Silver powder, as the primary component of solar silver paste, significantly influences various aspects of paste performance, including printing, sintering, and conductivity. Silver powders prepared using the liquid-phase reduction method exhibit different microstructures depending on whether the growth process is dominated by aggregation or crystalline growth. This study explores the impact of different silver powder microstructures on packing density and sintering activity. It is observed that polycrystalline aggregated silver powder possesses higher surface energy, lower packing density, and greater sintering activity. Investigation into the influence of different silver powders on the electrical conductivity, adhesion, and structural density of silver paste reveals that polycrystalline aggregated silver powder is more suitable for lower sintering temperature pastes, whereas crystalline growth-type silver powder is better suited for higher sintering temperature pastes, resulting in a denser sintered silver layer. Finally, an analysis of the impact of various silver powders on the aspect ratio and electrical performance of solar cell silver grid lines yields higher aspect ratios (0.40) and photoelectric conversion efficiency (19.26%).

Iron powders having average particle sizes of ~40µm are mechanically mixed thoroughly with aluminum powders ranging from 1 to 10 in wt.% with an average particle size of ~10µm. Two different powder metallurgical techniques cold and hot pressing are used to study the effect of the additive element powder on the mechanical properties, wear properties and the microstructure of the iron based alloys. The hot pressing technique was performed at a temperature up to 500°C at 445.6 MPa. The cold pressing technique was performed at 909 MPa in room temperature. By increasing the Al content to 10 wt. % in the base Fe-based matrix, the hardness was decreased from 780 to 690 MPa and the radial strength was decreased from 380 to 202 MPa with reductions of 11.5% and 40%, respectively. Improvement of the wear resistance with the increase addition of the Al powder to the Fe matrix up to 5 times was achieved compared to the alloy without Al addition for different wear parameters namely; wear time and sliding speed.

As a new type of high-performance material, gradient structural steel is widely used in engineering fields due to its unique microstructure and excellent mechanical properties. For the prevalent fatigue failure problem, the rate of change of the local grain size gradients along the structure (referred to as the gradient rate) is a key parameter in the design of gradient structures, which significantly affects the fatigue performance of gradient structural steel. In this work, a method of ‘Voronoi primary + secondary modeling’ is adopted to successfully establish three typical high-strength steel models corresponding to the convex, linear, and concave type gradient rates for gradient structures, focusing on the stress-strain response and crack propagation in structural steel with different gradient rates under cyclic loading. It is found that the concave gradient rate structural model is dominated by finer grains with larger volume fraction, which is conducive to hindering fatigue crack propagation and has the longest fatigue life; the linear structure is the second one, and the convex structure is the shortest one. The simulation results in this work are consistent with the relevant experimental phenomena. Therefore, when regulating the gradient rate, priority should be given to increasing the volume fraction of fine grains and designing a gradient rate structure dominated by fine grains to improve the fatigue life of the material.

Swarf of aluminum alloy with high corrosion resistance and ductility was successfully converted into fine hydroreactive powders via its ball milling with silver powder and either lithium chloride or gallium. The later substances significantly intensified particle size reduction, while silver formed ‘cathodic’ sites (Ag, Ag2Al) promoting Al corrosion in aqueous saline solutions with hydrogen generation. The diffraction patterns, microphotographs, and elemental analysis results demonstrated partial aluminum oxidation in the samples and their contamination with tungsten carbide from milling balls. Those effects were responsible for obtaining hydrogen yields lower than expected. For AlCl3 solution at 60 °C, Al–LiCl–Ag, Al–LiCl, Al–Ga–Ag, and Al–Ga composites delivered (84.6±0.2), (86.8±1.4), (80.2±0.5), and (76.7±0.7)% of the expected hydrogen respectively. Modification with Ag promoted Al oxidation thus providing higher hydrogen evolution rates. The samples with Ag were tested in CaCl2 solution as well, for which the reaction proceeded much slower. At a higher temperature (80 °C) after 3 h of experiment, the hydrogen yields for Al–LiCl–Ag and Al–Ga–Ag powders were (46.7±2.1) and (31.8±1.9)%. The tested Ag-modified composite powders were considered promising for hydrogen generation and had a potential for further improvement to provide higher performance.

AgW materials exhibit excellent properties and are widely used as contact materials in low- and medium-voltage switches. In this study, a pre-sintering and infiltration method was employed to pre-sinter W powder with Cu, Ni, and (Cu+Ni) addition in the low temperature range of 950–1050 °C. The low-temperature sintering behaviours of W skeletons with different additives were investigated. Subsequently, AgW70, AgW75, AgW80, and AgW85 materials were prepared through infiltration at 1050 °C. The microstructure morphology and physical properties of high-W contact materials were investigated using a metallographic microscope and scanning electron microscope. The mechanism of low-temperature sintering-infiltration of high-W contact materials was elucidated. The results indicated that pure W and 1% Cu-added W skeletons experience minimal linear shrinkage within the temperature range of 950–1050 °C. The linear shrinkage curves of W skeletons with different additives coincided under the conditions of 950–1000 °C/90 min. At 1050 °C, after sintering for 150 min, the particle boundaries in the W skeleton were fully spheroidised, with a dihedral angle of 120°. At 1050 °C and after 150 min of infiltration, cross-sectional micrographs of the AgW material revealed the presence of irregular Ni layers, where Ni spatially enveloped/encapsulated Ag. With an increase in the W content, the electrical conductivity and relative density of AgW(70–85) materials decreased, whereas the hardness of the materials increased.

The endocannabinoid system has been found to be pervasive in mammalian species. It has also been described in invertebrate species primitive as the Hydra. Insects apparently are devoid of this otherwise ubiquitous system that provides homeostatic balance to the nervous and immune systems, as well as many other organ systems. The endocannabinoid system (ECS) has been defined to consist of three parts: 1. Endogenous ligands, 2. G-protein coupled receptors (GPCRs), and 3. Enzymes to degrade and recycle the ligands. Two endogenous molecules have been identified as ligands in the ECS to date. These are the endocannabinoids: Anandamide (arachidonoyl ethanolamide) and 2-AG (2-arachidonoyl glycerol). Two G-coupled protein receptors have been described as part of this system, with other putative GPC being considered. Coincidentally, the phytochemicals produced in large quantities by the Cannabis sativa L plant, and in lesser amounts by other plants, can interact with this system as ligands. These plant-based cannabinoids are termed, phytocannabinoids. The precise determination of the distribution of cannabinoid receptors in animal species is an ongoing project, with the canine cannabinoid receptor distribution currently receiving the most interest in non-human animals.

A long-standing problem in the understanding of deep-water turbidite reservoirs relates to how the three-dimensional evolution of deep-water channel systems evolve in response to channel filling on spatio-temporal scales, and how depositional environments affect channel architecture. The 3-D structure and temporal evolution of late Miocene deep-water channel complexes in the southern Taranaki Basin, New Zealand is investigated, and the geometry, distribution and stacking patterns of the channel complexes are analyzed. Two recently acquired 3-D seismic datasets, the Pipeline-3D (proximal) and Hector-3D (distal) are analyzed. These surveys provide detailed imaging of late Miocene deep-water channel systems, allowing for the assessment of the intricate geometry and seismic geomorphology of the systems. Seismic attributes resolve the channel bodies and the associated architectural elements. Spectral decomposition, amplitude curvature, and coherence attributes reveal NW-trending straight to low-sinuosity channels and less prominent NE-trending high-sinuosity feeder channels. Stratal slices across the seismic datasets better characterize the architectural elements. The mapped turbidite systems transition from low-sinuosity to meandering high-sinuosity patterns, likely caused by a change in the shelf-slope gradient due to localized structural relief. Stacking facies patterns within the channel systems reveal the temporal variation from a depositional environment characterized by sediment bypass to vertically aggrading channel systems.

In this paper we report a new development on the numerical model for aluminum-steam combustion. This model is based on diffusion flame of continuum regime and the thermal equilibrium between the particle and the flow field, which can be used to calculate the aluminum particle combustion model for two phase calculation conditions. The model prediction is in good agreement with the experimental data. A new type of vortex combustor was proposed for the combustion of aluminum and steam, and the mathematical model of the two phase reacting flow with in this combustor was established. The turbulence effects are modeled using the Reynolds Stress Model (RSM) with Linear Pressure-Strain approach, and the Eddy-Dissipation model is used to simulate the gas phase combustion. Aluminum particles are injected into the vortex combustor and form a swirling flow around the chamber and their trajectories are traced using the Discrete Phase Model (DPM). The simulation results show that the vortex combustor can achieve high efficient combustion of aluminum and steam. The influencing factors, such as the eccentric distance of the inlet of aluminum particles, particle size and steam inlet diameter, etc., are studied. The work described in this paper represents an attempt to the design of a vortex combustor in order to increase aluminum combustion efficiency.

A method for accurately determining the chemical composition of deposits at the bottom of pores during the electrocoloring (e-coloring) of aluminum anodic oxide (AAO) layers in tin-based solutions is developed. The aluminum samples were AC e-colored after DC sulfuric anodization. Free-standing, tin e-colored aluminum oxide film was obtained by selective dissolution of the metallic aluminum from the AAO in copper chloride solution to access the deposit directly at the bottom of the pore. This allowed us to take XPS analysis directly from the deposits at pore bottoms without any interference from the base material or insulating barrier layer. The results revealed the presence of a mixture of tin oxide and metal in the deposits, which were richer in oxide content. Furthermore, a cyclic voltammetry experiment mimicking real polarization conditions during AC conditions was optimized and used to gain a deeper understanding of the electrochemical reactions that occur during AC electrocoloring. The comparison of CV results in tin-free and tin-containing electrolytes indicated that the tin deposited during a cathodic cycle is oxidized in the anodic cycle. The formation of tin based deposits radically changed the CV behavior. The XPS and cyclic voltammetry results consistently show that the deposits formed during e-coloring comprised a mixture of metallic and oxidic tin species richer in oxide content.

Green synthesis of silver nanoparticles (AgNPs) using raw Whey has never been reported. Silver nanoparticle formation involves a reduction reaction of silver salt solution with Whey extract. Extract and metal salt concentrations, and temperature can control this reaction. In this work, incubation period, extract, AgNO3, and NaOH concentrations were used as the independent factors using central composite design under response surface methodology. The aim was to elucidate the influence these factors have on the measured UV-Vis absorption spectra fitted with a Voigt function, and to optimize the conditions for nanoparticle formation. The fitting parameters, peak wavelength (λ0), peak area (A), and Full Width at Half Maximum (FWHM), were the responses. Silver nanoparticle formation was only possible in an alkaline environment (pH 10). The peak wavelength and the FWHM are influenced mainly by extract and AgNO3 concentrations. In contrast, the peak area is influenced by a total of 33.54 % from the interaction terms of AgNO3 and extract concentrations with NaOH. Metallic AgNPs were formed for the following parameter ranges: a) Whey (0.4 – 1.6 % v/v), b) AgNO3 (0.15 – 0.6 mM), c) NaOH (10 – 50 mM), and d) Time (20 – 60 min). Silver oxide nanoparticles were also observed.

While L-PBF offers advantages in terms of geometrical freedom or lightweight construction, its use is often limited by economic constraints or currently achievable part costs. With an anticipated increase of L-PBF machine productivity during the next years, an increase of the share of material costs and the share of non-productive time for powder layer application process is to be expected. This results in a demand for less expensive powder materials and advanced processing strategies for the short-and medium-term advancement of L-PBF. As one possible approach, the processing of gas- and water atomized stainless steel (316L) powders with different morphology and particle size distribution as well as their impact on L-PBF productivity is investigated. The actual powder applicability in L-PBF systems and the L-PBF processability determines the minimum necessary powder quality. The main focus of the presented work is put on the interaction between powder quality, powder layer properties, part quality and cost-effectiveness of the L-PBF process. To this end, the influence of the gas and water-atomized powder properties (particle size and morphology) during the powder layer application process at highest possible powder recoater speeds and the resulting powder bed properties (powder layer density, powder bed density, powder demixing) and part properties (part density and tensile strength) is investigated.

One of the relevant goals in forging technologies is simplifying the existing process and developing new processes that can retain the original or very close to the original dimensions and billet shape after the end of the deformation cycle. This study attempts to develop a forging equipment design that provides alternating cyclic loading; the alternate cyclic forging (ACF) method is proposed. To preliminary evaluate the ACF and study the plastic deformation behavior, numerical simulation via finite element modeling (FEM) was conducted using DEFORM-3D. The main attention was paid to the metal flow characteristics, effective strain and stress distribution, and the forging load. The ACF results in non-uniform metal flow with the formation of diagonal and vortex flows were demonstrated. Maximum effective strains and stresses zones are localized at two points of the billet contact with the surface of the tooling container and at two points of the interface between the punches. It was also assumed that reducing the contact area between the punch and the billet using separate semi-cylindrical punches can reduce the forging load. Preliminary finite element analysis (FEA) results of the proposed process after four successive steps of the deformation cycle confirmed the feasibility of its general implementation.

