In the drive towards environmental restoration and sustainable energy solutions, effective utilization and management of agricultural crop residues are vital to mitigate greenhouse gas (GHG) emissions and waste accumulation. Converting biogenic wastes into biofuels and bioproducts has the potential to tackle the energy crisis and contribute to environmental remediation. In this investigation, teff husk, primarily generated in Ethiopia during teff production within the agro-industrial sector, is used as the feedstock for the slow pyrolysis process. In Ethiopia, it is estimated that over 1.75 million tons of teff husk are generated annually, with a significant portion being incinerated in the fields, resulting in substantial environmental pollution. This study focuses on assessing teff husk as a potential material for slow pyrolysis, a crucial stage in biochar production, to tap into its biochar-producing potential. To determine the composition of the biomass, the teff-husk was initially analyzed by thermogravimetry. The significant presence of fixed carbon indicates that teff husk is a viable candidate for pyrolytic conversion into biochar particles. The process of slow pyrolysis took place at three varied temperatures—specifically, at 400, 450, and 500 °C. Process parameters of slow pyrolysis such as reaction time, temperature, and heating rate were enhanced to obtain maximum biochar yields. The highest biochar yield of 43.4 wt% was recorded at optimized reaction time, temperature, and heating rate of 120 min, 400 °C, and 4.2 °C/min, respectively. Furthermore, biochar's physicochemical, SEM-EDX, FTIR, and TGA characterization were performed. The thermal stability and carbon content of biochar were found to rise at higher temperatures. Unlike fuel recovery, the results suggest that teff-husk can be used as a feedstock for biochar production.

Modified aluminum slag (MAS) was applied as an adsorbent for Congo red (CR) prepared by the hydrothermal treatment of Ca (OH) 2. At 25 ℃, with a MAS dosage of 0.3g, initial CR concentration of 100 mg/L and initial pH=5, and the adsorption time was 40 min, the CR removal efficiency was 98.41%. The adsorption trend of CR conformed to the second-order kinetics, and the adsorption isotherm follows the Freundlich isotherm model. Compared with RAS, MAS has a larger pore volume and specific surface area. The mechanism of action of MAS on CR was the interaction between membrane diffusion and internal diffusion, and the adsorption rate during the membrane diffusion was the fastest.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

A method for accurately determining the chemical composition of deposits at the bottom of pores during the electrocoloring (e-coloring) of aluminum anodic oxide (AAO) layers in tin-based solutions is developed. The aluminum samples were AC e-colored after DC sulfuric anodization. Free-standing, tin e-colored aluminum oxide film was obtained by selective dissolution of the metallic aluminum from the AAO in copper chloride solution to access the deposit directly at the bottom of the pore. This allowed us to take XPS analysis directly from the deposits at pore bottoms without any interference from the base material or insulating barrier layer. The results revealed the presence of a mixture of tin oxide and metal in the deposits, which were richer in oxide content. Furthermore, a cyclic voltammetry experiment mimicking real polarization conditions during AC conditions was optimized and used to gain a deeper understanding of the electrochemical reactions that occur during AC electrocoloring. The comparison of CV results in tin-free and tin-containing electrolytes indicated that the tin deposited during a cathodic cycle is oxidized in the anodic cycle. The formation of tin based deposits radically changed the CV behavior. The XPS and cyclic voltammetry results consistently show that the deposits formed during e-coloring comprised a mixture of metallic and oxidic tin species richer in oxide content.

Red mud (RM) is composed of a waste alkaline solution (pH = 13.3) obtained from the production of alumina. It contains high concentrations of soluble hematite (Fe2O3), goetite (FeOOH), gibisite [Al(OH)3], a boemite (AlOOH), anatase (Tetragonal - TiO2), rutile (Ditetragonal dipyramidal - TiO2), hydrogarnets [Ca3Al2(SiO4)3−x(OH)4x], and perovskite (CaTiO3). It was shown to be an excellent catalytic mixture for biodiesel production. To demonstrate the value of RM, an environmentally friendly process of transesterification in aqueous medium using waste cooking oil (WCO), MeOH and waste alkaline solution (WAS) obtained from aluminum production was proposed. Triglycerides of WCO reacted with MeOH at 60 oC to yield mixtures of fatty acid methyl esters (FAMEs) in the presence of 0.019% (w/w) WAS/WCO using the WAS (0.204 mol L-1, predetermined by potentiometric titration) from aluminum production by the Bayer process. The use of the new catalyst (WAS) resulted in a high yield of the products (greater than 99% yield).

Red mud (RM) is a residue obtained from the production of alumina. It contains a high concentration of metal oxides and waste concentrated sodium hydroxide solution (pH = 13). To increase the value of RM, an environmentally friendly process of transesterification using waste cooking oil (WCO), MeOH and concentrated sodium hydroxide solution (CSHS) from aluminum production was proposed. Triglycerides of WCO reacted with MeOH at 60 oC to yield mixtures of fatty acid methyl esters (FAMEs) in the presence of 2.03% (w/w) CSHS/WCO using the CSHS (0.204 mol L-1, predetermined by potentiometric titration) from aluminum production by the Bayer process or with the addition of 0.68% (w/w) fabric softener (3% w/w cetyltrimethylammonium chloride in solution) as a phase transfer (PTA) agent. The addition of PTA to the catalyst resulted in a better yield of the products (greater than 98% yield). A simplified mechanism is presented to account for the experimental results.

Improper disposal of waste plastic has caused serious ecological and environmental pollution problems. Transforming plastics into high value-added chemicals can not only achieve efficient recycling of waste plastics, but also an effective way to control white pollution. The catalyst selectively breaks the C-C bond of polyolefin plastic under heat treatment and converts it into liquid fuel, thus realizing sustainable recycling of plastics and has a good development prospect. This review provides a detailed overview of the current development of catalytic pyrolysis, catalytic hydrolysis, solvent decomposition and supercritical hydrothermal liquefaction for cracking plastics to make fuel oil. The reaction mechanism, influencing factors and promoting effects of catalysts in various degradation technologies are analyzed and summarized and the latest proposed tandem reaction for degrading plastics is briefly introduced. Finally, some optimization paths of waste plastic pyrolysis to fuel oil technology are proposed: synergies between mixed raw materials, in-depth exploration of catalysts, design and manufacture of reactors that match the pyrolysis technology. All these are important research directions for promoting the industrialization of plastic pyrolysis to fuel oil.

The aim of this study was utilization of ground tea waste (GT) left after brewing the black tea as a biofiller of natural rubber (NR) composites. Ionic liquids (ILs), i.e., 1-ethyl-3-methylimidazolium lactate and 1-benzyl-3-methylimidazolium chloride, often used to extract phytochemicals from tea, were applied to improve the dispersibility of GT particles in elastomeric matrix. The influence of GT loading and ILs on curing characteristics, crosslink density, mechanical properties, thermal stability and resistance of NR composites to thermo-oxidative aging was investigated. The amount of GT did not significantly affect curing characteristics and crosslink density of NR composites, but had serious impact on tensile properties. Applying 10 phr of GT improved the tensile strength by 40% compared to unfilled NR. Further increasing in GT content worsened the tensile strength due to the agglomeration of biofiller in elastomer matrix. ILs significantly improved the dispersion of GT particles in elastomer and increased the crosslink density by 20% compared to the benchmark. Owing to the poor thermal stability of pure GT, it reduced the thermal stability of vulcanizates compared to unfilled NR. Most importantly, GT-filled vulcanizates showed improved resistance to thermo-oxidative aging, since the aging factor increased by 25% compared to the unfilled vulcanizate.

Silica fly ash, Certyd aggregate, and an alkaline solution were used to produce lightweight geo-polymer concretes. The compressive strength, water absorption, bulk density and SEM photos showing the structure of the obtained composite were carried out. Tests conducted on the specifi-cation of lightweight geopolymer concretes have revealed significant chemical interactions between the ash aggregate and the geopolymer mortar, particularly when the coarse aggregate surface has been pre-treated with an alkaline solution. Statistical analysis of the experimental data, which in-vestigated the influence of three key variables on compressive strength, water absorption, and bulk density of Lightweight Geopolymer Concrete (LBG), identified the following factors as having the most substantial impact: the quantity of alkali used, the curing temperature, and the concentration of alkali in the mixture. The optimal test series exhibited a commendable compressive strength of 20.14 megapascals (MPa), accompanied by a water absorption rate of 14.72% and a bulk density of 1486.6 kilograms per cubic meter (kg/m³). These findings underscore the importance of alkali con-tent, curing temperature, and alkali concentration in tailoring the properties of lightweight geo-polymer concrete to meet specific performance requirements.

In an attempt to reuse fibrous textile waste and, at the same time, to address dye pollution in textile wastewater, waste cotton-based yarn was utilized as both a cheap and sustainable adsorbent and a precursor for carbon adsorbent production. Cotton and cotton/polyester yarn samples underwent thermal modification through carbonization followed by chemical activation with KOH. Various techniques including nitrogen adsorption-desorption isotherms, scanning electron microscopy, Fourier transform infrared spectroscopy, and surface charge determination were employed to analyze the morphological and surface properties of the cotton-based adsorbents. Adsorption properties were evaluated by testing the removal of selected cationic and anionic dyes from water. The impact of temperature, contact time, initial concentration, and pH of the adsorbate solution on adsorption was investigated, with experimental data analyzed using theoretical models. While carbonization alone did not significantly enhance adsorption properties, activated samples exhibited high efficacy in removing both cationic and anionic dyes from water. Despite the negative influence of the polyester component in the carbon precursor on the efficiency of activated samples in removing methyl orange, results indicated that activated cotton and cotton/polyester yarn could be used to prepare highly efficient adsorbents for the rapid removal of methylene blue from real wastewater samples.

Households and businesses are generating unprecedented levels of electrical and electronic wastes (e-waste), fueled by modernisation and rapid obsolescence. While the challenges imposed by e-waste are similar everywhere in the world, disparities in progress to deal with it exists; with developing nations such as South Africa lagging. The increase in e-waste generation increases the need to formulate strategies to manage it. This paper presents an overview of e-waste management on a global and South African scenarios with a specific case for Cathode Ray Tube (CRT) waste management practices in South Africa. CRTs present the biggest problem for recyclers and policy makers because they contain hazardous elements such as lead and antimony. Common disposal practices have been either landfilling or incineration. The research into the South African practices with regards to CRT waste management showed that there is still more to be done to effectively manage this waste stream. This is despite clear waste regulatory frameworks in the country. However, recent developments have placed e-waste as a priority waste stream, which should lead to intensified efforts in dealing with it. Overall, these efforts should aim to maximise diversion from landfilling and to create value-addition opportunities, leading to social and environmental benefits.

This study investigated the relationship between aluminum adjuvant vaccines and the prevalence of 4 childhood diseases (Autism, Allergies, Asthma, ADD/ADHD) using data from the 2020-2021 National Survey of Children's Health (NSCH) [1] and the Centers for Disease Control National Immunization Survey (CDC NIS) [2]. The study found an association with aluminum adjuvant dosage and the prevalence of each disease studied (Autism, Allergies, Asthma, ADD/ADHD) through a weighted regression analysis of disease prevalence against the summed likelihood of aluminum adjuvant vaccine uptake.

