In this study, a basic study was performed to analyze the seasonal temperature status of a research room in the Global Environment Research Building where ceiling-embedded indoor units are installed to study the room temperature status of the building as well as to improve its thermal environment. In addition, a direction for improvement of the indoor thermal environment in the winter was proposed through a CFD (computational fluid dynamics) simulation and was proven by an additional experiment. Through the results of this study, it appeared that if the ceiling-embedded indoor unit was installed in the small indoor space without considering the thermal vulnerability of its perimeter boundary, the air temperature of the upper part was greatly different from that of the bottom part in the winter. Hence, in this study, as a means to improve it, convectors were installed to minimize the effect of the external thermal environment and angle-controllable air flowing fans were installed to mitigate the stratification distribution. With such result, it was intended to present the essential data for improvement of the thermal environment as well as conservation of heating energy in the winter for buildings by reviewing the use of the ceiling-embedded indoor unit in the future.

The development effect of water flooding in ultra-low permeability reservoir was poor due to its poor physical property and high shale content, the experimental study of air flooding which help to complement producing energy was carried out. Based on the Accelerating Rate Calorimeter experimental results, the crude oil of N block in L oilfield can produce low-temperature oxidation reaction, which was the basic condition of air flooding. Three groups of experiment natural cylinder core were designed for oil displacement, water flooding and air flooding were used respectively, and the relationship of differential pressure, oil recovery, injection capacity with injection volume was investigated. It has been showed on the result that the recovery efficiency improved sharply than water flooding, the effect of depressurization and augmented injection was obvious, and the air displacement was validation.

The application of smartphone-based color evaluation of passive sampling devices for gases has only been sparsely reported. The present review aims to compile available publications with respect to the configuration of the passive samplers, conditions of smartphone photographing, analytical procedure for color detection and quantification (including calibration processes), and their application to different target gases. The performance of the methods - whenever available - is presented regarding the analytical specifications selectivity, sensitivity, and limit of detection in comparison with other color evaluation methods of passive samplers. Practical aspects like requirements of instrumentation and ease of use will be outlined in view of the potential employment in education and citizen science projects. In one section of the review the inconsistent terminology of passive and diffusive sampling is discussed in order to clarify the distinction of information obtained from the uptake of the passive samplers between gas-phase concentration and the accumulated deposition flux of gaseous analytes. Colorimetric gas sensors are included in the review when applied in passive sampling configurations and evaluation is performed with smartphone-based color evaluation. Differences in the analytical procedures employed after the passive sampling step and prior to the detection of the colored compounds are also presented.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

We introduce the Symplectic Structure of Information Geometry based on Souriau’s Lie Group Thermodynamics model, with a covariant definition of Gibbs equilibrium via invariances through co-adjoint action of a group on its moment space, defining physical observables like energy, heat, and moment as pure geometrical objects. Using Geometric (Planck) Temperature of Souriau model and Symplectic cocycle notion, the Fisher metric is identified as a Souriau Geometric Heat Capacity. Souriau model is based on affine representation of Lie Group and Lie algebra that we compare with Koszul works on G/K homogeneous space and bijective correspondence between the set of G-invariant flat connections on G/K and the set of affine representations of the Lie algebra of G. In the framework of Lie Group Thermodynamics, an Euler-Poincaré equation is elaborated with respect to thermodynamic variables, and a new variational principal for thermodynamics is built through an invariant Poincaré-Cartan-Souriau integral. The Souriau-Fisher metric is linked to KKS (Kostant-Kirillov-Souriau) 2-form that associates a canonical homogeneous symplectic manifold to the co-adjoint orbits. We apply this model in the framework of Information Geometry for the action of an affine Group for exponentiel families, and provide some illustrations of use cases for multivariate Gaussian densities. Information Geometry is presented in the context of seminal work of Fréchet and his Clairaut-Legendre equation. Souriau model of Statistical Physics is validated as compatible with Balian gauge model of thermodynamics. We recall the precursor work of Casalis on affine group invariance for natural exponential families.

The author demonstrates a stable Lagrangian solid modeling method, tracking the interactions of solid mass particles rather than using a meshed grid. This numerical method avoids the problem of tensile instability often seen with smooth particle applied mechanics by having the solid particles apply stresses expected with Hooke's law, as opposed to using a smoothing function for neighboring solid particles. This method has been tested successfully with a bar in tension, compression, and shear, as well as a disk compressed into a flat plate, and the numerical model consistently matched the analytical Hooke's law as well as Hertz contact theory for all examples. The solid modeling numerical method was then built into a 2-D model of a pressure vessel, which was tested with liquid water particles under pressure and simulated with smoothed particle hydrodynamics. This simulation was stable, and demonstrated the feasibility of Lagrangian specification modeling for fluid–solid interactions.

Particulate matter (PM) is one of the problems faced in environmental science. It has health effects on man and animals in both developed and developing countries. Research and efforts have been on it several years back. Policy statements and efforts have been published. This review paper is an added information on air pollution. In it, efforts were made in discussing these: classification, effects, methodology, case studies and source apportionment. It is hoped that this paper would contribute to existing knowledge on PM.

The microscopic pore structure of tight sandstone reservoir significantly influences the characteris-tics of CO2 flooding after water flooding. The research was conducted using various techniques such as casting thin sections, high pressure mercury injection, scanning electron microscopy, Nu-clear magnetic resonance (NMR) testing, and a self-designed high-temperatures and high-pressures microscopic visualization displacement system. Three type cores with different pore structures were selected for the flooding experiments and the microscopic visualization displace-ment experiments, including CO2 immiscible flooding, near-miscible flooding, and miscible flood-ing after the conventional water flooding. The characteristics of CO2 flooding and the residual oil distribution after water flooding were quantitatively analyzed and evaluated. The results show that: (1) During the water flooding process, the oil produced from type I and type III samples mainly comes from large and some medium pores. Oil utilization of all pores is significant for type II samples. The physical properties and pore types have a greater impact on water flooding. Type I and II samples are more suitable for near-miscible flooding after water flooding. Type III samples are more suitable for miscible flooding after water flooding. (2) In the CO2 flooding, oil recovery increases gradually with increasing pressure for all three types of samples. Type II core samples have the highest recovery. Before miscibility, the oil recovered from type I and type II samples was primarily from large pores, however, the oil recovery mainly comes from medium pores when reaching miscibility. As for the type III samples, the oil produced in the immiscible state mainly comes from large and medium pores, and the enhanced oil recovery mainly comes from medium and small pores after reaching the near-miscible phase. (3) It can be seen from the microscopic re-sidual oil distribution that oil recovery will increase as the petrophysical properties of the rock model improve. The oil recovery of near-miscible flooding after water flooding regarding the type II model is up to 68.11%. The oil recovery of miscible flooding after water flooding about type III model is the highest at 74.57%. With increasing pressure, the proportion of flake residual oil grad-ually decreases, while the proportion of droplet-like and film-like residual oil gradually increases. Type II samples have a relatively large percentage of reticulated residual oil in the near-miscible stage.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

This paper presents GeoFlood, a new open-source software package for solving shallow water equations (SWE) on a quadtree hierarchy of mapped, logically Cartesian grids managed by the parallel, adaptive library ForestClaw (Calhoun and Burstedde, 2017). The GeoFlood model is validated using standard benchmark tests from Neelz and Pender (2013) and against George (2011) results obtained from the GeoClaw software (Clawpack Development Team, 2020) for the historical Malpasset dam failure problem. The benchmark test results are compared against GeoClaw and software package HEC-RAS (Hydraulic Engineering Center - River Analysis System, Army Corp of Engineers) results (Brunner, 2018). This comparison demonstrates the capability of GeoFlood to accurately and efficiently predict flood wave propagation on complex terrain. The results from comparisons with the Malpasset dam break show good agreement with the GeoClaw results and are consistent with the historical records of the event.

In this paper, a semi-empirical model of air waves induced by falling rock is described. The model is composed of a uniform motion phase (velocity close to 0 m·s^-1) and an acceleration movement phase. The uniform motion phase was determined based on experimentally and the acceleration movement phase was derived by theoretical analysis. A series of experiments were performed to verify the semi-empirical model and elucidated the law of the uniform motion phase. The acceleration movement phase accounted for a larger portion with a greater height of the falling rock. Experimental results of different falling heights of the goaf showed close agreement with theoretical analysis values. The semi-empirical model could accurately and conveniently estimate the velocity of air wave induced by falling rock. Thus, the semi-empirical model can provide a reference and basis for estimating the speed of air waves and designing protective measures in mines.

Acute and chronic respiratory diseases impose a significant economic and health burden. Distal small airway assessment requires invasive procedures such as a bronchoscopy and bronchoalveolar lavage. The Particles in Exhaled Air (PExA) device provides a non-invasive means of assessing small airways; it captures distal airway particles sized around 0.5-7m and contains particles of respiratory tract lining fluid (RTLF) that originate during airway closure and opening. The PExA device can measure particle count and mass according to particle size. Subsequent capture of particles in a thin membrane enables application of various analytical methods to assess a broad range of biomolecules including phospholipids, proteins, inflammatory profile, and other metabolites to characterise inflammation and diseases processes such as asthma, chronic obstructive pulmonary disease, acute respiratory distress syndrome, lung cancer, and more recently acute infections such as COVID-19. PExA analysis provides a promising alternative to traditional investigative methods in the assessment, diagnosis, and management of respiratory conditions. By evaluating specific biomarkers in the RTLF associated with airway inflammation, PExA may offer a more accurate and comprehensive understanding of the molecular-level changes in the small airways of patients with acute and chronic lung diseases.

Coastal inundation is recently requiring a significant attention worldwide. The increasing frequency and intensity of extreme events (sea storms, tsunami waves) are highly stressing the coastal envi-ronments, e.g. endangering a large number of residential areas, ecosystems, tourist facilities, and also leading to potential environmental risks. Predicting such events and the generated coastal flooding is thus of paramount importance and can be reached by exploiting the potential of different tools, like remote sensors and numerical modeling. To this aim, a combination is possible between marine radars and wave-resolving propagation models. While instruments like X-band radars are able at precisely reconstructing both wave field and bathymetry within a coastal area that is some kilometers offshore, wave-resolving Boussinesq-type models can reproduce the wave propagation in the nearshore and the consequent coastal flooding. The present work illustrates the reconstruc-tion of coastal data (wave field and seabed depth) conducted using radar signals and a specifically suited data processing, named “Local Method”, and the use of such coastal data to run numerical simulations of wave propagation (using the FUNWAVE-TVD solver) aimed at reproducing coastal inundation over different scenarios. Such scenarios are built using two different European beaches, i.e. Senigallia (Italy) and Oostende (Belgium), and three different directional spreading values, to evaluate the performances in case of either long- or short-crested waves. The overall validation of the methodology, in terms of maximum inundation, shows good performances, especially in case of short-crested wind waves. Furthermore, the application on the Oostende beach demonstrates that the present methodology might work only using open-access tools, i.e. an easy investigation of the coastal inundation and a potential low-cost integration into early warning systems.

It is concerning that Cameroon's urban centers are experiencing an alarming rise in air pollution as a result of urbanization, population growth, industrial activity, and transportation emissions. We examined the causes, health impacts, research methodology, case studies, and government measures to address the urgent issue of air pollution in Cameroon's urban regions. We have emphasized how Cameroon's air pollution levels have significantly increased as a result of causes like population expansion, urbanization, industrial emissions, and automobile exhaust A thorough discussion of the negative health impacts of extended exposure to air pollution is included, with special attention to the sensitivity of the old and young. These effects include respiratory disorders, cardiovascular ailments, and early mortality. We emphasized the pressing need for all-encompassing strategies to address air pollution, such as increased public awareness campaigns, stronger emissions regulations, the development of renewable energy sources, and better waste management. The techniques employed in studies on air pollution, like as epidemiological research and air quality monitoring, are also explained to provide light on the unique health dangers that Cameroonian urban dwellers must contend with. We emphasized in our conclusion the significance of joint efforts by legislators, medical professionals, and the general people to reduce air pollution and protect public health in Cameroon in order to create a cleaner and healthier future. In order to protect public health in the future, it is imperative that Cameroon's air pollution be addressed.

The article delves into the intricate phase transitions of 1-Octadecanol and n-Nonadecane within a binary system, unveiling dynamic structural changes under varying conditions. Through Fouri-er-transform infrared (FTIR) analysis, specific molecular vibrations were identified, shedding light on the molecular composition and interactions. The study highlights the challenges in detecting subtle phase transitions and emphasizes the individuality of molecular behaviours in closely related compounds. The findings underscore the complexity of phase transitions in binary systems and advocate for a nuanced approach to studying molecular structures and behaviours. Addi-tionally, the research contributes valuable insights into the molecular dynamics of Organic Polymer Functional Adsorption Materials, offering implications for synthetic waxy layers in plant epidermis.

