Aluminum profile surface defects can greatly affect the performance, safety and reliability of products. Traditional human-based visual inspection is low accuracy and time consuming, and machine vision-based methods depend on hand-crafted features which need to be carefully designed and lack robustness. To recognize the multiple types of defects with various size on aluminum profiles, a multiscale defect detection network based on deep learning is proposed. Then, the network is trained and evaluated using aluminum profile surface defects images. Results show 84.6%, 48.5%, 96.9%, 97.9%, 96.9%, 42.5%, 47.2%, 100%, 100%, 43.3% average precision(AP) for the ten defect categories, respectively, with a mean AP of 75.8%, which illustrate the effectiveness of the network in aluminum profile surface defects detection. In addition, saliency maps also show the feasibility of the proposed network.

Density functional theory (DFT) calculations of hydrogen adsorption on titanium nitride had previously shown that hydrogen may adsorb on both titanium and nitrogen sites with a moderate adsorption energy. Further, the diffusion barrier was also found to be low. These findings may qualify TiN, a versatile multifunctional material with electronic conductivity, as electrode material for the hydrogen evolution reaction (HER). This was the main impetus of this work which aims to experimentally and theoretically investigate the electrocatalytic properties of TiN-layers that were processed on Ti substrate using reactive ion sputtering. The properties are discussed focusing on the role of oxygen defects introduced during the sputtering process on the HER. Based on DFT calculations, it is shown that these oxygen defects alter the electronic environment of the Ti atoms which entails a low hydrogen adsorption energy in the range of -0.1 eV; this leads to HER performances that match those of Pt-NPs in acidic media. When a few nanometr thick layer of Pd-NPs is sputtered on-top of the TiN-layer, the performance is drastically reduced. This is interpreted in terms of oxygen defects being scavenged by the Pd-NPs near the surface which is thought to reduce the hydrogen adsorption sites.

Alkaline and alkaline-thermal activation were used in an attempt to synthesize zeolites using the sedimented illite fraction of raw Devonian clays from the Kuprava clay pit in Latvia. The Si/Al molar ratio of these clays is 2.79. Thermal and hydrothermal treatments were conducted using 6M and 10M NaOH solutions, along with different curing environments. The treated samples were analyzed using XRD, FTIR, and SEM, and were compared to the raw and calcined illite fraction samples. The main phase that forms after alkaline treatment is hydrosodalite (Na8[AlSiO₄]₆(OH)₂∙2H₂O). Using a higher concentration of NaOH leads to a significant increase in hydrosodalite formation. Increasing the curing temperature from 120°C to 600°C slightly reduces hydrosodalite formation due to the crystallization of the nepheline (Na₃K(Al₄Si₄O₁₆)) phase. This phase forms relatively intensively when the chemically treated samples are cured in a nitrogen environment at 600°C, thereby reducing the formation of hydrosodalite. The characteristic layered-fused structure of clay minerals remains in all chemically treated samples when cured at 600°C in air, but it does not remain when cured at the same temperature in nitrogen. The intensive formation of hydrosodalite is mainly achieved through hydrothermal treatment, along with a primary treatment using 10M NaOH. Considering the calculated size of the crystallites, treatment with 6M NaOH and curing at 120°C can also be seen as beneficial for hydrosodalite formation.

The results of a study of the processes of formation of macro- and micro-inhomogeneity of ingots and rolled sheets are presented. To study the nature and sources of surface defects in rolled sheets, a comparative method of structural-concentration analysis of metal at the end-to-end metallurgical process of ingot - slab - sheet metal has been developed, based on the metallographic method of studying the structure and qualitative analysis of non-metallic inclusions. The research results showed that the quality of the surface of rolled sheets is determined mainly by the physical heterogeneity of the crust zone of the ingots, and the internal defects of thin rolled sheets largely depend on the contamination of the metal with non-metallic inclusions and off-axis segregation. A mechanism for transforming defects in the casting cortical zone into surface and internal defects in rolled sheets is proposed.

Human serum albumin (HSA) corona formation at polymer microparticles of a spheroidal shape was studied using dynamic light scattering and laser Doppler velocimetry (LDV). Physicochemical characteristics of the albumin comprising, the zeta potential and the isoelectric point were determined as a function of pH for various ionic strengths. Analogous characteristics of the polymer particles were carried out. The adsorption of albumin on the particles was monitored by electrophoretic mobility measurements (LDV). The stability of the HSA functionalized particle suspensions under various pHs and their electrokinetic properties were determined. The deposition kinetics of the particles on mica, silica and gold sensors were determined in situ by optical microscopy, AFM and by the quartz microbalance (QCM) under diffusion and flow conditions. The obtained results were interpreted in terms of the coarse-grained random sequential adsorption model that allowed to estimate the range of applicability of QCM for determining deposition kinetics of virus and bacteria at abiotic surfaces.

Post-mortem characterisation is a pivotal tool to trace back to the origin of structural failures in modern engineering analyses. This work presents a comparison of both the crack propagation profiles and the rupture roughness profiles based on areal parameters for total fracture area. Notched and smooth samples made of weather-resistant structural steel (10HNAP), popular S355J2 structural steel and aluminium alloy AA2017A under bending, torsion, and combined bending-torsion are investigated. After the fatigue tests, fatigue fractures are measured with an optical profilometer, and the relevant surface parameters are critically compared. The results show a great impact of the loading scenario on both the local profiles and the total fracture areas. In this work, the results of both approaches (local and total fracture zones) for specimens with different geometries are investigated. For all specimens, measured texture parameters decreased in the following order: total area, rupture area, and propagation area.

The surface defects of shield subway tunnel can significantly affect the serviceability of the tunnel structure and may compromise the operation safety. To effectively detect the multiple surface defects, this research employs a tunnel inspection trolley (TIT) based on the mobile laser scanning technique. By conducting the inspection of the shield tunnel on a metro line section, various surface defects are identified by the TIT, including water leakage defect, dislocation, spalling, cross-section deformation, etc. To explore the root causes of the surface defects, the association rules between different defects are calculated via an improved Apriori algorithm. Results show that: i) there are significant differences in different association rules of various surface defects of the shield tunnel; ii) the average confidence of the association rule “dislocation & spalling → water leakage” is as high as 57.78%, indicating that most of the water leakage defects are caused by dislocation and spalling of the shield tunnel in the sections being inspected; iii) the weakest rule appears at “water leakage → spalling”, with the average confidence of 13%. The association analysis can be used in predicting the critical defects influencing the structural reliability and operation safety, such as water leakage, and optimizing the construction and maintenance work for the shield subway tunnel.

Reactions of quinones with compounds containing an amino group can produce a wide variety of addition or substitution products that depend on reactivity of both quinone and amino derivative. 6,7-Dichloropyrido[1,2-a]benzimidazole-8,9-diones undergo selective nucleophilic substitution reaction with different benzohydrazides and α-hydroxy-p-quinone imine derivatives stabilized by strong intramolecular hydrogen bond were isolated. Synthesized compounds represent a combination of several structural motifs: benzimidazole core fused with α-hydroxy-p-quinone imine which contains a benzamido fragment. The protonation/deprotonation processes were investigated in a solution using UV-Vis spectroscopy and 1H NMR titration experiment. X-ray crystallography analysis revealed a set of weak non-covalent interactions such as intra- and intermolecular hydrogen bonds and π-π stacking. Additionally, the redox behavior of 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione and its p-imino derivative was investigated in acidic and neutral environment using cyclic voltammetry measurements. Cathode material based on 6,7-dichloropyrido[1,2-a]benzimidazole-8,9-dione could act as potential effective active electrode in aqueous electrolyte batteries, however further optimization is required.

This study aimed to develop multifunctional nanoplatforms for both cancer imaging and therapy using superparamagnetic iron oxide nanoparticles (SPIONs). Two distinct synthetic methods, reduction-precipitation (MR/P) and co-precipitation at controlled pH (MpH), were explored, including the assessment of coating’s influence, namely dextran and gold, on their magnetic properties. These SPIONs were further functionalized with gadolinium to act as dual T1/T2 contrast agents for magnetic resonance imaging (MRI). Parameters such as size, stability, morphology, and magnetic behavior were evaluated by a detailed characterization analysis. To assess their efficacy in imaging and therapy, relaxivity and hyperthermia experiments were performed, respectively. The results revealed that both synthetic methods lead to SPIONs with similar average, 9 nm. Mössbauer spectroscopy indicated that samples obtained from MR/P consist of approximately 11-13% of Fe present in magnetite, while samples obtained from MpH have higher content, of 33%-45%. Despite coating and functionalization, all samples exhibited superparamagnetic behavior at room temperature. Hyperthermia experiments showed increased SAR values with higher magnetic field intensity and frequency. Moreover, the relaxivity studies suggested potential dual T1/T2 contrast agent capabilities for the coated SPpH-Dx-Au-Gd sample, thus demonstrating its potential in cancer diagnosis.

KLEPTOSE® CRYSMEB is a methylated cyclodextrin derivative displaying less methylated group substitution than randomly methylated cyclodextrin. It has demonstrated an impact on atherosclerosis and neurological diseases. linked in part to cholesterol complexation and immune response, but the impact on inflammatory cascade pathways was not clear. Thus, the impact of KLEPTOSE® CRYSMEB on various pharmacological targets was assessed using human umbilical vein endothelial cells in physiological and inflammatory conditions, followed by screening against twelve human primary cell-based systems designed to model complex human tissue and disease biology of the vasculature, skin, lung, and inflammatory tissues using the BioMAP® Diversity PLUS® Panel. Finally, the anti-inflammatory mechanism was investigated on peripheral blood mononuclear cells to evaluate anti-inflammatory or pro-resolving properties. The results showed that KLEPTOSE® CRYSMEB can modulate the immune system in vitro and potentially manage vascular issues by stimulating the expression of molecules involved in the crosstalk between immune cells and other cell types. It showed anti-inflammatory effects driven by pro-inflammatory cytokine secretion inhibition and could have different impacts on different tissue types. Moreover, this cyclodextrin showed no clear impact on pro-resolving lipid mediators. Finally, it appeared that the mechanism of action of KLEPTOSE® CRYSMEB seems to not be shared by well-known anti-inflammatory molecules.

Polarimetry is used to determine the Stokes parameters of a laser beam. Once all four S0,1,2,3 parameters are determined, the state of polarisation is established. Upon reflection of a laser beam with the defined S polarisation state, the directly measured S parameters can be used to determine the optical properties of the surface, which modified the S-state upon reflection. Here, we demonstrate polarimetry for the determination of surface anisotropies related to birefringence and dichroism from different materials, which have a common feature of linear patterns of different alignments and scales. It is shown that polarimetry in the back-reflected light is complementary to ellipsometry and four-polarisation camera imaging.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

As urbanization continues to increase, key conservation areas like World Heritage sites are being altered. This transformation is a cause for concern as it threatens the Outstanding Universal Value of these sites. To address this issue, a research question was formulated: How urban is World Heritage? The research focused on identifying and monitoring urbanization in heritage core zones listed on the World Heritage by tracking changes in built-up areas from 1985 to 2015. The findings revealed that urban developments, including housing, transport infrastructure construction, visitor accommodation facilities, and land conversions, have significantly impacted heritage properties. More than a third (37\%, 426) of the cultural heritage properties reported urban development, with the highest occurrences in Europe, North America, Asia, and the Pacific. Furthermore, these regions also displayed the highest rate of change per year between 1985 and 2015. This indicates the urgent need to identify and monitor the urbanization of World Heritage to preserve their OUV amidst increasing urban development.

Within the task of replacing bronze journal bearings with aluminum the processes taking part on friction surface of high-alloyed aluminum alloys working with steel are investigated. The surface and subsurface layer of experimental aluminum bearings were studied before and after tribological tests by scanning electron microscopy including energy-dispersive analysis. Both structural and composition changes in surface layer are shown. It has been revealed that secondary structures are formed on the surface during friction process and include all the chemical elements of the tribosystem which is a consequence of its self-organization. The interaction behavior of some chemical elements of tribological system is discussed.

Laser machining by ultra-short (sub-ps) pulses at high intensity offers high precision, high throughput in terms of area or volume per unit time, and flexibility to adapt processing protocols to different materials on the same workpiece. Here we consider the challenge of optimization for high throughput: how to use the maximum available laser power and larger focal spots for larger ablation volumes by implementing a fast scan. This implies the use of high-intensity pulses approaching ∼PW/cm2 at the threshold where tunnelling ionization starts to contribute to overall ionization. A custom laser micromachining setup was developed and built to enable high speed, large area processing and easy system reconfiguration for different tasks. The main components include laser, stages, scanners, control system, and software. Machining of metals such as Cu, Al, or stainless steel, and fused silica surfaces at high-fluence and high-exposure doses at high scan speeds up to 3 m/s were tested for the fluence scaling of ablation volume, which was found to be linear. Modified surfaces are color-classified for their appearance, which is dependent on surface roughness and chemical modification. Such colour-coding can be used as a feedback parameter for industrial process control.

