The load cell is an indispensable component of many engineering machinery and industrial automation for measuring and sensing force and torque. This paper describes the design and analysis of the strain gauge load cell, from the conceptional design stage to shape optimization (based on the finite element method (FEM) technique) and calibration, providing ample load capacity with low-cost material (aluminum 6061) and highly accurate force measurement. The amplifier circuit of the half Wheatstone bridge configuration with two strain gauges has been implemented experimentally with an actual load cell prototype. The calibration test was conducted to evaluate the load cell characteristics and derive the governing equation for sensing the unknown load depending on the measured output voltage. The measured sensitivity of the load cell is approximately 15 mV/N and 446.8 µV/V at a maximum applied load of 30 kg. The findings are supported by FEM results and experiments with an acceptable percentage of errors, which revealed an overall error of 6% in the worst situation. Therefore, the proposed load cell meets the design considerations for axial force measurement for the laboratory test bench, which has a light weight of 20 g and a maximum axial force capacity of 300 N with good sensor characteristics.

The paper presents an error model of a measurement chain containing link performing discrete wavelet transform algorithm which is most often the last stage of measurement signal processing. The goal is to determine the uncertainty budget of the input quantities of the wavelet transform algorithm. The error model takes into account parts of analog, analog-to-digital and digital processing, describing the properties of subsequent fragments of the chain using their transmittance and processing functions. The proposed model enables the description of both deterministic and non-deterministic properties of signal errors. The proposed model was validated using an example measurement chain created for this purpose.

During operation, the support bracket is the main part to withstand the axial loads of the pumped storage unit. Moreover, the effects of axial loads including the hydraulic thrust of runner flow and the weight of runner body may cause the support bracket deformation and fatigue damage. For the safe and stable operation, the simulation of the axial force and the structural analysis of the support bracket of a pumped storage unit was carried out in this paper. The CFD simulation result has revealed the variation rule of the axial force in different operating conditions. Using ANSYS Mechanical, the static stresses and deformation of support bracket with axial loads were calculated. The results release the location and variations of maximum stress and maximum deformation caused by the axial loads. By comparing the predicted maximum axial force with the admission force calculated by the structural analysis, it is found that the axial force of the researched machine is within the safe range. This study provides the reference for the safety and stable operation of the pumped storage unit.

Complex blade responses such as a rotating stall or simultaneous resonances are common in modern engines and their observation can be a challenge even for state-of-the-art tip-timing systems and trained operators. This paper analyses forced vibrations of axial compressor blades, measured during the bench tests of the SO-3 turbojet. In relation to earlier studies conducted in ITWL with a small number of sensors, a multichannel tip-timing system let us observe simultaneous responses or higher-order modes. To find possible symptoms of a failure, blade responses in a healthy and unhealthy engine configuration with an inlet blocker were studied. The used analysis methods covered all-blade spectrum and the circumferential fitting of blade deflections to the harmonic oscillator model. The proposed modal solver can track the vibration frequency and adjust the engine order on the fly. That way, synchronous and asynchronous vibrations are observed and analysed together with an extended variant of least squares. The proposed approach helps to avoid common mistakes and saves a lot of work related to configuring the conventional solver.

In the paper, a study of the performance of unmanned ground vehicle (UGV), establishes numerical simulation model of the chassis system by three-dimensional software and finite element analysis software. Based on the numerical modelling and analysis, the work focuses on study of the strength and stiffness of the vehicle's chassis and researched the distribution of stress and deformation under the extremal condition. The paper also presents an autopilot design with new cascade control system for an autonomous motion of an unmanned ground vehicle based on Proportional-Integral-Derivative (PID) and Feed-Forward (FF) control. The PID-FF controller is a part of dedicated for presented UGV used in a hybrid control system for precise control and stabilization, necessary to increase the vehicle motion stability and maneuvers precision. The hybrid PID-FF control system proposed for the ground vehicle model gives a satisfactory quality of control, while maintaining the simplicity of the control system. Presented tests performed in area of mechanical design and control analysis gives good results and proves usefulness of designed unmanned device.

Long-span steel structure trusses are widely used in factory buildings, but with the growth of service time and the increase of dynamic load fatigue, a considerable part of the long-span truss with dynamic load appears serious transverse cracks at the bottom of the middle span and oblique deformation of the abdomen in the operation process. The U-shaped cracks at the bottom and belly, as well as the mid-span down deflection of the main truss, reduced the functional function of the factory building truss structure, and had to limit the original crane load, which affected the normal safety and durability of the structure. Therefore, the application principle of the variable axial force cable system in the long-span factory building truss structure and 3D3S software modeling [1] were used. Analyzing and studying the reinforcement method of large-span powerhouse truss can provide practical experience for subsequent similar projects. In view of the above phenomenon, the large-span powerhouse trusses of Hongcheng Powerhouse 1 and No.2 located in Tonglu, Zhejiang Province are used as the research object, and the variable axial force cable method is proposed to strengthen and lift the load. Considering the span of large-span powerhouse truss, the cable system with 22m controlling force of 400kN is proposed to be selected for powerhouse 1, and the cable system with variable axial force of 24m is proposed to be selected for Powerhouse 2. The force model of large-span truss is established by using the finite element method commonly used to analyze the force of truss. Under two working conditions, The influence of reinforcement effect is analyzed and compared from three aspects: stiffness, bearing capacity and stability. And the phenomenon of uneven stress distribution is analyzed. The stress distribution characteristics of each node are understood by simulating the most disadvantageous node plates with the greatest internal force before and after reinforcement.

In this paper, a new axial-type magnetic gear with auxiliary flux-enhancing structure (AFS-AMG) is proposed. Compared to conventional AFS-AMG, it has the higher torque density and higher permanent magnet (PM) utilization factor. Firstly, the design rules and operating principles of proposed AFS-AMG are elaborated. Then, the mapping relation between the radial-type magnetic gears (RMGs) and AMGs are elucidated. Compared to its counterpart in RMGs, AFS-AMGs achieve small size. Then, the geometrical parameters of AFS-AMGs are optimized to obtain the better electromagnetic performances, where the torque density per volume and per PM volume is adopted as the evaluation standard. Finally, three different AMG topologies are constructed in finite element analysis (FEA) software for comparison. It is proven that the AFS-AMG has the largest torque density per volume and per PM volume.

The paper presents section models for analysis of the resistance of RC members subjected to bending moment with or without axial force. To determine the section resistance the nonlinear stress-strain relationship for concrete in compression is assumed, taking into account the concrete softening. It adequately describes the behavior of RC members up to failure. For the reinforcing steel linear elastic-ideal plastic model is applied. For the ring cross-section subjected to bending with axial force the normalized resistances are derived in the analytical form by integrating the cross-sectional equilibrium equations. They are presented in the form of interaction diagrams and compared with the results obtained by testing conducted on RC columns under eccentric compression. Furthermore, the ultimate normalized bending moment has been derived for the rectangular cross-section subjected to bending without axial force. It was applied in the cross-sectional analysis of steel and concrete composite beams, named BH beams, consisting of the RC rectangular core placed inside a reversed TT welded profile. The comparisons made indicated good agreements between the proposed section models and experimental results.

In higher education, the cultivation of research competency is pivotal for students’ critical thinking development and their subsequent transition into the professional workforce. While statistics plays a fundamental role in supporting the completion of a research project, it is often perceived as challenging, particularly by students in majors outside mathematics or statistics. The connection between students’ statistical proficiency and their research competency remains unexplored despite its significance. To address this gap, we utilized the supervised machine learning approach to predict students’ research competency, as represented by their performance in a research methods class, with predictors of students’ proficiency in statistical topics. Predictors relating to students’ learning behavior in a statistics course such as assignment completion and academic dishonesty are also included as auxiliary variables. Results indicate that the three primary categories of statistical skills—namely, understanding of statistical concepts, proficiency in selecting appropriate statistical methods, and statistics interpretation skills— can be used to predict students’ research competency, as demonstrated by their final course scores and letter grades. This study advocates for strategic emphasis on the identified influential topics to enhance efficiency in developing students’ research competency. Findings could inform instructors in adopting a strategic approach to teaching the statistical component of research for enhanced efficiency.

This article is about a framework for determining the degree of realism of any given 1 passenger ride motion discomfort measurement formula. After providing some context and reviewing 2 evidence of deficiency in currently popular ride motion discomfort measurement formulas, the article 3 outlines the research program that needs to be carried out in order to establish such a framework. 4 The research begins with gathering recordings of uncomfortable ride motion episodes encountered in 5 a chosen type of passenger transport service. It then has test subjects compare the episodes via a ride 6 motion simulator and adjust their amplitudes pair wise until they cause equal discomfort. It explains 7 how to take the pair wise amplitude adjustments and determine amplitude adjustments that bring all 8 of the motion episode recordings to a common level of discomfort so that they form a normalized set. 9 Then, the lower the scatter of the scores assigned by any given discomfort measurement formula to 10 the members of that set, the more realistic that formula will be for the chosen service.

The majority of current methods for measuring the angular deflection of a laser beam enable measurement only in one selected plane. However, there are tasks in which measurements of laser beam deflections in 3D are required. In this paper, we present a way of enabling two-axial measurements of the deflection of a beam based on a single-axis sensor. The key idea is to direct a laser beam alternately into one of two arms of a measurement system. In the first arm, the beam is transmitted directly to the angular sensor, while in the second, the beam is directed to the sensor via a special optical element that rotates the plane of the beam deflection; in other words, this element changes the deflection in the horizontal plane into a deflection in the vertical plane, and vice versa. To alternate the path of the beam, a variable phase retarder and a polarising beamsplitter are used. The proposed technique is experimentally verified, and the results confirm its effectiveness.

The building envelope has the most significant contribution in the reduction of the building energy consumption. Application of new, alternative and improved materials and systems has an important impact on the buildings performances. This paper is focused on the thermal transmittance, as an indicator of the thermal conductance of the construction element. It includes comparisons of the U-values, calculated by software, with those measured in situ on three representative façade walls. The walls have been constructed with the new wall system Fragmat NZ-1, a new product in Macedonian buildings. This research provides basic information on the thermal transmittance of the system. The results of the analysis show that the in situ measuring is a useful tool in validation of the precision of analytically calculated values, since it was difficult to obtain precise results from the analytical calculations only, especially when the layers are with non-uniform thickness.

The up-to-date challenge towards clean road transport are non-exhaust emissions. Important advances regarding measurement systems, including well defined characterisation techniques, as well as regulation, will happen in the next few years. In this work we present detailed results of particle emissions from a test bed for wheel suspension and brakes, consisting of aerosol (size distribution, particle number (PN) and mass (PM)) and electron microscopy measurements (EM) under different load conditions. Standard tyres and brakes from series production were tested with a high-load driving cycle while particle measurements were conducted by gravimetric measurements and with a TSI SMPS, a TSI APS and a GRIMM OPS. Furthermore, samples were analyzed by electron microscopy. A bimodal particle size distribution (PSD) was obtained with the SMPS, with peaks at 20nm and around 400nm. EM analysis of >1400 single particles from the electrostatic sampler matches the PSD results. EM analysis also showed ultrafine particles, mainly from O, Fe, Si, Ba, Mg and S and also fractal particles with high C fractions. Our results suggest, in agreement with previously published literature, that particulate emissions are related to brake disc temperature and occur in significant amounts above a threshold temperature.

The paper presents the prediction of hydrodynamic characteristics of different rudder -plane configurations behind a submarine in deep water through the Reynolds-Averaged Navier-Stokes method in Ansys Fluent Solver. The hydrodynamic force and moment acting on the Cross-plane, X-plane, and Y-plane rudder configurations are analyzed for estimating hydrodynamic coefficientsfor predicting the advantages of each configuration to control the ship. The obtained results show that X-force of the X-plane rudder configuration is larger than the force acting on the Cross-plane rudder and Y-plane rudder configurations. However, Y-force, and Z-force of the X-plane rudder configuration are significantly greater than the Y-force of the left configurations. The same tendency can be seen in the moment of the X-plane rudder about the y-axis and z-axis. The roll moment induced by the Y-plane and Cross-plane rudder configurations is significantly larger than the case of the X-plane rudder configuration.