Solvent free copolymerization of epoxides derived from fatty acid esters of waste cooking oil with phthalic anhydride using (salen)CrIII Cl as catalyst and n-Bu4NCl/DMAP as co-catalyst was carried out for the first time under microwave irradiation, where reaction time was reduced from number of hours to minutes. The polyesters were obtained with molecular weight (Mw = 3084-6740 g/mol) and dispersity values (D = 1.18-1.92), when (salen)CrIII Cl/n-Bu4NCl was used as catalysts. While in case of DMAP as a co-catalyst, polyesters with improved molecular weight (Mw = 5537-6925 g/mol) and narrow dispersity values (D = 1.07-1.28) were obtained even at reduced concentrations of (salen)CrIII Cl and DMAP. The obtained products were characterized and evaluated by attenuated total reflection-fourier transform infrared spectroscopy (ATR-FTIR), proton nuclear magnetic resonance (1H-NMR) spectroscopy, gel permeation chromatography (GPC) and thermogravimetric analysis (TGA) Techniques.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

Waste glycerol can be subjected to various processing operations, including purification and re-fining, to obtain glycerol of appropriate purity. In addition, alternative methods of utilising waste glycerol are also being sought, e.g. by converting it into other valuable chemical products or biofuels. Therefore, various technologies are being developed to utilise this type of waste effectively and sustainably. The production of value-added products from waste glycerol is an important issue that determines the improvement of the economic viability of biofuel production and corresponds to the model of a waste-free and emission-free circular economy. This paper characterised the mechanisms and evaluated the efficiency of existing methods of microbiological utilisation of waste glycerol into liquid biofuels, including biodiesel, bioethanol and biobutanol, and identified further directions for the production of value-added products. In addition, a bibliographical analysis of publications re-lated to the production of liquid fuels and economically valuable products from glycerol was carried out, the progress of research and application work was assessed and directions for future research were identified.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

Recycling information can be complex and often confusing which may subsequently reduce the participations in any waste recycling schemes. As a result, this research explored the roles as well as the importance of a holistic approach in designing recycling information using 15 expert-based in-depth interviews. The rationale was to offer a better understanding of what constitutes waste, recycling, and how recycling information should be designed and presented to make recycling more attractive/convenient. Based on the research participants’ perceptions with supports from the existing studies, this research sub-categorised recycling information into three different themes, termed the “WWW” of recycling information components. As a result, these components (or attributes) were extensively described (using findings of semi-structured interviews) to elicit pragmatic guidance for practitioners, policy-makers, and other stakeholders in designing structured communication or information strategies that may simplify and subsequently increase waste-recycling practices. The policy implications of holistic information in enhancing recycling are further discussed.

The global increase in population has placed significant pressure on food security, leading to the emergence of aquaculture as a vital source of aquatic foods. However, rising costs and the limited availability of fishmeal in aquafeeds have spurred the search for alternative protein sources. While plant-based ingredients have been integrated into commercial aquafeeds, they come with challenges, including low protein content, palatability issues, and the presence of antinutritional factors. In this context, fish silage, derived from fish waste and discarded fish, stands out as a promising alternative technology due to its cost-effectiveness and sustainability attributes. The production of fish silage involves the addition of organic/inorganic acids or lactic acid bacteria to homogenized fish waste. This process yields a valuable mixture rich in peptides, free amino acids, and partially hydrolyzed proteins, offering significant nutritional benefits for animal diets. Beyond its nutritional advantages, fish silage contributes to environmental sustainability by reducing the impact of waste disposal and enhancing the value of fish waste. The objective of this review is to promote sustainable practices in the aquaculture industry in response to the increasing demand for high-quality feed nutrients. To achieve this, it includes an analysis of research results related to silage technology, an appraisal of the advantages and disadvantages of using fish silage as a feed additive, and a focus on emerging trends in this field.

The valorization of the large amount of crude glycerol formed from biodiesel industry, is of primordial necessity. One possible direction with high interest to the biorefiniery sector is the production of fuel additives as solketal, though the acetalization of glycerol with acetone. This is a chemical process that conciliates high sustainability and economic interest, since solketal contributes to the fullfilment of a Circular Economy Model through its use in biodiesel blends. The key to guarantee high efficiency and high sustainability for solketal production is the use of a recovery and recyclable heterogeneous catalyst. Some examples are already reported in the literature (first example in 2012), and this review intends to conciliate the information spreaded in this topic and established the most important reacional parameters and the main catalytic characteristics strategies to achieve high solketal production in short reaction time.

Solid waste management in Accra is a major challenge to the Metropolitan Authorities and inhabitants. The rapidly increasing population coupled with poor capacity of the municipal and private waste management companies to management waste effectively has created issues of environmental concern. Due to poor waste managements systems, most household dispose waste indiscriminately leading to floods and health issues. The study showed that about 60% of household waste is organic materials which has the potential to be converted to compost for agriculture purpose. Meanwhile plastics and rubbers which litters the environment as well as blocking major storm drains and gutters hence creating huge environmental hazard is made of 11% of the total component of most household waste generated daily. The study also revealed that among the methods of disposing waste, dumping waste in skip containers located at authorized places was the preferred means of disposing waste by household though others also dispose waste by other means such as burying and burning. Inadequate skip containers per population of household in an area coupled with irregularity of tracks picking these containers makes skip containers dumping site ugly scene, hence creating health issues. Among the constraints that impact negatively on sustainable waste management in Accra Metropolis, economic constraints was perceived as the main challenge which affect efficient waste management. Currently the country is going through serious economic challenges so government does not release money timely to fund projects which waste management is key. Most donor partners that use to support the government with funds have either reduced or redrawn their services as they have no confidence in the state of Ghana economy. Aside the constrains, the study also indicated that factors such as poor public attitude towards waste management, poor enforcement of sanitation by-laws, inadequate and untimely release of government funds were also seen as the main factors affecting waste management.

In the discussion on environmental policies, the notion of eco-efficiency is often used. Eco-efficiency is defined as the delivery of products and services with competitive values, while reducing the ecological impacts and satisfying human needs. In an environment of great competitiveness in which the companies operate, the improvements in the productive process is one of the differentiating factors for guaranteeing a strong competition. Also it is essential rationalizing energy consumption and natural resources. For this it is necessary to understand the main operations and dynamics of the company. This work presents an empirical study of a Portuguese company in the industrial sector. The problematic here presented is based on the company’s growing concern to reduce the amount of scrap produced. From the literature research that was performed, a strong dependence relation between the different variables in the extrusion process was found. The main objective of this work is to model the aluminium extrusion process, with the aim of minimizing the production of scrap. For this several variables involved in the process are taking into account. Using statistical techniques, in particular multiple linear regressions, it was possible to identify the importance of the variables under study for the scrap production.

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

This paper presents the results of investigations into the pyrolysis of waste polypropylene in a laboratory fixed-bed batch reactor. The experiments were designed and verified in such a way as to allow the application of the Response Surface Methodology (RSM) in the development of an empirical mathematical model that quantifies the impacts mentioned above. The influence of the mass of the raw material (50, 100 and 150 g), together with the reactor temperature (450, 475 and 500 °C) and the reaction time (45, 50 and 75 min) was examined. It has been shown that the mass of the raw material, i.e. the filling volume of the reactor, has a significant influence on the pyrolysis oil yield. This influence exceeds the influence of reactor temperature and reaction time. This was explained by observing the temperature change inside the reactor at three different spots at the bottom, middle and top of the reactor. Recorded temperature diagrams show that with greater masses of feedstock, local overheating occurs in the middle part of the reactor, which leads to overcracking of vapor products, and from there to an increased formation of non-condensable gases, i.e. reduced yield of pyrolytic oil.

Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

Plasmonic sensors have great potential for widespread usage, but the prohibitive cost of noble metals restrains the wider adoption of this technology. The aim of our study is to develop a cost-effective Al-based alternative to plasmonic detectors commonly based on noble metals. We considered a structure that consists of a Si p-n junction with an overlying grating-relief aluminum layer. The investigation of the infrared plasmonic resonance dependency on the structure geometric parameters and optimization of the fabrication process allowed us to determine optimal parameters for photodetection enhancement. The resonance photoresponse of optimized aluminum-based plasmon-polariton photodetector was significantly improved and became comparable to noble metal-based analogs. Our results can be used for the creation of cost-effective high-sensitivity plasmonic sensors.

Colombia is the world's leading producer of mild washed arabica coffee and produces 12.6 million bags of green coffee, but at the same time 784,000 tons of waste biomass are dumped in open fields, of which only 5% is recovered or used. The objective of this project was to evaluate the production of platform chemicals from these coffee wastes. To achieve this, biomass characterization was carried out using proximate analysis, ultimate analysis and structural analysis. Hydrothermal valorization was carried out at a temperature range of 120-180 °C (LHW) and 180-260 °C (HTC) for one hour, the platform chemicals obtained were quantified by HPLC-IR, monitored by pH and conductivity, and the solid fraction was characterized by monitoring the functional groups in IR spectroscopy, and elemental analysis. Hydrolysis processes were obtained from 150 °C, production of platform chemicals from 180 °C and maximum concentration at 180 °C-4h, over 200 °C degradation of the products in the liquid fraction starts to take place. Homogeneous basic and acid catalysts were used to improve the yields of the reaction. The kinetics of the hydrolysis of lignocellulosic structures to sugars were also analyzed and described, and reaction orders of 1 (LHW), 3 (HTC) and their respective reaction rate equations were reported.

There is a need to find methods to intensify the anaerobic digestion process. One possibility is the use of pre-treatment techniques. Many laboratory tests confirm their effectiveness, but in most cases, there is no verification work carried out on industrial plants. The aim of the research carried out under laboratory conditions and on a large scale was to determine the technological and energy efficiency of the use of hydrodynamic cavitation in the pre-treatment of a waste mixture from dairy farms. It has been shown that hydrodynamic cavitation significantly increases the concentration of organic compounds in the dissolved phase. In the most effective variants, the increase in the content of these indicators was over 90% for both COD and TOC. The degree of solubilisation achieved was 49±2.6% for COD and almost 52±4.4% for TOC. Under laboratory conditions, the highest effects of anaerobic digestion were achieved after 10 minutes of pre-treatment. The amount of biogas was on average 367±18 mL/gCOD and the amount of methane 233±13 mL/gCOD. Further large-scale optimisation trials showed that after 8 minutes of hydrodynamic cavitation, the biogas yield was 327±8 L/kgCOD with a CH4 content of 62.9±1.9%. With this variant, the net energy yield was 66.4±2.6 kWh/day, a value that was 13.9% higher than the original variant with 10 minutes of disintegration and 3.1% higher than the variant without pre-treatment.

This paper examines the relationship between GDP per capita and waste generated in European Union countries, highlighting the importance of this relationship for understanding the environmental consequences of economic growth and formulating waste management policies. The analysis findings demonstrate that, in most cases, higher GDP is associated with higher amounts of waste, although there are exceptions to this trend. A smaller number of countries are also found where no such relationship exists. These are primarily high-income countries in the lower part of the EKC or countries in transition. Cluster analysis reveals regional differences in the relationship between GDP and waste that the economic factors and the level of development in the regions concerned can explain. Bulgaria is among the European countries with the lowest economic growth associated with a large amount of waste. The analysis, therefore, focuses on Bulgaria. The impact of GDP per capita, Human Development Index and Population Density on municipal waste in Bulgaria is studied. The aim is to identify significant relationships and dependencies between these factors and the amount of waste. Based on the results of multiple regression analysis and the findings from municipal waste management data in Bulgaria, specific actions are proposed for municipal waste management in the country. Recommendations are made for developing sustainable waste management policies and sharing best practices between regions.

Aluminum, a contentious trace element found in the environment, has been demonstrated to have harmful effects on both humans and animals. In contrast, Sempervivum tectorum, an evergreen plant, has been found to offer numerous beneficial effects for both humans and animals. Therefore, this study aims to assess the protective effect of S. tectorum on certain reproductive biomarkers in male rats exposed to aluminum. Thirty-five Wistar rats were randomly divided into five groups: NTC (no-treatment control) received distilled water; NC (negative control) received drinking water containing 1 mg/L aluminum sulfate (AS); E1 received 1 mg/L AS along with an 8% S. tectorum extract; PC (positive control) received only 8% S. tectorum extract; E2 received 1 mg/L AS for three months followed by 8% extract for one month. The study analyzed testosterone, LH, FSH, body weight, and the histological structure of the testis, epididymis, and prostate, as well as the levels of zinc, manganese, copper, and iron in these organs. Significant decreases in body weight, testis, and epididymis size were observed in the aluminum-exposed groups compared to the control, whereas these decreases were not significant in the S. tectorum-treated groups compared to the control. Aluminum exposure led to significant decreases in testosterone and LH levels, with FSH levels showing a non-significant decrease in males, which were mitigated significantly by the administration of the plant extract. Histological analysis revealed alterations in the testis, epididymis, and prostate of the AS-exposed groups, including necrosis of seminiferous tubule epithelium and Leydig cells in the testis, and basal epithelial necrosis in the epididymis and prostate. Aluminum levels increased in all organs studied, while levels of zinc, copper, iron, and manganese decreased, showing a negative and significant correlation with aluminum levels. The aqueous extract of S. tectorum demonstrated a protective effect on certain studied biomarkers in male rats affected by aluminum exposure.

