Background: Removable prostheses have seen a fundamental change recently because of advances in polymer materials, allowing improved durability and performance. Despite these advancements, notable differences still occur amongst various polymer materials and processing technologies, requiring a thorough grasp of their mechanical, physical, and therapeutic implications. Methods: Fours different processing techniques, all utilizing Polymethyl methacrylate (PMMA) as the main material, were used to construct complete dentures. The specimens underwent a mechanical test. Results: All the specimens broke under the influence of a certain force, rather than yielding through flow, as is characteristic for plastic materials. For each specimen, the maximum force (N) was recorded (figure 4), as well as the breaking energy, Conclusions: The best results were obtained in the case of the thermoplastic injection system and, surprisingly and contrary to those in the specialized literature, the worst results were recorded in the case of 3D printed samples.

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement stabilized base. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement stabilized base. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement stabilized base composing of RCA and DS. The test results reveal that the performance of cement stabilized base with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfy the road use. Meanwhile, DS is beneficial to improve the strength of cement stabilized base. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement stabilized base. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering.

Glass and ceramics have a fundamental and crucial role in our lives due to their properties and aesthetic decoration. However, they create serious environmental problems, mainly due to their high occupation of landfills and harmful emissions. Both wastes could be utilized to reduce the natural resources' adverse environmental effects and exhaustion. With increasing environmental concerns to reduce solid waste as much as possible, the concrete industry has adopted several methods to achieve this goal. Hence this study examines the performance of self-compacted concrete (SCC) utilizing various percentages of recycled waste materials such as those deposited from glass and ceramic industries. The idea of utilizing recycled waste materials in concrete manufacturing has gained massive attention due to their impressive results in rheological and mechanical state. Recycled glass (RG) and ceramic waste powder (CWP) were utilized to replace fine aggregate and cement, respectively. Five mixes were designed, including the control mix, and the other four mixes with different dosages of RG and CWP as fine aggregate and cement replacement ranging between 5 to 25%. Mixes were tested for both rheological and mechanical properties to evaluate their compilment with SCC requirements as per codes and guidelines. The results revealed that 20%CWP or less as cement replacement and 10% or less of RG as fine aggregate replacement would provide suitable rheological properties along with mechanical ones. Utilizing recycled glass and ceramic waste powder provides strength like the mix designed with natural resources, which helps us structure economically and environmentally friendly.

In order to apply RAP fine aggregate to High Modulus Asphalt Concrete(HMAC), this study first extracts aged asphalt from RAP fine aggregate through extraction and distillation, and adds it to high modulus modified asphalt in proportions of 20%, 40%, 60%, and 80%. The performance changes of the recycled asphalt were investigated using conventional performance tests and dynamic shear rheological tests (DSR). Microscopic techniques such as four‐component analysis and infrared spectroscopy were employed to explain macroscopic performance changes in terms of component and functional group changes in the asphalt. Using HMAC‐20 gradation as an example, uniaxial compression dynamic modulus tests, rutting tests, freeze‐thaw splitting tests, and low‐temperature bending tests were conducted to evaluate the performance changes of recycled asphalt mixture with different RAP fine aggregate contents through four indices: dynamic modulus, dynamic stability, tensile strength ratio (TSR), and maximum bending strain. The results indicate that for every 20% increase in aged asphalt, the penetration at 25°C, ductility at 25°C, and dynamic viscosity at 60°C decrease by approximately 6.2%, 15.4%, and 3.9%, respectively, while the softening point increases by approximately 13.3%. It is concluded that the addition of aged asphalt significantly affects the ductility at 25°C and the softening point. As the aged content increases, the complex shear modulus (G*) and phase angle (δ) of the recycled asphalt decrease, while the rutting factor increases. The four‐component analysis and infrared spectroscopy of the asphalt demonstrate that the incorporation of aged asphalt is merely a physical blending phenomenon, involving changes in the content of the four components without the formation of new functional groups (new peaks). When RAP fine aggregate is applied to high modulus recycled asphalt mixture, compared to high modulus modified asphalt mixture, the recycled mixtures exhibit higher dynamic modulus and dynamic stability, but significantly reduced water stability and low‐temperature performance.

Spinocerebellar ataxia type 3 is a neurodegenerative disease caused by an abnormal expansion of CAG repeats in the disease gene ATXN3, leading to prolonged polyglutamine (polyQ) tracts in the respective protein ataxin-3. The polyQ-expanded protein forms polyQ-containing aggregates in several brain regions which leads to neuronal cell loss. Autophagy is thought to play a significant role in clearing these polyQ-containing protein aggregates. Therefore, the autophagy mechanism was investigated in SCA3 with focus on the autophagic protein p62/sequestosome-1. Human and mouse RNA sequencing data were analyzed to determine RNA expression level of autophagic genes. Additionally, autophagy was studied in the SCA3 304Q knock-in mouse model and through several cell culture experiments using HEK-293T cells transfected with ATXN3 of differ-ent polyQ lengths. For cell culture experiments, autophagy was induced with rapamycin treat-ment, proteasomal degradation was blocked with MG132 and degradation of autophagic pro-teins was investigated using cycloheximide treatment. Here, we report an increased autophagy impairment with SCA3 disease progression seen in HEK-293T cells transfected with ATXN3 plasmid with expanded polyQ tracts, higher aged 304Q-knock-in mice, or human post-mortem brain material. Furthermore, co-localized aggregation of the autophagic protein p62 and the dis-ease protein ATXN3 was observed in the course of SCA3 disease. Therefore, we suggest a signifi-cant role for p62 in aggregate formation seen in the neurodegenerative disease SCA3.

Technological equipment in quarries that extract and deliver aggregates for different uses operates in a predetermined flow depending on the type of rocks exploited and the dimensional characteristics imposed on the final products. In this context, the interruptions in operation required to replace high-wear parts (such as the teeth of excavators and bucket loaders) must be limited as much as possible through technological solutions to increase their service life. The evolution of the wear of the teeth of the quarry equipment that come into direct contact with the rocks was concretely established in the production process, in parallel with the wear values obtained by simulating the wear phenomenon in laboratory conditions, in order to validate the data collected during the operation of the machines. Preventive-repetitive maintenance, within the activities of reconditioning the worn surfaces of the teeth, through the charging process by manual electric welding with covered electrodes, was applied directly to the machine, which led to the shortening of the interruptions in operation necessary to replace these spare parts.

In order to study the effect of explosion load on the flexural performance of RC beams, two RC beams of the same size were carried out explosion test and bearing capacity test successively. Piezoelectric intelligent aggregate was embedded in the beams in advance to monitor the damage state of the beams, which realized the whole process of damage monitoring of the concrete inside the structure from explosion damage to compression damage.Based on wavelet packet analysis and residual bearing capacity damage evaluation criteria, the beam damage was quantitatively evaluated, and the bending bearing capacity of RC beam after explosion damage was compared and analyzed.The results show that the change of concrete strain gauge signal, the phenomenon of crack development and the increase of internal crack development index indicate that the RC beam is damaged by explosion load.After explosion damage, the damage index of the beam increases and the residual bending capacity decreases, which proves that the piezoelectric intelligent aggregate sensor can effectively monitor the bending capacity change of the component after explosion damage.

Traditional concrete pavements have poor water permeability, while the strength of pervious concrete pavements is low. To solve these problems, this study designed Innovative recycled aggregate pervious concrete (I-RAPC) with controllable water permeability and high strength by using response surface methodology, and investigated the effects of different pore parameters (number, diameter, material, distribution form, etc.) on the performance of I-RAPC. And the strength discount factor method was proposed to construct the theoretical calculation model of compressive strength and pipe pore parameters, and the calculation model of water permeability coefficient was established at the same time. The results show that the fewer the number of holes and the smaller the pipe diameter of I-RAPC, the higher its compressive strength and the smaller the water permeability coefficient. The theoretical model of compressive strength can accurately evaluate the discounting effect of the pore parameters on the compressive strength of I-RAPC, and the maximum relative error is only 7.52%, and the maximum relative error of the calculation model of water permeability coefficient is only 4.42%. I-RAPC has the advantages of high strength and permeability with controllable performance, which overcomes the problems of random distribution of pore space, uncertainty of water permeability, and strength of ordinary pervious concrete.

Amidst increasing awareness of diet-health relationships, plant-derived bioactive peptides are recognized for their dual nutritional and health benefits. This study investigates bioactive peptides released after Alcalase hydrolysis of protein from chachafruto (Erythrina edulis), a nutrient-rich South American leguminous plant, focusing on their behavior during simulated gastrointestinal digestion. Evaluating their ability to scavenge radicals, mitigate oxidative stress, and influence immune response biomarkers, the study underscores the importance of understanding peptide interactions in digestion. Methods included previous enzymatic hydrolysis with Alcalase to obtain peptides, and results show significant radical scavenging and oxidative stress protection by chachafruto peptides. These findings highlight the potential of chachafruto bioactive peptides in functional foods and nutraceuticals, supporting human health through dietary interventions.

This paper describes the proposal and development of a proof of concept (PoC) for a data logger system designed for operation and fault detection in bench testing of combustion engines. The main objective was to develop a data logger system that collects data on vibration, sound, temperature, and CO2 levels to identify ignition and combustion faults, thereby contributing to reducing greenhouse gas emissions (GHG). The paper presents (i) the proposal and development and (ii) the open-source code: proof of concept for a data logger system focused on detecting faults and monitoring the operational condition of benchtop combustion engines. The results indicate the feasibility of the PoC for data acquisition and dataset creation for Research and Development purposes.

The slate aggregate has long been perceived as a substandard, low quality waste material with its physical and chemical properties not being competitive with those of the primary aggregates. It is assumed that the slate aggregate particles are not strong, that is not durable and will not compact. This research aims to address those claims and review the available literature on the performance of the slate aggregate. The review inaugurates by analysing the physical, chemical and mechanical properties of slate, before expanding into a literature review of laboratory testing’s on the effect of moisture content on density, compaction and layer thickness of slate aggregate.The paper reviews case studies of construction projects in North Wales, where the slate aggregate has been used for general fill and road building for many years. Some of the case studies include the A55 coastal road and duelling of the A5 in Anglesey (WRAP, 2004), where slate aggregate was successfully used as sub-base. The paper also investigates why many civil engineers are reluctant to use the slate aggregate and regard the material as sub-standard, flaky aggregate. The research paper reviews the potential usages and various products the slate aggregate is suitable for and satisfies the requested standards. The final topic reviewed is the cost of transporting slate aggregate compared with the cost of transport for primary aggregate and the introduction of the Primary Aggregates Tax (Parliament of the United Kingdom, 2011). The last topic includes a critical analyses of the claims that the slate aggregate a commercially viable construction material despite its remote location (Woodward et al, 2004). The transportation cost and the supply chain complexities must be evaluated prior to considering the long-term sustainability of the product (Radanliev et al^1-6, 2014, 2015, 2016).

Seedling establishment is often a critical bottleneck to revegetation of mine tailings and similar substrates with a low capacity to retain water and plant nutrients. Biochar and deactivated yeast are potential sustainable, low-cost materials with high nutrient- and water-holding capacity that could be used in this context as seed coatings to aid in seedling establishment on challenging sub-strates. We conducted a greenhouse study to assess the effectiveness of biochar and deactivated yeast, applied alone in a factorial combination, as seed coatings, on the germination, establish-ment, and early growth of white clover (Trifolium repens) and purple prairie clover (Dalea pur-purea). Coated seeds were applied to a mine tailing, a coarse granitic sand, and potting soil mix substates; seedling establishment and growth were monitored over 75 days. Results indicate strong interactive effects of seed coatings with species and substrate. Biochar coatings enhanced seedling establishment of Trifolium, with biochar or biochar plus yeast coatings giving the best results. In some cases, these effects persisted throughout the experiment: biochar coatings resulted in a ~5-fold increase in Trifolium biomass at harvest for plants in the potting soil mix but had neutral effects on sand or tailings. Biochar seed coatings also enhanced Dalea germination in some cases, but benefits did not persist. Our results indicate that biochar-based seed coatings can have lasting effects on plant growth well beyond germination, but also emphasize highly spe-cies-specific responses that highlight the need for further study of broader patterns and mecha-nisms.

Solid waste management is a major environmental challenge, especially in developing countries, with increasing amounts of waste glass (WG) and waste plastics (WP) not being recycled. In Ethiopia, managing WG and WP requires innovative recycling techniques. This study examines concrete properties with WG and WP as partial replacements for fine aggregate. Tests were conducted on cement setting time, workability, compressive strength, splitting tensile strength, and flexural strength. Concrete grade C-25, with a compressive strength of 25 MPa, was prepared using an optimum ratio of 14% WG and 6% WP. Mechanical properties were tested at 7 and 28 days of curing. At 20% replacement, workability decreased at water-cement ratios of 0.5 and 0.6 but remained stable at 0.4. Thus, a 0.4 ratio was used. For 10% replacement, compressive strength increased by 12.55% and 6.44% on the 7th and 28th days, respectively. At 20% replacement, compressive strength decreased by 14.35% and 0.73% on the 7th and 28th days, respectively. On the 28th day, splitting tensile strength at optimum replacement was 4.3 MPa, an 8.5% reduction from the control mix. However, flexural strength increased by 19.7%, from 12.46 MPa to 15.52 MPa. Overall, WG and WP improved flexural strength but slightly reduced splitting tensile strength.