Dynamic time history analysis is a powerful and effective method to study the seismic response of tunnels, the dynamic time history to analyze the seismic response of the tunnel in the typical subway in this paper. The analysis results show that the overall levelling of the tunnel will not affect the tunnel too much, and the seismic response of the tunnel is mainly related to the relative displacement of the ground around the tunnel. The analysis results show that the internal force of the tunnel and the tunnel inclination have a good linear relationship, and the tunnel inclination can be used to measure the magnitude of the seismic response of the tunnel.

A problem of efficacy of crystal growth methods for crystallization from solution or melt has been investigated. Axial vibrational control (AVC) technique was considered as a perspective method to manage both heat-mass transfer and chemical component composition of the melts in the case of crystallization of complex chemical compounds. Numerical modeling and the search for generalized dependencies made it possible to predict the AVC parameters that provide optimal heat and mass transfer modes for creating flat liquid-solid interfaces, as well as the component composition of dissociated melts of various chemical compounds – Ge, NaNO3, CdTe.

Evidence of the efficacy and safety of colorectal stent placement for palliation remains insufficient. This single-arm, prospective, multicenter study with WallFlex enteral colonic stent included 200 consecutive patients with malignant large bowl obstruction in the palliation cohort. The technical and clinical success, as well as stent patency and complications as short-term (≤ 7 days) and long-term (> 7days) outcomes, of high axial force self-expandable metal stent (SEMS) placement was evaluated. The technical and clinical success rates were 98.5% and 94.5%, respectively. Non recurrent colorectal obstruction at 1 year was 63.9%, and 71.2% of the patients remained free of recurrent colorectal obstruction until death or the last follow-up. Fifty-six patients (28.0 %) received chemotherapy and five patients were administered bevacizumab after stent placement. The overall complication rate was 47%, including four (2.0%) early-onset and ten (5.0%) late-onset perforations, mostly due to stent-edge injury. Only the use of a long SEMS was a risk factor for perforation. In conclusion, endoscopic colorectal stenting using high axial force SEMS is an effective and safe procedure for palliation in patients with malignant colorectal obstruction. However, care should be taken to avoid perforation at the stent edge when using a long SEMS.

Abstract: Understanding the reliability and sensitivity of jump testing is essential to determine the neuromuscular progress of athletes and make informed decisions. This study aimed to assess the reliability and sensitivity of countermovement jump (CMJ) and drop jump (DJ) tests metrics in female volleyball players. Sixteen semi-professional female volleyball players participated in the study. Intrasession and intersession reliability of CMJ and DJ metrics were evaluated using a randomized cross-over design. Dual force platform was used to collect data, and several dependent variables were calculated using forward dynamics. Intraclass correlation coefficients (ICC), coefficients of variation (CV) and minimum difference (MD) were calculated. The third attempt presented the highest values for both test, and changes in jump strategy in DJ. CMJ is consistent across sessions, while DJ also shows intersession differences (p<0.05) in 11 out of 15 variables. Most CMJ variables exhibit excellent reliability while DJ variables have lower reliability and higher variability. Concentric and eccentric impulses for DJ showed excellent reliability. Most CMJ variables showed excellent reliability and variability, DJ had lower reliability, higher variability, and lower sensitivity. These findings provide valuable information when assessing athletes' performance and highlight the reliability, sensitivity, and variability in jump performance for CMJ and DJ tests.

The literature offers limited information on the effect of obesity on the rate of force development, a critical parameter for mobility in older adults. The objectives of this study were; to explore the influence of obesity on RFD in older adults and to examine the association between this neuromuscular parameter and walking speed. 42 older adults were classified into two groups: the control group (CG, n=22; age=81.13±4.02 years; Body mass index (BMI)=25.13±3.35 kg/m²), and the obese group (OG, n=20; age=77.71±2.95 years; BMI=34.46±3.25 kg/m²). Walking speed (m/s) was measured using the 10-meter walking test. Neuromuscular parameters of the plantar flexors were evaluated during a maximal voluntary contraction test using a dynamometer. The RFD was calculated from the linear slop of the force – time curve in two phases: from the onset of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200). The gait speed was lower in the OG compared to the CG (p

This paper proposed three-dimensional numerical simulation method by coupling of electrostatic and fluid fields to evaluating the performance of electrical sensor in the concentration measurement of gas/solid two-phase flow. Compared with the static numerical simulation, this real-time dynamic 3-D simulation method can research on a designed capacitance sensor combining the dynamic characteristics of the two-phase flows for concentration measurement. Several fluid-electrostatic models of transmission pipes with different sensor structures are built. Under different test positions and different particle concentrations, the flow characteristics and the corresponding electric signals can be obtained, and the correlation coefficient between the concentration values and the capacitance values are used for performance evaluation of the sensors. The effects of flow regimes on concentration measurement are also been investigated in this paper. To validate the results of simulation, an experimental platform with horizontal straight pipe for phase volume concentration measurement of solid/air two-phase flow is built, and the experimental results agree well with simulation conclusions. The simulation and test results show that the coupling models can give constructive reference opinions for the sensor design and collection of installation position in different transmission pipelines, which are very important for the practical process of pneumatic conveying system.

The scope of this study was twofold: first, to introduce a new method in examining measurement invariance, especially with large-scale studies where a large number of group comparisons are involved: the alignment approach, where only configural invariance is necessary to achieve measurement invariance. Second, to evaluate the psychometric robustness of this approach using real-life data. Particularly, we applied this approach to examine whether the factor structure of a cognitive ability test (PGAT) exhibits measurement invariance across the 26 universities of the Kingdom of Saudi Arabia. The sample consisted of 9,849 graduate students from 26 universities around the Kingdom. The results indicated a robust configural model suggesting that the P-GAT subscales were invariant across the 26 universities. Finally, the aligned factor mean values were estimated, and factor mean comparisons of every group’s mean with all other group means were conducted for both cognitive domains (Verbal and Quantitative). In both domains, King Saud University had the highest mean score among all universities. Moreover, its mean factor score was significantly higher than any other university besides Dammam University. On the other hand, several universities allocated at the northern and Southern borders of the country exhibited the lowest factor mean scores.

The electric field is enormously more powerful than the gravitational field. However, in our normal experience there is no electric field, the electric force is missing. How is it that when you get to larger and larger scales the gravitational field is extremely important whereas the electric field becomes less and less important [1]? This paper proposes a model to explain why gravitation dominates at a larger scale.

Objective: This study aimed to demonstrate the availability of portable devices for nasal FeNO measurement, which could replace exhaled NO measurement based on the continuous aspiration of multiple flow measurement systems. Methods: A descriptive cross-sectional study. The healthy subjects without rhinosinusis disorders (control group) and those with diagnosed allergic rhinitis (AR group) were enrolled in the study. They underwent nasal and bronchial FeNO measurements by both fixed flow NObreath® connected to nasal mask and multiple flows HypAir FeNO®. Results: A total of 153 people were recruited including 63 healthy subjects and 90 subjects with AR. There were no statistically significant differences in anthropometric characteristics between the two groups (P > 0.05). There were a significant increase in FeNO values in the AR group compared to the control group; concentrations of nasal and bronchial FeNO mearsured by NObreath® were 76.0 ± 50.7 ppb (vs 36.0 ± 28.1 ppb, P < 0.01) and 32.3 ± 15.4 ppb (vs 9.2 ± 5.6 ppb, P < 0.001), and those mearsured by NObreath® Hypair FeNO® were 1796.9 ± 523.3 ppb (vs 400.2 ± 123.1 ppb, P < 0.001) and 37.3 ± 23.0 ppb (vs 17.4 ± 18.3 ppb, P < 0.01). A weak correlation between the values measured by NObreath® and Hypair FeNO® devices was observed (r = 0.023 and r = 0.089, respectively; p < 0.05). Conclusions: The handheld NObreath® device is effective in measuring FeNO concentrations in both normal subjects and AR patients. The advantages in price and size, creating a compact, low-cost device that is convenient for use and research.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes. There are various types of canals, including calice, axial canals, and other internal canals, with structures that are dynamically altered during different coral growth states due to internal calcium transport. However, few studies have considered the regulation of calcium transport in Acropora. In this study, we investigated the morphological changes of the axial canal in six Acropora muricata samples by high resolution micro-computed tomography, observing the patterns of the axial canal during the processes of new branch formation and truncated branch rebuilding. We visualized the formation of a new branch from a calice and deposition of the iconic hexactin skeletons in the axial canal. Furthermore, the diameter and volume changes of the axial canal in truncated branches during rebuilding processes were calculated, revealing that the volume ratio of calcareous deposits in the axial canal exhibit significant increases within the first three weeks, returning to levels in the initial state in the following week. This work indicates that the axial canal can transport calcium to form hexactin skeletons in a new branch and rebuild the tip of a truncated branch. The calcium transport along canal network regulates various growth processes, including budding, branching, skeleton forming, and self-rebuilding of an Acropora colony. Understanding the changes in canal function under normal and extreme conditions will provide theoretical guidance for restoration and protection of coral reefs.

In thermal power plants equipped with air-cooled condensers, axial cooling fans operate under the influence of ambient flow fields. Under inlet cross-flow conditions, the resultant asymmetric flow field is known to introduce additional harmonic forces to the fan blades. This effect has previously been studied only numerically or using blade mounted strain gauges. For this study, Laser Scanning Vibrometry was used to assess fan blade vibration under inlet cross-flow conditions in an adapted fan test rig inside a wind tunnel test section. Two co-rotating laser beams scanned a low pressure axial fan, resulting in spectral, phase resolved surface vibration patterns of the fan blades. Two distinct operating points were examined, with and without inlet cross-flow influence. While almost identical fan vibration patterns were found for both reference operating points, overall blade vibration increased by 100% at low fan flow rate due to cross-flow, and by 20% at high fan flow rate. While numerically predicted natural frequency modes could be confirmed from experimental data as minor peaks in the vibration amplitude spectrum, they were not excited significantly by cross-flow. Instead, primarily higher rotation rate harmonics were amplified, i.a. a synchronous blade tip flapping was strongly excited at the blade pass frequency.

Although researchers have proposed various indentation size effect (ISE) models, these models often involve different form and number of parameters that can make our wonder which is the best in existed ISE models. Three types of ISE test data, namely, normal ISE, reverse ISE and transition of normal to reverse ISE, are used to evaluate the sixteen ISE models. The comparatively study indicates that H-J, N-G-Fs, N-G-H, N-G-A and N-G-Qs models can accurately predict the normal ISE. The reason for this is that the friction stress that is not related to dislocation activities or the indentation size effect of plastic zone has been introduced into these models. Therefore, these two factors should be considered in future ISE models. The sixteen ISE models are originally proposed to describe the normal ISE of different materials. However, to our surprise, some of these models are able to capture the reverse ISE and the transition of normal to reverse ISE of different materials. The determination coefficients (DC) of the sixteen ISE models are also determined for different materials. For reverse ISE, the highest DC value for NiCSi, TC4 and PED Ni are given by the EXP, N-G-Fs and N-G-A models, respectively. For the transition of normal to reverse ISE, the N-G-YC, N-G-Fs, and N-G-H models produce the maximum DC for ZrO2, Cu and Y2O3-ZrO2, respectively. Moreover, the mean DC of the N-G-Fs model is the maximum among the sixteen ISE models, followed by the N-G-H model, but they cannot accurately predict the reverse ISE. Therefore, the N-G-Fs and N-G-H models should be further modified to accurately predict the reverse ISE.

A space charge density wireless measurement system based on the idea of distributed measurement is proposed for collecting and monitoring the space charge density in an ultra-high-voltage direct-current (UHVDC) environment. The proposed system architecture is composed of a number of wireless nodes connected with space charge density sensors and a base station. The space charge density sensor based on atmospheric ion counter method is elaborated and developed, and the ARM microprocessor and Zigbee radio frequency module are applied. The wireless network communication quality and the relationship between energy consumption and transmission distance in the complicated electromagnetic environment is tested. Based on the experimental results, the proposed measurement system demonstrates that it can adapt to the complex electromagnetic environment under the UHVDC transmission lines and can accurately measure the space charge density.