Retiring coal power plants can reduce air pollution and health damages. However, the spatial distribution of those impacts remains unclear due to complex power system adjustments and pollution chemistry and transport. Focusing on coal retirements in Pennsylvania (PA), we analyze six counterfactual scenarios for 2019 that differ in retirement targets (e.g., reducing 50% of coal-based installed capacity vs. generation) and priorities (e.g., closing plants with higher cost, closer to Environmental Justice Areas, or with higher CO₂ emissions). Using a power system model of the PJM Interconnection, we find that coal retirements in PA shift power generation across PA and the Rest of PJM region leading to scenario-varying changes in the plant-level release of several air pollutants. Due to air pollution chemistry and transport and socio-demographics, these changes in turn give rise to a reduction of 10 to 182 PM_2.5-attributable deaths in PJM across the six scenarios, with most reductions occurring in PA. Scenarios that reduce more coal power generation yield greater aggregate health benefits due to air quality improvements in PA and adjacent downwind regions. In addition, vulnerable populations—in both PA and Rest of PJM—benefit most in scenarios that prioritize plant closures in PA near Environmental Justice Areas. These results demonstrate the importance of considering cross-regional linkages and socio-demographics in designing equitable retirement strategies.

In light of the critical and emerging global challenge posed by the increasing frequency and severity of heatwaves in recent decades, this study demonstrates a practical and robust workflow that bridges the gap in understanding how the effective integration of remote sensing data with ground-based observations can facilitate a comprehensive assessment of spatiotemporal heatwave patterns and trends in the central region of Thailand. This research transcends traditional methods, utilizing air temperature (Tair) and satellite-derived land surface temperature (LST) data from 1981 to 2019. Results exhibit that an analysis of Tair indicates increasing daytime heatwaves in peri-urban areas, with significant trends in heatwave number (HWN), heatwave frequency (HWF), and heatwave duration (HWD), heatwave amplitude (HWA) rises in urban settings while nighttime heatwaves significantly intensify in rural locales. Notably, LST trends reveal varied patterns, with peri-urban areas showing marked daytime increases in heatwave magnitude (HWM), HWA, and HWF. Correlation analysis (p=0.05) highlights strong daytime associations between Tair and LST in rural (HWN, HWF, HWD, r>0.90) and peri-urban (HWM, HWA, r>0.65) regions. Overall, this study advances approaches to the adaptable measurement and spatial-temporal pattern of heatwave-related risk areas, providing insights for decision-makers to develop sustainable practices and strategies for climate change adaptation.

IoTs and WSNs utilize their connectivity to enable solutions supporting a spectrum of industries in different and volatile environments. To effectively enhance the security and quality of service of networks, empirical research should take into account a variety of factors and be structured in a replicable manner. This will not only ensure scalability but also enable verification of conclusions, leading to more constructive outcomes. Cooja offers limited performance analysis capabilities of simulations, which are often extracted and calculated manually. In this paper, we introduce a framework and a toolkit that enable researchers to conduct structured and conclusive experiments considering different factors and metrics, experiment design to results analysis. Besides, this tool summarizes multiple network metrics and allows multiple scenarios. As proof of concept, this paper studies the flooding attacks on IoT and illustrates their impact on the network, leveraging the proposed framework and tools.

Significant amount of oil remains in the reservoir after primary and secondary operations and to recover the remaining oil, enhanced oil recovery (EOR) can be applied as one of the feasible options remaining nowadays. In this study new nano polymeric materials have been prepared from purple yam and cassava starches. The yield of purple yam nanoparticles (PYNPs) was 85% and that of cassava nanoparticles (CSNPs) is 90.53%. Synthesized materials were characterized through particle size distribution (PSA), zeta potential distribution, Fourier transform infrared spectroscopy (FTIR), differential scanning calorimetry (DSC) and transmission electron microscopy (TEM). The performance of PYNPs in recovering oil was better than CSNPs as found from recovery experiments. Zeta potential distribution results confirmed the stability of PYNPs over CSNPs (-36.3 mV for PYNPs and -10.7 mV for CSNPs). The optimum concentration for these nanoparticles has been found from interfacial tension measurements and rheological properties and it was 0.60 wt.% for PYNPs and 0.80 wt.% for CSNPs. More incremental recovery (33.46%) has achieved for the polymer that contained PYNPs in comparison to the other nano-polymer (31.3%). This opens the inception for a new technology for polymer flooding that may replace the conventional method that depends on partially hydrolyzed polyacrylamide (HPAM).

Background: Asthma is a widespread chronic respiratory disease that poses a significant public health challenge. The current study investigated the associations between air pollution and asthma severity among individuals residing near the Sohar industrial port (SIP) in Oman. Despite the presence of multiple major industrial complexes in Oman, limited knowledge regarding their impact on respiratory health is accredited. Hence, the primary objective of this study is to offer valuable insights into the respiratory health consequences of industrial air pollution in Al Batinah North. Methods: The state health clinics' records for patient visits related to asthma were collected for the timeframe spanning 2014 to 2022. Exposure was defined as the distance from SIP, Majan Industerial Area (MIA) and Sohar Industerial Zone (SIZ) to determine high, intermediate, and low exposure zones (12 km, respectively). Exposure effect modifications by age, gender, and smoking status were also examined. Results: The conducted cross-sectional study of 410 patients (46.1% males and 53.9% females) living in over 17 areas around SIP revealed that 73.2% of asthmatics were under 50 years old, with severity significantly associated with closeness to the port. Risk ratios were estimated to be (RR:2.42; CI95%: 1.01–5.78), (RR:1.91; CI95%: 1.01–3.6), and (RR:1.68; CI95%: 0.92–3.09) for SIP, MIP and SIZ areas, respectively, compared to the control area. Falaj Al Qabail (6.4 km) and Majees (6 km) had the highest number of asthma patients (N. 69 and N. 72), and highest percentages of severe asthma cases among these patients (28% and 24%) with significant risk ratios (RR:2.97; CI95%: 1.19–7.45 and RR:2.55; CI95%: 1.00–6.48), correspondingly. Moreover, severe asthma prevalence peaked in the 25-50 age group (RR:2.05; CI95%: 1.26–3.33), and this linkage between asthma and age was much more pronounced in males than females. Smoking and exposure to certain contaminant (dust and smoke) increased also the risk of severe asthma symptoms, but their effects were less important in the high risk zone, suggesting much more important risk factor. A neural network model accurately predicted asthma risk (94.8% accuracy), with proximity to Sohar Industrial Port as the most influential predictor. Conclusion: The study highlights the High asthma burden near Sohar Industrial Port, linked to port proximity and smoking and wind direction as major risk factors. These findings inform vital public health policies to reduce air pollution and improve respiratory health in the region, prompting national policy review.

The Predicted Mean Vote (PMV) and the Predicted Percentage of Dissatisfied (PPD) indices are used to assess the indoor environment in terms of human thermal comfort-discomfort. In this study, an experimental combined objective and subjective investigation of thermal comfort perception has been performed in students between 16-18 years old, in a non-air-conditioned school building. The objective approach included instrumentation measurements and data processing according to ISO 7730, whereas, the subjective one was based on answers collection following ISO 10551. The study is mainly devoted to the verification of Fanger’s approach in a building, in free running conditions, under a mild (moderate) climate.The comparison between instrumentation data and questionnaire results presented an underestimation of the mean vote, predicting a cooler sensation than the actual one.

CO2 flooding stands as a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in its oil recovery, yet a comprehensive quantitative analysis remains an area in need of refinement. In this study, we have developed 1D and 2D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly-miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns are determined. A novel approach of the contour area calculation method is introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding geological parameters, oil viscosity, and injection-production parameters. Furthermore, the Random Forest (RF) algorithm is employed to identify the controlling factor of the sweep coefficient, as determined by out-of-bag (OOB) data displacement analysis. The results show that the miscible front is located at the point of maximum CO2 content in the oil phase. The immiscible front occurs at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moves at a faster rate compared to the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impact the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibits the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio is a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection-production parameters also play a pivotal role in sweep coefficient. Decreased well spacing and increased gas injection rates are found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates can improve the miscibility degree of partly-miscible flooding from 0.69 to 1.0. Oil viscosity proves to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly-miscible flooding patterns. Conversely, gravity segregation primarily governs the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerges as a paramount influence, with a factor importance value (FI) reaching 1.04. these results provide a theoretical foundation for the application of CO2 flooding, enhancing the understanding of the critical factors governing its success.

River renaturation can be an effective management method for restoring the floodplain's natural capacity and minimizing the effects during high flow periods. A 1D-2D HEC-RAS model, in which the flood plain was considered as 2D and the main channel as 1D, was used to simulate flooding in the restored reach of the Spree River. When computing in this model, finite volume and finite difference approximations using the Preissmann approach are used for the 1D and 2D models, respectively. To comprehend the sensitivity of the parameters and model, several scenarios were simulated using different time steps and grid sizes. Additionally, dykes, dredging, and changes to the vegetation pattern have been used to simulate flood mitigation measures. The model predicted that flooding would occur mostly in the downstream portion of the channel in the majority of the scenarios without mitigation measures, whereas with mitigation measures, flooding in the floodplain would be greatly reduced. By preserving the natural balance on the channel's floodplain, the restored area needs to be kept in good condition. Therefore, mitigating measures that balance the area's economic and environmental aspects must be considered in light of the potential for floods.

In today's context of rising sea levels and subsiding land topography, coastal flooding is a major concern for coastal areas, both nationally, regionally, and internationally. A detailed understanding of these two phenomena is a prerequisite for effective coastal flood management. The main objective of the present study is to contribute to the understanding of the impact of subsidence and sea-level rise on coastal flooding in Saint-Louis, and in particular the Langue de Barbarie, by producing a vulnerability map of submerged surfaces. To this end, the Synthetic Aperture Radar (SAR) interferometry technique is used to process a time series of Sentinel-1 images and estimate land subsidence in the Saint-Louis and Langue de Barbarie area. Interferometric SAR (InSAR) measurements are merged with RCP 2.6 sea-level rise scenarios to identify predicted flooded areas and provide a flood vulnerability map. At the Langue de Barbarie, topographic subsidence is estimated at between -6.4 and -0.4mm/year. In this study, we show that local land subsidence may increase vulnerability to flooding caused by sea-level rise based on 2100 projections. This may represent an increase in the flood zone in the study area. Based on the RCP 2.6 scenario and the subsidence rates obtained, a significant part of the St. Louis coastline and city would be subject to coastal and fluvial flooding for the years 2040 and 2100. For these dates, 29 to and 36 Km2 of the studied area would be occupied by water. Given this situation, research in Saint-Louis needs to focus on adaptation scenarios to coastal risks, to protect coastal communities and safeguard the city's historical heritage.

The risk related to embankment dam breaches needs to be evaluated in order to prepare emergency action plans. The physical and hydrodynamic parameters of the flood wave generated from dam-failure event correspond to various breach parameters such as width, slope and formation time. This study aimed to simulate dam-breach failure scenario of Yabous dam (NE Algeria) and analyze its influence on areas (urban and natural environments) downstream the dam. The simulation was completed using the sensitivity analysis method in order to assess the impact of breach parameters on the dam-break scenario. The propagation of flood wave associated to dam-break was simulated using the one-dimensional HEC-RAS hydraulic model. This study ap-plied a sensitivity analysis of three breach parameters (slope, width, and formation time) in five sites selected downstream the embankment dam. The simulation showed that the maximum flow of the flood wave recorded at the level of the breach was 8768 m3/s, which gradually attenuated along the river course to reach 1579.2m3/s at about 8.5km downstream the dam. This study estab-lished the map of flood-prone areas that illustrated zones threatened with the flooding wave trig-gered by the dam failure due to extreme rainfall events. The sensitivity analysis showed that flood wave flow, height and width revealed positive and similar changes for the increase in adjustments (±25% and ±50%) of breach width and slope in the 5 sites. However, flood wave parameters of breach formation time showed significant trends that changed in the opposite direction compared to breach slope and width.