The modulation instability of surface capillary-gravity water waves is analysed in a shear flow model with a tangential discontinuity of velocity. It is assumed that air blows along the surface of the water with a uniform profile in the vertical direction. Such a model, despite its simplicity, plays an important role in hydrodynamics as the reference model for investigating basic physical phenomena of wave-current interactions and acquiring insights into a series of complex phenomena. In certain cases where the wavelength of interfacial perturbations is much bigger than the width of the shear fow profile, the model with the tangential discontinuity in the velocity is adequate for describing physical phenomena at least within limited spatial and temporal frameworks. A detailed analysis of the air-flow conditions under which modulation instability sets in is presented. It is also shown that the interfacial waves are subject to dissipative or radiative instability when negativeenergy waves appear at the interface.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

A method for accurately determining the chemical composition of deposits at the bottom of pores during the electrocoloring (e-coloring) of aluminum anodic oxide (AAO) layers in tin-based solutions is developed. The aluminum samples were AC e-colored after DC sulfuric anodization. Free-standing, tin e-colored aluminum oxide film was obtained by selective dissolution of the metallic aluminum from the AAO in copper chloride solution to access the deposit directly at the bottom of the pore. This allowed us to take XPS analysis directly from the deposits at pore bottoms without any interference from the base material or insulating barrier layer. The results revealed the presence of a mixture of tin oxide and metal in the deposits, which were richer in oxide content. Furthermore, a cyclic voltammetry experiment mimicking real polarization conditions during AC conditions was optimized and used to gain a deeper understanding of the electrochemical reactions that occur during AC electrocoloring. The comparison of CV results in tin-free and tin-containing electrolytes indicated that the tin deposited during a cathodic cycle is oxidized in the anodic cycle. The formation of tin based deposits radically changed the CV behavior. The XPS and cyclic voltammetry results consistently show that the deposits formed during e-coloring comprised a mixture of metallic and oxidic tin species richer in oxide content.

In the current industrial revolution, advanced technologies and methods can be effectively utilized for the detection and verification of defects in high-speed steel filament production. This paper introduces an innovative methodology for the precise detection and verification of micro surface defects found in steel filaments through the application of the Eddy current principle. Permanent magnets are employed to generates a magnetic field with high frequency surrounding a coil of sensor positioned at the filament's output end. The sensor's capacity to detect defects is validated through a meticulous rewinding process, followed by a thorough analysis involving scanning electron microscopy (SEM) and energy-dispersive spectroscopy (EDS). Artificial defects were intentionally introduced into a sample, and their amplitudes were monitored to establish a threshold value. The amplitude signal of these created defect was identified at approximately 10% FSH, which corresponds to a crack depth of about 20 µm. In the experimental production of 182 samples covering 38 km, the defect ratio was notably high, standing at 26.37%. These defects appeared randomly along the length of the samples. The verification results underscore the exceptional precision achieved in the detection of micro surface defects within steel filaments. These defects were primarily characterized by longitudinal scratches and inclusions containing physical tungsten carbide.

One of the relevant goals in forging technologies is simplifying the existing process and developing new processes that can retain the original or very close to the original dimensions and billet shape after the end of the deformation cycle. This study attempts to develop a forging equipment design that provides alternating cyclic loading; the alternate cyclic forging (ACF) method is proposed. To preliminary evaluate the ACF and study the plastic deformation behavior, numerical simulation via finite element modeling (FEM) was conducted using DEFORM-3D. The main attention was paid to the metal flow characteristics, effective strain and stress distribution, and the forging load. The ACF results in non-uniform metal flow with the formation of diagonal and vortex flows were demonstrated. Maximum effective strains and stresses zones are localized at two points of the billet contact with the surface of the tooling container and at two points of the interface between the punches. It was also assumed that reducing the contact area between the punch and the billet using separate semi-cylindrical punches can reduce the forging load. Preliminary finite element analysis (FEA) results of the proposed process after four successive steps of the deformation cycle confirmed the feasibility of its general implementation.

This article discusses the application of thermal quality control methods for plant tissues. The purpose of the work is to determine the optimal parameters of thermal impact on a spherical-shaped plant control object, ensuring the detection of surface and subsurface defects. The authors of the work proposed mathematical models of the temperature field for a spherical body with defects and a flat sample when exposed to the thermal influence of a pulsed source. As a result of the use of mathematical models, the thermophysical characteristics of plant tissues of varying degrees of disease damage were obtained, which made it possible to simulate the temperature field of the control object and obtain an image of classified tissues. The developed recommendations made it possible to select the optimal parameters of the thermal effect on the test object.

In order to enhance the efficiency and combined performances of nitriding layer, aluminum-modified plasma nitriding (Al-PN) was developed in this research by adding some FeAl particles around the samples during plasma nitriding (PN) for 42CrMo steel. The results show that the efficiency is dramatically enhanced almost 6 times comparing with traditional PN, with the effective hardening layer increasing from 224 μm to 1246 μm at 520℃/4h. More importantly, the compound layer increased just a little bit from 11.64 μm to 14.32 μm, which remarkably reduces the ratio of the compound layer thickness to effective hardening layer thickness, thus being quite beneficial to decrease the brittleness level, making the brittleness level decreasing from Level 4 to Level 1. Meanwhile, ultra-high surface hardness and excellent wear behaviors are obtained by aluminum-modified plasma nitriding (Al-PN) due to the formation of dispersed strengthening phased of AlN and FexAl in the nitriding layer, with the surface hardness increasing from 755 HV0.025 to 1251 HV0.025, wear rate decreasing from 8.15 x10-5g N-1 m-1 to 4.07 x10-5g N-1 m-1. In other words, comparing with PN, the wear resistance has been almost doubled by Al-PN. Therefore, the research can provide comprehensive insights into the surface characteristics and combined performances of the aluminum-modified plasma nitriding layer.

Background and Objectives: Most of the research of the BRCA1 inactivation is focused on monoallelic germline alterations and loss of heterozygosity in tumour. The aim of this study was to identify characteristic transcriptomic pattern of monoallelic somatic BRCA1 inactivation and estimate its impact to the event-free breast cancer survival prognosis. Materials and Methods: We conducted global transcriptome sequencing of breast cancer tissue samples to identify differentially expressed genes and signalling pathways associated with monoallelic somatic BRCA1 inactivation. The study group involved 36 patient samples categorized based on BRCA1 inactivation status. Subsequently, the differential gene expression and Kaplan-Meier analyses in the groups with and without monoallelic somatic BRCA1 inactivation were performed. Results: Kaplan-Meier analysis showed tendency for longer event-free survival in patients with monoallelic somatic BRCA1 inactivation, suggesting somatic BRCA1 inactivation is favourable prognostic. Differential gene expression analysis followed by the STRING tool enrichment analysis showed significant enrichment of proteins in the extracellular region and extracellular space. Conclusion: In this study we identified transcriptomic profile of differentially expressed genes TPSD1, FABP4, CARTPT and MMP9 as indicative for homologous recombination impaired tumours with tendency for better therapy results.

7046 aluminum alloy has good fatigue property, corrosion resistance and weld property, but the moderate strength and plasticity limit its wider application and development. In the present study, severe plastic deformation (SPD) was applied prior to T6 treatment to significantly strengthen and toughen the 7046 aluminum alloy. Results indicate that the alloy processed by 4 passes of equal channel angular pressing (ECAP) at 300 ℃ prior to T6 treatment exhibits an excellent mechanical performance, with ultimate tensile strength (UTS) and elongation (EL) of 485 MPa and 19%, exhibiting an improvement of 18.6% and 375% compared to that of the T6 alloy, respectively. The mechanical properties of the alloy are further improved by the additional room temperature (RT) rolling process, with UTS of 508 MPa and EL of 23.4%. There are more precipitates of η' and Al6Mn phases in the 300℃4P-R80%-T6 and 300°C4P-T6 alloys, which contribute to the strengthening and toughening enhancement by SPD processed T6 alloy. The results of this work may shed some light on enhancing 7046 aluminum alloy.

The unique structure of G4.0 PAMAM dendrimers allows the drug to be enclosed in internal spaces or immobilized on the surface. In the conducted research, the conditions for the formation of the active G4.0 PAMAM complex with doxorubicin (DOX) were optimized. The physicochemical properties of the system were monitored using DLS, CD, and fluorescence spectroscopy. The QCM-D method was chosen to determine the preferential conditions for the complex formation. The highest binding efficiency of the drug to the cationic dendrimer was observed under basic conditions when the DOX molecule was deprotonated. The decrease in the zeta potential of the complex confirms that DOX immobilizes through electrostatic interaction with the carrier's surface amine groups. The binding constants were determined from the fluorescence quenching of the DOX molecule in the presence of G4.0 PAMAM. The two-fold way of binding doxorubicin in the structure of dendrimers was visible in the ITC isotherm. Fluorescence spectra and release curves identified reversible binding of DOX to the nanocarrier. Among the selected cancer cells, the most promising anticancer activity of G4.0-DOX was observed in A375 malignant melanoma cells. Moreover, the preferred intracellular location of the complexes concerning the free drug was found, which is important from a therapeutic point of view.

This study investigated the relationship between aluminum adjuvant vaccines and the prevalence of 4 childhood diseases (Autism, Allergies, Asthma, ADD/ADHD) using data from the 2020-2021 National Survey of Children's Health (NSCH) [1] and the Centers for Disease Control National Immunization Survey (CDC NIS) [2]. The study found an association with aluminum adjuvant dosage and the prevalence of each disease studied (Autism, Allergies, Asthma, ADD/ADHD) through a weighted regression analysis of disease prevalence against the summed likelihood of aluminum adjuvant vaccine uptake.

To be CMOS-compatible, a low preparation temperature (< 500 °C) of ferroelectric films is required. In this study, BiFeO3 films were successfully fabricated at a low annealing temperature (< 450 °C) on aluminum foils by a metal-organic decomposition process. The annealing atmosphere on performance of BiFeO3 films was assessed at 440 ± 5℃. By replacing an O2-rich atmosphere with an N2-rich one, a better crystalline morphology was achieved in BiFeO3 films, resulting in better electric properties targeted for high-density ferroelectric random-access memory applications. These properties included a large remnant polarization (Pr~78.1 μC/cm2 @ 1165.2 kV/cm) and a high rectangularity (~91.3% @ 1165.2 kV/cm) of the P-E loop, along with excellent charge-retaining ability up to 1.0 × 103 s and a fatigue resistance reaching 1.0 × 109 switching cycles. The enhanced performance of BiFeO3 film in an N2-rich atmosphere maybe originated from the slightly high content of oxygen vacancies during the annealing process. Furthermore, decent electrical properties (Pr~70 μC/cm2 @ 1118.1 kV/cm) of the BiFeO3 films were achieved at a very low annealing temperature of 365 ±5 °C on aluminum foil substrates. These results offer a new idea for lowering the annealing temperature for integrated ferroelectrics in high-density FeRAM applications.

This study addresses the gap in methodological guidelines for Neuroergonomic attention assessment in safety-critical tasks, focusing on validating EEG indices including the Engagement Index (EI) and Beta/Alpha ratio alongside subjective ratings. A novel task-embedded reaction time paradigm was developed to evaluate the sensitivity of these metrics to dynamic attentional demands in a more naturalistic multitasking context. By manipulating attention levels through varying secondary tasks in the NASA MATB-II task while maintaining a consistent primary reaction-time task, the study successfully demonstrated the effectiveness of the paradigm. Results indicate that both Beta/Alpha ratio and EI are sensitive to changes in attentional demands, with Beta/Alpha being more responsive to dynamic variations in attention, and EI reflecting more the overall effort required to sustain performance, especially in conditions where maintaining attention is challenging. The potential for predicting the attention lapses through integration of performance metrics, EEG measures, and subjective assessments was demonstrated, providing a more nuanced understanding of dynamic fluctuations of attention in multitasking scenarios, mimicking those in real-world safety-critical tasks. These findings provide a foundation for advancing methods to accurately monitor attention fluctuations and mitigate risks in critical scenarios, such as train-driving or automated vehicle operation, where maintaining high attention level is crucial.

Patients with predominantly antibody deficiencies (PAD) display hypogammaglobulinemia with a high prevalence of infections, along with autoimmune manifestations, benign and malignant lymphoproliferation and granulomatous disease. It is noteworthy that PAD patients, even those with defects in the same causative genes display a variable clinical phenotype, suggesting that additional genetic polymorphisms, located in either immune-related or non-immune-related genes, may affect their clinical and laboratory phenotype. In this context, we analyzed 80 PAD patients, including 70 with common variable immunodeficiency (CVID) for SERPINA1 defects, in order to investigate their possible contribution to PAD clinical phenotype. Eight CVID patients carried heterozygous pathogenic SERPINA1 defects with normal alpha-1 antitrypsin levels. Interestingly, the presence of the Z allele (rs28929474) which was found in three patients, was significantly associated with liver disease; hepatic complications were also observed in patients carrying the p.Leu23Gln (rs1379209512) and the p.Phe76del (rs775982338) alleles. Conversely, no correlation of SERPINA1 defective variants with respiratory complications was observed, although patients with pathogenic variants exhibit a reduced probability of developing autoimmune diseases. Therefore, we recommend SERPINA1 genetic analysis in PAD, in order to identify patients with a higher risk for liver disease.