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

Ghana Tamale's current waste management system is overwhelmed by the growing waste crisis, necessitating the exploration of Waste-to-Energy technologies as an innovative solution. This study explores challenges and opportunities for integrating Waste-to-Energy (WtE) technologies into Tamale's existing waste management system. Qualitative research identified policy hurdles, financial constraints, social concerns, and institutional weaknesses as key barriers. Conversely, stakeholder collaboration, public education, and capacity building emerged as some success fac-tors. A proposed implementation plan emphasizes feasibility studies, public engagement, pub-lic-private partnerships (PPPs), and technology selection based on waste composition. Addition-ally, a novel framework for WtE integration within a broader Integrated Solid Waste Manage-ment (ISWM) system is presented. This framework incorporates waste sorting, recycling, WtE alternatives, and responsible management of residuals. Validation by key stakeholders con-firmed the framework's potential to improve waste management in Tamale. By overcoming identified challenges and implementing the proposed framework, Tamale can achieve environ-mental sustainability, energy generation, and progress towards UN SDGs 7, 11, and 12. This re-search offers valuable insights for policymakers and paves the way for a cleaner and more sus-tainable future for Tamale, potentially serving as a model for other developing cities.

The wealth of data obtained during the past 20 years using Laser-Induced Breakdown Spectroscopy (LIBS) indicates that the technique is very promising to detect small chemical contents of alloying elements. The potential of LIBS was looked more seriously during the past two decades or so as more data were obtained on Aluminum and steel to study the phenomena in the condition of local thermodynamic equilibrium and time-delay between a Q-switch laser and an intensified CCD camera. Since the past decade, some data on compounds were also shown to be useful in determining small concentrations of harmful elements. This manuscript is intended to show that the technique of LIBS performance is very promising in fields such as micro-machining, in alloying element analysis, surface cleaning and environmental applications even with lightweight spectrometers having a relatively low resolution, which can potentially be air-borne.

This work communicates analysis of aluminum monoxide, AlO, laser-plasma emission records using line strength data and the ExoMol astrophysical database. A nonlinear fitting program computes comparisons of measured and simulated diatomic molecular spectra. Predicted cyanide spectra of the AlO, ${\rm B}\ ^2\,\Sigma^+ \longrightarrow {\rm X} \ ^2\,\Sigma^+$, $\Delta {\rm v} = 0, \pm 1, \pm 2, + 3$ sequences and progressions compare nicely with 1 nanometer resolution experimental results. The analysis discusses experiment data captured during laser ablation of Al$_2$O$_3$ with 266-nm, 6-mJ pulses. The accuracy of the AlO line strength data is better than one picometer. This work presents as well comparison of the $^{27}$Al$^{16}$O line strength and of ExoMol data for spectral resolutions of 0.1nm and 0.07nm. Accurate AlO databases show a volley of applications in laboratory and astrophysical plasma diagnosis.

Inadequately managed agricultural waste significantly impacts the environment, health, and economy. This form of pollution arises from the underutilization, poor awareness, and insufficient treatment of agricultural waste. Fruit and vegetable wastes are valuable sources of bioactive compounds. This study aims to revalorize discarded waste from red habanero chili peppers (Capsicum chinense) by extracting bioactive compounds through different extraction processes: maceration (ME), maceration assisted by ultrasound (US), Soxhlet extraction (SE), supercritical fluid extraction (SFE), and supercritical fluid extraction with a co-solvent (SFEC). Extraction processes have significant effects on extraction efficiency and phytochemical profile (capsaicinoids and carotenoids recovery). The results indicate that the highest efficiency process is obtained with SFEC, also a high phytochemicals recovery (14.9 mg of total capsaicinoids and total carotenoids 292.09 µg per gram of sample). Concerning to phytochemical profile in the extract, the maceration process gets the highest concentration of compound followed by US and SFEC. These data reveal that the use of SFE and SFEC extraction is recommended for extraction of phytochemicals with biologically activity from red habanero chili pepper waste for diverse industries application.

This study aims to explain individual engagement in sustainable waste management behaviors (SWMBs) based on the application of protection motivation theory (PMT). SWMBs include waste avoidance, green purchasing behavior, reuse and recycle, and waste disposal behaviors. This study applies PMT to explore how individuals’ SWMBs are influenced by their perceived threats caused by environmental contamination from waste disposal and their perceived coping capability. The Bangkok metropolitan area was selected as a case study because it has faced serious waste management problems caused by massively increasing amounts of solid waste during the last ten years. Questionnaire surveys were conducted with 193 public and private officers residing in the city of Bangkok. The one-way analysis of variance (ANOVA) was performed to justify the effect of individual threat appraisal and coping appraisal on the engagement in SWMBs. The results demonstrated that respondents’ self-efficacy highly influenced all types of SWMBs. The perceived probability of being impacted from pollutants influenced all of the SWMBs except green purchasing behaviors. Response efficacy did not influence all SWMBs; however, the perceived severity of adverse consequences caused by pollutants highly influenced reuse and recycle behaviors. It could be suggested that PMT is well suited for investigating low-cost and simple SWMBs. It could also be suggested that different communication campaigns should be established to enhance citizens’ engagement in each type of SWMB.

Singapore, being a land-scarce country, is heavily dependent on imported food, which poses a challenge in ensuring food security. In addition, the substantial amount of food waste generated in Singapore further deepens food insecurity challenges, imposing enormous pressure on the country's food and land resources. In the recent years, valorising food waste streams into higher value products has been an increasing trend in tackling food wastage due to its economical and environmental benefits. This paper provides a thorough review on food waste valorisation in Singapore and summarizes critical information from the current food landscape to the food waste management strategies adopted. The review highlights the prototypes developed from food waste streams by the local research and development capabilities and the technological processing and techniques used for versatile applications ranging from food and nutraceuticals to urban agriculture. The challenges associated with the valorisation of food waste are also addressed. Two ambitious Initiatives by the Singapore government Zero Waste Plan and the 30-by-30 food security goal to encourage food waste valorisation are explored and presented. The review serves as a reference for other countries in ensuring food security and achieving sustainable development goals.

Waste-to-Hydrogen (Wahh) is a process of converting waste into hydrogen gas through various methods such as thermal conversion, biological conversion, and chemical conversion. This process not only helps in managing waste but also provides a clean source of energy as hydrogen is a renewable energy source that produces zero greenhouse gas emissions during combustion. Wahh has the potential to provide a sustainable solution for energy generation and waste management in the current scenario of globally increasing energy demands. This study aims to examine the properties and energy efficiencies of various renewable fuels including fuelwood, biogas, biomethane, and biohydrogen with a specific focus on differentiating the characteristics of biohydrogen. The paper explores the emerging concepts of waste-to-hydrogen microgrids, biohydrogen refineries, biohydrogen prosumer networks, and a biohydrogen circular economy, as well as Public-Private-People Partnerships (4Ps) and the hydrogen-centric renewable energy revolution, which are taking shape in industrialized countries. The study presents a comprehensive feasibility analysis of these concepts in the context of Nepal. The results of this research will provide valuable insights into the potential for adopting these innovative technologies in Nepal and will contribute to the development of a sustainable and efficient energy system.

Currently, there is a tenacious need to find new ways to purify water by eliminating bacterial biofilms, textile dyes, and toxic water pollutants. These contaminants pose significant risks to both human health and the environment. To address this issue, in this study, we have developed an eco-friendly approach that involves synthesizing Cobalt-doped Cerium Iron Oxide (CCIO) nanocomposite (NC) using an aqueous extract of Gossypium arboreum L. stalks. The resulting nanoparticles can be used to effectively purify water and tackle the challenges associated with these harmful pollutants. Nanoparticles excel in water pollutant removal by providing high surface area for efficient adsorption, versatile design for simultaneous removal of multiple contaminants, catalytic properties for organic pollutant degradation, and magnetic features for easy separation, offering cost-effective and sustainable water treatment solutions. CCIO nanocomposite has been synthesized by green co-precipitation method due to biomolecules and co-enzymes present in the aqueous extract of Gossypium arboreum L. stalk; a single-step procedure completed in 5 h reaction time. Further, the synthesis of nanocomposites was confirmed by various characterization techniques such as Fourier-transform infrared (FT-IR) spectroscopy, X-ray diffraction (XRD), Field emission scanning electron microscopy (FE-SEM), Transmission electron microscopy (TEM), Thermogravimetric analysis (TGA), Dynamic light scattering (DLS), and Energy Dispersive X-Ray (EDX). CCIO NCs were discovered to have a spherical shape and an average size of 40 nm. Based on DLS zeta potential analysis, CCIO NCs were found to be anionic. Also, CCIO NCs showed significant antimicrobial and antioxidant activity. Overall, considering the physical and chemical properties, the application of CCIO NCs in the adsorption of various dyes (~91 %) and water pollutants (chromium = ~ 60 %) has been considered since they exhibit great adsorption capacity owing to their microporous structure which can be a step forward in water purification.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

Within the past few decades, thousands of experiments have been performed to characterize waste and biomass to estimate the bioenergy potential and product identification. There is a need to develop an integrated process model based on experimental literature, and simulation to obtain suitable products. In this study municipal solid waste (MSW) characterization and integrated process model have been developed to optimize final products in a reactor system. The process model has two modes R&D and reactor control (RC) to obtain suitable products including bio-oil, char, and gases. A database was integrated based on thermokinetics, machine learning and simulation models to optimize product efficiency. The experimental data includes thermogravimetric analysis, Fourier transform Infrared Spectroscopy, Gas chromatography, and Mass spectrometry, which are linked with pyrolysis experimental setup. Feedstock-product mapping models were incorporated into the database along with the temperature, heating rates, elemental analysis, and final product concentration, which are utilized for pyrolysis reactor setup. Product feasibility is conducted based on lifecycle cost, affordability, and product efficiency. The present work will bridge the gap between experimental study and decision making based on obtained products at several experimental conditions around the world.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Background: Aluminum phosphide (AlP), also known as “rice tablet,” is widely used as an effective pesticide. However, AlP poisoning is a common cause of mortality in many countries, such as Iran. Unfortunately, there is no specific antidote for AlP toxicity to date. AlP releases phosphine gas when it is exposed to moisture and acid. Phosphine is a robust mitochondrial toxin that could significantly inhibit cellular energy metabolism. AlP poisoning is an emergency condition that needs instant and effective intervention. Dihydroxyacetone (DHA) is a simple saccharide used for several pharmacological as well as cosmetic purposes. Previously, we found that DHA could significantly prevent mitochondrial impairment induced by toxic agents such as cyanide and phosphine in various in vitro and in vivo experimental models.Methods: Hospitalized patients (n = 111) were evaluated for eligibility criteria. Among these patients, n = 35 cases were excluded due to incomplete data (n = 11) and suspicion of poisoning rather than AlP (n = 24). Meanwhile, n = 76 cases with confirmed AlP poisoning were included in the study. AlP-poisoned patients who did not receive DHA (n =18) were used as the control group.Patients (n = 58) received at least one dose of DHA (500 ml of 5% DHA solution w/v, i.v.) in addition to routine treatment of AlP poisoning. Arterial blood gas (ABG), blood pH, bicarbonate levels, and other vital signs and biochemical measurements were monitored. Moreover, the mortality rate and time of hospitalization were evaluated in both DHA-treated (n = 58) and AlP-poisoned patients without DHA administration (n = 18). Several biomarkers were assessed before (upon hospitalization) and after DHA treatment. The routine tests for AlP-poisoned patients in this study were the measurement of electrolytes (K+ and Na+), WBC, RBC, hemoglobin, INR, carbonate (HCO3), blood pH, PaCO2, and PaO2 and SGPT, SGOT, BUN, Cr. Results: Upon patients' admission, significant decreases in blood pH (acidosis), blood PaO₂, and HCO₃ levels were the hallmarks of AlP poisoning. It was found that DHA significantly alleviated biomarkers of AlP poisoning and tremendously enhanced patients’ survival rate compared to patients treated based on hospital routine AlP poisoning protocols (no DHA). No significant adverse effects were evident in DHA-treated patients in the current study.Interpretation: These data suggest that parenteral DHA is a novel and effective antidote against AlP poisoning.Trial registration: IR.SUMS.REC.1394.102

Since the first generation of 7xxx superhard aluminum alloy was investigated in 1930, hitherto the fifth generation aluminum alloy materials with high comprehensive properties such as high static strength, high strength, heat resistance, high toughness, damage resistance, low density and low quenching sensitivity have been improved and developed. This paper reviews the progress of 7xxx aluminum alloy materials in composition, microstructure, properties, preparation methods, heat treatment strengthening and applications from 2014 to 2021. The effect of adding trace elements on microstructure and properties of 7xxx series alloy and the problems existing in aging precipitation characteristics and reinforcement mechanism are discussed. The future development direction of 7xxx superhard aluminum alloy is prospected by optimizing heat treatment technological, adding appropriate trace elements to alloy and controlling alloy microstructure.