Effects of oxygen content on microstructure and creep property of FGH96 superalloy were investigated. When oxygen content increased from 135ppm to 341ppm, prior particle boundary (PPB) rose from degree 2 to degree 3, and the size of γ′ phase on PPB enlarged from 1.07μm to 1.27μm, and MC carbide size grew from 77.4nm to 104.0nm. Meanwhile, the steady creep rate accelerated form 4.34×10-3 h-1 to 1.87×10-2 h-1, and the creep rupture life shortened from 176h to 94h, and the creep rupture mode transferred from intergranular and transgranular mixed fracture to along PPB fracture. During creep, the micro-twins formation and gliding will be restrained by ∑3 boundaries. FGH96 superalloy with higher oxygen content contains less ∑3 boundaries and its micro-twins cross slipped instead of single direction slip in lower oxygen content superalloy. Consequently, specimen with higher oxygen content creeped faster and raptured earlier.

In order to enhance the efficiency and combined performances of nitriding layer, aluminum-modified plasma nitriding (Al-PN) was developed in this research by adding some FeAl particles around the samples during plasma nitriding (PN) for 42CrMo steel. The results show that the efficiency is dramatically enhanced almost 6 times comparing with traditional PN, with the effective hardening layer increasing from 224 μm to 1246 μm at 520℃/4h. More importantly, the compound layer increased just a little bit from 11.64 μm to 14.32 μm, which remarkably reduces the ratio of the compound layer thickness to effective hardening layer thickness, thus being quite beneficial to decrease the brittleness level, making the brittleness level decreasing from Level 4 to Level 1. Meanwhile, ultra-high surface hardness and excellent wear behaviors are obtained by aluminum-modified plasma nitriding (Al-PN) due to the formation of dispersed strengthening phased of AlN and FexAl in the nitriding layer, with the surface hardness increasing from 755 HV0.025 to 1251 HV0.025, wear rate decreasing from 8.15 x10-5g N-1 m-1 to 4.07 x10-5g N-1 m-1. In other words, comparing with PN, the wear resistance has been almost doubled by Al-PN. Therefore, the research can provide comprehensive insights into the surface characteristics and combined performances of the aluminum-modified plasma nitriding layer.

7046 aluminum alloy has good fatigue property, corrosion resistance and weld property, but the moderate strength and plasticity limit its wider application and development. In the present study, severe plastic deformation (SPD) was applied prior to T6 treatment to significantly strengthen and toughen the 7046 aluminum alloy. Results indicate that the alloy processed by 4 passes of equal channel angular pressing (ECAP) at 300 ℃ prior to T6 treatment exhibits an excellent mechanical performance, with ultimate tensile strength (UTS) and elongation (EL) of 485 MPa and 19%, exhibiting an improvement of 18.6% and 375% compared to that of the T6 alloy, respectively. The mechanical properties of the alloy are further improved by the additional room temperature (RT) rolling process, with UTS of 508 MPa and EL of 23.4%. There are more precipitates of η' and Al6Mn phases in the 300℃4P-R80%-T6 and 300°C4P-T6 alloys, which contribute to the strengthening and toughening enhancement by SPD processed T6 alloy. The results of this work may shed some light on enhancing 7046 aluminum alloy.

Laser-Powder Directed Energy Deposition (DED-LB/Powder) is an additive manufacturing process that is gaining popularity in the manufacturing industry due to its numerous advantages, particularly in repairing operations. However, its application is often limited to case studies due to some critical issues that need to be addressed, such as the degree of internal porosity. This paper investigates the effect of the most relevant process parameters of the DED-LB/Powder process on the level and distribution of porosity. Results indicate that, among the process parameters examined, porosity is less affected by travel speed and more influenced by powder mass flow rate and laser power. Additionally, a three-dimensional finite element transient model was introduced, which was able to predict the development and location of lack-of-fusion pores along the building direction.

The study findings revealed significant variability in various wood properties among different genetic families, although the static modulus of elasticity did not exhibit significant differences between the chosen genetic families. All measured wood properties decreased from the bottom to the top of the model trees. Wood hardness displayed a moderately negative correlation with wood density and weak correlations with MOE and MOR. Given the weak correlations between wood hardness and other wood mechanical properties, it is suggested that the MOEdyn would be a more suitable trait for genetic studies.

This study investigated the relationship between aluminum adjuvant vaccines and the prevalence of 4 childhood diseases (Autism, Allergies, Asthma, ADD/ADHD) using data from the 2020-2021 National Survey of Children's Health (NSCH) [1] and the Centers for Disease Control National Immunization Survey (CDC NIS) [2]. The study found an association with aluminum adjuvant dosage and the prevalence of each disease studied (Autism, Allergies, Asthma, ADD/ADHD) through a weighted regression analysis of disease prevalence against the summed likelihood of aluminum adjuvant vaccine uptake.

This study utilises NaOH to treat composite cementitious materials containing aeolian sand and zeolite powders, which were used to replace 50% of the cement in aeolian-sand concrete (ASC). The mechanical properties of treated ASC considerably improved, especially when the NaOH dosage was 4% by mass. After curing this sample (denoted as AAZC-4) for 28 d, its compressive strength improved by 17.2% and its split tensile was increased by 16.3%. Potassium feldspar and montmorillonite in zeolite powder and SiO2 in the sand were decomposed by OH− and combined with other elements to generate various silicate gels and A-type potassium zeolite crystals inside the concrete. Microscopic examination showed that the gels and crystals intertwined to fill the pores, decreasing (increasing) the percentage of large (small) pores, thus optimising the pore structure. This substantially improved the mechanical properties of ASC. Freeze–thaw salt-intrusion tests showed that the extent of mass loss, degree of damage and loss of compressive strength of AAZC-4 were similar to those of ordinary concrete but were reduced by 36.8%, 19% and 52.1%, respectively, compared with those of ASC. Therefore, AAZC-4 has sustainable working performance in the chloride ion permeable environment in cold and arid areas.

Infrastructure development is rapidly increasing, driving up demand for concrete, a key construction material. Cement and aggregate are essential constituents, with global cement production reaching 4.1 billion metric tons in 2011 and CO2 emissions hitting 1.7 billion metric tons by 2024, a significant contributor to carbon emissions. To address this, alternative constituents like Rice Husk Ash (RHA) and Animal Bone Powder (ABP) are proposed. With rice husk comprising 20% of rice weight and a substantial cattle population in Bangladesh, RHA and ABP offer promising alternatives. This study examines the benefits and limitations of incorporating RHA and ABP into cement, focusing on concrete strength and permeability. By replacing varying percentages of cement with RHA and ABP simultaneously, experiments evaluate their impact on concrete properties after 28 days of curing. The research aims to identify the optimal combination for sustainable concrete production, reducing environmental impact by curbing waste generation and pollution. Results show that compressive strength increases and permeability decreases with up to 5% replacement of RHA and ABP, highlighting their potential for enhancing concrete performance while mitigating environmental concerns.

: The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDX, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a TPD CO2 measurement. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.78; 2.24 and 1.26 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

To be CMOS-compatible, a low preparation temperature (< 500 °C) of ferroelectric films is required. In this study, BiFeO3 films were successfully fabricated at a low annealing temperature (< 450 °C) on aluminum foils by a metal-organic decomposition process. The annealing atmosphere on performance of BiFeO3 films was assessed at 440 ± 5℃. By replacing an O2-rich atmosphere with an N2-rich one, a better crystalline morphology was achieved in BiFeO3 films, resulting in better electric properties targeted for high-density ferroelectric random-access memory applications. These properties included a large remnant polarization (Pr~78.1 μC/cm2 @ 1165.2 kV/cm) and a high rectangularity (~91.3% @ 1165.2 kV/cm) of the P-E loop, along with excellent charge-retaining ability up to 1.0 × 103 s and a fatigue resistance reaching 1.0 × 109 switching cycles. The enhanced performance of BiFeO3 film in an N2-rich atmosphere maybe originated from the slightly high content of oxygen vacancies during the annealing process. Furthermore, decent electrical properties (Pr~70 μC/cm2 @ 1118.1 kV/cm) of the BiFeO3 films were achieved at a very low annealing temperature of 365 ±5 °C on aluminum foil substrates. These results offer a new idea for lowering the annealing temperature for integrated ferroelectrics in high-density FeRAM applications.

Objective: To compare the overall survival (OS) and surgical outcomes between open and minimally invasive surgery (MIS) in a large cohort of women with Type II endometrial cancer. Methods: Using the National Cancer Database, we identified a cohort of women who underwent hysterectomy for type II endometrial cancer (serous, clear cell, carcinosarcoma) between January 2010 and December 2014. Primary outcome was the comparison of OS between MIS and the open approach. Secondary outcomes included the length of hospital stay, readmission rate, 30- and 90-day mortality. Multivariable logistic regression and inverse propensity weighting analyses were performed. Results: A total of 12,905 patients with Type II, Stage I-III endometrial cancer who underwent hysterectomy were identified. Among these patients, 7,123 (55.2%) underwent MIS. The utilization of MIS increased from 39% to 64% over the four-year period. In propensity-score-weighted analysis, MIS was associated with superior OS (101.7 vs. 86.7 months, p=0.0003 by the log-rank test), with a hazard ratio of 0.9 (CI 0.857-0.954, p=0.0002). MIS was also associated with improved perioperative outcomes, including a shorter length of stay (1 vs. 4 days, p<0.001), lower 30-day readmission rate (2.5% vs. 5%), and lower 30- and 90-day postoperative mortality (0.5% vs. 1.3% and 1.5% vs. 3.6%, respectively; p<0.001). The time interval between surgery and initiation of chemotherapy was shorter in the MIS group (38 vs. 41 days, p<0.001).The increase in MIS adoption correlated with a decrease in 90-day postoperative mortality (2.8% to 2.2%, r=-0.89; p=0.003) and 12-month overall mortality (51% to 38%, r=-0.95, p=0.006). Conclusions: In an epidemiologic study, MIS is associated with improved overall survival and superior perioperative outcomes compared to open surgery in women with Type II endometrial cancer.

The activated carbons (ACs) derived from okara powder waste with high surface areas were modified with ammonia aqueous solution impregnation in an autoclave to enhance their CO2 adsorption properties toward CO2. The impregnated ACs were characterized in which surface chemical composition and properties of the ACs were analyzed by SEM-EDS, FTIR. Activated carbons were functionalized with ammonia aqueous solution (25%) through a hydrothermal process within 24; 48, and 72 hours. The adsorption performance of CO2 onto carbon samples was experimentally evaluated through a breakthrough adsorption experimental setup at room temperature. FTIR spectra confirm the N-containing in N-modified activated carbons and the presence of the –C = O stretch and N-H groups. CO2 uptakes of N-modified activated carbons are 0.24; 1.47; and 1.20 mmol/g, which are relatively comparable with those of activated carbons studied in in the literature.

Early detection of neurological conditions is critical for timely diagnosis and treatment. Identifying cellular-level changes is essential for implementing therapeutic interventions prior to symptomatic disease onset. However, monitoring brain tissue directly through biopsies is invasive and high-risk. Bodily fluids such as blood or cerebrospinal fluid contain information in many forms, including proteins and nucleic acids. Particularly, cell-free DNA (cfDNA) has potential as a versatile neurological biomarker. Yet, our knowledge of cfDNA released by brain tissue and how cfDNA changes in response to deleterious events within the brain is incomplete. Mapping changes in cfDNA to specific cellular events is difficult in vivo, where many tissues contribute to circulating cfDNA. Organoids are tractable systems for examining specific changes consistently in a human background. However, few studies have investigated cfDNA released from organoids. Here, we examined cfDNA isolated from cerebral organoids. We found that cerebral organoids release quantities of cfDNA sufficient for downstream analysis with droplet-digital PCR and whole-genome sequencing. Further, gene ontology analysis of genes aligning with sequenced cfDNA fragments revealed association with terms related to neurodevelopment and autism spectrum disorder. We conclude that cerebral organoids hold promise as tools for the discovery of cfDNA biomarkers related to neurodevelopmental and neurological disorders.

In this work, silver nanoparticles (AgNPs) were synthesized rapidly and eco-friendlily using the extract of Mulberry leaves and aqueous solution of silver nitrate without any toxic chemical [1,2]. The Mulberry leaves extract acts as both reducing agent and stabilizing agent. The UV-Vis spectrum shows peak at 430 nm. The TEM image of synthesized AgNPs sample shows spherical shaped particles whose size range from 15 to 20 nm. TEM image of nano silver solution sample synthesized by microwave assisted method shows nearly spherical particles with an average particle size of 10 nm. The absorption UV-vis spectrum of silver nanoparticles synthesized by microwave assisted method (AgNPsmw) shows a sharp absorption band around 415 nm. After two month storage of AgNPsmw, the absorption spectrum of AgNPsmw was taken again. The UV-Vis spectrum shows negligible peak changes of silver nanoparticles have occurred after two months of storage. The synthesized AgNPs material could be used as an antimicrobial, used in the field of textile and in wastewater treatment.