Vanilla planifolia is grown as a high-value orchid spice for its odor and savor attributes that increase due to the curing process associated with microbial colonization. This tends to influence the aromatic properties of vanilla. Hence, 11 Bacillus sp. strains were isolated from V. planifolia and identified with 16S rRNA gene sequencing. The liquid culture (1 mL of 107 CFU mL-1) of selected Bacillus vallismortis NR_104873.1:11-1518, B. velezensis ZN-S10, and B. tropicus KhEp-2 effectively fermented green-blanched vanilla pods kept at 10 ℃ during the sweating stage. GC-MS analysis showed that the methanol extract of non-coated, and B. vallismortis treated vanilla detected three (3) volatile compounds, whereas seven (7) components were obtained in B. tropicus and B. velezensis treatment. 4H-pyran-4-one, 2,3-dihydro-3,5-dihydroxy-6-methyl was found in B. velezensis ZN-S10, B. tropicus KhEp-2, B. vallismortis while it was not present in the control samples. This ketone compound suggested a Maillard reaction resulting in brown-increased aroma pods. Linoleic acid and Hexadecanoic acid ethyl esters were detected only in ZN-S10 strain-coated vanilla. A novel 3--Deoxy-d-mannoic lactone was detected only in B. vallismortis treated vanilla characterized as a new compound in V. planifolia which suggested that the new compound can be altered with the coating of bacteria in vanilla during fermentation. Thus, the Bacillus strains improved the volatile profile and exhibited a new aroma and flavor profile of vanilla owing to bacteria fermentation during the curing process.

Clinical and laboratory diagnostics are particularly important in monitoring the internal homeostasis of the body in high-yielding animals, especially in dairy cows, whose metabolism is under constant pressure to obtain high parameters of milk production and reproduction. Knowledge of laboratory test results and relationships based on significant correlations between various milk and blood parameters may be very useful in veterinary diagnostics and helpful in cattle practice in order to protect animal health and the quality of milk production. The aim of the study was to analyze the correlation between selected hematological biomarkers such as white blood corpuscles (WBC), red blood corpuscles (RBC), hemoglobin concentration (HGB), hematocrit (HCT), platelets (PLT), erythrocyte mean corpuscular volume (MCV), mean corpuscular hemoglobin content (MHC), mean corpuscular hemoglobin concentration (MCHC) and selected quantitative-qualitative parameters of cow’s milk such as current milk production, somatic cells count (SCC), colony of bacteria forming units (CFU), milk fat (MF), milk protein (MP), milk lactose (ML), milk solids (S), solids non-fat in milk (SNF), daily milk production. Samples were collected three times at daily intervals from 11 clinically healthy late-lactation dairy cows obtaining 33 sets of test results. This repeated study of cows allowed for obtaining a homogeneous group in order to determine statistical correlations between selected blood and milk parameters. Many significant correlations were found between the examined parameters. In cows, significant positive correlations were recorded between milk production and HGB, HCT, MCV or MHC. Significant negative correlations were also found between SCC and HGB, SCC and HCT, SNF and MCV, SNF and MHC, and between MF and RBC.

Aspalathin, a C-glucosyl dihydrochalcone, has previously been shown to protect cardiomyocytes against hyperglycemia-induced shifts in substrate preference and subsequent apoptosis. However, the precise gene regulatory network remains to be elucidated. To unravel the mechanism and provide insight into this supposition, the direct effect of aspalathin in an isolated cell-based system, without the influence of any variables, was tested using an H9c2 cardiomyocytes model. Cardiomyocytes were exposed to high glucose (33 mM) for 48 hours before post-treatment with or without aspalathin. Thereafter, RNA was extracted and RT2 PCR Profiler Arrays were used to profile the expression of 336 genes. Results showed that, 57 genes were differentially regulated in the high glucose or high glucose and aspalathin treated groups. STRING analysis revealed lipid metabolism and molecular transport as the biological processes altered after high glucose treatment, followed by inflammation and apoptosis. Aspalathin was able to modulate key regulators associated with lipid metabolism (Adipoq, Apob, Cd36, Cpt1, Pparγ, Srebf1/2, Scd1 and Vldlr), insulin resistance (Igf1, Akt1, Pde3 and Map2k1), inflammation (Il3, Il6, Jak2, Lepr, Socs3, and Tnf13) and apoptosis (Bcl2 and Chuk). Collectively, our results propose that aspalathin could reverse metabolic abnormalities by activating Adipoq while modulating the expression of Pparγ and Srebf1/2, decreasing inflammation via Il6/Jak2 pathway, which together with an observed increased expression of Bcl2 prevents myocardium apoptosis.

Purpose: The objective of the study was to qualitatively assess micro-gap dimensions, connecting fitting surface profile and bacterial leakage of machined and cast high gold alloy UCLA abutments, with or without electrodeposited gold coatings attached to external hexagon implants. Materials and methods: 16 plastic UCLA (PUCLA) and 5 machined cast-to UCLA (GUCLA) abutments were cast with a high gold content alloy. 10 were electrolytically gold plated (8 - PUCLA, 2 - GUCLA). All abutments were attached to implants giving 21 implant-abutment combinations (IACs). External perimeter micro-gaps measured with SEM under different illumination and magnification conditions were averaged over three regions. The IACs were examined for E.coli leakage following an initial sterility test. Disassembled combinations were examined with SEM and surface profiles qualitatively assessed. Results: External micro-gap measurements did not reflect the variable connecting surface profiles but average values < 3.5 μm were observed for all IACs. Bacterial transfer was observed in 3 of 5 PUCLA plated and 2 of 5 PUCLA non-plated IACs. No transfer occurred in the 3 GUCLA non-plated or 2 GUCLA plated IACs. Abutment connecting surfaces, both Au plated and not Au plated, showed plastic deformation (smearing) in variable mosaic patterns across the micro-gap. External micro-gap dimensions although not truly reflective of surface connecting profiles averaged < 3.5 μm measured under shadow eliminating silhouette illumination for both cast and pre-machined external hexagon abutments with and without Au plating. Conclusions: Micro-gap dimensions < 5 μm were obtained with both high noble metal cast and pre-machined external hexagon abutments with and without Au electrodeposited on the abutment connecting surface. Regions of intimate contact due to plastic deformation (smearing) of these surfaces was observed. A continuous smeared region around the circumference of the surfaces can provide an effective barrier to egress of E.coli bacteria from the internal regions of the implant under static loading.

.With the increasing use of carbon fiber reinforced plastics in various area, carbon fiber composites based on prepregs have attracted attention in industries and academia research. However, prepreg manufacturing processes are costly, and the strength of structures varies depending on the orientation and defects (pores and delamination). For non-contact evaluation of internal defects, we proposed lock-in infrared thermography to investigate orientation angles after a compression test. We also conducted a drop-weight impact test to study the behaviour of the composites after impact according the fibers orientation for composite fabricated using unidirectional carbon fiber prepregs. Using CAI tests, we determined the residual compressive strength and confirmed the damage modes using a thermal camera. The results of the drop weight impact tests show that the specimen laminated at 0° suffered the largest damage because of susceptibility of the resin to impact. In contrast, the specimens oriented in of 0°/90° and +45°/–45° directions transferred more than 90% of the impact energy back to the impactor because of the lamination of fibers in the orthogonal directions. Furthermore, the specimens that underwent complete damage in the impact tests were subjected to the lock-in method and showed internal delamination and cut fibers. With the finite elements analysis, the damage of each ply could be observed. Moreover, the temperature differences in the residual compression tests were not significant.

The Folla Redonda grape is indigenous to the region of Rias Bajas in Galicia, Spain. This grape is distinguished by its characteristic acid flavor and pulp of remarkable coloration. Despite the wine obtained from this grape is highly valued by consumers of this region for its surprising acidic notes and thickness, it is important to note that it is not a variety of Vitis vinifera and its production is not legally regulated. In the present study, an evaluation of the physicochemical properties of the Folla Redonda grape (pH, °Brix, °Bé, density, acidity, sugar content, etc.) as well as its content in bioactive compounds (total polyphenols and anthocyanins) was carried out. Additionally, the antioxidant potential of the extracts obtained from this grape was demonstrated. This study proved the interesting organoleptic characteristics of the grape, along with a high content of compounds of interest and an important antioxidant activity comparable to that of Vitis vinifera grapes. Therefore, the grape's natural consumption and its application in different industries such as nutraceutical or pharmacological would result in an important revaluation of the grape and significant health benefits. In case that the production of wine from this variety is legalized, consumers will not only be able to enjoy a wine with a characteristic dense reddish color and important acid tones, but also with interesting concentrations of bioactive compounds.

Axial resolution is one of the most important characteristics of a microscope. In all microscopes, a high axial resolution is desired in order to discriminate information efficiently along the longitudinal direction. However, when studying thick samples that do not contain laterally overlapping information, a low axial resolution is desirable as information from multiple planes can be recorded simultaneously from a single camera shot instead of plane-by-plane mechanical refocusing. In this study, we increased the focal depth of an infrared microscope non-invasively by introducing a binary axicon fabricated on barium fluoride substrate close to the sample. Preliminary results of imaging thick and sparse silk fibers showed an improved focal depth with a slight decrease in lateral resolution and increase in background noise.

Ménière's disease (MD) has an unclear cause. The microvascular dysregulation of the inner ear has been increasingly pointed as a potential contributor. This study investigates the prevalence of cardiovascular risk factors (CVRFs) in MD patients compared to those with posterior circulation cerebral infarction (POCI). CVRFs like hypertension, diabetes, dyslipidemia, obesity, coronary heart disease, and smoking were assessed in both MD and POCI patients. Brain MRI identified POCI etiology as "small vessel occlusion" (SVO) or "other etiology" (OE). The study included 64 MD and 84 POCI patients. Compared to MD, POCI OE showed a higher prevalence of CVRFs across various age groups, including hypertension, diabetes, dyslipidemia, and smoking. Notably, the odds of having POCI OE were significantly higher for individuals with hypertension and smoking. On the other hand, POCI SVO showed similar prevalence of CVRFs compared to MD. This study reveals no significant difference in CVRF prevalence between MD and smaller vessel POCI. However, a clear distinction emerges when comparing MD to POCI with involvement of larger blood vessels. Further research is needed to confirm these findings and explore potential shared risk factors between POCI (SVO) and MD.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Damaged connective tissues between the bone and tendons or ligaments are common among adults regardless of activity level. Achilles tendinosis is one of the most common tissue defects and enthesopathies. The patient in this study is a 54-year-old female with chronic Achilles tendinosis from chronic enthesopathy at the Achilles tendon insertion with a retrocalcaneal exostosis for three years who has failed standard-of-care practices for over two years. The patient received extracorporeal pulsed-activated therapy (EPAT) before applying 2ml of CryoText, a Wharton’s jelly tissue allograft. The patient then received class IV laser therapy treatments twice weekly for three weeks. The patient started with a 10/10 VAS at the initial visit. At five weeks post-application, the patient’s score had improved by 80% at 2/10 VAS. By week 13, the patient rated her pain as 0/10 VAS. The improvement in patient-reported pain and functionality reported in this study after the application of Wharton’s Jelly, EPAT, and class IV laser therapy warrants future research studying the safety and efficacy of these patient care modalities together.

Sulfate, the main dissolved contaminant in acid mine drainage (AMD), is ubiquitous in watersheds affected by coal and metal mining operations worldwide. Engineered passive bioremediation systems (PBS) are low-cost technologies that remediate sulfate contamination by promoting (1) precipitation of sulfate-bearing compounds, such as schwertmannite and gypsum; and (2) microbially-mediated sulfate reduction (BSR) to sulfide with subsequent precipitation of sulfide minerals. In this study, chemical and sulfur isotopic data are used to infer multiple pathways for sulfate sequestration in the Tab-Simco PBS. By simultaneously monitoring sulfate concentrations and δ34SSO4 values at four sampling points across the PBS, we (1) identified that the organic layer within the bioreactor was the primary site of BSR processes contributing to sulfate sequestration; (2) observed seasonal variations of BSR processes; (3) estimated that initially the BSR processes contributed up to 30% to sulfate sequestration in the Tab-Simco bioreactor; and (4) determined that BSR contribution to sulfate sequestration continuously declined over the PBS operational lifetime. Together, our results highlight the utility of combining geochemical and microbial fingerprinting techniques to decipher complementary processes involved in sulfur cycling in a PBS as well as the value of adding the sulfur isotope approach as an essential tool to help understand, predict, prevent and mitigate sulfate contamination in AMD-impacted systems.