The article presents the results of a morpho-physiological assessment of rice samples by the strength of growth, as well as an assessment of the degree of development of the conducting system of the flag leaves of rice plants. The resistance of varieties to flooding is very relevant in the fight against weeds due to the deep layer of water that weeds cannot overcome. Currently, there are no zoned varieties in Russia that would meet these requirements. Therefore, the problem of creating such rice varieties is urgent, as it will reduce production costs, reduce grain losses during harvesting, improve the quality of the products obtained, and also reduce the pesticide load on the ecosystem. As a result of research, a number of studied samples revealed the potential to quickly lengthen the first leaves, overcome a large layer of water and accumulate vegetative mass. As a result of the evaluation of the conducting system of the flag leaf of rice plants, it was found that in plants with the flood resistance gene Sub1A, which stops growth under water, the conductive beams were smaller in comparison with other fast-growing samples with the AG, Sk genes. Consequently, fast-growing samples have bigger sizes of the conducting system as a resistance mechanism.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Sinkhole flooding is an essential hydrological process to recharge karst aquifer in arid to dry sub-humid regions. On the other hand, the increase of rain extremes is one of the major consequences of the global warming, together with the expansion of drylands. Thus, appropriate runoff regulation in endorheic karst basins in order to reduce the risk of flooding and improve the quantity and quality of the water drained by sinkholes will be more and more crucial. With these premises, a systematic review was performed by using WoS engine to infer the best practices for the karst water management in regions actually or potentially affected by water scarcity. Hydrological models are essential to manage the consequences of climate change on karst water resource, however the review shows that providing the tools necessary for reliable modeling is still challenging. Finally, due to the intrinsic vulnerability of the karst aquifers, pollution reduction and wastewater recycling policy will play key role in the next decades.

The effects of global warming combined with the progressive expansion of urbanization have considerably increased exposure to urban flooding and runoff widespread erosion risk, also causing shallow landslides and mud flows, respectively in urbanized areas of lowland and hill/foothill environments. Increasing urban flooding resilience has become a priority at virtually all levels of governance. The analysis of a different hazard scenarios, in which various hydro-meteorological conditions and management alternatives are examined, should act as the basis for the effective design and evaluation of interventions to improve urban flooding resilience. Turin Metropolitan Area (TMA), located in north-western Italy, represents a unique case due to its complex orography, with a mountainous sector in the west side and a flat or hilly part in the east side. During the warm season, these environmental conditions make the urban area prone to severe atmospheric convection causing frequent hailstorms and rainstorms of high intensity that may impact on urban infrastructures (i.e., drainage system and road network), thus requiring an adequate management as a key factor to reducing risk and losses. The urban areas of TMA are monitored by polarimetric Doppler weather radars and by a dense rain gauges network. Analyzing several case studies of urban flooding, this research work assesses the feasibility of a meteorological radar early warning system based on the identification of rainfall thresholds that characterize urban flooding, occurring in the lowlands, and the runoff erosion phenomena affecting the urbanized hills and foothills.

Downpours are increasing in frequency and severity due to climate change. Cities are particularly susceptible to downpours because of their large share of impervious surfaces. Minimising pluvial flood risk requires all involved stakeholders to collaborate and overcome probable barriers. Simultaneously, an increase in citizen engagement in climate adaptation is preferred, whereas experiences with inclusive decision-making are still limited. The aim of this paper is to obtain a deeper understanding of how the capacity to govern pluvial flood risk can be developed through citizen engagement. We scrutinised the capacity of local actors to govern pluvial flood risk in the city of Utrecht, the Netherlands. For the analysis of Utrecht’s problem-solving capacity, the Governance Capacity Framework provided a consistent assessment of governance components. The results indicate that Utrecht’s capacity to govern pluvial flooding is relatively well-developed. Collaboration between public authorities is advanced, sufficient financial resources are available and smart monitoring enables high levels of evaluation and learning. However, citizen awareness and engagement in policy making is rather low. Accordingly, citizens’ willingness to pay for flood adaptation is limited. Stimulating flood risk awareness by combining financial incentives with more advanced arrangements for active citizen engagement is key for Utrecht and other cities.

The use of unmanned aerial aircrafts (UAVs) is governed by strict regulatory frameworks that prioritize safety. To guarantee safety, it is necessary to acquire and maintain situational awareness (SA) throughout the operation. Existing Canadian regulations require pilots to operate their aircrafts in visual line-of-sight. Therefore, the task of acquiring and maintaining SA primary falls to the pilots. However, the development of aerial transport is entering a new era with the adoption of a highly dynamic and complex system known as advanced air mobility (AAM), which involves UAV operating autonomously beyond visual line-of-sight. SA must therefore be acquired and maintained primarily by each UAV through specific technologies and procedures. In this paper, we review these technologies and procedures in order to decompose the SA of the UAV in the AAM. We then use the system modeling language to provide a high-level structural and behavioral representation of the AAM as a system having UAV as its main entity. In a case study, we analyze one of the flagships UAVs of our industrial partner. Results show that this UAV doesn’t have all the technologies and methodologies necessary to achieve all the identified SA goals identified for the safety of the AAM. This work is a theoretical framework intended to contribute to the realization of the AAM, and we also expect to impact the future design and utilization of UAVs.

The Upper Hunter Valley is a major coal mining area in New South Wales (NSW), Australia. Due to the ongoing increase of mining activities, PM10 (air-borne particle with an aerodynamic diameter less than 10 micrometres) pollution has become a major air quality concern in local communities. The early part of this study identified two air quality subregions in the valley. This paper aims to provide a holistic summarisation of the relationships between elevated PM10 pollution in two subregions and the local- and synoptic-scale meteorological conditions for spring and summer, when PM10 pollution is relatively high. A catalogue of twelve synoptic types and a set of six local meteorological patterns have been quantitatively derived and linked to each other using the self-organising map (SOM) technique. The complex meteorology-air pollution relationships have been visualised/interpretated on the SOM planes for two representative locations. It was found that the influence of local meteorological patterns differed significantly for mean PM10 levels vs the occurrence of elevated pollution events and between air quality subregions. In contrast, synoptic types showed generally similar relationships with mean vs elevated PM10 pollution in the valley. Two local meteorological patterns, the hot-dry-northwesterly wind conditions and the hot-dry-calm conditions, were found most PM10 pollution conducive in the valley when combined with a set of synoptic counterparts. These synoptic types are featured with the influence of eastward migrating continental high pressure system and westerly troughs, or a ridge extending northwest towards coastal northern NSW or southern Queensland from the Tasman Sea. The method and results can be used in air quality research for other locations of NSW, or similar regions elsewhere.

This study investigates the mean annual water temperature trends at the confluence of the Sava and Danube Rivers, along with air temperature trends at the Belgrade meteorological station, spanning from 1956 to 2020. Results reveal a consistent increase in temperature across all three measuring stations, with the Danube experiencing a rise of 0.34°C/10 years, the Sava at 0.44°C/10 years, and Belgrade's air temperature increasing by 0.39°C/10 years. Employing the RAPS method, sharp rises in water temperature were pinpointed in 1989 for the Sava and 1990 for the Danube, while Belgrade's air temperature surge began in 1998. The highest intensity of air temperature increase within the recent period (1998-2020) was observed at the Belgrade observatory, reaching 0.76°C/10 years. Notably, the Sava exhibited a faster increase in water temperature over the last thirty years compared to the Danube. August marked the peak average water temperature for both rivers, while July recorded the highest average air temperature in Belgrade. Despite differing flow rates, both rivers exhibit similar hydrological regimes, with maximum flows occurring in April and minimum flows in August for the Sava, and October for the Danube. Seasonal temperature increases were most pronounced in summer, notably in August, with the smallest rises occurring during cold periods. Additionally, an inverse proportional relationship between mean annual water temperatures and discharges was observed at both river stations.

Chemical flooding methods are used to recover the remaining oil after water flooding, and surfactant-polymer (SP) flooding is an important chemical flooding technology. It is of great significance to design and screen high-performance oil displacement agents in order to overcome the increasingly challenging high temperature (>70 ℃) and high salinity (>10,000 mg/L) reservoirs. Based on the characteristics of high temperature (70 ℃) and high salinity (151,000 mg/L) in the Qinghai Gasi reservoir, the performance of the SP flooding system was studied. This study considered interfacial tension, emulsification, viscosity, compatibility, and oil displacement efficiency. The selected formula demonstrated high resistance to both salinity (151,000 mg/L) and temperature (70 ℃), characterized by a low oil-water interfacial tension (10-2 mN/m) and high viscosity (18.13 mPa.s). After water flooding achieved an oil recovery rate of 64.64%, the subsequent replacement rate of crude oil increased by 26.95%, confirming that SP flooding can be used as a technology for enhancing oil recovery in high-temperature, high-salinity reservoirs represented by Qinghai Gasi reservoirs.

The storm 'Daniel' has caused the most severe flood phenomenon that Greece has ever experienced, with thousands of hectares of farmland submerged for days. This led to sediment deposition in the inundated areas, which significantly altered the chemical properties of the soil, as revealed by extensive soil sampling and laboratory analysis. Causal relationships between soil chemical properties and sediment deposition were extracted using the DirectLiNGAM algorithm. Results of causality analysis showed that the sediment deposition affected the CaCO3 concentration in the soil. Also, causal relationships were identified between CaCO3 and available phosphorus (P-Olsen), as well as between sediment deposit depth and available manganese. The quantified relationships between the soil variables were then used to generate data using a Multiple Linear Perceptron (MLP) regressor for various levels of deposit depth (0, 5, 10, 15, 20, 25 and 30 cm). Then linear regression equations were fitted across the different levels of deposit depth to determine the effect of deposit depth on CaCO3, P, and Mn. The results show that there is a linear slope of 0.12, -0.16, and 0.13, for CaCO3, P, and Mn with deposit depth, respectively. Statistical analysis indicates that corn growing in soils with sediment over 10 cm requires a 31.8% increase in P rate to prevent yield decline. Additional notifications regarding cropping strategies in the near future are also discussed.

In order to explore the effect of fertilization patterns on the growth of rapeseed seedlings under waterlogging stress, three fertilization patterns (conventional fertilization, supplemental organic fertilization, and supplemental microbial fertilization) were set up using the variety Xiangyou 708 as the material, and waterlogging treatment was carried out during the seedling stage of rapeseed. The effects of fertilization patterns on the growth of rapeseed seedlings and rhizosphere microorganisms under waterlogging stress were investigated. The results showed that all three fertilization patterns exhibited that waterlogging stress inhibited the growth of rapeseed seedlings, inhibited root activity, and changed the structure of rhizosphere bacterial colonies. However, supplemental organic fertilization and microbial fertilization could better promote the growth of rapeseed seedlings, reduce the impact of waterlogging stress on the growth of rapeseed seedlings, and accelerate the recovery of rapeseed seedlings after waterlogging stress. In addition, supplemental microbial fertilization could also change the structure of rhizosphere bacterial colonies. Under normal water supply, supplemental organic fertilization enriched P_Bacteroidota, P_Actinobacteriota, P_Chloroflexi, and G_Flavisolibacter in the rhizosphere soil of rapeseed, while supplemental microbial fertilization enriched P_Bacteroidota and G_Flavisolibacter in the rhizosphere soil of rapeseed. After 7 days of waterlogging treatment, supplemental organic fertilization enriched P_Verrucomicrobiota in the rhizosphere soil of rapeseed, while supplemental microbial fertilization enriched P_Actinobacteriota, G_SC-I-84, and G_Ellin6067 in the rhizosphere soil of rapeseed. The enrichment of these bacteria may be related to the growth promotion and waterlogging tolerance of rapeseed. This study provides evidence that microbial fertilizer and organic fertilizer can promote the growth of rapeseed and enhance its waterlogging tolerance, as well as evidence that some rhizosphere microorganisms have a potential role in promoting the growth and waterlogging tolerance of rapeseed.

This study assesses coastal flooding extension mapping based on two innovative approaches. The first is based on the coupling of two robust numerical models (SWASH and LISFLOOD), in this case, discharges were extracted from the wave overtopping results from SWASH 1D and set as boundary conditions for LISFLOOD on the crest of an existing seawall where overtopping typically occurs. The second, hereby called the ‘Tilted Bathtub Approach’ (TBTA), is based on wave run-up levels and buffering the affected area of a prior flooding event, adjusting it for expected sea-states according to different return periods. The proposed approaches are applied to a case study on the Northern Portuguese coast, at Furadouro beach, in the municipality of Ovar, which has been facing multiple flooding episodes throughout recent years, including a dramatic storm in February 2014. This event was used as validation for the proposed methods. A 30 years long hourly local wave climate time series was used both to perform an extreme value analysis in order to obtain expected sea-states according to different return periods, and also for performing a sensitivity test for established empirical formulas to estimate wave run-up at this particular case. Results indicate both approaches are valuable: they yield coherent flood extension predictions that align well with the real inundated area from the 2014 storm. The convergence of these findings underscores the potential for these methods in future coastal flood risk assessment and planning.

