The paper explores the features of numerical simulation to analyze the dynamic behavior of drives controlled by pulse-width modulators. Modern motor control systems widely use pulse width modulation. Effective numerical modeling of such systems has specific features because the models employed are continuous-event and have hybrid behavior due to the presence of nonlinear links with discontinuities of the first kind. Therefore, it is essential to have special integration methods with variable steps, which should be factored in when developing the model. The paper shows how these problems are solved when modeling an electric drive with a DC motor in the SimInTech software.

Introduction. Anesthesia is widely used in various fields of dentistry to reduce patient discomfort when the treatment would be painful. The dentist may need to infiltrate the anesthetic into multiple locations and this is usually done with the same needle which passes through the soft tissues several times to distribute the anesthetic solution over a larger area. The present study aims to evaluate, through a morphological analysis under a scanning electron microscope (SEM), how the beveled tip of a 30G needle, used to inject anesthetic several times into different areas of the vestibular mucosa, changes. Materials and methods. 30G needles with two different brands were tested, in vivo used for a variable number of sequential injections from 1 to 6 on 192 patients. The specimens were analyzed under SEM observation to evaluate any deformations induced by contact with the vestibular soft tissues. Results. The amount of deformation, measured along the axis parallel to the needle, was proportional to the number of injections. The protrusion of deformations, measured on an axis perpendicular to the needle, were maximum on the needles used 3 times. For the needles used 4,5 and 6 injections, no further increase in deformations was noted. Conclusion. From the data it seems that the tested needles are not produced to withstand multiple injections consequently after the first injection on soft tissues, they undergo a deformation which could increase the risk of injury to the mucosa itself or to nerves and vessels with which they come into contact. It would be advisable to use the single needle for a reduced number of injections.

Despite the growing capabilities of large language models, concerns exist about the biases they develop. In this paper, we propose a novel, automated mechanism for debiasing through specified dataset augmentation in the lens of bias producers that can be useful in a variety of industries, especially ones that are “restricted” and have limited data. We consider that bias can occur due to intrinsic model architecture and dataset quality. The two aspects are evaluated using two different metrics we created. We show that our dataset augmentation algorithm reduces bias as measured by our metrics.

Accurate traffic simulation models play a crucial role in developing intelligent transport systems that offer timely traffic information to users and efficient traffic management. However, calibrating these models to represent real-world traffic conditions accurately poses a significant challenge due to the dynamic nature of traffic flow and the limitations of traditional calibration methods. This article introduces a machine learning-based approach to calibrate macroscopic traffic simulation models using real-time traffic video stream data. By leveraging computer vision technologies to extract key traffic parameters from video streams, the approach demonstrated a notable improvement in aligning the generated data from the calibrated simulation model with car sensor data, achieving an average improvement of over 50% compared to the uncalibrated macroscopic model. Moreover, there was a substantial reduction in data drift for the machine learning model integrated into the virtual transport space using vehicle-to-everything technology, resulting in a more than fourfold decrease in the average absolute error of the model.

Trichomonas vaginalis is an extracellular parasite protozoan that causes human trichomoniasis, a sexually transmitted infection (STI) that affects approximately 200 million people worldwide. The presence of T. vaginalis adhesion to inert substrates has been described in several reports. Still, very few studies on cluster formation and more detailed analyses of the contact regions between the membranes of the parasites in these aggregate formations have not been carried out. We analyzed the formation of parasite monolayers and clusters using high-resolution scanning electron microscopy, transmission electron microscopy, cytochemistry, TEM tomography, and dye injection. Here, we show the formation of a monolayer of tightly adherent cells, epithelium-like, when the parasites are in contact with an inert material. Based on this observation, we analyzed whether this monolayer behaves as an epithelium, analyzing cell junctions, cell communication, and ultrastructural aspects. We also analyzed the cluster formation and the morphological characteristics of parasite aggregation observed in the culture supernatant. We report that monolayer formation differs from cluster formation in many aspects. The monolayers form strong adhesion, whereas the clusters have fragile attachments. There is no fusion or passage of molecules between neighbor-attached cells; there is no need for different strains to form filopodia, cytonemes, and extracellular vesicles during cluster formation.

Automated charging technologies are becoming increasingly important in the electrification of heavy road freight transport, especially in combination with autonomous driving. This study provides a comprehensive analysis of automated charging technologies for electric heavy-duty vehicles (HDVs). It encompasses the entire spectrum of feasible technologies, including static and dynamic approaches, with each charging technology evaluated for its advantages, potentials, challenges, and technology readiness level (TRL). Static conductive charging methods such as charging robots, underbody-couplers or pantographs show good potential, with pantographs being the most mature option. These technologies are progressing towards higher TRLs, with a focus on standardization and adaptability. While static wireless charging is operational for some prototype solutions, it encounters challenges related to implementation and efficiency. Dynamic conductive charging through an overhead contact line or contact rails holds promise for high-traffic HDV routes with the overhead contact line being the most developed option. Dynamic wireless charging, although facing efficiency challenges, offers potential for seamless integration into roads and minimal wear and tear. Battery swapping is emerging as a practical solution to reduce downtime for charging, with varying levels of readiness across different implementations. To facilitate large-scale deployment further standardization efforts are required. The study emphasizes the necessity for continued research and development to enhance efficiency, decrease costs, and ensure seamless integration into existing infrastructures. Technologies that achieve this best will have the highest potential to significantly contribute to the creation of an efficiently automated and environmentally friendly transport sector.

This study explores the transformative potential of integrating Building Information Modeling (BIM) and Generative Design methodologies in heritage conservation and building management. By utilizing BIM, detailed architectural, structural, and MEP models were created, facilitating precise design and effective stakeholder collaboration. Generative Design enabled the exploration of multiple design solutions, optimizing spatial layouts and structural integrity. The project also integrated automated management systems and IoT sensors to enhance real-time monitoring, energy efficiency, and user comfort through the development of a digital twin. Despite encountering challenges such as technical complexities and budget constraints, the project successfully preserved the cinema's historical essence while incorporating modern functionalities. The findings highlight the contributions of BIM and Generative Design to the AEC industry, emphasizing their role in improving design accuracy, operational efficiency, and sustainability. This research provides valuable insights for future projects in heritage conservation, offering a blueprint for balancing historical preservation with contemporary needs. The revitalization of the "Ex Cinema Santa Barbara" in Paternò exemplifies these advancements, demonstrating how these technologies can restore and modernize culturally significant historical buildings effectively.

Digital photogrammetry has attracted widespread attention in the field of geotechnical and geological survey due to its low-cost, ease of use and contactless mode. In this work, with the purpose of studying the progressive block surficial detachments of a landslide we developed a monitoring system based on fixed multi-view time-lapse cameras. Thanks to a new-developed photogrammetric algorithm based on the comparison of photo sequences through a structural similarity metric and the computation of the disparity map of two convergent views we can quickly detect the occurrence of collapse events, determine their location and calculate the collapse volume. With the field data obtained at the Perarolo landslide site (Belluno Province, Italy), we have preliminary tested the effectiveness of the algorithm and its accuracy in the volume calculation. The method of quickly and automatically obtaining collapse information proposed in this paper can extend the potentials of landslide monitoring system based on videos or photo sequence and it will be of great significance for further research on the link between the frequency of collapse events and the driving factors.

PET imaging of bacterial infection could potentially provide added benefit for patient care by non-invasive means. [68Ga]Ga-desferrioxamine B – a radiolabelled siderophore – shows specific uptake by human-pathogenic bacteria like Staphylococcus aureus or Pseudomonas aeruginosa as well as sufficient serum stability for clinical application. Here, we provide data for automated production of [68Ga]Ga-desferrioxamine B on two different cassette based synthesis modules (Modular-Lab PharmTracer and GRP 3V) using commercially available cassettes together with an approved 68Ge/68Ga radionuclide generator. Quality control including determination of radiochemical purity as well as a system suitability test was set up via RP-HPLC on a C18 column. The two described production processes, using an acetic acid/acetate buffer system with ascorbic acid as a radiation scavenger for radiolabelling, yield ready-to-use formulations with sufficient activity yield. Batch data showed radiochemical purity of >95 % as determined by RP-HPLC and ITLC as well as excellent stability over 2 hours post production. Specifications for routine production were set up and validated with four master batches for each synthesis module. Based on this study, an academic clinical trial for imaging of bacterial infection was initiated. Both described synthesis methods enable reproducible, automated in-house production of [68Ga]Ga-desferrioxamine B for clinical application.

Okra, a widely grown vegetable in many regions, often suffers from freshness loss during transportation, causing significant waste. Factors like variety, environment, maturity, and handling affect its quality. Current methods for checking okra tenderness are slow and prone to mistakes, so we need a better, non-damaging method. This study aims to use a device on a robot arm to assess okra freshness and tenderness. We tested 120 okra pods, storing some in a cold chamber for 24 hours (considered tender) and others at room temperature for two days before moving them to a cold environment for five more days (considered not tender). We used a force sensor on a robot arm to measure okra hardness without damaging it, then did tenderness tests. We found that certain sensor data, like the first slope (S1) and the difference between the maximum value and the first overshoot (Os), were good predictors of tenderness, with an accuracy rate of nearly 80%. We also validated this non-damaging method with weight loss, compression, and puncture tests, achieving a 95.5% accuracy rate in distinguishing between tender and non-tender okra pods.

Transportation plays an important role in urban development. Population growth and environmental burden have turned the efforts of cities globally towards smarter and greener mobility. Cooperative and Connected Automated Mobility (CCAM) serves as a concept with the power and potential to help achieve these goals building upon technological fields like Internet of Things, computer vision and distributed computing. However, its implementation is hindered by various challenges covering technical parameters such as performance and reliability in tandem with other issues, such as safety, accountability and trust. To overcome these issues, new distributed and decentralized approaches like blockchain and smart contracts are needed. This paper aims at identifying a comprehensive inventory of CCAM challenges and use it as a framework to describe methodologies using blockchain and smart contracts to address them. It provides a comparative analysis of the findings to draw useful conclusions and discuss future directions in CCAM and relevant blockchain applications. The paper contributes to intelligent transportation systems’ research by offering an integrated view of the difficulties in substantiating CCAM and providing insights on the most prominent blockchain and smart contract technologies that tackle them.

The supply chain has incorporated products by putting them into hair scarfs. This study introduces the use of mini chips in health and beauty products and can reduce fatigue through enhanced sleep patterns. The mini chip could be placed in the scarf and used as a prototype. RFID technology provides the supply chain with specific information that is used to identify products and make communication easier. (Muhammad, et. al. 2013) This paper presents a new tool herein referred to as a scarf prototype which is developed to analyse EMG (electromyogram), ECG (electrocardiography), EEG (electroencephalogram), and EOG (electro-oculogram) signals that focuses in the area of sleep disorders. The mini chips used can be used to determine a solution for sleep disruption by using automated analytics. This could lead to improvement in our understanding of sleep disruption and overall sleep physiology. Automated technology allows repeated measurements, evaluation of sleep patterns, and provide suggestions to improve a person’s quality of sleep. This analysis compares the use of polysomnography and the scarf prototype. The analytics provide models and shows correlation between variables, such as EMG, ECG, EEG, and EOG. This study shows that the results from the scarf prototype is just as reliable as the original method, polysomnography.

Building sustainable campuses has become a priority for various higher education institutes (HEIs). Internalization is one of the important tasks in the progress. Therefore, attracting and maintaining international faculty has converted to action for various internationalized campuses. During the COVID-19 pandemic, it has impacted most of the citizens’ life, while the international faculty members’ life might be tight during this period. The purpose of this study is to explore the perspectives of international faculty members on their life in higher education institutes by using partial least square structural equation modeling (PLS-SEM). Using a self-compiled online survey, we invited 80 international faculty members of HEIs in Taiwan to investigate this issue. The survey covers career and professional status, teaching and research status, and demographics of the faculty. This study proposes a novel conceptual framework for addressing international faculty’s campus life, the design will examine the relationships among working conditions, views of institutions, views of government’s measures, and levels of satisfaction through PLS-SEM. The demographic profile of the participants revealed (a) most international faculty are employed full-time as lecturers or assistant professors in most public universities; (b) most international faculty members earned their first degree outside of Taiwan; however, 66% of them earned their post-doctoral degrees in Taiwan. The results of PLS-SEM suggest that the international faculty perspective of government is more directly related to their current work satisfaction and overall satisfaction. The designed model has shown work well to assess this issue. This can be extended to other higher education settings to tackle similar issues.