We demonstrate for the first time efficient mechanical to electrical energy conversion using InGaN/GaN nanowires (NWs). Using an atomic force microscope equipped with a modified Resiscope module, we analyse the piezoelectric energy generation of GaN NWs and demonstrate an important enhancement when integrating in their volume a thick In-rich InGaN insertion. The piezoelectric response of InGaN/GaN NWs can be tuned as a function of the InGaN insertion thickness and position in the NW volume. The energy harvesting is favoured by the presence of a PtSi/GaN Schottky diode which allows to efficiently collect the piezo-charges generated by InGaN/GaN NWs. Average output voltages up to 330 ± 70 mV and a maximum value of 470 mV per NW has been measured for nanostructures integrating 70 nm-thick InGaN insertion capped with a thin GaN top layer. This latter value establishes an increase of about 35% of the piezo-conversion capacity in comparison with binary p-doped GaN NWs. By considering these output signals, we estimate a maximum power density generated by one layer of dense InGaN/GaN-based NW of about 3.3 W/cm². These results settle the new state-of-the-art for piezo-generation from GaN-based NWs and offer a promising perspective for extending the performances of the piezoelectric sources.

The group delay response of chirped fiber Bragg gratings (CFBG) written in polarization-maintaining fiber can be measured using the beat spectrum of the reflections from the two polarization axis, with a resolution and reproducibility better than 50 fs. The method is theoretically described, and we analyze the effect of group delay ripples (GDR) on the performance of a stretcher-compressor pair used in chirped pulse amplification systems. Ripples with a spectral period of the order of the pulse bandwidth are the most deleterious. Those are readily captured with our method, despite the limit on resolution due to the fiber polarization beat length. As a rule of thumb, the GDR should not exceed half the pulse duration. The reconstructed phase of the CFBG is also used to predict the pulse compression performance for a given device. Measurement of GDR as low as 161 fs is experimentally demonstrated.

The manual muscle test (MMT) is a flexible diagnostic tool, which is used in many disciplines, applied in several ways. The main problem is the subjectivity of the test. The MMT in the version of a “break test” depends on the tester’s force rise and the patient’s ability to resist the applied force. As a first step, the investigation of the reproducibility of the testers’ force profiles is required for valid application. The study examined the force profiles of n=29 testers (n=9 experiences (Exp), n=8 little experienced (LitExp), n =12 beginners (Beg)). The testers performed 10 MMTs according to the test of hip flexors, but against a fixed leg to exclude the patient’s reaction. A handheld device recorded the temporal course of the applied force. The results show significant differences between Exp and Beg concerning the starting force (padj=0.029), the ratio of starting to maximum force (padj=0.005) and the normalized mean Euclidean distances between the 10 trials (padj=0.015). The slope is significantly higher in Exp vs. LitExp (p=0.006) and Beg (p=0.005). The results also indicate that experienced testers show inter-tester differences and partly even a low intra-tester reproducibility. That highlights the necessity of an objective MMT-assessment. Furthermore, an agreement on a standardized force profile is required – a suggestion is given.

Along with the increasing industrialization of contries and population growth, the global. With the thougth of overcoming climate change and renducing greenhouse gas emissions in the atmosphere, interest in alternative sloar, wind, water, geothermal, tidal and ocean wave energy has significantly increased. Hydropower is one of the most used inexhaustible sources of energy on a global scale. The efficiency of water turbines can be increased by optimizing the blade cascade and the casing. For this purpose, research is conducted on specialized laboratory benches. The purpose is to determine the influencing parameters which affecting the nature of the power and cavitaion curves This paper presents the results of numerical and laboratoty studies of axial hydrokinetic turbines. A detailed analysis of the influence of the geometric parameters of the blades on the operating curves is made. A mathematica model for synthesis of the blade cascade is derived. An assessment of water energy soures has been made and sites of high energy potential have been pointed. The present material can be used for development of a methodology for calculation of efficient axial hydrokinetic turbines.

In the process of construction and operation of the pumping station, a large number of axial flow pumps pose a threat to the survival of fish in the natural environment. Through experiments, the survival conditions of many kinds of fish in extreme positive and negative pressure environment are explored, and -40 kPa is established as the low pressure damage threshold, which is used as a reference to analyze the probability of fish damage caused by pumps. The immersion boundary-lattice Boltzmann numerical method (LES-IB-LBM) based on large eddy simulation is used to optimize the parameters of the prototype runner of axial flow pump. A new type of runner with leading edge thickness of 11.4mm and blade cutting angle of 18 ° is optimized. This kind of runner has both hydraulic performance and fish-passing ability. The runner of the fish-friendly axial flow pump effectively guides the fish into the low risk area and reduces the risk of friction, shear and impact damage to the fish. the total impact mortality ratio of the runner of the axial flow pump before and after optimization is close to 7:1. The pressure damage analysis shows that the lowest negative pressure of the fish is -59.2 kPa, which is higher than -64.5 kPa of the prototype pump, and the highest positive pressure of the body surface is 11.8 kPa, which is lower than the 43.8 kPa of the prototype pump. Shear damage analysis shows that the fish will not be damaged by shear in the prototype pump and fish-friendly pump.

In Acropora, the complex canals in a coral colony connect all polyps into a holistic network to collaborate in performing biological processes, while axial canal is the largest canal amongst the network and distributes at the center of a coral branch. However, previous studies indicated that, in the non-radial symmetry transport system of Acropora, axial canal do not play a major role in the transport of hydroplasm, and the action of axial canal in coral growth is still obscure. In this study, we reconstructed six Acropora muricata samples by high resolution micro-computed tomography to investigate the growth patterns of axial canals during the processes of new branch forming and truncated branch rebuilding. We found that the axial canal of a new branch is transformed from a calice and the polyps in the new branch are budded from the polyp in the axial canal. Meanwhile, the axial canal can transport the calcareous skeletons to rebuild the tip of a truncated branch, which represents as the change in the diameter of axial canal and calcareous deposition/reduction in it. This work indicate the regulation of axial canal in the growth processes including budding, branching, and mineralising of an Acropora colony.

Tumor to stroma ratio is a highly debated prognostic factor in the management of several solid tumors and there is no universal agreement on its practicality. In our study we proposed to confirm or dismiss the hypothesis that a simple measurement of stroma quantity is an easy-to-use and strong prognostic tool. We have included 74 consecutive patients with colorectal cancer who underwent primary curative abdominal surgery. The tumors have been grouped into stroma-poor (stroma &lt;10%), medium-stroma (between 10 and 50%) and stroma-rich (over 50%). The proportion of tumor stroma ranged from 5% to 70% with a median of 25%. Very few, only 6.8% of patients had stroma-rich tumors, 4% stroma-poor tumors and 89.2%tumors with a medium quantity of stroma. The proportion of stroma, at any cut-off, had no statistically significant influence on the disease specific survival. This can be explained by the low proportion of stroma-rich tumors in our patient group and the inverse correlation of stroma proportion with tumor grade. The real-life proportion of stroma-rich tumors and the complex nature of the stroma-tumor interaction has to be further elucidated.

Axial spondyloarthritis (axSpA) is a chronic rheumatic disease characterised by the presence of inflammatory back pain. In patients with chronic low back pain, the lumbar flexion relaxation phenomenon measured by surface electromiography (sEMG) differs from that in healthy individuals. However, sEMG activity in axSpA patients has not been studied. The purpose of this study was to analyse the flexion relaxation phenomenon in axSpA patients. A study evaluating 39 axSpA patients and 35 healthy controls was conducted. sEMG activity at the erector spinae muscles was measured during lumbar full flexion movements. sEMG activity was compared between axSpA patients and the controls, as well as between active (BASDAI≥4) and non-active (BASDAI<4) patients. The reliability (using intraclass correlation coefficients (ICC)), criterion validity and discriminant validity using the area Under the curve (AUC) for the inverse flexion/relaxation ratio (1/FRR) were evaluated. Significant differences (p<0.05) were observed between axSpA patients and the control group in lumbar electric activity, especially during flexion, relaxation and extension and in FRR and 1/FRR (0.66±0.39 vs. 0.25±0.19, respectively). In addition, significant differences were found between active and non-active but also between non-active and healthy subjects. The sEMG showed good reliability (ICC>0.8 for 1/FRR) and criterion validity. ROC analysis showed good discriminant validity for axSpA patients (AUC=0.835) vs. the control group using 1/FRR. An abnormal flexion/relaxation phenomenon exists in axSpA patients compared with controls. sEMG could be an additional objective tool in the evaluation of patient function and disease activity status.

This paper presents a novel approach to power management techniques in energy storage system (ESS) interoperability with the energy power system (EPS) by inserting a SCADA controlled directional protection relay for improving the mode switching sequence. According with latest European standards, all necessary measures for re-synchronization and reconnection for health work of the system must be taken. The proposed approach intends to improve the “interface” between storage systems and electric power grid by using a directional relay which provides interoperability improvement by automatic recognizing and differentiating the switching sequence of the mode of operation from the fault mode. Simulated results from a small scale electrical generating system are provided. The results demonstrate that the proposed power management solution is technically ideal to achieve high quality energy while retaining the stability of the power grid network. The interoperability of PHS systems integrated with the electric power grid usually leads to perturbations in terms of frequency of the generated voltage, and for improving it we designed an automatic treating and re-connecting software module. This work regards the importance of producing electricity from green and renewable energy sources, while retaining the stability and reliability of the power grid. ESS systems are widely used to help balancing of intermittent forms of load demand on the electrical power grid at specific key moments. In this article, the pumped hydro storage (PHS) technologies are proposed as an economical way to utilize smoothly the off-peak energy or surplus energy, by pumping water to a reservoir at a higher level. During peak load periods, the stored water is discharged through the reversible pump-turbine to generate electricity to meet the peak demand controlled by designed SCADA application.

Energy Measurement and Verification (M&V) aims to make inferences about the savings achieved in energy projects, given the data and other information at hand. Traditionally, a frequentist approach has been used to quantify these savings and their associated uncertainties. We demonstrate that the Bayesian paradigm is an intuitive, coherent, and powerful alternative framework within which M&V can be done. Its advantages and limitations are discussed, and two examples from the industry-standard International Performance Measurement and Verification Protocol (IPMVP) are solved using the framework. Bayesian analysis is shown to describe the problem more thoroughly and yield richer information and uncertainty quantification than the standard methods while not sacrificing model simplicity. We also show that Bayesian methods can be more robust to outliers. Bayesian alternatives to standard M&V methods are listed, and examples from literature are cited.

Graph visualization has evolved significantly over time, offering various methods to effectively represent complex data structures. This study introduces a novel force-directed algorithm for 3D data visualization, specifically tailored for commonly used datasets in linked data visualization. Leveraging the power of graph theory and methods, the algorithm aims to address the challenge of creating visually appealing and easily interpretable visualizations, which often necessitate advanced user interaction. By utilizing 3D space and the Unity Engine, the research successfully visualizes data and develops interactive visualizations, overcoming limitations of basic force-directed implementations. The main contribution of presented research is in the force-directed algorithm with springs and controlled placement as a visualization technique that combines the use of springs and attractive forces to stabilize a graph in a 3D environment. The combination of these two techniques also helps prevent the formation of a single large cluster within the graph, enhancing the overall visualization quality.

