In this work, a xylan-based antimicrobial additive agent was prepared and aimed for uses in paper products against Escherichia coli bacteria. The derived Cationic-Xylan-grafted-PHGH (CX-g-PHGH) was successfully synthesized by graft copolymerization of cationic-xylan with guanidine polymer (PHGH) using ceric ammonium nitrate as initiator. The obtained CX-g-PHGH had maximum PHGH grafting ratio of 18.45% and efficiency of 58.45%, and showed good viscosity and thermal stability. Furthermore, the paper samples prepared in this work were reinforced obviously with the addition of CX-g-PHGH by improved mechanical properties. Compared to the reference paper without any of the xylan-derivatives, the index of tensile, tear, burst and folding endurance of the paper had increases up to 20.07%, 25.31%, 30.20% and 77.78%, respectively. Moreover, the prepared CX-g-PHGH paper exhibited an efficient antimicrobial activity against E. coli bacterial, by which a lot of applications based on the new xylan-derived additive agent obtained in this work could be found, especially in field of antimicrobial paper products against E. Coli bacteria from contaminated food.

The mechanism of ciprofloxacin action involves interference with transcription and replication of bacterial DNA, which results in elevated oxidative stress, and bacterial cell death. Vorinostat was shown to induce oxidative DNA damage. In the current work, the possibility for interactive effect of vorinotat on ciprofloxacin-induced cytotoxicity against a number of reference bacteria was investigated. Standard bacterial strains were Escherichia coli ATCC 35218, Staphylococcus aureus ATCC29213, Pseudomonas aeruginosa ATCC 9027, Staphylococcus epidermidis ATCC 12228, Acinetobacter baumannii ATCC 17978, Proteus mirabilis ATCC 12459, Klebsiella pneumoniae ATCC 13883, methicillin-resistant Staphylococcus aureus (MRSA) (ATCC 43300), and Streptococcus pneumoniae (ATCC 25923). The antibacterial activity of ciprofloxacin with or without pretreatment of bacterial cells by vorinostat was examined using disc diffusion procedure and determination of the minimum inhibitory concentration (MIC) and zones of inhibition of bacterial growth. All tested bacterial strains showed sensitivity to ciprofloxacin. When pretreated with vorinostat, significantly larger zones of inhibition and smaller MIC values were observed in all bacterial strains compared ciprofloxacin alone. As a conclusion, current results showed the possible agonistic properties for vorinostat when it is used together with ciprofloxacin. Future research will be focus on molecular mechanisms possible for such interactive effect.

This study aimed to evaluate the effects of a palygorskite-based antibacterial agent (PAA) as an alternative to antibiotics on growth performance, blood parameters, rumen fermentation, and rumen microbiota in sheep. A total of 120 sheep were randomly divided into five groups of six replicates with four sheep each. Sheep were fed a basal diet, an antibiotic diet supplemented with 500 g/t chlortetracycline (CTC), and a basal diet supplemented with 500, 1,000, and 2,000 g/t PAA for 80 d, respectively. Supplementation with 2,000 g/t PAA and 500 g/t CTC increased the average daily gain (ADG) of sheep compared with the control group (P < 0.05). Diets supplemented with 2,000 g/t PAA and 500 g/t CTC reduced (P < 0.05) the feed: gain (F/G ratio) in the overall periods. Dietary Supplementation with 1,000 g/t PAA significantly increased albumin and total protein (P < 0.05). A significant positive correlation was found between growth hormone concentration and PAA supplementation (P < 0.05). In addition, compared to the control group, the CTC group had higher growth hormone concentration and lower lipopolysaccharide concentration (P < 0.05). No dif-ference was observed between the five groups in terms of rumen fermentation characteristics (P > 0.05). At the phylum level, the relative abundance of Proteobacteria was lower in the PAA 2000 and CTC 500 groups than that in the control and PAA 500 groups (P < 0.05). At the genus level, a sig-nificant decrease (P < 0.05) in the relative abundance of RuminococcaceaeUCG-010 was observed in the PAA 1000, PAA 2000, and CTC 500 groups compared with that in the control group. In addition, the relative abundance of Prevotella1 (P < 0.05) was higher in the PAA 2000 group than that in the control group. These findings indicate that dietary supplementation with PAA has ameliorative effects on growth performance, blood parameters, and rumen microbiota, with an optimal dosage of 2,000 g/t for sheep.

Ti and its alloys are the most commonly used materials for biomedical applications. However, bacterial infection after implant placement is still one of the significant rising complications. Therefore, the application of the antimicrobial agents into implant surfaces to prevent implant-associated infection has attracted lots of attention. Scientific papers have shown that inorganic antibacterial metal element (e.g. Ag, Cu, Zn) can be introduced to implant surfaces with the addition of metal nanoparticles or metallic compounds into electrolyte via micro-arc oxidation (MAO) technology. In this review, the effects of the composition and concentration of electrolyte and process parameters (e.g. voltage, current density, oxidation time) on morphological characteristics (e.g. surface morphology, bonding strength), antibacterial ability and biocompatibility of MAO antimicrobial coating were discussed in detail. Anti-infection and osseo-integration can be simultaneously accomplished with the selection of the proper antibacterial elements and operating parameters. Besides, MAO assisted by magnetron sputtering (MS) to endow Ti-based implant materials with superior antibacterial ability and biocompatibility was also discussed. Finally, the development trend of MAO technology in the future was forecasted.

Recent years have witnessed significant advances in reinforcement learning (RL), which has registered remarkable success in solving various sequential decision-making problems in machine learning. Most of the successful RL applications, e.g., the games of Go and Poker, robotics, and autonomous driving, involve the participation of more than one single agent, which naturally fall into the realm of multi-agent RL (MARL), a domain with a relatively long history, and has recently re-emerged due to advances in single-agent RL techniques. Although, typically, the communication protocol between agents is manually specified and not altered during training, recently, some papers have shown signs of trying to emerge a communication between agents on the one hand and, on the other hand, to understand what is exchanged between agents. So, there is a growing body of literature on this topic which includes qualitative and quantitative studies and the ones that apply mixed methods. This study presents the scoping review of the methodological strategies undertaken in a total of 16 research articles. The results present the critical appraisal of quantitative methods in terms of validity and reliability and for qualitative methods considering four trustworthiness factors. In the end, relevant insights are further explored with implications and reflections on how they can benefit one's research in the field.

Lyme disease, the leading vector-borne ailment in the U.S., annually affects an estimated 476,000 individuals, predominantly in the Northeast and Upper Midwest. Despite its increasing incidence, the evaluation of risk within U.S. cities, including natural public lands, remains inadequate. This study focuses on blacklegged tick occurrences and Borrelia burgdorferi infection prevalence in 24 Staten Island parks, aiming to assess Lyme disease exposure risk. Monthly acarological risk index (ARI) calculations from 2019 to 2022 revealed elevated values (0.16-0.53) in specific parks, notably Wolfe’s Pond Park, High Rock Park, Clay Pit Pond Park, Clove Lake Park, and Fair View Park. June (0.36) and November (0.21) consistently exhibited heightened ARIs, aligning with peak tick collection months. Despite stable yearly infection rates at 28.97%, tick densities varied significantly between parks and years. Identifying a high transmission risk in specific parks in Staten Island, a highly urbanized part of New York City, emphasizes the continuous necessity for Lyme disease risk management, even within the greenspaces of large cities.

This paper presents an innovative multi-agent, data-driven reinforcement learning (RL) approach to develop and utilize the thermal equivalent network model that represents the motor's thermal dynamics. A multi-agent reinforcement learning is designed and trained to adjust the model parameters using data from several motor driving cycles. To ensure the incoming driving cycle matches the historical data before employing the pre-trained RL agents, offline statistical analysis and clustering techniques are developed and used. Numerical simulations highlighted the RL agent's ability to develop strategies that effectively address the variability of driving cycles. The proposed RL framework showed its capability to accurately reflect the motor's thermal behavior under various driving conditions.

System-of-systems (SoS) evolution is a complex and unpredictable process. Although various principles to facilitate collaborative SoS evolution have been proposed, there is a lack of experimental data validating their effectiveness. To address these issues, we present an Agent-Based Model (ABM) for SoS evolution in the Internet of Vehicles (IoV) , serving as a quantitative analysis tool for SoS research. By integrating multiple complex and rational behaviors of individuals, we aim to simulate real-world scenarios as accurately as possible. To simulate the SoS evolution process, our model employs multiple agents with autonomous interactions and incorporates external environmental variables. Furthermore, we propose three evaluation metrics: evolutionary time, degree of variation, and evolutionary cost, to assess the performance of SoS evolution. Our study demonstrates that enhanced information transparency significantly improves the evolutionary performance of distributed SoS. Conversely, the adoption of uniform standards only brings limited performance enhancement to distributed SoSs. Although our proposed model has limitations, it stands out from other approaches that utilize Agent-Based Modeling to analyze SoS theories. Our model focuses on realistic problem contexts and simulates realistic interaction behaviors. This study enhances the comprehension of SoS evolution processes and provides valuable insights for the formulation of effective evolutionary strategies.

The aim of this study was to investigate the physicochemical characterization and biological activities of chitosan (CH) based composite films with the incorporation of chestnut flower essential oil (CFEO). The composite films were prepared by casting method and characterized in terms of structural, morphological and mechanical properties via FT-IR, XRD, UV, SEM and TGA. The results proved the significantly increased water vapor permeability (WVP), heat resistance, antibacterial and antioxidant capabilities of CH-CFEO films. The incorporation of CH and CFEO enhanced the UV blocking, which made the film shield almost all UV light. Films with the tensile strength of 6.37 ± 0.41 MPa and elongation at break of 22.57 ± 0.35% were got with 6 mg mL-1 CFEO. Subsequently, the fruit preservation experiments also confirmed that the composite films could effectively extend the shelf life of bananas through their excellent water vapor and oxygen barrier. These desirable performances enable our newly developed composite films to be a remarkable packaging material to solve the fresh fruit preservation dilemma.

Observe the synergistic effect and dose-effect relationship of Trimethoprim (TMP) on bactericidal activity with Flos Lonicerae in vitro. Microamount chessboard dilution method was conducted to determine the minimal inhibitory concentration (MIC) of Trimethoprim, Flos Lonicerae, as well as the combination of Trimethoprim and Flos Lonicerae separately against Staphylococcus aureus, Escherichia coli in vitro and Salmonella. The pour plate count method was used to determine the combined bactericidal activity of Flos Lonicerae combined with Different concentrations TMP. The results showed that the MIC values of the combination of Flos Lonicerae with TMP was much less than the MIC values of the independent use of Flos Lonicerae or TMP, The FIC values of the combination of Flos Lonicerae with TMP were between 0.5 and 1, there was additive effect between them. The bactericidal rates were fitted with least square method, the 95% confidence intervals of the optimal blending quantity about the combination of Flos Lonicerae with TMP on the test organisms were 231μg·mL^-1-249μg·mL^-1, 237μg·mL^-1-259μg·mL^-1, and 235 -259μg·mL^-1

Berberis vulgaris L. (Berberidaceae) is a shrub that has been widely used in European folk medicine as an anti-inflammatory and antimicrobial agent. The purpose of our study was to elucidate the mechanisms of antiproliferative action of the plant’s methanolic root extract (BVR) against colon cancer cells. Cytotoxicity and pro-apoptotic activity were determined in human colon adenocarcinoma cell lines (LS180 and HT-29) and control colon epithelial CCD841 CoN cells. According to the MTT assay, after 48 h of cell exposure, the IC50 values were as follows: 4.3; 46.1 and 50.2 µg/mL for LS180, HT-29, and CCD841 CoN cells, respectively, showing the greater sensitivity of cancer cells to BVR. The Cell Death Detection ELISAPLUS kit demonstrated that BVR induced programmed cell death only against HT-29 cells. RT-qPCR with relative quantification method showed significant changes in the expression of genes related to apoptosis in both colon cancer cell lines. The genes BCL2L1 (126.84-366.66%), BCL2L2 (277.08-330.12%), CASP3 (180.36-261.36%) and CASP9 (158.08-213.46%) had significantly elevated expression, while BCL2 (23.08-52.06%) had reduced expression. Furthermore, in a panel of antioxidant tests, BVR showed positive effects (63.93±0.01, 122.92±0.01, and 220.29±0.02 mg Trolox equivalents (TE)/g in the DPPH•, ABTS•+ and ORAC assays, respectively). In the lipoxygenase (LOX) inhibition test, BVR revealed 62,60±0.87% of enzyme inhibition. The chemical composition of BVR was determined using UHPLC-UV-CAD-MS/MS analysis and confirmed the presence of several known alkaloids, including berberine, as well as other alkaloids and two derivatives of hydroxycinnamic acid (ferulic and sinapic acid hexosides). This is the first such extensive assessment of the biological activity of BVR. The results are very promising and encourage for the use of BVR as a comprehensive chemopreventive agent (anti-inflammatory, antioxidant, and pro-apoptotic) in colorectal cancer.

Bovine respiratory disease (BRD) is the leading cause of morbidity and mortality in cattle raised in North America. At the feedlot, cattle are subject to metaphylactic treatment with macrolides to prevent BRD, a practice that may promote antimicrobial resistance and has resulted in an urgent need for novel strategies. Mannheimia haemolytica is one of the major bacterial agents of BRD. The inhibitory effects of two amphipathic, α-helical (PRW4, WRL3) and one β-sheet (WK2) antimicrobial peptides were evaluated against multidrug-resistant (MDR) M. haemolytica isolated from Alberta feedlots. WK2 was not cytotoxic against bovine turbinate (BT) cells by the MTT (3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyltetrazolium bromide) assay. All three peptides inhibited M. haemolytica, with WK2, being the most efficacious against multiple isolates. At 8-16 µg/ml, WK2 was bactericidal against Mh 330 in broth and at 32 µg/ml in the presence of BT cells, reduced the population by 3 logs CFU/ml without causing cytotoxic effects. The membrane integrity of Mh 330 was examined using NPN (1-N-phenylnaphthylamine), and ONPG (o-Nitrophenyl β-D-galactopyranoside) with both the inner and outer membranes being compromised. Thus, WK2 may be a viable alternative to the use of macrolides as part of BRD prevention and treatment strategies.

