As the carbon storage capacity of timber is recognized, there is growing interest in timber and wooden structures as a solution to various environmental problems. The use of Korean timber with substantial carbon storage capacity is required to reduce Korean carbon emissions and circulate timber resources. In this study, fire tests were conducted to investigate the charring properties of glued laminated timber columns made of Korean larch. The fire tests were conducted under both load-bearing and non-load-bearing conditions. The fire test results showed that the charring depth was affected by the corners of the section, and that the load ratio had an insignificant influence on the charring depth when the load ratio was 0.9 or less. This study provides data that can be used to compare the charring properties of laminated wood produced using South Korean larch with the charring properties of foreign standards. This provides reference data for developing fire-resistant design standards for timber structures made from South Korean timber.

One of the relevant goals in forging technologies is simplifying the existing process and developing new processes that can retain the original or very close to the original dimensions and billet shape after the end of the deformation cycle. This study attempts to develop a forging equipment design that provides alternating cyclic loading; the alternate cyclic forging (ACF) method is proposed. To preliminary evaluate the ACF and study the plastic deformation behavior, numerical simulation via finite element modeling (FEM) was conducted using DEFORM-3D. The main attention was paid to the metal flow characteristics, effective strain and stress distribution, and the forging load. The ACF results in non-uniform metal flow with the formation of diagonal and vortex flows were demonstrated. Maximum effective strains and stresses zones are localized at two points of the billet contact with the surface of the tooling container and at two points of the interface between the punches. It was also assumed that reducing the contact area between the punch and the billet using separate semi-cylindrical punches can reduce the forging load. Preliminary finite element analysis (FEA) results of the proposed process after four successive steps of the deformation cycle confirmed the feasibility of its general implementation.

New antimicrobial approaches are essential to counter antimicrobial resistance. The drug development pipeline is exhausted with emergence of resistance resulting in unsuccessful trials. The lack of an effective drug developed from the conventional drug portfolio has mandated the introspection into the list of potentially effective unconventional alternate antimicrobial molecules. Alternate therapies, that are clinically explicable forms include monoclonal antibodies, antimicrobial peptides, aptamers and phages. Clinical diagnostics optimizes the drug delivery. In the era of diagnostic-based applications, it is logical to draw diagnostic based treatment for infectious diseases. Selection criteria of alternate therapeutics in infectious disease include detection, monitoring of response and resistance mechanism identification. Integrating these diagnostic applications is disruptive to the traditional therapeutic development. The challenges and mitigation methods need to be noted. Applying the goals of clinical pharmacokinetics that include enhancing efficacy and decreasing toxicity of drug therapy this review analyses the strong correlation of alternate antimicrobial therapeutics in infectious diseases. The relationship between drug concentration and the resulting effect defined by the pharmacodynamic parameters are also analyzed. This review analyzes the perspectives of aligning diagnostic initiatives into the use of alternate therapeutics with a particular focus on companion diagnostic applications in infectious diseases.

(1) Background: Since microplastics in the aquatic environment are difficult to prevent and can cause adverse physiological and biochemical reactions to various organisms, we aimed to analyze the effectiveness of an eco-friendly removal method using aquatic plants with high ornamental value and excellent water purification ability. (2) Methods: Iris pseudacorus and Lythrum anceps were planted in tap water contaminated with microplastics to analyze the removal rate and root adsorption of microplastics. (3) Results: The amount of microplastics in the planting boxes of Iris pseudacorus and Lythrum anceps was significantly reduced, and the adsorption of microplastics on the roots was confirmed. (4) Conclusions: It was found that the removal of microplastics in water by aquatic plants is effective and that microplastic pollution does not significantly affect plant growth. However, the removal of microplastics by adsorption on plant roots may be affected by various environmental factors, so it is necessary to consider various limitations.

Introduction: In the recent years alternate day dosing has been recommended in iron deficieny treatment. The aim of this study is to compare the efficacy and side effects of oral iron treatments given daily 1x1, alternate day 1x1 and 2x1 alternate day dosing in iron deficieny anemia patients. Methods: A total of 52 patients with a diagnosis of iron deficiency anemia with serum ferritin level of 25 µg/L or less were included in this retrospective study. Statistical analyzes were done with SPSS V.25. Results: The patients included in our study were between the ages of 18-51. All of the patients included in the study were female. A statistically significant increase was found between 0-14 days(p<0.001), 14-28 days(p<0.001) and 0-28 days(p<0.001) hemoglobin values in all patients. There was no statistically significant difference between 0-14 days (p=0.397) and 0-28 days(p=0.310) ferritin values in all patients. A statistically significant difference was found between 14-28 days(p<0.001) ferritin values. When the rate of change of hemoglobin and ferritin values between the groups was compared and no statistically significant difference was observed between the groups. The rate of change of ferritin values for 14-28 days was significant (p=0.012). There was no significant difference in the frequency of symptoms in the 14th day and 28th day controls for each group (p>0.05). The incidence of metallic taste and bloating symptoms was found to be statistically significant in the third control in the group with 2x1 drug use alternate day (p=0.094). Discussion: The only difference in efficacy was observed in ferritin values between 14th and 28th days. The increase in ferritin values was higher in the group that used 1x1 oral iron every day. However, since no difference was observed between the groups in terms of ferritin and hemoglobin values on days 0 and 28, all three groups were considered equally efficient. Side effects were mainly gastrointestinal side effects. Since the group that received 2x1 oral treatment alternate day had a statistically significantly higher rate of side effects, the patients’ treatment tolerance will be lower compared to the other groups. In conlusion, there is no difference in efficacy and side effects between the patient groups receiving 1x1 daily and 1x1 alternate day oral iron therapy, so 1x1 use alternate day is the most appropriate treatment method for oral iron therapy in terms of patient tolerance, adherence to treatment and pharmacoeconomics.

The necessity for precise and current data concerning the dynamics of land cover change in Indonesia is crucial for efforts to reduce natural vegetation cover due to agricultural expansion. The functionality of monitoring systems that incorporate Terra-MODIS is currently compromised by the limited availability of data for the immediate future. This study seeks to assess the potential of VIIRS satellite imagery in developing an early warning system for monitoring vegetation cover change in Indonesia. The Normalized Differential Open Area Index (NDOAI) computed from the 8-day’ VIIRS data was employed to detect changes in vegetation cover based on pixel-by-pixel subtraction in the NDOAI data time series. Evaluating the pixel-level accuracy of change detection is complicated due to the fact that we evaluate a change map at a coarser resolution than the Landsat-based reference map. The results revealed that increasing the threshold percentage is associated with improved accuracy. In change detection, there is often a trade-off between accuracy and sensitivity. A threshold that is too low may result in false positives, while a threshold that is too high may lead to missed changes. This study demonstrates that when a threshold value of less than 20% is applied, Landsat can identify vegetation cover changes at an earlier stage. Conversely, when a threshold value greater than 20% is employed, VIIRS will detect the change 4.5 days earlier than Landsat. Additionally, VIIRS is capable of detecting changes 25.4 days and 54.8 days faster than Landsat, respectively, when using thresholds of 40% and 75%.

Daily maximum surface air temperature (Tamax) is a crucial factor for understanding complex land surface processes under rapid climate change. Remote detection of Tamax has widely relied on the empirical relationship between air temperature and land surface temperature (LST), a product derived from remote sensing. However, little is known about how such a relationship is affected by the high heterogeneity in landscapes and dynamics in seasonality. This study aims to advance our understanding of the roles of land cover and seasonal variation in the estimation of Tamax using the MODIS (Moderate Resolution Imaging Spectroradiometer) LST product. We developed statistical models to link Tamax and LST in the middle and lower reaches of the Yangtze River in China for five major land-cover types (i.e., forest, shrub, water, impervious surface, cropland, and grassland) and two seasons (i.e., growing season and non-growing season). Results show that the performance of modeling the Tamax-LST relationship was highly dependent on land cover and seasonal variation. Estimating Tamax over grasslands and water bodies achieved superior performance; while uncertainties were high over forested lands that contained extensive heterogeneity in species types, plant structure, and topography. We further found that all the land-cover specific models developed for the plant non-growing season outperformed the corresponding models developed for the growing season. Discrepancies in model performance mainly occurred in the vegetated areas (forest, cropland, and shrub), suggesting an important role of plant phenology in defining the statistical relationship between Tamax and LST. For impervious surfaces, the challenge of capturing the high spatial heterogeneity in urban settings using the low-resolution MODIS data made Tamax estimation a difficult task, which was especially true in the growing season.

Cancer cells are believed to be recognized and controlled by the immune system of the host, especially the adaptive immune system. Cancers may be initiated by a single gene defect in stem cells or regenerating cells during the replacement of old or injured tissue cells, and additional gene defect(s) then occur. To compensate for missing proteins intracellular homeostasis systems, such as proteostasis, may work with activation of new genes. The risk or predisposing factors in cancers may be related to the number of tissue cell renewals (the turnover time) and the probability of gene defect(s). Oncological symptoms may be associated with substances that are derived from antigens expressed on cancer cells and those derived from damaged cancer cells with corresponding immune reactions. In patients with cancers or other conditions, inadequate immune components to control these substances may result in chronic inflammatory or autoimmune diseases. Cancer cells communicate with host cells, including the immune cells such as T cells, for survival and proliferation and may need assistance from immune cells against intracellular infections or physicochemical insults. T cell-based immune therapeutics have been developed and clinically used in some cancers, especially in advanced cancers. We further discuss the oncogenesis, pathophysiology of cancers, and unresolved issues in tumor immunology and reinterpret the effectiveness of T cell-based therapies under the protein-homeostasis-system hypothesis.

In case of the maximally rotating Black Holes (BH) through Kerr-Neumann frames, or as described in Boyer-Lindquist coordinates metrics, the rotation axis of the BHs inputs a frame dragging effect i.e., relativistically a Lens-Thirring Precession that accelerates the photon trajectories oscillates with a shaped induced rotations through the ring singularity, between alternate universes, as a means of an induced geodesics that takes a sharp turning points back and forth provided, in the prograde photon sphere, due to magnetorotational instability, the path tracing of a photons circulates as a smooth fiber bundles over the event horizon curves, that when gets interpolate between mixed trajectories behaves as a geodesics and thus forms a smooth Jacobi-fields through Jacobi-lines by mutual intersection of geodesics over the photon sphere which when somehow gets leaked inside the event horizon, then gets sucked in with not sufficient escape velocity for retardation and trapped in the compact singularity, oscillating back and forth through alternate universes.

A testable hypothesis with quantitative predictions is put forward, proposing that strong acids produced on land at a rate correlated with global population are an increas-ing cause of increasing atmospheric CO2 pressure (pCO2). This hypothesis widens the imbalance assumed between the global uptake of CO2 by photosynthesis and emissions of CO2 from all sources, including the combustion of fossil fuels, causing greater atmos-pheric pCO2. Our modelling tests for reactions of dissolved inorganic carbon show that increasing atmospheric CO2 is caused thermodynamically by falling land surface pH values, but only with bicarbonate present. Strong acids generated by oxygen from re-duced inorganic compounds of nitrogen and sulphur emit CO2 almost stoichiometrically from dissolved bicarbonate in the pH range of most global soils, between 6 to above 8. We show that each decrease of aqueous pH value of 0.01 units from acidification of sur-face water near pH 8 potentially increases the pCO2 in the atmosphere by about 7 ppmv. The surface pH value of the ocean near 8.10 in 2000 has been shown to decrease at this rate, a result of equilibrating with the rising atmospheric pCO2. Therefore, our qualita-tive estimates of increasing atmospheric CO2 driven by irreversible acidification on land are critical and need broad scale validation. Unfortunately, these acidifying processes on land from excessive nitrogen fertiliser, export of alkaline produce from farmlands and other processes were not considered by previous biogeochemical reviews. However, several very recent research studies showing CO2 emissions from soil during nitrifica-tion are consistent with our hypothesis. Despite counter measures to curb excessive CO2 emissions, including carbon capture and geological storage, the increasing Keeling curve for pCO2 may continue to rise because zero carbon policies do not address these causes. We recommend that this hypothesis be further tested by in situ experiments in neutral soils and water, designed to compare CO2 emissions under the acidifying conditions de-scribed in this article. Corrective counter measures can then be designed and applied.

The work aims to develop an electromagnetic shielding measurement methodology and design an electromagnetic shielding effectiveness test setup for thin sheet material testing. In brief, multiple shielding effectiveness standards are described and analyzed in the thin sheet material testing framework. Two types of the developed shielding effectiveness test probe in high and low-frequency ranges are validated comprehensively. Extensive descriptions and data of developed testing methodology are also reported.

Highly diverse agroecosystems are increasingly of interest as the realization of farms' invaluable ecosystem services grows. Simultaneously there has been an increased use of uncrewed aerial systems (UAS) in remote sensing as drones offer a finer spatial resolution and faster revisit rate than traditional satellites. With the combined utility of UAS and the attention on agroecosystems, there exists an opportunity to assess UAS practicality in highly biodiverse settings.  In this study, we utilized UAS to collect fine-resolution 10-band multispectral imagery of coffee agroecosystems in Puerto Rico. We created land cover maps through a pixel-based supervised classification of each farm and assembled accuracy assessments for each classification. To bolster our understanding of the classifications, we interviewed farmers to understand their thoughts on how these maps may be best used to support their land management. The average overall accuracy (53.9%), though relatively low, was expected for such a diverse landscape with fine-resolution data. After sharing imagery and land cover classifications with farmers, we found that while the prints were often a point of pride or curiosity for farmers, integrating the maps into farm management was perceived as impractical. These findings highlight that while remote sensing of diverse agroecosystems may provide a detailed way of estimating land cover classes and ecosystem services for researchers and government agencies for example these maps may be of limited use to land managers without additional interpretation.

The intelligent morphing wing structure has the characteristics of flexibility, large deformation and adaptive change, which are different from those of the conventional wing. The motion law of the variable-camber leading edge is analysed by the numerical simulation method based on kinematics theory to solve the problem of verifying the motion function and structural strength of the variable camber wing. The driving deformation and aerodynamic load simulation of the variable camber leading edge are realised by designing a follow-up load test apparatus. Based on the numerical simulation of the mechanical boundary, the motion trajectory of the upper and lower wing loading points was predicted, and a multi-point cooperative control system was developed. Multi-sensor iteration was used to ensure the loading accuracy of the test control. The test results show that the average error of the deflection angle is 4.59% in the variable camber leading edge motion test. In the variable camber leading edge strength test, the average error of applied load magnitude and direction is 0.54% and 0.24%, respectively.

