The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

Mechanical properties of cardiomyocytes from different transmural regions are heterogeneous in the left ventricular wall. The cardiomyocyte mechanical environment affects this heterogeneity because of mechano-electric feedback mechanisms. In the present study, we investigated the effects of load upon transmural differences in contraction of subendocardial (ENDO) and subepicardial (EPI) single cells isolated from the murine left ventricle. Various loads were applied to the cells using carbon fiber techniques for single myocytes. To simulate experimentally obtained results and to predict mechanisms underlying the cellular response to change in load, our mathematical models of the ENDO and EPI cells were used. Extent of the transmural gradient in the time course of contractions was independent of the loading conditions where unloaded and heavy loaded (isometric) contractions were examined, but the regional gradient of the relaxation time characteristics tended to decrease when the load decreased. Under auxotonic contractions, time to peak contraction (T_max) was significantly longer in ENDO cells than in EPI cells at low preload. An increase in preload (axial stretch) prolonged T_max in both cell types; however, the prolongation was greater in EPI cells, resulting in a decrease in transmural gradient in T_max at high preload. The [Ca²⁺]_i transient decay time constant was consistent with the greater preload dependency in T_max of EPI cells. Our modified mathematical models reproduced experimental results, suggesting that differences in cooperativity of cross bridges and calcium troponin C complex interactions between the ENDO and EPI cardiomyocytes may contribute to the different cellular responses to stretch, which may provide a decrease in transmural dispersion of cellular shortening in the intact heart.

Displacement mapping is a computer graphics technique that enables the design of components with regularly or randomly textured surfaces that can be quickly materialized on a three-dimensional (3D) printer when needed. This approach is in principle more flexible, faster and more economical compared to conventional texturing methods, but the accuracy of the texture depends heavily on the parameters used. The purpose of this study is to demonstrate how to produce a surface-textured part using polygonal (mesh) modeling software and a photopolymerizable resin, and to develop a universal methodology to predict the dimensional accuracy of the model file log combined with a resin 3D printer. The printed components were characterized on a scanning confocal microscope. In the setup used in this study, the mesh size had to be reduced to 10% of the smallest feature size and the textured layer had to be heavily (x4) overexposed to achieve the desired accuracy. As a practical application, two functional stamps with a regular (honeycomb) and a random texture, respectively, were successfully manufactured. The insights gained will be of great benefit in quickly and cost-effectively producing components with innovative patterns and textures for a variety of hobby, industrial and biomedical applications.

The impact of systemic vascular resistance (SVR) in hypertrophic (HCM) and amyloid cardio-myopathies has been seldom investigated. We studied pressure-strain loop derived myocardial work (MW) indices and SVR in patients with either sarcomere HCM or wild type transthyretin cardiac amyloidosis (ATTR), presented with heart failure and preserved left ventricular ejection fraction (HFpEF) at the outpatient cardiology units at Messina and Catania University Hospitals (Italy). Patients were in sinus rhythm and needed to have good transthoracic ultrasound imaging quality to undergo transthoracic strain-echocardiography. Other than conventional parameters, SVR and GWI (global work index) were measured. Based on cross-tabulation (a way to assess the ventricular-arterial coupling), the patients were then classified in 4 classes according to the cut-off values suggested by previous studies of 1,440 dyne/s/cm-5 for SVR (Stefadouros et al., 1973) and 1576 mm Hg% for GWI (Olsen et al., 2022). Sixty patients, 30 in each group, aged 61±16 years, 78% males, were studied. HCM were younger than ATTR patients and in a better clinical status (23% HCM vs 77% ATTR were NYHA class 3, p<0.001). Overall, 51 patients (85%) showed high SVR, of whom 21 were HCM (70%) and 30 ATTR (100%) (p<0.005). Both, SVR and GWI were impaired (the poorest class C) in 43% HCM patients (with greater left ventricular concentric hypertrophy) vs 93% of ATTR patients (in advanced NYHA class) (p<0.001). In conclusion, assessing SVR and GWI in HFpEF patients with HCM or ATTR can help clinicians to interpret the pathophysiological and clinical features of such complex diseases.

Any quantization maps linearly functions on a phase space to symmetric operators in a Hilbert space. Covariant integral quantization combines operator-valued measure with symmetry group of the phase space. Covariant means that the quantization map intertwines classical (geometric operation) and quantum (unitary transformations) symmetries. Integral means that we use all ressources of integral calculus, in order to implement the method when we apply it to singular functions, or distributions, for which the integral calculus is an essential ingredient. In this paper we emphasize the deep connection between Fourier transform and covariant integral quantization when the Weyl-Heisenberg and affine groups are involved. We show with our generalisations of the Wigner-Weyl transform that many properties of the Weyl integral quantization, commonly viewed as optimal, are actually shared by a large family of integral quantizations.

Aim: To analysis the relationship between healthy adults right ventricular diameter (RVD) and geographical factors. Location: China’s 22 provinces, municipalities and autonomous regions. Methods: Using correlation analysis the relationship between RVD and nine geographic factors, build predictive models by factor analysis. Results: There is significant correlation between RVD and geographical factors, and the annual average temperature is most relevant geographical factors, a predictive model was built by factor analysis: Ŷ = 19.46 + 0.0007072X1 + 0.001034X2 -0.05412X3 -0.001405X4 -0.0006351X5 + 0.02903X6 + 0.01243X7 -0.01033X8 + 0.03816X9 ± 0.63. Then using Kriging interpolation interpolate the geographical distribution of Chinese healthy adult right ventricular diameter reference value in ArcGIS software. Main Conclusion: If geographic factors can be derived in anywhere of China, RVD can be calculated by the model, you can also get RVD from geographical distribution.

A century-old scientific conundrum is solved in this paper. The Prandtl mixing length modelled plane boundary turbulent flow is described by: $\frac{du^+}{d{y^+} }+\kappa^2{y^+} ^2\left( \frac{du^+}{d{y^+} }\right)^2=1$, together with boundary condition $ {y^+} =0:\, u^+=0$. Only an approximate solution to this nonlinear ordinary differential equation (ODE) has been sought so far, however, the exact solution to this ODE has not been obtained. By introducing a transformation, $2\kappa y^+=\sinh \xi$, I successfully find the exact solution of the ODE as follows: $u^+=\frac{1}{\kappa}\ln(2\kappa {y^+} +\sqrt{1+4\kappa^2{y^+} ^2})-\frac{2{y^+} }{1+\sqrt{1+4\kappa^2{y^+} ^2}}$.

We propose a method for creating parallel Bessel-like vortical optical needles with an arbitrary axial intensity distribution via superposition of different cone-angle Bessel vortices. We analyze the interplay between the separation of individual optical vortical needles and their respective lengths and introduce a super-Gaussian function as their axial profile. We also analyze the physical limitations to observe well-separated optic needles, as they are influenced by mutual interference of the individual beams. To verify our theoretical and numerical results, we generate controllable spatial arrays of individual Bessel beams with various numbers and spatial separations by altering the spectrum of the incoming laser beam via the spatial light modulator. We demonstrate experimentally how to implement such beams using a diffractive mask. The presented method facilitates the creation of diverse spatial intensity distributions in three dimensions, potentially finding applications in specific microfabrication tasks or other contexts. These beams may have benefits in laser material processing applications such as nanochannel machining, glass via production, modification of glass refractive indices, and glass dicing.

Purpose: To simplify the application of optical coherence tomography (OCT) for examination of subsurface morphology in the oral cavity and reduce barriers towards adoption of OCT as a biopsy guidance device. The aim of this work was to develop automated software tools for simplified analysis of the large volume of data collected during OCT. Methods: Imaging and corresponding histopathology were acquired in-clinic using a wide-field endoscopic OCT system. An annotated dataset (n = 294 images) from 60 patients (34 male, 26 female) was assembled to train four unique neural networks. A deep learning pipeline was built using convolutional and modified u-net models to detect the imaging field of view (network 1), detect artifacts (network 2), identify the tissue surface (network 3), and identify the presence and location of the basement membrane (network 4). Results: The area under the curve of the image and artifact detection networks was 1.00 and 0.94 respectively. The Dice similarity score for the surface and basement membrane segmentation networks was 0.98 and 0.83 respectively. Conclusion: Deep Learning (DL) techniques can identify the location and variations in the epithelial surface and basement membrane in OCT images of the oral mucosa. Segmentation results can be synthesized into accessible en face maps to allow easier visualization of changes.

In this paper, we aim to assess the electric current parameters and report the analysis of the associated degree of ventricular recovery during left ventricular assist device (LVAD) support. An assumption was made there is a linear relationship between ventricular recovery degree and the pump electric current pulsatility index (PI). The experimental study was carried out using the ViVitro Pulse Duplicator System with Sputnik 1 LVAD connected. Cardiac output (CO) and cardiac power output (CPO) were used as a measure of ventricular recovery degree. Different heart rates (HR) (59, 73, 86 bpm) and pump speeds (7600–8400 rpm in 200 rpm steps) were investigated. Ventricular stroke volumes in the range of 30–80 ml for each heart rate at certain pump speed were used. The obtained relationships of CO and CPO vs. PI was linear as the coefficients of determination for each regression curve were more than 0.8. CO vs. PI: R2=0.9218; 0.9271; 0.9172 and CPO vs. PI: R2=0.8517; 0.841; 0.8244 for HR=59 bpm; 73 bpm; 86 bpm, respectively. Study findings suggest that adequate interpretation of parameters could potentially serve as a valuable clinical tool to assess ventricular recovery based on LVAD infrastructure without requiring any special hemodynamic assessment.

There are given algebraic and integral identities for a pair or a triple of plane solenoidal fields. As applications, we obtain sufficient potentiality conditions for a plane vector field. The integral identities are also important for exact a priori estimates.

According to the standard cold dark matter (CDM) cosmology, the structure of dark halos including those of galaxy clusters reflects their mass accretion history. Older clusters tend to be more concentrated than younger clusters. Their structure, represented by the characteristic radius $r_s$ and mass $M_s$ of the Navarro-Frenk-White (NFW) density profile, is related to their formation time. In this study, we show that $r_s$, $M_s$, and the X-ray temperature of the intracluster medium (ICM), $T_X$, form a thin plane in the space of $(\log r_s, \log M_s, \log T_X)$. This tight correlation indicates that the ICM temperature is also determined by the formation time of individual clusters. Numerical simulations show that clusters move along the fundamental plane as they evolve. The plane and the cluster evolution within the plane can be explained by a similarity solution of structure formation of the universe. The angle of the plane shows that clusters have not achieved “virial equilibrium” in the sense that mass/size growth and pressure at the boundaries cannot be ignored. The distribution of clusters on the plane is related to the intrinsic scatter in the halo concentration--mass relation, which is originated from the variety of cluster ages. The well-known mass--temperature relation of clusters ($M_\Delta\propto T_X^{3/2}$) can be explained by the fundamental plane and the mass dependence of the halo concentration without the assumption of virial equilibrium. The fundamental plane can also be used for calibration of cluster masses.

A temperature-modulated pyroelectricity measurement system for a small single crystal is developed and applied to standard sample measurements performed on a thin single crystal of lithium niobate. The modulation measurement is based on the AC technique, in which the temperature of the sample is periodically oscillated, and the synchronized pyroelectric signal is extracted using a lock-in amplifier. Temperature modulation is applied by irradiating periodic light on the sample placed in the heat exchange gas. To apply this technique to the transparent reference sample, a commercially available black resin is coated on the sample’s surface to absorb the light energy and transmits it to the specimen. The experimental results are analyzed using a two-layer heat transfer model to verify the effect of the light-absorbing layer as well as the non-contact temperature modulation system.

To solve the problem of complex sensor installation and easy damage in contact displacement measurement, a non-contact measurement method of brace displacement in bridge swivel construction based on binocular vision is proposed in this study. Combined with monitoring data in a swivel construction interchange project, binocular vision system was compared and analyzed with the traditional displacement meter and total station. Results showed that force versus displacement variation plots were obtained by binocular visual measurement in the weighing test, the inflection point can be clearly distinguished, and the position of the inflection point was the same as that of the displacement meter; monitoring data of binocular vision measurement and total station were compared and analyzed in the bridge swivel process, the average error was no more than 0.18 mm, the maximum error was no more than 0.42 mm, and the standard deviation was no more than 0.12. The method proposed in this study can be used as an alternative to displacement meter and total station measurement methods in bridge swivel construction, the problem of complex sensor installation and easy damage is solved in brace displacement measurement, equipment and labor costs can be effectively saved.

This paper describes the optimal design of a miniature fiber-optic linear displacement sensor. It is characterized by its ability to measure displacements along a millimetric range with sub-micrometric resolution. The sensor consists of a triangular reflective grating and two fiber-optic probes. The measurement principle of the sensor is presented. The design of the sensor's triangular grating has been geometrically optimized by considering the step angle of the grating to enhance the sensor's resolution. The optimization method revealed a global optimum at which the highest resolution is obtained

The formulation used by most of the studies on an elastic torus are either Reissner mixed formulation or Novozhilov's complex-form one, however, for vibration and some displacement boundary related problem of a torus, those formulations face a great challenge. It is highly demanded to have a displacement-type formulation for the torus. In this paper, I will carry on my previous work [ B.H. Sun, Closed-form solution of axisymmetric slender elastic toroidal shells. J. of Engineering Mechanics, 136 (2010) 1281-1288.], and with the help of my own maple code, I am able to simulate some typical problems and free vibration of the torus. The numerical results are verified by both finite element analysis and H. Reissner's formulation. My investigations show that both deformation and stress response of an elastic torus are sensitive to the radius ratio, and suggest that the analysis of a torus should be done by using the bending theory of a shell, and also reveal that the inner torus is stronger than outer torus due to the property of their Gaussian curvature. Regarding the free vibration of a torus, our analysis indicates that both initial in u and w direction must be included otherwise will cause big errors in eigenfrequency. One of the most intestine discovery is that the crowns of a torus are the turning point of the Gaussian curvature at the crown where the mechanics' response of inner and outer torus is almost separated.