Polymeric composites such as Poly-ether-ether-ketone (PEEK)/carbon fiber (CF) have been widely utilized due to outstanding performances such as high specific strength and specific modulus. The PEEK/CF components via powder-bed fusion additive manufacturing usually show brittle fracture behaviors induced by their poor interfacial affinity and inner voids. These defects are strongly associated with powder packing quality upon deposition. The particle dynamic model has been widely employed to study the interactions of particle motions. Powder property, bulk material property, and interfacial features of composite powders are key factors in the particle dynamic model. In this work, an efficient and systematic material evaluation is developed for composite powders to investigate their deposition mechanism. The discrete element method is utilized to simulate the dynamic behaviors of PEEK/CF composite powders. The powder properties, bulk material properties, and interfacial features of powders are calibrated and justified by experimental measurement, numerical simulation, and design of experiments. The particle dynamic model can well explain the powder flow behaviors and interactions. It reveals that the addition of short CF particles can assist the flow of PEEK powders and improve the packing quality of the composite powders.

Titanium-based metal-matrix composites manufactured by additive manufacturing offer tremendous lightweighting opportunities. However, processing high reinforcement content remains challenging. This study reports an improved manufacturing process for Ti-TiC enabling high reinforcement content and significant fracture strain concurrently: mechanical blending, followed by laser powder bed fusion and a single heat treatment. As-built microstructure shows both un-melted TiC particles and sub-stoichiometric TiC dendrites resulting from a partial dissolution of TiC particles. The heat treatment is shown to fully convert TiC dendrites into equiaxed TiC grains. Reduction of the C/Ti ratio in TiC during the process results in an increase in the reinforcement content, from a nominal 12 vol% to an effective 21.5 vol%. Ti-TiC tensile samples reached fracture strains of up to 1.7%, Young’s moduli of up to 149 GPa and ultimate tensile strengths of up to 827 MPa. Lower TiC initial powder size distributions displayed the best mechanical performance.

Fused deposition modeling (FDM) is a rather new technology in the production of personalized dosage forms. Melting and printing of polymer–active pharmaceutical ingredient (API) – mixtures can be used to produce oral dosage forms with different dosage as well as release behavior. This process is utilized to increase the bioavailability of pharmaceutically relevant active ingredients that are poorly soluble in physiological medium by transforming them into solid amorphous dispersions (ASD). Release from such ASDs is expected to be faster and higher compared to the raw materials and thus enhance bioavailability. Printing directly from powder while forming ASDs was realized. Different techniques to change release patterns as well as a non-destructive way for determination of API distribution were shown. By measuring the melt viscosities of mixtures printed a rheological model for the printer used is proposed.

Recent studies have suggested significant antimicrobial properties of some metallic nanoparticles during the height of antibiotic resistance. The silver nanoparticle (AgNPs) is one of the most prominent candidates due to its noble nature and better tolerance profile in humans. The synthesis of AgNPs was carried out using silver nitrate using five different chemical reduction methods and comparing their activity with silver nitrate, also known to possess antimicrobial properties. AgNPs have been synthesized with varying combination of reducing agents, and subsequently characterized by UV-visible spectroscopy, thermogravimetric analysis (TGA), scanning electron microscopy (SEM), and dynamic light scattering (DLS). Chemical reduction with both trisodium citrate and sodium borohydride provided better particle size and controlled uniformity, whereas hydrogen peroxide was used as a stabilizer to increase the stability of AgNPs. The minimum bactericidal concentration (MBC) for all AgNP formulations was determined against gram-negative E. coli, and AgNPs synthesized with only trisodium citrate were found to be the most effective. The synthesized AgNPs were tested against the resistant strains of E. coli, Salmonella, Klebsiella, Bacillus, and Staphylococcus by the well diffusion method to evaluate and compare their inhibition zones and AgNPs synthesized with polyethylene glycol and polyvinyl pyrrolidine were found to be the most efficient.

Isothermal interrupted hot compression tests of 5754 aluminum were conducted on Gleeble-3500 thermo-mechanical simulator at temperature 350 °C and 450 °C, strain rate 0.1 s-1 and 1s−1. These tests simulated flat rolling to investigate how softening behaviors respond to controlled parameters, such as deformation temperature, strain rate and delay times. This data allowed the parameters for the hot rolling process to be optimized. The delay times during interrupted compression vary between 5s and 60s. The dynamic softening at each pass and metadynamic recrystallization at the intervals of deformation passes were analyzed in detail. 0.2% offset yield strength is applied to calculate the softening fraction undergoing metadynamic recrystallization. A kinetic model was developed to describe metadynamic recrystallization behaviors of the hot deformed 5754 aluminum alloy. Furthermore, the time constant for 50% recrystallization was expressed as functions related to the temperature and the strain rate. The experimental and calculated results were found to be in close agreement, which verified the developed model.

The silver fir (Abies alba Mill.) is among the most valuable conifers in Europe for ecological and economic reasons. In the course of history, primarily in the 20th century, its share in stands has been declining due to ill-suited management practices, especially clear-cut management, air pollution, and wildlife-induced damage. Based on recent knowledge of fir ecology and population dynamics, small-scale shelterwood and selection management have been introduced in fir stands, which have also stabilized them. Fir is an essential species for maintaining high stability and biodiversity, especially on planosols and in waterlogged habitats. Due to its shade tolerance and environmental flexibility, particularly at higher altitudes, it can coexist very well with many tree species in mixtures, which can increase the productive potential of stands. It can form stands of heterogeneous structure, ranging from single to multi-layer to selection. For its successful natural regeneration, it is essential to reduce cloven-hoofed game and thus prevent bud browsing damage. On the other hand, fir is a species relatively resistant to bark stripping and the spread of secondary rot compared to Norway spruce (Picea abies [L.] Karst.). During global climate change, fir is expected to shift to higher elevations with sufficient precipitation, while in the southern part of its natural range or at lower elevations, outside water-influenced habitats, it is likely to decline. This paper essentially reviews the description and distribution of the species, its ecological requirements, threats and diseases, habitat and stand conditions, and close-to-nature forest management practices with emphasis on ongoing climate change.

Hybrid reinforcement in a composite material (CM), in many situations, allows better govern material mechanical properties. Polymer matrix CM plate is reinforced with small particles and macro-fibers. Particles are oil shale ash (OSA) powder, macro-fibers – basalt fiber threads im-pregnated by matrix material. With the goal to find out elastic properties of the matrix- polymer with OSA, samples with its different concentrations were experimentally fabricated and their elastic properties were experimentally measured. Obtained data were used in numerical model-ling. Was observed polymer matrix composite slab, reinforced with OSA and three-dimensional (3D) basalt fiber fabric. Fabric are forming threads impregnated by matrix (polymer resin mixed with OSA particles). Damage accumulation in the stretched slab was modelled. Impregnated thread, in the modelling, is observed as a macro-fiber (MF) with averaged elastic properties. With the load increase MF in the material began to break. At first, appeared isolated single breaks. A probabilistic sequential MF rupture accumulation model was accepted and numerical-ly realized. The geometry of the reinforcing knitted fabric was modeled using the Leaf and Glaskin approach. In the knitted fabric highly, stressed MF cross-sections are observed as po-tential location where thread breakage can occur. If one thread breaks, the cross-sections of the adjacent threads experience the overload caused by this rupture. More overloaded crossection in the adjacent overloaded thread breaks and we obtain two adjacent broken MF designated as a defect with the size j=2. The probabilities of obtaining defect consisting of at least 2, 3, … j adjacent broken MF in the plate were calculated. The calculations continued until the rupture process becomes unstable (j→∞). The overstresses on adjacent threads in the CM were calculat-ed using the FEM three-dimensional numerical approach. Analytical and stochastic methods were used for the load-carrying capacity determination and different size defects accumulation in the hybrid composite material (HCM) plate. Also, was calculated the probability of the plate rupture.

This study outlines a 3-step production process for Ti-TiC Metal Matrix Composite (MMC) employing powder Mechanical Blending, Laser Powder Bed Fusion (LPBF), and a heat treatment. A TiC fraction of more than 20 vol% was formed in-situ through the reaction of titanium with carbon during the LPBF process. The manufactured MMC pieces showed a record stiffness and fracture strain combination. The LPBF energy density impacted strongly porosity type. The as-built microstructure displayed an homogeneous distribution of sub-stoichiometric TiC dendrites which were fully converted into equiaxed TiC grains during the heat treatment. The TiC C/Ti ratio was found to be close to 0.5, resulting in an effective reinforcement content nearly twice the one expected for stoichiometric TiC, leading to stronger reinforcement. The mechanical analysis revealed a Young’s modulus of up to 149 GPa and an ultimate tensile strength of up to 770 MPa, indicating a 27% and 34% improvement, respectively, compared to commercially pure Titanium produced by LPBF and heat treated in the same conditions. A fracture strain of up to 2.8% was achieved. The combination of in-situ formation of defect-free TiC reinforcement and subsequent heat treatment enables to reach an exceptional ductility, considering the 20 vol% reinforcement content.

Epoxy powders offer a low-cost means of manufacturing thick section composite parts, such as those found in wind and tidal turbines. Currently, their processing cycle includes a lengthy drying stage (≥ 15 h) to remove ambient moisture. This prevents void defect formation and, thereby, a reduction in mechanical properties, however, it constitutes up to 60% of the processing time. Little research has been published on the study of this process or its optimisation. Experimental and simulated analyses are used to investigate the effects of hygroscopicity in epoxy powder composites. In particular, focus is given to the drying process, which is used to prevent void defect formation and, thereby, a reduction in mechanical properties. As such, tests are performed to quantify the void content of dried and undried laminates, and to measure its impact on transverse flexural strength. Dynamic vapour sorption analysis is used to study the sorption behaviour of the epoxy powder. Sorption data is fitted to a modified linear driving force model, and then implemented in existing process simulations tools. The drying of a thick epoxy powder composite section is simulated to investigate the influence of powder sintering on the duration required for drying. It is shown that the epoxy powder is slightly hygroscopic (1.36 wt%) and exhibits sorption behaviour that is characteristic of glassy polymers. This results in up to 4.8% voids (by volume) if processed in an undried state, leading to a 43% reduction in transverse flexural strength. Process simulations reveal that a standard drying cycle prematurely sinters the powder; inhibiting moisture release. By maintaining a powder state, simulations show that the drying cycle can be reduced to 5 h.

Onychomycosis is a common fungal nail infection for which new antibiotics are needed to overcome antifungal resistance and other limitations of conventional treatments. This study reports the development of antifungal nail lacquers containing oregano essential oil (OEO), rosemary essential oil (REO), and/or biogenic silver nanoparticles (bioAgNP). The formulations (F) were tested against dermatophytes by agar diffusion, ex vivo nail infection, and scanning electron microscopy techniques. They were evaluated pharmacotechnically and by FTIR-PAS to access permeation across the nail plate. F-OEO and F-OEO/Ag were promising for the final nail lacquer formulation, they permeated through the nail plate and showed antifungal efficacy against dermatophytes-contaminated nails after 5 days of treatment. The treated nails had decreased hyphae and spores compared to untreated control; the hyphae were atypically flattened which indicates loss of cytoplasmic content due to damage to cytoplasmic membrane. Formulations were stable after centrifugation and thermal stress, maintaining organoleptic and physicochemical characteristics. F-OEO and F-OEO/Ag had pH compatible with the nail, and drying time (59-90 s) within the reference for nail lacquer. For the first time, OEO and bioAgNP were incorporated in a nail lacquer, resulting in a natural and nanotechnological antifungal product for onychomycosis that may combat microbial resistance.

The development of multidrug resistance by pathogenic bacteria and yeast is a significant medical problem that needs to be addressed. One possible answer could be the combined use of antibiotics and silver nanoparticles, which have different mechanisms of antimicrobial action. Nanoparticles can be combined with antifungal agents in the same way. Biogenic silver nanoparticles synthesized using environmentally friendly technology using extracts of biologically active plants are an effective nanomaterial that needs to be comprehensively investigated for implementation into medical practice. In this study, the synergistic effects arising from their combined use with antibiotics and fungicides against various bacteria and yeasts, included in the ESKAPE list, were studied. Effective concentrations of substances were established, recommendations for the studied pathogenic species were presented and the effect of destruction of the bacterial membrane was illustrated. The most significant synergistic effect was manifested in pathogenic candida and brewer's yeast.

Aluminum (Al) toxicity and low phosphorus availability (LP) are the top two co-existing edaphic constraints limiting agriculture productivity in acid soils. Plants have evolved versatile mechanisms to cope with the two stresses alone or simultaneously. However, the specific and common molecular mechanisms, especially those on flavonoids and carbohydrate metabolism, are still unclear. Laboratory studies were conducted on two wheat genotypes, Fielder (Al-tolerant and P-efficient) and Ardito (Al-sensitive and P-inefficient), exposed to 50 μM Al and 2 μM Pi (LP) in hydroponic solutions. After 4 days of stress, wheat roots were analyzed via transcriptomic and targeted metabolomic techniques. A total of 2296 differentially expressed genes (DEGs, 1535 up and 761 down) under Al and 3029 DEGs (1591 up and 1438 down) under LP were identified in Fielder. Similarly, 4404 DEGs (3191 up and 1213 down) under Al and 1430 DEGs (1176 up and 254 down) under LP were identified in Ardito. The GO annotation analysis results that 4079 DEGs annotated to the metabolic processes term. These DEGs were significantly enriched in the phenylpropanoid, flavonoid, flavone and flavonol biosynthesis, and carbohydrate metabolism pathways by performing the KEGG enrichment analysis. The targeted metabolome analysis detected 19 flavonoids and 15 carbohydrate components in Fielder and Ardito under Al and LP. More responsive genes and metabolites were involved in flavonoid metabolism under LP than Al in the Fielder, while an opposite trend in the Ardito. In the carbohydrate metabolism pathway, the genes and metabolites were higher in Fielder than in Ardito. The combined transcriptome and metabolome analysis revealed that the flavonoid and carbohydrate genes and metabolites differed between Fielder and Ardito under Al and LP, which may be an important reason for Fielder’s high Al and LP resistance. The results of this study lay a foundation for pyramiding genes and breeding multi-resistance varieties.