The Universe is treated as an unbound thermodynamic system in which two forces of Nature compete: Attractive gravity loss and repulsive entropic gain. Entropic gain, although not presently considered a force of Nature, is otherwise well known and can be expressed with the gas laws. The Universe at the time of last scattering was all gas. Its instant gain is expressed as gas pressure. When the Gibbs equation is properly applied to this unbound gas, the resulting atomic Hubble parameter is found to be exclusively dependent on baryon density, giving a constant and perpetual two-to-one gain/loss ratio. Instant loss to gravity cannot offset gas pressure in this “thermal equation”. By contrast, the Friedmann equation, a ΛCDM foundation, treats baryon mass as accreted, having little if any entropic gain. These two equations are actually equivalent. Expanding accreted matter at its comoving critical density is herein shown to behave exactly like a freely expanding gas. However, neither equation includes all of today’s Universal kinetic energy, and cannot by themselves fully account for observed stellar movement. The present paper proposes the plausible existence of highly energetic or “suprathermal” free electrons which comprise about half of the intergalactic medium’s kinetic total. It is this suprathermal energy which Λ expresses. The fluid equation, another ΛCDM foundation, eliminates entropic gain from the Gibbs equation. Additionally, rest mass’s Einstein energy E=Mc² is treated as a thermal variable. These two assumptions, isoentropy and energy conflation, led astronomers to populate Λ as they followed the prior art.

This article deals primarily with the problem of determining the cutting force when machining hardened steels. Secondary issues are focused on the evaluation of surface quality on machined samples and the recommendation of cutting conditions. A wide variety of components are used in engineering, the final heat treatment of which is hardening. These components are usually critical in a particular product. The quality of these components determines the correct functioning of the entire technical equipment and ultimately its service life. In our case, these are the core parts of thrust bearings, specifically the rolling elements. The subject of the experiment is machining these components in the hardened state with cubic boron nitride tools and continuous measurement of the cutting force using a dynamometer. The following evaluation assesses the surface quality by both touch and non-touch methods. A structural equation with appropriate constant and exponents was then constructed from the data obtained using the dynamometer.

The availability of current land cover and land use (LCLU) information for monitoring the status of land resources has considerable value in ensuring sustainable land use planning. Similarly, the need to provide updated information on the extent of LCLU change in West Africa has become apparent, given the increasing demand for land resources driven by the rapid population growth in the sub-region. SERVIR West Africa, a regional consortium jointly supported by USAID and NASA to foster the use of geospatial and earth observation data and science for decision-making on critical environmental and food security challenges, in collaboration with the Food and Agriculture Organization of the United Nations (FAO), is building technical capacity in the sub-region to develop and implement harmonized regional land cover classification system for LULC change monitoring in West Africa, based on the Land Cover Meta Language (LCML-ISO 19144-2). This article focuses on the process, potential opportunities, outputs of this collaboration, exemplary use cases, and recommendations for the next steps.

The vertebrate anterior-posterior (A-P) body axis arises due to time space translation (TST). BMP dependent Hox temporal collinearity in early embryonic mesoderm generates the initial vertebrate axial pattern because the Hox codes associated with sequential times are frozen sequentially by BMP inhibiting signals from the embryonic organiser or node. There are three reasons why it is now opportune to review TST. 1/ It has become clear that this mechanism is highly relevant for current and emergent directions in medicine. Making a particular tailored stem cell or culturing a specific organoid in vitro both depend on it. 2/ This unexpected and perhaps unlikely sounding mechanism has recently been thoroughly validated. 8 recent primary publications from 6 major groups confirm that TST is the mechanism for primary axial patterning in the 4 best investigated vertebrate embryos. 3/ Its mechanism is now becoming clear. Previous publications propose it involves Hox regulation of cell movement during gastrulation or sequential stabilisation of Hox codes by anti BMP as above. Neither of these processes works alone but together they amount to a very convincing mechanism.

Most of the existing studies conducted on FRP-confined concrete considered circular and square concrete columns, while limited studies were on columns with rectangular sections. The studies have confirmed that the circular cross-sections exhibited higher confinement effectiveness, whereas in the case of non-circular cross-sections the efficiency of FRP confinement decreases with an increase of the sectional aspect ratio and there is no significant increase, particularly for columns with the aspect ratio of 2.0. As recently suggested by the researchers, to significantly increase the effectiveness of FRP-confinement for these columns is by modifying a rectangular section to an elliptical or oval section. According to the literature, most of the existing confinement models for FRP-confined concrete under axial compression have been proposed for columns with circular and rectangular cross-sections. However, modeling the axial strength and strain of concrete confined with FRP in elliptical cross-sections under compression is most limited. Therefore, this paper provides new expressions based on limited experimental data available in the literature. For a sufficient amount of FRP-confinement, the threshold value was proposed to be 0.02. Finally, the accuracy of the proposed model was verified by comparing its predictions with the same test database, together with those from the existing models.

In the case of solid slabs made of reinforced concrete that are usually subjected to bending, large areas of the structure are stressed well below their load-bearing capacity. Contrary to this are shell structures, which can bridge large spans with little material if designed according to the force flow. To improve the efficiency of ceiling slabs, we want to utilize the shell load-bearing behavior on a smaller scale by resolving the solid interior accordingly. In order to be able to study a wide range of such constructions virtually, a parametric multiobjective simulation environment is being developed in an ongoing research project. The basic analysis approaches which were implemented are presented in this paper. The basic workflow, the used programs and material models and their calibration on the tests on textile-reinforced concrete (TRC) samples are described.

The properties of the dark matter, dark energy, graviton and photon are discussed in terms of the new three-dimensional quantized space model. Three new particles (bastons) with the electric charges (EC) are proposed as the dark matters. It is proposed that the EC, LC and CC charges are aligned along the time axes but not along the space axes. The photon is confined on its corresponding three-dimensional quantized space. However, the graviton can be evaporated into other three-dimensional quantized spaces. The rest mass of the electron neutrino (n_e) of 3.494·10⁻³ eV/c² is obtained from the experimental vacuum energy density in terms of quantum field theory (QFT). The rest mass and force range of the massive g(0,0,0) graviton with the Planck size are m_g = 3.1872·10⁻³¹ eV/c² and x_r = 3.0955·10²³ m = 10.0 Mpc, respectively, based on the experimental rest mass and rms charge radius of the proton. The possible diameter (10 Mpc) of the largest galaxy cluster is remarkably consistent with the gravitational force range (10 Mpc). Then, the diameter of the largest dark matter distribution related to the largest galaxy cluster is 9.2865·10²³ m = 30 Mpc equal to the force range of the massive g(0) graviton with the rest mass of 1.0624·10⁻³¹ eV/c². Because of the huge number (N) of the evaporated gravitons, the very small Coulomb’s constant of about 10⁻⁴⁸k and large gravitation constant of 10⁶G_N are expected for the charged dark matters. Therefore, F_c(mm) > F_g(dd) > F_g(mm) > F_g(dm) > F_c(dd) > F_c(dm) = 0 for the proton-like particle. The proposed weak gravitational force between the dark matters and normal matters explains the observed dark matter distributions of the bullet cluster, Abell 1689 cluster and Abell 520 cluster. The transition from the galaxy without the dark matters to the galaxy with the dark matters are explained. Also, the accelerated space expansion is caused by the new space quanta created by the evaporated gravitons into the x1x2x3 space and repulsive electromagnetic force between dark matters corresponding to the dark energy. The decreasing coupling constant of the strong force, neutron lifetime anomaly and the pressure distribution inside the proton are explained by the unobservable proton and hadronization. And the rest mass of 1.4 TeV/c² is assigned to the Le particle with the EC charge of −2e. The proposed rest mass (26.12 eV/c²) of the B1 dark matter is indirectly confirmed from the supernova 1987A data. Also, the gravitation constant has been changing with the time because of the graviton evaporation.

Models of quantum measurements are presented, including observers subject to the laws of quantum mechanics. Observers perform multiple measurements in an attempt to disprove the collapse hypothesis. It is shown that under reasonable assumptions the effort cannot succeed. Under a unitary evolution the end state is a correlation between the result of the first measurement and the result(s) of the others, consistent with the observer's collapse hypothesis. The observer may conclude that the laws of nature include a non-unitary collapse mechanism, even if one does not actually exist. Discard of information is the crucial factor which distinguishes entanglement from measurement.

A variant of the von Neumann-Wigner Interpretation is proposed. It does not make use of the familiar language of wave functionsand observers. Instead it pictures the state of the physical world as a vector in a Fock space and, therefore not, literally, a functionof any spacetime coordinates. And, rather than segregating consciousness into individual points of view (each carrying with it asense of its proper time), this model proposes only unitary states of consciousness, Q(t), where t represents a fiducial time withrespect to which both the state of the physical world and the state of consciousness evolve. States in our world's Fock space areclassified as either 'admissible' (meaning they correspond to definite states of consciousness) or 'inadmissible' (meaning they donot). The evolution of the state vector of the world is such as to always keep it restricted to 'admissible' states. Consciousness istreated very much like what Chalmers calls an "M-Property." But we try to show that problems with the quantum Zeno effect do not arise from this model.

Force reduction is one of the most important benefit of applying ultrasonic vibration on milling. However, most of studies so far are limited to experimental investigation. In the current study, an analytical predictive model on cutting forces in ultrasonic vibration-assisted milling is proposed. The three types of tool-workpiece criteria are considered based on the instantaneous position and velocity of tool center. Type I criterion indicates that there is no contact if the instantaneous velocity is opposite to tool rotation direction. Type II criterion checks whether the vibration displacement is larger than the instantaneous uncut chip thickness. Type III criterion considers the overlaps between current and previous tool paths due to vibration. If none of these criteria is satisfied, milling forces are nonzero. Then the calculation is performed by transforming milling and tool geometry configuration to orthogonal cutting at each instant. The orthogonal cutting forces are predicted through the exhaustive search of shear angle and calculation of shear flow stress on tool-chip interface. The axial force is then calculated based on tool geometry, and the milling forces in feed, cutting, and axial directions are calculated after coordinate transformation. The proposed predictive force model in ultrasonic vibration-assisted milling is validated through comparison to experimental measurements on Aluminum alloy 2A12. The predicted values are able to match the measured milling forces with high accuracy of average difference of 13.6% in feed direction and 13.8% in cutting direction.

The seasonally adjusted civilian labor force participation rate, the sum of employed and unemployed persons as a percentage of the civilian non-institutional population, is analysed in the general to specific modelling framework with a saturating set of step indicators from January 1977 through June 2018. The results indicate that, ceteris paribus, the rise in the ratio of women to men in the labor force in addition to positive demographic movements can largely account for the rise in the labor force participation rate up to January 2000. Subsequently, the aging population helps to explain the decline. Recessions play a transitory role.

The vertebrate anterior-posterior (A-P = craniocaudal) axis is evidently made by a timing mechanism. Evidence has accumulated that tentatively identifies the A-P timer as being or involving Hox temporal collinearity. Here, I focus on the two current competing models based on this premise. Common features and points of dissent are examined and a common model is distilled from what remains. This is an attempt to make sense of the literature.

Knowing the mechanical properties of fibrous composite materials used in aeronautical industry from the design phase is a primary objective for designers. There are many methods for determining them, but they are laborious and require a long calculation time. And some of the methods are very approximate, giving only upper and lower bounds for these values. Experimental measurements also consume time and others resources. A method for sufficiently accurate and quickly obtained estimation of the engineering constants of the homogenized material is presented in the work. FEM is used to determine the natural frequencies of a standard bar, for which there are sufficiently precise classical methods for expressing these constants according to the properties of the homogenized material. In this way, these sought constants can be determined. In the work, Young's modulus will be determined for such a material, using the relationships that provide the proper pulsations for the longitudinal vibrations. Within the adopted model, transverse and torsional vibrations will be eliminated by blocking the nodes on the surface of the bars. In this way, more longitudinal self-pulsations can be obtained, so the precision in calculating the Young's modulus will increase.