The availability of current land cover and land use (LCLU) information for monitoring the status of land resources has considerable value in ensuring sustainable land use planning. Similarly, the need to provide updated information on the extent of LCLU change in West Africa has become apparent, given the increasing demand for land resources driven by the rapid population growth in the sub-region. SERVIR West Africa, a regional consortium jointly supported by USAID and NASA to foster the use of geospatial and earth observation data and science for decision-making on critical environmental and food security challenges, in collaboration with the Food and Agriculture Organization of the United Nations (FAO), is building technical capacity in the sub-region to develop and implement harmonized regional land cover classification system for LULC change monitoring in West Africa, based on the Land Cover Meta Language (LCML-ISO 19144-2). This article focuses on the process, potential opportunities, outputs of this collaboration, exemplary use cases, and recommendations for the next steps.

Successful geophysical exploration works in Gucheng-Yaxi area located in Gaochun District, Jiangsu province, China, have been limited partly due to complex geological condition of the area and high artificial noise in data acquired using electrical and electromagnetic methods. In this work, we deployed the new anti-interference spread spectrum induced polarization method (SSIP) and audio magnetotellurics (AMT) method to detect a copper-polymetallic deposit in the area. Two-dimensional (2D) inversion results at Gucheng-Yaxi Area revealed a high chargeability anomalous zone on SSIP profile that coincided with a zone of moderate resistivity located between two resistor bodies on AMT profile. A follow up 1200 meters drill hole was established at this high chargeability-moderate resistivity zone which encountered polymetallic (copper, lead, zinc, gold and silver) mineralization at the depth ≥ 400 m. Drill hole data analysis showed that mineralization occurs interspaced in marble rock mass at varies depth. Furthermore, several low resistivity-weak chargeability sections were revealed and inferred attributed to Cretaceous sediments and faults. These faults are thought to have played critical role in the polymetallic mineralization genesis. In summary, this work demonstrated the successful of application of SSIP and AMT at detecting a metallic deposit in an area with high artificial noise. Hence the geophysical prospection potential of Gucheng-Yaxi area is great.

The paper focuses on the admissibility problem of descriptor fractional-order systems (DFOSs). The alternate admissibility criteria are addressed for DFOSs with order in (0,2) which involve a non-strict linear matrix inequality (LMI) method and a strict LMI method, respectively. The forms of non-strict and strict LMIs are brand-new and distinguished with the existing literature, which fill the gaps of studies for admissibility. These approaches are available to the order in (0,2) without separating the order ranges into (0,1) and [1,2). In addition, a method involved least real decision variables in terms of strict LMIs is derived which is more convenient to process the practical solution. Three numerical examples are given to illustrate the validity of proposed results.

While there is overwhelming evidence for dark matter (DM) in galaxies and galaxy clusters, all searches for DM particles have so far proved negative. It is not even clear whether only one particle is involved or a combination or particles, their masses not precisely predicted. This non-detectability raises the possible relevance of modified gravity theories – MOND, MONG, etc. Here we consider a specific modification of Newtonian gravity (MONG) which involves gravitational self-energy, leading to modified equations whose solutions imply flat rotation curves and limitations of sizes of clusters. The results are consistent with current observations including that involving large spirals. This modification could also explain the current Hubble tension. We also consider effects of dark energy (DE) in terms of a cosmological constant.

A major problem of the technological production process of the metallurgical-grade silicon is formation of a large amount of microsilica. However, this material can be a significant source of raw materials for its own production. Hence, this study is aimed to solve the problem of micro-silica utilization, i.e. the technogenic dust-like waste generated during the melting of the technical-grade silicon. Within this study, the technology of the joint briquetting of microsilica was investigated with the carbonaceous reducing agents, i.e. by obtaining of mono-charge and by melting of the technical-grade silicon from the obtained mono-charge in the 200kVA ore-thermal furnace. Results of the study show that the briquettes in the melting process of the technical-grade silicon can be used in the range from 0 to 50%. The using of briquettes may significantly improve the technological parameters. When briquetted charge is applied only, the technological parameters will deteriorate significantly. The material balance of silicon melting showed the recovery rates of the main elements (Si, Al, Ca and Fe). It recorded a decrease in content of aluminum from 1.9-2.1% to 0.5-0.7%, calcium from 0.2-0.3% to 0.07-0.1% and titanium from 0.2-0.23% to 0.11-0.13% during the transition to briquetted monocharge. Phosphorus content increased from 0.004-0.005 to 0.011-0.013%.

This study investigates the effect of scaffold architecture on bone regeneration, focusing on 3D-printed polylactic acid-bioceramic calcium phosphate (PLA-bioCaP) composite scaffolds in rabbit femoral condyle critical defects. To assess their influence on bone healing and scaffold performance, we explored two distinct scaffold designs, alternate and helical laydown patterns. The scaffolds were meticulously characterized for pore size, strut thickness, porosity, pore accessibility, and mechanical properties. The in vivo efficacy of these scaffolds was evaluated using a rabbit femoral condyle critical defect model. Our findings indicate that both scaffold architectures are biocompatible and support bone formation. The helical scaffolds, characterized by larger pore sizes and higher porosity, demonstrated significantly greater bone regeneration than the alternate structures. However, their lower mechanical strength presented limitations for use in load-bearing sites. This study highlights the importance of scaffold architecture in bone tissue engineering and underscores the need to balance porosity and mechanical strength for optimal bone regeneration. The findings provide crucial insights for the design of 3D- printed scaffolds in clinical applications, particularly in the context of critical-sized bone defects. The study also outlines potential areas for future research, including exploring hybrid scaffold designs to achieve optimal porosity without compromising mechanical integrity.

The Kampar Peninsula, a significant peatland region in Riau, Indonesia, is vital for its carbon re-serves and biodiversity, including the Sumatran tiger. Covering approximately 735,091 hectares, it comprises critical peat domes essential for hydrological balance. This research investigates land use changes from 1990-2020 using the Normalized Difference Fraction Index (NDFI) to map disturb-ances and land cover changes. Additionally, interviews and regulatory analysis were conducted to examine the historical drivers of land use change in the Kampar Peninsula. In 2020, natural forests covered 433,395.20 hectares (59.9% of the total area), industrial pulpwood plantations (primarily acacia) covered 27.3%, oil palm plantations accounted for 10.4%, infrastructure occupied 2.4%, and water bodies made up 0.9%. Key drivers of land use change include the construction of access roads by oil companies since 1975 and government policies during the New Order period (1980s-1998) promoting forest exploitation and transmigration programs. These activities have significantly transformed the Kampar Peninsula's land cover, highlighting the need for sustainable management and conservation efforts.

Emphasizing the importance of acoustic attenuation in maintaining compliance with stringent noise regulations and enhancing workplace safety, the analysis covers the theoretical and practical aspects of sound attenuation in a turboengine testing stand. This paper presents a preliminary analysis and also an evaluation of a procedure for projecting a noise attenuator for industrial application and especially for turboengine test stands. While primarily focusing on the static acoustic behavior of the attenuator, considerations were also made regarding flow dynamics, Mach number-dependent attenuation, pressure drop, and self-generated noise aspects to provide a comprehensive perspective in selecting the optimal design configuration. The study investigates different calculation methods for assessment of the noise reduction for linear and staggered baffles, applied on a scaled reduced model of attenuator. Thus, the critical parameters and projecting requirements necessary for effective noise reduction in high-performance turboengine testing environments will be evaluated in a down-scaled model. Key factors examined include the selection of design parameters and configurations from various options. Advanced computational methods, like analytic and finite element analysis (FEM) are utilized to predict the acoustic performance and identify potential design optimizations. Experimental validation is performed to corroborate the simulation results, ensuring the reliability and efficiency of the attenuator. The findings indicate that a well-designed sound attenuator module can significantly reduce noise levels without compromising the operational performance of the turboengine inside a test cell.

The land use land cover (LULC) map is extensively employed for different purposes. The LULC maps provided by the Portuguese National Geographic Information System (SNIG) are not ideal for continuous assessment and regular scrutiny. Machine learning (ML) algorithms applied in remote sensing (RS) data has been proven effective in image classification, object detection, and semantic segmentation. Previous studies have shown that Random Forest (RF) and Support Vector Machine (SVM) consistently achieved high accuracy for land classification. In this study, the application of RF and SVM classifiers, and object-based (OBIA) and pixel-based (PBIA) approaches with Sentinel-2A imagery was evaluated using Google Earth Engine (GEE) platform for land cover classification of a burned area in the Serra da Estrela Natural Park (PNSE), Portugal. This aimed to detect the land cover change and closely observe the burned area and vegetation recovery after the 2022 wildfire. The combination of RF and OBIA achieved the highest accuracy in all evaluation metrics. At the same time, a comparison with the Normalized Difference Vegetation Index (NDVI) map and Conjunctural Land Occupation Map (COSc) of 2023 year indicated that the SVM and PBIA map resembled the maps better.

Tack is one of the most important factors affecting the operability of prepregs, but it is still very difficult to obtain the change of prepreg tack with time at different temperatures. In this paper, a newly designed T-peel device is used to test the tack decay rate of prepregs at different temperatures. The obtained decay rate deviates less than 8.9% from the manufacturer's data. The maximum deviation of the ratio of tack decay speeds calculated by the Arrhenius equation from the experiments is not higher than -9.7%. It is proved that the present method can obtain the decay rate of tack of prepregs at different temperatures. This method is also applicable to the other two types of prepregs. The article proposes the handling life unit, an operational life measurement unit for prepregs, and establishes that the relationship between tack and remaining shelf life reduces prepreg management costs.

Employing remote sensing techniques to evaluate crop residue cover (CRC) enables rapid mapping of tillage practices over large cropland areas, which has significant practical implications for monitoring the implementation of conservation tillage practices. This research utilized Sentinel-2 MSI and Landsat-8 OLI remotely sensed data, various spectral indices were calculated and the datasets were correlated with the field-measured CRC data. Selected spectral indices, highly significantly correlated, were chosen to build a correlation model between the indices and the CRC. Considering Sentinel-2 MSI and Landsat 8 OLI remotely sensed data variations in spectral and spatial scales, the accuracy of CRC models was evaluated using R2 and RMSE values. From the results, it's evident that all six spectral indices, including STI, NDTI, SRNDR, NDI5, NDI7 and NDSVI, registered correlation coefficients with the CRC exceeded 0.3 in the study area. STI and NDTI showed a stronger correlation to CRC, with coefficients of 0.810 and 0.803, respectively. For the Landsat 8 data, the lowest correlation obtained was for NDSVI with the Landsat 8 data with a correlation coefficient of 0.358. Applying the linear regression technique, STI and NDTI obtained higher accuracy compared to other indices in the Sentinel-2 MSI data. For NDTI and STI, The R2 values were 0.650 and 0.665, respectively, while their corresponding RMSE values were 3.96% and 4.03%. The highest model accuracy was obtained for the STI and NDTI constructed from the Landsat 8 OLI data (R2 values 0.41 and 0.40; RMSE values 5.25% and 5.27%, respectively). The CRC model built using partial least squares regression (PLSR) exhibited greater precision when applied to the Sentinel-2 MSI data (R2 value 0.894; RMSE value 2.18%) in comparison to the Landsat 8 OLI data (R2 value 0.695; RMSE value 3.70%). PLSR has the potential to enhance the precision of the model. In addition, the study area shows that the estimation of the CRC is better in the one-dimensional linear regression model and the PLSR model created with the Sentinel-2 MSI optical data compared to the Landsat 8 OLI optical remotely sensed data. The validation suggests that the CRC estimation in the study area is more precise when using the model relying on Sentinel-2 satellite imagery rather than the Landsat 8 OLI imagery.

In this data deposit, I describe a dataset that is the result of content mining 167,318 published articles for statistical test results. As a result of this content mining, 688,112 results from 50,845 articles were extracted. In order to provide a comprehensive set of data, the statistical results are supplemented with metadata from the article they originate from. The dataset is provided in a comma separated file (CSV) in long-format. For each of the 688,112 results, 20 variables are included, of which seven are article metadata and 13 pertain to the individual statistical results (e.g., reported and recalculated p-value). A five-pronged approach was taken to generate the dataset: (i) collect journal lists, (ii) spider journal pages for articles, (iii) download articles, (iv) add article metadata, and (v) mine articles for statistical results.

The demonstration of compliance of rolling stock against disturbance limits for railway signaling, and in particular track circuits, is subject to a large deal of variability, caused by the diverse values of the electrical parameters of the railway line and resulting transfer functions, as well as operating conditions of rolling stock during tests. Instrumental uncertainty is evaluated with a Type B approach and shown to be much less than the experimental variability. Repeated test runs in acceleration, coasting, cruising, braking conditions are considered, deriving both max-hold (spread) and sample dispersion curves compared to the respective mean values (Type A approach to the evaluation of uncertainty). The major source of variability affecting a significant portion of the spectrum is caused by the superposed oscillations of the onboard LC filter, for which different choices of the transformation window duration are discussed. The test runs and the acquired data covered overall 1 day of tests along about 300 km of the Italian 3 kV DC railway network.

The zinc oxide (ZnO) arrester is positioned on locomotive roof preventing other onboard electrical equipment from the harm caused by external and internal overvoltages. A number of locomotive arrester burnout and explosion accidents occur during traction supply network harmonic resonance causing train stoppages and power outages in the network. This study firstly carries out high-frequency tests to investigate the wide frequency band electrical characteristics of the locomotive arrester, explaining that the arrester is prone to fault during resonance. Consequently, a prognostics and health management (PHM) for locomotive arrester is proposed providing on online monitoring, fault warning and health assessment solutions, which is beneficial to the operation and maintenance of arresters in the future. The testing method and PHM scheme presented in this paper can be not only applied to the arrester, also readily expanded to other high-voltage electrical equipment on the electric locomotive.

Significant changes in Land Use and Land Cover (LULC) have widespread implications for the environment, economy, and society; influencing future sustainability and development of a region. This study aimed to assess LULC changes for a 30 year period (1990 – 2020) and project future LULC from 2030 to 2100 for the Irrawaddy Delta using remote sensing and simulations with the artificial neural networks-cellular automata method. The findings showed significant LULC changes in the Delta, particularly for the mangrove forests and cropland (rice paddies). Mangrove coverage was 1,471 km² in 1990 but decreased to 1,282 km² in 2020, and simulations predict a further reduction to 1,277 km² in 2100. Cropland areas increased from 10,550 km² to 10,618 km² in 2020, with simulations projecting a slight decrease to 10,586 km² by 2100. Human activities and cyclonic events, especially in the southern part of the region, have led to barren land and impervious areas replacing dense mangrove and forested areas. These changes threaten the ecological integrity of the Delta and impact local livelihoods and biodiversity. The study underscores the need for sustainable land management practices and policies to mitigate the adverse effects of LULC changes and ensure the resilience of the Irrawaddy Delta against ongoing environmental challenges.