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Management of chronic inflammation and wounds has always been a key issue in the pharmaceutical and healthcare sector. Curcumin (CCM) is an active ingredient extracted from turmeric rhizomes that has antioxidant, anti-inflammatory, and antibacterial activities, thus showing significant effectiveness toward wound healing. However, its shortcomings such as poor water solubility, poor chemical stability and fast metabolic rate limit its bioavailability and long-term use. In this context, hydrogels appear to be a versatile matrix for carrying and stabilizing drugs due to the biomimetic structure, soft porous microarchitecture, and pleasant biomechanical properties. The drug loading/releasing efficiencies can also be controlled by use of highly crystalline and porous metal organic frameworks (MOFs). Here, a flexible hydrogel composed of sodium alginate (SA) matrix and CCM-loaded MOFs was constructed for long-term drug release and antibacterial activity. The morphology and physicochemical properties of composite hydrogels were analyzed by scanning electron microscopy (SEM), Fourier transform infrared spectroscopy (FT-IR), X-ray diffraction (XRD), ultraviolet visible spectroscopy (UV-Vis), Raman spectroscopy and mechanical property tests. The results showed that the composite hydrogel was highly twistable and bendable to mechanically comply with human skin. The as-prepared hydrogel could capture efficient CCM for slow drug release as well as effective killing of bacteria. Therefore, such composite hydrogel is expected to provide a new management system for chronic wound dressings.

Antibacterial bone cements (ABCs), such as antibiotic-loaded bone cements (ALBCs), have been widely utilized in clinical treatments. Currently, bone cements loaded with vancomycin, gentamicin, tobramycin, or clindamycin are approved by the US Food and Drug Administration. However, traditional ALBCs exhibit drawbacks like burst release and bacterial resistance. Therefore, there is a demand for the development of antibacterial bone cements containing novel agents. In this review, we summarize the latest advancements in ABCs. More importantly, we provide an overview and outlook on novel antibacterial agent-loaded bone cements, including metallic antibacterial agents, pH-switchable antibacterial agents, cationic polymers, N-halamines, non-leaching acrylic monomers, antimicrobial peptides, etc. Offering novel perspectives for designing ABCs and treating bone infections.

The antimicrobial quantitative structure–activity relationship of plant flavonoids against Gram-positive bacteria was established in our previous works, and the cell membrane was confirmed as a major site of action. To investigate whether plant flavonoids have similar antibacterial effects and mechanisms against both Gram-negative and Gram-positive bacteria, here, the minimum inhibitory concentrations (MICs) of 37 plant flavonoids against Escherichia coli were determined using the microdilution broth method, and then the correlation between their lipophilic parameter ACD/LogP or LogD_7.40 value and their MIC was analyzed. Simultaneously, the correlation between the ACD/LogP or LogD_7.40 value and the MIC of 46 plant flavonoids reported in literature against E. coli was also analyzed. Both sets of results showed that there is a significant correlation between the LogP value and the MIC of plant flavonoids against Gram-negative bacteria. However, it is difficult to effectively predict the MIC of plant flavonoids against Gram-negative bacteria from their lipophilic parameters. By comparing two regression curves derived from plant flavonoids against Gram-negative and Gram-positive bacteria, it was further discovered that the antibacterial activities of most plant flavonoids against Gram-negative bacteria are stronger than those against Gram-positive bacteria when their LogP values are less than about 3.0, but the opposite is true when their LogP values are more than about 3.6. Moreover, this comparison also suggests that unlike mainly acting on the cell membrane of Gram-positive bacteria, plant flavonoids have multiple mechanisms against Gram-negative species, while the cell membrane is also an important action site among them. Combined with the correlation analyses between the enzyme inhibitory activity and the LogP value of the reported flavonoids, it was further suggested that DNA gyrase is another important target of plant flavonoids against Gram-negative bacteria.

The microbial contamination in food packaging have been a major concern that paved the way for the search for natural based new anti-microbial agents, such as modified α-mangostin. In the present work, twelve synthetic analogs were obtained via semi-synthetic modification of α-mangostin by Ritter reaction, reduction by palladium-carbon (Pd-C), alkylation, and acetylation. The evaluation of the anti-microbial potential of the synthetic analogs showed higher therapeutic value than the parent molecule. The anti-microbial studies proved that I E showed higher antibacterial activity whereas I I showed most significant antifungal activity. Due to their microbial properties, modified α-mangostin can be utilized as active anti-microbial agents in food packaging.

Cadmium Sulfide nanoparticle (CdS-LA hybrid nanoparticles) was synthesized here by a green approach using the precursor cadmium acetate and sodium sulphide along with the extract of a plant Lathyrus aphaca L. containing the phytochemicals which were responsible for surface modification of nanoparticles. The nanoparticle was used to evaluate their inhibition potential against species of bacteria and fungi. The nanoparticles were characterized by XRD which demonstrates the hexagonal crystal structure. SEM confirms the homogenous surface appearance of the CdS-LA hybrid crystalline structure. EDX analysis confirms surface modification of nanoparticles by phytochemicals. FTIR confirmed the Cd-S linkage laterally with the related functional groups and the presence of metabolites on the surface of nanoparticles. The UV-visible spectroscopy confirmed the peak at the characteristic wavelength range but a slight shift occurred in the peak of the CdS nanoparticles due to the presence of the phytochemicals. This study particularly provides an environment-friendly strategy to synthesize the CdS nanoparticles capped by Lathyrus Aphaca L. extract that are biologically active due to the mediation of the plant extract. CdS-LA hybrid nanoparticles have shown inhibition potential against various species of bacteria and fungi and realize the biological importance of the green synthesis of nanoparticles especially mediated with the plant extract.

Antimicrobial resistance (AMR) is a growing public health issue worldwide that affects the world economy. The concern associated with this issue increased during the COVID-19 pandemic. The misuse of antibiotics during the COVID-19 pandemic will have catastrophic implications for the control of AMR. In 2019, the coronavirus illness COVID-19 first appeared in China. COVID-19 infection is a surface-to-surface communicable disease. It is considered the most vital global health disaster of the century. It has rapidly spread around the world and is the greatest challenge for humankind. This chapter discusses the origin, symptoms, transmission, treatment, and recommendations of the COVID-19 disease.

Over the years, chitosan has been the subject of numerous studies and has gained significant popularity as a biomaterial due to its various characteristics, including biocompatibility, biodegradability, and bioactivity. In this work, chitosan fibres surface was modified with ursolic acid to improve their antibacterial properties by wet impregnation method. Five specimens of chitosan fibres were immersed in ursolic acid (UA) solution for varying immersion times of 1, 2, 4, 6, and 8 hours. Characterization was carried out by means of FTIR, SEM, UV-Vis spectroscopy; the results indicated an ongoing chemical reaction between chitosan and ursolic acid resulting in changes to the chemical structure. After 2 hours, the absorbance ratio remained constant; suggesting that the reaction had reached completion and the chemical structure of the sample remained stable. Antibacterial tests were performed on the resulting chitosan fibres against two bacterial strains. The fibres without ursolic acid did not exhibit any noteworthy antibacterial activity against either strain. However, the chitosan fibres modified with ursolic acid showed significant and almost strong antibacterial activity against the Gram-positive strain, S. aureus. These results suggest that chitosan fibres modified with ursolic acid could have potential applications as antibacterial materials, particularly against Gram-positive bacteria.

In the field of modeling social systems, the use of agent-based models (AM) has become a powerful tool for understanding processes occurring in society, in particular, for studying the spread of infections among the population. The agent model is based on a synthetic population consisting of agents, their interactions and sometimes the territory in which the interaction occurs. The choice of an appropriate method for creating such artificial populations and the selection of parameters becomes a key issue affecting the realism of the model and its ability to reflect real-world scenarios. This article delves into the interplay between agent-based modeling, synthetic population construction, and parameter selection, offering our insight into the complex process of modeling infectious disease dynamics. The review concludes with an exploration of extending the Covasim model [1] to experiments in computational epidemiology. Covasim, a dynamic transmission modeling tool, is known for its ability to adapt to different scenarios and offers predictive information critical for managing epidemiological situations. The Covasim model could include improvements to better simulate real-world epidemic conditions, including a revised transmission strategy to account for accumulation through daily contacts. In addition, we propose to add a module for intercity travel and a visualization package that will significantly expand the functionality of Covasim. These improvements make Covasim a more versatile and efficient tool for modeling and analyzing epidemic processes.

Graphene-based nanomaterials have emerged as promising materials for a wide range of applications.. Therefore, in the last years carbon nanoparticles have attracted great attention due to their low toxicity, high biocompatibility and easy preparation. Recently, N-doped carbon nanoparticles have been shown to have improved antibacterial activity over the undoped nanomaterial, but it is difficult to find correlations between the structure of the nanoparticle and its antibacterial activity. With this purpose, here, we analyze the effect of both, the nanoparticle size and the surface chemical composition of four N-doped carbon nanoparticles on the growth of Escherichia coli bacteria. Our results were analyzed using a Ligand-Substrate model based on the Monod´s equation, which allows us to interpret the dependence of the nanoparticle-bacteria affinity with the nanomaterial structure.

The use of nanoparticles as antimicrobial agents can be one of the strategies to overcome the tendency of microbes to become resistant to antibiotics’ action. In this study, two composites ZnO/Au and ZnO/Ag, having 1% wt. of noble metal content, were synthesized by simple aqueous solution methods. The structure and morphology of the resulting nanocomposites were analyzed by standard structural and optical characterization methods. The formation of Au NPs and Ag NPs in these experiments was also discussed. The antimicrobial properties of ZnO, ZnO/Au and ZnO/Ag nanomaterials were investigated against Gram-negative bacteria (Pseudomonas aeruginosa) and Gram-positive bacteria (Staphylococcus aureus). The electrostatic interaction between ZnO and noble metals nanoparticles have contributed to a better visible light adsorption, which led to an enhanced antimicrobial activity. The photocatalytic tests indicated an improvement in photocatalytic degradation of the methylene blue (MB) under UV irradiation using ZnO/Au and ZnO/Ag nanocomposites compared to bare ZnO. The introduction of noble metallic nanoparticles in ZnO matrix proved to be an effective strategy to increase their antimicrobial activity against P. aeruginosa and S. aureus and their photocatalytic activity evaluated through the degradation of MB dye. Comparing the enhancing effects of Au and Ag, it was found that ZnO/Au was a better antimicrobial agent while ZnO/Ag was more effective photocatalyst under UV irradiation.

Egg white lysozyme was modified by chemical methods using organic acids. Caffeic acid and p-coumaric acid in organic acids were used as modifiers, and 1-Ethyl-3- (3-dimethylaminopropyl) carbodiimide hydrochloride and N-hydroxy succinimide were used as dehydration condensation agents during modification. A certain degree of modified lysozyme was obtained through appropriate modification conditions. The antibacterial properties and structure of the obtained two organic acid modified lysozymes were compared with natural enzymes. The results showed that compared with the natural enzyme, the activity of modified lysozyme decreased, but the inhibitory effect on Gram-negative bacteria was enhanced. The minimum inhibitory concentrations of caffeic acid modified enzyme and p-coumaric acid modified enzyme on Escherichia coli and Pseudomonas aeruginosa were 0.5 mg/mL and 0.75 mg/mL, respectively. However, the antibacterial ability of modified lysozyme to Gram-positive bacteria was lower than that of natural enzyme. The minimum inhibitory concentration of caffeic acid modified enzyme and p-coumaric acid modified enzyme to Staphylococcus aureus and Bacillus subtilis was 1.25 mg/mL. The peak fitting results of the amide-I band (1600 cm-1-1700 cm-1) absorption peak in the infrared spectroscopy showed that the content of the secondary structure of the two modified enzymes obtained after modification was different from that of natural enzymes.

To date, various chimeric lysins have been developed as efficacious antibiotics against multidrug-resistant bacteria, but direct comparisons of their antibacterial activities have been difficult due to the preparation of multiple recombinant chimeric lysins. Previously, we reported an E. coli cell-free expression method to screen better chimeric lysins against Staphylococcus aureus, but we still needed to increase the amounts of expressed proteins enough to be able to detect them non-isotopically for quantity comparisons. In this study, we improved the previous cell-free expression system by adding a previously reported artificial T7 terminator and reversing the different nucleotides between the T7 promoter and start codon to those of the T7 phage. The new method increased the expressed amount of chimeric lysins enough for us to detect them using Western blotting. Therefore, the qualitative comparison of activity between different chimeric lysins has become possible via the adjustment of the amount variables between samples without protein purification. We applied it to select more active chimeric lysins derived from our previously reported chimeric lysin (ALS2). Finally, we compared the antibacterial activities of our selected chimeric lysins with reported chimeric lysins (ClyC and ClyO) and lysostaphin, and determined the rank orders of antibacterial activities on different S. aureus strains in our experimental conditions.