The ratio between blade height and chord, named aspect ratio (AR), plays an important role in compressor aerodynamic design. Once selected, it influences stage performance, blade losses, and the stage stability margin. The choice of the design AR involves both aerodynamic and mechanical considerations, and a reasonable aim is frequently to achieve a desired operating range while maximizing efficiency. For a fixed set of aerodynamic and geometric parameters there will be an optimal choice in AR that achieves a maximum efficiency. However, for a state-of-the-art aero-engine design optimality means multi-objective optimality, that is reaching the highest possible efficiency for a number of operating points while achieving a sufficient stability margin. To this end, the influence of the AR on the performance of the first rotor row of a multistage multi-objective high-speed compressor design is analyzed. A careful setup of the high-speed aerodynamic design problem allows the effect of the AR to be isolated. Close to the optimal AR, only a modest efficiency variation is observed, but a considerable change in compressor stability margin (SM) is noted. Decreasing the AR allows for an increasing efficiency, but at the expense of a reduced surge margin. This allows the designer to trade efficiency for stability. Increasing the AR, however, is shown to reduce both surge margin and efficiency, hence a distinct optimality in stability is observed for the analyzed rotor blade row. In this work, the optimality in surge margin with respect to AR is observed whereas a close to optimal efficiency. The predicted range from AR=1.10 to AR=1.64, is only indicative, considering that the definition of a multi-objective optimality requires balancing efficiency and surge margin and that the choice of balancing these two criteria requires making a design choice along a pareto optimal front.

The kipping handstand push-up (kHSPU) is an exercise performed by many thousands of CrossFit participants. The safety of kHSPUs has been questioned because of vertical impacts upon the head. Here, we measured the axial loads placed upon the head during kHSPUs and sought to identify other factors that may place participants at risk of injury. 16 volunteers from a single gym performed 3 sets of up to 7 kHSPUs with their head and one hand contacting force platforms. Forces were recorded continuously and video recording were made while performing the exercises. The force profiles showed distinct landing and kipping peaks. Participants landed with more force than during their normal headstand, but less than their body weight. The force on the head was greatest during the "kip," and was usually more than body weight. Participants who reported pain following kHSPUs moved their head into extension during the exercises. Forces to the head during kHSPUs were below forces proposed for damage to the young male cervical spine, but overlapped those proposed for female cervical spines. While kipping handstand push-ups may be safe for young and previously uninjured male athletes, they may be unsafe for females and for those with previous injury or other compromising factors.

Weaving is an ancient and effective structural forming technique characterized by the ability to convert two-dimensional ribbons to three-dimensional structures. However, most 3D structures woven from straight ribbons have topological defects. Baek et al. proposed a method to weave smoother continuous 3D surface structures using naturally curved (in-plane) ribbons, obtained a new surface structure with relatively continuous variation of Gaussian curvature, and analyzed its geometric properties. We believe that this new 3D surface structure with smooth geometric properties must correspond to new mechanical properties. To this end, we investigated a 3D surface structure using naturally curved (in-plane) ribbon weaving, and the results of calculations and experiments show that such structures have better buckling stability than those woven with straight ribbons. It is observed that the number of ribbons influences the buckling behavior of different types of woven structures.

The paper contains the results of the 100-hour test campaign of the Additive Manufactured (AM) spare part (retainer – slipper) dedicated for an exact axial piston pump. The material of the retainer-slipper has been identified by using energy dispersive spectroscopy and replaced by other – with similar material properties as the original one. The obtained spare part had been subjected to only one postprocessing type (sandblasting) to analyze the influence of the rough part after the AM process. The whole test campaign has been divided into stages, where after each stage microscopic measurements have been made. During microscopical investigation roughness and geometrical measurements were conducted. The results revealed that it is possible to replace parts in hydraulic pumps with the use of AM. 100-hour test campaign caused about 500% increase in the surface roughness of the pump’s original part which was cooperated with the AM spare retainer-slipper, without any damages to the test system.

The Gurney flap (GF) is a miniature lift-enhancement device and is usually mounted at the trailing edge of an airfoil. The GF and has been successfully applied to isolated airfoils, multi-element airfoils, and aircraft wings as well as helicopter rotor due to its attractive features of simplicity, cost-effective and separation control. The GF also has aroused the attention of researchers in the turbomachinery industry. However, limited studies are currently available on the application of a GF to an axial fan.Hence, in this paper, we conduct a wind tunnel and computational fluid dynamic (CFD) investigation on an axial fan profiled with a NACA 65-(12)10 airfoil to evaluate the effect of the GF on the performance of the fan. We also present the detailed flow features of the fan with and without the GF after validating the simulation results with the experimental results. The experimental results show that as the GF is installed higher on the fan blade, it can produce a higher total pressure rise accompanied with a greater loss of efficiency. The installation of the GF also enlarges the work capacity of the fan. Detailed flow field analysis, including the surface pressure distribution, vorticity distribution at the trailing edge and streamline distribution of the fan, is carried out to understand the mechanisms of the effect of the GF on the performance of the fan.

A deep relationship is identified between the Coulomb Force and Gravity. A gravitational constant for strong gravity is calculated from the relationship. The equivalence between mass and charge is explored. Implications are given for the expansion of Einstein's Field Equations to include vector gravity.

Studies on evolution have made significant progress in multiple disciplines, but evolutionary theories remain scattered and controversial. Here we deduce that, thermodynamically, many carbon-based entities (CBEs) on the Earth tend to absorb energy from widespread relatively temperate heat streams on the Earth flowing from the solar, geothermal, and other energy sources, to form higher-hierarchy CBEs (HHCBEs). This has been the driving force of evolution leading to accumulation of HHCBEs for billions of years. We further deduce three progressive mechanisms of evolution including natural selection from the driving force. We hence establish the CBE evolutionary theory (CBEET) which reinterprets the major aspects of evolution in a comprehensive and comprehensible way. The CBEET provides novel explanations for natural selection, origin of life (abiogenesis), macroevolution, sympatric speciation, and evolutionary tempos. It suggests that evolution is driven hierarchy-wise by thermodynamics and favors fitness and diversity. It elucidates that altruism, collaboration, and obeying rules with balanced freedom are important throughout the CBE evolution which includes chemical evolution, biological evolution, and animal group evolution. The CBEET refutes several erroneous views including negative entropy and survival of the fittest. It integrates with research advances in multiple disciplines and links up laws of physics, evolution in biology, and harmonious development of human society.

Unpaid family caregivers must consider the economic trade-off between caregiving and paid employment. Prior literature has suggested labour force participation (LFP) to decline with caregiving intensity, but no study has evaluated this relationship by accounting for the presence of both kinks and discontinuities. Here we used respondents of the China Health and Retirement Longitudinal Study baseline survey who were non-farming, of working-age (aged 45-60) and had a young grandchild and/or a parent/parent-in-law. For women and men separately, a caregiving threshold-adjusted probit model was used to assess the association between LFP and weekly unpaid caregiving hours. Instrumental variables were used to rule out the endogeneity of caregiving hours. Of the 3,718 respondents in the analysis, for men, LFP was significantly and inversely associated with caregiving that involved neither discontinuities nor kinks. For women, a kink was identified at the caregiving threshold of 8 hours per week such that before 8 hours, each caregiving hour was associated with an increase of 0.0257 in the marginal probability of LFP, but each hour thereafter was associated with a reduction of 0.0014 in the marginal probability of LFP. These results have implications for interventions that simultaneously advance policies of health, social care and labour force.

The energy E takes the place of the gravitational mass m_G to produce gravity [1]. We wonder whether the inertial mass m_i in the inertial force is also replaced by E. The experiments to measure the inertial force and weight of a carrier are presented. Now we can test the principle of equivalence and study foundations of physics in condensed matter.

A recently developed thermodynamic theory for the determination of the driving force of crystallization and the crystal–melt surface tension is applied to the ice–water system employing the new Thermodynamic Equation of Seawater TEOS-10. The deviations of approximative formulations of the driving force and the surface tension from the exact reference properties are quantified, showing that the proposed simplifications are applicable for low to moderate undercooling and pressure differences to the respective equilibrium state of water. The TEOS-10 based predictions of the ice crystallization rate revealed pressure-induced deceleration of ice nucleation with an increasing pressure, and acceleration of ice nucleation by pressure decrease. This result is in, at least, qualitative agreement with laboratory experiments and computer simulations. Both the temperature and pressure dependencies of the ice–water surface tension were found to be in line with the le Chatelier–Braun principle, in that the surface tension decreases upon increasing degree of metastability of water (by decreasing temperature and pressure), which favors nucleation to move the system back to a stable state. The reason for this behavior is discussed. Finally, the Kauzmann temperature of the ice–water system was found to amount TK=116K, which is far below the temperature of homogeneous freezing. The Kauzmann pressure was found to amount pK=-212MPa, suggesting favor of homogeneous freezing upon exerting a negative pressure on the liquid. In terms of thermodynamic properties entering the theory, the reason for the negative Kauzmann pressure is the higher mass density of water in comparison to ice at the melting point.

Despite significant advances in metallurgy and the potential to create high and very high-strength steel, all international specifications for steel design provided little information about the limits of slenderness for high-strength steel sections (HSSs) and didn’t give anything about the design of very high-strength steel sections (VHSSs). The American structural steel design specification covers circular hollow sections (CHS) of steel grades up to S690, while it isn't in ANSI/AISC 360-16 and ASTM A514/A514M. Euro code EN 1993-1-1 can be applicable only to steel grades up to S460. EN 1993-1-3 and EN 1993-1-12 contain supplementary rules for cold-formed members and HSS (S460- S700), respectively. Though ductility requirements for (HSS) are specifically established in EN 1993-1-12, it is largely a continuation of the normal-strength-steel design procedures standardized in EN 1993-1-1, where (HSSs) are largely treated as normal-strength steels in these rules, and the same design approaches are used. The behavior of high and very high-strength steel circular hollow sections under axial compression load is studied in this research. A total of 16 nonlinear finite-element (FE) models were generated to replicate stub column tests that were experimentally tested by others in previous research. Hence, a parametric study is conducted using forty FE models developed to investigate the local buckling behavior under various slenderness ratios comprehensively. The developed models cover slenderness ratios ranging from 20 to 1226 and steel grades S460 and S1100 with yield stress equal 460 MPa and 1152 MPa, respectively. The FE results were combined with 105 previously collected experimental results to assess the applicability of existing codified design methodologies in the Euro code and the North American codes of cold-formed CHS. Based on the results of this study, new cross-sectional slenderness limits and new design equations for more efficient simple designs were presented for high and very-high strength steel circular hollow sections and Compared with the results of experimental tests and FE models.

This paper proposes a new structure of the dual-rotor hybrid-excited axial-flux permanent magnet vernier machine (DR-HEAFPMVM) with the modular stator and the consequent-pole PM (CPM) rotor for low-speed, high torque density applications such as in-wheel electric vehicles. The tooth-wound non-overlapping armature windings and direct current (DC) excitation windings are respectively arranged in stator main-teeth and split-teeth to obtain the modulated and adjustable air-gap flux densities, which result in the high torque density and outstanding flux-weakening capability. First, the design consideration, operation principle, and the air-gap flux density distributions of the proposed machine are elaborated based on the air-gap permeance function. Then, the influence of the pole ratios (PRs) and the DC excitation currents on the main electromagnetic performances of the DR-HEAFPMVM, such as the flux-weakening capability, back-electromotive force (back-EMF), on-load electromagnetic torque, loss distribution, and efficiencies, is investigated using the 3-D finite-element method (FEM). Results verify the feasibility of the flux adjustment of the DC excitation windings equipped in the split-tooth, and the design with a pole ratio of 8/1 tends to have higher torque density, higher machine efficiency, and considerable flux-weakening capability compared with the other two PRs.

Different values of the Hubble constant for extragalactic objects are not considered here. We give a number of examples of the extreme accordance of expansion rates of different fields of knowledge with the cosmological expansion rate. The coincidence of the expansion rates means that a common cause is almost inevitable. All these examples are gravitationally bound in themselves and in this case are subject to cosmological expansion. According to standard theory, this should not happen. We therefore question the common boundary of gravity and expansion for both theoretical and observational reasons and conclude that all gravitationally dominated objects participate in cosmological expansion or scale drift, contrary to general doctrine. The space expands with its contents while numerically maintaining distance, radius, rotation time and density. What is generally interpreted as an expansion is obviously a scale drift with a drift rate that corresponds to the size of the Hubble constant. The Earth is subject to expansion and scale drift. This results in numerically constant measured values. This drift apparently also applies to distant galaxies and other objects. The cosmological red shift is not interpreted here as a Doppler effect and numerical increase in distances, but in accordance with standard theory as an expansion or drift of the space-time scale. The expansion of the radii of galaxies makes the assumption of dark matter superfluous. The continents and our everyday environment are not subject to expansion or scale drift.