The Cordoba Guitar Festival is one of the most important cultural events in Spain. This article analyses the musical preferences, satisfaction, attitudinal loyalty and behavioural loyalty of spectators who attended the 36th festival held in July 2016, as well as the festival’s economic impact on the city. To achieve this aim, a structural equation model (SEM) was used. The results show the goodness-of-fit of the model and indicate that the observed data fit the expected dataset.

Identification of costs drivers and their influence level on building development costs play a key role in the development of construction models and improve the efficiency and effectiveness of any project. Forty-five indicators influencing building development costs in New Zealand are explored by literature review and pilot interviews. These indicators are grouped into seven categories. The determination and ranking of the cost drivers are carried out by a questionnaire survey distributed to key professionals working in New Zealand’s construction industry. Structural equation modeling (SEM) software was employed for analysis of the collected data. One of the key advantages of this powerful software is to provide the p-value according to the structure of the research model. Findings of this study indicate that the property market and construction industry factor, statutory and regulatory factor, and socio-economic factor are major factors affecting building development costs in New Zealand.

The blood count is crucial for assessing bone marrow's cell production and differentiation during infections, gauging disease severity, and monitoring therapeutic responses. The profile of blood count in chronic form of paracoccidioidomycosis (PCM) has been insufficiently explored. To better understand the changes in hematological cells in different stages of the PCM chronic form, we evaluated the blood count, including immature blood cells in automated equipment, before and during the treatment follow-up of 62 chronic PCM patients. Predominantly male (96.8%) with an average age of 54.3 (SD 6.9) years, participants exhibited pre-treatment conditions such as anemia (45.2%), monocytosis (38.7%), and leukocytosis (17.7%) which became less frequent after clinical cure. Anemia was more prevalent in severe cases. Notably, hemoglobin and reticulocyte hemoglobin content increased, while leukocytes, monocytes, neutrophils, immature granulocytes, and platelets decreased. Chronic PCM induced manageable hematological abnormalities, mainly in the red blood series. Monocytosis, indicating monocytes' role in PCM's immune response, was frequent. Post-treatment, especially after achieving clinical cure, significant improvements were observed in various hematological indices, including immature granulocytes and reticulocyte hemoglobin content, underscoring the impact of infection on these parameters.

The carbonized elastomer-based composites (CECs) possess a number of attractive features in terms of thermomechanical and electromechanical performance, durability in aggressive media and facile net-shape formability, but their relatively low ductility and strength limit their suitability for structural engineering applications. Prospective applications such as structural elements of MEMS can be envisaged, since smaller principal dimensions reduce the susceptibility of components to residual stress accumulation during carbonization, and to brittle fracture in general. We report the results of operando in-SEM study of micro-deformation and fracture behavior of CECs based on NBR elastomeric matrices filled with carbon and silicon carbide. Nanostructured carbon composite materials were manufactured via compounding of elastomeric substance with carbon and SiC fillers using mixing rolling mill, vulcanization, and low-temperature carbonization. Double Edge Notched Tensile (DENT) specimens of vulcanized and carbonized elastomeric composites were subjected to in situ tensile testing in the chamber of the scanning electron microscope (SEM) Tescan Vega 3 using Deben Microtest 1 kN Tensile Stage. The series of acquired SEM images were analyzed by means of Digital Image Correlation (DIC) using Ncorr open source software to map the spatial distribution of strain. These maps were correlated with Finite Element Modelling (FEM) simulations to refine the values of elastic moduli. Besides, the elastic moduli were derived from unloading curve nanoindentation hardness measurements carried out using NanoScan-4D tester and interpreted using the Oliver-Pharr method. Carbonization causes significant increase of elastic moduli from 0.86 ± 0.07 to 14.12 ± 1.20 GPa for the composite with graphite and carbon black fillers. Nanoindentation measurements yield somewhat lower values, namely, 0.25 ± 0.02 GPa and 9.83 ± 1.10 GPa before and after carbonization respectively. The analysis of fractography images suggests that crack initiation, growth and propagation may occur both at the notch stress concentrator and relatively far from the notch. Possible causes of such response are discussed, namely, (1) residual stresses introduced by processing; (2) shape and size of fillers; and (3) the emanation and accumulation of gases in composites during carbonization.

Scanning electron microscopy (SEM) is a powerful tool in the domain of material science, mining, and geology, owing to its enormous potential to provide unique insights into the micro and nanoscale worlds. This comprehensive review discusses the background development of SEM, basic SEM operation including the specimen preparation and imaging process, and fundamental theoretical calculations underlying the SEM operation. It provides foundational understanding to the engineers and scientists, who never got a chance to dig in-depth into the SEM, to understand the working and development of this robust analytical technique. The present review covers how SEM has been serving as a crucial tool in mineral characterization, with specific discussions on the working and research fronts of SEM-EDX, SEM-AM, SEM-MLA, and QEMSCAN. With automation gaining pace in the development of all spheres of technology, the understanding of uncertainties in SEM measurements is very important. The constraints in mineral phase identification by EDS spectra and sample preparation are conferred. In the end, future research directions for SEM are analyzed with the possible incorporation of machine learning, deep learning, and artificial intelligence tools, for automating the process of mineral identification, quantification, and efficient communication with the researchers, so that the analytical process robustness and objectivity can be improved, and the analysis time and the involved costs can be brought down. This review also discusses the idea of integrating robotics with SEM, to make the equipment portable, so that further mineral characterization insights can be gained not only on earth but also on other terrestrial grounds.

A description is provided of a method -- the Set Equality Method (SEM) -- to determine the validity, or lack of validity, of each categorical syllogism. A justification is given for the presentation of a new method to solve a problem which has already been solved using different approaches. First, the SEM assigns an equality of certain sets (or two of those equalities in specific cases as will be indicated) to each of the categorical propositions composing each syllogism considered -- that is, to each of the two premises and to the conclusion. Each syllogism considered is valid if and only if a) it is possible to select one of those equalities corresponding to one of the premises such that one of its members is a certain set and the other of those equalities corresponding to the other premise such that one of its members is a subset of the set mentioned, and b) it is possible to deduce an equality corresponding to the conclusion of the two equalities corresponding to the premises. In some cases, as will be specified, it is possible to provide a second test for the validity of a syllogism whose validity was already proven, thus providing information about the logical form of categorical syllogisms.

The chicken poultry business is becoming a crucial sector for our nation's sustainable food supply. To increase the health of chickens in coops and maybe increase the output of chicken meat and eggs, several innovations and inventions have been developed. Therefore, the creation of an automated chicken feeding device might be highly beneficial for the expansion of the poultry sector. This equipment may take the role of a worker in the chicken feeding process, solving the industry's labor shortage and introducing a semi-automatic procedure. The main processor of the automated chicken feeding system is a Raspberry Pi 3 Model B+. The machine consists of five main components: a Raspberry Pi with an amplifier that makes noise to draw the attention of free-range chickens, a Raspberry Pi with a pi camera that counts and detects the chickens, a Raspberry Pi with a servomotor that moves the food from storage to a container, a Raspberry Pi with a load cell that controls the number of feeds to avoid waste on foods, and a Raspberry Pi with a temperature sensor that monitors the food's freshness. This enhances the coop's atmosphere while lowering labor costs, conserving food, and ensuring that the chickens are fed on time. It also regulates the temperature sensor to ensure that the chicken food is fresh and prevents food from becoming polluted by insects and chicken excrement.

The inhibition of localised corrosion is known to involve multiple processes taking place over a range of time and length scales that are difficult to study by conventional electrochemical methods. This work demonstrates an approach to probing complex localised electrochemical processes by combining an electrochemically integrated multi-electrode array (also known as wire beam electrode (WBE)), scanning vibrating electrode technique, scanning electrochemical microscopy and surface analytical techniques. Each technique reveals certain aspects of the dynamically changing, multi-scale, inhibitor-microstructure interactions and local chemistry over a heterogeneous AA2024-T3 alloy surface in the presence of an environmentally friendly inhibitor; cerium diphenyl phosphate (Ce(dpp)3).

Fintech's emergence is one of the most significant developments in finance, and its application has been of much interest and popularity in recent decades. This study aims to explore the adoption of fintech in emerging economies by employing a structural equation model. The study's sample population consists of bank clients of Ethiopian commercial banks who have used financial technology platforms for at least one year. The total number of sample sizes is 440. The data collection instrument used for this study is a questionnaire (seven-point likert scales ranging from strongly disagree to strongly agree). Structural equation model (SEM) analysis was implemented using Amos software to examine the relationship between variables. The findings of the study support the hypotheses that various factors, including performance expectancy, effort expectancy, social influence, facilitating condition, traliaility, and user innovativeness, significantly influence the adoption and usage of fintech services. The study recommends that FinTech companies implement pilot programs to allow potential users to trial FinTech services on a limited basis before full commitment. Fintech industries should engage with local communities through events, seminars, and workshops to introduce fintech services. Having community leaders and respected individuals advocate for the technology can enhance acceptance.

3D-printed aluminium alloy fabrications made by selective laser melting (SLM) offer a promising route for the production of small series of custom-designed heat exchangers with complex geometry and shape and miniature size. Alloy composition and printing parameters need to be optimized to mitigate fabrication defects (pores and microcracks) and enhance the part performance. The deformation response needs to be studied with adequate characterization techniques at relevant dimensional scale capturing the peculiarities of micro-mechanical behavior relevant to the particular article and specimen dimensions. Purposefully designed Al-Si-Mg 3D-printable RS-333 alloy was investigated with a number of microscopy techniques including in situ mechanical testing with a Deben Microtest 1 kN stage integrated and synchronized with Tescan Vega3 SEM to acquire high resolution image datasets for Digital Image Correlation (DIC) analysis. Dog bone specimens were 3D-printed in different orientation of gauge zone cross-section with respect to the fast laser beam scanning and growth directions. This corresponds to varying local conditions of metal solidification and cooling. Specimens show variation in mechanical properties, namely, Young’s modulus (65…78 GPa), yield stress (80–150 MPa), ultimate tensile strength (115–225 MPa) and elongation at break (0,75–1,4 %). Furthermore, the failure localization and character was altered with the change of gauge cross-section orientation. DIC analysis allowed correct strain evaluation that overcame the load frame compliance effect and helped to identify the unevenness of deformation distribution (plasticity waves) that ultimately resulted in exceptionally high strain localization near the ultimate failure crack position.

Copper-nitride (Cu3N) material is attracting much attention as a potential next-generation thin-film solar-light absorber. In this work, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron sputtering, at room temperature,onto glass and silicon substrates. The optical properties of the Cu3N thin layers were studied by spectroscopic ellipsometry and transmission, to achieve a low-cost absorber material to replace conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by FIB-SEM microscopy and FTIR spectroscopy.

Fragile X syndrome (FXS) is caused by the full mutation in the FMR1 gene on the Xq27.3 chromosome region. It is the most common monogenic cause of Autism Spectrum Disorder (ASD) and inherited intellectual disability (ID). Besides ASD, ID and other issues, individuals with FXS may exhibit sleep problems and impairment of circadian rhythm (CR). The Drosophila melanogaster models of FXS, such as dFMR1B55, present excellent model for research in the FXS field. During this study, sleep pattern and CR in dFMR1B55 mutants were analyzed, using a new platform based on continuous high-resolution videography in integration with a highly-customized version of software. This methodology provides more sensitive results, which could be crucial for all further research in this model of fruit flies. The study revealed that dFMR1 B55 male mutants can be considered weak rhythmic flies rather than totally arrhythmic, and present a good alternative animal model of genetic disorder, which includes impairment of CR and sleep behavior. The combination of videography and software used in the current study should be recommended as a gold-standard methodology for such further research.

This paper aims to propose improvements for plastic waste management in Salvador – the Brazilian third most populated metropolis – via Partial Least Squares Structural Equation Modeling (PLS-SEM). All indicators, constructs, and hypotheses regarding collection, sorting, recycling, and disposal in the proposed PLS model were derived from the literature review, and the dependence of the performance construct on efficiency, effectiveness, municipality's socioeconomic aspects and municipality infrastructure is evaluated. Academic and practitioner publics were surveyed, and after analysis in both SmartPLS and RStudio software, suggestions for improvement regarding plastics recycling rate, market maturity, and infrastructural aspects for optimized reverse logistics were made. Since almost double the minimum number of respondents answered the survey questionnaire and the PLS-SEM statistics showed that the modeling presents consistency, the discussion is relevant. The model can and will evolve, but examples of suggested improvement are the installation of Deposit-Return Systems (DRS) in parks, streets, and avenues for increasing selective collection and the direct purchasing of waste from residents by municipal administration, compensating them with vouchers for food. The model can be a basis for other cities worldwide sharing analogous characteristics. By considering it, organizations can contribute to both reduced Greenhouse Gas (GHG) emissions and reduced terrestrial pollution.