In this paper, we unite concepts from Husserlian phenomenology, the active inference framework in theoretical biology, and category theory in mathematics to develop a comprehensive framework for understanding social action premised on shared goals. We begin with an overview of Husserlian phenomenology, focusing on aspects of inner time consciousness, namely, retention, primal impression, and protention. We then review active inference as a formal approach to modeling agent behavior, based on variational (approximate Bayesian) inference. Expanding upon Husserl’s model of time consciousness, we consider collective goal-directed behavior, emphasizing shared protentions among agents and their connection to the shared generative models of active inference. This integrated framework aims to formalize shared goals in terms of shared protentions, and to thereby shed light on the emergence of group intentionality. Building on this foundation, we incorporate mathematical tools from category theory; particularly, sheaf and topos theory, to furnish a mathematical image of individual and group interactions within a stochastic environment. Specifically, we employ morphisms between polynomial representations of individual agent models, allowing predictions not only of their own behaviors but also those of other agents and environmental responses. Sheaf and topos theory facilitate the construction of coherent agent worldviews and provides a way of representing consensus or shared understanding. We explore the emergence of shared protentions, bridging the phenomenology of temporal structure, multi-agent active inference systems, and category theory. Shared protentions are highlighted as pivotal for coordination and achieving common objectives. We conclude by acknowledging the intricacies stemming from stochastic systems and uncertainties in realizing shared goals.

Savolitinib is a highly selective small molecule inhibitor of the mesenchymal epithelial transition factor (MET) tyrosine kinase, primarily developed for the treatment of non-small cell lung cancer (NSCLC) with MET mutations. It is also being investigated as a treatment for breast, head and neck, colorectal, gastric, pancreatic, and other gastrointestinal cancers. In both preclinical and clinical studies, it has demonstrated efficacy in lung, kidney, and stomach cancers. Savolitinib is an oral anti-cancer medication taken as a 600 mg dose once daily. It can be used as a monotherapy in patients with non-small cell lung cancer with MET mutations, and in combination with epidermal growth factor receptor (EGFR) inhibitors for patients who have developed resistance to them. Furthermore, savolitinib has shown positive results in gastric cancer treatment, particularly in combination with docetaxel. As a result, this review aims to validate its efficacy in NSCLC and suggests its potential application in other gastrointestinal cancers, such as pancreatic cancer, based on related research in gastric and renal cancer.

This paper starts with hypothesis (and presents some evidence) that anxiety in migrants is sufficiently important to be modelled. It presents a small (and very incomplete) review of emotion modelling in literature. It asks the question of how to translate these into agent-based modelling, and whether this can be orthogonal to specific modelling of goals and capabilities of agents. This short paper is offered as a motivator for discussion, rather than a discussion of results.

Gambogic acid, a common traditional Chinese medicine and widely distributed throughout South China, Vietnam, Cambodia, and Thailand. It is prenylated xanthone which is the significant bioactive compound of gamboge. Gambogic acid is known as a strong apoptotic inducer in cancer cells. It has been found as strong anticancer agent against various types of cancer cells lines such as breast cancer, pancreatic, and cervical cancer. It induces apoptosis, down regulates the anti-apoptotic proteins (survivin and BCL2,) and down regulates the activities of P-glycoprotein in drug sensitive human breast MCF-7 and drug-resistant MCF-7/ADR cells. Similarly, it also exerts alteration in P13K, AKT, p21, MMP-2 &-9, and phosphorylated-AKT expressions. The current review highlights the anticancer and chemo-preventive perspectives of gambogic acid and its mechanistic role against human and animal cancers.

In this study, we report the antibacterial mechanisms of action of uniform silver nanoparticles (AgNPs) and decorated activated carbon nanocomposite (CAC-AgNPs) obtained using a green synthesis approach. The nanomaterials were characterized by ultraviolet-visible (UV-vis) absorption spectra and Fourier transform infrared (FTIR) spectra. The antibacterial activity of the as-prepared nanomaterials was evaluated against an array of bacterial strains by microdilution method, whereas their cytotoxicity profile was evaluated on Vero cells (human mammalian cells). The antibacterial mechanistic studies of active nanomaterials were carried out through bacterial growth kinetics, nucleic acid leakage test, and catalase inhibition assay. A silver nanocomposite was successfully fabricated from Croton macrostachyus-based activated carbon. The as-prepared nanomaterials exhibited antibacterial activity against an array of bacterial strains (minimum inhibitory concentration (MIC) range: 62.5 to 500 µg/mL), the most susceptible being Escherichia coli and Staphylococcus aureus. Cytotoxicity studies of the nanomaterials on Vero cells revealed that the nanocomposite (median cytotoxic concentration (CC50): 213.6 µg/mL) was less toxic than the nanoparticles (CC50 value: 164.75 µg/mL) counterpart. Antibacterial mechanistic studies unveiled that the nanomaterials induced (i) bacteriostatic activity vis-à-vis E. coli and S. aureus and (ii) inhibition of catalase in these bacteria. This novel contribution on the antibacterial mechanisms of action of silver nanocomposite from C. macrostachyus-based activated carbon might contribute to the understanding of antibacterial action of these biomaterials. Nevertheless, more chemistry and in vivo experiments, as well as in depth antibacterial mechanistic studies are warranted for the successful utilization of these antibacterial biomaterials.

Marine microalgae are a rich reservoir of natural compounds, including bioactives. Nonetheless, these organisms remain fairly unexplored despite their potential biotechnological applications. Culture collections with diverse taxonomic groups and lifestyles are a good source to unlock this potential and discover new molecules for multiple applications such as the treatment of human pathologies or the production of aquaculture species. In the present work extracts from 33 strains (including 20 dinoflagellates, 4 diatoms and 9 strains from other 7 algal classes), cultivated under identical conditions were examined for antiviral, antibacterial, anti-inflammatory and anti-cancer activities. Among these, antiviral and anti-inflammatory activities were detected in a few strains while antibacterial tests showed positive results in most assays. In turn, most trials did not show any anti-cancer activity. Wide differences were observed between species within the same class, in particular dinoflagellates which were better represented in this study. These preliminary findings pave the way for in-depth characterization of extracts with highest signals in each test, identification of compounds responsible of the biological activities found, and a further screening of the CCVIEO culture collection.

Many medicinal plants and their essential oils are used to treat or prevent diseases without the risk of mutagenicity, carcinogenicity, or teratogenicity. Eucalyptus essential oils are commonly used as preservatives, flavoring agents, and in various consumer goods. Eucalyptus leaves are being widely studied due to their volatile essential oils, including 1,8-cineole, p-cymene, α and β-pinene, limonene, citronellal, citral, eudesmol, terpinen-4-ol, terpineol, α–phellanderene, and 9β-sitosterol. Among these compounds, 1,8-cineole is the most abundant. Eucalyptus leaves are rich in flavonoids and phenolic compounds and are thus a great source of antioxidants. 2,2-diphenyl-1-picrylhydrazyl (DPPH), Ferric Reducing Antioxidant Power (FRAP), and 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) assays are used to measure antioxidant capacity. The antioxidant activity of Eucalyptus essential oil is stronger than that of standard antibiotics like Erythromycin, Cefixime, and Gentamicin due to the presence of significant terpenoids in addition to phenolic chemicals and flavonoids. The lower the IC₅₀ value, the higher the antioxidant potential. Phenolic compounds and flavonoids are often associated with beneficial health outcomes, including anti-inflammatory and antioxidant effects, anti-cancer properties, reduced risk of cardiovascular diseases, prevention of age-related neurodegenerative diseases, and prevention of Alzheimer’s disease. Flavonoids also play an essential role in plants, including protecting against reduction, fertility, reproduction, and infection. Due to their anti-inflammatory, anti-oxidative, and immune-modulatory properties, flavonoids are crucial for pharmacological, medical, and nutraceutical applications.

Tin (IV) oxide nanoparticles (SnO2 NPs) have received a lot of interest because of their interesting features. SnO2 NPs have proven productive in a range of fields, including water purification, supercapacitors, batteries, antibacterial and antioxidant agents, and others. SnO2-based nanoparticles found a wide range of applications after incorporating materials with varying chemical compositions. SnO2 NPs and their nanocomposites have been used effectively as antibacterial agents against various pathogenic bacteria, photocatalysts for dye degradation, and electrode materials for supercapacitors (SCs). This article covers the characteristics of SnO2 NPs, SnO2 nanocomposite materials, applications of SnO2 NPs and their composite materials, including antibacterial, energy storage, and photocatalysis, as well as some significant recent studies.

In recent years, antibacterial coatings have become a significant approach in the global fight against bacterial pathogens. Developments in materials science, chemistry and biochemistry have led to a plethora of materials and chemical compounds that have potential for creating antibacterial coatings. Nonetheless, there has been insufficient consideration given to the analysis of the techniques and technologies used to apply these coatings. Among the various inorganic coating techniques, Atomic Layer Deposition (ALD) is noteworthy. It enables the successful synthesis of high-purity inorganic nanocoatings on surfaces of complex shape and topography, while also providing precise control over their thickness and composition. ALD has various industrial applications, but its practical application in medicine is still limited. In recent years, a substantial number of papers have been published on the suggested implementation of thin films and coatings produced through ALD in medicine, notably those with antibacterial properties. The aim of this paper is to carefully evaluate and analyse the relevant literature on this subject. Simple oxide coatings, including TiO2, ZnO, Fe2O3, MgO, and ZrO2, were examined, as well as coatings containing metal nanoparticles such as Ag, Cu, Pt, and Au, and mixed systems such as TiO2-ZnO, TiO2-ZrO2, ZnO-Al2O3, TiO2-Ag, and ZnO-Ag. Through comparative analysis, we have been able to draw conclusions on the effectiveness of various antibacterial coatings of different compositions, including key characteristics such as thickness, morphology, and crystal structure. ALD has been analysed in its use for developing antibacterial coatings for various applications. Furthermore, assumptions regarding the most promising development areas have been presented.

The PLM concept implies the use of heterogeneous information resources at different stages of the product life cycle, the joint work of which allows you to effectively solve the problems of product quality and various costs. According to the principle of isomorphism of regularities of complex systems, an effective PLM system must have these regularities. Unfortunately, this principle is not often fundamental when designing PLM systems. The purpose of the work is to show, using a simple example, the principles of development, operation and use of an educational multi-agent PLM system, the main purpose of which is to study and research these regularities in the life cycle of a special threaded connection. The multi-agent approach to the development of a PLM system provides the necessary prerequisites for the emergence of system-wide regularities in it. The parallel work of agents is implemented using the actor model and the Ray Python-package. Agents for the logical inference of knowledge base facts, CAD/FEA/CAM/SCADA agents, agents for optimization by various methods, and other agents have been developed. Open source software was used to develop the system. Each agent has relatively simple behavior, implemented by its rule function, and can interact with other agents. The system can work in interactive mode with the user or in automatic mode according to a simple algorithm: the rule functions of all agents are executed until at least one of them returns a value other than None. Examples of the operation of the system are given and such system-wide regularities as emergence, historicity and self-organization are demonstrated in it.

At this time, nanoparticles used to been considered for various biomedical applications due to their particular properties[1, 2]. It is already known that one of the major advances in the relative application of nanoparticles is the recognition of the steric stabilization which can increase the particle stability in the biological environment and provide the opportunities of the application of nanoparticles in the development of drug delivery systems (DDSs) for achieving drug targeting and controlled drug release. Nano crystalline silver particles (AgNPs) have major applications in biomolecular recognition of highly sensitive, anti-microbial treatment, catalysis and manufacture sensors [3-7]. The NPs for various applications medical like image quality, medicine, tissue, magnetic resonance imaging (MRI) of targeting tissues and cells styles. This is particularly the case of AgNPs significantly encompasses the whole a wide range of industrial and medical applications. In this study, we have been synthesized incorporated omeprazole and omeprazole sulfide drugs with AgNPs and the results was investigated with TEM, FT-IR, DRS and XRD. The particle size has been seen in imaging TEM about 80 nm. Moreover either Omeprazole@AgNPs or omeprazole sulfide@AgNPs are able to excrete bacteria. In this study, the antibacterial properties of drugs with silver nanoparticles also increased.

With the increased scientific interest in green technologies, many researches have been focused on the production of polymeric composites containing naturally occurring reinforcing particles. Apart from increasing mechanical properties, these additions can have a wide range of interesting effects, such as increasing the resistance to bacterial and fungal colonization. In this work, different amounts of two different natural products, namely neem and turmeric, have been added to polyethylene to act as a natural antibacterial and antifungal product for food packaging applications. Microscopic and spectroscopic characterization showed that fractions up to 5% of these products can be dispersed into low-molecular weight polyethylene, while higher amounts could not be properly dispersed and resulted in an inhomogeneous, fragile composite. In vitro testing conducted with Escherichia coli, Staphylococcus aureus and Candida albicans showed a reduced proliferation of pathogens when compared to the polyethylene references. In particular, turmeric, resulted to be more effective against E. coli when compared to neem, while they had similar performances against S. aureus. Against C. albicans, only neem was able to show a good antifungal behavior, at high concentrations. Tensile testing showed that the addition of reinforcing particles reduces the mechanical properties of polyethylene, and, in the case of turmeric, it is further reduced by UV irradiation.

The study of biologically active substances from natural sources shows the prospect of obtaining a new type of antimicrobial agents, highly effective against pathogenic microorganisms and non-toxic to humans. Our study reveals for the first time that Cornu aspersum mucus has the potential to act as a source of antibacterial agents against bacterial pathogens such as Bacillus cereus 1085, Propionibacterium acnes 1897, Salmonella enterica 8691, Enterococcus faecalis 3915, and Enterococcus faecium 8754. Both mucus fractions with MW<20 kDa and MW>20 kDa showed antimicrobial activity and antioxidant properties that’s why they can be turned into an alternative agent to expensive synthetic antibacterial compounds. Using de novo sequencing 16 novel peptides with potential antibacterial activity were identified by in a fraction with MW<20 kDa. The results of electrophoretic and proteomic analysis of mucus fraction with MW >20 kDa presented proteins with potential antibacterial activity highly homologous to hemocyanins, mucus protein Aspernin, lectins, L-amino acid oxidase-like protein, and mucins (mucin-5AC, mucin-5B, mucin-2 and mucin-17). Thanks to the synergistic action of the bioactive components, the mucus fraction with MW > 20 kDa in low concentrations per 8–2 µg/mL showed promising antimicrobial activity against the tested bacteria, comparable to Vancomycin and without unwanted cytotoxic effects against non-target cells. Additionally, C. aspersum mucus fractions were found to have a positive effect on eukaryotic organisms by reducing the levels of intracellular oxidative damage and increasing the antioxidant capacity of the cell. These findings could serve as a basis for the development of a potent non-cytotoxic antibacterial agent to replace conventional antibiotics and avoid the development of antibiotic resistance.