The interaction between oceanographic, meteorological, and hydrological factors can result in an extreme flooding scenario in the low-lying coastal area, called compound flooding (CF) events. For instance, rainfall and storm surge (or high river discharge) can be driven by the same meteorological, tropical or extra-tropical cyclones, resulting in a CF phenomenon. The trivariate distributional framework can significantly explain compound events' statistical behaviour reducing the associated high-impact flood risk. Resolving heterogenous dependency of the multidimensional CF events by incorporating traditional 3-D symmetric or fully nested Archimedean copula is quite complex. The main challenge is to preserve all lower-level dependencies. An approach based on decomposing the full multivariate density into simple local building blocks via conditional independence called vine or pair-copulas is a much more comprehensive way of approximating the trivariate flood dependence structure. In this study, a parametric vine copula of a drawable (D-vine) structure is introduced in the trivariate modelling of flooding events with 46 years of observations of the west Coast of Canada. This trivariate framework searches dependency by combining the joint impact of annual maximum 24-hr rainfall and the highest storm surge and river discharge observed within the time ±1 day of the highest rainfall event. The D-vine structures are constructed in three alternative ways by permutation of the conditioning variables. The most appropriate D-vine structure is selected using the fitness test statistics and estimating trivariate joint and conditional joint return periods. The investigation confirms that the D-vine copula can effectively define the compound phenomenon's dependency. The failure probability (FP) method is also adopted in assessing the trivariate hydrologic risk. It is observed that hydrologic events defined in the trivariate case produce higher FP than in the bivariate (or univariate) case. It is also concluded that hydrologic risk increases (i) with an increase in the service design life of the hydraulic facilities and (ii) with a decrease in return periods.

AbstractLocal estimates of coastal flood risk are required for coastal planning and development, including the location and design of sea-defences and coastal buildings, such as harbours and associated infrastructure. This paper discusses the use of three parameters associated with estimating such risks; the flood return period, the instantaneous flood probability and the flood design risk, and it describes the mathematical background for their derivation. The discussion is extended to include the effects of sea level rise and how it can be incorporated into the calculations. Flood height can vary quite rapidly with distance along the coast, being affected by coastal topology, which may magnify or diminish the tidal and surge effects. Similarly land heave influences the local effects of sea level rise and can be influenced by water extraction, tectonic movements and melting ice. Tide gauge measurements provide a local historical record from which the various parameters can be retrieved. This paper discusses the algorithms used to derive these measures from tide-gauge records. The figures have been derived for four tide gauges located on the UK east coast.

This study integrated coastal-watershed models and combined a risk assessment method to develop a methodology to investigate the impact resulting from coastal disasters under climate change. The mid-western coast of Taiwan suffering from land subsidence was selected as the demonstrative area for the vulnerability analysis based on prediction of sea level rise (SLR), wave run-up, overtopping, and coastal flooding under the scenarios of 2020 to 2039. Database from tidal gauges and satellite images were used to analyze sea level rise using EEMD (Ensemble Empirical Mode Decomposition). Extreme wave condition and storm surge were estimated by numerical simulation using WWM (Wind Wave Model) and POM (Princeton Ocean Model). Coastal inundation was then simulated via WASH123D watershed model. The risk map of study areas based on the analyses of vulnerability and disaster were established using the AHP (Analytic Hierarchy Process) technique. Predictions of sea level rise, the maximum wave condition and storm surge under the scenarios of 2020 to 2039 are presented. The results indicate that the sea level at the mid-western coast of Taiwan will rise in an average of 5.8 cm, equivalent to a rising velocity of 2.8 mm/year. The analysis indicates that Wuqi, Lukang, Mailiao, and Taixi townships are susceptive, low resistant and low resilient, and reaches the high risk level. The assessment provides that important information for making adaption policy in the mid-western coast of Taiwan.

Chemical flooding is one of the effective methods to recover large volumes of oil from sandstone formations after primary depletion. However, silica dissolution often occurs during Alkaline-Surfactant-Polymer (ASP) flooding, affecting the petro-physical properties of the formation. To address this issue, samples from Berea sandstone formations were treated with various brine solutions, through static tube tests and core flooding experiments. Analytical tests such as DR/2800 spectrophotometer and scanning electron microscope were used to evaluate the silica solubility and the alteration in mineral content. The results indicated that the silicate contents decreased after the saturation due to silica solubility in the solution. Increasing brine salinity to 40,000ppm and introducing Magnesium and Calcium ions to the solution, reduces the silicate contents by 5.03 % and 7.32 %. Moreover, saturating the samples with ASP solution, further reduced the silicate contents by 14.86 %. This reduction is associated with a relative increase in silica solubility and pH of the solution. Silica dissolution affects the pore microstructure, which resulted in increasing the porosity and pore volume after the core flooding. The injection of the ASP solution increased the porosity by 5.83%, thus the pore volume increased from 17.72 to 18.76cc. This is associated with the high silica solubility and the increase of solution pH in the ASP solution. The permeability of the samples generally reduced after the core flooding, due to the silica solubility. However, injecting the ASP solution, resulted in a major reduction of the permeability by more than 75%. These changes in the petro-physical properties can lead to severe formation damage, and affect hydrocarbon production. This study assists in understanding the impact of silica dissolution during ASP treatment and addresses the factors involved. Efficient utilization of chemical flooding can help mitigating silicate scaling within the formation, and extend field productivity.

Water pollution associated with flooding is one of the major problems in cities in the global South. However, studies of water quality dynamics during flood events are not often reported in literature, probably due to difficult conditions for sampling during flood events. Water quality parameters in open water (canals, rivers, and lakes), floodwater on roads and water in sewers have been monitored during the extreme fluvial flood event on 7 October 2013 in Can Tho city, Vietnam. This is the pioneering study of urban flood water pollution in real time in Vietnam. The results showed that water quality is very dynamic during flooding, especially at the beginning of the event. In addition, it was observed that the pathogen and contaminant levels in the floodwater are almost as high as in sewers. The findings show that population exposed to flood water runs a health risk that is nearly equal to that of being in contact with sewer water. Therefore the people of Can Tho not only face physical risk due to flooding, but also exposed to health risk.

Traffic congestion is one of the foremost problems confronted by the urban and suburban tenants of today. Traffic congestion increases vehicle emissions and degrades air quality. Urban planners and policy makers have consequently been always investigating choices to alleviate traffic congestion and to enhance air quality. Teleworking is one option that has received significant consideration and has been studied in the recent past. The aim of the study is to explore the relationship between teleworking, air quality and traffic in Switzerland. The analysis relies on panel individual and household level data over the period 2002-2013. We examine five main air pollutants; the sulphur dioxide (SO₂), the ground-level ozone (O₃) the nitrogen dioxide (NO₂), the carbon monoxide (CO) and the particulate matter less than 10 microns (PM₁₀). Based on the fixed effects estimates, teleworking reduces traffic volume by 1.9 per cent. Furthermore, the reduction observed on air pollution is higher for NO₂, CO and PM₁₀ ranging between 3.3-3.7 per cent, followed by O₃ at 2.3 per cent and SO₂ at 2.1 per cent. According to instrumental variable (IV) approach and the two stage least squares (2SLS) method, the effect is higher ranging between 2.6-4.1 per cent. The respective reduction on traffic becomes 2.7 per cent. Overall, the main concluding remark of the study is that teleworking can be a promising tool for urban planning and development, focusing at the traffic volume reduction, and the air quality improvement. Additional policy implications of teleworking and its beneficial effects for the society are further discussed.

No doubt pollution is a global problem which must be holistically tackled. In doing this, adequate knowledge of the sources of pollution is important, therefore the aim of this paper is to review source apportionment with reference to top-down and bottom-up methods. In this paper, dispersion modeling, emissions inventory, and sampling methods were discussed. Also, analytical methods involved in top-down source apportionment were mentioned. The two techniques are needed to evaluate pollutants and their sources. Based on these two approaches, pollution control strategy would be developed and decisions can be made in deciding the right approach to solve or reduce the pollution problems.

The sudden onset of natural hazards such as a flash flood events can be devastating to a country or region, often affecting numerous communities, and humanitarian supply chains play a major role in enabling the timely recovery of economic and social activities. However, the uncertainty and suddenness of natural disasters such as flash floods, as well as the potential for aftershocks, require humanitarian supply chains to be resilient during the relief process. This research first adopts the Delphi and literature review methods to identify the key indicators in the humanitarian supply chain to form an evaluation index system. Then, taking the 2021 mega-flash flood event which affected four cities in the mountainous region under the jurisdiction of the Zhengzhou municipal government, the ANP method is used to calculate the weights of each indicator and combines the weighted results with the Multi-styling and stereotyping method under Pythagorean fuzzy (PFs-VIKOR) to make an evaluation of the resilience of the humanitarian supply chain in the relief process. The findings suggest that policy makers and decision makers should pay close attention to the coordination of the parties involved in the humanitarian supply chain and improve the level of resilience of the entire supply chain by enhancing the resource scheduling capacity and responsiveness. At the same time, the VIKOR evaluation of the 4 cities highlighted the humanitarian supply chain in Dengfeng City to be most effective in this event due to the close cooperation and positive response of all parties involved in the humanitarian supply chain. The findings of this research provide some useful suggestions and guidance to the various practitioners involved in the humanitarian supply chain. Furthermore, the evaluation of the performance of the four cities in this mega-flash flood event provides some helpful indication of the importance of the various emergency measures which can help to inform policy recommendations for the Zhengzhou municipal government.

The naphtha cracking process results in the production of ethylene, propylene, mixed C4, and pygas, which are all olefins. Distillation columns and cracking furnaces are the primary units of operation. The price of raw materials accounts for 80% of production costs. There is also the pos-sibility of using LPG, a less expensive raw material, in place of some of the naphtha. A change in the raw material will affect the operability of the distillation columns and influence the yield on the cracking side. To determine the best naphtha substitution for LPG without creating a hydraulic problem (Jet Flooding) in distillation columns, analysis utilizing simulation tools must be done. To simulate the substitution of naphtha for other feedstocks, a reliability model is being built by comparing simulation results with data from the actual plant. LPG flow is a free variable that is being used to substitute naphtha. The effects of economically advantageous naphtha substitution for LPG can be assessed with the use of simulation tools without impairing plant operability. Optimum naphtha substitution rate is 21.14% from base case which resulting jet flooding occurred at Propylene Fractionator No 2. By implementing this substitution case, benefit that can be driven $22,772.02/ hour.

Climate change and development have increased urban flooding, requiring modernization of stormwater infrastructure. Retrofitting standard passive systems with controllable valves/pumps is promising, but requires real-time control (RTC). One method of automating RTC is reinforcement learning (RL), a general technique for sequential optimization and control in uncertain environments. The notion is that an RL algorithm can use inputs of real-time flood data and rainfall forecasts to learn a policy for controlling the stormwater infrastructure to minimize measures of flooding. In real-world conditions, rainfall forecasts and other state information, are subject to noise and uncertainty. To account for these characteristics of the problem data, we implemented Deep Deterministic Policy Gradient (DDPG), an RL algorithm that is distinguished by its capability to handle noise in the input data. DDPG implementations were trained and tested against a passive flood control policy. Three primary cases were studied: (i) perfect data, (ii) imperfect rainfall forecasts, and (iii) imperfect water level and forecast data. Rainfall episodes (100) that caused flooding in the passive system were selected from 10 years of observations in Norfolk, Virginia, USA; 85 randomly selected episodes were used for training and the remaining 15 unseen episodes served as test cases. Compared to the passive system, all RL implementations reduced flooding volume by 70.5% on average, and performed within a range of 5%. This suggests that DDPG is robust to noisy input data, which is essential knowledge to advance the real-world applicability of RL for stormwater RTC.

Air pollution is a man-made environmental-related problem and has importance globally among all environmental issues. It is described as an atmospheric situation in which several components appear at high attention above their ambient level and generate a quantifiable effect on vegetation, animals, and people. Air pollution and its control are a universal problem and have become an issue of great trouble for us in current years. However, monitoring and measurement of the concentration of air pollutants are most difficult in assessment to monitoring other components in the environment. Air pollutants are transported to polar regions by different mechanisms such as long-range atmospheric transport or grasshopper effects and via anthropogenic activities. After reaching the polar regions, they settle down and remain as such for a long-time due to their persistent nature. They can distress the environment and wildlife of the polar regions. Generally, dangerous chemicals may cause a risk of well-being effects, whereas lethal pollutants focus on one physiological reaction. We reviewed the available information on air pollution (occurrence, sources, and harmful effects) in the polar regions.