Structural displacement is an important metric for assessing structural conditions because it has a direct relationship with the structural stiffness. Many bridge displacement measurement techniques have been developed, but most methods require fixed reference points in the vicinity of the target structure which limits field implementations. A promising alternative is to use reference-free measurement techniques that indirectly estimate the displacement by using measurements such as acceleration, and strain. This paper proposes novel reference-free bridge displacement estimation by the fusion of single acceleration with pseudo-static displacement derived from co-located strain measurements. First, we propose a conversion of the strain at the center of a beam into displacement based on the geometric relationship between strain and deflection curves with reference-free calibration. Second, an adaptive Kalman filter is proposed to fuse the displacement generated by strain with acceleration by recursively estimate the noise covariance of displacement from strain measurements which is vulnerable to measurement condition. Both numerical and experimental validations are presented to demonstrate the efficiency and robustness of the proposed approach.

COVID-19 affects many organs in our body, including the heart and lungs. COVID-19 cases that require hospitalization often exhibit pulmonary hypertension (PH) due to changes in the lung microvasculature in which the blood vessels become stiff, damaged, or narrow, causing increased pulmonary arterial pressure. This review examines the hypothesis that PH can lead to right ventricular hypertrophy (RVH) as a long-lasting aftereffect of COVID-19. Recent studies have shown that significant percentages of hospitalized patients develop right ventricular hypertension and right ventricular dilatation (RVD), which may lead to right ventricular failure and death. Despite recommendations for echocardiogram reports to include right ventricular wall thickness to assess RVH, few published reports have reported this parameter. Relevant studies on animal models of PH in which the timing of PH can be precisely controlled suggest that one to three weeks of PH can cause RVH. Thus, according to the hypothesis proposed here COVID-19 patients who have long-lasting severe disease (e.g., needed to be on a ventilator for one or more weeks) accompanied by PH and RVD may develop RVH as a long-lasting sequela outlasting the infection itself. Echocardiogram studies of recovered COVID-19 patients may determine whether oft-reported cardiovascular sequelae include RVH.

Premature ventricular complexes (PVCs) are frequently encountered in clinical practice. The association of PVCs with adverse cardiovascular outcomes in the context of structural heart disease is well established, yet the association between PVCs and cardiovascular outcomes in the absence of structural heart disease is not fully elucidated. Cardiac magnetic resonance (CMR) seems to contribute prognostically in the latter subgroup. PVC- induced myocardial dysfunction refers to the impairment of ventricular function due to the PVCs and is mainly associated with a PVC burden greater than 10%. The surface 12- lead ECG is used to localize the anatomic site of origin and multiple algorithms have been developed to differentiate right ventricular and left ventricular outflow tract (RVOT and LVOT, respectively) origin. Novel algorithms include alternative ECG configurations and lately, sophisticated artificial intelligence methods have been utilized to distinguish the origins of outflow tract arrhythmias. The decision to therapeutically address PVCs should be taken upon the presence of symptoms or the development of PVC- induced myocardial dysfunction. The therapeutic modalities include pharmacological therapy, namely I-C antiarrhythmic drugs and beta blockers, as well as catheter ablation, which demonstrates superior efficacy and safety.

The prevalence and incidence of cardiac pro-arrhythmic disorders are often influenced by sex due to specific effects on the QT interval. Androgens shorten QT, which may be protective against acquired long QT syndromes and their related arrhythmias in men such as torsade de pointes (TdP). On the other hand, androgens can potentiate Brugada and early repolarization syndromes, which are most prevalent in men. In this case series, we highlight four male patients with aborted SCD in the setting of abnormal testosterone status; two patients with TdP in a setting of testosterone deprivation (of which one drug-induced) and 2 patients with ventricular fibrillation associated with exogenous androgenic booster (Tribulus terrestris) intake. From this case series, we review the current available literature of the effects of androgen as a double-edged sword on the QTc interval and emphasize the importance of QTc monitoring in this subset of patients.

: Inflammation may mediate the association of mitral valve prolapse (MVP) with ventricular scarring and arrhythmia. The purpose of this study is to investigate the association of neutrophil- and platelet-to-lymphocyte ratios (NLR, PLR) with ventricular arrhythmia in MVP. Clinical and demographic data were extracted from electronic medical records for all patients aged 18-90 years with MVP on echocardiography between 2016-19 at our institution. We studied 65 patients who had a differential blood count within six months prior to ambulatory ECG (A- ECG) (medi-an age [IQR] 70 [61-77] years; 62% female; 12% African American). Patients with surgery or in-fection within six months prior to CBC were excluded. Complex or frequent ventricular ectopy (cfVE) was defined as the presence of two or more premature ventricular contractions (PVCs) on a 10-second ECG tracing or greater than 1% PVC burden or NSVT on ambulatory ECG monitoring. Logistic and bivariate regression was used to analyze clinical, electrocardiographic and echo-cardiographic factors associated with NLR and PLR. Factors associated with higher NLR were congestive heart failure (p=0.005), male sex (p=0.01), age (p=0.003), and bileaflet MVP (p=0.04). NLR was associated with higher absolute PVC burden (rs=0.28, p=0.03) and cfVE (median NLR [IQR] 3.0 [1.6 – 6.3]) with cfVE versus (2.4 [1.4-3.4], p=0.04) without cfVE. An NLR of 5.6 yielded 50% sensitivity and 90% specificity for PVC burden >1% (AUC 0.69). No significant association was found between PLR and PVC burden or cfVE. NLR is associated with PVC burden and com-plex ventricular ectopy in MVP, suggesting that inflammation is a significant factor in the patho-genesis of ventricular arrhythmia in this condition.

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

Shale gas and coalbed methane are energy sources that partly or even mainly consist of methane stored in an adsorbed state in the pores of the organic-rich rock and coal seams. In this study, the graphene nanoslit model is employed to model the nanometer slit pores in shale and coal. The Grand Canonical Monte Carlo (GCMC) and Molecular Dynamics (MD) modelling methods are used to investigate the mechanisms of adsorption and displacement of methane in the slit pore. It was found that the CVFF forcefield resulted in the largest adsorption amount, while the PCFF forcefield resulted in the least. The COMPASS and COMPASS II force fields led to similar results. As the width of the slit pore increases, the adsorption amount of gas molecules increases, and the number density profile of adsorbed methane molecules alters from a single adsorption layer to multi-adsorption layers. The minimum slit pore width at which methane molecules can penetrate the slit pore was found to be 0.7 nm. Moreover, it is demonstrated that by lowering the temperature, the adsorption rate of the methane increases since the adsorption is an exothermic process. Enhancing methane recovery was investigated by the injection of gases such as CO2 and N2 to displace the adsorbed methane. The comparison of adsorption isotherms of gas molecules provided the following order in terms of the amount of adsorption: CO2&gt;CH4&gt;N2.

Polymer-based composites are widely used in the automotive, security, aeronautical and space industries, to mention a few. This is because of their good mechanical properties, which are similar to those of metals but with the attraction of being lightweight. Kevlar® as a reinforcement is extensively used in the security industry owing to its good ballistic properties. This investigation presents the mechanical characterization based on in-plane quasi-static tensile testing of Kevlar® composite using a universal testing system. The methodology developed for the preparation of coupons is based on pressure, temperature and time. As a result of this work, elastic moduli (EL and ET), Poisson’s ratio (νLT), shear modulus (GLT) and strengths (XT, YT, S) were obtained. It is worth mentioning that there is scarce or no characterization of this material in the literature, and those studies that do characterize it do not present the coupon thermoforming conditions or the reasons of the specimen dimensions (width, length and thickness).

Variable cross-section arch is widely used in practical engineering because of its beautiful arc and excellent mechanical properties. However, there is still no systematic and comprehensive study on the out-plane buckling of variable cross-section arch. In view of this, this paper is concentrated on an elastic analytical research of out-plane buckling of arches with variable cross-section under a uniformly distributed radial local load. The pre-buckling and out-plane buckling behaviour of a variable cross-sectional arch under an external load is quite different from that of an arch with uniform cross-section. The Castigliano's second theorem is used to establish pre-buckling force method equilibrium equations for variable cross-sectional arches under a uniformly distributed radial local load, and corresponding analytical solutions of normal stress, axial compression and the bending moment are obtained. Based on the energy method and the Ritz method, analytical solutions of the critical load for the elastic out-plane buckling of arches with variable cross-section are derived. Comparisons with ANSYS results indicated that the analytical solutions are able to accurately predict the pre-buckling internal forces and critical out-plane buckling load of variable cross-section arches subjected to a uniformly distributed radial local load. It is found that the internal forces and the out-plane buckling load of an arch are significantly affected by the variation of cross-sectional height. With the ratio of cross-sectional height of the top to the end increase, the bending moment decreases and the axial force and critical out-plane buckling load increase. Analytical solutions of pre-buckling internal force and critical out-plane buckling load problems for arches with variable cross-section have a wider significance, since they can provide an effective explicit analytic method for the optimal design of arch structure.

Probability is an open question in the ontological interpretation of quantum mechanics. It has been discussed in some trajectory interpretations such as Bohmian mechanics and stochastic mechanics. New questions arise when the domain of probability extends to the complex space, including the generation of complex trajectories, the definition of the complex probability, the relation of the complex probability to the real quantum probability, and so on. The complex treatment proposed here applies the optimal quantum guidance law to derive the stochastic differential (SD) equation governing the particle’s random motions in the complex plane. The ensemble of the complex quantum random trajectories (CQRTs) solved from the complex SD equation is used to construct the probability distribution ρc(t,x,y) of the particle’s position over the complex plane z=x+iy. The correctness of the obtained complex probability is confirmed by the solution of the complex Fokker-Planck equation. The significant contribution of the complex probability is that it can be used to reconstruct both quantum probability and classical probability, and to clarify their relationship. Although quantum probability and classical probability are both defined on the real axis, they are obtained by projecting complex probability onto the real axis in different ways. This difference explains why the quantum probability cannot exactly converge to the classical probability when the quantum number is large.

We report herein high-resolution x-ray diffraction measurements of basal plane bending of homoepitaxial single-crystal diamond (SCD). The results reveal that growth parameters such as temperature, growth time and basal plane bending of the substrate affect the basal plane bending of SCD. First, the basal plane bending of SCD depends mainly on the substrate itself. The basal plane bending of SCD becomes more severe with increasing basal plane bending of the substrate and this type of basal plane bending cannot be recovered. The SCD growth experiments show that the basal plane bending increases at high temperature and with increasing growth time. Finally, to understand the mechanism behind basal plane bending, we investigate the substrate-surface temperature distribution as a function of basal plane bending of SCD fabricated by chemical vapour deposition (CVD). This allows us to propose a bending model and understand the origin of basal plane bending. The results indicate that an uneven temperature distribution on the substrate surface is the main cause of the CVD diamond base-plane bending.

A focal plane array (FPA) detector was used for hyperspectral imaging in the infrared (IR) spectral region using thermal and synchrotron light sources. FPA Fourier-transform IR (FTIR) imaging microspectroscopy will be able to monitor real time changes at specific absorption bands when combined with high brightness synchrotron source. In this study, several types of samples with unique structural motifs were selected and used for assessing the capability of the FPA-FTIR imaging technique. It was shown that the time required for polariscopy at IR wavelengths can be substantially reduced by the FPA-FTIR imaging approach. By using natural and laser fabricated polymers with sub-wavelength features, alignment of absorbing molecular dipoles was revealed as well as higher order patterns (laser fabricated structures). Micro-spectroscopy of absorber orientation reveals alignment patterns even when they are not spatially resolved.

Coseismic landslides have the potential to cause catastrophic disasters. Thus, it is of crucial importance to conduct a comprehensive regional assessment of susceptibility to coseismic landslides. This study rigorously interprets 13,759 coseismic landslides triggered by the 2022 Luding earthquake within the seismic zone. Employing the Newmark method, we systematically assess the susceptibility to coseismic landslides through the application of six distinct displacement regression models. The efficacy of these models is validated against the actual landslide inventory using the area under the curve. A hazard map of coseismic landslides is generated based on the displacement regression model with the highest degree of fit. The results show that Moxi Town, Detuo Town, the flanks of the Daduhe River, Wandonghe River, Hailuogou River, and Yanzigou River are high susceptibility areas for coseismic landslides. The study explores factors influencing model fit, revealing that the inclusion of both epicentral distance and the distance to seismogenic fault and in displacement prediction enhances model performance. Nevertheless, in close proximity to fault zones, the distance to seismogenic fault exerts a more significant influence on the spatial distribution density of coseismic landslides compared to the epicentral distance. Conversely, in regions situated further from fault zones, the epicentral distance has a greater impact on the spatial distribution density of coseismic landslides compared to the distance to seismogenic fault. These findings contribute to a nuanced understanding of coseismic landslide susceptibility and offer valuable insights for future Newmark method-based coseismic landslide displacement calculations.