To encourage proper waste management from electrical and electronic devices (e-waste), it is necessary to invest heavily in the development of recycling technologies. One way to improve the process is to automate separating the shredded parts of e-waste using a robot. This paper's literature review, utilizing the Preferred Reporting Items for Systematic reviews and Meta-Analyses (PRISMA) framework, showcases potential robotic technologies for e-waste separation. However, the intricate design of these devices can pose significant challenges in their implementation. Various legal, organizational, and sociological obstacles have left Serbia's e-waste management practice underdeveloped, resulting in an unsatisfactory recycling rate. In this paper we examined the possibility of using robots on the precise example of recycling refrigerators in a recycling center in Eastern Serbia, concluding that such a solution would have multiple positive effects, both on the employees and the working environment, on the operations of the recycling center itself, and on increasing the e-waste recycling rate in the country.

Recent technological advancements in conservation genetics and genomics have resulted in diverse tools for aiding conservation of species. The precision and resolution of high throughput sequencing technologies provide valuable insights to aid conservation decisions, but these technologies are often financially unfeasible or unavailable in resource constrained countries. Inter-Simple Sequence Repeat (ISSR) markers, when combined with sensitive automated detection systems, provide a simple, cheap means to investigate genetic diversity and discriminate closely related species. Here we apply this technology to assess genetic diversity and taxonomic delimitation in the Encephalartos eugene-maraisii species complex, a highly threatened, taxonomically dubious group of cycads in South Africa. Our analyses support taxonomic singularity of E. dyerianus, E. dolomiticus and E. eugene-maraisii. Relationships between E. nubimontanus and E. cupidus remain uncertain. E. middelburgensis samples showed no clustering but had poor amplification success. This study demonstrates the suitability of automated ISSR fingerprinting as a method for plant conservation studies, especially in resource-constrained countries, and we make recommendations as to how this methodology can be effectively implemented.

Timely and accurate identification of change detection for areas depicted on nautical charts constitutes a key task for marine cartographic agencies in supporting maritime safety. Such a task is usually achieved through manual or semi-automated processes, based on best practices developed over the years requiring a substantial level of human commitment (i.e., to visually compare the chart with the new collected data or to analyze the result of intermediate products). This work describes an algorithm that aims to largely automate the change identification process as well as to reduce its subjective component. Through the selective derivation of a set of depth points from a nautical chart, a triangulated irregular network is created to apply a preliminary tilted-triangle test to all the input survey soundings. Given the complexity of a modern nautical chart, a set of feature-specific, point-in-polygon tests are then performed. As output, the algorithm provides danger-to-navigation candidates, chart discrepancies, and a subset of features that requires human evaluation. The algorithm has been successfully tested with real-world electronic navigational charts and survey datasets. In parallel to the research development, a prototype application implementing the algorithm was created and made publicly available.

Pharmacy personnel often answer telephones to respond to pharmacy customers (subjects) who received messages from automated systems. This research examines the communication process in terms of how users interact and engage with pharmacies after receiving automated messages. No study has directly addressed automated telephone calls and subjects’ interactions. The purpose of this study is to test the interpersonal communication (IC) process of uncertainty in subjects in receipt of automated telephone calls from pharmacies. Subjects completed a survey of validated scales for Satisfaction (S); Relevance (R); Quality (Q); Need for Cognitive Closure (NFC). Relationships between S, R, Q, NFC, and subject preference to an automated telephone call (ATC) were analyzed to determine whether subjects contacting pharmacies display information seeking behavior. This research demonstrates that seeking information occurs if subjects: are dissatisfied with the content of the ATC; perceive that the Q of the ATC is high; perceive that the Q of ATC is high, and like receiving the ATC or with high NFC, and do not like receiving ATCs. Other interactions presented complexities amongst uncertainty and tolerance of NFC within the IC process.

Some studies have demonstrated that in vivo degradation processes are influenced by the material’s physico-chemical properties. The present study compares two hydroxyapatites manufactured on an industrial scale, deproteinized at low and high temperatures, and how physico-chemical properties can influence the mineral degradation process of material performance in bone biopsies retrieved 6 months after maxillary sinus augmentation. Residual biomaterial particles were examined by field scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX) to determine the composition and degree of degradation of the bone graft substitute material. According to the EDX analysis, the Ca/P ratio significantly lowered in the residual biomaterial (1.08±0.32) compared to the initial composition (2.22±0.08) for the low-temperature sintered group, which also presented high porosity, low crystallinity, low density, a large surface area, and poor stability and a high resorption rate compared to the high-temperature sintered material. This demonstrates that variations in the physico-chemical properties of bone substitute material clearly influence the degradation process. Further studies are needed to determine whether the resorption of deproteinized bone particles proceeds slowly enough to allow sufficient time for bone maturation to occur.

Amazon Web Services (AWS) instances provide a convenient way to run training on complex ’omics data analysis workflows without requiring participants to install software packages or store large data volumes locally. However, efficiently managing dozens of instances is challenging for training providers. We present a set of Bash scripts that make it quick and easy to manage Linux AWS instances pre-configured with all the software analysis tools and data needed for a course, and accessible using encrypted login keys and optional domain names. Creating over 30 instances takes 10-15 minutes. A comprehensive online tutorial describes how to set up and use an AWS account and the scripts, and how to customise AWS instance templates with other software tools and data. We anticipate that others offering similar training may benefit from using the scripts regardless of the analyses being taught.

Urban transportation in the next few decades will shift worldwide towards electrification and automation, with the final aim of increasing energy efficiency and safety for passengers. Such a big change requires strong collaboration and efforts among public administration, research and stakeholders in developing, testing and promoting these technologies in the public transportation. Working in this direction, in the present work the impact of the introduction of driverless electric minibuses, for the first and last mile transportation, in the public service is studied. More specifically, this paper covers a state of the art in terms of technological background for automation, energy efficiency via electrification, and the current state of the legal framework in Europe with focus on the Baltic Sea Region.

Copper-nitride (Cu3N) semiconductor material is attracting much attention as a potential, next-generation thin-film solar-light absorber in solar cells. In this communication, polycrystalline Cu3N thin films were prepared using reactive-RF-magnetron-sputtering deposition, at room temperature, onto glass and silicon substrates. The very-broadband optical properties of the Cu3N thin film layers were studied by UV-MIR (0.2-40 μm) ellipsometry and optical transmission, to be able to achieve the goal of a low-cost absorber material to replace the conventional silicon. The reactive-RF-sputtered Cu3N films were also investigated by focused ion beam scanning electron microscopy, and both FTIR and Raman spectroscopies.

This article presents an automated vision-based algorithm for the die-scale inspection of wafer images captured using scanning acoustic tomography (SAT). This algorithm can find defective and abnormal die-scale patterns, and produce a wafer map to visualize the distribution of defects and anomalies on the wafer. The main procedures include standard template extraction, die detection through template matching, pattern candidate prediction through clustering, and pattern classification through deep learning. To conduct the template matching, we first introduce a two-step method to obtain a standard template from the original SAT image. Subsequently, a majority of the die patterns are detected through template matching. Thereafter, the columns and rows arranged from the detected dies are predicted using a clustering method; thus, an initial wafer map is produced. This map is composed of detected die patterns and predicted pattern candidates. In the final phase of the proposed algorithm, we implement a deep learning-based model to determine defective and abnormal patterns in the wafer map. The experimental results verified the effectiveness and efficiency of our proposed algorithm. In conclusion, the proposed method performs well in identifying defective and abnormal die patterns, and produces a wafer map that presents important information for solving wafer fabrication issues.

The rapid evolution of information and communication technologies, notably the Internet, has yielded substantial benefits while posing challenges to information system security. With an increasing frequency of cyber threats—from unauthorized access to data breaches—the digital landscape's vulnerability is evident. Addressing the financial impact of cybercrime, this study delves into the role of Artificial Intelligence (AI) and Machine Learning (ML) technologies in cybersecurity. Analyzing advancements and outcomes, the research explores practical techniques for anomaly detection, threat prediction, and automated response. By investigating prior research and real-world implementations, the study provides valuable insights into the potential of AI/ML, uncovering current trends, challenges, and prospects in enhancing cybersecurity tactics amid a dynamically changing threat landscape.

The capability of extracting information and analyze it into a common format is essential for performing predictions, comparing projects through cost benchmarking, and for having a deeper understanding of the project costs. However, the lack of standardization and the manual inclusion of the data makes this process very time-consuming, unreliable, and inefficient. To tackle this problem, a novel approach with a big impact is presented combining the benefits of data mining, statistics, and machine learning to extract and analyze the information related to railway costs infrastructure data. To validate the suggested approach, data from 23 real historical projects from the client network rail was extracted, allowing their costs to be comparable. Finally, some machine learning and data analytics methods were implemented to identify the most relevant factors allowing for costs benchmarking. The presented method proves the benefits of data extraction being able to gather, analyze and benchmark each project in an efficient manner, and deeply understand the relationships and the relevant factors that matter in infrastructure costs.

Crack inspection is important to monitor the structural health of pavement structures and to facilitate an easier rehabilitation process. Currently, pavement crack inspection is conducted manually, which is inefficient and costly at the same time. For solving the problem, this work has developed a robotic system for automated data collection and analysis in real-time. The robotic system navigates on the pavement and collects visual images from the surface. A deep learning-based semantic segmentation framework named RCDNet was proposed and implemented on the onboard computer of the robot to identify cracks from the visual images. Simulation results show that the deep learning model obtained 96.29% accuracy for predicting the images. The proposed robotic system was tested on both indoor and outdoor environments and was observed that it can complete inspecting a 3m × 2m grid within 10 minutes and a 2.5m × 1m grid within 6 minutes. This outcome shows that the proposed robotic method can drastically reduce the time of manual inspection. Furthermore, a severity map based on the results from visual images was also generated to provide an idea of which locations should be paid more attention to repair in a test grid.

.Most of the accident cases at work are caused by unsafe behaviour. Scholars have thus extensively researched factors of safe behavior.Safety leadership is stated as the most effective factor in safety behaviour. Besides, safety knowledge and safety attitudes are also found to influence safety behaviour. The purpose of this paper is to investigate the nature of the relationship between safety leadership, safety knowledge, safety attitude, and safety behavior, which has been found to be limited or rare in previous research.A self-administered questionnaire was applied and was distributed randomly to 140 SME manufacturing workers and they were analysed using the structural equation modelling partial least squares (PLS-SEM). The results prove that safety leadership has a significant effect on safety knowledge, safety attitude, and safety behaviour, with safety knowledge and safety attitude mediating the safety leadership-safety behaviour relationship. Consequently, the results provide a more in-depth view of the relationship between safety leadership and safety knowledge-attitude-behaviour via adapting social-cognitive theory and social learning theory in solving safety issues in SME. This study also provides a starting point for researchers to better understand how effective safety leadership is provided by supervisors in terms of improving worker safety and safety knowledge-attitude-behaviour.

The surface chemistry and the morphology of SnO2 nanowires, deposited by Vapour Phase Deposition (VPD) method on Au-covered silicon substrate, were studied before and after subsequent air exposure. For this purpose, surface-sensitive methods including X-ray Photoelectron Spectroscopy (XPS), Thermal Desorption Spectroscopy (TDS) and the Scanning Electron Microscopy (SEM) were applied. The studies presented within this paper allowed to determine the surface non-stoichiometry combined with the presence of carbon contaminations, in a good correlation with the surface morphology. The relative concentrations of the main components [O]/[Sn]; [C]/[Sn]; [Au]/[Sn] together with the O – Sn; O – Si bondings were analyzed. The results of TDS remained in a good agreement with the observations from XPS. Moreover, conclusions obtained for SnO2 nanostructures deposited with the use of Au catalyst were compared to the previous obtained for Ag-assisted tin dioxide nanowires. The information obtained within this studies are of great importance for the potential application of SnO2 nanowires deposited on Au covered Si substrate in the field of novel chemical nanosensor devices, since the results can provide an interpretation of how aging effects influence gas sensor dynamic characteristics.

In recent years, ontology plays an important role in facilitating the semantic description of images which consists of describing the image by a set of words to describe the scene which signifies the belonging of the image. This description specified in several archaeological fields such as cultural, religious objects and heritage objects of France. However, the description of archaeological images is not yet exploited because this field is very diverse. In this article, we present a panel of ontology construction methods as well as archaeological ontologies. Also, we show our own OntunAr ontology to describe Tunisian archaeological images. In addition, we integrate OnTunAr into the automatic annotation of Tunisian archaeological images.