Classical antibacterial drugs were designed to target specific bacterial properties distinct from host human cells to maximize potency and selectivity. These designs were quite effective as they could be easily derivatized to bear next generation drugs. However, the rapid mutation of bacteria and their associated acquired drug resistance have led to the rise of highly pathogenic superbug bacterial strains for which treatment with first line drugs is no match. More than ever, there is a dire need for antibacterial drug design that goes beyond conventional standards. Taking inspiration by the body’s innate immune response to employ its own supply of labile copper ions in a toxic attack against pathogenic bacteria, which have a very low Cu tolerance, this review article examines the feasibility of Cu-centric strategies for antibacterial preventative and therapeutic applications. Promising results are shown for the use of Cu-containing materials in the hospital setting to minimize patient bacterial infections. Studies directed at disrupting bacterial Cu regulatory pathways elucidate new drug targets that can enable toxic increase of Cu levels and perturb bacterial dependence on iron. Likewise, Cu intracellular chelation/prochelation strategies effectively induce bacterial Cu toxicity. Cu-based small molecules and nanoparticles demonstrate the importance of the Cu ions in their mechanism and display potential synergism with classical drugs.

Background: Bacterial infections constantly have a large impact on public health, because of increased rates of resistance and reduced frequency of development of novel antibiotics. The utility of conventional antibiotics for treating bacterial infections has become increasingly challenging. The aim of the study was to assess the antibacterial effect of β -Lapachone, a novel synthetic compound. Methods: The antibacterial activity of the β -Lapachone compound was examined against laboratory strains by agar well diffusion method, minimal inhibitory concentration (MICs), and minimal bactericidal concentration (MBCs). Growth kinetics inhibition in presence of β -Lapachone on Staphylococcus aureus, Staphylococcus epidermidis and Pseudomonas aeruginosa (ATCC 27853) was assessed by MABA. Crystal violet blue assay was used for biofilm inhibition assays, biofilm eradication assay and for molecular modeling PyMOL was used. Results: β -Lapachone exhibited potent antimicrobial activity against laboratory strains of bacteria with MIC of 0.2 mM for S. saprophyticus and Staphylococcus aureus, and 0.04 mM for Staphylococcus epidermidis and Pseudomonas aeruginosa ATCC 27853. The inhibition of catalase enzyme was found to be the cause for its antibacterial activity. Molecular modeling predicted the binding of β -Lap at active site and heme binding site of catalase, KatA. The activity of some commercial antibiotics was enhanced in association with β -Lap. In addition, β -Lap inhibited the biofilm formation and eradicated the already formed and ultra-mature biofilms of aforesaid bacterial strains.

Tumor necrosis factor-α (TNFα), one of the major pro-inflammatory cytokines, plays a key role in an effective immune response. However, the chronic presence of TNFα can lead to several inflammatory disorders like rheumatoid arthritis, psoriasis, Crohn’s disease etc. Inhibition of TNFα by pharmacological inhibitors or antibodies has proven to be effective in palliative treatment to some extent. The aim of this study was to develop an anti-TNFα antibody which may be used as a therapeutic option to inhibit TNFα-mediated cytotoxicity. We characterized several hybridoma clones secreting monoclonal antibodies (mAbs) to human-TNFα. Four mAbs rescued L929 fibroblast cells from TNFα-triggered cell death and one of these, namely C8 was found to have the highest affinity. To gain insights into the mechanism by which mAb C8 inhibits human TNFα-mediated toxicity, the epitope corresponding to the mAb was delineated. The antigenic determinant was found to comprise of the stretch of amino acids 99-120, of which, 102-104 (QRE) form the core epitope. The observation was supported by bioinformatics analyses of an antigen-antibody complex model. In addition, the binding affinity of mAb C8 to TNFα was found to be comparable with that of Infliximab which is a commercially available anti TNFα mAb.

In this study, we examine the relationship of bank level lending and borrowing decisions and the risk preferences on the dynamics of the interbank lending We develop an agent-based model that incorporates individual bank decisions using the temporal difference reinforcement learning algorithm with empirical data of 6600 S. banks. The model can successfully replicate the key characteristics of interbank lending and borrowing relationships documented in the recent literatur A key finding of this study is that risk preferences at individual bank level can lead to unique interbank market structures which are suggestive of the capacity that the market responds to surprising

Many bio-applicable materials, medical devices, and prosthetics combine both polymer and metal components to benefit from their complementary properties. This goal is normally achieved by their mechanical bonding or casting only. Here, we report an alternative easy method for the chemical grafting of a polymer on the surfaces of a metal or metal alloys using alkoxy amine salt as a coupling agent. The surface morphology of the created composites was studied by various microscopy methods, and their surface area and porosity were determined by adsorption/desorption nitrogen isotherms. The surface chemical composition was also examined by various spectroscopy techniques and electrokinetic analysis. Elements distribution on the surface was determined and successful bonding of the metal/alloys on one side with the polymer on the other one was confirmed by alkoxy amine. The composites show significantly increased wettability, reliable chemical stability of the bonding, excellent bacterial anti-adhesive properties and functionality, i.e. the characteristics promising for their application in biomedical field.

Introduction: Among the many factors that may limit effective wound healing in patients with chronic ulcers, bacterial infection and poor cell recruitment are primary causes that contribute to prolonged healing. Thus, a novel strategy that aims to prevent bacterial infection within the wound, while at the same time providing structural scaffolding that promotes endogenous tissue repair, would be of great interest. Here, we developed a thermo-sensitive silver nanoparticle hydrogel composite as an antibacterial nutritional scaffold for the wound that contains all nutrients required for cell growth while preventing bacterial infection with the ability to fill up all the cavities and void areas in wounds regardless of their geometry. Methods: Silver nanoparticles (AgNPs) were synthesized by chemical reduction. After characterization, silver hydrogel nanocomposite was developed by reconstitution of collagen-based hydrogel powder in a nanoparticle suspension of varying AgNPs concentrations (200, 400, and 600 ppm). The antibacterial activity of the formulations was examined in vitro and in vivo in subcutaneous implant infected model. The wound healing efficacy of the hydrogel nanocomposite was also evaluated using a splinted wound model in rats through comparison of clinical wound measurements and histological assessments. Cytocompatibility assay and biochemical analysis of blood at the end of in vivo wound healing study were performed to evaluate the safety of formulations. Results: The synthesized nanoparticles were spherical and stable. While hydrogel alone did not show any bacterial reduction in vitro, the inhibition of bacterial growth was significant in all silver hydrogel nanocomposites compared to controls (p <0.05) and was dose-dependent, with maximum reduction observed in the 600 ppm group (4.56±0.26 LOG CFU/mL, P<0.001). All concentrations of AgNPs hydrogel composites showed significant antibacterial activity in vivo as well (P<0.0001). Treatment of splinted wounds with AgNPs hydrogel composite resulted in faster wound closure and accelerated wound re-epithelialization. The formulations were non-cytotoxic and did not differ significantly in hematological and biochemical factors from the control group in in vivo study. Conclusions: By presenting promising antibacterial and wound healing activity, silver hydrogel nanocomposite offers a safe therapeutic option that can be used as a functional scaffold for an acceleration of wound healing.

Jade waste is a normal byproduct that makes up much more than the amount of jade extracted. Therefore, recycling jade waste is worth investigating from the point of view of energy conservation. Moreover, it is an environment-friendly material, which is desirable for use in building materials. In this study, Xiuyan jade waste was repurposed as antibacterial additives for building coatings. The powder waste was activated by milling and subsequent annealing. The antibacterial properties of the treated waste were mostly related to the annealing temperatures. Based on the investigations of the phase change and the release of metal ions of a series of samples and their antibacterial activities, the antibacterial mechanism of the treated samples was explored experimentally. The most applicable sample for coatings was finally chosen by considering its pH values and its antibacterial abilities. Antibacterial testing showed that the addition of treated jade waste could enhance the bacterial inhibition rate of building coatings from 60% to 99.9%.

The prevalence of multidrug resistant bacterial diseases is a major global health risk. Multidrug resistant bacterial diseases are prevalent, and the need for novel methods of treatment is essential to the preservation of public health. Annually foodborne pathogens cause 1.35 million infections and 26,500 hospitalizations in the United States alone. Foodborne pathogens such as Salmonella spp. are a major threat to public health. Bacteriophages offer a unique method for the treatment of these multidrug resistant bacteria. We studied the infection dynamics of a potential mono-phage therapy of Salmonella typhimurium under various pathophysiological conditions. Furthermore, we determined the resistance dynamics of Salmonella typhimurium against P22 phage treatment. We also determined synergy with antibiotics such as ampicillin and kanamycin. This research helps to further define and show the versatility of bacteriophages as potential novel treatment methods.

Peri-implantitis occurs at a significant rate, which is the leading cause of implant failure. The main reason for this unwanted complication is bacterial invasion and biofilm formation. To reduce the incidence of peri-implantitis, we constructed a carboxymethyl dextran (CMD) based nanomicelles antibacterial coating on microarc-oxidized titanium (MAO-Ti) surface. After cross-linking, the drug-loaded nanomicelles were spherical with a particle size of 130nm and uniformly dispersed. Zeta potential was negative, and the absolute value was greater than 10 mV, effectively avoiding micelles aggregation. It was observed by dynamic light scattering (DLS) that the stability of nanomicelles was significantly improved after cross-linking. The hemolysis rate of micelles was less than 5%, and the overall survival rate of human umbilical vein endothelial cells was more than 90%. After being coated on MAO-Ti surface, the cumulative drug release rate of drug-loaded nanomicelles reached 86.6% after 360 hours. Fluorescence staining of immobilized bacteria showed more dead bacteria on the coating surface, and the number of live bacteria was significantly reduced. It was concluded that dextran-based nanomicelles, which showed long-term drug release properties and excellent biocompatibility, are potential drug carriers for fabricating antibacterial coating on titanium surfaces.

Cranio-maxillofacial structure is a region of particular interest in the field of regenerative medicine due to both its anatomical complexity and the numerous abnormalities affecting this area. However, this anatomical complexity is what makes possible the coexistence of different microbial ecosystems in the oral cavity and the maxillofacial region, contributing to the increased risk of bacterial infections. In this regard, different materials have been used for their application in this field. These materials can be obtained from natural and renewable feedstocks or by synthetic routes with desired mechanical properties, biocompatibility and antimicrobial activity. Hence, in this review, we have focused on bio-based polymers, which by their own nature, by chemical modifications of their structure, or by their combination with other elements, provide a useful antibacterial activity as well as the suitable conditions for cranio-maxillofacial tissue regeneration. This approach has not been reviewed previously, and we have specifically arranged the content of this article according to the resulting material and its corresponding application, reviewing guided bone regeneration membranes; bone cements; and devices and scaffolds for both soft and hard maxillofacial tissue regeneration, including hybrid scaffolds, dental implants, hydrogels and composites.

Antimicrobial peptides and structurally related peptoids offer potential for the development of new antibiotics. However, progress has been hindered by challenges presented by poor in vivo stability (peptides) or lack of selectivity (peptoids). Herein, we have developed a process to prepare novel hybrid antibacterial agents that combine both linear peptoids (increased in vivo stability compared to peptides) and a nisin fragment (lipid II targeting domain). The hybrid nisin-peptoids prepared were shown to have low µM activity (comparable to natural nisin) against methicillin-resistant Staphylococcus aureus.

A new method for the synthesis of azido-propargyloxy derivatives of 1,3,5-triazine has been developed. The antibacterial activity against E. coli bacteria of propargyloxy substituted 1,3,5-triazines - 2,4,6-trispropargyloxy-1,3,5-triazine, 2-azido-4,6-bispropargyloxy-1,3,5-triazine and 2,4-diazido-6-propargyloxy-1,3,5-triazine and their hyperbranched polymers. It has been shown that the presence of an azide group in the compound directly affects the antibacterial activity. The cytotoxicity of these compounds against the M-HeLa, FetMSC and Vero cell lines was studied. The IC50 value was determined for low molecular weight compounds. It has been shown that hyperbranched polymers without azide groups don’t exhibit pronounced cytotoxicity and can be used in biomedical applications.

Zingiber cassumunar Roxb. is a powerful medicinal plant that has been used as traditional medicine to cure respiratory problems, pain, and inflammation in China, Indonesia, Thailand and other Asian countries by using the crude extracts. The objective of this research is to identify phytochemical composition of Z. cassumunar Roxb. and to analyze antibacterial activity of crude extract, purified compounds, and their microencapsulated products of Rhizome Z. cassumunar Roxb. Identification of phytochemical composition in crude extract of rhizome Z. cassumunar Roxb. was achieved by chromatography-mass spectrophotometer. The major phytochemical composition in crude extract of Z. cassumunar Roxb. is essential oils, including terpinen4-ol (37.7%), β-pinene (20.8%), and (E)-1-(3,4-dimethoxyphenyl)but-1-ene (13.3%). Crude extract of Z. cassumunar Roxb. was purified with silica gel flash column chromatography, resulting two purified compounds. The antibacterial activity of crude extract, purified compounds, and their microencapsulated products of Rhizome Z. cassumunar Roxb. were evaluated against agricultural and foodborne pathogens by using disc agar diffusion and broth microdilution techniques. All of the samples studied (crude extracts, purified compounds, and microencapsulated of Z. cassumunar Roxb.) were effective against all the bacteria. Based on the results of the disc-diffusion assay suggested that amongst the samples studied, purified compounds (compound 1 and 2) and microencapsulated purified compounds (compound 1 and 2) exhibited more effective against all the bacteria compared to the crude extracts. Antibacterial activity of the rhizome of Z. cassumunar Roxb. was contributed mainly by the essential oils components as the active compounds. Gram-negative bacteria (X. oryzae, X. translucens, Pseudomonas spp, E. coli, and S. typhimurium) appeared to the most resistant to the crude extracts, purified compounds, and microencapsulated of Z. cassumunar Roxb. compared to the gram-positive bacteria (S. aureus, B. cereus, and L. monocytogenes). Microencapsulated of the tested samples (crude extract, purified compound 1, and purified compound 2) of the rhizome Z. cassumunar Roxb. exhibited high antibacterial activity with no significantly different with the tested samples without microencapsulation. These results suggest potential antibacterial properties of Z. cassumunar Roxb., which useful for agricultural plant health, food preservation, natural therapies, and pharmaceuticals.