CO2 flooding stands as a pivotal technique for significantly enhancing oil recovery in low-permeability reservoirs. The movement and sweeping rules at the front of CO2 flooding play a critical role in its oil recovery, yet a comprehensive quantitative analysis remains an area in need of refinement. In this study, we have developed 1D and 2D numerical simulation models to explore the sweeping behavior of miscible, immiscible, and partly-miscible CO2 flooding patterns. The front position and movement rules of the three CO2 flooding patterns are determined. A novel approach of the contour area calculation method is introduced to quantitatively characterize the sweep coefficients, and the sweeping rules are discussed regarding geological parameters, oil viscosity, and injection-production parameters. Furthermore, the Random Forest (RF) algorithm is employed to identify the controlling factor of the sweep coefficient, as determined by out-of-bag (OOB) data displacement analysis. The results show that the miscible front is located at the point of maximum CO2 content in the oil phase. The immiscible front occurs at the point of maximum interfacial tension near the production well. Remarkably, the immiscible front moves at a faster rate compared to the miscible front. Geological parameters, including porosity, permeability, and reservoir thickness, significantly impact the gravity segregation effect, thereby influencing the CO2 sweep coefficient. Immiscible flooding exhibits the highest degree of gravity segregation, with a maximum gravity segregation degree (GSD) reaching 78.1. The permeability ratio is a crucial factor, with a lower limit of approximately 5.0 for reservoirs suitable for CO2 flooding. Injection-production parameters also play a pivotal role in sweep coefficient. Decreased well spacing and increased gas injection rates are found to enhance sweep coefficients by suppressing gravity segregation. Additionally, higher gas injection rates can improve the miscibility degree of partly-miscible flooding from 0.69 to 1.0. Oil viscosity proves to be a significant factor influencing the sweep coefficients, with high seepage resistance due to increasing oil viscosity dominating the miscible and partly-miscible flooding patterns. Conversely, gravity segregation primarily governs the sweep coefficient in immiscible flooding. In terms of controlling factors, the permeability ratio emerges as a paramount influence, with a factor importance value (FI) reaching 1.04. these results provide a theoretical foundation for the application of CO2 flooding, enhancing the understanding of the critical factors governing its success.

Grating (moiré) interferometry is one of the well-known methods for full-field in-plane displacement and strain measurement. There are many design solutions for grating interferometers, including systems with a microinterferometric waveguide head. This article proposes a modification to the conventional waveguide interferometer head, enabling the implementation of a polarization fringe phase shift for automatic fringe pattern analysis. The article presents both the theoretical consideration of the proposed solution and its experimental verification, along with the concept of the in-plane displacement/strain sensor using the described head.

Background Acute right heart failure (RHF) is associated with high morbidity and mortality. Temporary mechanical circulatory support (tMCS) is now part of the advanced management strategy for refractory cardiogenic shock (CS). Among such support systems, VA-ECMO remains the fastest MCS system to set up. The ProtekDuo cannula can be used as a temporary and percutaneous right ventricular assist device (RVAD) in relay with VA-ECMO in the context of prolonged weaning. Case Summary This case report describes the clinical course of a 69-year-old patient who underwent elective aortic valve replacement surgery complicated by acute RHF due to iatrogenic ligation of the right coronary artery. VA-ECMO was initiated in the context of refractory cardiogenic shock. Faced with prolonged MCS weaning, due to lack of recovery of the right ventricle associated with the absence of any other therapeutic option, a percutaneous RVAD via a ProtekDuo cannula was implanted as a bridge to recovery. The ProtekDuo was gradually weaned while the patient began rehabilitation. The patient was transferred to the medical ward after 5 weeks in the ICU, stayed 5 months in an acute medical setting, went to a rehabilitation center afterward and returned home 6 months after the initial surgery without any neurological sequalae or organ failures. In total, she remained on MCS for 39 days (21 on VA-ECMO and 18 on ProtekDuo). Discussion In cases of refractory RHF, after stabilization and organ perfusion restoration under VA-ECMO, it is feasible to switch to a percutaneous RVAD, allowing early mobilization of patients during prolonged MCS weaning until the right ventricle adapts to new loading conditions.

Abstract-Digital Phase Plane is presented in this paper. For constant input second order digital systems with arbitrary initial conditions for arbitrary quantizaters, this digital phase plane shows, in plot form, the state trajectory and the asymptotic stability, including the existence and the position of arbitrary period limit cycles.

In-plane electro-optical switching (IPS) is a natural feature of a conventional planar aligned display cell based on deformed helix ferroelectric liquid crystal effect (DHFLC-effect) with sub-wavelength helix pitch if the tilt angle close to 40 degrees.

Background: Left ventricular hypertrophy (LVH) may be due to different causes, ranging from benign secondary forms to severe cardiomyopathies. Transthoracic Echocardiography (TTE) and ECG are the first level examination for LVH diagnosis. Cardiac magnetic resonance (CMR) defines accurately LVH type, extent and severity. Objectives: to evaluate the diagnostic and prognostic role of CMR in patients with TTE and/or ECG evidence of LVH. Methods: We performed CMR in 300 consecutive patients with echocardiographic and/or ECG signs of LVH. Results: Overall, 275 patients had TTE evidence of LVH with initial suspicion of hypertrophic cardiomyopathy (HCM) in 132 (44%), cardiac amyloidosis in 41 (14%), hypertensive LVH in 48 (16%), aortic stenosis in 4 (1%), undetermined LVH in 50(16%). The initial echocardiographic diagnostic suspicion of LVH was confirmed in 172 patients (57.3%) and changed in 128 patients (42.7%, p<0.0001): the diagnosis of HCM increased from 44% to 71% of patients; hypertensive and undetermined LVH decreased significantly (respectively to 4% and 5%). CMR allowed a diagnosis in 41 out of 50 (82%) with undetermined LVH at TTE. CMR also identified HCM in 17 out of 25 patients with apparently normal echo but with ECG criteria for LVH. Finally, the reclassification of the diagnosis by CMR was associated with a change of survival risk of patients: after CMR reclassification no events occurred in patients with undetermined or hypertensive LVH. Conclusions: CMR changed echocardiographic suspicion in almost half of patients with LVH. In the subgroup of patient with abnormal ECG, CMR identified LVH (particularly HCM) in 80% of patients. This study highlights the indication of CMR to better characterize the type, extent and severity of LVH detected at echocardiography and suspected with ECG.

Background: Heart failure is a major cause of morbidity and mortality worldwide; left ventricular diastolic dysfunction plays a leading role in this clinical context. Diastolic dysfunction may be predisposed by increased abdominal fat and, consequently, increased pericardial and epicardial adiposity. This study aimed to determine whether pericardial and epicardial fat are associated with left ventricular diastolic function. Methods: 82 patients had their abdominal circumference measured and underwent transthoracic echocardiography to measure the thickness of pericardial and epicardial fat and assess the left ventricular diastolic function. Two groups were created based on mean pericardial fat thickness (4.644 mm) and were related to abdominal circumference and echocardiographic parameters. Results: Subjects in the PF High group showed a significant decrease in septal e' (p&lt;0.0001), lateral e' (p&lt;0.0001) and E/A ratio (p=0.003) and a significant increase in E/e' ratio (p&lt;0. 0001), E wave deceleration time (p=0. 013), left atrial volume (p&lt;0.0001), LV mass (p=0.003), tricuspid regurgitant jet velocity (p&lt;0.0001) and LV diameter (p=0.014) compared to the PF Low group. Conclusions: Measurement of abdominal circumference, pericardial and epicardial fat is an early indicator of diastolic changes with transthoracic echocardiography being the gold standard exam.

The study of velocimetry is important for characterizing and comprehending the effects of fluid flow, and the Particle Image Velocimetry (PIV) technique is one of the primary approaches for understanding the velocity vector field in a test section. Commercial PIV systems are expensive, with one of the main cost factors being high-speed camera equipment capable of capturing images at high frames per second (fps), rendering them impractical for many applications. This study proposes an evaluation of utilizing smartphones as image acquisition systems for PIV technique application. An experimental setup inspired by the known angular displacement of synthetic particles is proposed. A stepper motor rotates a plate containing an image of synthetic particles on its surface. The motion of the plate is captured by the smartphone camera, and the images are processed using PIVlab-MatLab® software. The use of two smartphones is assessed, with acquisition rates of either 240 fps or 960 fps and varying angular velocities. The results were satisfactory for velocities up to 0.7 m/s at an acquisition rate of 240 fps and up to 1.8 m/s at 960 fps, validating the use of smartphones as a cost-effective alternative for the PIV technique.

The holy town of Joshimath, gateway to the India-China border and religious places like Badrinath, Hemkunt Sahab, Valley of flowers in the Uttarakhand state of India experienced cracks in many of the residential and commercial buildings in the month of November-December 2022 which created panic and relocation of people. The reason(s) for the subsidence is still not known but using the InSAR technology and data from Sentinel-1, SAR data for the region was processed using HyP3 and MintPy for January-December 2022 to understand when the phenomenon started and how much uplift/subsidence the area has underwent in the last one year, as no such study is available till today. The entire town can be classified into two zones with respect to the annual subsidence values. Severe subsidence has been observed in the North and East regions whereas most of the southern region experienced moderate to low subsidence. Since the town is built on the debris of an old landslide, the subsidence may be attributed to the change in the course of the underground water channels due to heavy and continuous construction happening in the region and also due to drop in the water table. The results shows that the subsidence in the region was ongoing since June (from January till May, almost negligible vertical movement was recorded) which accelerated after September (when an uplift was recorded which lasted till October), while the subsidence peaked in the month of December with recorded subsidence of as much as 10 cm in some areas located around the Joshimath town, where most of the residential and commercial buildings are located.

(1) Background: The mediolateral patella displacement is of interest for diagnostics and clinically relevant research questions. Apart from manual testing, no standardized method is currently available. Proper quantification of patella mobility is necessary to understand pathologies at the patellofemoral joint better; (2) Methods: Patella mobility was assessed in 25 healthy individuals using a Patellostabilometer, a new prototype instrument for quantification of the mediolateral patella displacement. The participants underwent measurements of the mediolateral displacement three times using the Patellostabilometer. A maximal force of 10N was applied for patella movement. Additionally, leg length, circumference of the knee, upper- and lower leg was measured. (3) Results: Lateral patella displacement of 18.27±3.76 mm (range 15.85-20.64mm, interquartile range (IQR) of 4.79) was measured. The medial patella displacement showed 24.47±6.59mm (range 19.29-29.76mm, IQR of 10.47). The test-retest measurement error was 2.32±1.76mm (IQR of 2.38mm), with five outliers. There was greater test-retest variability between the measurements of the medial displacement comparing to the lateral one (4) Conclusions: The test-retest variability reached 7% of the patella displacement. Other parameters provided no significant correlations. Based on the natural patellofemoral mobility a precise and clinically relevant quantification of patella mobility is allowed.

The simplest elasticity model of foundation underlying a slender beam under flexure was conceived by Winkler, requiring local proportionality between soil reactions and beam deflection. Such an approach leads to well-posed elastostatic and elastodynamic problems, but, as highlighted by Wieghardt, it provides elastic responses which are not technically significant for a wide variety of engineering applications. Thus, Winkler's model was replaced by Wieghardt himself by assuming that the beam deflection is the convolution integral between soil reaction field and an averaging kernel. Due to conflict between constitutive and kinematic compatibility requirements, the corresponding elastic problem of an inflected beam resting on Wieghardt foundation results to be ill-posed. Modifications of the original Wieghardt model were proposed by introducing fictitious boundary concentrated forces of constitutive type, which are physically questionable, being significantly influenced on prescribed kinematic boundary conditions. Inherent difficulties and issues are overcome in the present research using a displacement-driven nonlocal integral strategy got by swapping input and output fields involved in Wieghardt's original formulation. That is, nonlocal soil reaction fields are output of integral convolutions of beam deflection fields with an averaging kernel. Equipping the displacement-driven nonlocal integral law with the bi-exponential averaging kernel, an equivalent nonlocal differential problem, supplemented with non-standard constitutive boundary conditions involving nonlocal soil reactions, is established. As a key implication, the integro-differential equations governing the elastostatic problem of an inflected elastic slender beam resting on displacement-driven nonlocal integral foundation are replaced with much simpler differential equations supplemented with kinematic, static and new constitutive boundary conditions. The proposed nonlocal approach is illustrated by examining and analytically solving exemplar problems of structural engineering. Benchmark solutions for numerical analyses are also detected.

In the paper, the author finds bounds of the sine and cosine along a circle on the complex plane in terms of two double inequalities for the norms of the sine and cosine along a circle on the complex plane.

In the paper, the author discusses and computes bounds of the sine and cosine along straight lines on the complex plane.

This article explores matter collineations (MCs) of static plane-symmetric spacetimes, considering the stress-energy tensor in its contravariant and mixed forms. We solve the MC equations in two cases: when the energy-momentum tensor is nondegenerate and degenerate. For the case of degenerate energy-momentum tensor, we employ a direct integration technique to solve the MC equations, which leads to an infinite-dimensional Lie algebra. On the other hand, when considering the nondegenerate energy-momentum tensor, the contravariant form results in a finite-dimensional Lie algebra with dimensions of either 4 or 10. However, in the case of the mixed form of the energy-momentum tensor, the dimension of the Lie algebra is infinite. Moreover, the obtained MCs are compared with those already found for covariant stress-energy.