Introduction: Intraductal papillary mucinous neoplasms (IPMN) are commonly-detected pancreatic cysts that may transform into pancreatic ductal adenocarcinoma (PDAC). Predicting which IPMNs will progress to PDAC remains a clinical challenge. Moreover, identifying those clinically evident IPMNs for which a surveillance approach is best is a dire clinical need. Therefore, we aimed to identify molecular signatures that distinguished between PDAC with and without clinical evidence of a IPMN to identify novel molecular pathways related to IPMN-derived PDAC that could help guide biomarker development. Methods: Data from the Oncology Research Information Exchange Network (ORIEN) multi-institute sequencing project was utilized to analyze 66 PDAC cases from Moffitt Cancer Center and The Ohio State University Wexner Medical Center for which tumor whole transcriptome sequencing datasets were generated. Cases were classified based on whether a tumor had originated from an IPMN (n=16) or presumably through the pancreatic intraepithelial neoplasia (PanIN) pathway (n=50). We then performed differential expression and pathway analysis using Gene-Set Enrichment Analysis (GSEA) and Pathway Analysis with Downweighted Genes (PADOG) algorithms. We also analyzed immune profiles using the Tumor-immune Microenvironment Deconvolution Web-portal for Bulk Transcriptomics (TIMEx). Results: Both GSEA and TIMEx indicate that PanIN-derived PDAC tumors enrich inflammatory pathways (complement, hedgehog signaling, coagulation, inflammatory response, apical surface, IL-2/STAT5, IL-6/STAT3, EMT, KRAS signaling, apical junction, IFN-gamma, allograft rejection) and are comparatively richer in almost all immune cell types than those from IPMN-derived PDAC upon deconvolution. IPMN-derived tumors were enriched in metabolic and energy generating pathways (oxidative phosphorylation, unfolded protein response, pancreas beta cells, adipogenesis, fatty acid metabolism, protein secretion). Further, the metabolic-linked gene signature enriched in the IPMNderived samples is associated with a cluster of early stage and long survival (top 4th quartile) PDAC cases from the Cancer Genome Atlas (TCGA) expression database. Intriguingly, the gene most significantly upregulated for both the improved survival group and IPMN-derived PDAC was gastrokine-2 (GKN2, padj<0.001), a gene upregulated in PDAC precursor lesions (compared to PDAC). Conclusions: Our data suggest that IPMN-derived and PanIN-derived PDACs differ in the expression of immune profiles and metabolic pathways. These initial findings support future studies to assess the accuracy of identifying PDACs arising from IPMN lesions based on either GKN2 expression or their metabolic or immune profiles and explore mechanisms to explain these findings.

Researchers have explored primary colour-geometric shape associations since Kandinsky's correspondence theory. However, there is a gap in the literature regarding interior colour applications on surface shapes. To address this gap, an online study was employed to gather data with one hundred participants who were asked to choose their preferred colours for shapes on bedroom walls with follow-up questions on the colour-shape semantic associations, their preference of colours and shapes on bedroom walls independently in addition to their favourite colour, their favourite shape, and colour-shape pairs without interior context. The results revealed that colour-shape preferences in interiors differ from those found in psychology studies, other colour applications on bedroom walls, and other preferences, indicating that colour preference is context-dependent. Interestingly, the most popular colour for surface shapes on bedroom walls is purple, followed by brown and blue. The study contributes to the existing literature by providing colour charts for bedroom applications for professionals in the industry, their clients/users, and future studies.

Accurate measurement of pedaling kinetics and kinematics is vital for optimizing rehabilitation, exercise training, and understanding musculoskeletal biomechanics. Pedal reaction force, the main external force in cycling, is essential for musculoskeletal modeling and closely correlates with lower limb muscle activity and joint reaction forces. However, sensor instrumentation like 3-axis pedal force sensors is costly and requires extensive post-processing. Recent advancements in machine learning (ML), particularly neural network (NN) models, provide promising solutions for kinetic analyses. In this study, an NN model was developed to predict radial and mediolateral forces, providing a low-cost solution to study pedaling biomechanics with stationary cycling ergometers. Fifteen healthy individuals performed a 2-minute pedaling task at two different self-selected (58±5 rpm) and higher (72±7 rpm) cadences. Pedal forces were recorded using a 3-axis force system. The dataset included pedal force, crank angle, cadence, power, and participants' weight and height. The NN model achieved an inter-subject normalized root mean square error (nRMSE) of 0.15±0.02 and 0.26±0.05 for radial and mediolateral forces at high cadence, respectively, and 0.20±0.04 and 0.22±0.04 at self-selected cadence. The NN model's low computational time suits real-time pedal force predictions, matching the accuracy of previous ML algorithms for estimating ground reaction forces in gait.

Alzheimer’s disease (AD) and the therapies of AD with anti-amyloid1-42 (Aβ) monoclonal antibodies are associated with the vascular complications of brain edema, hemorrhage, and cerebral amyloid angiopathy (CAA) termed amyloid-related imaging abnormalities (ARIAs). The neuropathology of normal and AD brains demonstrates that monocyte/macrophages (MMs) are critical in successful brain clearance in healthy brain by up-loading, transporting, and degrading Aβ but fail degradation and clearance in AD patients by releasing Aβ into vessels at the blood-brain barrier, causing vasculitis and ARIAs. The naturally-formed epoxides (EpFAs) of polyunsaturated fatty acids (PUFA’s), including arachidonic, docosahexaenoic, and eicosapentaenoic fatty acids, may repair degradation of Aβ by regulating Aβ-degrading enzymes, inflammatory cytokines, and unfolded protein response (UPR) to endoplasmic reticulum stress in a homeostatic fashion. EpFAs are, however, degraded by the soluble epoxide hydrolase enzyme (sEH) but are protected by the sEH inhibitor (sEHI) TPPU. In the cultures of AD patients’ macrophages, TPPU with the epoxide EEQ, and the cGAS/STING inhibitor H-151 increased uptake of Aβ at 2 hours and degradation of Aβ at 24 hours. In conclusion, the soluble epoxide hydrolase inhibitor TPPU with omega-3 fatty acids and the cGAS/STING inhibitor H-151 increase Aβ uptake and degradation in macrophages of AD patients, and potentially enhancing Aβ clearance in the AD brain.

High-precision conical threads are widely used in responsible joints in the drilling of oil and gas wells. Difficult underground drilling conditions due to the occurrence of significant mechanical loads and an aggressive environment in wells require the use of workable materials that are often difficult to machine. The huge need for such connections dictates the use of high-performance cutting tools, which means that high demands are placed on their effective geometric performance. The study describes the theoretical dependence of the profile precision of the tapered drill-string tool-joint threads of all standard sizes on the complex of a cutting tool geometric parameters and cutting tool setting accuracy. The experiments include an assessment of the geometric accuracy of the profile of the obtained NC23 thread connector, depending on the values of the installation angles and the declared tangential displacement of the standard threaded carbide insert.

The amount of solar energy produced is directly proportional to the surface area of solar panels exposed to sun rays. To increase the productivity of solar panels, a number of techniques are proposed by curving the surface or protruding the panel surface to maximise the surface area, e.g. Protruding panel surfaces with shapes such as pyramidal, cone, spherical cap, sinusoidal wavy curve, etc. These techniques are analysed to determine whether the panel surface area increases. The geometrical design analysis showed that, depending on the chosen surface curving method, the panel can achieve a remarkable increase in surface area.The system advisor model was used to assess a sample of solar cells with standard measurements of 6 by 6 inches that were organised in a zigzag pattern with different angles of inclination (10°, 15°, 20°, 25°, 30°, and 35°). Overall, the maximum power pump and annual AC energy performance increase by 1.4%, 4.2%, 6.8%, 10.8%, 14.9%, and 21.6%, respectively, over a one-year period of productivity. However, by applying the concept of solar panel efficiency degradation due to tilting solar panels at an angle by Mamun et al. (2022), for each 5° increase in tilt angle beyond the ideal 10°, the efficiency decreases by approximately 0.76%. In conclusion, the overall efficiency is greater than that of standard flat solar panels, provided the tilt angle is within a reasonable range.

Although vitamin D deficiency has been correlated with an increased risk of cardiovascular disease (CVD), there are few data on the association between 25-hydroxyvitamin D (25(OH) D) and atherogenic indices predictive of CVD. This study aimed to investigate the relationship of vitamin D status with lipid profile and atherogenic indices in adult women in Morocco. Three hundred healthy women, aged 18 to 50 years, from Meknes were included. Fasting 25(OH) D and lipid concentrations were determined using a one-step electrochemiluminescence-based immunoassay and an enzymatic method, respectively. Atherogenic indices (Atherogenic index of plasma (AIP), non-HDL cholesterol (Non-HDL-C), Atherogenic coefficient (AC), Castelli risk indices I and II (CRI-I and II), and CHOLIndex (CI)) were calculated using conventional lipid parameters. Logistic regression models and operating characteristic curve (ROC) analysis were used to assess the relationship of the variables and estimate the threshold of 25(OH) D levels associated with high atherogenic indices. 25(OH) D below 20 ng/ml was significantly associated with an enhanced risk of hypertriglyceridemia and elevated values of AIP, AC, Non-HDL-C, and CRI-I with an OR (95% CI) of 4.904 (1.856-12.959); 3.637(2.149-6.158); 3.589(1.673-7.700); 2.074(1.215-3.540), and 2.481(1.481-4.123), respectively. According to ROC analysis, the likelihood of hypertriglyceridemia and high values of AIP, AC, Non-HDL-C, and CRI-I were associated with 25(OH)D thresholds ≤15.15 ng/ml, ≤ 17.5 ng/ml, ≤ 19.8 ng/ml, ≤ 20.1 ng/ml and ≤ 19.5 ng/ml, respectively, all p &lt; 0.01. Based on atherogenic indices, this study indicates that vitamin D below 20 ng/ml may increase the risk of cardiovascular disease in adult women. Additional health efforts are needed to raise awareness among women and healthcare providers in preventing and controlling cardiovascular risk factors.

Defect detection and identification from fruits and vegetables are particularly challenging for Indian agriculture. Defect Detection is a process to identify the defects or damages in vegetables and fruits, based on the shapes, colors and textures. The local market finds it difficult to cope with the defects and other infections in fruits and vegetables as quality evaluations and classification of vegetables and fruits have become tedious process. Recently, several approaches based on Image processing, Machine Learning and Artificial Intelligence methods have been proposed for the purpose of defect detection. On the basis of classifying the types of defects, related pathogens, and physical and morphological characteristics descriptors, we review the different approaches based on a corpus of 57 articles between 2016 and 2021. In the process of describing the defect analysis, steps from the target articles, algorithms, and methods including qualitative and quantitative evaluation are mainly summarized. The aim of this current review work is to present-day novel images and collects recent defective area calculation methods to detect surface defects of fruits and vegetables using RGB images and to classify whether the fruit is defected or fresh. A rigorous evaluation of many new algorithms provided for quality assurance by researcher’s probes of vegetables and fruits have been conducted in this work. This review work conveys that using the recent identification features will help to decrease the disadvantages in fruit storeroom owing to storage of the affected vegetables and fruits, ie. Preventing the spread of defects and other infections from the infected fruits and vegetables to the fresh ones.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

In the discussion on environmental policies, the notion of eco-efficiency is often used. Eco-efficiency is defined as the delivery of products and services with competitive values, while reducing the ecological impacts and satisfying human needs. In an environment of great competitiveness in which the companies operate, the improvements in the productive process is one of the differentiating factors for guaranteeing a strong competition. Also it is essential rationalizing energy consumption and natural resources. For this it is necessary to understand the main operations and dynamics of the company. This work presents an empirical study of a Portuguese company in the industrial sector. The problematic here presented is based on the company’s growing concern to reduce the amount of scrap produced. From the literature research that was performed, a strong dependence relation between the different variables in the extrusion process was found. The main objective of this work is to model the aluminium extrusion process, with the aim of minimizing the production of scrap. For this several variables involved in the process are taking into account. Using statistical techniques, in particular multiple linear regressions, it was possible to identify the importance of the variables under study for the scrap production.