Flavan-3-ols and their oligomeric forms called proanthocyanidins are polyphenolic compounds occurring in several foodstuffs and in many medicinal herbs. Their consumption is associated with numerous health benefits. Their bioactivities include antioxidant, anti-inflammatory, cytoprotective, as well as antimicrobial. The latter property is important in prevention and treatment of periodontal diseases. Periodontitis is a multifactorial polymicrobial infection characterized by a destructive inflammatory process affecting the periodontium. Using non-toxic and efficient natural products such as flavanol derivatives can significantly contribute to alleviating of periodontitis symptoms and prevent the disease progress. In this paper, we systematically review the state-of-the art in antibacterial effects of these compounds from the viewpoint of gum health. There is a significant evidence supporting an importance of antibacterial action exerted by proanthocyanidins from edible fruits, tea and medicinal herbs in inhibition of periodontitis-causing pathogens.

Neisseria gonorrhoeae is a bacterium that causes the sexually transmitted infection gonorrhea. This study employed molecular docking simulations to investigate potential interactions between natural molecules and the Fe(3+) ions import ATP-binding protein fbpC in Neisseria gonorrhoeae FA 1090. Among the screened molecules, Hypericin exhibited a remarkable binding energy of approximately -13.2 kcal/mol, indicating a robust and favorable binding affinity with the target protein. This promising outcome suggests that Hypericin could serve as a potential candidate for further exploration as a therapeutic agent against Neisseria gonorrhoeae infections. However, it is imperative to emphasize that these in silico findings necessitate experimental validation through in vitro and in vivo studies to ascertain the actual efficacy and safety of Hypericin as a treatment option.

In this research, we present the first steps taken towards a data-driven agent-based model (ABM) specifically designed for simulating infectious disease dynamics in Greece. Amidst the ongoing COVID-19 pandemic caused by SARS-CoV-2, this research holds significant importance as it can offer valuable insights into disease transmission patterns and assist in devising effective intervention strategies. To the best of our knowledge, no similar study has been conducted in Greece. We constructed a prototype ABM that utilizes publicly accessible data to accurately represent the complex interactions and dynamics of disease spread in the Greek population. By incorporating demographic information and behavioral patterns, our model captures the specific characteristics of Greece, enabling accurate and context-specific simulations. By using our proposed ABM, we aim to assist policymakers in making informed decisions regarding disease control and prevention. Through the use of simulations, policymakers have the opportunity to explore different scenarios and predict the possible results of various intervention measures. These may include strategies like testing approaches, contact tracing, vaccination campaigns, and social distancing measures. Through these simulations, policymakers can assess the effectiveness and feasibility of these interventions, leading to the development of well-informed strategies aimed at reducing the impact of infectious diseases on the Greek population. This study is an initial exploration toward understanding disease transmission patterns and a first step towards formulating effective intervention strategies for Greece.

The acylation of amines has always attracted a deep interest as a synthetic route due to its high versatility in organic chemistry and biochemical processes. The purpose of this article is to depict a mechanochemical acylation procedure based on the use of acyl-saccharin derivatives, namely N-formylsaccharin, N-acetylsaccharin and N-propionylsaccharin. This protocol furnishes a valuable solventless alternative to the existing processes and aims to be highly beneficial in multi-step procedures due to its rapid and user-friendly workup.

We first review the literature on machine behavior which may contain the interaction between machines, and then discuss the methodology and the related case involving collaboration between robots to instantiate the concept with AI empowerment. The navigation case aims to a security application with autonomous control and roadside agent embedded in a mobile edge computing structure. In the studied navigation based on the artificial potential field method, robots need to use position information to calculate the moving direction frequently. In the case of high motion speed as well as GPS positioning error, the path trajectory may show a sharp change of direction. In order to mitigate the trajectory oscillation, this paper proposes a path planning design where training process and motion direction prediction are integrated by using artificial neural network. The auxiliary navigation agent near multiple obstacles can first extract the past movement information of the robot and then determines whether there is a serious path jitter event. Computer simulation analysis shows that the combination of autonomous control and cooperative behavior can effectively reduce the path jitter so as to achieve a fast and safe path planning.

Graphene oxide (GO), nanographene oxide (nGO) and partially reduced graphene oxide (rGO) have been studied as possible foam stabilizing agents for CO₂ based enhanced oil recovery (EOR). GO was able to stabilize CO₂/synthetic sea water foams. rGO was not able to stabilize foams likely due to the high reduction degree of the material. Particle size had a strong influence on foamability and stability. GO hydrophilicity increased as the particle size decreased and no foams were created when particle size was below 1 µm (nGO). GO brine dispersions showed immediate gel formation, which improved foam stability. Particle growth due to layer stacking was also observed. This mechanism was detrimental for foam formation and stabilization. nGO dispersed in synthetic sea water rapidly formed hydrogels and was not filterable. This work indicates that the particles studied are not suitable for CO₂ EOR purposes.

Hydrogel wound dressings hold great potential in eliminating bacteria and accelerating the healing process. However, it remains a challenge to fabricate hydrogel wound dressings that simultaneously exhibit excellent mechanical and photothermal antibacterial properties. Here we report the development of polydopamine-functionalized graphene oxide/calcium alginate/Polypyrrole cotton fabric-reinforced hydrogels (abbreviated as rGO@PDA/CA/PPy FHs) for tackling bacterial infections. The mechanical properties of hydrogels were greatly enhanced by cotton fabric reinforcement and an interpenetrating structure, while excellent broad-spectrum photothermal antibacterial properties based on the photothermal effect were obtained by incorporating PPy and rGO@PDA. Results indicated that rGO@PDA/CA/PPy FHs exhibited superior tensile strength in both the warp (289±62.1N) and weft directions (142±23.0N) similar to cotton fabric. By incorporating PPy and rGO@PDA, the swelling ratio was significantly decreased from 673.5% to 236.6%, while photothermal conversion performance was significantly enhanced with a temperature elevated to 45.0 ℃. Due to the synergistic photothermal properties of rGO@PDA and PPy, rGO@PDA/CA/PPy FHs exhibited excellent bacteria-eliminating efficiency for S. aureus (0.57%) and E. coli (3.58%) after exposure to NIR for 20 min. We believe that the design of fabric-reinforced hydrogels could serve as a guideline for developing hydrogel wound dressings with improved mechanical properties and broad-spectrum photothermal antibacterial properties for infected wound treatment.

This study aimed to elucidate the antibacterial efficacy and unique chemical compositions generated from plasma-activated water (PAW) when utilized a novel vaginal cleansing device. We conducted an analysis of antibacterial activity against probiotics and several chemical compositions including ions under various operational parameters of PAW, including electrical power (12 and 24 V), treatment duration (1, 10, and 20 min), and stay duration (immediate, 30 and 60 min). Our findings revealed that as treatment duration increased, hypochlorous acid (HOCl), Ca2+, and Mg2+ concentrations increased and Cl−concentrations decreased. Higher electrical power and longer treatment duration resulted in increased HOCl levels, which acts to prevent the growth of general microorganisms. Notably, PAW exhibited no antibacterial effects against a type of probiotic, Lactobacillus reuteri that produces lactic acid for vaginal health. This result demonstrated the ability of the vaginal cleaning device to generate ions, primarily HOCl and some cations (Ca2+ and Mg2+), thereby providing vaginal mucosa protecting and cleansing effects with the vaginal environment.

Abstract: Given the increasing resistance of some bacterial strains to many common antibiotics used in the local market, the current study aimed to produce nanoscale particles capable of combating pathogenic bacteria that have developed resistance to current antibiotics. In this research, an ex-perimental study was conducted to produce nanoscale particles using the single-celled blue-green algae Synechococcus sp., which was isolated from a local environment in the Arab Republic of Egypt, specifically from a soil sample in Beni-Suef City. The aim of the study was to generate silver NPs employing different biological approaches, encompassing the direct strain powder technique, ethanol extract pellet technique, and ethanol extract technique. These synthesized nanoparticles displayed different shapes, including cubic, spherical, pellet-like, and rod-shaped particles. They were characterized by bio-functional groups containing Ag+ ions, which were detected using FT-IR, Zeta sizer, and Zeta potential measurements. High-resolution SEM imaging unveiled the mor-phological features of Silver NPs with biologically formed protective layers, spanning sizes from 20 to 430 nm for individual particles. The study evaluated the antibacterial efficiency against both G+ve and G-ve bacteria. The ethanolic extract technique exhibited the largest inhibition zone (24 mm) against G+ve bacteria, particularly Staphy. aureus. Furthermore, it was observed that the larger particles produced using the powder and pellet techniques were less effective antibacterial agents. In conclusion, this investigation emphasizes the potential of cyanobacteria-based synthesis of silver nanoparticles as a promising approach for producing innovative antimicrobial agents.

The increased emergence of multidrug-resistant Helicobacter pylori influences the prevention of stomach cancer. Zingiber officinale is a plant usually used in folk medicine to treat a variety of diseases involving infections, nausea, vomiting, peptic ulcer, dyspepsia, and inflammation. This study was conducted to evaluate the ability of Z. officinale extract to combat resistant H. pylori. The disc diffusion, microdilution, and microplate assays were performed to evaluate the susceptibility to antibiotics, and the antibacterial and antibiofilm activities of the Z. officinale extracts. Using the checkerboard method, the combined effects of the gentamicin and Z. officinale extract were investigated. In addition, anti-inflammatory activity and GC-MS analysis were determined by the modified protocol. According to the findings, H. pylori isolates exhibited resistance rates of 56.33, 50.0, and 45.85 for metronidazole, gentamicin, and tetracycline, respectively. The methanolic extract of Z. officinale had the strongest effectiveness against resistant H. pylori isolates with MIC of 20.0 to 50.0 µg/ml against both H. pylori isolates and the stranded strain NCTC 11637. Z. officinale extract suppress the biofilm formed by H. pylori isolates with a percentage of 92.96% at 50.0µg/ml, compared with 97.19% for gentamicin at the same concentration. According to FICI values, combination of methanolic Z. officinale extract to gentamicin increases bacterial sensitivity to such drugs. Moreover, the Z. officinale extract exhibits strong anti-inflammatory activity. The GC-MS analysis of Z. officinale extract exhibits 17 different chemical compounds. Conclusions: The Z. officinale extract contain the anti-inflammatory compound gingerol as the main constituent which inhibits the growth of H. pylori and its biofilm, are a promising natural therapeutic alternative or enhance antibiotics activity

Natural products are an important source of antibacterial agents. Canthin-6-one alkaloids have displayed potential antibacterial activity based on our previous work. In order to improve the activity, twenty-two new 3-N-benzylated 10-methoxy canthin-6-ones were designed and synthesized through quaternization reaction. The in vitro antibacterial activity against three bacteria was evaluated by double dilution method. Four compounds (6f, 6i, 6p and 6t) displayed 2-fold superiority (minimum inhibitory concentration (MIC) = 3.91 µg/mL) against agricultural pathogenic bacteria R. solanacearum and P. syringae than agrochemical propineb. Moreover, the structure–activity relationships (SARs) were also carefully summarized in order to guide the development of antibacterial canthin-6-one agents.

We report the production of metal oxide (TiFe₂O₄, ZnFe₂O₄) nanoparticles by pulsed laser ablation technique in liquid environment. We used nano second Nd: YAG laser systems working at 532 nm and 1064 nm of wavelength, the energy of the laser beam was kept constant at 80 mJ. Absorbance spectra, surface plasmon resonance, optical band-gap and nanoparticle morphology were investigated using ultraviolet-visible (UV-Vis) spectroscopy, Fourier transform infrared spectroscopy (FTIR), and scanning electron microscopy (SEM). Changing the wavelength of the laser for growth, nanoparticles shown shift between the absorbance and surface plasmon resonance peaks in their UV-Vis spectra, this implies that the optical properties of the colloid nanoparticles depends on laser parameters, this was confirmed with the variation of the band gap energy. Furthermore, red shift for the absorbance peak was observed for samples as-growth at 532 nm around the 150 nm as function of time preparation. Whereas, for the samples as-growth at 1064 nm there is no shift in the absorbance spectra, this can be due to agglomeration and formation of larger particles. The characterization results shown appropriate plasmonic photo-catalysts properties of the particles, hence the photo activation of the nanoparticles was examined on antibacterial effect using colonies of Staphylococcus Aureus and Escherichia coli.