The use of alternative fuels and electric vehicles is an opportunity to reducing exhaust emissions. We observe that the regulations on exhaust emissions from mobile sources are becoming gradually stricter on the all the world. As is widely known, using alternative fuels instead of conventional fuels helps lower vehicle emissions. The most popular alternative fuels are hydrogen, propane, biobutanol, methanol, dimethyl ether, etc. It is very important that more than a dozen alternative fuels are under development. The article contains a comparison of the operating costs of electric cars and cars with an internal combustion engine. This work shows also the characteristic of new alternative fuels and their impacts on exhaust emissions.

The global food production system faces several challenges, including significant environmental impacts due to traditional agricultural practices. The rising demands of consumers for food products that are safe, healthy, and have animal welfare standards have led to an increased interest in alternative proteins and the development of the cellular agriculture field. Within this innovative field, precision fermentation emerges as a promising technological solution to produce proteins with reduced ecological footprints. This review provides a summary of the environmental impacts related to the current global food production, and explore how precision fermentation can contribute to address these issues. Additionally, we will report on the main animal-derived proteins produced by precision fermentation, with a particular focus on those used in the food and nutraceutical industries. The general principles of precision fermentation will be explained, including strain and bioprocess optimization. Examples of efficient recombinant protein production by bacteria and yeasts, such as milk proteins, egg-white proteins, structural and flavoring proteins, will also be addressed, along with case examples of companies producing these recombinant proteins in a commercial scale. Through these examples, we will explore how precision fermentation supports sustainable food production and holds the potential for significant innovations in the sector.

This study investigates the necessity of particle asymmetry for self-propulsion in nanomotors. While conventional wisdom posits that asymmetric designs are crucial for generating phoretic forces or localized bubble propulsion, recent research suggests that symmetrical particles may also exhibit motility. To address this debate, we developed a robust workflow for synthesizing gold grafted silica nanoparticles with precise control over size and shape, enabling the direct comparison of their motile behavior by dynamic light scattering and particle tracking velocimetry. Our results indicate that the inherent asymmetry generated during isotropic gold nanoparticle deposition onto silica surfaces may enable particle motility.

In this review we aim to address the current status of phage therapy in the management of multidrug-resistant infections, from compassionate use cases to ongoing clinical trials, as well as the challenges this approach presents in the particular context of CF patients.

Microbes have evolved many fascinating and complex ways of interacting with conspecifics. Perhaps one of the most interesting is aggregative multicellularity, wherein independent cells come together and adhere to one another in order to form a larger entity. The fundamental benefits of active aggregation into multicellular groups generally remain unclear, and there are many open questions about what selective pressures led to the evolution of this behavior in various eukaryotic and prokaryotic taxa, most notably the dictyostelids and the myxobacteria. Aggregative multicellularity can be partitioned into three main phases: coming together, staying together as a group, and disaggregation. Different selective pressures may have led to adaptations unique to each phase. While aggregative microbial systems generally form elevated multicellular structures such as fruiting bodies, these can vary in complexity and morphology even among closely related species. What evolutionary forces shaped such morphological diversification remains unknown. Strains that are not genetically identical can coaggregate, which can impact group-level function either positively through functional synergy or negatively through harmful exploitation. Such chimerism within aggregates is likely to have played important roles in shaping the evolution of microbial multicellularity. Much further research is needed into the evolutionary forces and processes leading to and shaping the many forms of microbial aggregation.

Background: Complementary and alternative medicines (CAM) are widely used, with pharmacies accounting for a significant share of the distribution market. Despite their popularity, many CAMs lack scientific evidence for effectiveness, and some can cause adverse health effects. Limited research exists on CAM-related adverse events and the effectiveness of CAM labels in conveying crucial information. Methods: This cross-sectional study aimed to investigate CAM utilization, consumer perspectives, and the influence of labels on CAM usage in Melbourne, Australia. Data were collected through an online questionnaire and analysed using descriptive statistics, Pearson's correlation, MANOVA, and regression analyses. Results: The study enrolled 125 current CAM users, primarily recruited from pharmacy and supermarket customers (age: predominantly 31-50; gender: 20.8% male, 79.2% female). Participants' perceptions of effectiveness and safety were positively correlated. Label warnings prompted information-seeking, but consultation with healthcare professionals (HCPs), particularly pharmacists, was infrequent (24%). Adverse reactions were reported by 18.5% of participants, with 8.3% experiencing severe reactions. The analysis revealed relationships between CAM usage and demographics. Ordinal logistic regression showed a significant association between calcium consumption and higher age groups (coefficient = 1.658, p = 0.006), while binary logistic regression identified higher iron consumption among females (coefficient = 2.177, p = 0.007). Conclusions: Label warnings significantly prompted consumers to seek more information about CAMs. However, a limited engagement of HCPs, especially pharmacists, suggests an opportunity for improved consumer education and pharmacist involvement in CAMs-related discussions. The findings highlight demographic influences on CAM usage being essential for developing targeted health interventions and policies. Addressing these aspects may lead to safer CAM practices and informed consumer decision-making.

Vitamin A, or retinol, is one of the most effective anti-ageing molecules, but it presents issues with photo-sensitivity and irritation. Retinol-like alternatives are emerging, but have so far been less effective. Here, we present a Silibum marianum extract (SME) as a retinol-like ingredient providing both safety and efficacy. SME was compared to the reference compound, retinol, and to the main alternative, bakuchiol. In ex vivo tests, skin explants from a 58-year-old donor were treated with pure retinol (0.1%), bakuchiol (0.2%) or SME (0.8%). After 5 days, collagen and hyaluronic acid levels were analysed. A placebo-controlled study involving 57 volunteers (ages 45-73 years) was also conducted, with products applied twice-daily for 56 days. Results were measured by AEVA-HE and VISA. Levels of collagen III were significantly increased by SME, by 23% and 16% compared to bakuchiol and retinol, respectively. Compared to bakuchiol, SME treatment increased hyaluronic acid production by 36%. In clinical tests, SME had a significantly stronger anti-wrinkle effect than bakuchiol – reducing the number of wrinkles on the forehead by 21%, and their circumference by 17% – producing effects similar to retinol, and better than bakuchiol. In the self-assessment, 43% of volunteers reported discomfort while using retinol, as compared to 0% for the SME formulation. By enhancing levels of collagen III – the youth collagen – and hyaluronic acid in the skin, SME paves the way for the maturation of collagen I fibrils and skin plumping. With its stronger efficacy compared to bakuchiol and enhanced safety profile compared to retinol, SME may be the next-generation of natural alternatives to retinoids.

Hydrogen has a leading role in accomplishing a net zero green-house gas emission future. Today’s challenge is producing green hydrogen to cover the fuel demand of transportation and industry, to gain independence from fossil fuels. This review’s goal is to demonstrate critically the existing methods of biomass treatment and assess their ability to scale up. Biomass is an excellent hydrogen carrier and biomass-derived processes are the main target for hydrogen production as it is an innovative pathway to green hydrogen production. Comparing the existing processes, thermochemical treatment is found to be far more evolved than biological or electrochemical treatment especially with regard to scaling prospects.

This article provides a detailed analysis of non-invasive techniques for prediction and diagnosis of faults in internal combustion engines, focusing on the application of the Proknow-C and Methodi Ordinatio systematic review methods. Initially, the relevance of these techniques in promoting energy sustainability and mitigating greenhouse gas emissions is discussed, aligning with the Sustainable Development Goals (SDGs) of Agenda 2030 and the Paris Agreement. The systematic review conducted in the subsequent sections offers a comprehensive mapping of the state-of-the-art, highlighting the effectiveness of combining these methods in categorizing and systematizing relevant scientific literature. The results reveal significant advancements in the use of artificial intelligence (AI) and digital signal processors (DSP) to enhance fault diagnosis, as well as underscore the crucial role of non-invasive techniques in minimizing interference in monitored systems. Finally, concluding remarks point towards future research directions, emphasizing the need to develop digital twins for internal combustion engines and identify gaps for further improvements in fault diagnosis and prediction techniques.

Additives for anaerobic digestion (AD) can play a significant role in optimising the process by increasing biogas production, stabilising the system and improving digestate quality. The role of additives largely boils down to: (i) enhancing direct interspecies electron transfer (DIET) between microbial communities, resulting in improved syntrophic interactions and methane production rates (e.g. biochar, magnetite and carbon nanotubes), (ii) adsorption of toxic substances that may inhibit microbial activity (e.g. activated carbon, zeolites), (iii) improving microbial activity and increasing process stability (e.g. cobalt, nickel, iron, selenium), (iv) maintaining optimal pH levels for microbial activity (e.g. magnesium oxide), (v) reducing inhibition (the aforementioned adsorbents and conductive substances), (vi) accelerating the decomposition of complex organic materials into simpler compounds that are more easily digested by microorganisms, thereby increasing the rate of hydrolysis (enzymes, including cellulases, proteases and lipases). Through the aforementioned action, additives can significantly affect AD performance. The function of these materials varies, from enhancing microbial activity to maintaining optimal conditions and protecting the system from inhibitors. The choice of additives should be carefully tailored to the specific needs and conditions of the digester to maximise benefits and ensure sustainability. In light of these considerations, this paper characterizes the most commonly used additives and their combinations based on a comprehensive review of recent scientific publications, including a report on the results of conducted studies. The publication features chapters that describe: carbon-based conductive materials, metal oxide nanomaterials, trace metal and biological additives, including enzymes and microorganisms. It concludes with a chapter summarising reports on various additives and discussing their indications for functional systems with determined properties. A notable advantage of this work is the updated literature data, clear summaries, and a substantive description of the performance of the additives discussed.

The energy supply for isolated systems remains a current challenge in Brazil and worldwide, particularly when known solutions are compared regarding cost, the ability to supply energy on demand, and sustainability. In this context, green hydrogen, which has been considered one of the main paths for the decarbonization of the energy chain, is also seen as a potential solution for energy supply in isolated systems. Based on a literature review of articles addressing the topics of green hydrogen and isolated systems, an analysis is conducted on the application of green hydrogen as an energy supply solution for isolated systems. The review identified and collected data on important parameters for comparing solutions, such as CAPEX, OPEX, energy cost, and the price per kilogram of hydrogen. Using these data, analyses were performed to provide an overview of the application of green hydrogen in isolated systems. One of the objectives of this work is to present a comprehensive analysis of the green hydrogen chain and its application in the context of electricity generation, particularly for isolated systems in Brazil.

Lynch syndrome (LS) is one of the most common hereditary cancer syndrome in human populations, associated with germline variants in MLH1, MSH2/EPCAM, MSH6 and PMS2 genes. The advent of next generation sequencing has proven a significant impact in germline variant detection in the causative genes; however, a large proportion of patients with clinical criteria still receive uncertain or negative results. PMS2 is the least frequent reported gene, associated with up to 15% of LS cases with late-onset disease and low penetrance phenotype; however, the proportion of PMS2-LS cases is considered to be highly underestimated. In this context, we consulted public available databases (ClinVar, LOVD) for missense and intronic PMS2 variants and performed an in silico analysis of the genomic sequence. Splicing bioinformatics tools proven effective in other genes were used to assess both the wild-type DNA sequence and reported genetic variants. Splicing alterations were predicted in silico and using GTEx short-read RNA expression data. Out of the 2384 missense variants discovered, 90% were classified with uncertain significance (VUS). 4.9% of missense variants were shown to have a potential splicing consequence (DS > 0.2) using SpliceAI. As described in the original publication, SpliceAI-visual was proven effective in annotation of short intronic variants (< 50 bp). Four short intronic variants were identified using SpliceAI-visual as potentially splicing disturbing, in spite of using a lower threshold (DS > 0.1). Moreover, we observed that Splicing Regulatory Elements (SREs) may play a fundamental role in alternative splicing in PMS2 gene, ESE motifs being overrepresented in highly expressed exons 5, 11 and 14. Computational analysis performed in our study serves as a valuable filtering step for guiding further RNA sequencing experiments. Additional functional data is necessary to evaluate the significance of our findings.

Autism spectrum disorder (ASD) is a neurodevelopmental condition marked by re-stricted and repetitive behaviors as well as difficulties with social interaction. Nu-merous studies have revealed aberrant lipid mediators and autoimmunity as a recog-nized etiological cause of ASD that is amenable to therapeutic intervention. Methods: In this study, the relationship between the relative cyclooxygenase-2, / pros-taglandin E2 ratio (COX-2/PGE2) as lipid mediator marker and anti-nucleosome au-toantibodies as autoimmunity marker of ASD was investigated using multiple regres-sion and combined receiver operating characteristic (ROC) curve analyses. The study also sought to identify the linear combination of these variables that optimizes the partial area under the ROC curves. There were forty ASD children and forty age- and sex-matched controls included in the current study. Results: Using combined ROC curve analysis, a notable increase in the area under the curve was seen. Additionally, it was reported that the combined markers had improved specificity and sensitivity. Conclusions: This study shows that using a ROC curve analysis to measure the predictive value of specific biomarkers linked to lipid metabolism and autoimmunity in children with ASD should improve our understanding of the etiological mechanism of ASD and how it is related to metabolism. Early diagnosis and intervention may be facilitated by this knowledge.