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

Aluminum (Al) toxicity and low phosphorus availability (LP) are the top two co-existing edaphic constraints limiting agriculture productivity in acid soils. Plants have evolved versatile mechanisms to cope with the two stresses alone or simultaneously. However, the specific and common molecular mechanisms, especially those on flavonoids and carbohydrate metabolism, are still unclear. Laboratory studies were conducted on two wheat genotypes, Fielder (Al-tolerant and P-efficient) and Ardito (Al-sensitive and P-inefficient), exposed to 50 μM Al and 2 μM Pi (LP) in hydroponic solutions. After 4 days of stress, wheat roots were analyzed via transcriptomic and targeted metabolomic techniques. A total of 2296 differentially expressed genes (DEGs, 1535 up and 761 down) under Al and 3029 DEGs (1591 up and 1438 down) under LP were identified in Fielder. Similarly, 4404 DEGs (3191 up and 1213 down) under Al and 1430 DEGs (1176 up and 254 down) under LP were identified in Ardito. The GO annotation analysis results that 4079 DEGs annotated to the metabolic processes term. These DEGs were significantly enriched in the phenylpropanoid, flavonoid, flavone and flavonol biosynthesis, and carbohydrate metabolism pathways by performing the KEGG enrichment analysis. The targeted metabolome analysis detected 19 flavonoids and 15 carbohydrate components in Fielder and Ardito under Al and LP. More responsive genes and metabolites were involved in flavonoid metabolism under LP than Al in the Fielder, while an opposite trend in the Ardito. In the carbohydrate metabolism pathway, the genes and metabolites were higher in Fielder than in Ardito. The combined transcriptome and metabolome analysis revealed that the flavonoid and carbohydrate genes and metabolites differed between Fielder and Ardito under Al and LP, which may be an important reason for Fielder’s high Al and LP resistance. The results of this study lay a foundation for pyramiding genes and breeding multi-resistance varieties.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

Strip steel surface defect recognition research has important research significance in industrial production. Aiming at the problems of defect feature extraction difficulty, slow detection speed and insufficient dataset, YOLOv5 is improved on the basis of YOLOv5, and YOLO-LFPD (Lightweight fine particle detection) model is proposed. By introducing the RepVGG (Re-param VGG) module, the robustness of the model to the surface defect features of strip steel is enhanced, and the expressive ability of the model is improved. FasterNet is used to replace the backbone network, which ensures the accuracy and accelerates the inference speed, making the model more suitable for real-time monitoring. The use of pruning, GA genetic algorithm with OTA loss function method further reduces the model size while better learning the strip steel defect feature information, thus improving the generalisation ability and accuracy of the model. The experimental results show that the introduction of the RepVGG module and the use of FasterNet can well improve the model performance, with a reduction of 48% in the number of parameters, a reduction of 13% in the number of GFLOPs, an inference time of 77% of the original, and an optimal accuracy compared with the network models in recent years. The experimental results on the NEU-DET dataset show that the accuracy of YOLO-LFPD is improved by 3% to 81.2%, which is better than other models, and provides new ideas and references for the lightweight strip steel surface defect detection scenarios and application deployment.

The variation of aerosols, especially dust aerosol, in time and space plays an important role in climate forcing studies. Aerosols can effectively reduce land surface longwave emission and re-emit energy at a colder temperature, making estimation of downwelling surface longwave radiation (DSLR) with satellite data difficult. Using the latest atmospheric radiative transfer code (MODTRAN 5.0), we simulate the outgoing longwave radiation (OLR) and DSLR under different land surface and atmospheric profile conditions. The results show that dust aerosol has an obvious “warming” effect to longwave radiation compared with other aerosols, that aerosol longwave radiative forcing (ALRF) increased with increasing aerosol optical depth (AOD), and that the atmospheric water vapor content (WVC) is critical to the understanding of ALRF. A method is proposed to improve the accuracy of DSLR estimation from satellite data for the skies under heavy dust aerosols. The AOD and atmospheric WVC under cloud-free conditions with a relatively simple satellite-based radiation model that yields the high accurate DSLR under heavy dust aerosol are used explicitly as model input to reduce the effects of dust aerosol on the estimation of DSLR. Validations of the proposed model with satellites data and field measurements show that it estimates the DSLR accurately under heavy dust aerosol skies. The root mean square errors (RMSEs) are 20.4 W/M² and 24.2 W/M² for Terra and Aqua satellites, respectively, at the Yingke site, and the biases are 2.7 W/M² and 9.6 W/M², respectively. For the Arvaikheer site, the RMSEs are 23.2 W/M² and 19.8 W/M² for Terra and Aqua, respectively, and the biases are 7.8 W/M² and 10.5 W/M², respectively. The proposed method is especially applicable to acquire relatively high accurate DSLR under heavy dust aerosol using MODIS data with available WVC and AOD data.

Follicular helper CD4+ T cells (TFH) are a major cellular pool for the maintenance of HIV reservoir. Therefore, the delineation of the follicular (F)/germinal center (GC) immune landscape will significantly advance our understanding of HIV pathogenesis. We have applied multiplex confocal imaging, in combination with relevant computational tools, to investigate, F/GC in situ immune dynamics in viremic (vir-HIV), antiretroviral treated (cART HIV) People Living With HIV (PLWH) and compare them to reactive, non-infected controls. Lymph nodes (LNs) from viremic and cART PLWH could be further grouped based on their TFH cell densities in high-TFH and low-TFH subgroups. These subgroups were also characterized by different in situ distribution of PD1hi TFH cells. The significantly accumulated follicular, compared to extrafollicular, FOXP3hi CD4+ T cells found in the low-TFH cART-HIV group were characterized by a less scattered in situ distribution and strongly correlated with the cell density of CD8+ T cells in this group. An inverse correlation between plasma viral load and LN GrzBhiCD8+ T and CD16hiCD15lo cells was found. Our data reveal the complex GC immune landscaping in HIV infection and suggest that follicular FOXP3hi CD4+ T cells could be negative regulators of TFH cell prevalence in cART-HIV.

The structure and physicochemical properties of polyvinyl alcohol (PVA) and PVA/glycerol films have been investigated by Fourier-transform infrared spectroscopy (FT-IR), X-ray Diffraction (XRD), thermogravimetry/differential thermal analysis (TG/DTA), and advanced scanning probe microscopy (SPM). In the pure PVA films, SPM allowed us to observe ribbon-shaped domains with a different frictional and elastic contrast, which apparently originated from a correlated growth or assembly of PVA crystalline nuclei located within individual PVA clusters. The incorporation of 1.0 wt.% glycerol led to modification in shape of those domains from ribbon-like in pure PVA to rounded in PVA/glycerol 1.0 wt.% films; changes in the relative intensities of the XRD peaks and a decrease of the amorphous halo in the XRD pattern were also detected, while the DTA peak corresponding to the melting point remained at almost the same temperature. For higher glycerol content, FT-IR revealed additional glycerol-characteristic peaks presumably related to the formation of glycerol aggregates, and XRD, FT-IR, and DTA all indicated a reduction in crystallinity. For more than 2.0 wt.% glycerol, the plasticization of the films complicated the acquisition of SPM images without tip-induced surface modification. Our study contributes to the understanding of crystallinity in PVA and how it is altered by a plasticizer such as glycerol.

The surface velocity of the Amery Ice Shelf (AIS) is vital to assessing its stability and mass balance. Previous studies have shown that the AIS basin has a stable multi-year average surface velocity. However, spatiotemporal variations in the surface velocity of the AIS and the underlying physical mechanism remain poorly understood. This study combined offset tracking and DInSAR methods to extract the monthly average surface velocity of the AIS and obtained the inter-annual surface velocity from the ITS_LIVE product. An uneven spatial distribution in inter-annual variation of the surface velocity was observed between 2000–2022, although the magnitude of variation was small at less than 20.5 m/yr. The increase and decrease in surface velocity on the eastern and western-central sides of the AIS, respectively, could be attributed to the change in the thickness of the AIS. There was clear seasonal variation in monthly average surface velocity at the eastern side of the AIS between 2017–2021, which could be attributed to variations in the area and thickness of fast-ice and also to variations in ocean temperature. This study suggested that changes in fast-ice and ocean temperature are the main factors driving spatiotemporal variation in the surface velocity of the AIS.

Aluminum (Al), making up a third of the Earth's crust, is a widespread toxic contaminant, particularly in acidic soils. It impacts crops at multiple levels, from the cellular to the whole plant. This review delves into aluminum's reactivity, including its cellular transport, involvement in oxidative redox reactions, development of specific metabolites, and the influence of genes on the production of membrane channels and transporters, as well as its role in triggering apoptosis leading to senescence. It discusses the involvement of channel proteins in calcium influx, vacuolar proton pumping, the suppression of mitochondrial respiration, and the initiation of programmed cell death. At the cellular nucleus level, the effects of Al on gene regulation through alterations in nucleic acid modifications, such as methylation and histone acetylation, are examined. The review in addition outlines the pathways of Al induced metabolic disruption specifically citric acid metabolism, regulation of proton excretion, induction of specific transcription factors, modulation of Al-responsive proteins, changes of citrate and nucleotide glucose transporters and overall metal detoxification pathways in tolerant genotypes. It also considers the expression of phenolic oxidases in response to oxidative stress, their regulatory feedback on mitochondrial cytochrome proteins, and their consequences on root development. Ultimately, the review focuses on the selective metabolic pathways that facilitate Al exclusion and tolerance, emphasizing compartmentalization, antioxidative defense mechanisms, and the control of programmed cell death to manage metal toxicity.

It is very difficult to repair large bone defects, especially when they have a complex shape. We have developed a new technique to make a desired copy of rabbit bones. A rabbit distal femur was scanned by computed tomography (CT), and a rectangular-shaped beta-tricalcium phosphate (β-TCP) block with 75% porosity was automatically machined using milling tools into a half-scale copy of the distal femur based on the CT data. The β-TCP block was seeded with bone morphogenetic protein-2 and bone marrow cells obtained from the femur and implanted on the periosteum of the femur. At 10 weeks after implantation, most of the β-TCP block had been replaced by bone and a complete copy of the distal femur was reconstructed. Our findings indicate that this technique will be useful in the clinical setting. We also report the representative clinical results of treatment with β-TCP graft in patients with bone defects since 1989.

Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

Ice accumulation poses considerable challenges in transportation, notably in the domain of general aviation. The present study combines the strengths and limitations of conventional aircraft de-icing techniques with the emerging trend toward all-electric aircraft. The study aims to utilize laser-induced graphene (LIG) technology to create a multifunctional surface, seamlessly integrating hydrophobic properties with efficient electrical heating to mitigate surface icing effectively. We investigated the utilization of a 10.6 μm CO2 laser for direct writing on polyimide (PI), a widely-used insulating encapsulation material. From the thermomechanical perspective, our initial analysis using COMSOL Multiphysics software revealed that when the laser power P exceeds 5 W, the PI substrate experience ablative damage. The experimental results show that when P ≤ 5W, an increase in power has a positive impact on the quality, surface porosity, roughness reduction, line-spacing reduction, and water contact-angle enhancement of the graphene. Conversely, when P &gt; 5 W, higher power negatively affects both the substrate and the graphene structure by inducing excessive ablation. However, it influences the graphene line height positively and is consistent with overall experimental-simulation congruence. Furthermore, the incorporation of high-quality graphene resulted in a surface that exhibited higher contact angles (CA &gt; 120°), lower energy consumption, and higher heating efficiency compared to the use of traditional electrically heated materials for anti-icing applications. The potential applications of this one-step fabrication method extend across various industries, particularly aviation, marine engineering, and other ice-prone domains. Moreover, the method has extensive prospects for addressing pivotal challenges associated with ice formation and serves an innovative and efficient anti-icing technology.

Background/Objectives: Dengue is an arbovirus caused by a virus. It is an endemic infectious and occurs in warmer climates. It is not uncommon for the disease to be asymptomatic. However, the severe form can also be triggered and require intensive care. In this sense, patients present a wide variety of symptoms, which can trigger comorbidities such as arthritis, hematologic diseases, liver diseases, kidney diseases, autoimmune diseases, and, mainly, diabetes and hypertension. Among the symptoms, the presence of fever, myalgia, headache, nausea, vomiting, leukopenia, petechiae, retroorbital pain, arthralgia, rashes, skin eruptions, cardiovascular symptoms, respiratory symptoms and, depending on the severity, the presence of hemorrhages may occur. Methods: 235 patients' anonymized records from a secondary hospital were analyzed. Ethics approval was obtained and no patients’ consent was needed. Statistical analysis used frequency distributions and Chi-square tests, with SPSS software. Results: Similar to other studies, our results show that dengue can lead to complications. Furthermore, there was no significant difference in the distribution of the proportion of symptoms between patients with positive and negative serology. However, there was a significant association between age group and symptoms of fever and myalgia, with the occurrence of fever decreasing with increasing age and myalgia being more frequent in adults and less frequent in those &lt;10 years old. Conclusions: Dengue can lead to complications, with fever becoming less common and muscle pain increasing as people age. Climate change could spread dengue to new areas. To address this, we need better vaccines and more effective mosquito control.

Plasmonic sensors have great potential for widespread usage, but the prohibitive cost of noble metals restrains the wider adoption of this technology. The aim of our study is to develop a cost-effective Al-based alternative to plasmonic detectors commonly based on noble metals. We considered a structure that consists of a Si p-n junction with an overlying grating-relief aluminum layer. The investigation of the infrared plasmonic resonance dependency on the structure geometric parameters and optimization of the fabrication process allowed us to determine optimal parameters for photodetection enhancement. The resonance photoresponse of optimized aluminum-based plasmon-polariton photodetector was significantly improved and became comparable to noble metal-based analogs. Our results can be used for the creation of cost-effective high-sensitivity plasmonic sensors.

The samples from lunar farside have great significance for the study of the Moon, and even the solar system. Chang’e-6 landed successfully on the southern mare of the Apollo basin and returned ~2 kg samples from lunar farside. To provide a better understanding for the background of the returned samples, we conducted detailed crater size-frequency distribution (CSFD) measurements in the Chang’e-6 landing region, the southern mare of the Apollo basin. The southern mare is divided into western mare (W region) and eastern mare (E region), and then subdivided into five sub-units (W1, W2, W3, W4, W5) and three units (E1, E2, E3), respectively, according to the elevation, Ti and Fe abundances. Within the W2 and W5 region, more detailed sub-units were divided. The results show that the southern mare generally have two epochs, one of the Imbrian period and the other of the Eratothenian period. The basalt eruption lasted for ~1.7 Ga, from 3.28 Ga of the eastern mare to 1.54 Ga of the western mare. W region is younger than E region, while the three units of E region has an age of ~3.2 Ga. The ages of the western mare basalts range from 2.98 Ga to 1.54 Ga, lasting for 1.4 Ga. It’s worth noting that the age of the basalt at the Chang’e-6 sampling site is ~1.68 Ga, indicating the samples returned may include components with this very young age.