Shenzhen is China’s top ten clean air city and the cleanest air megacity. Even so, epidemiologic studies have shown ambient air pollution had significant adverse impacts on human health in this less polluted city. In this study, the concentrations of six criteria air pollutants (PM2.5, PM10, O3, NO2, SO2, and CO) from 2014 to 2017 were analyzed and compared to thresholds of both national and international air quality standards. The results showed concentrations of all air pollutants were below target values of current national air quality standard, but levels of particulate matter (PM) and O3 were still much higher than the recommended levels by the World Health Organization. Within national air quality standards, the number of over-limit days was rare with few variations between highly polluted and low pollution areas. The air quality improvement was slowing down recently. Our results suggest annual and daily thresholds for PM are too loose for air quality improvement in Shenzhen. Hence, we call for evaluation and establishment of tougher air quality standard.

The evaluation of the possibility of obtaining dihaploids by the method of anther culture in vitro to accelerate selection for resistance to prolonged flooding of seeded rice with water was carried out. The object of research is rice hybrids F2 of the Rice Breeding and Seed Production Laboratory of the “Donskoy” ASC, obtained as a result of interbreeding the best economically valuable varieties with samples bearing genes of resistance to prolonged flooding with water. Basic nutrient medium with an optimal composition of nutrition elements and growth hormones stimulating callo- and morphogenesis were used. For the induction of callus formation, 12604 anthers were planted, according to 26 hybrid combinations represented by 68 plants, as a result, 716 neoplasms were obtained, including 586 non–morphogenic callus, 130 regenerating plants. Cultivation of anthers revealed large genotypic differences in the samples. According to the responsiveness to neoplasms, 60% of the panicles showed a positive result, the rest did not give callus. The most responsive to the formation of callus were hybrid combinations: 5009/2 – 84 pcs., 5010/2 – 94 pcs., 4565/3 – 85 pcs., 4641/2 – 69 pcs. They also showed the ability to morphogenesis. Androgenic plants were obtained by 14 hybrid combinations, their share was 1.03% of the total number of inoculated anthers. 30 green regenerative lines from four rice hybrids were obtained, differing in visual morphological assessment: 5009/2 - 5 pcs., 5010/2 – 5 pcs., 4565/3 – 2 pcs., 4641/2 – 18 pcs. The isolated lines are characterized by good responsiveness in the culture of anthers in vitro, carry genes for resistance to prolonged flooding, and can be used in rice breeding programs using DG technologies.

Groundwater (GW) flooding mechanisms differ from river flooding both spatially and temporally, and preventative methods against groundwater flooding must take this into account. Although groundwater flooding caused by river water rise occurs seldom, it can occasionally become severe and last for a long time if the river is significantly flooded. In the southwest portion of the research domain, Friedrichshafen with a few urban communities, the level of the groundwater table was discovered to be roughly 1 m below the surface. It was discovered that the urban settlement area only has one-story buildings. In the study region, it is typical for the single-story building's foundation bottom level to extend up to a depth of about 1.5 meters. Therefore, flood mitigation methods are taken into account for the southwest portion of the study region. The installation of a pumping well, drainage, and a barrier in the affected area are three different flood control strategies that are taken into consideration for the study area. From a technical and cost-benefit perspective, installing a pumping well that withdraws water and lowers the groundwater table was found to be the most effective flood control measure locally in a small region (e.g., 1km x 1km). By contrast, removing groundwater by building drainage and barriers was also shown to be ineffective to lower the groundwater table over an extended region and was significantly more expensive than the installation of wells. Additionally, when river flooding is taken into account compared to the default scenario where no intake of water from the river is included along the western border of the study area, it is discovered that the spread of pollution is significantly greater.

Slimy sculpin (Uranidea cognata) inhabitat coldwater streams in southeastern Minnesota, USA, many of which were subjected to probable 2000-year flood events in August 2007. Floods scoured streambeds, created new stream channels, and greatly reduced benthic invertebrate communities that serve as the primary food resource for sculpin. Diets and Fulton condition of sculpin in Gilmore Creek (with moderate flooding) and Garvin Brook (with very severe flooding) had been examined just prior to flooding, and were re-examined two weeks after flooding to assess possible diet and condition changes. Diets, condition, and reproductive fitness of sculpin were examined seven months post-flood in these same two streams, plus nearby Trout run (also experienced very severe flooding). Sculpin condition declined significantly post-flood in Garvin Brook, but improved in Gilmore Creek. Prior to spring spawning, condition of Garvin Brook sculpin had improved, but Gilmore Creek fish condition worsened. Sculpin diets were more diverse before and after flooding in Gilmore Creek than in Garvin Brook, although diets of fish from both streams were dominated (>55%) by midge (Diptera: Chironomidae) larvae. Diets differed significantly before versus after flooding in the more severely flooded Garvin Brook, but not in Gilmore Creek. Prey number per sculpin stomach declined post-flood in Gilmore Creek, but not in Garvin Brook, although dry mass of prey/fish wet mass declined post-flood in both streams. Pre-spawn sculpin displayed no patterns in reproductive fitness (gonadosomatic index, hepatosomatic index, oocyte number) among the three streams that may have been related to flooding severity the previous summer. Although sculpin diets and condition were altered significantly immediately post-flood in the more severely flooded stream, food resource recovery apparently was rapid enough to prevent longer-term impacts on sculpin condition and reproductive fitness.

The ambient air quality data for particulate matter as well as criteria of gaseous pollutants were assembled during December 2013 to December 2015 from the Continuous Air Quality Monitoring Station (CAMS) located at Agrabad, Chittagong. The observation showed that during April- October, 24 hour average concentration of PM10 and PM2.5 were within the National Ambient Air Quality Standard (NAAQS) level but it increased occasionally by more than two and a half times during the whole non-monsoon period (November-March). The highest values found of PM2.5 were 321.1 µg/m³ in January, 2013 and 220.34 µg/m³ in December 2015. Whether, the highest alarming concentration of PM10 was reported as 474 µg/m3 in January 2007. The other gaseous pollutants such as SO₂, NO₂, O₃, CO and Hydrocarbons remain well within the permissible limit except dry non-monsoon period. The yearly average increase of Air Quality Index (AQI) value indicates the growth rate of air pollution in Chittagong city. The main responsible pollutant for air pollution is found PM_2.5.

Walking School Buses (WSBs) provide a safe alternative to being driven to school. Children benefit from the contribution the exercise provides towards their daily exercise target, it gives children practical experience with respect to road safety and helps to relieve traffic congestion around the entrance to their school. Walking routes are designed largely based in road safety considerations, catchment need and the availability of parent support. However, little attention is given to the air pollution exposure experienced by children during their journey to school, despite the commuting microenvironment being an important contributor to a child’s daily air pollution exposure. This study aims to quantify the air pollution exposure experienced by children walking to school and those being driven by car. A school was chosen in Bradford, UK. Three adult participants carried out the journey to and from school each carrying a P-Trak ultrafine particle (UFP) count monitor. One participant travelled the journey to school by car while the other two walked, each on opposite sides of the road for the majority of the journey. Data collection was carried out over a period of two weeks, for a total of five journeys to school in the morning and five on the way home at the end of the school day. Results of the study suggest that car commuters experience lower levels of air pollution dose due to lower exposures and reduced commute times. The largest reductions in exposure for pedestrians can be achieved by avoiding close proximity to traffic queuing up to intersections, and, where possible, walking on the side of the road opposite the traffic, especially during the morning commuting period. Major intersections should also be avoided as they were associated with peak exposures. Steps to ensure that the phasing of lights is optimized to minimize pedestrian waiting time would also help reduce exposures. If possible, busy roads should be avoided altogether. By the careful design of WSB routes, taking into account air pollution, children will be able to experience the benefits that walking to school brings while minimizing their air pollution exposure during their commute to and from school.

Air corridors are an integral part of the advanced air mobility infrastructure. They are the virtual highways in the sky for transportation of people and cargo in the controlled airspace at an altitude of around 1000 ft. to 2000 ft. above the ground level. This paper presents fundamental insights into the design of air corridors with high operational efficiency as well as zero collisions. It begins with the definitions of air cube, skylane or track, intersection, vertiport, gate, and air corridor. Then, a multi-layered air corridor model is proposed. Traffic at intersections is analyzed in detail with examples of vehicles turning in different directions. The concept of capacity of an air corridor is introduced along with the nature of distribution of locations of vehicles in the air corridor and collision probability inside the corridor are discussed. Finally, the results of simulations of traffic flows are presented.

Optimum selectivity of enhanced oil recovery techniques would play a substantial role in the economic prosperity of petroleum industries which might be virtually eliminated unnecessary expenditures. In this paper, the simultaneous utilization of foaming agent, surfactant polymer (SP), and supercritical carbon dioxide were taken into the investigation under the miscible condition to evaluate the efficiency of each scenario on the cumulative recovery factor, water cut and pressure drop. According to the results of this experimental evaluation, SP-foam flooding had witnessed the highest blockage which is caused to have the maximum recovery factor due to the mobilization of more oil volume in the low permeable pores and cracks. Furthermore, the utilization of surfactant with supercritical carbon dioxide had experienced the least recovery factor regarding the insufficient foam generation which is led to less mobilization of oil phase in the pore throats.

Estimating ground surface PM2.5 with fine spatiotemporal resolution is a critical technique for exposure assessments in epidemiological studies of its health risks. Previous studies have utilized monitoring, satellite remote sensing or air quality modeling data to evaluate the spatiotemporal variations of PM2.5 concentrations, but such studies rarely combined these data simultaneously. We develop a three-stage model to fuse PM2.5 monitoring data, satellite-derived aerosol optical depth (AOD) and community multi-scale air quality (CMAQ) simulations together and apply it to estimate daily PM2.5 at a spatial resolution of 0.1˚ over China. Performance of the three-stage model is evaluated using a cross-validation (CV) method step by step. CV results show that the finally fused estimator of PM2.5 is in good agreement with the observational data (RMSE = 23.00 μg/m^3 and R2 = 0.72) and outperforms either AOD-retrieved PM2.5 (R2 = 0.62) or CMAQ simulations (R2 = 0.51). According to step-specific CVs, in data fusion, AOD-retrieved PM2.5 plays a key role to reduce mean bias, whereas CMAQ provides all-spacetime-covered predictions, which avoids sampling bias caused by non-random incompleteness in satellite-derived AOD. Our fused products are more capable than either CMAQ simulations or AOD-based estimates in characterizing the polluting procedure during haze episodes and thus can support both chronic and acute exposure assessments of ambient PM2.5. Based on the products, averaged concentration of annual exposure to PM2.5 was 55.75 μg/m3, while averaged count of polluted days (PM2.5 > 75 μg/m3) was 81, across China during 2014. Fused estimates will be publicly available for future health-related studies.

The interest in flying wings dates as far the early years of the aviation age. Over the 20th century, numerous attempts were made to investigate the feasibility of the concept, which demonstrated numerous early benefits: increased aerodynamic efficiency, reduced fuel consumption and lower noise and pollutant emissions compared to conventional tube and wing aircraft. However, major technical challenges prevented that type of design from entering mass production, especially with regards to structural design and manufacturing, stability and control and ride quality. In the 1990’s, a new concept, the blended wing body (BWB), was created to alleviate some of the concerns of flying wings while maintaining increased efficiency. Despite the promise, technical hurdles once again proved to be a deal breaker, and as of 2024, the only flying wing to enter serial production is the B-2 Spirit, an extremely complex and expensive aircraft. Thirty years later, as the world is quickly transitioning towards cleaner energy, the interest in the blended wing body has been renewed. The latest technological advancements in the aerospace industry should make the development of the BWB more plausible, however passenger comfort issues remain. Surprisingly, the BWB development may come from an unexpected application: as a tanker aircraft. As the U.S. Air Force is seeking a replacement to hundreds of aging tankers, a startup company was recently funded to develop the concept and build a prototype. In this study, we explore the history of blended designs from its early days, highlighting its opportunities and challenges – and why the design is an intriguing fit for application as a tanker aircraft.