In this paper, a mathematical and physical interpretation of the length and the angle of the catenary curve made by the anchor chains was implemented, and the safety of an anchored vessel was reviewed. So far, holding force has been calculated approximately when the angle of the catenary curve of the anchor chain to the seafloor is 0°. In this study, the holding force equation was strictly derived for the case of anchor dragging. In addition, the equations for the angle and length of the catenary curve were mathematically derived when the anchor dragging occurs. The holding force equation derived in this paper are expected to help provide guidelines in vessel design or increase the safety of anchoring.

The pinning force density FpJc,B=Jc×B (where Jc is the critical current density and B is the applied magnetic field) is one of the main parameters that characterize the resilience of a superconductor to carry a dissipative-free transport current in an applied magnetic field. Kramer (1973 J. Appl. Phys. 44 1360), and Dew-Hughes (1974 Phil. Mag. 30 293) proposed a widely used scaling law for the pinning force density amplitude: FpB=Fp,max×p+qp+qppqq×BBc2p×1-BBc2q, where Fp,max, Bc2, p, and q are free-fitting parameters. Since the late 1970-s till now, several research groups have reported experimental data on the dependence of Fp,max on the average grain size, d, in Nb3Sn-based conductors. Godeke (2006 Supercond. Sci. Techn. 19 R68) proposed that the dependence obeys the law Fp,maxd=A×ln1d+B. However, this scaling law has several problems, for instance, the logarithm is taken from a non-dimensionless variable, and Fp,maxd&lt;0 for large grain sizes, and Fp,maxd→∞ for d→0. Here, we reanalysed the full inventory of publicly available Fp,maxd data for Nb3Sn conductors and found that the dependence can be described by Fp,maxd=Fp,max0×exp-dδ law, where the characteristic length, δ, varies within a remarkably narrow range, that is, δ=175±13 nm, for samples fabricated by different technologies. The interpretation of the result is based on the idea that the in-field supercurrent flows within a thin surface layer (thickness of δ) near the grain boundary surfaces (similar to London’s law, where the self-field supercurrent flows within a thin surface layer with a thickness of the London penetration depth, λ, and the surface is a superconductor-vacuum surface). An alternative interpretation is that δ represents the characteristic length of the exponential decay flux pinning potential from the dominant defects in Nb3Sn superconductors, which are grain boundaries.

Cell migration is essential for physiological, pathological and biomedical processes such as, in embryogenesis, wound healing, immune response, cancer metastasis, tumour invasion and inflammation. In light of this, quantifying mechanical properties during the process of cell migration is of great interest in experimental sciences, yet few theoretical approaches in this direction have been studied. In this work, we propose a theoretical and computational approach based on the optimal control of geometric partial differential equations to estimate cell membrane forces associated with cell polarisation during migration. Specifically, cell membrane forces are inferred or estimated by fitting a mathematical model to a sequence of images, allowing us to capture dynamics of the cell migration. Our approach offers a robust and potentially accurate framework to compute geometric mechanical membrane forces associated with cell polarisation during migration and also yields geometric information of independent interest, we illustrate one such example that involves quantifying cell proliferation levels which are associated with cell division, cell fusion or cell death.

This paper proposes a contact force controller for a constrained flexible manipulator in three-dimensional motion. This controller used the conversion formula obtained empirically and experimental results showed the effectiveness of the proposed contact force controller. First, the manipulator was operated with the tip of the second link restrained, then, time response of the root strain, joint angles and contact force were used to derive the relational between the three quantities. The effectiveness of the relational expression was verified by conducting a target contact force tracking experiment by inputting the angle from the relational expression. The contact force control using the strain feedback method was proposed with the strain amount estimated from the target contact force as the target value, and its effectiveness was verified by experiments. From the results obtained, controller using the strain feedback method was designed for the purpose of controlling the contact force at the tip of a flexible manipulator with two links and three degrees of freedom that performs three-dimensional spatial motion, and its effectiveness was shown by comparison with the contact force feedback method.

Background: The rate of force development (RFD) plays a pivotal role not only in preventing falls but also in ensuring successful completion of many functional tasks that demand swift muscle power rather than prolonged strength. Despite its importance, there is limited compre-hensive research on the relationship between RFD and walking speed, especially in older adults with Sarcopenic Obesity (SO). Objective: to investigate the influence of obesity on neuromuscular markers in older adults with SO and to assess the relationship between neuromuscular markers and gait speed in older adults with SO. Methods: a cohort of 42 participants was categorized based on their BMI into two groups: the sarcopenic non-obese group (CG, n=22; age=81.13±4.02; BMI=25.13±3.35) and the sarcopenic obese group (SOG, n=20; age=77.71±2.95; BMI=34.46±3.25). Gait speed was measured using a 10-meter test. Additionally, the isometric strength of the plantar flexor muscles was assessed during maximal voluntary contractions. Absolute Peak force (aPeak, N) were documented at intervals of 50 ms (a50, N), 100 ms (a100, N), and 200 ms (a200, N), subsequently normalized to body mass (r50, r100, r200, N). The RFD was derived in two phases: from the start of the contraction to 50 ms (RFD50-100) and from 100 to 200 ms (RFD100-200) and calculated from the linear slop of the force – time curve (Δ force/Δ time). Conclusion: Obesity negatively impacts neuromuscular markers in older adults. Notably, RFD emerges as the dominant factor influencing gait speed, accounting for an impressive 51% of its variability, far surpassing the impact of relative peak force. This underscores the imperative of evaluating neuromuscular health in older adults with SO to provide insights into mobility out-comes.

We investigated experimentally, analytically and numerically the formation process of double emulsion formations under dripping regime in a tri-axial co-flow capillary device. The results show that mismatches of core and shell droplets under a given flow condition can be captured both experimentally and numerically. We propose a semi-analytical model using the match ratio between the pinch-off length of the shell droplet and the product of the core growth rate and its pinch-off time. The mismatch issue can be avoided if the match ratio is lower than unity. We considered a model with the wall effect to predict the size of the matched double emulsion. The model shows slight deviations with experimental data if the Reynolds number of continuous phase is lower than 0.06, but asymptotically approaches to good agreement if the Reynolds number increases from 0.06 to 0.14. The numerical simulation generally agrees with the experiments under various flow conditions.

Abstract—The static and fatigue analysis of plates with holes, made of 2D woven roving composites, is conducted. The parametrization of convex holes is proposed. Experimental results of specimens without holes and with different shapes of notches are discussed. The fatigue behaviour is considered with the use of the low cycle fatigue method. The analysis is supplemented by the numerical finite element modeling. The present work is an extension of the results discussed in the literature. The finite element modeling of plates with holes is presented in details in Ref [1-3] including also the problems of the accuracy. The experimental results and the form of specimens are shown in Ref [4]. Two parametrical description of static and fatigue behaviour of plates with holes characterizes the goal and the novelty of the paper. The fuzzy approach is employed to reduce the number of experimental data [5].

On the basis of the force and safety factor analysis of traditional retaining wall, a new analytical method of force and displacement of slope is suggested, the numerical theoretical solution of the stress distribution of the sliding body can be obtained under the conditions, which the stresses distribution are satisfied with the differential equilibrium equations, the boundary conditions, the compatibility equation and the macroscopic equilibrium equations. The interface stresses between the sliding body and the retaining wall are continuous, the theoretical solution of retaining wall stress distributions can be gotten, while the stress differential equilibrium equation, the compatibility equation, macroscopic force and moment balance equations are satisfied. The strain and displacement solutions can be obtained by using Duncan Chang and Hooke constitutive equations for the slope and the retaining wall respectively. The transfer station of landfill in the Guandukou Town of Badong County is taken as an example, the results of the sliding body and retaining wall analysis show: The stress and strain solutions of a slope and a retaining wall can be obtained by the proposed method, the forces between the retaining wall and the sliding body include shear stress and normal stress, and the stress distributions change with the deformation of the sliding body, the shape and material of retaining wall can be optimized according to the calculation results，it is feasible for the proposed analysis method of slope with retaining wall design to be run many years.

This paper first explains the theory of the origin of force from a new perspective, explaining that the origin of all forces is caused by the "missing of energy in the time dimension" (non-conservation in a certain period of time), and constructs a unified theory of force on this basis. Then, through the unified theory of force, the following phenomena are reinterpreted: (1) The common origin of the inverse square law of gravitation and electromagnetic force; (2) The origin of the repulsive force of electrons and protons at small distances; (3) The mystery of the rotation curve of galaxies and the new explanation of "dark matter"; (4) explain the origin of the magnetic field; (5) Predict that moving magnets have the same radiation effect as charged particles (electron magnetic moments also have radiation effects); (6) Reinterpret Maxwell's displacement current; (7) Reinterpret synchrotron radiation and bremsstrahlung; (8) Explain that the strong and weak forces are short-range forces; (9) Predict the true structure of black holes and the origin of gravitational waves;(10) Possible explanation for the origin of the speed of light.

The present work studies the concept of productivity in shipbuilding and how it should be measured. The existing metrics, shipbuilding process and shipyard organization were studies in order to choose the most adequate metrics which would allow the measuring of a shipyard productivity in a systematic and holistic way. This is achieved by gathering the man-hours spent in each ship organized by cost centre and using Compensated Gross Tonnages as the measure of output from the shipyard. Data was gathered for thirty ships built in the same European yard organized by cost centre. From the data collected it was found that the ratio of hours spent in outfitting to the hours spent in structures is proportional to the complexity of the ship. There was also opportunity to study the work reduction resulting from building ships in series and the shares of labour for ships series and across ship types.

Qualitative and quantitative values estimation is a crucial aspect of social data science and plays a vital role in social and psychological research. Numerous methods of personal values measurement such as Schwartz Value Survey (SVS) and its re-modified versions have been proposed and invented, but many are challenged with one or more limitations. In this article, an alternative approach in a new paradigm of values measurement called Kabiru’s Value Survey (KVS) was proposed to measure the relative degree of importance or significance attached to particular value-actions of an individual(s) in a given population over a period. The methodological innovations in KVS unlike other existing methods of human value measurement include the use of habitually reported practices associated with a particular value-action in place of judging the series of Schwartz hypothetical statements, the use of multiple dependent variables rather than a single coded hypothetical statement. In terms of data analysis, a new approach of multivariate compression is introduced which merges the chain of multiple dependent variables into one coded scale. Psychometric result interpretation is also another innovative aspect of KVS methodology. Finally, the proposed methodology however solved some of the criticized limitations of the other methods of human value measurement.

Particle-mediated elasticity/viscoelasticity imaging has potential to expand the elasticity imaging field, as it can provide accurate and local tissue elastic properties as well as density, Poisson’s ratio, and viscosity. Here, we investigated elasticity imaging based on the use of small particles located within the tissue and at the tissue interface exposed to a static and dynamic external load. First, we discuss elasticity/viscoelasticity imaging methods based on the use of particles (bubbles and rigid spheres) located within the tissue. Elasticity/viscoelasticity imaging techniques based on the use of particles (bubbles, rigid and soft spheres) located at the tissue interface are then presented. Based on new advances, we updated some of the models for the responses of the particles located within the tissue and at the tissue interface available in the literature. Finally, we compared the mathematical models for the particles located within the tissue and at the tissue interface and evaluated the elasticity/viscoelasticity imaging methods based on the use of small particles. Therefore, instead of the use of the term elasticity imaging, we suggest the use of the term viscoelasticity imaging.

Starting with unitary quantum dynamics, we investigate how to add quantum measurements. Quantum measurements have four essential components: the furcation, the witness production, an alignment projection, and the actual choice decision. The first two components still lie in the domain of unitary quantum dynamics. The decoherence concept explains the third contribution. It can be based on the requirement that witnesses reaching the end of time on the wave function side and the conjugate one have to be identical. In this way, it also stays within the quantum dynamics domain. The surjection hypothesis explains the actual choice decision. It is based on a two boundary interpretation applied to the complete quantum universe. It offers a simple way to reduce these seemingly random projections to purely deterministic unitary quantum dynamics, eliminating the measurement problem.