In recent years, drones have been used in a wide range of fields such as agriculture, transportation of goods, and security. Drones equipped with communication facilities are expected to play an active role as base stations in areas where ground base stations are unavailable, such as disaster areas. In addition, asynchronous operation is being considered for local 5G in order to support all kinds of use cases. In asynchronous operation, cross-link interference between base stations is an issue. This paper attempts to reduce the interference caused by the drone network by introducing circularly polarized antennas. Numerical analyses are conducted to validate the effectiveness of the proposed system, where SIRs (Signal-to-Interference Ratio) are shown to be improved significantly as the numerical evaluation results.

Background and Objectives Depression in childhood often co-occurs with anxiety disorders and a range of somatic symptoms. Recent studies have identified physical activity as a target for preventing the onset of depression. Idiopathic ventricular extrasystoles (VE) in children are sometimes associated with somatic symptoms and limitations in physical activity. The problem of arrhythmia existence can also be distressing for children and their parents. The study was conducted to determine the relationship between symptoms of depression, physical activity and somatic symptoms in children with idiopathic VE. Materials and Methods The study of children with structurally normal hearts and VE was approved by the Ethics Committee No. 2021/10-1383˗859(1). The authors developed Questionnaire to assess symptoms, physical activity, and general well-being. Symptoms of depression evaluated with modified pediatric PHQ-9 (MP-PHQ-9) questionnaire with the interpretation of 0-4 scores for none; 5-9 mild; 10-14 moderate; >15 severe depression. Children aged ≥12 years and parents who assessed their children's condition completed Questionnaires. All children underwent 24-hour electrocardiography and echocardiography to evaluate arrhythmia frequency and cardiac condition. Results Questionnaires were completed by 60 children’s parents and 39 children (≥12 years old). Median children’s age was 13 (5-17) years. Palpitations experienced 26 (43.3%), chest pain 13 (21.7%), exercise intolerance 15 (25%) children. All patients had normal ventricular function and hemodynamically normal hearts. The median score of the MP-PHQ-9 completed by parents was 2 (0-16); by children - 4 (0-18). The median VE frequency was 4,77 (0,1-32,77) % per 24 hours. Extra-sports participation had 31 (51.7%) children with a median time of 3.75 (0.75-25) hours/ week. Eleven-patients were suspended from sports. There was no significant difference between VE frequency, and MP-PHQ-9 scores. Higher MP-PHQ-9 scores showed <5 hours/week active symptomatic children. Conclusions Idiopathic VE, limitations in physical activity and depression remain the actual theme for clinicians and need further research. Higher depression scores showed patients with somatic symptoms.

A 52-y/o asymptomatic male with history of hypertension, was referred to our Heart Failure Clinic due to report of hypertrophic cardiomyopathy, TTE with an increased end-diastolic thick-ness (basal inferoseptal of 23 mm, and basal anteroseptal of 21 mm). CMR demonstrated late gadolinium enhancement at the septum, anterior, inferolateral, and inferior walls with a mid-myocardial distribution, T1 mapping which reported an average T1 of 929 ms. A next-generation sequencing panel was requested. Results demonstrated hemizygosis, in the ga-lactosidase alpha gene, consistent with Fabry Disease. The replacement of the enzyme was start-ed. Extended familial genetic counseling and testing were done.

Background: Left ventricular noncompaction (LVNC) is a genetically determined cardiomyopathy, that occurs following a disruption of endomyocardial morphogenesis. The purpose of this study was to identify the clinical characteristics and genetic profile of children with LVNC. Methods: From February 2008 to July 2020, a total of 32 children (median 11.5 years) with LVNC were prospectively enrolled and followed up for the median of 4.02 years. Diagnosis was made based on characteristic features of LVNC in echocardiography and cardiovascular magnetic resonance (CMR). Patients’ clinical symptoms, family history, ECG, Holter ECG and genetic tests were also evaluated. Results: The most common presenting symptom was heart failure (31% of children). ECG abnormalities were noted in 56% of patients. The most prominent features were ventricular arrhythmias, sinus bradycardia and paroxysmal third-degree atrioventricular block. Most of the patients (94%) met the criteria for LVNC and CMR confirmed this diagnosis in 82% of cases. The molecular etiology was found in 53% of children. Conclusion: Although heart failure and arrhythmias were very frequent in our study group, thromboembolic events and genetic syndromes were rare. For accurate and reliable assessment of children with LVNC, it is necessary to get to know their family history and detailed clinical profile.

Safety assessment of structures can be obtained employing limit design to overcome uncertainties concerning actual response due to inelastic constitutive behavior and more generally to non-linear structural response and loads’ random variability. The limit analysis is used for evaluating the safety of the structures directly starting from load level without any knowledge of the load history. In the paper, the lower bound calculation is proposed where a new strain-based approach is used that allowed describing the residual stress and displacement in terms of permanent strain. The strategy used the permanent strain as the effective parameters of the procedure so that it was possible to assess the ductility requirements for the complete load program developed till collapse or shakedown. The procedure is compared to experimental results obtained on aluminum beams in shakedown.

In urban areas, deep excavation-induced ground deformation may damage adjacent existing structures and is conventionally evaluated by levelling at installed settlement points. However, a small number of measurements cannot represent the total change in ground deformation adjacent to excavation sites. Furthermore, significant local subsidence may occur in places where settlement points have not been installed and only noticed after an accident. For deep excavation sites located in urban areas, paved pedestrian sidewalks are often located adjacent to sites, and construction activity can cause these paving blocks to displace. This study introduces a method to detect paving block displacement adjacent to deep excavation sites using terrestrial photogrammetry. A digital camera creating point cloud data (PCD) and an acquisition method satisfying the frontal and side overlap requirements were demonstrated. To investigate the displacement detection and measurement capabilities by PCD analysis, an experimental program was conducted, including a PCD comparison containing the uplift, settlement, and horizontal paving block displacement and reference data. The cloud-to-cloud distance computation algorithm was adopted for PCD comparison. Paving block displacement was detected for displacements of 5, 7.5, and 10 mm in the uplift, settlement, and horizontal directions; however, the horizontal displacements were less clear. PCD analysis enabled satisfactory measurements between 0.024 and 0.881 mm for the vertical-displacement cases, but a significant error was observed for the horizontal-displacement cases owing to the cloud-comparison algorithm. The measurement blind spot of limited settlement points was overcome by the proposed method that detected and measured paving block displacement adjacent to excavation sites.

In Holter monitoring, the precise detection of standard heartbeats and Ventricular Premature Contractions (PVCs) is paramount for accurate cardiac rhythm assessment. This study introduces a novel application of the 1D U-Net neural network architecture aimed at enhancing PVC detection in Holter recordings. Training data comprised the Icentia11k, INCART DB, and our custom dataset. The model’s efficacy was subsequently validated against traditional Holter analysis methodologies across multiple databases, including AHA DB, MIT 11 DB, NST, and another custom dataset encompassing challenging real-world examples. The results underscored the 1D U-Net model’s prowess in QRS complex detection, achieving near-perfect balanced accuracy scores across all databases. PVC detection exhibited variability, with balanced accuracy scores ranging from 0.909 to 0.986. Despite some databases, like the AHA DB, showcasing lower sensitivity metrics, their robust balanced accuracy accentuates the model’s equitable performance in discerning both false positives and negatives. In conclusion, while the 1D U-Net architecture is a formidable tool for QRS detection, there’s a clear avenue for further refinement in its PVC detection capability, given the inherent complexities and noise challenges in real-world PVC occurrences.

Analytical mechanics is the most basic discipline. The basic principles of analytical mechanics should also be applicable to general deformed objects. However, the virtual displacement principle proposed by analytical mechanics is only applicable to particle systems and rigid body systems, but not to general deformed objects. In this paper, the generalized virtual displacement principle of general deformed objects (such as, elastic objects, plastic objects, elasto-platic objects and flexible objects etc ) is derived by the method of analytical mechanics, which is also applicable to particle systems and rigid body systems. First of all, according to the method of analytical mechanics, the external force, internal force, constraint reaction force and elastic recovery force of the deformed object system under the equilibrium state are analyzed, and the concepts of virtual displacement, ideal constraint and virtual work are introduced, and the generalized virtual displacement principle (also called generalized virtual work principle) of deformed objects is proposed; secondly, vector form, coordinate component form and generalized coordinate form of generalized virtual displacement principle of deformed object are given; thirdly, as the application of the principle, the virtual displacement principle of deformed objects in plane polar coordinate system, space cylindrical coordinate system and spherical coordinate system is given; finally, a brief conclusion is drawn. This work unifies the virtual displacement principle of elastic object, plastic, elastoplastic etc deformed object systems and rigid object systems with the basic method of analytical mechanics. It is a basic principle for dealing with the static problems of deformed objects. This work also lays a foundation for the further study of the dynamics of deformed object systems.

Directional dithering of a laser beam potentially limits the detection accuracy of a laser triangulation displacement probe. A theoretical analysis indicates that the measurement accuracy will linearly decrease as the laser dithering angle increases. To suppress laser dithering, a laser triangulation displacement probe with laser beam pointing control, which consists of a collimated red laser, a laser beam pointing control setup, a receiver lens, and a charge-coupled device, is proposed in this paper. The laser beam pointing control setup is inserted into the source laser beam and the measured object and can separate the source laser beam into two symmetrical laser beams. Hence, at the angle at which the source laser beam dithers, the positional averages of the two laser spots are equal and opposite. Moreover, a laser dithering compensation algorithm is used to maintain a stable average of the positions of the two spots on the imaging side. Experimental results indicate that with laser beam pointing control, the standard variance of the fitting error decreases from 0.3531 to 0.0100, the repeatability accuracy can be decreased from ±7mm to ±5 μm, and the nonlinear error can be reduced from ±6 %FS to ±0.16 %FS.

Efficient thermal management of modern electronics requires the use of thin films with highly anisotropic thermal conductivity. Such films enable the effective dissipation of excess heat along one direction while simultaneously providing thermal insulation along the perpendicular direction. In this study, we investigate the thermal conductivity of bilayer graphene (BLG) sheets using non-equilibrium molecular dynamics, examining both in-plane and cross-plane thermal conductivities. The in-plane thermal conductivity of 10 nm × 10 nm BLG with zigzag and armchair edges at room temperature is found to be around 204 W/m.K and 124 W/m.K, respectively. The in-plane thermal conductivity of BLG increases with sheet length. For all sizes, BLG with a zigzag edge exhibits higher thermal conductivity than that of the armchair edge, with this difference becoming more pronounced as the lengths of the sheets increase. In addition, increasing temperature from 300 K to 600 K decreases the in-plane thermal conductivity of a 10 nm× 10 nm zigzag BLG by about 34%. Similarly, the application of a 12.5% tensile strain induces a 51% reduction in its thermal conductivity compared to the strain-free values. Armchair configurations exhibit similar responses to variations in temperature and strain, but with less sensitivity. Furthermore, the cross-plane thermal conductivity of BLG at 300 K is estimated to be 0.05 W/m·K, significantly lower than the in-plane results by approximately four orders of magnitude. The cross-plane thermal conductance of BLG decreases with increasing temperatures, specifically, at 600 K, its value is almost 16% of that observed at 300 K.

The present paper deals with an improvement of the strengthening technique consisting in the combined use of straps—made of stainless steel ribbons—and CFRP strips, to increase the out-of-plane strength of masonry walls. The straps of both the previous and the new combined technique pass from one face to the opposite face of the masonry wall through some holes made along the thickness, giving rise to a three-dimensional net of loop-shaped straps, closed on themselves. The new technique replaces the stainless steel ribbons with steel wire ropes, which form closed loops around the masonry units and the CFRP strips as in the previous technique. A turnbuckle for each steel wire rope allows the closure of the loops and provides the desired pre-tension to the straps. The mechanical coupling—given by the frictional forces—between the straps and the CFRP strips placed on the two faces of the masonry wall gives rise to an I-beam behavior of the facing CFRP strips, which begin to resist the load as if they were the two flanges of the same I-beam. Even the previous combined technique exploits the ideal I-beam mechanism, but the greater stiffness of the steel wire ropes compared to the stiffness of the steel ribbons makes the constraint between the facing CFRP strips stiffer. This gives the reinforced structural element greater stiffness and delamination load. In particular, the experimental results show that the maximum load achievable with the second combined technique is much greater than the maximum load provided by the CFRP strips. Even the ultimate displacement turns out to be increased, allowing us to state that the second combined technique improves both strength and ductility. Since the CFRP strips of the combined technique run along the vertical direction of the wall, the ideal I-beam mechanism is particularly useful to counteract the hammering actions provided by the floors on the perimeter walls, during an earthquake. Lastly, after the building went out of service, the box-type behavior offered by the three-dimensional net of straps prevents the building from collapsing, acting as a device for safeguarding life.