Many studies in the field of robot navigation have focused on environment representation and localization. The goal of map representation is to summarize spatial information in topological and geometrical abstracts. By providing strong priors, maps improve the performance and reliability of automated robots. Due to the transition to fully automated driving in recent years, there has been a constant effort to design methods and technologies to improve the precision of road participants and the environment's information. Among these efforts is the High Definition (HD) Map concept. Making HD maps requires accuracy, completeness, verifiability, and extensibility. Because of the complexity of HD mapping, it is currently expensive and difficult to implement, particularly in an urban environment. In an urban traffic system, the road model is at least a map with sets of roads, lanes, and lane markers. While more research is being dedicated to mapping and localization, a comprehensive review of the various types of map representation is still required. This paper presents a brief overview of map representation, followed by a detailed literature review of HD Map for automated vehicles. The current state of AV mapping is encouraging, the field has matured to a point where detailed maps of complex environments are built in real-time and have been proved useful. Many existing techniques are robust to noise and can cope with a large range of environments. Nevertheless, there are still open problems for future research. AV mapping will continue to be a highly active research area essential to the goal of achieving full autonomy.

Modern agent-based models (ABM) and other simulation models require evaluation and testing of many different parameters. Managing that testing for large scale parameter sweeps (grid searches) as well as storing simulation data requires multiple, potentially customizable steps that may vary across simulations. Furthermore, parameter testing, processing, and analysis are slowed if simulation and processing jobs cannot be shared across teammates or computational resources. While high-performance computing (HPC) has become increasingly available, models can often be tested faster through the use of multiple computers and HPC resources. To address these issues, we created the Distributed Automated Parameter Testing (DAPT) Python package. By hosting parameters in an online (and often free) "database", multiple individuals can run parameter sets simultaneously in a distributed fashion, enabling ad hoc crowdsourcing of computational power. Combining this with a flexible, scriptable tool set, teams can evaluate models and assess their underlying hypotheses quickly. Here we describe DAPT and provide an example demonstrating its use.

Since the 1970s, the application of microprocessor in industrial machinery and the development of computer systems have transformed the manufacturing landscape. The rapid integration and automation of production systems have outpaced the development of suitable human design criteria, creating a deepening gap where human factor was seen as an important source of errors and disruptions. Today the situation seems different: the scientific and public debate about the concept of Industry 4.0 has raised the awareness about the central role humans have to play in manufacturing systems, to the design of which they must be considered from the very beginning. The future of industrial systems, as represented by Industry 4.0, will rely on the convergence of several research fields such as Intelligent Manufacturing Systems (IMS), Cyber-Physical Systems (CPS), Internet of things (IoT), but also socio-technical fields such as social approaches within technical systems. This article deals with different Human dimensions associated with CPS and IoT and focuses on their conceptual evolution of automatization to improve the sociability of such automated production systems and consequently puts again the human in the loop. Hereby, our aim is to take stock of current research trends, and to show the importance of integrating human operators as a part of a socio-technical system based autonomous and intelligent products or resources. As results, different models of sociability as way to integrate human into the broad sense and/or the development of future automated production systems, were identified from the literature and analysed.

Accurate segmentation of the Left Ventricle (LV) in Echocardiogram (Echo) images is essential for cardiovascular analysis. Conventional techniques are labor-intensive and exhibit inter-observer variability. Deep learning has emerged as a powerful tool for automated medical image segmentation, offering advantages in speed and potentially superior accuracy. This study explores the efficacy of employing the YOLO (You Only Look Once) segmentation model for automated LV segmentation in Echo images. YOLO, a cutting-edge object detection model, achieves exceptional speed-accuracy balance through its well-designed architecture. It utilizes efficient dilated convolutional layers and bottleneck blocks for feature extraction, while incorporating innovations like path aggregation and spatial attention mechanisms. These attributes make YOLO a compelling candidate for adaptation to LV segmentation in Echo images. We posit that by fine-tuning a pre-trained YOLO based model on a well-annotated Echo image dataset, we can leverage the model's strengths in real-time processing and precise object localization to achieve robust LV segmentation. The proposed approach entails fine-tuning a pre-trained YOLO model on a rigorously labeled Echo image dataset. Model performance has been evaluated using established metrics such as mean Average Precision (mAP) at an Intersection over Union (IoU) threshold of 50% (mAP50) with 98.31%and across a range of IoU thresholds from 50% to 95% (mAP50:95) with 75.27%. Successful implementation of YOLO for LV segmentation has the potential to significantly expedite and standardize Echo image analysis. This advancement could translate to improved clinical decision-making and enhanced patient care.

Air filtration mechanisms in the composite filter media used in practical applications are important and challenging to understand because the component fibers could have various size scales and morphologies. In this work, a three-dimensional digital model of nanofiber-based filter media was reconstructed for the first time based on the X-ray tomography data for the cellulose substrate and the Focused Ion Beam-Scanning Electron Microscope (FIB-SEM) image analysis for the several microns thick (3.82-7.90 μm) electrospun polyvinylidene fluoride (PVDF) nanofiber membrane. Besides the high-resolution model where the details of the fibrous structures were fully resolved, another low-resolution model with approximated unresolved structures was also established. Filtration simulations utilizing these models were conducted considering the drag force, Brownian diffusion and aerodynamic slip. The simulated filtration efficiencies agreed well with the experiments for particles of 70-400 nm, including the most penetrating particle size (MPPS, 100-200 nm). Moreover, the structure-resolved models had higher accuracy but higher computational costs, while the unresolved simulations saved much running time but over-predicted the filtration efficiency, especially for smaller particles (<100 nm). Our study presents a comprehensive strategy for investigating the composite filter media with multiscale complex structures using a combination of advanced characterization technologies and modular simulation models.

Visualising textual content could be helpful to professionals as well as amateurs across several fields. However, training a text-to-image generator in the mainstream domain requires large amounts of paired text-image and data, which is too expensive to collect since labeling millions of images and videos can be tiresome. GANs like StackGAN and StyleGAN can be considered as solutions to generate images from text. But the images generated may be of low accuracy and resolution, and the entire processing can be highly time-consuming. Moreover, image generation is a notion that is still being researched. Hence, the process of developing a Video Generation model necessitates substantial research. Despite the need for such a model, modern technology has lagged behind the solutions to this problem. This proposal suggests combining two methods, Text modification for Action Definition (TexAD) and SeQuential Image Generation for Video Synthesis (SQIGen). The proposed solution synthesises a sequence of images from textual information feeds and combines these images to create a video. TexAD uses Natural Language Processing and Deep Learning techniques to process, classify and modify text data. SQIGen is an extension of the VQGAN+CLIP neural network architecture that generates a sequence of images from the modified text data

Dysprosody is a commonly described feature of speech deterioration due to Parkinson’s disease. Descriptions of the tonal movements underlying dysprosody have been attempted but has not afforded automation. The current study assessed a fully automated acoustic analysis pipeline in terms of its ability to predict human raters’ perception of dysprosody in patients with Parkinson’s disease. Read speech samples of 68 speakers with PD (45 male and 23 female) aged 65.0±9.8 years were assessed by four human clinical experts in terms of dysprosody severity. The recordings were also submitted to a speech processing pipeline in which portions with speech were identified and provided with a parametrization of intonation. Five models were trained and tuned based on 75% of utterances and their perceptual evaluations in a 10-fold cross-validation procedure and evaluated in terms of their ability to predict the perceptual assessments of recordings not included in the training. The performances of models were compared to human raters’ agreement with the majority vote on a speech sample. The results showed that human raters’ assessments of dysprosody can be approximated by the automated procedure. Variability in pitch does not adequately describe the level of dysprosody due to Parkinson’s disease.

The systems for automated monitoring of a human’s personal carbon footprint and CO2-equivalent emissions at industrial enterprises were developed in the article. The personal carbon footprint monitoring system includes data collection subsystems based on energy consumption metering devices, data storage and transmission, and calculation subsystems. To measure the consumption of water, electricity, thermal energy, IoT control sensors were selected. The calculation of the individual carbon footprint of a person is proposed. The system for automated monitoring of the carbon footprint of an enterprise includes a subsystem of devices for monitoring the use of energy resources, a subsystem for data transmission, calculation and prompt display of the carbon footprint. Selected devices for monitoring the consumption of water, energy and heat resources with data transfer to the SCADA system. An algorithm for calculating the carbon footprint of an enterprise is proposed. Structural schemes for automated carbon footprint control have been developed.

The rapid growth of Artificial Intelligence (AI) has led to considerable progress in Automated Fact Verification (AFV). This process involves collecting evidence for a statement, assessing its relevance, and predicting its accuracy. Recently, research has begun to explore automatic explanations as an integral part of the accuracy analysis process. However, the explainability within AFV is lagging compared to the wider field of explainable AI (XAI), which aims at making AI decisions more transparent. This study looks at the notion of explainability as a topic in the field of XAI, with a focus on how it applies to the specific task of Automatic Fact Verification. It examines the explainability of AFV, taking into account architectural, methodological, and dataset-related elements, with the aim of making AI more comprehensible and acceptable to the general society. Although there is a general consensus on the need for AI systems to be explainable, there a dearth of systems and processes to achieve it. In this research, we investigate the concept of explainable AI in general and demonstrate its various aspects through the particular task of Automated Fact Verification. We explore topic of faithfulness in the context of local and global explainability and how these correspond with architectural, methodological and data-based ways of achieving it. We examine these concepts for the specific case of AFV and analyze the current datasets used for AFV and how they can be adapted to further the identified aims on XAI. The paper concludes by highlighting the gaps and limitations in current data science practices and possible recommendations for modifications in architectural and data curation processes that would further the goals of XAI.

There is a strong need and demand from the United Nations, public institutions, and private sector for classifying government publications, policy briefs, academic literature, and corporate social responsibility reports according to their relevance to the Sustainable Development Goals (SDGs). It is well understood that the SDGs play a major role in the strategic objectives of various entities. However, linking projects and activities to the SDGs has not always been straightforward or possible with existing methodologies. Natural language processing (NLP) techniques offer a new avenue to identify linkages for SDGs from text data. This research examines various machine learning approaches optimized for NLP-based text classification tasks for their success in classifying reports according to their relevance to the SDGs. Extensive experiments have been performed with the recently released Open Source SDG (OSDG) Community Dataset, which contains texts with their related SDG label as validated by the community volunteers. Results demonstrate that especially RoBERTa achieves very high performance in the attempted task, which is promising for automated processing of large collections of sustainability reports for detection of relevance to SDGs.

Graphically-rich applications such as games are ubiquitous with attractive visual effects of Graphical User Interface (GUI) that offers a bridge between software applications and end-users. However, various types of graphical glitches may arise from such GUI complexity and have become one of the main component of software compatibility issues. Our study on bug reports from game development teams in NetEase Inc. indicates that graphical glitches frequently occur during the GUI rendering and severely degrade the quality of graphically-rich applications such as video games. Existing automated testing techniques for such applications focus mainly on generating various GUI test sequences and check whether the test sequences can cause crashes. These techniques require constant human attention to captures non-crashing bugs such as bugs causing graphical glitches. In this paper, we present the first step in automating the test oracle for detecting non-crashing bugs in graphically-rich applications. Specifically, we propose GLIB based on a code-based data augmentation technique to detect game GUI glitches. We perform an evaluation of GLIB on 20 real-world game apps (with bug reports available) and the result shows that GLIB can achieve 100\% precision and 99.5\% recall in detecting non-crashing bugs such as game GUI glitches. Practical application of GLIB on another 14 real-world games (without bug reports) further demonstrates that GLIB can effectively uncover GUI glitches, with 48 of 53 bugs reported by GLIB having been confirmed and fixed so far.

The world's growing population is highly dependent on animal agriculture. Animal products provide nutrient-packed meals that help to sustain individuals of all ages in communities across the globe. As the human demand for animal proteins grows, the agricultural industry must continue to advance its efficiency and quality of production. One of the most commonly farmed livestock is poultry and their significance is felt on a global scale. Current poultry farming practices result in the premature death and rejection of billions of chickens on an annual basis before they are processed for meat. This loss of life is concerning regarding animal welfare, agricultural efficiency, and economic impacts. The best way to prevent these losses is through the individualistic and/or group level assessment of animal on a continuous basis. On large-scale farms, such attention to detail was generally considered to be inaccurate and inefficient, but with the integration of Artificial Intelligence (AI) assisted technology individualized and per-herd assessments of livestock are possible and accurate. Various studies have shown cameras linked with specialized systems of AI can properly analyze flocks for health concerns, thus improving the survival rate and product quality of farmed poultry. Building on the recent advancements, this review explores the aspects of AI in the detection, counting and tracking of the poultry in commercial and research-based applications.