In order to enhance the accuracy of the relative velocity measurement for the Mars explorer formation flight, we develop a relative velocity measurement method. In this method, the spectrometers at two Mars explorers are adopted to measure the starlight frequency shift and to estimate the velocity with respect to the star. Unfortunately, the instantaneous velocity of star can not be predicted accurately, which results in a large error in the velocity measurement. The difference of these two velocities, which does not include the proper motion of star, is the relative velocity between a pair of Mars explorers at the direction of the star. However, this navigation method can not work alone because of unobservability. To make the navigation system observable and improve the accuracy of both absolute and relative navigation for the Mars explorer formation flight, we combine it with X-ray pulsar navigation and the inter-satellite links, and propose an autonomous integrated navigation method with observability. In this integrated navigation scheme, the extended Kalman filter is adopted to deal with the relative velocity, the inter-satellite links and the pulse time-of-arrival, and estimate the absolute and relative navigation information for the Mars explorer formation flight. The simulation results demonstrate that both absolute and relative navigation accuracy of the proposed method are higher than that of the pulsar navigation, especially the relative one.

This paper describes the design and development of an active device that was applied to shoulder rotation rehabilitation. It implements a force control in a similar way to the haptic devices that reflect a force on the user’s hand according to the rehabilitation parameters. This device was tested with patients, combining clinician manipulation and programmed exercises. The results were excellent, given that the range of movement of the shoulder increased in most of the pa-tients. The results of the Usability Scale questionnaire were also promising.

The second law of thermodynamics states the increase of entropy, ΔS > 0, for real processes from state A to state B at constant energy from chemistry over biological life and engines to cosmic events. The connection of entropy to information, phase-space and heat is helpful, but does not immediately convince observers of the validity and basis of the second law. This gave grounds for finding a rigorous, but more easily acceptable reformulation. Here we show using statistical mechanics that this principle is equivalent to a force law ⟨⟨f⟩⟩> 0 in systems where mass centres and forces can be identified. The sign of this net force - the average mean force along a path from A to B - determines the direction of the process. The force law applies to a wide range of processes from machines to chemical reactions. The explanation of irreversibility by a driving force appears more plausible than the traditional formulation as it emphasizes the cause instead of the effect of motions.

This paper presents a numerical study on the vertical (axial) and lateral (flexure) behavior of CFST (Concrete-Filled Steel Tube) columns with active hoop prestress; this transverse prestressing effect is achieved by bolting together two steel half-tubes. This study refers to new construction only (i.e., no retrofit). 12 prototype CFST column specimens (segments) are analyzed. These specimens differ in the prestressing force (3 levels) and in the gravity loading ratio (4 levels); they are selected to represent typical ground columns of mid-rise buildings. The structural behavior of these column specimens is simulated with a nonlinear model implemented in Abaqus; the concrete and steel behavior are described with a damage-plasticity and a plasticity model, respectively. Finally, the interface concrete-steel interaction is represented by a hard (compression-only) surface-to-surface contact model. The calculations involve three consecutive loading steps: (i) transverse prestress, (ii) axial force, and (iii) lateral loading (shear force and bending moment). The structural behavior of the CFST columns is deeply examined and discussed; the results show that their axial-flexural capacity is adequate. Noticeably, it is concluded that the overall benefits of prestressing the columns are only modest. Preliminary studies on the aforementioned mid-rise buildings equipped with the CFST columns show that their gravity and wind capacities are largely enough; conversely, their seismic capacity is sufficient for moderate seismic ground motions only.

Expressions for the axial pressure profiles in a cylindrical channel and between parallel plates or a rectangular channel with large aspect ratio, with Maxwell slip gas flow are derived from first principles. The resulting expressions, which only involve the inlet and outlet pressures and the channel dimensions, will be useful in modelling or simulations of channel flows at Knudsen numbers in the range 0.001–0.1, such as in MEMS and NEMS. The expression for a cylindrical channel is validated by deriving from it an expression for the channel mass flow, which is shown to agree with a known expression for the mass flow through cylindrical channels with Maxwell slip flow. The expression for flow between parallel plates is found to agree with the zeroth order relation derived by Arkilic et al. using perturbation analysis. The effect of the accommodation coefficient on the pressure profile in a cylindrical channel is shown.

Through a modern derivation of Planck's formula for the entropy of an arbitrary beam of photons we derive a general expression for the entropy production due to the irreversible process of the absorption of an arbitrary incident photon spectrum in material and its dissipation into an infrared-shifted grey-body emitted spectrum, the rest being reflected or transmitted. Employing the framework of Classical Irreversible Thermodynamic theory, we define the generalized thermodynamic flow as the flow of photons from the incident beam into the material and the generalized thermodynamic force is then just the entropy production divided by the photon flow which is the entropy production per unit photon at a given wavelength. We compare the entropy production under sunlight of different inorganic and organic materials (water, desert, leaves and forests) and show that organic materials are the greater entropy producing materials. Intriguingly, plant and phytoplankton pigments (including chlorophyll) have peak absorption exactly where entropy production through photon dissipation is maximal for our solar spectrum $430<\lambda<550$ nm, while photosynthetic efficiency is maximal between 600 and 700 nm. These results suggest that the evolution of pigments, plants and ecosystems has been towards optimizing entropy production rather than photosynthesis. We propose using the wavelength dependence of global entropy production as a biosignature for discovering life on planets of other stars.

Objective: To explore the inter-rater reliability of the Measurement Of adherence Via Exercise Demonstration (MOVED) adherence tool. Design: Reliability study of a patient adherence measurement tool.Setting: Simulated physiotherapist-patient consultations. Participants: Sixteen experienced physiotherapists rated patient adherence to exercise. Interventions: N/A Main Outcome Measure: Inter-rater reliability of MOVED.Methods: The MOVED tool consists of two parts. Part one asks patients to self-report their adherence to exercise dose (including number of completed sessions, sets and repetitions in the last seven days). Part two asks patients to demonstrate each exercise. Component scores are totalled to give an overall level of patient adherence to each exercise.Participants were provided with a copy of five physiotherapist-prescribed exercises. Participants were then shown five corresponding video vignettes of simulated physiotherapist-patient consultations where patients were asked to self-report exercise frequency, sets and repetitions and demonstrate each exercise within the context of a consultation. Participants were asked to rate the level of patient adherence to each of the five exercises using the MOVED tool. Inter-rater reliability of MOVED scores was assessed using Intraclass Correlation Coefficient (ICC) and 95% Confidence Intervals. Results: The ICC of part one (self-report) was .90 (95%CI .74-.98), part two (demonstration) was .98 (95%CI .94-.99) and total score was .96 (95%CI .88-.99), demonstrating excellent inter-rater reliability. Conclusion: The MOVED tool, which can highlight whether patients are adhering to exercise technique as well as exercise dose, may provide clinicians and researchers with a more robust measure of exercise adherence when compared with other measures currently available.

Forensic anthropologists play a key role in skeletal trauma analysis and commonly use macroscopic features to distinguish between trauma types. However, this approach can be challenging, particularly in cases of highly comminuted or incompletely recovered fractures. Histological analysis of microscopic fracture characteristics in fractured bones may thus help provide additional information on trauma type and bone fracture biomechanics in general. This study analysed the extent of microcrack damage to osteons in long bones with blunt force trauma (BFT) and gunshot trauma (GST), from both traumatic death cases and post-mortem experimental fractures. We identified four types of osteonal damage (OD). In traumatic death cases, OD affecting the inside of the osteon and compromising the Haversian canal (type 1) was found to be indicative of BFT. Moreover, OD affecting the cement line (type 3) and interstitial lamellae (type 4) was more common in the GST samples. OD affecting the inside of the osteon without compromising the Haversian canal (type 2) was not found to be indicative of either trauma type. In cases of experimental fractures, our study revealed that post-mortem fractures in dry bone samples featured the highest amount of OD, particularly of type 4. This study also found that the experimentally produced GST featured similar OD pattern to GST death cases. These findings support our hypothesis that there are distinct osteonal damage patterns in human long bones with BFT and GST, which are of relevant value for trauma analysis in forensic anthropology.

The bipolar mitotic spindle drives accurate chromosome segregation by capturing the kinetochore and pulling each set of sister chromatids to the opposite poles. In this review, we describe recent findings on the multiple pathways leading to bipolar spindle formation in fission yeast and discuss these results from a broader perspective. Roles of four mitotic kinesins (Kinesin-5, Kinesin-6, Kinesin-12 and Kinesin-14) in spindle assembly are depicted, and how a group of microtubule-associated proteins, sister chromatid cohesion and the kinetochore collaborates with these motors is shown. We have paid special attention to the molecular pathways that render otherwise essential Kinesin-5 to become non-essential: how cells build bipolar mitotic spindles without the need for Kinesin-5 and where the alternate forces come from are considered. We highlight the force balance for bipolar spindle assembly and explain how outward and inward forces are generated by various ways, in which the proper fine-tuning of microtubule dynamics plays a crucial role. Overall, these new pathways have illuminated remarkable plasticity and adaptability of spindle mechanics. Kinesin molecules are regarded as prospective targets for cancer chemotherapy and many specific inhibitors have been developed. However, several hurdles have arisen against their clinical implementation. This review provides insight into possible strategies to overcome these challenges.

Two beneficial characteristics of aircraft generators are having armature windings and PM excitation sources placed on the stator side (maintenance and thermal management) and having a clear-cut rotor without permanent magnets or excitation windings (vulnerable at high speeds due to associated centripetal mechanical stresses). Within this framework, a doubly-salient permanent magnet (DSPM) generator was conceived by optimizing the stator size and rotor structure to minimize the torque ripple and maximize the RMS voltage value per turn of each generator phase. A Multi-Objective Design Strategy based on a 2D finite element analysis was used, being set to have characteristics closest to optimal for a Boeing 767 turbine, that is, the necessary electromotive force for a required power of 90 kW at 3000 rpm, feeding a simplified Boeing 767 electrical power distribution system. The results show that the machine could not deliver the required power at 3000 rpm since the 2D finite elements analysis demonstrates that the 2D model gives optimistic results when compared with the 3D FEM model. However, with a 3D finite element analysis of the machine feeding the aircraft load, it was seen that the machine’s efficiency is 92%, suggesting this machine can be a plausible solution.

One of the most popular techniques for determining electrical properties of material is the free-space measurement technique. With the potential for new applications requiring efficient, accurate and broadband material measurement systems using higher millimeter-wave and terahertz frequencies, the free-space measurement method has received renewed interest. This is mainly due to its simplicity, favorable properties as a non-destructive method, and it allows transmission and reflection measurements without any physical contact with the sample. This paper reviews and discusses state- of-the-art free space material measurement systems, starting with the different measurement techniques available for material characterization, their important concepts, post-processing in determining their properties, and progress towards expanding their use at higher frequencies. Also, this paper reviews dielectric material characterization using the free space method focusing on their application extension towards the higher frequencies. Besides, the algorithms for conversion methods and usage of lens in free space material measurement system was discussed in this paper. Finally, a future perspective on the outlook of this free space method is presented prior to the conclusion.

Acquisition of real-time hydraulic data is an essential component for flood forecasting. However, we frequently face difficulties in obtaining discharge data using classical contact methods during high magnitude floods and for systems experiencing rapid hydro-geomorphological adjustment. Therefore, we developed low-cost, non-contact sensors and platforms that are designed to overcome these difficulties. These advances enable flood flow properties to be monitored at multiple locations across a river catchment, at low-cost, and communicated in near real-time by using an image velocimetry method. This is an optics-based approach for stream flow measurement using commercially available near-infrared digital cameras to acquire video footage in full HD (30fps). Video footage is then subjected to optical flow tracking techniques based on cross-correlation, and feature-based tracking, enabling the displacement rates of detected features (for example natural foam, seeds, woody debris, and turbulent structures) to be computed. This manual provides step by step guidance to install an image-based gauging station. It contains the list of necessary components, the calibration process of a new camera and the assembly procedure of the system.