Sea level rise due to global warming is a continuing and, disappointingly, accelerating process, which has already affected and will further impact coastal lowlands and the social and economic activities in these areas. Delos Island, situated in the middle of the Cyclades in the Aegean Sea, was considered the most sacred of all islands in ancient Greek culture and a trading hub for the entire eastern Mediterranean. Uninhabited since the 7th century AD, and consistently the focus of research and touristic attention, the island is designated as an archaeological site and inscribed on the Unesco World Heritage List. Previous studies on the relative sea level (rsl) changes suggest a steadily rsl rise during the last 6,300 years, starting from a sea level at -4.80±0.20m in the Late Neolithic. The seafront of the ancient city of Delos is subject to the effects of the rsl rise, which have caused significant coastline retreat and exposure to the northerly winds and waves, whereas parts of the coastal lowland where the remains of the ancient city lie are inundated, forming extended wetlands. The future impacts of rsl rise on the seafront of ancient Delos are illustrated on very high-resolution digital surface models, evaluating both the flooding risk under different climatic projections, as provided by the IPCC AR6 report, and the ongoing land subsidence, as recorded by GNSS data. An rsl rise ranging from 87cm (SSP1-2.6 scenario) to 148cm (SSP5-8.5 scenario) is anticipated by 2150, requiring both resilience strategies and adaptation solutions as well as mitigation policies to cope with the effects of climate change.

The mangrove plant Acanthus ilicifolius and its relative, A. mollis, have been previously proved to possess diverse pharmacological effects. Therefore, evaluating the differentially expressed proteins of these species under tidal flooding stress is essential to fully exploit and benefit from their medicinal values. The roots of A. ilicifolius and A. mollis were exposed to 6 h of flooding stress per day for 10 days. The dry weight, hydrogen peroxide (H2O2) content, anatomical characteristics, carbon and energy levels, and two-dimensional electrophoresis coupled with MALDI-TOF/TOF MS technology were used to reveal the divergent flooding resistant strategies. A. ilicifolius performed better under tidal flooding stress, which was reflected in the integrity of the morphological structure, more efficient use of carbon and energy, and a higher percentage of up-regulated proteins associated with carbon and energy metabolism. A. mollis could not survive in flooding conditions for a long time, as revealed by incomplete cell structures of the roots, less efficient use of carbon and energy, and a higher percentage of down-regulated proteins associated with carbon and energy metabolism. Energy provision and flux balance played a role in the flooding tolerance of A. ilicifolius and A. mollis.

This comprehensive critical review shows how green buildings and energy optimization solutions improve indoor air quality as well as environmental quality (IEQ) and human health. Electricity-efficient green buildings create a better indoor atmosphere and save electricity. Green buildings improve occupant well-being through IAQ, thermal comfort, acoustics, and lighting. Renewable energy, green construction materials, and intelligent technologies increase sustainability and reduce environmental impact. Environmental hazards, architectural design, and societal variables can improve indoor air quality and subsequently reduce health risks linked with poor air quality. The evaluation highlights the pros and cons of low-cost IAQ sensors and equipment. These devices provide valuable insights, but calibration and validation using reference equipment are necessary to ensure accuracy and reliability. Architects, engineers, environmentalists, and policymakers are essential in creating green buildings with high IEQ. Prioritizing occupant comfort, health, and productivity ensures a sustainable and healthy future for future generations. However, continual monitoring and research are needed to improve green building practices and overcome construction problems. Intelligent models for continual on-field calibration of low-cost sensors may improve performance. Green buildings benefit occupants and the environment by optimizing energy use and using IAQ monitoring technologies.

This article examines air sampling as an environmental surveillance strategy for early pathogen detection and offers a preliminary comparison of air and wastewater surveillance. Air sampling involves collecting bioaerosols to analyze the microbial composition of the air, utilizing techniques like PCR and metagenomic sequencing. Air sampling appears especially promising for detecting respiratory pathogens and highly transmissible pandemic agents, as these spread primarily via aerosols and droplets. The article details various air sampling techniques, their efficiency, and practical considerations, categorizing them into filtration, impaction, impingement, electrostatic precipitation, and condensation methods. It also explores the composition of airborne microbes, emphasizing the low concentration of viral nucleic acids and the challenges this poses for metagenomic sequencing. The selection of sampling locations, including indoor environments and airplanes, is discussed as critical for effective pathogen detection. Finally, the article contrasts air and wastewater sampling, concluding that while both methods should ideally be explored as layered defenses, air sampling does not collectively appear more promising than wastewater sampling.

Urban air quality is increasingly becoming a cause for concern for the health of the human population. The poor air quality is already wreaking havoc in major cities of the world, where serious health issues and reduction of average human life by a factor of years are reported. The air quality in developing countries can become worse as they undergo development. The urban air quality varies non-linearly depending upon the various factors such as land use, industrialization, waste disposal, traffic volume, etc. To address this problem, it is necessary to look at the plethora of available literature from multiple perspectives such as types and sources of pollutants, meteorology, urban mobility, urban planning and development, health care, economics, etc. In this paper, we provide a comprehensive survey of the state-of-the-art in urban air quality. We first review the fundamental background on air quality and present the emerging landscape of urban air quality. We then explore the available literature from multiple urban air quality measurement projects and provides the insights uncovered in them. We then take a look at the sources that are significantly contributing to polluting the air quality. Finally, we highlight open issues and research challenges in dealing with urban air pollution.

Environment pollution is the major problem for all the sectors. In environment pollution there are different types of pollution is included such as air pollution, water pollution, soil pollution etc. In these types of pollution most of it is air pollution. There are many reasons for pollution of air. Human advance in science but one of the major draw backs of science is the pollution of air rapidly. Air pollution is injurious to health. Every year a large number of people died for the effects of air pollution. It can be improved in many ways among these ways technology upgradation plays a major role here. There are various method that prevent air pollution. Many researchers tried and is trying to prevent the air pollution in many ways. In this review paper I summarise the existing research on different ways for preventing air pollution in addition I will discuss the gaps and future aspect on this topic.

Pyrolysis is a combustion process of woody biomass conducted under low or no oxygen conditions. New innovations and the need to limit open burning has resulted in numerous mobile and fixed plant pyrolysis methods that burn a variety of woody residues. Production technologies that reduce the need for open burning, the main source of potential pollutants, fall under the regulations in the Clean Air Act of 1990. This Act is the legal instrument to regulate air pollution at its source across the United States of America and it is implemented and enforced through the Environmental Protection Agency, in coordination with sister agencies. One newer innovation for reducing woody residues and emissions is an air curtain incinerator. Currently, the Clean Air Act regulates stationary solid waste incinerators, and this is also applied to mobile air curtain incinerators burning woody biomass. However, other woody biochar production methods (e.g., flame cap kilns) are not subject to these regulations. Discrepancies in the interpretation of definitions related to incineration and pyrolysis and the myriad of differences related to stationary and mobile air curtain incinerators, type of waste wood from construction activities, forest residues, and other types of clean wood make the permitting regulations confusing as permits can vary by jurisdiction. This review summarizes the current policies, regulations, and directives related to in-woods biochar production and the required permits.

In this work, a novel heterojunction based on ZnSnO3/ZnO nanofibers was prepared using electrospinning method. The crystal, structural and surface compositional properties of sample based on ZnSnO3 and ZnSnO3/ZnO composite nanofibers were investigated by X-ray diffractometer (XRD), Scanning electron microscope (SEM), X-ray photoelectron spectrometer (XPS) and Brunauer-Emmett-Teller (BET). Compared to pure ZnSnO3 nanofibers, the ZnSnO3/ZnO heterostructure nanofibers display high sensitivity and selectivity response with fast response towards ethanol gas at low operational temperature. The sensitivity response of sensor based on ZnSnO3/ZnO composite nanofibers were 19.6 towards 50 ppm ethanol gas at 225°C, which was about 1.5 times superior than that of pure ZnSnO3 nanofibers, which can be owed mainly to the presence of oxygen vacancies and the synergistic effect between ZnSnO3 and ZnO.

In this study, the relationship between air diffusivity and permeability in cementitious materials was investigated. First, we derived an equation to correlate air diffusivity and permeability in a straight circular tube. Then, we reviewed existing studies that measured both air diffusivity and permeability and compared reported data and calculated values to verify the applicability of the derived equation to cementitious materials. Although a correction factor was not used, the two sets of data showed good agreement quantitatively. This indicates that the derived equation can be applied to cementitious materials including concrete, and measured air diffusivity can be converted to permeability of concrete and vice versa using the derived equation.

This paper investigates the effects of air void topology on hydraulic conductivity in asphalt mixtures with porosity in the range 14%-31%. Virtual asphalt pore networks were generated using the Intersected Stacked Air voids (ISA) method, with its parameters being automatically adjusted by the means of a differential evolution optimisation algorithm, and then 3D printed using transparent resin. Permeability tests were conducted on the resin samples to understand the effects of pore topology on hydraulic conductivity. Moreover, the pore networks generated virtually were compared to real asphalt pore networks captured via X-ray Computed Tomography (CT) scans. The optimised ISA method was able to generate realistic 3D pore networks corresponding to those seen in asphalt mixtures in term of visual, topological, statistical and air void shape properties. It was found that, in the range of porous asphalt materials investigated in this research, the high dispersion in hydraulic conductivity at constant air void content is a function of the average air void diameter. Finally, the relationship between average void diameter and the maximum aggregate size and gradation in porous asphalt materials was investigated.

International literature data report that the increase of infectious risk may be due to heating, ventilation and air conditioning (HVAC) systems contaminated by airborne pathogens. Moreover, the presence of complex rotating dehumidification wheels (RDWs) may complicate the cleaning and disinfection procedures of the HVAC systems. We evaluated the efficacy of a disinfection strategy applied to the RDW of two hospitals HVAC systems. Hospitals have 4 RDW systems related to the surgical areas (SA1 and SA2) and to the intensive and sub-intensive cares (IC and sIC). Microbiological air and surfaces analysis were performed in HVAC systems, before and after the disinfection treatment. Hydrogen peroxide (12%) with silver ions (10 mg/L) was aerosolized in all the air sampling points, located close to the RDW device. After the air disinfection procedure, reductions of total microbial counts at 22°C and fungi were achieved in SA2 and IC HVAC systems. An Aspergillus fumigatus contamination (6 CFU/500L), detected in one air sample collected in the IC HVAC system, was eradicated after the disinfection. Surface samples proved a good microbiological quality. Results suggest the need of a disinfection procedure aimed to improve the microbiological quality of the complex HVAC systems, mostly in surgical and intensive care areas.

: During the period of COVID-19, the Chinese government implemented a series of actions to prevent the spread of the virus. It is noticed that these preventive actions have generated positive effects on air pollution in Wuhan and Beijing. And, due to the differences in city functions, geographic locations, meteorological conditions, and preventive action details between the two cities, noticeable difference is observed on how they reduced air pollution. This unfortunate incident has become a social sample for studying the industrial and livelihood activities impact on air pollution, otherwise would be highly impossible. This paper starts from observing data from NASA's real-time fine particulate matter (PM2.5) and NO2, and comparing the air pollution in this special time domain with previous years. It is discovered that both PM2.5 and NO2 have been reduced in Wuhan, while only NO2 has significant reduction in Beijing, during the COVID-19 responses. This suggests that the human activity suppression by the COVID-19 control yields different effects on different pollutants and in different cities. Possible reasons for such effects are analysed by considering the public health control levels as well as the pollutant migration, industrial activities, and the weather conditions.

The information technology has brought in a revolution in the area of digital agriculture and hydrological modeling . With the advent of IOT and AI such as machine learning is now capable of Predicating flood forecast , drought forecast and farms based water predications. In this article various machine learning algorithms , multiple sensors for environmental and agricultural has been proposed and used . The purpose is to acquire data of soil moisture , temperature , crop stages, irrigation and precipitation on a region constitute of two farms and then performed machine learning predications for total discharge predications at farms outlets so that in case of excessive rainfall or an irrigation event the water is adjusted in the second nearby farm or reroute to a reservoir for future use to avoid flooding. The focus is mostly to work on the concept and building of an andriod -ardiuno based mobile application for the endusers (agricultural system analyst, farmers) to provide an ease. The whole system of smart agricultural based on two farms and reservoir will provide an efficient ,fully automatic, proactive and decision support system to save water waste and reuse. In future the work is also in progress for developing a desktop based application .