The quantitative and qualitative assessment of gold grains from samples of glacial till is a well-established method for exploring gold deposits hidden under glaciated cover. This method, widely used by the industry and which produced numerous successes in locating gold deposits in glaciated terrain, is still based on artisanal gravity separation techniques and visual identification. However, being artisanal, it is limited by inconsistent recoveries and the difficulty to visually identify the predominantly occurring small gold grains. These limitations hinder its capability to deceipher subtle or complex signal. To improve detection limits through recovery of small gold grains, a new approach has recently been introduced in the industry (commercially referred as “ARTGold” procedure) using an optimized miniature sluice box coupled with an automated scanning electron microscopy routine. The capabilities of this improved method are highlighted by comparing till surveys conducted around the Borden gold deposit (Ontario, Canada) using the conventional and improved methods at both local and regional scales. Relative to the conventional approach, the improved method recovered almost one order of magnitude more gold grains from samples (regional and down-ice mineralization), dominantly in small size fractions. Increasing the counts in low-abundance regional samples enables better discrimination between background signals and significant dispersions. The method offers an alternative to improve characterization of gold dispersal in glaciated terrain and the related gold deposit footprints.

This study describes the development of an automated bag valve mask (BVM) compression system, which, during acute shortages and supply chain disruptions can serve as a temporary emergency ventilator. The resuscitation system is based on the Arduino controller with a real-time operating system installed on a largely RepRap 3-D printable parametric component-based structure. The cost of the system is under $170, which makes it affordable for replication by makers around the world. The device provides a controlled breathing mode with tidal volumes from 100 to 800 milliliters, breathing rates from 5 to 40 breaths/minute, and inspiratory-to-expiratory ratio from 1:1 to 1:4. The system is designed for reliability and scalability of measurement circuits through the use of the serial peripheral interface and has the ability to connect additional hardware due to the object-oriented algorithmic approach. Experimental results demonstrate repeatability and accuracy exceeding human capabilities in BVM-based manual ventilation. Future work is necessary to further develop and test the system to make it acceptable for deployment outside of emergencies in clinical environments, however, the nature of the design is such that desired features are relatively easy to add with the test using protocols and parametric design files provided.

Recent researches proved that the underbridge geometry can be reconstructed by mounting a 3D laser scanner on a motorized cart travelling on a walkway located under the bridge. The walkway is moved by a truck and the accuracy of the bridge model depends on the accuracy of the trajectory of the scanning head with respect to a fixed reference system. In this paper, we describe the metrological characterization of a method that uses non-contact systems to identify the relative motion of the cart with respect to the walkway; the orientation of the walkway with respect to the bridge is determined using inclinometers and optical rails, while the position of the truck with respect to the bridge is measured using a conventional odometer. The measurement uncertainty of the proposed system was initially evaluated by numerical simulations and successively verified by experiments in laboratory conditions. The complete system has then been tested in operative conditions; the validity of the proposed approach has been demonstrated by comparing the geometry of buildings reconstructed with the proposed system with the geometry obtained with a static scan. Results evidenced that the errors are approximately 6 mm.

1) Introduction: Brain parcellation is an important processing step in the analysis of structural brain MRI. Existing software implementations are optimized for fully developed adult brains, and provide inadequate results when applied to neonatal brain imaging. 2) Methods: We developed a semi-automated pipeline, NeBSS, for extracting 50 discrete brain structures from neonatal brain MRI, using an atlas registration method that leverages the existing ALBERT neonatal atlas 3) Results: We demonstrate a simple linear workflow for neonatal brain parcellation. NeBSS is robust to variation in imaging acquisition protocol and magnet field strength. 4) Conclusion: NeBSS is a robust pipeline capable of parcellating neonatal brain MRIs using a simple processing workflow. NeBSS fills a need in clinical translational research in neonatal imaging, where existing automated or semi-automated implementations are too rigid to be successfully applied to multi-center neuroprotection studies and clinically heterogeneous cohorts. The software is open source and freely available.

Laser marking on polymer composite surfaces can be difficult to contrast and cause readability problems for electronic decoding equipment on production lines due to poor interaction between the laser and the fibres used to reinforce these materials. This problem can be solved with the right choice of marking parameters, resulting in savings for companies by avoiding production problems such as rejection, scrap and customer complaints. The present work uses the PBT/glass fibre composite used in the manufacture of instrument panels for motorcycles. The tests were carried out with different laser marking parameters using a Nd: YAG laser. Subsequently, the laser-marked DMC codes were analysed using a Verifier to evaluate the quality according to the ISO/IEC 29158:2020 standard. A detailed analysis of these surfaces was also carried out to observe some physical and chemical changes using SEM microscopy and EDS spectroscopy. The optical analysis showed that the lower the radiation power and pulse frequency and the higher the marking speed, the weaker the laser marking and therefore the poorer the DMC code quality, which was confirmed by the SEM. EDS spectroscopy showed that the laser marking process did not affect the chemical changes on the sample surface.

As a result of rapid population growth, an exponentially growing human population, and industrial expansion, it has become increasingly difficult to manage municipal solid wastes throughout the world. Decentralized waste management systems have created difficult situations in developing countries such as Malaysia. Wastes generated in the country, due to various cultural, social, and religious activities, organic and contributing to environmental pollution (air, water, and soil) and human health troubles. A questionnaire survey was participated by 220 construction professionals in Malaysia using structured and semi-structured methods. The framework was assessed using A partial least square structural equation modeling (PLS-SEM) to target sustainable development goals (SDG). Statistical analysis results indicate a significant effect between SCW management, since(r(270)=.687, P&lt;0.001). Improving factors has strong relationship with SCW management, since(r(270)=.723, P&lt;0.001). The mediation results also suggested a significant indirect positive effect of improving factors drivers on SCW management through policy-related factors sinceβ=0.688, t=8.254, P&lt;0.001, 95% CI for β=0.536,0.866. Finally, policy-related factors construct has a strong relationship with SCWM) management, since(r(270)=.811, P&lt;0.001) With the R Square of 0.787 and 0.785. The developed framework can improve construction waste management in the construction industry and enhance construction waste management to achieve global sustainable development goals. The findings show that one of the most critical issues of enhancing profitability is using preventive policies to reduce construction waste. This study could guide construction industry stakeholders in identifying the different waste management features during a building project's construction and design stage

Lateral vehicle control is a high importance in automated vehicles as it directly influences the vehicle’s performance and safety during operation. The Linear Quadratic Regulator (LQR) controller stands out due to its high-performance characteristics and is used in the open source for self driving functions. However, a notable limitation of the current approach is the manual calibration of LQR controllers based on the experience and intuition of the designers, leading to empirical uncertainties. To address this issue and enhance the lateral control performance, this paper concentrates on refining the LQR by employing three optimization algorithms: Artificial Bee Colony Optimization (ABC), Genetic Algorithm (GA), and Particle Swarm Optimization (PSO). These algorithms aim to overcome the reliance on empirical methods and enable a data-driven approach to LQR calibration. By comparing the outcomes of these optimization algorithms to the manual LQR controller within an offline multibody simulation as testing platform, the study highlights the superiority of the best-performing optimization approach. Following this, the optimal algorithm is implemented on a real-time system for the full vehicle level, revealing the Model-in-the-Loop and the Hardware-in-the-Loop gap up to 78,89% with lateral velocity when we use Relative Error Criterion (REC) method to validate and 2.35m with lateral displacement when considering by maximum absolute value method.

Recent global trends related to the increasing use of e-commerce are becoming a challenge for courier transport especially in the last-mile process of delivering products to the final retail recipient. One of the delivery methods is the personal collection of the parcel in an automated post box, available 24/7 for the customer. This research aims to define the most important attributes of the courier services quality, including the delivery of parcels through automated sending and receiving parcel lockers, leveraging advanced technologies, data, and connectivity to enhance the quality of life, sustainability, and efficiency for city residents. The research was based on a preliminary selection of the most important features of parcel lockers’ service quality, which were extracted from the analysis of scientific literature and previous research. The analysis was carried out by conducting a survey among city parcel locker users that provided data coded according to the dimensions of the Kano model. This allowed to conclude that the location of parcel stations, ensuring improvements for the disabled, adjusting the size of the parcel to the size of the box, proper placement of the parcel in the box and a properly functioning dedicated application are the most important features in the process of automatic delivery of parcels to recipients in urban areas. This paper enriches the literature on customer service quality of self-service technologies for last-mile delivery with the use of automated parcel lockers.

To solve two key problems in the identification of people who are infected with COVID-19: the first problem is that the identification accuracy is not high enough. The second problem is that present identification method such as nucleic acid testing is expensive in many countries. Methods: So, I decided to design a fast identification method for COVID-19 patients which is based on deep learning. After the model (CoughNet) learns more than 6,000 cough spectrograms of both COVID-19 patients and normal people, the accuracy rate of identification of COVID-19 patients and normal people is higher than 99% in the test set. Structure: This paper is mainly divided into three parts: the first part introduces the main background and research status of the research; The second part introduces the research methods; The third part introduces the specific process of the experiment.

Wearable technology will become available and allow prolonged electroencephalography (EEG) monitoring in the home environment of patients with epilepsy. Neurologists analyse the EEG visually and annotate all seizures, which patients often under report. Visual analysis of a 24 hour EEG recording typically takes one to two hours. Reliable automated seizure detection algorithms will be crucial to reduce this analysis. We study a dataset of behind-the-ear EEG measurements. Our first aim was to develop a methodology to reduce the EEG dataset by classifying part of the data automatically, while retaining 100% detection sensitivity (DS). Prediction confidences are determined by temperature scaling of the classification model outputs and trust scores. A DS of approximately 90% (99%) can be achieved when automatically classifying around 90% (60%) of the data. Perfect DS can be achieved when automatically classifying 50% of the data. Our second contribution demonstrates that a common modelling strategy, where predictions from several short EEG segments are used to obtain a final prediction, can be improved by filtering out untrustworthy segments with low trust scores. The false detection rate shows a relative decrease between 21% and 43%, and the DS shows a small increase or decrease.

Next-generation sequencing (NGS) has been a widely-used technology in biomedical research for understanding the role of molecular genetics of cells in health and disease. A variety of computational tools have been developed to analyse the vastly growing NGS data, which often require bioinformatics skills, tedious work and significant amount of time. To facilitate data processing steps minding the gap between biologists and bioinformaticians, we developed CSI NGS Portal, an online platform which gathers established bioinformatics pipelines to provide fully automated NGS data analysis and sharing in a user-friendly website. The portal currently provides 16 standard pipelines for analysing data from DNA, RNA, smallRNA, ChIP, RIP, 4C, SHAPE, circRNA, eCLIP, Bisulfite and scRNA sequencing, and is flexible to expand with new pipelines. The users can upload raw data in fastq format and submit jobs in a few clicks, and the results will be self-accessible via the portal to view/download/share in real-time. The output can be readily used as the final report or as input for other tools depending on the pipeline. Overall, CSI NGS Portal helps researchers rapidly analyse their NGS data and share results with colleagues without the aid of a bioinformatician. The portal is freely available at: https://csibioinfo.nus.edu.sg/csingsportal

Accurate inundation maps for flooded wetlands and rivers are a critical resource for their management and conservation. In this paper we automate a method (thresholding of the short-wave infrared band) for classifying inundation, using Landsat imagery and Google Earth Engine. We demonstrate the method in the Okavango Delta, northern Botswana, a complex case study due to the spectral overlap between inundated areas covered with aquatic vegetation and dryland vegetation classes on satellite imagery. Inundation classifications in the Okavango Delta have predominately been implemented on broad spatial resolution images. We present the longest time series to date (1990-2019) of inundation maps at high spatial resolution (30m) for the Okavango Delta. We validated the maps using image-based and in situ data accuracy assessments, with accuracy ranging from 91.5 - 98.1%. Use of Landsat imagery resulted in consistently lower estimates of inundation extent than previous studies, likely due to the increased number of mixed pixels that occur when using broad spatial resolution imagery, which can lead to overestimations of the size of inundated areas. We provide the inundation maps and Google Earth Engine code for public use.