Conditional Independence (CI) testing is fundamental in statistical analysis. For example, CI testing helps validate causal graphs or longitudinal data analysis with repeated measures in causal inference. CI testing is difficult, especially when testing involves categorical variables conditioned on a mixture of continuous and categorical variables. Current parametric and non-parametric testing methods designed for continuous variables and can quickly fall short in the categorical case. This paper presents a computational approach for CI testing for categorical data types, which we call computational conditional independence (CCI) testing. The test procedure is based on permutation and combines machine learning prediction algorithms and Monte Carlo Cross-Validation. We evaluated the approach through simulation studies and assessed the performance against alternative methods; the generalized covariance measure (GCM) test, the kernel conditional independence (KCI) test, and testing with multinomial regression. We find that the computational approach to testing has utility over the alternative methods, and we can achieve better control over type-I-error rates. We hope this work can expand the toolkit for CI testing for practitioners and researchers.

This study extends the CGAN-based MODIS cloud vertical-profile (64×64-scene, about 70km width×15km height) retrieval technique developed by Leinonen et al. (2019) [1] to construct seamless 3D cloud fields for the MODIS granules [2]. Firstly, the accuracy and spatial continuity of the Leinonen et al. [1] retrievals are statistically evaluated. Then, according to the characteristics of the retrieval error, a spatially overlapping-scene ensemble generation method and a bi-directional Ensemble Binning Probability Fusion (CGAN-BEBPF) technique are developed, which improves the CGAN retrieval accuracy and support to construct seamless 3D clouds. The CGAN-BEBPF technique involves three steps: cloud masking, intensity scaling, and optimal value selection. It ensures adequate coverage of the low reflectivity areas while preserving the high reflectivity cloud cores. The technique is applied to retrieve the 3D cloud fields of Typhoon Chaba and a multi-cell convective system. The cloud structures of the CGAN-BEBPF results are highly consistent with the ground-based radar observations. It can retrieve weak clouds at the top levels of convective storms and hurricanes that were missed by ground-based radars and fill the gaps of the ground-based radar lower-level PPI scan. Overall, CGAN-BEBPF can be automated to retrieve the rich informative 3D structures of typhoons and severe convective systems over the oceans along the MODIS swath, which certainly presents great value for improving maritime and near-shore typhoons and convection prediction and other cloud-sensitive applications.

Addressing the significant challenge in high-speed cotton dibbling operations in Xinjiang—specifically, the duck bill’s ("Duck bill" is a type of duck-billed bunch planting mechanism or component). shortened opening duration leading to seed throwing and floating—a new crawler-type delayed hole-forming mechanism has been designed. This mechanism extends the duck bill horizontally, thereby prolonging its opening time, enabling cotton sowing speeds of up to 6 km/h. Following agronomic principles for cotton planting, the overall layout of the crawler-type hole-forming mechanism, the structural parameters of the key components and the trajectory of the hole-forming are determined. We use the Discrete Element Method (DEM) and multi-body dynamics coupling method to simulate and analyze the motion process of the device. The fixed the tilt angle of the duck bill α(A), the depth of the duck bill hole-forming into the soil h(B), and the angle of rotation of the moving duck bill β(C) were taken as the experimental factors, with the longitudinal length of cotton seed hole (Y1) and the hole-forming depth of cotton seed hole (Y2) as the response values. The parameter range of each factor and the preliminary influence on the response value were determined through pre-experiments and single-factor simulation test. Based on RecurDyn-EDEM coupling, a quadratic regression orthogonal rotation combination simulation test was carried out. The results show that the order of the primary and secondary factors affecting the Y1 of the time-lapse hole-forming device was: A > C > B. The order of primary and secondary factors affecting the Y2 of the delayed hole forming device was: B > C > A. When the A was 2.4 °, the B was 42.4 mm, and the C was 30.5 °, the performance of the hole-forming was the best, and the Y1 was 26.4 mm, and the Y2 was 25.0 mm. The bench verification test results show that under the optimized combination of operating parameters, the average Y1 was 29.1 mm, and the average Y2 was 23.2 mm. Compared with the results of the previous coupled simulation model, the average relative errors of the two are 7.23 % and 4.36 %, respectively, indicating the accuracy and effectiveness of the established DEM simulation model and virtual test analysis. The hole-forming area and the opening time of the duck bill after the stable operation of the machine were recorded and measured. The calculated hole dislocation rate Hc was 4.33 %, which did not exceed the national standard requirement of 6 %. The qualified rate of hole distance Hx was 94.33 %, which was much higher than the national standard requirement of 80 %. The average opening time of the duck bill at a speed of 6 km/h is 0.45 s, which is much longer than the time required for cotton seeds to fall from the duck bill 0.11 s. It meets the requirements of high-speed cotton planting in China and facilitating advancements in future high-speed planter technology.

Background: The skin prick test (SPT) is used to diagnose sensitization to antigens. This study proposes a deep learning approach to infer wheal dimensions, aiming to reduce dependence on human interpretation. Methods: A dataset of SPT images (n=5844) was used to infer a convolutional neural network for wheal segmentation (ML model). Three methods for inferring wheal dimensions were evaluated: the ML model; the standard protocol (MA1); and approximation of the area as an ellipse using diameters measured by an allergist (MA2). The results were compared with assisted image segmentation (AIS), the most accurate method. Bland-Altman, distribution analyses, and correlation tests were applied to compare the methods. The study also compared the percentage deviation among these methods in determining the area of wheals with regular geometric shapes (n = 150) and with irregular shapes (n=150). Results: The Bland-Altman analysis showed that the difference between methods was not correlated with the absolute area. The ML model achieved a segmentation accuracy of 85.88% and a strong correlation with the AIS method (ρ=0.88), outperforming all other methods. Additionally, MA1 showed significant error (13.44±13.95%) for pseudopods. Conclusions: The ML protocol can potentially automate the reading of SPT, offering greater accuracy than the standard protocol.

The aim of this work is to introduce a mathematical model representing the evolution of the temperature in a vegetation cover and the ground underneath it. Vegetation, and its interaction with soil, plays a very important role in the protection of soil surface from the action of sun and precipitations. A reduction in the vegetated mass increase the risk of desertification, soil erosion or surface runoffs which which can give rise to soil loss and sediment retention. These processes can favour climate change and global warming, which are major concerns nowadays. The mathematical model presented takes into account the main processes involved in vegetation cover and the interaction with the soil, among which, we can mention the Leaf Area Index, which is a dimensionless quantity defined as the one-sided green leaf area per unit ground surface area, or albedo and co-albedo which are clearly influenced by the vegetation. It is also considered a nonlinear heat capacity in the soil which incorporates the latent heat of fusion, when the phase change takes place. The numerical technique used to solve the mathematical model is based on a finite volume scheme with Weighted Essentially Non Oscillatory technique for spatial reconstruction and the third order Runge-Kutta Total Variation Diminishing numerical scheme is used for time integration. Some numerical examples are solved to obtain the distribution of temperature both in the vegetation cover and the soil.

We evaluated the potential of using fish species and functional traits as indicators of land use impacts to fish assemblages. We used environmental data collected at multiple spatial scales (local, reach, and upstream catchment) for 19 tributary and main stem sites in the Nolichucky River watershed in Tennessee. Canonical correspondence analyses showed that temperature, elevation, specific conductivity, sediment yield, impervious surfaces, and row crop cover at the catchment scale were strongly associated with fish assemblage structure, as well as forest cover from all three spatial scales. Blocked indicator species analysis, with stream size as the block, showed that significantly strong indicators of the least-impacted riparian land use condition (≥60% forest cover) were Saffron Shiner (Notropis rubricroceus), Rainbow Trout (Oncorhyncus mykiss), Longnose Dace (Rhynichthys cataractae), Creek Chub (Semotilus atromaculatus), and Mottled Sculpin (Cottus bairdi). Traits indicative of the least-impacted sites were the herbivorous trophic guild, mean female age-at-maturity, longevity, rock-gravel spawners, montane geology and pelagic swimmers. Specific conductivity was strongly related to multiple catchment-scale land use variables, and was a strong local-scale influence on fish assemblage structure. Our results show promise for using a relatively common but endemic southern Appalachian fish species, the Saffron Shiner, as an indicator for land-use related impacts to these streams.

Rice provides ~20% of human dietary energy and, for many people, a similar share of their protein. Rice cultivation, however, produces significant greenhouse gas (GHG) emissions, comparable to those from the aviation sector. The main GHG from rice production is methane, mostly a result of conventional rice cultivation (CRC) keeping rice fields continuously flooded during the crop cycle. There is extensive evidence that alternate wetting and drying (AWD) of rice fields substantially reduces methane emissions. AWD is one component of the System of Rice Intensification (SRI), an agroecological approach to the management of plants, water, soil and nutrients practiced by millions of farmers in both lowland irrigated rice and upland rainfed cultivation. Thirteen countries have included SRI in their Nationally Determined Contributions to GHG reduction or climate change mitigation. This article reviews 16 field studies of the net reduction in GHG emissions from the adoption of AWD, eight from the adoption of SRI, and two that compared SRI and AWD. Where available, the review includes data on yield and therefore on carbon dioxide-equivalent GHG emissions per kilogram of rice produced. The evidence indicates that AWD and SRI offer a similar and substantial reduction (~35–41%) in GHG emissions per hectare compared with conventional rice cultivation. However, SRI offers ~66% greater yield than CRC, and therefore greater reduction in emissions per kilogram of rice, ~54% more than AWD. The limited data directly comparing SRI and AWD support this finding. SRI also appears to have greater potential to sequester carbon in the soil. SRI lowers rice farmers’ costs of production, adds to their income and can make climate-friendly methods more attractive. Both AWD and SRI are greatly preferable to current conventional practices, but SRI offers opportunities to contribute to food security while directly addressing the drivers of climate change.

Laser Photoacoustic Spectrometers (LPAS), which provide photoacoustic spectra for detecting food frauds or adulteration, and fluorescence-based systems for recognition of contamination by heavy metal ions in water are two important families of sensors for health and environmental purposes. Both sensor families require one or more low-frequency Lock-In Amplifiers (LIAs) to extract the signal of interest from background noise. In the cited applications, the required LIA frequency is quite low (up to 1kHz), and this leads to a simplification of the hardware with consequent good results in portability, economy, reduced size, weight and low-cost characteristics. The present system, called ENEA DSP Box Due, is based on a very inexpensive microcontroller proto-board and can replace four commercial LIAs, resulting in significant savings in both cost and space. Furthermore, it incorporates a dual-channel oscilloscope and a sinusoidal function generator. This article outlines the architecture of the ENEA DSP Box Due, its electrical characterization and its applications within a project concerning laser techniques for food and water safety.

Recent advancements in deep learning have spurred the development of numerous novel semantic segmentation models for land cover mapping, showcasing exceptional performance in delineating precise boundaries and producing highly accurate land cover maps. However, to date, no systematic literature review has comprehensively examined semantic segmentation models in the context of land cover mapping. This paper addresses this gap by synthesizing recent advancements in semantic segmentation models for land cover mapping from 2017 to 2023, drawing insights on trends, data sources, model structures, and performance metrics based on a review of 106 extracted articles. Our analysis identifies top journals in the field, including MDPI Remote Sensing, IEEE Journal of Selected Topics in Earth Science, and IEEE Transactions on Geoscience and Remote Sensing, IEEE Geoscience and Remote Sensing Letters, ISPRS Journal Of Photogrammetry And Remote Sensing as the leading journals. We find that research predominantly focuses on land cover, urban areas, precision agriculture, environment, coastal areas, and forests. Geographically, 35.29% of the study areas are located in China, followed by USA (11.76%), France (5.88 %), Spain (4%) and others. Sentinel-2, Sentinel-1, and Landsat satellites emerge as the most commonly used data sources. Benchmark datasets such as ISPRS Vaihingen &amp; Potsdam, LandCover.ai, DeepGlobe, and GID datasets are frequently employed. Model architectures predominantly utilize encoder-decoder, and hybrid convolutional neural network-based structures because of their impressive performances, with limited adoption of transformer-based architectures due to its computational complexity issue, and slow convergence speed. Lastly, this paper highlights existing key research gaps in the field to guide future research directions.

Cardiac autonomic neuropathy (CAN) is a severe complication of diabetes mellitus (DM) strongly linked to a nearly five-fold higher risk of cardiovascular mortality. Patients with Type 2 Diabetes Mellitus (T2DM) are a significant cohort in which these assessments have particular relevance to the increased cardiovascular risk inherent in the condition. This study aimed to explore the subtle correlation between the Ewing test, Sudoscan-cardiovascular autonomic neuropathy score, and cardiovascular risk calculated using SCORE 2 Diabetes in individuals with T2DM. The cohort consisted of 211 patients diagnosed with T2DM with overweight or obesity without established ASCVD, aged between 40 to 69 years. The prevalence of CAN in our group was 67.2%. In the study group, according SCORE2-Diabetes, four patients (1.9%) were classified with moderate cardiovascular risk, thirty-five (16.6%) with high risk, and one hundred seventy-two (81.5%) with very high cardiovascular risk. On multiple linear regression, the SCORE2-Diabetes algorithm remained significantly associated with Sudoscan CAN-score and Sudoscan Nephro-score and Ewing test score. Testing for the diagnosis of CAN in very high-risk patients should be performed because approximately 70% of them associate CAN. Increased cardiovascular risk is associated with sudomotor damage and that Sudoscan is an effective and non-invasive measure of identifying such risk.