Self-report measurement is frequently used in human sports to assess training adaptations [1, 2]. This is a technique novel to the equestrian sport. The aim of this study was to describe how elite event riders of Germany evaluate their own fitness as well as that of their horses for the entire duration of an eventing season. Additionally, correlations with possible influencing external factors such as type of training or duration of grazing were also investigated. Short online questionnaires were used to allow eight riders to describe the training of their horses. Five criteria (general performance, ability to concentrate, general state of mind, general muscular condition and emotional wellbeing) were used to assess both, their horse's, as well as their own wellbeing. A 1-10 rating scale was used to score each criterion resulting in an average of 38 points out of 50 (maximum wellbeing) for horse (Std. dev. 0.55) and rider (Std. dev. 0.65) respectively. A total of 120 questionnaires were analysed. A correlation could be demonstrated (Spearman's correlation coefficient = 0.5) between rider and horse score, whereby it only became a linear correlation above 30 points. In addition, the horse score correlates positively with its success at competitions. While the horses were rated similarly throughout the season, the riders’ perceived welfare was higher in the middle of the season compared with the beginning and end of the season. Regularly turned-out horses resulted in higher horse scores (Linear mixed model, p=0,04, n=120). It can be concluded that the self-report measurement of fatigue and wellbeing can be a useful tool for trainers and riders to better determine the horse’s fatigue and recovery. It should be noted that external factors influence both, rider and horse assessment.

Strain-hardening cement-based composites (SHCC) are a novel class of fiber-reinforced concretes which exhibit high tensile strain capacity prior to failure localization. Although the tensile behavior of SHCC has been a matter of study in numerous research works, the behavior of these composites under other loading modes has scarcely been investigated. The article at hand addresses the mechanical behavior of two types of normal-strength SHCC subject to uniaxial tension, torsion, and combinations of torsional and axial loading. The SHCC under investigation were made with polyvinyl-alcohol (PVA) and ultra-high molecular weight polyethylene (UHMWPE) fibers, respectively. Digital Image Correlation (DIC) was applied to evaluate the multiple cracking process and crack opening modes in conjunction with the concretes’ axial and torsional loading histories. The study demonstrates the suitability of torsion experiments to assess the multi-axial and shear performance of SHCC, highlights the relation between multiple cracking and transfer capacity for shear forces, and emphasizes the importance of the type of reinforcing fibers on the shear strength and ductility of such composites.

Introduction and Problem: With conventional mechanical rotation measurement of joints, only static measurements are possible with the patient at rest. In the future, however, it would be interesting to carry out dynamic rotation measurements, for example when walking or doing sports. Therefore, a measurement method with an elastic capacitive measuring system was developed and validated. Material and Methods: The measurement system consists of a capacitive strain gauge connected to a flexible printed circuit board. The electronics on the printed circuit board are used for data acquisition and transmission. When the sensor strip is stretched, the distance between the fingers of the strain gauge changes and with it the capacitance. Consequently, the strain can be measured via the change in capacitance. The measurement system is taped to the knee with the sensor on the skin in the direction of the anterolateral ligament (ALL). The bottom of the sensor (silicone) and the bottom of the circuit board are in contact with the knee surface. The sensor must be attached to the knee without pre-stretching The system is validated with an in vivo test on 11 patients. For this purpose, the internal rotational laxity of the knee was tested on healthy volunteers and the results compared with the measurements on the static measuring device (Laxitester). The subjects are placed in the supine position. First the left and then the right leg is clinically examined one after the other and documented using an examination form. Exclusion criteria are the presence of a pathological ligament findings in the area of the collateral/cruciate ligaments, previous knee operations or limitations in the range of motion. The distal thigh rests on a support bench on which a knee joint flexion of 30° is set by height adjustment. The femoral condyles are secured against rotation in the positioning aid by posts. This also prevents internal rotation and displacement of the thigh. The foot is strapped into the holding device without shoes. The second toe beam is centered using an adjustable side clamp on the medial and lateral edge of the foot. Dorsiflexion is set at 2 Nm with a torque meter, in accordance with previous studies, to rule out rotational laxity in the ankle. The strain gauge sensor is taped to Gerdii’s tubercle in the course of the antero-lateral ligament below the lateral epicondyle of the thigh. Then, in three repeated measurements, the internal rotation of the foot and thus the lower leg is measured with a torque of 2 Nm. The change in length of the stretch mark is compared with the measured internal rotation angle in the static measuring device (Laxitester). Results: A significant difference between the sexes was found in the internal rotation range of the knee (p=0.003). The range of rotation was greater for female participants than for male participants. Regarding the measured length change values, the measurements presented showed an individual result for each participant, which tended to decrease with increasing internal rotation angle, with no age or gender differences being observed. The stiffness of the strain gauge was in the linear range for all measurements, within the first 20% strain of the sensor. The differences determined do not result from a different stretching of the sensor, but from individual differences between the test persons. The comparison between length change and internal rotation angle of the knee showed a strong positive correlation (r=1, p&lt;0.01). Conclusion: Elastic capacitive strain gauges can be used to reliably measure the internal rotation angle of the knee joint. This will allow dynamic measurements in the future.

Modern imaging strategies are paramount to studying living systems such as cells, bacteria, and fungi and their response to pathogens, toxicants, and nanomaterials as modulated by exposure and environmental factors. The need to understand the processes and mechanisms of damage, healing and cell survivability of living systems continues to motivate the development of alternative imaging strategies. Of particular interest is the use of label-free techniques that minimize interference of biological processes by foreign marking substances and reduce intense light exposure and potential photo-toxicity effects. This review focus on the potential synergic capabilities of atomic force microscopy (AFM) as a well-developed and robust imaging strategy with demonstrated applications to unravel intimate details in biomedical applications, with the label-free, fast, and enduring Holotomographic Microscopy (HT) strategy. We first review the operating principles that form the basis for the complementary details provided by these techniques regarding the surface and internal information provided by HT and AFM is essential and complimentary for the development of several biomedical areas studying the interaction mechanisms of nanomaterials with living organisms. First, AFM can provide superb resolution on surface morphology and biomechanical characterization. Second, the quantitative phase capabilities of HT enable superb modeling and quantification of the volume, surface area, protein content, and mass density of the main components of cells and microorganisms, including morphology of cells in microbiological systems. These capabilities result from directly quantifying refractive index changes without requiring fluorescent markers or chemicals. As such, HT is ideally suited for long-term monitoring of living organisms in conditions close to their natural settings. We present a case-based review of the principal uses of both techniques and their essential contributions to nanomedicine and nanotoxicology, emphasizing cancer and infectious disease control. The synergic impact of the sequential use of these complementary strategies provides a clear drive for adopting these techniques as interdependent fundamental tools.

The purpose of this study was to investigate the horizontal force and contribution of shoulder horizontal adductor and elbow extensor muscles activity during wide and narrow grip bench press (BP) in various conditions, such as resistance trained/non-trained, concentric/eccentric and muscle fatigue/non-fatigue.　We measured the horizontal force on the bar and the electromyographic (EMG) muscle activity of pectoralis major (PM) and triceps brachii (TB) during 10RM BP with wide grip (81cm) and narrow grip (40cm)　in 7　resistance trained men and 7 non-trained men. The all-reps average of the horizontal to vertical force ratio both in resistance trained and non-trained subjects was about 30% outward for the wide grip, and about 10% inward for the narrow grip. The EMG contribution ratio PM/TB shows no significant differences between narrow and wide grip in all evaluated conditions except in non-trained subjects muscle fatigue eccentric phase. Both resistance trained and non-trained subjects did not push the bar straight upward, and the EMG PM/TB was almost unchanged by hand width. The direction adjustment of the force on the bar that achieves almost the same muscle activity degree of the shoulder and elbow joints might be optimal BP kinetics.

Left ventricular (LV) longitudinal function is mechanically coupled to the elasticity of the ascending aorta (AA). The pathophysiologic link between stiff AA and reduced longitudinal strain and subsequent deterioration in longitudinal LV systolic function is likely relevant in heart failure with preserved ejection fraction (HFpEF). A proposed therapeutic effect of freeing the LV apex and allowing for LV inverse longitudinal shortening was studied in-silico utilizing Living Left Heart Human Model (Dassault Systémes Simulia Corporation). LV function was evaluated in a model with A) Elastic AA; B) Stiff AA; and C) Stiff AA with free LV apex. The cardiac model simulation demonstrated that freeing the apex caused inverse LV longitudinal shortening that can abolish the deleterious mechanical effect of a stiff AA on LV function. A stiff AA and impairment of LV longitudinal strain are common in patients HFpEF. The hypothesis-generating model strongly suggests that freeing the apex and inverse longitudinal shortening may improve LV function in HFpEF patients with a stiff AA.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

Axial compression tests were carried out on 6 square steel tube confined concrete short columns and 6 BFRP square pipe confined concrete axial compression tests. The concrete strength grades were C30, C40, and C50. The test results show that the failure modes of steel pipe and BFRP pipe are obviously different, and the BFRP pipe undergoes brittle failure. Compared with the short columns of concrete confined by BFRP pipes, the ultimate bearing capacity of axial compression is increased by -76.46%, -76.01%, and -73.06%, and the ultimate displacements are -79.20%, -80.78%, -71.71%.

To solve the problem of complex sensor installation and easy damage in contact displacement measurement, a non-contact measurement method of brace displacement in bridge swivel construction based on binocular vision is proposed in this study. Combined with monitoring data in a swivel construction interchange project, binocular vision system was compared and analyzed with the traditional displacement meter and total station. Results showed that force versus displacement variation plots were obtained by binocular visual measurement in the weighing test, the inflection point can be clearly distinguished, and the position of the inflection point was the same as that of the displacement meter; monitoring data of binocular vision measurement and total station were compared and analyzed in the bridge swivel process, the average error was no more than 0.18 mm, the maximum error was no more than 0.42 mm, and the standard deviation was no more than 0.12. The method proposed in this study can be used as an alternative to displacement meter and total station measurement methods in bridge swivel construction, the problem of complex sensor installation and easy damage is solved in brace displacement measurement, equipment and labor costs can be effectively saved.

Although evolutionary theory has yet to furnish a comprehensive rationale for the underlying mechanism of natural selection, it is pertinent to note that the phenomenon transcends the confines of biological systems, exhibiting analogous patterns in physical systems as well. Specifically, isolated and closed systems tend to evolve towards states of progressively increasing entropy. In scenarios where multiple paths for entropy increase are accessible, such systems tend to favor combinations of paths that exhibit the most rapid entropy increase rates. Among the various processes in nature, life activities constitute a salient means of achieving entropy increase. Genetic variation within organisms generates individuals that vary in their rates of entropy increase. As these organisms interact, compete and combine, they form diverse combinations of entropy-increasing pathways. Nature, in turn, selects among these combinations, favoring those that culminate in the fastest entropy increase, thereby propelling the evolution of life. Essentially, the evolution of life is an ongoing exploration of diverse combinations of pathways that maximize entropy increase across various energy pools. Amidst continuous genetic variation and the selective pressure imposed by nature for maximum entropy production rates, information accumulates, leading to a corresponding acceleration in the rate of entropy increase. This natural selection, which favors maximizing the entropy at the fastest possible rate, serves as the ultimate driving force for the origin and evolution of life.

This paper proposes the application of force-projecting bilateral control to a master-follower teleoperation system with a pneumatic manipulator on the follower side, and evaluates its effectiveness. The proposed method directly projects the operating force on the master side to the driving force on the follower side, eliminating the need for both position control and external force detection on the follower side, thereby solving the problem of low rigidity and response delay of pneumatic manipulators and providing highly stable sensor-less force presentation against variable environments. In this study, dynamic response analyses of a 1-DOF master-follower system were performed by numerical simulation using a linear system model, followed by experimental verification by implementing an actual system with an external force estimator. The results showed that the proposed force-projecting bilateral control has significantly higher positioning rigidity and better force control stability than the conventional force-reflecting bilateral control. A theoretical consideration was also given using equivalent transformation of force transfer functions to provide evidence for the high stability.