Τhe concept of remote insect surveillance at large spatial scales for a number of serious insect pests of agricultural and medical importance is introduced in a series of our papers. We augment typical, low-cost plastic traps for many insect pests with the necessary optoelectronic sensors to guard the entrance of the trap in order to detect, time-stamp, GPS tag, and –in relevant cases- identify the species of the incoming insect from their wingbeat. For every important crop pest there are monitoring protocols to be followed in order to decide when to initiate a treatment procedure before a serious infestation occurs. Monitoring protocols are mainly based on specifically designed insect traps. Traditional insect monitoring suffers in that the scope of such monitoring: is curtailed by its cost, requires intensive labor, is time consuming, an expert is often needed for sufficient accuracy and can sometimes raise safety issues for humans. These disadvantages reduce the extent to which manual insect monitoring is applied and therefore its accuracy, which finally results in significant crop loss due to damage caused by pests. With the term ‘surveillance’ we intend to push the monitoring idea to unprecedented levels of information extraction regarding the presence, time-stamping detection events, species identification and population density of targeted insect pests. Insect counts as well as environmental parameters that correlate with insect’s population development are wirelessly transmitted to the central monitoring agency in real time, are visualized and streamed to statistical methods to assist enforcement of security control to insect pests. In this work we emphasize on how the traps can be self-organized in networks that collectively report data at local, regional, country, continental, and global scales using the emerging technology of the Internet of Things (IoT). This research is necessarily interdisciplinary and falls at the intersection of entomology, optoelectronic engineering, data-science and crop science and encompasses the design and implementation of low-cost, low-power technology to help reduce the extent of quantitative and qualitative crop losses by many the most significant agricultural pests. We argue that smart traps communicating through IoT to report in real-time the level of the pest population from the field straight to a human controlled agency can, in the very near future, have a profound impact on the decision making process in crop protection and will be disruptive of existing manual practices. In the present study, three cases are investigated : monitoring Rhynchophorus ferrugineus (Olivier) (Coleoptera: Curculionidae) using a) Picusan and b) Lindgren trap, and c) monitoring various stored grain beetle pests using the pitfall trap.

Diagnosing melanocytic lesions is among the most challenging problems in the practice of pathology. The difficulty of physically masking melanin pigment and the similarity of its color to commonly used chromogens often complicate examination of the cytomorphology and immunohistochemical staining results for tumor cells. Melanin bleach can be very helpful for histopathological diagnosis of heavily pigmented melanocytic lesions. Although various depigmentation methods have been reported, no standardized methods have been developed. This study developed a fully automated platform that incorporates hydrogen peroxide-based melanin depigmentation in an automated immunohistochemical analysis. The utility of the method was tested in one cell block of malignant melanoma cells in pleural effusion, ten ocular melanoma tissue samples, and ten cutaneous melanoma tissue samples. Our results demonstrated that the proposed method, which can be performed in only 3 hours, effectively preserves cell cytomorphology and immunoreactivity. The method is particularly effective for removing melanin pigment to facilitate histopathological examination of cytomorphology and for obtaining an unmasked tissue section for immunohistochemical analysis.

Synthetic biology uses engineering principles to redesign organisms and construct biological systems with specific functions, which is an important way to develop drugs, vaccines, biofuels, etc. In the process of transforming synthetic organisms, researchers need to conduct large-scale experiments for a long time, and many of these processes are manual and repetitive tasks, which results in the problems such as low throughput, low efficiency, and slow iteration. In addition, there are many experimental instruments and equipments required in the synthetic biology experiment process. The communication protocols between different instruments and equipments are not uniform, which seriously restricts the automation upgrade process of synthetic biology. To solve these problems, this paper put forward an integration technology based on the Object Linking and Embedding for Process Control Unified Architecture (OPC UA) to realize the interconnection of the synthetic biology automated casting platform and related instruments needed in synthetic biology process. The stability of the system is further designed and improved by using the concept of Triple Modular Redundancy. This helps the development of an efficient, stable and scalable automated casting platform for synthetic biology, which greatly improves the efficiency of synthetic biology experiments.

Regular inspections during construction work verify that the work completed is consistent with the plans and specifications and ensure that it is within the planned time and budget. This requires frequent physical site observations to independently measure and verify the completion percentage of the construction progress performed over periods of time. The current computer vision-based (CV) techniques for the measurement of as-built elements, predominantly use 3D laser scanning or 3D Photogrammetry modelling to determine the geometrical properties of as-built elements on construction sites. Both techniques require data acquisition from several positions and angles to generate sufficient information about the element’s coordinates making the deployment of these techniques on dynamic construction project sites a challenging task. In this paper, we propose a pipeline for automating the measurement of as-built components using artificial intelligence (AI) and computer vision (CV) techniques. The pipeline requires a single image obtained with a stereo-camera system to measure the size of selected objects or as-built components. We demonstrate our approach by measuring the size of concrete walls and columns. The novelty of this work is attributed to the fully automated CV-based method for measuring any given element using a single image only. The proposed solution is suitable for use in measuring the sizes of as-built components of built assets. It has the potential to be further developed and integrated with BIM models for use on construction projects for progress monitoring.

This study aims to develop novel automated computer vision algorithms and systems for component replacement inspection for Printed Circuit Boards (PCBs). The proposed algorithms are able to identify locations as well as sizes of different components. They are object detection algorithms based on keypoints of the target components. The algorithms can be implemented as neural networks consisting of two portions: frontend networks and backend networks. The frontend networks are used for the feature extractions of input images. The backend networks are adopted for producing component inspection results. Each component class can has its own frontend and backend networks. In this way, the neural model for the component class can be effectively reused for different PCBs. To reduce the computation time for the inference of the networks, different component classes can share the same frontend networks. A two-stage training process is proposed for effectively exploring features of different components for accurate component inspection. The proposed algorithm has the advantages of the simplicity for training data collection, high accuracy for defect detection, and high reusability and flexibility for online inspection. The algorithm is an effective alternative for the automated inspection in smart factory with growing demand for product quality and diversification.

Nowadays, power sector is an area that gather great scientific interest, due to events such as the increase in electricity prices in the wholesale energy market and new investments due to technological development in various sectors. These new challenges have in turn created new needs, such as the accurate prediction of the electrical load of the end users. On the occasion of the new challenges, Artificial Neural Networks approaches have become increasingly popular due to their ability to adopt efficiently to time-series predictions. In this paper, it is presented the development of a model which, through an automated process, will provide an accurate prediction of electrical load for the island of Thira in Greece. Through an automated application, deep learning load forecasting models have been created, such as Multilayer Perceptron, Long Short-Term Memory (LSTM), Convolutional Neural Network One Dimensional (CNN-1D), CNN-LSTM, Temporal Convolutional Network (TCN) and a proposed hybrid model called Convolutional LSTM Encoder-Decoder. The results in terms of prediction accuracy show satisfactory performances for all models, with the proposed hybrid model achieving the best accuracy.

Many spatial decision support systems suffer from user adoption issues in practice due to lack of trust, technical expertise, and resources. Automated machine learning has recently allowed non-experts to explore and apply machine learning models in the industry without requiring abundant expert knowledge and resources. This paper reviews recent literature from 136 papers, and proposes a general framework for integrating spatial decision support systems with automated machine learning to lower major user adoption barriers. Challenges of data quality, model interpretability, and practical usefulness were discussed as general considerations for system implementation. Research opportunities related to spatially explicit models in AutoML, and resource-aware, collaborative/connected, and human-centered systems were also discussed to address these challenges. This paper argues that integrating spatial decision support systems with automated machine learning can not only encourage user adoption, but also mutually benefit research in both fields — bridging human-related and technical advancements for fostering future developments in spatial decision support systems and automated machine learning.

During the past few years many projects and initiatives were undertaken deploying and testing automated vehicles for public transportation and logistics. However in spite of their ambition, all of these deployments stayed on the level of elaborated experimentation deploying no more than 4 maximum 5 AVs in rather small sites (few Kms of roads) and never really reached the level of large scale “commercial” deployment of transport services. The reasons for this are many, but the most important being the lack of economically viability and commercially realistic models, the lack of scalability of the business and operating models, and the lack of inclusive citizen/user centric services required for the large end-user acceptation and adoption of the solutions. In this paper, based on the experience gained in the H2020 AVENUE project, we present the missing pieces of the puzzle, ad which will be addressed in the Horizon Europe project ULTIMO.

Automated machine learning (AutoML) has been heralded as the next wave in artificial intelligence with its promise to deliver high performance end-to-end machine learning pipelines with minimal effort from the user. However, despite AutoML showing great promise for computer vision tasks, to the best of our knowledge, no study has used AutoML for image-based plant phenotyping. To address this gap in knowledge, we examined the application of AutoML for image-based plant phenotyping using wheat lodging assessment with UAV imagery as an example. We compared the performance of an open-source AutoML framework, AutoKeras in image classification and regression tasks to transfer learning using modern convolutional neural network (CNN) architectures. For image classification which classified plot images as lodged or non-lodged, transfer learning with Xception and DenseNet-201 achieved best classification accuracy of 93.2%, whereas Autokeras had 92.4% accuracy. For image regression which predicted lodging scores from plot images, transfer learning with DenseNet-201 had the best performance (R2=0.8303, RMSE=9.55, MAE=7.03, MAPE=12.54%), followed closely by AutoKeras (R2=0.8273, RMSE=10.65, MAE=8.24, MAPE=13.87%). Interestingly, in both tasks, AutoKeras models had up to 40-fold faster inference times compared to the pretrained CNNs. The merits and drawbacks of AutoML compared to transfer learning for image-based plant phenotyping are discussed.

Malware analysis is fundamental for defending against prevalent cyber security threats, and requires a means to deploy and study behavioural software traits as more sophisticated malware is developed. Traditionally, virtual machines are used to provide an environment that is isolated from production systems so as to not cause any adverse impact on existing infrastructure. Malware developers are fully aware of this and so will often develop evasion techniques to avoid detection within sandbox environments. In this paper, we conduct an investigation of anti-evasion malware triggers for uncovering malware that may attempt to conceal itself when deployed in a traditional sandbox environment. To facilitate our investigation, we developed a tool called MORRIGU that couples together both automated and human-driven analysis for systematic testing of anti-evasion methods using dynamic sandbox reconfiguration techniques. This is further supported by visualisation methods for performing comparative analysis of system activity when malware is deployed under different sandbox configurations. Our study reveals a variety of anti-evasion traits that are shared amongst different malware families, such as sandbox `wear-and-tear', and Reverse Turing Tests (RTT), as well as more sophisticated malware samples that require multiple anti-evasion checks to be deployed. We also perform a comparative study using Cuckoo sandbox to demonstrate the limitations of adopting only automated analysis tools, to justify the exploratory analysis provided by MORRIGU. By adopting a clearer systematic process for uncovering anti-evasion malware triggers, as supported by tools like MORRIGU, this study helps to further the research of evasive malware analysis so that we can better defend against such future attacks.

In this work, an algorithm for the scheduling of household appliances to reduce the energy cost and the peak-power consumption is proposed. The system architecture of a home energy management system (HEMS) is presented to operate the appliances. The dynamics of thermal and non-thermal appliances is represented into state-space model to formulate the scheduling task into a mixed-integer-linear-programming (MILP) optimization problem. Model predictive control (MPC) strategy is used to operate the appliances in real-time. The HEMS schedules the appliances in a dynamic manner without any a priori knowledge of the load-consumption pattern. At the same time, HEMS responds to the real-time electricity market and the external environmental conditions (solar radiation, ambient temperature etc). Simulation results exhibit the benefits of proposed HEMS by showing the reduction of up to 47% in electricity cost and up to 48% in peak power consumption.

Remediation of IT issues encoded into domain-specific or user-defined alerts occurring in cloud environments and customer ecosystems in a vast majority of cases suffers from accurate recommendations which could be timely supplied for recovery of performance degradations. That, of course, is hard to realize through furnishing those abnormality definitions with an appropriate expert knowledge which varies from one environment to another. At the same time, in a large proportion of support cases, the reported problems under Global Support Services (GSS) or Site Reliability Engineering (SRE) treatment ultimately go down to the product teams making them waste costly development hours on investigating self-monitoring metrics of our solutions. Therefore, the mean-time-to-resolution (MTTR) rates of problems/alerts are significantly impacted from lack of a systematic approach towards adopting AI Ops. That would imply building, maintaining, and continuously improving/annotating a data store of insights that ML models are trained and generalized across the whole customer base and corporate cloud services. Our ongoing study is in line with such a vision and validates an approach that learns the alert resolution patterns in such a global setting and explains them using interpretable AI methodologies. The knowledge store of causative rules is then applied in predicting potential sources of the application degradation reflected in an active alert instance. In this communication, we share our experiences with a prototype solution and up to date analysis demonstrating how root conditions are discovered with a high accuracy for a specific type of problem. It is validated against the historical data of resolutions performed by heavy manual development efforts. We also offer a Dempster-Shafer theory-based rule verification framework for experts as a what-if analysis tool to test their hypotheses about underlying environment.