Snow cover plays a critical role in the global energy and water cycles. Snow cover on the Tibetan Plateau (TP) provides vital water sources in western China and Himalayan regions in addition to its weather and climate significance. The massive high mountain topography of the TP is main conditions for the presence and persistence of snow cover on the plateau at the mid-low latitudes of the Northern Hemisphere (NH). However, how mountain topography controls snow cover distribution on the TP is largely remain unclear and the relationship is not well quantified. Here, the spatial distribution of snow cover and topographic controls on snow cover on the TP are examined based on snow cover frequency (SCF) derived from MODIS snow cover product (MOD10A2 v5) and digital elevation model (DEM). The results show that snow cover on the TP is spatially unevenly distributed and is characterized by rich snow and high SCF on the interior and surrounding high mountain ranges, and less snow and low SCF in inland basins and river valleys. Snow cover on the TP presents elevation dependence with the higher the altitude, the higher the SCF, the longer the snow cover duration and the more stable the intra-annual variation. Annual mean SCF below 3000 m above sea level (masl) is less than 4% and it reaches 77% above 6000 masl. The intra-annual snow cover variation below 4000 masl features a unimodal distribution, while above 4000 masl it presents a bimodal distribution. The mean minimum SCF below 6000 masl occurs in summer, while above 6000 masl it occurs in winter. Because of differences in solar radiation and water vapor sources, mean SCF generally increases with mountain slopes and it is the highest on the north-facing aspect, whereas the lowest is observed on the south-facing aspect.

A land cover map of two arctic catchments, nearby the Abisko Scientific Research Station, was obtained from a classification of a Sentinel-2 satellite image and a ground survey performed in July 2022. The two contiguous catchments, Miellajokka and Stordalen, are covered by various ecotypes, from boreal forest to alpine tundra and peatland. The Random Forest algorithm correctly identified 83% of polygon pixels reserved for testing. The developed workflow relied solely on open source software and acquired ground observations. Space organization was directed by the altitude as shown by the intersection of the land cover with the topography. Comparison between this new land cover map and previous ones based on data acquired between 2008 and 2011 demonstrates some trends of vegetation cover evolution in response to climate change in the considered area. The potential applications in terms of permafrost modeling (hiperborea.omp.eu) are finally discussed.

Tamil Nadu, a state in southern India, is bereft of any native milch or dual-purpose cattle breed and the state depends chiefly on crossbred cattle for milk production. As most (90 percent) of the milk production in the state was contributed by Jersey crossbred cattle, the genetic evaluation study was intended to assess the milk production traits viz., test-day milk yields (TDMYs), total milk yield (TMY) and 305-day milk yield (305MY) in these crossbred cattle reared under farmers’ rearing environment. Data on monthly TDMYs (TDMY1 to TDMY10) of Jersey crossbred cows (n=81,653) reared by the farmers over 24 years (1999-2022) were collected for evaluation. The influence of non-genetic factors viz., location (agroclimatic zones), period and season of calving, and parity on TDMYs, TMY, and 305MY were assessed, and the variance and covariance components for genetic parameters (heritability and genetic correlation) of the traits were estimated by the method of restricted maximum likelihood (REML) under multivariate animal model and by random regression model (RRM). The overall means of various TDMYs ranged from 4.98 (TDMY10) to 9.95 kg (TDMY2) and, for TMY and 305MY the means were 2480.33 and 2393.71 kg respectively. The heritabilities estimated by animal model for TDMYs were high and ranged from 0.39 ± 0.01 to 0.47 ± 0.01 and were fairly less variable throughout the lactation while the estimates obtained by RRM were medium to high and ranged between 0.28 ± 0.01 and 0.65 ± 0.02 for different days in milk (DIMs). The heritability estimated for TMY and 305MY were 0.48 ± 0.01 and 0.49 ± 0.01 respectively. The estimates of heritability in mid-lactation yields were comparatively little less than those at the beginning and the end of lactation. The high estimates of heritabilities for TDMYs, TMY, and 305MY obtained in the present study offered an ample scope for improving milk production through selective breeding. Genetic correlations between TDMYs estimated by animal model were positive and moderate to high, with a range between 0.47 ± 0.01 and 0.99 ± 0.00. Considerably higher estimates (0.97-0.99) were observed between adjacent TDMYs showing strong genetic associations. By RRM, genetic correlations estimated between DIMs were positive, except for a few estimates and the magnitude of genetic correlation decreased with an increase in the interval between the DIMs. The high genetic correlation observed between the TDMYs in early and mid stages of lactation with TMY and 305MY suggested that these test day yields could be used favorably for the early selection of cows for milk production which facilitates reduction in the generation interval and consequently increase the annual genetic gain for the milk production traits.

In dry season paddy farming, the alternate wetting and drying (AWD) irrigation improves water productivity, paddy production, and has the potential to decrease greenhouse gas (GHG) such as methane (CH4) and nitrous oxide (N2O) emissions when compared to continuous flooding (CF). However, there is a lack of research in Bangladesh on the effects of water management on CH4 and N2O emissions. During November 2017–April 2018, participatory on-farm trials were conducted at Feni and Chattogram districts of Bangladesh. Total 105 farmers comprising 20-hectare of land (62 farmers at Feni and 43 farmers at Chattogram district, each location having 10 hectare of land). We compared irrigation water and cost reductions, paddy yield, and CH4 and N2O emissions from paddy fields irrigated using AWD and CF irrigation methods. The CH4 and N2O emissions were determined using the Cool Farm Beta-3 methodology, and the global warming potential (GWP) was estimated using the Intergovernmental Panel on Climate Change-2014 standard approach. The mean results of randomly selected 30 farmers from two locations (15 of each) showed that AWD remarkably decreased irrigation water consumption by about 24% and increased water productivity by 224%. We estimated 23% savings for irrigation costs in AWD. By this time, AWD improved paddy production by 3% over CF. The AWD irrigation resulted in a 47% reduction in cumulative CH4 emissions having a lower CH4 emission factor (0.74 kg ha-1 day-1) than CF (1.39 kg ha-1 day-1). There was no obvious difference in N2O emission between AWD and CF. When compared to CF, AWD decreased the overall GWP by 27% and lowered the GHG intensity by 42%. The CH4 and N2O emissions did not differ substantially between Feni and Chattogram.

As time continues to advance, the need for robust security threat mitigation has become increasingly vital in software. However, ensuring early effective security threat mitigation requires optimal test data and consistent test case design. It is a constant struggle to maximize test coverage through test data optimization. We conducted explanatory research to maximize test coverage of security requirements as modeled in Structured Misuse Case Description (SMCD) i.e., structured specification of misuse case, so as to improve consistency in optimal test data generation. We specified constraints upon Mal activity in Object Constraint Language (OCL) in order to minimize human dependency and improve consistency in optimal test data generation. It was evident through results that MC/DC generated optimal test data of security threats through SMCD in comparison to the Decision Coverage method thus resulting in designing a significantly lower number of test cases and yet maximizing test coverage of security threats. MC/DC generated test data with n+1, while Decision Coverage generated test data with〖 2〗^n, we, therefore, conclude that MC/DC maximizes test coverage through optimal test data from SMCD in comparison to Decision Coverage.

Then the purposes of this study were to compare and correlate the aerobic threshold (TH_aer) and anaerobic threshold (TH_anaer) measured during a new single judo specific incremental test and Treadmill Test for aerobic demand evaluation. Eight well-trained male competitive judo players (24.3±7.9 years; height of 169.3±6.7cm; fat mass of 12.7±3.9%) performed a maximal incremental specific test for judo mimicking the UchiKomi drills and on treadmill in different days. There was difference between specific and general TH_aer (P=0.0006) as well as weak correlation for TH_aer (r=0.32; R²=0.1; P=0.2) and TH_anaer (rs=-0.31; R²=0.1; P=0.12). When correlation was applied with normalized data (percentage of peak load) we observed moderate correlation for TH_aer (r=0.76; R²=0.58; P=0.027), but the same was not observed for TH_anaer. We conclude that there is a need of TH_aer and TH_anaer evaluation through a specific test for Judo.

The interface of a structural system in the soil is usually unsaturated. A decrease in the shear strength of the soil-structure interface can degrade the structure, especially under humid conditions. Studying the shear characteristics of the silt-concrete interface using a shear apparatus. Suction-controlled ring shear tests were carried out on the silt-concrete interface for three interface roughness values. The influence of the matric suction (s) and interface roughness (R) on the shear strength index of the silt-concrete interface was analyzed. The test results showed that high values of s and R improved the shear strength of the interface, but the result was affected by the net normal stress (NNS). High values of NNS and R improved the strain-hardening characteristics. NNS, s, and R significantly affected the interface shear shrinkage. The internal friction angle of the saturated interface was smaller than that of saturated silt, whereas the opposite occurred in the unsaturated state. The cohesion and internal friction angle of the interface rose with an increase in R, and they were larger than that of silt. A shear strength model of the silt and interface was established.

Sustainable continuous cover forestry is defined and analyzed in several ways. The differential equation representing growth of the basal areas of individual trees, motivated by fundamental biological production theory by Lohmander (2017a), is analyzed and extended in different directions. From the solution of the differential equation, the basal area and the tree diameter are obtained as explicit functions of time. The diameter is a strictly increasing function of time. In the absence of competitors, the diameter increment is shown to be a strictly decreasing function of time. Hence, the diameter increment can also be interpreted as a strictly decreasing function of the diameter. Alternative forms of adjustment of the differential equation, with consideration of competition, are defined. If the competition is strong, with large trees in the vicinity of a particular tree, then the basal area increment, and the diameter increment, are reduced. The growth of a large tree is less sensitive than the growth of a small tree, to competition from other trees. Under strong competition, the basal area increment, and the diameter increment, are strictly concave functions of the size of the tree. The unique maximum of the diameter increment occurs at a higher diameter, if the competition increases. In dynamic equilibrium, the tree size frequency distribution is stationary. If natural tree mortality can be avoided via the harvest strategy, the tree size frequency distribution is a function of the size and competition dependent growth function, and the harvest strategy. Empirical tree size frequency data are used to simultaneously estimate parameters of a size and competition dependent growth function and the applied harvest strategy, via nonlinear optimization. The properties of the estimated growth function are consistent with the corresponding properties of the production theoretically motivated hypothetical function, and the properties of the estimated harvest strategy confirm the corresponding hypotheses. The R2 of the nonlinear regression exceeds 0.97. With access to an empirically estimated equilibrium tree size distribution, it is possible to: 1. Estimate size frequency relevant parameters of tree size and competition dependent growth functions for individual trees. 2. Estimate the applied harvest strategy. 3. Explain and reproduce the empirically estimated tree size equilibrium distribution.

Genetic Programming (GP) is a powerful Machine Learning (ML) algorithm that can produce readable white-box models. Although successfully used for solving an array of problems in different scientific areas, GP is still not well known in Remote Sensing. The M3GP algorithm, a variant of the standard GP algorithm, performs Feature Construction by evolving hyper-features from the original ones. In this work, we use the M3GP algorithm on several sets of satellite images over different countries to create hyper-feature from satellite bands to improve the classification of land cover types. We add the evolved hyper-features to the reference datasets and observe a significant improvement of the performance of three state-of-the-art ML algorithms (Decision Trees, Random Forests and XGBoost) on multiclass classifications and no significant effect on the binary classifications. We show that adding the M3GP hyper-features to the reference datasets brings better results than adding the well-known spectral indices NDVI, NDWI and NBR. We also compare the performance of the M3GP hyper-features in the binary classification problems with those created by other Feature Construction methods like FFX and EFS.

State-of-the-art augmented-reality (AR) glasses record their position and orientation in space, enabling measurements and analyses of clinical gait-and-balance tests. This study’s objective was to evaluate concurrent validity and test-retest reliability for common clinical gait-and-balance tests in people with Parkinson’s disease: the Five Times Sit-To-Stand (FTSTS) and Timed Up-and-Go (TUG) tests. Position and orientation data was collected in 22 participants with Parkinson's disease using HoloLens 2 and Magic Leap 2 AR glasses, from which test-completion durations and durations of distinct sub-parts (e.g., sit-to-stand, turning) were derived and compared to reference systems and over test repetitions. Regarding concurrent validity, for both tests an excellent between-systems agreement was found for position and orientation time series and test-completion durations. Between-systems agreement for FTSTS (sub-)durations were all excellent, while TUG turning sub-durations were excellent (turn 1) and moderate (turn 2). Regarding test-retest reliability, the within-system test-retest variation in test-completion times and sub-durations was always much greater than the between-systems variation, implying that these (sub-)durations may be derived interchangeably from AR and reference-system data. In conclusion, AR data are of sufficient quality to evaluate gait and balance in people with Parkinson's disease, with valid quantification of test-completion durations and sub-durations of distinct FTSTS and TUG sub-parts.

Geopolymers, made from aluminosilicate raw materials, offer significant environmental advantages over conventional concrete (CC) mixes. This study explores the compressive strength, setting time, and durability of geopolymer concrete (GPC) cylinders, some of which include an additional ordinary portland cement (OPC) mix. Consistent material composition and testing methods are emphasized to achieve reliable results. MATLAB was utilized to develop and assess a neural network model predicting the compressive strength of GPC based on key variables. The model was validated using 16 experimental samples and 1047 samples from various studies. The performance plot displayed the Mean Squared Error (MSE) over iterations, identifying the best training performance at epoch 658 with an MSE of 5.3408. The Error Histogram highlighted distribution errors between predicted and actual compressive strength values, with the highest range from -1.015 to 0.3587, meaning that the predicted values were mostly within a small margin of error from the actual values. This narrow error range indicates that the ANN model has high accuracy in its predictions, as most errors are small and clustered around zero, demonstrating reliable performance in estimating compressive strength. Regression analysis showed varying correlation coefficients (training set R=0.98373, test set R=0.88164, and whole set R=0.96982), indicating adequate predictive accuracy. The results demonstrate that properly trained neural networks can effectively predict the compressive strength of GPC, highlighting its potential as a sustainable construction material.

This study uses a mass-spring-damping system to simulate the repeated strain of liquefaction cyclic triaxial tests. The two results are compared in this paper to understand the feasibility of the mass-spring-damping system developed in this paper and the feasibility of future research on this related topic and development potential. The main factors affecting this mode's repeated strain are the spring coefficient k and the external force Q0. The spring coefficient has an inverse relationship but does not increase in multiples. The external force has a direct proportional relationship but does not increase the result- a non-multiple increase. When the pore water pressure of the liquefied cyclic triaxial test specimen rises, it will cause the specimen to liquefy, decreasing effective stress, shear modulus G, and damping ratio D, causing an increase in strain. The shear modulus and damping ratio are related to the spring coefficients k and c. Both are variables that change with time. This article takes an original thin-tube specimen at point A in the Yunlin area in Taiwan as a testing example. Through Mathematica software, it can be obtained that the mass m=1kg, the spring coefficient k=244e-0.1t kgf/cm, and the damping coefficient c=0.739e-0.257t kgf-s/cm and external force Q0=10.1sin2πt kg; Finally, this study selected the original thin-tube specimens from four locations in the Yunlin area, and simulated the repeated strain amount of the cyclic triaxial test specimens through a spring-damping system. The results show that the spring-damping system is feasible for simulated cyclic triaxial tests because the model is simple and the parameters are easy to understand and obtain, which also shows the extensibility of this model. Preliminary results of the research show that this model can further simulate the repeated strain obtained by cyclic triaxial tests without considering the increased trend in pore water pressure and the decrease in effective stress during cyclic loading.