Micro satellites must survive severe mechanical conditions during their launch phase. Therefore, structural design requirements are imposed on the micro satellites. These requirements are the strength requirement and the stiffness requirement. Usually, the structural design of a micro satellite is performed using the internal stress analysis and the natural frequency analysis, which are based on a Finite Element Method (FEM). The validity of this structural design is evaluated through vibration tests. In an early stage of development, which has a FEM model of a satellite in the process of creation, presumption of the natural frequency of a satellite may be difficult. In this study, a simple method for determining the longitudinal and lateral minimum natural frequencies of the micro satellites during the ascent phase was clarified. The structure of the micro satellites used in this research is made of aluminum alloy, and they have a monocoque structure. The Young's modulus and moment of inertia of area used to calculate the minimum natural frequencies were determined using the area ratio of the monocoque structure to the entire satellite. When this method is used, the estimated minimum natural frequencies of the longitudinal direction and the lateral direction are in agreement with the measured values acquired by the vibration tests. In order to shorten the process of micro satellites development, this paper describes a practical estimation method of the minimum natural frequency for micro satellites.

This work investigated the isothermal holding time dependence of the densification, microstructure, weight loss and tensile properties of Fe-Mn-Si powder compacts. Elemental Fe, Mn and Si powder mixtures with a nominal composition of Fe-28Mn-3Si (in weight percent) were ball milled for 5h and subsequently pressed under a uniaxial pressure of 400 MPa. The compacted Fe-Mn-Si powder mixtures were sintered at 1200 ℃ for 0, 1, 2 and 3 h, respectively. In general, the density, weight loss and tensile properties increased with the increase of isothermal holding time. A significant increase in density, weight loss and tensile properties occurred in the compacts isothermally holding for 1 h, as compared to those with no isothermal holding. However, further extension of isothermal holding time (2 and 3 h) only played a limited role in promoting the density and tensile properties. The weight loss of the sintered compacts was mianly caused by the sublimation of Mn in Mn depletion region on the surface layer of the sintered Fe-Mn-Si compacts. The length of the Mn depletion region increased as isothermal holding time increased. A single α-Fe phase was detected on the surface of all the sintered compacts, and the locations beyond the Mn depletion region were comprised of a dual dominant γ-austenite and minor ε-martensite.

In the discussion on environmental policies, the notion of eco-efficiency is often used. Eco-efficiency is defined as the delivery of products and services with competitive values, while reducing the ecological impacts and satisfying human needs. In an environment of great competitiveness in which the companies operate, the improvements in the productive process is one of the differentiating factors for guaranteeing a strong competition. Also it is essential rationalizing energy consumption and natural resources. For this it is necessary to understand the main operations and dynamics of the company. This work presents an empirical study of a Portuguese company in the industrial sector. The problematic here presented is based on the company’s growing concern to reduce the amount of scrap produced. From the literature research that was performed, a strong dependence relation between the different variables in the extrusion process was found. The main objective of this work is to model the aluminium extrusion process, with the aim of minimizing the production of scrap. For this several variables involved in the process are taking into account. Using statistical techniques, in particular multiple linear regressions, it was possible to identify the importance of the variables under study for the scrap production.

Aluminum matrix nanocomposites have been the subject of much attention due to their extraordinary mechanical properties and thermal stability. This research focuses on producing and characterizing an aluminum matrix reinforced with silicon carbide (SiC) nanometric particles. The conventional powder metallurgy route was used to produce the nanocomposites, and the dispersion and mixing process was carried out by ultrasonication. The conditions of the dispersion and the volume fraction of the SiC were evaluated in the production of the nanocomposites. Microstructural characterization was carried out using optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron backscatter diffraction (EBSD). Mechanical characterization was carried out using hardness and tensile tests. The dispersion agent was investigated, and isopropanol leads to better dispersion with fewer agglomerates. Increasing the volume fraction of the reinforcement improves the hardness of the nanocomposites. However, greater agglomeration of the reinforcement is observed for larger volume fractions. The greatest increase in hardness (77% increase compared to the hardness of the Al matrix) is obtained with 1.0 vol % of SiC, corresponding to the sample with the best dispersion. The mechanical characterization through tensile tests attests to the effect of the reinforcement on the Al matrix. The main strengthening mechanisms identified were the load transfer, the texture hardening, Orowan strengthening, and the increase in the density of dislocations in the nanocomposites.

Lattice structures have emerged as promising materials for aerospace structures applications due to their high strength-to-weight ratios, customizable properties, and efficient use of materials. These properties make them at-tractive for use in anti-ice systems, where lightweight and heat exchanging are essential. This paper presents an extensive experimental investigation into mechanical compression properties of lattice trusses fabricated from AlSi10Mg powder alloy, a material commonly used in casted aerospace parts. The truss structures were manufactured using additive manufacturing Selective Laser Melting technique and subjected to uniaxial compressive loading to assess their performance. The results demonstrate that AlSi10Mg lattice trusses exhibit remarkable compressive strength with strong correlations depending upon both topology and cells’ parameters setup. The finding described highlights the potential of AlSi10Mg alloy as a promising material for custom truss fabrication, offering customizable cost-effective and lightweight solutions for aerospace market. The paper also emphasizes the role of additive manufacturing in producing complex structures with pointwise tailored mechanical properties.

Electromobility promises to efficiently mitigate consequences of increasing traffic volume and its accompanied greenhouse gas emissions. On an individual level, electrified bikes allow emission free electrified mobility at moderate costs and consequently their stock has increased significantly in recent years. This simultaneously increases the demand for spare parts, which are often manufacturer or application-specific, and due to many variants, challenging to provide for the market. This article evaluates powder-based and extrusion-based metal additive manufacturing of a typical electrified bike component to demonstrate an alternative spare parts supply. The investigation demonstrates how these parts can be additively manufactured function equivalent and with sufficient mechanical properties, also taking economical aspects into account. Furthermore, the needed resources and related environmental consequences for metal-based additive manufacturing spare-part production are compared for both process routes. The results show that both routes are capable of producing spare-parts at comparatively same mechanical performance and resource costs, while needed resources such as energy, gases and manufacturing time are significantly lower for powder-based, respectively machine costs for extrusion-based additive manufacturing. Therefore, additive manufacturing offers a promising opportunity to produce parts in small quantities resource efficient and rapidly.

The advancement of performance in the domain of flexible wearable strain sensors has become increasingly significant due to extensive research on laser-induced graphene (LIG). An innovative doping modification technique is required owing to the limited progress achieved by adjusting laser parameters to enhance LIG’s performance. By pre-treating with AgNO3, we successfully manufactured LIG with a uniform dispersion of silver nanoparticles across its surface. The experimental results for the flexible strain sensor exhibit exceptional characteristics, including low resistance (183.4 Ω), high sensitivity (426.8), a response time of approximately 150 ms, and a relaxation time of about 200 ms. Moreover, this sensor demonstrates excellent stability under various tensile strains and remarkable repeatability during cyclic tests lasting up to 8,000 s. Additionally, this technique yields favorable results in finger bending and hand back stretching experiments, holding significant reference value for preserving the inherent characteristics of LIG preparation in a single-step and in situ manner.

Aluminum (Al), making up a third of the Earth's crust, is a widespread toxic contaminant, particularly in acidic soils. It impacts crops at multiple levels, from the cellular to the whole plant. This review delves into aluminum's reactivity, including its cellular transport, involvement in oxidative redox reactions, development of specific metabolites, and the influence of genes on the production of membrane channels and transporters, as well as its role in triggering apoptosis leading to senescence. It discusses the involvement of channel proteins in calcium influx, vacuolar proton pumping, the suppression of mitochondrial respiration, and the initiation of programmed cell death. At the cellular nucleus level, the effects of Al on gene regulation through alterations in nucleic acid modifications, such as methylation and histone acetylation, are examined. The review in addition outlines the pathways of Al induced metabolic disruption specifically citric acid metabolism, regulation of proton excretion, induction of specific transcription factors, modulation of Al-responsive proteins, changes of citrate and nucleotide glucose transporters and overall metal detoxification pathways in tolerant genotypes. It also considers the expression of phenolic oxidases in response to oxidative stress, their regulatory feedback on mitochondrial cytochrome proteins, and their consequences on root development. Ultimately, the review focuses on the selective metabolic pathways that facilitate Al exclusion and tolerance, emphasizing compartmentalization, antioxidative defense mechanisms, and the control of programmed cell death to manage metal toxicity.

Abstract composite silver nanoparticles were synthesised using melanin broth and Arabic gum as a reducing and binding agent. The reactions are carried out with water because it is a non-hazardous solvent. The produced composites either had specified diameters (average diameter of 50 nm) with high silver loading or lower loading composites with tuneable morphologies and electrical properties. UV-IR, gamma, and conventional light are used to characterise the synthesised composite silver nanoparticles. Furthermore, measurements are carried out of the dielectric constant, refractive index, energy gap, optical and electrical conductivities, and refractive index coefficients. The silver nanoparticle formation was validated by UV-Vis measurement of the sample, which demonstrated a distinct peak at a wavelength of 420 nm. The characteristics of the composite silver nanoparticles are also quantified using several methods, including XRD, SEM, and particle size analysis.

The adulteration of goat milk powder occurs frequently, cattle-derived and soybean-derived ingredients are common adulterants in goat milk powder. However, simultaneously and rapidly detecting cattle-derived and soybean-derived components is still a challenge. high throughput and efficient screening method for adulteration detection is need. In this study, a rapid method was developed to detect the adulteration of common cattle-derived and soybean-derived components simultaneously in goat milk powder by combining the CRISPR/ Cas12a system with recombinant polymerase amplification (RPA). A dual DNA extraction method was employed, primers and crRNA for dual detection were designed and screened, and a series of condition optimizations were carried out in this experiment. The optimized assay can rapidly detect cattle-derived and soybean-derived components in 40 min. The detection limits of both cattle-derived and soybean-derived components were 1% (w/w) for the mixed adulteration models. The established method was applied into a blind survey of 55 commercially available goat milk powder products. The results showed that 36.36% of the samples contained cattle-derived or soybean-derived ingredients, which revealed the noticeable adulteration situation in the goat milk powder market. This study realizes a fast flow of dual extraction, dual amplification and dual detection of cattle-derived and soybean-derived components in goat milk powder for the first time. It can be used for high-throughput and high-efficiency on-site primary screening of goat milk powder adulterants, and provide a technical reference for combating with food adulteration.

Chromium (Cr) metal has garnered significant attention in alloy systems owing to its exceptional properties, such as high melting point, low density, and superior oxidation and corrosion resistance. However, its processing capabilities are hindered by the high Ductile-Brittle Transition Temperature (DBTT). Recently, powder bed fusion-laser beam for metals (PBF-LB/M) has emerged as a promising technique, offering the fabrication of net shapes and precise control over crystallographic texture. Nevertheless, research investigating the mechanism underlying crystallographic texture development in pure Cr via PBF-LB/M still needs to be conducted. This study explores the impact of scan speed on relative density and crystallographic texture. At the optimal scan speed, an increase in grain size attributed to epitaxial growth was observed, resulting in the formation of cubic texture. Consequently, a reduction in High Angle Grain Boundaries (HAGB) was achieved, suppressing defects such as cracks and enhancing relative density up to 98.1%. Furthermore, with increasing densification, Vickers hardness also exhibited a corresponding increase. These findings underscore the efficacy of PBF-LB/M for processing metals with high DBTT properties.

Impure and pure casts have collected reasonable attentions over all the world. In this paper, Aluminum (Al) and Copper (Cu) cast alloys are considered to be studied. Multiple impure and pure Al-Cu cast alloys are established under the condition of very high temperatures. Then, all of the established alloys are examined by applying mechanical tests. More specifically, tests of hardness are exploited. Moreover, different quenching conditions are employed and analyzed. These are the water, air and oil. Consistent results are separately obtained for the impure and pure materials.

Plasmonic sensors have great potential for widespread usage, but the prohibitive cost of noble metals restrains the wider adoption of this technology. The aim of our study is to develop a cost-effective Al-based alternative to plasmonic detectors commonly based on noble metals. We considered a structure that consists of a Si p-n junction with an overlying grating-relief aluminum layer. The investigation of the infrared plasmonic resonance dependency on the structure geometric parameters and optimization of the fabrication process allowed us to determine optimal parameters for photodetection enhancement. The resonance photoresponse of optimized aluminum-based plasmon-polariton photodetector was significantly improved and became comparable to noble metal-based analogs. Our results can be used for the creation of cost-effective high-sensitivity plasmonic sensors.