Ultrasound (US) scans of the inferior vena cava (IVC) provide useful information on the volume status of a patient. However, their investigation is user-dependent and prone to measurement errors. An important technical problem is the objective difficulty in studying a very compliant blood vessel like IVC, which makes large respirophasic movements and shows a complicated three dimensional geometry. Using bi-dimensional (2D) B-mode views either in long or short axis has improved the characterization of IVC dynamics compared to a measurement along a single direction (M-mode). However, specific movements of the IVC can challenge also the information provided by these 2D sections. Thus, these two orthogonal views, provided by an US system in X-plane, are here integrated by an innovative method. It is tested on simulated videos of the IVC performing complicated movements, that are compensated by the new method, overcoming the biased measurements provided by 2D scans. The method is then applied on example experimental data.

Victor Vasarely’s (1906-1997) important legacy to the study of human perception is brought to the forefront and discussed. A large part of his impressive work conveys the appearance of striking three-dimensional shapes and structures in a large-scale pictorial plane. Current perception science explains such effects by invoking brain mechanisms for the processing of monocular (2D) depth cues. Here in this study, we illustrate and explain the local effects of 2D color and contrast cues on the perceptual organization in terms of figure-ground assignments, i.e. which local surfaces are likely to be seen as “nearer” or “bigger” in the image plane. Paired configurations are embedded in a larger, structurally ambivalent pictorial context inspired by some of Vasarely’s creations. The figure-ground effects these configurations produce reveal a significant correlation between perceptual solutions for “nearer” and “bigger” when no other monocular depth cues are given in the image. In consistency with previous findings on similar, albeit simpler visual displays, a specific color may compete with luminance contrast in resolving the planar ambiguity of a complex pattern context. Vasarely intuitively understood, and successfully exploited, this kind of subtle context effect in his art, well before empirical investigations had set out to study and explain their genesis in terms of information processing by the visual brain.

Introduction: Systemic lupus erythematosus (SLE) is an autoimmune disease associated with an increased risk of cardiovascular diseases (CVD), leading to elevated mortality rates among patients. We aimed to evaluate the levels of cardio-ankle vascular index (CAVI), global longitudinal strain (GLS), ventricular-arterial coupling (VAC) and high-sensitivity cardiac troponin (hsTn), in SLE patients and to explore their relationship with clinical parameters. Methods: This cross-sectional study enrolled 82 SLE patients without evident cardiac or kidney impairment and 41 age- and sex matched healthy controls. We comparatively evaluated CAVI, GLS, VAC, and hsTn between SLE patients and controls, and we assessed their association among SLE patients with disease activity based on the SELENA-SLEDAI Activity Index. Multivariate regression analysis was performed to identify independent predictors of CAVI and hsTn within the SLE cohort. Results: In comparison to healthy controls, SLE patients presented with significantly higher CAVI, GLS and hsTn levels, while VAC was significantly reduced (p&lt;0.001). Further, SLE patients with active disease (SELENA-SLEDAI≥4) exhibited higher levels of CAVI and troponin than those with inactive disease (p&lt;0.001). SLEDAI was an independent predictor of CAVI, while VAC and SLEDAI were independent determinants of hsTn in SLE cohort. Conclusion: SLE patients displayed abnormal levels of CAVI, VAC, GLS, and troponin compared to healthy individuals. Our findings implicate the potential of those CV novel CVD risk factors to refine screening and therapeutic strategies for this specific population.

In this paper, an ultracompact combined sensor for displacement and angle synchronous measurement is proposed based on self-imaging effect of optical microgratings. Using a two-grating structure, linear and angular displacement can be measured by detecting the change of phase and amplitude of the optical transmission respectively within one single structure in meantime. The optical transmitted properties of the two-grating structure are investigated in both theory and simulation. Simulated results indicate that, the optical transmission changes in a sinusoidal relationship to the input linear displacement. Meanwhile, the amplitude of the curve decreases with an input pitch angle, indicating the ability for synchronous measurement within one single compact structure. The synchronous measurement of the linear displacement and the angle is also demonstrated experimentally. The results show a resolution down to 4nm for linear displacement measurement, and a sensitivity of 0.26mV/arcsec within a range of ±1° for angle measurement. Benefitting from a simple common-path structure without using optical components including reflectors and polarizers, the sensor shows an ultrahigh compactness for multiple-degrees-of-freedom measuring, indicating the great potential for this sensor in the fields such as integrated mechanical positioning and semiconductor fabrication.

Left ventricular (LV) remodeling is a dynamic process which is characterized by abnormal LV wall thickness and altered myocardial geometry, and it is considered as a negative prognostic factor in both heart failure with reduced eject fraction (HFrEF) and heart failure with preserved eject fraction (HFpEF). Hypertension, type 2 diabetes (T2D) and obesity are strongly correlated with the development and the progression of LV remodeling, LV hypertrophy and LV systolic and/or diastolic dysfunction. Indeed, the beneficial impact of exercise training on primary and secondary prevention of cardiovascular disease (CVD) has been well-established. Recent studies highlight that exercise training enhances functional capacity, muscle strength and endurance, cardiac function and cardiac-related biomarkers, among patients with established coronary artery disease (CAD) or HF, thus improving substantially their cardiovascular prognosis, survival rates and needs for rehospitalization. Therefore, in this review article, we discuss the evidence of LV remodeling in patients with cardiometabolic risk factors, such as hypertension, T2D, obesity, and also highlight the current studies evaluating the effect of exercise training on LV remodeling in these patients.

Introduction: Intraventricular Hemorrhage (IVH) is a devastating condition mostly in preterm infants at < 30 weeks GA with large morbidities and mortality usually in the first 72 hours after birth. Prevention seems to be the only way to completely deal with this problem. The IVH prevention in this age group has been studied and includes some strategies such as prenatal corticosteroids, cesarean delivery, careful extraction among others, but still, it has an unacceptably high incidence in this population. A protocol with the name Drive to Zero IVH Prevention Project that was presented in one of EpicLatino conferences some years ago. As with any quality improvement in practices, we adapted this project to our unit. Objective: To compare the IVH incidence in our unit after the protocol implementation with and historic cohort from the same unit and with all other units un the epilactino network. Material and method: In October 2017 we begun to implement a neuro protection protocol. For this analysis we include every patient born <30 weeks of GA, inborn or outborn but less than 2 days old, that survived at least three days and had a neuroimaging preformed. We include cases until July 2022, and we use the EpicLatino, a Latin-American database, from 2018 to 2020 excluding our own unit for comparison as well as an historical cohort from our unit from 2010-2017. The protocol consists of: Minimal manipulation, low volume ventilation, one routine fiscal exam a day, neutral head position, one blood pressure measured per shift, no keel stick measurements, continuous dim light and low noise level, minimal touch, no vasoactive therapy except in extreme cases, temperature and humidity at 80%, catheters, when possible, fluid restriction followed with diuresis, no PDA therapy or Echo if possible and routine therapy with hydrocortisone, erythropoietin, caffeine, parenteral nutrition, and trophic feeding. e performed a univariate analysis for IVH and groups and a logistic regression model with variables that had statistical significance in the univariate analysis. Results: The study group included 64 cases, the historic cohort 123 and the EpicLatino 1029. Demographic characteristics were similar with few statistically significant differences. We found four grade 1-2 and six grade 3-4 IVH in the study group (some caused by very traumatic delivery with multiples hematomas in head, body, and extremities), all significantly lower that the other two groups. The logistic regression model confirmed the independent statistically significant result in the study group. Conclusion: The hemorrhage during delivery must be prevented by the obstetric team. Afterwards, a set of interventions like very gentle handling with minimal manipulation and unnecessary strict lab managing seams to decrease the incidence of IVH.

Optical tweezers, as a kind of ultra-sensitive acceleration sensing platform, show a minimum measurable value inversely proportional to the square of the diameter of the levitated spherical particle. However, the coupling of the displacement measurement between axes becomes notable, along with the increasing of the diameter. This paper analyzes the source of coupling in a forward scattering far-field detection regime and proposes a novel method of suppression. We theoretically and experimentally demonstrated that when three variable irises added into detection optics, without changing other parts of optical structures, the decoupling of triaxial displacement signals mixed with each other show significant improvement. The detection coupling ratio reduction of 49.1 dB and 22.9dB has been realized in radial and axial direction respectively, which is principally in accord with simulations. This low cost and robust approach makes it possible to accurately measure three-dimensional mechanical quantities simultaneously and even go further such as active cooling the particle to quantum ground state.

Arrhythmogenic right ventricular cardiomyopathy (ARVC) is a rare inherited disorder which is characterized by fibrofatty degeneration of cardiac muscles mainly in the right ventricular myocardium. It may cause tachyarrhythmias or right-heart failure or may cause sudden death, especially in young athletes. In our case report, we present a case of young age male patient who presented at a local community hospital with the complaint of atypical chest pain, palpitations, and vomiting and sustained ventricular tachycardia (VT) on electrocardiograph (ECG) showing sustained ventricular tachycardia, left bundle branch morphology with the superior axis. The normal sinus rhythm was achieved after multiple DC cardioversion attempts and he was referred to our tertiary care hospital. Later ECG demonstrated epsilon waves and T wave inversion in v1 to v4 and RBBB morphology. The echocardiography showed a severely dilated right ventricle with dysfunction and right ventricle ventricular apical aneurysm. The definitive diagnosis of ARVC was made as per Revised Task Force Criteria 2010 and the electrophysiology review suggested implantable cardiac defibrillator (ICD) device placement. The patient successfully received a dual-chamber ICD device and he remained asymptomatic.

The lay-up of cross laminated timber (CLT) leads to significant differences in properties over its cross-section. Particularly the out-of-plane shear behavior of CLT is effected by the changes in shear moduli over the cross-section. Results from laboratory shear tests are used to evaluate the shear stiffness of 3- and 5-layer CLT panels in their major and minor strength direction. The results are compared to calculated shear stiffness values on evaluated single-layer properties as well as commonly used property ratios using the Timoshenko beam theory and the shear analogy method. Differences between the two calculation approaches are pointed out. The shear stiffness is highly sensitive to the ratio of the shear modulus parallel to the grain to the shear modulus perpendicular to the grain. The stiffness values determined from two test measurements are compared with the calculated results. The level of agreement is dependent on the number of layers in CLT and the property axis of the CLT panels.

Pyrochlore oxides (A2B2O7) are potential nuclear waste substrate material due to their superior radiation resistance properties. We performed molecular dynamics simulations to study the structural properties and displacement cascades in ytterbium titanate pyrochlore (Yb2Ti2O7). We computed threshold displacement energy ( Ed ) and lattice constant ( ao) of Yb2Ti2O7. The effect of displacement cascades in Yb2Ti2O7 of recoils of energies 1 keV, 2 keV, 5 keV, 10 keV in different crystallographic directions ([100], [110], [111]) were studied. The number of defects is found to be proportional to the energy of incident PKA. Additionally, the Ed of pyrochlore is computed and it exhibits anisotropy. Furthermore, radiation damage in high-entropy pyrochlore (HEPy) i.e., YbYTiZrO7, YbGdTiZrO7 , Yb0.5Y0.5Eu0.5Gd0.5TiZrO7 were investigated and compared with Yb2Ti2O7. It was found that HEPy have a larger Ed as compared with Yb2Ti2O7 which exhibits characteristic of lower radiation damage resistance than HEPy. Our simulation proposed that HEPy alloys are more radiation resistant than individual pyrochlore constituents . This work will provide atomic insights in developing substrate materials for nuclear waste applications.

Risk stratification for malignant ventricular arrhythmias and sudden cardiac death is a daunting task for physicians in daily practice. Multiparametric mapping sequences obtained via cardio-vascular magnetic resonance imaging can improve the risk for malignant ventricular arrhythmias by unveiling the presence of pathophysiological pro-arrhythmogenic processes. However, their employment in clinical practice is still restricted. The present review explores the current evidence supporting the association between mapping abnormalities and the risk of ventricular arrhyth-mias in several cardiovascular diseases. The key message is that further clinical studies are needed to test the additional value of mapping techniques beyond conventional cardiovascular magnetic resonance imaging for selecting patients eligible for an implantable cardioverter defibrillator.

Introduction: Catecholaminergic polymorphic ventricular tachycardia (CPVT) is a rare cardiac ion channelopathy. This study examined the clinical characteristics, genetic basis, and arrhythmic outcomes of CPVT patients from China. Methods: PubMed and EMBASE were systematically searched for case reports or series reporting on CPVT patients from China until February 19th, 2022 using the keyword “Catecholaminergic Polymorphic Ventricular Tachycardia” OR “CPVT”, with the location limited to “China” OR “Hong Kong” or “Macau” in EMBASE, with no language or publication type restriction. Clinical characteristics, genetic findings, and primary outcome of spontaneous ventricular tachycardia/ventricular fibrillation (VT/VF) were analyzed. Results: A systematic search of the PubMed and Embase databases yielded 1049 and 47 articles, respectively. After the exclusion of overlapping cohorts, a total of 58 unique cases from 15 studies (median presentation age: 8 [5.0-11.8] years old) were included. All patients except for one presented at or before 19 years of age. 56 patients (96.6%) were initially symptomatic. Premature ventricular complexes (PVCs) were present in 44 of 51 patients (86.3%) and VT in 52 of 58 patients (89.7%). Genetic tests were performed on 54 patients (93.1%) with a yield of 87%. RyR2, CASQ2, TERCL, and SCN10A mutations were found in 35 (71.4%), 12 (24.5%), one (0.02%) patient, and one patient (0.02%) respectively. 54 patients were treated with beta-blockers, eight received flecainide, five received amiodarone, two received verapamil and one received propafenone. Sympathectomy (n=10) and implantable-cardioverter defibrillator implantation (n=8) were performed. On follow-up, 13 patients developed VT/VF. Conclusion: This is the first systematic review of CPVT patients from China. Most patients had symptoms on initial presentation, with syncope as the presenting complaint. RyR2 mutation accounts for more than half of the CPVT cases, followed by CASQ2, TERCL and SCN10A mutations.