Keywords: Vascular Malformation, Diode Laser, Angioma, Blue light, Conservative

This study aimed to compare the differences in durability and prestress loss between normal-weight concrete (NC) and lightweight aggregate concrete (LWC) prestressed box girders, which were constructed at the same time in the same area, so as to verify the superiority of using synthetic lightweight aggregate (LWA) made from reservoir sediments in prestressed bridges. For the NCs and LWCs used in prestressed box girders, the basic mechanical properties were tested on the one hand, and the durability properties were tested on the other hand. Then, through the prestress monitoring system, the prestress loss of the two groups of the prestressed box girders was tracked. The results of the durability test confirmed that LWC can inhibit the penetration of air, water, and chloride ions by strengthening the interfacial transition zone between the aggregate and the cement paste, thereby improving its durability. Moreover, the magnetic flux prestress loss of the NC prestressed box girder reached 8.1%. In contrast, the magnetic flux prestress losses on both sides of the LWC prestressed box girder were 4.6% and 4.9%, respectively. This verified that, under the same environmental conditions, the use of LWC produced less of a prestress loss than the use of NC.

The performance of recycled aggregate concrete deteriorates due to the defects of adhesive mortar, pores and cracks on the surface of recycled aggregate. It is of great engineering significance to modify the reclaimed aggregate to improve its performance and adaptability. In this paper, the physical and chemical properties of waste concrete recycled aggregate are reviewed. Then, the existing modification methods and technologies of recycled aggregate, including physical, chemical and biological methods, are reviewed. Finally, the existing problems of the current modification technology are summarized, and the future research direction is proposed. It is expected to provide a new idea and method for the modification of waste concrete recycled aggregate.

In the modern construction industry, lightweight aggregate concrete (LWAC) is often used in the production of load-bearing structural members. LWAC can be up to 40% lighter by volume in comparison to normal strength concrete. On the other hand, the lack of adequate numerical models often limits the practical application of innovative building materials, such as lightweight concrete, in real projects. This trend is due to the uncertainties in design standard methods and calculation errors, the level of which is generally unacceptable to civil engineers in terms of safety and reliability. In the present paper, a comparative numerical deformation analysis of a full-scale bridge deck slab and girder has been carried out. Using the physical model proposed by the authors and the finite element software ATENA, the deformations of full–scale lightweight and traditional reinforced concrete elements under short-term effects of permanent and variable loads was compared. Depending on the safety and serviceability limit requirements, it was found that the amount of longitudinal reinforcement in lightweight reinforced concrete elements can be reduced compared to normal reinforced concrete elements with the same parameters. The results of the numerical analysis show that the deformation analysis model proposed by the authors can be a reliable tool for the design of lightweight concrete flexural members by selecting the optimum geometrical and reinforcement parameters limited by the stiffness condition.

In the present trend of constructing taller and longer structures, the application of lightweight aggregate concrete is becoming an increasing important advanced solution in the modern construction industry. In engineering practice, the analysis of lightweight concrete elements is performed using the same algorithms used for normal concrete elements. As an alternative to traditional engineering methods, nonlinear numerical algorithms based on constitutive material models may be used. The paper presents a comparative analysis of curvature calculations for flexural lightweight concrete elements, incorporating analytical code methods EN 1992-1 and ACI 318-14, as well as a numerical analysis using the constitutive model of cracked tensile lightweight concrete recently proposed by the authors. To evaluate the adequacy of the theoretical predictions, experimental data of 51 lightweight concrete beams tested during five different programmes were collected. A comparison of theoretical and experimental results showed that the most accurate predictions are obtained using numerical analysis and the constitutive model proposed by the authors. In the future, the latter algorithm can be used as a reliable tool for improving the design standard methods or numerical modelling of lightweight concrete elements subjected to short-term loading.

Today, the style of light construction materials used in building is one of the most important factors in reducing building's dead load and better performance of the structures in the earthquake. One of the ways to reduce the structure weight is to use lightweight blocks instead of using traditional materials. The main purpose of this research is to compare density, compressive strength and water absorption volume of non-load-bearing lightweight blocks made of natural and artificial lightweight aggregates. Scoria lightweight aggregates of Sanandaj, Ghorveh mine, pumice in Tabriz, Bostanabad mine, and Leca in Leca enterprise have been used to make the samples. Given the importance of the materials used, grading of coarse-grained materials has been conducted based on the standard of 7657 and grading of fine materials have been conducted based on the standard of 302.The experiments' results show that Scoria blocks due to hard texture, and high mechanical resistance of their lightweight aggregates, have had higher compressive strength, and density and lower water absorption volume compared to pumice and Lika lightweight aggregate blocks. Pumice blocks despite having desirable compressive strength and lower density compared to the two other blocks have higher water absorption volume, and do not meet the standard conditions. This same factor causes it faces with less interest. Among these Lika blocks with density of 1151.94 (kg per cubic meter) below 2000 kilograms per cubic meter of Iran density standard of 7782 (28-day compressive strength of 2.57 MPa), higher than 2.5 MPa of Iran compressive strength standard of 7782 (and water absorption volume of 282.92 kg per cubic meter) below 288 kilograms per cubic meter of Iran water absorption volume standard of 7782 (as a non-load-bearing lightweight block) have been diagnosed desirable.

In the past years, consumers have increased their interest to buy healthier food products, rejecting those products with more additives and giving preference to the fresh ones. Moreover, the current environmental situation has made society more aware of the importance of reducing the production of plastic and food waste. In this way and considering the Food Industry need of reducing the food spoilage along the food chain, edible coating has been considered as an eco-friendly food packaging that can replace traditional plastic packaging providing an improvement in the product’s shelf-life. Edible coating are thin layers applied straightaway on the food materials’ surface, that are made of biopolymers that usually incorporate other elements, such as nanoparticles or essential oils, to improve their physicochemical properties. These materials must provide a barrier that can prevent the pass of water vapor and other gasses, the microbial growth, the moisture loss, and the oxidation, so the shelf-life could be extended. The aim of this review was to compile the current data available to give a global vision of the formulation process and the different ways to improve the characteristics of the coats applied in both fruits and vegetables. In this way, the suitability of compounds in by-products produced during the Food Industry chain were also considered for the edible coating production.

The p53 tumor suppressor protein is an activator of transcription. Diverse stress factors lead to various sets of posttranslational modifications of p53 what results in different sets of upregulat-ed genes. We noticed that actinomycin D and nutlin-3a (A+N) synergize in inducing activating phosphorylations of p53 and upregulation of selected p53-target genes. Here we found that one of these genes is DUSP13, which codes for poorly-studied, dual-specificity phosphatase having at least two isoforms, one expressed in testis and the other in skeletal muscles. In cancer cells ex-posed to A+N, DUSP13 is expressed from an alternative promoter in intron, what results in ex-pression of isoform named TMDP-L1. The luciferase reporter tests demonstrated that this pro-moter is activated by both endogenous and ectopically expressed p53. We showed for the first time that mRNA expressed from this promoter actually produces the protein, which can be de-tected by Western blotting in all examined cancer cell lines with wild-type p53 exposed to A+N. In some cell lines it is also induced by clinically relevant camptothecin or by nutlin-3a acting alone. This isoform, fused with green fluorescent protein localizes in perinuclear region of cells. Thus, TMDP-L1 isoform may be an important element of p53-regulated stress response system.

This study presents the chemical synthesis, purification, and characterization of a novel non-natural synthetic amino acid. The compound was synthesized in solution, purified, and characterized using NMR spectroscopy, polarimetry, and melting point determination. Dynamic Light 22 Scattering (DLS) analysis demonstrated its ability to form aggregates with an average size of 391 nm, extending to low micrometric sizes. Furthermore, cellular biological assays revealed its ability to enhance fibroblast cell growth, highlighting its potential for tissue regenerative applications. Circular dichroism (CD) spectroscopy showed the ability of the synthetic amino acid to bind serum albumins (using bovine serum albumin (BSA) as a model), and CD deconvolution provided insights into the changes in secondary structures of BSA upon interaction with the amino acid ligand. Additionally, molecular docking using HDOCK software elucidated the most likely binding mode of the ligand inside the BSA structure. We also performed in silico oligomerization of the synthetic compound in order to obtain a model of aggregate to investigate computationally. More in detail, in the dimer formation achieved by molecular self-docking, two distinct poses were observed, corresponding to the lowest and comparable energies, with one pose exhibiting a quasi-coplanar arrangement characterized by a close alignment of two aromatic rings from the synthetic amino acids within the dimer, suggesting the presence of π-π stacking interactions. In contrast, the second pose displayed a non-coplanar configuration, with the aromatic rings oriented in a staggered arrangement, indicating distinct modes of interaction. Both poses were further utilized in the self-docking procedure. Notably, iterative molecular docking of amino acid structures resulted in the formation of higher-order aggregates, with a model of a 512-mer aggregate obtained through self-docking procedures. This model of aggregate presented a cavity capable of hosting therapeutic cargoes and biomolecules, rendering it a potential scaffold for cell adhesion and growth in tissue regenerative applications. Overall, our findings highlight the potential of this synthetic amino acid for tissue regenerative therapeutics and provide valuable insights into its molecular interactions and aggregation behavior.

Using desi-cow waste products like Jeevamrit, natural farming is widespread among farmers for improving soil biology and productivity. Jeevamrit enhances soil chemical and microbiological properties without needing large quantities of farmyard manure (FYM), as a sustainable farming practice with a reduced carbon footprint. Despite its traditional use, Jeevamrit faces criticism due to a lack of scientific evidence. This study investigated the comparative effect of Jeevamrit and chemical fertilizers on the growth and yield of marigold cv. Siracole. In this study mother block of marigold was raised for both summer and winter seasons. The cuttings were harvested from the mother block and then kept for rooting. The rooted cuttings were planted at monthly intervals and evaluated for flowering parameters and compared to those treated with RDF (30:20:20 N, P, and K g/m2). Soil supplied with Jeevamrit enhanced bacteria (26.33%), fungi (18.92%), and actinomycetes (31.21%) populations compared over the recommended dose of fertilizers (RDF) (i.e. N:P: K @ 30:20:20 g m-2). Jeevamrit-treated plants have marketable flower yield per square meter (3.98 %) and shelf life (9.93 %) compared to RDF. The study concludes that Jeevamrit @ 2 liter m-2 is a sustainable and effective alternative to traditional fertilizers for enhancing marigold production in the mid-hills of the Himalayan region, where natural farming is already accepted.

The use of chemical pesticides in agriculture contributes to soil, water and air pollution, biodiversity loss and can harm non-target species. The European Commission has already established a Harmonized Risk Indicator to quantify the progress in reducing the risks linked to pesticides. Therefore, there is an increasing need to promote biopesticides or so-called low-risk pesticides (LRP). Extract from Melaleuca alternifolia – tea tree oil (TTO) is known for its antiseptic, antimicrobial, antiviral, antifungal, and anti-inflammatory properties. Tea tree oil has been extensively studied in pest management as well as in the pharmaceutical and cosmetic industry and there are already products based on its active substances on the market. This review focuses on the overall evaluation of tea tree oil in terms of effectiveness and safety as a biopesticide for the first time. The collected data can be an added value for further evaluation of tea tree oil in terms of the authorization extension as a fungicide in 2026.

This research investigates the fatigue behaviour and fracture mechanics of high-performance concrete (HPC), including various compositions such as HPC with basalt aggregates (HPC-B), HPC with gravel (HPC-G), and high-strength coarse mortar (CM) static and cyclic tensile loading within the special priority program SPP 2020. The study aims to integrate fracture mechanics into structural analysis to enhance design guidelines for slender cross-sections and safety-related high-performance structural components. The experimental investigations reveal HPC-B's re-markable superiority, displaying higher compressive strength, modulus of elasticity, and tensile strength compared to HPC-G and CM. A modified disk-shaped compact tension (MDCT) based on ASTM standards, aided by digital image correlation (DIC) unveils fracture behaviour, empha-sizing fracture energy as a crucial parameter. HPC-B exhibits improved crack resistance and notch sensitivity reduction attributed to crushed basalt aggregates and enhanced interfacial transition zone (ITZ). The research scrutinizes factors like material characterization, aggregate morphology, stress levels, and displacement rate on crack formation. High-cycle fatigue tests show HPC-B's superior performance, and post-fatigue analysis reveals enhanced residual fracture toughness attributed to nano-level structural changes, stress redistribution and aggregate-matrix interac-tion. 3D image analysis via Computed Tomography (CT) scans captures mesostructural crack propagation and provide quantitative insights. This study advances the understanding of HPC fatigue behaviour, emphasizing the interplay of aggregate types, morphologies, and their dy-namic response to cyclic loading, offering valuable insights for optimizing design guidelines and fostering innovation in structural engineering.

A viable radiation dominated era in the early universe is best described by the standard (FLRW) model of cosmology. In this short review, we demonstrate reconstruction of the forms of F(R) in the modified theory of gravity, and the metric compatible F(T) together with the symmetric F(Q) in alternative teleparallel theories of gravity from different perspectives, primarily rendering emphasis on a viable FLRW radiation era. Inflation has also been studied for a particular choice of the scalar potential. The inflationary parameters are found to agree appreciably with the recently released observational data.