This review focuses on Cu/TiO2 sequentially and Cu-TiO2 co-sputtered catalytic/photocatalytic surfaces leading to bacterial inactivation discussing their stability, synthesis, adhesion and antibacterial kinetics. The intervention of TiO2, Cu and the synergic effect of Cu and TiO2 on films prepared by a colloidal approach and other techniques is also reviewed leading to bacterial inactivation. Processes in aerobic media and anaerobic media leading to bacterial loss of viability on multidrug resistant (MDR) pathogens, Gram-negative (-) and Gram-positive(+) bacteria are described. Insight is provided for the interfacial charge transfer mechanism under solar irradiation occurring between TiO2 and Cu. surface properties of 2D TiO2/Cu and TiO2-Cu films are correlated with the bacterial inactivation kinetics observed in the dark and under light. The intervention of these antibacterial sputtered surfaces in health-care facilities leading to MRSA-isolates is described in the dark and under the actinic light. The synergic intervention of the Cu and TiO2 films leading to bacterial inactivation prepared by direct current magnetron sputtering (DCMS), pulsed direct current magnetron sputtering (DCMSP) and highly ionized pulse plasma magnetron sputtering (HIPIMS) is reported in a detailed way.

The domain of construction engineering and management is evolving rapidly. Optimizing resource positioning is crucial for meeting the challenges of efficiency and productivity. This research presents a novel methodology that incorporates Agent-Based Modeling (ABM), Building Information Modeling (BIM), and Bluetooth Low Energy (BLE) technologies, augmented with a Client Early Warning System (CEWS) and a Decision Support System (DSS). What makes this study unique is that it provides a real-time methodology for resource allocation and project management, tailored to address the complexities of modern construction projects. The application of this integrated technological framework marks a significant leap in construction management, empowering data-driven decision-making and significantly improving project efficiency. Empirically validated through a case study at Helwan University's College of Engineering and substantiated by expert surveys, this research showcases a transformative model for resource management. The findings not only underscore the practical applicability of this approach but also open new horizons for its adoption in global construction practices, offering insights for future research endeavors focused on expanding these methodologies to a wider range of resources.

Bacteria of the genus Staphylococcus are a significant a challenge for medicine, as many species are resistant to multiple antibiotics and even to all of the antibiotics used. One of the approaches to develop new therapeutics to treat staphylococcal infections is the use of bacteriophages specif-ic to these bacteria or lysins of such bacteriophages capable to hydrolyze the cell walls of these bacteria. In this study, a new bacteriophage St_134 specific to Staphylococcus epedermidis was de-scribed. This small podophage belonging to the Andhravirus genus showed relatively wide host range and was able to infect more than 60 strain of Staphylococcus spp., including a clinical strain from the Staphylococcus aureus complex. Two genes encoding different phage lysins were identi-fied in the Ste134 genome. Both lysins LysSte134_1 and LysSte134_2 were produced in Escherichia coli cells. Endolysin LysSte134_1 was demonstrated catalytic activity against a wide panel of staphylococcal peptidoglycans (4 species, 6 strains), was active against S. aureus and S. epidermidis planktonic cultures and destroyed biofilms formed by clinical strains of S. aureus and S. epider-midis.

Background. We created agent-based model for short- and longterm forecasting of COVID-19 and for evaluation how the actions of the regulator affected the human and material resources of the healthcare system. Methods. The model was implemented in the AnyLogic software. It includes two state charts – social network and disease transmission. The COVID-19 Essential Supplies Forecasting Tool (COVID-ESFT, version 2.0) was used to determine healthcare resources needed. Results. Satisfactory results were obtained with long-term (up to 50 days) forecasting in the case of a monotonous change in total cases curve. However, if periods of relative stability are accompanied by sudden outbreaks, relatively satisfactory results were obtained with short-term forecasting, up to 10 days. Simulation of various scenarios showed that the most important place for the spread of infection are families. Wherein the maximum number of cases of COVID-19 is observed in the age group of 26-59 years. Due to a set of measures taken by government agencies, the number of cases in Karaganda city was 3.2 times less than was predicted in “no intervention” scenario. Economic effect is estimated at 40 %. Conclusion. Performed model is an attempt to consider as much as possible the peculiarities of the socio-demographic situation in the country. In the future, we will be prepared to some extent for challenges like those we have experienced in the past three years.

The genus Clostridium is an important group of pathogenic and nonpathogenic Gram-positive anaerobic bacteria with sporulation capacity and wide distribution in different environments, including the gastrointestinal tract of healthy and diseased animals and humans. Among the pathogenic species of the genus, Clostridium chauvoei stands out as a histotoxic agent. It causes important myonecroses such as blackleg, a disease with high lethality and mortality, especially in young cattle, and is responsible for significant losses to livestock worldwide. The pathogenic-ity of the disease is complex and has not yet been fully elucidated. The hypotheses cover pro-cesses from the initial absorption to the transport and deposition of the agent in the affected tis-sues. The virulence factors of C. chauvoei were divided into somatic and flagellar antigens and soluble antigens/toxins, which are the main antigens involved in vaccines against blackleg in Brazil and worldwide. This review provides important information on the first and current ap-proaches to the agent C. chauvoei and its virulence factors, as well as provides a compilation of data on Brazilian studies related to blackleg.

This investigation explores a novel path-planning and optimization strategy for multiple cooperative robotic agents, applied in a fully observable and dynamically changing obstacle field. Current dynamic path planning strategies employ static algorithms operating over incremental time-steps. We propose a cooperative multi-agent (CMA) based algorithm, based on natural flocking of animals, using vector operations. It is preferred over more common graph search algorithms like A* as it can be easily applied for dynamic environments. CMA algorithm executes obstacle avoidance using static potential fields around obstacles, that scale based on relative motion. Optimization strategies including interpolation and Bezier curves are applied to the algorithm. To validate effectiveness, CMA algorithm is compared with A* using static obstacles due to lack of equivalent algorithms for dynamic environments. CMA performed comparably to A* with difference ranging from -0.2% to 1.3%. CMA algorithm is applied experimentally to achieve comparable performance, with an error range of -0.5% to 5.2%. These errors are attributed to the limitations of the Kinect V1 sensor used for obstacle detection. The algorithm was finally implemented in a 3D simulated space, indicating that it is possible to apply with drones. This algorithm shows promise for application in warehouse and inventory automation, especially when the workspace is observable.

In this paper, modelling, simulation and verification of multi-agent manufacturing system with application of bio-inspired techniques are addressed. To this end, the new solution of abstract architecture for control and coordination decentralized systems - CODESA is suggested. Centralized architecture suffers from various problems, such as rigidity, scalability, low fault-tolerance or very limited flexibility, agility, energy efficiency and productivity. Prime is concrete application of CODESA in manufacturing domain. The undesirable characteristics of emergent behaviour are the problem to achieve optimization and impossibility to predict future states of the system. CODESA-Prime has been tested by simulations for automatic guided vehicle (AGV) systems guided by magnetic tape in Ella Software Platform.

As part of valorisation of agricultural waste into bioactive compounds, a series of structurally novel oleanolic acid ((3β-hydroxyolean-12-en-28-oic acid, OA-1)-phtalimidines (isoindolinones) conjugates 18a-v bearing 1,2,3-triazole moieties were designed and synthesized by treating a previously azide 4 prepared from OA-1 isolated from olive pomace (Olea europaea L.) with a wide range of propargylated phtalimidines using the Cu(I)-catalyzed click chemistry approach. OA-1 and its newly prepared analogues 18a-v were screened in vitro for their antibacterial activity against two Gram-positive bacteria, Staphylococcus aureus and Listeria monocytogenes; and two Gram-negative bacteria, Salmonella thyphimurium and Pseudomonas aeruginosa. Attractive results were obtained notably against L. monocytogenes. Compounds 18d, 18g and 18h exhibited the highest antibacterial activity when compared with OA-1 and other compounds in the series against tested pathogenic bacterial strains. Molecular docking study was performed to explore the binding mode of the most active derivatives against the target protein from L. monocytogenes. Results showed the importance of both hydrogen bonding and hydrophobic interactions with the target protein and are in favor to the experimental data.

The emergence of multidrug-resistant strains of many pathogens is a serious threat and makes chemotherapy more difficult. The main objective of this study was to evaluate the antibacterial activity of Senna singueana and Cyphostemma junceum plant extracts against Staphylococcus aureus and Pseudomonas aeruginosa. The crude extracts of the selected medicinal plants were prepared and subjected to phytochemical screening using standard methods. Antibacterial activity was determined using the disc diffusion method. Therefore, the highest (15.41%) and lowest (0.91%) percentage yields were obtained from ethanol stem bark extracts and chloroform root extracts of Senna singueana, respectively. The maximum (14±1.0 mm) and minimum (7.5±0.5 mm) zones of inhibition were obtained from chloroform and distilled water leaf extracts of Senna singueana against Pseudomonas aeruginosa, respectively. In addition, the highest (13.5±1.0) zone of inhibition was obtained from Cyphostemma junceun root extract at 125 µg/ml. No inhibition zones were recorded in the root extract of Cyphostemma junceun at 500 µg/ml. More rich secondary metabolites, such as flavonoids, tennins, phenols, glycosides, terpenoids and sapnoids, were screened from distilled water leaf extracts, while flavonoids, tennis, phenols, glycosides, terpenoids, sapnoids and coumarins were screened in ethanol root extracts of Cyphostemma junceum. The leaves, stem bark and root of Senna singueana as well as the root of Cyphostemma junceun have strong antibacterial activity against both bacterial species. Thus, the two plant extracts could be used for healing and killing bacterial agents that can be potential sources for drug development.

This research focuses on exploring the bioactive and antibacterial properties of extracts from the flowers and bark of four Magnolia species (Magnolia champaca, Magnolia denudata, Magnolia grandiflora, and Magnolia officinalis) for possible cosmetic applications. We used ethanol to extract compounds from these plants and conducted various tests including spectrophotometry, HPLC, GC-MS, and microbiological analyses. The extracts, particularly rich in polyphenols (55.18 mg GAE/g), displayed significant antioxidant capabilities, with IC 50 values ranging between 9.99 mg/mL and 23.23 mg/mL. We quantified different compounds: phenolic acids (6.259 to 27.883 mg/g dry weight), aglycone flavonoids (61.224 to 135.788 mg/g dw), glycosidic flavonoids (17.265 to 57.961 mg/g dw), and lignans (150.071 to 374.902 mg/g dw). We identified 76 volatile compounds, predominantly oxygenated monoterpenes and sesquiterpene hydrocarbons, which contribute to the antibacterial effectiveness of the extracts. These extracts showed greater antibacterial activity against Gram-negative bacteria than Gram-positive bacteria. The diverse chemical compounds and their demonstrated activities suggest these extracts could be valuable in cosmetic, pharmaceutical, or food industries.

Background: The use of nitinol (NiTi) archwires in orthodontic treatment has expanded significantly due to unique mechanical properties. The greatest barrier to safe orthodontic treatment is chemically or microbiologically induced corrosion, resulting in Ni2+ release. The aim of this investigation was to enhance corrosion resistance and introduction antibacterial properties to NiTi archwire by coating them with TiN-Cu. Methods: NiTi archwires were coated with TiN-Cu using cathodic arc evaporation and direct current magnetron sputtering. The morphology of the sample was analyzed by FESEM and the chemical composition was assessed using EDS, XRD and FTIR. Inductively coupled plasma-optical emission spectrometry was used to estimate the ion release. Biocompatibility of samples was investigated using MTT test. Antibacterial activity was analyzed against Streptococcus mutans and Streptococcus mitis. Results: Physico-chemical characterization revealed well-designed coatings with the presence of TiN phase with incorporated Cu2+. TiN-Cu coated archwires showed statistically lower Ni2+ release (p<0.05). Relative cell viability was the highest regarding 28-day eluates of TiN-Cu coated archwires (p<0.05). The most remarkable decrease in Streptococcus mitis concentrations was observed in case of TiN-Cu coated archwires (p<0.05). Conclusion: Taking into account biocompatibility and antibacterial tests, TiN-Cu coated archwires may be considered as a good candidate further clinical investigations.

Pectin extracted via hydrodynamic cavitation in water only from waste lemon peel and further isolated via freeze drying displays significant antibacterial activity against Staphylococcus aureus, a Gram positive pathogen which easily contaminates food. The antibacterial effect of the new IntegroPectin is largely superior to that of commercial citrus pectin, opening the way to advanced applications of a new bioproduct now obtainable in large amounts and at low cost from citrus juice industry’s waste.

Background: We investigated the effect of bioactive glass and zinc oxide nanoparticles on enamel remineralization, as well as their antibacterial effect on cariogenic bacteria. Methods: Fluoride gel (F), bioactive glass microparticles (µB), bioactive glass nanoparticles (nB), zinc oxide nanoparticles (Z), and a mixed suspension of nB and Z (nBZ) were prepared and subjected to the following tests: morphological evaluation by scanning and transmission electron microscopy, measurement of specific surface area, zeta potential measurement, crystal structure analysis by X-ray diffraction, and acid buffering capacity test. Further, we performed a remineralization cycle test of 28 days and a nanoindentation testing was carried out during the immersion period and then the enamel surfaces were examined using scanning electron microscopy. Additionally, the antibacterial effects of the sample suspensions were evaluated by measuring their minimum bactericidal concentrations against various cariogenic bacteria. Results: Our results revealed that nB had a near-circular shape with an amorphous structure, a considerably large specific surface area due to nanoparticulation. Additionally, nB possessed a rapid acid buffering capacity, which was comparable to that of μB. In the remineralization test, faster recovery of mechanical properties was observed on the enamel surface immersed in samples containing bioactive glass nanoparticles (nB and nBZ). After remineralization, demineralized enamel immersed in any of the samples showed a rough and porous surface structure covered with mineralized structures. Furthermore, nBZ exhibited a broad antibacterial spectrum. Conclusions: These results demonstrated that bioactive glass and zinc oxide nanoparticles have superior demineralization-suppressing and remineralization-promoting effects.