Background: Left ventricular noncompaction (LVNC) is a genetically and phenotypically heterogeneous cardiomyopathy characterized by a two-layered myocardium consisting of compacted and noncompacted segments, prominent ventricular trabeculations, and intertrabecular recesses. Patients with LVNC are at increased risk to develop heart failure, atrial and ventricular arrhythmias, and/or systemic thromboembolic events. Familial forms of primary sinus bradycardia have been attributed to mutations in HCN4. There are very few reports about the association between HCN4 mutations and LVNC. The aim of our study was to characterize the clinical phenotype of families with LVNC and sinus bradycardia caused by mutation of the HCN4 gene. Methods: From March 2008 to July 2021 we prospectively enrolled 6 patients from 4 families with diagnosed isolated LVNC based on the clinical presentation, family history and echocardiographic and cardiovascular magnetic resonance (CMR) evidence of LVNC. Next generation sequencing (NGS) analysis was undertaken for evaluation of the molecular basis of the disease in each family. Results: A total of 6 children (median age 11 years) were enrolled and followed prospectively for the median of 12 years. All 6 patients were diagnosed with LVNC by echocardiography and 5 participants additionally by CMR. The presence of LGE was found in 3 children. Sinus bradycardia and dilation of the ascending aorta occurred in 5 studied patients. In 4 patients from 3 families the molecular studies demonstrated the presence of rare heterozygous HCN4 mutations. Conclusion: (1) The HCN4 mutation influences the presence of a complex LVNC phenotype, sinus bradycardia and dilation of the ascending aorta. (2) HCN4 mutation may be associated with the early presentation of clinical symptoms and the severe course of the disease. (3) It is particularly important to assess myocardial fibrosis not only within the ventricles, but also in the atria in patients with LVNC and sinus bradycardia.

Introduction: Catecholaminergic polymorphic ventricular tachycardia (CPVT) is a rare cardiac ion channelopathy. The aim of this study is to examine the genetic basis and identify predictive factors for arrhythmic outcomes of CPVT patients from China. Methods: PubMed and MedRxiv were systematically searched for case reports or case series reporting on CPVT patients from China. Clinical characteristics, genetic findings and primary outcome of spontaneous ventricular tachycardia/ventricular fibrillation (VT/VF) were analyzed. Results: A total of 56 (median presentation age=9 [6-13] years old) patients were included. All patients except for one presented at or before 19 years of age. Fifty-three patients (94.6%) were initially symptomatic. PVCs were present in 40 out of 45 patients (88.9%) and VT in 51 out of 56 patients (91.1%). Genetic tests were performed in 50 patients (89.3%). RyR2, CASQ2 and TERCL mutations were found in 32 (57.1%), 11 (19.6%) and one (0.02%) patients, respectively. Fifty patients were treated with beta-blockers, eight patients received flecainide, four patients received amiodarone, two received verapamil and one received propafenone. Sympathectomy (n=10) and implantable-cardioverter defibrillator implantation (n=7) were performed. On follow-up, 17 patients developed incident VT/VF. Conclusion: This is the first systemic review and meta-analysis of CPVT patients from China. Most patients had symptoms on initial presentation, and around a third had VT as the presenting complaint. RyR2 mutation accounts for more than half of the CPVT cases, followed by CASQ2 and TERCL mutations. Some of these mutations have not been hitherto reported outside of China. Most patients received β-blocker therapy. Around 18% had sympathectomy and 13% had ICDs implanted.

The outflow tract of crocodilians resembles that of birds and mammals as ventricular septation is complete. The arterial anatomy however, presents with a pulmonary trunk originating from the right ventricular cavum, and two aortae originating from either the right or left ventricular cavum. Mixing of blood in crocodilians cannot occur at ventricular level as in other reptiles, but instead takes place at aortic root level by a shunt, the Foramen of Panizza, the opening of which is guarded by two facing semilunar leaflets of both bicuspid aortic valves. Methods. Developmental stages of Alligator mississipiensis, Crocodilus niloticus and Caiman latirostris, have been studied. Results and Conclusions. The outflow tract septation complex can be divided into 2 components. The aorto-pulmonary septum divides the pulmonary trunk from both aortae, whereas the interaortic septum divides the systemic from the visceral aorta. Neural crest cells are most likely involved in the formation of both components. Remodeling of the endocardial cushions and both septa results in the formation of bicuspid valves in all three arterial trunks. The foramen of Panizza originates intracardially as a channel in the septal endocardial cushion.

The effects of photon inertia on the determination of its trajectory were verified and the representation of a displacement mass characterized by the flow of the number of wavefronts and the decomposition of photon inertia into parts associated with translation and rotation motions was considered. It was found that with the relativistic increase of the photon's resistance to change its directional properties, it inhibits the relativistic trajectory of the second torque, of Minkowski, in an angular range of incidence. After synchronizations, in the OAM inversions, there are reductions of the inertia associated to the translational part that assumes classical predominance, where the relativistic trajectory is allowed while the photon offers less resistance to changes in its directional properties. The classical-relativistic variability of the photon inertia characterizes the classical or relativistic profile of the energy distribution in forms of motion, where adjustments of the rotational and translational parts can be performed as a function of the refractive index rate, temperature and angle of incidence. It was found that with increasing temperature of the refringent medium, the synchronizations displacement in the sense of the normal incidence. A specific vacuum temperature for the refringent medium was characterized, where the photon exhibits a classical-relativistic synchronization under all angles of incidence, characteristic of its immaterial state in vacuum.

Natural gas hydrate has gained significant attention in recent years. To safely and sustainably exploit the natural gas from gas hydrate-bearing sediments, it is crucial to understand the long-term mechanical characteristics of the hydrate reservoir. In this study, the influence of hydrate and fine particles on the strain rate dependence of hydrate-bearing sediments under plane strain conditions has been studied. The experimental results show that the strain rate dependency of the mechanical properties of hydrate-bearing sediments is positively correlated with hydrate saturation instead of the morphology of hydrate in sediments. The residual strength of hydrate-bearing sediments is primarily controlled by the hydrate saturation and is independent of the strain rate. Changes in hydrate saturation, and fines content, can affect the relationship between the strain rate and shear band angle. Finally, the local volumetric expansion effect of hydrate-bearing sediments without fines content is more significant and shows a strong strain rate dependence characteristic. Overall, this study provides valuable insights into the long-term mechanical characteristics of hydrate reservoirs. These insights can contribute to the development of a constitutive model of hydrate-bearing sediments with time-dependence in the future, and which is meaningful to the exploitation of natural gas hydrate.

The purpose of this study is to improve the performance of walls under out-of-plane loads, particularly when subjected to the hammering action of the floors. The idea behind the paper is to provide the masonry walls with a device that behaves like a buttress, without having to build a traditional buttress. The solution presented here consists of a mechanical coupling between the three-dimensional net of steel ribbons of the CAM system and the CFRP strips. Since the steel ribbons of the CAM system have a pre-tension, the mechanical coupling allows the steel ribbons to establish a semi-rigid transverse link between the CFRP strips bonded on two opposite sides of a wall. Therefore, two vertical CFRP strips tied by the steel ribbons behave like the flanges of an I-beam and the flexural strength of the ideal I-beam counteracts the out-of-plane displacements of the wall. The experimental results showed that the combined technique inherits the strong points of both constituent techniques: the delamination load is comparable to that of the specimens reinforced with the CFRP strips and the overall behavior is ductile as for the specimens reinforced with the CAM system. They also allowed us to design a more performing combined technique.

Assessment of cardiac function is the leading parameter when evaluating the state of the cardiovascular system of patients undergoing chronic hemodialysis. The aim of the paper: to assess the state of the cardiovascular system of these patients using new sensitive echocardiography and Doppler techniques and thus advance the prevention of cardiovascular disease.Method: Twenty children with end-stage renal insufficiency on chronic hemodialysis and twenty healthy controls underwent echocardiographic monitoring using standard Doppler and tissue Doppler imaging. Structural and functional changes in the left ventricle were evaluated.Results: Patients on hemodialysis had significantly greater left ventricular mass indices compared to the controls (p<0.001). The patients on hemodialysis had preserved systolic function – their fractional shortening, ejection fraction and Sm (systolic myocardial velocity) did not differ significantly compared to the controls (p>0.05). Early diastolic function in children on hemodialysis was also preserved: the E/A and Em/Am ratio did not differ significantly from the control group (p>0.05). Children on hemodialysis exhibited impaired late diastolic function (compliance index), that is, considerably higher E/Em compared to controls (p<0.00). Myocardial Performance Index values showed statistically significant elevation in children on hemodialysis compared to the control group (p<0.001).Conclusion: Tissue Doppler in tandem with conventional Pulsed Doppler can provide additional information on left ventricular filling pressures (E/Em) in children on hemodialysis. It is therefore recommended to perform routine measuring of Em waves and the E/Em ratio, not only in order to evaluate myocardial relaxation and ventricular filling pressures, but primarily to stratify risk and provide a prognosis.

This paper reports the novel design of a touch mode capacitive pressure sensor (TMCPS) system with a wireless approach for a full-range continuous monitoring of ventricular pressure. The system consists of two modules: an implantable set and an external reading device. The implantable set, restricted to a 2x2 cm² area, consists of a TMCPS array connected with a dual-layer coil, for making a reliable resonant circuit for communication with the external device. The capacitive array is modelled considering the small deflection regime for achieving a dynamic and full 5-300 mmHg pressure range. In this design, the two inductive-coupled modules are calculated considering proper electromagnetic alignment, based on two planar coils and considering the following: 13.56 MHz frequency to avoid tissue damage and three types of biological tissue as core (skin, fat and muscle). The system was validated with the Comsol Multiphysics and CoventorWare softwares; showing a 90% power transmission efficiency at a 3.5 cm distance between coils. The implantable module includes aluminum- and polyimide-based devices, which allows ergonomic, robust, reproducible, and technologically feasible integrated sensors. In addition, the module shows a simplified and low cost design approach based on PolyMEMS INAOE® technology, featured by low-temperature processing.

This research study examined the compensation requirements for households facing involuntary displacement caused by a railway development project in Ethiopia's Amhara Region. Using the contingent valuation approach, researchers estimated compensation needs, taking into account ecosystem services and household characteristics. Surveys and questionnaires were conducted with 170 affected households to gather data on compensation preferences and experiences using double-bounded dichotomous method. The collected data were analyzed using a probit model to assess the influence of compensation amount, satisfaction, marital status, religion, and education on the satisfaction levels of affected households. The findings emphasized the significant impact of these factors and the necessity of fair compensation policies in development projects. The study revealed that the Minimum Willingness to Accept (MWTA) for households was - 2.274 billion Ethiopian Birr, significantly surpassing the compensation amount provided. The study highlighted the importance of considering household possessions and the ecosystem in designing tailored compensation strategies. The research revealed strong opposition to displacement, underscoring the need for customized compensation schemes that address preferences and non-monetary aspects. The discontent expressed by the respondents emphasized the importance of designing compensation schemes that ensure the sustenance of livelihoods without further disruptions. The study provided valuable guidance to stakeholders involved in addressing involuntary displacement, empowering them to make informed decisions and implement context-specific compensation policies. These findings contribute to the formulation of more effective and equitable compensation schemes, emphasizing comprehensive strategies for the welfare of affected households.

Monitoring and maintenance of cracked structures are generally done using structural integrity assessments. The plastic zone (PZ) crack path (CP) criteria state that a crack grows in the direction when the radius of the plastic zone ahead of the crack tip reaches a minimum value. The PZ can be evaluated using Stress intensity factors (SIF). The SIFs under mixed-mode loading were extracted from literature from three samples: two SENT samples made from polycarbonate and one modified C(T) sample made from low-carbon steel. In addition, the CP angle was evaluated for the W and R-criteria. It was found that both can predict the CP for lateral cracks in both tested materials and monotonic and cyclic load when the mode-mixity does not change considerably from one crack length to the next one or goes beyond 0.2. Moreover, the R-criterion exhibited an error as high as 1.7%, whereas the W-criterion showed a 6% error on the last crack length for the low carbon steel sample under cyclic load, which had a 100% increase in mode-mixity. Finally, the applicability of LEFM is checked, while the CP is sought by finding the size of the PZ.

Worldwide, millions of kilometres of sewers are constructed from concrete pipes. Unfortunately, concrete sewers are susceptible to corrosion from biogenic hydrogen sulphide, and though they may pass visual inspection, their ability to hold together under load may be degraded. This paper presents the design of a teleoperated robot with a protractible probe, that allows an operator to apply a localised load to selected points within a concrete sewer pipe. We report findings from laboratory and field trials of our prototype, with initial results suggesting that this approach has the potential to contribute useful information to sewer maintenance planning.