This work investigates spatial and temporal distributions of hydroxyl, OH, in laser-plasma in laboratory air at standard ambient temperature and pressure. Of interest are determination of temperature and density of OH and establishment of a correlation of molecular OH emission spectra with shadow graphs for time delays of 50 to 100 microsecond, analogous to previous work on shadow graph and emission spectroscopy correlation for cynaide, CN, in gas mixtures and for time delays of the order of 1 microsecond. Wavelength- and sensitivity- corrected spatiotemporal data analysis focuses on temperature inferences using molecular OH emission spectroscopy. Near-ir radiation from a Q-switched laser device initiates optical breakdown in laboratory air. The laser device provides 6 nanosecond, up to 850 milli Joule pulses at a wavelength of 1064 nanometer, and focal irradiance in the range of 1 to 10 Tera Watt per centimeter-squared. Frequency doubled beams are utilized for capturing shadow graphs for visualization of the breakdown kernel at time delays in the range of 0.1 to 100 microsecond. OH emission spectra of the laser plasma, spatially resolved along the slit dimension, are recorded in the wavelength range of 298 nm to 321 nm, and with gate widths adjusted to 10 microsecond for the intensified charge-coupled device that is mounted at the exit plane of a 0.64 m Czerny-Turner configuration spectrometer. Diatomic OH signals occur due to recombination of the plasma and are clearly distinguishable for time delays larger than 50 microsecond, but are masked by spectra of N2 early in the plasma decay.

We describe a novel machine that uses the greater-than-100% efficiency of air/ground-source heat pumps to recursively generate electricity via steam-powered generators, taking thermal energy from the ambient environment to convert into electrical power. The invention of a machines that generate clean power at low costs will be fundamental to the future of electricity. We estimate efficiency and calculate minimum efficiencies for unknown parts to consider the applicability of this machine to the real world.

Growing popularity of buildings with integrated sub-systems, requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using geothermal heat storage parallel to the direct outdoor air intake with additional treatment in the mechanical room as a part of building automatic control system. Earth Air Heat Exchanger (EAHX) has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we have examined two nearly identical EAHX systems, one placed in ground next to the building and the other under the basement slab. In another project, we have reinforced the ground storage action by heat exchanger placed on the return pipes of the hydronic heating system. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX could be placed under the house or near the basement foundation that is using an exterior basement insulation.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Abstract: The air pollution dispersion modelling via spatial analyses (Land Use Regression – LUR) is an alternative approach to the air quality assessment to the standard air pollution dispersion modelling techniques. Its advantages are mainly much simpler mathematical apparatus, quicker and simpler calculations and a possibility to incorporate other factors affecting pollutant’s concentration. The goal of the study was to model the PM10 particles dispersion modelling via spatial analyses v in Czech-Polish border area of Upper Silesian industrial agglomeration and compare results with results of the standard Gaussian dispersion model SYMOS’97. Results show that standard Gaussian model with the same data as the LUR model gives better results (determination coefficient 71% for Gaussian model to 48% for LUR model). When factors of the land cover and were included into the LUR model, the LUR model results were significantly improved (65% determination coefficient) to the level comparable with Gaussian model. The hybrid approach combining the Gaussian model with the LUR gives superior quality of results (65% determination coefficient).

Air pollution knows no boundaries, which means for a city or a region to attain clean air standards, must not only look at the emission sources within its own administrative boundary, but also at sources in the immediate vicinity and those originating from long-range transport. And there is a limit to how much area can be explored to evaluate, govern, and manage as designated airsheds for cities and larger regions. This paper discusses the need from an official airshed framework for India’s air quality management, urban airsheds designated for India’s 131 non-attainment cities under the national clean air programme, and proposes climatically and geographically appropriate regional airsheds to support long-term planning. Between 28 states, eight union territories, 36 meteorological sub-regional divisions, and six regional meteorological departments, establishing the proposed 15 regional airsheds for integrated and collaborative air quality management across India is a unique opportunity.

The educational and play-related activities of children are proceeded mainly indoors in a kin-dergarten. The exposure of children to high concentrations of PM2.5 and CO2 indoors have leaded to various harmful effects and negatively impact educational outcomes in a kindergarten. Therefore, this study presents a numerical model of CO2 and PM2.5 concentration based on two classrooms in a kindergarten. Using this numerical model, we present different scenarios of oper-ating mechanical ventilation and air purifiers in kindergartens with the aim of optimizing for reducing the concentrations of CO2 and PM2.5. We found that the amount of ventilation required to maintain good air quality, per child, was approximately 20.4 m3/h. However, we also found that as the amount of ventilation increased, so did the concentration of indoor PM2.5; we found that this issue can be resolved through the use of a high-grade filter (i.e., a MERV 13 grade filter with a collection efficiency of 75%). This study provides a scientific basis for reducing PM2.5concentrations in kindergartens, while keeping CO2 levels low.

This study proposes an image recognition method to assist swine farm managers in collecting health data related to pig feeding and excretion. Analyzing the correlation between sow health data and indoor air quality in the pigsties revealed significant influences of air quality indicators on sow health. Increased levels of TVOC, CO2, and temperature were found to negatively affect feeding health, while increased temperature, humidity, and PM10 were found to negatively impact excretion health. These findings provide a basis for evaluating variables when constructing future sow disease prediction models. Analyzing the correlation between pig health status and air quality can help swine farm managers improve sow production environments, reduce disease risks, enhance production efficiency, and provide valuable insights for future research on disease prediction models.

Multiple social and environmental justice concerns are linked to urban form such as the distribution of socioeconomic class populations, healthcare spending, air pollution exposure, and human mobility. This study used 1m resolved LIDAR data to characterize land use in Salt Lake County, Utah and associate it with sociodemographic and air quality data at the census block group and zip code levels. We found that increasing tree cover was associated with higher per capita income and lower minority populations while increasing built cover was linked to lower per capita income and higher minority populations. Air quality showed less strong correlations, however, decreased non irrigated cover, increased built cover, and higher amounts of households living under poverty was related to higher long-term PM2.5 exposure. Several policy efforts have been undertaken to improve air quality and reduce negative health outcomes in Utah which are being informed by regulatory and research grade air quality sensors.

Climate data are important in building a hydrological risk assessment model. The ClimInonda web application enables interactive and dynamic visualizations of different data collected from different weather stations in the study area on a single platform, allowing users to explore and analyze data in an easy way. This can assist decision-makers and stakeholders in understanding the current state of the environment and in identifying areas of flooding risk. Visualizations can include different types of data, such as satellite imagery, weather data, and terrain data, and can be displayed using various techniques, such as heat maps, contour maps, and 3D models by providing easy-to-understand visualizations. The different stations of the Gafsa and Kasserine governorates in the study area are included and other stations of the Algerian territory (Tebessa governorate) are incorporated. This web application also provides the capability to include each user's stations.

Most people living in Europe's cities are still exposed to levels of air pollution deemed harmful by the World Health Organization. In the modern world, air pollution is the foremost concern because of its impact in human health and economy. This strong connection appears gaining a lot of concern, driven by new installed low-cost electrochemical sensors monitoring systems. Highly accuracy, real-time monitoring, daily and yearly statistics, data access from experts or simple users, low-cost equipment and forecasting needs, enforce the market to develop new air quality monitoring systems using advanced technologies and protocols. In this study, a comparison via low-cost electrochemical sensors and of static, fixed site measurement monitoring station, is taking place in Athens, Greece, along with the data quality and Air Quality Index (AQI) including data accuracy and quality of data concerning adverse health effects due to air pollution. The findings presented in this work, relate to different flexible and affordable alternatives adopted during the evaluation and calibration of low-cost gas sensors for the monitoring. The significance of the positive results is particularly useful, especially considering the founding for interference, environmental conditions affections and air quality information including indexes and health recommendations for a specific location.

Ethylene Oxide (EtO) is a colorless, flammable gas at room temperature, produced by the catalytic oxidation of ethylene. EtO is widely used by medical sterilization facilities to clean medical supplies and equipment. Recent epidemiological studies showed that EtO is a more potent carcinogen than previously documented, leading the Environmental Protection Agency (EPA) to update, in December 2016, the inhalation unit risk estimate for EtO. This resulted in the identification of EtO as a potential health concern in several areas across the US, including the state of Utah. The geography surrounding Salt Lake Valley creates a bowl; ideal for collecting air pollution emissions. The region often experiences inversion episodes which inhibit vertical mixing and cause an accumulation of air pollutants, leading to unhealthy pollution levels. Using the EPA's dispersion modeling software, AERMOD, this study estimated EtO concentrations through facility stack and fugitive emissions modeling results. These values were compared with those of canister-based concentrations from ambient air samples taken near a medical device sterilization facility in the Salt Lake Valley. Stainless steel, whole-air passivated canisters were used to collect 24-hour ambient concentration samples of EtO. Eight locations surrounding a Salt Lake Valley medical device sterilization facility and four background sites were chosen to measure the ambient concentrations. Accounting for potential atmospheric impacts on EtO, measurements were sampled in winter 2022 (January-March) and summer 2022 (July-September). The modeled EtO concentrations were adjusted to account for background values associated with the winter or summer data. Then the two methodologies were compared using a Wilcoxon Sign-ranked, paired test. The statistical analysis resulted in six of the eight sample locations surrounding the sterilization facility being significantly different when comparing canister-based measurements of ambient EtO to modeled estimates. Canister-based measurements taken at sites one, three, and four were statistically greater than the modeled estimates, while sites two, five, and seven were statistically less than the modeled estimates. Also, the summer background value calculated was almost 2.5 times greater than the winter. The results do not suggest whether one method is more or less conservative than the other. In conclusion, the five of the closest sites and site seven were statistically different when comparing measured and modeled ambient concentrations of EtO. The comparison results do not clearly indicate if a correction factor could be derived for future human exposure to cancer risk assessment modeling. However, it is reasonable that the closer to the sterilization facility, the more total EtO exposure will be realized.

Mediterranean Sea are dynamic habitats in which human activities have been conducted for centuries and which feature micro-tidal environments with about 0.40 m of range. For this reason, human settlements are still concentrated along a narrow coastline strip, where any change in the sea level and coastal dynamics may impact anthropic activities. We analyzed light detection and ranging (LiDAR) and Copernicus Earth Observation data. Aim of this research is to provide estimates and detailed maps (in three coastal plain of Sardinia (Italy) and in the Pontina Plain (southern Latium, Italy) of: i) the past marine trasgression occurred during MIS 5.5 higstand 119 kyrss BP; ii) the coastline regression occurred during the last glacial maximum MIS 2 (21.5 krs cal BP) and iii) the potential marine submersion for 2100 and 2300. The objective of this multidisciplinary study is to provide maps of sea-level rise future scenarios using the IPCC RCP 8.5 2019 [1]projections and glacio-hydro-isostatic movements for the above selected coastal zones, which are the locations of touristic resorts, railways, and heritage sites. We estimated a potential loss of land for the above areas of between about 146 km² (IPCC 2019-RCP8.5 scenario [1]) and 637 km² along a coastline length of about 268 km.

Air pollution has been a major environmental issue worldwide from the last few decades. It is a man-made issue that has a serious harmful impact on the environment and the health of humans. There are different sources of emission, but industrial processes and motor vehicles contribute to a chief part of air pollution. It has acute as well as chronic effects on the health of humans and affects different organs. It is thought the main environmental risk factor in the incidence and progression of several diseases such as lung cancer, asthma, Alzheimer's and Parkinson's diseases. Long-term exposure to air pollution has different toxicological impacts on humans such as respiratory and cardiovascular diseases, neuropsychiatric complications, eye irritation and skin diseases. As per the study by the World Health Organization (WHO), nitrogen oxides (NOx), carbon monoxide (CO), ozone (O₃), sulfur dioxide (SO₂), volatile organic compounds (VOCs) and heavy metals are the major air contaminants. These pollutants are different in their properties, composition and time of disintegration. The aim of this study is to review the different sources, types, impacts, challenges and mitigation of air pollution in detail.

Cigarette smoking and air pollution (particulate matter) are recognized as two major etiological factors for lung cancer. Of all the risk factors, cigarette smoking is significantly associated with lung carcinogenesis. The main mechanism lies in the metabolically activated carcinogens (majorly polycyclic aromatic hydrocarbons and nitrosamines), which could covalently bind with DNA molecules and lead to irreversible mutations in pivotal cancer genes, such as TP53 and KRAS. Another major etiological factor for lung cancer is air pollution, which is with complex compositions and ubiquitous in daily life, especially in developing countries as China and India. The latest literatures on lung cancer epidemiology and etiology have been briefly summarized and reviewed in this work.