The textile sector is responsible for a number of environmental impacts. Due to the in-creasing quantities of textiles, their share is rising and a trend reversal from a linear to a circular textile chain is needed. This article presents the background, methodological approach and results of a participatory textile development model. In the commercial B2B sector, three textile prototypes were developed together with users and trialled over several months in three application areas. Textile development took into account the requirements of fibre regeneration in the product design and focused on innova-tive chemical recycling solutions. The three sustainably aligned textiles were subject-ed to spectroscopic and textile-technological tests. Screening life cycle assessments an-alysed their environmental profile and compared it with reference textiles that are used as standard. Overall, it is clear that the three textiles can match conventional ref-erence textiles in terms of quality and have considerable environmental benefits com-pared to the reference textiles. The user survey did identify concerns about a high arti-ficial fibre content, although a general rejection of recycled fibres was not observed. The results show that a transformation is possible, but must start with the fibre com-position; recycling, on the other hand, is of minor importance.

Empirical models help us understand the process of plant residue decomposition and nutrient release into the soil. The objective of this study was to determine an appropriate model to describe the decomposition of hairy vetch (Vicia villosa Roth) and cereal rye (Secale cereale L.) cover crop (CC) residue and nitrogen (N) release. Data pertaining to above and belowground CC residue mass loss and N release for up to 2633 cumulative decomposition degree days (112 d) after litterbag installation were obtained from two cropping system experiments, one conducted in 2015 and the other in 2017 and 2018 at the humid subtropical environment of southern IL, USA. Six exponential and two hyperbolic models were fit to percent mass and N remaining data to find the one with minimum Akaike Information Criterion (AIC) and residual sum of squares. Modified three-parameter single exponential and two- or three-parameter hyperbolic models best met the assumed criteria of selection for above and belowground CC residue, respectively. Fitting a double exponential model to a combined data for percent mass and N remaining, which identified two mass and N pools, a fast and a slow pool with different rate constants. A five-parameter double exponential with an asymptote met the preset criteria and passed all tests for normally distributed population, constant variance, and independence of residuals at α = 0.05 when fit to combined data of hairy vetch shoot mass and N remaining. However, a two-parameter hyperbolic and three-parameter asymptotic hyperbolic model provided the best fit to a combined data of cereal rye shoot mass and N remaining, respectively. Both hyperbolic decay models showed a good fit for belowground mass decomposition and N release for both CCs. Cereal rye had poorer fit than hairy vetch for mass and N remaining of both above and belowground mass. The best-selected decay models can be used to estimate the decomposition and N release rates of hairy vetch and cereal rye above and belowground residue in a similar environment.

Introduction: Biliary Atresia (BA) is a common cause of neonatal cholestatic jaundice which, if recognized and treated early, can be life-saving for the infant. If the liver biopsy suggests the presence of BA, exploratory laparotomy is then carried out to confirm the diagnosis, along with the Kasai procedure to provide drainage to the bile secreted by the liver. The purpose of this study is to get a deep dive into all the various imaging modalities that can diagnose BA more effectively and with absolute certitude, thus helping prevent several children from a grave prognosis.Methodology: For the collection of the data, a search was done by two individuals using PubMed, Google Scholar, and Cochrane Library databases for all relevant literature. Each qualifying paper was evaluated independently by two reviewers. Each article was analyzed for the number of patients, their age, procedure modality, complexity of ethology, and incidence of the pre-decided complications. The statistical software packages RevMan (Review Manager, version 5.3), SPSS (Statistical Package for the Social Sciences, version 20), Google Sheets, and Excel in Stata 14 were used to perform the statistical analyses. The data was obtained and entered into analytic software.Results: A total of 39 studies with 3,679 subjects were selected for the study, out of which 7 studies showed sensitivity above or equal to 95%, and an astounding 14 studies showed specificity above 95%. The value of True Positive (TP) was 1280, that of True Negative (TN) was 1817, that of False Positive (FP) was 239, and that of False Negative (FN) was 343. With a confidence interval of 95%, sensitivity, specificity, and positive predictive values were calculated. The sensitivity of Ultrasonography for Biliary Atresia is 0.79, with a CI of 95% in a range of 0.77 to 0.81. The specificity of Ultrasonography for Biliary Atresia is 0.88, with a CI of 95% in a range of 0.87 to 0.90. Conclusion: Even though several radiological techniques at present help to detect BA, USG of the abdomen proves to be an effective diagnostic and a modest screening test for the detection of BA.

Asymptotic theories for fractional cointegrations have been extensively studied in the context of time series data, with numerous empirical studies and tests developed. However, most of the previously developed testing procedures for fractional cointegration were primarily designed for time series data. This paper proposes a generalized residual-based test for fractionally cointegrated panels with fixed effects. The test development is based on bivariate panel series with the regressor assumed to be fixed across cross-sectional units. The proposed test procedure accommodates any integration order between [0,1], and it is asymptotically normal under the null hypothesis. Monte Carlo experiments demonstrate that the test exhibits better size and power compared to a similar residual-based test across varying sample sizes.

While the surface of the Earth plays a key role in weather forecasting through its interaction with the atmosphere, in ensemble numerical weather predictions the uncertainty on the surface is only represented with perturbations in the parameterisations representing the surface processes. Data representing the surface, such as the land cover, are not perturbed. As fully data-driven forecasts without parameterisations are growing in importance, sampling the uncertainty on the land cover data brings a new way of making ensemble forecasts. Our work describes a method of generating ensemble land cover maps for numerical weather prediction. The target land cover map has the ECOCLIMAP-SG labels, used in the SURFEX surface model, and therefore is expected to have all relevant labels for surface-atmosphere interactions. The method translates the ESA WorldCover map to ECOCLIMAP-SG labels and resolution using auto-encoders. The land cover ensemble members are obtained by sampling the land cover probabilities in the output of the neural network. This paper builds upon the work done in a companion paper describing the high-resolution version of ECOCLIMAP-SG, called ECOCLIMAP-SG+, used for the training and evaluation of the neural network. The output map presented here, called ECOCLIMAP-SG-ML, improves upon the ECOCLIMAP-SG map in terms of resolution (from 300~m to 60~m), overall accuracy (from 0.41 to 0.63) and the ability to produce ensemble members.

The COVID-19 pandemic over the past years has shown a great need for rapid, low-cost and on-site detection of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). In this paper, an aptamer-based colloidal gold nanoparticle lateral flow test strip was well developed to realize the visual detection of wild type SARS-CoV-2 spike protein (SP) and multiple variants. Under the optimal reaction conditions, a low detection limit of SARS-CoV-2 S protein of 0.68 nM was acquired, and the actual detection recovery was 83.3% to 108.8% for real world samples. This suggests a potential tool for the prompt detection of SARS-CoV-2 with good sensitivity and accuracy, and a new method for the development of alternative antibody test strips for the detection of other viral targets.

Landscape changes based on spectral responses allow showing plant cover changes through diversity, composition, and ecological connectivity. The spatial and temporal vegetation dynamics of the Bijagual Massif from 1986 to 2021 were analyzed as a measure of ecological integrity, conservation, and territory. The covers identified were high open forest (Hof), dense grassland of non-wooded mainland (Dgnm), a mosaic of pastures and crops (Mpc), lagoons (Lag), and bare and degraded lands (Bdl). The Bijagual Massif has 8,574.1 ha. In 1986, Dgnm occupied 42.6% of the total area, followed by Mpc (32.8%) and Hof (24.5%); by 2000, Mpc and Hof increased (43.7 and 28.1%, respectively), while Dgnm decreased (28%); by 2021, Dgnm was restricted to the northeastern zone and continued to decrease (25.2%), Mpc occupied 52.9%, Hof 21.7% and Bdl 0.1%. Of the three fractions of the connectivity probability index, only dPCintra and dPCflux contribute to ecological connectivity. Hof and Dgnm show patches with biota habitat quality and availability. Between 1986 and 2021, Dgnm lost 1,489 ha (41%) and Hof 239.5 ha (11%). Mpc replaced various covers (1,722.2 ha; 38%) in 2021. Bijagual has a valuable biodiversity potential limited by Mpc. Territorial planning and sustainable agroecological and ecotourism proposals are required due to the context of the ecosystems.

This study delves into the intricate interplay of economic growth components, specifically focusing on Consumption and investment in Saudi Arabia from 2000 to 2022. Employing vector error correction models and cointegration techniques, we analyze the short- and long-term dynamics within the relationship of Consumption, investment, and economic growth. Granger causality analysis is also used to discern these pivotal variables' causal connections. Our empirical analysis reveals a persistent long-term cointegration relationship among the variables, underscoring the enduring nature of their interdependency. Furthermore, our findings highlight Consumption and investment's statistically significant positive impact on economic growth. Notably, the short-term analysis unveils a stable model characterized by an annual adjustment to equilibrium of 100%.Moreover, the Granger causality study demonstrates unidirectional causal linkages between Consumption, investment, and economic growth. These findings hold substantial implications for policy formulation in Saudi Arabia. Policymakers must grasp the ramifications of burgeoning prosperity and evolving private consumption patterns on future environmental outcomes. Achieving sustainable long-term results necessitates equal emphasis on bolstering private Consumption and fostering other facets of economic growth.

Image classification in Remote Sensing and Geographic Information Systems (GIS) containing various land-cover classes is essential for efficient and sustainable land-use estimation, and other tasks like object detection, localization and segmentation. Deep Learning (DL) techniques have shown a tremendous potential in the GIS domain. While Convolutional Neural Networks (CNN) have dominated most of the image analysis domain, a new architecture called transformers have proved to be a unifying solution for several AI-based processing pipelines. Vision Transformers (ViT), a variant of transformers can have comparable and in some cases better accuracy than a CNN. However, they suffer from a significant drawback associated with an excessive use of training parameters. In this research we explore several modifications in the vision transformer architectures, especially MobileViT that can be optimized while boosting accuracy. To verify our proposed approach these new architectures are trained on four land-cover datasets AID, EuroSAT, UC-Merced, and WHU-RS19. Experiments reveal that combination of lightweight convolutional layers including ShuffleNet along with depthwise separable convolutions and average pooling can reduce the trainable parameters by 17.85% and yet achieve higher accuracy than the base MobileViT. It is also observed that utilizing a combination of convolution layers along with multi-headed self attention layers in MobileViT variants provide better performance in capturing local and global features unlike the standalone ViT architecture that utilizes almost 95% more parameters than the proposed MobileViT variant.

The Geopyörä breakage test uses two counter-rotating wheels to nip and crush rock specimens with a tightly controlled gap between rollers. The force applied and energy consumed during breakage are measured with instrumentation. In contrast to drop weigh test (DWT) methods, the breakage energy is a response to the rock compressive strength and degree of compression, not a controlled test input, such as the kinetic input energy of a falling weight. This paper presents the detailed measures conducted to evaluate the accuracy and precision of energy measurements across various ore types using the Geopyörä device. While force measurement was assessed just for its precision. The outputs are compared directly to the DWT measures of fragmentation at the same energy and fitted A and b parameters. The test reproducibility was evaluated using a Round-Robin methodology, testing several samples in multiple laboratories. The results confirmed that the new test has sufficient accuracy to match DWT results and excellent precision to assure reproducibility.

We develop a primality test for Mersenne numbers and investigate the primality of the sequence of Catalan-Mersenne numbers. We use induction as a proof to show that the 5th Catalan-Mersenne number is a prime number, thus demonstrating the infinitude of Mersenne primes.

The BH 25 railway bridge, located in Indonesia, consists of three spans: 9.5 m (span-1 girder type), 21.9 m (span-2 truss type), and 9.6 m (span-3 girder type). Despite the initial plan for camber, it was not achieved, leading to the installation of temporary support on span-2. To assess the level of damage and determine the necessary steps, static and dynamic tests were conducted using a CC206 locomotive. The maximum deflection was recorded at -4.60 mm for span-1, -11.30 mm for span-2, and -3.42 mm for span-3. The dominant frequency in the vertical direction of span-2 was found to be 14.65 Hz. Due to the inability to achieve the planned camber and the subsequent removal of temporary support, external prestressing will be implemented, resulting in a camber of 11.82 mm. This change in prestressing also affects the dominant frequency of span-2, which becomes 17.07 Hz.

Oil and Gas companies, both national and international, along with government regulators, share a common goal of efficiently managing their valuable assets. These assets refer to the Reserves of oil and Gas located underground. Typically, production and Reserves Engineers play a crucial role in managing these reserves through the implementation of well testing techniques. Thus far, the gold standard in this field has been to ensure the optimal management and utilization of these resources. In the context of well testing, the separator has traditionally been considered the gold standard. However, despite regulatory mandates for frequency of well testing (Such as the general requirements of every 30days in the Nigeria south East zone sector), There is a lack of specific regulations regarding the expected flow measurement uncertainties. This gap in the regulations leaves room for improvement in establishing guidelines for accurate flow measurements. This paper aim to Review the various test separator employed, examine the implications of the 30days testing interval under real - world conditions, and critically assess the achievable measurements uncertainties in the field. Additionally, it will provide a candid analysis that sheds light on the expected uncertainties associated with flow measurements. The introduction of the multiphase meters in the past two decades hold the potential for significant advancements in Reservoirs management performance. However, the authors suspect that this potential has not been universally realized. This paper aim to address this issue by examining the extent to which the benefits of multiphase meters have been effectively utilized in reservoir management. By doing so, it seeks to shed light on any existing gaps and propose recommendation for maximizing the impact of multiphase metres in the field. In addition to the aforementioned objectives, this paper will also address and explore the following key aspects:Identification and review of both the strength and weaknesses associated with test separators. By thoroughly examining these attributes, we can gain valuable insight into their effectiveness and potential areas for improvement. Exploration of alternative application of test separator and their impact on well testing efficiency. Real -World comparison will be provided to highlight the advantages and challenges associated with these alternative uses, offering a comprehensive understanding of their implications. Evaluation of the contribution that multiphase flows meters (MPFMs) can bring to the testing scenario and overall performance. By assessing the capabilities and potential benefits of MPFMs, we aim to provide a comprehensive picture of their role in enhancing testing procedures. Examination of the flow measurement uncertainties that can be expected from a test separator and their potential impact on reservoirs management performance. By understanding and quantifying these uncertainties, we can gain insight into how they may affect decision -making and optimization strategies in managing our materials assets effectively. Delving into the question of reconciling multiphase flow meter (MPFMs) with test separators. This analysis aims to inject a sense of realism into the world of managing our major material assets by explaining the challenges and opportunities associated with integrating and aligning these two measurement technologies. By addressing these crucial aspects, this paper strives to provide a comprehensive understanding of the complexities involved in managing our material assets, ultimately driving towards more informed decision-making and improved performance.