The electronic structural evolution of LLM-105 crystal and the (101) plane of LLM-105 crystal under different pressures is investigated by the density functional theory (DFT) calculations and the surface properties of seven low-Miller-index planes of LLM-105 crystal were investigated in this study. The result demonstrates that the surface energy of (101) plane of LLM-105 is much smaller when compared with other low-Miller-index planes of LLM-105.In order to further investigate the stability of crystal structure and (101) plane of LLM-105 under different pressures, a series of pressures ranged from 0 GPa to 55 GPa were applied during the DFT calculation, and the result shows that the electronic structures of LLM-105 crystal and the (101) plane changed with the increase of external pressure and the evolution process of (101) plane is different from that of LLM-105 crystal structure.

There are no investigations about the outcomes of idiopathic PVCs catheter ablation (CA) in athletes compared to sedentary population. We conducted a prospective single-centre observational study. The primary and secondary procedural outcomes were premature ventricular contractions (PVCs) post-ablation reduction in athletes vs. non-athletes group and in agonist vs. leisure-time athletes. The third was the evaluation of the resumption of physical activity and the improvement of symptoms in agonist and leisure-time athletes. From January 2020 to October 2022 we enrolled 79 patients with RVOT/LVOT/fascicular PVC presumed origin. The median percentage of decrease between the pre-procedure and post-procedure Holter monitoring in non-athletes group was 96 (IQR 68 – 98) and 98 in athletes group (IQR 92 – 99) (p=0,08). Considering the athletes, the median percentage of decrease in PVCs number was 98 (IQR 93-99) and 98 (IQR 87-99) respectively in leisure-time and agonistic athletes (p=0,42). Sixteen (70%) leisure time and 17 (90%) agonist athletes (p=0,24) have resumed physical activity 3 months after PVCs CA; among agonistic athletes, 59% have resumed competitive physical activity. Much of leisure-time (88%) and agonist (70%) athletes experienced an improvement in symptoms after ablation. PVC CA was effective and safe in both groups, reducing symptoms and allowing a quick and safe return to sports activities in athletes.

Background: Anthracyclines form the backbone of many systemic chemotherapy regimens but dose-limiting cardiotoxicity can also lead to reduction in cardiac function and an increased risk of heart failure. Methods: This review was conducted in accordance with PRISMA guidelines and registered on PROSPERO (CRD42022373496). Results: 26 studies met the eligibility criteria including a total of 910 patients. Overall reduction in pooled mean left ventricular ejection fraction (LVEF) post‐anthracyclines in the placebo arms of included randomised-controlled trials was 4.6% (95% CI, 2.7 to 6.6). The trend in LVEF showed a progressive decline until approximately 180 days after which there was no significant change. Those receiving a cumulative anthracycline dose 300 mg/m2 experienced a more profound reduction. The risk of a 10% absolute decline in LVEF from baseline or decline to an LVEF below 50%, the overall pooled risk was 16% (95% CI: 11 to 21; I2 = 77%). Sensitivity analyses by baseline LVEF and trastuzumab treatment status did not yield significant differences. Conclusion: While the mean LVEF decline in patients without cardioprotective therapy was clinically small, a vulnerable subset experienced significant impairment. Further research to best identify those who benefit most from cardioprotective therapies when receiving anthracyclines are required.

The Hertzian contact theory, as well as most of the other classical theories of normal and tangential contact, provides displacements and the distribution of normal and tangential stress components directly in the contact surface. However, other components of the full stress tensor in the material may essentially influence the material behaviour in contact. Of particular interest are principal stresses and the equivalent von Mises stress, as well as the gradient of the hydrostatic pressure. For many engineering and biomechanical problems, it would be important to find these stress characteristics at least in the contact plane. In the present paper, we show that the complete stress state in the contact plane can be easily found for axially symmetric contacts under very general assumptions. We provide simple explicit equations for all stress components and the normal component of the gradient of hydrostatic pressure in the form of one-dimensional integrals.

Abstract: As more and more numerical and analytical solutions to the linear neutron transport equation become available, verification of numerical results is increasingly important. This presentation concerns the development of another benchmark for the linear neutron transport equation. There are numerous ways of solving the transport equation, such as the Wiener-Hopf method based on analyticity, method of singular eigenfunctions, Laplace and Fourier transforms and analytical discrete ordinates, which is arguably one of the most straightforward, to name a few. Another potential method is the PN method, where the solution is expanded in terms of full range orthogonal Legendre polynomials and with orthogonality and truncation, the moments form a set of second order ODEs. Because of the half-range boundary conditions for incoming particles however, full range Legendre expansions are inaccurate near material discontinuities. For this reason, a double PN (DPN) expansion is more appropriate, where the incoming and exit-ing flux distributions are expanded separately to preserve the discontinuity at material interfaces. Here, a new method of solution for the DPN equations is proposed and demonstrated for an iso-tropically scattering medium.

Introduction Cone Beam Computed Tomography (CBCT) scans should be digitally oriented using a reference plane before being evaluated for patient growth and treatment outcome. Current orientation planes are usually dependent on the Porion points. Using more reliable landmarks than the Porion, we introduce the Acta plane and investigate its reliability as an alternative reference plane for cases in which the Porion point is inaccessible. Methods To test its reliability, a dental student and an orthodontist located sixteen skeletal and dental landmarks in sixteen CBCT scans, before and after reorientation. Also, four measurements were calculated based on these landmarks’ coordinates. The reorientation of these CBCT scans with the Acta plane was done by another dental student. Intraclass Correlation Coefficient (ICC) was calculated before and after orientation, intra- and inter-examiner. The data were tested for significance through the Shapiro Wilk test with a threshold set at 0.05. Through the ICC variation of the points’ coordinates, this article also evaluated the reliability of this plane with the t-paired and exact-sign tests. Results: The identification of landmarks was more reliable in the reoriented CBCT images than in the original images, with a significant increase of 0.012 in the median of the ICC. Linear and angular measures showed no significant differences between groups. Conclusion This plane is a reliable alternative for the orientation of CBCT images. The design of the Acta plane might allow the use of a smaller field of view and, consequently, a reduction in the radiation dose.

Real-time multi-axis distributed tactile sensing is a critical capability if robots are to perform stable gripping and dexterous manipulation, as it provides crucial information about the sensor-object interface. In this paper, we present an optical-based 6-axis tactile sensor designed in a fingertip shape for robotic dexterous manipulation. The distributed sensor can precisely estimate local XYZ force and displacement at ten distinct locations, and provide global XYZ force and torque measurements. Its compact size, comparable to that of a human thumb, and minimal thickness allow seamless integration onto existing robotic fingers, eliminating the need for complex modifications to the gripper. The proposed sensor design uses a simple, low-cost fabrication method. Moreover, the optical transduction approach uses light angle and intensity sensing to infer force and displacement from deformations of individual sensing units that form the overall sensor, providing distributed 6-axis sensing. The local force precision at each sensing unit in the X, Y, and Z axes is 20.89 mN, 19.19 mN, and 43.22 mN, respectively, over an local force range of approximately ±1.5 N in X and Y and 0 to -2 N in Z. The local displacement precision in the X, Y and Z axes is 56.70 μm, 50.18 μm and 13.83 μm, respectively, over a local displacement range of ±2 mm in the XY directions and 0 to -1.5mm in Z (i.e., compression). Additionally, the sensor can measure global torques, Tx, Ty and Tz, with a precision of of 1.90 N-mm, 1.54 N-mm and 1.26 N-mm, respectively. The fabricated design is showcased by integrating it with an OnRobot RG2 gripper and illustrating real-time measurements during in simple demonstration task which generate changing global forces and torques.

This report elucidates the first surgical correction of an infundibular muscular ventricular septal defect (VSD) in a one-year-old Ragdoll cat via cardiac arrest using cardiopulmonary bypass, a method that is rarely used in feline cardiac surgery. VSDs can lead to congestive heart failure and pulmonary hypertension, particularly in patients with large shunts. This case involved a VSD that was atypically located and classified under the Soto classification instead of the standard Kirklin classification. Detailed echocardiography revealed that the defect required intervention owing to left heart and main pulmonary artery enlargement. Despite the VSD being located on the contralateral side, as anticipated in the preoperative examinations, the choice of median sternotomy allowed for successful closure of the defect. Conversely, the insertion of two cannulas into the ascending aorta resulted in damage to the adjacent thoracic duct, causing transient chylothorax, which resolved with conservative treatment. Cardiac arrest induced by a cardioplegic solution facilitated the surgical procedure, although it has led to anemia in cats. However, on postoperative day 490, the patient exhibited only minor residual shunting with normalized heart size, and remained healthy. This technique appears to be a viable treatment option for congenital heart disease in cats.

This article explores the intricate journey of neural progenitor cells from the ventricular zones of the embryonic brain, focusing on their pivotal role in the formation of rich club networks, which are integral to the brain's functional architecture. Initially, the ventricular zones, particularly the cerebral ventricular zone, serve as the primary sites for the proliferation and differentiation of neural progenitors, giving rise to various types of neurons and glial cells. We delve into the sequential migration patterns of these cells, emphasizing how early-migrating neurons, destined to form deeper cortical layers, establish extensive and robust connections, potentially evolving into rich club nodes. These nodes are characterized by their high-degree connectivity and serve as crucial hubs for integrating and disseminating information across disparate brain regions.The article further discusses the implications of this developmental pathway in the context of brain network efficiency, resilience, and cognitive function. We highlight how disruptions in early cell migration can lead to anomalies in rich club formation, drawing connections to various neurodevelopmental disorders such as autism, ADHD and schizophrenia. Additionally, the significance of rich club nodes in maintaining efficient information transfer and network resilience is elucidated, underscoring their role in supporting complex cognitive processes and overall brain dynamics.In summary, this article offers a comprehensive overview of the developmental trajectory from the ventricular zones to the establishment of rich club networks, providing insights into the fundamental processes that shape the brain's intricate connectivity and functional capabilities. Ric

Introduction In sacubitril-valsartan (sacub/v), the effects of an angiotensin II receptor blocker (ARB) exerted by valsartan are strengthened by the addition of sacubitril, an inhibitor of neutral endopeptidases. PARADIGM - HF study proved this association to be superior to enalapril in reducing both all-cause death and cardiovascular mortality, as well as heart failure (HF) hospitalizations in patients with cardiac insufficiency and reduced left ventricular ejection fraction( HFREF) belonging to NYHA class II-IV. To test whether even in our experience sacub/v is associated with favorable outcomes concerning mortality and morbidity, an outpatient small population of HFREF patients was retrospectively studied, of whom one third was treated with sacub/v instead of conventional therapy with ACE -inhibitors or ARBs. Methods A retrospective cohort study was carried out to assess the effects of sacub/v in addition to beta-blocker and mineral receptor antagonist (MRA) in a group of HFREF patients in NYHA classes II-III compared with conventional therapy (comprising ACE inhibitor or ARB added to beta-blocker plus a MRA) administered in a second group of HFREF patients with comparable clinical features retrospectively enrolled as controls. In the two groups, the therapeutic regimen was established in accordance with the preferences of the treating physician. Additionally, in both groups, evidence-based drug therapy was supplemented by the adjunct of a loop diuretic, usually furosemide, at variable doses. The primary outcomes of interest were all-cause death and HF hospitalizations. Safety outcomes were symptomatic hypotension, angioedema, hyperkalemia and worsening renal function. Results Mortality at six months was 6.8% in patients under therapy with sacub/v versus 34% in those treated with conventional therapy (odds ratio[OR] = 0.14; 95% CI: 0.04-0.49). Moreover, HF hospitalizations in the observation period considered were 4.5% in sacub/v group versus 59% in the conventional therapy group (OR = 0.03; 95% CI: 0.01–0.14). Safety outcomes included in our study (angioedema, hyperkalemia, hypotension and worsening renal function) showed a comparable profile in the two groups, with evidence of good tolerability of sacub/v , except for the side - effect " hypotension" (PAS < 100 mm Hg) , found in 15.9% of patients under sacub/v versus 5.7% reported in controls (OR = 3.14; 95% CI: 0.94–10.55). Conclusions In our experience, sacub/v has yielded a strong protection against both all-cause death and HF hospitalizations at six months , in the absence of significant noxious side effects. Nevertheless, considering the retrospective character of the study and the relatively exiguous sample size, further post marketing observational studies would be desirable . In particular, studies aiming at exploring safety of the new pharmacologic principle, namely mainly focusing on hypotension and angioedema, are warranted, in order to validate further this very efficacious molecule for therapy of chronic HF, especially stable HFREF in NYHA classes II-III.

The internet of things and growing demand for smaller and advanced devices has created the problem of high heat production in the electronic equipment which greatly reduces the work performance and life of the electronic instruments. Thermal interface materials (TIMs) are placed in between heat generating micro-chip and the heat dissipater to conduct all the produced heat to the heat sink. Development of suitable TIMs with excellent thermal conductivity (TC) in both in-plane and through-plane directions is a very important need at present. For efficient thermal management, polymer composites are potential candidates. But in general their thermal conductivity is low compared to that of metals. The filler integration into the polymer matrix is one of the two approaches used to increase the thermal conductivity of polymer composites and is also easy to scale up for industrial production. Another way to achieve this is to change the structure of polymer chains, which fall out of the scope of this work. In this review, considering the first approach, the authors have summarized recent development in many types of fillers with different scenarios by providing multiple cases with successful strategies to improve through-plane thermal conductivity (TPTC) (K⊥). For better understanding of TC the comprehensive background is also presented. In the end, it is given a detailed conclusion which provides drawbacks of some filler, multiple significant routes recommended by other researchers to build Thermally Conductive Polymer Composites, future aspects along with direction so that the researchers can get a guideline to design an effective polymer based Thermal interface materials. A number of methods to improve the effective (out-plane) thermal conductivity of polymer composites are also discussed.