Crystalline silver thin layers were obtained by high-energy pulsed laser ablation without heating of the deposition substrate. The fluid Plateau-Rayleigh (PRI), Rayleigh – Taylor (RTI) and Richtmyer – Meshkov (RMI) instabilities, as well as crown splash induced during pulsed laser deposition (PLD) in high energy regime, resulting in ring and pearl shaped structures, offer the benefit of increased sorption surface. These morphological structures obtained for the silver thin layers make them of interest for catalytic applications. The study presented with this work addresses both the fundamental and applied issues on the morphological structures obtained for the silver thin layer and their catalytic function in organic processes. In this sense, the catalytic action of the thin silver layer was highlighted by modifications of the Reactive Blue 21 dye (C.I.) in aqueous solution with sodium bicarbonate. Specific investigations and analyzes were carried out by electron microscopy and elemental analysis (SEM-EDX), atomic force microscopy (AFM) and profilometry, mass spectrometry, ablation plasma diagnosis, diffractograms (XRD), as well as IR spectroscopy (FTIR). In addition to the experimental investigation and analyzes, simulation of the ionization energy threshold was conducted in COMSOL for complementary evaluation on the involved processes and phenomena.

Goat milk is a nutritious food, with high levels of vitamins and minerals. In this context, there is a growing need to improve preservation techniques. Thus, the present work was developed with the aim of drying goat milk using a spray dryer. Chemical, physical, and physicochemical analyses of powdered goat milk and reconstituted goat milk were performed, as well as the characterization of raw goat milk. The statistical model used was the full factorial design 2³ + 3, observing the Pareto Diagram and Analysis of Variance to study the effect of atomization frequency (Hz), inlet temperature (°C), and peristaltic pump rotation (rpm) on the responses for the powdered and reconstituted product. The planning was executed with eleven trials, including nine different trials and three central points. For the analysis of the planning at a 95% confidence level, the Statistica 8.0 software was used. The results showed that atomization frequency and inlet temperature had the greatest effect on the powdered product and the reconstituted food, respectively. Therefore, the importance of drying this food is evident as it offers several advantages for the food industry and consumers.

A special vibration damper is proposed for material property identification through a scratching process on a vibrating object. This paper presents the design and working principle of a scratching damper based on a scratch test device. A non-contact electromagnetic shaker is used to generate the shaking force for the vibration of the tested object. The required pressure on the scratched material during the scratching process is generated by a compression spring and adjusted by changing the amount of compression of the spring. The proposed damper is designed and tested on extruded aluminum samples for the determination of its Young’s modulus and hardness and validated by using the standard test instruments. Observations of physical dimensions of the scratching tracks are determined by microscope and were utilized to compute the scratching energy factor. Load curves are obtained at different pressure of the scratching process. The hysteresis loop energy during the scratching process of the tested object is measured and used for the determination of material properties of the object. Furthermore, energy conservation law, scratch energy release rate and loop energy release rate are used to determine the Young’s modulus and hardness of the sample. The measurement accuracy of the modulus and hardness of the tested sample is evaluated. The proposed method of material testing has several advantages over the traditional methods such as low cost and high repeatability, and may be used as an alternative to the standard modulus and hardness testers.

Aluminum wire is a common material for wire bonding due to its resistance to oxidation and low price. It does not melt when becoming a free air ball (FAB) during the electronic flame-off (EFO) process with wettability, and is applied by wedge bonding. This study used 20μm Zn-Coated Al-0.5wt.%Si (ZAS) wires to improve the FAB shape after the EFO process, while maintaining stability of the mechanical properties, including the interface bonding strength and hardness. In order to test circuit stability after ball bonding, the current-tensile test was performed. During the experiment, it was found that 80nm ZAS with wire bonding has lower resistance and higher fusing current. For the bias tensile test, the thicker Zn film diffused into the Al-Si matrix easily, after which the strength was reduced. The ball-bond interfaces had no change in their condition before and after the bias. Accordingly, ZAS could be a promising candidate for ball bonding in the future.

In this work, studies were carried out on the extraction of silver and gold from cakes of pressure oxidation leaching of sulfide concentrate containing pyrite and arsenopyrite. The addition of gypsum at a consumption of 0.1 g/g of concentrate helps to increase silver extraction from 13.4 to 95–98% at the cyanidation stage, with no conditioning operation. Gold recovery was 99%. An increase in gypsum consumption contributes to the formation of BFAS with an increased content of sulfate sulfur, and a decrease in the As/S(sulfate) molar ratio in the cake from 3.7 down to 0.88 contributes to an increase in silver extraction at the cyanidation stage up to 98%, and its further decrease from 0.88 down to 0.58 leads to a gradual reducing silver transfer into solution from 98 down to 75.1% at the cyanidation stage. Basic ferric sulfate (BFS) is not formed in this case, since according to EDS mapping the distribution of arsenic and sulfur over iron-containing particles is uniform. According to TCLP analysis, the cake obtained after pressure oxidation leaching with the addition of gypsum and cyanidation is stable and suitable for disposal, since the final concentration of arsenic in the solution was 0.45 mg/dm3.

Lap joints were friction stir welded in AA 7075-T6 at 1320 rpm and using two welding speeds: 70 mm/min and 120 mm/min. The temperature profiles of the weld zone were registered during the process; furthermore, the microhardness, tensile strength, and microstructure of the joints produced were examined. This study brings new insights into the thermomechanical behavior of the material during the process. The peak temperature obtained with the lower welding speed (70 mm/min) is 10% higher than that obtained with the higher speed (120 mm/min). Moreover, a 5% increase in microhardness and a 6% increase in tensile strength were were observed increasing the welding speed. Addition-ally, the microstructure examination demonstrated that, by decreasing the welding speed, the larger interaction between the tool and the material results in a deeper stir zone due to the increased heat diffusion downwards to the material. This heat flow affects the thermal profile and influences the resulting mechanical properties of the welded joints.

Polyelectrolyte-drug complexes are interesting alternatives to improve unfavourable drugs properties. Vancomycin (VAN) is an antimicrobial used in the treatment of methicillin-resistant Staphylococcus aureus pulmonary infections in patients with cystic fibrosis. It is generally administered intravenously with high incidence of adverse side effects, which could be reduced by intrapulmonary administration. Currently, there are no commercially available inhalable formulations containing VAN. Thus, the present work focuses on the preparation and characterization of an ionic complex between hyaluronic acid (HA) and VAN with potential use as inhalable formulations. Particulate-solid HA-VAN25 complex by spray drying from an aqueous dispersion was obtained. FTIR spectroscopy and thermal analysis confirmed the ionic interaction between HA and VAN, while an amorphous diffraction pattern by X-ray was observed. The powder density, geometric size and morphology showed a suitable aerosolization and aerodynamic performance of the powder, indicating the capability of reaching the deep lung. An in vitro extended-release profile of VAN from the complex was obtained, exceeding 24 hours. Microbiological assays against methicillin-resistant and -sensitive reference strains of Staphylococcus aureus, showed that VAN preserves its antibacterial efficacy. In conclusion, HA-VAN25 exhibited interesting properties for the development of inhalable formulations with potential efficacy and safety advantages over conventional treatment.

This research has developed a process for producing ZnO thin film from DEZn deposited onto a PET substrate with low-pressure, high-frequency Ar + O2 plasma using a chemical vapor deposition technique. The aim is to study the film production conditions that affect electrical properties, optical properties, and thin film surfaces. This work highlights the use of plasma energy produced from a mixture of gases between Ar + O2. Plasma production is stimulated with an RF power supply to deliver high chemical energy and push ZnO atoms from the cathode inside the reactor onto the substrate through surface chemical reactions. The results showed that increasing the RF power in plasma production affected the chemical reactions on the substrate surface of film formation. The film preparation at RF power 300 W will give the thickest films. The film has a continuous columnar formation, and the surface has a granular structure. This results in the lowest electrical resistivity of 1.8 x 10-4 Ω-cm. In addition, when fabricated into a DSSC device, the device tested the PCE value and showed the highest value at 5.68%. This is due to the very rough surface nature of the ZnO film, which increases the scattering and storage of sunlight, making cells more efficient. Therefore, the benefit of this research is that it will be a highly efficient prototype of thin film production technology using a chemical process that reduces production costs and can be used in the industrial development of solar cells.

Silver iodide (AgI) is a system prototype allowing the flow of ions through its structure and has a phase transition at 420 K, characterized by an abrupt change in conductivity and a high ionic conductivity. Introducing low concentrations of graphite (C) into the AgI structure produces a new material with a mixed conductivity (ionic and electronic) which increases with increasing temperature. The experimental results of the logarithm of the ionic conductivity as a function of the inverse of temperature for the (AgI)x–C(1−x) system for low carbon concentrations 0.97 ≤ x ≤ 0.99 were well fitted using a phenomenological model with a probability distribution for the charge carriers based on the carrier density

This paper aims to review the challenges, toxicity, and routes of synthesis and usage of silver nanoparticles in different applications but also highlighting their sustainability from both medical and environmental issues. Regarding their toxicity, it is known that silver nanoparticles can destroy over 650 microorganisms comparing with antibiotics. Supplementary, will be presented in a comparative manner some conventional synthesis routes (physical and chemical methods) and green synthesis routes using plant extracts. The approach using plant extracts have various advantages comparing with physical, chemical and microbial synthesis methods because there is no need to use chemicals, wasteful purifications and high energy requirements. The paper presents an overview on “green nanotechnology” focused on using either biological micro-organisms or plant extracts as an alternative to the classical chemical and physical methods. An important issue discussed in the paper is an overview of the synthesis routes of silver nanoparticles, some expected applications of silver based active agents and their toxicity and challenges that must be overcome. Also, it needs to focus our attention on the dismissal of silver nanoparticles into the environment and especially in water systems, fact which suggests that this issue must be fully understood and applied the law.

This work communicates analysis of aluminum monoxide, AlO, laser-plasma emission records using line strength data and the ExoMol astrophysical database. A nonlinear fitting program computes comparisons of measured and simulated diatomic molecular spectra. Predicted cyanide spectra of the AlO, ${\rm B}\ ^2\,\Sigma^+ \longrightarrow {\rm X} \ ^2\,\Sigma^+$, $\Delta {\rm v} = 0, \pm 1, \pm 2, + 3$ sequences and progressions compare nicely with 1 nanometer resolution experimental results. The analysis discusses experiment data captured during laser ablation of Al$_2$O$_3$ with 266-nm, 6-mJ pulses. The accuracy of the AlO line strength data is better than one picometer. This work presents as well comparison of the $^{27}$Al$^{16}$O line strength and of ExoMol data for spectral resolutions of 0.1nm and 0.07nm. Accurate AlO databases show a volley of applications in laboratory and astrophysical plasma diagnosis.

For the first time, an environmentally friendly waste-free closed cycle for the formation of EMI shielding materials that are promising for 5G communications is considered. Based on the proposed closed technological cycle, two types of EMI shielding materials have been obtained; both materials have significant prospects for signal shielding in all ranges that are allocated in different countries for 5G communication. The first type of materials are transparent conductive meshes with a transparency of more than 80% and with a shielding efficiency of more than 40 dB in the S and L bands and about 30 dB in the K and Ka bands. The study of signal reflection characteristics in the S, L, C, K and Ka bands showed the promise of using these materials as transparent 5G signal reflectors. The reflection coefficient in all considered ranges is above 90% (-0.5 dB). The second type of shielding material are continuous silver micro caps films characterized by a shielding efficiency of 90.1 dB at a thickness of 6.2±1.2 µm. We have also shown that silver micro caps can separate into silver flakes and ribbons when sonicated. These materials can also be used to produce EMI shielding coatings and composites. A detailed analysis of the shielding properties showed that each type of materials obtained in a closed technological cycle is comparable with the best literature results and significantly wins in terms of cost.

The Huaniushan lead-zinc-silver deposit is a hydrothermal sedimentary exhalative deposit (SEDEX). The mining area has complex geological conditions. The main tectonic structure in the area is the Huaheitan-Shuangfengshan Fault (F3), which controls the distribution of strata and magmatic rocks. Since the discovery of the Huaniushan Lead-zinc-silver polymetallic deposit, there are diverse understandings of the deposit's genesis and mineralization law, making it challenging to meet the geological interpretation requirements of the Huaniushan Lead-zinc-silver polymetallic deposit. Moreover, a single geophysical exploration method utilizes limited rock physical parameters, making it difficult to effectively characterize underground structures. The integrated exploration of multiple geophysical methods can effectively integrate the geophysical characteristics of different rock physical parameters, reducing the multiplicity and uncertainty of geophysical data inverse interpretation. The comprehensive interpretation of three-dimensional inversion based on various geophysical data, the construction of geological-geophysical models based on geological grounds, the establishment of hidden ore exploration and positioning, and the rapid evaluation of geophysical technology systems are the current development trends in mineral exploration. In light of this, this paper conducts research on the three-dimensional inversion interpretation of the heavy magnetoelectric exploration data of the Huaniushan sedimentary exhalative deposit lead-zinc-silver polymetallic deposit in the mining area and constructs a three-dimensional geological-geophysical model of the study area based on the obtained three-dimensional physical structure of the underground three-dimensional density, magnetization intensity, resistivity, and polarizability structure of the study area, in combination with the information of related geology and drilling holes. It comprehensively interprets the favorable mineralization parts in the study area.