Background: Open AI developed ChatGPT, a language model based on the GPT architecture, designed for text-based communication. Trained on diverse internet texts, ChatGPT generates contextually appropriate responses using machine learning. It understands input through analysis and context interpretation, generating coherent and contextually relevant responses. Interaction is possible through messaging platforms. Materials and Methods: In November 2023, we utilized ChatGPT 3.5, the default version at that time, to answer questions from the Italian National Residency Program Admission Tests (SSMs) of 2021, 2022, and 2023. The questions cover clinical, diagnostic, analytical, therapeutic, and epidemiological scenarios, sometimes accompanied by images. The study compared ChatGPT's answers to the official corrections on the Italian Ministry of University and Research (MUR) website. The scoring method used for evaluation was 1 point for correct answers, 0 points for unanswered questions, and -0.25 points for incorrect answers, reflecting the SSM test scoring system. Results: In summary, ChatGPT was tested with a total of 420 questions, 140 for each test. It achieved an overall accuracy of 80.48%, providing correct answers for 338 questions and incorrect answers for 82 questions. When faced with questions containing both text and images, it answered 55% correctly and 45% incorrectly. The model's performance varied over time, with an 82.14% accuracy rate in 2021 and 2022 (115 correct out of 140) and a 77.14% accuracy rate in 2023 (108 correct out of 140). Applying thisscoring method to the SSM test, ChatGPT would have scored 105 points in 2021 and 2022, and 100 points in 2023. Conclusions: ChatGPT has exhibited above-average performance in the last three SSM tests, highlighting its robust capability to interpret clinical scenarios and offer precise diagnostic and therapeutic guidance. Despite this, some limitations persist, notably the software's inability to interpret non-textual information.

Land Use Land Cover (LULC) changes analysis is one of the most useful methodologies to understand how the land was used in the past years, what types of detections are to be expected in the future, as well as the driving forces and processes behind these changes. In Ethiopia, the rapidly changing of LULC is mainly due to population pressure, resettlement programs, climate change, and other human and nature-induced driving forces. Anthropogenic activities are the most significant factors adversely changing the natural status of the landscape and resources, which exerts unfavourable and adverse impacts on the environment and livelihood. The main goal of the present work is to review previous studies, discussing the spatio-temporal LULC changes in Ethiopian basins, to find out common points and gaps that exist in the current literature, to be eventually addressed in the future. Seventeen articles, published from 2011 to 2020, were selected and reviewed, focusing on LULC classification using ArcGIS and ERDAS imagine software by unsupervised and maximum likelihood supervised classification methods. Key informant interview (KII), focal group discussions (FGDs) and collection of ground truth data using ground positioning systems (GPS) for data validation were the major approaches discussed in most of the studies. All the analysed research showed that, during the last decades, Ethiopian lands changed to agricultural land use, waterbody, commercial farmland and built-up/settlement. Some parts of forest land, grazing land, swamp/wetland, shrubland, rangeland and bare/ rock out cropland cover class were changed to other LULC class types, mainly as a consequence of increasing anthropogenic pressure. In summary, these articles confirmed that LULC changes are a direct result of both natural and human influences. However, most of the study provided details of LULC for the past decades within a specific spatial location, while they did not address the challenge of forecasting future LULC changes at the basin scale.

Cameroon territory is experiencing significant land use and land cover (LULC) changes since its independence in 1960. But the main relevant impacts are recorded since 1990 due to intensification of agricultural activities and urbanization. LULC effects and dynamics vary from one region to another according to the type of vegetation cover and activities. Using remote sensing, GIS and subsidiary data, this paper attempted to model the land use and land cover (LULC) change in the Centre Region of Cameroon that host Yaoundé metropolis. The rapid expansion of the city of Yaoundé drives to the land conversion with farmland intensification and forest depletion accelerating the rate at which land use and land cover (LULC) transformations take place. This study aims at assessing the impacts of both agriculture and urbanization on the LULC change in the Centre Region of Cameroon. A detailed LULC map from MAPBOX high resolution images and three LULC maps were produced from Landsat TM-OLI images (1984-2015). A maximum likelihood classification techniques using ERDAS Imagine, showed forest decline with a total loss of 54% in thirty years. Also, Landsat and MAPBOX images to which we added 1951 aerial photograph and SPOT 6 (2006) were used to analyse urban growth in the city of Yaoundé. The results show a remarkable urban spatial spread of the metropolis between 1951 and 2015, with a peak in 2000. Images processing enabled us to analyse the long term dynamics of LULC change since the 1950s in this Region using ArcGIS & QGIS software’s. Based on this dynamic, a LULC projection map was produced using Markov model on IDRISI Selva, demonstrating the decrease of the dense forest (45% in 2015 to 0.25% in 2050). It was estimated that by 2050, the entire dense forest can be depleted if nothing is done, while only 12.67% of the secondary forest would remain in the Region. Such a projected map is very useful to decision makers for council development and urban planning. This effective forest depletion ties with the hypothesis that urbanization of Yaoundé and its secondary surrounding satellite cities (within a radius of 30-100km) is a veritable driving force of deforestation.

Land Surface Temperature (LST) and Land Use Land Cover (LULC) are the principal aspects of climate and environment studies. The object of the study is to assess spatial relationship between LST and remote sensing LULC indices at the global and continental scale. Moderate Resolution Imaging Spectroradiometer (MODIS) Aqua daytime LST and eight LULC MODIS indices of 2018 prepared and processed using Earth Engine Code Editor. R squared and significance of the relationship values of randomly selected points computed in R program. The research observed the relationship between examined indices and LST is significant at the 0.001 level. Normalized Difference Water Index (NDWI) and Normalized Difference Snow Index (DSI) are the dominant drivers of LST in the world, Asia and North America. In Australia and Africa, Normalized Difference Vegetation Index (NDVI) and Enhanced Vegetation Index (EVI) are the dominant drivers of LST. Albedo and Normalized Difference Soil Index (NDSI) have superior in Central America. In South America and Europe, the dominant driver of LST is NDWI. Relationship between albedo and LST is moderate inverse on a global scale. Observed relationship between LST and examined vegetation indices is positive in Europe and North America while inverse in Australia and Africa. All observed relationship between Normalized Difference Built-up Index (NDBI) and LST are positive. Association observed between NDSI and LST is positive in Australia, Africa and Central America.

Background: Diet is a risk factor for gestational diabetes mellitus (GDM). There are few studies on women´s diet and glucose tolerance test (GTT) results. Objective: To evaluate the relationship between previous diet and the number of abnormal values on the diagnostic GTT in women with GDM. We hypothesized there would be an inverse relation between antioxidant micronutrient consumption and the number of abnormal GTT values. Methods: This cross-sectional study included 60 women diagnosed with GDM (2-hours, 75g-GTT). Shortly after diagnosis, participants answered a validated food frequency questionnaire to assess food consumption in the last 6 months. Mann-Whitney´s test was used to compare the dietary intake of participants with one (group 1) versus two-three (group 2) abnormal GTT values. Results: Participant characteristics were similar. There were no significant differences between groups in median intake of total calories, carbohydrates, lipids and proteins. Participants in group 1 had significantly higher intakes of fiber (11.9 vs. 11.0 g/day p= 0.049), vitamin D (40.6 vs. 40.4 mcg/day p= 0.049) and vitamin C (180.0 vs. 151.0 mg/day p= 0.008) than those in group 2. Conclusion: Results suggest a possible association between consumption of fiber and some antioxidant micronutrients and GDM severity at the time of diagnosis.

Speckle Plethysmography (SPG) and Photoplethysmography (PPG) are different biophotonics technologies that allow for measurement of hemodynamics. As the difference between SPG and PPG under low perfusion conditions is not fully understood, a Cold Pressor Test (CPT) was used to modulate blood pressure and peripheral circulation. A custom-built setup simultaneously derived SPG and PPG from the same video streams at two wavelengths (639 nm and 850 nm). SPG and PPG were measured at right index finger location before and during CPT using finger Arterial Pressure (fiAP) as reference. The effect of CPT on Alternating Component amplitude (AC) and Signal-to-Noise-Ratio (SNR) of dual-wavelength SPG and PPG signals was analysed across participants. Furthermore, waveform differences between SPG, PPG, and fiAP based on frequency harmonic ratios, were analysed for each subject (n=10). Both PPG and SPG at 850 nm show a significant reduction during CPT for both AC and SNR. However, SPG showed significantly higher and more stable SNR than PPG in both study phases. Harmonic ratios were found substantially higher in SPG than PPG. Therefore, in low perfusion conditions, SPG seems to offer a more robust pulse wave monitoring with higher harmonic ratios than PPG.

Nowadays, some coffee production centers are still classification manually, so it requires a very long time, a lot of labor, and expensive operational costs. Therefore, the purpose of this research was to design and performance of the coffee bean classifier that can accelerate the process of classification beans. The classifier used consists of three main parts, namely the frame, driving force, and sieves. Research parameters include classifier work capacity, power, specific energy, classification distribution and effectiveness, and efficiency. The results showed that the best operating conditions of the coffee bean classifier was found at a rotational speed of 91.07 rpm and a 16° sieves angle with a classifier working capacity of 38.27 kg/h, the distribution of the seeds retained in the first sieve was 56.77 %, the second sieves was 28.12%, and the third sieves was 15.11%. The efficiency of using a classifier was found at a rotating speed of 91.07 rpm and a sieves angle of 16°. This classifier was simple in design, easy to operate, and can sort coffee beans into three classification, namely small, medium, and large.

In this paper, Lie symmetry and Painlevé Techniques are applied to the SIRD (Susceptible, Infected, Recovered and Dead) model. A demonstration of the integrability of the model is provided to present an exact solution. The study revealed that nonlinear system passes Painlevé test and does not possesses complex chaotic behaviour. However, the system fails to pass the Painlevé test while constraints reach values equivalent to the corresponding complex chaotic behaviour. The two-dimensional Lie symmetry algebra and the commutator table of the infinitesimal generators are obtained. Lie symmetry analysis serves to linearize the nonlinear system and find the corresponding invariant solution.

In this paper, polyurethane concrete (PUC) is used as wire embedding material to form a new polyurethane concrete- prestressed steel wire (PUC-PSW) reinforcement method. The lightweight and high-strength PUC materials not only bond and anchor the prestressed steel wire (PSW), but also passively participate in the structural force. The problems caused by using mortar or composite mortar as the embedding material are avoided. Twelve reinforced concrete T-beams were tested for PUC-PSW flexural reinforcement. It consists of 1 unreinforced beam, 4 PSW reinforced beams, and 7 PUC-PSW reinforced beams. The wire embedding material, wire anchorage form, PUC material depth, amount of wire, and loading type were used as variables. The test results show that PUC-PSW reinforcement can obviously enhance the flexural load and ultimate load of the reinforced beams compared with PSW reinforcement. The ability of PUC-PSW reinforcement to limit crack development is better than that of PSW reinforcement beam, especially after the main beam steel yield. The strength, stiffness and crack limiting ability of the reinforced beam increase with the PUC thickness of the reinforced layer.

The conversion of LULC classes into other types is occurring at a faster rate globally including United States. Many studies have examined the drivers and causes of LULC changes, particularly, in northeast Georgia and Atlanta in the United States, while the case of southeast Georgia remains unstudied. Thus, this study filled the gap by quantifying and predicting the impact of LULC change on forestlands and how these LULC changes have affected forest health. The study used Landsat images, including 2005 and 2023 together with the random forest algorithm to perform LULC classification on the Google Earth Engine. Also, the study predicted how LULC will impact forest cover by 2050. The results revealed that forest hectares have generally changed approximately from 65% to 62% between 2005 and 2023, and this is projected to likely further decline to about 53% by 2050. This change in forest acreage has resulted decline in the health of the forest, that is the NDVI values changed from 0.992 to 0.866 between 2005 and 2023. The study concludes that the forest cover in southeast Georgia has changed to urban features over the years. Agriculture land is projected to gain most of the forest cover by 2050.

Thermal stresses belong to the leading factors that influence low-temperature cracking behavior of asphalt pavements. During winter, when temperature drops to significantly low values, tensile thermal stresses develop as a result of pavement contraction. Creep test methods can be suitable for the assessment of low-temperature properties of asphalt mixtures. To evaluate the influence of creep test methods on the obtained low-temperature properties of asphalt mixtures, three point bending and uniaxial tensile creep tests were applied and the master curves of stiffness modulus were analyzed. On the basis of creep test results, rheological parameters describing elastic and viscous properties of the asphalt mixtures were determined. Thermal stresses were calculated and compared to tensile strength of the material to obtain the failure temperature of the analyzed asphalt mixtures. It was noted that lower strain values of creep curves were obtained for the Tensile Creep Test (TCT) than for the Bending Beam Creep Test (BBCT), especially at lower temperatures. Results of thermal stress calculations indicated that higher reliability was obtained for the viscoelastic Monismith method based on the TCT results than for the simple quasi-elastic solution of Hills and Brien. The highest agreement with the TSRST results was also obtained for the Monismith method based on the TCT results. No clear relationships were noted between the predicted failure temperature and different methods of thermal stress calculations.

(1) Background: Cardiorespiratory fitness (CRF) is a prognostic factor regarding long time morbidity and mortality. To assess CRF the well-known gold standard is cardiopulmonary exercise testing (CPET), which is a time consuming and expensive test. Therefore, alternative methods for routine evaluation of CRF are needed for the general population as well as for specific patient groups such as children and young adults with congenital heart disease. The Stair Climbing Test (SCT) is a simple and resource saving test reported in the current literature. This test is used in various settings to assess different health associated risk factors including cardiorespiratory fitness, muscular resilience, therapy effectiveness or pre- and postoperative morbidity and mortality.