Water pollution is the main problem in the current scenario which is being faced by mankind due to the industrial and commercial effects. Industrial effluents contain heavy metals and inorganic ions like nitrates and phosphate ions. These ions are being included in waterways through industrial runoff. When the concentration of these hazardous pollutants increases in aquatic flora and fauna causes severe health problems. So remediation of these toxicants from water reserves is of chief importance. Conventional processes along with modern processes are being used for the treatment of industrial wastes. Photo-degradation is a modern method used for the degradation of inorganic ions due to its environmentally friendly nature and cost-effectiveness. In a recent study Aluminum oxide (Al2O3) nanoparticles were synthesized via a green approach at different pH by using Cymbopogan citratus (lemongrass) plant extract and these nanoparticles were used for the removal of inorganic ions from wastewater. The nanoparticles of different pH showed different % degradation of the inorganic ions in acidic medium removal of inorganic waste was less, in basic media % degradation was more as compared to acidic media but maximum % degradation was observed in neutral media like that average % degradation 91% and 81% was observed for nitrate and phosphate ions. The maximum absorbance occurred at 212nm and Al2O3 nanoparticles showed absorbance from 210nm-217nm. The R2 values of pseudo1st, 2nd, and BMG models were 0.956, 0.837, 0.7007 0.95, 0.896, and 0.756 for the nitrate and phosphate ions. Characterizations of synthesized particles were investigated by using UV-visible spectroscopy and other analytical methods like X-ray diffraction (XRD) and Fourier transform infrared spectroscopy (FTIR). The statistical analyses were done using Simple Linear regression (SLR).

The chelating aluminum complex [2-(Me2NCH2)C2B10H10]AlX2 (X = Br 3, CH3 4) was synthesized using 2-dimethylaminomethyl-o-carboranyl lithium (2) with aluminum tribromide or dimethylaluminum bromide, resulting in a modest yield. Compound 4 was obtained by reacting compound 3 with CH3Li in toluene. All compounds were characterized by infrared (IR) spectroscopy, 1H, 11B, 13C nuclear magnetic resonance (NMR) spectroscopy, and X-ray crystallography. X-ray structural studies of CabNAlBr2 (3) and CabNAlMe2 (4) indicated that the Al atom was located at the center of a distorted tetrahedron. Crystal structures of the CabNAlBr2 (3) [a = 8.9360(3) Å, b = 12.0358(9) Å, c = 14.7730(4) Å, α = β = γ = 90°] and the CabNAlMe2 (4) [a = 8.9551(3) Å, b = 11.9126(9) Å, c = 14.7711(4) Å, α = β = γ = 90°] were obtained. The reactivity of aluminum complexes 3 and 4 with Lewis bases, such as H2O, pyridine, alkylamines, and arylamines, confirmed their rapid decomposition.

Sharing the same raw material, recycling and composting are in direct conflict with incineration of municipal solid waste in combined heath and power plants. Indeed, waste-to-energy plants in regions with high recycling rates import urban waste from other countries to use otherwise unused capacity, and raise revenues. Using the case of Italy’s second largest and economically most developed region, I discuss the economic viability of municipal solid waste incineration to produce electricity and heath in the context of the increasing role of electricity production from renewable energy sources as well as of the emerging mass-scale uptake of bioplastics. Four lessons and three guidelines aimed to local authorities and policy makers emerge from the present study.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

Sodium-potassium (NaK) liquid alloy is a promising candidate for use as anode material in sodium batteries because of its fluidity, which effectively suppresses the growth of sodium or potassium dendrites. However, the poor wettability of the NaK liquid alloy on conventional metal substrates is unfavorable for cell fabrication due to its strong surface tension. In this paper, low-density and low-cost fluorinated aluminum foam is used as a substrate support material for NaK liquid alloy. By combining low surface tension NaK@C with fluorinated aluminum foam, we obtain a uniformly distributed and structurally stable electrode material. The composite electrode has a cycling stability of more than 3000 hours in a symmetrical cell. Furthermore, when coupled with a sulfurized polyacrylonitrile cathode in carbonate electrolyte, it maintains excellent stability even after 800 cycles, with 72% of capacity retention.

Turbulent flow is the first and fundamental physical phenomena to evaluate when optimising cost and reducing emissions from an Anode Baking Furnace (ABF). Gas flow patterns, velocity field, pressure drop, shear stress, and turbulent dissipation rate variables are the main operational parameters to be optimised, considering a specific geometry. Computational Fluid Dynamics (CFD) allows simulating physical phenomena using numerical methods with computer resources. In particular, the finite element method is one of the most used methods to solve the flow equations. This method requires a discretisation of the geometry of the ABF, called mesh. Hence, mesh is the main input to the finite element method. A suitable mesh for applying a discretisation method determines whether the problem can be simulated or not. Generating an appropriate mesh remains a challenge to perform accurate simulations. In this work, a comparison between meshes generated using two mesh generation tools is presented. Results of different study cases are included.

The global food system has three recognized challenges: (a)increasing the availability of food consumption, (b) reducing food loss, and (c) reducing food waste. The increasing demand for food consumption, increasing quantity of food loss, and corresponding increase in food waste are resulting in serious health, aesthetic, social, economic, and environmental problems due to a lack of appropriate planning and management. Despite its importance, there is no clear, concise, and comprehensive definition of food consumption, loss, and waste. Generally, food consumption, food loss, and food waste are dealt with separately. This article presents a logically constructed ontological framework of food consumption, loss, and waste. It gives equal importance to all three aspects of global food management. The systematic ontological framework is general, and the analysis can be applied to any country. The framework deconstructs the combinatorial complexity of the problem and explicates the pathways to manage the consumption, loss, and waste. The ontological framework encapsulates 19*8*7*4*5*6 = 25,536 possible components of the challenge. A critical analysis based on available data using the framework will help to develop strategies to deal with the problem. It can help to discover the gaps and to find ways to bridge the gaps. It is novel to conceptualize food consumption, loss, and waste together.

The city of Lisbon, has any other capital of a European country, has a large number of issues while managing the waste and recycling containers spread throughout the city. This document presents the results of a study promoted by the Lisbon City Council for trialing LPWAN technology on the waste management vertical under the Lisbon Smart City initiative. Current waste management is done using GSM sensors, and the aim is to use LPWAN to reduce the costs, improve range and reduce provisioning times when changing the communications provider. After an initial study, LoRa was selected as the LPWAN of choice for the trials. The study is composed of multiple use cases at different distances, types of recycling waste containers, placements (underground and surface) and different kinds of waste level measurement LoRa sensors, deployed in order to assess the impact of the different use cases on the LoRa sensor usage. The results shown that the underground waste containers present the most difficult challenge, where the container itself imposes attenuation levels of 26dB on the link budget. The results promoted the deployment of a city wide LoRa network available to all departments inside the Lisbon City Council, and considering the network capacity the network, the network is also available to citizens to be used freely.

This paper reports the effect of silicon substrate orientation and aluminum nitride buffer layer deposited by molecular beam epitaxy on the growth of aluminum nitride thin films deposited by DC magnetron sputtering technique at low temperature. The structural analysis has revealed a strong (0001) fiber texture for both substrates Si (100) and (111) and a hetero-epitaxial growth on few nanometers AlN buffer layer grown by MBE on Si (111) substrate. SEM images and XRD characterization have shown an enhancement in AlN crystallinity thanks to AlN (MBE) buffer layer. Raman spectroscopy indicated that the AlN film was relaxed when it deposited on Si (111), in compression on Si (100) and under tension on AlN buffer layer grown by MBE/Si (111) substrates, respectively. The interface between Si (111) and AlN grown by MBE is abrupt and well defined; contrary to the interface between AlN deposited using PVD and AlN grown by MBE. Nevertheless, AlN hetero-epitaxial growth was obtained at low temperature (<250°C).

Large aluminum alloy ring forgings are the core components of heavy-duty rocket fuel storage tanks, and the large residual stress inside the rings leads to poor shape accuracy of large thin-walled parts. The initial stress of the 2219 aluminum alloy ring blank was tested using the drilling method, and the creep constitutive coefficient of the 2219 aluminum alloy was determined through stress relaxation tests. The numerical simulation processes of thermal stress relief (TSR), vibration stress relief (VSR), and thermal-vibration stress relief (TVSR) were compared and established. Through the correlation analysis between the actual measurement results of residual stress and the simulation results, it can be seen that the strong correlation in three directions at each measurement point accounts for over 37.5%, and the moderate correlation accounts for over 62.5%. This indicates that the numerical simulation model of 2219 aluminum alloy ring containing initial residual stress can accurately reflect the size and distribution of residual stress inside the actual ring. The simulation results show that the derived constitutive model can describe the stress relaxation process of TVSR by combining a single thermal time effect stress relaxation constitutive theory with a VSR plastic deformation material model. The simulation models established above were used to calculate the residual stress homogenization ability of three types of aging. The results showed that VSR, TSR, and TVSR can homogenize and reduce the residual stress field inside the ring, improve the distribution of residual stress inside the ring, and have a better overall homogenization ability of TVSR. The VSR control has a certain effect on reducing and homogenizing residual stress, but compared with TSR and TVSR, the reduction and homogenization ability of residual stress control is limited. The homogenization control effect TVSR>TSR>VSR, and the maximum equivalent stress homogenization rates of VSR, TSR, and TVSR are 52.8%, 80.6%, and 82.2%, respectively. Then, numerical simulation technology is used to study how the initial residual stress in the blank will cause the deformation of the ring during the thin-walled machining process. The roundness error theory of the minimum containment area method is applied to evaluate the deformation degree during the thin-walled numerical machining process, and the TVSR method is used for stress regulation. The deformation law of the thin-walled machining of the ring under different aging parameters is studied.

Valorization of food and fruit wastes has the potential for the production of sustainable energy and biochemicals. Approximately 70% of the weight of the original jackfruit (Artocarpus heterophyllus L.) fruit is lost during processing as waste in the form of peeled skin and core, both of which have not been utilized and, thus contribute to disposal as well as pollution issues. The major components, cellulose, and hemicellulose, can be biologically transformed easily into bioenergy sources like ethanol, methanol, and butanol; valuable phenolics and biotechnological products like pectin, citric acid, bromelain, ferulic acid, and vanillin; and many other products. These residues can also be utilized as essential sources for the biological transformation process leading to the production of numerous products with added value, such as phenolic antioxidants, phenolic flavor compounds, and organic acids. Thus, the value addition of jackfruit waste can support the sustainable solution towards food and nutritional security. In this way, zero waste can be achieved through novel biorefineries which are critically highlighted in this paper. Furthermore, novel technologies for the conversion of jackfruit wastes are summarized with recent findings.