CD44 glycoprotein is ubiqutously present and situated at the extracellular surface of cell. Its role as an adhesion recptor was modified depending upon the state of post addition of glycomoeties under varied microenvironment. Many alternative spliced variants of CD44 were expressed by human cells depending upon the attainment during mutifunctional signal disposition. The function of splice factors, and hnRNPA family (Heterogenous ribonucleoproteins A) were dicussed in context to CD44 alternative variants. Glioma cell cline U87 MG were used in this study to search more about the affect of hnRNPA1 and hnRNPA2/B1 knockdown in CD44 V6 and CD44V10 expression. We found in preliminary study that splice factor knock down reduces the alternative splice variants of CD44 such as V6 & V10. Therefore, potential of this study to elaborate further the mechanism in vivo model, to validate the alternative spliced variant in context to interaction with extracellular microenvironment.

Endo-reticular stress induces the unfolded protein response including a highly conserved set of genes crucial for cell survival against a variety of onslaughts. Among the activated stress response genes is Ire1, which undergoes auto-phosphorylation and acquires a regulated Ire1-dependent mRNA decay activity. Ire1P non-canonically splices the mRNA for Xbp1 in the cytoplasm. This spliced Xbp1 serves as mRNA encoding a transcription factor for unfolded protein response genes. Meanwhile the mRNA decay function of Ire1P degrades other cellular mRNAs and can cause changes to the translation machinery by altering regulators in a cell specific manner. Naïve splenic B cells differentiate into Antibody Secreting Cells and activate Ire1 phosphorylation early on after LPS stimulation, within 18 hrs. When Ire1 is activated in B cells, in addition to Xbp1 splicing, there are large-scale changes in mRNA; inhibition of the mRNA degradation function of Ire1 both reduces the number and changes the type of genes involved in altered splicing patterns, including factors for snRNA transcription. Some of the splicing changes seen at 18 hrs after LPS persist into the late stages of antibody secretion, up to 72 hrs, while others are supplanted by new splicing changes introduced by the induction of ELL2, a transcription elongation factor. ELL2 changes mRNA processing patterns and is necessary for Immunoglobulin secretion. RNA splicing patterns in antibody secreting cells are thus shaped by endo-reticular stress, ELL2 induction, and are associated with changes in the levels of snRNAs.

This study introduces a remote sensing application using satellite imagery to survey a network-scale aggregate stockpile inventory. First, a real scale aggregate quarry site was surveyed using a small Unmanned Aerial Vehicle (sUAV) to produce digital terrain models that enabled analysis of aggregate pile geometry. Second, a lab experiment was designed and performed to validate the applicability of close-range Structure from Motion (SfM) photogrammetry for measuring aggregate piles' physical properties such as volume and density. The other part of the lab experiment delved into direct measurement of aggregate density under varying compaction efforts. These experimental results, in conjunction with some simplifying assumptions, enabled the calculation of aggregate stockpile volumes and estimated weights from satellite imagery. We estimated that an inventory of 4.4 and 1.1 million metric tons of crushed aggregates and Reclaimed Asphalt Pavement (RAP), respectively, stockpiled in Washington State for asphalt production in 2017. The merit of producing such database was further showcased in an example on the economic and environmental impacts of material transportation. We approximated that hauling aggregates from quarry plants to construction sites within Washington State incurs a cost of about $50 thousand to over $4 million, consumes about 0.25 to 20 TJ of energy, and emits 20 to over 1,500 tons of CO₂-eq per asphalt plant annually.

The spin-torsion theory is a gauge theory approach to gravity that expands upon Einstein's general relativity (GR) by incorporating the spin of microparticles. In this study, we further develop the spin-torsion theory to examine spherically symmetric and static gravitational systems that involve free-falling macroscopic particles. We posit that the quantum spin of macroscopic matter becomes noteworthy on cosmic scales. We further assume that the Dirac spinor and Dirac equation adequately capture all essential physical characteristics of the particles and their associated processes. A crucial aspect of our approach involves substituting the constant mass in the Dirac equation with a scale function, allowing us to establish a connection between quantum effects and the scale of gravitational systems. This mechanism ensures that the quantum effect of macroscopic matter is scale-dependent and diminishes locally, a phenomenon not observed in microparticles. For any given matter density distribution, our theory predicts an additional quantum term, the quantum potential energy (QPE), within the mass expression. QPE induces time dilation, distance contraction, and thus mimics a gravitational well. When applied to cosmology, our theory yields a static cosmological model. The QPE serves as a counterpart to the cosmological constant introduced by Einstein to balance gravity in his static cosmological model. The QPE also offers a plausible explanation for the origin of the Hubble redshift (traditionally attributed to the universe's expansion). The predicted luminosity distance-redshift relation aligns remarkably well with SNe Ia data from the cosmological sample of SNe Ia. In the context of galaxies, QPE functions as the equivalent of dark matter. The predicted circular velocities align well with the rotation curve data from the SPARC (Spitzer Photometry and Accurate Rotation Curves database) sample. Importantly, our conclusions in this paper are reached through a conventional approach, with the sole assumption of the quantum effects of macroscopic matter on large scales, without the need for additional modifications or assumptions.

Vancomycin is one of the ‘last-line’ classes of antibiotics used in the treatment of life-threatening infections caused by Gram-positive bacteria. Even though vancomycin was discovered in 1950s it was widely used after 1980s for the treatment of infections caused by methicillin-resistant Staphylococci as prevalence of such strains were increased. However, currently it is evident that vancomycin resistant Staphylococcusaureusandvancomycin-resistant Enterococci have been developed as a result of various reasons including use of avaparcin, which is an analog of vancomycin, as feed additive in livestock. In present day context, more attention should be paid on prevention of emergence of resistance for the antibiotics in order to keep antibiotics effective. In order to prevent emergence of resistance, proper guidance for the responsible use of antimicrobials is indispensable. Therefore, almost all stakeholders who use antibiotics should have in depth understanding on the antibiotic they use. As such, it is imperative to be aware of the important aspects of vancomycin. In the present review, efforts have been made to discussthe pharmacokinetics and pharmacodynamics, indications, emergence of resistance, control of resistance, adverse effects and alternative therapy for vancomycin.

Diarrhea remains one of the leading causes of mortality worldwide, especially among children. Recent epidemiological studies conducted in developing countries identified Shigella species as the most predominant pathogenic bacteria responsible for diarrhea. Antimicrobial therapy is necessary for Shigella infections; however, the rapid emergence of resistance against existing antimicrobials in Shigella spp. poses a serious global health problem. To identify alternative antimicrobial compounds with activity against Shigella species, the pathogens responsible for bacterial diarrhea. In this study, we have applied antibacterial phenotypic screening to identify potent anti-Shigella compounds across a broad chemical diversity, including selected acetaminophen derivatives containing benzothiazoles backbone, and their combination with certain antibiotics. In continuation to our effort in searching potent antimicrobial compounds, we have found this time around that two acetaminophen derivatives containing benzothiazoles backbone (4a and 4b) could inhibit the growth of Shigella flexneri with common MIC value of 12.5 µg/ml. These compounds were established through a time-kill kinetics’ study to be bactericidal. Meanwhile, the 2-aminobenzothiazoles (1a and 1b) used for the synthesis of compounds 4 (a & b) were found to be poorly active (MIC: 100 µg/ml) against this pathogen. Combination studies of 4a and 4b with the least susceptible antibiotics (ceftriaxone and cotrimoxazole) demonstrated synergistic anti-Shigella activity. The present study demonstrates that the azobenzothiazole dyes 4 (a & b) can be repurposed as potential anti-Shigella compounds, which can serve as scaffolds for the development of new agents against infectious diarrhea caused by Shigella and other enteric pathogens, especially in developing countries.

It is necessary to address the scarcity of crushed stones for pavement structural layers. So fly ash can be proved to be promising solution as more than 270 tonnes of fly ash is generated in India. Though, numerous research has been conducted for the use of fly ash intreated and untreated form, high volume of fine particles and brittleness of the stabilized fly ash pose a great problem for its use in subbase and base. Moreover, stiffness or modulus of stabilized fly ash is vital elastic parameter which is used for mechanistic pavement design. Hence, in this study an extensive experimental investigation is carried out to study its strength and stiffness properties such as compressive strength, indirect tensile strength and flexural strength, cyclic indirect tensile modulus and flexural modulus of fiber reinforced cement stabilized fly ash, stone dust, aggregate mixtures. The stone dust and aggregates have been added to enhance the gradation of the composite’s mixture. The study presents the effect of fiber on strength and stiffness properties. The experimental result reveals that addition of polypropylene (PP) fibers up to 0.25 wt.% enhances the compressive strength and any further addition of fiber results in decrease of the strength. However, indirect tensile strength and flexural strength increases with increase in fiber percentage up to 0.5 wt.%. Cement content is observed to be the dominant parameter for stabilized materials. Suitable relationships have been developed between strength and modulus parameters for stabilized mixtures. Based on the strength and stiffness study, 70% fly ash and 30% stone dust-aggregate and 60% fly ash and 40% stone dust-aggregate with 6% cement can be considered for the base layer. Based on the indirect tensile strength and flexural strength behavior, 0.35% is considered as the optimum fiber percentage.

Soil is an extremely significant resource for human survival, and agglomerates, as the basic unit of soil structure, not only enhance soil fertility and control the biological validity of nutrients, but also strengthen the soil's erosion resistance. The mass application of fertilizers may have a significant impact on crop growth and soil structure, and the rational application and dispensing of fertilizers will be an urgent issue to be addressed. Therefore, the effect of fertilizer application on the stability of water-stable soil aggregates needs to be studied under different meteorological and soil conditions to draw more general and feasible conclusions. Our Meta-analysis of data from 220 of 56 published studies found that fertilizer application increased mean weight diameter (MWD) by an average of 18% compared to the no-fertilizer treatment. Among the nitrogen (N), phosphate (P), and organic (OM) fertilizer treatments, the organic fertilizer treatment had a greater stimulatory effect on MWD (26%). Among the different fertilizer levels, low level of phosphorus (<40kg·hm-2·yr-1), high level of N (>120kg·hm-2·yr-1), and low level of organic fertilizer (<5000kg·hm-2·yr-1) increased MWD by 19%, 14%, and 41% respectively. Across soil types and land use types, the response to MWD was positive for red soils and paddy fields, and the stimulatory effect of organic fertilizer was more significant compared to chemical fertilizer. The regression model showed that the response ratio of MWD was negatively correlated with the response ratio of soil pH and bulk density (BD), and positively correlated with the response ratio of soil organic carbon (SOC) and microbial mass carbon (MBC). Meanwhile, the PLS-SEM model showed that average annual temperature was the main factor affecting the stability of soil aggregates, and the average annual rainfall is the secondary factor. Therefore, this study found that the long-term use of organic fertilizers in place of some chemical fertilizers was more effective than chemical fertilizer alone. Temperature and rainfall have greater effects on the response of fertilizer to soil aggregate stability.

The present study aimed to evaluate the technical feasibility of using a calcined aggregate with mining residue in different pavement layers, including base, sub-base, and wearing course. For this purpose, the physical characterization of the residue and clay was performed, as well as the production of calcined aggregates at temperatures ranging from 800ºC to 1100ºC. Additionally, the suitability of these aggregates in pavement layers was assessed, considering the current standards. The physical results characterization indicated that the studied clay is suitable for manufacturing calcined clay aggregates since the particle size distribution showed ceramic potential - according to the Winkler diagram - and presented a plasticity index (PI) higher than 15%. In the tests of boiling-induced mass loss and unit mass, the values obtained were within the limits established by the standards, being lower than 10% and 0.88 g/cm3, respectively. Regarding the abrasion loss test, the M1100 aggregate showed "Los Angeles" abrasion values lower than the limit established by the standard, demonstrating its potential as an artificial aggregate in pavement applications.

To improve the interfacial compatibility between cement matrix and expanded polystyrene (EPS) in the core-shell lightweight aggregates (CSLA), the effects of sodium silicate, Polyvinyl alcohol (PVA) emulsion, Vinyl acetate-ethylene (VAE) emulsion, acrylic acid, and acetic acid on the cement-EPS interface were investigated. The denseness of the interface was studied by scanning electron microscopy (SEM), and the effect of interfacial agents on the hydration process of cement was studied by the heat of hydration and induction resistivity. The macroscopic properties of the interface of the CSLA were characterized by the "leak-white" rate, drop resistance and numerical crushing strength. The results show that the sodium silicate densifies the interface by generating hydration products on the EPS surface. At the same time, organic acid enhances the interfacial properties of EPS and cement by increasing the surface roughness and allowing hydration products to grow in the surface micropores. In terms of the cement hydration process, both two interfacial agents delay the cement hydration. Above all, with comprehensive interface properties, "leak-white" rate, and mechanical properties, VAE emulsion and sodium silicate can achieve the best performance with a final crushing resistance of 5.7 MPa.

