changes during this period were primarily influenced by meteorological factors, with land use changes having negligible impact; (3) By 2030, the water yield of Scenario1 is highest among different land use scenarios, marginally surpassing ecological development priority by 0.5%; (4) Climate scenarios reveal significant disparities, with SSP126 yielding 67% higher water production than SSP245, driven predominantly by precipitation; (5) Geodetector analysis identifies precipitation as the most influential single factor, with significant interactions among meteorological and socio-economic factors. These findings offer valuable insights for policymakers and researchers in formulating land use and water resource management strategies.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r&gt;0.90) and peri-urban (HWM, HWA, r&gt;0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

Malignant lymphoma is an unusual form of gallbladder neoplasm. Almost all of these tumors are diffuse large B-cell lymphomas or mucosa-associated lymphoid tissue-type lymphomas. Herein, we report a rare case of a gallbladder Burkitt’s lymphoma (BL) in a child living with HIV. As far as we are concerned, this is the first report in the pediatric population and in an individual living with HIV. The patient attended the Federal Hospital of Lagoa, Rio de Janeiro, Brazil, underwent cholecystectomy and the postoperative pathological analysis of the gallbladder revealed a diagnosis of BL. Also, HIV serology was performed and returned positive. She was transferred to the Martagão Gesteira Institute of Pediatrics and Childcare for oncological treatment, dying from sepsis and disease progression about 18 months later. Patient did not undergo ART/cART. Previous cases of gallbladder BL were analyzed to characterize the clinicopathological features. BL can occur in the gallbladder both in the context of HIV infection and in the pediatric population. Biopsy is mandatory in cases with suggestive findings of lymphoma, and an early diagnosis can change the course of the disease. Furthermore, the case highlights the importance of an early initiation of ART/cART in people living with HIV (PLWH).

This research analyzes the phenomenon of the reduction of urban green spaces in the post-socialist city. Belgrade was selected as a post-socialist city of the former Yugoslavia. The article analyses the views of urban planners on the reasons for the reduction of urban green areas in the post-socialist city based on semi-structured interviews with representative samples for urban areas. This result research confirms the hypothesis that post-socialist city planning reduces urban green areas due to the lack of new mechanisms in documents for the planning of urban green space. The concept of sustainability should connect and balance the skills of urban planners and focus on how urban planners develop and apply standards and protect them in market-democratic systems. In other words, a new mechanism of post-socialist city planning implies a balance between the private and public sectors. In the planning document, urban planners should find a common denominator between the public interest, citizens, investors, and spheres determined by the sustainable principles of the development. City institutions should provide opportunities for the application of those standards. With the new approach, planning would imply work in the service of citizens in the concepts of a sustainable and green city.