Laser Powder Bed Fusion (LPBF), as a transformative technology in the field of additive manufacturing, offers unprecedented design flexibility and material efficiency. This review paper delves into the latest advancements in LPBF technology and the various alloys used in the process, including titanium alloys, aluminum alloys, nickel-based superalloys, steel alloys, copper alloys, and high-entropy alloys. For each alloy category, we discuss their specific applications, performance characteristics, and challenges faced in LPBF usage. The paper discusses important technological breakthroughs, including innovations in laser systems, scanning strategies, and in-situ monitoring technologies, which have enhanced the precision and reliability of LPBF.

Additive manufacturing (AM) is today’s buzzword—and not only in commercial production. One of the AM techniques produces 3D objects with complex geometry using a laser beam. The relationship between the morphology of individual powder particles and the printing process has not been adequately documented yet. This article presents a detailed microscopic analysis of virgin and reused powder particles of maraging steel. Metallographic observation was performed using a scanning electron microscope (SEM). Detailed analyses of individual particles were carried out using SEM with a focused ion beam (FIB) milling capability. Analyses of elemental distribution and phase distribution were performed using EDS and EBSD, respectively. The findings have led to a better understanding and prediction of defects in additive-manufactured products.

In this study, we report the antibacterial mechanisms of action of uniform silver nanoparticles (AgNPs) and decorated activated carbon nanocomposite (CAC-AgNPs) obtained using a green synthesis approach. The nanomaterials were characterized by ultraviolet-visible (UV-vis) absorption spectra and Fourier transform infrared (FTIR) spectra. The antibacterial activity of the as-prepared nanomaterials was evaluated against an array of bacterial strains by microdilution method, whereas their cytotoxicity profile was evaluated on Vero cells (human mammalian cells). The antibacterial mechanistic studies of active nanomaterials were carried out through bacterial growth kinetics, nucleic acid leakage test, and catalase inhibition assay. A silver nanocomposite was successfully fabricated from Croton macrostachyus-based activated carbon. The as-prepared nanomaterials exhibited antibacterial activity against an array of bacterial strains (minimum inhibitory concentration (MIC) range: 62.5 to 500 µg/mL), the most susceptible being Escherichia coli and Staphylococcus aureus. Cytotoxicity studies of the nanomaterials on Vero cells revealed that the nanocomposite (median cytotoxic concentration (CC50): 213.6 µg/mL) was less toxic than the nanoparticles (CC50 value: 164.75 µg/mL) counterpart. Antibacterial mechanistic studies unveiled that the nanomaterials induced (i) bacteriostatic activity vis-à-vis E. coli and S. aureus and (ii) inhibition of catalase in these bacteria. This novel contribution on the antibacterial mechanisms of action of silver nanocomposite from C. macrostachyus-based activated carbon might contribute to the understanding of antibacterial action of these biomaterials. Nevertheless, more chemistry and in vivo experiments, as well as in depth antibacterial mechanistic studies are warranted for the successful utilization of these antibacterial biomaterials.

The dimethylaminophenyl-substituted silver phthalocyanine [dmaphPcAg] can be used as a UV-vis photoinitiator for in situ preparation of a silver/polymer nanocomposite. To verify early steps of the supposed mechanism of radical polymerization, we performed quantum chemical calculations of m[dmaphPcAg]q complexes with charges q = +1 to -2 in the two lowest spin states m, of a free ligand and its dehydrogenated/deprotonated products m[dmaphPcHn]q, n = 2 to 0, q= 0, -1 or -2, in the lowest spin states m. The calculated electronic structures and electron transitions of all the optimized structures in CHCl3 solutions are compared with experimental EPR and UV-vis spectra, respectively. The unstable 3[dmaphPcAg]+ species deduced only from previous EPR spin trap experiments was identified. In addition to 2[dmaphPcAg]0, our results suggest the coexistence of both reaction intermediates 1[dmaphPcAg]- and 3[dmaphPcAg]- in reaction solutions. Silver nanoparticle formation is a weak point of the supposed reaction mechanism from the energetic, stereochemistry, and electronic structure points of view.

Nanoparticles (NPs) have uniform chemical composition, size, and morphology. Microorganisms are of great interest in Nanoparticle synthesis. The green production of nanomaterials occurs either intracellularly or extracellularly. Gold and silver nanoparticles are mostly synthesised by the enzymatic degradation of metal ions. The produced NPs are characterized by different instruments such as ultraviolet visible, dynamic light scattering, x-ray diffraction, scanning electron microscope, transmission electron microscope, etc. Our review discusses the various biomedical applications of gold and silver nanoparticles synthesized by microbes via intracellular and extracellular mechanisms.

Background. Nanotechnology is promising field for generating new applications. A green synthesis of nanoparticles through biological methods using plant extract have a reliable and ecofriendly approach to improve our global environment. Methods. Silver nanoparticles (AgNPs) were synthesized using aqueous extract of Anagalis arvensis L and silver nitrate and were physicochemically characterized. Results. The stability of AgNPs toward acidity, alkalinity, salinity and temperature showed that they remained stable at room temperature for more than two months. The SEM and TEM analysis of the AgNPs showed that they have a uniform spherical shape with an average size in the range of 40–78 nm. Further 1-Dibhenyl-2-Picrylhydrazl radical in Anagalis arvensis L.mediated AgNPs showed a maximum activity of 98% at concentration of 200μg/mL. Hydrogen peroxide scavenging assay in Anagalis arvensis L. mediated AgNPs showed a maximum activity of 85% at concentration of 200μg/mL. Reducing power of Anagalis arvensis L.Ag NPs exhibited a higher activity of 330 μg/mL at concentration of 200 μg/mL. These NPs have cytotoxic effects against brine shrimp (Artemia salina) nauplii with a value of 53% LD 178.04μg/mL. Conclusion. The AgNPs synthesized using Anagalis arvensis L. extract demonstrate a broad range of applications.

The characteristics of powders on a bulk scale are heavily influenced by both the material properties and the size of their primary particles. Throughout the stages of storage and transportation in the powder processing industry, various forms of deformation and stress, such as pressure and shear, impact these materials. Recognizing the point at which a powder undergoes yielding becomes particularly significant in numerous applications. There are also times when you need to understand the level of stress needed to maintain it. Measurement of powder yield and flow properties remains a challenge and is addressed in this study. As part of the CALIPER collaborative project, a number of shear experiments were performed using two shearing devices: Schulze ring shearing device and Anton Paar Powder Cell (APCC). These experiments have three purposes: i) Test reproducibility/consistency between two shear devices and test protocols. ii) To relate bulk behavior to microscopic particle properties, focusing on bulk density and thus the effect of cohesion between particles; iii) Investigate the influence of the temperature of heated powders on the powder flow properties, which is important for the industrial reactors. Interestingly, for samples with small particle size, bulk cohesion increases slightly, but bulk friction increases significantly, because of particle interaction effects. The experimental data not only provide useful insight into the role of microscopically attractive van der Waals gravitational and/or compressive forces on the macroscopic flow behavior of bulk powders, but also have industrial relevance. We also provide a robust datas of cohesive and attritional fine powder for silo design used for calibration and validation of silos, models and computer simulations.

A critical challenge underpinning the adoption of Additive Manufacture (AM) as a technology is the postprocessing of manufactured components. For Selective Laser Sintering (SLS) this can involve the removal of powder from the interior of the component, often by vibrating the component to fluidise the powder to encourage drainage. In this paper we develop and validate a computational model of the flow of metal powder suitable for predicting powder removal from such AM components. The model is a continuum Eulerian multiphase model of the powder including models for the granular temperature; the effect of vibration can be included through appropriate wall boundaries for this granular temperature. We validate the individual sub-models appropriate for AM metal powders by comparison with in-house and literature experimental results, and then apply the full model to a more complex geometry typical of an AM Heat Exchanger. The model is shown to provide valuable and accurate results at a fraction of the computational cost of a particle-based model.

The application of solvent method in the preparation of polypropylene powders was investigated, including the influence of various technological conditions, such as the raw material melt index of polypropylene, processing temperature, dosage of the solvent and the packing pressure. The experimental data show that using solvent method can effectively produce polypropylene powder, and the optimal technological conditions are: melt index of polypropylene being about 17.8 g/10min, processing temperature being about 166.0 ℃, dosage of the solvent being about 0.067g/ml and the packing pressure being about 0.7MPa.Under this technological conditions, polypropylene powder with excellent sphericity could be prepared, the apparent density of powder can reach 0.40 g/cm3 and the prepared powder displayed a narrow size distribution with the mean size of about 42.7 µm.

Magnesium and Aluminum alloys continue to be important in the context of modern and lightweight technologies. With the advancement of additive manufacturing (AM), components can be produced directly in a net shape, widen up the usage of magnesium and aluminum alloys as well as holding new ideas for the application of unique physical structures made feasible by 3D printing. Laser-based approach, one of the metal additive manufacturing (AM) methods, enables the formation of arbitrary 3D structures. With promising findings, research in this area is advancing quickly, bringing up a variety of potential applications in both the scientific and industrial sectors. Complex structures can now be manufactured easily utilizing AM technologies to meet the pre-requisite objectives like reduced part numbers, greater functionality, and lightweight, among others. AM has the ability to meet demands by lowering costs and speeding up the manufacturing process. Due to their popularity in numerous high-value applications, aluminum, and magnesium alloys are one of the key material systems being researched in the laser-based additive manufacturing approaches. The review here aims to comprehensively examine the additive manufacturing of magnesium and aluminum alloys, highlighting the influence of the laser-based additive manufacturing approach on the mechanical characteristics, microstructure, and tribological performance of magnesium and aluminum alloys.

The invention of nanoscience not only brings a revolutionary change in the field of science but also changed the direction of research. Today the whole world is under the trigger of nano and nanoparticles have multidimensional applications in every aspect of life including environmental point of view. Till today a plethora of nanoparticles have been synthesized and have also been applied for multiple purposes and hence grabbed the attention of researchers all over the world. Among the bunch of NPs discovered to date, we have a particular interest in silver nanoparticles (AgNPs) because of their cost-effectiveness and huge abundance in the earth’s crust. With respect to every passing day, due to various kinds of anthropological activities, the quality of the environment such as air, water and soil is depleting which ultimately hampers the human civilization. To encompass the growing environmental issues, many techniques have been adopted. Among the many strategies, tackling the current issues regarding environment through nanoscience is highly worthy as because of its cost-effectiveness, less time consuming and easy handling process. This article reviews the potential of nanoparticles, particularly silver nanoparticles, for a wide range of environmental applications, such as soil, air, and water remediation.

Micro- and nanoflowers are a class of materials composed of particles with high surface-to-volume ratio. They are being extensively studied in the last decade due to simple preparation protocols and promising applications in biosensing, as drug delivery agents, for water purification and so on. Flowerlike objects, due to their highly irregular surface, may act also as plasmonic materials, providing resonant coupling between optical waves and surface plasmon excitations. This fact infers for the possibility to use micro- and nanoflowers as effective surface-enhanced Raman scattering (SERS) substrate materials. Here, we report on the design and Raman enhancement properties of silver flowerlike structures, deposited on aluminum surface. A simple and cost-effective fabrication method is described, which leads to SERS substrates of high developed surface area. The morphology of the silver flowers on a nanoscale is characterized by self-organized quasiperiodic stacks of nanosheets, which act as plasmonic cavity-resonators. The substrates were tested against rhodamine-6G (R6G) water solutions of concentration varying between 10^–3 M and 10^–7 M. Optimal SERS enhancement factors of up to 10⁵ were established at R6G concentrations in the range 10^–6 – 10^–7 M.

Biosynthesis of nanoparticles for delivery of therapeutic agents has introduced new opportunities in upgrading medical treatment. Plant extracts contains different capping and reducing agents naturally thus provided simpler and less expensive way to synthesize AgNPs. In present work, Citrus reticulata mediated stabilised AgNPs was synthesized. Optimum concentration of reactants was achieved by varying the amount of extracts (1-11 ml) and AgNO₃ concentration (0.5-3 mM). Surface Plasmon peak of Citrus reticulata mediated AgNPs was determined by UV-visible spectrophotometer and functional groups of capping agents were examined by FTIR analysis. Surface Plasmon peaks of Citrus reticulata fresh peel, seed, and juice extracts were observed at 420 nm. But in dry peel extract, absorption peak of AgNPs appeared at 410 nm. Colour of different extracts was changed after the reduction of AgNO₃ to AgNPs by reducing agents present in the extracts. FTIR analysis showed band peaks at 3316 cm-1 correspond to amide (N-H and O-H) stretching vibrations while alkanes peaks was observed at 1638 cm-1 which showed C=C stretching aromatic ring (flavonoids). Furthermore, Citrus reticulata fresh peel mediated AgNPs showed impressive stability up-to 112 days. In conclusion, Citrus reticulata fresh peel extract provided an excellent source of reducing agents for synthesizing stabilized AgNPs.