The brittle shear failure of reinforced concrete beams is complexed and unfavorable. For decades, research on the mechanical properties and durability of recycled coarse aggregate (RCA) to make recycled aggregate concrete (RAC) has been widely investigated. However, test results on the shear strength of reinforced recycled aggregate concrete beams are still limited and contradictory. This paper reports the shear strength of reinforced recycled aggregate concrete beams without stirrups. Eight RAC beams and two controlled beams with natural coarse aggregate (NCA) were tested under the four-point flexural test with the shear span-to-effective depth ratio (a/d) of 3.10. Parameters in this study were the replacement percentage of RCA (0%, 25%, 50%, 75%, and 100%) and longitudinal reinforcement ratio (w) of 1.16% and 1.80%. It was found that the normalized shear stresses of RAC beams with w = 1.80% at all levels of replacement percentage were quite similar to that of the NAC counterparts. Normalized shear stress of the beam with 100% RCA and w = 1.16% was lower than that of the NAC beam by 5%. Database of 128 RAC beams without shear reinforcement from literature was analyzed to evaluate the ability of the most recent ACI 318-19 shear provisions in shear strength prediction. A reduction factor of 0.75 is proposed to the current ACI code provision to account for the physical variations of RCA such as replacement percentage, RCA source and quality, density, amount of residual mortar, and physical irregularity.

The paper presents the influence of different curing conditions – wet, dry and protection against water evaporation on selected properties of concretes with different amount of recycled concrete aggregate previously subjected to atmospheric CO2 sequestration. Additionally, the eco-efficiency bi and ci indexes as well as eco-durability S-CO2 index were calculated. It was found that dry conditions deteriorate the properties of concrete, especially made of blast furnace slag cement, while protection against evaporation allows to achieve results comparable to wet conditions. Moreover, for series with the highest amount of coarse recycled aggregate and after longer period of curing, the difference between the effects of wet curing and protection against water evaporation disappears. The eco-efficiency and eco-durability indexes approach confirms the beneficial effect of blast-furnace slag cement used as a binder but on condition of proper way of curing.

Electric arc furnace oxidizing slag (EAF) has a high density of 3.0~3.7 t/m3 and therefore has a high bulk density when mixed with concrete. Extensive research has been conducted on the use of concrete with high unit volume weight as heavyweight concrete for radiation shielding concrete. In this study, to examine the possibility of developing a radiation shielding concrete, the physical properties of normal concrete, magnetite concrete, EAF concrete, and EAF concrete with added iron powder, were compared. Also, their radiation shielding performance was assessed through shielding tests against X-rays and γ-rays. While the unit volume weight of EAF concrete (3.21 t/m3) appeared lower than that of magnetite concrete (3.5 t/m3), the compressive strength of EAF concrete was greater than those of magnetite and normal concretes. The radiation shielding ratio of magnetite concrete was observed to be 93.9% from the X-ray shielding test, followed by 91.2% of EAF concrete, and 73.7% of normal concrete, indicating a linear relationship with unit volume weight. From the γ-ray shielding test, the performance of EAF and magnetite concretes appeared to be similar. Based on the excellent physical properties and radiation shielding performance of EAF concrete, its potential applicability as radiation shielding concrete was confirmed.

We are encouraged to look beyond ɅCDM as there are no satisfactory explanations for either dark energy or dark matter. A data centred phenomenological approach supports an explanation where dark energy is Holographic Dark Information Energy, HDIE. HDIE explains many effects attributed separately to Ʌ and CDM. HDIE mimics Ʌ with sufficient energy and an equation of state parameter, w= -1.03±0.05 at redshifts z<1.35 to account for accelerating expansion. HDIE is clumped around galaxies at densities that distort space-time, explaining many CDM attributed effects. The present ratio of HDIE/baryons ~2.15, required for the observed expansion history, is equivalent to a dark matter fraction ~68%, consistent with many galaxies. The HDIE/baryon model is based largely on proven physics, provides a common explanation for dark energy and dark matter, and solves the cosmological coincidence problem. At earlier times, z > ~1.35, HDIE was phantom, w = -1.82±0.08, enabling the model to be falsified. HDIE fits Planck dark energy wo-wa plots at least as well as Ʌ, and is consistent with other results that suggest dark energy was phantom at earlier times. A new w-parameterisation is proposed, as the usual CPL parameterisation is biased and unsuitable for distinguishing between HDIE/baryon and ɅCDM models.

In this work the effect of recycled concrete aggregate modified with mineral admixtures and Nano-silica on the mechanical properties and performance of the concrete was investigated after curing in tap water for 28 and 90 days. The compressive, ƒc, indirect tensile, ƒt, and flexural, ƒb, strengths for cured concrete specimens were measured and concrete strength ratios were analyzed. The water and rapid chloride permeability were measured. SEM analysis of microstructure was, also, investigated. The coarse aggregates used were dolomite (control) and recycled concrete aggregate with the incorporation of different mineral admixtures including ground granulated blast slag and granite as well as Nano-silica. It was found that, the slump values of the dolomite concrete decreases compared with recycle aggregate concrete. The results indicate that, the concrete mix containing recycle aggregate have the highest compressive strength, tensile strength and flexural strength compered to concrete mix containing dolomite aggregate. As far as the compressive strength is concerned, the addition 1 % NS and 15 % of slag improved the physico-mechanical properties of the recycled aggregate concretes compared to the other mixes after curing in tap water.

Due to its application as an anti-cancer drug, pazopanib (1) has attracted the interest of many researchers and several studies on pazopanib synthesis have been reported over the years. This paper provides a novel route for synthesizing N,2,3-trimethyl-2H-indazol-6-amine (5) which is a crucial building block in the synthesis of pazopanib from 3-methyl-6-nitro-1H-indazole (6). By alternating between the reduction and two methylation steps compound 5 was obtained in comparable yield (55.0%) to what has been reported (54%). Noteworthy, the last step of N2-methylation also yielded N,N,2,3-tetramethyl-2H-indazol-6-amine (5’) as a new compound ever reported. Furthermore, the data presented in this paper can serve as instrumental for future research aimed at further refining the synthesis process of pazopanib.

In this study, various percentage combinations of waste aggregates such as PET and crumb rubber were used to replace coarse and fine aggregates in natural rubber latex (NRL) modified concretes. Engineering properties such as compressive and flexural strengths, modulus of elasticity, and toughness obtained from compressive- and flexural stress-strain curves were investigated. Scanning electron microscopy (SEM) analysis was performed to examine the microstructural properties and to study the strength development of the studied concretes. The results indicated that both the compressive and flexural strengths of NRL-modified concretes with PET and crumb rubber aggregate replacements decreased with increasing replacement ratios. SEM analysis indicated that PET and crumb rubber (hydrophobic and non-polar materials) can affect the microstructure of the studied concrete by creating a weak interface between the aggregate and cement pastes, leading to reducing strength development. With the addition of the NRL additive, the film formation was found to act as a bridge and improved the bond strength of aggregates and hydration products of NRL-modified concrete. Furthermore, the integration of PET and crumb rubber aggregate can enhance the ability of the concrete to absorb energy and improve ductility. It was found that 10% of PET and crumb rubber aggregate replacement can be used for NRL-modified concrete as a rigid pavement, as its compressive and flexural strengths met the minimum requirement specified by the Department of Highways, Thailand. This research helps repurpose waste materials and reduce the environmental footprint of concrete production.

To achieve sustainable development during urbanization, construction waste is recycled for use as an aggregate in recycled concrete (RC). To determine the influence of the brick content in coarse recycled aggregates on the damage sustained by the resultant RC, the RC was first divided into seven phases: natural crushed stone, old gravel inside waste concrete, bricks, new mortar, old mortar on waste concrete surfaces, and new and old interface transition zones. The Monte Carlo method was then applied to establish a two-dimensional random aggregate model of the RC made with coarse brick aggregates. The ABAQUS software package was used to simulate a uniaxial compression test, the results of which were combined with those of a macro-test to determine the internal damage change rule of brick-containing RC. The stress–strain curves obtained from the simulation coincided well with that of the macroscopic tests. As the brick content increased, the damage zone inside the specimen and the number of microcracks increased. The stress concentration area decreased, as indicated by a lower compressive strength in the macro-test. The results indicate that higher brick contents in RC yield more initial damage inside the concrete and a lower compressive strength.

Despite several decades’ effort to detect and identify phytoplasmas (Tenericutes: Mollicutes) using PCR and Sanger sequencing focusing on diseased plants, knowledge of phytoplasma biodiversity and vector associations remains highly incomplete. To improve protocols for documenting phyto-plasma diversity and ecology, we used DNA extracted from phloem-feeding insects and com-pared traditional Sanger sequencing with a next-generation sequencing method, Anchored Hy-brid Enrichment (AHE) for detecting and characterizing phytoplasmas. Among 22 of 180 leaf-hopper samples that initially tested positive for phytoplasmas using qPCR, AHE yielded phyto-plasma 16Sr sequences for 20 (19 complete and 1 partial sequence) while Sanger sequencing yield-ed sequences for 16 (11 complete and 5 partial). AHE yielded phytoplasma sequences for an addi-tional 7 samples (3 complete and 4 partial) that did not meet the qPCR threshold for phytoplasma positivity or yielded non-phytoplasma sequences using Sanger sequencing. This suggests that AHE is more efficient for obtaining phytoplasma sequences. Twenty-three samples with sufficient data were classified into eight 16Sr subgroups (16SrI-B, I-F, I-AO, III-U, V-C, IX-J, XI-C, XXXVII-A), three new subgroups (designated as 16SrVI-L, XV-D, XI-G) and three possible new groups. Our results suggest that screening phloem-feeding insects using qPCR and AHE sequencing may be the most efficient method for discovering new phytoplasmas.

Despite many calls to reduce or eliminate the use of mechanical restraint, it is still widely used in many countries. Studies using patient interviews have a very clear message: Patients experience mechanical restraint as the most humiliating intervention. There seems to be a lack of alternatives with violent patients. We developed a method using 30 kg bags, originally designed for fitness purposes, to be attached to a patient's wrist or ankle under 1:1 supervision. The method was tested with 10 experienced nurses and de-escalation trainers. A video was made and presented to six outpatients who had previously experienced mechanical restraint. All participants were interviewed. Transcribed interviews were analysed using qualitative content analysis. All participants approved of the method as a milder and less humiliating alternative to mechanical restraint. Nurses' main concerns were the risk of falls and the use of the bags as a weapon. The latter could be controlled by using an additional bag. Patients were generally positive, especially if there was a history of abuse. The method should be further developed to replace at least part of mechanical restraints. As with all ‘milder means‘, care should be taken to really replace restraint and not to introduce additional coercion.

Location-and-scale transformation of a random variable underpins normal distribution, but it is however fundamentally incorrect for scale estimation such as relative dispersion. In this paper, a parametrized alternative to a normal distribution, called scaloc-normal distribution, is proposed that efficiently works and is fundamentally correct with absolute and relative dispersion estimators. The Monte Carlos simulation experiment was used to generate a total of 600,000 artificial datasets in 600 different simulation scenarios from loc-normal (normal) and scaloc-normal distributions. The absolute and relative dispersion were estimated and compared from the two distributions. The results show that scaloc-normal distribution is a good parametrized alternative to loc-normal distribution, fundamentally correct and efficient with both standard deviation and coefficient of variation. The key statistical advancement from loc-normal to scaloc-normal distribution is its fundamental correctness (i.e., scale-invariant property) with an efficient relative estimator of dispersion (i.e., coefficient of variation). Parametrically, the loc-normal and scaloc-normal distributions are very different, but both have linear transformations.

Rigid pavements at military airfields experience surface deterioration within 6-18 months of construction. The cause of this degradation is mainly due to combined exposure to repeated heat shocks from jet engine exhaust and spilled aviation oils (hydrocarbons). Surface degradation occurs in the form of disintegration of aggregates and cement paste into small pieces that pose severe risks of physical injury to maintenance crews or damage to an aircraft engine. Since coarse aggregates typically occupy 60-80% of the concrete volume, aggregates' thermal properties and microstructure should play a crucial role in the degrading mechanism. At high temperatures, concrete with lightweight aggregates is reported to have better performance compared to concrete with normal-weight aggregate. Thus, the present study carried out a detailed investigation of the mechanical and thermal performance of lightweight aggregate concrete exposed to the combined effects of high temperature and hydrocarbon oils simultaneously. To identify the resistance of different concrete with various lightweight coarse aggregates, pumice, perlite, lytag (sintered fly ash), and crushed brick were used as lightweight coarse aggregates in concrete. Also, basalt aggregate concrete was used as a reference. After cyclic exposures, all specimens were tested for residual mechanical, thermal, chemical, and microstructural properties. Overall, concrete with crushed brick aggregate and LYTAG used in this study showed superior resistance to the simulated airfield conditions.

It remains unclear in the literature what is the cause of the so-called alkali-carbonate reaction (ACR) damage to concrete yet, a consensus is reached when considering dedolimitization as non-expansive. However, expansion and cracks as distress features are often attributed to alkali-silica reaction (ASR) when evidence of a reactive mineral is found in the aggregate. Evidently, different types of aggregates may produce different types and degrees of damage. Therefore, this work aims to assess the damage to concrete generated and propagated by the so-called ACR susceptible reactive Kingston coarse aggregate through mechanical testing (i.e., direct shear test), microscopy (the damage rating index – DRI), and other techniques. Distinct induced expansion levels (i.e., 0%, 0.05%, 0.12%, and 0.20%) were selected to compare the distress caused by ACR to concrete affected by ASR. Result show that the behaviour of ACR, namely as captured through the DRI, is inconsistent with that of ASR thus attesting to ACR being a distinct distress mechanism.