Aluminum (Al) and manganese (Mn) toxicity are the top two constraints to crop production in acid soil. Crops have evolved common and specific mechanisms to tolerate the two stresses. In the present study, the responses (toxicity and tolerance) of wheat near-isogenic lines (ET8 and ES8) and their parents (Carazinho and Egret) to Al and Mn were compared by determining physiolog-ical parameters and transcriptome profiling of roots. The results showed that: (1) Carazinho and ET8 exhibited dual tolerance to Al and Mn as compared with Egret and ES8, indicated by higher relative root elongation and SPAD; (2) After entering into roots, Al was mainly distributed in the root and fixed in the cell wall, while Mn was mainly distributed in the cell sap and then trans-ported to leaves. Both Al and Mn stresses decreased the contents of Ca, Mg, and Zn; Mn stress al-so inhibited the accumulation of Fe, while Al showed an opposite effect; (3) Transcriptomic analy-sis identified 5581 differentially expressed genes (DEGs) under Al stress and 4165 DEGs under Mn stress. Among these, 2774 DEGs were regulated by both Al and Mn stresses, while 2280 and 1957 DEGs were exclusively regulated by Al and Mn stress, respectively. GO and KEGG analyses indi-cated that cell wall metabolism responds exclusively to Al, while nicotianamine synthesis exclu-sively responds to Mn. Pathways such as signaling, phenylpropanoid metabolism, and metal ion transport showed commonality and specificity to Al and Mn. TFs, such as MYB, WRKY, and AP2 families, were also regulated by Al and Mn, and WGCNA identified PODP7, VATB2, and ABCC3 as the hub genes for Al tolerance and NAS for Mn tolerance. The identified genes and pathways can be used as targets for pyramiding genes and breeding multi-tolerant varieties.

To obtain a given structure in 3D building-up modes, it is necessary to use optimal surfacing modes that determine the amount of heat input in local areas. For this purpose, aluminum bronze was surfacing onto a deformed base and the structure and its characteristics in the surfacing and heat-affected zones were studied by the EBSD method. The heterogeneity of the formation of the structure in each selected zone is established, which indicates the heterogeneity of heat input in local areas of the material in one mode of surfacing. For typical cases of crystallization, a molecular dynamics simulation of crystallization processes with different heat input to the base with characteristics specified based on experimental data was carried out. It has been established that the amount of heat input determines the degree of melting and the inherited defectiveness of growing crystals. The formation of misorientation boundaries and crystallization centers of new grains is determined by the conditions of joint growth of grains with given crystallographic parameters of the computational model. Numerical calculations agree with the experimentally observed results.

Sugarcane is an important sugar-source crop. As any other plant, it can be exposed to several abiotic stress conditions. Though some metals contribute to critical physiological processes in plants, the presence of aluminum ions (Al3+) can be very toxic. In order to develop plants that flourish in acidic soils, it is critical to gain insights into the molecular mechanisms of sugarcane response to aluminum stress. To determine the genes involved in sugarcane response to aluminum stress we generated 372 million paired-end RNA sequencing reads, from roots of CTC-2 and RB855453 two contrasting cultivars. Data normalization resulted in 162,161 contigs and 97,335 trinity genes. After the read cutoff, the differentially expressed genes were 4,858 in CTC-2 and 1,307 in the RB855453, Treatment Vs Control, respectively. The differentially expressed genes were annotated into 34 functional categories. The majority of the genes were upregulated in the CTC-2 (tolerant cultivar) and down regulated in RB855453 (sensitive cultivar). Here, we present the first root-transcriptome of sugarcane under aluminum stress. The results and conclusions of this study provide a valuable resource for future genetic and genomic studies in sugarcane. This transcriptome analysis points out that sugarcane tolerance to aluminum may be explained by an efficient detoxification mechanism combined with the lateral root formation and activation of redox enzymes. Following our results, we present here, a hypothetical model for the aluminum tolerance in CTC-2 cultivar.

Safety assessment of structures can be obtained employing limit design to overcome uncertainties concerning actual response due to inelastic constitutive behavior and more generally to non-linear structural response and loads’ random variability. The limit analysis is used for evaluating the safety of the structures directly starting from load level without any knowledge of the load history. In the paper, the lower bound calculation is proposed where a new strain-based approach is used that allowed describing the residual stress and displacement in terms of permanent strain. The strategy used the permanent strain as the effective parameters of the procedure so that it was possible to assess the ductility requirements for the complete load program developed till collapse or shakedown. The procedure is compared to experimental results obtained on aluminum beams in shakedown.

Solid waste management is a global issue that affects every individual living in the world directly or indirectly. Failing to manage the waste properly will cause harm on public health, our natural environment, and even our happiness and prosperity. When asked about the reason behind the failure of third time plastic ban in Bhutan, one of the Bhutanese said it’s because of the lack of cooperation from public to support the move of government. Clean Bhutan, a non-governmental organization (NGO) that aims Zero Waste Bhutan by 2030, has collected around 5,900 metric tons of waste from December 2014 to February 2018. This project will create some awareness regarding the management of waste at individual level when people come in contact with the family of the researcher. It also talks abot how waste management and biodiversity conservation can go side by side.

A special vibration damper is proposed for material property identification through a scratching process on a vibrating object. This paper presents the design and working principle of a scratching damper based on a scratch test device. A non-contact electromagnetic shaker is used to generate the shaking force for the vibration of the tested object. The required pressure on the scratched material during the scratching process is generated by a compression spring and adjusted by changing the amount of compression of the spring. The proposed damper is designed and tested on extruded aluminum samples for the determination of its Young’s modulus and hardness and validated by using the standard test instruments. Observations of physical dimensions of the scratching tracks are determined by microscope and were utilized to compute the scratching energy factor. Load curves are obtained at different pressure of the scratching process. The hysteresis loop energy during the scratching process of the tested object is measured and used for the determination of material properties of the object. Furthermore, energy conservation law, scratch energy release rate and loop energy release rate are used to determine the Young’s modulus and hardness of the sample. The measurement accuracy of the modulus and hardness of the tested sample is evaluated. The proposed method of material testing has several advantages over the traditional methods such as low cost and high repeatability, and may be used as an alternative to the standard modulus and hardness testers.

Aluminum (Al) toxicity is the most common factor limiting the growth of alfalfa in acidic soil conditions. Melatonin (MT), a significant pleiotropic molecule present in both plants and animals, has shown promise in mitigating Al toxicity in various plant species. This study aims to elucidate the underlying mechanism by which melatonin alleviates Al toxicity in alfalfa through a combined physiological and transcriptomic analysis. The results reveal that 5 μM MT significantly alleviates Al-induced growth inhibition and preserves the morphology of root tip cells. Moreover, MT application reduces Al accumulation in alfalfa roots and shoots by 28.6% and 27.6%, respectively. Additionally, MT plays a crucial role in scavenging Al-induced excess H2O2 by enhancing the activities of superoxide dismutase (SOD), peroxidase (POD), and catalase (CAT), consequently reducing malondialdehyde (MDA) levels. The RNA-seq results reveal that MT application significantly upregulates the expression of xyloglucan endotransglucosylase/hydrolase (XTH) and carbon metabolism-related genes, including those involved in the glycolysis process, as well as sucrose and starch metabolism, suggesting that MT application may mitigate Al toxicity by facilitating the binding of Al to the cell walls, thereby reducing intracellular Al accumulation, and by improving respiration and the content of sucrose and trehalose. Taken together, our study demonstrates that MT alleviates Al toxicity in alfalfa by restoring redox homeostasis, enhancing Al binding to the cell wall, and modulating carbon metabolism. This research advances our understanding of the mechanisms underlying MT's effectiveness in mitigating Al toxicity, offering potential strategies for reducing Al accumulation in alfalfa.

Structural evolution, mechanical and tribological properties of Al-Mg alloy admixed with 5, 10 and 15 vol.% of iron powder using multi-pass friction stir processing (FSP) have been studied. Homogeneous distribution of intermetallic compound (IMC) particles were achieved after 4 FSP passes what resulted in increasing the stir zone hardness and ultimate tensile stress with simultaneous loss in the ductility. The reinforcement of the aluminum alloy matrix with IMCs allowed reducing wear at the same magnitude of friction. Subsurface composite tribological layer was formed on the FSPed samples as a result of rubbing against a steel counterbody.

In recent years, in addition to the commonly known wire-based processes of Directed Energy Deposition using lasers, a process variant using the electron beam has also developed to industrial market maturity. The process offers particular potential for processing highly conductive, reflective or oxidation-prone materials. However, for industrial usage there is a lack of comprehensive data on performance, process limits and possible applications. The present study deals with this problem using the example of the high-strength aluminum bronze CuAl8Ni6. Multi-stage test welds are used to determine the physically possible process limits and draw conclusions about the suitability of the parameters for additive manufacturing. For this purpose, optimal ranges for energy input, possible welding speeds and the scalability of the process were investigated. Finally, additive test specimens in the form of cylinders and walls are produced and the hardness profile, microstructure and mechanical properties are investigated. It is found that the material CuAl8Ni6 can be well processed by wire electron beam additive manufacturing. The microstructure is similar to a cast structure, the hardness profile over the height of the specimens is constant and the tensile strength and elongation at fracture values achieved correspond to the specification of the raw material.

Al-Zn-Mg-Cu alloy has high specific strength, good corrosion resistance, fracture toughness and fatigue resistance. It is one of the most important structural materials in the fields of aviation, aerospace, weapons, transportation and so on, which plays a huge role in the field of aerospace.In order to optimize the strength, toughness and corrosion properties of Al-Zn-Mg-Cu alloy, alloying has always been the focus of research on Al-Zn-Mg-Cu alloy. The effects of main alloying elements, trace alloying elements and rare earth elements on the microstructure and properties of Al-Zn-Mg-Cu aluminum alloy were briefly introduced in the paper, and the future research directions were prospected.

Epoxy was blended with benzoxazine resin and aluminum trihydrate (ATH) additive to render flame retardancy while maintaining mechanical properties. The ATH was modified using three different silane coupling agents and then added to 60/40 epoxy/benzoxazine mixtures. The effect of blend compositions and surface modification on flame retardant and mechanical properties of the composites was investigated by UL94, tensile, and shear tests. Resin mixtures containing more than 40 wt% benzoxazine revealed a UL94 V-1 rating with enhanced tensile and shear strength. Upon addition of 20 wt% ATH to 60/40 epoxy/benzoxazine, a V-0 rating was achieved. The lowered tensile and adhesive properties of the composites in the presence of ATH were improved by modifying the ATH surface using silane coupling agents.

The supramolecular aggregation processes occurring on metallic (aluminum and gold) surfaces in aqueous solutions of bovine serum albumin (BSA) during drying were studied using advanced scanning electron microscopy (SEM). The possible mechanism for the formation of amazing intricate fractal structures on metallic surfaces was proposed based on the analysis of SEM images, size distribution diagrams and EDX-scanning elements distribution maps.