A special vibration damper is proposed for material property identification through a scratching process on a vibrating object. This paper presents the design and working principle of a scratching damper based on a scratch test device. A non-contact electromagnetic shaker is used to generate the shaking force for the vibration of the tested object. The required pressure on the scratched material during the scratching process is generated by a compression spring and adjusted by changing the amount of compression of the spring. The proposed damper is designed and tested on extruded aluminum samples for the determination of its Young’s modulus and hardness and validated by using the standard test instruments. Observations of physical dimensions of the scratching tracks are determined by microscope and were utilized to compute the scratching energy factor. Load curves are obtained at different pressure of the scratching process. The hysteresis loop energy during the scratching process of the tested object is measured and used for the determination of material properties of the object. Furthermore, energy conservation law, scratch energy release rate and loop energy release rate are used to determine the Young’s modulus and hardness of the sample. The measurement accuracy of the modulus and hardness of the tested sample is evaluated. The proposed method of material testing has several advantages over the traditional methods such as low cost and high repeatability, and may be used as an alternative to the standard modulus and hardness testers.

Etiological factors involved in myelodysplastic syndrome (MDS) include immunologic, oxidative stress, and inflammatory factors, among others, and these are targets for microRNAs (miRNs). Here, we evaluated whether some miRNs may affect the tumor development comparing untreated and 5-azacitidine (5-AZA) MDS-treated patients. Peripheral blood samples were collected from 20 controls and 24 MDS patients, and selected miRNs related to redox balance and inflammation, including miR-18a, miR-21, miR-34a and miR-146a, were isolated and measured by quantitative real-time polymerase chain reaction (qRTPCR). A differential expression profile of miRNs was detected in untreated MDS patients and 5-AZA group. MiR-18a, miR-21, miR-34a and miR-146a were significantly overexpressed in untreated MDS, compared to controls. However, we did not observe any miRNs profile alteration during the progression of the disease. On the other hand, 5-AZA treatment tends to restore miRNs expression levels. Relating to prognostic risk factors, high risk MDS groups (high IPSS-R, high cytogenetic risk, high molecular risk (HMR) mutations tended to be related with higher expression levels of miR-18a and miR-34a. Higher miRNs expression is correlated with lower glutathione peroxidase activity, while they are related with a higher profile of pro-inflammatory cytokines (IL-2, IL-6, IL-8, TNF-α). Although our study was limited by the low number of MDS patients included, we identified miRNs deregulation involved in the MDS development, that could regulate redox sensors and inflammatory responses. Finally, 5-AZA treatment is related with lower miRNs expression levels in MDS patients.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

The superconductivity of CaC6 as a function of pressure and of abundant Ca isotopes is revisited using DFT calculations on a 2c – double hexagonal superlattice. The introduction of superlattices is motivated by previous synchrotron absorption and Raman spectroscopy results on other superconductors that show evidence of superlattice vibrations at low (THz) frequencies. A 2c superlattice for CaC6 is illustrative of atomic orbital symmetry and periodicity, including bonding and antibonding s-orbital character implied by cosine modulated electronic bands. Inspection of the cosine band reveals that the cosine function has a small (meV) energy difference between bonding and antibonding regions relative to a midpoint non-bonding energy. Fermi surface nesting is apparent in an appropriately folded Fermi surface using a superlattice construct. Nesting relationships identify phonon vectors for conservation of energy and for phase coherency between coupled electrons at opposite sides of the Fermi surface. Detailed analysis of this Fermi surface nesting provides accurate estimates of the superconducting gaps for CaC6 with change in applied pressure. Recognition of superlattices within a rhombohedral or hexagonal representation provides consistent mechanistic insight on superconductivity and electron−phonon coupling in CaC6.

Assuming the Multiple Point Principle (MPP) as a new law of Nature, we considered the existence of the two degenerate vacua of the Universe: a) the first Electroweak (EW) vacuum at $v_1\approx 246$ GeV—“true vacuum”, and b) the second Planck scale “false vacuum” at $v_2 \sim 10^{18}$ GeV. In these vacua, we investigated different topological defects. The main aim of the paper is an investigation of the black-hole-hedgehogs configurations as defects of the false vacuum. In the framework of the $f(R)$ gravity, described by the Gravi-Weak unification model, we considered a black-hole solution, which corresponds to a “hedgehog”—global monopole, that has been “swallowed” by the black-hole with mass core $M_{BH}\sim 10^{18}$ GeV and radius $\delta\sim 10^{-21}$ GeV$^{-1}$. Considering the results of the hedgehog lattice theory in the framework of the $SU(2)$ Yang-Mills gauge-invariant theory with hedgehogs in the Wilson loops, we have used the critical value of temperature for the hedgehogs’ confinement phase ($T_c\sim 10^{18}$ GeV). This result gave us the possibility to conclude that the SM shows a new physics (with contributions of the $SU(2)$-triplet Higgs bosons) at the scale $\sim 10$ TeV. This theory predicts the stability of the EW-vacuum and the accuracy of the MPP.

Lap joints were friction stir welded in AA 7075-T6 at 1320 rpm and using two welding speeds: 70 mm/min and 120 mm/min. The temperature profiles of the weld zone were registered during the process; furthermore, the microhardness, tensile strength, and microstructure of the joints produced were examined. This study brings new insights into the thermomechanical behavior of the material during the process. The peak temperature obtained with the lower welding speed (70 mm/min) is 10% higher than that obtained with the higher speed (120 mm/min). Moreover, a 5% increase in microhardness and a 6% increase in tensile strength were were observed increasing the welding speed. Addition-ally, the microstructure examination demonstrated that, by decreasing the welding speed, the larger interaction between the tool and the material results in a deeper stir zone due to the increased heat diffusion downwards to the material. This heat flow affects the thermal profile and influences the resulting mechanical properties of the welded joints.

In the case of a Cu-Mo-W polymetallic ore, the wastewater from the scheelite cleaning flowsheet contains large amounts of residual flocculants and metal ions, and the separation of chalcopyrite and molybdenite require a large number of environmentally harmful depressants. Therefore, it is necessary to find new methods to reduce the environmental and cost pressures of wastewater treatment and the use of depressants. In this work, the flotation wastewater from scheelite cleaning flowsheet for the separation of chalcopyrite and molybdenite by selective surface passivation was investigated for the first time. Flotations of single minerals and artificially mixed minerals with or without immersion pretreatment in the presence and absence of aeration were performed. The results showed that pulp pH had no effect on the flotation of either mineral, and a molybdenite recovery of 93.22% with chalcopyrite recovery of 10.77% was achieved under the conditions of 10 days of immersion pretreatment with aeration, 350 mg/L of kerosene, and 100 mg/L of MIBC. By combining the electrochemical cyclic voltammetry analysis and characterization by XRD and SEM, the selective surface passivation mechanism of chalcopyrite was discussed, which could be due to the coverage of the insoluble oxidation products, especially jarosite. This work has simultaneously achieved the depressant-free flotation separation of molybdenite and chalcopyrite and the reuse of scheelite flotation wastewater, which is of great significance for environmental protection and cost saving.

We aimed to investigate the relationship between membrane material and development of membrane fouling in a membrane bioreactor (MBR) using membranes with different pore sizes and hydrophilicities. Batch filtration tests were performed using submerged single hollow fiber membrane ultrafiltration (UF) modules with different polymeric membrane materials including cellulose acetate (CA), polyethersulfone (PES), and polyvinylidene fluoride (PVDF) with activated sludge taken from a municipal wastewater treatment plant. The three UF hollow fiber membranes were prepared by a non-solvent-induced phase separation method and had similar water permeabilities and pore sizes. The results revealed that transmembrane pressure (TMP) increased more sharply for the hydrophobic PVDF membrane than for the hydrophilic CA membrane in batch filtration tests, even when membranes with similar permeabilities and pore sizes were used. PVDF hollow fiber membranes with smaller pores had greater fouling propensity than those with larger pores. In contrast, CA hollow fiber membranes showed good mitigation of membrane fouling regardless of pore size. The results obtained in this study suggest that the surface hydrophilicity and pore size of UF membranes clearly affect the fouling properties in MBR operation when using activated sludge.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

Background: Kidney damage is considered to be one of the risk factors for severity and mortality among COVID-19 patients. However, molecular nature of such observations remains unknown. Hypothesis: Altered gene expressions due to infection and in chronic kidney disease could explain severity in COVID-19 with kidney defects. Methods: We collected gene expression data from publicly available resources Gene Expression Omnibus CKD, Enrichr for deregulated genes in SARS-CoV infected cells in vitro, DisGeNET and others and carried out enrichment analysis using Enrichr. Result: Number of common genes altered in chronic kidney disease (CKD) and SARS-CoV infected cells was 2834. Enrichment analysis revealed that biological processes related viral life cycle and growth, cytokines, immunity, interferon, inflammation, apoptosis, autophagy, oxidative stress and others were significantly enriched with common deregulated genes. Similarly, significantly enriched pathways related to viral and bacterial infections, immunity and inflammation, cell cycle, ubiquitin mediated proteolysis, signaling pathways like Relaxin signaling pathway, mTOR signaling pathway, IL-17 signaling pathway, NF-kappa B signaling pathway were enriched with the common deregulated genes. These processes and pathways are known to be related to kidney damage. DisGeNET terms enriched include and related to Dengue fever, chronic Hepatitis, measles, retroviridae infections, respiratory syncytial virus Infections and many others. Kidney dysfunction related terms ischemia of kidney, renal fibrosis and diabetic nephropathy. Conclusion: Common deregulated genes in SARS-CoV infected cells and chronic kidney disease, as well as their enrichment with molecular processes and pathways relevant for viral pathogenesis and renal dysfunctions, could explain the severity of COVID-19 with kidney disease. This observation not only provides molecular relation of severity in COVID-19 with renal dysfunctions but might also help in the management and treatment targets for these cases.

Protrusive defects on the color filter of thin-film transistor (TFT) liquid crystal displays (LCDs) frequently damage the valuable photomask. An fast method using side-view illuminations associated with digital charge-couple devices (CCDs) to detect the protrusive defect in the four substrates, which are the black matrix (BM), red, green, and blue. Between the photomask and substrate, the depth of field (DOF) is normally 300 μm for the proximity-type aligner; we select the four substrates to evaluate the detectability in the task. The experiment is capable of detecting measurements of 300 μm and even lower than 100 μm can be assessed successfully. The maximum error of the measurement is within 6% among the four samples. Furthermore, the uncertainty analysis of three standard deviations is conducted. Thus, the method is cost-effective to prevent damage for valuable photomasks in the flat panel display industry.

Recycling solar panels is crucial to mitigating the environmental impact of the growing volume of end-of-life photovoltaic waste and conserving valuable resources, while achieving high purity in recovered materials ensures their effective reuse in the manufacturing of new solar panels, con-tributing to a sustainable and circular economy. This study proposes a two-step leaching process to recover Ag and Al from the silicon fraction of EoL photovoltaics (PVs). In the first stage laboratory scale tests, 99% Al was extracted using 5% HCl at room temperature for 3 hrs. The Al was precip-itated as oxide from the solution. The silicon residue was then leached with 0.5 M HNO3 at 80°C for 2 hrs extracting 99% Ag and producing Si with 99.83% purity. The silver was precipitated to produce metallic Ag with >99.9% purity. Methods to mitigate the effluent solutions were recom-mended and the entire process was presented in a flowsheet.

This study aimed to learn disturbance information to effectively control multiple small unmanned surface vehicles (USVs) for marine research purposes at sea. The learned disturbance information was used to investigate the control of multiple USV swarms based on the leading–following formation technique. Numerous studies have already been conducted on swarm control using drones in the air; however, there has been a paucity of studies on swarm control in the sea. Contrary to swarm control in aviation, the fluid density of the sea is high, and the environment is constantly changing; thus, a robot system would be significantly affected by disturbances. This ultimately influences the maintenance of swarm formations and the accomplishment of missions [1,2]. Therefore, it is difficult to control numerous moving objects while maintaining a formation at sea by using the existing aerial drone swarm control technology. To solve this problem, we learned a long short-term memory (LSTM) model with time-series marine environmental data to predict maritime disturbances. Thereafter, the model was applied to a mission-based position control algorithm of each USV constituting the swarm to design a marine unmanned floating vessel swarm control system that can be applied to various marine environments. Specifically, to effectively control numerous small USVs for marine research purposes, ocean currents are learned using the LSTM algorithm, and the predicted ocean currents are used to generate a swarm USV control system for USV formations. In this study, a control system model of several small USVs equipped with two rear thrusters and a front lateral thruster was designed. The LSTM algorithm was learned using the previous ocean current data, and the velocity of the following ocean currents was predicted. The predictions were then used as a system disturbance to determine the thrust of the controller. To measure ocean currents in the sea when each USV moves, the velocity, azimuth, and position (latitude, longitude) data from the GPS mounted on the USV were used to measure the velocity and direction of the hull's movement. Further, the flow rate was measured using a flow rate sensor on a small USV. The USV movement and position were controlled using an artificial neural network-PID (ANN-PID) controller. This study entailed a comparative analysis of the designed USV model results and those generated by the simulator, including the behavior control rule of the USV swarm and the path of the actual USV swarm at sea. It was verified that the effectiveness of the USV mathematical model and behavior control rules. By comparing the movement path of the swarm USV with and without the disturbance learning algorithm and ANN-PID control algorithm applied to the designed simulator, the position error and maintenance performance of the swarm formation were analyzed, and the application results were compared.