Abstract Purpose: To analyze the correspondence between refractive astigmatism and corneal astigmatism in pseudophakic eyes with non-toric intraocular lenses. Setting: Yeouido St. Mary hospital, Seoul, South Korea Design: Evaluation of a diagnostic test instrument. Methods: This retrospective study included 95 eyes of 95 patients. Corneal astigmatism was measured with an automated keratometer (RK-5, Canon) and Scheimpflug tomography (Pentacam HR, Oculus). Refractive astigmatism was compared to keratometric astigmatism (based on anterior corneal measurements only), Equivalent K Reading and total corneal astigmatism (both based on anterior and posterior corneal measurements). Vector analysis was carried out by Næser’s polar value method. The accuracy was defined as the average magnitude of the vectorial difference in astigmatism (DA). Each corneal measurement was optimized in retrospect by a multiple linear regression equation between refractive and corneal astigmatism. Results: Keratometric astigmatism overestimated with-the-rule (WTR) refractive astigmatism and underestimated against-the-rule (ATR) refractive astigmatism. Several measurements based on both corneal surfaces values did not show any statistically significant difference with respect to refractive astigmatism. The mean corneal astigmatism by total corneal refractive power (TCRP) at 4.0 mm (zone/pupil) produced the lowest mean arithmetic DA and the highest percentage of eyes with a DA ≤0.50 diopter. After optimization, the accuracies of automated KA and TCRP 4.0 mm (zone/pupil) were similar. Conclusions: Total corneal astigmatism measured by the Scheimpflug tomography at 4.0 mm zone centered on pupil, accurately reflects the refractive astigmatism in pseudophakic eyes. However, the accuracy of total corneal astigmatism is not different from automated KA after optimization.

The pervasiveness of cardiovascular disease and physician misdiagnosis creates the urgent need for artificial intelligence models to improve diagnosis accuracy. The first objective of this study was to train machine learning models on publicly available data sets containing simple medical information of patients to diagnose cardiovascular disease. The Multilayer Perceptron (MLP) assembled for this task performed optimally with an F1 score of 0.8968. This prompted the creation of an open-source, automated cardiovascular disease diagnosis tool, powered by the MLP. The second objective of this study was to employ a meta-learning methodology called Local Interpretable Model-Agnostic Explanations (LIME) to understand the impact of different features on the model's diagnosis in the form of marginal probabilities. K-Means Clustering was employed to segment the data into ten clusters, after which each data example was passed through LIME. The resulting histograms depict the complex relationship between feature, cluster, and impact on diagnosis. A series of P-values with contrasting orders of magnitude shows the nuances in the MLP's understanding of patients from different clusters. The results of meta-learning analysis reveal that the most important features for cardiovascular disease diagnosis are fasting blood sugar, type of chest pain, and slope of the ST segment on an electrocardiogram. Future experiments should replicate the novel methodology introduced in this study on data sets containing more specialized medical features in order to gain practical medical insights about different types of cardiovascular disease represented by each cluster. Finally, feature engineering pathways should be explored with consideration of these results to create versatile diagnosis models not only for cardiovascular disease, but adaptable to other diseases as well.

The increasingly used approach of combining different simulation software in testing of automated driving systems (ADS) increases the need for potential and convenient software designs. Recently developed co-simulation platforms (CSP) provide the possibility to cover the high demand on testing kilometers for ADS by combining vehicle simulation software (VSS) with traffic flow simulation software (TFSS) environments. The emphasis on the demand of testing kilometers is not enough to choose a suitable CSP. The complexity level of the used vehicle, object, sensors and environment models is essential for valid and representative simulation results. Choosing a suitable CSP raises the question of how the test procedures should be defined and constructed and what the relevant test scenarios are. Parameters of the ADS, the environments, objects, sensors in VSS as well as traffic parameters in TFSS can be used to define and generate test scenarios. In order to generate a large number of scenarios in a systematic and automated way, suitable and appropriate software designs are required. In this paper we present a software design for CSP based on the Model-View-Controller (MVC) design pattern and implementation of a complex CSP for virtual testing of ADS. Based on this design, an implementation of a CSP is presented using the VSS from IPG Automotive called CarMaker and the TFSS from PTV Group called Vissim. The results have shown that the presented CSP design and the implementation of the co-simulation can be used to generate relevant scenarios for testing of ADS.

Gesture recognition has always been a technique to decrease the distance between the physical and the digital world. In this work, we introduce an Arduino based vehicle system which no longer require manual controlling of the cars. The proposed work is achieved by utilizing the Arduino microcontroller, accelerometer, RF sender/receiver, and Bluetooth. Two main contributions are presented in this work. Firstly, we show that the car can be controlled with hand-gestures according to the movement and position of the hand. Secondly, the proposed car system is further extended to be controlled by an android based mobile application having different modes (e.g., touch buttons mode, voice recognition mode). In addition, an automatic obstacle detection system is introduced to improve the safety measurements to avoid any hazards. The proposed systems are designed at lab-scale prototype to experimentally validate the efficiency, accuracy, and affordability of the systems. We remark that the proposed systems can be implemented under real conditions at large-scale in the future that will be useful in automobiles and robotics applications.

An automated discharge imaging system (ADIS), a non-intrusive and safe approach, was developed for measuring river flows during flash flood events. ADIS consists of dual cameras to capture complete surface images in the near and far fields. Surface velocities are accurately measured using the Large Scale Particle Image Velocimetry (LSPIV) technique. The stream discharges are then obtained from the depth-averaged velocity (based upon an empirical velocity-index relationship) and cross-section area. The ADIS was deployed at the Yu-Feng gauging station in Shimen Reservoir upper catchment, northern Taiwan. For a rigorous validation, surface velocity measurements were conducted using ADIS/LSPIV and other instruments. In terms of the averaged surface velocity, all measured results were in good agreement with small differences, i.e., 0.004 to 0.39 m/s and 0.023 to 0.345 m/s when compared to those from acoustic Doppler current profiler (ADCP) and surface velocity radar (SVR), respectively. The ADIS/LSPIV was further applied to measure surface velocities and discharges during typhoon events (i.e., Chan-Hom, Soudelor, Goni, and Dujuan) in 2015. The measured water level and surface velocity both showed rapid increases due to flash floods. The estimated discharges from ADIS/LSPIV and ADCP were compared, presenting good consistency with correlation coefficient R = 0.996 and normalized root mean square error NRMSE = 7.96%. The results of sensitivity analysis indicate that components till (τ) and roll (θ) of the camera are most sensitive parameter to affect the surface velocity using ADIS/LSPIV. Overall, the ADIS based upon LSPIV technique effectively measures surface velocities for reliable estimations of river discharges during typhoon events.

This paper presents novel feature descriptors and classification algorithms for automated scoring of HER2 in Whole Slide Images (WSI) of breast cancer histology slides. Since a large amount of processing is involved in analyzing WSI images, the primary design goal has been to keep the computational complexity to the minimum possible level and to use simple, yet robust feature descriptors that can provide accurate classification of the slides. We propose two types of feature descriptors that encode important information about staining patterns and the percentage of staining present in ImmunoHistoChemistry (IHC) stained slides. The first descriptor is called a characteristic curve which is a smooth non-increasing curve that represents the variation of percentage of staining with saturation levels. The second new descriptor introduced in this paper is an LBP feature curve which is also a non-increasing smooth curve that represents the local texture of the staining patterns. Both descriptors show excellent interclass variance and intraclass correlation, and are suitable for the design of automatic HER2 classification algorithms. This paper gives the detailed theoretical aspects of the feature descriptors and also provides experimental results and comparative analysis.

Document deskewing is a fundamental problem in document image processing. While existing methods have limitations, such as Hough Line Transformation that can deskew images upside down, and Deep Learning models that require huge amounts of human labour and computational resources and still fail to deskew while taking care of orientation, OCR-based methods also struggle to read text when it is tilted. In this paper, we propose a novel, simple, cost-effective deep learning method for fixing the skew and orientation of documents. Our approach reduces the search space for the machine learning model to predict whether an image is upside down or not, avoiding the huge search space of predicting an angle between 0 and 360. We finetuned a MobileNetV2 model, which was pre-trained on imagenet, using only 200 images and achieve good results. This method is useful for automation-based tasks, such as data extraction using OCR technology, and can greatly reduce manual labour.

BACKGROUND: Scoliosis is a widespread musculoskeletal disorder of bending and twisting of spine. In this medical ailment, spine curves to the side and even in severe cases it can twist and can take several bends. For the diagnosis and treatment of scoliotic patients, the Cobb’s angle is a critical marker of the body’s curvature. OBJECTIVE: There are many researches that have been conducted to automate the manual measurement of the angle and every investigation has their own limita- tions. METHODS: This paper presents a method for precisely measuring the Cobb’s an- gle using deep learning based techniques. Mainly it comprises of feature enhance- ment of augmented dataset, a bespoke code for landmark estimation on the spine, segmentation model based on the U-Net architecture and a custom code for Cobb’s angle measurement. These measured angles are then compared to the given angles for the segmentation on biomedical (X-ray) images. RESULTS: The findings demonstrate that the proposed technique offers an auto- mated and impartial way for precisely measuring this angle with an overall accu- racy of 97% and Root Mean Square Error (RMSE) of 4.99, which can lower the variability, facilitate early detection, accurate diagnosis, and monitoring of scolio- sis progression. Additionally, it aids in the treatment planning and evaluating treat- ment outcomes. CONTRIBUTION: By leveraging the applications of Cobb’s angle measurement, healthcare professionals can enhance the quality of care and can improve long-term outcomes for individuals with scoliosis.

Driver’s distractions are more prone to occur with automated driving vehicles, which might turn into cancelling some of their advantages. Traffic reports, naturalistic observations and in-lab tests are carried out to determine the influence of driver’s distractions in car crashes and to develop technology to detect and prevent them from happening. One of the best strategies to cope with this problem is education. In this work we propose a simulation environment to design laboratory experiments to study driver’s distractions as well as simple games to train drivers to take over the control of the vehicle when required. The result framework enables drivers to experience driving highly automated cars in their neighborhoods or in places of their choice with different levels of events to check their ability in taking over the control when required.

This paper explores the application of machine learning techniques for automated object grasping. Current electronic prosthetics often require extensive training for users to gain fine motor control over the prosthetic fingers, hindering their usability and acceptance. To address this challenge, this paper proposes an automated method that leverages computer vision-based techniques and machine learning algorithms. In this study, three reinforcement learning algorithms, namely Soft Actor-Critic (SAC), Deep Q-Network (DQN), and Proximal Policy Optimization (PPO), are employed to train agents for automated grasping tasks. The results indicate that the SAC algorithm achieves the highest success rate of 99% among the three algorithms at just under 200,000 timesteps. This research also shows that object’s physical characteristics can affect the agent’s ability to learn an optimal policy. Moreover, the findings highlight the potential of the SAC algorithm in developing intelligent prosthetic hands with automatic object gripping capabilities.

As the demands in reliability and high-degree of automation in industrial applications are increasing exponentially, the current Industry 4.0 trend lies in migrating towards smarter technologies that increase flexibility and provide autonomous operation. To tackle this, manufacturers shifted towards Real-Time Ethernet communication which supports autonomous operation, faster sensor/actuator configuration and high degree of determinism. Nevertheless, the uninterrupted operating principle of legacy industrial systems as well as the system complexity and heterogeneity constitutes the transition to Real-Time Ethernet very challenging. This article proposes a novel method allowing to automate the generation of executable code for Real-Time Ethernet architectures based on high-level programming models. The method is based on a programming model and modular code artifacts for the hardware architecture, employing Real-Time Ethernet communication. Through an tool-supported algorithm the high-level model is linked to the architecture's communication primitives and interfaces. The tool-support reduces significantly the development and debugging effort for Real-Time Ethernet applications and increases the application reliability, since the generated code is based on verified programming models. Additionally, the tool creates dedicated files, which allow automated industrial network configuration without any human intervention. Finally, by embedding firewall policies into the code generation process, the method guarantees cyber-resilience for the Real-Time Ethernet architecture. We demonstrate the proposed method in Programmable Logic Controllers (PLCs) of a Public Power Corporation's Hydroelectric Power Plant, which control the temperature and rotor speed of a power generator. The results demonstrate the method's ability to generate rapidly trustworthy and fault-tolerant code for the autonomous plant operation. The hurdles in time and effort for developing, configuring and debugging Real-Time Ethernet applications can be minimized through a high-level programming model that allows automated generation of executable code that is reusable for similar applications. Such time and effort reduction may pave the way towards the Industry 4.0 area.