The presence of anti SARS-CoV2-RBD antibody (Anti-RBD) prevents severe COVID-19. We aimed to determine the accuracy of a point-of-care Anti-RBD test implemented in person living with HIV (PLWH), systemic lupus erythematosus (SLE), and chronic kidney disease (CKD). We enrolled 182 non-comorbid subjects and 335 persons with comorbid (PLWH, SLE, CKD) to test anti-RBD assay compared to surrogate viral neutralization (SVNT) as the reference test. We performed linear correlation analysis between anti-RBD vs SVNT and a ROC analyses to ascertain anti-RBD cut-off at 30%, 60%, and 90% inhibition of SVNT to calculate accuracy. Correlations of anti-RBD to SVNT among all groups were excellent with R= 0.7903, R=0.7843, R=0.8153 among non-comorbid, SLE and CKD groups, respectively, with significantly higher correlation among the PLWH group (R=0.8877; p-value=0.0072) compared to non-comorbid group. The accuracy of the anti-RBD test among PLWH and CKD group was similar with the non-comorbid but showed lower sensitivity in the SLE group (p=0.000014). The specificity of the test remained high in all groups. In conclusion, the Anti-RBD test had excellent correlation to SVNT. The persistently high specificity in all groups suggests that this test can be reliably utilized to detect presence of low neutralization capacity, prompting additional vaccination.

The role of trees in watershed hydrology is governed by many environmental factors along with their inherent characteristics and not surprisingly has generated into diverse debates in the literature. Herein, this state-of-the-art review provides an opportunity to propose a conceptual model for understanding the role of trees in watershed hydrology and examine the conditions under which they can be an element that increases or decreases water supply in a watershed hydrology. To achieve this goal, this review addressed the interaction of forest cover with climatic conditions, soil types, infiltration, siltation and erosion, water availability, and the diversity of their ecological features. The novelty of the proposed conceptual model highlights that tree species and densities, climate, precipitation, type of aquifer, and topography are important factors affecting the relationships between trees and water availability. This suggests that forests can be used as a nature-based solution for conserving and managing natural resources, including water, soil and air. To sum up, forests can reduce people’s imprint, thanks to their role in improving water and air quality, conserving soil, and other ecosystem services. The outcomes of this study should be valuable for decision-makers when investing in reforestation in a watershed hydrology.

Land use and land cover (LULC) datasets for Jinan in 1992, 1998, 2002, 2006, 2011, 2017, and 2022 were developed from Landsat images using the Random Forest (RF) classification approach. The relationships between social-economic, political factors and time-series LULC data were exam-ined for the periods between 1992 and 2022. The results showed the effectiveness of using the RF classification method for LULC classification with time series of Landsat images. Combined with driving forces analysis, our research can effectively explain the detailed LULC change tra-jectories corresponding to different stages and give new insights into Jinan LULC change pat-terns. The results show a significant increase in impervious surface which opposite change to bare land which experienced a huge decline declined by 95%, due to urbanization and rapid in-crease of population. The driving forces behind these changes are related to population growth, economic development, and climate change. Moreover, the present research employed Principal Components Analysis (PCA) methodology in order to understand the relative significance of disparate driving factors. The analysis results prove that the economy (population, GDP) and climate change were the primary factors that have an obvious impact on land use/land cover changes and that the driving factors for impervious surface, bare land, woodland, farmland, and water were distinct. Government policies also have a substantial impact on LULC change as well, such as the Construction of Harmonious Jinan (COHJ). The results were helpful for better understanding the mechanisms of LULC change and can provide useful knowledge for effective land resource management and planning.

This study introduces and demonstrates a comprehensive, accurate, unbiased approach to robust quantitative comparison of Electronic Nicotine Delivery Systems (ENDS) appropriate for establishing substantial equivalence (or lack thereof) between tobacco products. The approach is demonstrated across a family of thirteen pen- and pod-style ENDS products. Methods employed consist of formulating a robust emissions surface regression model, quantifying the empirical accuracy of the model as applied to each product, evaluating relationships between product design characteristics and maximum emissions characteristics, and presenting results in formats useful to researchers, regulators, and consumers. Results provide a response surface to characterize emissions (total particulate matter and constituents thereof) from each ENDS appropriate for use in a computer model and for conducting quantitative exposure comparisons between products. Results demonstrate that emissions vary as a function of puff duration, flow rate, E-Liquid composition, and device operating power. Further, results indicate that regulating design characteristics of ENDS devices and consumables may not achieve desired public health outcomes; it is more effective to regulate maximum permissible emissions directly. Three emissions outcome measures (yield per puff, mass concentration and constituent mass ratio) are recommended for adoption as standard quantities for reporting by manufacturers and research laboratories. The approach provides a means of (a) quantifying and comparing maximal emissions from ENDS products spanning their entire operating envelope, (b) comparative evaluation of ENDS devices and consumable design characteristics, and (c) establishing comparative equivalence of maximal emissions from ENDS. A consumer-oriented product emissions dashboard is proposed for comparative evaluation of ENDS exposure potential. Maximum achievable power dissipated in the coil of ENDS is identified as a potentially effective regulatory parameter.

I propose a test for machine self-awareness inspired by the Turing test. My test is simple, and it provides an objective, empirical metric to rectify the ungrounded speculation surging through industry, academia, and social media. Drawing from a breadth of philosophical literature, I argue the test captures the essence of self-awareness, rather than some postulated correlate or ancillary quality. To begin, the concept of self-awareness is clearly demarcated from related concepts like consciousness, agency, and free will. Next, I propose a model called the Nesting Doll of Self-Awareness and discuss its relevance for intelligent beings. Then, the test is presented in its full generality, applicable to any machine system. I show how to apply the test to Large Language Models and conduct experiments on popular open and closed source LLMs, obtaining reproducible results that suggest a lack of self-awareness. The implications of machine self-awareness are discussed in relation to questions about meaning and true understanding. Finally, some next steps are outlined for studying self-awareness in machines.

The SARS (severe acute respiratory syndrome)-CoV (Coronavirus)-2 S(spike)-protein mRNA/cDNA currently being used as vaccines are antigenic but not antigens against SARS-CoV-2, that causes COVID (Coronavirus Disease) -19. Furthermore, the mRNA and cDNA antigenic vaccines also have potentials for homologous as well as heterologous recombination, primarily into the somatic cell DNA of the vaccine recipients. On the contrary, a SARS-CoV-2 RBD-protein antigen, a part of the S-protein, will directly stimulate antibody production against SARS-CoV-2. Hence, a vaccine composed of SARS-CoV-2 RBD-protein as a safer, fast acting, and effective vaccine against SARS-CoV-2 and thus against COVID-19. This is also useful for some immune compromised individuals.

Taking a certain type of test centrifuge as the research object, the finite element model of the test centrifuge is established, the vibration characteristics and aerodynamic performance of the test centrifuge are analyzed, and the structural optimization design of the test centrifuge is carried out. In this paper, the load is applied according to the actual working condition of a certain type of test centrifuge. The vibration of the mounting seat of the test centrifuge is analyzed and the structure of the mounting seat is optimized. After optimization, the vibration of the mounting seat is 77.38 % lower than that of the original mounting seat. Then, the aerodynamic analysis of the test centrifuge is carried out. The analysis results show that the test centrifuge moves more smoothly under the whole package shell and the steady flow shell, and the resistance decreases and the shaft load decreases. Finally, the steady flow shell of the test centrifuge is optimized. The analysis shows that the increase of the width of the steady flow shell can reduce the resistance coefficient, which is helpful to the stability of the test centrifuge during operation and reduces the unbalanced response of the system caused by air resistance.

Due to urban sprawls, the arable land is shifting in the settlement areas and towns, while industrial development is making it more vulnerable. The current study was conducted to see the changes in land use and land cover in Kotri area, Pakistan from 1998 to 2020 to establish trends in recent land use development based on available land use data. In this regard, satellite images in the study area were acquired from USGS and processed using ArcMap 10.5 and Environmental for Visualizing Images (ENVI). Results show that; there was a change in the settlement pattern of Kotri city with 40% between 1998 and 2020, 77% decrease in Bare-land was observed in 2020. Natural vegetation in the study area has decreased significantly with 4.4 Sq/ km in 2020, surface water-bodies in 1998 were 1.3 sq/km and in 2020 there is 1.8 Sq/km indicating 32% increase in surface water bodies. It was further revealed that settlement in Kotri has increased due to its geographical location, nearness of the major city of Hyderabad, and the establishment of the industrial zone and educational city near Kotri. From the foregoing, the study concluded that Kotri City will have more changes in its land use and land cover as the expansion in the city is going on and on. It is therefore recommended that local government and provincial government should pay attention towards this development and put up an action plan towards proper provision for such expansion.

(1) Background The SKT is a short cognitive performance test designed to assess impairments in memory and cognitive abilities such as attention and speed of information processing. In 2019, new regression-based norms for the English version of the SKT were calculated applying data from older cognitively healthy adults living in the US, Ireland and Australia (the norming sample) The study has two aims: to establish valid cut-offs for distinguishing between no cognitive impairment, mild cognitive impairment (MCI) and dementia (1), and to cross-validate the new norms for detecting MCI and dementia (2) in a community sample of older adults with clinical diagnoses; (2)Methods: The validation sample included 142 older adults (mean age=87.7, SD=3.55) from the Sydney Memory and Aging Study (MAS Study). Participants were classified as having normal cognition, MCI, or dementia through a consensus diagnosis as well as by the SKT; (3)Results: The sensitivity of the SKT for the differentiation of cognitive impairment (MCI or dementia) from normal cognition was 80.6%. The convergence between the SKT and the consensus diagnoses was 60.1% for all three diagnostic groups. The correlation between the SKT and the Addenbrooke’s Cognitive Examination III (ACE-III), a well validated measure of cognitive ability in older adults, was r = 0.3;. (4) Conclusions: In sum, it can be stated that the SKT is a valid tool for detecting early stages of cognitive impairment, performing very well in discriminating between no cognitive impairment and cognitive impairment (MCI or dementia).

The results reveal CILSS as the most accurate data set with a Kappa coefficient of 68% and an overall accuracy of 83%. CILSS data shows a decrease of savanna and forest whereas an increase of cropland over the period 1975 to 2013. The increase of cropland area of 30.97% from 1975 to 2013 can be related to the increase in population and their food demand, while the losses of forest area and the decrease of savanna are further amplified by using wood as energy sources and the lack of forest management. The three datasets were used to simulate future LULC changes using the Terrset Land Change Modeler. The validation of the model using CILSS data for 2013 showed a quality of 50.94%, it is only 40.04% for ESA and 20.13% for Globeland30. CILSS data was utilized to simulate the LULC distribution for the years 2020 and 2027 because of its satisfactory performances. The results show that a high spatial resolution is not a guarantee of high quality. The results of this study can be used for impact studies and to develop management strategies for mitigating negative effects of land use and land cover change.

Despite the overall extension of the Amazon basin (approximately 6,000,000),which encompasses such a complex ecosystem and territories belonging to seven different nations, it is worth mentioning that environmental assessment related to changes in land use and land cover (LULC) in this region are often conducted respecting geopolitical boundaries associated with each country or taking into account the so-called Amazon biome. With the purpose of prospecting the intricate and hidden hydrological patterns, we undertake an in-depth evaluation of the water balance along the 2001-2021 time span across the whole basin, whose behavior depends on the features deriving from the metamorphoses in land use and land cover. To accomplish that task, the influence of the components of the water balance, namely rainfall and evapotranspiration, jointly with the terrestrial topographic mapping, are examined to investigate the interactions among the physical mechanisms that make up the hydrological cycle and the corresponding physical hydrological processes triggered by deforestation and reforestation in the region. More specifically, the modeling approach was rigorously designed to also consider, separately or not Negro, Solimões, Madeira, Tapajós and Xingu hydrographic sub-basins, which are the most important ones of the Amazon basin. The results highlight that, in the southern region of the Amazon, specifically within the Madeira river sub-basin, the lowest forest coverage is observed (56.0%), whereas in the northern Negro river sub-basin, the most notable forest coverage is observed (85.0%).The most preserved forest areas, such as the Negro and Solimões river sub-basins, with percentages of 81.9% and 74.2%, respectively, have higher annual rates of precipitation and evapotranspiration over time. On the other hand, regions that suffered the most intense deforestation along the time period studied, such as the Madeira, Tapajós and Xingu sub-basins, have lower annual rates of precipitation and evapotranspiration, with a preservation percentage of 54.6%, 62.6% and 70, 7%, respectively. As the pace of deforestation slowed between 2003 and 2013, annual precipitation rates increased by 12.0%, while evapotranspiration decreased by 2.0%. The hydrological findings of this paper highlight th predominant role of the forest in the context of the global water balance of the Amazon basin and the potential to also produce distinct impacts within different parts of the basin in terms of having more or less rainfall and evaporation. In addition, those variabilities in the hydrological operational components and mechanisms due to changes in land cover and land use also reveals the potential impacts that could be expected in the surrounding areas, closer or farther, notably beyond the limits of the Amazon basin.

Remote sensing/GIS techniques are a versatile tool for x-raying serial forest structural changes in retrospect. It would be impossible to evaluate past occurrences and changes in forest extents in past decades at Effan Forest Reserve without non-conventional means. Therefore, we adopted remote sensing technology using Landsat images to evaluate land-use change and degradation rates in the area with a view to ascertaining causal factors for possible minimization of forest degradation in Effan Forest Reserve. Land-use/land-cover changes were analyzed using USGS-Landsat TM and ETM images of 1987, 2002, 2014 and 2019. Field-data were collected using handheld GPS receiver and spatial statistical analyses were conducted using the ground control points (GCPs). For inventory data, a systematic sampling technique was adopted using ten 1.05 km-transects at 500 m intervals. A total of 50 sample plots of 50 × 50 m were used. All tree species with Dbh ≥10 cm were enumerated. Nineteen tree species in ten families were encountered with Vitellaria paradoxa as the most-frequently occurring species in the area. IUCN-listed endangered Pterocarpus erinaceus, hitherto abundant in the area, was rarely encountered during the survey, while Vitellaria paradoxa is gradually shrinking, going the relative abundance in the area. The result further showed that primary and secondary forests decreased considerably by 258.03 ha (46.72%) and 9.18 ha (3.63%), respectively, with a total forest loss of 50.3% in 32 years (8.4 hayr-1, 1.6% per annum). While forest plantation size doubled by 369.72 ha within the period. This is worrisome as the remaining fragmented forests appeared to be on the decline, except the riparian vegetation, due to inaccessibility to the riparian by loggers. It thus appeared that forest protection approaches were ineffective. Increased protection efforts could save this forest reserve, and the concerned authority should consider a focused-enrichment planting involving indigenous species for ecosystem-repair.