This study introduces numerical advancements in an alternative design for the SPS Beam Dump Facility (BDF) at CERN. The design envisions a high-power operation target made of flowing liquid lead. The BDF is a proposed versatile facility at CERN, intended for both beam-dump-like and fixed-target experiments. The target behavior is assessed, assuming a proton beam with a momentum of 400 GeV/c, a pulse frequency of 1/7.2 Hz, and an average beam power of 355 kW. An evaluation is conducted using various Computational Fluid Dynamics (CFD) codes to analyze the behavior of liquid lead and to predict the thermal stress on the target vessel induced by the pulsed heat source generated by the charged particle beam. The comparison increases the reliability of the results, investigating the dependencies on the CFD modeling approach. The beam is modeled as a volumetric heat source with data coming from beam-lead interaction simulations provided by CERN and obtained with the Monte-Carlo code FLUKA. The velocity field and stress profiles are utilized to enhance the design of the lead loop and verify its viability and safety when operated with a liquid metal target.

The availability of petroleum asphalt, derived from non-renewable sources, is steadily declining alongside diminishing petroleum reserves. To reduce reliance on petroleum, alternative renewable natural sources are being explored as both modifiers and replacements for petroleum asphalt, particularly in asphalt binders. This study explores the chemical, rheological, and mechanical properties of Gopal, a bio-asphalt derived from Gondorukem (gum rosin) and crude palm oil (CPO). Two Gopal variants, Gopal-GEM130 and Gopal-GEG90, were analyzed using FTIR and EDX methods, with Pen 60 petroleum asphalt as a control. The results reveal that Gopal-GEG90 and Gopal-GEM130 exhibit 86% chemical similarity to Pen 60 asphalt. Gopal-GEM130 is less toxic and less alkaline compared to Pen 60, while Gopal-GEG90 is less toxic but more alkaline. Both variants fall under the same classification as Pen 60 in terms of rheological properties, with Gopal-GEG90 demonstrating slightly better stripping resistance but lower aging resistance. Gopal-GEM130 showed better stripping resistance and rutting performance, though with lower fatigue resistance and faster aging compared to Pen 60 asphalt. Both bio-asphalt variants align with performance grade PG64S, signifying their potential as alternatives to conventional petroleum asphalt.

Abstract: The search for alternative protein sources to soy-bean meal (SBM) in animal feeding is a strategic objective to reduce production costs and contribute to a sustainable animal produc-tion. Spirulina, due to the high protein content, has emerged as a potential cost-effective, sus-tainable, viable and high nutritional value food resource for many animal species. Insect larvae (Tenebrio molitor and Hermetia illucens) are also considered potential alternatives to SBM, given their high edible percentage of almost 100%, as well as a protein value higher than that of vegetable proteins. Rapeseed meal and grain legumes, such as faba beans, peas, lupins and chickpea can also be used as locally producible protein ingredients. This study reviews the nutritional value of these potential alternatives to SBM in pig diets, effects on animal perfor-mance, digestion, immune system, physicochemical and sensorial characteristics of meat, in-cluding processed meat products of pork. Limits on their use in pig feeding are also reviewed to indicate gaps to be filled in future research on the supplementation level of these potential al-ternative protein sources into pig diets.

Optic neuritis (ON) is the most common cause of vision loss in young adults. It manifests as acute or subacute vision loss, often accompanied by retrobulbar discomfort or pain on eye movements. Typical ON is associated with Multiple Sclerosis and is generally mild and steroid-responsive, whereas atypical forms are characterized by unusual features, such as optic disc edema, poor treatment response and bilateral involvement, and are often associated with autoantibodies against aquaporin-4 (AQP4) and Myelin Oligodendrocyte Glycoprotein (MOG). However, in rare cases AQP4 and MOG antibodies will come back negative, plunging the clinician in a diagnostic conundrum. Seronegative ON warrants a broad differential diagnosis, including autoantibody-associated, granulomatous, and systemic disorders. These rare forms need to be identified promptly, as their management and prognosis is greatly different. The scope of this review is to describe possible, rarer etiologies of ON when AQP4 and MOG antibodies are negative and discuss their diagnosis and treatment.

Alternative splicing (AS) is a gene regulatory mechanism modulating gene expression in multiple ways. AS is prevalent in all eukaryotes including plants. AS generates two or more mRNAs from the precursor mRNA (pre-mRNA) to regulate transcriptome complexity and proteome diversity. Advances in next-generation sequencing, omics technology and bioinformatics tools, and computational methods provide new opportunities to quantify and visualize AS-based quantitative trait variation associated with plant growth, development, reproduction, and stress tolerance. Domestication, polyploidization and environmental perturbation may evolve novel splicing variants associated with agronomically beneficial traits. To date, pre-mRNAs from many genes are spliced into multiple transcripts that cause phenotypic variation for complex traits, both in model plant Arabidopsis and field crops. Cataloguing and exploiting such variation may provide new paths to enhance climate resilience, resource-use efficiency, productivity, and nutritional quality of staple food crops. This review provides insights into AS variation alongside gene expression analysis to select for novel phenotypic diversity for use in breeding programs. AS contributes to heterosis, enhances plant symbiosis (mycorrhiza and rhizobium), and provides a mechanistic link between the core clock genes and diverse environmental clues.

Porous ceramics can be realized by different methods and are used for manifold applications, like cross-flow-membranes or wall-flow-filters, porous burners, solar receivers, structural design elements or catalytic supports. Within this paper three different alternative process routes are presented, which can be used to manufacture porous ceramic components with different properties or even graded porosity. The first process route bases on additive manufacturing (AM) of macro porous ceramic components, the second on AM of a polymeric template, which is used to manufacture porous ceramic components via replica technique. Finally, the third process route bases on an AM technology, which allows the manufacturing of multi-material or multi-property ceramic components, like components with dense and porous volumes in one complex shaped component.

This study assesses the pursued impacts of Tulsi value chain development intervention on the livelihoods of rural poor in Uttarakhand state of India. Tulsi as an alternative livelihood, particularly for the rural poor, is less explored. With increased crop depredation of major cereal crops grown in the district by wild animals and pests, and decreasing availability of water agriculture, attempts were made to improve earnings from Tulsi as an alternative livelihood. Findings suggest that the average households’ gross profit from Tulsi farming increases by more than double within a span of two years. Total crop income of beneficiary farmers’ increases by 0.8 percent for every 1 percent increase in Tulsi income. Intervention helped enhance productivity of Tulsi, thereby enhancing earnings from Tulsi farming. Most importantly, intervention has shown a tremendous adoption rate. Towards the end of the intervention, the value chain work was out-scaled to another 19 villages in Chamoli district, thereby reaching out to more than 400 households.

Research interest in the occurrence, distribution, fate, and toxicity of N-(1,3-Dimethylbutyl)-N’-phenyl-p-phenylenediamine (6PPD) quinone, a derivative of the tire amino antioxidant 6PPD in urban environments, has surged. While several studies have found that 6PPD quinone exhibits acute, reproductive, and behavioral toxicity as well as mutagenicity and hepatotoxicity in aquatic and terrestrial animals, its environmental exposure data are fragmented and lack coherence across the source-to-exposure continuum, making it difficult to use for risk assessment and regulatory purposes. The present work developed an aggregate exposure pathway (AEP) framework to integrate the exposure data. An AEP network was developed for the atmospheric deposition of 6PPD quinone from tire wear in the Pearl River Delta, which led to human exposure. The 6PPD quinone research was organized, visualized, and evaluated with pertinent knowledge gaps identified using the weight of evidence assessment. Eight key exposure states were identified, with only two having high confidence levels and three having low confidence levels. Empirical support for the key transitional relationships decreased from High to Low from the source to the target site, indicating an urgent need for downstream mechanistic data. The proposed AEP framework integrated diverse 6PPD quinone research, facilitating a mechanistic understanding of the source-to-outcome continuum, as well as the development of quantitative predictive models for future research and environmental regulation.

Peri-implantitis continues to be one of the major reasons for implant failures. We propose a new approach for incorporating MTA into Zirconia implant surfaces with Nd:YAG laser and investigate the biological response of peri-implant cells as well as the microbiological response. Discs of Zirconia stabilized with Yttria and Titanium were produced according 4 tested groups: Nd:YAG laser textured Zirconia coated with MTA (Zr MTA); Nd:YAG laser textured Zirconia (Zr Textured); Zirconia and Titanium discs (Zr and Ti ). Contact profilometry was used to evaluate surface roughness. Human osteoblasts, gingival fibroblasts and S. oralis were cultured on samples. Cell adhesion and morphology, cell viability, cell differentiation markers and bacterial growth were assessed. Zr Textured roughness was significantly higher compared to all other groups. Cellular adhesion was observed at 1 day in all samples in both cell lines. Osteoblasts viability was lower in Zr MTA group, unlike fibroblasts viability was shown to be higher in Zr MTA group compared to Zr Textured group at 3 and 7 days. Osteocalcin and IL-8 release by osteoblasts were higher in Zr MTA. Zr Textured showed higher IL-8 values released by fibroblasts. No differences in S. oralis CFUs were observed between groups. The results suggest that Zirconia implant surfaces coated with MTA seems to promote fibroblasts proliferation and osteoblasts differentiation, however does not appear to have antibacterial properties.

Heat index (HI) is a biometeorological indicator that combines temperature and relative humidity. This study aimed to investigate the relationship between heat index and daily counts of diarrhoea hospitalisation in Dhaka, Bangladesh. Data on daily diarrhoea hospitalisations and meteorological variables from 1981–2010 were collected. We categorised heat index of >94.3°F, >100.7°F and >105°F as high, very high and extremely high heat index, respectively. We applied time-series adjusted generalised linear model (GLM) with negative binomial distribution to investigate the effects of heat index and extreme heat index on hospitalisations for diarrhoea. Effects were assessed for all ages, <5 children and by gender. A unit higher HI, and high, very high and extremely high HI were associated with 0.8%, 8%, 7% and 9% increase in diarrhoea hospitalisation in all ages, respectively. The effects varied slightly by gender and were most pronounced in <5 children with a rise of 1°F in high, very high and extremely high HI associated with a 14.1% (95% CI: 11.3% – 17.0%), 18.3% (95% CI: 13.4% – 23.5%) and 18.1% (95% CI: 8.4% – 28.6%) increase of diarrhoea, respectively. This suggest that heat index may serve as an alternative indicator for measuring the combined effects temperature and humidity on diarrhoea.

Growing popularity of smart and integrated buildings requires a review of methods to optimize the preheat of ventilation air. An integrated system permits using heat ex-changers located in the mechanical room or in the future even using an exterior wall as a heat exchanger. One may ask the question how does the earth-air heat exchanger (EAHX) technology fitts into this function. EAHX has many advantages but also has many unanswered questions. Some of the drawbacks are: a possible entry of radon gas, high humidity in the shoulder seasons as well as the need for two different air intake sources with a choice that depends on the actual weather conditions. While in winter, the EAHX may be used continuously to ensure thermal comfort, in other seasons, its operation must be automatically controlled. To generate the missing information about the EAHX technology we reviewed literature and examined two nearly identical EAHX systems, placed either in ground next to the building or under the basement slab. Effectively, the information provided in this paper, shows advantages of merging both these approaches while the EAHX shoud be placed under the house or near the basement foundation.

Current stock market forecasting methods encompass fundamental, technical, emotional, and bargaining factors. Predominantly, price prediction hinges on order volume and price, although correlating these two within existing models proves challenging. This study employs Cycle Generative Adversarial Network (Cycle GAN) to unravel the intricate price-volume relationship, combining it with Bollinger Bands for trading signal analysis, overcoming hurdles in short-term forecasting prevalent in numerical analysis and AI. Focusing on TSMC (2330.TW) stock price, the research leverages Cycle GAN in deep learning to master the price-volume nexus, juxtaposed with LSTM and RNN. Historical TSMC closing prices and transaction counts are model inputs, scrutinizing their interconnectedness for predictions. This innovative approach aligns stock price, volume, market value, taxes, and prior changes via system engineering. By intertwining Bollinger Bands with stock price forecasts, trading signals are distilled, factoring in extended index %b for a comprehensive market picture.

For concrete structures exposed to offshore areas, chloride ion erosion is one of the main factors affecting the durability. It is crucial to evaluate chloride ion permeability resistance of concrete structures. In this article, a finite element simulation of the chloride ion diffusion process in concrete is conducted. A mass diffusion finite element model based on random aggregate approach is established to investigate the influence of aggregate, interface transition zone, and micro-cracks on chloride ion diffusion coefficients in concrete. The results show that the mass diffusion finite element analysis based on the exponential function model and power function model can effectively simulate the chloride ion diffusion process in concrete. In addition, the data reveal that coarse aggregate is the most important factor affecting chloride ion diffusivity in concrete. However, the interface transition zone significantly accelerates chloride ion diffusion in concrete. Moreover, this acceleration effect exceeds the barrier effect of aggregate.

Recycled asphalt mixture is a material remixed with old asphalt recycled material (RAP) and new aggregate, and its application is of great significance in environmental protection.Due to the wear and tear of the old asphalt mixture, the road performance of the recycled asphalt mixture will decrease. This paper uses IPP software to obtain the shape characteristics of the old and new aggregates, and found that the roundness of the old aggregate of 9.5mm-16mm is the most serious wear. Therefore, the 30% RAP, and the influence of the roundness of the recycled asphalt mixture on the road performance is studied.