Titanium dioxide (TiO2) and aluminum oxide (Al2O3) coatings have been investigated in a wide range of bio-applications due to their biodegradation and biocompatibility properties, that are key parameters for their use in the food packaging and biomedical devices fields. The present study evaluates and compares the electrochemical behavior of the non-coated, commercial resin-coated, TiO2-coated and Al2O3-coated aluminum in commercial beer electrolyte. For this, TiO2 and Al2O3 thin films were deposited on aluminum (Al) substrates using atomic layer deposition (ALD). The evaluation of the corrosion barrier layer properties was performed by linear sweep voltammetry (LSV) and electrochemical impedance spectroscopy (EIS). In addition, profilometry, grazing incidence X-ray diffractometry (GIXRD), scanning electron microscopy (SEM) and Fourier-transform infrared spectroscopy (FT-IR) analyses were performed to investigate the physical and chemical properties of the pristine and / or corroded samples. TiO2 and Al2O3 films presented an amorphous structure, a morphology that follows Al substrate surface, and a thickness of around 100 nm. Analysis of LSV data showed that ALD coatings promoted a considerable increase in corrosion barrier efficiency being 86.3% for TiO2-coated Al and 80% for Al2O3-coated Al in comparison with 7.1% of commercial resin-coated Al. This is mainly due to the lower electrochemical porosity, 11.4% for TiO2-coated Al and 20.4% for Al2O3-coated Al in comparison with 96% of the resin-coated Al, i.e. an increase of up to twofold in the protection of Al when coated with TiO2 compared to Al2O3 coated. The EIS results allow us to complement the discussions about the reduced corrosion barrier efficiency of the Al2O3 film for beer electrolyte once SEM and FT-IR analyzes did not show drastic changes in both investigated ALD films after the corrosion assays. The above results indicate that ALD TiO2 and Al2O3 films may be a viable alternative to replace the synthetic resin coatings frequently used in aluminum cans of use in the food industry.

Aluminum is a strategic mineral resource, and China’s aluminum production and consumption is fairly large. However, its supply guarantee is uncertain because of a high dependency on external raw materials. This uncertainty may expand, so finding a way to reduce the uncertainty of aluminum resource supply is especially important. This paper applies the SFA method to analyze the aluminum flows in mainland China from 1996 to 2014, and establishes a supply structure model to measure its supply guarantee degree. The results claim that: (1) China’s aluminum production can satisfy demand and even create a surplus; (2) Domestic self-productive primary and secondary aluminum increased at an annual rate of 12% and 24%; (3) The proportion of self-productive secondary aluminum in the supply structure increased from 7.7% in 1996 to 12.8% in 2014, while that of primary aluminum decreased from 79.6% to 42.8%; (4) The total supply guarantee degree decreased from 87.3% to 55.6% in this period. These results provide a feasible way to solve this plight: the proportion of secondary aluminum in the supply structure should be enhanced, and an efficient aluminum resource recycling system needs to be established as soon as possible to ensure its sustainable supply.

This scoping review examines global strategies and enterprises for sustainable solid waste management, with a focus on alternative landfilling approaches. The study collected and analyzed a significant number of documents from different regions, revealing Asia as the major contributor (for the collected documents) (48.7%), followed by North America (24.3%) and Europe (15.8%). Recycling emerged as the most effective alternative waste treatment method, representing 52.3% of the documented approaches, with industrial recycling (22.6%) and residential/non-residential recycling (20.2%) as prominent categories. Food waste was a significant concern across regions, constituting 21.4% of the collected documents. Composting was widely adopted (15.4%) due to its simplicity and benefits for gardening and soil improvement. Other methods like biogas extraction, reusing, raising awareness, incinerating, redistributing, reducing, and fermentation accounted for 13.1% cumulatively. The study highlights the need for tailored waste management solutions based on regional challenges and successful practices. Promoting recycling infrastructure, composting, and waste reduction approaches are crucial to achieving sustainable waste management aligned with SDGs. Collaboration and knowledge-sharing between regions are essential to improve inefficient waste management mechanisms. Integrating the findings into policymaking and industry practices can lead to a more sustainable future with reduced environmental impact.

The proof-of-the-concept of application of low-temperature food waste biochars for the anaerobic digestion (AD) of food waste (the same substrate) was tested. The concept assumes that residual heat from biogas utilization may be reused for biochar production. Four low-temperature biochars produced under two pyrolytic temperatures 300 °C and 400 °C and under atmospheric and 15 bars pressure with 60 minutes retention time were used. Additionally, the biochar produced during hydrothermal carbonization (HTC) was tested. The work studied the effect of a low biochar dose (0.05 gBC x gTSsubstrate-1, or 0.65 gBC x L-1) on AD batch reactors’ performance. The biochemical methane potential test took 21 days and the process kinetics using the first-order model were determined. The results showed that biochars obtained under 400°C with atmospheric pressure and under HTC conditions improve methane yield by 3.6%. It has been revealed that thermochemical pressure influences the electrical conductivity of biochars. The biomethane was produced with a rate (k) of 0.24 d-1, and the most effective biochars increased the biodegradability of FW to 81% in comparison to variants without biochars (75%).

As the additive manufacturing industry grows, it is compounding the global plastic waste problem. Distributed recycling and additive manufacturing (DRAM) offers an economic solution to this challenge, but it has been relegated to either small-volume 3D printers (limiting waste recycling throughput) or expensive industrial machines (limiting accessibility and lateral scaling). To overcome these challenges, this paper provides proof-of-concept for a novel open-source hybrid 3D printer that combines a low-cost hanging printer design with a compression screw-based end-effector that allows direct extrusion of recycled plastic waste in large expandable printing volumes. Mechanical testing of the resultant prints from 100% waste plastic, however, showed that combining challenges of non-uniform feedstocks and a heavy printhead for a hangprinter reduced the strength of the parts compared to fused filament fabrication. The preliminary results are technologically promising, however, and provide opportunities to improve on the open source design to help process the volumes of waste plastic needed for DRAM to address the negative environmental impacts of global plastic use.

Abstract: In order to accelerate deployment of distributed recycling by providing low-cost feed stocks of granulated post-consumer waste plastic, this study analyzes an open source waste plastic granulator system. It is designed, built and tested for its ability to convert post-consumer waste, 3-D printed products and waste into polymer feedstock for recyclebots of fused particle/granule printers. The technical specifications of the device are quantified in terms of power consumption (380 to 404W for PET and PLA, respectively) and particle size distribution. The open source device can be fabricated for less than USD$2000 in materials. The experimentally-measured power use is only a minor contribution to the overall embodied energy of distributed recycling of waste plastic. The resultant plastic particle size distributions were found to be appropriate for use in both recyclebots and direct material extrusion 3-D printers. Simple retrofits are shown to reduce sound levels during operation by 4dB-5dB for the vacuum. These results indicate that the open source waste plastic granulator is an appropriate technology for community, library, makespace, fab lab or small business-based distributed recycling.

We have investigated the effect of electron-beam irradiation by a forevacuum-pressure plasma-cathode electron source on the surface roughness and hardness of Al2O3- and AlN-based ceramics. The roughness increases with increasing temperature of the processed surface, while the hardness slightly decreases. For aluminum nitride ceramic, we find that the thermal conductivity increases by a factor of 1.5 to 2 depending on the electron-beam irradiation regime.

In this article, it is proposed to use aluminum breakage scraps to obtain Green Hydrogen through the aluminum-water reaction with caustic soda as a catalyst. From this exothermic reaction, both hydrogen and the heat generated can be used. Due to the low price of aluminum chips, this allows us to produce Green hydrogen below the current price that is obtained using renewable energy sources and electrolyzers. On the other hand, we have developed a process that is sustainable since it is obtained as alumina and caustic soda waste that can be reused. This alumina obtained, once filtered, has high purity which allows us to produce high-quality primary aluminum without the need to use bauxite and reducing the production of red sludge. A comparative study-analysis has been carried out of two of the types of forms in which the most common aluminum is presented in the industry to analyze which one performs better by studying key factors such as the hydrogen produced, and the waste generated during the process. Finally, the mathematical model has been defined to be able to control the flow based on different key parameters such as temperature, molarity, and geometry. Undoubtedly, the study that we present represents a milestone for the recovery of metallic aluminum waste and may be of great interest to industries that use aluminum in their processes, such as recuperators, but also the vehicle or aerospace industry.

The aims of this work were to examine the new electrode, based on polymer bacteria modified aluminum electrode for simultaneous production of electricity and degradation of phenol. This electrode is based aluminum modified by bacteria inserted in the polymer matrix, developed in situ on the surface. This electrode, designated subsequently by bacteria-polymer-aluminum, Showed stable response and was characterized with voltametric methods, as cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). The experimental results revealed that the prepared electrode could be a feasible for degradation of hazardous phenol pollutants. The sensor was successfully applied to the determination of phenol in a real sample with satisfactory results.

Several challenges stand in the way of production of Metal Matrix Composites (MMCs) such as higher processing temperatures, particulate mixing, particulate-matrix interface bonding issues and ability to process into desired geometrical shapes. Although there are many literatures showing composites with single particulate reinforcements, the studies on composites with multiple reinforcing agents (hybrid composites) are found to be limited. Development of a hybrid particulate composite with optimized mechanical and tribological properties is very significant to suit modern engineering applications. In this study, Al-Si hypereutectic alloy (A390) is used as the matrix and Silicon Carbide (SiC) and Graphite (Gr) and Molybdenum di-Sulphide (MoS₂) are used as particulates. Particulate volume (wt%) is varied and sample test castings are made using squeeze casting process through stir casting processing route. The evaluation of mechanical properties indicates that presence of both the hard phase (SiC) and the soft phase has distinct effect on the properties of Hybrid Composite. Composite samples were characterized to understand the performance and to meet the tribological applications. Fractography study indicated an intra-granular brittle fracture for hybrid composites. Wear study shows that Hybrid MMCs has better tribological performance compared to that of A390 alloy.

This study aimed to investigate the effect of reducing the amount of organic waste on the weight of cats in Tehran. The weight of 4192 cats was measured from spring 2016 to the end of winter 2020. They were classified into 6 age groups, 2 gender groups, and 13 geographical areas. Their weight was measured for 48 months (16 seasons). The statistical parameters analysis showed no weight loss in 2017, but since 2018, cats have been losing weight every year. They had lost about 178g of their weight in 2018. The sharpest annual decrease was observed in 2019 when about 301g of weight loss was recorded. In the winter of 2020, 115g of weight loss took place. In the spring of 2017, no weight change was observed, but in the spring of 2018, the cats lost 155g of their weight. Their weight loss intensified in the spring of 2019 and about 299g of weight loss was observed. In the summer of 2017, as in the spring of the same year, no weight loss was recorded, but for the summer of 2018, the weight loss was evident and about 205g of the weight of the cats had been reduced. The weight loss in the summer of 2019 not only continued but intensified and about 304g of weight loss was recorded for cats. Weight change was not observed in the fall of 2017 as in the spring and summer of the same year. In the fall of 2018, weight loss was recorded for cats. They had lost about 324g of their weight in the fall of 2018. Also, they experienced a weight loss of about 218g in the fall of 2019. During the spring, summer, and autumn of 2017, no weight loss was observed in the cats for the winter of 2018, but in the winter of 2019, the cats faced the most severe weight loss (seasonally). They lost about 401g of weight in the winter of 2019. Of course, in the winter of 2020, about 186g of weight loss was observed in cats. The results showed that female cats did not lose weight in 2017 but experienced weight loss in 2018 with a weight loss of 181g. The weight loss of females intensified in 2019 and 294g of weight loss was recorded. Female cats lost 186g of their weight in the winter of 2020. Male cats did not lose weight like female cats in 2017. But in 2018, a weight loss of 166g was observed in male cats. The weight loss of male cats continued in 2019 and 311g of weight loss was recorded for them. However, in 2020, unlike females, weight loss was not observed in male cats. It can be said that both sexes lost more weight in the winter of 2019 than in other seasons. In 2017, weight loss was observed only for the region of 10, and in the same year, weight gain was recorded for the region of 15. But in 2018, except for regions 3, 4, 15, and 19, weight loss was observed in other regions. In 2019, the weight loss of cats spread and weight loss was observed in all regions except the region of 12. In winter 2020, weight loss was recorded only in the region of 4. In the end, it can be concluded that the weight of cats has decreased since the spring of 2018 because the beginning of the decrease in the amount of organic waste has been recorded since the winter of 2018. So, there is a direct relationship between the weight of cats and the amount of organic waste (access to food). The amount of garbage has been decreasing since the winter of 2018, and the average weight of cats has also been decreasing since the spring of 2018 due to the decrease in access to food.