Background: Heracleum sphondylium, a medicinal plant used in Romanian ethnopharmacology, proved to have a remarkable biological activity. The escalating concerns surrounding antimicrobial resistance led to a special attention to new efficient antimicrobial agents based on medicinal plants and nanotechnology. We report the preparation of a novel, simple phytocarrier that harnesses the bioactive properties of H. sphondylium and silver nanoparticles (HS-Ag system). Methods: The H. sphondylium low-metabolic profile was determined through gas chromatography–mass spectrometry and electrospray ionization–quadrupole time-of-flight–mass spectrometry. The morphostructural properties of the innovative phytocarrier were analyzed by X-ray diffraction, Fourier-transform infrared spectroscopy, Raman spectroscopy, dynamic light scattering, scanning electron microscopy, and energy-dispersive X-ray spectroscopy. The antioxidant activity was evaluated using total phenolic content, ferric reducing antioxidant power, and 2,2-diphenyl-1-picrylhydrazyl (DPPH) in vitro assays. The antimicrobial activity screening against Staphylococcus aureus, Bacillus subtilis, Pseudomonas aeruginosa, and Escherichia coli was conducted using the agar well diffusion method. 3-(4,5-Dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide (MTT) assay estimated the in vitro potential cytotoxicity on normal human dermal fibroblasts (NHDF) and cervical cancer (HeLa) cells. Results: A total of 88 biomolecules were detected, such as terpenoids, flavonoids, phenolic acids, coumarins, phenylpropanoids, iridoids, amino acids, phytosterols, fatty acids. HS-Ag phytocarrier heightened efficacy in suppressing the growth of all tested bacterial strains compared to H. sphondylium and exhibited a significant inhibition of HeLa cell viability. Conclusions: The new HS-Ag phytocarrier system holds promise for a wide range of medical applications. The data confirms the capacity to augment pertinent theoretical understanding in the innovative field of antimicrobial agents.

At present, in the field of aviation industry, titanium alloy is mainly used to manufacture parts such as compressor disc, blade and casing of aircraft engine. When working, titanium alloy parts produce high temperature due to high-speed running friction, which makes the high temperature oxidation resistance and friction resistance of titanium alloy greatly reduced. When their working environment contains salt, titanium alloys are subjected to thermal corrosion, which limits their wider practical applications. This paper introduce the aluminide coating and its preparation methods. The characteristics and functional mechanism of three functional coatings for service environment, such as high temperature resistant alumina-based coating, thermal corrosion resistant alumina-based coating and wear-resistant alumina-based coating are summarized. Finally, the development direction of composite coatings of titanium and titanium alloys for complex service environment is prospected.

Background: Aluminum phosphide (AlP), also known as “rice tablet,” is widely used as an effective pesticide. However, AlP poisoning is a common cause of mortality in many countries, such as Iran. Unfortunately, there is no specific antidote for AlP toxicity to date. AlP releases phosphine gas when it is exposed to moisture and acid. Phosphine is a robust mitochondrial toxin that could significantly inhibit cellular energy metabolism. AlP poisoning is an emergency condition that needs instant and effective intervention. Dihydroxyacetone (DHA) is a simple saccharide used for several pharmacological as well as cosmetic purposes. Previously, we found that DHA could significantly prevent mitochondrial impairment induced by toxic agents such as cyanide and phosphine in various in vitro and in vivo experimental models.Methods: Hospitalized patients (n = 111) were evaluated for eligibility criteria. Among these patients, n = 35 cases were excluded due to incomplete data (n = 11) and suspicion of poisoning rather than AlP (n = 24). Meanwhile, n = 76 cases with confirmed AlP poisoning were included in the study. AlP-poisoned patients who did not receive DHA (n =18) were used as the control group.Patients (n = 58) received at least one dose of DHA (500 ml of 5% DHA solution w/v, i.v.) in addition to routine treatment of AlP poisoning. Arterial blood gas (ABG), blood pH, bicarbonate levels, and other vital signs and biochemical measurements were monitored. Moreover, the mortality rate and time of hospitalization were evaluated in both DHA-treated (n = 58) and AlP-poisoned patients without DHA administration (n = 18). Several biomarkers were assessed before (upon hospitalization) and after DHA treatment. The routine tests for AlP-poisoned patients in this study were the measurement of electrolytes (K+ and Na+), WBC, RBC, hemoglobin, INR, carbonate (HCO3), blood pH, PaCO2, and PaO2 and SGPT, SGOT, BUN, Cr. Results: Upon patients' admission, significant decreases in blood pH (acidosis), blood PaO₂, and HCO₃ levels were the hallmarks of AlP poisoning. It was found that DHA significantly alleviated biomarkers of AlP poisoning and tremendously enhanced patients’ survival rate compared to patients treated based on hospital routine AlP poisoning protocols (no DHA). No significant adverse effects were evident in DHA-treated patients in the current study.Interpretation: These data suggest that parenteral DHA is a novel and effective antidote against AlP poisoning.Trial registration: IR.SUMS.REC.1394.102

Since the first generation of 7xxx superhard aluminum alloy was investigated in 1930, hitherto the fifth generation aluminum alloy materials with high comprehensive properties such as high static strength, high strength, heat resistance, high toughness, damage resistance, low density and low quenching sensitivity have been improved and developed. This paper reviews the progress of 7xxx aluminum alloy materials in composition, microstructure, properties, preparation methods, heat treatment strengthening and applications from 2014 to 2021. The effect of adding trace elements on microstructure and properties of 7xxx series alloy and the problems existing in aging precipitation characteristics and reinforcement mechanism are discussed. The future development direction of 7xxx superhard aluminum alloy is prospected by optimizing heat treatment technological, adding appropriate trace elements to alloy and controlling alloy microstructure.

The current study emphasizes on optimizing a suitable ratio of enzymatically hydrolyzed potato powder (EHPP) and whole milk powder (WMP) to produce a quality yogurt by evaluating the physicochemical and rheological properties. The results showed that the addition of EHPP decreased the pH towards acidic conditions which resulted in the high acidity of yoghurt. The proximate composition showed that EHPP increased the ash, protein, water holding capacity (WHC) while fat, synersis, color parameters and total solid were decreased when compared to control yoghurt (CY) sample. Moreover, texture profile (TPA) analysis showed that the addition of EHPP decreased the hardness and cohesiveness while springiness did not show significant difference. Furthermore, rheological properties revealed that EHPP decreased the storage modulus (G’) and loss modulus (G”) when compared with control. In addition to this, sensory analysis revealed that the treatment P4M (1:3) was found as optimum ratio regarding taste, flavor, and aroma. Besides this, scanning electron microscopy (SEM) confirms that the high amount of EHPP resulted in the void holes while CY showed dense gel structure. The prepared yogurt with EHPP provides an excellent flavor, satisfying sweetness and homogeneous texture. These findings suggest the optimum formulation ratio of prepared yogurt was found to be P4M (1:3) for desirable attributes and consumer acceptance. The prepared yogurt from the EHPP presents the potential industrial applications.

The purpose of this work was analysing the compaction of a cohesive material using different DEM simulators to determine the equivalent contact models and identify how some parameters of the simulations affect the compaction results (maximum force and compacts appearance) and computational costs. For that purpose, three cohesion contact models were tested (‘linear cohesion’ in EDEM; ‘SJKR’ and ‘SJKR2’ in LIGGGHTS). The influence of the particle size distribution (PSD) on the results was also investigated. Further assessments were performed on the effect of selecting different timesteps, using distinct conversion tolerances for exporting the 3D models to STL files and moving the punch with different speeds. Consequently, it was possible to determine that a timestep equal to a 10% Rayleigh timestep, a conversion tolerance of 0.01 mm and a punch speed of 0.2 m/s are adequate for simulating the compaction process using the contact models in this work. In addition, the results determined that the maximum force was influenced by the PSD because of the rearrangement of the particles. The PSD was also related to the computational cost because of the number of simulated particles and their sizes. Finally, an equivalence was found between the linear cohesion and SJKR2 contact models

Nano medicine seeks to deliver a valuable set of research tools and clinically useful devices in the near future. The current medical field is in dire need of new commercial applications in the pharmaceutical industry that may include advanced drug delivery systems, new therapies, and in vivo imaging. Here in this experimental study, the nano materials used in DNA biosensors like silver nano dots were incorporated as nano biosensors are used for both therapeutic and diagnostic applications. The most important step while preparing a DNA biosensor is the immobilization of DNA probe on the surface of a sensing device such as an electrode. The amount of immobilized DNA probe will influence the accuracy sensitivity, selectivity and life of a DNA biosensor directly. Because of the high surface to volume ratio and excellent biological compatibility, nano materials can enlarge the sensing surface area to increase the amount of immobilized DNA and the DNA mixed with nano materials can keep its biologically activity well.In this study,silver nano dots created in our lab were functionalized with thio nucleides and were used as nano sensor probes in bio bar code assays.

Powder Bed Fusion (PBF) is a type of Additive Manufacturing (AM) technology that builds parts in a layer-by-layer fashion out of a bed of metal powder via the selective melting action of a laser or electron beam heat source. The technology has become widespread, however the demand is growing for closed loop process monitoring and control in PBF systems to replace the open loop architectures that exist today. This paper demonstrates the simulated efficacy of applying closed-loop state estimation to the problem of monitoring temperature fields within parts during the PBF build process. A simplified LTI model of PBF thermal physics with the properties of stability, controllability and observability is presented. An Ensemble Kalman Filter is applied to the model. The accuracy of this filters’ predictions are assessed in simulation studies of the temperature evolution of various test parts when subjected to simulated laser heat input. The significant result of this study is that the filter supplied predictions that were about 2.5x more accurate than the open loop model in these simulation studies.

Cellular substructure has been widely observed in the sample fabricated by laser powder bed fusion, while its growth direction and the crystallographic orientation have seldom been studied. This research tries to build a general model to construct the substructure from its two-dimensional morphology. All the three Bunge Euler angles to specify a unique growth direction are determined, and the crystallographic orientation corresponding to the growth direction is also obtained. Based on the crystallographic orientation, the substructure in the single track of austenitic stainless steel 316L is distinguished between the cell-like dendrite and the cell. It is found that, with the increase of scanning velocity, the substructure transits from cell-like dendrite to cell. When the power is 200 W, the critical growth rate of the transition in the single track can be around 0.31 ms^-1.

A combination of Poloxamer 407 (P407) and hydroxypropyl methylcellulose (HPMC) hydrosols is proposed as an in situ thermo-gelling vehicle for the nasal drug delivery of chlorhexidine-silver nanoparticles conjugates (SN-CX). Varying ratios of P407 and HPMC were applied in the presence and absence of SN-CX in order to optimize the gelation temperature (Tg) to values close to the physiological nasal such (30–34°C). Mechanisms for the observed gelation phenomena were suggested based on viscosimetry, texture analysis, and dynamic light scattering. Tests were carried out for sprayability, washout time, in vitro drug release, ex vivo permeation, and antimicrobial activity. When applied separately, HPMC was found to lower the P407 gelation temperature, whereas SN-CX increased it. However, in the presence of HPMC, SN-CX interfered with the P407 micellar organization in a principally contrasting way, while leading to an even further decrease in Tg. SN-CX-loaded nasal formulation composed of P407 16% and HPMC 0.1% demonstrated a desired gelation at 31.9 °C, good sprayability (52.95% coverage of the anterior nasal cavity), mucoadhesion for 70 min under simulated nasal clearance, expedient release and permeation, and preserved anti-infective activity against seasonal Influenza virus and beta-coronavirus, Pseudomonas aeruginosa, Klebsiella pneumoniae, Staphylococcus aureus and other pathogens. Our findings suggest that the current development could be considered a potential formulation of a protective nasal spray against respiratory infections.

The chelating aluminum complex [2-(Me2NCH2)C2B10H10]AlX2 (X = Br 3, CH3 4) was synthesized using 2-dimethylaminomethyl-o-carboranyl lithium (2) with aluminum tribromide or dimethylaluminum bromide, resulting in a modest yield. Compound 4 was obtained by reacting compound 3 with CH3Li in toluene. All compounds were characterized by infrared (IR) spectroscopy, 1H, 11B, 13C nuclear magnetic resonance (NMR) spectroscopy, and X-ray crystallography. X-ray structural studies of CabNAlBr2 (3) and CabNAlMe2 (4) indicated that the Al atom was located at the center of a distorted tetrahedron. Crystal structures of the CabNAlBr2 (3) [a = 8.9360(3) Å, b = 12.0358(9) Å, c = 14.7730(4) Å, α = β = γ = 90°] and the CabNAlMe2 (4) [a = 8.9551(3) Å, b = 11.9126(9) Å, c = 14.7711(4) Å, α = β = γ = 90°] were obtained. The reactivity of aluminum complexes 3 and 4 with Lewis bases, such as H2O, pyridine, alkylamines, and arylamines, confirmed their rapid decomposition.