Myocardial ischemia/reperfusion injury (I/R) and the resulting heart failure is one of the main causes of mortality and morbidity worldwide. Camphene has been shown to have anti-inflammatory and hypolipidemic properties, however, its role in the protection of the heart from ischemia and reperfusion has not been investigated. The cardioprotective role of camphene and the mechanism that mediates its action against I/R injury was evaluated in the present study. A single dose of camphene was administered in adult rats prior to ex vivo I/R induction. Infarct size was measured using 2,3,5-triphenyltetrazolium chloride (TTC) staining and cardiomyocyte injury was assessed by determining the release of lactate dehydrogenase (LDH) enzyme. Camphene pretreatment provided significant protection reducing myocardial infarct size and cell death after I/R. The effect was correlated with the activation of antioxidant defense mechanisms, namely CAT, MnSOD, GPx and GR, and reduction of oxidative stress as evidenced by determination of protein carbonylation and GSH/GSSG ratio in cardiomyocytes. The results suggest that camphene can protect the heart against I/R injury by maintaining redox homeostasis and can hold therapeutic potential for mitigating the detrimental effects of I/R in the heart.

Chemical warfare agents (CWAs) are one of the most toxic compounds. Degradation of CWAs using decontamination agents is one of the few ways to protect human health against the harmful effects of CWAs. A ferrate Fe(VI) based potential chemical warfare agent decontaminant was studied for degradation of persistent nitrogen mustard (tris(2-chloroethyl)amine, HN3). By optimizing the reaction conditions, the complete degradation of HN3 was achieved in 4 minutes. The degradation products contained mostly reduced Fe species which confirmed the environmental friendliness of the proposed decontamination solution.

In this paper, we propose, implement, and test two novel downlink LTE scheduling algorithms. The implementation and testing of these algorithms were in Matlab, and they are based on the use of Reinforcement Learning, more specifically, the Qlearning technique for scheduling two types of users. The first algorithm is called a Collaborative scheduling algorithm, and the second algorithm is called a Competitive scheduling algorithm. The first type of the scheduled users is the Primary Users, and they are the licensed subscribers that pay for their service. The second type of the scheduled users is the Secondary Users, and they could be unlicensed subscribers that dont pay for their service, device to device communications, or sensors. Each user whether it is a primary or secondary is considered as an agent. In the Collaborative scheduling algorithm, the primary user agents will collaborate in order to make a joint scheduling decision about allocating the resource blocks to each one of them, then the secondary user agents will compete among themselves to use the remaining resource blocks. In the Competitive scheduling algorithm, the primary user agents will compete among themselves over the available resources, then the secondary user agents will compete among themselves over the remaining resources. Experimental results show that both scheduling algorithms converged to almost ninety percent utilization of the spectrum, and provided fair shares of the spectrum among users.

The incidence of gastrointestinal diseases (cancer in particular) has increased progressively with considerable morbidity, mortality, and a high economic impact on the healthcare system. Dietary intake of natural bioactive phytochemicals showed to have cancer-preventing and therapeutic effects. This includes the cruciferous vegetable derivative phenethyl isothiocyanate (PEITC), a bioactive compound from watercress. PEITC antioxidant, anti-inflammatory and anti-cancer properties are of particular importance. This review summarizes the current knowledge on the role of PEITC as a potential natural nutraceutical or an adjuvant against oxidative/inflammatory-related disorders in the gastrointestinal tract. We also discuss the safe and recommended dose of PEITC. Besides, we establish a framework to guide the research and development of sustainable methodologies for obtaining and stabilizing this natural nutraceutical for industrial use. This is a topic that still needs more scientific development, but with the potential to lead to a viable strategy in the prevention of cancer and other associated diseases of the gastrointestinal tract.

"The wisdom of crowd'' is so often observed in social discourses and activities around us. The manifestations of it are, however, so intrinsically embedded and behaviorally accepted that an elaboration of a social phenomenon evidencing such wisdom is often cheered as a discovery; or at least an astonishing fact. One such scenario is explored here, namely conceptualization and modeling of a food safety system, a system directly related to social cognition. Food safety is an area of concern these days. Models representing the food safety systems are recently published to study the effect of interactions between important entities of the system. For example, Knowles’s model finds conditions leading to a more efficient and dependable system of entities like consumers, regulators and stores with specific focus on regulators behavior and their impact on the food safety. The first contribution of this paper is reevaluation of Knowles’s model towards a more conscious understanding of ``the wisdom of crowd'' effects on inspection and consuming behaviors. The second contribution is augmenting of the model with social networking capabilities, which acts as a medium to spread information about stores and help consumers find stores which are not contaminated. Simulation results reveal that stores’ respecting social cognition improve effectiveness of the food safety system for consumers and stores both. Simulation findings also reveals that an active society has a capability to self-organize effectively even in the absence of any regulatory compulsion.

Aim: Nepal’s medicinal plants are culturally important and have diverse benefits. Senna alata belongs to the family Leguminosae and is a valuable plant utilized for medicinal and ornamental purposes. The aim of the research was to extract Senna alata leaves by successive maceration with various solvents. Methods: In this study, various methods were utilized to evaluate phytochemistry, overall phenolic and flavonoid content, in-vitro antioxidant, anti-inflammatory, cytotoxicity assay, anti-thrombolytic activity, and antibacterial activities. Results: The extractive values of Senna alata were determined as 1.58%, 0.78%, and 5.92% in hexane, ethyl acetate, and methanol, respectively. GC-MS analysis revealed major compounds such as 3-Methylmannoside, Neophytadiene, Campesterol, and Vitamin E in the leaf extract. Qualitative phytochemical screening verified the tannin content, carbohydrates, flavonoids, cardiac glycosides, glycosides, and saponins in the methanol extract. The total phenolic and flavonoid values were 46.36±4.5 mg GAE/gm and 480.4±3.055 QE/gm of dried extract, respectively. The extract exhibited significant antioxidant and anti-inflammatory activities, with IC50 values of 29.81 and 9.93, respectively. Furthermore, it demonstrated cytotoxic activity with an LC50 value of 767.85 in the brine shrimp bioassay. In terms of thrombolytic activity, the extract showed clot lysis percentages of 7.89% and 10.13% at concentrations of 10 mg/ml and 25 mg/ml, respectively. Conclusion: In conclusion, the methanolic extract of Senna alata leaves displayed therapeutic potential, including antioxidant, anti-inflammatory, cytotoxic, thrombolytic, and antibacterial effects. The existence of several chemicals via GC-MS analysis also verified plant's potential for therapeutic use.

The development of magnesium calcium phosphate bone cements (MCPCs) have garnered big attention. MCPCs are bioactive and biodegradable and have appropriate mechanical and antimicrobial properties for use in reconstructive surgery. In this study, the cement powders based on a (Ca + Mg)/P = 2 system doped with Zn2+ at 0.5 and 1.0 wt.% were obtained and investigated. After the mixing with a cement liquid, structural and phase composition, morphology, chemical structure, setting time, compressive strength, degradation behavior, solubility, antibacterial activities, and in vitro behaviour of the cement materials were examined. A high compressive strength of 48 ± 5 MPa (mean ± SD) was achieved for the cement made from Zn2+ 1.0-wt.%-substituted powders. The Zn2+ introduction led to antibacterial activity against Staphylococcus aureus and Escherichia coli strains, with an inhibition zone diameter up to 8 mm. Biological assays confirmed that the developed cements are cytocompatible and promising as a potential bone substitute in reconstructive surgery.

Products derived from Cannabis sativa have gained increased interest and popularity. As these products become common amongst the public, the heath and potential therapeutic values associated with hemp have become a premier focus of research. While the psychoactive and medicinal properties of Cannabis products have been extensively highlighted in literature, the antibacterial properties of CBD have not been explored in depth. This research serves to examine the antibacterial potential of CBD against Salmonella newington and Salmonella typhimurium. In this study we observed bacterial response to CBD exposure through biological assays, bacterial kinetics, and fluorescence microscopy. Additionally, comparative studies between CBD and ampicillin were conducted against Salmonella typhimurium and Salmonella newington to determine comparative efficacy. Furthermore, we observed potential resistance development of our Salmonella spp. against CBD treatment.

The current research work illustrates an economic and rapid approach towards biogenic synthesis of silver nanoparticles using aqueous Punica granatum leaves extract (PGL-AgNPs). The optimization of major parameters involved in the biosynthesis process was done using Box-Behnken Design (BBD). The effects of different independent variables (parameters) namely concentration of AgNO3, temperature and ratio of extract to AgNO3on response viz. particle size and polydispersity index were analyzed. As a result of experiment designing, 17 reactions were generated which were further validated experimentally. The statistical and mathematical approaches were employed on these reactions in order to interpret the relationship between the factors and responses. The biosynthesized nanoparticles were initially characterized by UV-vis spectrophotometry followed by physicochemical analysis for determination of particle size, polydispersity index and zeta potential via dynamic light scattering (DLS), SEM and EDX studies. Moreover, the determination of functional group present in the leaves extract and PGL-AgNPs was done by FTIR. Antibacterial and antibiofilm efficacies of PGL-AgNPs against Gram-positive and Gram-negative bacteria were further determined. The physicochemical studies suggested that PGL-AgNPs were round in shape and of ~ 37.5 nm in size with uniform distribution. Our studies suggested that PGL-AgNPs exhibit potent antibacterial, and antibiofilm properties.

The study explores antibacterial, antiinflammatory and cytoprotective capacity of Pelargonium sidoides DC root extract (PSRE) and proanthocyanidin fraction from PSRE (PACN) under conditions characteristic for periodontal disease. Following previous finding that PACN exerts stronger suppression of Porphyromonas gingivalis compared to the effect on commensal Streptococcus salivarius, the current work continues antibacterial investigation on Staphylococcus aureus, Staphylococcus epidermidis, Aggregatibacter actinomycetemcomitans and Escherichia coli. PSRE and PACN are also studied for their ability to prevent gingival fibroblast cell death in the presence of bacteria or bacterial lipopolysaccharide (LPS), to block LPS- or LPS+IFNγ-induced release of inflammatory mediators, gene expression and surface antigen presentation. Both PSRE and PACN were more efficient in suppressing Staphylococcus and Aggregatibacter compared to Escherichia, prevented A. actinomycetemcomitans- and LPS induced death of fibroblasts, decreased LPS-induced release of interleukin 8 and prostaglandin E2 from fibroblasts and IL-6 from leukocytes, blocked expression of IL-1β, iNOS, and surface presentation of CD80 and CD86 in LPS+IFNγ-treated macrophages, and IL-1β and COX-2 expression in LPS-treated leukocytes. None of the investigated substances affected either the level of secretion or expression of TNFα. In conclusion, PSRE, and especially PACN, possess strong antibacterial, antiinflammatory and gingival tissue protecting properties under periodontitis mimicking conditions and are suggestable candidates for treatment of the disease.

Many wounds are unresponsive to current available treatment techniques and therefore there is an immense need to explore suitable materials including biomaterials, which are being considered as the crucial factor to accelerate the healing cascade. In this study, we fabricated polyhydroxyalkanoate based antibacterial mats via electrospun technique. One-pot green synthesized graphene decorated silver nanoparticles (GAg) were incorporated into the fibres of poly-3 hydroxybutarate-co-12 mol% hydroxyhexanoate (P3HB-co-12mol% HHx), a co-polymer of polyhydroxyalkanoate (PHA) family which is highly biocompatible, biodegradable and flexible in nature. The synthesised PHA/GAg biomaterial was characterized by field emission scanning electron microscopy (FESEM), elemental mapping, thermogravimetric analysis (TGA), UV-visible spectroscopy (UV-vis) and Fourier transform infrared spectroscopy (FTIR). In-vitro antibacterial analysis were performed to investigate the efficacy of PHA/GAg against gram positive Staphylococcus aureus (S.aureus) strain 12600 ATCC and gram negative Escherichia coli (E.coli) strain 8739 ATCC. The results indicated that the PHA/GAg demonstrated significant reduction of Staphylococcus aureus (S.aureus strain 12600 ATCC) and Escherichia coli (E.coli strain 8739 ATCC) as compared to bare PHA or PHA-rGO in 2 hours of time. The P value (P< 0.05) was obtained by using 2 sample T-test distribution.

Emergence of more virulent forms of human pathogenic bacteria with multi drug resistance is a serious global issue and requires alternative control strategies. The current study was focused to investigate the antibacterial and antibiofilm potential of ferulic acid grafted chitosan (CFA) against Listeria monocytogenes (LM), Pseudomonas aeruginosa (PA), and Staphylococcus aureus (SA). The present result showed that CFA at 64 µg/mL concentration exhibit bactericidal action against LM and SA (>4 log reduction) and bacteriostatic action against PA (<2 log CFU) within 24 h of incubation. Further studies based on propidium iodide uptake assay, measurement of material released from the cell, and electron microscopic analysis revealed that the bactericidal action of CFA was due to the altered membrane integrity and permeability. CFA dose-dependently inhibited biofilm formation (52-89% range), its metabolic activity (30.8-75.1% range) and eradicated mature biofilms, and reduced viability (71-82% range) of the test bacteria. Also, the swarming motility of LM was differentially affected at sub-MIC concentration of CFA. In the present study, the ability of CFA to kill and alter the virulence production in human pathogenic bacteria will insight a new scope for the application of these biomaterials in healthcare to effectively treat bacterial infections.

Nitric oxide (NO) is involved in physiological processes, including vasodilatation, wound healing and antibacterial activities. As NO is a free radical, designing drugs to generate therapeutic amounts of NO in controlled spatial and time manners is still a challenge. In this study, the NO donor S-nitrosoglutathione (GSNO) was incorporated into the thermoresponsive Pluronic F-127 (PL) - chitosan (CS) hydrogel, with an easy and economically feasible methodology. CS is a polysaccharide with known antimicrobial properties. Scanning electron microscopy, rheology and differential scanning calorimetry techniques were used for hydrogel characterization. The results demonstrated that the hydrogel has a smooth surface, thermoresponsive behavior and good mechanical stability. The kinetics of NO release and GSNO diffusion from GSNO-containing PL/CS hydrogel demonstrated a sustained NO/GSNO release, in concentrations suitable for biomedical applications. The GSNO-PL/CS hydrogel demonstrated a concentration-dependent toxicity to Vero cells, and antimicrobial activity to Pseudomonas aeruginosa (minimum inhibitory concentration and minimum bactericidal concentration values of 0.5 µg·mL^-1 of hydrogel, which corresponds to 1 mmol·L^-1 of GSNO). Interestingly, the concentration range in which the NO-releasing hydrogel demonstrated an antibacterial effect was not found to be toxic to the Vero mammalian cell. Thus, the GSNO-PL/CS hydrogel is a suitable biomaterial for topical NO delivery applications.