Deep learning classification is the state-of-the-art of machine learning approach. Earlier work proves that the deep convolutional neural network has successfully and brilliantly in different applications such as images or video data. Recognizing and clarifying the remote sensing aspect of the earth's surface and exploit land cover and land use (LCLU). First, this article summarized the remote sensing emerging application and challenges for deep learning methods. Second, we propose four approaches to learn efficient and effective CNNs to transfer image representation on the ImageNet dataset to recognize LCLU datasets. We use VGG16, Inception-ResNet-V2, Inception-V3, and DenseNet201 models to extract features from the EACC dataset. We use pre-trained CNNs on ImageNet to extract features. For feature selection we proposed principal component analysis (PCA) to improve accuracy and speed up the model. We train our model by multi-layer perceptron (MLP) as a classifier. Lastly, we apply the multi-granularity encoding ensemble model. We achieve an overall accuracy of 92.3% for the nine-class classification problem. This work will help remote sensing scientists understand deep learning tools and apply them in large-scale remote sensing challenges

Due to urban sprawls, the arable land is shifting in the settlement areas and towns, while industrial development is making it more vulnerable. The current study was conducted to see the changes in land use and land cover in Kotri area, Pakistan from 1998 to 2020 to establish trends in recent land use development based on available land use data. In this regard, satellite images in the study area were acquired from USGS and processed using ArcMap 10.5 and Environmental for Visualizing Images (ENVI). Results show that; there was a change in the settlement pattern of Kotri city with 40% between 1998 and 2020, 77% decrease in Bare-land was observed in 2020. Natural vegetation in the study area has decreased significantly with 4.4 Sq/ km in 2020, surface water-bodies in 1998 were 1.3 sq/km and in 2020 there is 1.8 Sq/km indicating 32% increase in surface water bodies. It was further revealed that settlement in Kotri has increased due to its geographical location, nearness of the major city of Hyderabad, and the establishment of the industrial zone and educational city near Kotri. From the foregoing, the study concluded that Kotri City will have more changes in its land use and land cover as the expansion in the city is going on and on. It is therefore recommended that local government and provincial government should pay attention towards this development and put up an action plan towards proper provision for such expansion.

Failaka Island is located 20 kilometers east of the Kuwait mainland. The island includes archaeological sites dating back to the Bronze, Hellenistic, Christian, and Islamic ages. To develop the island as a tourist attraction the state is pursuing a new urban plan based on the island's environmental potential. This study is the basis of the urban plan depends on environmental criteria from the view of Geoarchaeology. The study analysis the land-use and land-cover changes of Failaka Island between 1958- 2018. It provides a topographic survey of the island's coastline and a classification of its geomorphological features and a state of the art identification of its archaeological sites by using a drone to make a terrain model. The study used a medium to high-resolution image analysis of the land-use and land-cover changes: WorldView2-50cm 2010 and 2018; Landsat 8; aerial photography; Drone images and a digital elevation model (DEM), to analysis the expected sea level changes by the end of this century. This study also created a geodatabase of the island that can be adapted for future studies. The results emphasize the importance of preserving the historical and ecological features of the island while developing its infrastructure.

In order to study the influence of falling rock shape on its rolling characteristics and realize the optimization of falling rock protection design, the following research was carried out. Design model experiments to explore the rolling characteristics of different shapes of rockfalls. Based on the experimental results, it was found that the slenderness ratio, center of gravity, and rotational inertia of the rockfalls can affect their rolling characteristics, leading to swaying and changing the rolling axis during the rolling process, thereby affecting their rolling speed. On this basis, the formation mechanism of rolling resistance is analyzed, and the main cause of energy loss is the rolling resistance arm formed with the rolling surface during rockfall rolling, and a shape parameter to quantify the rolling resistance is proposed. The parameters are substituted into the kinematic formula, in which the influence of the rockfall shape, slope and slope roughness on the rolling speed is considered. Combined with the offset and initial position of the rockfall, the formula can be used to calculate the rolling speed and impact energy in the rolling region and any position in the region. The calculation formula was validated using model experimental data, and the results showed that the error between the experimental and calculated values was small. The error was corrected based on the experimental data. After on-site testing and verification, it can provide reference for the management of rockfall disasters.

For the symmetrical mixture model and mixture test area, the lattice point set is used to partition, and then the corresponding test statistics can be constructed. In this paper, we first proposes the partition methods under the lattice point sets and obtains several sub-simplexes without common interior points. Furthermore, we present the method for constructing a uniform design on the simplex using the center points of these sub-simplexes. The designs satisfy the uniformity of maximum distance deviation and provide good results for the mean square error deviation. Finally, the uniformity test on the mixture region is considered and illustrated by examples.

In this paper, by extending some results of informational genomics, we present a new randomness test based on the empirical entropy of strings and some properties of repeatability and unrepeatability of substrings of certain lengths. We give the theoretical motivations of our method and some experimental results of its application to a wide class of strings: decimal representations of real numbers, roulette outcomes, logistic maps, linear congruential generators, quantum measurements, natural language texts, and genomes. It will be evident that the evaluation of randomness resulting from our tests does not distinguish among the different sources of randomness (natural, or pseudo-casual).

Control of canine infections with Leishmania infantum (L. infantum), a major zoonotic disease in Brazil and southern Europe is becoming increasingly important due to their close proximity to humans, the increasing import of dogs from endemic regions and impact of climate change on vector spreading. Simple, rapid and reliable diagnostic tests are therefore needed to detect infected dogs. Here, we re-evaluated different serological methods for the diagnosis of canine leishmaniosis (CanL) in Croatia and Brazil. The diagnostic performance of the indirect fluorescent antibody test (IFAT) and the VetLine® Leishmania ELISA was compared with three rKLi8.3 based diagnostic test systems, the rKLi8.3 ELISA, the INgezim® Leishma CROM lateral flow test (LFT) and the VetBlot® Leishmania LineBlot. CanL symptomatic dogs were efficiently diagnosed by all tests, except the VetLine® Leishmania ELISA, which is based on whole Leishmania antigens. The advantage of rKLi8.3 was also observed in oligo-and asymptomatic dogs from Brazil and Croatia, although with reduced diagnostic efficiency compared to symptomatic dogs. Similar to IFAT and rKLi8.3 ELISA, the LFT did not cross-react with other common canine pathogens, showed a very high specificity for healthy dogs from endemic regions of both countries and did not react with healthy, vaccinated dogs in Brazil. In conclusion, sero-diagnostic tests based on the rKLi8.3 antigens are superior to whole parasite antigens and the LFT has the advantage of providing a laboratory independent, rapid and specific diagnosis of CanL.

In Tunisia, olive is the most cultivated fruit crop while in the north where rainfall exceeded 400mm.year-1, the olive growing area is in widely extension in marginal soil with high slope gradient. Thus, the inclusion of cover crops is a sustainable solution to increase the ecosystem productivity, improve the soil fertility and oil yields. But, in Tunisia a few study were investigated the effect of legumes cover crop on the olive productivity. Therefore, the aim of this study was to evaluate the short-term (two cropping seasons s 2021 and 2022) effects of different seeded cover crops and soil management practices on the cover crops and soil characteristics, as well as enzymes activities and related microbial diversity. Six intercropping were tested in rainfed olive orchards (cv.Chétoui): Spontaneous vegetation (Spont), Wheat, Vetch, Oat, Fenugreek, mixture Vetch-Oat and compared to control (3 periodic tillage/year without intercropping). During the first cropping season, cover crops were cut as animal feed and only residues were incorporated into the soil. While, during the second year, all cover crops biomass were incorporated into the soil. Results indicate that the dry biomass and carbon uptake were significantly higher in grasses species (Wheat and Oat). But, highest level of nitrogen was found in Fenugreek cover crops. As compared to control, all cover crops including spontaneous vegetation increased soil organic matter and macronutrient level, mainly phosphorus. The most activity of β-glucosidase, phosphatase and arysulphatase was found in the cover crops plot of wheat and oat. In addition, this study improve that the utilization of the carbon sources was dominated by amides, amine and amino-acids in the fenugreek plot; while it was dominated by polymers and carboxylic acids in the case of wheat and oat.

Objectives: This paper presents a statistical review of modelling simulations for frequency and sensitivity of COVID-19 testing paradigms. Methods: We performed a review of preprints and published articles on PubMed from January 1, 2020 – March 1, 2021 using the search terms “COVID screening testing”, “COVID testing frequency”, “COVID testing frequency screening” and “SARS-CoV-2 testing frequency”.Results: Several authors’ conclusions support the claim that test frequency and test sensitivity both play a role in reducing SARS-CoV-2 transmission. We highlight the interplay between frequency of testing, test sensitivity and the speed at which test results are available in our review. Conclusions: Evidence suggests that sensitivity and frequency of testing both play a part in decreasing transmission of disease. We conclude that, overall, test sensitivity plays less of a role in reducing disease transmission in a population compared to the frequency of testing and how quickly test results are available.

Patients with a psychotic disorder frequently report oral health problems, while mental health nurses (MHNs) seem not to be fully aware of these problems and the risk factors. Therefore, this study aims to develop supportive tools for MHNs regarding oral health to increase sensitization among MHNs and to provide MHNs with knowledge to recognize (potential) oral health problems in patients with a psychotic disorder. We used a human-centered design in which the user, MHNs as well as experts by experience, were placed in the centre of the research process. Problems and needs in MHNs working with patients with a psychotic disorder were addressed. To identify key issues of problem as well as the needs in terms of resources, we started with focus groups (n = 9). We analysed the data thematically based on context of patients and MHNs in practice regarding oral health, preferred oral health tools focused on MHN, and intended outcomes of tools. A Multi Criteria Decision Matrix was developed and analysed (n = 9) to identify the most optimal and viable solution based on established criteria and issues that are prevalent in the work of MHNs. Most promising result was the development of a brochure with an awareness screener. The brochure with awareness screener was developed as a low-fidelity prototype for MHNs regarding oral health in patients with a psychotic disorder, based on the latest scientific evidence. After testing it, the feasibility was tested through semi-structured interviews (n=19). MHNs and experts by experience were satisfied with the tool and provided recommendations for adjustments to the content. Significant augmentations to the brochure include a clinical lesson and a toothbrush with toothpaste for patients. We can conclude that a brochure with an awareness screener is feasible for MHNs. Future steps aiming to further refine and optimize care processes for oral health tools in MHNs, should take refining eligibility criteria for psychiatric populations and the language level of the target group of a tool into account.

Land cover segmentation, a fundamental task within the domain of remote sensing, boasts a broad spectrum of application potential. In this article, we focus on the land cover segmentation tasks and complete the following research work: Firstly, to address the issues of uneven distribution of foreground and background and significant differences in target scales in remote sensing images, we propose a decoder called MDCFD based on multi-dilation rate convolution fusion. The decoder utilizes dilated convolution to expand the receptive field, enhancing the model's ability to capture global features and thus improving the model's ability to distinguish between foreground and background. Meanwhile, we design a multi-dilation rate convolution fusion module (MDCFM), which fuses the outputs of different dilation rate convolution layers. Secondly, aiming at the problems of diverse scenes, significant differences between categories, and many background interferences in remote sensing images, we propose a hybrid attention module called LKSHAM based on large kernel convolution. This module combines spatial attention and channel attention mechanisms and combines the two attention modules in series. By introducing large kernel convolution, the model's ability to extract contextual information is improved. At the same time, we adopt a strategy of decomposing large kernel convolution into multiple depthwise convolutions to reduce computational complexity. The improved network models designed by this paper can achieve an improvement of over 1.1% in the mIoU metric on segmentation tasks on the Potsdam and Vaihingen datasets.

Large-scale land cover plays a crucial role in global resource monitoring and management, as well as research on sustainable development. However, the complexity of the mapping process, coupled with significant computational and data storage requirements, often leads to delays between data processing and product publication, creating challenges for dynamic monitoring of large-scale land cover. Therefore, improving the efficiency of each stage in large-scale land cover mapping and automating the mapping process is currently an urgent and critical issue that needs to be addressed. We propose a high-performance automated large-scale land cover mapping framework(HALF) that introduces high-performance computing technology to the field of land cover production. HALF optimizes key processes, such as automated sample point extraction, sample-remote sensing image matching, and large-scale classification result mosaic and update. We selected several 10°×10° regions globally and the research makes several significant contributions:(1)We design HALF for land cover mapping based on docker and CWL-Airflow, which solves the heterogeneity of models between complex processes in land cover mapping and simplifies the model deployment process. By introducing workflow organization, this method achieves a high degree of decoupling between the production models of each stage and the overall process, enhancing the scalability of the framework. (2)HALF propose an automatic sample points method that generates a large number of samples by overlaying and analyzing multiple prior products, thus saving the cost of manual sample selection. Using high-performance computing technology improved the computational efficiency of sample-image matching and feature extraction phase, with 10 times faster than traditional matching methods.(3)HALF propose a high-performance classification result mosaic method based on the idea of grid division. By quickly establishing the spatial relationship between the image and the product and performing parallel computing, the efficiency of the mosaicking in large areas is significantly improved. The average processing time for a single image is around 6.5 seconds.

The application of machine learning techniques to satellite imagery has been the subject of interest in recent years. The increase in quality and quantity of images, made available by Earth observation programs, such as the Copernicus program, led to the generation of large amounts of data. Among the various applications of this data is the creation of land cover maps. The present work aimed to create machine learning models capable of accurately segment and classify satellite images, to automatically generate a land cover map of the Portuguese territory. Several experiments were carried out with the spectral bands of the Sentinel-2 satellite, with vegetation indices, and with several sets of land cover classes. Three machine learning architectures were evaluated, which adopt two different techniques for image classification. One of the classification techniques follows an object-oriented approach, and in this case the architecture adopted in our models was a U-Net artificial neural network. The other classification technique is pixel-oriented, and the machine learning models tested were random forest and support vector machine. The overall accuracy of the results obtained ranged from 68.6% to 94.75%, depending strongly on the number of classes into which the land cover is classified. The result of 94.75% was obtained when classifying the land cover only into 5 classes. However, a very interesting accuracy of 92.37% was achieved by the model when trained to classify 8 classes. These results are superior to those reported in the related bibliography.