Recently many researches of EOS (Electric Arc Furnace Oxidizing Slag) on application to construction industry have been carried out with increasing its production and limited reclamation site. EOS can be used as a fine aggregate for construction material, however, its engineering properties vary with the manufacturing process and producing district, causing a quality differences in material performance. In the work, EOS is obtained from steel manufacturing plants in South Korea and the engineering properties are evaluated for EOS and the cement mortar with EOS, respectively. From the tests, EOS is mainly made up of CaO, SiO₂, and FeO with 18.2% of larnite which has a crystal structure of β-C₂S with similar cement mineral. EOS mortar shows an increasing compressive strength with more EOS content, which is affected by a considerable amount of larnite (β-C2S) in EOS. The EOS based mortar with ERS (Electric Arc Furnace Reduction Slag) shows unsatisfactory results over the criteria for rate of change, which implies that more consideration must be taken for the usage of the mixed ERS and EOS for cement mortar due to swelling effect of ERS on dimensional stability.

It has long been known that phytohormone auxin plays a promoting role in tuber formation and stress tolerance in potatoes. Our study aimed to identify and characterize the complete sets of auxin-related genes that presumably constitute the entire auxin signaling system in potato (Solanum tuberosum L.). The corresponding genes were retrieved from sequenced genomes of the doubled monoploid S. tuberosum DM1-3-516-R44 (DM) of the Phureja group, the heterozygous diploid line RH89-039-16 (RH), and the autotetraploid cultivar Otava. Both canonical and noncanonical auxin signaling pathways were considered. Phylogenetic and domain analyzes of deduced proteins were supplemented by their expression profiling and 3D molecular modeling. The canonical and ABP1-mediated pathways of auxin signaling appeared to be well conserved. Total number of potato genes/proteins presumably involved in canonical auxin signaling is 46 and 108 in monoploid DM and tetraploid Otava, respectively. Among studied potatoes, spectra of expressed genes obviously associated with auxin signaling were partly cultivar-specific and quite different from analogous spectrum in Arabidopsis. Most of the noncanonical pathways found in Arabidopsis appeared to be low probable in potato. This was equally applied to all cultivars used irrespective of their ploidy. Thus, some important features of the (noncanonical) auxin signaling pathways may be variable and species-specific.

Alternative fuels containing biocomponents produced in various technologies are introduced in aviation to reduce its carbon footprint but there is little data describing their impact on the performance and emissions of engines. The purpose of the work is to compare the performance and gas emissions produced from two different jet engines: the GTM-140 microturbine and the full-size DGEN380 turbofan, powered by blends of Jet A-1 and one of two biocomponents: 1) ATJ and 2) HEFA produced from used cooking oil (UCO) in various concentrations. The acquired data will be used to develop an engine emissivity model to predict gas emissions. Blends of the mineral fuel with synthetic components were prepared in various concentrations, and their physicochemical parameters were examined in the laboratory. Measurements of emissions from both engines were carried out in selected operating points using the Semtech DS gaseous analyzer and the EEPS spectrometer. The impact of tested blends on engine operating parameters is limited, and their use does not carry the risk of a significant decrease in aircraft performance or increase in fuel consumption. Increasing the content of biocomponents causes a noticeable rise in the emission of CO and slight increase for some other gasses (HC and NOx), which should not, however, worsen the working conditions of the ground personnel. This implies that there are no contraindications against using tested blends for fuelling gas-turbine engines.

The main goal of the Soil Moisture and Ocean Salinity (SMOS) mission over land surfaces is the production of global maps of soil moisture (SM) and vegetation optical depth (τ) based on multi-angular brightness temperature (TB) measurements at L-band. The operational SMOS Level 2 and Level 3 soil moisture algorithms account for different surface effects, such as vegetation opacity and soil roughness at 4 km resolution, in order to produce global retrievals of SM and τ. In this study, we present an alternative SMOS product which was developed by INRA (Institut National de la Recherche Agronomique) and CESBIO (Centre d’Etudes Spatiales de la BIOsphère). This SMOS-INRA-CESBIO (SMOS-IC) product provides daily SM and τ at the global scale and differs from the operational SMOS Level 3 (SMOSL3) product in the treatment of retrievals over heterogeneous pixels. Specifically, SMOS-IC is much simpler and does not account for corrections associated to the antenna pattern and the complex SMOS viewing angle geometry. It considers pixels as homogeneous to avoid uncertainties and errors linked to inconsistent auxiliary data sets which are used to characterize the pixel heterogeneity in the SMOS L3 algorithm. SMOS-IC also differs from the current SMOSL3 product (Version 300, V300) in the values of the effective vegetation scattering albedo (ω) and soil roughness parameters. An inter-comparison is presented in this study based on the use of ECMWF (European Center for Medium range Weather Forecasting) SM outputs and NDVI (Normalized Difference Vegetation Index) from MODIS (Moderate-Resolution Imaging Spectroradiometer). A 6 year (2010-2015) inter-comparison of the SMOS products SMOS-IC and SMOSL3 SM (V300) with ECMWF SM yielded higher correlations and lower ubRMSD (unbiased root mean square difference) for SMOS-IC over most of the pixels. In terms of τ, SMOS-IC τ was found to be better correlated to MODIS NDVI in most regions of the globe, with the exception of the Amazonian basin and of the northern mid-latitudes.

Recent trends concerning hydrogen as a fuel of the future and problems related to its production, storage and utilization increase the demand for efficient technologies related to these problems. A large part of such technologies is related to application of advanced materials based on various complex oxides which are used as efficient catalysts for fuel transformation into hydrogen and syngas, materials for membranes with selective permeability for hydrogen and syngas production, components of solid oxide fuel cells/electrolyzers as well as many other applications in energy, electrochemistry and catalysis. Such materials are typically based on oxides and solid solutions with perovskite and fluorite structures or their derivatives. Attention is also paid to the materials based on spinel, apatite, mayenite, sheelite, fergusonite structures. The above-mentioned materials are continuously studied in order to modify and optimize their functional properties. On the other hand, other classes of materials (weberites, monazites, etc.) are recently discovered and considered as candidate materials for the aforementioned applications due to their specific functional properties or a great potential of their improvement. In this review, some of these materials are considered.

Background: The use of complementary therapies in the population is increasing, so it is necessary to understand the training that health professionals receive in this type of therapy in their training plans, as they are often the primary source of information for patients. Our objective was to investigate Spanish universities that offer subjects on complementary therapies in their Nursing degree programs. Methods: Observational descriptive cross-sectional study. For this purpose, we used the document published on the website of the Ministry of Universities as a working document. Additionally, a literature search was conducted up to September 2023 in the PubMed database, along with reverse searches. Results: Out of a total of 62 universities, only 16 (29%) offer a subject related to this type of therapy, with most of them being elective courses. Conclusions: The training content on complementary care in Nursing degree programs in Spanish universities is scarce, highlighting the potential benefit of expanding and promoting it, in line with the recommendations of the World Health Organization.

Reducing meat consumption is better for the environment. Unfortunately, commercial plant-based meat substitutes are often more expensive than meat and thus have not seen widespread adoption. This paper analyzes commercially-available spirulina, soy, pea, and brown rice protein isolates characteristics to provide data for non-meat protein cost reductions. Thermal and rheological properties, viscosity, density, and particle size distribution are analyzed for further study on alternative protein-based food processing. Differential scanning calorimetry analysis produced dry amorphous-shaped curves and paste curves with a more distinct endothermic peak. Extracted linear temperature ranges for processing in food production for spirulina was 70-90ºC; soy protein was 87-116ºC; pea protein was 67-77ºC; and brown rice protein was 87-97ºC. Viscosity analysis determined each protein material was shear-thinning and that viscosity increased with decreased water concentration, with rice being an exception to the latter trend. The obtained viscosity range for spirulina was 15,100-78,000cP; soy protein was 3,200-80,000cP; pea protein was 1,400-32,700cP; and brown rice protein was 600-3,500cP. The results indicate that extrusion is a viable method for further processing of the protein isolates as this technique has a large temperature operating range and variable screw speed. Data provided here can be used to make single or multi-component protein substitutes.

This article traces the origination, distribution, kinematics, function, and nature of alternative lateral horse gaits, i.e. intermediate speed lateral-sequence gaits involving the synchronization of ipsilateral limbs in the swing phase. Such alternative lateral horse gaits (namely, the running walk, rack, broken pace, hard pace, and broken trot) have been prized by equestrians for their comfort, and have been found in select horse breeds for hundreds of years and even exhibited in fossil equid trackways. After exploring the evolution and development of alternative lateral gaits via fossil equid trackways, human art and historical writings, and the genetics and history of modern horse breeds, functional and biomechanical reasons are offered for the genesis of these gaits. The article concludes by tracing similarities and differences between and within the expression of these alternative lateral gaits by various horse breeds. Fast and low-swinging hard pacing gaits are common in several horse breeds of East and North Asia, high-stepping rack and running walk gaits are often displayed in European and North and South American breeds, the broken pace is found in breeds of Central Asia, Southeast Asia, West Asia, Western North America, and Brazil in South American, and the broken trot occurs in breeds of North Asia, South Asia, and the Southern United States, and Brazil South America.

Currently, there is increasing industrial demand for rare earth elements (REE) as these elements are now integral to the manufacture of many carbon-neutral technologies. The depleting REE ores and increasing mining costs are prompting to look for alternative sources for these valuable metals, particularly from waste streams. Although REE concentrations in most of the alternate resources are lower than current REE ores, some sources such as marine sediments, coal ash, and industrial wastes like red mud are looking promising with significant concentrations of REE in them. This review focuses on the alternative resources for REE such as ocean bottom sediments, continental shelf sediments, river sediments, stream sediments, lake sediments, phosphorites deposits, industrial waste products like red mud, and phosphogypsum, coal, coal fly ash, and related materials, waste rock sources from old and closed mines, acid mine drainage, and recycling of e-waste. Possible future Moon exploration and mining for REE and other valuable minerals are also discussed. It is evident that REE extractions from both primary and secondary ores alone are not adequate to meet the current demand, and sustainable REE recovery from the alternative resources described here is also necessary to meet the growing REE demand. An attempt is made to identify the potential of these alternative resources and sustainability challenges, benefits, and possible environmental hazards to meet the growing challenges in meeting the future REE requirements.

A progressive and chronic neurological condition called MSA (Multiple System Atrophy) is characterized clinically by varying degrees of dysautonomia, cerebellar ataxia, and parkinsonism. The concept of mitochondrial dysregulation in MSA is one perspective in handling this neurodegenerative disease. Damage to functional mitochondria is driven by the presence of ɑ-Synuclein-induced mitochondrial localization. The goal of MSA treatment up until now has been to reduce symptoms. One of the innovations in the treatment of MSA could be the novel idea based on mitochondrial reprogramming pathways. Mitochondrial reprogramming can be done in various ways in which the use of hydrogen, magnesium and low-dose hydrogen peroxide.

La minería es una industria intensiva en energía que requiere una fuente estable de electricidad. Con el aumento de la demanda de minerales y la disminución de las leyes, se espera que la demanda de energía aumente en un 36% para el 2035. Este aumento de la demanda depende del uso de combustibles fósiles ya que la electricidad producida y comprada en las empresas mineras se basan principalmente en el caso de los combustibles fósiles, los costos de los sistemas de almacenamiento de energía solar y eólica han caído a una escala sin precedentes, lo que alienta a las empresas mineras a probar estas tecnologías.Entre los factores que influyen en el uso de energía renovable, se encuentra el beneficio a la comunidad en la etapa de operación y cierre o post-cierre de un proyecto minero, el siguiente factor es el perfil de consumo eléctrico o demanda es importante para el cálculo de su almacenamiento o no, de las energías renovables a utilizar. Como tercer factor está el cálculo del consumo en los procesos. Los rangos de penetración determinarán si es posible su almacenamiento de energía, y si es posible utilizar control híbrido (solar - eólico), para ello es importante el uso de herramientas digitales como el programa Holmer, es una herramienta importante que técnica y económica.El gobierno debe tener una perspectiva que ayude en los temas regulatorios necesarios para impulsar proyectos de energía renovable con diferentes incentivos e intereses según el contexto minero.

Intercropping of maize (Zea mays L.) and peanuts (Arachis hypogaea L.) (M||P) significantly enhances crop yield. In a long-term M||P field experiment with two P fertilizer levels, we examined how long-term M||P affects topsoil aggregate fractions and stability, organic carbon (SOC), available phosphorus (AP), and total phosphorus (TP) in each aggregate fraction, along with crop yields. Compared to their respective monocultures, long-term M||P substantially increased the proportion of topsoil mechanical macroaggregates (7.6–16.3%) and water-stable macroaggregates (>1 mm) (13.8–36.1%), while reducing the unstable aggregate index (ELT) and the percentage of aggregation destruction (PAD). M||P significantly boosted the concentration (12.9–39.9%) and contribution rate (4.1–47.9%) of SOC in macroaggregates compared to single crops. Moreover, the concentration of TP in macroaggregates (>1 mm) and AP in each aggregate fraction of M||P exceeded that of the respective single crops (P<0.05). Furthermore, M||P significantly increased the Ca2-P, Ca8-P, Al-P, and Fe-P concentrations of intercropped maize (IM) and the Ca8-P, O-P, and Ca10-P concentrations of intercropped peanuts (IP). The land equivalent ratio (LER) of M||P was higher than one, and M||P stubble improved the yield of subsequent winter wheat (Triticum aestivum L.) compared with sole-crop maize stubble. P application augmented the concentration of SOC, TP, and AP in macroaggregates, resulting in improved crop yields. In conclusion, our findings suggest that long-term M||P combined with P application, sustains farmland productivity in the North China Plain by increasing SOC and macroaggregate fractions, improving aggregate stability, and enhancing soil P availability.