Iron supplementation is associated with side effects and thus reduces the intake compliance. Because it has fewer side effects, a recent trial recommended low-iron micronutrient powder (MNP) for the prevention of anemia in Bangladeshi children exposed to a high concentration of iron from drinking groundwater. In the present study, we hypothesize that the low-iron MNP is a potential intervention to prevent childhood anemia in the low groundwater-iron settings in Bangladesh. A cross-sectional study was conducted in Bangladesh with children aged 2-5 years who drank groundwater containing a low level of iron (0-&lt;2 mg/L).The combined intake of iron was calculated from the key sources--diet, groundwater and MNPs. The intakes of iron were compared against the standard reference intake. The children’s hemoglobin was measured using a photometer. Combined intake of iron from dietary, groundwater and low-iron MNP in children was 5.8±2.0 and 6.9±2.5 mg/day comprising 193% and 169% of the Estimated Average Requirement in the 2-3 year-old and 4-5 year-old subgroups, respectively. Combined intake of bioavailable iron from dietary and groundwater sources was 0.42±0.023 and 0.22±0.019 mg/day in children exposed to groundwater concentration 0.8-&lt;2.0 mg/L and 0.0-&lt;0.8 mg/L respectively (p&lt;0.001). The mean concentration of hemoglobin in the respective groups was 12.17±0.94 mg/dl and 11.91±0.91 mg/dl (p=0.30). The combined intake of iron from dietary and groundwater sources was associated with maintenance of hemoglobin concentration at the non-anemic level in most of the children. The finding highlights the potential of low-iron MNP in controlling childhood anemia in this setting.

Introduction: Among the many factors that may limit effective wound healing in patients with chronic ulcers, bacterial infection and poor cell recruitment are primary causes that contribute to prolonged healing. Thus, a novel strategy that aims to prevent bacterial infection within the wound, while at the same time providing structural scaffolding that promotes endogenous tissue repair, would be of great interest. Here, we developed a thermo-sensitive silver nanoparticle hydrogel composite as an antibacterial nutritional scaffold for the wound that contains all nutrients required for cell growth while preventing bacterial infection with the ability to fill up all the cavities and void areas in wounds regardless of their geometry. Methods: Silver nanoparticles (AgNPs) were synthesized by chemical reduction. After characterization, silver hydrogel nanocomposite was developed by reconstitution of collagen-based hydrogel powder in a nanoparticle suspension of varying AgNPs concentrations (200, 400, and 600 ppm). The antibacterial activity of the formulations was examined in vitro and in vivo in subcutaneous implant infected model. The wound healing efficacy of the hydrogel nanocomposite was also evaluated using a splinted wound model in rats through comparison of clinical wound measurements and histological assessments. Cytocompatibility assay and biochemical analysis of blood at the end of in vivo wound healing study were performed to evaluate the safety of formulations. Results: The synthesized nanoparticles were spherical and stable. While hydrogel alone did not show any bacterial reduction in vitro, the inhibition of bacterial growth was significant in all silver hydrogel nanocomposites compared to controls (p <0.05) and was dose-dependent, with maximum reduction observed in the 600 ppm group (4.56±0.26 LOG CFU/mL, P<0.001). All concentrations of AgNPs hydrogel composites showed significant antibacterial activity in vivo as well (P<0.0001). Treatment of splinted wounds with AgNPs hydrogel composite resulted in faster wound closure and accelerated wound re-epithelialization. The formulations were non-cytotoxic and did not differ significantly in hematological and biochemical factors from the control group in in vivo study. Conclusions: By presenting promising antibacterial and wound healing activity, silver hydrogel nanocomposite offers a safe therapeutic option that can be used as a functional scaffold for an acceleration of wound healing.

Formula feeding, as an alternative to breastfeeding, offers benefits such as convenience and consistent nutrition. Among the drawbacks of formula feeding, however, is potential dilution or concentration errors in the of formula during preparation that may lead to infant health issues. The present study aimed to investigate the accuracy of caregiver measurements as they prepared infant formula under multiple conditions, compared with manufacturer specifications. A diverse sample of caregivers (N = 84) participated in this cross-over experimental study. Participants hand-scooped infant formula powder and poured water to prepare 4oz and 7oz feedings, using both a standardized set of infant formula products and participants’ own products. Linear mixed effects models were used to estimate fixed effects of target amount (4oz versus 7oz) and products (participant versus researcher) on mean absolute percent error (MAPE) of measurement. Across all conditions MAPE was significantly greater for measuring powder than for water (9.0% vs. 4.4%; p&lt;0.001) with a combined powder and water MAPE at 13.0%. Greater measurement error was associated with the odd-sized 7oz preparation and participants’ own products. We observed considerable variability and substantial error during infant formula preparation, particularly for hand-scooping of powder, which tended toward higher values than the theoretical gold standard.

Sodium-potassium (NaK) liquid alloy is a promising candidate for use as anode material in sodium batteries because of its fluidity, which effectively suppresses the growth of sodium or potassium dendrites. However, the poor wettability of the NaK liquid alloy on conventional metal substrates is unfavorable for cell fabrication due to its strong surface tension. In this paper, low-density and low-cost fluorinated aluminum foam is used as a substrate support material for NaK liquid alloy. By combining low surface tension NaK@C with fluorinated aluminum foam, we obtain a uniformly distributed and structurally stable electrode material. The composite electrode has a cycling stability of more than 3000 hours in a symmetrical cell. Furthermore, when coupled with a sulfurized polyacrylonitrile cathode in carbonate electrolyte, it maintains excellent stability even after 800 cycles, with 72% of capacity retention.

Turbulent flow is the first and fundamental physical phenomena to evaluate when optimising cost and reducing emissions from an Anode Baking Furnace (ABF). Gas flow patterns, velocity field, pressure drop, shear stress, and turbulent dissipation rate variables are the main operational parameters to be optimised, considering a specific geometry. Computational Fluid Dynamics (CFD) allows simulating physical phenomena using numerical methods with computer resources. In particular, the finite element method is one of the most used methods to solve the flow equations. This method requires a discretisation of the geometry of the ABF, called mesh. Hence, mesh is the main input to the finite element method. A suitable mesh for applying a discretisation method determines whether the problem can be simulated or not. Generating an appropriate mesh remains a challenge to perform accurate simulations. In this work, a comparison between meshes generated using two mesh generation tools is presented. Results of different study cases are included.

Molybdenum tailings powder (MTs) is an industrial waste that contains more than 85% contents of SiO2, Al2O3, CaO, and Fe2O3. Therefore, MTs has the potential pozzolanic activity and can be used as a mineral admixture in cementitious materials. In order to understand the influence of MTs as an admixture on the cement hydration process, the hydration heat and hydration kinetics of the composite cementitious materials (CCMs) were investigated by an isothermal calorimeter and the Krstulovic-Dabic model. Furthermore, the influences of fly ash (FA), slag (SL) and MTs on hydration heat at the same content were compared and analyzed. Results show that proper amount of MTs can promote the hydration of CCMs. When the content of MTs is not more than 15%, the second exothermic peak of CCMs appears earlier and the peak heat release increases. However, when the content of MTs exceeds 15%, the second exothermic peak of CCMs is delayed and the peak heat release decreases. The cumulative heat release of CCMs gradually decreases with an increasing content of MTs. When the replacement of MTs, FA, and SL is 15% respectively, the addition of MTs enhances the second exothermic peak of CCMs compared to FA and SL. The final heat release of MTs is higher than that of FA, but lower than that of SL. The hydration process of CCMs undergoes three stages: nucleation and crystal growth (NG), interactions at phase boundaries (I), and diffusion (D). The incorporation of MTs shortens the NG stage and I stage.

Powder bed fusion (PBF) process is a metal additive manufacturing process which can build parts with any complexity from a wide range of metallic materials. PBF process research has predominantly focused on the impact of only a few parameters on product properties due to the lack of a systematic approach for optimizing a large set of process parameters simultaneously. The pivotal challenges regarding this process require a quantitative approach for mapping the material properties and process parameters onto the ultimate quality; this will then enable the optimization of those parameters. In this study, we propose a two-phase framework for optimizing the process parameters and developing a predictive model for 316L stainless steel material. We also discuss the correlation between process parameters -- i.e., laser specifications -- and mechanical properties and how to achieve parts with high density (> 98%) as well as better ultimate mechanical properties. In this paper, we introduce and test an innovative approach for developing AM predictive models, with a relatively low error percentage of 10.236% that are used to optimize process parameters in accordance with user or manufacturer requirements. These models use support vector regression, random forest regression, and neural network techniques. It is shown that the intelligent selection of process parameters using these models can achieve an optimized density of up to 99.31% with uniform microstructure, which improves hardness, impact strength, and other mechanical properties.

Traditionally Moringa is known as mystical miracle tree or the tree of life. Soup can be classified as an appetizer, warm food during cold and sick. Moringa oleifera pods have been procured from College of Agriculture, JNKVV, Jabalpur. The present investigation is planned with objectives to standardize best combination of for the development of instant soup mix, to evaluate various quality parameters, to evaluate the storage stability and cost estimation of product. Protein in instant soup is ranged from 9.76 to 11.89 percent in different formulations of instant soup mix. Formulation MPP4 (11.89) had significantly maximum protein content followed by MPP3, MPP2, MPP1 and Control with the minimum protein content. The original instant soup mix (control) exhibited highest carbohydrate content (61.52%) followed by MPP1, MPP3, MPP4, and MPP2 with lowest content. The evaluated scores of control for colour and appearance, taste, flavour, consistency, after taste and overall acceptability are 8.36, 8.50, 8.60, 8.90, 8.76 and 8.63 respectively

Metal powder bed fusion (PBF) additive manufacturing (AM) builds metal parts layer by layer upon a substrate material. The strength of this interface between substrate and printed material is important to characterize, especially in applications where the substrate is retained and included in the finished part. This paper studied the tensile and torsional strengths of wrought and additively manufactured (through PBF) SS316L and compared them to specimens composed of half wrought material and half PBF material. The PBF specimens consistently exhibited higher strength and lower ductility than the wrought specimens. The hybrid PBF/wrought specimens performed similarly to the wrought material. In no specimens did any failure appear to occur at or near the interface between wrought substrate and PBF material. In addition, most of the deformation in the PBF/wrought specimens appeared to be limited to the wrought portion of the specimens. These results are consistent with microscopy showing smaller grain size in the PBF material, which often leads to increased strength in SS316L due to the Hall-Petch relationship.

The microstructural evolution, thermodynamics and kinetics of Mo-21%Tm₂O₃ (mass fraction, %) powder mixtures during ball milling were investigated using X-ray diffraction and transmission electron microscopy. Ball milling induced Tm₂O₃ to be decomposed and then dissolved into Mo crystal. The supersaturated nanocrystalline solid solution of Mo (Tm, O) was obtained after 96 h of ball milling. The elements of Mo, Tm and O were distributed uniformly in the ball-milled particles. Based on the semi-experimental theory of Miedema, a thermodynamic model was developed to calculate the driving force of phase evolution. There was no chemical driving force to form a crystal solid solution of Tm atoms in Mo crystal or an amorphous phase because the Gibbs free energy for both processes was higher than zero. For Mo-21%Tm₂O₃, it was mechanical work, not negative heat of mixing, that provided the driving force to form supersaturated nanocrystalline Mo (Tm, O) solid solution.

This paper reports the effect of silicon substrate orientation and aluminum nitride buffer layer deposited by molecular beam epitaxy on the growth of aluminum nitride thin films deposited by DC magnetron sputtering technique at low temperature. The structural analysis has revealed a strong (0001) fiber texture for both substrates Si (100) and (111) and a hetero-epitaxial growth on few nanometers AlN buffer layer grown by MBE on Si (111) substrate. SEM images and XRD characterization have shown an enhancement in AlN crystallinity thanks to AlN (MBE) buffer layer. Raman spectroscopy indicated that the AlN film was relaxed when it deposited on Si (111), in compression on Si (100) and under tension on AlN buffer layer grown by MBE/Si (111) substrates, respectively. The interface between Si (111) and AlN grown by MBE is abrupt and well defined; contrary to the interface between AlN deposited using PVD and AlN grown by MBE. Nevertheless, AlN hetero-epitaxial growth was obtained at low temperature (<250°C).

Aluminum, a contentious trace element found in the environment, has been demonstrated to have harmful effects on both humans and animals. In contrast, Sempervivum tectorum, an evergreen plant, has been found to offer numerous beneficial effects for both humans and animals. Therefore, this study aims to assess the protective effect of S. tectorum on certain reproductive biomarkers in male rats exposed to aluminum. Thirty-five Wistar rats were randomly divided into five groups: NTC (no-treatment control) received distilled water; NC (negative control) received drinking water containing 1 mg/L aluminum sulfate (AS); E1 received 1 mg/L AS along with an 8% S. tectorum extract; PC (positive control) received only 8% S. tectorum extract; E2 received 1 mg/L AS for three months followed by 8% extract for one month. The study analyzed testosterone, LH, FSH, body weight, and the histological structure of the testis, epididymis, and prostate, as well as the levels of zinc, manganese, copper, and iron in these organs. Significant decreases in body weight, testis, and epididymis size were observed in the aluminum-exposed groups compared to the control, whereas these decreases were not significant in the S. tectorum-treated groups compared to the control. Aluminum exposure led to significant decreases in testosterone and LH levels, with FSH levels showing a non-significant decrease in males, which were mitigated significantly by the administration of the plant extract. Histological analysis revealed alterations in the testis, epididymis, and prostate of the AS-exposed groups, including necrosis of seminiferous tubule epithelium and Leydig cells in the testis, and basal epithelial necrosis in the epididymis and prostate. Aluminum levels increased in all organs studied, while levels of zinc, copper, iron, and manganese decreased, showing a negative and significant correlation with aluminum levels. The aqueous extract of S. tectorum demonstrated a protective effect on certain studied biomarkers in male rats affected by aluminum exposure.