Large-scale land cover plays a crucial role in global resource monitoring and management, as well as research on sustainable development. However, the complexity of the mapping process, coupled with significant computational and data storage requirements, often leads to delays between data processing and product publication, creating challenges for dynamic monitoring of large-scale land cover. Therefore, improving the efficiency of each stage in large-scale land cover mapping and automating the mapping process is currently an urgent and critical issue that needs to be addressed. We propose a high-performance automated large-scale land cover mapping framework(HALF) that introduces high-performance computing technology to the field of land cover production. HALF optimizes key processes, such as automated sample point extraction, sample-remote sensing image matching, and large-scale classification result mosaic and update. We selected several 10°×10° regions globally and the research makes several significant contributions:(1)We design HALF for land cover mapping based on docker and CWL-Airflow, which solves the heterogeneity of models between complex processes in land cover mapping and simplifies the model deployment process. By introducing workflow organization, this method achieves a high degree of decoupling between the production models of each stage and the overall process, enhancing the scalability of the framework. (2)HALF propose an automatic sample points method that generates a large number of samples by overlaying and analyzing multiple prior products, thus saving the cost of manual sample selection. Using high-performance computing technology improved the computational efficiency of sample-image matching and feature extraction phase, with 10 times faster than traditional matching methods.(3)HALF propose a high-performance classification result mosaic method based on the idea of grid division. By quickly establishing the spatial relationship between the image and the product and performing parallel computing, the efficiency of the mosaicking in large areas is significantly improved. The average processing time for a single image is around 6.5 seconds.

The vastness of chemical-space constrains traditional drug-discovery methods to the organic laws that are guiding the chemistry involved in filtering through candidates. Leveraging computing with machine-learning to intelligently generate compounds that meet a wide range of objectives can bring significant gains in time and effort needed to filter through a broad range of candidates. This paper details how the use of Generative-Adversarial-Networks, novel machine learning techniques to format the training dataset and the use of quantum computing offer new ways to expedite drug-discovery.

Functional mobility assessments (i.e., Timed Up and Go) are commonly used clinical tools for mobility and fall risk screening in the aging population. In this work, we proposed a new Mixed Reality (MR)-based assessment that utilized a Microsoft HoloLens^TM headset to automatically lead and track the performance of functional mobility tests, and subsequently evaluated its validity in comparison with reference inertial sensors. Twenty-two healthy adults (10 older, 12 young) participated in this study. An automated functional mobility assessment app was developed based on the HoloLens platform. Mobility performance was recorded with the headset built-in sensor and validated with reference inertial sensor (Opal, APDM) taped on the headset and lower back. Results indicate vertical kinematic measures by HoloLens was in good agreement with the reference sensor (Normalized RMSE ~ 10%). Additionally, the HoloLens-based test completion time was in perfect agreement with clinical standard stopwatch measure. Overall, our preliminary investigation indicates that it is possible to use an MR headset to automatically guide users to complete common mobility tests with good measurement accuracy, thus it has great potential to provide objective and efficient sensor-based mobility assessment.

Measuring cell confluence in high-throughput screening of pharmaceutics, cell culture monitoring, cancer research, and industrial applications requires quantitative and standardizable measures to minimize subjective observations and increase throughput1-12 . Over the past half-century, non-invasive specialized programs have been created to quantitatively assess cell confluence, and some software tools exist to meet these needs1,4,5,6,7,8,9 . However, many of these tools are expensive, computationally-demanding, or inaccessible to non-experts1,6. With the assistance of generative artificial intelligence, we have developed the Confluence Analysis Program (CAP), a modern tool designed to be precise, interactive, and user-friendly. CAP is written entirely in Python and runs in any command-line interface (CLI), including Terminal (OS) and Command Prompt (Windows). In addition to fetching all necessary external libraries automatically and prompting drag-and-drop image retrieval, CAP features live visual comparison of cell mass identification to the original image assay. Our results demonstrate robust performance of CAP on fluorescent micrographs of varying confluences ranging from low to high. CAP is provided as a free resource, accessible in the Supplementary Materials.

Artificial intelligence methods, especially artificial neural networks (ANNs), have increasingly been utilized for the mathematical description of physical phenomena in (metallic) material processing. Traditional methods often fall short in explaining the complex, real-world data ob-served in production. While ANN models, typically functioning as "black boxes," improve pro-duction efficiency, a deeper understanding of the phenomena, akin to that provided by explicit mathematical formulas, could enhance this efficiency further. This article proposes a general framework that leverages (CAE) ANNs to explain predicted results alongside their graphical presentation, marking a significant improvement over previous approaches and those relied on expert assessments. Unlike existing Explainable AI (XAI) methods, the proposed framework mimics the standard scientific methodology, utilizing minimal parameters for the mathematical representation of physical phenomena and their derivatives. Additionally, it analyzes the relia-bility and accuracy of the predictions using well-known statistical metrics, transitioning from deterministic to probabilistic descriptions for better handling of real-world phenomena. The proposed approach addresses both aleatory and epistemic uncertainties inherent in the data. The concept is demonstrated through the hot extrusion of aluminum alloy 6082, where CAE ANN models and predicts key parameters, and ChatGPT explains the results, enabling researchers and/or engineers to better understand the phenomena and outcomes obtained by ANNs.

Background: The variability of the obtained results of manual tests assessing the angle of strabismus depends on the experience, skills, and training of the examiner. The authors hope that the new measuring device will provide a more sensitive and repeatable method for detecting small strabismus angles compared to the gold standard – PCT. The purpose of this article is to present an innovative strabismus angle demonstration device, called Strabiscan, to present automated measurements of eye deviation, and to compare the obtained results of these measurements to the traditional manual method. Methods: In patients with the manifest strabismic disease (n = 30) and a group of healthy subjects (n = 30), a detailed history was taken and routine ophthalmologic examinations were performed, including best-corrected distance visual acuity, assessment of refractive error using an autorefractometer after cycloplegia, biomicroscopic evaluation of the anterior segment of the eye, and evaluation of the eye fundus by indirect ophthalmoscopy. Subsequently, each patient and healthy subjects were subjected to a prismatic cover-uncover test using a manual method, and then the presence of strabismus was detected and its angle assessed using demonstration Strabiscan device. Results: In the control group, using the Strabiscan demonstration device, small-angle latent strabismus ≤3DP was diagnosed in 83% of patients, and >3DP in 13%. In contrast, using the prismatic cover-uncover test, latent strabismus ≤3DP was diagnosed in only 13% of patients, and latent strabismus with an angle >3DP in 13% of patients. No statistically significant differences were noted in the measurements of strabismus angles made by the different methods. Conclusions: The Strabiscan demonstration device allows quick and accurate assessment of the strabismus angle. Compared to the prismatic cover-uncover test, it has a higher sensitivity for detecting low-angle latent strabismus. Measurements with the Strabiscan do not require the presence of additional co-assistants for the test.

During geomagnetic storms, which are a result of solar wind interaction with the Earth’s magnetosphere, geomagnetically induced currents (GICs) begin to flow in the long-distance high-voltage power grids on the Earth’s surface. It causes a number of negative phenomena that affect the normal operation of the entire electric power system. To investigate the nature of the phenomenon and its possible effects on transformers, a GIC monitoring system was created in 2011, the devices of which were installed at five substations of the Kola-Karelian power transit in northwestern Russia. Over 12 years of operating the system a large amount of data has been accumulated, which cannot be analyzed manually within a reasonable amount of time. To analyze the constantly growing volume of recorded data effectively, a method for automatic classification of GIC in autotransformer neutral was proposed. The method is based on a continuous wavelet transform of the neutral current data combined with a convolutional neural network (CNN) to classify the obtained scalogram images. As the result of comparing four CNNs with different architectures, a model that showed excellent GIC classification performance on the validation set (100.00% accuracy and loss of 0.0115) was chosen.

Fractures of the talar neck and body are associated with spine fractures and scoliosis deformity, which affect cosmetic appearance and cause difficulty in ambulation. The implant design for talus surgery is thriving as a functional alternative in case of severe talar destruction, focusing on segmentation and reconstruction of the talus’s shape. However, manual segmentation of the talus is time-consuming and subjective. In this study we exploited the automatic segmentation framework to efficiently train a deep learning-based model to accurately segment the talus based on computed tomography imaging. We developed three model configurations with nnU-Net and investigated their Dice similarity coefficients (DSC) and 95% Hausdorff distances (HD95) for talus segmentation on a CT image dataset. The three configurations performed well (DSC > 0.95, HD95 < 0.6). When tested on the same samples, one of the configurations was more efficient while ensuring higher accuracy. We propose to focus on talus anatomic variations with increasing age based on this framework and apply it to clinical trials at the next stage.

One of the most common forms of dementia is Alzheimer’s disease (AD), which leads to progressive mental deterioration. Unfortunately, there is no definitive diagnosis and cure that can stop the condition progressing. The diagnosis is often performed based on the clinical history and neuropsychological data, including magnetic resonance imaging (MRI). Deep neural networks (DNN) algorithms are gaining popularity for medical diagnosis, and have been used widely for the analysis of MRI data. DNNs can extract hidden features from thousands of training images automatically. However, they cannot judge how confident they are about their predictions. To use DNNs in safety-critical applications such as medical diagnosis, uncertainty quantification of DNNs predictions is crucial. For this purpose, Monte Carlo dropout (MCD) has been widely used, however, it may lead to overconfident and miss calibrated results. This paper proposes a framework in which the MCD algorithm’s hyper-parameters are optimized during training using Bayesian optimization for the first time. The conducted optimization leads to assigning high predictive entropy to erroneous predictions and making it possible to recognize risky predictions. The proposed framework is used for AD diagnosis, which has not been done before. We compare our method with some existing methods in the literature based on different uncertainty quantification criteria. The results of comprehensive experiments on the Kaggle dataset using a deep model pre-trained on the ImageNet dataset show that the proposed algorithm can quantify uncertainty much better than the existing methods.

InSAR and associated analytic methods can measure surface deformation from low earth orbit with a claimed accuracy of centimeters to millimeters. The realized accuracy depends on the area being measured and on the choice of analytic method, suggesting one choose a method in response to the area being measured. Here we consider a specific fixed analytic method and compare the results it produces to measurements gathered from other means in a variety of settings. In particular we compare Sentinel-1 InSAR with GPS at the Kilauea volcano around the 2018 eruption, with GPS in the city of Arica, Chile, and with public survey data at a decommissioned tailings mine. In addition, we compare two independent Sentinel-1 InSAR analyses for a railway station in Oslo, Norway. Our goal is estimate the accuracy of a fully automated Sentinel-1 InSAR pipeline in various settings. Our conclusions are that centimeter level accuracy is a reasonable claim in many, but not all settings, and that accuracy is typically not lost by using an automated pipeline, instead of hand-selecting and tuning parameters.

The basal ganglia (BG) are a central component of the brain, crucial to the initiation, execution and learning of adaptive actions. The BG are the major site of the action of dopamine. An important aspect of the BG architecture is the existence of two paths, direct and indirect, having different projection targets and dopamine receptor expression. To understand the BG, dopamine, and related disorders, it is imperative to understand the two paths. The standard account used in neuroscience research for decades posits that the role of the direct path is to support movements, while that of the indirect path is to suppress unselected or completed movements. This account is contradicted by converging evidence. Here, we explain why the arguments supporting the standard account are flawed, and present a new account, in which the role of the indirect path is completely opposite: to support automated execution. During acute events, the direct path allows coarse responses. These are refined by competition, and the resulting focused response is executed and learned by the indirect path, assisted by cholinergic interneurons and the subthalamic nucleus (STN). The new account allows a novel understanding of the symptoms of Parkinson's disease, in particular tremor and rigidity, and of its treatment by STN deep brain stimulation.

Building information modeling (BIM) is the digital representation of physical and functional characteristics (such as geometry, spatial relationship, and geographic information) of a facility to support decisions during its life cycle. BIM has been extended beyond 3D geometrical representations in recent years, and now includes time as a fourth dimension and cost as a fifth dimension, as well as such other applications as virtual reality and augmented reality. The Internet of Things (IoT) has been increasingly applied in various products (smart homes, wearables) to enhance work productivity, living comfort, and entertainment. However, research addressing the integration of these two technologies (BIM and IoT) is still very limited, and has focused exclusively on the automatic transmission of sensor information to BIM models. This paper describes an attempt to represent and visualize sensor data in BIM with multiple perspectives in order to support complex decisions requiring interdisciplinary information. The study uses a university campus as an example and includes several scenarios, such as an auditorium with a dispersed audience and energy saving options for rooms with different functions (mechanical/electric equipment, classrooms, and laboratory). This paper also discusses the design of a common platform allowing communication among sensors with different protocols (Arduino, Raspberry Pi), the use of Dynamo to accept sensor data as input and automatically redraw visualized information in BIM, and how visualization may help in making energy-saving management decisions.