Bacterial structures formed from the outer membrane and the periplasm components carry biomolecules to expel cellular material and interact with other cells. These outer membrane vesicles (OMVs) can encapsulate bioactive content, which gives OMVs a high potential as alternative drug delivery vehicles or as a platform for novel vaccine development. Single-gene mutants of the hypervesiculating strain Escherichia coli JC8031 were engineered to further enhance OMV production based on metabolic network modelling and in silico gene knockout design (ΔpoxB, ΔsgbE, ΔgmhA, and ΔallD). Mutants were experimentally obtained by genome editing using CRISPR-Cas9 and tested for OMVs recovery observing an enhanced OMV production in all of them. Lipidomic analysis through LC-ESI-QTOF-MS was performed for OMVs obtained from each engineered strain and compared to the wild type E. coli JC8031 strain. The lipid profile of OMVs from the wild type E. coli JC8031 did not change significantly when compared to the mutant strains. The obtained results suggest that the vesicle production can be further improved while the obtained vesicles are not altered in their composition, allowing further study for stability and integrity for use in therapeutic settings.

This research was devoted to study the effect of the tacticity of PMMA on the surface physicochemical properties such as the London dispersive component of the surface energy of the polymer, the polar and dispersive free energies, the Lewis’s acid-base surface parameters, and the Lewis acid and base surface energies of atactic, isotactic and syndiotactic PMMAs as a function of the temperature. Inverse gas chromatography (IGC) at infinite dilution was used to determine the surface thermodynamic properties of PMMA at different tacticities. The experimental values of the net retention time and volume of model organic molecules adsorbed on the atactic, isotactic and syndiotactic PMMAs, were obtained by IGC technique at infinite dilution. The London dispersion interaction energy was used for the separation of the polar and dispersive energy of the different n-alkanes and polar solvents adsorbed on the different PMMA surfaces. The London dispersive surface energy γ_s^d (T) of PMMAs was determined by applying the Hamieh thermal model that took into account the effect of the temperature on the surface area of adsorbed molecules. The obtained results showed non-linear variations of γ_s^d (T) of atactic, isotactic, and syndiotactic PMMAs with three maxima characterizing the three transition temperatures of PMMAs, T_g, T_g and T_(liq-liq) with a shift of these temperatures with the isotactic and syndiotactic PMMAs. It was showed that the polar interaction free energy ∆G_a^p (T) also showed the presence of the three above transition temperatures of the polymers. The study showed an important non-linearity variation of the different acid-base parameters in the various polymer surfaces proving the highest effect of the temperature and the tacticity on these parameters. The determination of the enthalpic and entropic Lewis’s acid-base parameters showed an amphoteric character for the different PMMAs. The basicity of the atactic PMMA was about four times larger than its acidity outside the neighborhood of the transition temperatures of the polymer. Whereas, the isotactic PMMA was about 2 to 2.5 times more basic than acid, while the syndiotactic PMMA exhibited the highest basicity by showing a surface 5 to 8 times more basic than acid. However, the Lewis acid-base parameters strongly depended on the temperature and sudden variations of these surface parameters were observed around the transition temperatures largely depending on the PMMA tacticity. The determination of the polar acid and base surface energies of the three PMMAs led to the same previous transition temperatures with an important effect of the tacticity of PMMA on the values of these acid-base surface energies.

This work communicates analysis of aluminum monoxide, AlO, laser-plasma emission records using line strength data and the ExoMol astrophysical database. A nonlinear fitting program computes comparisons of measured and simulated diatomic molecular spectra. Predicted cyanide spectra of the AlO, ${\rm B}\ ^2\,\Sigma^+ \longrightarrow {\rm X} \ ^2\,\Sigma^+$, $\Delta {\rm v} = 0, \pm 1, \pm 2, + 3$ sequences and progressions compare nicely with 1 nanometer resolution experimental results. The analysis discusses experiment data captured during laser ablation of Al$_2$O$_3$ with 266-nm, 6-mJ pulses. The accuracy of the AlO line strength data is better than one picometer. This work presents as well comparison of the $^{27}$Al$^{16}$O line strength and of ExoMol data for spectral resolutions of 0.1nm and 0.07nm. Accurate AlO databases show a volley of applications in laboratory and astrophysical plasma diagnosis.

The infrared (IR) satellite remote sensing of sea surface skin temperature (SSTskin) is challenging in the northern high latitude region, especially in the Arctic because of its extreme environmental conditions, and thus the accuracy of SSTskin retrievals is questionable. Several Saildrone uncrewed surface vehicles were deployed at the Pacific side of the Arctic in 2019, and two of them, SD-1036 and SD-1037, were equipped with a pair of IR pyrometers on the deck whose measurements have been shown to be useful in the derivation of SSTskin with sufficient accuracy for scientific applications, providing an opportunity to validate satellite SSTskin retrievals. This study aims to assess the accuracy of MODIS-retrieved SSTskin from both Aqua and Terra satellites by comparisons with collocated Saildrone-derived SSTskin data. The mean differences in SSTskin from the SD-1036 and SD-1037 measurements are different by ~0.4 K, largely resulting from differences in the atmospheric conditions experienced by the two Saildrones. The performance of MODIS on Aqua and Terra in retrieving SSTskin is comparable. Negative brightness temperature (BT) differences between 11 μm and 12 μm channels are identified as being physically based, but are removed from the analyses as they present anomalous conditions for which the atmospheric correction algorithm is not suited. Overall, the MODIS SSTskin retrievals show negative mean biases, -0.234 K for Aqua and -0.295 K for Terra. The variations in the retrieval inaccuracies show an association with diurnal warming events in the upper ocean from long periods of sunlight in the Arctic. Also contributing to inaccuracies in the retrieval is the surface emissivity effect in BT differences characterized by the Emissivity-introduced BT difference (EΔBT) index. This study demonstrates the characteristics of MODIS-retrieved SSTskin in the Arctic, at least at the Pacific side, and underscores that more in situ SSTskin data at high latitudes are needed for further error identification and algorithm development of IR SSTskin.

Foot pain related to the plantar fascia is common in adults regardless of athletic background. Many pathologies can lead to the diagnosis of plantar enthesopathy, but the most relevant to this case study is related to structural defects within the plantar fascia. Due to the variety and sometimes unclear etiology of plantar fasciosis, no single standard of care treatment protocol is recognized. Often, patients receive NSAIDs, night splints, taping, physical therapy, foot orthosis, and extracorporeal shock wave therapies. This study presents Wharton Jelly (WJ) tissue allografts as an additional intervention for patients who fail standard-care treatments. WJ allografts are applied to supplement connective tissue defects directly, unlike other therapies, which aim to reduce swelling and symptomatic pain. This retrospective study includes seven patients who have previously failed standard-of-care treatment. Each received extracorporeal pulse-activated therapy (EPAT), WJ, laser therapy, and an orthotic. Patient progress was tracked using a visual analog scale, 0-10 scoring, reported by the patient at the initial visit and approximately thirteen weeks following, reporting an average improvement of 50%. The study's limitations include a small cohort size and a non-blinded retrospective design. These promising results provide evidence for a more extensive, randomized study to define dosage protocols further and confirm safety and efficacy.

Atlas Posterior Arch Deficiency (APAD) is a rare anatomical variation of the atlas vertebra that can be detected using cone-beam computed tomography (CBCT). This study aims to evaluate the prevalence, classification, and clinical implications of APAD in an Italian cohort.

Titanium alloys belong to the metal biomaterials that are one of the most widely used in medicine. In recent years, in order to reduce the use of vanadium, Ti6Al4V alloy is increasingly replaced by Ti6Al7Nb alloy. In addition, to ensure the best possible biocompatibility, its surface is subjected to appropriate modifications, for example, anodic oxidation. Despite the extensive use of anodic oxidation of titanium implants in orthopedics, there are few works focused on a detailed analysis of the chemical composition of the surface layers. In addition, the effect of treatments before anodic oxidation on the properties of the produced layer has not been analyzed. Thus, the purpose of this study was to analyze in detail the chemical composition of the passive layer of Ti6Al7Nb alloy obtained by anodic oxidation preceded by sandblasting. Moreover, the physicochemical properties of the analyzed surface affecting biocompatibility were determined. For this purpose, surface observation, wettability and roughness tests, microhardness tests, electrochemical tests and phase composition analysis were carried out. In addition, the preclinical suitability, of the surface modified in this way, was evaluated by cytotoxicity tests.

In this article, we describe a simple procedure for evaluating the sterility of nutrient media using a shear-horizontal surface acoustic wave (SH-SAW) biosensor. We used the SH-SAW biosensor platform to monitor the time-dependent phase responses of the material for the media that binds to a monolayer of 3-mercaptopropanyl-N-hydroxy succinimide on the biosensor surface. Increases in the phase shift less than 50% of the starting phase shift recorded 180 minutes after the sterilization indicate a successful sterility test of the media. Our devices were then applied to sterility testing using a viable Escherichia coli (E. coli) K-12 solution to confirm our hypothesis. Filtered LB Broth was the negative control, and a 24-hour culture of E. coli was the positive control. Before testing, the cell solution was pelleted, the media decanted, and then replaced with a 1x phosphate-buffered saline solution (1x PBS). Since we know that the N-hydroxysuccinimide residues will bind to amine groups, only in cases where microbial species are present will the surface binding increase greater than 50%. We confirmed our hypothesis using SH-SAW biosensors and overnight E. coli cultures. The sensitivity for our 250 MHz quartz SH-SAW sensors was calculated based on the response from the E. coli K-12 solution over the linear dynamic range, which appears to be 2x10^4 – 2x10^7 CFU per ml and has a sensitivity of S = 1.655x10^5 o m2 Kg-1. The limit of detection (LOD) for these sensors was calculated to be approximately 2x10^-9 grams (g), which is estimated to be approximately 2,000 Escherichia coli (E. coli) K-12 cells. However, the sensitivity and insertion loss remained approximately unchanged before and after coating the sensor with 3,3'-Dithiobis(succinimidyl) Propionate (DSP).

We measured the anelastic, dielectric and structural properties of the metal-free molecular perovskite (ABX$_{3}$) (MDABCO)(NH$_{4}$)I$_{3}$, which has already been demonstrated to become ferroelectric below $T_{\text{C}}=$ 448~K. Both the dielectric permittivity measured in air on discs pressed from powder and the complex Young's modulus measured on resonating bars in vacuum show that the material starts deteriorating with loss of mass just above $T_{\text{C}}$, introducing defects and markedly lowering $T_{\text{C}}$. The elastic modulus softens of 50\% when heating through the initial $T_{\mathrm{C}}$, contrary to usual ferroelectrics, which are stiffer in the paraelectric phase. This suggests improper ferroelectricity, where the primary order parameter of the transition is not the electric polarization, but the orientational order of the MDABCO molecules. The degraded material presents thermally activated relaxation peaks in the elastic energy loss, whose intensities increase together with the decrease of ~$T_{\mathrm{C}}$. The peaks are much broader than pure Debye, due to the general loss of crystallinity, also apparent from X-ray diffraction, but their relaxation times have parameters typical of point defects. It is argued that the major defects should be of the Schottky type, mainly due to the loss of (MDABCO)$^{2+} $ and I$^{-}$, leaving charge neutrality, and possibly also (NH$_{4}$)$^{+}$ vacancies. The focus is on an anelastic relaxation process peaked around 200~K at $\sim 1$~kHz, whose relaxation time follows the Arrhenius law with $\tau $$_{0}$~$\sim $\ $10^{-13}$\ s and $E\simeq 0.4$~eV. This peak is attributed to I vacancies (V$_{\text{X}}$) hopping around MDABCO vacancies (V$_{\text{A}}$) and its intensity presents a peculiar dependence on temperature and content of defects. The phenomenology is thoroughly discussed in terms of lattice disorder introduced by defects and of partition of V$_{\text{X}}$ among sites that are far from and close to the cation vacancies. A method is proposed for calculating the relative concentrations of V$_{\text{X}}$, that are untrapped, paired with V$_{\text{A}}$ or forming V$_{\text{X}}$--V$_{\text{A}}$--V$_{\text{X}}$ complexes.