This paper investigates the classical but yet intriguing question of modeling orthotropic RC floor systems endowed with lightening elements, by means of a uniform orthotropic slab, in order to describe accurately the building response under seismic loads. The simplified method, commonly adopted by engineers, based on the equivalence between the transverse stiffness of the RC elements of the real floor and those of the orthotropic slab is presented. A case study in which this simplified method is used is also provided. Then, an advanced finite elements (FE) based method to determine the elastic properties of the equivalent homogenized orthotropic slab is proposed. Based on the results obtained from the application of this method to a case study, a discussion on the adequacy of the simplified method is also provided.

Obesity is a major risk factor for the development of life-threatening malignant ventricular tachyarrhythmias (VT) and sudden cardiac death (SCD). Risks may be highest for patients with high levels of the proinflammatory cytokine interleukin (IL)-6. We used our guinea pig model of high-fat diet (HFD) induced Ventricular arrhythmias, that exhibit heightened proinflammatory-like pathology which is also observed in human obesity VT, as well as immunofluorescence, and confocal microscopy approaches to evaluate the pathological IL-6 trans-signaling function and explore the underlying mechanisms. Using blind-stick and electrocardiogram (ECG) techniques, we tested the hypothesis that heightened IL-6 trans-signaling exhibit enhanced Ventricular arrhythmias /SCD incidence and underlying arrhythmia substrates. Remarkably, compared to low-fat (LFD) diet fed controls, HFD promotes phosphorylation of the IL-6 signal transducer and activator of transcription 4 (STAT4) leading to its activation and enhanced nuclear translocation of pSTAT4/STAT4 more than LFD controls and pSTAT3/STAT3 nuclear expression. Overactivation of IL-6 trans-signaling in guinea pigs prolonged the QT interval that resulted in greater susceptibility to VT/SCD with isoproterenol challenge, as also observed with the downstream Janus kinase (JAK) 2 activator. These findings may have potentially profound implications for more effective VT therapy in the vulnerable obese patient population.

Left ventricular (LV) longitudinal function is mechanically coupled to the elasticity of the ascending aorta (AA). The pathophysiologic link between stiff AA and reduced longitudinal strain and subsequent deterioration in longitudinal LV systolic function is likely relevant in heart failure with preserved ejection fraction (HFpEF). A proposed therapeutic effect of freeing the LV apex and allowing for LV inverse longitudinal shortening was studied in-silico utilizing Living Left Heart Human Model (Dassault Systémes Simulia Corporation). LV function was evaluated in a model with A) Elastic AA; B) Stiff AA; and C) Stiff AA with free LV apex. The cardiac model simulation demonstrated that freeing the apex caused inverse LV longitudinal shortening that can abolish the deleterious mechanical effect of a stiff AA on LV function. A stiff AA and impairment of LV longitudinal strain are common in patients HFpEF. The hypothesis-generating model strongly suggests that freeing the apex and inverse longitudinal shortening may improve LV function in HFpEF patients with a stiff AA.

Pulmonary hypertension (PH) is a progressive condition that affects pulmonary vessels, but its main prognostic factor is right ventricle (RV) function. Many mice/rat models are used for research in PAH, but results fail to translate in clinical trials. This study reviews studies that test interventions on pulmonary artery banding (PAB), a model of isolated RV disfunction, and PH models. Multiple tested drugs both improved pulmonary vascular hemodynamics in PH models and RV structure and function in PAB animals. PH models and PAB frequently exhibited similar results (73.1% concordance) with drugs other than endothelin receptor antagonists and phosphodiesterase inhibitors. RV systolic pressure accounted for most differences between PH models and PAB. On the other side, all results on RV fibrosis agreed (12 drugs). Macitentan, sildenafil and tadalafil improved most tested pathophysiological parameters in PH models, but almost none in PAB animals. Dapagliflozin was the only drug that improved no parameters. This review shows that many drugs currently under research for PAH have a cardioprotective effect on animals that may translate to humans. To improve the translational potential of drugs in this field, researchers should test them in multiple models, including PAB, while optimizing induction methods for human disease translation.

The technology of left ventricular assist devices (LVADs) requires developing and implementing an intelligent control systems to optimize pump speed to achieve a physiological metabolic demands for heart failure (HF) patients. This work aimed to present an advanced control algorithm to drive an LVAD under different physiological conditions. Pole placement method in conjunction with of sliding mode control approach (PP-SMC) was utilized to design and construct the proposed control method. In this design, the method was adopted to use neural networks to eliminate system uncertainties of disturbances. An elastance function was also developed and used as an input signal to mimic the physiological perfusion of HF patients. Two scenarios ranging from rest to exercise were introduced to evaluate the proposed technique. In this technique, a lumped parameter model of cardiovascular system (CVS) was used for this evaluation. The results demonstrated that the designed controller was robustly tracking the input signal in the presence of the system parameter variations of CVS. In both scenarios, the proposed method shows that the controller automatically drive the LVAD with a minimum flow of 1.7 L/min to prevent suction and 5.7 L/min to prevent over-perfusion.

Objective: One of the major causes of cerebral ventricular shunt failure is proximal catheter occlusion. We describe a novel ventricular cerebrospinal fluid (CSF) flow replicating system that assesses pressure and flow responses to varied degrees of catheter occlusion. Methods: Ventricular catheter performance was assessed during conditions of partial and complete occlusion. The catheters were placed into a three-dimensionally printed phantom ventricular replicating system. Artificial CSF was pumped through the ventricular system at a constant rate of 1 ml/min to mimic CSF flow, with the proximal end of the catheter in the phantom ventricle. Pressure transducer and flow rate sensors were used to measure intra-phantom pressure, outflow pressure and CSF flow rates. The catheters were also inserted into silicone tubing and pressure was measured in the same manner for comparison with the phantom. Results: Pressure measured in the phantom ventricle did not change when the outflow of the ventricular catheter was partially occluded. However, the intraventricular phantom pressure significantly increased when the outflow catheter was 100% occluded. Flow through the catheter showed no significant difference in rate with any degree of partial occlusion of the catheter. At the distal end of the partially occluded catheters, there was less pressure compared with the nonoccluded catheters. This difference in pressure in partially occluded catheters correlated with the percentage of catheter hole occlusion. Conclusions: Our model mimics physiological dynamics of the CSF flow in partially and completely obstructed ventricular catheters. We found that partial occlusion of the catheter had no effect on CSF flow rate, but did reduce outflow pressure of the catheter.

One of the operational challenges for the use of bentonite pellets as a sealing material in the abandonment of offshore fields consists in their disposition inside the well. This study aims to analyze the interaction of fluid media, consisting of saline solutions (NaCl, CaCl2 and KCl) and organic compounds (diesel, glycerin and olefin), with bentonite pellets, aiming its application as displacement fluid in offshore oil well abandonment operations. The physical integrity of the bentonite pellets in contact with the fluids was verified through visual inspections and dispersibility tests. Linear swelling tests were also performed to evaluate the potential for swelling of pellets in deionized water after contact with the fluid media. The results indicated that NaCl, CaCl2 and KCl solutions completely compromise the physical integrity of the pellets, while diesel and olefin showed the best responses regarding the structural preservation. Futhermore, the linear swelling tests showed that, even after the contact with diesel and olefin for 1 hour, bentonite pellets have reached a total swelling in water of 78%, after 24 hours. In this way, diesel and olefin proved to be highly promising alternatives to be used as displacement fluids for bentonite pellets in wells to be abandoned in a submarine environment.

Background: This study aimed to investigate the association between the internal derangement of the temporomandibular joint (TMJ), in particular the severity of disc displacement (DD), and the presence of generalized joint hypermobility (GJH) in growing patients evaluated on magnetic resonance images (MRI). The study also investigated the relationship between the stages of DD severity and age. Methods: This cross-sectional study has been conducted on a pre-orthodontic population (8-16 years). The GJH was assessed with the Beighton test (cutoff ≥ 4) and the final sample of 56 patients was divided into two groups: a Study Group, 30 subjects with GJH, and a Control Group, 26 subjects without GJH. The disc position was evaluated on MRI and the severity of DD was classified in four stages. Pearson's χ2 Test was performed for the analysis of the statistical correlation. Results: A statistically significant relationship between GJH and disc position was found, in particular a disc displacement with reduction (DDwR) and DD severity. It also emerged a positive association between the severity of DD and age, that increased with increasing age. Conclusions: Growing patients with GJH have a higher risk of developing DD and with more severe stages. The risk of developing DD and the severity increases with increasing age.

Currently the majority of studies on vision-based measurement has been conducted under ideal environments so that an adequate measurement performance and accuracy is ensured. However, vision-based systems may face some adverse influencing factors such as illumination change and fog interference, which can affect the measurement accuracy. This paper develops a robust vision-based displacement measurement method which can handle the two common and important adverse factors given above and achieve sensitivity at the subpixel level. The proposed method leverages the advantage of high-resolution imaging incorporating spatial and temporal context aspects. To validate the feasibility, stability and robustness of the proposed method, a series of experiments was conducted on a two-span three-lane bridge in the laboratory. The illumination change and fog interference are simulated experimentally in the laboratory. The results of the proposed method are compared to conventional displacement sensor data and current vision-based method results. It is demonstrated that the proposed method gives better measurement results than the current ones under illumination change and fog interference.

Since the introduction of Cross-laminated Timber (CLT) in Austria in the early 1990s, the adoption of this 90°-crosswise-laminated product has seen exponential growth worldwide. Compared to traditional laminated timber products (e.g. glulam), CLT provides improved dimensional stability, but with reduced out-of-plane bending stiffness. To improve the bending stiffness, while maintaining relative dimensional stability, a modified orientation of the inner layers in a diagonal direction can be used. This novel product is Diagonal-Cross-laminated Timber (DCLT), a composite timber product, consisting of inner layers which are rotated at different angle-ply orientations between 0 and 90 degrees to the outer layers. To properly model the out-of-plane bending behavior of the DCLT, analytical models and Finite Element Analysis (FEA) were used and the results were validated by third-point bending tests performed on DCLT panels with angle-ply orientations of 10°, 20°, 40°, 70°, and a conventional CLT 90° panel. The results indicate that DCLT panels with angle-ply cross-layers have a structural advantage in out-of-plane bending over traditional CLT (90°) panels. The development of DCLT and its introduction to the industry could enable the use of lower-quality timber that would not otherwise satisfy structural requirements for CLT.

Mapping building roof plane structures is an active research direction in urban-related studies, as understanding roof structure provides essential information for generating highly detailed 3D building models. Traditional deep learning models have been the main focus of most recent research endeavours aiming to extract pixel-based building roof plane areas from remote sensing imagery. However, significant challenges arise, such as delineating complex roof boundaries and invisible boundaries. Additionally, challenges during the post-processing phase, where pix-el-based building roof plane maps are vectorized, often result in polygons with irregular shapes. In order to address this issue, this study explores a state-of-the-art method for planar graph reconstruction applied to building roof plane extraction. We propose a framework for reconstructing regularized building roof plane structures using aerial imagery and cadastral information. Our framework employs a holistic edge classification architecture based on an attention-based neural network to detect corners and edges between them from aerial imagery. Our experiments focused on three distinct study areas characterized by different roof structure topologies: Stadsveld – 't Zwering neighbourhood and Oude Markt area, located in Enschede, The Netherlands, and the Lozenets district in Sofia, Bulgaria. The outcomes of our experiments revealed that a model trained with a combined dataset of two different study areas demonstrated superior performance, capable of delineating edges obscured by shadows or canopy. Our experiment in the Oude Markt area resulted in building roof plane delineation with an F-score value of 0.43 when the model trained on the combined dataset was used. In comparison, the model trained only on the Stadsveld – 't Zwering dataset achieved an F-score value of 0.37, and the model trained only on the Lozenets dataset achieved an F-score value of 0.32. The results from the developed approach are promising and can be used for 3D city modelling in different urban settings.

With the increased use of simulation based training using animal models for the education of surgical and anaesthetic techniques, an increased understanding of the anatomy of such models and how they compare to humans is required. The transversus abdominis plane block is a regional anaesthetic technique that requires an understanding of the abdominal wall anatomy along with proficient ultrasound use. The current review aims to compare the anatomy of the abdominal wall across species, particularly focussing on the pertinent differences within the class of mammals, and secondarily, it aims to address the implications of these differences for simulation based training of the transversus abdominis plane block. To achieve this, the PubMed, Web of Science and Google Scholar databases were searched for relevant literature. The mammalian abdominal wall differs in its musculature, vasculature or innervation from that of amphibians, birds or reptiles, however, among species of mammals, the structure of the abdominal wall follows a similar framework. Particular differences among mammals include the additional muscular layer of the panniculus carnosus found in most mammals other than humans, the variable arterial origins and dominant vascular supply of the abdominal wall and the number of thoracolumbar nerves innervating the abdominal wall. When using animal models for simulation based training, the pig is recommended for the transversus abdominis plane block given its closely homologous abdominal wall structure, availability and larger comparative size.