Human beings naturally move from one location to another in search of basic necessities. Road transportation is a low-cost, versatile, and widely accessible mode of transportation worldwide. However, using fossil-based (FB) fuels in transportation vehicles is inefficient, generates hazardous gases, and worsens environmental degradation. The current work assesses the application of clean fuels such as biofuels, natural gas, electricity, propane, and other emerging fuels to replace FB fuels in transport vehicles. Unlike FB fuels, the use of biohydrogen, biomethane, biodiesel, and bioethanol in transport vehicles resulted in emission reduction by 70 %, 63 %, 41 %, and 54 %, respectively, while electric vehicles lower maintenance costs, ensuring better engine performance, and better engine efficiency. The adoption of natural gas and propane as alternative fuels for transport vehicles is cost-effective, and promotes environmental sustainability. There is a need for targeted financial, infrastructural, and technical investments to further promote the application of these clean fuels for road transport application. The outcome of the study provides updated information and sensitizes automobile engineers, environmentalists, transport fleet operators, governments, and other stakeholders on the benefits derivable in the adoption of clean fuels as alternatives to FB fuels as transport vehicles fuel.

Market uncertainty has a significant impact on market performance. Previous studies put much efforts in investigations on market uncertainty related to information asymmetry and risk. However, they have neglected the uncertainty inherent in market transactions, which is also an important aspect of market performance, besides quantity of transactions and market efficiency. In this paper, we put forward the concept of transaction entropy to measure the market uncertainty and see how it changes with price. The definition of transaction entropy is the ratio of total information entropy of all traders to quantity of transactions, reflecting the level of uncertainty in making transactions. And the transaction entropy is the lowest at equilibrium, it will be decreasing in a shortage market, and increasing in a surplus market. Additionally, we make a comparison of total entropy of the centralized market with that of the decentralized market, revealing that the price filtering mechanism could effectively reduce market uncertainty. Overall, the introduction of transaction entropy enriches our understanding of market uncertainty and facilitates a more comprehensive assessment of market performance.

The formation of new blood vessels is a critical process for tumor growth and may be achieved through different mechanisms. Angiogenesis represents the first described and most studied mode of vessel formation, but tumors may also use alternative ways to secure blood supply and eventually acquire resistance to anti-angiogenic treatments. These non-angiogenic mechanisms have been described more recently and include intussusceptive microvascular growth (IMG), vascular co-option, and vasculogenic mimicry. Like solid tumors, also in lymphomas angiogenic and non-angiogenic pathways play a fundamental role in tumor growth and progression. In view of the relevant prognostic and therapeutic implications, a comprehensive understanding of these mechanisms is of paramount importance for improving the efficacy of treatment in patients with lymphoma. In this review, we summarize the current knowledge on angiogenic and non-angiogenic mechanisms involved in the formation of new blood vessels in Hodgkin’s and non-Hodgkin’s lymphomas.

Probabilistic and parsimony-based arguments regarding available genetics data are used to propose that Hardy and Higgin’s amyloid cascade hypothesis is valid but is commonly interpreted too narrowly to support, incorrectly, the primacy of the amyloid beta peptide (Aβ) in driving Alzheimer’s disease pathogenesis. Instead, increased activity of the βCTF (C99) fragment of APP is likely the critical pathogenic determinant altered by mutations in the APP gene. This model is consistent with the regulation of APP mRNA translation via its 5’ iron responsive element (IRE). Similar arguments support that the pathological effects of familial Alzheimer’s disease mutations in the genes PSEN1 and PSEN2 are not exerted directly via changes in APP cleavage to produce different ratios of Aβ length. Rather, these mutations likely affect the stability of presenilin holoprotein and/or γ-secretase multimers with consequences for γ-secretase activity and other important cellular functions. All fAD mutations in APP, PSEN1, and PSEN2 likely find unity of pathological mechanism in their actions on endolysosomal acidification and mitochondrial function, with detrimental effects on iron homeostasis and promotion of “pseudo-hypoxia” being of central importance. Aβ production is enhanced and distorted by oxidative stress and accumulates due to decreased lysosomal function. It may act as a disease-associated molecular pattern (DAMP) enhancing oxidative stress-driven neuroinflammation during the cognitive phase of the disease. We also discuss fascinating, but largely ignored, data on presenilin biology that may be important in understanding presenilins’ central role in familial Alzheimer’s disease.

The statistical properties of a good estimator include robustness, unbiasedness, efficiency, and consistency. However, the commonly used estimators of dispersion have lack or are weak in one or more of these properties. In this paper, I proposed statistical mirroring as a good alternative estimator of dispersion around defined location estimates or points. In the main part of the paper, attention is restricted to Gaussian distribution and only estimators of dispersion around the mean that functionalize with all the observations of a dataset were considered at this time. The different estimators were compared with the proposed estimators in terms of alternativeness, scale and sample size robustness, outlier biasedness, and efficiency. Monte Carlo simulation was used to generate artificial datasets for application. The proposed estimators (of statistical meanic mirroring) turn out to be suitable alternative estimators of dispersion that is less biased (more resistant) to contaminations, robust to scale and sample size, and more efficient to a random distribution of variable than the standard deviation, variance, and coefficient of variation. However, statistical meanic mirroring is not suitable with a mean (of a normal distribution) close to zero, and on a scale below ratio level.

The demands for high power and low emissions put focus on energy efficiency when developing new engines. An important part is the UAV engine cooling system, which cools the engine structure below damaging temperatures. For high temperatures in the cooling system there is a risk that boiling occurs and while the initial nucleate boiling enhances the cooling effect, the subsequent Film boiling decreases the heat transfer drastically. It is important to understand the benefits and limitations of various fluids when designing a two-phase cooling system. This paper proposes an alternative organic coolant. Its normal application range is 15°C to 400°C, and its pressure range is from atmospheric to 10.6 bar. DOWTHERM A fluid possesses unsurpassed thermal stability at temperatures of 400°C. This fluid, in both the liquid and vapor form, is noncorrosive toward common metals and alloys. Even at the high temperatures involved, the equipment usually exhibits excellent service life. Original equipment in many systems is still being used after 30 years of continuous service. The numerical results, described in this paper, show the potential of DOWTHERM A as a good alternative for cooling a UAV engine. It will extend the working temperature range of the Diesel engine and will maintain the structural integrity of the piston, cylinder and the piston rings.

The optimal surgical approach for thymoma resection is still an object of debate. The increasing experience in robotic-assisted thoracic surgery (RATS) has led to the progressive affirmation of this technique as a valid alternative to Video-Assisted Thoracic Surgery (VATS), sternotomy and thoracotomy in this setting. The present study aims to compare the post-operative and short-term results of RATS Thymectomy for thymoma with those of other main surgical approaches (sternotomy, thoracotomy, and VATS) from a high-volume single center.Between May 2021 - September 2023, 40 consecutive patients underwent RATS Thymectomy for I to limited-stage III thymoma in our center. Three homogenous groups of consecutive patients who received thymic surgery by main alternative approaches (sternotomy, thoracotomy, VATS) over the last 5 years, were identified in order to perform a comparative analysis. Data of operative technique, time of surgery, associated resections, conversion rate, overall morbidity, tumor size, radicality, postoperative pain, length of hospital stay, and cosmetic results were recorded and compared between each control group and the RATS group. Tumor size was higher in the sternotomy group, but not significantly. The mean operative time of RATS interventions was significantly lower than that of sternotomy and VATS. It was significantly shorter compared to thoracotomy if excluding docking-undocking time. Higher rate of associated adjacent structures resection was reported in the sternotomy group (p=0.005). Conversion rate was significantly higher in VATS group (p= 0.026) compared to RATS. Postoperative pain at 24 and 48 hours was significantly lower in RATS group compared to the others. Improved cosmetics results were reported after RATS compared to sternotomy (p= 0.0001) and thoracotomy (p= 0.001) groups, with a trend towards better results compared to VATS (p=0.05). Length of hospital stay was shorter in the RATS group with a significant difference vs. the sternotomy group (p<0.001). These results from a single center confirm the safety and effectiveness of RATS for the treatment of limited stage thymoma. Advantage in terms of operative outcomes, post-operative pain, cosmetic results, and hospital stay was observed if compared to the alternative approaches. Short-term oncologic outcome was excellent based on the high complete excision rate of the tumor.

There have been beaching events of the marine alga pelagic sargassum in coastal regions of the Caribbean Sea, West African countries, and the north-northeast region of Brazil since 2011. Its presence has caused environmental and socioeconomic impacts while several studies were conducted in order to understand the causes of this phenomenon, as well as alternatives to mitigate its impacts. The objective of this research was to evaluate pelagic sargassum biomass as a raw material for the manufacture of medium-density multilayer particleboards. These are composed of 30% sargassum particles in their inner layer and 70% sugarcane bagasse particles on their outer layers which are bonded with castor oil-based polyurethane resin. A physical and chemical characterization was carried out in order to evaluate sargassum particles while physical and mechanical tests were carried out in order to evaluate the panels. Results were subsequently compared with indications from NBR 14810-2:2018 and ISO 16893:2016 standards. A life cycle assessment based on ISO 14040:2006 and 14044:2006 was carried out as to complement the feasibility study of these panels and to compare their different manufacturing processes. The multilayer panels met the minimum requirements for physical and mechanical properties established by regulations, indicating that the Sargassum spp. biomass can be used as filling. The life cycle assessment study indicates that sargassum panels produced in the Belém-PA-Brazil region present lower environmental impacts in four of seven evaluated categories when compared to conventional panels. As such, they constitute an alternative way to mitigate environmental impacts generated by beaching events.

Despite concepts of human flourishing, a term connected to empowerment that acts as an archi-tectural structure within the development and sustainability discourse, tensions remain between exponential economic growth, planetary health and community empowerment. Scholars argue that the development agenda is maldevelopment due to the unrequested interventions delivered to communities, mainly in the Global South (Shiva, 1999). A current state of disorientation grips the modern world, and despite sophisticated global frameworks like the Sustainable Development Goals (SDGs), internal approaches are side-lined. This research article repositions empowerment and compassion at the centre of the sustainable development discourse by drawing on the Inner Development Framework, particularly goal one – Being – ‘Relationship to Self’ and goal three – Relating – ‘Caring for others and the World’ as a guiding theoretical underpinning. Accordingly, this research article presents a qualitative interpretative study that examines the lived experience of women and their journeys to empowerment. The key findings indicate an intricate relationship between wellbeing and empowerment and the realisation of inner development as a tool to re-imagine alternative futures. The Machiavellian tendency to the sustainability agenda is deeply embedded in the profiteering of the misery of affected communities.

The genetic systems of Paspalum species have not been extensively studied. We analysed the ploidy, reproductive mode, mating system, and fertility of four Paspalum species - P. durifolium, P. ionan-thum, P. regnellii, and P. urvillei. An analysis of 378 individuals from 20 populations of north-eastern Argentina was conducted. All populations of the four Paspalum species were pure tetraploid and had a sexual and stable reproductive mode. However, some populations of P. durifolium and P. ionanthum showed low levels of apospory. Populations of P. durifolium and P. ionanthum had low seed sets under self-pollination but were fertile under open pollination, showing that self-incompatibility likely caused self-sterility. In contrast, populations of P. regnellii or P. urvillei showed no evidence of apospory and seed set in both self- and open pollination conditions were high, suggesting that they are self-compatible, due to the absence of pollen-pistil molecular in-compatibility mechanisms. The evolutionary origin of the four Paspalum species could explain these differences. This study supplies valuable insights into the genetic systems of Paspalum species, which could have implications for their conservation and management.

The present article discusses the institutional model adopted in Brazil regarding energy production through biomass. The theoretical-empirical method is used to conclude that the model's difficulties can be overcome by adopting a network of contracts capable of subjecting renewable energy generation to an energy compensation model.

The existence of the exclusion zone (EZ), a layer of water in which plastic microspheres are repelled from hydrophilic surfaces, has now been independently demonstrated by several groups. A better understanding of the mechanisms which generate EZs would help with understanding the possible importance of EZs in biology and in engineering applications such as filtration and microfluidics. Pollack theorizes that EZ water exists in a new phase which has a layered structure. We note several problems with Pollack's proposed structure, some of which were noted in the 1960's when a similar structure was proposed for ``polywater''. We argue that Schurr's diffusiophoresis based theory presents a compelling alternative explanation for the core EZ phenomena, although there remain other findings from Pollack's lab it does not explain. Among other things, Schurr's theory makes predictions about the growth of the EZ with time which have been confirmed by Florea et al.\ and others. In this work we also introduce and explore a novel hypothesis - that some aspects of EZ phenomena may be attributable to repulsive van der Waals forces. Finally, we touch on several possible confounding factors that make experimentation on EZs difficult, such as charged surface groups, dissolved solutes, and adsorbed nanobubbles.