In this research, we investigate the bending of photon light and/or time-like geodesics within the context of four-dimensional space-time geometry, specifically in the presence of topological defects. These topological defects manifest as cosmic string space-time configurations, encompassing screw dislocation, spiral dislocation, and spacelike dislocation. Our primary objective is to determine the extent of deflection experienced by light-like and time-like geodesics and analyze how this deflection is affected by the cosmic string parameter, screw dislocation parameter, and spacelike dislocation parameter. To accomplish this, we employ a derivation technique that centers on the observation that photon rays (light-like geodesics) and/or time-like geodesics follow paths parallel to the z-axis while maintaining a constant radius along the cylinder.

Advancements in genomics, bioinformatics and genome editing have uncovered new dimensions in gene regulation. Post-transcriptional modifications by the alternative splicing of mRNA transcripts are critical regulatory mechanisms of mammalian gene expression. In the heart, there is an expanding interest in elucidating the role of alternative splicing in transcriptome regulation. Substantial efforts have been directed towards investigating this process in heart development and failure. However, few studies have shed light on alternative splicing products and their dysregulation in congenital heart defects (CHDs). While elegant reports have shown the crucial roles of RNA binding proteins (RBPs) in orchestrating splicing transitions during heart development and failure, the impact of RBPs dysregulation or genetic variation on CHDs has not been fully addressed. Herein, we review the current understanding of alternative splicing and RBPs’ roles in heart development and CHDs and discuss the impacts of perinatal splicing transition and its dysregulation in CHDs. We further summarize discoveries made of causal splicing variants in key transcription factors that have been implicated in CHDs. Improved understanding of the roles of alternative splicing in heart development and CHDs may potentially inform novel preventive and therapeutic advancements for newborn infants with CHDs.

Urban trees are often more sun- and wind-exposed than their forest-grown counterparts. These environmental differences can impact how many species grow – impacting trunk taper, crown spread, branch architecture, and other aspects of tree form. Given these differences, windthrow models derived from traditional forest production data sources may not be appropriate for urban forest management. Additionally, visual abnormalities historically labeled as “defects” in timber production may not have a significant impact on tree failure potential. In this study, we look at urban tree failures associated with Hurricane Irma in Tampa, Florida, USA. We used spatial analysis to determine if patterns of failure existed among our inventoried trees. We also looked at risk assessment data to determine which visual defects were the most common and the most likely to be associated with branch or whole-tree failure. Results indicate that there was no spatial pattern associated with the observed tree failures – trees failed or withstood the storm as individuals. While some defects like decay and dead wood were associated with increased tree failure, other defects like weak branch unions and poor branch architecture were less problematic.

The evaluation of geometric defects is necessary in order to maintain the integrity of structures over time. These assessments are designed to detect damages of structures and ideally help inspectors to estimate the remaining life of structures. Current methodologies for monitoring structural systems, while providing useful information about the current state of a structure, are limited in the monitoring of defects over time and in linking them to predictive simulation. This paper presents a new approach to the predictive modeling of geometric defects. A combination of segmented from point clouds are parametrized using the convex hull algorithm to extract features from detected defects, and a stochastic dynamic model is then adapted to these features to model the evolution of the hull over time. Describing a defect in terms of its parameterized hull enables consistent temporal tracking for predictive purposes, while implicitly reducing data dimensionality and complexity as well. In this study, 2D point clouds analogous to information derived from point clouds were first generated over simulated life-cycles. The evolutions of point cloud hull parameterizations were modeled as stochastic dynamical processes via autoregressive integrated moving average (ARIMA) and vectorized autoregression (VAR) and compared against ground truth. The results indicate that this convex hull approach provides consistent and accurate representations of defect evolution across a range of defect topologies and is reasonably robust to noisy measurements, however assumptions regarding the underlying dynamical process play a significant the role in predictive accuracy. The results were then validated on experimental data from fatigue testing with high accuracy. Longer term, the results of this work will support finite element model updating for predictive analysis of structural capacity.

The present study investigates the impact of electrode surface roughness on the electrofreezing of water. This research focuses on how the electrode roughness induced by a laser treatment affects the nucleation and growth of ice crystals under controlled electric fields. To achieve this, a series of experiments were conducted using deionized water samples placed between electrodes with varying surface roughness. The electrodes, fabricated with the Al6061 T6 alloy were structured via the Laser Shock Processing (LSP) method. For this purpose, the pulsed densities during the LSP process were varied from 900 to 2500 pulses/cm2. The increase of the pulse density was correlated to the surface structuring and to the microstructural features and average roughness of the LSP-treated Al6061 alloy. A wavy-like microstructure was induced upon the LSP treatment with average roughnesses between ~ 3.5 and 6 µm at the selected pulse densities. The results indicate that electrode roughness significantly influences the electrofreezing process. Rougher electrodes were found to lower the nucleation temperature compared to smoother ones, suggesting enhanced ice nucleation activity. The findings are attributed to the increased electric field concentration at the asperities of the rough surfaces, which may facilitate the alignment of water molecules and the formation of critical ice nuclei.

Introduction: The repertoire of microRNAs (miRNAs) in thyroid carcinomas starts to be elucidated. Among differentiated thyroid carcinomas (DTC), papillary thyroid carcinoma (PTC) is the most common. The assessment of miRNAs expression may contribute to refine the pre-surgical diagnosis, in order to obtain a personalized and more effective treatment of patients. Aims: This study aims to evaluated 1) miRNAs expression in a series of DTC, and the association with the presence of selected genetic mutations, in order to improve diagnosis and predict biologic behavior of DTC/PTC. 2) the reliability of molecular tests in Ultrasound-guided Fine Needle Aspiration Cytology (US-FNAC) for a more precise preoperative diagnosis. Material and methods: This series includes 176 samples (98 cytology samples and 78 formalin-fixed paraffin embedded (FFPE) tissues) obtained from 106 patients submitted to surgery, being 13 benign lesions (controls) and 93 DTCs (cases). The microRNA expression was assessed for miR-146b, miR-221, miR-222, and miR-15a by quantitative reverse transcriptase-polymerase chain reaction (qRT-PCR) and the results were analyzed using the 2- ΔΔCT method, using miR16 as an endogenous control. The discriminative ability of miRNAs expression regarding PTC diagnosis was evaluated using the area under the Receiver Operating Characteristic Curve (AUC). The association of miRNAs expression, clinicopatological features and genetic alterations (BRAF, RAS and TERTp) was evaluated in PTCs. Results/Discussion: All the analyzed miRNAs showed a tendency to be over expressed in DTCs/PTCs when compared with benign lesions, both in cytology and histology samples. In cytology, miRNAs expression levels were higher in malignant than in benign tumors. In histology, corresponding discriminative abilities regarding PTC diagnosis were: miR-146b (AUC0.94, 95%CI 0.87-1), miR-221 (AUC0.79, 95%CI 0.68-0.9), miR-222 (AUC0.76, 95%CI 0.63-0.89) and miR-15a (AUC0.85, 95%CI 0.74-0.97). miR-146b showed 89% sensitivity (se) and 87% specificity (sp); mi-R221 se=68.4, sp=90; miR222 se=73, sp=70, and mi-R15a se=72, sp=80. MicroRNAs were associated with aggressive clinicopathological features and tumor progression in PTCs (p &lt; 0.05), particularly for miR-222. Our data reveals a significant association between higher expression levels of miR-146b, miR-221 and miR-222, with the presence of BRAF mutation (p&lt;0.001), and miR-146b (p=0.016) and miR-221 (p=0.010) with the presence of RAS mutation, suggesting an interplay of these mutations with miRNAs expression. Although this study has a relatively small sample size, over expression of miRNAs in cytology may contribute to a more precise preoperative diagnosis. The miRNAs showed a good discriminative ability in PTC diagnosis. The association between the miRNAs expression profile and genetic alterations results could be useful for an accurate diagnosis of DTCs/PTCs in FNAC.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

Following technological advances, autonomous and remote-controlled ships are performing trials in some sea areas; a mandatory goal-based MASS code, expected to enter into force on 1 January 2032, is under discussion in the International Maritime Organization (IMO). However, there are no unified standards regarding verification methods to define operating limitations for cutting-edge technologies, which are expected to be elements of MASS, so it is difficult to assess the risk factors for the management and operation of MASS. This paper outlines the regulatory framework for MASS, followed by a discussion of its application, considering the differences between MASS and automated driving, and how to develop safety management and operation using standards for automated driving. A requirements management framework developed as a system and software engineering standards to build safety management and operation of MASS is proposed. It is also suggested that the requirements management framework could be used not only for MASS development but also for regulatory review from a requirements management view.

Agriculture stands as the cornerstone of Africa’s economy, supporting over 60% of the continent’s labor force. Despite its significance, the quality assessment of agricultural products remains a challenging task, particularly at large scale, consuming valuable time and resources. The African plum is an agricultural fruit that is widely consumed across West and Central Africa but remains underrepresented in AI research. In this paper, we collected a dataset of 2,892 African plum samples from fields in Cameroon representing the first dataset of its kind for training AI models. The dataset contains images of plums annotated with quality grades. We then trained and evaluated various state-of-the-art object detection and image classification models, including YOLOv5, YOLOv8, YOLOv9, Fast R-CNN, Mask R-CNN, VGG16, Detectron-121, MobileNet and ResNet, on this African plum dataset. Our experimentation resulted in mean average precision scores ranging from 88.2% to 89.9% and accuracies between 86% and 91% for the object detection models and the classification models respectively. We then performed model pruning to reduce model sizes while preserving performance, achieving up to 93.6% mean average precision and 99.09% accuracy after pruning YOLOv5, YOLOv8 and ResNet by 10-30%. We deployed the high-performing YOLOv8 system in a web application, offering an accessible AI-based quality assessment tool tailored for African plums. To the best of our knowledge, this represents the first such solution for assessing this underrepresented fruit, empowering farmers with efficient tools. Our approach integrates agriculture and AI to fill a key gap.

In this paper, we explore the hypothesis that topological defects formed in the quark-gluon plasma (QGP) of the early universe, specifically flux tubes and domain walls, could serve as stable dark matter candidates. Theoretical analysis of the QCD vacuum structure reveals that these defects can form due to nontrivial topological configurations, with the Lagrangian density incorporating topological terms. We model the formation and stability of flux tubes and domain walls, estimating their energy densities and dynamics within the QGP. Flux tubes, with energy per unit length approximately given by $\mu \approx \frac{\sigma}{g_s^2}$, and domain walls, characterized by a surface energy density $\sigma_{\text{DW}} \sim \Lambda_{\text{QCD}}^3$, exhibit unique gravitational signatures. These signatures include distinct gravitational lensing patterns due to their linear and planar mass distributions, making them detectable through astrophysical surveys. Furthermore, their minimal interaction with conventional matter aligns well with observational constraints on dark matter properties. We discuss potential experimental approaches for detecting these defects, including high-energy collider experiments and detailed analysis of gravitational lensing data. Our findings suggest that topological defects in the QGP provide a compelling and novel solution to the dark matter problem, offering a new direction for both theoretical investigation and experimental verification.

LSM4 is an essential yeast gene encoding a component of different LSM complexes involved in the regulation of mRNA splicing, stability and translation. In previous papers we reported that the expression in S. cerevisiae of the K. lactis Lsm4 gene lacking the C-terminal Q/N-rich domain in a Lsm4 null strain S. cerevisiae (Sclsm4D1) restored cell viability. Nevertheless, in this transformed strain we observed some phenotypes which are typical markers of regulated cell death, Reactive Oxygen Species and oxidated RNA accumulation. In this paper we report that a similar truncation operated in the S. cerevisiae LSM4 gene confers to cells the same phenotypes observed with the K.lactis LSM4D1 gene. Up to now there was no evidence on the direct involvement of LSM4 in autophagy. Here we found that the Sclsm4D1 mutant showed defects in the induction of autophagy and it was very sensitive to nitrogen starvation or treatment with low doses of rapamycin, an inducer of autophagy. Moreover, both during nitrogen starvation and ageing, the Sclsm4D1 mutant accumulated cytoplasmic autophagy-related structures, suggesting a role of Lsm4 in Phagophore Assembly Site (PAS) processing and/or vacuolar autophagosome internalization

Clients are increasingly looking for fast and effective means to quickly and frequently survey and communicate the condition of their buildings so that essential repairs and maintenance work can be done in a proactive and timely manner before it becomes too dangerous and expensive. Traditional methods for this type of work commonly comprise of engaging building surveyors to undertake a condition assessment which involves a lengthy site inspection to produce a systematic recording of the physical condition of the building elements, including cost estimates of immediate and projected long-term costs of renewal, repair and maintenance of the building. Current asset condition assessment procedures are extensively time consuming, laborious, and expensive and pose health and safety threats to surveyors, particularly at height and roof levels which are difficult to access. We propose a method for automated detection and localisation of key building defects from images using deep learning and convolution neural networks. The proposed model is based on a pre-trained VGG-16 classifier with Class Activation Mapping (CAM) for object localisation. The model has proven to be robust and able to accurately detect and localise mould growth, stains, and paint deterioration defects arising from dampness in buildings. The approach is being developed with potentials to scale-up to support automated detection of defects and deterioration of buildings in real-time using mobile devices and drones.