The issue of sustainability has long been the subject of interest of the architecture engineering and construction sector. All three aspects of sustainability - economic, environmental and social - can be affected through appropriate construction waste management. Construction and demolition waste (CDW) is one of the largest worldwide waste streams, therefore it is given great attention by all stakeholders (investors, contractors, authorities, etc.). Researches have shown that one of the main barriers to insufficiency CDW recovery is inadequate policies and legal frameworks to manage CDW. It is also one of the EU's environmental priorities. Aim of the article is to confirm the economic potential of construction and demolition waste audit processing through case study. A pre-demolition waste audit has been processed for unused building of shopping center in the town Snina in Slovakia. Subsequently, a comparison of economic parameters (waste disposal costs and transport costs) of recommended CDW management was performed. This comparison confirmed the economic benefits of environmentally friendly construction waste management methods according to the waste audit results, which will also increase the sustainability of construction projects. In addition, the cost parameters of selected waste disposal methods could be another dimension of building information modelling.

The effects of 1%~5% cold compression on the mechanical properties, microstructure and residual stress of 7050 aluminum alloy were investigated, and the results were applied to the complex die forging with stiffener structure. The results show that with the increase of cold compression, the tensile strength of forging decreases gradually, but the conductivity and fracture toughness of the forging have little change. TEM microstructure shows that with larger cold compression (5%), the dislocation density was relatively higher, which promoted the precipitation and growth of precipitated phases at positions with higher dislocation density during aging process. The ultrasonic tests of residual stress show that with the increase of cold compression, the residual stress in the forging decreases first, and then increases when cold compression reaches 5%. The results of the die forging of 7050 aluminum alloy with bar structure show that the residual stress of the die forging is obviously eliminated after 2-4% cold compression, and the deformation after machining is obviously less than of the uncompressed forgings. The combination of bar and web is more beneficial to the uniform distribution of residual stress of the die forging with bar structure.

This study utilized electron back scattered diffraction (EBSD) and X-ray diffraction (XRD) to investigate the impact of inter-annealing temperature and heating rate of final annealing on the microstructure of high-voltage anode aluminum foils. The findings indicate that the formation of cube texture in the final products is significantly influenced by the inter-annealing temperature, as low inter-annealing temperatures retain a considerable amount of deformation stored energy, providing a strong driving force for nucleation. The cube texture is observed to deviate from the ideal position at lower inter-annealing temperatures. Additionally, an increase in heating rate during final annealing leads to a gradual decrease in the fraction and grain size of recrystallization. This is attributed to the fact that a higher heating rate (below the critical heating rate) reduces the time available for grain boundary migration, thereby slowing the recrystallization process.

There are various approaches to managing polyethylene terephthalate waste, including methods for recycling PET. However, at present, only the cleanest wastes that can already be efficiently recycled using known methods are considered in the scientific literature. The study aims to look at other forms of polyethylene terephthalate waste that pose a challenge: low quality PET flakes, polyester tire cord, PET dust and prepolymer waste. The waste was characterized by FTIR spectroscopy, viscosimetry, differential scanning calorimetry, laser diffraction and sieve analysis. The findings describe the composition and properties of various forms of polyethylene terephthalate waste. Low quality PET flake waste and polyethylene terephthalate dust have been shown to be suitable for all chemical recycling methods. When recycling waste polyester tire cord, it is difficult to completely separate the rubber, so its presence in the final product must be taken into account. The most promising way to process a prepolymer is its depolymerization by hydrolysis, alcoholysis or glycolysis to produce monomers for the synthesis of PET, similar in properties to the primary one.

The consistent and continuous growth in the world’s population is creating many challenges for public policymakers in the different life areas, including dealing with the increasing amounts of waste that are generating problems involving air and land pollution and a shortage of land for waste disposal. This study presents the results of public policy on managing municipal waste, as manifested in the quantity and rate of waste collected throughout Israel in recent years and disposed of in the various landfills and in analysis of the political and economic factors affecting this policy. The study combines a quantitative and qualitative approach, where the quantitative study includes analysis of statistical data based on information from the Central Bureau of Statistics, the Ministry of Environmental Protection, the Ministry of Finance, and others, and the qualitative study relies on reading and analyzing primary documents of the different government ministries on Israel’s waste disposal policy and information in the media on this issue. The research findings attest to an increase in the amount of municipal waste dumped in Israel, a merely slight decrease in the rate of landfilling as a proportion of all municipal waste disposal, and a merely slight increase in the rate of municipal waste recycled in recent years. The research conclusions stress the effects of the landfill levy and the Cleanliness Maintenance Fund on one hand, and of the government instability in the Ministry of Environmental Protection, the positivist policy embraced by decision makers in the Ministry of Environmental Protection, and the power struggles between Israel’s different ministries on the other, as the respective economic and political factors affecting Israeli policy on municipal waste management.

The treatment, disposal, and resource utilization of waste mud are challenges for engineering construction. This study investigates the road performance of waste mud–solidified soil and reveals the mechanism of how solidifying materials influence the strength and deformation characteristics of waste mud. Waste mud, collected from a highway reconstruction project, was mixed with ordinary Portland cement as a solidifying material. Unconfined compressive strength tests, consolidated undrained triaxial shear tests, resonant column tests, and consolidation compression tests were conducted to evaluate the solidification effect. The test results show that with an increase in cement content from 5% to 9%, the unconfined compressive strength of the waste mud–solidified soil increased by over 100%, the curing time was extended from 3 days to 28 days, and the unconfined compressive strength increased by approximately 70%. However, an increase in initial water content from 40% to 60% reduced the unconfined compressive strength by 50%. With the increase of cement content from 5% to 9%, the cohesion and friction angles increased by approximately 78% and 24%, respectively. The initial shear modulus under dynamic shear increased by approximately 38% and the shear strain corresponding to a damping ratio decay to 70% of the initial shear modulus decreased by nearly 11%. The compression coefficient decreased by approximately 55%. Scanning electron microscopy and X-ray diffraction tests showed that a higher cement content led to the formation of more hydration reaction products, especially an increase in the content of AlPO4. The bonding material between soil particles significantly increased, exerting a bonding and filling effect on soil particles and firmly adhering them together. Consequently, the strength of the waste mud–solidified soil increased significantly while its compressibility decreased.

The article provides an overview of nanocomposites and microelectronic elements used in space electronics and radiation control systems of nuclear reactors. Only those nanocomposites and microelectronic elements are taken into account that improve their characteristics in radiation fields or remain indifferent when exposed to ionizing radiation. Considering the chemical composition of the materials of these nanocomposites and microelectronic elements, it is analyzed from which radioactive materials (RM) obtained by recycling radioactive waste (RW) such composites and microelectronic parts can be made. Thus, an alternative way of radioactive waste disposal is proposed, when these wastes are used in the form of microelectronic elements designed to operate under conditions of cosmic radiation.

Introduction: Pharmaceutical products are inevitable for human health. Owing to the growing need for pharmaceuticals, pharmaceutical companies introduce drugs annually into the market in addition to the extensive collection of existing pharmaceutical products. Households, farms, health facilities, and pharmaceutical industries release pharmaceutical waste into the environment at low concentrations through routine pharmaceutical use, damage, and expiry. The effects of active pharmaceutical ingredients (API) on non-target species in the environment are not known. Over the years, pharmaceuticals such as diclofenac and ibuprofen in trace amounts have been detected in public water systems, ground and surface water. Unwanted medicines should be safely disposed of at a reduced financial cost to mitigate the public and environmental health risks. Lack of general knowledge of how to dispose of unused pharmaceuticals leads to improper disposal resulting in accidental toxicity, rising healthcare costs, landfills pilfering/scavenging, water supply pollution, anti-microbial resistance, and death. To mitigate such effects, pharmacists should raise public awareness about safe disposal practices. Objective: This review aims to examine the sources of pharmaceutical waste, disposal costs, secure disposal methods, the effects of inappropriate disposal, and the role of pharmacists in the disposal. Method: The information on the stated objectives was gathered from available sources through a comprehensive literature review. Conclusion: Many countries contain tons of pharmaceutical waste that are expensive to destroy. Because of improper disposal, pharmaceutical waste has been found at trace amounts in drinking and surface water. A practical, environmentally sustainable approach to pharmaceutical waste management, with policies and guidelines, and public awareness campaigns, are necessary to address the problem of safe waste disposal. The national drug regulatory bodies should conduct environmental risk assessment resulting from the disposal of unwanted pharmaceuticals. Pharmacists should facilitate extensive training on sustainable drug use and proper pharmaceutical waste disposal at all levels to reduce the risks associated with improper disposal. Reduction of pharmaceutical waste generation at each step of a drug’s lifecycle, implementing takeback options, collection at approved sites, and modern technology to treat wastewater are highly recommended to reduce the effects of unwanted pharmaceuticals on human health and the environment.

The cast grains of the 7055 aluminum alloy were refined by adding Sm + Er, and the proper heat treatment procedure was utilized to further precipitate the rare earth phase in order to increase the alloy's strength and toughness. The grain size, microstructure and phase were characterized by optical microscopes (OM), Scanning electron microscopy - energy spectrum (SEM-EDS), XRD diffractometer (XRD). The macroscopic hardness, yield strength and tensile strength of alloy materials were measured by hardness meter and universal electronic tensile machine. The results shown that the as-cast sample and the heat treatment sample all exist Al10Cu7Sm2 and Al8Cu4Er rare earth phase; But after heat treatment, the volume percentage of the rare earth phase dramatically increased and the dispersion was more unified. When 0.3wt.%Sm and 0.1wt.%Er were added, the grain size could be refined to 53μm. With the increase of the total content of rare earth elements, the refining effect first increased and then decreased. Under 410 oC solid solution for 2h + 150oC aging for 12h, the macroscopic hardness, yield strength, tensile strength and elongation of 0.3wt.%Sm + 0.1wt.%Er+7055 as-cast sample were 155.8HV, 620.5Mpa, 658.1Mpa, and 11.90%, respectively.

Solid waste management is challenging in many countries, especially developing economies. The impacts of the pandemic continue to be felt and have indicated secondary impacts on waste management. This work draws on data on household solid waste (HSW), healthcare waste (HCW), and recyclables collected in the Rio de Janeiro municipality, analyzed from January 2018 to December 2022. As expected, the collection of HCW in Rio de Janeiro municipality experienced a noticeable increase in 2020 and 2021, with an average of 46.9 tons and 54.3 tons collected, respectively. Notably, 2021 saw a significant 30% increase compared to 2019 (p-value<0.001). No significant difference was observed in recyclables collected from 2018 to 2021. The average recyclable amount was 3,638 and 3,747 tons per month in 2020 and 2021. In contrast, the monthly amount was equal to 4,819.5 tons in 2022, representing an increase higher than 32% compared to previous years (p-value<0.05). Our findings can be used to adapt and improve waste systems to cope with similar emergency scenarios in the future, serving as a template for municipalities with similar challenges.

: The paper presents the results of uniaxial tensile tests of samples of hypoeutectic aluminum-silicon alloy A319. According to the results of which the influence of surface treatment by a pulsed electron beam on the mechanical properties of the material was determined. The peculiarities of localization of deformation in the material, caused by grinding of the surface layer material structure due to rapid crystallization during electron beam treatment were revealed. The surface treatment up to 100 µm depth leads to the formation of a fine dendritic columnar structure of silumin and to an increase in the plasticity of the samples. The influence of surface treatment affects the increase of deformation localization in the region of stable concentrator before failure. The largest increase in ductility and localization of deformation occurs during processing with energy density of 15 J/cm2. In the process of specimen deformation, unstable, metastable, and stable areas of plastic deformation localization are formed and replaced, and the formation of stable areas of localized plastic deformation, in which the specimen fails at the end of the test, can be detected at the initial stages of testing. In specimens, during testing in the zone of localized plastic deformation, bands are formed that pass through the entire surface of the specimen at an angle from 35 to 55 degrees to the axis of tension, their evolution leads to the formation of stable zones of localized plastic deformation and to the failure of the specimen.