Oxidative stress initiates and facilitates the disruption of the structural integrity of hepatic mitochondria, which leads to steatosis, steatohepatitis, fibrosis, and cirrhosis. It is now evident that mitochondrial dysfunction could be responsible for alcoholic liver disease (ALD). The challenge in treating ALD has been the limited availability of hepatoprotective agents and the lack of highly efficient delivery systems. Recent studies have shown that mitochondria-targeted therapies could address mitochondrial dysfunction (MD), which may greatly improve hepatoprotection and ALD treatment. This mini-review discusses the potential role of mitochondria-targeted antioxidants (MTAs) in the maintenance of hepatocellular integrity. This report also considers the mechanism of liver injury induced by alcohol and the progression of ALD from a mitochondrial oxidative damage perspective as well as the possible mechanistic actions of hepatoprotective antioxidants. Preliminary studies suggest the prospect of MTAs as anti-ALD and hepatoprotective agents.

A testable theoretical model is presented, proposing which brain parts and mechanisms are responsible for the nature and the nurture components of all human sexual orientations. The model integrates observations from humans and a wide range of animals. If validated, the model would provide a proximate explanation of the biological substrates of all sexual orientations. The basic assumptions of the model are: (1) Children learn automatically and subconsciously in non-sexual conditioning experiences cues for recognizing sexual mates. That skill emerges at puberty. (2) Adults in the child’s surroundings act as innocuous, unaware role-models that provide the learned cues for recognizing mates. (3) Voices of men and women serve as the innate, primary unconditioned stimuli (US) in that learning process. (4) The hypothalamus is the main area that elicits the signals of the unconditioned responses (UR). Those signals trigger the learning of the associated conditioned stimuli (CS) broadcasted by the role-models. (5) The amygdala, base nuclei of the Stria Terminalis (bnST) and hypothalamus play in humans similar roles to those they play in the other species. (6) The human medial geniculate nucleus (MGN) plays the roles played by the olfactory bulbs in rodents. (7) Detectors of innate primary US and activators of the unconditioned sexual responses (UR) are located in the MGN, Amygdala, bnST and Hypothalamus Axis (MASHA). The learned conditioned stimuli (CS) are recorded in the MASHA and in cortical areas. (8) The innate US-UR connections vary across three groups of children. In the first group, only men’s voices trigger the UR. In the second group, only women’s voices trigger the UR, and in a third group each voice can trigger the UR. That determines the learned cues. The first group will be attracted at puberty only to men, the second only to women, and the third group to both.

For the task planning problem of the command and control architecture, the existing algorithms have problems such as low efficiency and poor re-planning quality under abnormal conditions. Based on the requirements of the current accusation architecture, this paper constructs a distributed command and control architecture model based on multi-agents, which makes use of the superiority of multi-agents in dealing with complex tasks. The concept of MultiAgents-HTN is proposed under the framework. The original hierarchical task network planning algorithm is optimized, the multi-agent collaboration framework is redefined, and the coordination mechanism of local conflict is designed. Taking the classical resource scheduling problem as the experimental background, the comparison between the proposed algorithm and the classical HTN algorithm is carried out. The experimental results show that the proposed algorithm has higher quality and higher efficiency than the existing algorithm, and the space anomaly is heavy during processing. The planning is more efficient, and the time is more complicated and superior in dealing with the same problem, with good convergence and adaptability. The conclusion proves that the distributed command and control architecture proposed in this paper has high practicability in related fields and can solve the problem of distributed command and control architecture in multi-agent environment.

Green synthesis using plant extracts has emerged as an eco-friendly, clean, and viable strategy alternative to chemical and physical approaches. The leaf, stem, and root extracts of Lannea discolor was utilized as a reducing and stabilizing agent in the synthesis of gold (AuNPs) and copper (CuNPs) nanoparticles. The formation of AuNPs and CuNPs confirmed by their color change, was characterised by UV–Vis Spectroscopy (UV- Vis), Scanning electron microscopy analysis and energy dispersive x-ray (SEM-EDX), Transmission Electron Microscopy (TEM), and Fourier Transform Infrared Spectroscopy (FTIR), coupled with minimum concentration inhibitory (MIC) antibacterial assays. AuNFs, NPs and CuNPs peaked at wavelengths in the ranges of 316, 544 and 564 nm respectively. TEM showed unexpected nanoflowers (30 – 97 nm) in the leaf extracts and spherical NPs (10 -33 nm; 9.3 – 37.5) from stem and root extracts, while spherical CuNPs (20 – 104 nm), were observed from all the extracts. EDX was able to confirm the presence of metal salts and FTIR revealed stable capping agents. AuNPs and NFs from L. discolor extracts showed appreciable antibacterial activity against Staphylococcus aureus, Escherichia coli, Pseudomonas aeruginosa, Klebsiella pneumoniae and Bacillus subtilis, when compared to the plant extracts, while none was observed from the CuNPs. These AuNPs and CuNPs are particularly appealing in a variety of applications in the biomedical as well as conductivity manufacturing, due to their shapes and sizes and economical and environmentally friendly production.

The biological synthesis of nanoparticles has been emerging as an environmentally benign and eco-friendly method owing to its cost-effectiveness and high efficiency. Recently, the biological synthesis of semiconductor and metal-doped semiconductor nanoparticles with enhanced photocatalytic degradation efficiency and anticancer and antibacterial properties have gained tremendous attention. In pursuit of this purpose, for the first time, we biosynthesized zinc oxide (ZnO) and silver/ZnO nanocomposites (NCs) as semiconductor and metal-doped semiconductor nanoparticles, respectively, using the cell-free filtrate (CFF) of Lysinibacillus sphaericus bacterium. The biosynthesized ZnO and Ag/ZnO were characterized by various techniques such as ultraviolet-visible spectroscopy, X-ray diffraction, Fourier-transform Infrared spectroscopy, Field-emission scanning electron microscopy, transmission electron microscopy, and photoluminescence spectroscopy. The photocatalytic degradation potential of these semiconductor/metal-semiconductor nanoparticles was evaluated against the degradation of azo dye methylene blue (MB) under simulated solar irradiation. Ag/ZnO showed 90.7 ± 0.91% photocatalytic degradation of MB, compared to 50.7 ± 0.53% by ZnO in 120 min. The cytotoxicity of ZnO and Ag/ZnO on human cervical HeLa cancer cells was determined using an MTT assay. Both nanomaterials exhibited cytotoxicity in a concentration-dependent and time-dependent manner on HeLa cells. The antibacterial activity was also determined against Gram-negative (Escherichia coli) and Gram-positive (Staphylococcus aureus). Compared to ZnO, Ag/ZnO NPs showed higher antibacterial activity. Hence, the biosynthesis of semiconductor nanoparticles could be a promising strategy for developing hybrid metal/semiconductor nanomaterials for different biomedical and environmental applications.

Antimicrobial resistance is on the rise, and there aren't enough new treatments to combat it. This might send the modern world back to the pre-antibiotic age. The molecular hybrids of pyrazolo[3,4-b]pyridine and triazole have been designed, synthesized, and analyzed for their drug-like molecule nature and in vitro analyses for their inhibition potentials against S. Aureus and K. Pneumoniae. The compounds CY-R2-25 and CY-R2-28 have been identified as the high potential molecules in this series based on in vitro experiments. CY-R2-25 has zone of inhibition values of 15 0.82 and 14 0.7, whilst CY-R2-28 has the zone of inhibition values of 18 0.95 and 16 0.82 against S. Aureus and K. Pneumoniae, respectively. MIC and MIB values for CY-R2-25 and CY-R2-28 against S. Aureus and K. Pneumoniae are 0.25 and 0.5, respectively.

This work emphasizes to use silver decorative method to enhance the antibacterial activity of TiO₂ and ZnO nanoparticles. These silver decorated nanoparticles (hybrid nanoparticles) were synthesized by using sodium borohydride as a reducing agent, with the weight ratio of Ag precursors: oxide nanoparticles = 1: 30. The morphology and optical property of these hybrid nanoparticles were investigated using transmission electron microscopy (TEM) and UV–vis spectroscopy. The agar-well diffusion method was used to evaluate their antibacterial activity against both Staphylococcus aureus and Escherichia coli bacteria, with or without light irradiation. The TEM images indicated clearly that silver nanoparticles (AgNPs, 5-10 nm) were well deposited on the surface of nano-TiO₂ particles (30-60 nm). Besides, smaller AgNPs (< 2 nm) were dispersed on the surface of nano-ZnO particles (20-50 nm). UV-vis spectra confirmed that the hybridization of Ag and oxide nanoparticles led to shift the absorption edge of oxide nanoparticles to the lower energy region (visible region). The antibacterial tests indicated that both oxide pure nanoparticles did not exhibit inhibitory against bacteria, with or without light irradiation. However, the presence of AgNPs in their hybrids, even at low content (< 40 mg/mL) leads to a good antibacterial activity and the higher inhibition zones under light irradiation as compared to that in dark was observed.

Systems Engineering is an ubiquitous discipline of Engineering overlapping industrial, chemical, mechanical, manufacturing, control, software, electrical, and civil engineering. It provides tools for dealing with the complexity and dynamics related to the optimisation of physical, natural, and virtual systems management. This paper presents a review of how multi-agent systems and complex networks theory are brought together to address Systems Engineering and management problems. The review also encompasses current and future research directions both for theoretical fundamentals and applications in Industry. This is made by considering trends such as mesoscale, multiscale, and multilayer networks; along with the state-of-art analysis on network dynamics and intelligent networks. Critical and smart infrastructure, manufacturing processes, and supply chain networks are instances of research topics for which this literature review is highly relevant.

Copper oxide nanoparticles (CuONPs) were synthesized using an eco-friendly method and their antimicrobial and biocompatibility properties were determined. The supernatant and extract of the fungus Ganoderma sessile yielded small, quasi-spherical NPs with an average size of 4.5 ± 1.9 nm and 5.2 ± 2.1 nm, respectively. CuONPs showed antimicrobial activity against Staphylococcus aureus, Escherichia coli and Pseudomonas aeruginosa. Minimum inhibitory concentration (MIC) for E. coli and S. aureus was 15.9 µg/mL for nanoparticles (NPs) using the supernatant (CuONPs-S) and 16.5 µg/ml for NPs using the extract (CuONPs-E). Lower concentrations were required for P. aeruginosa inhibition. Ultrastructural analysis revealed the presence of the small CuONPs all through the bacterial cells. Finally, the toxicity of CuONPs was analyzed in three mammalian cell lines: hepatocytes (AML-12), macrophages (RAW 264.7) and kidney (MDCK). Low concentrations (<15 µg/ml) of CuONPs-E were non-toxic to kidney cells and macrophages, and the hepatocytes were the most susceptible to CuONPs-S. The results obtained suggest that the CuONPs synthesized using the extract of the fungus G. sessile, could be further evaluated for the treatment of superficial infectious diseases.

Antibiotics have become a widely used drug classes worldwide. Its indiscriminate use in the clini-cal-hospital environment ended up causing antibiotic-resistance genes. Pharmaceutical technology is an essential ally for new formulation development in the antibacterial field. Cyclodextrins (CDs) are ap-proaches that can potentially improve the effectiveness of antibacterial drugs. Thus, this study aimed to review experimental models using CDs as inclusion complexes to improve antibacterial drugs’ physi-cochemical characteristics and biological activities. The review was carried out using the three online journals database PubMed, Scopus, and Embase, limited to Medical Subjects Headings Index. The search protocol was registered in the Open Science Framework database. The following terms and their com-binations were used: cyclodextrins and antibacterial agents in title or abstract, and a total of 1580 studies were identified in a period up to October 2022. Finally, 27 articles were selected for discussion in this review. The biological results reveal that the antibacterial effect of the compounds, complexed with CDs, was extensively improved when compared to the free drugs. CDs can improve the therapeutic effects of antibiotics, already existing on the market, natural products, and synthetic molecules. Therefore, these inclusion complexes using CDs increase the new pharmaceutical products development for clinical ap-plication.

Ticks are key vectors of some important diseases of humans and animals. Although they are carriers of disease agents, the viability and development of ticks are not harmed by the infectious agents due to their innate immunity. Antimicrobial peptides directly protect hosts against pathogenic agents such as viruses, bacteria, and parasites. Among the identified and characterized antimicrobial peptides, defensins have been considerably well studied. Defensins, which contain intramolecular disulfide bridges between cysteine residues, are commonly found among fungi, plants, invertebrates, and vertebrates. The sequence of the tick hemolymph defensin (HEdefensin) gene from the hard tick Haemaphysalis longicornis was analyzed after identification and cloning from a cDNA library. HEdefensin has a predicted molecular mass of 8.15 kDa and a theoretical isoelectric point of 9.48. Six cysteine residues were also identified in the amino acids. The synthetic HEdefensin peptide only showed antibacterial activity against Gram-positive bacteria such as Micrococcus luteus. A fluorescence propidium iodide exclusion assay also showed that HEdefensin increased the membrane permeability of M. luteus. Additionally, an indirect fluorescent antibody test showed that HEdefensin binds to M. luteus. These results suggested that HEdefensin strongly affects the innate immunity of ticks against Gram-positive bacteria.