This study examines the relation between ambient air pollution and emergency department (ED) visits due to certain infectious diseases in Toronto, Canada. The National Ambulatory Care Reporting System database was used to draw the corresponding health cases. Daily data on ED visits, ambient air pollution concentration levels, and weather conditions during the period from April 2004 to December 2015 (4,292 days in total) were linked together and used in statistical models. Six air pollutants (fine particulate matter PM2.5, CO, NO2, SO2, ozone O3 as a daily average, and ozone O3-8 hour ozone, as a maximum eight hour average) were investigated. In addition, the Air Quality Health Index (combining NO2, O3, and PM2.5) was also considered. The time-stratified case-crossover technique was applied in the study design. Conditional Poisson models were created using the daily counts of ED visit data. The considered factors, air pollutants and weather, were lagged by the same number of days, from 0 to 14. In the period of the study 339,644 ED visits were identified; 177,619 for females and 162,025 for males. For each air pollutant 270 models were realized (15 lags x 18 strata). Ambient air pollution concentrations lagged by 2, 3, and 5 days have the highest impact on ED visits, with 34, 32, and 35 positive associations, respectively. For all patients and an increase in a one interquartile range (IQR=1.2 ppb) of sulphur dioxide, the following values of the relative risks (RR) were estimated: RR=1.005 (95% confidence interval: 0.998, 1.013), 1.008 (1.001, 1.016), 1.009 (1.001, 1.016), 1.011 (1.004, 1.019), 1.007 (0.987, 1.028), and 1.009 (1.002, 1.016) for lags from 0 to 5, respectively. The results suggest that exposures for certain air pollutants (mainly CO, O3, and SO2) in urban environment affect the number of ED visits related to infectious diseases.

Correlations between the air permeability coefficient and various pore structure indicators in cementitious materials were examined to determine the pore structure indicator that best evaluated air permeability using data from previous studies of air permeabilities and pore structures. The determination coefficients of air permeability with total pore volume, critical pore diameter, and ordinary threshold pore diameter were low, although these have often been used as indicators. The median and threshold pore diameters obtained by percolation theory showed high determination coefficients. The equation using the threshold pore diameter better estimated the air permeability coefficient than the Katz–Thompson equation.

In this paper, we tackle air quality forecasting by using machine learning approaches to predict the hourly concentration of air pollutants (e.g., Ozone, PM_2.5 and Sulfur Dioxide). Machine learning, as one of the most popular techniques, is able to efficiently train a model on big data by using large-scale optimization algorithms. Although there exists some works applying machine learning to air quality prediction, most of the prior studies are restricted to small scale data and simply train standard regression models (linear or non-linear) to predict the hourly air pollution concentration. In this work, we propose refined models to predict the hourly air pollution concentration based on meteorological data of previous days by formulating the prediction of 24 hours as a multi-task learning problem. It enables us to select a good model with different regularization techniques. We propose a useful regularization by enforcing the prediction models of consecutive hours to be close to each other, and compare with several typical regularizations for multi-task learning including standard Frobenius norm regularization, nuclear norm regularization, ℓ_2,1 norm regularization. Our experiments show the proposed formulations and regularization achieve better performance than existing standard regression models and existing regularizations.

Air quality is one of the most concerning problems in major industrialized cities in the world. Prediction of future air quality is highly relevant to public health. In some big cities, multiple air quality measurement stations are deployed at different locations to monitor air pollutants, such as NO2, CO, PM 2.5 and PM 10, over time. At every monitoring time stamp t, we observe one station×feature matrix xt of the pollutant data, which represents a spatio–temporal process. Traditional methods on prediction of air quality typically use data from one station or can only predict a single pollutant (such as PM 2.5) at a time, which ignores the spatial correlation among different stations. Moreover, the air pollution data are typically highly nonstationary, We propose a de-trending graph convolutional LSTM (long short term memory) to continuously predict the whole station×feature matrix in the next 1 to 48 hours, which not only captures the spatial dependency among multiple stations by replacing an inner product with convolution, but also incorporates the de-trending signals (transform a nonstationary process to a stationary one by differencing the data) into our model. Experiments on the air quality data of the city Chengdu and multiple major cities in China demonstrate the feasibility of our method and show promising results.

Reinforcement learning is used for air combat problems in recent years, and the idea of curriculum learning is often used for reinforcement learning, but traditional curriculum learning suffers from the problem of plasticity loss in neural networks. Plasticity loss is the difficulty of learning new knowledge after the network has converged. To this end, we propose a motivational curriculum learning distributed proximal policy optimization (MCLDPPO) algorithm, through which agents trained can significantly outperform the predictive game tree and mainstream reinforcement learning methods. The motivational curriculum learning is to help the agent gradually improve their combat ability by observing the agent's unsatisfactory performance and providing corresponding rewards as a guide. Additionally, a complete tactical maneuver is encapsulated based on existing air combat knowledge, and through the flexible use of these maneuvers, some tactics beyond human knowledge can be realized. In addition, we designed an interruption mechanism for the agent to increase the frequency of decision-making when the agent faces an emergency. When the number of threats the agent receives changes, the current action will be interrupted to reacquire observations and make decisions again. Using the interruption mechanism can significantly improve the ability of the agent. To simulate actual air combat better, we built an air combat environment based on digital twin technology to create an air combat engine core such as missiles and radars. Based on this environment, we develop a distributed intelligent training system that employs Redis as the cache and obtains the data generated in the distributed environment through a multi-threaded TCP/IP protocol, which significantly increases the training data throughput and helps the agent accelerates convergence. The experimental results demonstrate that the agent can fully exploit the situational information to make reasonable decisions and affords air combat tactical adaption, verifying the effectiveness of the algorithmic framework proposed in this paper.

The growing need to use renewable sources and the current difficulty in spreading the electricity grid in a widespread manner raise the question of how to respond to the need for more electricity immediately. The idea behind this study is to power a horizontal axis wind turbine with the air flow generated for cooling a stationary internal combustion engine. The power extracted from this solution is significantly lower than that of the internal combustion engine (about 0.3%) and could be advantageous only in limited contexts. Installation costs are limited because many elements deriving from wind variability can be removed or simplified.

Since World War I, the commercial aviation industry has seen many improvements that now allow people and goods to reach the other side of the world in few hours, consuming much less fuel than in recent decades. Improvements in cargo capacity and energy efficiency were significant and, in this scenario, commercial airlines were able to thrive and bring great benefits to world economy. However, this sector is facing environmental challenges due to the intensive use of aviation fuel. Brazil is one of the largest domestic air passenger markets in the world and still has great growth potential, considering its economic potential and territorial dimensions: roughly the same size as the US and twice the size of the European Union. This paper discusses partial productivity of jet fuel in Brazilian domestic aviation and proposes an econometric method to support public regulators and airlines decisions. The proposed model uses variables such as aircraft size, route characteristics and idle flight capacity in a panel data analysis. The results show that reducing idle capacity is one of the best ways to achieve better short-term fuel efficiency and therefore will reduce environmental impacts and have positive economic effects on commercial air transport activities.

While previous research has shown the use of attachable air-caps on windows to efficiently reduce a building’s energy consumption, the air-caps considered had to be attached to the entire window’s surface, thus limiting the occupants’ view and creating the inconvenience of needing to detach and attach the air-caps. In this study, a window-mounted air-cap roller module using Velcro tape that may be easily attached, detached, and rolled up or down was developed and performance tested in a full-scale test bed. It was found that as the area of the air-caps attached on a window increased, the required indoor lighting energy increased. However, the window insulation improved, thus reducing the cooling and heating energy needed. Attaching the air-caps to the entire window surface effectively reduced the building’s energy consumption, but views through the window may be disturbed. Thus, the developed window-mounted air-caps enable an occupant to reduce the building energy consumption and maintain their view according to their need. The findings of this study may contribute to a reduction in building energy consumption without sacrificing a pleasant indoor environment. Further studies may be needed to verify their efficacy under varying indoor and outdoor conditions.

In order to solve the problem of the poor oil displacement effect of high molecular weight alkali/surfactant/polymer (ASP) solution in low permeability reservoirs, Daqing Oilfield uses a partial quality tool to improve the oil displacement effect in low permeability reservoirs. Without changing the oil displacement capability of high molecular weight ASP solution in high permeability oil layers, the ASP solution is actively sheared in low permeability oil layers by using a partial quality tool to increase the injection capability of the solution and improve the overall oil recovery. In order to study the ability of the partial quality tool to improve the oil displacement effect, firstly, the matching degree of high molecular weight ASP solution to low permeability cores is studied, and the ability of quality control tools to change the molecular weight is studied. Then, experimental research on the pressure and oil displacement effect of high molecular weight ASP solution before and after the actions of the partial quality tool is carried out. The results show that ASP solutions with molecular weights of 1900 × 104 and 2500 × 104 have a poor oil displacement effect in low permeability reservoirs. After the action of the partial quality tool, the injection pressure is reduced by 5.22 MPa, and the oil recovery is increased by 7.79%. The injection pressure of the ASP solution after shearing by the partial quality tool is lower than that of the ASP solution with the same molecular weight and concentration without shearing, but the oil recovery is lower. On the whole, the use of the partial quality tool can obviously improve the oil displacement effect in low permeability reservoirs.

In the last decades, numerous studies indicated the substantial role semiconductors could play in photocatalytic processes for environmental applications. Materials that contain a semi-conductor as a photo-catalyst have a semi-permanent capacity for removing harmful gases from the ambient air. In the present work, the focus is on TiO2. Heterogeneous photo-catalysis using TiO2 leads to the degradation of NO/NO2, benzene, toluene, and other priority air pollutants once in contact with the semiconductor surface. Preliminary evidence indicates that TiO2 containing construction materials and paints efficiently destroy the ozone precursors NO and NO2 up to 80% and 30%, respectively. Therefore, the development of innovative coatings containing TiO2 as a photo-catalyst was in the foreground of research activities with the aim to be used as building and construction materials mainly outdoors, e.g. on building facades in high traffic roads for the degradation of priority air pollutants (NOx and volatile organic compounds) in the polluted urban atmosphere. Though the advantages connected with the application of TiO2 due to its band gap of 3.2 eV are limited. TiO2 is effective only in the UV-region (ca. 5%) of the solar spectrum with wavelengths λ

This paper deals with a method of calculating the self and mutual inductances of various air coils located arbitrarily in space. Known elementary solutions (the Biot-Savart formulas) were used to determine the magnetic field of infinitely thin current loops and infinitely thin wires of finite length linking magnetically other coils. Unlike commonly used algorithms, these elementary solutions were not extensively transformed analytically but were used to perform calculations by direct numerical integration. This enabled very quick and accurate obtaining of the self-inductance values as well as determining the dependence of mutual inductances on the position of both coils. This method allows analysis of different coil configurations (misaligned coils, inclined to each other, etc.) that other methods do not cover. It also enables the determination of the forces acting on the coils, as well as the calculation of the magnetic field distribution from any coil configuration. The obtained results were compared with those presented by other authors.

Fiber distributed optical fiber acoustic sensor (DAS) is generally used in distributed long-distance acoustic/vibration measurement. We found that DAS with excellent performance of low self-noise and anti-fading in combination with the plastic structure in daily life as an acoustic transducer can achieve high-sensitivity acoustic measurement at a single point rather than designing a state-of-the-art acoustic transducer or using special enhanced scattering fiber. The simple acoustic transducer we proposed for DAS can reach the sensitivity level of -106.5dB re. 1rad/μPa at a sensing range of 5.1 km, which can meet many demands on the industrial site.

Currently available data are consistent with increased severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2) replication at temperatures encountered in the upper airways (25–33°C when breathing room temperature air, 25°C) compared to those in the lower airways (37°C). One factor that may contribute to more rapid viral growth in the upper airways is the exponential increase in SARS-CoV-2 stability that occurs with reductions in temperature, as measured in vitro. Because SARS-CoV-2 frequently initiates infection in the upper airways before spreading through the body, increased upper airway viral growth early in the disease course may result in more rapid progression of disease and potentially contribute to more severe outcomes. Similarly, higher SARS-CoV-2 viral titer in the upper airways likely supports more efficient transmission. Conversely, the possible significance of air temperature to upper airway viral growth suggests that prolonged delivery of heated air might represent a preventative measure and prophylactic treatment for coronavirus disease 2019.

In the past two decades, acoustic metamaterials have garnered much attention owing to their unique functional characteristics, which is difficult to be found in naturally available materials. The acoustic metamaterials have demonstrated to exhibit excellent acoustical characteristics that paved a new pathway for researchers to develop effective solutions for a wide variety of multifunctional applications such as low-frequency sound attenuation, sound wave manipulation, energy harvesting, acoustic focusing, acoustic cloaking, biomedical acoustics, and topological acoustics. This review provides an update on the acoustic metamaterials' recent progress for simultaneous sound attenuation and air ventilation performances. Several variants of acoustic metamaterials, such as locally resonant structures, space-coiling, holey and labyrinthine metamaterials, and Fano resonant materials, are discussed briefly. Finally, the current challenges and future outlook in this emerging field is discussed as well.