Aluminum profile surface defects can greatly affect the performance, safety and reliability of products. Traditional human-based visual inspection is low accuracy and time consuming, and machine vision-based methods depend on hand-crafted features which need to be carefully designed and lack robustness. To recognize the multiple types of defects with various size on aluminum profiles, a multiscale defect detection network based on deep learning is proposed. Then, the network is trained and evaluated using aluminum profile surface defects images. Results show 84.6%, 48.5%, 96.9%, 97.9%, 96.9%, 42.5%, 47.2%, 100%, 100%, 43.3% average precision(AP) for the ten defect categories, respectively, with a mean AP of 75.8%, which illustrate the effectiveness of the network in aluminum profile surface defects detection. In addition, saliency maps also show the feasibility of the proposed network.

Lightweight composite sandwich structures are laminated composite structures that are composed of thin stiff face sheets bonded to a thicker lightweight core in between. These structures have high potential to be used in marine, aerospace, defense and civil engineering applications due to their high strength to weight ratios and energy absorption capacity.In this study, composite sandwich structures were developed with carbon fiber reinforced polymer composite face sheets and aluminum honeycomb core materials with various thicknesses. Carbon fiber/epoxy composite face sheets were fabricated with lamination of [0/90]_s carbon fabrics by vacuum infusion technique. Al honeycomb layers were sandwiched together with the face sheets using a thermosetting adhesive. Mechanical tests were carried out to determine the mechanical behavior of face sheets, Al cores and the composite structure. Effect of core thickness on the mechanical properties of the sandwich was investigated.

This paper focuses on the highly radioactive, long-lasting nuclear waste produced by the currently operating fission reactors and on the way to deal with the sensitive issue of spent fuel reprocessing. The review includes a short description of the fission process and a detailed analysis of the more hazardous radioisotopes produced either by secondary reactions occurring in the nuclear installations or by decay of the fission fragments. Also outlined are the strategies presently adopted to minimize the harmfulness of the nuclear waste to be disposed and discussed advanced options and possible solutions proposed for the recycling of the used fuel and for the reusing of some technologicaly relevant radioisotopes.

There are four categories of medical waste that cannot be mixed as this will cause serious problems such as environmental pollution or infection. In the past, the classification of medical waste often involved a lot of human and material resources to process, with workers at risk of exposure to infectious substances. Therefore, an augmented reality (AR) and artificial intelligence (AI) medical waste classification system and method were developed. This innovative medical waste classification system and method combines AR and AI identification technology to reduce the risk of manual judgment errors by clinical staff when handling medical waste.

This study involved the fabrication of a set of Aluminum ion-grafted SBA-15 utilizing ethylene-diamine and trimethylamine ionic liquids. The primary objective was to examine the impact of the fabrication environment on the physicochemical characteristics of the catalysts. Comprehensive characterization of the Al-SBA-15 catalysts was conducted using various techniques, including XRD, FTIR, surface area, pyridine FTIR, 27Al-NMR, TGA, HRTEM, and FESEM, to analyze their physicochemical characteristics. Furthermore, the acidic characteristics were examined by con-ducting potentiometric titration in a nonaqueous solvent and employing FTIR spectroscopy to an-alyze the chemisorbed pyridine. The effectiveness of the fabricated acid materials was evaluated by testing their performance in the acetic acid esterification with butanol. The findings obtained reveal that the mesostructured of SBA-15 remains intact following the successful inclusion of Al3+ ions into the silica frameworks. Additionally, a remarkable enhancement in the existence of both Bronsted and Lewis acid centers is noted due to the grafting process of Al3+ ions. At temperatures of 80°C and 100°C, the reaction in Al-SBA-15(T-120) proceeds swiftly, reaching approximately 32% and 38% conversion, respectively, within a span of 110 minutes. The excellent catalytic performance observed in the esterification reaction can be attributed to two factors: the homogeneous distribution of Al3+ ions within the SBA-15 frameworks and the acidic character of Al-SBA-15. The findings further indicate that the grafting process for incorporating Al3+ ions into the silica matrix is more efficient.

The hot rolling in the process chain of the aluminium rolled products present the critical element of material quality and influence on productivity. The desire to increase the letter demand modifications of hot rolling, consequential changes of microstructure, crystallographic texture, mechanical and formability properties must be knowledge and consistently considered in planning the rolling process and rolled product. Achieving lower thicknesses of the hot-rolled band would enable fewer passes with cold rolling; consequently, hot rolling with the same number of passes will complete with lower temperatures. Microstructural and texture characterization with the optical microscope and scanning electron microscope for the hot-rolled band 3.25 mm the smaller grains appeared in the center of the cross-section, unlike for the hot-rolled band 6 mm, the smaller grains were detected on the upper and bottom position of the cross-section. Furthermore, the comparison shows also that the hot-rolled band 6 mm has 64 % of random texture components and 83 % of recrystallized grains, and the proportional adjustment for the hot-rolled band 3.25 mm has the 42 % of random texture components and 55 % of recrystallized grains. For the mechanical testing results, the elongation values in rolling and transverse directions significantly differ just in the case of a hot rolled band of 3.25 mm. Consequently, the earing results are more than 1.5 % higher for the hot-rolled band, 3.25 mm, than the hot-rolled band, 6 mm.

Electrochemical deposition of silicon at room temperature is problematic due to intrinsically low conductivity of the deposits. This study reports the photoelectrochemical (PEC) deposition of silicon (Si) and silicon–carbon (Si–C) layers from an ionic liquid at temperature 40 oC using silicon tetrachloride (SiCl4) as a silicon precursor. Amorphous layers are deposited on p-type silicon (p-Si), p-type gallium arsenide (p-GaAs), and aluminum–copper alloy AA2024. The semi-conductor substrates are activated by white LED illumination, which generated photoelectrons, thereby making the substrate conductive with respect to the cathodic reaction. Photoresponsive-ness of the deposits is proven by the light-induced photocurrents on an optically inactive substrate made of the alloy AA 2024. The proposed method paves the way for the electrochemical modifica-tion of semiconductors and metals with Si and Si–C structures, which are applicable in various fields, such as; batteries, anti-corrosion coatings, photovoltaics, or PEC electrodes for hydrogen production.

The present work aims to explain the aluminum hydrolysis reaction kinetics based on properly chosen theoretical model with machined aluminum waste chips and alkali solutions up to 1M as a promoter, and to estimate overall reaction profit. In order to obtain results of better accuracy, we work with flat Al waste chips because a flat surface is preferable to maximally increase the time for created hydrogen bubbles to reach the critical gas pressure. At describing the reaction kinetics, flat shape allows using a planar one-dimensional shrinking core model instead of much complicated polydisperse spheric shrinking core model. We analyze the surface chemical reaction and mass transfer rate steps to obtain the first order rate constant for surface reaction and the diffusion coefficient of aqueous reactant in the byproduct layer, respectively. With our reactor we achieved H2 yield of 1145 mL per 1 g Al with 1M NaOH, which is 92% of the theoretical maximum. At estimation of the profit, we pay much attention to the loss of alkaline and find a crucial dependence on its price. Nevertheless, in terms of consumed and originated materials for sale, conversion of the aluminum waste material into green hydrogen by properly chosen reaction parameters has a positive profit even by consuming alkali of chemical grade.

In this paper, 6063 aluminum alloy for common building profiles is used as the research object. By adding a new Al-Ti-C-La composite alloy, the effect of 6063 aluminum alloy on the microstructure and properties of 6063 aluminum alloy is studied. The results show that Al-Ti-C-La composite alloy has obvious effect on grain refinement of 6063 aluminum alloy. With the addition of Al-Ti-C-La composite alloy, the grain size decreased significantly. When the addition amount of Al-Ti-C-La composite alloy is 1%, the grain size is reduced from 482 μm to 121 μm. Rare earth La is mainly distributed near the Mg2Si phase and β-AlFeSi, and complex compounds such as AlFeSiMgLa are formed. After aging for 270 days on the basis of T6 heat treatment, the tensile strength and elongation of 6063 aluminum alloy augmented with the addition of Al-Ti-C-La composite alloy, and the Vickers hardness gradually diminished. When the addition amount of Al-Ti-C-La composite alloy is 1%, the tensile strength, elongation and Vickers hardness of 6063 aluminum alloy reach 177.2 MPa, 17.8% and 60.9 HV, respectively, and the tensile strength is increased by 16.3%. The elongation is increased by 50.8%, the Vickers hardness is reduced by 15.4%, and the fracture of the alloy is mainly ductile fracture.

The electrical and optical properties of sol-gel derived aluminum-doped0 zinc oxide thin films containing 2 at.% Al were investigated considering the modifying effects of 1) increasing the sol H₂O content; and 2) thermal treatment procedure with high-temperature approach followed by an additional heat-treatment step under a reducing atmosphere. According to the results obtained via the TG-DTA analysis, FT-IR spectroscopy, X-ray diffraction technique and four-point probe resistivity measurement, it is argued that the sol hydrolysis, decomposition of the deposited gel and crystallization of grains result in grains of larger crystallite size and stronger c-axis preferred orientation with slightly less microstrain in the modified sample. The consequent morphology and grain-boundary characteristics turn out as improved conductivity, implying higher values of concentration and mobility of charge carriers. A detailed investigation on samples optical properties, in terms of analyzing their absorption and dispersion behaviors through the UV-Vis-NIR spectroscopy, support our reasoning for the increase of the mobility, and to a lesser extent, the concentration of charge carriers, while causing only a slight degradation of optical transmission. Hence, an enhanced performance as a transparent conducting film is claimed for the modified sample by comparing the figure-of-merit values.

Surface damage on honeycomb aircraft panels is often measured manually, and is therefore subject to variation based on inspection personnel. Eddy current testing (ECT) is sensitive to variations in probe-to-specimen spacing, or lift-off, and is thus promising for high resolution profiling of surface damage on aluminum panels. Lower frequency testing also allows inspection through the face sheet, an advantage over optical 3D scanning methods. This paper presents results from the ECT inspection of surface damage on an approximately flat aluminum honeycomb aircraft panel, and compares the measurements to those taken using optical 3D scanning technology. An ECT C-Scan of the dented panel surface was obtained by attaching the probe to a robotic scanning apparatus. Data was taken simultaneously at four frequencies of 25, 100, 400 and 1,600 kHz. A reference surface was then defined that approximated the original, undamaged panel surface, which also compensated for the effects of specimen tilt and thermal drift within the ECT instrument. Data was converted to lift-off using height calibration curves developed for each probe frequency. A damage region of 22,550 mm² area with dents ranging in depth from 0.13-1.01 mm was analyzed. The method was accurate at 1,600 kHz to within 0.05 mm (2s) when compared with 231 measurements taken via optical 3D scanning. Testing at 25 kHz revealed a 3.2 mm cell size within the honeycomb core, which was confirmed via destructive evaluation. As a result, ECT demonstrates potential for implementation as a method for rapid in-field aircraft panel surface damage assessment.

Starting from an original survey conducted in eight countries in 2021 (Canada, China, Germany, Italy, Russia, Spain, UK, and USA), this research explores the relationship between household food waste and dietary habits in a cross-country comparative perspective. 8,000 questionnaires were recorded from samples representative of adult population of each country through an online survey conducted between the 13th and the 24th of August. The questionnaires were built on the work of Waste Watcher International Observatory on Food and Sustainability, an international observatory of social, behavioral and lifestyles dynamics behind household food waste. Relationship between per capita self-reported amount of food waste (expressed in kilocalories) and self-declared dietary habits (Traditional, Healthy and Sustainable, Vegetarian, Smart, Confused) was estimated using multiple linear regression models. Results show that Smart diets are associated with higher values of food waste in Canada, Spain, UK and USA. Vegetarian diets are associated to lower food waste values in China, Germany, UK and USA but not in Italy, Russia and Spain. Since the share of population adopting a Smart diet is on average 2.7% of the sample, interventions for food waste reduction should focus on this specific type of consumers, often associated to larger amounts of food waste.